Tyan | Transport TA26 (B2932) | Specifications | Tyan Transport TA26 (B2932)

Tyan Transport TA26 (B2932)
Transport TA26
B2932
Service Engineer’s Manual
PREFACE
Copyright
This publication, including all photographs, illustrations, and software, is protected under international copyright laws, with all rights
reserved. Neither this manual, nor any material contained herein,
may be reproduced without written consent of the manufacturer-.
Copyright 2007
Version 1.0
Disclaimer
Information contained in this document is furnished by TYAN Computer Corporation and has been reviewed for accuracy and reliability
prior to printing. TYAN assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of
TYAN products including liability or warranties relating to fitness for
a particular purpose or merchantability. TYAN retains the right to
make changes to product descriptions and/or specifications at any
time, without notice. In no event will TYAN be held liable for any
direct or indirect, incidental or consequential damage, loss of use,
loss of data or other malady resulting from errors or inaccuracies of
information contained in this document.
Trademark Recognition
All registered and unregistered trademarks and company names
contained in this manual are property of their respective owners
including, but not limited to the following.
TYAN, Transport TA26 B2932, and Thunder n3600M are trademarks
of TYAN Computer Corporation.
AMD, Opteron, and combinations thereof are trademarks of AMD
Corporation.
AMI, AMIBIOS, and combinations thereof are trademarks of AMI
Technologies.
Microsoft, Windows are trademarks of Microsoft Corporation.
Marvell is a trademark of Broadcom Corporation and/or its
subsidiaries.
nVIDIA and nForce are trademarks of NVIDIA Corporation.
IBM, PC, AT, and PS/2 are trademarks of IBM Corporation.
Winbond is a trademark of Winbond Electronics Corporation.
Portable Document Format (PDF) is a trademark of Adobe
Corporation.
i
Federal Communications Commission (FCC)
Notice for the USA Compliance Information Statement (Declaration of Conformity Procedure) DoC FCC
Part 15: This device complies with part 15 of the FCC
Rules
Operation is subject to the following conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received including interference that may cause undesired operation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and the
receiver.
– Plug the equipment into an outlet on a circuit different from
that of the receiver.
Consult the dealer on an experienced radio/television technician for
help.
Notice for Canada
This apparatus complies with the Class B limits for radio interference
as specified in the Canadian Department of Communications Radio
Interference Regulations. (Cet appareil est conforme aux norms de
Classe B d’interference radio tel que specifie par le Ministere Canadien des Communications dans les reglements d’ineteference
radio.)
Notice for Europe (CE Mark) This product is in conformity
with the Council Directive 89/336/EEC, 92/31/EEC
(EMC).
CAUTION: Lithium battery included with this board. Do not puncture,
mutilate, or dispose of battery in fire. Danger of explosion if battery
is incorrectly replaced. Replace only with the same or equivalent
type recommended by manufacturer. Dispose of used battery
according to manufacturer instructions and in accordance with your
local regulations.
ii
About this Manual
This manual provides you with instructions on installing your Transport TA26 B2932. This manual is intended for experienced users
and integrators with hardware knowledge of personal computers.
This manual consists of the following parts:
Chapter 1:
Provides an Introduction to the TA26 B2932 barebone, packing list, describes the external components, gives a table of key components, and
provides block diagrams of the system.
Chapter 2:
Covers procedures on installing the CPU, memory modules, PCI/PCI-E/PCI-X cards, hard drives,
and floppy drive.
Chapter 3:
Covers removal and replacement procedures for
pre-installed components
Appendix:
Provides instructions on installing the SMDC card.
Describes the differences between mainboard
BIOS and system BIOS. The cable connection
and FRU parts tables are also provided for reference of system setup.
For information on the mainboard, please refer to the attached mainboard user’s manual. You can find the detailed description about
jumper and BIOS settings from the motherboard manual.
iii
SAFETY INFORMATION
Before installing and using the TA26 B2932, take note of the following precautions:
iv
–
–
–
Read all instructions carefully.
–
Only use the power source indicated on the marking label. If
you are not sure, contact the Power Company.
–
The unit uses a three-wire ground cable, which is equipped
with a third pin to ground the unit and prevent electric shock.
Do not defeat the purpose of this pin. If your outlet does not
support this kind of plug, contact your electrician to replace
your obsolete outlet.
–
Do not place anything on the power cord. Place the power
cord where it will not be in the way of foot traffic.
–
Follow all warnings and cautions in this manual and on the
unit case.
–
Do not push objects in the ventilation slots as they may touch
high voltage components and result in shock and damage to
the components.
–
When replacing parts, ensure that you use parts specified by
the manufacturer.
–
When service or repairs have been done, perform routine
safety checks to verify that the system is operating correctly.
–
Avoid using the system near water, in direct sunlight, or near
a heating device.
–
Cover the unit when not in use.
Do not place the unit on an unstable surface, cart, or stand.
Do not block the slots and opening on the unit, which are provided for ventilation.
Table of Contents
Chapter 1: Overview
1.1
1.2
1.3
1.4
1.5
About the TYAN Transport TA26 B2932 . . . . . . . . . . . . . . . . . . . 1
Product Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4.1 Box Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4.2 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
About the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.5.1 System Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.5.2 System Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.5.3 LED Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.5.4 Motherboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.5.5 Jumpers & Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.5.6 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.5.7 Internal View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 2: Setting Up
2.1
2.2
2.0.1 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.0.2 Work Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.0.3 Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.0.4 Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installing Motherboard Components. . . . . . . . . . . . . . . . . . . . . . . 15
2.1.1 Removing the Chassis Cover. . . . . . . . . . . . . . . . . . . . . . . 15
2.1.2 Installing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.1.3 Installing the Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.1.4 Installing PCI-E Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2.1.5 Installing Hard Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2.1.6 Installing a Floppy Drive . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.2.1 Installing the Server in a Rack. . . . . . . . . . . . . . . . . . . . . . 29
Chapter 3: Replacing Pre-Installed Components
3.1
3.2
3.3
3.4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.1.1 Work Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.1.2 Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.1.3 Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Removing the Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Replacing Motherboard Components . . . . . . . . . . . . . . . . . . . . . . 39
3.4.1 Disconnecting All Motherboard Cables . . . . . . . . . . . . . . 39
v
3.5
3.6
3.7
3.8
3.9
3.4.2 Removing the Motherboard . . . . . . . . . . . . . . . . . . . . . . . . 40
Replacing the Slim DVD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Replacing the LED Control Board . . . . . . . . . . . . . . . . . . . . . . . . 43
3.6.1 LED Control Board Features . . . . . . . . . . . . . . . . . . . . . . . 45
3.6.2 LED Control Board Connector Pin Definitions. . . . . . . . . 45
Replacing the Backplane. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.7.1 M1220 SAS/SATA Backplane Features . . . . . . . . . . . . . . . . 48
3.7.2 M1220 SAS/SATA Backplane Connector Pin Definitions. . 50
Replacing the System Fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Replacing the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
3.9.1 Standard Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
3.9.2 Optional 1+1 Redundant Power Supply . . . . . . . . . . . . . . 57
Appendix I: BIOS Differences
Appendix II: Cable Connection Tables
Appendix III: Installing the SMDC Card
Appendix IV: FRU Parts Table
vi
Chapter 1: Overview
1.1
About the TYAN Transport TA26 B2932
Congratulations on your purchase of the TYAN Transport
TA26 B2932, a highly-optimized rack-mountable barebone
system. The Transport TA26 B2932 is designed to support
AMD® Opteron™ 2000 1207-pin processor, providing a rich
feature set and incredible performance. Leveraging
advanced technology from AMD®, the Transport TA26 B2932
server system is capable of offering scalable 32 and 64-bit
computing, high-bandwidth memory design, and a lightningfast PCI-X bus implementation. The Transport TA26 B2932
not only empowers your company in today’s demanding IT
environment but also offers a smooth path for future application usage.
TYAN is also proud to deliver the Transport TA26 B2932 in
SAS flavor while supporting up to eight (8) hot-swap hard
drives and one (1) slim DVD-ROM drive. The Transport TA26
B2932 uses TYAN’s latest tooling-made chassis featuring a
robust structure, tool-less and modularized design, and a
solid mechanical enclosure. All of this provides the Transport
TA26 B2932 the power and flexibility to meet the needs of
nearly any server application.
1.2
Product Models
Model
HDD Bays
Backplane
Power Supply
B2932T26W8H
8
8-port
SAS/SATA
Single 600W
B2932T26W8HR
8
8-port
SAS/SATA
600W (1+1)
redundant
Chapter 1: Overview
1
1.3
Features
Enclosure
• Industry 2U rack-mountable chassis
• Storage bay:
– (8) 3.5” HDD bays
– (1) slim line ODD bay
• Dimensions:
– D 26 x W 16.7 x H 3.4 inch
– D 660 x W423 x H 87 mm
Motherboard
• TYAN Thunder n3600M S2932
• Extended ATX footprint (12” x 13”)
Processors
• Dual µ PGA1207-pin ZIF L1 sockets
• Supports one or two AMD®
Opteron™ 2000 series processors
Chipset
•
•
•
•
nVIDIA nForce Pro 3600
NEC nPD720400
SMSC DME5017
LSI 1068E
• One (1) PCI 32-bit 33MHz, v2.3
compliant slot
• Supports a total of six (6) low profile
cards
Back I/O Ports
• One keyboard & one PS/2 mouse
ports
• Two (2) USB 2.0 ports
• One 15-pin VGA port
• One 9-pin COM port
• Two RJ45 (Marvell 88E1121 PHY +
nVIDIA MAC)
Front Panel Features
• I/O
– (2) USB 2.0 ports
• LED indicators
– Power LED
– (2) LAN LEDs
– HDD Active LED
• Switches
– Power
– Reset
Memory
Storage Controller
• Dual memory channels
• SATA Controller
• Total sixteen (16) 240-pin 1.8-Volt
– Integrated six (6) SATA ports
DDRII DIMM sockets (8 on CPU1
– Serial ATA II Host controllers
and 8 on CPU2)
embedded
• Supports up to 64GB of registered
– NV RAID 0, 1, 0+1, 5 and JBOD
DDRII 667MHz
support
• Supports ECC type memory module
• SAS Controller
Video
– Eight (8) SAS ports
– LSI 1068E PCI-E SAS controller
• ATI® ES1000™ PCI graphics
– NV RAID 0, 1 and JBOD support
controller
• 32MB DDR Frame Buffer of video
Storage Backplane
memory
• One (1) 8-port SAS backplane,
BIOS
• AMI BIOS 8Mbit Flash
• Supports APM 2.0
• PnP, DMI 2.0, WfM 2.0 Power
Management
Expansion Slots
• Two (2) PCI-Express x16 slots
(each w/ x8 signal)
• Two (2) PCI-X 133/100MHz slot
• One (1) PCI-X 100MHz slot
2
supporting up to 8 SAS HDDs or
SATA HDDs
Networking
• Two 10/100/1000 Base-T LAN
(nForce Pro 3600 integrated MAC
with Marvell 88E1121 Gigabit
Ethernet PHY)
– IEEE802.3 compliant, WOL/PXE
support
– Pin header for front panel LAN
LED
Chapter 1: Overview
Server Management
• Automatic fan speed control
• Chassis intrusion alert
• Supports TYAN Server
Management (TSM)
• Optional TYAN SMDC M3291, IPMI
v2.0 compliant remote server
management kit
Power Supply
• EPS 12V, 2U, 600W with PFC for
B2932T26W8H
• EPS 12V, 2U, 600W 1+1 redundant
power with PFC for
B2932T26W8HR
Regulatory
• FCC Class B (Declaration of
Conformity)
• CE (Declaration of Conformity)
Environment Temperature
• Operating temperature 5oC~35oC
• Non-operating temperature -40oC~
70oC
Chapter 1: Overview
3
1.4
Unpacking
This section describes the TA26 B2932 package contents
and accessories. Open the box carefully and ensure that all
components are present and undamaged.
1.4.1 Box Contents
Component
Description
Industry standard 2U chassis, (8) hot-swap
HDD bays
TYAN Thunder n3600M S2932 motherboard
(pre-installed)
Slim DVD-ROM drive (pre-installed)
LED and USB control board (pre-installed)
EPS 12V, 2U, 600W PSU with PFC
(pre-installed) (A) (B2932T26W8H models)
A
B
EPS 12V, 2U, 600W (1+1) redundant PSU with
PFC (pre-installed) (B)
(B2932T26W8HR models)
System Fans:
1 x (60mm x 60mm) (A)
2 x (80mm x 80mm) (B)
A
4
B
Chapter 1: Overview
1.4.2 Accessories
If any items are missing or appear damaged, contact your
retailer or browse to TYAN’s Web site for service:
http://www.tyan.com.
The Web site also provides information on other TYAN products, plus FAQs, compatibility lists, BIOS settings, and more.
1 x TYAN Driver CD
2 x Heatsinks
Power Cables
Left to right: Europe, US
Unit Handles
FDD Cable
Chapter 1: Overview
Barebone Manual &
Mainboard Manual
5
FDD Rails
Screw Pack
FDD Power Cable
Sliding Rail
6
TYAN Logo
Chapter 1: Overview
1.5
About the Product
The following views show you the product.
1.5.1 System Front View
Reset switch
Power LED
ID switch
Power switch
Warning LED
USB ports
LAN LEDs
HDD activity LED
ID LED
HDD Tray
Power LEDs
DVD-ROM drive
Hard Drive Bay x 8
HDD Tray
Activity LEDs
1.5.2 System Rear View
Power Supply Fan
Power Supply Socket
PCI/PCI-E/PCI-X Slots
ID LED
PS/2 Mouse and
Keyboard Ports
2 USB Ports
Chapter 1: Overview
Serial VGA
Port
Port
GbE LAN Ports
(10/100/1000)
(Right: LAN1; Left: LAN2)
7
1.5.3 LED Definitions
Front Panel
LED
Color
State
Description
Power
Green
OFF
ON
OFF
Power ON
Power OFF
HDD Activity
Amber
Blinking
OFF
OFF
HDD/DVD-ROM
access activity
No disk activity
LAN1/LAN2/Linkage
Green
Green
OFF
ON
Blinking
OFF
LAN linked
LAN accessing
No LAN linked
Fail
Red
ON
OFF
OFF
System fails
Abnormal power off
Normal
Green
OFF
ON
OFF
Power connected
Power disconnected
SAS
HDD
Green
Green
OFF
ON
Blinking
OFF
HDD ready
HDD access activity
HDD not ready
SATA
HDD
Green
OFF
Blinking
OFF
HDD access activity
No disk activity
Hot Swappable HDD
Tray Power LED
Hot Swappable
HDD Tray Active LED
Rear I/O LED
*Right or Left is viewed from the rear.
LED
Color
State
Description
LAN1/LAN2 Linkage/
Activity (Left Side)
Green
Green
OFF
ON
Blinking
OFF
10Mb/100Mb/1000Mb linked
10Mb/100Mb/1000Mb activity
No LAN linked and activity
LAN1/LAN2 Linkage/
Activity (Right Side)
Yellow
1 Blinking
2 Blinking
3 Blinking
OFF
10Mb mode
100Mb mode
1000Mb mode
NO LAN linked and activity
Note: In 10 Mbps, the Right LED blinks yellow once in repeat and continuous action. In
100 Mbps, the Right LED blinks yellow twice in repeat and continuous action. So
does the condition in 1000 Mbps.
8
ID LED
Blue
OFF
ON
OFF
System is identified
System is not identified
Zippy Power
Supply LED
Green
Green
Amber
ON
1Hz Blinking
ON
Amber
1Hz Blinking
OFF
OFF
Output ON and OK
AC present/Only 5Vsb ON
Power supply critical event causing a
shutdown: failure, OCP, OVP, fan fail
Power supply warning event where
the power supply continues to operate: high temp., high power, high current, slow fan
No AC power
Chapter 1: Overview
1.5.4 Motherboard Layout
Chapter 1: Overview
9
1.5.5 Jumpers & Connectors
Jumper/
Connector
Function
JP1/ JP2
PCI-X1/ PCI-X2 Speed Setting Jumper
JP3/ JP4
ASF2.0/ SMDC Select Jumper
JP5
VGA Enable/ Disable Jumper
(Close 1-2) Default, enabled
(Close 2-3) Disabled
JP6
SAS Enable/ Disable Jumper
(Close 1-2) Default, enabled
(Close 2-3) Disabled
JP7
Clear CMOS Jumper
(Close 1-2) Default
(Close 2-3) Clear CMOS
J1
Keyboard/ Mouse Connectors
J2
VGA Connector
J3
COM Port Connector
J4/ J5
Gigabit LAN Port
J7/ J42/ J43/ J59/
J62
Chassis Fan Connectors
J59: FAN1, J62: FAN2, J42: FAN3, J43: FAN4, J7: FAN5
J8
COM Port Pin Header
J9/ J55
J55: CPUFAN1; J9: CPUFAN2 connectors
J10
Floppy Connector
J17
SMDC Connector
J18
IPMB Pin Header
PW1/ PW2/ PW3
Power Connectors
J38
LCM Pin Header (for barebone use only)
J39/ J63
TYAN Front Panel 2 Connector (for barebone use only)
J41
Front Panel USB2.0 Connectors
J61
Primary IDE Connector
J64
Front Panel Header
J65
SGPIO Header (for barebone use only)
J66
SAS Fault LED Pin Header (for barebone use only)
10
Chapter 1: Overview
1.5.6 System Block Diagram
Chapter 1: Overview
11
1.5.7 Internal View
15
1
14
2
3
13
4
5
12
6
11
FAN3
FAN2
FAN1
10
7
8
9
1.
2.
3.
4.
5.
6.
7.
8.
12
CPU2 Memory Slots
CPU2
Power Supply
Power Connector
CPU1 Memory Slots
CPU1
SAS/SATA Backplane
LED Control Board Cable
9. Eight (8) SAS/SATA HDD
trays
10. DVD-ROM Cable
11. System Fans (Right to Left:
FAN1, FAN2, FAN3)
12. SAS/SATA Cables (8)
13. PCI Slot
14. PCI-X Slots
15. PCI-E Slots
Chapter 1: Overview
Chapter 2: Setting Up
2.0.1 Before You Begin
This chapter explains how to install the CPU, CPU heatsink,
memory modules, hard drives, and floppy drive. Instructions
on inserting a PCI card are also given.
Take note of the precautions mentioned in this section when
installing your system.
2.0.2 Work Area
Make sure you have a stable, clean working environment.
Dust and dirt can get into components and cause malfunctions. Use containers to keep small components separated.
Putting all small components in separate containers prevents
them from becoming lost. Adequate lighting and proper tools
can prevent you from accidentally damaging the internal
components.
2.0.3 Tools
The following procedures require only a few tools, including
the following:
•
•
A cross head (Phillips) screwdriver
A grounding strap or an anti-static pad
Most of the electrical and mechanical connections can be disconnected using your fingers. It is recommended that you do
not use needle-nosed pliers to remove connectors as these
can damage the soft metal or plastic parts of the connectors.
Chapter 2: Setting Up
13
2.0.4 Precautions
Components and electronic circuit boards can be damaged
by discharges of static electricity. Working on a system that is
connected to a power supply can be extremely dangerous.
Follow the guidelines below to avoid damage to the
Transport TA26 B2932 or injury to yourself.
•
Ground yourself properly before removing the top
cover of the system. Unplug the power from the
power supply and then touch a safely grounded
object to release static charge (i.e. power supply
case). If available, wear a grounded wrist strap. Alternatively, discharge any static electricity by touching
the bare metal chassis of the unit case, or the bare
metal body of any other grounded appliance.
•
Avoid touching motherboard components, IC chips,
connectors, memory modules, and leads.
•
The motherboard is pre-installed in the system.
When removing the motherboard, always place it on
a grounded anti-static surface until you are ready to
reinstall it.
•
Hold electronic circuit boards by the edges only. Do
not touch the components on the board unless it is
necessary to do so. Do not flex or stress circuit
boards.
•
Leave all components inside the static-proof packaging that they ship with until they are ready for installation.
•
After replacing optional devices, make sure all
screws, springs, or other small parts are in place and
are not left loose inside the case. Metallic parts or
metal flakes can cause electrical shorts.
Notes:
• All connectors are keyed to only attach one way.
• Always use the correct screw size as indicated in the
procedures.
14
Chapter 2: Setting Up
2.1
Installing Motherboard Components
This section describes how to install components on to the
motherboard, including CPU, memory modules and PCI card.
2.1.1 Removing the Chassis Cover
Follow these instructions to remove the Transport TA26
B2932 chassis cover.
1. Turn the screw on the back side. Then slide the chassis
cover in the direction of arrow.
2. Lift off the cover.
Chapter 2: Setting Up
15
2.1.2 Installing the CPU
Follow these instructions to install the CPU.
1. Remove the one screw securing the pre-installed air
duct.
2. Remove the air duct and locate the two CPU socket on
the motherboard.
3. Remove the cover on the CPU socket.
16
Chapter 2: Setting Up
4. Lift up the CPU lever to unlock the socket.
5. Open the socket in the direction as illustrated.
6. Place the CPU in the CPU socket, ensuring that pin 1 is
located as shown below.
Chapter 2: Setting Up
17
7. Close the cover and press the CPU socket lever down to
secure the CPU.
8. Take out the new heatsink from the plastic case as shown
(A). Then remove the protective cover to reveal the preapplied thermal grease (B).
A
B
9. Align the heatsink screw holes with the holes on the
motherboard and insert two heatsink screws as shown.
10. Repeat these steps when installing a second CPU.
18
Chapter 2: Setting Up
2.1.3 Installing the Memory
Follow these instructions to install the memory modules on
the motherboard.
1. Remove the one screw securing the pre-installed air
duct.
2. Remove the air duct and locate the memory slots on the
motherboard.
3. Press the memory slot locking levers in the direction of
the arrows as shown below.
Chapter 2: Setting Up
19
4. Align the memory module with the slot. The module has
indentations that align with notches in the slots.
5. Insert the memory module into the slot as shown below.
When inserted properly, the memory slot locking levers lock
automatically onto the indentations at the ends of the
module.
20
Chapter 2: Setting Up
The following chart outlines the suggested rules for populating
memory.
Single CPU installed
(CPU1 only)
Population Option
1
2
Dual CPU installed
(CPU1 and CPU2)
3
4
7
8
CPU1_DIMM0
X
X
X
X
CPU1_DIMM1
X
X
X
X
CPU1_DIMM2
X
X
X
X
CPU1_DIMM3
CPU1_DIMM4
CPU1_DIMM5
X
X
X
X
X
5
6
X
X
X
X
X
X
X
X
X
X
X
CPU1_DIMM6
X
X
X
X
X
X
X
X
CPU1_DIMM7
X
X
X
X
X
X
X
X
CPU2_DIMM0
X
X
CPU2_DIMM1
X
X
CPU2_DIMM2
X
X
X
X
X
X
CPU2_DIMM3
CPU2_DIMM4
X
CPU2_DIMM5
X
X
X
CPU2_DIMM6
X
X
X
X
CPU2_DIMM7
X
X
X
X
NOTE:
1. X indicates a populated DIMM slot.
2. Symmetrical DIMMs must be identical.
- Same DRAM technology, e.g. 128-bit, 256-bit, etc.
- Same DRAM bus width, e.g. x8 or x16
- Matched Sided DIMMs (single-sided or double-sided)
Chapter 2: Setting Up
21
2.1.4 Installing PCI-E Cards
The TA26 B2932 has six PCI card slots:
1 x PCI card slot
2 x PCI-E card slots
3 x PCI-X card slots
Follow these instructions to install any of the above kinds of
add-in cards in your TA26 B2932 system.
1. Locate the PCI/PCI-E/PCI-X card slots on the motherboard. See “System Internal View” on page 14 for the
PCI/PCI-E/PCI-X slot locations.
2. Unscrew the bracket from the slot you want to use.
22
Chapter 2: Setting Up
3. Lift up the bracket.
4. Insert a PCI/PCI-E/PCI-X card into the appropriate slot.
Secure the card with the screw you removed from the
bracket.
Chapter 2: Setting Up
23
2.1.5 Installing Hard Drives
The TA26 B2932 supports up to eight serial SAS/SATA hard
drives. Follow these instructions to install a hard drive.
1. Press the locking lever latch in the direction shown by the
arrow below. The latch will pop open.
2. Slide the HDD tray out.
3. Unscrew the tray from the base as shown.
24
Chapter 2: Setting Up
4. Remove the base.
5. Place a hard drive into the drive tray.
6. Screw the hard drive in place using 4 HDD screws.
7. Reinsert the tray into the bay and press the locking lever
to secure.
Chapter 2: Setting Up
25
2.1.6 Installing a Floppy Drive
This section describes how to install a floppy disk drive in the
TA26 B2932 if required.
Follow these instructions to install a floppy disk drive in the
TA26 B2932.
1. Remove the top, left hand drive tray from the TA26
B2932 as shown.
Note: The top, left hand drive bay is the only bay that can
accommodate a floppy disk drive.
2. Attach the supplied FDD rails to the floppy disk drive with
six (6) M3L5, BIN (+) screws. The wide end of the rails
should be pointing towards the front.
26
Chapter 2: Setting Up
Note: The FDD rails each have a flat side which should be
against the body of the floppy drive when installed. There is
also a spring catch mechanism on the right hand rail (when
looking at the floppy disk drive from the front).
3. Plug the FDD power and data cables into the ports on the
back of the floppy disk drive.
4. Thread the cables out through the back of the empty
drive bay. Slide the floppy disk drive into the drive bay
until it clicks into place and fits flush with the front panel.
Chapter 2: Setting Up
27
5. Connect the other end of the power cable to the connector (J37) on the backplane.
6. Connect the other end of the supplied FDD cable to the
FDD slot (J10) on the motherboard.
Note: To release the floppy disk drive from the drive bay,
you will need to press the release catch inside the chassis.
28
Chapter 2: Setting Up
2.2
Rack Mounting
After installing the necessary components, the
Transport TA26 B2932 can be mounted in a rack using the
supplied rack mounting kit.
Rack mounting kit
Sliding Rails x 2
Mounting Ears x 2
Screws Kit x 1
Mounting Brackets x 4 (pre-installed)
2.2.1 Installing the Server in a Rack
Follow these instructions to mount the TA26 B2932 into an
industry standard 19" rack.
NOTE: Before mounting the Transport TA26 B2932 in a rack,
ensure that all internal components have been installed and
that the unit has been fully tested. Maintenance can be performed on the unit while in a rack but it is preferable to install
the device in a fully operational condition.
Screws List
No.
Size
Quantity
A
M4L6, S10C
(marked blue)
4
B
M6
8
C
M4-L5
18
Chapter 2: Setting Up
Screw
29
Attaching the Inner Rails to the Unit
7. Screw the handles to each side of TA26 B2932 as shown
using two (2) M4L6, S10C screws (A) from the supplied
screws kit.
8. Attach the inner rails both sides of the unit using nine (9)
M4-L5 screws (C) on each side.
30
Chapter 2: Setting Up
Installing Outer Rails to the Rack
1. Adjust the outer rail to match the length of the unit.
2. Secure the outer rail to the rack using 2 brackets and M6
screws (B) for each side. Secure the mounting brackets
from outside, not inside, of the rack.
Chapter 2: Setting Up
31
Rackmounting the Server
1. Draw out the middle rail to the latch position.
2. Lift the unit and then insert the inner slide rails into the
middle rails.
3. Push the unit in and press the latch key.
32
Chapter 2: Setting Up
4. Push the whole system into the rack.
5. Secure the mounting handles of the unit to the rack.
Note: To avoid injury, it is strongly recommended that two
people lift the TA26 B2932 into the place while a third person
screws it to the rack.
Chapter 2: Setting Up
33
34
Chapter 2: Setting Up
Chapter 3: Replacing Pre-Installed
Components
3.1
Introduction
This chapter explains how to replace pre installed components including the motherboard, LED control board, USB
adapter board, HDD, and DVD-ROM drive, etc.
Take note of the precautions in this section when installing
your system.
3.1.1 Work Area
Make sure you have a stable, clean working environment.
Dust and dirt can get into components and cause malfunctions. Use containers to keep small components separated.
Putting all small components in separate containers keeps
them from becoming lost. Adequate lighting and proper tools
can prevent you from accidentally damaging the internal
components.
3.1.2 Tools
The procedures that follow require only a few tools, including
the following:
•
•
A cross head (Phillips) screwdriver
A grounding strap or an anti-static pad
Most of the electrical and mechanical connections can be disconnected using your fingers. It is recommended that you do
not use needle-nosed pliers to remove connectors as these
can damage the soft metal or plastic parts of the connectors.
Chapter 3: Replacing Pre-Installed Components
35
3.1.3 Precautions
Components and electronic circuit boards can be damaged
by static electricity. Working on a system that is connected to
a power supply can be extremely dangerous. Follow the
guidelines below to avoid damage to the Transport TA26
B2932 or injury to yourself.
•
Ground yourself properly before removing the top
cover of the system. Unplug the power from your
computer power supply and then touch a safely
grounded object to release static charge (i.e. power
supply case). If available, wear a grounded wrist
strap. Alternatively, discharge any static electricity by
touching the bare metal chassis of the unit case, or
the bare metal body of any other grounded appliance.
•
Avoid touching motherboard components, IC chips,
connectors, memory modules, and leads.
•
The motherboard is pre-installed in the system.
When removing the motherboard, always place it on
a grounded anti-static surface until you are ready to
reinstall it.
•
Hold electronic circuit boards by the edges only. Do
not touch the components on the board unless it is
necessary to do so. Do not flex or stress circuit
boards.
•
Leave all components inside the static-proof packaging that they ship with until they are ready for installation.
•
After replacing optional devices, make sure all
screws, springs, or other small parts are in place and
are not left loose inside the case. Metallic parts or
metal flakes can cause electrical shorts.
Notes:
• All connectors are keyed to only attach one way.
• Always use the correct screw size as indicated in the
procedures.
36
Chapter 3: Replacing Pre-Installed Components
3.2
Disassembly Flowchart
The following flowchart outlines the disassembly procedure.
Rear Components
DIMMs
Chassis top cover
CPU/heatsink assembly
Mainboard
PCI card
Power supply
Mainboard
Front Components
Chassis top cover
DVD-ROM
PCBs
Control Board
FAN
Backplane
Note: The Transport TA26 B2932 should be always
powered off before disassembly.
Chapter 3: Replacing Pre-Installed Components
37
3.3
Removing the Cover
Before replacing any parts you must remove the chassis
cover.
Follow these instructions to remove the cover of the
Transport TA26 B2932 chassis cover.
1. Remove the screw on the back side. Then slide the chassis cover in the direction of arrow.
2. Lift off the cover.
38
Chapter 3: Replacing Pre-Installed Components
3.4
Replacing Motherboard Components
Follow these instructions to replace motherboard components, including the motherboard.
3.4.1 Disconnecting All Motherboard Cables
Before replacing the motherboard or certain components,
remove cables connected to the motherboard. Follow these
instructions to remove all motherboard cabling.
1. Disconnect power cables.
Main power cable
EPS 12V
power cables
2. Disconnect the DVD-ROM drive cable, TYFP cables,
SAS/SATA hard drive cables, and USB cable.
USB cable
TYFP cable
DVD-ROM cable
TYFP cable
(For SATA cables)
SAS cables
Chapter 3: Replacing Pre-Installed Components
39
3.4.2 Removing the Motherboard
After removing all of the aforementioned cables, follow these
instructions to remove the motherboard from the chassis.
1. Remove the eight screws securing the motherboard to
the chassis.
2. Remove the motherboard.
40
Chapter 3: Replacing Pre-Installed Components
3.5
Replacing the Slim DVD-ROM
Follow these instructions to replace the DVD-ROM.
1. Remove the FFC cable from the rear of the DVD-ROM
drive.
2. Press the tab in the direction shown to release the DVDROM drive.
3. Push the DVD-ROM drive through the front of the TA26
B2932.
Chapter 3: Replacing Pre-Installed Components
41
4. Remove the two screws that secure DVD-ROM drive to
the backplane.
5. Replace the DVD-ROM drive.
6. Secure the DVD-ROM to the backplane using two
screws. Then replace the unit into the drive bay and connect the DVD-ROM FFC cable.
42
Chapter 3: Replacing Pre-Installed Components
3.6
Replacing the LED Control Board
Follow these instructions to replace the LED control board.
1. Remove the screw securing the LED control board unit to
the chassis.
2. Remove the connector cables from the backplane.
3. Slide back the LED control board bracket and lift free of
the chassis.
Chapter 3: Replacing Pre-Installed Components
43
4. Remove the LED control board and USB cables from the
LED control board and USB adapter board.
5. Remove the five screws securing the LED control board
and USB adapter board to the bracket.
6. Release the LED control board and USB adapter board
from bracket. After replacement, insert and secure the
unit to the chassis following the above procedure in
reverse.
44
Chapter 3: Replacing Pre-Installed Components
3.6.1 LED Control Board Features
S3 power switch
JB1
SYSTEM
HEADER
S2 ID switch
S1 reset switch
D6 power LED
D5 HDD LED
D4 W/L LED
D3 ID LED
D2 LAN2 LED
D1 LAN1 LED
3.6.2 LED Control Board Connector Pin Definitions
JB1 2x12 Pin Output Connector
1
LAN1 GR-LED +
2
LAN1-LED -
3
Reserved
4
Reserved
5
LAN2 GR-LED +
6
LAN2-LED -
7
Reserved
8
Reserved
9
Reserved
10
Reserved
11
ID-LED +
12
ID-LED -
13
W-LED +
14
W-LED -
15
Local HDD led +
16
Local HDD led -
17
System power led +
18
System power led -
19
System reset switch +
20
System reset switch -
21
ID-switch +
22
ID-switch -
23
System power switch +
24
System power switch -
Chapter 3: Replacing Pre-Installed Components
45
3.7
Replacing the Backplane
Follow these instructions to replace the backplane in your
TA26 B2932 system.
1. Remove all of cables connected to the backplane, including fan cables, DVD-ROM cables, LED control board
cables, fan control cable, TYFP cable, USB cables, front
panel LED cables, power cables, and SAS/SATA cables.
Power cables
Fan cables
Slim DVD-ROM
FFC cable
LED control
board cable
USB cable
DVD-ROM cable
Fan control cable
TYFP cable
USB cable
Front panel LED cables
46
SAS/SATA cables
Chapter 3: Replacing Pre-Installed Components
2. Remove the ten screws to release the backplane.
3. Turn the locking keys at the base of the backplane as
shown.
4. Pull out the backplane.
5. Place a new backplane in position and secure in place
with the ten screws and locking keys released in step 2
and 3.
6. Reconnect all the cables to the backplane.
Chapter 3: Replacing Pre-Installed Components
47
3.7.1 M1220 SAS/SATA Backplane Features
Front View
J35 2x7pin
LED
J13 29pin SAS
J14 29pin SAS
J15 29pin SAS
J34 2x5pin LED
J11 29pin SAS
J12 29pin SAS
J7 40pin
cd-rom/B
J33 2x12pin
LED/B
J5 2x5pin USB
J36 2x7pin
LED
J8 29pin SAS
J9 29pin SAS
J10 29pin SAS
48
Chapter 3: Replacing Pre-Installed Components
Rear View
J1,J2,J3
big 4pin
FAN1 4pin
J25,J27,J29,J31
7pin secondary
J24,J26,J28,J30
7pin primary
J38 2x7pin
tach and PWM
J6 TO
CD-ROM
FAN2 4pin
J37 small
4pin
FAN3 4pin
J17,J19,J21,J23
7pin secondary
J32 LED/B
J16,J18,J20,J22
7pin primary
J4 USB OUT
Chapter 3: Replacing Pre-Installed Components
49
3.7.2 M1220 SAS/SATA Backplane Connector Pin Definitions
J32, J33 2x12pin LED board connector
1
LAN1 LED + (link/active)
2
LAN1 LED - (link/active)
3
Reserved
4
Reserved
5
LAN2 LED + (link/active)
6
LAN2 LED - (link/active)
7
Reserved
8
Reserved
9
Reserved
10
Reserved
11
ID-LED +
12
ID-LED -
13
W-LED +
14
W-LED -
15
M/B HDD LED +
16
M/B HDD LED -
17
M/B power LED +
18
M/B power LED -
19
M/B reset switch +
20
M/B reset switch -
21
ID-switch +
22
ID-switch -
23
M/B power switch +
24
M/B power switch -
J7 SILM IDE 40pin Front Panel Connector
50
1
RESET
2
GND
3
D7
4
D8
5
D6
6
D9
7
D5
8
D10
9
D4
10
D11
11
D3
12
D12
13
D2
14
D13
15
D1
16
D14
17
D0
18
D15
19
GND
20
VCC
21
DMARQ
22
VCC
23
DIOW
24
VCC
Chapter 3: Replacing Pre-Installed Components
25
DIOR
26
VCC
27
IORDY
28
CSEL
29
DMACK
30
VCC
31
INTRQ
32
IOCS16
33
DA1
34
PDIAG
35
DA0
36
DA2
37
CS1FX
38
CS3FX
39
DASP
40
VCC
Fan Signal Related Connector Pin Definitions
Note: The FAN signal naming is based on HW circuit
design only. It might be different from the system fan name.
FAN1, FAN2, FAN3: 4-pin Fan connector
1
GND
2
VDD +12V
3
TACH
4
PWM
J1, J2 and J3 power big 4-pin connector
1
VDD +12V
2
GND
3
GND
4
VCC +5V
Chapter 3: Replacing Pre-Installed Components
51
J4, J5 USB 2x5pin connector
1
USB1 power +
2
USB2 power +
3
USB1 DATA -
4
USB2 DATA -
5
USB1 DATA +
6
USB2 DATA +
7
USB1 GND
8
USB2 GND
9
Key pin
10
None
J37 power small 4-pin connector
1
+5V
2
GND
3
GND
4
+12V
J36 HDD LED pin out
1
PLED1
2
GND
3
ALED1
4
ALED1 +
5
PLED2 +
6
GND
7
ALED2 -
8
ALED2 +
9
PLED3 +
10
GND
11
ALED3 -
12
ALED3+
13
None
14
Key
J34 HDD LED pin out
52
1
PLED4 +
2
GND
3
ALED4 -
4
ALED4 +
5
PLED5 +
6
GND
7
ALED5 -
8
ALED5 +
9
None
10
Key
Chapter 3: Replacing Pre-Installed Components
J35 HDD LED pin out
1
PLED6 +
2
GND
3
ALED6 -
4
ALED6 +
5
PLED7 +
6
GND
7
ALED7 -
8
ALED7 +
9
PLED8 +
10
GND
11
ALED8 -
12
ALED8 +
13
None
14
Key
J38 2x7pin FAN tach and PWM pin out
1
FAN1 tach
2
Reserved
3
FAN2 tach
4
Reserved
5
FAN3 tach
6
Reserved
7
Reserved
8
Reserved
9
Reserved
10
Reserved
11
GND
12
KEY
13
GND
14
PWM input
Chapter 3: Replacing Pre-Installed Components
53
3.8
Replacing the System Fan
Follow these instructions to replace the cooling fans in your
TA26 B2932 system.
1. Locate the fan connector on the backplane and unplug
the fan cable as shown below.
2. Take the fan away from the chassis.
3. Replace a new fan into the chassis following the above
steps in reverse.
54
Chapter 3: Replacing Pre-Installed Components
3.9
Replacing the Power Supply
Follow these instructions to replace the power supply in your
TA26 B2932 system.
3.9.1 Standard Power Supply
1. Remove the chassis cover. See “Removing the Cover” on
page 38 for more details.
2. Detach the power cables from the motherboard and
backplane. See “Disconnecting All Motherboard Cables”
on page 39 for more details.
3. Remove the three screws securing the power supply to
the chassis.
Chapter 3: Replacing Pre-Installed Components
55
4. Remove the two screws attaching the power supply to
the chassis interior and lift out the unit.
5. Lift the power supply free from the chassis.
6. Replace a new power supply into the chassis following
the above steps in reverse.
56
Chapter 3: Replacing Pre-Installed Components
3.9.2 Optional 1+1 Redundant Power Supply
If the optional 1+1 redundant power supply is fitted, either of
the two units can be hot swapped. Follow these instructions
to replace a single power unit with a redundant power supply
unit.
Note: Before proceeding, remove the new redundant
power supply from its packaging.
1. Release thumb screws of the redundant power supply
and push the latch bar to the left. Pull both two power
modules out.
2. Remove the screws which fix the bracket to the sides of
the redundant power supply casing.
Chapter 3: Replacing Pre-Installed Components
57
3. Screw the bracket to the rear of the power supply casing.
4. Insert the redundant power supply casing into the chassis, making sure it is aligned as shown.
5. Screw the casing to the chassis exterior.
58
Chapter 3: Replacing Pre-Installed Components
6. Screw the casing to the chassis interior.
7. Fix the redundant power supply switch to the chassis rear
window with two Hex #6-32 screws.
8. Insert the new power supply unit and secure by turning
the locking screw.
Chapter 3: Replacing Pre-Installed Components
59
9. Re-attach all power supply connector cables to the motherboard and backplane.
60
Chapter 3: Replacing Pre-Installed Components
Appendix I: BIOS Differences
The BIOS of B2932 is similar to the BIOS of S2932. There is
only one menu different. See the following for the differences
in BIOS between B2932 and S2932. For a complete review of
S2932 BIOS, refer to the motherboard manual.
B2932 Advanced/Hardware Health Configuration
BIOS Setup Utility
Advanced
Hardware Health Configuration
H/W Health Function
CPUFAN1, 2 FAN1,2 PWM Control
FAN Fail LED Indicator
Enables Hardware
Health Monitoring
Device.
[Enabled]
[Disabled]
[Enabled]
Hardware Health Event Monitoring
X Mainboard Voltages Report
CPU1 Temperature
CPU2 Temperature
Ambient Temp (Near NEC)
Ambient Temp (Near MCP55)
:xx ºC/ xxx ºF
:xx ºC/ xxx ºF
:xx ºC/ xxx ºF
:xx ºC/ xxx ºF
System FAN1 Speed (TACH6)
System FAN2 Speed (TACH7)
System FAN3 Speed (TACH9)
:xxxx RPM
:xxxx RPM
:xxxx RPM
ÅÆ
ÇÈ
+/ F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
61
S2932 Advanced/Hardware Health Information
BIOS Setup Utility
Advanced
Hardware Health Configuration
H/W Health Function
CPUFAN1, 2 FAN1,2 PWM Control
FAN3, FAN4, FAN5 PWM Control
FAN Fail LED Indicator
Enables Hardware
Health Monitoring
Device.
[Enabled]
[Disabled]
[Disabled]
[Disabled]
Hardware Health Event Monitoring
X Mainboard Voltages Report
CPU1 Temperature
CPU2 Temperature
Ambient Temp (Near NEC)
Ambient Temp (Near MCP55)
:xx ºC/ xxx ºF
:xx ºC/ xxx ºF
:xx ºC/ xxx ºF
:xx ºC/ xxx ºF
CPU1 FAN1 Speed (TACH1)
CPU1 FAN2 Speed (TACH2)
FAN1 Speed (TACH3)
FAN2 Speed (TACH4)
FAN3 Speed (TACH5)
FAN4 Speed (TACH6)
FAN5 Speed (TACH7)
:xxxx RPM
:xxxx RPM
:xxxx RPM
:xxxx RPM
:xxxx RPM
:xxxx RPM
:xxxx RPM
ÅÆ
ÇÈ
+/ Tab
F1
F10
ESC
Select Screen
Select Item
Change Option
Select Field
General Help
Save and Exit
Exit
Table of Differences
S2932
B2932
FAN Fail LED
Indicator
Disabled
Enabled
Hardware Monitor Fan
CPU1 Fan1 Speed
CPU1 Fan2 Speed
FAN1 Speed
FAN2 Speed
FAN3 Speed
FAN4 Speed
FAN5 Speed
System FAN1 Speed (TACH6)
System FAN2 Speed (TACH7)
System FAN3 Speed (TACH9)
62
Appendix II: Cable Connection Tables
SAS/SATA Cable
Table 1: TA26 B2932 Model
M1220 SAS/SATA
Backplane
Connects to
Motherboard
J16
Æ
SAS0
J18
Æ
SAS1
J20
Æ
SAS2
J22
Æ
SAS3
J24
Æ
SAS4
J26
Æ
SAS5
J28
Æ
SAS6
J30
Æ
SAS7
FAN Cable
Table 2: System Fan to Backplane
System Fan
Connects to
M1220 SAS/SATA
Backplane
Fan 1
Æ
FAN1 4-pin connector
Fan 2
Æ
FAN2 4-pin connector
Fan 3
Æ
FAN3 4-pin connector
63
Power Supply Cable
Table 3: Power Supply to Motherboard
Power Supply
Connects to
Motherboard
P1 24-pin power cable
Æ
PW1 24-pin connector
P2 8-pin power cable
Æ
PW2 8-pin connector
P3 4-pin power cable
Æ
PW3 4-pin connector
Table 4: Power Supply to Backplane
Power Supply
Connects to
M1220 SAS/SATA
Backplane
P3 4-pin power cable
Æ
J1 4-pin connector
P3 4-pin power cable
Æ
J2 4-pin connector
P3 4-pin power cable
Æ
J3 4-pin connector
Other Cables
Table 5: Backplane to Motherboard
M1220 SAS/SATA
Backplane
Connects to
J32 LED/B
Æ
J4 USB OUT
Æ
J41
J6 TO CD-ROM
Æ
J61
J38
2x7pin Tach and PWM
Æ
J63
Motherboard
J64
J39
Table 6: Backplane to LED Control Board
M1220 SAS/SATA
Backplane (Rear side)
J33 2x12pin LED/B
J5 2x5pin USB
64
Connects to
LED Control Board
Æ
JB1 SYSTEM HEADER
Table 7: System Internal LED Cables to Backplane
M1220 SAS/SATA
Backplane (Front side)
Connects to
TA26 B2932 System
Æ
System Internal
LED Cables
J34 2x5pin LED
J35 2x7pin LED
J36 2x7pin LED
Table 8: DVD-ROM Related Cable
M1220 SAS/SATA
Backplane
Connects to
DVD-ROM Backplane
J7
slim DVD connector
Æ
DVD-ROM Backplane
Table 9: FDD Related Cables
Motherboard FDD
connector
Æ
FDD Drive
M1220 SAS/SATA
Backplane
J37 4-pin connector
Æ
FDD Drive
65
Appendix III: Installing the SMDC Card
The following provides you with the information on installing
M3291 SMDC card into a PCI or PCI-X slot in your TA26
B2932 system.
1. Locate the TX/RX and RTS/CTS switch jumpers (J3 and
J4) on the SMDC card, and place the jumper caps to
close pins 5-8.
2. Secure M3291 on a low profile PCI bracket as shown.
3. Connect the 2x25 pin SMDC cable to M3291 as shown.
66
4. Unscrew the bracket from the slot as shown. Lift up the
bracket.
5. Connect the other end of SMDC cable to the SMDC connector (J18) on the motherboard.
6. Place the SMDC card in the PCI or PCI-X slot as shown.
67
7. Secure the PCI bracket with the screw you removed from
the card slot cover.
Cable Connection Table
68
SMDC Card (M3291)
Connects to
Motherboard
J1 connector
Æ
J17 SMDC connector
Appendix IV: FRU Parts Table
Item
Model
Number
Picture
Quantity
Description
Motherboard
S2932WG2
NR
1
TYAN
S2932WG2NR
Motherboard
Chassis Unit
CCHA-0090
1
Chassis unit,
Maryang2000
CCCV-0020
1
Top cover, Mitac
Maryang2000
CHDT-0030
8
HDD Carrier,
External
CFAN-0250
2
80x80x38mm,
FFC0812DE-7N20
CFAN-0200
1
60x60x38mm,
FFB0612EHE-6A46
CRAL-0040
1
Rail Kit, 4708-3-28
EZP
CEAR-0100
1
Mounting Ear Left
CEAR-0110
1
Mounting Ear Right
CDVD-0020
1
Slim DVD-ROM;
DVD DRIVE; DV28E-N93
CPCA-0250
1
Slim DVD-ROM
Adapter Board
Chassis &
Metal Parts
FAN
Sliding Rails
& Mounting kit
Mounting Ear
Peripheral
Drives &
backplane
69
Item
Model
Number
Picture
Quantity
Description
Storage
Backplane
M1220
1
PCB ASSY; 2U,
8BAY, SAS
BACKPLANE
M1220
Heat Sink &
Cooler
CHSK-0280
2
CPU Cooler
Air Duct
CADT-0160
1
AIR_DUCT;
PC+ABS, for TA26
1
R2W-5600P3V,
600W 1+1
redundant, for
B2932T26W8HR
CPSU-0170
1
P2M-6600P, 600W
Single Power
Supply, for
B2932T26W8H
CPCA-0270
1
Front Panel
LED/SWITCH/ID
LED Board
CPCA-0080
1
USB Adapter
Board, 2-port, for
TA26
CCBL-0310
1
A/C Power Cord,
L=1830mm, US
type
CCBL-0300
1
A/C Power Cord,
L=1830mm,
Germany type
CCBL-0671
1
SAS Cable, 4x7P to
4x7P, L=400mm
CCBL-0675
1
SAS Cable, 4x7P to
4x7P, L=300mm
CCBL-0130
1
Slim CD-ROM FFC,
40-Pin, for TA26
CPSU-0180
Power Supply
Front Panel
Board
Cable Set
70
Item
Model
Number
Picture
Quantity
Description
CCBL-0090
2
HDD LED Cable
Assembly, 10-pin,
200mm, for TA26
CCBL-0100
1
HDD LED Cable
Assembly, 14-pin,
200mm, for TA26
CCBL-0111
1
Control Board
Cable,
TYFP1/TYFP2,
TYFP1
375mm/TYFP2
315mm
CCBL-0144
1
Chassis Intrusion
Cable L=800mm
CCBL-0750
1
USB cable, MB to
backplane, 300mm,
for TA26
CCBL-0200
1
USB cable,
backplane to LED
board, 130mm, for
TA26
CCBL-0120
1
LED Board Cable
CCBL-0433
1
DVD ROM Cable
CCBL-0842
1
FAN Control Cable
L=350mm
CCBL-0810
1
Floppy Cable,
L=610mm
CCBL-0820
1
Floppy Power
Cable, L=90mm
Cable Set
71
Technical Support
If a problem arises with your system, you should first turn to
your dealer for direct support. Your system has most likely
been configured or designed by them and they should have
the best idea of what hardware and software your system
contains. Hence, they should be of the most assistance for
you. Furthermore, if you purchased your system from a
dealer near you, take the system to them directly to have it
serviced instead of attempting to do so yourself (which can
have expensive consequences).
If these options are not available for you then TYAN Computer Corporation can help.Besides designing innovative and
quality products for over a decade, TYAN has continuously
offered customers service beyond their expectations. TYAN's
website
(www.tyan.com) provides easy-to-access resources such as
in-depth Linux Online Support sections with downloadable
Linux drivers and comprehensive compatibility reports for
chassis, memory and much more. With all these convenient
resources just a few keystrokes away, users can easily find
the latest software and operating system components to keep
their systems running as powerful and productive as possible. TYAN also ranks high for its commitment to fast and
friendly customer support through email. By offering plenty of
options for users, TYAN serves multiple market segments
with the industry's most competitive services to support them.
"TYAN's tech support is some of the most impressive we've
seen, with great response time and exceptional organization
in general" - Anandtech.com
Please feel free to contact us directly for this service at techsupport@tyan.com
Help Resources:
1. See the beep codes section of this manual.
72
2. See the TYAN website for FAQ’s, bulletins, driver updates,
and other information: http://www.tyan.com
3. Contact your dealer for help BEFORE calling TYAN.
4. Check the TYAN user group: alt.comp.periphs.mainboard.TYAN
Returning Merchandise for Service
During the warranty period, contact your distributor or system
vendor FIRST for any product problems. This warranty only
covers normal customer use and does not cover damages
incurred during shipping or failure due to the alteration, misuse, abuse, or improper maintenance of products.
NOTE: A receipt or copy of your invoice marked with the date
of purchase is required before any warranty service can be
rendered. You may obtain service by calling the manufacturer
for a Return Merchandise Authorization (RMA) number. The
RMA number should be prominently displayed on the outside
of the shipping carton and the package should be mailed prepaid. TYAN will pay to have the board shipped back to you.
TYAN Transport TA26 B2932 User’s Manual v1.0
Document part No. D1867-100
73
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising