User manual | Broadcasting, radio, Audio Katalog _ GES

Online PDF katalog GES-ELECTRONICS
Vygenerováno: 25. 3. 2014
Broadcasting, radio, Audio
HF Wire Antennas
Antennas and Accessories
MFJ-1777 MULTIBAND ANTENNA
HF Omnidirectional Verticals
GES08900500
Allband wire antenna 160-6m, only 32m long, 1500W, ladder line
31m
Antenna Masts
MFJ-1908 FIBER GLASS
TELESCOPING MAST
AV-12AVQ TRAPED VERTICAL
ANTENNA 10-15-20M
GES08901203
HY-GAIN traped vertical 10/15/20m; 50 Ohm; m ax.1500W PEP;
h=4m; 4kg; 130km/h
GES08902107
Super-strong, 43 Feet Fiberglass Mast with Hose Clamps
Needs a ballanced l ine tuner ( MFJ969 or MFJ974HB or MFJ976 for 160-6m,
MFJ902H or MFJ904H or MFJ962 for 80-10m and many others MFJ types or a
standard 50 Ohm tuner wi th suitable 4:1 current balun (such as MFJ912 ).
See chapter Amateur radio - Tuners.
1 pc: 1 595 Kč
RoHS
MFJ-1778 G5RV ANTENNA
Thi s is a super-strong heavy duty telescopi ng MAST, not a fli msy pol e! Made
of .125 inch thick wal l fiberglass tubing. 2-inch O.D. bottom section, 3/4 inch
O.D. top section. Supports real weight i ncluding small yagis, vertical s, loops,
ful l-size dipoles, G5RVs. The MFJ-1906 sections are secured together usi ng
Stainl ess Steel hose clamps 43 feet extended, 8 feet col lapsed, six 8-ft.
sections, 16 lbs.
GES08900501
G5RV (160m) 80/40/30/20/17/15/12/10m antenna, feeder
inclusive; 1500W
When mounting the antenna more than 1m above ground, a resonant radi al
system must be used, such as HY-GAIN's AV-14RMQ Radial System Kit.
1 pc: 3 695 Kč
RoHS
AV-14AVQ TRAPED VERTICAL
ANTENNA 10/15/20/40M
GES08901204
HY-GAIN traped vert10/15/20/40m ;50Ohm ;max.1500W
PEP;h=5,4m;5kg;130km/h
1 pc: 4 790 Kč
RoHS
HF Magnetic Loop Antennas
MFJ-1786X LOOP MAGNETICAL
AUTOMATICAL ANTENNA
GES08900509
10-30MHz Super Hi-Q Loop; 36"diam.; Autotuner + Cross-Needle
Wattmeter; 150W
The popular antenna i s a multi-band center-feed dipol e antenna for HF
10-80m. Works on 160m as a Marconi antenna - the bottom end of the feeder
and any vertical coax shoul d be connected together. Consists of a 102"
(31.2m) flat top fed wi th a 32.5" (9.9m) 450 Ohm ladder matchi ng secti on
ending in a SO-239 coaxial connector. Typi cal SWR is 2:1, any good antenna
tuner is necessary. A good automatical tuner or a standard tuner you find in
chapter Amateur radi o - Tuners. A ferrite choke type balun (FEC) should be
used with thi s antenna to eli mi nate or reduce undesirable parallel feed li ne
RF currents. Fail ure to use a choke may result in RFI, RF feedback, or other
symptoms of RF "i n the shack".
1 pc: 1 285 Kč
RoHS
MFJ-1778M JUNIOR G5RV
ANTENNA
MFJ's tiny 36 i nch diameter loop antenna l ets you operate 10 through 30
MHz conti nuously - includi ng WARC bands. Ideal for limited space apartments, smal l lots, atti cs or motor homes. Enj oy both DX and l ocal
contacts mounted verti cally. Get both low angle radiation for excel lent DX
and high angle radiation for local, close-in contacts. Handles 150 Watts.
Super easy-to-use! Onl y MFJ's super remote control has Auto Band Sel ection.
It auto-tunes to desired band, then beeps to let you know. No control cable
needed. Needs no-grounded power supply (we recommend any type MW 12V
). Fast/Slow tune buttons and buil t-in two range Cross-Needl e SWR/Wattmeter
lets you quickly tune to your exact frequency. All welded constructi on, no
mechanical joints, welded butterfl y capacitor with no rotati ng contacts, large
1.050 i nch diameter round radiator - not a l oosy thing flat - gives you highest
possibl e efficiency. Each plate in MFJ's tuni ng capacitor is wel ded for l ow loss
and pol ished to prevent high vol tage arcing, welded to the radi ator, has nyl on
beari ng, anti-backsl ash mechani sm, limit switches, conti nuous no-stel DC
motor - gi ves smooth precisi on tuning. Heavy duty thi ck plastic housing has
ultraviolet inhi bitor protection.
GES08900502
1 pc: 13 250 Kč
RoHS
1 pc: 2 120 Kč
RoHS
AV-18AVQII TRAPED VARTICAL
ANTENNA 10/15/20/40/80M
GES08901206
When mounting the antenna more than 1m above ground, a resonant radi al
system must be used, such as HY-GAIN's AV-14RMQ Radial System Kit.
1 pc: 6 890 Kč
RoHS
AV-18VS MULTIBAND VERTICAL
ANTENNA
GES08901208
HY-GAIN vertical, manually tuned from 10 to 80m; max1,5kW PEP;
h=5.4m;2kg
GES08900511
MFJ's tiny 36 i nch diameter loop antenna l ets you operate 15 through 40
Meters continuousl y - incl uding WARC bands. Ideal for li mi ted space apartments, smal l lots, atti cs or motor homes. Enj oy both DX and l ocal
contacts mounted verti cally. Get both low angle radiation for excel lent DX
and high angle radiation for local, close-in contacts. Handles 150 Watts.
Super easy-to-use! Onl y MFJ's super remote control has Auto Band Sel ection.
It auto-tunes to desired band, then beeps to let you know. No control cable
needed. Needs no-grounded power supply (we recommend a type MW 12V ).
Fast/Sl ow tune buttons and built-in two range Cross-Needle SWR/Wattmeter
lets you quickly tune to your exact frequency. All welded constructi on, no
mechanical joints, welded butterfl y capacitor with no rotati ng contacts, large
1.050 i nch diameter round radiator - not a l oosy thing flat - gives you highest
possibl e efficiency. Each plate in MFJ's tuni ng capacitor is wel ded for l ow loss
and pol ished to prevent high vol tage arcing, welded to the radi ator, has nyl on
beari ng, anti-backsl ash mechani sm, limit switches, conti nuous no-stel DC
motor - gi ves smooth precisi on tuning. Heavy duty thi ck plastic housing has
ultraviolet inhi bitor protection.
GES08901218
HY-GAIN 80m set for AV14AVQ (for SWR 2:1 band-width
40kHz/80m)
HY-GAIN traped 5band vertical 10/15/20/40/80m, 1500W PEP max.
1 pc: 11 930 Kč
7-21MHz Super Hi-Q Loop; 36"diam.; Autotuner + Cros s-Needle
Wattmeter; 150W
MK-80 SET 80M FOR AV14AVQ
Junior G5RV 40-10m antenna, feeder inclus ive; 1500W
RoHS
MFJ-1788X LOOP MAGNETICAL
AUTOMATICAL ANTENNA
1 pc: 4 990 Kč
RoHS
The shorted version of the popular G5RV antenna is a multi-band center-feed
dipol e antenna for HF 10-80m. Consists of a 52' (15.9m) flat top fed with a
17'(5.2m) 450 Ohm ladder matching section ending in a SO-239 coaxial
connector. Typi cal SWR i s 2:1, any good antenna tuner is necessary. A good
automatical tuner or a standard tuner you find in chapter Amateur radio Tuners. A ferri te choke type bal un (FEC) should be used with this antenna to
eli mi nate or reduce undesirabl e parallel feed line RF currents. Fail ure to use
a choke may result in RFI, RF feedback, or other symptoms of RF "i n the
shack".
1 pc: 990 Kč
Action
RoHS
Antena is manual ly tuned to desired band by a simple adjustement of the
feed point on the base i nductor. When mounti ng the antenna more than
1.5m above ground, a resonant radial system must be used, such as
HY-GAIN's AV-14RMQ Radial System Kit.
1 pc: 3 290 Kč
RoHS
AV-14RMQ RADIAL SET
GES08901205
HY-GAIN radial set for AV12AVQ, AV14AVQ, AV18VS, AV18AVQII
1 pc: 2 390 Kč
RoHS
AV-18HT MULTIBAND VERTICAL
ANTENNA
AV-640 MULTIBAND VERTICAL
ANTENNA 8-BANDS 6-40M
GES08901210
R8 MULTIBAND VERTICAL
ANTENNA 8-BANDS
GES08902135
HY-GAIN 8-Band vertical 6/10/12/15/17/20/30/40m; 3dBi; 1500W
PEP; 7.6m; 11kg; 125km/h
8-Band vertical 6/10/12/15/17/20/30/40m; 3dBi; 1500W PEP (750W
CW); 8.7m; m ax 80m ph; 11kg
HY-GAIN's new AV-640 Patriot HF Vertical is the best buil t, best performing,
low radiating angle and best priced multiband vertical avail able today. Need
no external radi als. Hy-Gain is proud to deliver the AV-640 Eight Band
Vertical. Drawing on our many years of Amateur Radi o HF and VHF antenna
design experience, we have produced a wel l-engineered antenna capable of
maximum effi ci ency, unmatched performance, and superior construction.
Computer optimizati on of the AV-640 desi gn yiel ds the most efficient 3/8
wavelength el ectri cal design wi th maxi mum gai n and l ow angle of radi ati on
for long distance communi cation. No traps are used to achi eve eight band
performance. T he AV-640 is resonant on 6, 10, 12, 15 and 17 meters with
individual 3/8 wavelength radiators. The center radiator resonates on 20, 30
and 40 meters using paral lel end loaded Teflon wire coils. Capaci ty hats on
these bands give wide 2:1 VSWR bandwidth and the antenna is kept to a
height of 26 feet by the l ow i nductance coi ls. There are no "tricks" or "mystery
resonances" used for i mpedance matching on any band. No l ong-wire radial s
or counterpoise ki ts are necessary for operation of the AV-640. The AV-640 i s
self contained for simple, convenient portable or fixed operation. Mechanical
constructi on of the AV-640 is designed for extreme l ight weight and high wi nd
survival. Aircraft grade 6063-T832 aluminum and high strength fiberglass are
used for the entire radiator. The trap-free design presents a very l ow wi nd
surface area. Bul ky tubing is not required to support unwieldy traps. T he
broad 2:1 VSWR bandwidth on all bands lessens l arge frequency shifts seen
in other antennas when the antenna is wet or iced.The AV-640 is covered by
our Hy-Gain Warranty and supported by our customer service team. We would
like to thank you for purchasing thi s product from us and ask that you l et us
know of any suggesti on you may have. With proper assembly, install ati on, and
maintenance, your AV-640 will provide years of fai thful servi ce. Theory of
Operation The AV-640 HF Multiband Vertical antenna consists of an end fed
radiator that is resonant i n the 6, 10, 12, 15, 17, 20, 30 and 40 meter
amateur frequency bands. Resonances on each band are the resul t of
impedance matching a 3/8 wavelength el ement with a broadband RF
transformer. T he characteristic impedance at the base of the 3/8 wavelength
radiator is in the order of a few hundred ohms. To match thi s impedance two
tools are employed. Fi rst a counterpoise of 72" spokes is mounted at the
AV-640 base. T he capaci tance from this ground plane helps lower the base
impedance. Second, a 4:1 toroidal transformer (voltage balun) steps the base
impedance down to 50 ohms. T his transformer uses (2) ferrite cores for hi gh
power capabi lity. Also, the windings are made of twisted pair wire to improve
coupling and reduce l oss. A second hi gh power transformer is configured as a
1:1 current bal un to help stop RF from travel ing back on the feedline shield.
The radi ator of the AV-640 is at DC ground potential for static drain. This i s
accompl ished by a radio frequency choke in The center radi ator of the
AV-640 supports 1/4 wavelength stubs for 6 , 10, 12 and 17 meters. T he stubs
are pl aced approximatel y one tenth of a wavelength (el ectri cally 1/8
wavelength) above the AV-640 base. At the top of each stub the i mpedance i s
very high at the frequency the stub i s tuned. T his high impedance stops,
(chokes) RF at this point creating a resonant 3/8 wavelength radiator. There i s
mi nimal l oss usi ng this method as compared to standard trap circuits. Also,
VSWR bandwidth is not restricted by the °Q" of trap components. On 15
meters, the center radiator is termi nated with a capaci ty hat to form a 3/8
wavelength radiator. No stub or coi l is used on 15 meters. For 20, 30 and 40
meters, a coil and capaci ty hat are used on each band to create a 3/8
wavelength radi ator. The coil s are mounted at the top of the center radi ator.
These three coil s are connected in parall el. Parallel connection separates
each band to allow indi vi dual band tuning and has l ess loss than does series
connecti on. Also, the AV-640 coils have signifi cantly l ess loss than a standard
trap because the AV-640 capaci ty hats exhibi t greater capacitance than a
typical trap, therefore, less inductance is required. AV-640 Specificati ons
VSWR at Resonance: Less than 1.5:1 at antenna typical Gain: 3 dBi nominal
Hei ght: 25 ft 10 in Weight: 22 lbs Horizontal Radiation Angle: 360 degrees
Vertical Radiation Angle: 16 degrees at 1/4 wavelength hi gh Wind Surface
Area: 2.5 sq ft Wi nd Survival: 80mph
HF Cushcraft Multiband Vertical Antenna. Thi s multi band verti cal design
provi des 8 band coverage encompassing the 6, 10, 12, 15, 17, 20, 30 and 40
meter bands. Cushcraft achieved a maj or breakthrough i n the development of
an HF multiband vertical antenna that has been specificall y designed for use
with a tuner and amplifi er. As a result, the antenna more accurately addresses
the needs of the contemporary ham shack. Multiband vertical antennas have
always been compli cated designs with components as likely to be damaged
by high l evel s of mismatched transmi t power as the rigs they are attached to.
Before the use of tuners became wi despread, the antenna was protected by
the same safety mechanisms that protected the rig. Now, the automati c power
reduction circuits of the past have actually become a second l ayer of
protecti ve ci rcuitry. Although the auto-tuner provides the ham wi th a more
versatile device as wel l as protecting the rig’s components, the antenna is
more vulnerabl e than ever. With the press of a button, very high loads can be
i mposed on the antenna. The result to the antenna can be catastrophi c
fail ure in some i nstances. The R8 is the first multi band vertical desi gned for
the rigors of contemporary operating conditions. Al though the antenna is best
operated within it’s 2.0:1 VSWR bandwidth,it can sustain a 3.0:1 VSWR
mismatch at full power for typical operati ng intervals. Now radio amateurs can
take full advantage of the versatil ity that a tuner used in conjunction with a
multiband HF verti cal antenna can give them. For high wind environments,
add the R8GK Guy ki t-three point non-conductive guy system. The R8
provi des 360 degree (omni) coverage on the horizon and a l ow radiation
angle in the vertical plane for a better DX.
GES08901207
HY-GAIN 5band vert.tower 10/15/20/40/80m ;max.2kW
PEP;h=16.2m ;120km/h
Ground mounted vertical antenna. Automatic band selecti on through a
unique stub decoupling system. Extendable to 160m band with the HY-GAIN
base l oading coil LC-160Q.
1 pc: 26 490 Kč
RoHS
LC-160Q BASE COIL FOR AV18HT
GES08901215
HY-GAIN 160m base loading coil for AV18HT (150W CW max.)
1 pc: 2 915 Kč
RoHS
MK-160A SET 160M FOR AV18HT
GES08901216
HY-GAIN 160m s et for AV18HT (1kW CW max.)
1 pc: 3 180 Kč
RoHS
AV-620 MULTIBAND VERTICAL
ANTENNA 6-BANDS 6-20M
GES08901209
HY-GAIN 6-band vertical 6/10/12/15/17/20m ; 3dBi; 1500WPEP; 7m ;
6kg; 125km /h
The HY-GAIN AV-620 vertical need no external radi als.
1 pc: 9 290 Kč
RoHS
1 pc: 11 980 Kč
RoHS
1 pc: 14 290 Kč
RoHS
AV-680 9-BAND HF VERTICAL
ANTENNA 80/40/30/20/17/15/12
/10/6M
GES08902224
HY-GAIN 9-Band vertical 6/10/12/15/17/20/30/40/80m; 1500W PEP;
8.1m; 12kg
Hy-Gain Multi-Band PATRIOT Vertical Antennas 9-band verti cal covers
80/40/30/20/17/15/12/10/6 Meters • No radi als • No traps • No ground • No
tuning • Handles 1500 Watts hy-gai n’s PATRIOT HF vertical antennas are the
best built, best performing and best pri ced multiband verticals on the market
today. Make ful l use of your sunspot cycle wi th PATRIOT’sl ow angle signal.
Instead of typical traps, hy-gai n’s resonators are placed in parallel not in
series. End loadi ng of the lower HF bands allows efficient operati on wi th a
manageable antenna height. Introducing the new Hy-Gain PATRIOT-PLUS
AV-680 with a fully tunable 3.5-4.0 MHz coverage! With the AV-680, you get
the same great tradi tional performance of the AV-640 on 6 through 40 Meters
plus top-to-bottom capabil ity on 80 and 75 Meters. It's a great way to j oin new
l ocal nets and roundtables, explore the 75-Meter DX window, or add exciting
digital frequencies to your operating repertoi re. Simply pi ck the band
segment you wish to use, set the 80/75 Meter resonator, and you're in
busi ness. • No ground orradial s needed -- Effective counterpoise repl aces
radial s, end fed with broadband matchi ng uni t. • Automatic bandswitching -Single coax cable feed, each band is i ndividual ly tunable, wide VSWR
bandwidth. • Sleek and low-profile -- Low wind surface area, small area
required for mounting, mounts easil y on decks, roofs and patios. • Bui lt-to-l ast
-- Hy-gain’sPatriot seri es antennas boast ahigh wind survi val due to i ts sleek,
but sturdy frame. T he matchi ng unit is made from all Tefl on insulated wire. •
Top Loading: Parall el resonators -- best vertical -el ement efficiency • Full
ground independence: No unsi ghtly wire add-on radi als • Top-to-bottom 3.5
to 4.0 MHz coverage: Pi n-poi nt fine-tuni ng accuracy for rock-bottom SWR on
any frequency you choose. • Single coax feed . . . and with 100% automati c
band selecti on! • Low profile: Most compact ground-i ndependent antenna
avail able! • Legal-li mi t 1500-Watt PEP: Power handling on SSB and CW*
Adding 75/80 Meter coverage without compromising the Patri ot's classi c
performance, ground independence, and tiny footpri nt was no smal l task. Yet,
the AV-680 si ze, weight, and wind l oading are nearly identical to the AV-640
with no unsightly radi al extensions, traps, or top heavy vertical structures to
render it less attractive or unsafe. Band selection remains full y automatic, all
components handle maximum legal power, and you won't need a tuner wi th
your soli d-state ri g. The AV-680's Expanded-Frequency MatchboxTM circuit
ensures low SWR readings on every band, along with an upgraded balun
desi gn that concentrates all of your power in the antenna where it belongs! If
space is a premium at your QTH and appearance matters, let Hy-Gai n open
the door to one of ham radio's most attracti ve and popular bands with the
new AV-680. T his is your best choi ce for unparal lel ed versati lity and band
coverage from 6-80 Meters!
1 pc: 14 575 Kč
RoHS
DX-77A MULTIBAND VERTICAL
ANTENNA 7-BANDS 10-40M
40M1L 1el. tunable element
GES08901211
HY-GAIN 7-band vertical 10/12/15/17/20/30/40m ;3dBi;1500W
PEP;8.8m;12kg
HF Monobanders
80M1LL 1el. DIPOLE
GES08901237
MSQUARE tunable el. 6.9-10MHz; 1el./14m ; E=83°; 1.75dBi;
F/S=15-20dBtyp; SWR=2.0max.; 11.5kg; 50Ohm
GES08901234
MSQUARE 3,5-3,565MHz / 3,75-3,82MHz; 1el./32m; 2.0dBi; 3kW;
50Ohm.; 38kg; 50Ohm
No external radial s needed.
1 pc: 11 990 Kč
RoHS
DX-88
GES08901212
HY-GAIN 8-Band vertical 10/12/15/17/20/30/40
/80m ;1500W;50Ohm;7.6m ;9kg
The 80M1L is a reduced si zed di pole with great versati lity. It has been
upgraded both mechanically and el ectri cally. When used as a rotatable
dipol e, i t wil l easily outperform all fixed wire di poles. It can al so be used as a
building block for future expansion to a 2 or 3 element beam antenna. T he
dipol e can also be separated in half and used as phased 1/4 wave verticals.
Element hal ves start with 3” diameter tubing and taper through 2”, 1-3/4”,
1-1/2”, 1-1/4”, 1”, 3/4” & 1/2” secti ons to the 3/8 tips. The 3” and 2” secti ons
are separated by a rugged fi bergl ass insul ator to allow for the li near loadi ng
(3/8” alumi num tubing). A solid 2” O.D. x 36” fiberglass rod, sl eeved to the 3”
elements, serves as the center insul ator. Thi s is the same element used i n our
80M2L and 80M3L Yagis. Let your imagination go wild. You may come up
with something real different! The linear loadi ng terminates above the boom
and out of the el ement pl ane to reduce inductive cancellation and provi de
element support. Tip droop is typically 3-4 feet and l ooks better than some 40
meter elements. The 3 kW, 1:1 balun and phone / CW power swi tching relay
are housed in a water proof fi bergl ass Hoffman enclosure all owi ng access for
maintenance and tuning at the center of the el ement. Rel ay switchi ng
requi res 12 VDC @ .15a suppl y. The system defaults to phone when not
energized.
T his simple antenna combi nes 15 years of design and fi eld experience wi th
CNC machi ned parts to become the worlds best rotatable, reduced size
dipole. Everything we have l earned about linear l oaded dipoles and
structural rel iabili ty has been designed into the 40M1L. We j ust stretched it a
bit and broad banded it to cover at least 250 kHz or more. We also have
added an option to make i t a di pole on 17 meters as well . The center
i nsulator is a sol id 1-1/4 i nch fiberglass rod. There is nothing here to weaken
or break from the effects of sun, wind or i ce loading. The linear l oading
elements have been lifted slightly above the main element to eliminate the
tension/compressi on problems of other designs. T he l inear l oading also l ifts
the whole element sli ghtly vi rtuall y el iminating droop. Newl y designed
shorting bars make assembly and adjustment easi er and qui cker. If desired,
optimizing i nside the 40 meter band is done with 1/2” tip adj ustment. A Husky
1:1 balun delivers all your transmit power to the antenna with no feedline
radiation or pickup. Si nce thi s IS the driven element from our other l oaded 40
meter beams, it can be used as a beam by simpl y adding more di poles. If you
can't rotate a l ong boom, consider the advantages of stacki ng di poles
vertically for more gain and l ow radiation angle. The possibili ties are
i ntriguing!!
1 pc: 18 990 Kč
RoHS
40M2L 2el. Yagi
GES08901238
MSQUARE 6.9-10MHz/150kHz; 2el./16m; 5.5dBi; F/B 13-15dB;
E=74°; SWRm ax=1.2; Boom 6m ; 31kg; 50Ohm
AskRoHS
80M2LLA 2el. Yagi
Radials needed (no shipped wi th DX-88). You may construct your own radial
system (see manual), or purchase the optional ground radi al kit GRK-88, or
the resonant roof radial ki t RRK-88 for roof mounting. For the 160m band the
optional KIT-160-88 i s available (for ground mounted i nstallation only).
GES08901235
MSQUARE 3,5-3,565MHz / 3,75-3,82MHz; 2el./32m; 6.0dBi; 3kW;
50Ohm.; 100kg; 50Ohm
1 pc: 9 795 Kč
RoHS
GRK-88 RADIAL SET FOR DX88
GES08901213
HY-GAIN Ground Radial System for DX88
1 pc: 2 690 Kč
RoHS
RRK-88 ROOF RADIAL SET FRO
DX88
GES08901219
HY-GAIN Roof Radial System for DX88
1 pc: 2 690 Kč
RoHS
KIT-160-88 SET FOR DX88
GES08901214
HY-GAIN 160m s et for DX88 (750W CW m ax.)
1 pc: 5 345 Kč
RoHS
HF + VHF Omnidirectional Verticals
VEC-896 MULTIBAND VERTICAL
ANTENNA 6-BANDS
GES08901540
VECTRONICS 6-band vertical 2/6/10/15/20/40m ;1500W
PEP;50Ohm ;10m ;8kg
The recently computer upgraded and improved 80M2L i s now even better,
both mechani cally and electrically. Gain is up by .6 dB over older versi ons
and efficiency is now over 95%! T his i s accompl ished by using l ow l oss 3/8”
aluminum tube for the linear l oading elements. Element halves start wi th 3”
diameter tubing and taper through 2”, 1-3/4”, 1- 1/2”, 1-1/4”, 1” and 3/4”, 1/2”
sections to the 3/8” tips. Machined saddle cl amps have replaced the U-bolts
previously used. A solid 2” O.D. Fiberglass rod, sleeved to the 3” elements,
serves as the center i nsulator. The new, highly efficient 3/8” tube l inear
loadi ng system i s supported above the boom and out of the element plane to
reduce inductive cancellation, provide element support, and mi nimize
excessive el ement droop. New, rugged l inear loading shorting bars now al low
easier assembl y and adj ustment. A weather proof fi bergl ass housi ng now
protects the 5 kW 1:1 balun, the relays for phone-CW switchi ng and the hi gh
Q (600+) CW band coi ls. These top quality components are now accessible
for frequency adj ustments in the 3.5 to 3.6 MHz section of the band. Relays
requi res 12 VDC at 0.3A supply. Look forward to outgunning even the best of
the 4 squares! Parts are avai lable for upgrading older 80M2’s.
1 pc: 41 565 Kč
RoHS
40M3L 3el.Yagi
GES08901239
MSQUARE 7.0-7.3MHz/150kHz; 3el./15.5m ; 6.6dBdi; F/B 23dBtyp.;
E=62°; SWR=1.3typ.; Boom 9m; 50kg
AskRoHS
80M3LLA 3el. Yagi
T he recently upgraded, computer optimized, linear loaded, 40M2L Yagi has
been designed to outperform and outl ast all the “others”. It is now stronger
mechanical ly and easier to assemble. Only the ti ps of each element are
different as all the l inear loading settings are the same for each element. The
shorting bars are now 2 piece, clamp type making sol id l ong lasting
connections. The boom secti ons have been reconfi gured to reduce shipping
cost. Now every 40ML element in our 40 meter line util izes i denti cal,
standardi zed components. T his makes upgrading easi er and tuning
adj ustments easy and consistant. T he elements are butt sleeved and then
j oined wi th a SOLID rod of fi bergl ass or aluminum as the center coupling.
Designed withstand conti nuous winds of 100 mph or just the constant
battering of hi gh wi nds, this antenna WILL frustrate Mother Nature! T he li near
l oaded 3/16” di ameter rods anchor at the center, 10” above the main
element. T his feature reduces inducti ve cancel lation, element stress and
droop. T he 3/4” square 11” support riser is now 1/8 wall, further increasi ng the
strength and lifeti me of the Yagi. T he Dri ven element is matched wi th an
effi ci ent hairpin and the the 3 kW conti nuous, 5 kW peak, :1 balun is supplied
with the antenna. Four tuning options are provi ded to allow peak
performance in your favorite part of the band. All hardware is stainless or
gal vani zed except the U-bolts and remember every M2 40ML Yagi i s also
avail able in our ruggedized, 125 mph “SURVIVOR” Series.
GES08901236
MSQUARE 3,5-3,565MHz / 3,75-3,82MHz; 3el./32m; 7.3dBi;
5-10kW; 29m; Boom 18m ; 150kg
1 pc: 4 990 Kč
Action
RoHS
MFJ-1798 MULTIBAND VERTICAL
ANTENNA 10-BANDS
GES08900516
MFJ 10-band vertical 2/6/10/12/15/17/20/30/40/80m; 1500WPEP;
50Ohm; 6m
The 80M3L Yagi is a computer refined and i mproved performer, both
mechanically and el ectri cally. A l ow loss hairpin match provides perfect 1:1
match capabi lity. El ement halves start wi th 3” o.d. 1/8” wall tubing and taper
through 2” sleeved, 1-3/4”, 1-1/2”, 1- 1/4”, 1”, 3/4”, 1//2” &3/8” tips. T he 3” and
2” sections are joined by a custom fiberglass insul ator to section each
element half for the linear loading (3/8 alum. tube). A soli d 2” O.D. Fiberglass
rod, sl eeved to fit insi de the 3” elements, serves as the center insul ator for
each el ement. The center boom section is 4-1/2" O.D. x 20' with nearly 1/4"
wal l thickness. T he two outer boom secti ons are 4" O.D. x 20' x 1/8” wal l. T he
new, highl y efficient 3/8” tube li near loadi ng terminates above the boom and
out of the el ement plane to reduce inductive cancel lation, provide element
support, and reduce excessive droop. The new, heavy duty 1:1, 5 KW balun ,
now housed i nside the phone / cw switch enclosure provides pl enty of power
handling margin. The standard phone / CW band switching relays and high Q
(over 600) coils are housed i n a fiberglass housing. The whole assembl y i s
now fiel d servi ceable and small frequency adjustments can be made in the
CW part of the band. On the air, you’ll find little or no competition for the
80M3L. Upgrade parts are avail able for ol der 80M3’s.
AskRoHS
High performance 10-band vertical antenna with low radi ati on angle with no
ground radial s. Just 20feet (6m) tal l. Full size radiators for 2m to 20m. Needs
70feet (21m) free space. Good for near ground and roof mounti ng.
1 pc: 7 990 Kč
Action
RoHS
T he 40M3L antenna i s available in the 40M3FS Survivor Series version (wind
up to 125MPH). The 40M3L is a li near l oaded 40 meter Yagi designed wi th
20 years of experience and listeni ng to customer’s needs. The result is a
powerful package of clean mechani cal desi gn, quality materials, and
outstandi ng performance that wi ll deli ver years of enjoyment on the 40 meter
band. Mechanicall y the elements are mounted between 1/2” thi ck, machined
alumi num clamp plates! The Dri ven element is split and insul ated with a
1-1/4 i nch solid fiberglass rod and fed with a weather sealed 1:1 bal un. All
elements use linear loading of 3/16" 6061-T6 alumi num rod to reduce
overall length, wind load, and turning radius. The l inear l oaded sections
anchor 10" above the element to reduce inducti ve cancellation (requiring
LESS loadi ng), reduce mechanical stress, and mi nimize element droop (in
the ai r the antenna is easily mistaken for a 15 or 20 meter Yagi!). Compare
performance, construction and durability.... Thi s is not just another 40 meter
Yagi!!
AskRoHS
40M4LLDD 4el. Yagi
GES08901240
MSQUARE 7.0-7.3MHz; 4el./15.4m; 7.5dBi; 22dB F/B; E=60°; Boom
13m; SWRtyp=1.2:1; 71kg
The recentl y upgraded, computer opti mi zed, l inear l oaded, dual driven
40M4LLDD gets the bandwidth and maintains performance across the band
like no other 40 meter Yagi. Thi s was a huge challenge requi ring the latest
techniques in computer optimizati on. Gain, Front to Back and VSWR are
maintai ned nearly fl at across the whol e band! In additi on, it is now better
mechanically and easi er to assemble. Only the tips of each element are
different as al l the linear loading setti ngs are the same for each element. T he
shorting bars are now 2 piece, clamp type making solid long l asti ng
connecti ons. For forei gn amateurs, two tuni ng options are avail able; FULL
BAND and LOW END ACCENT UAT ED, but sti ll broadband. The resulti ng
design is head and shoulders above the competi tion in strength, durabili ty
and performance. This antenna has been designed to meet your crossband
SSB contesti ng needs and gi ve you years of enj oyment on the 40 meter band
regardless of future band pl an changes. Mechanically, the elements are butt
sleeved to withstand continuous winds of 100 mph or the constant batteri ng of
high winds . This antenna WILL frustrate Mother Nature! The Dri ven elements
are split i n the center and insulated with a sol id 1-1/4” fiberglass rod. T he
parasi tic element also have soli d 1-1/4” center alumi num center section. T he
3 kW conti nuous, 5 kW peak, 1:1 balun compl etes the package. All hardware
is stai nless or galvanized except the U-bolts. Options include parts to add 4
elements for 17 or 20 meters.
LJ-204BA
GES08901230
HY-GAIN Long John 14/18MHz 4el Monob.; 6.0dBd; F/B=20dB; 1kW
AM; l=7.9m ; 23kg
1 pc: 14 310 Kč
RoHS
LJ-205CA
GES08901231
HY-GAIN Long John 14/18MHz 5el Monob.; 6.5dBd; F/B=25dB;
1kWAM; l=10.4m; 28kg
17M3DX 3el. Yagi
Not a compromise or makeshift redesign, the 17M3DX is computer opti mi zed
from the ground up for gain and pattern on 17 meters. T he broadband 1:1
Teflon Coax Balun and low loss hairpin match maintai ns hi gh efficiency.
Element ri ng clamps, and other important components are CNC machined for
maxi mum strength and electrical integri ty. T he 84” boom sections are 2” O.D.
x .065” wall 6063-T 832 drawn al uminum tubing. All hardware is stainless
steel except the U-bolts. All elements are DC grounded. T he 17 Meters is
open despite the sunspot null and offers very good DX in a less competi tive
atmosphere. Expl ore this opportunity with the 17M3DX It deli vers very
respectable performance on a boom length that most towers and rotators can
handl e.
1 pc: 20 395 Kč
RoHS
20M4DX 4el. Yagi
GES08901242
MSQUARE 14-14.35MHz; 4el./10.6m; 7.3dBd; 23dB F/B; E=58°
H=75°; Boom=10.5m ; SWRtyp=1.1; 18kg
GES08901245
MSQUARE 18.05-18,2MHz; 3el./8.3m; 14,3dBi; 20db F/B; E=60°
H=90°; Boom 5,8m; SWR= 1; 15kg
1 pc: 20 390 Kč
RoHS
17M5DX 5el. Yagi
GES08901246
MSQUARE 18.08-18.18MHz; 5el./8.2m; 16.3dBi; 24db F/B; E=50°
H=64°; 5el; Boom 11m; SWRmax 1.2; 19kg
AskRoHS
30M3L 3el. Yagi
GES08901241
MSQUARE 10,1-10,15MHz ; 3el/15.5m ; 4.4dBi; 20dB F/B; 50Ohm ;
CSV<=1,2; Boom=9m; 63kg; 50Ohm
The 20M4DX is the fi rst i n a NEW SERIES of mi d-si zed, UPS shi ppable HF
antennas for all bands from 20 meters to 10 meters. Computer desi gned and
VERIFIED with NEC, you wi ll soon see the GAIN and other characteristics
adverti sed in QST magazine. T hat shoul d separate the players real fast! A
very clean pattern makes it ideal for STACKING (3 dB OF STACKED GAIN!).
We now spec FRONT TO REAR whi ch defines the pattern from 90 to 270
degrees. On your request we can suppl y E and H patterns in free space or
over ground. Careful, computer aided mechani cal desi gn for LOW WIND
AREA, yet long term el ectri cal and mechanical integrity are assured with CNC
machined element-to-boom ring clamps and other key components. T he
Teflon coax 1:1 balun and rugged, low loss hai rpi n match insure al l you
power gets to the airwaves! With a little thought, you WILL choose M2.
Contact us for pricing.
Thi s antenna real ly l ights up band! Sun spots up or down: who cares. Day or
night 10 MHz is al ways open somewhere! T he 30M3 lets you have all the fun
you deserve. And because of it’s 100 mph rating you won’t lose any sleep on
those stormy nights. The 30M3 provides performance and durabi lity.
Physically, the Yagi is a medium spaced, managable 3 element of very
rugged construction. A pair of machined, 1/2“ thick aluminum boom-toelement plates secure each el ement with double cradle clamps to the 3“ x
.125“ wall boom. Elements taper i n si ze from 1-1/2“ to wind area reduci ng
3/8“ ti ps. Each inner secti on i s double walled at criti cal points to achi eve a
100 MPH wind survival rating. All hardware, except U-bolts, is stainless steel
1 pc: 28 790 Kč
RoHS
20M5LD 5el. Yagi
GES08901243
MSQUARE 14.0-14.35MHz; 5el./11m; 10.2dBi; 23dB F/B; E=50°
H=66°; Boom 13.6m ; SWRmax=1.5; 42kg
T he 17M5DX antenna i s available in the 17M5DX Survi vor Seri es (wind up to
125MPH). The 17M5DX i s a great performer for its size. It was designed for
l ow wind area but rugged and l ightweight and it wil l save you a bundle on
shipping. IT ’S UPSABLE! l ike all our “DX” series. The computer opti mi zed
desi gn al lows full band coverage with good gai n and front to back.
Performance i s excellent on both the CW and phone! Mechanicall y, CNC
machined al uminum (6061-T6) ring cl amps ground the elements to the boom
and make assembly a snap. The central boom secti ons are 2-1/2” O.D. x .058”
wall 6063-T832 alumi num tubing with 2” O.D. ti ps. An overhead guy system
i s suppl ied. A hairpin type match coupl es the 3 kW 1: balun to the feed line.
T he antenna is completely DC grounded. T he 17M5DX i s also great for
stacking, providing 3 dB increased gain not to mention the lower angl e of
radiation. The 17M5DX is a perfect stacking partner for our other “DX series
Yagis like the 20M4DX, 12M4DX, and 10M4DX. Put the 17M5DX to the test
i n any conditions and see what good design can do for you!
AskRoHS
LJ-153BA
GES08901227
HY-GAIN Long John 21MHz 3el Monobander; 5.3dBd; F/B=25dB;
1kW AM; l=3.7m ; 10kg
AskRoHS
10-15M1DX Singlle Band Rotatable
Dipole
GES08902212
1 pc: 6 095 Kč
RoHS
LJ-155CA
MSQUARE 20-30MHz; 1el./max. 7.6m; 2,14dBi; Beamwidth 90¨;
SWRmax.=2:1; Pmax=3kW; 3kg
GES08901228
HY-GAIN Long John 21MHz 5el Monobander; 7.6dBd;
F/B=25dBmax; 1kW AM; l=7.9m
The 20M5 antenna i s avai lable in the 20M5 Survivor Seri es (wind up to
125MPH). The 20M5L (LITE) is BRAND NEW! It features the same on air
performance as it’s very popul ar, heavy wei ght brother, the 20M5, but i t i s
much l ighter weight. We l istened to our customers and have carefully reduced
it’s weight signifi cantly while reducing the wi nd survival rating by only 10
MPH. T he 20M5L has the same clean pattern and great gain across the
band. We have also made it a “di rect feed” Yagi requiring no matching, only
a 1:1 balun. It i s easier and quicker to assemble as well as easier to i nstall.
Stacki ng a pair wi ll cost less and put less stress on your tower! Mechani cally; a
pair of machined, 3/8” x 4” aluminum boom-to-el ement plates and saddles
ground each parasitic element and keep el ements aligned perfectl y for years
to come. Elements taper in 1/4” steps from 1- 1/4” to the adjustable 1/2” tips.
The re-designed 44 foot x 3“ dia. boom is a full 1/8 in wall in the center
section but the tips are hal f the wei ght at 1/16” wall . Al l critical hardware i s
stai nless steel . The 20M5L is availabl e through our fi ne di stributors,
worldwide. For you 100 mph+ hi ll toppers, we make a SURVIVOR SERIES
sold factory di rect onl y! See our web site for more details on all our
outstanding products.
1 pc: 11 395 Kč
RoHS
15M4DX 4el.Yagi
GES08901247
MSQUARE 21.0-21.45MHz; 4el.; 15.5dBi; 24db F/B; E=52° H=70°;
4el; Boom 8.2m ; SWR<=1.2:1; 16kg
1 pc: 32 385 Kč
The 10-15M1DX is a si ngle-band dipole antenna designed wi th performance
and affordabili ty in mind without skimpi ng on quali ty. Originally designed by
radio pioneer Hei nri ch Hertz in 1886, the dipol e antenna was ori ginal ly
called the “Hertz” antenna. It stands the test of time as the basi s of most hi gh
performance antennas today. Built to the demanding specs of our “DX” series
yagi s, thi s antenna uses 6061-T6 alumi num tubi ng and 6061-T6 aluminum
machined hardware for its durable, l ightweight el ements. A soli d fiberglass
center i nsulator, machi ned aluminum mast mounting components and
stai nless steel hardware will keep this in the air for years. Versatility i s key for
thi s antenna—equal ly suited as a fixed or rotatabl e dipole. Li ghtweight and
low-profi le, it’s the perfect HF antenna for your QTH, whether you want a
simple, unobtrusive, no-compromise radiator on a tower or mast, or in a
stealthier appl icati on such as in an attic. “Uni-cradle” mounting all ows i t to
securely grip a wide range of masts. With element secti ons of 48 inches (122
cm) or less i n l ength, its light, simple and compact desi gn makes it an ideal
candidate for Fiel d Day, SOTA, DXpeditions and EMCOM use. It can easi ly
be confi gured and reconfi gured for any frequency from 20-30 MHz simply by
changi ng the tip length.
1 pc: 6 885 Kč
RoHS
LJ-203BA
GES08901229
HY-GAIN Long John 14MHz 3el Monobander; 5.0dBd; F/B=23dB;
1kW AM; l=5.1m; 15kg
1 pc: 8 745 Kč
RoHS
RoHS
20M6 6el. Yagi
GES08901244
MSQUARE 14.0-14.35MHz; 6el./11m; 16.6dBi; 25dB F/B; E=46°
H=60°; Boom=18m; SWRmax=1.2; 83kg
T he 15M4DX is a great performer for its si ze. It was designed for low wind
area but rugged and lightwei ght and it will save you a bundle on shipping.
IT’S UPSABLE! like all our “DX” series. The computer opti mi zed design
allows full band coverage wi th good gain and front to back. Performance is
excellent on both the CW and phone. Mechani cally, CNC machined
alumi num (6061-T 6) ri ng clamps ground the elements to the boom and make
assembly a snap. A hairpin type match coupl es the 3 kW 1: balun to the feed
l ine. T he antenna is completel y DC grounded. T he 15M4DX is al so great for
stacking, providing 3 dB increased gain not to mention the lower angl e of
radiation. The 15M4DX is a perfect stacking partner for our other “DX series
Yagis like the 20M4DX and 10M4DX. Put the 15M4DX to work in the new
cycle!
1 pc: 23 990 Kč
RoHS
The 20M6 antenna i s avai lable in the 20M6 Survivor Seri es (wind up to
125MPH). The 20M6 is a medium spaced, high performance, full band
coverage 6 element Yagi, computer opti mi zed to squeeze the last drop of
performance from this boom l ength. The design provides virtually fl at gain,
exceptional front to back and excel lent VSWR never exceeding 2:1 at the
upper band edge. Large, sleeved el ements and boom provide the 100 mph
wind survival factor. Construction i ncludes machined boom to element
mounting plates and a rugged, efficient hairpin match. Predri lled holes for
the stainless bolts and locknuts will keep you on the top of the pileup for years
to come in spite of Mother Nature! T he 20M6 is our “top of the li ne” 20 meter
Yagi. A 125 mph versi on of thi s design i s also availabl e i n our “Survivor
Series“
AskRoHS
15M6DX 6el.Yagi
GES08901248
10M7DX 7el.Yagi
GES08901251
6M5XHP
GES08901254
MSQUARE 21.0-21.45MHz; 9.4dBd; 25db F/B; E=48° H=53°; 6el;
Boom 13.5m; SWR<=1.5:1; 25kg
MSQUARE 28-28.75MHz; 7el./5.6m; 12.4dBi; 25db F/B; E=43°
H=50°; Boom 13.6m ; SWR<=1.4:1; 25kg
MSQUARE 50-50.5MHz; 11.54dBi; E42° H52°; 21dB F/B; CSV 1.2
typ; Boom 5,5m; 6kg; 50 Ohm SO239
The 15M6 antenna i s avai lable in the 15M6 Survivor Seri es (wind up to
125MPH). T he 15M6DX design joi ns our quali ty series of SUPER GAIN Yagi s
made possible by careful computer optimization. Full band coverage,
combined with excellent overall VSWR, allows total frequency agi lity while
maintai ning excel lent gai n and pattern. It is also ideal for stacking.
Mechanically, the 15M6DX features our CNC machined aluminum elementtoboom ring clamps whi ch ground all the el ements for static and lighti ng
protection. Elements are sleeved and double bolted to each clamp with
stai nless hardware. A rugged and versatile hairpin match and high power 1:1
coaxial bal un keep the effi ci ency high. All hardware i s stainl ess steel except
the U-bolts. The 15M6DX Yagi is designed to be a trouble free, DX pileup
topper for years to come.
The 10M7 antenna i s avai lable in the 10M7 Survivor Seri es (wind up to
125MPH). T he 10M7DX was designed for the DX’er using computer
optimization techniques. Performance is excel lent on both the CW and
phone. The pattern is sharp and clean reducing noise and QRM. T he
10M7DX i s a band opener and closer. It makes 100 watts sound like a kW!
Mechanically, CNC machined aluminum (6061-T6) ring clamps ground the
elements to the boom and make assembly a snap. A hairpin type match
couples the 3 kW 1: bal un to the feed line. The antenna is completely DC
grounded. Great effort has been put into making sure this antenna stays i n the
air for years to come while providing enjoyment and satisfaction al ong the
way. The 10M7DX i s destined for the DX antenna HONOR ROLL!
SPECIFICATIONS Model 6M5XHP Frequency range 50-50.5 MHz Gai n 11.54
dBi Front to back, Typical 21 dB Beamwi dth E=42° / H=52° Recommended
Stacking 15-21' High 19-23' Wide Feed impedance 50 Ohms / SO-239
unbal anced VSWR 1.2:1 @ 50.1 MHz typical Power Handling 1.5 KW Match
Type Hai rpi n Match Li ghtening Protection All El ements Grounded Boom
l ength 1216" (549cm) Max. Elem. Lenght 113" (287cm) Turning Radi us 134"
(341cm) Mast Size 1-1/2 to 2" nom. Wind Area / Survi val 2.2 sq. ft. / 100 MPH
(0,22m2 / 180km/hod) Weight / Shi pWt. 12 lbs / 14 lbs (6kg / 7kg) FEATURES:
T he 6M5XHP is the latest computer opti mi zed version of our popular 6M5X.
T he 6M5XHP has been re-designed to use a hairpin type direct feed. We j ust
made a good thing better, maintaining a low wind load and great
performance for its size. The 6M5XHP wil l compliment the rest of your
antenna system and not overload your tower. T he 6M5XHP is perfect for the
Ham trying 6 meters for the first time or the seasoned vet who may stack them
for lower angle of radi ati on or even some EME use.
AskRoHS
6M3-SS
AskRoHS
12M4DX 4el.Yagi
GES08901249
MSQUARE 24.89-24.99MHz; 4el./6.4m ; 10.7dBi; 20db F/B; E=48°
H=58; Boom 8.2m ; SWR<=1.2:1; 14kg
GES08902037
MSQUARE 50-50.6MHz; 8.1dBi; E64°,H96°; 28dB F/B; CSV1.5 typ;
Boom 1,8m ; 2kg; 500W; 50Ohm
1 pc: 11 985 Kč
RoHS
6M7JHV
GES08901256
MSQUARE 50.0-50.4MHz; 13.0dBi; E40° H42°; 25dB F/B; SWR 1.2
typ; Boom 9,5m; 9,5kg; 50Ohm
The 12M4DX antenna is availabl e i n the 12M4DX Survivor Series (wind up to
125MPH). T he 12M4DX is a great performer for its size. It was designed for
low wi nd area but rugged and lightweight and it wi ll save you a bundl e on
shippi ng. IT’S UPSABLE! like al l our “DX” series. T he computer optimized
design allows full band coverage with good gain and front to back.
Performance is excell ent on both the CW and phone. Mechanical ly, CNC
machined aluminum (6061-T6) ri ng clamps ground the elements to the boom
and make assembly a snap. A hairpin type match couples the 3 kW 1: bal un
to the feed li ne. The antenna is completely DC grounded. The 12M4DX i s
also great for stacking, provi ding 3 dB increased gain not to mention the
lower angl e of radiation. The 12M4DX is a perfect stacking partner for our
other “DX seri es Yagis li ke the 20M4DX and 10M4DX. Put the 12M4DX to the
test in the new cycle!
1 pc: 23 590 Kč
RoHS
LJ-103BA
GES08901225
HY-GAIN Long John 28MHz 3el Monobander; 5.3dBd; F/B=24dB;
1kW AM; l=2.5m; 7kg
1 pc: 4 770 Kč
RoHS
LJ-105CA
GES08901226
HY-GAIN Long John 28MHz 5el Monobander; 8.6dBd;
F/B=36dBmax; 1kW AM; l=7.4m
Model 6M3-SS Frequency Range 50.0 To 54.0 MHz Tunable Gai n 8.1 dBi
Front to Back 28 dB Typical Beam Width E=64° H=96° Feed Type Gamma
Match Feed Impedance 50 Ohms Unbal anced Max VSWR 1.5:1 Input
Connector SO-239 Boom Length / Dia 5’ 8“ / 1“ Max El ement Length / Dia
77-3/8“ Turning Radius 5’ 5“ Stacking Distance 14’ High & 18’ Wi de Mast Size
1-1/2“ to 2“ Nom. Wind area / Survival 0.7Sq. Ft. / 75 MPH Weight / Ship Wt 4
Lbs. / 5 Lbs. # of El ements 3 FEAT URES: New licensed Hams wi ll find the
6M-3SS a low cost, medium performance antenna to be a great choice for a
starter antenna without compromisi ng quality. A singl e heavy duty mounti ng
cradle and stai nless steel hardware, gi ve you the confidence of quali ty
constructi on you have come to expect from M2. Built with size and portabili ty
in mind, this antenna is great for Field Days, Mountain Topping, Fox Hunts
and DXpediti on use. T he antenna breaks down to no more than 40“ long,
making i t a natural for trips.
1 pc: 5 090 Kč
RoHS
6M3
GES08901253
MSQUARE 50-50.6MHz; 8.2dBi; E64°,H90°; 20dB F/B; CSV 1.1 typ;
Boom 2,1m ; 3kg; 50Ohm
Model 6M7JHV Frequency Range 50.0 To 50.4 MHz Gain 13.0 dBi Front to
Back 25 dB Typical Beam Width E=40° H=42° Feed Type “T“ Match Feed
Impedance 50 Ohms Unbalanced Max VSWR 1.2:1 Typi cal Input Connector
“N“ Female Boom Length / Di a 30’ 8“ / 1-1/2“ Max Element Length / Dia 9’ 6“
T urning Radius 17’ 2“ Stacki ng Distance 25’ High & 27’ Wide Mast Size 1-1/2“
to 2“ Nom. Wind area / Survival 2.5 Sq. Ft. / 85 MPH Weight / Ship Wt 19
Lbs. / 21 Lbs. FEATURES: The 6M7JHV is a mid-sized 7 element antenna
desi gned origi nally for the l ate Dave Batcho, N5JHV. The JHV’s excellent
gai n is coupled wi th a very clean pattern for reducing local noise, making it
i deal for longhaul terrestrial and EME communicati ons. An outstanding
performer by itself, the JHV also produces 17 dBd in an 4-bay array.
Mechanical features i nclude machined al uminum el ement-mounting blocks,
O-ring seal ed connectors and bal un, sil icone-gel sealed T- match block, and
stainless steel hardware. Elements are 3/8 tube and DC grounded. The 1-1/2“
boom breaks down i nto 5 ft sections for easy portabi lity. An overhead guy
system provi des additi onal boom support. It has become the standard of
choice for HF/50 mHz DXpedi tions.
1 pc: 12 750 Kč
RoHS
6M9KHWA
GES08901258
MSQUARE 50.0-50.4MHz; 14.8dBi; E34° H39°; 23dB F/B; SWR1.2
typ; Boom 15m; 24.5kg
1 pc: 7 685 Kč
RoHS
10M4DX 4el. Yagi
GES08901250
MSQUARE 28.0-28.8MHz; 4el./5.6m; 10.1dBi; 22db F/B; E=53°
H=68°; Boom 7.2m; SWR<=1.2:1; 19kg
The 10M4DX was designed for high performance while keeping weight, wi nd
area and costs low. Using computer optimizati on techniques, we have
squeezed for excell ent performance on both the CW and phone. T he
10M4DX is a great antenna to stack with more 10M4DX Yagis or wi th other HF
antennas. Mechanically, CNC machi ned aluminum (6061-T6) ring clamps
ground the elements to the boom and make assembl y a snap. A hairpin type
match couples the 3 kW 1: balun to the feed line. The antenna is completely
DC grounded. Great effort has been put into making sure thi s antenna stays in
the ai r for years to come whil e providing enjoyment and satisfaction along
the way.
1 pc: 21 390 Kč
RoHS
Model 6M3 Frequency Range 50.0 To 50.6 MHz 51.0 To 54.0 MHz Gain 8.2
dBi Front to Back 20 dB Typical Beam Width E=64° H=90° Feed Type “T“
Match Feed Impedance 50 Ohms Unbal anced Max VSWR 1:1 @ 50.75 MHz
Input Connector SO-239 Boom Length / Dia 6’ 9“ / 1-1/2“ Max Element
Length / Dia 9’ 8“ T urning Radi us 6’ 3“ Stacking Distance 14’ High & 18’ Wi de
Mast Size 1-1/2“ to 2“ Nom. Wind area / Survival 1.2 Sq. Ft. / 100 MPH
Weight / Shi p Wt 6 Lbs. / 7 Lbs. FEATURES: The 6M3 is a light but rugged
computer opti mi zed Yagi offering low wind load and great performance for its
size. It will compliment the rest of your antennas and tower system. Quick and
easy to assembl e, i t is also great for mountain toppi ng, grid expeditions and
DXpeditions. The 6M3 features the same machined aluminum mounti ng
blocks and sealed ’T’ match block that its big brothers use. The 6M3 is perfect
for the ham trying 6 meters for the first time or the the seasoned vet who may
stack them for improved gain. For the seri ous 6 meter enthusiast, it provi des
and effective, i nexpensive bui ldi ng bl ock for vertical stacks and
MOONBOUNCE arrays. A tuning chart is included for the FM band.
1 pc: 5 865 Kč
RoHS
SPECIFICATIONS Model 6M9KHWA Frequency range 50.0 - 50.4 MHz Gain
over a di pole 14.8 dBi Front to back, Typical >23 dB Beamwi dth, degrees
E=34° / H=39° First sidel obe -18 dB Stacking (Horiz Pol )) 30' W, 27' H VSWR
1.2:1 Input Connector 'N' Femal e Power Handl ing 1500 Watts Element Type
3/8 x .049" Tubi ng Boom Length/dia /support 49' 4" / 1-1/2, 2 & 2-1/2" /
Dacron Wind Area / Survival 4.3 SQ. FT. / 100 MPH (0,43m2 / 180km/hod.)
T urning Radius 27.7" Weight / Shi pWt. 49 / 52 LBS FEATURES Thi s antenna
was inspired by Ray Grenier, K9KHW. Countl ess hours of computer
optimizati on, range confi rmati on and on the air testing have resul ted in a
trul y remarkable antenna. The 6M9KHW is capable of produci ng moon
echoes when pointed at rising or setting moon and running the l egal power
l imit. If you can hear your own moon echoes over a one half mi llion mi le
path, just thi nk what it could do for your signal on long haul tropo, meteor
scatter or just an ordinary E or F2 opening. And for the adventurous, imagine
what four would do. The 6M9KHWA boom center secti ons are 2.5“ dia. & the
rest of the sections all telescope in 1/2“ or 1/4“ increments. It wil l survive
horrible condi tions (100 MPH). This antenna is fed wi th a new hairpin design
to optimize VSWR and new 1:1 bal un, desi gned more rugged than the
previ ous feed. Rugged 1/2“ X 40“ element center secti ons and 3/8“ dia. tips
mounted on machined, “slip on“ element to boom clamps guarantees this
antenna wil l stay up for years to come.
1 pc: 26 490 Kč
RoHS
TH-3JRS
HF Multibanders
KT34M2 HF MULTIBANDER
GES08901284
HY-GAIN Tri-Bander 3el.;10/15/20m;5.8dBd;F/B=25dB;600WPEP;
l=3.7m;12kg
7&10-30LP8 LOGPER ANTENNA
GES08901293
MSQUARE Tribander 14/21/28MHz; 6.5-7.6dBi; 17-25dB F/B; 4el.;
SWRtyp 1.5:1; 22kg; 50Ohm. SO239
The M2 KT34M2 i s now the best and strongest short tri bander avai lable
today. All four el ements are resonant on each band. A dual driven element
all ows a beauti ful flat match, broad gain, and high front to back curves across
10, 15 and 20M. A 3kW 4:1 bal un efficiently matches the antenna to 50
Ohms. All sheet metal parts have been upgraded to our new machined
shorting bars, sti ffening and strengthening the antenna noti ceably. The long
term performance is enhanced by the total contact machi ned j oints. Thi s
antenna wil l be competitive wi th most monobanders ! Be surprised, get the
NEW KT 34M2.
1 pc: 10 070 Kč
RoHS
TH-3MK4
GES08901285
HY-GAIN Tri-Bander 3el.;10/15/20m;5.8dBd;F/B=25dB;1.5kWPEP;
l=4.3m;16kg
T he 7&10-30LP8 antenna is availabl e in the 7&10-30LP8 125MPH Survivor
Seri es (wind up to 125MPH).
1 pc: 69 890 Kč
RoHS
RoHS
GES08901294
10-30LP8 LOGPER ANTENNA
MSQUARE HF Multibander 14&21&28MHz; Gain 9.1-10.5dBi;
17-29 dB F/B; 6el.; SWRtyp 1.5:1; 38kg
GES08901297
MSQUARE 10-30MHz; 6dBd; 15dB F/B; E=65°; 8el; Boom 7.1m;
SWR typ 1.5:1; 180km/h; 43kg
1 pc: 13 250 Kč
1 pc: 59 925 Kč
RoHS
RoHS
KT34A TO KT34M2 Upgrade Kit
(2578)
GES08901296
MSQUARE 7&10-30MHz; G=3-6dBd; 6-15dB F/B; E65° H75°; 8el;
Boom 9m; SWR 1.8:1; 55kg
1 pc: 41 990 Kč
KT36XA TRIBAND YAGI
HF Log-Periodic Antennas
GES08902205
KT34A TO KT34M2 Upgrade Kit (2578) KLM to M2 4 Element
TH-5MK2
GES08901286
HY-GAIN Tri-Bander 5el;10/15/20m;7.8dBi;F/B=19-25B;1,5kWPEP;
l=6m ;29kg
T he 10-30LP8 antenna i s availabl e in the 10-30LP8 125MPH Survi vor Series
(wind up to 125MPH).
1 pc: 60 990 Kč
RoHS
10-30LP8-125 LOGPER ANTENNA
SURVIVOR SERIES
Model KT34A TO KT34M2 UPGRADE KIT Frequency Range 14-14.35 MHz
21-21.45 MHz 28-29 MHz Max VSWR <1.5:1 Input Connector SO-239 Weight
/ Ship Wt 14 Lbs. / 16 Lbs. FEAT URES: The M2 KT 34(A)-KT34M2 UPGRADE
KIT provides all the parts to bring up your ol d KT34(A) to current ‘34M2
speci fications and keep it that way. Over the years i t has become evident that
the original sheet metal straps loosen wi th time and the connections becomes
intermittent and / or lossy. The new close tol erance, CNC machined shorti ng
BARS produce solid, low loss connecti ons for years. The machi ned bars also
add mechanical sti ffness to the element. In addition, all new hardware has
been suppl ied as well as new UV stabilized Capacitor Caps and tubes needed
for the new ‘T‘ match. Why not upgrade today and see what M2 can do for
you.
GES08902156
MSQUARE 10-30MHz; 6dBd; 15dB F/B; E=65°; 8el; Boom 7.1m;
SWR typ 1.5:1; 225km/h
Survivor Series construction for wind up to 125MPH.
1 pc: 20 935 Kč
RoHS
TH-7DX
GES08901287
HY-GAIN 7el 10/15/20m;8,0-9,6dBi;F/B=18-22dB;4kWPEP;
7,3m ;34kg;160km/h
Ask
LP-1010AN LOGPER ANTENNA
GES08901277
HY-GAIN Log-Per 14el; 10-30MHz; 7dBi; F/B=17dB; 1.5kW PEP;
l=8.5m; 43kg
AskRoHS
EXP-14
GES08901281
HY-GAIN Tri-Bander 4el; 10/15/20m; 8.1dBi; F/B=21-27dB;1,5kW
AM; l=4.2m ; 21kg
1 pc: 23 850 Kč
Version wi th N-female connector
RoHS
TH-11DX
GES08901278
HY-GAIN 11el 10/12/15/17/20m;7,5-9,2dBi;F/B=19-27dB;4kWPEP;
7,3m ;40kg
AskRoHS
LP-1009AN LOGPER ANTENNA
1 pc: 16 695 Kč
RoHS
QK-710
GES08901282
HY-GAIN 30/40M Kit for EXP-14
1 pc: 4 770 Kč
TH-2MK3
GES08901283
HY-GAIN Tri-Bander 2el.;10/15/20m;3dBd;F/B=15-20dB;1,5kWPEP;
l=2m ;10kg
1 pc: 31 790 Kč
Version wi th N-female connector.
RoHS
AskRoHS
1 pc: 10 335 Kč
RoHS
GES08901275
HY-GAIN Log-Per 12el; 13-30MHz; 7.2-13.2dBi; F/B=10-22dB;
4kWPEP; l=9m; 43kg
CLP5130-1N LOGPER ANTENNA
50-1300MHz
2M7 7el. Yagi
GES08901708
CREATE 21el.log-per antenna 50-1300MHz; Gain 10-12dBi; F/B
10-15dB; SWRm ax.2:1, Nfem ale
VHF Base and Repeater Verticals
EB-144/RK-2M
GES08901334
MSQUARE 144-148MHz; 7el.; 12.3dBi; E43° H50°; 20dBF/B;
SWR1.3typ; Boom 2,5m; 2kg; 50Ohm
GES08901321
MSQUARE 144-146(135-150)MHz; SWR1.2:1; Om ni; 50Ohm; 1kW;
160km/h; H87cm,W72cm
Log-per antenna, boom lenght 2.0m, el ement lenght 3.0m, for H and V
polarisation, impedance 50 Ohm, max. 500W PEP, for mast si ze 48-61mm,
wei ght 5kg, max. wind speed 40m/sec., recommended rotator CREATE RC5-1
or RC5-3 seri es.
1 pc: 7 995 Kč
RoHS
CLP5130-2N LOGPER ANTENNA
105-1300MHz
GES08901709
Del ivered with base RK-2M.
1 pc: 6 590 Kč
CREATE 17el.log-per antenna 105-1300MHz; Gain 11-13dBi;
F/B10-15dB; SWRmax 2:1, Nfemale
RoHS
MFJ-1516 BASE REPEATER
ANTENNA
GES08901315
PulsarTM Base/Repeater Antenna 144MHz, length 4.5m , 200W,
SO-239
Model 2M7 Frequency Range 144 To 148 MHz Gain 12.3 dBi Front to Back
20 dB Typical Beam Width E=43° H=50° Feed Type “T “ Match Feed
Impedance 50 Ohms Unbalanced Max VSWR 1.2:1 Typi cal Input Connector
“N“ Female Boom Length / Dia 8’ 10“ / 1“ Max Element Length / Dia 40-1/2“
T urning Radi us 63-1/2“ Stacking Distance 6’ 8“ High & 7’ 3“ Wide Mast Size
1-1/2“ to 2“ Nom. Wind area / Survival 0.50 Sq. Ft. / 100 MPH Wei ght / Ship
Wt 3 Lbs. / 4 Lbs. FEATURES: T he 2M7 is a computer optimized yagi that
will outperform longer old design antennas. The 2M7 covers the whol e band
with onl y slight performance degradation at the band edges. Side lobes are
very l ow and i t is perfect for stacking 2 or more. Its light weight and durability
make it great for portable hill topping. The 2M7 i s buil t for long term
electrical and mechanical integrity. T he CNC machined “T “ Match Block
features Oring sealed connectors and is internally sealed with a space-age
si licone gel with nearly 4 ti mes the di electric strength of air. Elements are
6061-T6 3/16“ aluminum rod, mounted through the boom on UV stabili zed
button insulators. Al l hardware is stainless steel except U-bolts. Other key
electrical and mechanical parts are CNC machi ned for accuracy and
durability.
1 pc: 2 990 Kč
Action
RoHS
2M9FM 9el. Yagi
GES08901335
MSQUARE 145-148MHz; 9el.; 14,1dBi; E35°,H38°; 24dB F/B;
SWR1.4typ; Boom 4,5m; 3kg; 50Ohm
Log-per antenna, boom lenght 1.4m, el ement lenght 1.3m, for H and V
polarisation, impedance 50 Ohm, max. 500W PEP, for mast si ze 42-50mm,
wei ght 3kg, max. wind speed 40m/sec., recommended rotator CREATE RC5-1
or RC5-3 seri es.
1 pc: 5 495 Kč
RoHS
1 pc: 2 650 Kč
RoHS
VHF Mobile Car Antennas and Magnet
Mounts
MFJ-1412 Mobile Antenna 102cm
for 2m band
MFJ-1750 GP GP ANTENNA
5/8LAMBDA 2M
GES08900481
MFJ 5/8 wave Ground Plane 2-Meter Antenna
GES08901299
RuffRiderTM 40" 2M Mobile. Not approved in the Czech Republic.
Easy i nstallation to any 25 -38mm mast, with SO-239 connector
1 pc: 930 Kč
RoHS
MFJ-1754 DUAL BAND BASE
ANTENNA 2M/70CM
GES08900483
MFJ Dual Band Bas e Antenna for 144 / 440 MHz Band
1 pc: 795 Kč
1 pc: 1 055 Kč
RoHS
MFJ-1438
Easy i nstallation to any 25 -38mm mast, with SO-239 connector , stainless
radiator 49cm (19") long (lambda/4 for 2m) has a buillt-in integral phasi ng
coil for 70cm
GES08901302
RoHS
RuffRider, quad 10/6/2/440 m obile. Not approved in the Czech
Republic.
1 pc: 6 890 Kč
RoHS
VHF Beams
2M4 4el. Yagi
2M9SSB 9el. Yagi
GES08901333
MSQUARE 144-148MHz; 4el.; 9.6dBi; E54° H74°; 20dBF/B;
SWR1.5m ax; Boom1,2m; 1,5kg; 50Ohm
1 pc: 2 650 Kč
RoHS
Model 2M9FM/2M9SSB Frequency Range 144 To 146 MHz Gain 14.1 dBi
Front to Back 20 dB Typi cal Beam Width E=35° H=38° Feed Type “T “ Match
Feed Impedance 50 Ohms Unbal anced Max VSWR 1.2:1 Typical Input
Connector “N“ Female Boom Length / Dia 14’ 6“ / 1“ To 3/4“ Max Element
Length / Di a 40-5/8“ Turning Radius 8’ Stacking Distance 9’ 6“ High & 10’
Wide Mast Si ze 1-1/2“ to 2“ Nom. Wi nd area / Survi val 1.2 Sq. Ft. / 100 MPH
Weight / Ship Wt 5 Lbs. / 7 Lbs. FEATURES: Up to the mi nute design usi ng a
state-of-the-art computer optimizati on program to deliver the most gai n for
boom l ength of any antenna on the market. Each model’s performance is
optimized for a specifi c mode and frequency range, with no compromises to
achieve unneeded bandwi dth: the 2M9SSB covers 144-146 MHz and the
2M9FM covers 145-148 MHz. Where do you want to make yoursel f heard?
Both models are ideal building blocks for a small turning radius, high-gain
stacked array. Two horizontally polarized, vertical ly stacked 2M9SSB’s yield
the same gain (14.8 dBd) as M2’s 33 ft 2M5WL, but with about 1/2 the turning
radius (8’ - great for QTH’s that won’t permit a l ong boom Yagi). The 2M9FM
can be stacked on a crossboom for the same gain increases, and the turning
radius is sti ll a very manageable 10 ft. The heart of these antennas i s a dri ven
element module originall y desi gned for mariti me AT S satell ite service. All
connectors are O-ring sealed to the CNC machi ned block. Internal
connections are sealed wi th a space-age sil icone gel with nearly 4 times the
dielectric strength of air. The balun connectors are tri ple seal ed on the coax
and nut-seal ed at the block connectors. The type “N“ feed connector uses a
gol d-plated, beryl lium copper center pi n. Elements are 6061-T6 3/16“ sol id
rod with UV stabilized pol yethyl ene Button insul ators and stainless steel
keepers. Thousands of these type elements are i n amateur and commerci al
service wi th NO failures! Booms are constructed of 6063-T832 alumi num
alloy tubing with close-tol erance swaged joi nts. Other key electrical and
mechanical components are CNC machined for accuracy and durabil ity. All
hardware is stainl ess steel except the U-bolts. For uncompromising
performance and l ong term el ectri cal / mechanical i ntegrity, the 2M9SSB
and 2M9FM are unmatched.
Model 2M4 Frequency Range 144 To 148 MHz Gain 9.6 dBi Front to Back 20
dB Typical Beam Wi dth E=54° H=74° Feed Type “T“ Match Feed Impedance
50 Ohms Unbal anced Max VSWR 1.5:1 Input Connector “N“ Female Boom
Length / Di a 48“ / 1“ Max Element Length / Dia 40-1/2“ Turning Radius 55’
Stacki ng Di stance 64“ High & 72“ Wide Mast Size 1-1/2“ to 2“ Nom. Wind area
/ Survival 0.50 Sq. Ft. / 100 MPH Weight / Ship Wt 3 Lbs. / 4 Lbs.
FEATURES: Clean mechanical design, full band coverage and computer
optimized performance make the 2M4 an exceptional antenna. A total ly
sealed and grounded driven el ement design with a unique internal bal un
provides the heart that will beat for years to come. It i s perfect for base and
portable use, with FM, Packet or SSB. Every stati on needs one!!
1 pc: 3 795 Kč
RoHS
GES08901336
MSQUARE 144-146MHz; 9el; 14,1dBi; E35° H38°; 20dBF/B;
SWR1.4typ; Boom 4,5m; 3kg; 50Ohm
Model 2M9FM/2M9SSB Frequency Range 144 To 146 MHz Gain 14.1 dBi
Front to Back 20 dB Typi cal Beam Width E=35° H=38° Feed Type “T “ Match
Feed Impedance 50 Ohms Unbal anced Max VSWR 1.2:1 Typical Input
Connector “N“ Female Boom Length / Dia 14’ 6“ / 1“ To 3/4“ Max Element
Length / Di a 40-5/8“ Turning Radius 8’ Stacking Distance 9’ 6“ High & 10’
Wide Mast Si ze 1-1/2“ to 2“ Nom. Wi nd area / Survi val 1.2 Sq. Ft. / 100 MPH
Weight / Ship Wt 5 Lbs. / 7 Lbs. FEATURES: Up to the mi nute design usi ng a
state-of-the-art computer optimizati on program to deliver the most gai n for
boom l ength of any antenna on the market. Each model’s performance is
optimized for a specifi c mode and frequency range, with no compromises to
achieve unneeded bandwi dth: the 2M9SSB covers 144-146 MHz and the
2M9FM covers 145-148 MHz. Where do you want to make yoursel f heard?
Both models are ideal building blocks for a small turning radius, high-gain
stacked array. Two horizontally polarized, vertical ly stacked 2M9SSB’s yield
the same gain (14.8 dBd) as M2’s 33 ft 2M5WL, but with about 1/2 the turning
radius (8’ - great for QTH’s that won’t permit a l ong boom Yagi). The 2M9FM
can be stacked on a crossboom for the same gain increases, and the turning
radius is sti ll a very manageable 10 ft. The heart of these antennas i s a dri ven
element module originall y desi gned for mariti me AT S satell ite service. All
connectors are O-ring sealed to the CNC machi ned block. Internal
connections are sealed wi th a space-age sil icone gel with nearly 4 times the
dielectric strength of air. The balun connectors are tri ple seal ed on the coax
and nut-seal ed at the block connectors. The type “N“ feed connector uses a
gol d-plated, beryl lium copper center pi n. Elements are 6061-T6 3/16“ sol id
rod with UV stabilized pol yethyl ene Button insul ators and stainless steel
keepers. Thousands of these type elements are i n amateur and commerci al
service wi th NO failures! Booms are constructed of 6063-T832 alumi num
alloy tubing with close-tol erance swaged joi nts. Other key electrical and
mechanical components are CNC machined for accuracy and durabil ity. All
hardware is stainl ess steel except the U-bolts. For uncompromising
performance and l ong term el ectri cal / mechanical i ntegrity, the 2M9SSB
and 2M9FM are unmatched.
1 pc: 6 890 Kč
RoHS
2M12 12el. Yagi
GES08901337
MSQUARE 144-148MHz; 12el.; 14.9dBi; E32° H36°; 22dBF/B;
SWR1.2typ; Boom 6m ; 4kg; 50Ohm
SPECIFICAT IONS: Model 2M12 Frequency Range 144 To 148 MHz Gain
14.9 dBi Front to Back 22 dB Typical Beam Width E=32° H=36° Feed Type
“T“ Match Feed Impedance 50 Ohms Unbalanced Max VSWR 1.5:1 Input
Connector “N“ Female Boom Length / Di a 19.5’ / 1-1/2“ To 1“ Max Element
Length / Dia 40-1/4“ Turning Radius 10’ Stacking Di stance 11’ Hi gh & 11’
Wi de Mast Size 1-1/2“ to 2“ Nom. Wind area / Survival 1.5 Sq. Ft. / 100 MPH
Weight / Ship Wt 8 Lbs. / 9 Lbs. # of Elements 12 FEATURES: T he 2M12
features the l atest computer techni ques for optimization of pattern and gain.
Clean patterns allow you to hear more and interfere less. Clean patterns are
essenti al for stacking. The 2M12 is i deal for stacking i n either pol ari zation.
Two 2M12’s side by side vertical ly pol ari zed are a dynami te FM DX package
and 4 or more are perfect for l ong haul tropo DXing or moonbounce.
Structurall y the 2M12 is sturdy and clean, requiring no boom support.
Elements are 3/16“ 6061-T6 al uminum rod mounted through the boom on
UV stabili zed “button“ insulators. T he boom is a full 1-1/2 i nch di ameter in
the middle taperi ng through two 1-1/4 inch secti ons to sti ff 1 i nch tips. T he
heart of the 2M12 is the unique Driven Element Module: connectors are
O-ring sealed to the CNC machined block and bal un connectors feature triple
O-ring seals. Internal module connections are sealed in a space-age silicone
gel (wi th nearly 4 ti mes the di electric strength of air) to enhance power
handling. T he 2M12: superior performance, long term electrical and
mechanical i ntegrity. Options i nclude power dividers, phasing lines ’H’ frames
and rotators.**Subtract 2.14 from dBi for dBd
1 pc: 5 990 Kč
Action
RoHS
2M5WL 17el. Yagi
GES08901338
MSQUARE 144-148MHz; 17el.; 16.84dBi; E26° H29°; 22dBF/B;
SWR1.2typ; Boom10m ; 7kg; 50Ohm
Model 2M5WL Frequency Range 144 To 148 MHz Gai n 16.84 dBi Front to
Back 22 dB Typi cal Beam Width E=26° H=29° Feed Type “T ““ Match Feed
Impedance 50 Ohms Unbal anced Max VSWR 1.2:1 Input Connector “N“
Female Boom Length / Dia 33’ / 1-1/2“ to 3/4“ Max Element Length / Dia
40-5/8“ Turni ng Radi us 18’ 9“ Stacking Distance 14’ High & 14’ Wi de Mast
Size 2“ Nom. Wi nd area / Survival 2.7 Sq. Ft. / 100 MPH Weight / Ship Wt 13
Lbs. / 14 Lbs. FEATURES: The 2M5WL is designed wi th the SERIOUS “Weak
Signal“ enthusiast in mind. It provides excell ent gain for mini mum weight
and wind load yet i s strong enough to survi ve 100+ mph winds. The modifi ed
fol ded dipole dri ven element is al so unique as it’s center is a CNC machined
block of al uminum fitted with 'O' ringed connectors and access cap. After
factory assembly, the block is fil led with a space age sil icone gel which further
seals and increases dielectric breakdown and arc-over protecti on. The 3/16“
rod elements mount through the boom on UV stabili zed button insul ators. All
hardware is stainl ess steel except for U-bolts. A vertical riser and an overhead
Dacron cord guy system i s supplied for boom support. T his antenna is wi dely
used in EME (W5UN’s 48 2M5WL’s and many others) and large T ropo scatter
arrays. Several optional i tems are availabl e to provide more gai n from your
2M5WL’s. 2 and 4 port power dividers are availabl e for matching stacks of 2 or
4 antennas. 50 Ohm phasing lines model VHF-50-2M5WL2 and
VHF-50-2M5WL4 can be ordered for phasing 2 or 4 antennas together. “H’
frames, OR-2800 and MT-3000 AZ and EL rotators are also availabl e as well
as Rohn and US towers.
420-50-11 11el. Yagi
GES08901351
The 420-50-11 has been computer designed to cover the enti re amateur 70
CM band. It is ideal for repeater linking or any point to poi nt appli cation.
Compari ng it to a common reference, the KLM 420-450-11, it has the same
usable bandwidth with a full one dB more gain and the pattern is much
cl eaner. Clean patterns in most applications provide more rel iable
communi cations wi th l ess intermod. An optional stacking harness i s avai lable
when more than one antenna is required for reduced beamwi dth or
additional gai n. Because the antenna covers the whole band, many users
find it a natural for ATV and general repeater use. Users are surpri sed by the
performance of this compact but potent antenna. Construction i s cl assic M2
for long term el ectri cal and mechani cal integrity. Elements are 3/16“ 6061-T6
rod, mounted through the boom on UV stabilized insulators and locked in
place with stainl ess steel shaft retainers. The driven element module is CNC
machined and all connectors O-ring sealed. Internal connections are
encapsulated in a spaceage sil icone gel with nearl y 4 ti mes the dielectric
strength of air. Balun connectors are tri ple-sealed to the coax.
T he 432-9WL i s a l ot of dynami te in a smal l package. The patterns speak for
themselves. T he antenna has been optimized for use in an array of two or
more antennas, but i ndividual ly, for its size, it beats anything out there in
both pattern and gai n ! Mechanical ly simple, the boom, 1-1/2 inches i n the
middl e, tapers through swaged ends to 1-1/4 and then 1“ diameter ti ps.
Polyethylene button insulators wi th stai nless keepers secure the 3/16“ rod
elements and of course all our antennas feature the CNC machined and ’O’
ring sealed Driven El ement Module ensuring rel iabili ty through weather and
time
GES08901339
432-12EME 12el. Yagi
1 pc: 11 985 Kč
GES08901355
MSQUARE 430-436MHz; 38el; 20.50dBi; E16° H18°; 22dBF/B;
SWR=1.2typ; Boom 9,2m; 5kg; 50Ohm
GES08902100
MSQUARE 430-436MHz; 12el; 16.4dBi; E26° H29°; 23dBF/B;
SWR=1.2typ; Boom 2,95m ; 1,5kg; 50 Ohm
Model 432-12EME Frequency range 430-436 MHz Gain 16.4dBi Front to
back 23 dB VSWR 1.2:1 Typical Beamwi dth E=26°, H=29° Stacking Distance
54"-56" Feed impedance 1.2:1 Typical Input Connector 'N' Female Power
Handl ing 1 KW Boom length 116" Wind Area / Survi val 875 SQ. FT./ 100
MPH Weight / ShipWt. 4 lbs / 5 lbs FEATURES This i s the latest addition to
the high performance M2 family of weak si gnal antennas. As the name
impli es, the 432EME-12 has been specifically designed as a potent yet
compact EME (Moon bounce)array. It is i deal for home and trips (
DXpeditions). Its light weight and rear mount capabi liti es keep phasing li nes
short and mounti ng simple. When used onl y for terrestrial and stacked 4 hi gh
the azimuth beamwidth is sti ll 26 degrees, but the gain is over 20 dBd! EME
CW or JT65B, you’ll be amazed! POLARITY DIVERSITY is possible by
adding 4 more in the opposite polarity to a sli ghtly extended “H” frame. Note
also that i t covers the satellite band! What a nice extra. Constructi on is classic
M2 for long term electrical and mechanical i ntegrity. Elements are 3/16”
6061-T6 rod, mounted through the boom on UV stabili zed insul ators and
locked in place with stainless steel shaft retainers. The driven element
module i s CNC machined and all connectors O-ring sealed. Internal
connecti ons are encapsulated in a space-age sili cone gel . Balun connectors
are tripl e-seal ed to the coax. Our “H” frame used for the above specs i s 2” x
.125 x 60” cross boom and 2” x .065 x 60” risers. Ask about special
configurations for your special project. And don’t forget we make the MT 1000
elevati on rotator. It easil y handles 4X2M9SSB AND 4X or 8X 432EME-12”s.
WHAT A KILLER SYSTEM
1 pc: 3 990 Kč
Action
RoHS
440-18 18el. Yagi
While the 432-13WL produces over 23 dBd gain in a four Yagi array, its also
an excell ent stand alone antenna. And, for the serious amateur it would make
a sensational 16 Yagi 432 array. The driven element is a modified and
adj ustabl e folded di pole. Its heart is a unique machined alumi num Dri ven
Element Module. All three connectors on the module are threaded in and
feature ’O’ ring seals. Internal connections are encapsulated i n a space age
si licone gel with nearl y 4 times the diel ectri c strength of air. Each parasiti c
element i s a sol id 3/16“ rod, mounted through the boom on a UV stabilized,
black pol yethelene button insul ator and l ocked in place with stainl ess steel
shaft retainers. The 432-13WL has been designed for outstanding
performance and long term electrical and mechani cal i ntegrity.
1 pc: 10 690 Kč
RoHS
23CM22EZA 22el. Yagi
GES08901360
MSQUARE 1250-1300MHz; 22el.; 18.2dBi; E24°/H24°; 28dBF/Btyp.;
SWR1.1typ; Boom 2,1m; 0.5kg; 50Ohm
GES08901352
MSQUARE 420-453MHz; 18el.; 16.64dBi; E27° H32°; 23dBF/B;
SWR1.2typ; Boom4,1m; 2kg; 50Ohm
The 440-18 is a computer optimized broadband yagi featuring an excellent
pattern and good gain across its bandwidth. It can be mounted verti cally or
horizontally and i s ideal for stacking two or more for additional gain. Its light
wei ght yet sturdy constructi on keep the cost low and the performance high.
Use it for ATV, OSCAR, FM, LONG HAUL TROPO, ETC. We guarantee you
will be i mpressed. The heart of the 440-18 is a unique Driven Element
Module with superior weather resistance and power handl ing abili ties. All
connectors are O-ring sealed to the CNC machined block and internal
connecti ons are sealed in a spaceage sil icone gel with a di electric strength
nearl y 4 times greater than air. T he Balun coax connectors are triple O-ri ng
sealed. Other key mechanical and electrical parts are CNC machi ned from
6061-T6 alumi num and all hardware except Ubolts i s stai nless steel. T he
440-18 offers you uncompromi sing performance, enduring mechanical
constructi on, and long term el ectri cal i ntegrity. Where else but M2.
1 pc: 5 090 Kč
RoHS
432-13WLA 38el. Yagi
1 pc: 4 390 Kč
RoHS
Model 2M18XXX Frequency Range 144 To 146 MHz Gai n for 1 / 2 / 4 ant.
17.14 / 20.14 / 23.14 dBi Front to Back 26 dB Typi cal Beam Width E=26°
H=28° Feed Type "T" Match Feed Impedance 50 Ohms Unbalanced Max
VSWR 1.2:1 Input Connector "N" Female Boom Length / Dia 36.5' / 1-1/2" To
3/4" Max Element Length / Dia 41" Turning Radius 19' 6" Stacking Distance
14' Hi gh & 14.5' Wide Mast Size 2" Nom. Wi nd area / Survi val 2.9 Sq. Ft. /
100 MPH Wei ght / Ship Wt 14 Lbs. / 16 Lbs. FEAT URES: The 2M18XXX has
been extensively used by many moonbouncers and other weak signal
enthusiasts for the l ast eight years. The clean, sharp pattern yi elds a very
good G/T (gain/temperature i n K) which, i n everyday language, means you
hear more si gnal and less noise. It is i deal as a si ngle antenna or i n stacked
arrays of 24 or more antennas, yiel ding a full 6 dB of stacking gai n for four
antennas! Mechanicall y, the boom is strong in the mi ddle and tapered in 1/4”
steps to reduce weight and wind area. M2 has integrated the computer
optimized design with the unique driven element module. The aluminum
CNC machi ned housing features “O” ring seal s on all three connectors and
internal connecti ons are potted i n sil icon gel than enhances the power
handling capability. That is important to those who feel l ife i s too short for
QRP (Low power)! All hardware is stainl ess except the U-bolts. By all
standards the “18XXX” is a true thoroughbred among VHF antennas!
1 pc: 6 990 Kč
Action
RoHS
RoHS
RoHS
MSQUARE 144-146MHz; 18el.; 17.14dBi; E26° H28°; 26dBF/B;
SWR1.2typ; Boom11m; 7kg; 50Ohm
GES08901354
MSQUARE 420-440MHz; 28 el.; 19.44dBi; E20° H22°; 24dBF/B;
SWR=1.2typ; Boom 6,4m; 4kg; 50Ohm
1 pc: 10 990 Kč
2M18XXX 18el. Yagi
432-9WL 28el. Yagi
MSQUARE; 11el.; 13.44dBi; E34° H43°; 20dBF/B; SWR1.2typ;
Boom1,5m; 2kg; 50Ohm
T he 23CM22EZ is a true product of the computer age. The recently updated
element design i s stamped out holdi ng spacing and element lengths to .003”
tolerance. T he original fiberglass boom has been replaced with 1/2” di a.
alumi num. The metal boom shortens the elements for peak gai n at 1296.
Each antenna performs as perfectly as the next and the gain tops any other
antenna of comparable boom length. With excellent directivity and a very
clean pattern, it is perfect for high gain stacked arrays. Appli cations are long
haul tropo, EME, ATV, Repeater, base station and OSCAR operations. The
'EZ' is handy for ‘hill -topping’ and portabl e uses because of its modest size,
weight, simpl e construction and rear mounting. Structurally, the 22EZ
elements are fabricated in j ust TWO sets, el iminating ALL measurement and
assembly errors. The Broad band folded dipole driven element design is
uni que, with a balun and matching inside the folded di pole i tsel f. External
connections are limited to a singl e O-ring sealed “N” feed. Internal
connections are sealed i n a machi ned and al uminum brazed housing. When
other designs are deteriorating from environmental factors, the '22EZ will still
be as good as new and performing to 'spec'!
1 pc: 6 590 Kč
RoHS
23CM35 35el. Yagi
GES08901361
PS-2M
GES25501283
MSQUARE 1250-1300MHz; 35el.; 20.94dBi; E17°/H18°;
25dBF/Btyp.; SWR=1.2typ; Boom3,1m; 2kg; 50Ohm
MSQUARE Polarization Switch for 2MCP14, 2MCP22
The original 23CM35 has recently been re-designed and optimized for 1269
(satell ite) and 1296 (terrestrial and EME) use. A 1” di ameter center boom
section has been added to strengthen and stiffen the boom and make the
shippi ng box smaller, savi ng costs. T he dri ven element has been modified to
make matchi ng easier and hol d more securely. Perfect bal ance is achieved
with bal un 'i nside' the folded di pole itself. This eliminates connectors and
cabl e and, as al ways with M2 driven elements, the whol e assembly i s sealed.
When other designs will have succumbed to wind and weather, the 100
MPH-rated 23CM35A wi ll be as good as new and sti ll performing to 'spec'!
The '23CM35' is an outstanding performer for “hi ll-topping" or base stati on
appli cations. Gai n i s relatively flat across the band so no matter your
appli cation, weak signal EME or troposcatter, ATV, FM repeater use, or future
OSCAR appl icati ons, you wil l find the 23CM35A to be an outstandi ng
performer. T he di recti vi ty, gain and the clean pattern wi ll astound you.
Phasing cables, power di vi ders and stacking kits are available for building a
super-gain system
See 2MCP14 , 2MCP22 FEAT URES Thi s handy tool provi des a pol ari ty
swtch, from right hand circular to l eft hand circular and back in the case of
satelli te reversal. Made specificall y for those avid AMSAT users, and for
others egar to get up on the newly l aunched Phase 3-D satellite. It provi des
TRUE RF switchi ng at up to 250 watts! T he kit is perfect for upgrading your
existi ng antenna or adding i t to a newl y ordered one, and install ati on is a
snap. All you have to do i s unbolt the old dri ven element and pl ug in the new
one. Just dont switch it whil e keyed - they don't respond well to hot swi tching.
1 pc: 4 990 Kč
Action
RoHS
2MXP20
GES08901343
MSQUARE 144-146MHz; 20el.; 15.3dBi; E30° H34°; 25dBF/B; SWR
1.5m ax.; Boom 6.5m; 5kg; 50 Ohmů
2MXP32
Frequency range 144 to 144.6 MHz Typical gain 15.8 dBd Front to back,
Typical 24 dB Beamwidth 24 Degrees Feed impedance 50 Ohms VSWR
1.4:1 Max Stacking Distance 4,6m až 4,8m / H & E Input Connector "N"
Female Power Handl ing 1.5 KW Boom length and diameter 40' 11" (12,3m) /
2", 1-1/2", 1-1/4" & 1" Maximum element length 42" (1,07m) T urning radius
24' (7,2m) Wi nd Area / Survival 4.2 sq. ft. (0,42 m2) / 100MPH (180km/hod.)
Weight / ShipWt. 10 kg / 11 kg
1 pc: 15 790 Kč
RoHS
436CP30
1 pc: 7 090 Kč
GES08901345
MSQUARE 144-144.6MHz; 32el.; 17.9 / 23.9dBi; 24°; V+H;
24dBF/B; SWR=1.4max; Boom 12.3m; 10kg; 50 Ohm
GES08901356
MSQUARE 432-440MHz; 30el; 15.50dBic; Circul.; 22dBF/B;
SWR1.6max; Boom 3m; 2,5kg; 50Ohm
RoHS
VHF Beams, Circual Polarisation
2MCP14
GES08901341
MSQUARE 143-148MHz; 14el.; 10.2dBic; 52°Circ; 24dBF/B; SWR
1.3typ; Boom 3,2m; 3kg; 50Ohm
For polarization swi tching use the PS-2M GES 255 012 83 (extra order). T he
2MCP14 is a light, medium performance circul arl y polarized antenna
designed to work across the two meter amateur band. Optimum match and
gain are between 144 & 147 MHz for the satellite band. Computer desi gn
techniques help keep spurious side l obes low down for opti mum signal to
noise ratios. This antenna features the same CNC machined, O-ring and
silicone-gel sealed, driven element assembli es common to all M2 Yagi
antennas. This insures years of troubl e free performance regardless of
weather. Optional i tems include a heavy duty fiberglass 2“ O.D. x 1/4“ wall
boom wi th a 1-1/2“ soli d alum center section to fi t through the Yaesu 5400
and 5600 series az-el rotator (model HDFG boom ki t), 2M2PORT power
divider and vhf-50- 2MCP14-2 phasi ng lines. We also can provide ’H’ frames
and larger rotators, OR-2800DC (az) and MT-1000 (el). A 136R-14C and a
149T-14C model are al so avai lable for the AT S satellite users. Higher gain
antennas wi th 22 el ements are al so avail able for al l VHF satellite frequencies
Thi s dual pol ari zed yagi was computer designed for the seri ous
Moonbouncer. The very good G/T is a result of low side and back lobes and
the desi gn has been optimized for stacking. T his antenna is remarkabl e in
that the stacking gai n for four antennas exceeds 6 dB. Even using a single
Horizontal /Verti cal relay, you have a moonbounce package that can
outperform larger, linear arrays. Additi onal relay switching providing 4
different types of si gnals. Losses from speci al polarity and Faraday rotati on
vi rtuall y disappear. EME rel iabili ty approaches 100%. M2’s new 2MXP20
antennas, power dividers and phasi ng lines (using T imes’ new li ght-weight,
low-loss LMR400 and/or LMR600 cable) coupled with ’T ’ brace kits, fiberglass
H-frame packages, OR2800P Azimuth Rotator, and our New MT-1000
Elevation Motor provide the buil ding blocks for a whol e new generati on of
high performance EME arrays.
1 pc: 8 890 Kč
For polarizati on switching use PS-70CM GES 255 012 84 (extra order) The
436CP30 is a practi cal si zed, yet hi gh performance ci rcular pol ari zed
antenna with a remarkably clean pattern. The pattern is important i n order to
match the antenna’s noi se temperature with modern low noise preamps. T his
antenna is ideal for satelli te work but is also excellent for terrestrial uses l ike
ATV, repeater operation, and l ong haul tropo DX. The CNC machined dri ven
element module is O-ring seal ed and weather tight for l ow maintenance and
l ong-term peak performance. Internal connected are encapsulated i n a
space-age sili cone gel that seals out moisture and improves power handling.
T he 3/16“ 6061-T 6 rod el ements are centered to mini mi ze interacti on and
maintain good elli pti ci ty. Insulators are UV stabil ized and locked i n place wi th
stainless keepers. Rugged construction, uncompromising performance for the
boomlength: thats the M2 436CP30
1 pc: 7 890 Kč
RoHS
2MXP28
GES08901344
MSQUARE 144-145MHz; 28el.; 17.2dBi; E25° H26°; 22dBF/B;
SWR=1.4max; Boom 10.3m ; 9kg; 50 Ohm ů
RoHS
436CP42UG
GES08901357
MSQUARE 430-438MHz; 42el.; 18.9dBic; 21°Circ; 25dB F/B; SWR
1.5max; 4kg; 50Ohm
1 pc: 7 890 Kč
Action
RoHS
2MCP22
GES08901342
MSQUARE 144-148MHz; 22el.; 14.39dBdic; 38°Circ; 25dBF/B;
SWR 1.4typ; Boom 5.5m; 4.5kg; 50Ohm
For polarizati on switchi ng use the PS-2M GES 255 012 83 (extra order). Thi s
cross polarized Yagi was computer desi gned for the serious OSCAR user. T he
average side and back lobes power have been reduced by approximately 10
dB over any previ ous design, enhanci ng signal to noise rati o and putti ng all
your power where it wil l do the most good. The 2MCP22 i s i deal for general
use over the ENTIRE two meter band from FM to SSB and CW DX. Arrays of
two or more will even permi t moonbounce contacts using the old rel iable
passive repeater in the sky. The uni que Driven Element Modules are CNC
machined and feature O-ri ng sealed connectors. Internal connections are
encapsulated i n a space age silicone gel wi th nearly 4 times the dielectric
strength of air. The 2MCP22 is our finest circular polarized antenna. We are
confident you will be impressed with the 2MCP22 from the moment you open
the box unti l you’ve worked DXCC and beyond! Optional items include HDFG
fiberglass crossboom kit compatible with Yaesu 5400 and 5600 seri es az-el
rotators, power di vi ders 2M2PORT and 2M4PORT, polarity switch, phasi ng
lines VHF-50-2MCP22(2) or (4), ’H’ frames, OR-2800 azi muth and MT-1000
and MT-3000 elevation rotators / positioners.
1 pc: 11 985 Kč
RoHS
Thi s dual pol ari zed yagi was computer designed for the seri ous
Moonbouncer. The very good G/T is a result of low side and back lobes. and
the design has been optimized for stacking (see patterns). This antenna i s
remarkable in that the stacki ng gain for four antennas exceeds 6 dB. Coupl ed
with various Polarity Diversity Switching schemes, you have a moonbounce
package that easil y outperforms larger, conventional arrays in receive
capabi liti es. Si mple rel ay switching can provi des 4 di fferent types of discrete
receiving polarizati ons: Horizontal , Verti cal, Ri ght Orthogonal , and Left
Orthogonal. You are al ways within a few 10ths of a dB of the peak si gnal you
are seeking. Signal losses from spacial polarity and Faraday rotati on virtual ly
disappear. EME reli ability approaches 100%. M2’s new 2MXP28 antennas,
power di vi ders and phasi ng lines (usi ng Times’ new light-weight, low-loss
LMR400 and/or LMR600 cable) coupled with ’T’ brace ki ts and fiberglass
H-frame packages, provi de the bui ldi ng bl ocks for a whole new generation of
high performance EME arrays
For polarizati on switching use PS-70CM GES 255 012 84 (extra order). The
436CP42UG (Ul tra-Gai n) sets a new performance standard for UHF circul ar
pol ari zed antennas. Gain and F/ B are excellent. T he boom length is
matched to the 2MCP22, and together they form an unbeatable satelli te
communications package. T he extremely cl ean pattern maximizes forward
gai n and F/B. The pattern is important in order to match the antenna’s noise
temperature with modern l ow-noise preamps. The CP42 is also excell ent for
ATV, repeater operati on, and long haul tropo DX and EME around 432 MHz.
T he driven el ement and ’T’ blocks are CNC machined, with connectors O-ring
seal ed for low mai ntenance and l ong-term peak performance. Internal
connections are embedded in a space-age sil icone gel that seals out
moisture and improves power handling. The 3/16“ 6061-T6 rod el ements are
centered in the boom to minimize interacti on and mai ntain low ell ipticity.
Insulators are UV stabi lized and locked in place with stainless retainers. The
central boom section is 1-1/2“ dia., tapering, front and rear,through 1-1/4“
sections to 1“ ends.If you are looki ng for rugged construction and top-notch
performance, For EME use, M2 can suppl y an opti onal polarity switch and
parts needed to convert these to dual polarity Yagis. Contact us for more
detail s.
1 pc: 11 190 Kč
1 pc: 13 990 Kč
RoHS
RoHS
PS-70CM
GES25501284
MFJ-912 BALUN
GES08900983
MSQUARE Polarization Switch for 436CP30, 436CP42UG
High power W9INN 4:1 Balun Box, 1500W full legal limit
See 436CP30 , 436CP42UG FEATURES This handy tool provides a pol ari ty
swtch, from ri ght hand circular to l eft hand circular and back in the case of
satelli te reversal. Made specificall y for those avid AMSAT users, and for
others egar to get up on the newly launched Phase 3-D satellite. It provi des
TRUE RF switchi ng at up to 250 watts! T he kit is perfect for upgrading your
existi ng antenna or adding i t to a newly ordered one, and instal lation is a
snap. All you have to do i s unbolt the old dri ven element and pl ug in the new
one. Just dont switch it whil e keyed - they don't respond well to hot swi tching.
Uses giant cores, wound with Teflon wire. Heavy duty ceramic feedthru
insulators. Di mensi ons 83 x 58 x 178mm.
1 pc: 4 590 Kč
POWER DIVIDER 2M 4PORT
GES08901372
MSQUARE Power Divider for 2m Band, 1IN/4OUT, N-fem ale,
50Ohm., 1.5kW
1 pc: 2 890 Kč
1 pc: 1 860 Kč
Action
RoHS
RoHS
MFJ-913 BALUN
GES08900986
Balun 4:1;300Wmax; 200/50Ohm; 160-10m; Centr.Ins ulat.
Weatherproof; dia.51x115mm
POWER DIVIDER 70CM 2PORT
GES08901373
MSQUARE Power Divider for 70cm Band, 1IN/2OUT, N-female,
50Ohm., 1.5kW
Action
RoHS
Coax cables, rf connectors
Connectors, coax cables
GES08902233
See please " Coaxial cables , RF connectors "
1 pc: 3 060 Kč
RoHS
POWER DIVIDER 70CM 4PORT
GES08901374
MSQUARE Power Divider for 70cm Band, 1IN/4OUT, N-female,
50Ohm., 1.5kW
Baluns, Duplexers, Isolators, Power
Dividers
1 pc: 790 Kč
RoHS
MFJ-919 CURRENT BALUN
GES08900996
4:1 Balun; 1,5kWmax; 200/50Ohm; 160-10m; Centr.Insulat.
Weatherproof; 89x89x64mm
Baluns
BN-86 BALUN
GES08901365
HY-GAIN Balun 1:1, 3-30MHz/+-1dB, 1500W for SWR max.2:1,
50Ohm, SO-239
1 pc: 2 890 Kč
Action
RoHS
POWER DIVIDER 23CM 2PORT
1 pc: 2 150 Kč
The MFJ-919 is a 1500 Watt true current baluns/antenna center insulators
that transforms 200 ohms to 50 ohms. Transmission Line Transformer
constructi on using 100 ohm characteristi c impedance transmi ssion l ine gives
flat 160-10 Meter response. Large low permeability ferrite cores easily handle
ful l power. SO-239, stai nless steel hardware with direct 14 gauge stranded
copper wi re connection to antenna. Heavy duty weather housi ng. Measures
3-1/2 x 3-1/2 x 2-1/2 i nches.
RoHS
BN-4000N BALUN
GES08901364
GES08901375
MSQUARE Power Divider for 23cm Band, 1IN/2OUT, N-female,
50Ohm., 1.5kW
1 pc: 1 490 Kč
Action
RoHS
POWER DIVIDER 23CM 4PORT
GES08901376
MSQUARE Power Divider for 23cm Band, 1IN/4OUT, N-female,
50Ohm., 1.5kW
1 pc: 990 Kč
Action
RoHS
1 pc: 2 890 Kč
Action
RoHS
HY-GAIN / Beam, Dipole Current Balun, 1-54MHz, 4kW, N-female
1 pc: 3 180 Kč
MFJ-911 BALUN
GES08900978
Balun 4:1, flat response 1.8-30MHz, 200 Ohm /50Ohm , 300W
Power Dividers
POWER DIVIDER 6M 2PORT
Antenna Isolators
GES08902115
MSQUARE Power Divider for 6m Band, 1IN/2OUT, N-female,
50Ohm., 1.5kW
MFJ-16C01 ANTENNA INSULATOR
GES08900439
Glazed Ceram ic Dipole end Ins ulator
Hard styl e power di vi der. Made from alumini um alloy tubing brazed into
machined j unction blocks. Center conductor are cooper, hel d in place with
Teflon spacers. All connectors are o-ring sealed.
1 pc: 4 590 Kč
POWER DIVIDER 6M 4PORT
GES08902189
MSQUARE Power Divider for 6m Band, 1IN/4OUT, N-female,
50Ohm., 1.5kW
1 pc: 5 355 Kč
Thi s transmission li ne transformer uses low-permeability ferrite cores.
Dimensions 64 x 121 x 26mm.
1 pc: 665 Kč
POWER DIVIDER 2M 2PORT
GES08901371
MSQUARE Power Divider for 2m Band, 1IN/2OUT, N-female,
50Ohm., 1.5kW
RoHS
MFJ-911H BALUN
1 pc: 29.00 Kč
GES08901895
RoHS
MFJ-16C06 ANTENNA INSULATOR
Switchable balun 1:1 or 4:1, flat response 1.8-30MHz,
200Ohm /50Ohm , 300W
GES08900440
6-Pack - Glazed Ceram ic Dipole end Ins ulator
1 pckg.: 119.00 Kč
RoHS
MFJ-16C100 ANTENNA INSULATOR
1 pc: 3 060 Kč
RoHS
1 pckg.: 2 090 Kč
RoHS
1 pc: 930 Kč
RoHS
GES08900441
100-Bulk Pack Glazed Ceramic Dipole end Insulator
MFJ-16D01 ANTENNA INSULATOR
GES08900442
Center Insulator for coaxial cable or line 450 Ohm
RC5A-3P Antenna Rotor Create
GES08901666
CREATE antenna rotator, AZ angle 370°, m otor snail gearing, PC
com patible
RC10S Antenna Rotator Create
GES08901705
CREATE antenna rotor for large commercial antennas (Log-Per)
Antenna rotator 110/230VAC 150VA, maximum vertical load 700kg,
horizontal load 1000kg, rotati ng torque 155Nm, brake torque 1960Nm, worm
gear at motor, variable speed 75-110 sec., reversi ng delay 3sec., mast
diameter 48-63mm, 360° scale, preset, weight 7kg rotator and 2kg controler,
needs 7 core cable (0.75mm2 up to 50m lenght, 1.25mm2 up to 80m
lenght). Interface for external control unit (RAC825 GES 089 017 04 or other)
or a PC interface - see schmidt-alba.de/English/ERC/erc.html or
www.ea4tx.com
1 pc: 24 995 Kč
RoHS
RC5B-3 Antenna Rotor Create
GES08901668
CREATE antenna rotator, AZ angle 370°, m otor snail gearing
Robust, weather resistant, UV stable central antenna i nsulator for heavy
antenas (di pole etc.). .
Antenna rotator for l arge antenna systems. Maximum vertical l oad 1000kg,
horizontal l oad 1500kg, rotating torque 280Nm, brake torque 3700Nm, worm
gear at motor, variable speed 75-110 sec., reversi ng del ay 3sec., mast
diameter 66-77mm, 360° scale, preset, 230VAC/170VA, weight 27,5kg rotator
and 2kg controler, needs 7 core cable.
1 pc: 185.00 Kč
RoHS
1 pc: 69 900 Kč
RoHS
RC10SP Antenna Rotator Create
Rotators and Accessories
CREATE Rotators and accessories
RC5-1 Antenna Rotor Create
GES08901804
CREATE antenna rotor for large commercial antennas (Log-Per)
GES08901671
CREATE antenna rotator, AZ angle 370°, variable speed
Antenna rotator 110/230VAC 200VA, maximum vertical load 700kg,
horizontal load 1000kg, rotati ng torque 210Nm, brake torque 2480Nm, worm
gear at motor, variable speed 75-110 sec., reversi ng delay 3sec., mast
diameter 48-63mm, 360° scale, preset, weight 7kg rotator and 2kg controler,
needs 7 core cable (0.75mm2 up to 50m lenght, 1.25mm2 up to 80m
lenght).
1 pc: 34 995 Kč
RoHS
RC5B-3P Antenna Rotor Create
Antenna rotator for l arge antenna systems. Maximum vertical l oad 1000kg,
horizontal l oad 1500kg, rotating torque 280Nm, brake torque 3700Nm, worm
gear at motor, variable speed 75-110 sec., reversi ng del ay 3sec., mast
diameter 66-77mm, 360° scale, preset, 230VAC/170VA, weight 27,5kg rotator
and 2kg controler, needs 7 core cable. Interface for external control unit
(RAC825 GES 089 017 04 or other) or a PC interface - see schmidtalba.de/English/ERC/erc.html or www.ea4tx.com
1 pc: 69 900 Kč
RoHS
MC-2 Mast clamp Create
GES08901693
CREATE Lower Mast Clamp w/Coupling Adaptor
GES08901665
CREATE antenna rotator, AZ angle 370°, m otor snail gearing, PC
com patible
Antenna rotator 110/230VAC 200VA, maximum vertical load 700kg,
horizontal load 1000kg, rotati ng torque 210Nm, brake torque 2480Nm, worm
gear at motor, variable speed 75-110 sec., reversi ng delay 3sec., mast
diameter 48-63mm, 360° scale, preset, weight 7kg rotator and 2kg controler,
needs 7 core cable (0.75mm2 up to 50m lenght, 1.25mm2 up to 80m
lenght). Interface for external control unit (RAC825 GES 089 017 04 or other)
or a PC interface - see schmidt-alba.de/English/ERC/erc.html or
www.ea4tx.com
1 pc: 35 995 Kč
RoHS
Antenna rotator 110/230VAC 90VA, maximum verti cal load 400kg, horizontal
load 800kg, rotating torque 60Nm, brake torque 780Nm, worm gear at motor,
variabl e speed 75-110 sec., reversi ng delay 1sec., mast diameter 48-63mm,
360° scale, wei ght 4kg rotator and 2kg controler, needs 7 core cable
(0.75mm2 up to 50m lenght, 1.25mm2 up to 80m l enght).
1 pc: 13 565 Kč
RoHS
RC5-1DC Antenna Rotor Create
GES08901672
CREATE antenna rotator 12VDC, m ax. angle 380°, variable speed
(max.360°/1min.)
Antenna rotator with DC motor, power supply 12-15VDC, max.3A, maxi mum
verti cal load 400kg, rotating torque 50Nm, brake torque 880Nm, worm gear at
motor, variabl e speed 60-160 sec., reversi ng delay 0sec., mast diameter
48-63mm, 360° scale, weight 5kg rotator, 2kg controler, needs 5 core cable.
1 pc: 13 990 Kč
RoHS
RC5-3 Antenna Rotor Create
GES08901995
CREATE antenna rotator, AZ angle 370°, m otor snail gearing
Antenna rotator 110/230VAC 90VA, maximum verti cal load 400kg, horizontal
load 800kg, rotating torque 60Nm, brake torque 880Nm, worm gear at motor,
variabl e speed 75-110 sec., reversi ng delay 1sec., mast diameter 48-63mm,
360° scale, preset, wei ght 4kg rotator and 2kg controler, needs 7 core cable
(0.75mm2 up to 50m lenght, 1.25mm2 up to 80m l enght).
1 pc: 16 990 Kč
RoHS
RC5-3P Antenna Rotor Create
RC5B-4 Antenna Rotor Create
GES08901996
CREATE antenna rotator, AZ angle 370°, m otor snail gearing
Antenna rotator 110/230VAC 200VA, maximum vertical load 700kg,
horizontal load 1000kg, rotati ng torque 210Nm, brake torque 2480Nm, worm
gear at motor, variable speed 94-144 sec., reversing del ay 3sec., mast
diameter 48-63mm, 360° scale, preset, weight 7kg rotator and 2kg controler,
needs 7 core cable (0.75mm2 up to 50m lenght, 1.25mm2 up to 80m
lenght).
1 pc: 2 595 Kč
RoHS
UC-1 Universal coupler
GES08901930
CREATE Universal Coupler
1 pc: 34 990 Kč
Action
RoHS
RC5B-4P Antenna Rotor Create
GES08901669
CREATE antenna rotator, AZ angle 370°, m otor snail gearing, PC
com patible
Antenna rotator 110/230VAC 200VA, maximum vertical load 700kg,
horizontal load 1000kg, rotati ng torque 210Nm, brake torque 2480Nm, worm
gear at motor, variable speed 94-144 sec., reversing del ay 3sec., mast
diameter 48-63mm, 360° scale, preset, weight 7kg rotator and 2kg controler,
needs 7 core cable (0.75mm2 up to 50m lenght, 1.25mm2 up to 80m
lenght). Interface for external control unit (RAC825 GES 089 017 04 or other)
or a PC interface - see schmidt-alba.de/English/ERC/erc.html or
www.ea4tx.com
1 pc: 39 995 Kč
RoHS
CREATE 7-25J conector 7PIN male
GES08901885
Spare connector for CREATE RC5 rotor (7 PIN, Jack=male)
GES08901670
CREATE antenna rotator, AZ angle 370°, m otor snail gearing, PC
com patible
Absorber-j unction UC-1 compense rotator's swings and avoids rotator before
damage. Absorber is mounted between rotator and rotator base. Absorber
besi des tensi on caused by not perpendicular mounting. Absorber has no
rubber sil ent blocks. Rugged upper plate l ies on massive central spike of lower
plate. Both plates are fixed by screws fix mounted to lower plate and passing
thru oval hol es of upper pl ate. Plates material is gal vani zed steel. Both plates
have necessary mounti ng holes for CREAT E rotators.
1 pc: 1 995 Kč
RoHS
Antenna rotator 110/230VAC 90VA, maximum verti cal load 400kg, horizontal
load 800kg, rotating torque 60Nm, brake torque 880Nm, worm gear at motor,
variabl e speed 75-110 sec., reversi ng delay 1sec., mast diameter 48-63mm,
360° scale, preset, wei ght 4kg rotator and 2kg controler, needs 7 core cable
(0.75mm2 up to 50m lenght, 1.25mm2 up to 80m lenght). Interface for
external control unit (RAC825 GES 089 017 04 or other) or a PC interface see schmidt-alba.de/English/ERC/erc.html or www.ea4tx.com
CK46 Thrust bearing Create
GES08901677
CREATE Conical thrus t bearing for antenna mast dia.40-65mm
1 pc: 17 995 Kč
1 pc: 290.00 Kč
RoHS
RC5A-3 Antenna Rotor Create
GES08901667
CREATE antenna rotator, AZ angle 370°, m otor snail gearing
Action
RoHS
CREATE 7-25P conector (7 PIN,
Plug=female) for cable
GES08901884
Spare cable connector for CREATE RC5 rotor (7 PIN, Plug=female)
1 pc: 1 795 Kč
RoHS
1 pc: 490.00 Kč
Action
RoHS
Antenna rotator 110/230VAC 150VA, maximum vertical load 700kg,
horizontal load 1000kg, rotati ng torque 155Nm, brake torque 1960Nm, worm
gear at motor, variabl e speed 75-110 sec., reversing delay 3sec., mast
diameter 48-63mm, 360° scale, preset, weight 7kg rotator and 2kg controler,
needs 7 core cabl e (0.75mm2 up to 50m lenght, 1.25mm2 up to 80m
lenght).
1 pc: 21 995 Kč
Action
RoHS
AER-5 Azimuth-Elevation Antenna
Rotator Create
GES08901904
CREATE rotor AZ/EL; 35sec360° / 25sec90°; Rot.66/77Nm;
Brake980/1100Nm; Weight12kg
RAC 825 Satellite and EME AZ-EL
Tracker
GES08901704
CREATE Satellite and EME Tracker for AZ-EL control of CREATE
rotors
Filters (Front, Roofing, IF, AF)
Front-end filters 50 Ohm
Front-end-Filters , which may be used where there are many
s ignals, such as locations near high power broadcast transmitters
or m ulti-trans mitter contest stations. Have 50 Ohm input and
output impedances , and are designed to go in front of a receiver.
They can be transmitted through at very low levels under 0dBm.
AER-5 is both azimuth and elevation combi ned rotator made of combini ng 2
rotators, ERC51 and RC5-3P in one solid set. Although the mountable size
and weight of antenna is limited below within 50kg, such an antennas
popular among Satel lite lovers, like those antennas commonl y used such as 5
to 32 element 2m si ngle Yagi with 5 to 42 element 70cm single Yagi will
exactl y be most suitable and meet the request. AER-5 is computer
compatible. Perfect high performance antenna i s a type from M2 (USA), for
example
www.ges.cz/en/broadcasting-radi o/antennas-and-accessories
/vhf-beams-circual-polarisation/SRAX.html? Rotator is ful ly controll ed with
CREATE RAC825 GES 089 017 04 or a PC interface - see schmi dtalba.de/Engli sh/ERC/erc.html or www.ea4tx.com
Sofisticated control unit. Satel lite tracker for control ling an antenna for
auto-tracki ng a communication satell ite, EME communication, and for
receiving a noise sources of other orbi t pl anets etc. Most standard AZ and EL
rotors can be i nterfaced. Bui lds in CPU and firmware. Two operation type: 1)
Terminal Mode - RAC 825 works standalone 2) Host Mode - connected to PC
with running tracki ng software (Nova). CPU: I8031, 32kB with l ithium battery
backup, 64kB ROM, ADC: MPD7004C 10Bit / 8Ch, RT C62421B, PPI 8255, 24
Input/Output, RS 232 9600Bps, CAT Radi o Interface 4800/9600/19200 for
Icom (IC275, IC375, IC821, IC970 etc. with CAT), Kenwood (TS711, T S790,
TS811 etc. with CAT) and Yaesu (FT736, FT847 etc with CAT).
D250mmxW200mmxH80mm. Weight 2kg.
INRAD-807 FRONT END FILTER
160M
GES08901960
INRAD Front-end-filter 4 poles, 1822.5kHz, 5kHz/-1dB,
23kHz/-60dB, 50Ohm., <0dBm
1 pc: 20 990 Kč
RoHS
1 pc: 38 990 Kč
RoHS
ERC51 Elevation Antenna Rotator
Create
GES08901673
CREATE elevation rotor; 25-55s ec/90°; Torque - rotation 180Nm /
brake 980Nm; RAC825 compatible
HY-GAIN Rotators and accessories
AR-303X Light Beam / TV Rotator
GES08902237
Light Beam / TV Rotator
1 pc: 2 790 Kč
RoHS
INRAD-808 FRONT END FILTER
80M
GES08901961
INRAD Front-end-filter 4 poles, 3505.0kHz, 10kHz/-1dB,
50kHz/-60dB, 50Ohm., <0dBm
Elevation antenna rotor. Vertical load 50kg max., horizontal load 200kg.
max., rotating torque 190Nm, brake torque 980Nm, variable speed
25-55sec/90°, reversing delay 0sec., mast diameter 48-63mm, motor
consumpti on 150VA, rotation angle preset, weight 7,5kg rotator and 2kg
control er, needs 7 core cable (0.75mm2 up to 50m lenght, 1.25mm2 up to
80m lenght). Perfect high performance antenna is a type from M2 (USA), for
example
www.ges.cz/en/broadcasting-radi o/antennas-and-accessories
/vhf-beams-circual-polarisation/SRAX.html? Rotator is ful ly controll ed with
CREATE RAC825 GES 089 017 04 or a PC interface - see schmi dtalba.de/Engli sh/ERC/erc.html or www.ea4tx.com
1 pc: 15 990 Kč
Action
RoHS
ERC51D Elevation Antenna Rotator
Create
GES08901675
Desi gned for the use of smal l UHF, VHF, 6-Meter, T V and FM nd other
lightweight antennas. Rugged heavy-duty rotator is bui lt in a weather-proof
one pi ece cast al uminum housi ng. Has preci sion metal gears and steel thrust
beari ngs for durability. Includes rotator, control ler, mount clamps and
hardware. Uses 220/240 VAC.
1 pc: 2 690 Kč
CREATE elevation rotor 12-15VDC; 18-60sec/90°; Rotat.50Nm /
brake 100Nm torque; RAC825 com patible
Elevation antenna rotor wi th DC motor. Vertical load 50kg max., horizontal
load 200kg. max., rotating torque 50Nm, brake torque 100Nm, variabl e speed
18-60sec/90°, reversi ng delay 0sec., mast diameter 48-63mm, motor voltage
12-15VDC, rotation angle preset, wei ght 7,5kg rotator and 2kg controler,
needs 6 core cable. Perfect high performance antenna is a type from M2
(USA),
for
example
www.ges.cz/en/broadcasti ng-radio/antennasand-accessories/vhf-beams-circual-pol ari sati on/SRAX.html? Rotator is ful ly
control led with CREAT E RAC825 GES 089 017 04 or a PC interface - see
schmidt-al ba.de/Engl ish/ERC/erc.html or www.ea4tx.com
RoHS
AR-500X Automatic / Remote
rotator
GES08902236
1 pc: 2 790 Kč
Remote Controlled Rotator/Controller for small VHF, UHF or 6m
antennas
RoHS
INRAD-801 FRONT END FILTER
40M
GES08900190
INRAD Front-end-filter 6 poles, 7007.5kHz, 15kHz/-1dB,
32kHz/-60dB, 50Ohm., <0dBm
1 pc: 18 990 Kč
Action
RoHS
ERC5A Elevation Antenna Rotator
Create
GES08901674
CREATE elevation rotor; 75-110 sec/90°, rotat. 480Nm / brake
2800Nm torque, RAC825 compatible
Elevation antenna rotor for l arge system. Verti cal load 330kg max., horizontal
load 600kg. max., rotating torque 480Nm, brake torque 980Nm, variable
speed 75-110sec/90°, reversing del ay 0sec., mast di ameter 48-61mm, motor
consumpti on 150VA, rotation angl e preset, wei ght 17kg rotator and 2kg
control er, needs 7 core cable (0.75mm2 up to 50m lenght, 1.25mm2 up to
80m lenght). Perfect high performance antenna is a type from M2 (USA), for
example
www.ges.cz/en/broadcasting-radi o/antennas-and-accessories
/vhf-beams-circual-polarisation/SRAX.html? Rotator is ful ly controll ed with
CREATE RAC825 GES 089 017 04 or a PC interface - see schmi dtalba.de/Engli sh/ERC/erc.html or www.ea4tx.com
Remote Controlled Rotator/Controller Designed for the use of small UHF, VHF,
6-Meter, TV and FM antennas. Has programmable antenna control ler with
remote-control . AR-500X remembers up to 12 antenna directions even after a
power outage! Control all functions with the remote control or console. T he
control console di splays location chosen and relative position. Rugged
heavy-duty rotator is built i n a weather-proof one piece cast aluminum
housing. Has precision metal gears and steel thrust beari ngs for durabi lity.
Includes rotator, control ler, mount cl amps and hardware. Includes rotator,
control ler, 3-device uni versal remote, mount clamps and hardware. Uses 220
VAC
1 pc: 2 790 Kč
RoHS
INRAD-802 FRONT END FILTER
20M
GES08901959
INRAD Front-end-filter 6 poles, 14010.0kHz, 20kHz/-1dB,
45kHz/-60dB, 50Ohm., <0dBm
1 pc: 3 490 Kč
RoHS
1 pc: 36 995 Kč
RoHS
1 pc: 2 790 Kč
RoHS
INRAD-804 FRONT END FILTER
20M RTTY
GES08901962
INRAD Front-end-filter 6 poles , 14080.0kHz, 20kHz/-1dB,
45kHz/-60dB, 50Ohm., <0dBm
INRAD-350 CW 9MHZ FILTER
9000kHz 600Hz
GES08901965
INRAD CW Set 4x crystal + 5x SMD capacitor for filter
9000kHz/600Hz, Z=200 Ohms
AOR
INRAD-724 AOR 455kHz 3800Hz AM
AR5000
GES08902163
INRAD 3800Hz/455kHz AM 7-pole Collins filter
Filter 3800Hz/-6dB, 455kHz, AM. Impedance Zin = Zout = 2000 Ohm // 30pF.
Typical Insertion Loss < 6dB. Collins 7 pole Mechanical fi lter. For AOR
AR5000
1 pc: 2 790 Kč
Fil ter kit wi th center frequency 9000kHz and 600Hz wi de for CW. Four
speci all y cut and color coded crystals with 5 SMD capacitors are suppli ed with
each kit. Input and output impedance 200 Ohms. Kit i s just a ticket for a QRP
transcei ver or recei ver project.
RoHS
INRAD-805 FRONT END FILTER
15M
1 pc: 3 490 Kč
RoHS
1 set: 645 Kč
GES08901963
INRAD Front-end-filter 6 poles , 21010.0kHz, 20kHz/-1dB,
45kHz/-60dB, 50Ohm., <0dBm
RoHS
INRAD-351 SSB 9MHZ FILTER
9000kHz 2400Hz
GES08901966
INRAD SSB Set 4x crystal + 5x SMD capacitor for filter
9000kHz/2400Hz, Z=200 Ohm s
Fil ter kit with center frequency 9000kHz and 2400Hz wide for SSB. Four
speci all y cut and color coded crystals with 5 SMD capacitors are suppli ed with
each kit. Input and output impedance 200 Ohms. Kit i s just a ticket for a QRP
transcei ver or recei ver project.
Collins
INRAD-724 COLLINS 455kHz
3800Hz AM 75S-3B/C
GES08902161
INRAD 3800Hz/455kHz AM 7-pole Collins filter
1 set: 645 Kč
RoHS
INRAD-2301 CW 9MHz FILTER
8999,3kHz 250Hz
GES08902165
INRAD CW crystal filter 8999,3kHz / 250Hz
Filter 3800Hz/-6dB, 455kHz, AM. Impedance Zin = Zout = 2000 Ohm // 30pF.
Typical Inserti on Loss < 6dB. Col lins 7 pole Mechanical filter. For Coll ins
75S-3B/C
1 pc: 3 490 Kč
RoHS
INRAD-723 455kHz 7000Hz AM
GES08902162
INRAD 7000Hz/455kHz AM 8-pole Collins filter
1 pc: 2 790 Kč
RoHS
INRAD-803 FRONT END FILTER
10M
GES08901964
INRAD Front-end-filter 6 poles , 28025.0kHz, 50kHz/-1dB,
120kHz/-60dB, 50Ohm ., <0dB
Crystal filter CW 8999,3kHz / 250Hz, 8-pole. Shape factor 2,1. Impedance Zin
= Zout = 500 Ohms // 30pF. Typical Insertion Loss <9dB. Good for Yaesu
FT301, R-530 and for Experimenters.
Filter 7000Hz/-6dB, 455kHz, AM. Impedance Zin = Zout = 2000 Ohm //
30pF+560uH series. Typical Insertion Loss < 6dB. Colli ns 8 pole Mechanical
filter.
1 pc: 2 790 Kč
1 set: 3 190 Kč
RoHS
INRAD-2303 CW 9MHz FILTER
8999,3kHz 500Hz
GES08902166
Drake
INRAD CW crystal filter 8999,3kHz / 500Hz
Crystal filter CW 8999,3kHz / 500Hz, 8-pole. Shape factor 2,0. Impedance Zin
= Zout = 500 Ohms // 30pF. Typical Insertion Loss <7dB. Good for Yaesu
FT301, R-530 and for Experimenters.
INRAD-2600.2 DRAKE R4C
5695KHZ 125HZ CW
GES08902138
INRAD 125Hz/5695.0kHz DRAKE R4C for 2nd IF
1 set: 3 190 Kč
RoHS
INRAD-2304 CW 9MHz FILTER
9000kHz 500Hz
GES08902167
INRAD CW crystal filter 9000kHz / 500Hz
Crystal filter CW 9000kHz / 500Hz, 8-pole. Shape factor 2,0. Impedance Zi n =
Zout = 500 Ohms // 30pF. Typical Inserti on Loss <7dB. Good for
Experimenters.
1 set: 3 190 Kč
1 pc: 1 790 Kč
Action
RoHS
RoHS
INRAD-2308 SSB 9MHz FILTER
9000kHz 1800Hz
GES08902168
Crystal fil ter 125Hz/-6dB, 5695.0kHz, CW, 8 pole, Shape Factor 2.5. Fi lter is
soldered on custom PC board. Drop In. Ul timate rej ection >80dB. Ri pple
<2dB. Typi cal Insertion Loss: <9dB. Zin=Zout=50 Ohms. Dimensions:
57x24x21 mm.
1 pc: 3 190 Kč
INRAD SSB crystal filter 9000kHz / 1800Hz
Crystal filter CW 9000kHz / 1800Hz, 8-pol e. Shape factor 1,5. Impedance Zin
= Zout = 500 Ohms // 30pF. Typi cal Insertion Loss <6dB. Good for Yaesu FT7,
FT7B, FT301, R530 and for Experimenters.
9MHz
XTAL 8998.5kHz HC49/U
1 set: 3 190 Kč
GES08901972
Crystal USB carrier, tolerance 25°/+-50ppm (10-70°/+-100ppm),
Cl=30pF, HC49/U
RoHS
INRAD-2309 SSB 9MHz FILTER
9000kHz 2100Hz
RoHS
INRAD-2601.2 DRAKE R4C
5695KHZ 250HZ CW
GES08902139
INRAD 250Hz/5695.0kHz DRAKE R4C for 2nd IF
GES08902169
INRAD SSB crystal filter 9000kHz / 2100Hz
Crystal filter CW 9000kHz / 2100Hz, 8-pol e. Shape factor 1,5. Impedance Zin
= Zout = 500 Ohms // 30pF. Typi cal Insertion Loss <6dB. Good for Yaesu FT7,
FT7B, FT301, R530 and for Experimenters.
1 set: 3 190 Kč
RoHS
1 pc: 325.00 Kč
RoHS
XTAL 9000.0kHz HC49/U
GES08901973
Crystal CW carrier, tolerance 25°/+-50ppm (10-70°/+-100ppm),
Cl=30pF, HC49/U
1 pc: 325.00 Kč
RoHS
XTAL 9001.5kHz HC49/U
GES08901974
Crystal LSB carrier, tolerance 25°/+-50ppm (10-70°/+-100ppm),
Cl=30pF, HC49/U
1 pc: 325.00 Kč
RoHS
INRAD-2310 SSB 9MHz FILTER
9000kHz 2400Hz
GES08902170
INRAD SSB crystal filter 9000kHz / 2400Hz
Crystal filter CW 9000kHz / 2400Hz, 8-pol e. Shape factor 1,5. Impedance Zin
= Zout = 500 Ohms // 30pF. Typi cal Insertion Loss <6dB. Good for Yaesu FT7,
FT7B, FT301, R530 and for Experimenters.
1 set: 3 190 Kč
RoHS
INRAD-2311 AM 9MHz FILTER
9000kHz 6000Hz
GES08902171
1 pc: 3 190 Kč
RoHS
INRAD AM crystal filter 9000kHz / 6000Hz
Crystal filter AM 9000kHz / 6000Hz, 8-pol e. Shape factor 1,5. Impedance Zin
= Zout = 500 Ohms // 30pF. Typical Insertion Loss <6dB. Good for Sienna,
Yaesu FT 7B, FT 301, R530 and for Experimenters.
1 set: 3 190 Kč
RoHS
Crystal fil ter 250Hz/-6dB, 5695.0kHz, CW, 8 pole, Shape Factor 1.9. Fi lter is
soldered on custom PC board. Drop In. Ul timate rej ection >80dB. Ri pple
<2dB. Typi cal Insertion Loss: <9dB. Zin=Zout=50 Ohms. Dimensions:
57x24x21 mm.
INRAD-2603.2 DRAKE R4C
5695KHZ 500HZ CW
GES08901826
INRAD 500Hz/5695.0kHz DRAKE R4C for 2nd IF
INRAD-2612.1 DRAKE R4C
5645KHZ 8000HZ GUF1
GES08902142
INRAD 8000Hz/5645.0kHz DRAKE R4C for 1st IF
Crystal fi lter 500Hz/-6dB, 5695.0kHz, CW, 8 pole, Shape Factor 1.9. Filter i s
soldered on custom PC board. Drop In. Ultimate rejecti on >80dB. Ripple
<2dB. Typical Inserti on Loss: <7dB. Zi n=Zout=50 Ohms. Dimensions:
57x24x21 mm.
INRAD-2608.2 DRAKE R4C
5695KHZ 1800HZ SSB
GES08902136
Crystal filter 8000Hz/-6dB, 5645.0kHz, GUF-1, 8 pol e, Shape Factor 1.7.
Ulti mate rejecti on >80dB. Ri pple <2dB. Typical Insertion Loss: <6dB.
Zin=Zout=1000 Ohms. Di mensi ons: 40x20x21 mm. This fi lter (also known as
GUF-1) i s a superior repl acement for the ori ginal 4-pole uni t in the Drake
R-4C. Exceptional i mprovement. Install ati on requires dri lling three small
holes in the radi o chassis.
1 pc: 3 190 Kč
RoHS
Crystal fi lter 8-pole. 1800Hz/-6dB, 8215kHz, SSB, shape factor 1,5. Typický
Insertion Loss <5dB. Filter i s sol dered on custom PC board. Plug in.
1 pc: 3 490 Kč
RoHS
INRAD-709 ELECRAFT KFL3A-2.1K
8215KHZ 2100HZ SSB
Elecraft
INRAD-708 ELECRAFT KFL3A-250
8215KHZ 250HZ CW
INRAD 1800Hz/5695.0kHz DRAKE R4C for 2nd IF
GES08902147
INRAD 1800Hz/8215kHz. ELECRAFT KFL3A-1.8K
1 pc: 3 190 Kč
RoHS
INRAD-711 ELECRAFT KFL3A-1.8K
8215KHZ 1800HZ SSB
GES08902143
GES08902148
INRAD 2100Hz/8215kHz. ELECRAFT KFL3A-2.1K
INRAD 250Hz/8215kHz. ELECRAFT KFL3A-250
Crystal fi lter 1800Hz/-6dB, 5695.0kHz, SSB, 8 pole, Shape Factor 1.7. Filter i s
soldered on custom PC board. Drop In. Ultimate rejecti on >80dB. Ripple
<2dB. Typical Inserti on Loss: <6dB. Zi n=Zout=50 Ohms. Dimensions:
57x24x21 mm.
1 pc: 3 190 Kč
RoHS
INRAD-2609.2 DRAKE R4C
5695KHZ 2100HZ SSB
Crystal fi lter 8-pole. 2100Hz/-6dB, 8215kHz, SSB, shape factor 1,5. Typical
Insertion Loss <6dB. Filter i s sol dered on custom PC board. Plug in. .
GES08902137
1 pc: 3 490 Kč
RoHS
INRAD 2100Hz/5695.0kHz DRAKE R4C for 2nd IF
Crystal filter 8-pol e. 250Hz/-6dB, 8215kHz, CW, shape factor 2.1. Typical
Inserti on Loss <9dB. Filter is soldered on custom PC board. Pl ug in. .
INRAD-716 ELECRAFT KFL3A-2.8K
8215KHZ 2800HZ SSB
GES08902149
INRAD 2800Hz/8215kHz. ELECRAFT KFL3A-2.8K
1 pc: 3 490 Kč
RoHS
INRAD-701 ELECRAFT KFL3A-400
8215KHZ 400HZ CW
GES08902144
INRAD 400Hz/8215kHz. ELECRAFT KFL3A-400
Crystal fi lter 2100Hz/-6dB, 5695.0kHz, SSB, 8 pole, Shape Factor 1.7. Filter i s
soldered on custom PC board. Drop In. Ultimate rejecti on >80dB. Ripple
<2dB. Typical Inserti on Loss: <6dB. Zi n=Zout=50 Ohms. Dimensions:
57x24x21 mm.
1 pc: 3 190 Kč
RoHS
INRAD-2611.1 DRAKE R4C
5645KHZ 6000HZ GUF1
GES08902141
INRAD 6000Hz/5645.0kHz DRAKE R4C for 1st IF
Crystal fi lter 8-pole. 2800Hz/-6dB, 8215kHz, SSB, shape factor 1,5. Typical
Insertion Loss <6dB. Filter i s sol dered on custom PC board. Plug in. .
Crystal fil ter 6000Hz/-6dB, 5645.0kHz, GUF-1, 8 pol e, Shape Factor 1.7.
Ulti mate rejection >80dB. Ripple <2dB. Typical Insertion Loss: <6dB.
Zin=Zout=1000 Ohms. Di mensi ons: 40x20x21 mm. This fi lter (also known as
GUF-1) i s a superior repl acement for the origi nal 4-pole uni t in the Drake
R-4C. Exceptional i mprovement. Instal lation requires drilli ng three small
holes in the radi o chassis.
1 pc: 3 190 Kč
RoHS
INRAD-2611.2 DRAKE R4C
5695KHZ 6000HZ AM
1 pc: 3 190 Kč
RoHS
Crystal filter 8-pol e. 400Hz/-6dB, 8215kHz, CW, shape factor 2.1. Typical
Inserti on Loss <8dB. Filter is soldered on custom PC board. Pl ug in. .
GES08902140
INRAD-710 ELECRAFT KFL3A-6K
8215KHZ 6000HZ AM
GES08902150
INRAD 6000Hz/8215kHz. ELECRAFT KFL3A-6K
1 pc: 3 190 Kč
RoHS
INRAD 6000Hz/5695.0kHz DRAKE R4C for 2nd IF
INRAD-728 ELECRAFT KFL3A-500
8215KHZ 500HZ CW
GES08902145
INRAD 500Hz/8215kHz. ELECRAFT KFL3A-500
Crystal filter 8-pol e. 500Hz/-6dB, 8215kHz, CW, shape factor 2.1. Typical
Inserti on Loss <7dB. Filter is soldered on custom PC board. Pl ug in. .
1 pc: 3 190 Kč
INRAD-718 ELECRAFT KFL3A-1.0K
8215KHZ 1000HZ CW
GES08902146
INRAD 1000Hz/8215kHz. ELECRAFT KFL3A-1.0K
Crystal fi lter 8-pol e. 6000Hz/-6dB, 8215kHz, AM, shape factor 1,5. Typical
Insertion Loss <6dB. Filter i s sol dered on custom PC board. Plug in. .
1 pc: 3 490 Kč
RoHS
Crystal fil ter 6000Hz/-6dB, 5695.0kHz, AM, 8 pole, Shape Factor 1.7. Filter i s
soldered on custom PC board. Drop In. Ultimate rejecti on >80dB. Ripple
<2dB. Typical Inserti on Loss: <6dB. Zi n=Zout=50 Ohms. Dimensions:
57x24x21 mm.
INRAD-725 ELECRAFT KFL3B-FM
8215KHZ 13000HZ FM
GES08902151
INRAD 13000Hz/8215kHz. ELECRAFT KFL3A-FM
1 pc: 3 190 Kč
Crystal fi lter 8-pole. 13000Hz/-6dB, 8215kHz, FM, shape factor 1,5. Typical
Insertion Loss <6dB. Filter i s sol dered on custom PC board. Plug in. .
RoHS
1 pc: 3 190 Kč
Crystal fil ter 8-pol e. 1000Hz/-6dB, 8215kHz, CW, shape factor 2.1. Typical
Inserti on Loss <7dB. Filter is soldered on custom PC board. Pl ug in. .
1 pc: 3 190 Kč
RoHS
INRAD-111 ICOM 9010,6kHz 400Hz
CW
Icom
INRAD-306 ICOM 455kHz 125Hz CW
GES08900195
INRAD-314 ICOM 455kHz 2100Hz
SSB
GES08900199
INRAD 400Hz/9010.6kHz ICOM
INRAD 2100Hz/455kHz ICOM
For R70, R71, R75, R7000, IC701, IC720A, IC725, IC726, IC728, IC729,
IC735, IC736, IC737, R70, R71, R75, R7000, IC701, IC720A, IC725, IC726,
IC728, IC729, IC735, IC736, IC737, IC738, IC746, IC751, IC751A, IC756,
IC761, IC765, IC775, IC781. Better approximated replace for origi nal ICOM
FL-100 (FL100 has bandwidth 500Hz) or for FL-32 (FL32 has bandwidth
500Hz and shape factor only 3.2). Crystal filter 8-pole. 400Hz/-6dB,
9010.6kHz, CW, Shape Factor 2.2. Fil ter i s soldered on custom PC board and
is wi red at place. Ul timate rejection >90dB. Ri pple <2dB. Typical Inserti on
Loss: <8dB. Zin=Zout=2000Ohms. Di mensi ons: 40x18x20 mm.
For IC718, IC735, IC736, IC737, IC738, IC740, IC745, IC746, IC751, IC751A,
IC756, IC761, IC765, IC775, IC781. Filter 2100Hz/-6dB, 455kHz, SSB, Shape
Factor 1.6. Fi lter i s soldered on custom PC board. Drop In (Wi re In for IC735).
Ultimate rejecti on >90dB. Ri pple <2dB. Typical Insertion Loss: <5dB.
Zin=Zout=2000Ohms. Di mensi ons: 55x25x15 mm.
GES08900191
INRAD 125Hz/455k ICOM
For IC740, IC745, IC756, IC761, IC765, IC775, IC781. Filter 125Hz/-6dB,
455kHz, CW, Shape Factor 1.8. Filter is soldered on custom PC board and i s
wired at place. Ulti mate rejecti on >90dB. Ripple <2dB. Typical Insertion Loss:
<8dB. Zi n=Zout=2000Ohms. Dimensions: 55x25x15 mm.
1 pc: 4 190 Kč
RoHS
INRAD-122 ICOM 455kHz 250Hz CW
1 pc: 2 790 Kč
RoHS
GES08900192
INRAD 250Hz/455k ICOM
INRAD-112 ICOM 9011,5kHz 400Hz
CW IC 730, IC740, IC745
GES08900196
1 pc: 4 190 Kč
RoHS
INRAD-110 ICOM 9011,5kHz 2100Hz
SSB
GES08900200
INRAD 2100Hz/9011.5kHz ICOM
INRAD 400Hz/9011.5kHz ICOM
For IC730, IC740, IC745. Crystal filter 8-pol e. 400Hz/-6dB, 9011.5kHz, CW,
Shape Factor 2.8. Fil ter is soldered on custom PC board and i s wired at
place. Ultimate rejection >90dB. Ripple <2dB. Typical Insertion Loss: <7dB.
Zin=Zout=2000Ohms. Dimensions: 40x18x20 mm.
For IC703, IC707, IC718, IC736, IC737, IC738, IC740, IC745, IC746, IC751,
IC751A, IC756, IC761, IC765, IC775, IC781, R8500. Better replace for
ori ginal ICOM FL53A. Crystal fil ter 8-pol e. 250Hz/-6dB, 455kHz, CW, Shape
Factor 1.8. Filter i s soldered on custom PC board. Drop In. Ultimate rejecti on
>90dB. Ripple <2dB. Typical Insertion Loss: <8dB. Zin=Zout=2000Ohms.
Dimensions: 55x25x15 mm.
1 pc: 4 190 Kč
RoHS
INRAD-121 ICOM 9010,6kHz 250Hz
CW
GES08900193
1 pc: 2 790 Kč
RoHS
INRAD-115 ICOM 10749,3kHz 400Hz
CW IC271, IC471, IC1271
GES08901630
For ICOM IC735, IC736, IC737, IC738, IC740, IC745, IC746, IC751, IC751A,
IC756, IC761, IC765, IC775, IC781. Crystal filter 8-pol e. 2100Hz/-6dB,
9011.5kHz, SSB, Shape Factor 1.6. Filter is soldered on custom PC board and
i s wired at pl ace. Ultimate rejection >90dB. Rippl e <2dB. Typi cal Insertion
Loss: <5dB. Zin=Zout=2000Ohms. Dimensions: 40x18x20 mm.
1 pc: 2 790 Kč
RoHS
INRAD 400Hz/10749.3kHz ICOM
For IC271, IC471, IC1271. Crystal fil ter 8-pol e. 400Hz/-6dB, 10749.3kHz, CW,
Shape Factor 3.0. Fil ter is soldered on custom PC board and i s wired at
place. Ultimate rejection >90dB. Ripple <2dB. Typical Insertion Loss: <6dB.
Zin=Zout=2000Ohms.
1 pc: 2 790 Kč
INRAD-113 ICOM 10750kHz 2100Hz
SSB IC271, IC471, IC1271, IC701,
IC720
GES08901629
INRAD 2100Hz/10750kHz ICOM
RoHS
INRAD 250Hz/9010.6kHz ICOM
INRAD-322 ICOM 455kHz 1800Hz
SSB
GES08900197
INRAD 1800Hz/455kHz ICOM
For IC271, IC471, IC1271, IC701, IC720. Crystal filter 8-pole. 2100Hz/-6dB,
10750kHz, SSB, Shape Factor 1.6. Filter is soldered on custom PC board and
i s wired at pl ace. Ultimate rejection >90dB. Rippl e <2dB. Typi cal Insertion
Loss: <5dB. Zin=Zout=2000Ohms.
1 pc: 2 790 Kč
RoHS
For R70, R71, R75, R7000, IC701, IC720A, IC725, IC726, IC728, IC729,
IC735, IC736, IC737, IC738, IC746, IC751, IC751A, IC756, IC761, IC765,
IC775, IC781. Better replace for original ICOM FL-101. Crystal fi lter 8-pole.
250Hz/-6dB, 9010.6kHz, CW, Shape Factor 2.2. Fil ter i s soldered on custom
PC board and i s wired at place. Ultimate rej ection >90dB. Ripple <2dB.
Typi cal Insertion Loss: <8dB. Zin=Zout=2000Ohms. Di mensi ons: 40x18x20
mm.
1 pc: 1 490 Kč
Action
RoHS
INRAD-116 ICOM 455KHz 400Hz CW
GES08900194
INRAD 400Hz/455k ICOM
INRAD-109 ICOM 455kHz 2400Hz
SSB
GES08900201
INRAD 2400Hz/455kHz ICOM
For IC718, IC735, IC736, IC737, IC738, IC740, IC745, IC746, IC751, IC751A,
IC756, IC761, IC765, IC775, IC781. Filter 1800Hz/-6dB, 455kHz, SSB, Shape
Factor 1.5. Fi lter is soldered on custom PC board. Drop In (Wi re In for IC735).
Ulti mate rejecti on >90dB. Ri pple <2dB. Typical Insertion Loss: <5dB.
Zin=Zout=2000Ohms. Dimensions: 55x25x15 mm. Better approxi mate
replace for original ICOM FL-222 (1900Hz).
1 pc: 4 190 Kč
RoHS
INRAD-320 ICOM 9011,5kHz 1800Hz
SSB
GES08900198
INRAD1800Hz/9011.5kHz ICOM
For ICOM IC718, IC735, IC736, IC737, IC738, IC740, IC745, IC746, IC751,
IC751A, IC756, IC761, IC765, IC775, IC781. Crystal filter 8-pol e.
2400Hz/-6dB, 455kHz, SSB, Shape Factor 1.6. Fi lter is sol dered on custom
PC board. Drop In (Wire in for IC735). Ultimate rejection >90dB. Rippl e <2dB.
Typical Insertion Loss: <5dB. Zin=Zout=2000Ohms. Dimensions: 55x25x15
mm.
1 pc: 4 190 Kč
RoHS
For IC703, IC707, IC718, IC736, IC737, IC738, IC740, IC745, IC746, IC751,
IC751A, IC756, IC761, IC765, IC775, IC781, R70, R71, R75, R7000, R8500.
Crystal filter 8-pole. 400Hz/-6dB, 455kHz, CW, Shape Factor 1.8. Filter i s
soldered on custom PC board. Drop In. Ultimate rejecti on >90dB. Ripple
<2dB. Typical Insertion Loss: <7dB. Zi n=Zout=2000Ohms. Dimensions:
55x25x15 mm. Much better stopband, less ripple and better shape factor than
ori ginal FL52A (500Hz, 455kHz).
1 pc: 4 190 Kč
RoHS
For IC735, IC736, IC737, IC738, IC740, IC745, IC746, IC751, IC751A, IC756,
IC761, IC765, IC775, IC781. Fi lter 1800Hz/-6dB, 9011.5kHz, SSB, Shape
Factor 1.8. Filter is soldered on custom PC board and is wired at pl ace.
Ulti mate rejecti on >90dB. Ri pple <2dB. Typical Insertion Loss: <5dB.
Zin=Zout=2000Ohms. Dimensions: 40x18x20 mm. Better approxi mate
replace for original ICOM FL-223 (bandwidth 1900Hz).
1 pc: 2 790 Kč
RoHS
INRAD-124 ICOM 455kHz 2800Hz
SSB
GES08900202
INRAD 2800Hz/455kHz ICOM
INRAD-909 ICOM 64,4550MHZ
ROOFING FILTER
GES08902081
INRAD VHF Bare Filter 64,4550MHz (>4kHz, 6 poles, 50 Ohms)
INRAD-22 KENWOOD 8830kHz
250Hz CW TS450, TS570, TS690,
TS850, TS930, TS940, TS950
GES08900208
INRAD 250Hz/8830kHz. KENWOOD TS450, TS570, TS690, TS850,
TS930, TS940, TS950
For mai n RX IC745, IC756PROI, IC756PROII, IC756PROIII
1 pc: 2 990 Kč
RoHS
INRAD-911 ICOM 69,0115MHZ
ROOFING FILTER
For IC718, IC735, IC736, IC737, IC738, IC740, IC745, IC746, IC751, IC751A,
IC756, IC761, IC765, IC775, IC781. Crystal fil ter 8-pole. 2800Hz/-6dB,
455kHz, SSB, Shape Factor 1.5. Filter is soldered on custom PC board. Drop
In (Wire In for IC735). Ul timate rej ection >90dB. Rippl e <2dB. Typical
Inserti on Loss: <5dB. Zin=Zout=2000Ohms. Dimensions: 55x25x15 mm.
1 pc: 4 190 Kč
RoHS
INRAD-IC781 ICOM 46.5115MHZ
ROOFING FILTER
GES08902119
INRAD Roofing Filter 46.5115MHz/4-5kHz/6poles, w.High Dynamic
Amplifier, for IC781 Icom
The Icom IC-781 roofing fi lter mod consists of a 6-pole, 4 to 5 kHz wi de fil ter
fol lowed by a high dynamic range, feedback amplifi er. The ampl ifier provi des
enough gain to override the fi lter i nsertion loss. The IMD dynamic range will
be improved 7 to 14 dB for some signal spacings. The mai n recei ver audio
response wi ll be reduced about 100 Hz i n the SSB mode. Operati ng the
noise bl anker wi ll not result in as much degradation of the dynamic range.
The mod i nserts a narrow band crystal filter in between the pin attenuator
fol lowing the first mixer and the grounded gate first IF amplifier. Reducing the
bandwidth at this point i n the radi o helps to keep strong off-frequency signal s
out of the second mixer where they can cause i ntermodul ati on. Transmissi on
is not changed as i t does not pass through the roofing filter.
1 pc: 4 890 Kč
GES08902082
INRAD VHF Bare Filter 69,0115MHz (>4kHz, 6 poles, 50 Ohms).
For m ain RX IC756, IC765, IC775.
1 pc: 2 990 Kč
RoHS
INRAD-913 ICOM IC761 70,4515MHZ
ROOFING FILTER
GES08902083
Filter 250Hz/-6dB, 8830kHz, CW, Shape Factor 2.3. Ultimate rejection >90dB.
Ripple <2dB. Typical Insertion Loss: <8dB. Dimensions: 50x18x18 mm. Filter
soldered on custom PC board. Better replace for original YK88CN1 (270Hz).
1 pc: 3 090 Kč
INRAD VHF Bare Filter 70,4515MHz (>4kHz, 6 poles, 50 Ohms) for
main RX IC761
1 pc: 2 990 Kč
RoHS
INRAD-97 KENWOOD 8830.7kHz
250Hz CW TS430, TS440
GES08901936
INRAD 250Hz/8830.7kHz KENWOOD TS430, TS440
RoHS
Kenwood
INRAD-306 KENWOOD 455kHz
125Hz CW TS140, TS680, TS850,
TS930, TS940, TS950, R2000
GES08900203
INRAD 125Hz/455kHz. KENWOOD TS140, TS680, TS850, TS930,
TS940, TS950, R2000
RoHS
INRAD-IC756PROII ICOM
64.4550MHZ ROOFING FILTER
GES08902043
INRAD Roofing Filter 64.4550MHz/6poles, w.High Dynamic
Amplifier, for IC756PROII Icom
Thi s Roofi ng Fi lter works wi th IC756PROII model onl y and hel p to reduce the
thi rd order IM products from multipl e strong signal s i n the 2 to 20kHz regi on
either side of the tuned frequency. IMD dynami c range wi ll be improved 10dB
or more for some signal spaci ng. Filter is assembled on PCB with Hi gh
Dynami c Range Feedback Amplifier, which cover the Filter loss plus a dB or
two. Thi s mod is si gnificantl y more chal lengi ng to perform than other INRAD
roofing fil ters and requires removal of some SMT components and other
speci al knowl edges. It should be performed by those with consi redable
technical skil ls. GES-ELECT RONICS can do i t - contact us please for details.
Filter 250Hz/-6dB, 8830.7kHz, CW, Shape Factor 2.8. Inrad fil ter is much
l arger than mfgr's fi lter. Wire i n. Ultimate rej ection >90dB. Ri pple <2dB.
Typical Insertion Loss: <8dB. Zi n=Zout=2000 Ohms. Dimensions: 50x18x18
mm.
1 pc: 3 090 Kč
RoHS
INRAD-104 KENWOOD 455kHz
400Hz CW R2000
1 pc: 3 490 Kč
Action
RoHS
INRAD-IC756PROIII ICOM
64.4550MHZ ROOFING FILTER
GES08902044
INRAD Roofing Filter 64.4550MHz/6poles, w.High Dynamic
Amplifier, for IC756PROIII Icom
Thi s Roofi ng Fi lter works with IC756PROIII model only and help to reduce the
thi rd order IM products from multipl e strong signal s i n the 2 to 20kHz regi on
either side of the tuned frequency. IMD dynami c range wi ll be improved 10dB
or more for some signal spaci ng. Filter is assembled on PCB with Hi gh
Dynami c Range Feedback Amplifier, which cover the Filter loss plus a dB or
two. Thi s mod is si gnificantl y more chal lengi ng to perform than other INRAD
roofing fil ters and requires removal of some SMT components and other
speci al knowl edges. It should be performed by those with consi redable
technical skil ls. GES-ELECT RONICS can do i t - contact us please for details.
1 pc: 4 890 Kč
RoHS
INRAD-IC765 ICOM 69.0115MHZ
ROOFING FILTER
GES08901845
Fil ter 125Hz/-6dB, 455kHz, CW, Shape Factor 2.1. Fil ter is soldered on custom
PC board. Ultimate rejecti on >90dB. Rippl e <2dB. Typical Insertion Loss:
<8dB. Dimensions: 64x24x22 mm.
GES08901941
INRAD 400Hz/455kHz KENWOOD R2000
1 pc: 4 190 Kč
RoHS
INRAD-306 KENWOOD 455kHz
125Hz CW TS450S, TS690
GES08900204
INRAD 125Hz/455kHz KENWOOD TS450S, TS690
Fil ter 125Hz/-6dB, 455kHz, CW, Shape Factor 1.8. Ultimate rejection >90dB.
Ripple <2dB. Typical Insertion Loss: <8dB. Zin=Zout=2000Ohms. Dimensions:
64x24x22 mm. Drop in exact repl acement.
1 pc: 4 190 Kč
RoHS
INRAD-186 KENWOOD 455kHz
250Hz CW TS450S, TS690
GES08900206
INRAD 250Hz/455kHz KENWOOD TS450S, TS690, R2000
INRAD Roofing Filter 69.0115MHz/6poles, w.High Dynamic
Amplifier, for IC765 Icom
Crystal filter 8-pole. 400Hz/-6dB, 455kHz, CW, Shape Factor 1.8. Ultimate
rejection >90dB. Ripple <2dB. Typical Inserti on Loss: <7dB. Zin=Zout=2000
Ohms. Dimensions: 64x24x22 mm. Wi re in filter; required sol dering short
pigtai ls or miniature coax.
1 pc: 4 190 Kč
RoHS
INRAD-104 KENWOOD 455kHz
400Hz CW TS140, TS680, R2000
GES08900209
INRAD 400Hz/455kHz KENWOOD TS140, TS680, R2000
Crystal filter 8-pole. 400Hz/-6dB, 455kHz, CW, Shape Factor 1.7. Ultimate
rejection >90dB. Ripple <2dB. Typical Inserti on Loss: <7dB. Zin=Zout=2000
Ohms. Di mensi ons: 64x24x22 mm. Fi lter soldered on custom PC board.
Thi s Roofing Fil ter hel p to reduce the thi rd order IM products from multiple
strong signals in the 2 to 20kHz region either si de of the tuned frequency. IMD
dynamic range will be improved 10dB or more for some signal spacing. Fil ter
is assembled on PCB wi th High Dynamic Range Feedback Amplifi er, which
cover the Filter l oss plus a dB or two.
1 pc: 4 290 Kč
RoHS
INRAD-IC775 ICOM 69.0115MHZ
ROOFING FILTER
GES08901846
INRAD Roofing Filter 69.0115MHz/6poles, w.High Dynamic
Amplifier, for IC775 Icom
1 pc: 4 290 Kč
RoHS
INRAD-905 ICOM 46,5115MHZ
ROOFING FILTER
GES08902084
1 pc: 4 190 Kč
RoHS
INRAD-104 KENWOOD 455kHz
400Hz CW TS450S, TS690
Crystal fil ter 8-pol e. 250Hz/-6dB, 455kHz, CW, Shape Factor 2.0. Ulti mate
rej ection
>90dB.
Ripple
<2dB.
Typical
Insertion
Loss:
<8dB.
Zin=Zout=2000Ohms. Dimensions: 64x24x22 mm. Drop in exact
replacement. Wire in for R2000. Better filter than origi nal YG455CN1
(=YK455CN1).
INRAD-186 KENWOOD 455kHz
250Hz CW TS850, TS930, TS940,
TS950
GES08900205
INRAD 250Hz/455kHz. KENWOOD TS850, TS930, TS940, TS950
INRAD VHF Bare Filter 46,5115MHz (>4kHz, 6 poles, 50 Ohms) for
main RX IC781
1 pc: 2 990 Kč
INRAD 400Hz/455kHz KENWOOD TS450S, TS690
Crystal filter 8-pole. 400Hz/-6dB, 455kHz, CW, Shape Factor 1.7. Ultimate
rejection
>90dB.
Ri pple
<2dB.
Typical
Inserti on
Loss:
<7dB.
Zin=Zout=2000Ohms. Di mensi ons: 64x24x22 mm. Drop in exact
replacement.
1 pc: 2 890 Kč
Action
RoHS
Fil ter 250Hz/-6dB, 455kHz, CW, Shape Factor 2.0. Fil ter is soldered on custom
PC board. Ultimate rejecti on >90dB. Rippl e <2dB. Typical Insertion Loss:
<8dB. Dimensions: 64x24x22 mm. Better filter than origi nal YG455CN1
(=YK455CN1).
RoHS
1 pc: 4 190 Kč
RoHS
GES08900210
1 pc: 4 190 Kč
RoHS
INRAD-104 KENWOOD 455kHz
400Hz CW TS850, TS930, TS940,
TS950
GES08900211
INRAD 400Hz/455kHz KENWOOD TS850, TS930, TS940, TS950
Crystal filter 8-pole. 400Hz/-6dB, 455kHz, CW, Shape Factor 1.7. Ultimate
rejection >90dB. Ripple <2dB. Typical Insertion Loss: <7dB. Dimensions:
64x24x22 mm. Filter soldered on custom PC board.
1 pc: 4 190 Kč
RoHS
INRAD-103 KENWOOD 8830kHz
400Hz CW TS450S, TS690
GES08900212
INRAD 400Hz/8830kHz KENWOOD TS450S, TS690
INRAD-528 KENWOOD 455kHz
500Hz CW TS850, TS930, TS940,
TS950
GES08900216
INRAD 500Hz/455kHz KENWOOD TS850, TS930, TS940, TS950
Fil ter 500Hz/-6dB, 455kHz, CW, Shape Factor 1.7. Ultimate rejection >90dB.
Ripple <2dB. Typical Insertion Loss: <7dB. Dimensions: 64x24x22 mm. Fil ter
soldered on custom PC board. Repl ace the YG455C1 (=YK455C1) Kenwood
filter.
INRAD-96 KENWOOD 455kHz
2100Hz SSB TS140, TS440, TS680,
TS930, TS940
GES08900222
INRAD 2100Hz/455kHz KENWOOD TS140, TS440, TS680, TS930,
TS940
1 pc: 4 190 Kč
RoHS
INRAD-93 KENWOOD 455kHz
1800Hz SSB TS140, TS440, TS680,
R2000
GES08900217
INRAD 1800Hz/455kHz KENWOOD R2000, TS140, TS440, TS680
Crystal filter 8-pol e. 400Hz/-6dB, 8830kHz, CW, Shape Factor 2.5. Ulti mate
rej ection
>90dB.
Ripple
<2dB.
Typical
Insertion
Loss:
<7dB.
Zin=Zout=2000Ohms. Dimensions: 50x18x18 mm. Drop in exact
replacement.
Filter 2100Hz/-6dB, 455kHz, SSB, Shape Factor 1.5. Inrad filter is much
l arger than mfgr's fi lter. Wire i n. Ultimate rej ection >90dB. Ri pple <2dB.
Typical Insertion Loss: <5dB. Zin=Zout=2000Ohms. Dimensions: 64x24x22
mm.
1 pc: 1 990 Kč
Action
RoHS
INRAD-103 KENWOOD 8830kHz
400Hz CW TS570
GES08901635
1 pc: 4 190 Kč
RoHS
INRAD-96 KENWOOD 455kHz
2100Hz SSB TS450S, TS690
INRAD 400Hz/8830kHz KENWOOD TS570
Crystal filter 8-pol e. 400Hz/-6dB, 8830kHz, CW, Shape Factor 2.1. Ulti mate
rej ection >90dB. Rippl e <2dB. Typical Insertion Loss: <7dB. Dimensions:
50x18x18 mm. Filter soldered on custom PC board. Better replace for ori ginal
YK88C1 (500Hz).
1 pc: 3 090 Kč
RoHS
INRAD-103 KENWOOD 8830kHz
400Hz CW TS930, TS940, TS950
GES08900213
INRAD 2100Hz/455kHz KENWOOD TS440, TS450S, TS690
Fil ter 1800Hz/-6dB, 455kHz, SSB, Shape Factor 1.5. Inrad fil ter is much
larger than mfgr's fi lter. Wi re i n. Ulti mate rej ection >90dB. Ri pple <2dB.
Typi cal Insertion Loss: <5dB. Zin=Zout=2000Ohms. Di mensi ons: 64x24x22
mm.
1 pc: 4 190 Kč
RoHS
INRAD 400Hz/8830kHz KENWOOD TS850, TS930, TS940, TS950
Crystal filter 8-pol e. 400Hz/-6dB, 8830kHz, CW, Shape Factor 2.1. Ulti mate
rej ection >90dB. Rippl e <2dB. Typical Insertion Loss: <7dB. Dimensions:
50x18x18 mm. Filter soldered on custom PC board.
1 pc: 1 890 Kč
Action
RoHS
INRAD-98 KENWOOD 8830.7kHz
400Hz CW TS430, TS440
GES08901937
INRAD-93 KENWOOD 455kHz
1800Hz SSB TS450S, TS690
GES08900218
Filter 2100Hz/-6dB, 455kHz, SSB, Shape Factor 1.5. Ultimate rej ection
>90dB. Ripple <2dB. Typical Insertion Loss: <5dB. Zin=Zout=2000 Ohms.
Dimensions: 64x24x22 mm. Drop in exact replacement.
1 pc: 4 190 Kč
RoHS
INRAD-96 KENWOOD 455kHz
2100Hz SSB TS850, TS950
GES08900224
INRAD 2100Hz/455kHz KENWOOD TS850, TS950
INRAD 1800Hz/455kHz KENWOOD TS450S, TS690
Fil ter 1800Hz/-6dB, 455kHz, SSB, Shape Factor 1.5. Ulti mate rejecti on
>90dB. Ripple <2dB. Typical Insertion Loss: <5dB. Zin=Zout=2000Ohms.
Dimensions: 64x24x22 mm. Drop in exact repl acement.
1 pc: 4 190 Kč
RoHS
INRAD-93 KENWOOD 455kHz
1800Hz SSB TS850, TS950
INRAD 400Hz/8830.7kHz KENWOOD TS430, TS440
GES08900223
GES08900219
Filter 2100Hz/-6dB, 455kHz, SSB, Shape Factor 1.5. Ultimate rej ection
>90dB. Ri pple <2dB. Typi cal Insertion Loss: <5dB. Dimensions: 64x24x22
mm. Filter soldered on custom PC board.
1 pc: 4 190 Kč
RoHS
INRAD-96 KENWOOD 455kHz
2100Hz SSB TS870
GES08901939
INRAD 2100Hz/455kHz KENWOOD TS870
INRAD 1800Hz/455kHz KENWOOD TS850, TS950
Fil ter 1800Hz/-6dB, 455kHz, SSB, Shape Factor 1.5. Ulti mate rejecti on
>90dB. Ri pple <2dB. Typi cal Insertion Loss: <5dB. Di mensi ons: 64x24x22
mm. Fil ter sol dered on custom PC board.
1 pc: 4 190 Kč
RoHS
GES08901935
INRAD-95 KENWOOD 8830kHz
1800Hz SSB R820, R5000, TS120,
TS130, TS180, TS430, TS440, TS530, TS820
INRAD 1800Hz/8830kHz. KENWOOD R820, R5000, TS120,
TS130, TS180, TS430, TS440, TS530, TS820
Filter 2100Hz/-6dB, 455kHz, SSB, Shape Factor 1.5. Inrad filter is wired in
with mini coax. Ultimate rejection >90dB. Rippl e <2dB. Typi cal Insertion
Loss: <5dB. Di mensi ons: 64x24x22 mm.
1 pc: 4 190 Kč
RoHS
INRAD-94 KENWOOD 8830kHz
2100Hz SSB TS120, TS130, TS430,
TS440, TS830, TS870, TS930, TS940
GES08900227
INRAD 2100Hz/8830kHz. KENWOOD TS120, TS130, TS430,
TS440, TS830, TS870, TS930, TS940
Fil ter 400Hz/-6dB, 8830.7kHz, CW, Shape Factor 2.5. Inrad fi lter is much
larger than mfgr's filter. Wi re in. Ulti mate rejecti on >90dB. Ripple <2dB.
Typi cal Insertion Loss: <7dB. Zin=Zout=2000 Ohms. Di mensi ons: 50x18x18
mm.
1 pc: 3 090 Kč
Filter 2100Hz/-6dB, 8830kHz, SSB, Shape Factor 1.5. Ul timate rej ection
>90dB. Ripple <2dB. Typical Insertion Loss: <5dB. Zi n=Zout=2000Ohms.
Dimensions: 50x18x18 mm. Wi re in fil ter; requires solderi ng short pi gtails or
miniature coax. Al so good for R820, R5000, T S180, TS530, TS820. Better
replace for original YK-88SN1.
RoHS
INRAD-528 KENWOOD 455kHz
500Hz CW R2000
GES08901942
INRAD 500Hz/455kHz CW KENWOOD R2000
1 pc: 3 090 Kč
RoHS
Fil ter 1800Hz/-6dB, 8830kHz, SSB, Shape Factor 1.5. Ultimate rejecti on
>90dB. Ripple <2dB. Typical Insertion Loss: <5dB. Zin=Zout=2000Ohms.
Dimensions: 50x18x18 mm. Wi re in fil ter; requires solderi ng short pi gtails or
mi niature coax.
1 pc: 3 090 Kč
RoHS
INRAD-95 KENWOOD 8830kHz
1800Hz SSB TS450, TS570, TS690,
TS850, TS950
GES08900221
INRAD 1800Hz/8830kHz KENWOOD TS450, TS570, TS690,
TS850, TS950
1 pc: 4 190 Kč
RoHS
INRAD-528 KENWOOD 455kHz
500Hz CW TS140, TS680
GES08900214
1 pc: 3 090 Kč
RoHS
INRAD 500Hz/455kHz CW KENWOOD TS140, TS680
Fil ter 500Hz/-6dB, 455kHz, CW, Shape Factor 1.8. Ul timate rejection >90dB.
Ripple <2dB. Typical Inserti on Loss: <6dB. Zin=Zout=2000 Ohms.
Dimensions: 64x24x22 mm. Fi lter soldered on custom PC board. Replace the
YG455C1 (=YK455C1) Kenwood filter.
1 pc: 4 190 Kč
RoHS
INRAD-528 KENWOOD 455kHz
500Hz CW TS450S, TS690
GES08900215
INRAD 500Hz/455kHz KENWOOD TS450S, TS690
Fil ter 500Hz/-6dB, 455kHz, CW, Shape Factor 1.8. Ul timate rejection >90dB.
Ripple <2dB. Typical Insertion Loss: <6dB. Zin=Zout=2000Ohms. Dimensions:
64x24x22 mm. Drop in exact repl acement. Repl ace for YG455C1
(=YK455C1) Kenwood fil ter.
1 pc: 4 190 Kč
RoHS
Fil ter 1800Hz/-6dB, 8830kHz, SSB, Shape Factor 1.5. Ultimate rejecti on
>90dB. Ri pple <2dB. Typi cal Insertion Loss: <5dB. Di mensi ons: 50x18x18
mm. Plug-in / custom PC board; no soldering requi red. Fil ter is better than
ori ginal YK88SN1.
INRAD-94 KENWOOD 8830kHz
2100Hz SSB TS450, TS570, TS690,
TS850, TS950
GES08900226
INRAD 2100Hz/8830kHz. KENWOOD TS450, TS570, TS690,
TS850, TS950
Filter 2100Hz/-6dB, 8830kHz, SSB, Shape Factor 1.5. Ul timate rej ection
>90dB. Ri pple <2dB. Typi cal Insertion Loss: <5dB. Dimensions: 50x18x18
mm. Plug-i n / custom PC board; no soldering required. Better replace for
original YK88SN1.
1 pc: 1 690 Kč
Action
RoHS
INRAD-92 KENWOOD 10695kHz
2100Hz CW TRC80, TS50, TS60,
TS2000, TS2000X
GES08902006
INRAD-88 KENWOOD 8830kHz
2800Hz SSB TS930, TS940
GES08900233
INRAD 2800Hz/8830kHz KENWOOD TS930, TS940
INRAD 2100Hz/10695kHz. KENWOOD TRC80, TS50, TS60,
TS2000, TS2000X
Fil ter 2800Hz/-6dB, 8830kHz, SSB, Shape Factor 1.5. Inrad filter is much
larger than mfgr's fi lter. Wi re i n. Ulti mate rej ection >90dB. Ri pple <2dB.
Typi cal Insertion Loss: <5dB. Dimensions: 50x18x18 mm.
1 pc: 3 090 Kč
RoHS
INRAD-475 KENWOOD 8830kHz
4000Hz AM TS450S, TS690
GES08900234
INRAD 4000Hz/8830kHz KENWOOD TS450S, TS690
INRAD-900 KENWOOD 40,0550MHZ
ROOFING TS950SDX
GES08901850
INRAD VHF Bare Filter 40,0550MHz (>4kHz, 6 poles, 50 Ohm s) for
2nd RX TS950SDX
1 pc: 2 990 Kč
RoHS
INRAD-901 KENWOOD 44,9300MHZ
ROOFING TS930
GES08902024
INRAD VHF Bare Filter 44,9300MHz (>4kHz, 6 poles, 50 Ohm s) for
m ain RX TS930
Fil ter 1800Hz/-6dB, 8830kHz, CW and SSB, Shape Factor 1.5. Ulti mate
rej ection
>90dB.
Ripple
<2dB.
Typical
Insertion
Loss:
<5dB.
Zin=Zout=2000Ohms. Dimensions: 50x18x18 mm. Wire in filter; requires
soldering short pi gtails or mi niature coax.
1 pc: 3 090 Kč
RoHS
INRAD-89 KENWOOD 455kHz
2800Hz SSB TS140, TS680, TS930,
TS940
GES08900228
Fil ter 4000Hz/-6dB, 8830kHz, AM, Shape Factor 1.6. Ultimate rejecti on
>90dB. Ripple <2dB. Typical Insertion Loss: <5dB. Zin=Zout=2000Ohms.
Dimensions: 50x18x18 mm. Drop in exact repl acement.
1 pc: 3 090 Kč
RoHS
INRAD 2800Hz/455kHz. KENWOOD TS140, TS680, TS930, TS940
INRAD-475 KENWOOD 8830kHz
4000Hz AM TS850, TS930, TS940,
TS950
GES08900235
1 pc: 2 990 Kč
RoHS
INRAD-903 KENWOOD 45,0500MHZ
ROOFING TS940
INRAD VHF Bare Filter 45,0500MHz (>4kHz, 6 poles, 50 Ohm s) for
m ain RX TS940
INRAD 4000Hz/8830kHz KENWOOD TS850, TS930, TS940, TS950
Fil ter 4000Hz/-6dB, 8830kHz, AM, Shape Factor 1.6. Ultimate rejecti on
>90dB. Ri pple <2dB. Typi cal Insertion Loss: <5dB. Di mensi ons: 50x18x18
mm. Fil ter sol dered on custom PC board.
1 pc: 3 090 Kč
RoHS
INRAD-100 KENWOOD 8830kHz
6000Hz AM TS450S, TS690
GES08900236
1 pc: 2 990 Kč
RoHS
INRAD-915 KENWOOD 73,0500MHZ
ROOFING TS450, TS690, TS850,
TS870, TS950
GES08901849
INRAD VHF Bare Filter 73,0500MHz (>4kHz, 6 poles, 50 Ohm s)
For main RX TS450, T S690, TS850, T S870, TS950S, TS950SD, TS950SDX
INRAD 6000Hz/8830kHz KENWOOD TS450S, TS690
Fil ter 2800Hz/-6dB, 455kHz, SSB, Shape Factor 1.5. Inrad fil ter is much
larger than mfgr's filter. Wi re in. Ulti mate rejecti on >90dB. Ripple <2dB.
Typi cal Insertion Loss: <5dB. Zin=Zout=2000Ohms. Di mensi ons: 64x24x22
mm.
1 pc: 2 990 Kč
RoHS
Ten-Tec
GES08902131
INRAD-760 TEN-TEC 9000.75kHz
250Hz CW CORSAIR, DELTA, OMNI,
ORION, PARAGON, TRITON, SIENNA
1 pc: 4 190 Kč
RoHS
INRAD-89 KENWOOD 455kHz
2800Hz SSB TS450S, TS690
GES08902023
GES08900229
INRAD 250Hz/9000.75kHz TEN-TEC
INRAD 2800Hz/455kHz KENWOOD TS450S, TS690
Fil ter 2800Hz/-6dB, 455kHz, SSB, Shape Factor 1.5. Ulti mate rejecti on
>90dB. Ripple <2dB. Typical Inserti on Loss: <5dB. Di mensi ons: 64x24x22
mm. Drop i n exact replacement.
1 pc: 4 190 Kč
RoHS
INRAD-89 KENWOOD 455kHz
2800Hz SSB TS850, TS950
GES08900230
Crystal filter 8-pol e. 6000Hz/-6dB, 8830kHz, AM, Shape Factor 1.6. Ulti mate
rej ection
>90dB.
Ripple
<2dB.
Typical
Insertion
Loss:
<5dB.
Zin=Zout=2000Ohms. Dimensions: 50x18x18 mm. Drop in exact
replacement.
1 pc: 3 090 Kč
RoHS
INRAD 2800Hz/455kHz KENWOOD TS850, TS950
Fil ter 2800Hz/-6dB, 455kHz, SSB, Shape Factor 1.5. Ulti mate rejecti on
>90dB. Ripple <2dB. Typical Inserti on Loss: <5dB. Di mensi ons: 64x24x22
mm. Fil ter sol dered on custom PC board.
1 pc: 4 190 Kč
RoHS
INRAD-88 KENWOOD 8830kHz
2800Hz SSB TS450S, TS690
GES08900231
INRAD-100 KENWOOD 8830kHz
6000Hz AM TS850, TS950
GES08900237
INRAD 6000Hz/8830kHz KENWOOD TS850, TS950
Crystal filter 8-pol e. 6000Hz/-6dB, 8830kHz, AM, Shape Factor 1.6. Ulti mate
rej ection >90dB. Rippl e <2dB. Typical Insertion Loss: <5dB. Dimensions:
50x18x18 mm. Filter soldered on custom PC board.
1 pc: 3 090 Kč
INRAD 2800Hz/8830kHz KENWOOD TS450S, TS690
RoHS
INRAD-100 KENWOOD 8830kHz
6000Hz AM TS930, TS940
GES08900238
Filter 250Hz/-6dB, 9000.75kHz, CW. Typi cal Insertion Loss: 250Hz <9dB.
8-pole crystal fi lter. Superior sel ectivity. Shape factor 2.2. Filter is soldered on
custom PCB. Plug in fi lter, exact replace OEM fi lter. For TEN-TEC Corsai r I,II,
Delta I, Omni B,C,V,VI,VI+, Orion, Paragon, Tri ton IV, Si enna. Repl ace
T EN-T EC 219.
1 pc: 2 990 Kč
RoHS
INRAD 6000Hz/8830kHz KENWOOD TS930, TS940
Crystal filter 8-pol e. 6000Hz/-6dB, 8830kHz, AM, Shape Factor 1.6. Drop in
but filter sl ightly larger in size than original. Ul timate rejection >90dB. Ripple
<2dB. Typical Inserti on Loss: <5dB. Dimensions: 50x18x18 mm.
1 pc: 3 090 Kč
INRAD-353 TEN-TEC ORION II
9001.5kHz 250Hz ROOFING FILTER
GES08902045
INRAD 250Hz/9001.5kHz TEN-TEC ORION II Roofing Filter
RoHS
INRAD-260 KENWOOD 8831,5kHz
6000Hz AM TS430
GES08901789
INRAD 6000Hz/8831.5kHz KENWOOD TS430 (better replace for
YK88A from KENWOOD)
Fil ter 2800Hz/-6dB, 8830kHz, SSB, Shape Factor 1.5. Ultimate rejecti on
>90dB. Ripple <2dB. Typical Insertion Loss: <5dB. Zin=Zout=2000Ohms.
Dimensions: 50x18x18 mm. Drop in exact repl acement.
1 pc: 3 090 Kč
RoHS
INRAD-88 KENWOOD 8830kHz
2800Hz SSB TS570
GES08901632
Fil ter 6000Hz/-6dB, 8831.5kHz, AM, Shape Factor 1.6. Drop in but fil ter
slightl y l arger in size than original. Ulti mate rej ection >90dB. Ri pple <2dB.
Typi cal Insertion Loss: <5dB. Dimensions: 50x18x18 mm.
1 pc: 3 090 Kč
INRAD-TS930 KENWOOD
44.930MHZ ROOFING FILTER
INRAD Roofing Filter Module 44,9300MHz for main RX TS930
Kenwood
INRAD 2800Hz/8830kHz KENWOOD TS570
Fil ter 2800Hz/-6dB, 8830kHz, SSB, Shape Factor 1.5. Ultimate rejecti on
>90dB. Ripple <2dB. Typical Inserti on Loss: <5dB. Di mensi ons: 50x18x18
mm. Fil ter sol dered on custom PC board.
1 pc: 3 090 Kč
RoHS
INRAD-88 KENWOOD 8830kHz
2800Hz SSB TS850, TS950
GES08900232
1 pc: 4 290 Kč
RoHS
INRAD-TS950S, TS950SD,
TS950SDX KENWOOD 73,0500MHZ
ROOFING FILTER
1 pc: 3 090 Kč
GES08902085
INRAD Roofing Filter Module 73,0500MHz for main RX
TS950S,TS950SD,TS950SDX Kenwood
INRAD 2800Hz/8830kHz KENWOOD TS850, TS950
RoHS
GES08902086
1 pc: 4 890 Kč
RoHS
Filter 250Hz/-6dB, 9001.5kHz, CW. Four-pol e crystal i nput roofing filter. Shape
factor 5.2. Fi lter is soldered on custom PCB. Plug in fi lter.
1 pc: 1 890 Kč
RoHS
GES08902130
INRAD-759 TEN-TEC 9000.75kHz
400Hz CW CORSAIR, DELTA, OMNI,
ORION, PARAGON, TRITON, SIENNA
INRAD-359 TEN-TEC ORION II
9001.5kHz 2400Hz ROOFING
FILTER
INRAD 400Hz/9000.75kHz TEN-TEC
INRAD 2400Hz/9001.5kHz TEN-TEC ORION II Roofing Filter
GES08902048
Yaesu
INRAD-719 YAESU 455kHz 125Hz
CW FT847
GES08900239
INRAD 125Hz/455kHz YAESU FT847
Fil ter 400Hz/-6dB, 9000.75kHz, CW. Typical Insertion Loss: <8dB. 8-pole
crystal filter. Superior selectivity. Shape factor 2.1. Fil ter is soldered on custom
PCB. Plug in filter, exact repl ace OEM fil ter. For TEN-TEC Corsair I,II, Del ta I,
Omni B,C,V,VI,VI+, Ori on, Paragon, T riton IV, Sienna. Repl ace TEN-TEC
217.
1 pc: 2 990 Kč
RoHS
INRAD-354 TEN-TEC ORION II
9001.5kHz 500Hz ROOFING FILTER
GES08902046
INRAD 500Hz/9001.5kHz TEN-TEC ORION II Roofing Filter
Fil ter 2400Hz/-6dB, 9001.5kHz, SSB. Four-pole crystal i nput roofi ng filter.
Shape factor 4.8. Fil ter is soldered on custom PCB. Pl ug in fil ter.
1 pc: 1 890 Kč
RoHS
INRAD-756 TEN-TEC 9001.5kHz
2400Hz ORION, OMNI, PARAGON,
CORSAIR, DELTA ROOFING FILTER
GES08901984
Filter 125Hz/-6dB, 455kHz, CW. Crystal fil ter. Shape factor 2.2. Mounted on
custom PC board, drop in. (For FT847 only: This filter has much larger
dimensions and will not fi t in the socket. Must be wired in with mi niature
coax. In the FT 847 T CVR is room for one or two crystal filter plus one
mechanical fil ter).
1 pc: 2 890 Kč
INRAD 2400Hz/9001.5kHz TEN-TEC ORION, OMNI V,VI,VI+,
PARAGON, CORSAIR I,II, DELTA I
Action
RoHS
INRAD-719 YAESU 455kHz 125Hz
CW FT890, FT900, FT990
GES08901929
INRAD 125Hz/455kHz YAESU FT890, FT900, FT990
Filter 125Hz/-6dB, 455kHz, CW. Shape Factor 2.2. Ultimate rejecti on >80dB.
Ripple <2dB. Typical insertion loss <9dB. Zin/Zout 500 Ohms. Sol der in filter;
replace OEM fi lter and sol der connections.
1 pc: 4 190 Kč
RoHS
INRAD-719C YAESU 455kHz 125Hz
CW FT1000, FT1000MP, MARKV,
FRG100B
GES08900240
INRAD 125Hz/455kHz YAESU FT1000, FT1000MP, MARKV,
FRG100B
Filter 125Hz/-6dB, 455kHz, CW. Shape Factor 2.2. Ultimate rejecti on >80dB.
Ripple <2dB. Typical i nsertion loss <9dB. Zin/Zout 500 Ohms. For Mai n or
Sub-receiver; Filter i s sol dered on custom PC board. Plug in.
Fil ter 500Hz/-6dB, 9001.5kHz, CW. Four-pole crystal input roofi ng fil ter. Shape
factor 5.1. Filter i s sol dered on custom PCB. Plug i n filter.
1 pc: 1 890 Kč
RoHS
INRAD-757 TEN-TEC 6298.5kHz
2400Hz OMNI, ARGOSY, PARAGON
ROOFING FILTER
GES08901985
1 pc: 4 190 Kč
Fil ter 2400Hz/-6dB, 9001.5kHz, SSB. Ten-pole crystal fil ter. Superior
selectivity. Shape factor 1.4. Fil ter is soldered on custom PCB. Plug in filter,
exact replace OEM filter.
1 pc: 3 490 Kč
RoHS
INRAD 2400Hz/6298.5kHz TEN-TEC OMNI V,VI,VI+,B,C, ARGOSY
I,II, PARAGON
INRAD-357 TEN-TEC ORION II
9001.5kHz 2800Hz ROOFING
FILTER
RoHS
INRAD-704 YAESU 455kHz 250Hz
CW FT847
GES08900241
INRAD 250Hz/455kHz YAESU FT847
GES08902047
INRAD 2800Hz/9001.5kHz TEN-TEC ORION II Roofing Filter
Filter 250Hz/-6dB, 455kHz, CW. Crystal fil ter. Shape factor 1.8. Mounted on
custom PC board, drop in. (For FT847 only: This filter has much larger
dimensions and will not fi t in the socket. Must be wired in with mi niature
coax. In the FT 847 T CVR is room for one or two crystal filter plus one
mechanical fil ter). Better replace for original YF110CN - XF110CN.
1 pc: 4 190 Kč
Fil ter 2400Hz/-6dB, 6298.5kHz, SSB. Ten-pole crystal fi lter. Superior
selectivity. Shape factor 1.4. Fil ter i s soldered on custom PCB. Plug in filter,
exact replace OEM filter.
1 pc: 3 490 Kč
RoHS
INRAD-757 TEN-TEC 6298.5kHz
2400Hz ARGONAUT ROOFING
FILTER
GES08901986
INRAD 2400Hz/6298.5kHz TEN-TEC ARGONAUT, 506, 509, 515
Fil ter 2400Hz/-6dB, 6298.5kHz, SSB. Ten-pole crystal fi lter. Superior
selectivity. Shape factor 1.4. Fi lter is soldered on custom PCB. Wire in filter,
reversible modi fication for the radio.
1 pc: 3 490 Kč
RoHS
RoHS
Fil ter 2800Hz/-6dB, 9001.5kHz, SSB. Four-pole crystal i nput roofi ng filter.
Shape factor 4.6. Fil ter is soldered on custom PCB. Pl ug in fil ter.
1 pc: 1 890 Kč
RoHS
INRAD-902 TEN-TEC 45,0000MHz
ORION ROOFING FILTER
GES08902076
GES08901925
INRAD 250Hz/455kHz YAESU FT890, FT900, FT990
Filter 250Hz/-6dB, 455kHz, CW. Ulti mate rejection >80dB. Ripple <2dB.
Typical insertion loss <9dB. Zin/Zout 500 Ohms. Solder in filter; repl ace OEM
filter and solder connections. Better repl ace for origi nal YF110CN - XF110CN.
1 pc: 4 190 Kč
INRAD VHF Bare Filter 45,0000MHz (>4kHz, 6 poles, 50 Ohms), for
2nd RX ORION, ORION II. Filter only
1 pc: 2 990 Kč
RoHS
INRAD-704 YAESU 455kHz 250Hz
CW FT890, FT900, FT990
RoHS
INRAD-704C YAESU 455kHz 250Hz
CW FT1000, FT1000MP, MARKV,
FRG100B
GES08900242
INRAD 250Hz/455kHz YAESU FT1000, FT1000MP, MARKV,
FRG100B
Filter 250Hz/-6dB, 455kHz, CW. Shape Factor 1.8. Ultimate rejecti on >80dB.
Ripple <2dB. Typical i nsertion loss <9dB. Zin/Zout 500 Ohms. For Mai n or
Sub-receiver; Filter is soldered on custom PC board. Plug i n. Better repl ace
for ori ginal YF110CN - XF110CN.
1 pc: 4 190 Kč
RoHS
INRAD-21 YAESU 455,7kHz 250Hz
CW FT1000 SUB RX
GES08900243
INRAD 250Hz/455,7kHz YAESU FT1000 Sub Receiver
Filter 250Hz/-6dB, 455,7kHz, CW. Shape Factor 1.9. For Sub-receiver
FT1000. Wi re in at place.
1 pc: 4 190 Kč
INRAD-708A YAESU 8215kHz 250Hz
CW FT920
GES08901952
INRAD 250Hz/8215kHz YAESU
INRAD-703 YAESU 455kHz 400Hz
CW FT890, FT900, FT990
GES08901953
INRAD 400Hz/455kHz YAESU FT890, FT900, FT990
INRAD-721 YAESU 455kHz 500Hz
CW FT847
GES08900255
INRAD 500Hz/455kHz YAESU FT847
Fil ter 400Hz/-6dB, 455kHz, CW. Shape Factor 1.7. Ultimate rejection >80dB.
Ripple <2dB. Typi cal insertion loss <9dB. Zin/Zout 500 Ohms. Sol der in filter;
replace OEM filter and solder connections.
1 pc: 4 190 Kč
RoHS
INRAD-703C YAESU 455kHz 400Hz
FT1000, FT1000MP, MARKV,
FRG100B
GES08900251
INRAD 400Hz/455kHz YAESU FT1000, FT1000MP, MARKV,
FRG100B
Fil ter 400Hz/-6dB, 455kHz, CW. Shape Factor 1.7. Ultimate rejection >80dB.
Ripple <2dB. Typi cal i nsertion loss <9dB. Zin/Zout 500 Ohms. For Main or
Sub-receiver; Filter is soldered on custom PC board. Pl ug in.
Fil ter 250Hz/-6dB, 8215kHz, CW, shape factor 1.9. Filter is soldered on little
board cal led SSB ADAPT ER BOARD. You can instal one filter, repl acing the
OEM filter. You can instal l in FT-920 more fi lters only when the INRAD-920
SWITCHBOARD MOD ( GES08901740 ) wil l be used.
1 pc: 3 490 Kč
RoHS
INRAD-708B YASEU 8215kHz 250Hz
CW FT1000, FT1000MP, MARKV
1 pc: 4 190 Kč
RoHS
INRAD-99 YAESU 455.7kHz 400Hz
CW FT1000 SUB RX
GES08900252
INRAD 400Hz/455,7kHz YAESU FT1000 Sub Receiver
Fil ter 400Hz/-6dB, 455,7kHz, CW; For Sub-receiver FT 1000; Wire in at place.
GES08900244
INRAD 250Hz/8215kHz YAESU FT1000, FT1000MP, MARKV
Fil ter 250Hz/-6dB, 8215kHz, CW, shape factor 2.1. Fil ter is soldered on custom
PC board. Pl ug in. Better replace for original XF114CN - YF114CN.
1 pc: 4 190 Kč
INRAD-701A YAESU 8215kHz 400Hz
CW FT920
GES08900254
1 pc: 4 190 Kč
RoHS
INRAD-721 YAESU 455kHz 500Hz
CW FT890, FT900, FT990
GES08901954
INRAD 500Hz/455kHz YAESU FT890, FT900, FT990
Filter 500Hz/-6dB, 455kHz, CW. Shape Factor 1.7. Ultimate rejecti on >80dB.
Ripple <2dB. Typical insertion loss <9dB. Zin/Zout 500 Ohms. Sol der in filter;
replace OEM fi lter and sol der connections.
INRAD 400Hz/8215kHz YAESU FT920
1 pc: 3 490 Kč
RoHS
INRAD-119A YAESU 8215,9kHz
250Hz CW FT600, FT840
Filter 500Hz/-6dB, 455kHz, CW. Crystal fil ter. Shape factor 1.7. Mounted on
custom PC board, drop in. (For FT847 only: This filter has much larger
dimensions and will not fi t in the socket. Must be wired in with mi niature
coax. In the FT 847 T CVR is room for one or two crystal filter plus one
mechanical fil ter).
1 pc: 2 890 Kč
GES08900245
Action
RoHS
INRAD-721C YAESU 455kHz 500Hz
CW FT1000, FT1000MP, MARKV,
FRG100B
INRAD 250Hz/8215,9kHz YAESU FT600, FT840
GES08900259
INRAD 500Hz/455kHz YAESU FT1000, FT1000MP, MARKV,
FRG100B
Filter 500Hz/-6dB, 455kHz, CW. Shape Factor 1.7. Ultimate rejecti on >80dB.
Ripple <2dB. Typical i nsertion loss <9dB. Zin/Zout 500 Ohms. For Mai n or
Sub-receiver; Filter i s sol dered on custom PC board. Plug in.
1 pc: 2 890 Kč
Action
RoHS
Crystal fi lter 8-pole. 250Hz/-6dB, 8215,9kHz, CW.
1 pc: 3 090 Kč
RoHS
INRAD-712C YAESU 455kHz 300Hz
CW FT847, FT1000, FT1000MP,
MARKV, FRG100B
GES08900246
Fil ter 400Hz/-6dB, 8215kHz, CW, shape factor 2.1. Filter i s soldered on little
board cal led SSB ADAPTER BOARD. You can instal one filter, replacing the
OEM filter. You can instal l in FT-920 more fi lters only when the INRAD-920
SWITCHBOARD MOD ( GES08901740 ) wil l be used.
1 pc: 3 090 Kč
RoHS
INRAD 300Hz/455kHz YAESU FT847, FT1000, FT1000MP, MARKV,
FRG100B
INRAD-701B YAESU 8215kHz 400Hz
CW FT1000, FT1000MP, MARKV
INRAD-120A YAESU 8215,9kHz
500Hz CW FT600, FT840
INRAD 500Hz/8215.9kHz YAESU FT600, FT840
Crystal filter 8-pol e. 500Hz/-6dB, 8215,9kHz, CW. Filter mounted on custom
PC.
1 pc: 3 090 Kč
GES08900253
INRAD 400Hz/8215kHz YAESU FT1000, FT1000MP, MARKV
Fil ter 400Hz/-6dB, 8215kHz, CW, shape factor 2.1. Fil ter is soldered on custom
PC board. Pl ug in.
GES08900260
INRAD-672 YAESU 10940kHz 500Hz
CW FT990
GES08901956
INRAD 500Hz/10940kHz YAESU FT990
1 pc: 3 090 Kč
RoHS
INRAD-705F YAESU 455kHz 500Hz
CW FT817, FT857, FT897, FT2000
GES08900257
INRAD 500Hz/455kHz YAESU FT817, FT857, FT897, FT2000
Fil ter 300Hz/-6dB, 455kHz, CW. Shape Factor 2.2. Colli ns 7-pol e mechanical
filter mounted on custom PC, pl ug i n board. For Main and Sub-recei ver of
FT1000, FT 1000MP and MARK-V.
1 pc: 3 490 Kč
RoHS
INRAD-712F YAESU 455kHz 300Hz
CW FT817, FT857, FT897, FT2000
GES08900249
Filter 500Hz/-6dB, 10940kHz, CW. Shape factor 2.2. Ultimate rej ection
>80dB. Ri pple <2dB. Typical inserti on loss <7dB. Zin/Zout 500 Ohms.
INRAD 300Hz/455kHz YAESU FT817, FT857, FT897, FT2000
Fil ter 300Hz/-6dB, 455kHz, CW; Shape Factor 2.5. Colli ns 7-pole mechanical
filter mounted on custom PC, plug i n board. Better repl ace for Yaesu fil ter
YF122CN (YF-122CN).
1 pc: 3 490 Kč
RoHS
INRAD-703 YAESU 455kHz 400Hz
CW FT847
GES08900250
INRAD 400Hz/455kHz YAESU FT847
1 pc: 3 090 Kč
Fil ter 500Hz/-6dB, 455kHz, CW; Shape Factor 2.5. Collins 7-pole mechanical
filter mounted on custom PC, plug in board. New model to INRAD-705E.
Better than origi nal YF-122C (YF122C).
1 pc: 2 990 Kč
RoHS
INRAD-713 YAESU 455kHz 1000Hz
CW FT847
GES08900261
INRAD 1000Hz/455kHz YAESU FT847
RoHS
INRAD-705C YAESU 455kHz 500Hz
CW FT1000, FT1000MP, MARKV
GES08900256
INRAD 500Hz/455kHz YAESU FT847, FT1000, FT1000MP, MARKV
Fil ter 500Hz/-6dB, 455kHz, CW. Shape Factor 2.5. Colli ns 7-pole mechanical
filter mounted on custom PC, plug i n board. For Main and Sub-receiver of
FT1000, FT 1000MP and MARK-V. Better replace original YF115C - XF115C.
1 pc: 2 990 Kč
RoHS
Fil ter 400Hz/-6dB, 455kHz, CW. Crystal fi lter. Shape factor 1.7. Mounted on
custom PC board, drop in. (For FT847 onl y: This filter has much l arger
dimensions and wil l not fit in the socket. Must be wi red in with mini ature
coax. In the FT847 TCVR is room for one or two crystal filter plus one
mechanical fi lter).
1 pc: 4 190 Kč
RoHS
Filter 1000Hz/-6dB, 455kHz, CW. Crystal fil ter 8-pole. Shape factor 1.7.
Mounted on custom PC board, drop i n. (For FT847 only: This fi lter has much
l arger di mensi ons and will not fit i n the socket. Must be wi red in wi th
miniature coax. In the FT 847 TCVR is room for one or two crystal filter plus
one mechanical filter).
1 pc: 4 190 Kč
RoHS
INRAD-729 YAESU 455kHz 1000Hz
CW FT817, FT857, FT897, FT2000
GES08902152
INRAD 1000Hz/455kHz YAESU FT817, FT857, FT897, FT2000
Filter 1000Hz/-6dB, 8-pole Coll ins, 455kHz, CW. Shape Factor 2.5. Ultimate
rejection >80dB. Ripple <2dB. Typical i nsertion l oss <6dB. Zin/Zout 2000
Ohms // 30pF. For Mai n or Sub-receiver; Filter is soldered on custom PC
board. Pl ug in.
1 pc: 3 490 Kč
INRAD-713 YAESU 455kHz 1000Hz
CW FT890, FT900, FT990
GES08901955
INRAD 1000Hz/455kHz YAESU FT890, FT900, FT990
Crystal filter 8-pol e. 1000Hz/-6dB, 455kHz, CW. Shape Factor 1.7. Ulti mate
rej ection >80dB. Rippl e <2dB. Typical insertion loss <9dB. Zin/Zout 500
Ohms. Solder in fil ter; repl ace OEM fil ter and solder connections.
INRAD-711.1 YAESU 8215kHz
1800Hz SSB FT920
GES08901948
INRAD 1800Hz/8215kHz YAESU FT920. Replace directly OEM
2.4kHz filter
INRAD-702 YAESU 455kHz 2100Hz
SSB FT847
GES08900271
INRAD 2100Hz/455kHz YAESU FT847
1 pc: 4 190 Kč
RoHS
INRAD-713C YAESU 455kHz 1000Hz
CW FT1000, FT1000MP, MARKV,
FRG100B
GES08900262
INRAD 1000Hz/455kHz YAESU FT1000, FT1000MP, MARKV,
FRG100B
Crystal filter 8-pol e. 1000Hz/-6dB, 455kHz, CW. Shape Factor 1.7. Ulti mate
rej ection >80dB. Rippl e <2dB. Typical insertion loss <9dB. Zin/Zout 500
Ohms. For Main or Sub-receiver; Filter i s sol dered on custom PC board. Pl ug
in.
1 pc: 4 190 Kč
RoHS
INRAD-729 YAESU 455kHz 1000Hz
CW FT847
GES08902153
Fil ter 1800Hz/-6dB, 8215kHz, SSB, shape factor 1.5. Fil ter is soldered on little
board cal led SSB ADAPTER BOARD. You can instal one filter, replacing the
OEM 2.4kHz fil ter. You can instal l i n FT-920 more filters only when the
INRAD-920 SWITCHBOARD MOD ( GES08901740 ) wi ll be used.
INRAD 1000Hz/455kHz YAESU FT847
1 pc: 3 490 Kč
Fil ter 1000Hz/-6dB, 8-pole Col lins, 455kHz, CW. Shape Factor 2.5. Ulti mate
rej ection >80dB. Rippl e <2dB. Typical inserti on loss <6dB. Zin/Zout 2000
Ohms // 30pF. Fil ter is soldered on custom PC board.
1 pc: 2 790 Kč
INRAD-718A YAESU 8215kHz
1000Hz CW FT920
GES08901951
RoHS
INRAD-711B YAESU 8215kHz
1800Hz SSB FT1000, FT1000MP,
MARKV
GES08900266
1 pc: 4 190 Kč
RoHS
INRAD-702 YAESU 455kHz 2100Hz
SSB FT890, FT900, FT990
GES08901853
INRAD 2100Hz/455kHz YAESU FT890, FT900, FT990
INRAD 1800Hz/8215kHz YAESU FT1000, FT1000MP, MARKV
Fil ter 1800Hz/-6dB, 8215kHz, SSB, shape factor 1.5. Fil ter is soldered on
custom PC board. Pl ug in.
INRAD 1000Hz/8215kHz YAESU FT920
Filter 2100Hz/-6dB, 455kHz, SSB; Crystal fi lter. Ul timate rej ection >80dB.
Ripple <2dB. Typi cal insertion loos <6dB. Zin/Zout 500 Ohms. Shape factor
1.5. Much larger dimensions, wil l not fit in the socket. Wire in fi lter; solder
short pigtai ls or mini ature coax. In the TCVR i s room for one or two crystal
filter plus one mechanical fi lter.
1 pc: 3 490 Kč
RoHS
INRAD-720D YAESU 455kHz 2000Hz
SSB FT847
GES08900267
Filter 2100Hz/-6dB, 455kHz, SSB. Crystal fi lter. Shape factor 1.5. Ultimate
rejection >80dB. Ripple <2dB. Typical insertion l oss <6dB. Zin/Zout 500
Ohms. Solder in filter; replace OEM filter and solder connecti ons.
1 pc: 4 190 Kč
RoHS
INRAD-702C YAESU 455kHz 2100Hz
SSB FT1000, FT1000MP, MARKV
GES08901854
INRAD 2100Hz/455kHz YAESU FT1000, FT1000MP, MARKV
INRAD 2000Hz/455kHz YAESU FT847
Filter 2100Hz/-6dB, 455kHz, SSB. Crystal fi lter. Shape factor 1.5. Ultimate
rejection >80dB. Ripple <2dB. Typical insertion l oss <6dB. Zin/Zout 500
Ohms. For Mai n and Sub receiver. Filter is soldered on custom PCB. Plug i n;
replace OEM fi lter.
1 pc: 4 190 Kč
RoHS
INRAD-709.1 YAESU 8215kHz
2100Hz SSB FT920
GES08901739
INRAD 2100Hz/8215kHz YAESU FT920. Replace directly OEM
2.4kHz filter
Fil ter 1000Hz/-6dB, 8215kHz, CW, shape factor 1.5. Filter is soldered on little
board cal led SSB ADAPT ER BOARD. You can instal one filter, repl acing the
OEM filter. You can instal l in FT-920 more fi lters only when the INRAD-920
SWITCHBOARD MOD ( GES08901740 ) wil l be used.
1 pc: 3 090 Kč
RoHS
INRAD-718B YAESU 8215kHz
1000Hz CW FT1000, FT1000MP,
MARKV
GES08900263
Fil ter 2000Hz/-6dB, 455kHz, CW. Zin/Zout=200Ohm//30pF. Coll ins 8-pole
mechanical fi lter mounted on custom PC, plug in board.
1 pc: 2 990 Kč
RoHS
INRAD 1000Hz/8215kHz YAESU FT1000, FT1000MP, MARKV
Fil ter 1000Hz/-6dB, 8215kHz, CW, shape factor 1.6. Fi lter i s soldered on
custom PC board. Pl ug in.
1 pc: 3 090 Kč
RoHS
INRAD-714 YAESU 455kHz 1800Hz
SSB FT847
INRAD-720F YAESU 455kHz 2000Hz
SSB FT817, FT857, FT897, FT2000
GES08900270
INRAD 2000Hz/455kHz YAESU FT817, FT857, FT897, FT2000
Fil ter 2000Hz/-6dB, 455kHz, SSB; Shape Factor 1.9. Collins 8-pole
mechanical fi lter mounted on custom PC, plug in board.
GES08900264
1 pc: 2 990 Kč
RoHS
INRAD-720C YAESU 455kHz 2000Hz
SSB FT1000, FT1000MP, MARKV
INRAD 1800Hz/455kHz YAESU FT847
GES08900268
1 pc: 1 890 Kč
INRAD 2000Hz/455kHz YAESU FT1000, FT1000MP, MARKV
Fil ter 2000Hz/-6dB, 455kHz, SSB; Zin/Zout=200Ohm//30pF. For Main or
Sub-receiver; Col lins 8-pole Mechanical Fi lter. Better replace for ori ginal
XF110SN - YF110SN.
1 pc: 2 890 Kč
Action
RoHS
INRAD-709B YAESU 8215kHz
2100Hz SSB FT1000, FT1000MP,
MARKV
GES08900273
INRAD 2100Hz/8215kHz YAESU FT1000, FT1000MP, MARKV
Action
RoHS
INRAD-422 YAESU 10940kHz
2000Hz SSB FT990
Filter 2100Hz/-6dB, 8215kHz, SSB, shape factor 1.5. Filter is soldered on little
board call ed SSB ADAPTER BOARD. You can i nstal one filter, replacing the
OEM 2.4kHz filter. You can install in FT-920 more fi lters onl y when the
INRAD-920 SWITCHBOARD MOD ( GES08901740 ) wil l be used.
GES08901924
Filter 2100Hz/-6dB, 8215kHz, SSB, shape factor 1.5. Filter is soldered on
custom PC board. Plug in. Better approximate equi valent to original
XF114SN, YF114SN.
INRAD 2000Hz/10940kHz YAESU FT990
1 pc: 1 990 Kč
Action
RoHS
INRAD-717F YAESU 455kHz 2300Hz
SSB FT817, FT857, FT897
Fil ter 1800Hz/-6dB, 455kHz, SSB; Crystal filter. Ultimate rejecti on >80dB.
Ripple <2dB. Typical i nsertion l oos <6dB. Zin/Zout 500 Ohms. Shape factor
1.5. Much l arger di mensi ons, wi ll not fit in the socket. Wire i n filter; solder
short pigtails or miniature coax. In the TCVR is room for one or two crystal
filter plus one mechani cal filter.
GES08900275
INRAD 2300Hz/455kHz YAESU FT817, FT857, FT897
1 pc: 4 190 Kč
RoHS
INRAD-714 YAESU 455kHz 1800Hz
SSB FT890, FT900, FT990
GES08901943
INRAD 1800Hz/455kHz YAESU FT890, FT900, FT990
Fil ter 1800Hz/-6dB, 455kHz, SSB. Crystal filter. Shape factor 1.5. Ulti mate
rej ection >80dB. Rippl e <2dB. Typical insertion loss <6dB. Zin/Zout 500
Ohms. Solder in fil ter; repl ace OEM fil ter and solder connections.
1 pc: 2 890 Kč
Action
RoHS
INRAD-714C YAESU 455kHz 1800Hz
SSB FT1000, FT1000MP, MARKV
INRAD 1800Hz/455kHz YAESU FT1000, FT1000MP, MARKV
Fil ter 1800Hz/-6dB, 455kHz, SSB. Crystal filter. Shape factor 1.5. Ulti mate
rej ection >80dB. Rippl e <2dB. Typical insertion loss <6dB. Zin/Zout 500
Ohms. For Main and Sub receiver. Filter i s soldered on custom PCB. Pl ug in;
replace OEM filter.
1 pc: 2 890 Kč
Action
RoHS
Fil ter 2000Hz/-6dB, 10940kHz, SSB. Shape factor 1.6. Ulti mate rejecti on
>80dB. Ripple <2dB. Typical insertion loss <6dB. Zin/Zout 500 Ohms.
GES08900265
1 pc: 3 090 Kč
RoHS
Filter 2300Hz/-6dB, 455kHz, SSB; Shape Factor 1.6. Zi n/Zout=200Ohm
//30pF. Col lins mechani cal 10-pole filter mounted on custom PC, plug in
board. This filter i s much good replace for ori ginal XF122S - YF122S.
1 pc: 2 990 Kč
RoHS
INRAD-706D YAESU 455kHz 2500Hz
SSB FT847
GES08900276
INRAD 2500Hz/455kHz YAESU FT847
INRAD-716B YAESU 8215kHz
2800Hz SSB FT1000, FT1000MP,
MARKV
GES08900282
INRAD 2800Hz/8215kHz YAESU FT1000, FT1000MP, MARKV
Fil ter 2800Hz/-6dB, 8215kHz, SSB, shape factor 1.6. Fil ter is soldered on
custom PC board. Pl ug in.
1 pc: 3 090 Kč
RoHS
INRAD-726F YAESU 455kHz 2900Hz
SSB FT817, FT857, FT897
GES08902155
INRAD 2900Hz/455kHz YAESU FT817, FT857, FT897
Fil ter 2900Hz/-6dB, 8-pole Colli ns, 455kHz, SSB. Ultimate rejecti on >80dB.
Ripple <2dB. Typical insertion loss <6dB. Zi n/Zout 2000 Ohms // 30pF. Fil ter
is soldered on custom PC board. Pl ug in.
1 pc: 3 490 Kč
Fil ter 2500Hz/-6dB, 455kHz, CW. Shape Factor 2.0.
mechanical fi lter mounted on custom PC, plug in board.
Colli ns 8-pole
1 pc: 2 990 Kč
INRAD-724 YAESU 455kHz 3800Hz
AM FRG100
GES08902164
Fil ter 2500Hz/-6dB, 455kHz, SSB. Shape Factor 2.0. For Main or
Sub-receiver. Col lins 8-pole Mechani cal Filter. Good li ke better repl ace for
ori ginal XF115S (YF115S).
1 pc: 2 890 Kč
Action
RoHS
INRAD-715 YAESU 455kHz 2800Hz
SSB FT847
GES08900280
INRAD-910 YAESU 68,9850MHZ
ROOFING FILTER FT920
GES08902079
INRAD VHF Bare Filter 68,9850MHz (>4kHz, 6 poles, 50 Ohm s) for
m ain RX FT920
GES08902087
1 pc: 2 990 Kč
RoHS
Fil ter 3800Hz/-6dB, 455kHz, AM. Impedance Zi n = Zout = 2000 Ohm // 30pF.
Typi cal Insertion Loss < 6dB. Col lins 7 pol e Mechanical filter. For Yaesu
FRG100.
1 pc: 3 490 Kč
RoHS
INRAD-707C YAESU 455kHz 5800Hz
AM FT1000, FT1000MP, MARKV
GES08902078
INRAD VHF Bare Filter 70,4550MHz (>4kHz, 6 poles, 50 Ohm s) for
m ain RX FT1000MP
1 pc: 2 990 Kč
RoHS
INRAD 5800Hz/455kHz YAESU FT1000, FT1000MP, MARKV
Fil ter 5800Hz/-6dB, 455kHz, AM. Shape Factor 1.7. For Main or Sub-recei ver.
Col lins 8-pole Mechanical Filter.
INRAD-710A YAESU 8215kHz
6000Hz AM FT920
INRAD-914 YAESU 70,4550MHZ
ROOFING FILTER FT1000MP
GES08901949
1 pc: 2 990 Kč
INRAD 2800Hz/455kHz YAESU FT847
1 pc: 2 990 Kč
RoHS
INRAD VHF Bare Filter 69,4500MHz (>4kHz, 6poles, 50 Ohms )
m ain RX FT2000
1 pc: 2 990 Kč
INRAD 2500Hz/455kHz YAESU FT1000, FT1000MP, MARKV
INRAD VHF Bare Filter 48,6400MHz (>4kHz, 6 poles, 50 Ohm s) for
2nd RX FT1000D
1 pc: 2 990 Kč
Fil ter 2500Hz/-6dB, 455kHz, SSB; Shape Factor 2.0. Collins 8-pole
mechanical fi lter mounted on custom PC, plug in board.
GES08900277
GES08902074
RoHS
INRAD 2500Hz/455kHz YAESU FT817, FT857, FT897
INRAD-706C YAESU 455kHz 2500Hz
SSB FT1000, FT1000MP, MARKV
1 pc: 2 990 Kč
RoHS
INRAD-908 YAESU 48,6400MHZ
ROOFING FILTER FT1000D
INRAD-912 YAESU 69,4500MHZ
ROOFING FILTER FT2000
GES08900279
RoHS
GES08902075
INRAD VHF Bare Filter 47,2100MHz (>4kHz, 6 poles 50 Ohms ) for
2nd RX FT1000MP, FT1000MP MARK-V
INRAD 3800Hz/455kHz AM 7-pole Collins filter
RoHS
INRAD-706F YASEU 455kHz 2500Hz
SSB FT817, FT857, FT897
INRAD-907 YAESU 47,2100MHZ
ROOFING FILTER FT1000MP,
MARKV
INRAD IF Noise Reduction Module
FT1000MP, MARKV
GES08900287
INRAD Receiver Sensitivity/Noise Reduction IF Modul FT1000
MP,MARKV FT1000MP
GES08901950
INRAD 6000Hz/8215kHz YAESU FT920
Fil ter 2800Hz/-6dB, 455kHz, SSB; Crystal filter. Ultimate rejecti on >80dB.
Ripple <2dB. Typical i nsertion l oos <6dB. Zin/Zout 500 Ohms. Shape factor
1.5. Much l arger di mensi ons, wi ll not fit in the socket. Wire i n filter; solder
short pigtails or miniature coax. In the TCVR is room for one or two crystal
filter plus one mechani cal filter.
1 pc: 4 190 Kč
RoHS
INRAD-715 YAESU 455kHz 2800Hz
SSB FT890, FT900, FT990
IF Modul for FT-1000MP, FT-1000MP MARK-V, FT-1000MP MARK-V FIELD.
T his mod kit adds a few dB gain after the 70.455MHz IF amplifier and before
the mixer to the 8.215MHz. T his reduce the background noise and hi ss in the
MP audio output, coming from the 8.215MHz and 455kHz IF stages. The gain
at the lower frequency IFs is then reduced through a menu item, and the net
result i s a noticeable reducti on in the annoyi ng IF hiss and a reducti on in the
noi se floor of the receiver of 3 or 4dB. The net result i s a more sensi tive
recei ver which has a better, more pleasing sound. If the INRAD ROOFING
filter with enough IF gain is install ed in the radio, this IF Modul can not be
i nstalled.
1 pc: 1 390 Kč
RoHS
Fil ter 6000Hz/-6dB, 8215kHz, AM, shape factor 1.5. Fil ter is sol dered on little
board cal led SSB ADAPTER BOARD. You can instal one filter, replacing the
OEM 2.4kHz fil ter. You can instal l i n FT-920 more filters only when the
INRAD-920 SWITCHBOARD MOD ( GES08901740 ) wi ll be used.
GES08901946
1 pc: 3 490 Kč
INRAD-916 YAESU 73,6200MHZ
ROOFING FILTER FT1000D
INRAD VHF Bare Filter 73,6200MHz (>4kHz, 6 poles, 50 Ohm s) for
m ain RX FT1000D
RoHS
INRAD 2800Hz/455kHz YAESU FT890, FT900, FT990
Fil ter 2800Hz/-6dB, 455kHz, SSB. Crystal filter. Shape factor 1.5. Ulti mate
rej ection >80dB. Rippl e <2dB. Typical insertion loss <6dB. Zin/Zout 500
Ohms. Solder in fil ter; repl ace OEM fil ter and solder connections.
1 pc: 4 190 Kč
RoHS
INRAD-715C YAESU 455kHz 2800Hz
SSB FT1000, FT1000MP, MARKV
GES08900281
INRAD-710B YAESU 8215kHz
6000Hz AM FT1000, FT1000MP,
MARKV
GES08900283
GES08902077
1 pc: 2 990 Kč
RoHS
INRAD 6000Hz/8215kHz YAESU FT1000, FT1000MP, MARKV
INRAD-MPSRF YAESU 70.455MHZ
FT1000MP, MARK-V ROOFING
FILTER
Fil ter 6000Hz/-6dB, 8215kHz, AM, shape factor 1.5. Fi lter is soldered on
custom PC board. Pl ug in.
INRAD Roofing Filter 4kHz/70.455MHz for FT1000MP, MARKV
FT1000MP Series
GES08900286
1 pc: 3 490 Kč
RoHS
INRAD 2800Hz/455kHz YAESU FT1000, FT1000MP, MARKV
Fil ter 2800Hz/-6dB, 455kHz, SSB. Crystal filter. Shape factor 1.5. Ulti mate
rej ection >80dB. Rippl e <2dB. Typical insertion loss <6dB. Zin/Zout 500
Ohms. For Main and Sub receiver. Filter i s soldered on custom PCB. Pl ug in;
replace OEM filter.
INRAD-2311 YAESU 9000kHz
6000Hz AM FT7B, FT301, R530
GES08902127
INRAD 6000Hz/9000kHz YAESU FT7B, FT301, R530
1 pc: 4 190 Kč
RoHS
INRAD-716.1 YAESU 8215kHz
2800Hz SSB FT920
GES08901947
INRAD 2800Hz/8215kHz YAESU FT920. Replace directly OEM
2.4kHz filter
Fil ter 6000Hz/-6dB, 9000kHz, AM, 8 pol e, shape factor 1.5. Impedance
Zin=Zout= 500Ohm // 30pF
1 pc: 3 090 Kč
RoHS
INRAD-904 YAESU 45,7050MHZ
ROOFING FILTER FT847
T he FT 1000MP (MARK-V and FIELD inclusive) Roofing Fil ter help to reduce
the thi rd order IM products from multi ple strong signals in the 2 to 20kHz
region either si de of the tuned frequency. IMD dynami c range wil l be
i mproved 10dB or more for some signal spacing. Fi lter is assembled on PCB
with Hi gh Dynamic Range Feedback Ampl ifier, which cover the Filter loss plus
a dB or two.
GES08901848
1 pc: 4 290 Kč
RoHS
INRAD VHF Bare Filter 45,7050MHz (>4kHz, 6 poles, 50 Ohms) for
main RX FT847
INRAD-FT1000&FT1000D
73.6200MHZ YAESU ROOFING
FILTER
GES08901931
INRAD Roofing Filter 4kHz/73.6200MHz for FT1000, FT1000D
Fil ter 2800Hz/-6dB, 8215kHz, SSB, shape factor 1.6. Fil ter is soldered on little
board cal led SSB ADAPT ER BOARD. You can instal one filter, repl acing the
OEM 2.4kHz fil ter. You can instal l i n FT-920 more filters only when the
INRAD-920 SWITCHBOARD MOD ( GES08901740 ) wi ll be used.
1 pc: 3 090 Kč
RoHS
1 pc: 2 990 Kč
RoHS
INRAD-906 YAESU 47,0550MHZ
ROOFING FILTER FT980
GES08902080
1 pc: 4 290 Kč
RoHS
INRAD VHF Bare Filter 47,0550MHz (>4kHz, 6 poles, 50 Ohms) for
main RX FT980
1 pc: 2 990 Kč
RoHS
T his Roofing Filter for older YAESU models FT1000 and FT 1000D help to
reduce the third order IM products from multi ple strong signal s i n the 2 to
20kHz regi on either side of the tuned frequency. IMD dynamic range will be
i mproved 10dB or more for some signal spacing. Fi lter is assembled on PCB
with Hi gh Dynamic Range Feedback Ampl ifier, which cover the Filter loss plus
a dB or two.
INRAD FT-920 SWITCH BOARD
MOD
GES08901740
INRAD Board for FT920. Allows the use of one filter or two in
cascade
The FT920 Switch Board Mod allows the use of one fil ter or two i n cascade.
The switchi ng is done by a mini toggl e switch mounted on an L bracket under
a screw in the bottom cover. Two of these boards may be mounted in the
FT-920, provi ding fi lter selection from one switch for both CW and SSB. T he
boards are suppli ed pre-wired so the customer need do only a mini mum of
soldering. Please specify the mode when ordering. (Fi lters not incl uded.) T he
FT-920 Swi tch Board Mod i s pin compatible wi th our filters, so when orderi ng
filters for this product please specifi y the "bare fil ter -- no board" option. T he
FT-920 Swi tch Board Mod i s pin compatible with INRAD filters, so when
ordering fil ters for this product please speci fiy the "bare fil ter -- no board"
option.
1 pc: 1 990 Kč
RoHS
Measure Equipment
Attenuators
MFJ-762 ATTENUATOR
GES08900912
Attenuatr 81dB in 1dB s tep, 50Ohm , up to 170MHz, BNC-female
MFJ-259B ANTENNA ANALYZER
GES08901086
MFJ-39C CARRYING POUCH
HF/VHF 1.8-170MHz Antenna/SWR/RF Analyzer w/ LCD, Counter &
Meters
Carrying Pouch with window for MFJ269
The World's most popular SWR/RF analyzer just got incredi bly better and
gives you more value than ever! MFJ-259B gives you a complete pictures of
your antenna's performance. You can read antenna SWR and Complex
Impedance 1.8 to 170MHz Read Complex Impedance as series resistance
and reactance (R+jX) or as magni tude (Z) and phase (degrees). You can
determi ne velocity factor, coax cable l oss in dB, length of coax and distance
to a short or open in feet. You can read SWR, return loss and reflecti on
coefficient at any frequency si multaneously at a single glance. Also read
inductance in uH and capacitance i n pF at RF frequenci es. Large
easy-to-read two line LCD screen and side-by-side meters clearly display your
information. Built-in frequency counter, Ni-Cad charger circui t, battery saver,
low battery warning and smooth re-duction drive tuning and much more. Very
easy to use. Just set the bandswi tch and tune the dial - just like you
transcei ver. SWR and Compl ex Impedance are di splayed instantly. Here's
what you can do - fi nd your antenna's true resonant frequency, trim dipoles
and verticals. Adj ust your Yagi, quad, loop and other antennas, change
antenna spacing and hei ght and watch SWR, resistance and reactance
change instantly. You'll know exactly what to do by simpl y watching the
display. Perfectly tune cri tical HF mobi le antennas in seconds for super DX without subjecti ng your transcei ver to hi gh SWR. Measure your antenna's 2:1
SWR bandwidth on one band, or analyze mul tiband performance from 1.8 to
170MHz. Check SWR outside the ham bands without violating FCC rules.
Take the guesswork out of building and adjusting matching networks and
baluns. Measure distance in feet to a short or open in faul ty coax. Measure
length of a roll of coax, coax loss, velocity factor, i mpedance. Measure
inductance and capacitance. Measure resonant frequency and approxi mate
Q of traps, stubs, transmissi on lines, RF chokes, tuned circuits and baluns.
Adj ust your antenna tuner for a perfect 1:1 match without creating QRM. T he
MFJ-259B is a complete ham radi o test stati on including - frequency counter,
RF signal generator, SWR Analyzer, RF resistance and Reactance Analyzer,
Coax Anal yzer, Capaci tance and Inductance Meter and more. As external
power suppl y we recommend our MW 12V/0,5A GES07506809 or other.
1 pc: 6 990 Kč
GES08900694
Tote Your MFJ269 anywhere. This custom carying case has pocket wi th
securi ty cover for caryi ng di p coils (MFJ66), adaptors and accessories.
1 pc: 490.00 Kč
Action
RoHS
MFJ-66 ANALYSER COIL SET
GES08900894
Analyzers dip meter coils (HF/VHF). For
MFJ209,MFJ249,MFJ259,MFJ269
Dip-Meter Adapter (coils set) for SWR analyzer MFJ-209, MFJ-249, MFJ-259B,
MFJ-269.
1 pc: 660 Kč
RoHS
Action
RoHS
MFJ-269 ANTENNA ANALYZER
GES08901087
HF/VHF/UHF 1.8-170/415-470MHz Antenna/SWR/RF Analyzer w/
LCD, Counter & Meters
Dummy Loads
MFJ-260CN DUMMY LOAD
GES08901060
Dum my Load 0-650MHz/50Ohm; 90Wcont. (300W/30sec.m ax);
N-female connector
1 pc: 2 390 Kč
RoHS
Antenna Analyzers
MFJ-208 ANTENNA ANALYZER
GES08901085
VHF SWR Antenna Analyzer 138-156MHz. 178x51x51mm
1 pc: 2 650 Kč
RoHS
MFJ-269 covers 1.8 to 170 MHz and 415 to 470 MHz. It i ncludes al l the
features of the MFJ-259B, the world's most popular SWR Analyzer plus much
more. Large easy-to-read two l ine LCD displ ay and side-by-side meters clearly
display your informati on Built-in Ni-Cad/Ni -MH charger circui t, battery saver,
low battery warning, smooth reduction dri ve tuning. Use as si gnal source for
testing/alignment. Built-in CoaxCalcul ator - calcul ates coax line length in
feet given coax l ength i n electrical degrees and vice versa for any frequency
and any veloci ty factor (great for building matching secti ons and phasi ng
lines). New 12-bit A/D converter gi ves much better accuracy and resol uti on
than common 8-bit A/D converters. Very easy to use. Just set the bandswitch
and tune the dial - j ust li ke your transcei ver. 1.8 to 170MHz range features
MFJ-269 gives you a compl ete picture of you antenna. Read antenna SWR
and Complex Impedance 1.8 - 170 MHz. Buil t in frequency counter. Read
Complex Impedance as series equi valent resi stance and reactance (Rs+jXs) or
as magni tude (Z) and phase (degrees). Also read parallel equivalent
resi stance and reactance (Rp+jXp). You can determine velocity factor, coax
loss in dB, length of coax and di stance to short or open i n feet. You can read
SWR, return l oss and reflecti on coefficient at at any frequency simultaneously
at a single glance. Also read match effi ci ency. Also read inductance in UH
and capacitance in pF at RF frequencies. You can measure SWR and l oss of
coax with any characteristic impedance from 10 to over 600 Ohms, includi ng
50, 51, 52, 53, 73, 75, 93, 95, 300, 450 Ohms. For more i nformation see
MFJ-259B. New 415 to 470 MHz Range features. Just plug i n your UHF
antenna coax, set the frequency and read SWR, return loss and reflecti on
coefficient si multaneously. You can read coax cable loss in dB and match
efficiency. You can test and tune stubs and coax l ines. You can manual ly
determi ne veloci ty factor and impedances of transmission l ines. You can
adjust and test RF matching networks and RF ampli fiers wi thout appl yi ng
power. Has easy-to-read LCD logarithmi c SWR bargraph and SWR meter for
quick tuning. Take it anywhere Full y portabl e take i t anywhere - remote si tes,
up towers, on DX-pedi tions. Built in "N" connector Free N-to-SO-239 adaptor.
Use 10 pcs of alkaline batteries (not i ncluded) - R3 ALKALINE SANYO or AA
Ni-MH or AA Ni-Cd rechargabl e types UM 3 GES07602643 . T heir capaci ty
will suffice for 3 to 15 hours type depending. For external power supply we
recommend our type MW 12V/0,5A GES07506809 or other.
1 pc: 10 350 Kč
RoHS
1 pc: 1 330 Kč
RoHS
MFJ-264N DUMMY LOAD
GES08901061
Dum my load 0-650MHz 100W/10m in.(1.5kW/10sec.max.),
N-female connector
Dummy Load 50 Ohms. VSWR l ess than 1.3:1 at less than 650 MHz. Power
dissipation 1500W for less than 10 seconds or 100 Watts for 10 minutes.
Vol tage gradient 10 kV/inch (390V/mm). Operating temperature up to 350°C.
Frequency range 1-650 MHz, usable to 750 MHz.
1 pc: 2 280 Kč
RoHS
DL-650M
GES08901598
Dum my Load 0-650MHz 100W cont.(1500W/20sec); SWRmax=1.5;
UHFfemale
1 pc: 2 120 Kč
RoHS
DL-300M
GES08901596
Dummy Load 0-150MHz 300W(20sec); 50Ohm ; SWRmax=1.5:1;
0,25kg; UHFfemale
MFJ-873 SWR/WATTMETR
GES08901096
125-525 MHz Grandm aster SWR/Wattmeter (AVG, Peak)
5W/20W/200W
AMERITRON - Tubes PA
AL-811XCE PA 600W 160-10M WITH
TUBES
PA 600Wout (75Win); 3x811A tbs; full QSK; 160-10m ; 41x35x21cm;
15kg; 230VAC
1 pc: 1 325 Kč
RoHS
MFJ-250X DUMMY LOAD
GES08900304
GES08901059
MFJ Dum my Load 1kW without oil
1 pc: 2 120 Kč
RoHS
PM-30UV
GES08901622
Wattmeter 144/220/440MHz;30W and 300W;average/peak
power;135x146x89mm
Before operating fill the ADL-1500X with transformer oi l. DO NOT USE ANY
TYPE OF MOTOR OIL. Proper oil is the type "T ransformatorovy olej N"
suppli ed by the company Ecolube s.r.o. T he Ecolube web-shop i s on the web
address www.oleje.cz
1 pc: 1 390 Kč
RoHS
Power and SWR Measure Equipment
Has UHF-female connectors.
MFJ-267 DUMMY LOAD,
SWR/WATTMETER
1 pc: 2 650 Kč
GES08901090
RoHS
Dummy Load with SWR/Wattm eter up to 54MHz; Dum y Load
100W/10m in - 1,5kW/10sec
PA - RF Power Amplifiers
AMERITRON - Solid State PA
ALS-500MXCE
GES08900303
PA 500Wout / 70Win; Model 160-10m; Mobile Solid State; 13.6 VDC
/ 80A
1.5 kW Dry Dummy Load has built-in preci sion, true peak-readi ng
SWR/Wattmeter switchable to external antenna. World's most versatile 1.5 kW
dummy l oad has a built-in true peak readi ng SWR/Wattmeter that you can
switch and use independently. You'll find tons of uses. T une up your
transcei ver, linear amplifier, or antenna tuner i nto a safe 50 Ohm dummy
load at full power. Then instantl y switch to your antenna and monitor SWR,
forward, and reflected power. Use for testing/tuning transmitters, transceivers,
ampl ifiers, antenna tuners, baluns, transformers, filters, matching networks,
coax, stubs, transmissi on lines, and antennas. T he 50-Ohm dry dummy load
works DC to 60 Mhz. SWR is bel ow 1.3:1 at 30 MHz. Can handle 100 Watts for
ten mi nutes or 1500 Watts for ten seconds. Comes with power derating curve.
Extra-large three-inch lighted Cross-Needle Meter reads SWR (1:1 to 8:1),
forward, and reflected power simultaneously. Reads true peak PEP or average
power on 300/3000 Watts forward and 60/600 Watts reflected power ranges
1.8-54 MHz. High accuracy comes from a carefull y designed directional
coupler, an accurate active-peak reading circui t and a precision d'Arsonval
meter movement. RF tight perforated aluminum cabinet. 4 W x 3 H x 10 D
inches
1 pc: 4 240 Kč
RoHS
MFJ-844 SWR/WATTMETR
GES08901091
Compact Dual Band 144/440 SWR Meter
Version 160-10m.
1 pc: 27 800 Kč
RoHS
ALS-500MRXCE
GES08901827
PA 500Wout / 70Win; 160-10m; Mobile Solid State; 13.6VDC/80A;
with remote control
Sol ide State mobile PA wi th Remote Control
1 pc: 28 590 Kč
RoHS
Ameritron Al -811 li near ampl ifier gives you plenty power to bust thru QRM.
You get a quiet desktop l inear thats so compact itl l sl ide right into your station
-- youl l hardl y know i ts there ... unti l QRM sets in. Conveniently plug it into
your nearest 120 VAC outlet -- no special wiring needed. Three tough 811A
transmitti ng tubes, extra heavy duty power supply, all HF band coverage,
pressuri zed ventil ati on, tuned i nput, dual illuminated meters, adjustable ALC
& more. The fi rst 600 watts make the difference T he Al-811 gives you 600
watts PEP output -- thats nearly 2 full S-units over your barefoot ri g. That
could mean the difference between hearing, "Youre Q-5 armchair copy" and,
"Sorry cant copy you, too much QRM." Now you wont have to stand aside
whil e the "bi g guns" steal your DX. Youll be able to log some of those stations
first. Goi ng from 600 watts to the ful l legal l imit gives you less than one S-unit
i ncrease. But i s that fraction of an S-uni t worth the 3 or 4 ti mes more money
i tll cost you? AL-811 gi ves you a powerful punch at a price thats easy on your
wall et. All band, Al l mode coverage The AL-811 covers al l HF bands. T heres
no compromise on WARC and most MARS bands -- you get 100% rated
output. You can operate the AL-811 on all modes. Get 600 watts output PEP
SSB and 500 watts output CW. You even get 400 watts on demanding
conti nuous modes like RTTY, SSTV, FM and AM. How the low cost 811A tube
resists premature fail ure -- even when your amplifier is mistuned First theyre
constructed with widely spaced elements that minimize the chance of
touching and causing a short -- even i f the plate gets hot enough to melt.
Second they use a di rectl y heated thoriated tungsten filament cathode that
prevents the el ectron emitting layer from i nstantly stripping off -- even if
mistuning causes a sudden, sever current overload. The Ameri tron AL-811 is
excellent for the newcomer because its tough enough to withstand
momentary mistuni ng. And the tubes are so i nexpensive that you can repl ace
one for mere pocket change. T he Ameritron advantage: Extra heavy duty
power suppl y gi ves you peak performance year after year The heart of the
AL-811 power supply i s its heavy duty power transformer with high sil icon steel
core weighi ng a hefty 17 pounds. A full wave bri dge using 52.5 ufd of total
capaci tance (four 210 ufd, 470 volt capacitors) produces 1500 volts under full
l oad and 1700 volts no load. Thats excellent high voltage regul ati on! Full
hei ght computer grade filter capacitors with screw terminal s are used -- not
short stubby. l ight duty soldered-in "hi gh technology" capacitors that cant
dissipate the heat generated by high current. Rectifier diodes are rated for a
massive surge current of 200 amps. They wont blow even if you accidentall y
short the high voltage supply. Wire wound, 7 watt, 50 K ohm equalizing
resistors safely protect each filter capacitor -- not 2 watt, 100 K ohm carbon
composi tion resistors that can open and cause your fi lter capacitors to
explode or fail. The Ameritron AL-811 power supply i s built tough so you get
peak performance year after year. Tuned input provi des excel lent l oad for any
rig A Pi -Network tuned i nput provides a 50 ohm load for your ri g. Even fussy
solid state ri gs can deliver their full drive to AL-811. Low loss sl ug tuned coils
-- tunabl e from the rear panel -- l et you optimize performance. High quality
l ow dri ft sil ver mica capacitors mai ntain proper tuning. Output tank: optimum
Q on each band the low loss pi-network output tank of the AL-811 has been
carefull y desi gnated for optimum Q on each band and built with quali ty RF
components. The result i s peak performance over each band, wide
i mpedance matching range and exceptionally smooth tuning wi th
effi ci enci es close to 70%. Even a 3:1 SWR load wont damage the tubes or
tank components. A ball bearing vernier reduction dri ve makes plate tuning
preci se and easy. Qui et pressuri zed venti lation keeps your tubes safel y cooled
A qui et blower pressurizes the cabi net with a large volume of air fl ow. It keeps
the 811A tube temperature well below the tube manufacturers rating -- even
with a key down carrier at 400 watts output -- without the overwhelming noise
of oversized fans. Two illuminated meters Two illuminated meters give you a
clear picture of your AL-811 operating condi tions so you can tell right away if
something is wrong. the Grid Current meter continuously check for improper
l oading. The other meter switches between high vol tage and plate current to
warn of abnormal conditions. Ameritron exclusi ve Adapt-A-Volt power
transformer Too high line voltage stresses components and causes them to
wear out and fail. Too low line voltage causes a "soft-tube" effect -- l ow
output and signal distortion. Ameri trons excl usive Adapt-A-Volt power
transformer has a special buck-boost wi nding that lets you compensate for
stressful hi gh line voltage and performance robbing l ow line voltage. T his
makes your components last longer and gives you peak performance -regardless of your line voltage. QSK Compatibl e For l ightning fast QSK
operation, use the optional external QSK-5, electronic PIN diode switch. Plus
More... An Operate/Standby switch l ets you run barefoot, but you can
i nstantly swi tch to full power if needed. A transmit LED tel ls you when your rig
i s keying your AL-811. A 12 VDC keyi ng rel ay makes it compatible with sol id
state and tube ri gs. Buil t-in back-pulse canceling diode protects your rigs
keying circuit. Shielded RF compartment. One year limited warranty. UPS
shippable. Shi pped with transformer install ed and wired for 220/240 VAC.
T his ampl ifier is CE certifi ed. Made i n USA Made in the USA. At Ameri tron,
we dont j ust ship amplifiers we build them to last! Ameritron AL-811 Variants
600 W output (3 x 811A tubes) 800 W output (4 x 811A tubes) 800 W output (4
x 572B tubes) Output 600W / 800W / 800W US 120V AL-811 / AL-811H /
AL-811HD Export 220/240V AL-811X / AL-811HX / AL-811HDX Export
220/240V CE certified AL-811XCE / AL-811HXCE / AL-811HDXCE Export
120V w/10 Meters AL-811Y / AL-811HY / AL-811HDY It's perfect wi th
Ameritron MFJ-962D Antenna Tuner.
1 pc: 21 995 Kč
Thi s new compact VHF/UHF SWR and Power meter is perfect for mobile
hams. Handles 200 Watts and measure SWR and Power in three power
ranges: 15W, 60W, and 200 Watts. A multi-colored white, orange and black
meter makes for easy reading. Meter i s extra l arge and highly visible. Covers
144 and 440 MHz. Insertion l oss i s 0.3dB or lower with 50 Ohm impedance.
Has SO-239 connectors. Compact si ze lets you put it just about anywhere in
your operating posi tion. 3.75Wx3Hx1.25D inches. Great for HTs or mobile
rigs. Made of die cast metal with qual ity connectors. It'll gi ve you years of use.
1 pc: 1 890 Kč
RoHS
RoHS
AL-811HXCE PA 800W 160-10M
WITH TUBES
GES08900305
PA 800Wout (75Win); 4x811A tbs; full QSK; 160-10m; 41x35x21cm;
16kg; 230VAC
Only the AMERITRON AL-811H gi ves you four full y neutralized 811A
transmitting tubes. You get absolute stabil ity and superb performance on
higher bands that can’t be matched by un-neutrali zed tubes. AMERITRON
mounts the 811A tubes vertical ly, not horizontally, to prevent hot tube
elements from saggi ng and shorting out. Others, using potenti all y damagi ng
horizontal mounting, require hard-to-find 811A tubes to retard harmful
sagging and shorting. Powerful 20 CFM computer grade fan, not an open
frame phonograph motor, draws in cool air to pressurize the cabinet and
efficiently cool your 811A tubes for an extra l ong l ife. You also get efficient
ful l-size heavy duty tank coils, computer grade capacitors, heavy duty hi gh
silicon core power transformer, slug tuned input coils, operate/standby switch,
transmit LED, ALC, dual meters, QSK compatibili ty with QSK-5 option and
much more! SPECIFICAT IONS: • Output power: 800 Watts PEP, 600 Watts
CW. • All Band Operati on: Covers 160-15 Meters incl uding WARC bands. Can
be user modifi ed for12 and 10 Meters. • Four 811A Tubes: Uses four rugged,
ful ly neutralized low cost 811A PA tubes. • Vertical Tube Mounti ng: Prevents
shorting of tube filament/grid, prolongs tube l ife. • Full y Neutrali zed:
Improves stabil ity and performance on higher bands. • Input T une Circuit:
Adj ustabl e rear panel slug tuned i nput ci rcuit. • ALC Control : Built-in
adjustable ALC control. • Vernier Reduction Drives: Tuning and loadi ng
reducti on drives make tuning smooth and easy. • Dual Illumi nated Meters:
Moni tor vital operating functions. • Heavy Duty Power Supply: 17 pounds,
high sili cone steel core transformer and computer grade filter capacitor gives
1700 Volts high voltage at no load and 1500 Volts at full l oad. Multi-Voltage
Operation: User selectabl e for 100/110/120/210/220/230 VAC operation.
Shi pped with transformer install ed and wired for 120 VAC for domestic model
or 240 VAC for export model. • Air-Cooled: Quiet pressuri zed ventil ati on
keeps tubes safely cooled. QSK Compatible: Optional external el ectroni c pin
diode Transmit/Receive swi tch. QSK-5 • Attractive Lexan front decal • One
Year AMERIT RON warranty. • Dimensions: 8 Ľ" x 13 ľ" x 15 ˝". • Operati ng
Weight: 32 lbs. • Made in USA Made in the USA. At Ameritron, we dont just
ship ampli fiers we build them to l ast! Ameritron AL-811 Variants 600 W output
(3 x 811A tubes) 800 W output (4 x 811A tubes) 800 W output (4 x 572B tubes)
Output 600W / 800W / 800W US 120V AL-811 / AL-811H / AL-811HD Export
220/240V AL-811X / AL-811HX / AL-811HDX Export 220/240V CE certifi ed
AL-811XCE / AL-811HXCE / AL-811HDXCE Export 120V w/10 Meters AL-811Y
/ AL-811HY / AL-811HDY It's perfect with Ameritron MFJ-962D Antenna Tuner.
1 pc: 21 990 Kč
Action
RoHS
AL-80BXCE
GES08900306
PA >1kW SSB PEP(800W CW)/85Win; 3-500 tube; 160-10m ;
230VAC
AMPLIFIER, 1KW, ONE 3-500Z T UBE, EXPORT, CE Ameritrons l egendary
AL-80A kilowatt ampl ifier has been completely redesigned and extensively
improved. T he all New AL-80B kil owatt output desktop linear can double your
average SSB power output with high-level RF processi ng usi ng Ameritrons
exclusi ve Dynami c ALC. You get cooler operati on because the AL-80Bs
exclusi ve Instantaneous RF Bias completel y turns off the 3-500ZG tube
between words. It saves hundreds of watts wasted as heat. You get up to a full
kilowatt PEP output from a whisper quiet desktop linear. Its a compact 8.5" x
15.5" x 14.5" and plugs into your nearest 120VAC outl et. Covers all bands
160-15 meters, includi ng WARC and MARS (user modified for 10/12 meters
with license). You get up to 1000 watts output on SSB, 800 watts output on
CW, 500 watts output on RTT Y, an extra heavy duty power supply, genui ne
3-500 tube, nearl y 70% efficiency, tuned input, Pi /Pi-L output, inrush current
protection, multi -voltage transformer, dual Cross-Needle meters, QSK
compatibility, Two Year Warranty, Made in USA, plus much more. Dynamic
ALC doubl es average SSB power T he AL-80Bs excl usive Dynamic ALC gives
you high-l evel low-di stortion RF processi ng. When activated, it can more than
double your average SSB power and produce up to 6 dB i mprovement in
intell igi bil ity. It maximizes your talk power without di stortion and splatter. A
convenient front panel control lets you adjust your output power level.
Instantaneous RF Bi as eliminates heat The AL-80Bs excl usive Instantaneous
RF Bias compl etely turns off the 3-500 tube (except fil aments) between words
and dots and dashes. it eli mi nates hundreds of watts wasted as heat to give
you cool er operation and l onger component li fe. Guts Heavy-Duty Power
Suppl y T he guts of the AL-80B i s its heavy duty power supply. A 26 pound
transformer usi ng a high silicone steel core, computer grade capacitors, heavy
duty bleeders and ten 3 amp, 1000 V power recti fiers gi ve you a stiff 2700
volts full y l oaded. Many amplifiers using two 3-500s use such small power
suppli es they dont deliver much more power output than the AL-80B.
Genuine 3-500ZG Tube The AL-80B uses a genuine 3-500ZG tube warranted
by the manufacturer -- not cheaper, less reliabl e 3-500s used by some
competitors. 70% efficiency The AL-80B is built on a rugged steel chassi s. It
has a separate RF compartment thats fully shielded to keep RF from leaki ng
out. Thi s keeps RFI and TVI to a mini mum. Superb RF desi gn and layout,
Hi-Q tank ci rcuit and commerci all y rated RF power components gi ve you
nearl y 70% plate effi ci ency over most of the amateur bands. You power goes
into your antenna instead of heating up your ampl ifier. A whisper quiet
internal fan draws in cool air over power supply components and pressurizes
the 3-500 tube compartment to remove heat for longest li fe. Tuned Input lets
your rig deli ver full output A 50 ohm broadband Pi-Network tuned i nput i s
used. Even the fussiest sol id state transmitter wi ll deli ver full power to your
AL-80B. Low loss slug tuned coils -- tunable from the rear panel -- l et you
optimize performance. Pi/Pi -L Output Network A careful ly designed Pi/Pi-L
output network using the optimum Q for each band gives you exceptional ly
smooth tuning, extremely wide matching range, ful l band coverage and peak
performance at all power levels. Bal l bearing venier reduction dri ves with
loggi ng scal es on both the pl ate and load controls make tuning precise and
easy. It also lets you rapidly retune to your favorite frequency. Step-Start
Inrush Protection When you first turn on your amplifi er, a massive inrush
current fl ows. Your house lights fl icker as you hear a l oad "thump" from your
ampl ifier. This terrible inrush current stresses all your power supply
components to their limits. Your cold tube filament suffers abusi ve thermal
shock. Eventuall y, this massive inrush current will damage your amplifi er. T he
AL-80B speci al Step-Start Inrush Protection stop damagi ng i nrush current. By
starting your AL-80B through a 10 ohm current limiti ng resistor, then shorti ng
the resistor wi th a relay, the AL-80B gives you a start up sequence thats easy
on your tube and power supply components. Mul ti-Vol tage Power Transformer
Excessive line voltage stresses components and causes them to wear out. Low
line vol tage causes a "soft-tube" effect -- low output and signal distortion.
Ameri trons excl usive Multi-Voltage Power Transformer lets you optimize for
different line voltage. Select from 14 different pri mary vol tages from 90 - 140
VAC and 205 to 250 VAC. T he high voltage secondary can be wired to
reduce plate voltage for efficient operation below 400 watts for use outsi de
the USA. Dual Illumi nated Cross-Needle Meters Ameritrons dual il luminated
cross-needl e meters give you four separate meters to moni tor your operati ng
conditi ons -- you can tell ri ght away i f something is wrong. Grid current, plate
current and forward PEP output power are continuously monitored to tel l you
of improper loadi ng and abnormal conditions. The fourth meter can be
switched to monitor you 3-500 tube DC plate voltage, refl ected PEP power
and the SWR of your antenna, ALC voltage to your ri g and the grid current
that starts ALC acti on -- you get a clear operati ng picture of your AL-80B.
QSK Compati ble For l ightning fast QSK operation use the opti onal Ameritron
electronic PIN di ode QSK switch. Get the external QSK switch (QSK-5) or the
Internal Switch (QSK-5PC). Plus More... An Operate/Standby switch lets you
run barefoot, but you can i nstantly switch to full power if you need i t. Has
transmit LED; 12 VDC, 200 mA accessory jack; 12 VDC keying relay for solid
state and tube rigs; tough, nearly i ndestructible Lexan front panel . Shi pped
with transformer install ed and wired for 120 VAC. Draws 12 amps at 120 VAC.
Two Year Warranty: In the unlikely even that there are defects in materi als or
workmanship Ameritron will fi x it free for 2 years. T he 3-500 tube is covered
by the tube manufacturers warranty.
1 pc: 43 590 Kč
RoHS
AL-80BXQCE
GES08900307
PA >1kW SSB PEP(800W CW)/85Win;3-500 tube;QSK5PC;160-10m;230VAC
AMPLIFIER, 1KW OUTPUT,3-500Z, QSK, 240V CE Ameritrons legendary
AL-80A ki lowatt ampl ifier has been completel y redesigned and extensivel y
i mproved. The all New AL-80B kil owatt output desktop linear can double your
average SSB power output with high-level RF processing usi ng Ameritrons
excl usive Dynamic ALC. You get cooler operation because the AL-80Bs
excl usive Instantaneous RF Bi as completely turns off the 3-500ZG tube
between words. It saves hundreds of watts wasted as heat. You get up to a full
ki lowatt PEP output from a whisper qui et desktop l inear. Its a compact 8.5" x
15.5" x 14.5" and pl ugs into your nearest 120VAC outl et. Covers all bands
160-15 meters, i ncluding WARC and MARS (user modified for 10/12 meters
with license). You get up to 1000 watts output on SSB, 800 watts output on
CW, 500 watts output on RTT Y, an extra heavy duty power supply, genuine
3-500 tube, nearly 70% efficiency, tuned input, Pi /Pi-L output, inrush current
protecti on, multi-voltage transformer, dual Cross-Needle meters, QSK
compatibi lity, Two Year Warranty, Made in USA, plus much more. Dynami c
ALC doubles average SSB power The AL-80Bs exclusive Dynamic ALC gives
you high-level l ow-distortion RF processing. When acti vated, i t can more than
doubl e your average SSB power and produce up to 6 dB i mprovement in
i ntelli gibili ty. It maxi mi zes your tal k power without di stortion and splatter. A
convenient front panel control lets you adjust your output power level.
Instantaneous RF Bi as eliminates heat The AL-80Bs excl usive Instantaneous
RF Bias completely turns off the 3-500 tube (except fil aments) between words
and dots and dashes. it eliminates hundreds of watts wasted as heat to give
you cooler operation and longer component life. Guts Heavy-Duty Power
Supply The guts of the AL-80B i s its heavy duty power supply. A 26 pound
transformer using a high si licone steel core, computer grade capacitors, heavy
duty bleeders and ten 3 amp, 1000 V power recti fiers gi ve you a stiff 2700
volts fully l oaded. Many amplifi ers using two 3-500s use such small power
supplies they dont deliver much more power output than the AL-80B.
Genuine 3-500ZG T ube T he AL-80B uses a genui ne 3-500ZG tube warranted
by the manufacturer -- not cheaper, l ess reliabl e 3-500s used by some
competitors. 70% efficiency The AL-80B i s built on a rugged steel chassi s. It
has a separate RF compartment thats fully shielded to keep RF from leaking
out. Thi s keeps RFI and TVI to a mi nimum. Superb RF design and l ayout,
Hi-Q tank circuit and commercially rated RF power components give you
nearly 70% plate effi ci ency over most of the amateur bands. You power goes
i nto your antenna instead of heating up your ampli fier. A whi sper qui et
i nternal fan draws in cool air over power supply components and pressurizes
the 3-500 tube compartment to remove heat for l ongest li fe. Tuned Input l ets
your ri g deli ver full output A 50 ohm broadband Pi-Network tuned i nput is
used. Even the fussiest soli d state transmitter wi ll deliver full power to your
AL-80B. Low loss slug tuned coils -- tunable from the rear panel -- let you
optimize performance. Pi /Pi-L Output Network A careful ly designed Pi/Pi -L
output network using the optimum Q for each band gives you excepti onall y
smooth tuning, extremely wide matching range, full band coverage and peak
performance at all power l evel s. Ball bearing veni er reduction drives wi th
l ogging scal es on both the pl ate and load controls make tuning preci se and
easy. It also lets you rapidly retune to your favorite frequency. Step-Start
Inrush Protection When you first turn on your ampl ifier, a massi ve i nrush
current fl ows. Your house l ights fli cker as you hear a l oad "thump" from your
ampli fier. This terrible inrush current stresses all your power suppl y
components to thei r limits. Your cold tube filament suffers abusi ve thermal
shock. Eventuall y, this massive inrush current will damage your amplifi er. The
AL-80B speci al Step-Start Inrush Protection stop damaging i nrush current. By
starting your AL-80B through a 10 ohm current l imiting resistor, then shorting
the resistor with a relay, the AL-80B gives you a start up sequence thats easy
on your tube and power suppl y components. Multi-Voltage Power T ransformer
Excessive line voltage stresses components and causes them to wear out. Low
l ine voltage causes a "soft-tube" effect -- low output and signal di stortion.
Ameritrons exclusive Multi-Voltage Power Transformer lets you optimize for
different line voltage. Select from 14 different primary voltages from 90 - 140
VAC and 205 to 250 VAC. The high voltage secondary can be wired to
reduce plate voltage for efficient operation below 400 watts for use outside
the USA. Dual Il luminated Cross-Needle Meters Ameri trons dual ill uminated
cross-needle meters give you four separate meters to monitor your operating
conditions -- you can tell ri ght away if something is wrong. Grid current, plate
current and forward PEP output power are continuously monitored to tell you
of improper l oading and abnormal conditions. T he fourth meter can be
switched to monitor you 3-500 tube DC pl ate voltage, reflected PEP power
and the SWR of your antenna, ALC voltage to your rig and the grid current
that starts ALC action -- you get a clear operating picture of your AL-80B.
QSK Included For li ghtni ng fast QSK operation this ampl ifier includes the
Ameritron electronic PIN diode QSK switch Internal Swi tch (QSK-5PC). Plus
More... An Operate/Standby switch l ets you run barefoot, but you can
i nstantly swi tch to full power i f you need it. Has transmit LED; 12 VDC, 200
mA accessory jack; 12 VDC keying relay for sol id state and tube rigs; tough,
nearly i ndestructible Lexan front panel. Shipped with transformer i nstalled
and wired for 120 VAC. Draws 12 amps at 120 VAC. Two Year Warranty: In the
unl ikel y even that there are defects in materials or workmanship Ameritron
will fix it free for 2 years. The 3-500 tube i s covered by the tube
manufacturers warranty.
1 pc: 51 540 Kč
RoHS
AL-800XCE HF AMPLIFIER, 1.25KW,
800 TUBE, EXPORT, CE
GES08900308
PA >1.25kW SSB PEP (1kW CW) / 70Win; 3CX800A7 tube;
160-10m; 230VAC
Ameri tron’s compact AL-800 / AL-800H amps are both desktop li nears with
plenty of muscle! At 14.25" x 8.5 x14.5", the more compact AL-800 uses a
single 3CX800A7 to provide 1250 Watts PEP SSB and 850 Watts CW with 85
Watts typical drive l evel . And the AL-800 will even run from a 20-Amp 120
VAC li ne source i f desi red. AL-800 typi cally draws 17 Amps peak current at
120 VAC, or 8 Amps at 240 VAC and weighs just 51 l bs. For more power and
headroom, the AL-800H uses a pair of 3CX800A7 tubes to easily provi de
1500 Watts PEP/CW with a typical drive level of j ust 55 Watts. The AL-800H
draws 14 Amps peak current at 240 VAC (1500 Watts CW output) and wei ghs
just 52 l bs. Other than power differences, these amplifiers are very si mi lar in
features and operation. Both cover 160-15 Meters, and are modifiable to
cover 12/10 M with proof of your FCC license. Both incl ude a Step-Start™
input power circuit, a time delay circui t to allow for tube warm-up, thermal
overload protection, gri d current limiti ng to protect your tube(s), a
Dynami cBias™ circui t and a buil t-in mul ti-voltage (14 user-selectable AC li ne
voltages from 90-140; 200-250 VAC) heavy duty power transformer. Hefty 32
lb. grain orientated sil icone steel core transformer. Front panel monitori ng
and tuning functi ons are also virtually identical . Both amplifi ers include a
Standby/Operate swi tch for barefoot or full power operation, an ALC SET
control , Transmit and Faul t LEDs. Dual LED i llumi nated Cross-Needle meters
provide detail ed monitoring of amplifier performance. The left meter
continuously measures grid and pl ate currents, and the right meter
continuously measures peak RF output power on one scal e, and plate
voltage, Reflected power and SWR, ALC vol tage, and ALC adjustment set.
Quiet pressuri zed ventilation keeps tubes safely cooled. A Pi /Pi-Loutput
network gives you smooth tuning and wide matching range. Verni er reducti on
dri ves make tuning and loading adjustments smooth and easy. Output Power:
1250 Watts PEP, single 3CX800A7 Al l band operation: 160-15 meters
includi ng WARC bands. User modifiabl e for 12 and 10 meters. Genui ne
Eimac tube: Single Eimac 3CX800A7. Tuned input circuit: Adjustable sl ug
tuned input ci rcuit. Output network: Pi/Pi -L gives you smooth tuning and wi de
matchi ng range. Tube protection: Gri d current limiting circui t protects your
tubes. ALC control : Front panel adjustable, true ALC control . Vernier
Reducti on drives: T uning and l oading reduction dri ves make adjustments
smooth and easy. Heavy Duty power suppl y: Uses 32 lb. grain orientate sil icon
steel core transformer and hi gh capacitance computer grade fi lter capacitors.
Multi -voltage operation: 14 user selectabl e AC l ine vol tage from 90 - 140
VAC; 200-250 VAC. Air cooled: Quiet pressurized ventilation keeps tubes
safely cooled. Dual il luminated cross-needle meters: Two cross-needl e meters
that read peak forward power, reflected power, SWR, high vol tage, grid current
and plate current. Step-Start Inrush Protection: Stops damage to your
ampl ifier from inrush current. Attracti ve Lexan front panel decal Compact
Desktop Size One Year Warranty CE certi fied: T his product i s CE certified and
is compliant with all EU legi slation for use in the European Economic Area.
1 pc: 62 150 Kč
RoHS
AL-572XQ
GES08901167
PA 1.3kW SSB PEP (1kW CW)/75Win; 4x 572B tube; 160-10m;
QSK; 230VAC
HF AMP, 1300W, (4) 572B, QSK, 200/220/240,EXPORT Ameritrons new class
of Near Legal Li mi t Amplifi ers give you nearly full l egal SSB power output for
65% of the pri ce of a ful l l egal limit amplifier... and no one will ever know the
difference! You get 1300 Watts PEP SSB nominal power out on amateur
bands 160-15M. Four rugged 572B tubes give you near legal limit power and
instant 3 second warm-up time. T his whisper quiet, desktop linear plugs into
your nearest 120 VAC outlet - no speci al wiring needed. You get ...
Ameri trons excl usive Instantaneous RF Bias, dynamic ALC, Parasiti cKiller,
Step-Start Inrush Protection...heavy duty power supply... ful ly neutral ized
tubes...Pi /Pi-L network...tuned input...pressurized venti lation... dual lighted
Cross-Needle meters... multi-voltage power transformer... front panel ALC
control ....6:1 vernier reduction drives... much more! Four rugged Tubes T he
AL-572 uses four rugged fully neutralized tubes. Each tube has a heavy duty
Graphi te Anode, low l oss which Cerami c Base, superi or T itanium Getter and
legendary quality. Ameritrons excl usive ParasiticKi ller effectivel y suppresses
all parasitic oscillations. Near Legal Limit Power Output Youll typi cally get
1300 Watts PEP SSB, 1000 Watts CW continuous, 1000 Watts 1/2 hour PEP
two-tone test on all amateur bands from 160 through 15 Meters (WARC bands
and 10 Meters with reduced performance -- user modified for 10/12 Meters
with license). Instantaneous RF Bias el iminates heat Ameri trons excl usive
Instantaneous RF Bias completely turns off the 572B tubes between words
and dots and dashes. it eli mi nates hundreds of watts wasted as heat to give
you cooler operations nd l onger component li fe. Dynami c ALC doubles
average SSB power Ameritrons exclusive Dynamic ALC gives you high level,
low di stortion RF processi ng it can more than double your average SSB
power. Front panel control lets you adj ust output power. Heavy duty Power
Suppl y A heavy duty power supply usi ng a high sil icon steel transformer
delivers 2500 volts 0.7 amps with good regulation. The plate supply uses a
ful l wave doubl er, 200 amp peak surge current diodes, 7 watt, 50 K ohm wire
wound bleeder resi stors and a bank of high quality computer grade capaci tors
totali ng 26 ufd. Step-Start Inrush Protection When you turn on your ampl ifier,
a massive i nrush current flows. Eventually this current wil l damage your
ampl ifier. Ameritrons Step-Start Inrush Protection l imits damaging inrush
current to your power suppl y and tube filament. Thi s greatly extends the l ife
of your amplifier components and tubes. Pi/Pi -L Output Network The AL-572
Pi/Pi-L output network gi ves you exceptionally smooth tuning, wide matchi ng
range, full band coverage and peak performance at all power levels. Ball
beari ng vernier reduction drives on plate and load controls make tuni ng
precise and easy. Detail ed logging scales let you quickly return to your
favorite frequency. T uned Input l ets your ri g del iver ful l output A Pi-Network
tuned i nput using sl ug tuned coils provides a good 50 ohm load for your rig.
Even the fussiest sol id state ri g wi ll del iver full power to your AL-572. Whisper
Quiet pressurized cooli ng A whisper quiet internal fan draws in cool ai r over
power suppl y components and pressuri zes the tube compartment to remove
heat for longest life. To li ghted Cross-Needl e Meters Gri de current, plate
current and forward PEP output power are continuously monitored to tel l you
of improper l oading and abnormal conditions. A fourth scale switches among
peak refl ected power (and SWR), high voltage, ALC threshold and ALC output
voltage. Multi -Voltage Power Transformer Ameritrons Mul ti-Vol tage Power
Transformer has a uni que buck-boost winding. It lets you select from 14
pri mary vol tages centered on 115 and 230 VAC. You can match your AL-572
to your AC line vol tage so youll get peak performance and l ong component
life -- regardless of your li ne vol tage. QSK Included For l ightning fast QSK
operation thi s amplifier includes the Ameritron electronic PIN diode QSK
switch Internal Switch (QSK-5PC). Plus More! An Operate/Standby switch lets
you run barefoot, but you can instantly switch to full power i f you need it.
Transmit LED; 12 VDC, 200 mA accessory jack; 12 VDC keying relay for solid
state/tube rigs; tough, nearl y indestructibl e Lexan-over-aluminum front panel.
Shi pped with transformer install ed and wired for 220 VAC. Ameritron Warranty
In the unli kely even that there are defects in materials or workmanship,
Ameri tron will fix your AL-572 free for a full year. Made in the USA
AL-800HXCE
GES08900309
PA >1.5kW CW,SSB PEP/55Win; 2x 3CX800A7; 160-10m ;
QSK-5PC; 230VAC
HF AMPLIFIER, 1.5 KW+, 2X800 TUBES, EXPORT, CE Ameri tron’s compact
AL-800 / AL-800H amps are both desktop l inears wi th pl enty of muscl e! At
14.25" x 8.5 x 14.5", the more compact AL-800 uses a single 3CX800A7 to
provi de 1250 Watts PEP SSB and 850 Watts CW wi th 85 Watts typical drive
l evel . And the AL-800 wi ll even run from a 20-Amp 120 VAC line source if
desi red. AL-800 typically draws 17 Amps peak current at 120 VAC, or 8 Amps
at 240 VAC and weighs just 51 lbs. For more power and headroom, the
AL-800H uses a pai r of 3CX800A7 tubes to easi ly provide 1500 Watts
PEP/CW with a typical drive level of just 55 Watts. The AL-800H draws 14
Amps peak current at 240 VAC (1500 Watts CW output) and wei ghs just 52 l bs.
Other than power differences, these ampl ifiers are very si mi lar in features and
operation. Both cover 160-15 Meters, and are modifi able to cover 12/10 M
with proof of your FCC l icense. Both include a Step-Start™ input power
circuit, a time del ay circuit to allow for tube warm-up, thermal overload
protecti on, grid current l imiting to protect your tube(s), a DynamicBias™
circuit and a bui lt-i n mul ti-voltage (14 user-selectable AC line voltages from
90-140; 200-250 VAC) heavy duty power transformer. Hefty 32 l b. grain
orientated silicone steel core transformer. Front panel monitoring and tuning
functions are also virtually identical . Both ampli fiers include a
Standby/Operate switch for barefoot or full power operation, an ALC SET
control, Transmit and Fault LEDs. Dual LED il luminated Cross-Needl e meters
provi de detailed monitoring of amplifi er performance. The l eft meter
conti nuously measures grid and plate currents, and the right meter
conti nuously measures peak RF output power on one scale, and plate
voltage, Reflected power and SWR, ALC voltage, and ALC adjustment set.
Quiet pressurized ventilation keeps tubes safel y cooled. A Pi/Pi-Loutput
network gives you smooth tuning and wi de matching range. Vernier reduction
drives make tuni ng and loading adj ustments smooth and easy. Output Power:
1500 Watts PEP, double 3CX800A7 All band operation: 160-15 meters
i ncluding WARC bands. User modi fiable for 12 and 10 meters. Genuine
Eimac tube: Two Eimac® 3CX800A7. Tuned input circui t: Adjustable slug
tuned input circuit. Output network: Pi /Pi-L gi ves you smooth tuni ng and wide
matching range. Tube protecti on: Grid current limiti ng ci rcuit protects your
tubes. ALC control: Front panel adjustable, true ALC control. Verni er
Reduction drives: Tuni ng and loading reducti on drives make adj ustments
smooth and easy. Heavy Duty power supply: Uses 32 lb. grain orientate sili con
steel core transformer and high capacitance computer grade fil ter capacitors.
Multi-voltage operation: 14 user sel ectable AC li ne voltage from 90 - 140
VAC; 200-250 VAC. Ai r cool ed: Quiet pressurized venti lation keeps tubes
safely cooled. Dual ill uminated cross-needl e meters: Two cross-needle meters
that read peak forward power, refl ected power, SWR, hi gh voltage, gri d current
and pl ate current. Step-Start Inrush Protection: Stops damage to your
ampli fier from i nrush current. Attractive Lexan front panel decal Compact
Desktop Size One Year Warranty
1 pc: 89 900 Kč
RoHS
AL-82XCE PA 1500W 160-10M WITH
TUBES
GES08900315
PA >1.5kW CW,RTTY (>1.8kW PEP)/100Win; 2x 3-500Z tubes;
160-10m; 230VAC
1 pc: 57 990 Kč
RoHS
AMPLIFIER, 1500W, EXPORT, CE, TWO 3-500Z Ameritron's Dual 3-500Z
Amplifier The Ameri tron AL-82 Linear Ampli fier is designed to gi ve you years
of trouble free servi ce at the full legal output power limit. An 1800 watt
conti nuous commercial rated Hypersil transformer is standard with heavy duty
rectifiers in a full wave bridge supply with computer capaci tors. Two bias
setti ngs al low ei ther high efficiency RT TY and CW operation at 1500 watts of
output at nearly 70% pl ate efficiency or l ow distortion 1500 watts PEP, SSB
or SSTV output. Sil ver plated tank components provide hi gh efficiency
operation above 20 meters. The Pi-L tank circui t permits full impedance
matching capability over the enti re 160 meter band. T he tuni ng capacitors
and bandswitch have a 35% safety factor to virtually eliminate tank circuit
component failures, even under adverse operating condi tions. The cooling
system keeps the components and tube safely below the manufacturers
rati ngs, even while operating at 1500 watts output wi th a steady carri er. The
filament supply has inrush current limiti ng to i nsure maximum tube life.
Shielding and by-passi ng hel p prevent TVI and RFI at the hi gh power levels
i n the AL-82. T he AL-82 has two ill uminated meters. One is the Grid Current
Meter that provi des a conti nuous reading of the 3-500ZG grid current. This is
an Ameritron fi rst. Grid current indi cates proper amplifier performance better
than any other parameter. T he other i s a mul ti-meter that displ ays plate
voltage, plate current, peak R.F. output power and drive power/ALC detector
voltage. Some competing amplifi ers usi ng two 3-500ZGs cant del iver as
much power as the AL-82. Why? Because the li ghtweight power suppl ies they
use dont del iver enough high voltage to permit use of the ful l capabi lity of
the two 3-500ZGs. The AL-82 corrects thi s problem whil e stil l keeping the
price at a reasonabl e l evel . The power supply in the AL-82 has a commerci al
service rated 32 pound tape wound Hypersil transformer and heavy duty
rectifiers in a full wave bridge circui t with computer grade capacitors. No load
voltage is 3600 V; full load voltage 3300V -- better than most competing dual
3-500ZG ampl ifiers. Examine the features and component ratings of the
AL-82 is a well engineered amplifier, bui lt to gi ve you years of power house
service. AL-82 Specifications: Frequency coverage: 1.8, 3.5, 7, 14, 21 MHz
and WARC bands. Export/User modified models incl ude 28MHz. Input
Circui t:Adjustable pi-network, VSWR 1.2:1 or less at resonance. Output circuit:
Pi-L/Pi network. Input Bandwi dth: 20% for 2:1 VSWR or better. Effi ci ency:
CW/SSB nearly 70% Operating Weight: 76lb. Dimensions: 18 1/2"D x 17"W x
10"H Power Requirement: 240 VAC 50/60 Hz 15 Amperes. High Voltage:
3300 V full load, 3600 V no load.
1 pc: 80 690 Kč
RoHS
AL-82XQCE PA 1500W 160-10M
WITH TUBES
GES08900316
QSK-5PC
GES08902220
PCB KIT 2.5 KW, Pin Diode T/R QSK Switch
PA >1.5kW CW,RTTY (>1.8kW PEP) / 100Win; 2x 3-500Z; 160-10m;
QSK-5PC; 230VAC
AMPLIFIER, TWO 3-500Z, QSK, EXPORT, CE Ameritron's Dual 3-500Z
Ampli fier The Ameritron AL-82 Linear Ampl ifier is designed to give you years
of trouble free service at the ful l l egal output power li mi t. An 1800 watt
continuous commercial rated Hypersil transformer i s standard with heavy duty
recti fiers i n a full wave bri dge supply with computer capacitors. Two bias
settings allow either high effi ci ency RTTY and CW operation at 1500 watts of
output at nearly 70% plate efficiency or low distorti on 1500 watts PEP, SSB
or SSTV output. Si lver plated tank components provide high efficiency
operation above 20 meters. The Pi-L tank circuit permi ts full impedance
matchi ng capabili ty over the entire 160 meter band. The tuning capaci tors
and bandswi tch have a 35% safety factor to vi rtuall y eliminate tank ci rcuit
component failures, even under adverse operating conditions. T he cooli ng
system keeps the components and tube safely below the manufacturers
ratings, even while operating at 1500 watts output with a steady carrier. T he
filament supply has inrush current limiting to insure maximum tube li fe.
Shi elding and by-passing help prevent TVI and RFI at the high power l evel s
in the AL-82. The AL-82 has two il luminated meters. One is the Grid Current
Meter that provides a continuous reading of the 3-500ZG grid current. T his i s
an Ameritron first. Gri d current i ndicates proper ampli fier performance better
than any other parameter. The other is a multi-meter that displays plate
voltage, pl ate current, peak R.F. output power and drive power/ALC detector
voltage. Some competi ng amplifiers using two 3-500ZGs cant deliver as
much power as the AL-82. Why? Because the l ightweight power supplies they
use dont deliver enough high vol tage to permit use of the full capability of
the two 3-500ZGs. The AL-82 corrects this probl em whi le sti ll keepi ng the
pri ce at a reasonable level. The power supply i n the AL-82 has a commercial
service rated 32 pound tape wound Hypersil transformer and heavy duty
recti fiers in a ful l wave bridge circuit wi th computer grade capaci tors. No load
voltage is 3600 V; ful l load vol tage 3300V -- better than most competi ng dual
3-500ZG amplifi ers. Exami ne the features and component rati ngs of the
AL-82 is a wel l engineered ampli fier, built to give you years of power house
service. AL-82 Specifi cations: Frequency coverage: 1.8, 3.5, 7, 14, 21 MHz
and WARC bands. Export/User modifi ed model s include 28MHz. Input
Circuit:Adjustable pi-network, VSWR 1.2:1 or less at resonance. Output circuit:
Pi-L/Pi network. Input Bandwidth: 20% for 2:1 VSWR or better. Efficiency:
CW/SSB nearly 70% Operating Weight: 76l b. Di mensi ons: 18 1/2"D x 17"W x
10"H Power Requirement: 240 VAC 50/60 Hz 15 Amperes. High Vol tage:
3300 V full load, 3600 V no load.
Thi s self-contained AMERITRON QSK-5 Transmit/Receive Swi tch uses
electronic PIN diode switching to give you lightning fast QSK operation from
nearl y any HF li near amplifi er. It lets you use your linear ampli fier for hi gh
power QSK CW, for packet, AMT OR and any mode requiring extremel y fast
switching between transmit and recei ve. Installation is simple. Just pl ug in a
few cables to start enjoyi ng QSK. There is no complicated internal wiring.
The world’s most advanced QSK switch has new technol ogy that’l l make your
ampl ifier last l onger and prevent TVI, RFI and key clicks. AMERIT RON’s
exclusi ve AmpSaver™ (availabl e in QSK-5PC and QSK-5PCI) completely
turns off your power ampl ifier tube current between dots, dashes and words!
Thi s new QSK technology gets rid of unwanted power dissipation that causes
damagi ng heat. Your expensive amplifier runs cool er so every component in
your ampl ifier l asts longer. Our exclusive SureSwi tchTM handshaki ng
prevents “hot switchi ng” RF power. Prevents TVI, RFI, key cl icks and possible
damage to your amp. The QSK-5 is six times faster than a typical mechanical
vacuum rel ay “QSK” switch that can j ust barel y keep up with QSK transceivers.
As radios get faster and better, mechani cal swi tching just won’t be able to
switch fast enough. Unli ke noisy mechani cal vacuum rel ays, the QSK-5 i s
extremely qui et. There’s no relay chatter keeping you from enjoying QSK.
You won’t have to pay for QSK agai n if you buy another ampl ifier. Unpl ug the
QSK-5 and use it wi th your new amp. Handles 2500 Watts PEP and 2000
Watts CW in normal amateur servi ce when SWR is below 1.5:1. Handles 750
Watts on continuous carri er modes such as RTTY, SSTV, and FM. Optional
cooi ng fan (CF-5) allows sustained operation at 1500 Watts i n any mode. Use
with positi ve voltage keyi ng up to +25 Volts. 6" x 4" x 9 ˝". Internal QSK
Avail able for the following AMERIT RON model s: AL-80B, AL-1500, AL-1200,
AL-82, AL-800, AL-800H.
Microphones, Headphones, Headsets
Microphones
DM-045
GES07004637
Dynam ic microphone 50-16000Hz, 250Ohm., 1.3mV/Pa/1kHz
1 pc: 7 950 Kč
RoHS
QSK-5X
GES08901123
2.5 KW, Stand-alone Pin Diode T/R QSK Switch, 230V
Nostalgic dynamic mi crophone, in the look of the 50s/60s. For stage, speech
and vocal s. Of cardioid characteristic, neodymium magnet, chromium-pl ated
version. Including foam-padded plastic case. Technical Facts Microphones
Systemdyn./cardioid
Frequency
range50-16,000Hz
Impedance250?
Sensitivity1.3mV/Pa/1kHz
Max.
SPL130dB
Bodymetal,
si lver
Dimensions71x179x55mm Weight670g Connection, mi crophoneXLR
1 pc: 1 099 Kč
RoHS
RoHS
Use this QSK-5X Ameritron PIN TX/RX switching unit to give you li ghtni ng
fast QSK operati on from nearly any HF linear amplifier for extra quick
switching. Extremly fast (six ti mes faster than a typi cal mechanical vacuum
rel ay). For Packet Radio, AMTOR, CW and any mode requiri ng extremly fast
switching between transmit and receive. Prevents T VI, RFI and key cliks.
Handl es 2500W PEP or 2000W CW when SWR is below 1.5:1. Handl es 750W
on continuous carrier modes such RTT Y, SSTV and FM. T he optional cooli ng
fan sustai ned operation on 1500W in any mode.
DM-065
GES07004638
Dynam ic microphone 50-16000Hz, 250Ohm., 1.3mV/Pa/1kHz
1 pc: 10 590 Kč
RoHS
1 pc: 88 640 Kč
RoHS
Transmitting Tube 811A TUBE
GES08902219
Accessories for PA
Tube 811A from Ameritron - spare part 380-0811A
OKB-1
GES08901828
Interface cable for control of PA AMERITRON with YAESU FT857,
FT897
Nostalgic dynamic mi crophone, in the look of the 50s/60s. For stage, speech
and vocal s. Of cardioid characteristi c, l ow-noise on/off switch, chromiumplated versi on. Includi ng foam-padded plastic case. Technical Facts
Microphones
Systemdyn./cardi oid
Frequency
range50-16,000Hz
Impedance250? Sensitivity1.3mV/Pa/1kHz Max. SPL135dB Bodymetal, si lver
Dimensions54x175x68mm Weight550g Connection, mi crophoneXLR
1 pc: 1 159 Kč
RoHS
RoHS
DM-2800
GES13004374
Dynam ic microphone 50-18000Hz, 250Ohm., 1.5mV/Pa/1kHz
1 pc: 748 Kč
RoHS
Transmitting Tube 811A - MATCHED
PAIR OF TUBES
GES08902218
Matched Pair of 811A Tubes from Ameritron - spare part
380-0811A-2M
1 pc: 300.50 Kč
RoHS
ARB-704
GES08900332
Amplifier-Trans ceiver Interface for all transceiver
1 pc: 1 295 Kč
RoHS
RoHS
DM-70/SW
GES13001949
Dynam ic microphone 100÷10000Hz; 600Ohm .; black
1 pc: 1 590 Kč
RoHS
1 pc: 99.00 Kč
RoHS
RoHS
DM-88/BC
GES07000037
Dynam ic microphone 80-12000Hz, 500Ohm., anthracite
1 pc: 1 545 Kč
RoHS
1 pc: 399.00 Kč
RoHS
RoHS
PA desk microphones ECM-200
GES07004606
Table m icrophone, JACK 6,3, s upply 1,5V (AA)
WS-200/SK
GES07004629
Microphone wind shields of skin-coloured foam, for microphones
with dia.2-4mm
General Information Frequency range 60-12,000Hz Sensitivity 6mV/Pa/1kHz
Impedance 1kOhm S/N ratio > 40dB Admi ss. ambi ent temp. 0-40 °C Power
supply 1 x 1.5V batt. AA si ze Dimensions consol e housing only
75x25x110mm Total l ength of gooseneck 200mm Weight 380g Connecti ons
6.3mm plug
WS-300/SK
1 pc: 85.00 Kč
RoHS
RoHS
WS-150/SW
GES07004632
Microphone wind s hields of skin-coloured foam , for microphones
with dia.4-6mm
1 pc: 85.00 Kč
RoHS
RoHS
GES07004626
WS-100/SW
GES07004624
Microphone wind shields of black foam, for microphones with
dia.4-6mm , set 4pcs.
Microphone wind s hields of black foam, for m icrophones with
dia.6-8mm
RoHS
RoHS
For microphones with dia. 4-6mm Dimensions: dia. 11mm x 12mm Sui table
e.g. for ECM-500L/SK, ECM-501L/SK, HSE-60/SK, HSE-150/..., HSE-152/...
For microphones with di a. 6-8mm Dimensions: dia. 18mm x 32mm Suitable
e.g. for HSE-100
Microphone shields
WS-150/SK
1 pc: 730 Kč
RoHS
HM-30
GES07004476
Dynamic headband microphone 300-16000Hz, 1mV/500Ohm.,
black
1 pc: 399.00 Kč
1 set: 95.00 Kč
WS-100
RoHS
RoHS
GES07004623
1 pc: 115.00 Kč
RoHS
RoHS
GES07004627
Microphone wind shields of skin-coloured foam, for microphones
with dia.4-6mm, set 4pcs.
WS-10
GES07004622
Microphone wind s hields of black foam, for m icrophones with
dia.7-9mm
Microphone winds hields, clamp for stand
For microphones with di a. 7-9mm Dimensions: dia. 14mm x 15mm Suitable
e.g. for ECM-300L
1 pc: 299.00 Kč
RoHS
RoHS
WS-200/SW
1 pc: 29.00 Kč
GES07004628
Microphone wind shields of black foam, for microphones with
dia.2-4mm
1 set: 77.00 Kč
RoHS
RoHS
WS-300/SW
GES07004631
Microphone wind shields of black foam, for microphones with
dia.4-6mm
For microphones with di a. 2-4mm Dimensions: dia. 7mm x 15mm Sui table
e.g. for HSE-200
RoHS
RoHS
WS-30
For microphones with di a. 11-15mm Di mensi ons: dia. 30mm x 51mm
Suitable e.g. for ECM-200, PAM-10
1 pc: 85.00 Kč
RoHS
RoHS
GES07004630
Microphone wind s hields of black foam, for m icrophones with
dia.11-15mm
For microphones wi th di a. 4-6mm Dimensions: di a. 17mm x 29mm Sui table
e.g. for HSE-300...
1 pc: 109.00 Kč
RoHS
RoHS
1 pc: 25.00 Kč
RoHS
RoHS
WS-20
GES07004625
Microphone wind s hields of black foam, for m icrophones with
dia.12-14m m
For mi crophones with dia. 12-14mm Dimensions: dia. 20mm x 22mm
Suitable e.g. for ECM-3003, ECM-3005
1 pc: 20.00 Kč
RoHS
RoHS
WS-40
GES07004633
Microphone wind shields of black foam, for microphones with
dia.21-26mm
WS-5
GES07000039
Set of 5 microphone wind shields black, red, green, yellow, blue,
for m icrophones with dia.40-50mm
Set of 5 mi crophone wi nd shi elds, black, red, green, yellow and blue foam.
For microphones with dia. 40-50mm. Sui table e.g. for DM-2500 and
mi crophones of the same desi gn.
1 set: 199.00 Kč
RoHS
RoHS
For microphones with di a. 21-26mm Dimensions: dia. 39mm x 55mm
Sui table e.g. for DMG-600
1 pc: 29.00 Kč
RoHS
RoHS
WS-50
GES07004634
Microphone wind shields of black foam, for microphones with
dia.21-26mm
HEIL SOUND - Microphones for
amateur radio
GM-4 GOLD MICROPHONE
FULL-RANGE/HC4
GES08901463
HEIL The Gold Standard of Microphones. Broadcast Full-Range
and HC4 (DX Dream)
HM-IC HANDI MIC iC MICROPHONE
ICOM
GES08901646
HEIL Handy Microphone with IC electret (ICOM only) and PTT
T he Heil Handi Mic Pro Plus represents completel y new dynamic microphone
technol ogy designed for a wide range of professi onal appli cations such as
l ive sound, commercial broadcast, and sophisticated recordi ng. Its wide
frequency range outperforms the tired, 30+ year ol d i ndustry technology and
can withstand huge amounts of SPL. The end result is a microphone that can
answer the cal l to any appl icati on. The Handi Mi c Pro Plus is ideal for use
with tom drums where smaller microphones are needed, as well as i nside
Lesl ie speakers. The Handi Mic is perfect for an intervi ew microphone where
i ts small si ze makes i t a very low profi le microphone wi th great sound. Si nce
1982, Hei l Sound has been the l eading manufacturer of communi cations
microphones and has a paramount understandi ng of phasi ng. When properl y
applied, this knowl edge creates outstanding cardi oid patterns wi th
unbel ievable rear rejecti on that removes unwanted sounds that try to enter
from the off axis rear. The pattern control of the Heil Handi Mic Pro Plus is
outstandi ng. T his excepti onal performance is achi eved by using the i deal
combinati on of materials for the large l ow mass diaphragm and a speci al
mixture of neodymium, iron, and boron that gives the Handi Mic Pro Pl us the
strongest magnet structure availabl e. Special attention has been paid to the
phasing pl ug assembl y wi th equally pl aced ports that sense audi o from
behind, entering them out of phase. Thus, the Handi Mic Pro Plus produces a
very linear cardi oid pattern and reduces the proximity effect while achieving
perfect articulation. This new Heil element is usabl e i n extreme high sound
pressure levels and is immune to overl oad condi tions maki ng it perfect for
vocal and li ve sound applications. The Handi Mic Pro Plus i s supplied with a
standard 5/8" -27 mic cl ip and a foam windscreen. CC-1-XLR4 or CH-1adapter requi red to interface HM series microphone with your TCVR.
1 pc: 1 695 Kč
Final
RoHS
HM-12 HEIL GENESIS
GES07004668
HEIL Dynamic mcrophone for radiocomm unications, with PTT
s witch
For microphones with di a. 21-26mm Dimensions: dia. 42mm x 65mm
Sui table e.g. for ECM-100, ECM-600ST
1 pc: 29.00 Kč
RoHS
RoHS
WS-950
GES07004636
Microphone wind shields of black foam, for microphones with
dia.21-26mm
GM-4 has Cardioid Polar Pattern, i mpedance is 1000 Ohms. Microphone has
PTT switch and WIDE/NARROW switch. Frequency response WIDE i s
50Hz-16kHz/-3dB (+4dB/2000Hz, HC-4 element), NARROW i s 600Hz8kHz/-3dB (+4dB/2000Hz, HC-5 elemnt). Microphone has a XLR 4PIN male
connector and the CC-1-XLR4 adapter is requi red to interface mi crophone
with your T CVR.
1 pc: 3 995 Kč
Final
RoHS
GM ELITE - GOLD ELITE DUAL
ELEMENT MICROPHONE
GES07004654
HEIL The Gold Elite Microphon with two m icrofon elem ents and
PTT switch
CH-1 adapter requi red to interface HM series microphone with your TCVR.
T he new HM-12 mi crophone i s designed speci fical ly for amateur radio
communications. The high output full range ‘Genesis’ dynami c element is
desi gned to work with just about every amateur radio l ow impedance
transmitter. T he element is mounted i n a unique internal shock mount and
exhibits nearl y –35 dB of rear rejection, which reduces background and
ambient noise from the transmitted signal. The Heil HM–12 exhibi ts a very
natural audi o response from 80Hz – 14 kHz. T he traditional Heil +4 dB peak
centered at 2 kHz gives the new HM-12 excel lent voice articulation bal anced
with cl ean, cl ear low-end response produci ng a high quality AM, FM or SSB
si gnal. The ‘soft touch’ PT T swi tch i s wired to pi ns 3 and 4 for transmitter
control with the microphone signal fed to pins 1 and 2 of the four-pin XLR.
T he Heil HM -12 uses the HEIL CC-1-XLR4 Connecti ng Cables. The HM-12
microphone has an i nternal foam windscreen and incl udes a 5/8”-27
microphone cl ip that i s designed for our booms and desk stands.
1 pc: 1 880 Kč
RoHS
For microphones with dia. 21-26mm Dimensions: dia. 40mm x 154mm
Sui table e.g. for ECM-950
1 pc: 85.00 Kč
RoHS
RoHS
WS-3
GES07000038
Microphone wind shields of black foam, for microphones with
dia.40-50mm
The new Gol d Eli te microphone is desi gned and crafted speci fical ly for
amateur radio communications. It contai ns two disti nctly di fferent hi gh
performance dynamic elements that are availabl e at the fli p of a switch to
meet the di fferent types of communicati ons. T he WIDE posi tion has the HEIL
Elite full range element produci ng smooth articul ate 60Hz – 16 kHz audio
with the tradi tional Hei l +4 dB peak centered at 2 kHz. T his gives the new
Gold Elite excellent voi ce articul ati on along with its ‘big bottom’ low end that
is so i mportant for producing a well balanced, studio qual ity SSB signal . T he
NARROW position features the new Hei l HC-5.1 dynamic element. In 1982
Hei l Sound revol uti onized amateur radi o audi o with their tailored response
HC-4 and HC-5 as the radios had no transmit tone adjustments. All of today's
transmitters have so. New mic technology to meet today’s new DSP
technology. T he ‘soft touch’ PTT switch is wired to pins 3 and 4 for transmit
control . The microphone audio i s fed to pins 1 (shield) and 2 of the four pin
XLR. The Gold El ite uses the HEIL CC-1-XLR4 Connecting Cabl es. The Gold
Elite mi crophone comes to you with a foam wi ndscreen and a 5/8”-27
mi crophone clip that is designed for our booms and desk stands.
iCM HEIL microphone for ICOM
GES07004667
High-performance microphone specially designed for owners of
earlier Icom transceivers
1 pc: 4 320 Kč
RoHS
GM-VINTAGE MICROPHONE
For mi crophones wi th dia. 40-50mm Sui table e.g. for DM-2500 and
mi crophones of the same desi gn
GES08901641
HEIL The Gold Standard High Impedace Microphone for Vintage
Radios
1 pc: 129.00 Kč
RoHS
RoHS
WS-60
GES07004635
Microphone wind shields of black foam, for microphones with
dia.40-50mm
GM-VINTAGE Microphone has Cardioid Polar Pattern, impedance is 30.000
Ohms (buil t-in impedance transformer XT-1). Microphone has PT T switch and
WIDE/NARROW swi tch. Frequency response WIDE i s 60Hz-16kHz/-3dB
(+4dB/2000Hz), in the NARROW position the l ow end response rolls off.
Mi crophone has a XLR 4PIN male connector and the CC-1-XLR4 adapter i s
requi red to interface microphone with your TCVR.
1 pc: 4 270 Kč
RoHS
For microphones with di a. 40-50mm Dimensions: dia. 60mm x 70mm
Sui table e.g. for DM-2500
1 pc: 49.00 Kč
RoHS
RoHS
T he iCM answers the audio probl ems for early iCOM transcei ver owners. After
a year of studying the mic preamps and working closely with iCOM America,
Heil Sound i ntroduced their iCM microphone. It i s not the i nexpensive
electrets so common today, but a high performance condenser. It has very
high output to drive the low gain front ends of the early iCOMs and exhibi ts a
wide frequency range. The Heil iCM al so works beautifully with the hi gher
gai n PRO and 7800 series. The iCM si mply makes i COM radios come to life.
T he iCM Microphone contai ns the new Hei l iC, a high performance electret
element, in a beauti ful new pl ati num fini sh body. It i s perfect for hand held
use or mounting on a desk stand or microphone boom. It is suppli ed wi th a
windscreen and universal mic cli p that will interface with a variety of stands
and booms. The iCM comes complete with a self attached 8’ length of the
‘Heilwi re’ cable and terminates in the famil iar 8 pin Foster connector wired to
mate with all early 8 pin iCOM front ends. The frequency range of the new
high performance Hei l i C element i s 35 Hz to 12 kHz. Perfect for the earl y
(pre PRO) as wel l as current production (PRO 1,2,3 and 7800) iCOM ri gs. The
HSTA 706 Adapter may be added to use this mic on iCOM 8 pin modul ar
radios. A 1/4” female pig tail exits this 8 pi n connector that all ows the
i nterface of a foot switch or hand switch to control the PTT l ine. A ‘Soft touch’
PTT swi tch is mounted on the body of the i CM. The iCM with the travel er
HTA PC adapter also makes your computer come to l ife.
1 pc: 3 130 Kč
RoHS
RoHS
PR781 DYNAMIC MICROPHONE
GES07004556
HEIL Professional quality dynamic cardioid m icrophone for elite
class transceivers
CC-1-C ADAPTER CC-1-XLR4 /
COLLINS 3/16"
GES07004670
HEIL Adapter cable Classic, GM, GOLD ELITE, HM-10,
HM-12(4PIN XLR) to Collins (3/16"), 2,5m
CC-1-YM ADAPTER CC-1-XLR4 /
YAESU RJ8 MODULAR
GES08901916
HEIL Adapter cable Classic, GM, GOLD ELITE, HM-10,
HM-12(4PIN XLR) to Yaesu RJ Modular (8PIN), 2,5m
Cable for connecti ng a microphone with a 4PIN XLR connector on
mi crophone side, and a 3/16" microphone connector at TCVR side. Cable
has a PT T female Jack 6,3mm connector for HS-2 hand switch or a FS-3 foot
switch at TCVR side.
1 pc: 1 270 Kč
RoHS
CC-1-D ADAPTER CC-1-XLR4 /
DRAKE 4PIN
GES07004671
HEIL Adapter cable Classic, GM, GOLD ELITE, HM-10,
HM-12(4PIN XLR) to Drake (4 PIN), 2,5m
The amateur radi o divisi on of Heil Sound, Ltd. presents the PR 781, a
professional quality dynamic cardioid microphone for amateur radio that i s
speci fical ly designed for use wi th most makes of Eli te tranceivers of Kenwood,
Yaesu, Ten Tec and i COM. Thi s is a trul y remarkabl e dynamic microphone.
Hei l engi neers were requested by ICOM to develop a very special
mi crophone package for thei r new iC 7800 radi o. They didn't want just a
mi crophone; they wanted a SUPER mi crophone for a super radio. T he Heil
PR 780 was born. The PR 781 is an improvement on the popular PR 780.
The PR 781 is a beautiful performer into j ust about any microphone i nput,
such as TS870, TS950, Pro 1, 2, 3, Yaesu Mark-V, FT 1000MP, FT2000,
FT5000, FT9000, IC7800 etc. Using one of the dynami c elements from the
Hei l broadcast division, the PR 781 offers beautiful wide frequency response
whi le keeping that traditional Heil Sound articul ati on of the speech pattern
something ALL microphones seem to lack and that has been the mainstay of
the Heil Sound line up. Parameters Generating Element: Heil PR Dynamic
Frequency Response: 50 Hz to 16,000 Hz Impedance: Balanced 600 Ohms
Output, 3 pi n Polar Pattern: Cardioid Output Level: -55 dB Diaphragm:
Low-mass alumi num Finish: Black Satin Epoxy Net Wei ght: 14 oz. The PR
781 comes with the SM 1 GES08901460 mount. A CC-1-XLR K Y or i
(K=Kenwood, Y=Yaesu and i=iCOM) i s necessary to order for i nterface with
any transcei ver. Opti onall y you can order the microphone topl ess boom
PL-2T GES08901459 , microphone shock mount SM-2C GES08901655 or
the classic base CB-1-PT T GES08901653 .
1 pc: 5 275 Kč
RoHS
CC-1-XLR-I ADAPTER CC-1-XLR3 /
ICOM 8PIN
Cable for connecti ng a microphone with a 4PIN XLR connector on
mi crophone side, and a 4PIN microphone connector at TCVR side. Cable has
a PT T female Jack 6,3mm connector for HS-2 hand switch or a FS-3 foot
switch at TCVR side.
1 pc: 1 035 Kč
RoHS
CC-1-I ADAPTER CC-1-XLR4 / ICOM
8PIN
GES08901912
HEIL Adapter cable Classic, GM, GOLD ELITE, HM-10,
HM-12(4PIN XLR) to Icom (8PIN) 2,5m
Cable for connecting a microphone with a 4PIN XLR connector on
microphone si de, and a 8PIN flat RJ-Modular Yaesu (FT450, FT817, FT 857,
FT897 etc.) microphone connector at TCVR side. Cable has a PTT female
Jack 6,3mm connector for HS-2 hand swi tch or a FS-3 foot swi tch at T CVR
si de.
1 pc: 1 035 Kč
RoHS
CH-1-I8 ADAPTER XLR4 / ICOM
8PIN
GES08901660
HEIL Adapter Coil Cable for HM Microphone Series with ICOM
8-PIN microphone connector
Cable for connecti ng a microphone with a 4PIN XLR connector on
mi crophone side, and a 8PIN ICOM (IC751, IC775, IC781, IC756PRO etc.)
mi crophone connector at TCVR si de. Cable has a PT T female Jack 6,3mm
connector for HS-2 hand switch or a FS-3 foot switch at TCVR si de.
1 pc: 1 035 Kč
RoHS
CC-1-IM ADAPTER CC-1-XLR4 /
ICOM RJ8 MODULAR
GES07004673
1 pc: 690 Kč
HEIL Adapter cable Classic, GM, GOLD ELITE, HM-10,
HM-12(4PIN XLR) to Icom Modular (RJ 8PIN) 2,5m
Cable for connecti ng a microphone with a 4PIN XLR connector on
mi crophone side, and a 8PIN Modular (IC706 IC7000) mi crophone connector
at TCVR side. Cable has a PTT female Jack 6,3mm connector for HS-2 hand
switch or a FS-3 foot swi tch at T CVR side.
GES08901457
RoHS
CH-1-IM ADAPTER XLR4 / ICOM
MODULAR 8PIN
GES08901661
HEIL Adapter Coil Cable for HM Microphone Series with ICOM
m odular microphone connector
1 pc: 1 035 Kč
RoHS
HEIL Adapter cable Classic-Pro,GM-Pro,Herritage (3PIN XLR) to
Icom (8PIN), 2,5m
CC-1-KM ADAPTER CC-1-XLR4 /
KENWOOD RJ8 MODULAR
GES07004674
HEIL Adapter cable Classic, GM, GOLD ELITE, HM-10,
HM-12(4PIN XLR) to Kenwood Modular (RJ 8PIN) 2,5m
Cable for connecti ng a microphone with a 4PIN XLR connector on
mi crophone side, and a 8PIN Modular microphone connector at T CVR side.
Cable has a PT T female Jack 6,3mm connector for HS-2 hand swi tch or a
FS-3 foot swi tch at T CVR side.
1 pc: 1 035 Kč
RoHS
CC-1-K4 ADAPTER CC-1-XLR4 /
4PIN KENWOOD
Cable for connecti ng balanced Proline microphone to TCVR. Cabl e has a
3PIN XLR connector on microphone side, and a 8PIN ICOM mi crophone
connector at T CVR side. Cable has a PT T female Jack 6,3mm connector for
HS-2 hand switch or a FS-3 foot switch at TCVR si de.
CC-1-XLR-K ADAPTER CC-1-XLR3 /
KENWOOD 8PIN
GES08901455
HEIL Adapter cable Classic-Pro,GM-Pro,Herritage (3PIN XLR) to
Kenwood (8PIN), 2,5m
Cable for connecti ng balanced Proline microphone to TCVR. Cabl e has a
3PIN XLR connector on microphone side, and a 8PIN Kenwood mi crophone
connector at T CVR side. Cable has a PT T female Jack 6,3mm connector for
HS-2 hand switch or a FS-3 foot switch at TCVR si de.
CC-1-POD ADAPTER CC-1-XLR3 /
PC 1/8"
GES07004676
HEIL Adapter cable for m icrophone (3PIN XLR) to PC (1/8" Stereo),
2,5m
Cable for connecting microphone to personal computer.
1 pc: 1 035 Kč
RoHS
CC-1-XLR-Y ADAPTER CC-1-XLR3 /
YAESU 8PIN
GES08901456
1 pc: 1 035 Kč
RoHS
CC-1-K ADAPTER CC-1-XLR4 /
KENWOOD 8PIN
Cable for connecti ng balanced Proline microphone to TCVR. Cabl e has a
3PIN XLR connector on microphone side, and a 8PIN Yaesu mi crophone
connector at T CVR side. Cable has a PT T female Jack 6,3mm connector for
HS-2 hand switch or a FS-3 foot switch at TCVR si de.
1 pc: 1 035 Kč
RoHS
GES07004675
HEIL Adapter cable Classic, GM, GOLD ELITE, HM-10,
HM-12(4PIN XLR) to Kenwood (8PIN) 2,5m
Cable for connecti ng a microphone with a 4PIN XLR connector on
mi crophone side, and a 8PIN Kenwood (TS440, TS570, T S870, TS2000
etc.) mi crophone connector at TCVR si de. Cable has a PTT female Jack
6,3mm connector for HS-2 hand switch or a FS-3 foot switch at TCVR si de.
Cable for connecting balanced Proline microphone (PR 781, Heri tage, T he
Fin, PR 20, PR 30, PR 4, GM-5.1, HM-12, Handi Mi c 4) to T CVR. Cabl e has a
3PIN XLR connector on microphone side, and a 8PIN Yaesu mi crophone
connector at TCVR side. Yaesu FT9000, FT2000, FT 5000, FT-950. Cabl e has
a PTT female Jack 6,3mm connector for HS-2 hand switch or a FS-3 foot
switch at TCVR side.
1 pc: 1 035 Kč
RoHS
CH-1-KM ADAPTER XLR4 /
KENWOOD MODULAR
GES08901663
HEIL Adapter Coil Cable for HM Microphone Series with
KENWOOD modular microphone connector
RoHS
CC-1-T ADAPTER CC-1-XLR4 /
TEN-TEC 4PIN
GES07004672
HEIL Adapter cable Classic, GM, GOLD ELITE, HM-10,
HM-12(4PIN XLR) to Ten-Tec (4 PIN), 2,5m
Cable for connecti ng a microphone with a 4PIN XLR connector on
mi crophone side, and a 4PIN microphone connector at TCVR side. Cable has
a PT T female Jack 6,3mm connector for HS-2 hand switch or a FS-3 foot
switch at TCVR side.
RoHS
CC-1-Y4 ADAPTER CC-1-XLR4 /
YAESU 4PIN
GES08901915
HEIL Adapter cable Classic, GM, GOLD ELITE, HM, HM-12(4PIN
XLR) to Yaesu (4PIN) 2,5m
1 pc: 690 Kč
RoHS
CH-1-YM ADAPTER XLR4 / YAESU
MODULAR 8PIN
GES08901664
HEIL Adapter Coil Cable for HM Microphone Series with YAESU
m odular microphone connector
Cable for connecti ng a microphone with a 4PIN XLR connector on
mi crophone side, and a older 4PIN Yaesu microphone connector at TCVR
side. Cable has a PT T femal e Jack 6,3mm connector for HS-2 hand switch or
a FS-3 foot switch at TCVR si de.
RoHS
CC-1-Y ADAPTER CC-1-XLR4 /
YAESU 8PIN
Cable for connecti ng a microphone with a 4PIN XLR connector on
mi crophone side, and a 8PIN Yaesu (FT847, FT920, FT950, FT990, FT1000,
FT2000, FT5000, FT9000 etc.) mi crophone connector at T CVR side. Cable
has a PT T female Jack 6,3mm connector for HS-2 hand switch or a FS-3 foot
switch at TCVR side.
1 pc: 1 035 Kč
RoHS
1 pc: 1 035 Kč
GES08901914
HEIL Adapter cable Classic, GM, GOLD ELITE, HM-10,
HM-12(4PIN XLR) to Yaes u (8PIN), 2,5m
GES08901462
HEIL XLR 3PIN male to XLR 3PIN female Balanced Connector
Cable, 2.5m
RoHS
1 pc: 1 035 Kč
1 pc: 690 Kč
RoHS
1 pc: 1 035 Kč
HEIL Adapter cable for m icrophone (3PIN XLR) to Yaesu
ballanced, 2,5m
CC-1-XLR-3 Mikrofonní kabel
CC-1-XLR3 / XLR3
GES08901913
1 pc: 1 035 Kč
HEIL Adapter cable Classic-Pro,GM-Pro,Herritage (3PIN XLR) to
Yaesu (8PIN), 2,5m
CC-1-XLR-YB ADAPTER CC-1-XLR3
/ YAESU BALLANCED
HEIL Adapter Coil Cable for HM Microphone Series with
KENWOOD 8-PIN m icrophone connector
Cable for connecti ng a microphone with a 4PIN XLR connector on
mi crophone side, and a 4PIN Kenwood (TS440, TS570, T S870, TS2000
etc.) mi crophone connector at TCVR si de. Cable has a PTT female Jack
6,3mm connector for HS-2 hand switch or a FS-3 foot switch at TCVR si de.
1 pc: 1 035 Kč
RoHS
GES08901662
HEIL Adapter cable Classic, GM, GOLD ELITE, HM-10,
HM-12(4PIN XLR) to Kenwood (4PIN), 2,5m
1 pc: 1 035 Kč
RoHS
GES07004669
1 pc: 690 Kč
RoHS
CH-1-K8 ADAPTER XLR4 /
KENWOOD 8PIN
1 pc: 690 Kč
RoHS
FL-2 FLANGE MOUNT
GES08901652
HEIL Flange Mount with Brass Insert and thumb s crew
HEIL SOUND - Microphones for
broadcasting
FIN Blue
GES08902036
HEIL The Fin traditional dynam ic microphone for live sound,
recording and broadcast with Blue LED
HEIL SOUND - Microphone
Management Hardware
HB-1 MICROPHONE ALL STEEL
BOOM
GES07004645
HEIL quiet, freely moving, balanced, articulated, all s teel mic boom
1 pc: 740 Kč
RoHS
CB-1-PTT HEIL CLASSIC BASE
Hei l Sound is pleased to introduce The Fin, exhibi ting a remarkabl e, natural,
cl ear sound and designed especially for l ive sound, recording and broadcast
appli cations. The exceptional performance i s achi eved by the use of a
speci al magnet structure with a large 1 1/8” alumi num l ow mass voice coil
assembly si mi lar to the Heil PR 20. The frequency response is 50 Hz - 18 kHz
with that traditional Heil Sound mi d range ‘bouquet’ at 4 kHz, which presents
incredi ble brilli ance and presence. The Fin exhi bits a ti ght linear cardioid
pattern. The chrome fini sh i s a special ‘showchrome’ where the steel body i s
copper plated and then double chrome plated producing a deep chrome
finish. A blue molded internal foam wi ndscreen i nside the grill covers the Heil
dynamic microphone el ement mounted in a speci all y tooled rubber shock
mount. The fun part of the new Heil The Fin is the four blue L.E.D. lamps
mounted i nside. These can onl y be illuminated when using the FIN into one
of the 3 pi n balanced XLR inputs of a professional mixing console that
suppli es a + 48 volt d.c. phantom vol tage down the balanced mi c line.
Standard 5/8” – 27 mi crophone stand threads allow the The Fi n to be
mounted on booms or floor stands. The microphone audio will also work into
an unbalanced l ow impedance input used on amateur radios,
communi cations audi o or simpl e publi c announcement systems. None of
these wi ll have the proper voltage to il luminate the lamps but the
mi crophone wi ll work perfectly. Shoul d you want to illuminate the lamps
when used for amateur radio, etc. T he FIN can be used into one of the
balanced inputs of a small Behri nger UB 802 (or similar) mixer or the 3 pin
XLR bal anced of a W2IHY 8 band equal izer, with their phantom power
activated. The FIN is terrifi c for vocal s, instrument amplifiers, harmonica, and
speech, and puts the FUN back into the dynamic microphone. For amateur
radio use, a CC-1 XLR is needed to interface with your transceiver.
To answer the many requests for an economy mi crophone boom, Heil Sound
presents the Hei l HB-1. The HB-1 i s an articul ated arm which is of very
substantial steel channel structure and balanced by four external springs.
Capable of supporting microphones up to 2.5 lbs. The HB-1 is shipped with a
brass l ined 'C' cl amp mount that accept up to a 1.5" thick table. The HB-1 will
fit al l of the brass l ined Heil mounti ng accessori es: * DT-1 Flush Mount that
mounts through a 1.5" hole in the desk top * FL-2 Flange Mount secures to
any flat surface * WM-1 Wall Mount * RS-1 12" Riser Mount The HB-1 Boom
accepts al l of the standard 5/8" -27 threaded microphone hardware. T he
threaded chrome stem can be secured into it's needed position by tighteni ng
the thumb screw.
GES08901653
HEIL Classic Base with PTT switch
1 pc: 1 855 Kč
RoHS
PL2T MICROPHONE TOPLESS
BOOM
GES08901459
1 pc: 2 070 Kč
HEIL Microphone Topless Boom with Brass inserts in supplied C
Clamp
RoHS
SM-1 MICROPHONE SHOCK
MOUNT
GES08901460
HEIL 1" Mic Shock Mount for 1" mics GM, iCM, HM, PR20, PR781
1 pc: 5 830 Kč
RoHS
PR20 COMMERCIAL PROLINE
DYNAMIC MICROPHONE
GES08901650
HEIL Proline Cardioid Dynamic Voice and Instrument Microphone
Suppl ied Accessori es is C CLAMP 1,5" desk mount. On opti onal order i s DT-1
desk Toop flush mount, FL-2 Flange Mount, RS-1 Riser and WM-1 Wall
Mount.
1 pc: 3 180 Kč
RoHS
SB-2 MICROPHONE BOOM
The PR20 has been desi gned for commercial recordning and live sound
rei nforcement applications. Use a speci al magnet structure and a large
alumini um 1-1/8" low mass voice coi l assembly. Frequency range i s 50Hz to
18kHz. Is usable in extrem hi gh sound pressure levels and is immune to
overload condi tions maging perfect for vocals. Thi s i s one great l ive vocal
mi crophone that has finally replaced the "ball mic" of the 1970s. Hei l PR20
come in a leatherette carryi ng bag wi th mic clip, one gold+one black+one
silver microphone screen and acousti cal foam windcsreen. For amateur radio
a CC-1 XLR3 cable i s needed to interface with your TCVR. PR-20 has a XLR3
male connector. Impedance is 600 Ohms ballanced.
GES08901451
HEIL Small Boom Extendeable to 20", with Nylon Stern
1 pc: 2 120 Kč
RoHS
PRSMC MICROPHONE SHOCK
MOUNT
GES08901655
HEIL 2" Mic Shock Mount in champagne for PR40
1 pc: 4 110 Kč
RoHS
PR30 DYNAMIC PROLINE STUDIO
MICROPHONE
GES08901649
HEIL Proline Large Diameter Dynam ic Studio Microphone
Suppl ied Accessories is C CLAMP mount.
1 pc: 1 680 Kč
RoHS
DT-1 DESK MOUNT FLUSH
1 pc: 2 785 Kč
RoHS
GES08901469
HEIL Desk Top Mount Flush with Brass Insert
Headphones
SE-90
RoHS
PR40 PROLINE BROADCAST
STUDIO MICRPHONE
GES07004643
STEREO headphones 10-20000Hz, 2x16Ohm ., 2x0,05W, Jack
3,5mm , weight 8g
1 pc: 6 685 Kč
GES08901453
HEIL Proline Broadcast and Recording Studio Microphone
1 pc: 930 Kč
RoHS
WM-1 WALL MOUNT
GES08901470
HEIL Wall Mount with Bras s Insert for PL2T or SB2
1 pc: 585 Kč
RoHS
RS-1 RISER
GES08901468
HEIL Riser 12" (30,5cm)
1 pc: 740 Kč
1 pc: 8 870 Kč
RoHS
RoHS
1 pc: 319.00 Kč
RoHS
RoHS
These in-ear headphones CRONO
E-12B
GES07004694
STEREO headphones 20-20000Hz, 2x16Ohm., Jack 3,5m m,
weight 14g
SE-62
GES07004641
STEREO headphones 10-20000Hz, 2x16Ohm., 2x0,05W, Jack
3,5m m, weight 4g
MD-302
GES07004682
STEREO headphones 20-20000Hz, 2x32Ohm ., 2x0,05W, Jack
3,5mm , weight 50g
1 pc: 189.00 Kč
RoHS
RoHS
These in-ear headphones CRONO
E-11W
1 pc: 139.00 Kč
RoHS
RoHS
These in-ear headphones CRONO
E-13B
GES07004693
1 pc: 270.00 Kč
STEREO headphones 20-20000Hz, 2x32Ohm., Jack 3,5m m,
weight 14g
GES07004719
RoHS
RoHS
MD-306
GES07004683
STEREO headphones 20-20000Hz, 2x32Ohm ., 2x0,05W, Jack
3,5mm , weight 50g
STEREO headphones 20-20000Hz, 2x16Ohm., Jack 3,5m m,
weight 14g
1 pc: 90.00 Kč
RoHS
RoHS
1 pc: 109.00 Kč
RoHS
RoHS
These in-ear headphones CRONO
E-14R
GES07004720
SE-50
GES07004473
STEREO headphones 20-20000Hz, 2x32Ohm., 2x0,06W, Jack
3,5m m, weight 17g
STEREO headphones 20-20000Hz, 2x16Ohm., Jack 3,5m m,
weight 14g
MFJ-392B Lightweight Radio
Communication and SWL
Headphones
GES08900687
Radio Com munication and SWL Headphones 16 Ohm / 450mW /
100Hz-24kHz; Volume control; 3.5mm Jack
1 pc: 45.00 Kč
RoHS
RoHS
SE-20
GES07004474
STEREO headphones 20-20000Hz, 2x32Ohm., 2x0,02W, Jack
3,5m m, weight 12g
1 pc: 149.00 Kč
RoHS
RoHS
These in-ear headphones CRONO
E-14M
1 pc: 270.00 Kč
RoHS
RoHS
GES07004721
Impedance 16 Ohms / 1kHz, sensi tivity 102 dB/mW. Weight 230 gram (8
ounces) only MFJ-392B i s perfect for amateur radio and shortwave li stening.
Great for all modes -- SSB, FM, AM, data, and CW. Each earphone has an
i ndividual vol ume control. Superb padded headband and ear cushioned
desi gn makes li stening extremely comfortabl e. Youl l forget theyre even there
as you listen to stations all over the world! Hi gh-performance driver unit
reproduces enhanced communi cation sound. Si gnals never sounded so
crystal clear! MFJ-392B will bring out speech fideli ty you never knew existed.
Has free 1/4 inch phono adapter. Near zero loss on si gnal transmission from
the gold pl ated plug and cord. Super l ightweight earphones (8 ounces) come
with 9 feet of cord -- l ets you easi ly move about and still listen to your radi o.
MFJ-392B handl es 450 mW and has a frequency response of 100-24,000 Hz.
Impedance is 16 Ohms at 1 KHz, sensi tivity is 102dB/mW. Works in mono or
stereo mode. T he MFJ-392B also comes with MFJs No Matter What Warranty.
1 pc: 595 Kč
RoHS
STEREO headphones 20-20000Hz, 2x16Ohm., Jack 3,5m m,
weight 14g
EP-302
GES07004681
Set of foam cushions for earphones, 4pcs
1 pc: 39.00 Kč
RoHS
MD-39
GES07004433
STEREO headphones 20-20000Hz, 2x32Ohm., 2x0,1W, Jack
3,5m m, weight 28g
1 set: 45.00 Kč
RoHS
RoHS
1 pc: 149.00 Kč
EP-4
RoHS
RoHS
SE-80
GES07004642
GES07004483
Set of small foam cus hions for earphones
STEREO headphones 20-20000Hz, 2x32Ohm., 2x0,015W, Jack
3,5m m, weight 2g
1 pc: 99.00 Kč
RoHS
RoHS
1 pc: 195.00 Kč
RoHS
RoHS
1 pc: 59.00 Kč
RoHS
RoHS
EP-6/SW
GES07004679
Set of miniature foam cushions for earphones
HM-54W
GES07004692
Stereoheadphones 20-20000Hz, 2x32Ohm., with m icrophone
2,2kOhm, 144g
HEIL SOUND - Headsets for Amateur
Radio
PS-3 PROSET 3 - Professional
Headphone
GES07004689
HEIL SOUND professional headphone with exceptional
articulation and clarity
Consisti ng of 3 pairs (black) for earphones.
1 pc: 49.00 Kč
RoHS
RoHS
Headsets
HM-15B
1 pc: 339.00 Kč
GES07004702
Stereoheadphones with volume control 18-22000Hz, 2x32Ohm.,
with m icrophone 2,2kOhm ,
RoHS
RoHS
BH-005
1 pc: 89.00 Kč
RoHS
RoHS
HM-52B
GES07004690
Stereoheadphones 18-22000Hz, 2x32Ohm., with m icrophone
2,2kOhm, 125g
GES07004478
Stereoheadphones 20-20000Hz, 2x32Ohm., 50mW, m ic. electret
50-12500Hz, 24
1 pc: 769 Kč
RoHS
RoHS
BH-004
GES07000050
Stereoheadphones 20-20000Hz, 2x32Ohm., 100m W, mic.
50-12000Hz, 150g
A professional headphone with exceptional articul ati on and clarity, beautiful
soni c accuracy in a closed back, li ghtweight headset for moni toring in
recording and broadcast studi os, podcasti ng and computer outputs. The
Basics accuracy in a closed back, lightweight headset for monitori ng in
recording and broadcast studios, amateur radi o stati ons, podcasti ng and
computer outputs. The HEIL Pro Set 3 features high quality 40 mm
neodymium magnets and voice coil s, li ghtweight, ergonomically designed
cushioned headband adjustable for maxi mum comfort while si gnificantl y
reducing outside noise. Suppli ed with three detachable cabl es. 1.8 M fl exible
strai ght cable. 1.8 M straight cord with mating iPhone/iPod compatible
3.5mm pl ug. 3 M coil cord - all twist lock terminating in a 1/8" (3.5 mm)
professi onal gold pl ated screw-on 1/4" (6.3mm) adapter. HEIL PRO SET 3
Features: 10 Hz. – 22 kHz extended frequency response for exceptional cl ear,
bal anced sound reproduction Convenient fol ding constructi on for compact
transport and storage Ergonomic design with soft, adjustable cushioned
headband. Serious acousti cal outside noise reduction Mid si ze desi gn wi th
i nternal steel headband Soft padded, replaceable ear cushions T hree twist
l ock detachable cables Gol d-plated stereo and screw-on 1/4" adapter Driver
Diameter: 40 mm Rare Earth Neodymi um magnets Alumi num Inlay Ear Cup
Sensitivity: 102 dB Extended Frequency Response: 10 Hz-22 kHz Maximum
Input Power: 1,000 mW at 1 kHz Impedance: 32 ohms
1 pc: 2 915 Kč
RoHS
PSE6 PROSET ELITE Elite Headset
with Microphone Element HC6
GES07004553
HEIL SOUND Elite Class Head Set with verry high degree of
outside noise rejection.
1 pc: 119.00 Kč
RoHS
RoHS
HM-53B
GES07004691
Stereoheadphones 20-20000Hz, 2x32Ohm., with m icrophone
2,2kOhm, 168g
1 pc: 189.00 Kč
RoHS
RoHS
BH-003
GES07004477
Stereoheadphones 20-20000Hz, 2x32Ohm., 30mW, m ic. electret
50-12500Hz, 170g
1 pc: 848 Kč
RoHS
RoHS
Heil Sound is pleased to introduce the exci ting new Pro Set Eli te hi gh-end
boomset for the Amateur and Broadcast industries! T he Pro Set Eli te offers
highly effi ci ent speakers mounted in acousticall y-tuned enclosures, to provide
a very high egree of (passi ve) outside noise rejection. The Pro Set Eli te
i ncludes Heil Sound's exclusi ve Phase Reversal system, which all ows the
operator to put the incoming si gnals in and out of phase between the left and
right ears, yieldi ng on-the-fly creati on of spatial separation of si gnals in
dynami c pil e-up situati ons on today's crowded bands. T he Pro Set Elite's
headphones fold up for easy transportation and storage, and the Pro Set Eli te
i s unbelievabl y l ight i n weight and comfortable. . .ideal for long operating
sessions. The Pro Set Elite's ear cushions are fi eld-repl aceabl e, and they
come with washabl e cotton covers. T he Pro Set Eli te incl udes a six-foot
coiled cabl e, which terminates in two plugs: one is a 1/8" (3.5 mm) stereo,
which i s the headphone plug (a 1" adapter i s supplied). The other plug is a
1/8" mono plug, which carries the mi crophone signal. T herefore, the Pro Set
Elite wi ll interface to the current AD-1 microphone adapter HEIL cabl es, as
used with the Pro Set, BM-10, etc. The Pro Set El ite, in addi tion to being
spectacular for Amateur Radi o use, also is outstanding for commerci al
broadcast and podcast use. Incl udes Hei l Sound new HC6 dynami c el ement.
T he Pro Set Elite 6 includes Heil Sound's new HC-6 dynami c el ement. The
HC-6 is a full-range element, with the -3 dB points at 100 Hz on the low side
and 12.5 kHz on the high side, but addi tionally with a ri se of +6 dB in the
2000-3000 Hz range to enhance articulation on SSB circui ts (or duri ng noi sy
sportscasti ng appli cations). The HC-6 element sounds beauti ful on i ts own,
but it also l ends itself to the "equalization" features found on many modern
DSP-based transceivers. An excellent demonstration of the capabilities of the
new HC-6 el ement, found on the new Pro Set El ite, is now up on our Web
si te. Here i s the link: www.heilsound.com/amateur/press/hc6.mp3 This bri ef
demonstrati on fi le shows the effect of simpl e DSP mi c equalizer adjustments,
performed i n the transceiver's menu, all owi ng the HC-6 el ement to behave as
a broadcast-qual ity mi crophone, an SSB all-around microphone, or a pil e-up
busting DX microphone.
1 pc: 4 850 Kč
RoHS
1 pc: 339.00 Kč
RoHS
RoHS
PSEiC PROSET ELITE Elite Headset
with Mic Element iC for ICOM
GES07004554
HEIL SOUND Elite Class Head Set PSEiC for Icom with verry high
degree of outside noise rejection.
Hei l Sound i s pleased to introduce the exciting new Pro Set El ite high-end
boomset for the Amateur and Broadcast industri es! T he Pro Set El ite iC offers
highl y efficient speakers mounted i n acoustical ly-tuned enclosures, to provi de
a very high egree of (passive) outsi de noise rej ection. The Pro Set Elite iC
includes Hei l Sound's exclusive Phase Reversal system, which al lows the
operator to put the incoming signal s in and out of phase between the l eft and
right ears, yielding on-the-fly creation of spati al separation of signal s in
dynamic pi le-up situations on today's crowded bands. The Pro Set Elite's
headphones fol d up for easy transportation and storage, and the Pro Set El ite
is unbelievably light in weight and comfortabl e. . .ideal for long operati ng
sessions. The Pro Set Eli te's ear cushi ons are fiel d-replaceable, and they
come with washable cotton covers. The Pro Set El ite includes a six-foot
coiled cable, which termi nates in two plugs: one is a 1/8" (3.5 mm) stereo,
whi ch is the headphone pl ug (a 1" adapter is suppli ed). The other plug is a
1/8" mono plug, which carries the microphone signal . T he Pro Set Elite, in
addition to being spectacular for Amateur Radio use, al so is outstandi ng for
commercial broadcast and podcast use. Includes Heil Sound iC electret
element. The Pro Set El ite iC utilizes Heil Sound's exclusive "i C" electret
condenser el ement, with the higher output that is so important on many
(mostl y earl ier) Icom transceivers. T he -3dB points on the "i C" el ement are at
80 Hz and 12.5 kHz, and the "i C" el ement does not have the pronounced rise
above 2000 Hz. The "i C" element requi res +5 Volts of DC to power the
condenser element. T he Pro Set Elite iC incl udes the AD-1-I8 adapter cable
for the Icom radi os with 8-pin round microphone jacks. An excellent
demonstration of the capabi liti es of the new HC-6 el ement, found on the new
Pro Set Eli te, is now up on our Web site. Here is the l ink:
www.heilsound.com/amateur/press/hc6.mp3 Thi s brief demonstration file
shows the effect of simple DSP mic equalizer adj ustments, performed in the
transcei ver's menu, al lowing the HC-6 element to behave as a broadcastquali ty mi crophone, an SSB all-around microphone, or a pile-up busting DX
mi crophone.
1 pc: 5 140 Kč
RoHS
PS-6 PROSET 6 - Headset with
Microphone Element HC6
GES07004653
HEIL SOUND Highest Class Headset. With HC-6 Microphone
Element
PSMP Award-winning
communications headset designed
for use with your personal computer
GES07004655
BAG-2
GES08901491
Special leatherette carrying bag for HEIL Quiet Phone, BM and
Traveler
The Pro Set Media Pro is an award-winning communications
headset designed for use with your PC
Based on Heil Sound's popular Pro Set communicati ons headset, the Pro Set
Medi a Pro utili zes a high-level condenser microphone element desi gned
speci fical ly for the requi rements of computer sound card inputs. T he result i s
beautiful, broadcast-quality audio, with plug-and-play functi onali ty. The Pro
Set Medi a Pro earphones are acoustically tuned, and they i ncorporate Heil
Sound's exclusi ve phase reversal feature that creates a spati al widening effect
that often makes incoming audio easier to understand. The Heil Sound Pro
Set Media Pro is terminated in two industry-standard 1/8" male pl ugs: the
Red pl ug connects to the "Mi crophone" input jack on your sound card, while
the Black pl ug connects to the sound card's audio output ("Headphone" or
"Speaker" jack). T he Medi a Pro comes to you with removable cotton ear pad
covers that can be washed. T he comfortable vinyl ear pads they cover can
also be removed, shoul d they even need to be replaced. A foam wi nd screen
is fitted over the microphone, and it also can easi ly be removed and/or
replaced. For outstanding audio on your computer-based communicati ons
appli cations, choose the Heil Sound Pro Set Media Pro!
1 pc: 585 Kč
RoHS
HEIL SOUND - Adapter Cables
AD-1-C ADAPTER HEIL SOUND for
COLLINS
GES08901494
Microphone adapter HEIL SOUND for COLLINS
1 pc: 3 235 Kč
RoHS
PS-EPC SPARE COTTON EAR
COVERS PROSET
GES08901658
HEIL Cotton Ear Covers (booties) for PROSET and PROSET PLUS
ear pads
1 pc: 770 Kč
RoHS
AD-1-D ADAPTER for DRAKE
GES08901495
Microphone adapter HEIL SOUND for DRAKE
1 pair: 195.00 Kč
RoHS
EP-BM-BLACK
GES08901733
HEIL Ear Pad 2" (51m m) for BM5, BM10. Black, Pair
1 pc: 609 Kč
RoHS
AD-1-I8 ADAPTER HEIL SOUND for
ICOM 8PIN
GES08901496
Microphone adapter HEIL SOUND for ICOM with 8PIN round MIC
connector
The Pro Set 6 utilizes the new ful l-range HC-6 mic element, so popular on
the high-end Pro Set El ite 6. The HC-6 brings basi cally the same
highfrequency response as was found on the Pro Set 5's HC-5 mic element,
but wi th a wider response on the bass side (down to about 150 Hz). Thi s
provides greater fi delity for local operations, and modern DSP-based ham rigs
have transmitter adj ustments that can easily allow thi s bass response to be
rol led off, if desired. The Pro Series Boomsets are designed to meet the hi gh
standards of the most critical Contester and DX Chasers. Rugged but
lightweight headset reduces listening fatigue, reduces noi se and enhance
intell igi bil ity. Headset has special microphone element HC-6. Added a
speaker Phase Reversal switch alows to change the sound fiel d between the
two high quality speakers. "In Phase", the signal i s centered in your head so
you can "see" it better. "Out of Phase", the si gnals are spatially widened so
they are easier to pick out of a pil eup up. Use an AD-1 Series HEIL Adapter
(not included) depending on your T CVR type. T herefore, the PS-6 will
interface to the current AD-1 microphone adapter HEIL cabl es, as used with
the other Pro Set.
1 pair: 159.00 Kč
RoHS
EP-BM-BLUE
GES08901477
HEIL SOUND Highest Class Headset. With iC Mike Element. For
ICOM only.
1 pc: 609 Kč
RoHS
AD-1-iCM ADAPTER HEIL SOUND
for ICOM MODULAR
GES08901497
Microphone adapter HEIL SOUND for ICOM with MODULAR MIC
connector
1 pc: 4 190 Kč
RoHS
PS-iC PROSET ICOM - Headset with
iC Microphone Element for ICOM
GES08901734
HEIL Ear Pad 2" (51m m) for BM5, BM10. Blue, Pair
Adapter for ICOM IC730, IC735, IC745, IC751, IC761, IC765, IC720, IC725,
IC726, IC756PRO, IC728, IC781, IC901, IC910, IC3200, IC7700, IC7800 etc.
with 8PIN round microphone connector. Pi n 1: Mi crophone In* Pi n 5: PTT
Pin 6: PT T Ground Pi n 7: Microphone Ground *Pin 1 also carri es vol tage for
the electret el ements used in Icom mics. T his voltage must be blocked for use
of Heil Sound dynami c elements.
1 pair: 159.00 Kč
RoHS
EP-BM-RED
GES08901735
HEIL Ear Pad 2" (51m m) for BM5, BM10. Red, Pair
Adapter for ICOM IC703, IC706, IC2000, IC7000 etc. Pin 4: PT T Pin 5:
Microphone Ground Pi n 6: Microphone In* Pin 7: Ground *Pin 6 al so carries
voltage for the electret elements used in Icom mics. This vol tage must be
blocked for use of Heil Sound dynamic elements.
1 pc: 609 Kč
RoHS
AD-1-K4 ADAPTER HEIL SOUND for
KENWOOD 4PIN
GES08901499
Microphone adapter HEIL SOUND for KENWOOD with 4PIN MIC
connector.
1 pair: 159.00 Kč
Adapter for KENWOOD TS120, TS130, T S520, TS530, TS700, TS820,
T S830, TR2200, TR7200, TR7400, TR7500 etc. wi th round 4 PIN
microphone connector. Good also for older Elecraft K3 with 4PIN round
connector.. Pi n 1: Microphone In Pin 2: PTT Pin 3: PT T Ground Pi n 4:
Ground
RoHS
BAG-1
1 pc: 609 Kč
GES08901490
Special leatherette carrying bag for HEIL headsets PROSET and
PROSET PLUS
RoHS
AD-1-K8 ADAPTER HEIL SOUND for
KENWOOD, ELECRAFT 8PIN
GES08901500
Microphone adapter HEIL SOUND for KENWOOD and ELECRAFT
with 8PIN round MIC connector
Adapter for KENWOOD T S 450, TS 570, T S 870, TS 940, T S 950, TS 2000
etc. and for ELECRAFT K2 and ELECRAFT K3 with 8PIN round connector.
Pin 1: Mi c Pin 2: PTT Pin 7: Microphone Ground Pin 8: PT T Ground
1 pc: 609 Kč
The Pro Seri es Boomsets are desi gned to meet the high standards of the
most critical Multi-Op Contester and DX Chasers. T he Pro Set iC (PS iC)
uti lizes the Heil Sound "iC" condenser element specially designed by Heil
Sound for compatibility with the low gain found on many Icom transcei vers'
mi c amp stages. The PS iC is also shipped with the AD-1 iC adapter cable
(the PS 4 requi res an optional adapter cabl e so as to match the Pro Set to
your transceiver's mic jack requirements). PROSET ICOM is international ly
approved product of extra class. Rugged but l ightweight headset reduces
listeni ng fati gue, reduces noise and enhance intell igi bil ity. Headset has
speci al ful l range ICOM microphone element. Added a speaker Phase
Reversal switch alows to change the sound field between the two high quali ty
speakers. "In Phase", the signal is centered i n your head so you can "see" it
better. "Out of Phase", the si gnals are spatial ly widened so they are easier to
pick out of a pil eup up. The AD-1 Series HEIL Adapter for ICOM radio i s
included.
1 pc: 4 150 Kč
RoHS
PSP windscreen, spare part
GES07004704
HEIL SOUND Winds creen for PSP headset, spare part.
1 pc: 238.00 Kč
RoHS
AD-1-KM ADAPTER HEIL SOUND
for KENWOOD MODULAR
GES08901501
Microphone adapter HEIL SOUND for KENWOOD with MODULAR
8PIN MIC connector
1 pc: 745 Kč
Adapter for KENWOOD TS480, VHF/UHF Mobil es TM-V7, 707, 461 etc. Pin
3: Ground Pin 4: PT T Pi n 5: Microphone Ground Pi n 6: Microphone In
RoHS
1 pc: 609 Kč
RoHS
AD-1-T4 ADAPTER HEIL SOUND for
TENTEC 4PIN
GES08901502
Microphone adapter HEIL SOUND for TEN-TEC with 4PIN MIC
connector
Adapter for TEN-TEC (Orion)
1 pc: 609 Kč
RoHS
AD-1-Y4 ADAPTER HEIL SOUND for
YAESU 4PIN
MFJ-1128 MULTIPLE OUTLET
GES08901503
Microphone adapter HEIL SOUND for YAESU with round 4PIN MIC
connector
4-pin Round (FT 7, FT 101, FT 101Z, FT201, FT221, FT 223, FT 225R,
FT227R, FT301, FT901, FT902 etc.) Pi n 1: Ground Pin 2: Microphone In Pin
3: PTT Pin 4: No Connection (*Ground on FT-221R)
GES08900346
De Luxe High Current DC Multiple-Outlet 12-24VDC,
12outl.,40Amax.,V-Meter 0-25V
Traffic, Station, Contests
1 pc: 609 Kč
RoHS
AD-1-Y8 ADAPTER HEIL SOUND for
YAESU 8PIN
GES08901625
Microphone adapter HEIL SOUND for YAESU with 8PIN round MIC
connector
Adapter for YAESU wi th 8-pi n Round (FT650, FT736, FT747, FT 757, FT767,
FT840, FT847, FT 920, FT 990, FT1000, MARK-V, FT2000, FT5000, FT 9000
etc.) Pin 6: PT T Pi n 7: Ground Pin 8: Microphone In
1 pc: 2 780 Kč
Contest Voice Keyer
MFJ-434B VOICE KEYER
RoHS
GES08900723
Contest and DX Voice Keyer; 5 memories/75sec.; 165 x 64 x
165m m
MFJ-1129 MULTIPLE OUTLET
GES08900347
De Luxe High Current DC Multiple-Outlet 12-24VDC,
10outl.,40Amax.,V-Meter 0-25V
1 pc: 609 Kč
RoHS
AD-1-YM ADAPTER HEIL SOUND
for YAESU MODULAR 8PIN
GES08901504
Microphone adapter HEIL SOUND for YAESU with 8PIN MODULAR
MIC connector
Adapter for YAESU with 8PIN modular microphone connector (FT450, FT817,
FT857, FT897 etc.) Pin 2: Ground Pin 3: PTT Pin 4: Mi crophone In Pin 5:
Mi crophone Ground
1 pc: 609 Kč
RoHS
HSTA-IM ADAPTER ICOM
MODULAR
1 pc: 3 040 Kč
RoHS
Mi croprocessor control led Contest Voice Keyer. 5 memories up to 75 seconds.
Repeat del ay 0,5 to 500 seconds. Transparent to Your microphone. Use 8-pin
modular or 8-pin round microphone plug. Internal jumpers let You customize
MFJ-434B to Ali nco, Icom, Kennwood, Radi o Shack or Yaesu. Use 9 Volt
battery or 9-15VDC wall charger (MW 96 - GES 075 000 52 from
GES-ELECTRONICS).
GES08901723
1 pc: 5 290 Kč
RoHS
Manual Switches for RF
HEIL Adapter for ICOM IC703, IC706, IC208H, IC220H, IC2100,
IC2720, V8000
Adapter for headset HTSS or HT DS and transceiver (Modul ar conector).
MFJ-1703 ANTENNA SWITCH
DC Multi Outlets
GES08901728
HEIL Adapter for ICOM IC735, IC746, IC756, IC756PROII,
IC756PROIII, IC7800
MFJ-1112 MULTIPLE OUTLET
GES08900443
Antenna / Transmitter Crossover Switch
1 pc: 690 Kč
RoHS
HSTA-I8 ADAPTER ICOM 8PIN
Switches, PTT
GES08900340
DC Multiple Outlet (6 pairs of RF bypassed binding posts)
Adapter for headset HTSS or HT DS and transceiver (8PIN).
1 pc: 690 Kč
RoHS
HSTA-K8 ADAPTER KENWOOD
8PIN
GES08901729
HEIL Adapter for KENWOOD with 8PIN conector
Adapter for headset HTSS or HT DS and transceiver.
1 pc: 690 Kč
RoHS
HSTA-KM ADAPTER KENWOOD
MODULAR
GES08901730
1 pc: 795 Kč
RoHS
HEIL Adapter for KENWOOD TS480, G707A, V7, V700A
Adapter for headset HTSS or HT DS and transceiver (Modul ar conector).
1 pc: 690 Kč
RoHS
HSTA-YM ADAPTER YAESU
MODULAR
GES08901721
1 pc: 1 190 Kč
RoHS
VEC-316
GES08901547
MFJ-1702 ANTENNA SWITCH
GES08901147
Antenna switch 1IN / 2OUT; 1kWCW; <0,2dB; 0÷450MHz; UHF-fem;
center ground
Deluxe DC Multiple Outlet up to 15A. Voltmeter 0-25VDC. "ON"
LED.
HEIL Adapter for YAESU with 8PIN MODULAR connector for FT817,
FT857, FT897
Adapter for headset HTSS or HT DS and transceiver.
1 pc: 690 Kč
RoHS
ADMY-817 ADAPTER YAESU
GES08901505
HEIL Mic Adapter 8PIN-male CC-1 type to 8PIN YAESU (FT817,
FT857, FT897)
1 pc: 530 Kč
RoHS
1 pc: 1 590 Kč
RoHS
MFJ-1117 MULTIPLE OUTLET
GES08900342
High Current DC Multiple Outlet (2x 4 pos ts). 12-24VDC, 35A max.
MFJ-1702C ANTENNA SWITCH
GES08901148
Antenna switch 1IN / 2OUT; 1kWCW; <0,2dB; 0÷450MHz;
UHF-female; center ground; lightning protection
1 pc: 1 060 Kč
RoHS
MFJ-1702CN ANTENNA SWITCH
GES08901149
Antenna switch 1IN / 2OUT; 1kWCW; <0,2dB; 0÷450MHz; N-female;
center ground; lightning protection
1 pc: 770 Kč
RoHS
1 pc: 1 720 Kč
RoHS
DC-35
GES08901546
Deluxe High Current DC Multiple-Outlet 12-24VDC. 2x(6+2) pos ts,
Meter
1 pc: 1 190 Kč
RoHS
1 pc: 2 250 Kč
RoHS
MFJ-1704 ANTENNA SWITCH
GES08900444
Ant.switch 1IN / 4OUT; 1kWCW; <0,2dB; 0÷450MHz; UHF-fem ale;
center grnd; lightning protection
Remote Switches, for RF
Manual Switches, PTT
RCS-10X REMOTE COAX SWITCH
GES08901150
Remote Coax Switch, 8-pos ition, 1.8 - 150 MHz; 5kW < 30MHz,
2,5kW / 50MHz
HS-2 Ergonomic push to talk hand
PTT switch
GES08901507
HEIL "Magnum" Ergonomic Handswitch
1 pc: 2 120 Kč
RoHS
MFJ-1704N ANTENNA SWITCH
GES08900445
Antenna switch 1IN / 4OUT; 1kWCW; <0,2dB; 0÷450MHz; N-fem ale;
center ground; lightning protection
1 pc: 2 250 Kč
RoHS
MFJ-1701 ANTENNA SWITCH
GES08901146
Antenna switch 1IN / 6OUT; 1kW CW; 1.8-30MHz; UHF-female;
50-75Ohm; unused inputs grounded
1 pc: 2 120 Kč
RoHS
MFJ-1700C ANTENNA SWITCH
GES08901145
Antenna switch 1-6IN/1-6OUT; 1kW CW; 1.8-30MHz; UHF-fem;
50-75 Ohm; unus ed input grounded
The RCS-10 i s a versatile antenna switch desi gned for 50-ohm systems. It
handles high power, and sealed relays offer excellent life and connecti on
rel iabili ty. It requi res onl y three small i solated control wires, pl us a ground
return that can even can be the coaxial cable shield. The relay box can be
mounted indoors or outdoors. The RCS-10 Remote Antenna Switch selects
one-of-eight “antenna” connectors or “ports”, and connects those ports directly
to a single common port for a feedline. The RCS-10 wil l work well in nearly
any system requiri ng switching of unbal anced or coaxial l ines, especial ly
those requiring good qual ity 50-ohm RF switches. The RCS-10 is a remote
control led switch usi ng relay contacts. The control head can be conveniently
located and only requires use of small low-voltage l ow-current telephone-type
fourconductor control cabl e. Any swi tch port can be used as either an input or
output, so you can sel ect one-of-eight radi os to one feedli ne or one-of-eight
antennas to a radio. The Main Advantages of the RCS-10 are wiring cost,
appearance, and convenience. The RCS-10 uses low voltage and low
current, and can use inexpensive and easy-to-route control cabl es. Bulky and
expensi ve coaxi al and control cables are not requi red, and wiring is very
simple. Si nce all cables route through one common point that can be
grounded, lightning protection is al most always significantly better than
conventi onal wiri ng methods using multi ple coaxial l ines into the operati ng
position. The RCS-10 Relay Unit reliabl y handles power levels in excess of
5,000 watts bel ow 30MHz, and power l evel s of 2.5kW at 50MHz. Port-to-port
isol ati on is typically i n the 40dB range, but varies with frequency and the
ports bei ng used. Loss is very low, and this switch can be considered lossless
below 30MHz. More performance details are i n the Remote Relay Unit
section of this manual. The RCS-10 Relay Unit can be used with any BCD
(bi nary coded decimal) 12-16 volt dc 400mA control system, such as the
RCS-12C Deluxe Control ler. (Thi s unit is shipped wi th a standard manual
RCS-10 controller.) The RCS-12C Deluxe Controller features push-button
antenna selecti on, memory, hot-swi tching protection, and automatic antenna
selection with band changes. The RCS-12C al lows manual selection of
multi ple antennas (up to eight possi ble antennas) on each band while locki ng
out any potential ly incorrect antenna choi ce! Ameritron RCS-10 Instructi on
Manual 2 The RCS-10 Indoor Unit (shipped with this unit) has antenna
indicator LED’s and a manual rotary selector switch. We have included an
area where you can label each antenna. It normally operates from +12 to +16
volt dc power supplies, and consumes less than 600mA. When used wi th other
rel ay systems, the RCS-10 (and RCS-12C) control units are capable of
switching up to 25 volts with one ampere of relay current. The RCS-10 Indoor
Uni t can be used as an interface to convert standard 1-of-8 control i nput to a
BCD output suitable for driving the RCS-10 remote relay box. The control
head al so outputs standard 1-of-8 control signals, like the RSC-8V system
uses. Control inputs must be 12 to 16 volts dc posi tive and capable of
supplying at least 400mA. This feature all ows other mul ti-wire control
systems, like the RCS-8V system, to interface with the RCS-10 controller. In all
cases, zero input or output vol tage selects antenna 1. The same output occurs
when voltage is appl ied to serial port one. Appl yi ng voltage to termi nal one
illuminates the position one LED, but the BCD output remai ns 000. See the
Control Logic Table on page 3 for swi tching detai ls.
1 pc: 4 770 Kč
1 pc: 848 Kč
RoHS
Foot Switches
MFJ-1709 FOOT SWITCH PTT
1 pc: 545 Kč
RoHS
FS-202 Foot operated push to talk
footswitch
GES08901151
Remote Coax Switch w/ lighting protection, 8-position,1.8-150 MHz;
5kW < 30MHz, 2,5kW / 50MHz
1 pc: 3 180 Kč
RoHS
The RCS-10 i s a versatile antenna switch desi gned for 50-ohm systems. It
handles high power, and sealed relays offer excellent life and connecti on
rel iabili ty. It requi res onl y three small i solated control wires, pl us a ground
return that can even can be the coaxial cable shield. The relay box can be
mounted indoors or outdoors. The RCS-10 Remote Antenna Switch selects
one-of-eight “antenna” connectors or “ports”, and connects those ports directly
to a single common port for a feedline. The RCS-10 wil l work well in nearly
any system requiri ng switching of unbal anced or coaxial l ines, especial ly
those requiring good qual ity 50-ohm RF switches. The RCS-10 is a remote
control led switch usi ng relay contacts. The control head can be conveniently
located and only requires use of small low-voltage l ow-current telephone-type
fourconductor control cabl e. Any swi tch port can be used as either an input or
output, so you can sel ect one-of-eight radi os to one feedli ne or one-of-eight
antennas to a radio. The Main Advantages of the RCS-10 are wiring cost,
appearance, and convenience. The RCS-10 uses low voltage and low
current, and can use inexpensive and easy-to-route control cabl es. Bulky and
expensi ve coaxi al and control cables are not requi red, and wiring is very
simple. Si nce all cables route through one common point that can be
grounded, lightning protection is al most always significantly better than
conventi onal wiri ng methods using multi ple coaxial l ines into the operati ng
position. The RCS-10 Relay Unit reliabl y handles power levels in excess of
5,000 watts bel ow 30MHz, and power l evel s of 2.5kW at 50MHz. Port-to-port
isol ati on is typically i n the 40dB range, but varies with frequency and the
ports bei ng used. Loss is very low, and this switch can be considered lossless
below 30MHz. More performance details are i n the Remote Relay Unit
section of this manual. The RCS-10 Relay Unit can be used with any BCD
(bi nary coded decimal) 12-16 volt dc 400mA control system, such as the
RCS-12C Deluxe Control ler. (Thi s unit is shipped wi th a standard manual
RCS-10 controller.) The RCS-12C Deluxe Controller features push-button
antenna selecti on, memory, hot-swi tching protection, and automatic antenna
selection with band changes. The RCS-12C al lows manual selection of
multi ple antennas (up to eight possi ble antennas) on each band while locki ng
out any potential ly incorrect antenna choi ce! Ameritron RCS-10 Instructi on
Manual 2 The RCS-10 Indoor Unit (shipped with this unit) has antenna
indicator LED’s and a manual rotary selector switch. We have included an
area where you can label each antenna. It normally operates from +12 to +16
volt dc power supplies, and consumes less than 600mA. When used wi th other
rel ay systems, the RCS-10 (and RCS-12C) control units are capable of
switching up to 25 volts with one ampere of relay current. The RCS-10 Indoor
Uni t can be used as an interface to convert standard 1-of-8 control i nput to a
BCD output suitable for driving the RCS-10 remote relay box. The control
head al so outputs standard 1-of-8 control signals, like the RSC-8V system
uses. Control inputs must be 12 to 16 volts dc posi tive and capable of
supplying at least 400mA. This feature all ows other mul ti-wire control
systems, like the RCS-8V system, to interface with the RCS-10 controller. In all
cases, zero input or output vol tage selects antenna 1. The same output occurs
when voltage is appl ied to serial port one. Appl yi ng voltage to termi nal one
illuminates the position one LED, but the BCD output remai ns 000. See the
Control Logic Table on page 3 for swi tching detai ls.
1 pc: 5 790 Kč
RoHS
GES07004725
Foot switch, for stage equipment switching. Ideally suited for guitar
amplifiers .
2 x on/off switchi ng function Metal case, 5 m connection cable wi th 6.3 mm
stereo plug
RoHS
RCS-10LX REMOTE COAX SWITCH
GES08900449
PTT Operator Foot Switch. 2-1/2Wx3-1/2Dx1-1/4H. 1/4in.phone
plug
1 pc: 599 Kč
RoHS
FS-3 Foot operated push to talk
footswitch
GES07004677
HEIL Dual Footswitch for PTT controlling
T he FS 3 i s a single channel foot swi tch to control the transmit/receive
function of an amateur radi o transcei ver. An 8' shielded cabl e is terminated
with a commercial 1/4" pl ug connects into the Heil CC-1 and AD-1 cable
system. T he hinge bar i s a solid chrome rod runni ng through the top and
bottom plates el iminating threaded screws that usuall y work loose. The hinge
bar is secured with 'C' fasteners.
1 pc: 690 Kč
RoHS
FS-2 Foot operated push to talk
PTT dual footswitch
Low Pass Filter LPS144
1kW/144MHz
GES08901506
HEIL Dual PTT Footswitch for controlling two devices
simultaneous ly
Low Pass Filter 144MHz, 50 Ohms, Ins.loss <0,07dB, SWRinput
>30dB, 1kWmax., 40dB/432MHz
Filters for transmitter - TX
MFJ-702B ANTENNA LOW PASS
FILTER
GES08902223
GES08901082
Low Pass Filter 100W, 1.5-30MHz/0.5dB m ax., 50Ohm, SWR 1.5:1
FS-2 Heil Dual Footswitch is a rugged, ergonomicall y correct device for
control ling two devices si multaneously. Two 10 AMP mi croswi tches key a
TCVR (leading, red) and PA (last, black). The Heil FS-2 is a unique product
speci all y designed for controlling two devi ces simultaneously. A typical
appli cation would be to key a transceiver with the BLACK lead and an RF
power ampl ifier wi th the RED l ead. Because of the design architecture, the
mi cro-switch controlling the RED lead keys up first as the foot switch i s
depressed, thus the RED l ead turns on before the BLACK lead thus insuri ng
that the amplifi er is keyed first before dri ve is appli ed from the transceiver that
keys up last in the sequence. The Heil FS-2 features an ergonomical ly correct
foot switch wi th the hi nge under your heel which requires much l ess effort and
rel axes the shin muscles during l ong periods of operation, such as contest and
DxPedion operati ons. The hi nge is a solid bar runni ng through the entire top
and bottom plates, eliminating threaded screws or fasteners that may work
loose. The FS-2 has been designed for maximum comfort and reliabil ity. T he
Hei l FS-2 Dual Channel Foot Switch terminates into a 1/4" and RCA. T he
RCA is common wi th many of the amplifier keyi ng input connectors. The RED
lead that wi ll control your amplifi er can easi ly be fitted i n the fiel d with other
types of connectors. The wire is easily soldered should you need to remove
the RED amplifier lead. The 1/4" mal e BLACK lead connects into the 1/4"
female pi g tail of the Heil CC-1 connecti ng microphone cable assembl y, thus
control ling the push to tal k line of the exciter.
1 pc: 1 195 Kč
Be a good neighbor. Pl ug this Low Pass TVI Fi lter between your transmitter
and antenna or tuner and reduce your transmitter harmonics by 50 dB!
Harmoni cs could be the source of i nterference to your neighbor's TV, radio,
VCR, telephone, etc. SWR i s below 1.5 to 30 MHz into 50 Ohms. Perfect for
barefoot transceivers -- handl es 200 Watts with less than 0.5 dB insertion loss.
Attenuation is 50 dB at 54 MHz. SO-239 connectors. 3x2x1 inches.
Low Pass Filter LPF144 for transmitter 144MHz, 50 Ohms. Use between
transmiter and antenna. Supress undesired thi rd harmonic product in 432MHz
band from transmi tter. Massive stabl e dural box, perfect N-connectors wi th
tefl on di electricum and sil ver plated middle contact, high quality low loss
special PTFE/woven fiberglass laminate Taconic TLX material for capacitors,
CuAg inductors. Impedance: 50 Ohms Input Return Loss 144MHz: >30dB
typical (SWR 1.07) Insertion Loss 144MHz: 0,07dB typical Attenuation
432MHz: 40dB typical Maximal power: 1kW (load SWR max 1.8) Dimensions:
130mm (138mm wi th connectors) x 60mm x 30mm
1 pc: 1 990 Kč
Action
RoHS
1 pc: 930 Kč
RoHS
MFJ-704 ANTENNA LOW PASS
FILTER
GES08901083
RFI and Noise Finders
MFJ-852 NOISE METER
Low Pass Filter (Chebyshev, 9poles) 1.8-30MHz / 52 Ohms / 1.5kW
RoHS
GES08900956
AC Power Line Noise Meter. Same as MFJ856, but without Yagi
antenna.
TVI, RFI, QRM Finding
Anti-TVI Filters for TV, Video etc.
HPF-1 ANTENNA ANTI-TVI HIGH
PASS FILTER
GES08901611
Anti-TVI Filter MFJ-704 is desi gned for Your transmitter. It is a Low Pass Fil ter
Chebyshev type, 9 poles, from MFJ (USA). Fi lter reduce T VI from amateur
transmitters by suppressing harmonical products above 30 MHz. Pass Band i s
0 to 30 MHz. Insertion Loss <0.5dB. Cut frequency 30MHz. Impedance 52
Ohms. Accepts up to 1500W. Connectors UHF (SO).
High Pass TVI Filter
1 pc: 1 590 Kč
RoHS
LP-30 ANTENNA LOW PASS
FILTER
Supress TVI with new 75 Ohm High Pass Filter from VECT RONICS (USA). Use
between cabl e and TV or VCR. Reduces signals below 30 MHz. Low loss <
0.5dB in T V passband 52-550MHz. Cutoff frequency 50MHz. Attenuati on
-60dB/10MHz,
-55dB/20MHz,
-40dB/30MHz.
Impedance
75
Ohm
unbalanced, 300 Ohm balanced. VSWR <1.5:1. Connectors F-CATV 75
Ohms.
GES08901614
Walk or dri ve around with these handhel d power line noi se meter to search
out leaky i nsulators, loose hardware and corroded ground lines qui ckl y. Track
noi se ri ght down to the pole, transformer or insulators. Operates i n 135MHz
region where activity is minimum and radiation from corona and arcing is far
more localized. Has 0.3uV sensitivity and wide-range AGC for noise level
meter - over 70dB. Plug in headphones and hear the noise you'are tracking or
plug tape recorder. Use this ul tra-sensiti ve RFI Detector to track down and
eleiminate RFI caused by radi ati ng cables and wires. MFJ-852 tell You
exactly which cable is radiating RFI so you can eli mi nate it with a simple
toroid or cl amp-on fi lter. Use it to find RFI generated by consumer devices,
computers and office equipment. When You eliminate the RFI source, hash,
birdies, whi stles and transient noise miracul ousli disappear. Measure 51 x 102
x 38mm. Use 9V bui ld-in battery.
1 pc: 3 190 Kč
Low Pass Chebys hev 9-pole Filter 0-30MHz/0.25dBmax;
1500Wmax; 52 Ohm s
RoHS
MFJ-856 NOISE FINDER
GES08901896
AC Power Line Noise Meter MFJ852, with 3el.Yagi Antenna
1 pc: 795 Kč
RoHS
HPF-2 ANTENNA ANTI-TVI HIGH
PASS FILTER
GES08901612
Deluxe High Pas s TVI Filter
Supress TVI with new 75 Ohm High Pass Fi lter od VECTRONICS (USA). Use
between cabl e and TV or VCR. Reduces signals below 30 MHz. Low loss <
0.5dB in T V passband 54-550MHz. Cutoff frequency 52MHz. Attenuati on
-90dB/10MHz,
-75dB/20MHz,
-60dB/30MHz.
Impedance
75
Ohm
unbalanced, 300 Ohm balanced. VSWR <1.5:1. Connectors F-CATV 75
Ohms.
1 pc: 590 Kč
Action
RoHS
TVIF-1 ANTENNA ANTI-TVI HIGH
PASS FILTER
GES08901775
High Pass TVI Filter. 48x42x22m m. TV-IEC m ale/female
connectors
Anti-TVI new LP-30 filter from VECTRONICS supress TVI from Your
transmitter. It is a Chebyshev type Low Pass Fi lter, nine pole. Fi lter suppress
harmonics appearing i n the TV bands and has additional attenuation to
TV-IF frequencies typi cal 70dB. Pass band 0 to 30 MHz. Inserti on Loss less
than 0.25dB. Cutoff frequency 30MHz. Typical attenuati on over 65dB above
60MHz. Impedance 52 Ohm. VSWR <1.3:1. Power Capacity 1500W.
Connectors UHF (PL, SO).
1 pc: 2 385 Kč
RoHS
LP-2500 ANTENNA LOW PASS
FILTER
GES08901613
Low Pass Chebys hev 9-pole Filter 0-30MHz/0.25dBmax; 2500W
cont.; 52 Ohm .
Connect new LP-2500 fi lter from VECT RONICS to Your transmitter and
suppress TVI. It is a Chebyshev type Low Pass Fil ter, nine pole. Filter suppress
harmonics appearing i n the TV bands and has additional attenuation to
TV-IF frequencies above 40MHz. Pass band 0 to 30 MHz. Insertion Loss less
than 0.25dB. Cutoff frequency 35MHz. Typical attenuati on over 60dB above
60MHz. Impedance 52 Ohm. VSWR <1.3:1. Power Capacity 2500W
Continuous, 4000W PEP. Connectors UHF (PL, SO). Dimensions 242 x 108 x
61mm. Weight 1.14kg.
High Quality Anti-T VI Fi lter for extremly effective RFI suppression from l ocal
amateur radio transmitter. Filter has correspondi ng TV-IEC male and female
connectors for connecti ng between TV receiver and coaxial antenna cable.
Impedance 75 Ohm. Typical attenuation 47dB/1.8-30MHz, 41dB/50-52MHz,
32dB/144-146dB,
III.TV
Band
3dB/174-230MHz,
IV-V.TV
Band
3.3dB/470-790MHz.
1 pc: 539 Kč
RoHS
1 pc: 3 690 Kč
RoHS
Walk or dri ve around with these handhel d power line noi se meter to search
out leaky i nsulators, loose hardware and corroded ground lines qui ckl y. Track
noi se ri ght down to the pole, transformer or insulators. Operates i n 135MHz
region where activity is minimum and radiation from corona and arcing is far
more localized. Has 0.3uV sensitivity and wide-range AGC for noise level
meter - over 70dB. Plug in headphones and hear the noise you'are tracking or
plug tape recorder. Use this ul tra-sensiti ve RFI Detector to track down and
eleiminate RFI caused by radiating cables and wires. MFJ856 tell You exactl y
which cable is radiating RFI so you can eliminate it wi th a simple toroid or
clamp-on filter. Use i t to find RFI generated by consumer devices, computers
and office equipment. When You eliminate the RFI source, hash, bi rdi es,
whistles and transi ent noi se mi raculously disappear. The MFJ856 is del ivered
with 3 element Yagfi antenna for pi npoint accurary. Use 9V bui ld-in battery
(not included).
1 pc: 4 290 Kč
RoHS
MFJ-9217 QRP CW TRANSCEIVER
17m / 5W
QRP
QRP TCVR's and Accessories
MFJ-9215 QRP CW TRANSCEIVER
15m / 5W
GES08902191
QRP Pocket CW TCVR, band 15m, output power 5W
NOTICE: MFJ-9215 Includes one band module 15M Additi onal Band
Modules Avai lable: MFJ-BM15 - 15 Meter Module MFJ-BM17 - 17 Meter
Module MFJ-BM20 - 20 Meter Module MFJ-BM30 - 30 Meter Module
MFJ-BM40 - 40 Meter Module MFJ-BM80 - 80 Meter Module MFJ-9200 is a
bold new addition to MFJ's l egendary QRP transcei ver l ine, del iveri ng
unmatched six-band CW performance in a compact pocket-sized package.
QRP radios have al ways been smal l in size, but thanks to direct-digi tal
synthesis and microprocessor technology, the MFJ-9200 represents a quantum
leap over traditi onal designs with an unprecedented number of features for a
very affordable price. The MFJ-9200 covers 80 through 15 Meters usi ng
computer-modeled pl ug-in filter modules that yield no-compromise receiver
performance and soli d QRP+ transmit power on every band. T here's also
built-in iambic keying wi th a manual-key sensor, a programmable CQ
message, and seamless QSK T/R swi tching. DDS frequency control delivers
rock-solid stabil ity, precise 100-Hz readout, and eight memory channels per
band. Plus, you get a choi ce of three main-dial tuning rates and RIT with
10-Hz tuning resol uti on. Other features incl ude sel ectable IF-band-wi dth for
moni toring SSB or CW, a 20-dB front-end attenuator for overload protection,
and a switched backl ight for the LCD display. There's also plenty of receiver
overlap for monitoring international short wave broadcasting. MFJ-9200 runs
on any power source between 8 and 15 VDC and draws a miserly 40 mA on
receive with the di splay backlight turned off -- perfect for prolonged
off-the-grid adventures. Best of all, the QR-Pocket Radio is the smallest and
lightest backpack transcei ver currently availabl e. MFJ also offers a wide range
of QRP accessori es to compliment the MFJ-9200 QRPocket CW
Transcei verTM. For example, the MFJ-561 Mini ature Iambi c Paddle is a
perfect companion when you're travel ing light. Also, consider picking up a
pair of MFJ-392B light-wei ght stereo headphones for cushi oned comfort and
cl ear sound during those long QRP contest sessi ons. For off-road adventure,
check out MFJ's line of Walkabout portable antennas that plug directly into
the QRPocket CW T ransceiver's BNC connector. MFJ-1899T, (see left) features
80 through 6 Meter coverage with a "wander-lead" tapped loadi ng coi l and
collapsi ble 52-inch whip. For mono-band coverage, consider the collapsible
MFJ-1880T, MFJ-1840T, MFJ-1830T, MFJ-1817T, or MFJ-1815T. For random
wire antennas, try the popular MFJ-902 mi niature travel tuner. Finall y, when
operating at home wi th your feet up, pl ug in the MFJ-4103 mini ature
switching power suppl y. The MFJ-9200 QRPocket CW Transcei ver comes
complete wi th one band module of your choosing, and modules for the other
bands. T ransceiver operation i s intuitive, easy-to-master, and clearly
expl ained in an easy-to-understand manual written by popul ar author and
QRP Hall of Fame member Rick Li ttlefield, K1BQT. We all know working rare
DX is exci ting, but being rare DX is a trul y indescribable! Given the MFJ-9200
QRPocket CW T ransceiver's diminuti ve size, features, wide coverage, and
soli d output, all of the i ngredients are here to turn your next vacation or
business trip into a expedition to remember! Specifi cations: Frequency
Control: DDS, 60-MHz reference frequency Tuning Step: 100-Hz, 1-kHz, and
100-kHz RIT Step: 10-Hz VFO Memori es: 8 per band VFO Displ ay: LCD,
802-pixel , switched backlight VFO Di splay Frequency Resolution: 100-Hz,
10-Hz with RIT activated Operating Modes: Transmi t - A1 (CW), Receive - A1,
A3J (LSB or USB) CW Offset: ~700 Hz T/R Switching: Full QSK Frequency
Coverage, MHz: Band: 80-M Receive: 3.2-4.9 Transmit: 3.5-4.0 40-M
Receive: 5.9-7.5 Transmit: 7.0-7.3 30-M Receive: 9.4-12.1 Transmit:
10.1-10.15 20-M Receive: 13.5-15.8 Transmit: 14.0-14.35 17-M Receive:
17.4-19.1 Transmit: 18.068-18.168 15-M Receive: 18.5-22.0 Transmit:
21.0-21.45 Receiver MDS: 0.1-uV, all bands AGC Threshold: 3 to 5-uV, all
bands Bandwidth: Selectable, 600-Hz CW, 2.5-Hz SSB Audio Output:
100-mW, 8-Ohm l oad, stereo plug Receiver Current Drain: ~40-mA no
backl ight, ~80 mA with backl ight Transmitter Keying: Iambi c automati c,
straight-key sensi ng, CQ memory Speed Range: 3-45 WPM Transmitter
Power: 5-W or better, all bands, at 12.6 Vol ts Harmonic and spur suppression:
-50 dB or better, all operating vol tages Typical Transmit Current: 0.9A at 10V,
1.2A at 14V Supply Voltage: 8-15 VDC at 1.5A Di mensi ons: 4.8"x3.15"x1.34",
120x80x34-mm Weight: 7.4 oz, 200 gm
1 pc: 5 990 Kč
RoHS
GES08902192
MFJ-9220 QRP CW TRANSCEIVER
20m / 5W
GES08902193
QRP Pocket CW TCVR, band 17m, output power 5W
QRP Pocket CW TCVR, band 20m, output power 5W
NOTICE: MFJ-9217 Includes one band module 17M Additional Band
Modules Avai lable: MFJ-BM15 - 15 Meter Module MFJ-BM17 - 17 Meter
Module MFJ-BM20 - 20 Meter Module MFJ-BM30 - 30 Meter Module
MFJ-BM40 - 40 Meter Module MFJ-BM80 - 80 Meter Module MFJ-9200 i s a
bold new addition to MFJ's l egendary QRP transcei ver l ine, del iveri ng
unmatched si x-band CW performance i n a compact pocket-sized package.
QRP radios have al ways been smal l i n size, but thanks to direct-digi tal
synthesis and microprocessor technology, the MFJ-9200 represents a quantum
leap over traditional designs with an unprecedented number of features for a
very affordable price. The MFJ-9200 covers 80 through 15 Meters usi ng
computer-modeled pl ug-in fi lter modules that yield no-compromi se receiver
performance and soli d QRP+ transmit power on every band. There's also
built-in iambic keying wi th a manual-key sensor, a programmable CQ
message, and seamless QSK T/R swi tching. DDS frequency control delivers
rock-solid stabil ity, preci se 100-Hz readout, and eight memory channels per
band. Plus, you get a choice of three main-dial tuning rates and RIT with
10-Hz tuning resol uti on. Other features include sel ectable IF-band-width for
moni toring SSB or CW, a 20-dB front-end attenuator for overload protection,
and a switched backl ight for the LCD display. There's also plenty of receiver
overlap for monitoring international short wave broadcasti ng. MFJ-9200 runs
on any power source between 8 and 15 VDC and draws a miserly 40 mA on
receive with the display backlight turned off -- perfect for prolonged
off-the-grid adventures. Best of all, the QR-Pocket Radio is the smal lest and
lightest backpack transcei ver currently availabl e. MFJ also offers a wide range
of QRP accessori es to compliment the MFJ-9200 QRPocket CW
Transcei verTM. For example, the MFJ-561 Mini ature Iambi c Paddle is a
perfect companion when you're travel ing light. Also, consider picking up a
pair of MFJ-392B light-wei ght stereo headphones for cushi oned comfort and
cl ear sound during those long QRP contest sessions. For off-road adventure,
check out MFJ's line of Walkabout portabl e antennas that plug directly into
the QRPocket CW T ransceiver's BNC connector. MFJ-1899T, (see left) features
80 through 6 Meter coverage wi th a "wander-l ead" tapped loadi ng coil and
collapsi ble 52-i nch whip. For mono-band coverage, consider the collapsible
MFJ-1880T, MFJ-1840T, MFJ-1830T, MFJ-1817T, or MFJ-1815T. For random
wire antennas, try the popular MFJ-902 mi niature travel tuner. Finall y, when
operating at home with your feet up, pl ug in the MFJ-4103 mini ature
switching power supply. The MFJ-9200 QRPocket CW Transcei ver comes
complete wi th one band module of your choosing, and modules for the other
bands. Transceiver operation i s intui tive, easy-to-master, and clearly
expl ained in an easy-to-understand manual written by popular author and
QRP Hall of Fame member Rick Littlefield, K1BQT. We all know working rare
DX is exci ting, but being rare DX is a trul y indescribabl e! Given the MFJ-9200
QRPocket CW Transceiver's diminuti ve size, features, wide coverage, and
soli d output, all of the i ngredients are here to turn your next vacation or
business tri p i nto a expedition to remember! Specifi cations: Frequency
Control: DDS, 60-MHz reference frequency Tuning Step: 100-Hz, 1-kHz, and
100-kHz RIT Step: 10-Hz VFO Memories: 8 per band VFO Displ ay: LCD,
802-pixel , switched backlight VFO Di splay Frequency Resolution: 100-Hz,
10-Hz with RIT activated Operating Modes: Transmi t - A1 (CW), Receive - A1,
A3J (LSB or USB) CW Offset: ~700 Hz T/R Switching: Full QSK Frequency
Coverage, MHz: Band: 80-M Recei ve: 3.2-4.9 Transmit: 3.5-4.0 40-M
Receive: 5.9-7.5 Transmit: 7.0-7.3 30-M Receive: 9.4-12.1 Transmit:
10.1-10.15 20-M Receive: 13.5-15.8 T ransmit: 14.0-14.35 17-M Receive:
17.4-19.1 Transmit: 18.068-18.168 15-M Receive: 18.5-22.0 Transmit:
21.0-21.45 Receiver MDS: 0.1-uV, al l bands AGC Threshold: 3 to 5-uV, all
bands Bandwidth: Selectable, 600-Hz CW, 2.5-Hz SSB Audio Output:
100-mW, 8-Ohm l oad, stereo plug Receiver Current Drain: ~40-mA no
backl ight, ~80 mA with backli ght Transmitter Keying: Iambic automati c,
straight-key sensing, CQ memory Speed Range: 3-45 WPM Transmitter
Power: 5-W or better, all bands, at 12.6 Vol ts Harmonic and spur suppression:
-50 dB or better, all operating vol tages Typical Transmit Current: 0.9A at 10V,
1.2A at 14V Supply Voltage: 8-15 VDC at 1.5A Di mensi ons: 4.8"x3.15"x1.34",
120x80x34-mm Weight: 7.4 oz, 200 gm
NOTICE: MFJ-9220 Includes one band module 20M Additional Band
Modules Avail able: MFJ-BM15 - 15 Meter Module MFJ-BM17 - 17 Meter
Module MFJ-BM20 - 20 Meter Module MFJ-BM30 - 30 Meter Module
MFJ-BM40 - 40 Meter Module MFJ-BM80 - 80 Meter Module MFJ-9200 i s a
bol d new addi tion to MFJ's legendary QRP transceiver li ne, deli vering
unmatched si x-band CW performance i n a compact pocket-sized package.
QRP radios have always been small i n size, but thanks to direct-di gital
synthesis and microprocessor technology, the MFJ-9200 represents a quantum
l eap over traditional designs wi th an unprecedented number of features for a
very affordabl e pri ce. The MFJ-9200 covers 80 through 15 Meters using
computer-modeled plug-in fi lter modules that yield no-compromi se receiver
performance and solid QRP+ transmi t power on every band. There's also
bui lt-i n iambic keying with a manual-key sensor, a programmable CQ
message, and seamless QSK T/R switching. DDS frequency control del ivers
rock-solid stabili ty, preci se 100-Hz readout, and ei ght memory channels per
band. Pl us, you get a choice of three mai n-dial tuning rates and RIT wi th
10-Hz tuning resolution. Other features include selectable IF-band-width for
monitori ng SSB or CW, a 20-dB front-end attenuator for overload protection,
and a switched backli ght for the LCD displ ay. T here's al so plenty of receiver
overl ap for moni toring i nternati onal short wave broadcasti ng. MFJ-9200 runs
on any power source between 8 and 15 VDC and draws a miserly 40 mA on
recei ve with the display backl ight turned off -- perfect for prolonged
off-the-grid adventures. Best of all, the QR-Pocket Radio is the smal lest and
l ightest backpack transceiver currently available. MFJ also offers a wide range
of QRP accessories to compl iment the MFJ-9200 QRPocket CW
T ransceiverTM. For example, the MFJ-561 Mi niature Iambic Paddle is a
perfect companion when you're traveli ng light. Also, consider picking up a
pai r of MFJ-392B l ight-weight stereo headphones for cushioned comfort and
clear sound during those l ong QRP contest sessions. For off-road adventure,
check out MFJ's line of Walkabout portabl e antennas that pl ug directly into
the QRPocket CW Transceiver's BNC connector. MFJ-1899T, (see l eft) features
80 through 6 Meter coverage wi th a "wander-l ead" tapped l oading coil and
collapsible 52-i nch whip. For mono-band coverage, consi der the col lapsible
MFJ-1880T, MFJ-1840T, MFJ-1830T, MFJ-1817T, or MFJ-1815T. For random
wire antennas, try the popular MFJ-902 miniature travel tuner. Finally, when
operating at home with your feet up, plug in the MFJ-4103 mi niature
switchi ng power supply. The MFJ-9200 QRPocket CW T ransceiver comes
complete with one band modul e of your choosing, and modules for the other
bands. Transceiver operati on is intui tive, easy-to-master, and clearl y
explained in an easy-to-understand manual written by popular author and
QRP Hal l of Fame member Rick Littlefield, K1BQT. We al l know working rare
DX i s exciting, but being rare DX i s a truly indescribabl e! Given the MFJ-9200
QRPocket CW Transceiver's diminutive size, features, wide coverage, and
solid output, all of the ingredients are here to turn your next vacati on or
busi ness tri p i nto a expedi tion to remember! Specifications: Frequency
Control: DDS, 60-MHz reference frequency Tuning Step: 100-Hz, 1-kHz, and
100-kHz RIT Step: 10-Hz VFO Memories: 8 per band VFO Di splay: LCD,
802-pixel, swi tched backl ight VFO Display Frequency Resol uti on: 100-Hz,
10-Hz with RIT activated Operati ng Modes: Transmit - A1 (CW), Receive - A1,
A3J (LSB or USB) CW Offset: ~700 Hz T/R Switchi ng: Full QSK Frequency
Coverage, MHz: Band: 80-M Recei ve: 3.2-4.9 Transmit: 3.5-4.0 40-M
Recei ve: 5.9-7.5 Transmit: 7.0-7.3 30-M Receive: 9.4-12.1 T ransmit:
10.1-10.15 20-M Receive: 13.5-15.8 T ransmit: 14.0-14.35 17-M Receive:
17.4-19.1 Transmit: 18.068-18.168 15-M Receive: 18.5-22.0 T ransmit:
21.0-21.45 Receiver MDS: 0.1-uV, al l bands AGC T hreshold: 3 to 5-uV, all
bands Bandwi dth: Selectable, 600-Hz CW, 2.5-Hz SSB Audi o Output:
100-mW, 8-Ohm load, stereo plug Recei ver Current Drain: ~40-mA no
backli ght, ~80 mA wi th backli ght Transmitter Keying: Iambic automatic,
strai ght-key sensing, CQ memory Speed Range: 3-45 WPM Transmitter
Power: 5-W or better, al l bands, at 12.6 Volts Harmonic and spur suppression:
-50 dB or better, all operating voltages Typical T ransmit Current: 0.9A at 10V,
1.2A at 14V Suppl y Voltage: 8-15 VDC at 1.5A Dimensions: 4.8"x3.15"x1.34",
120x80x34-mm Weight: 7.4 oz, 200 gm
1 pc: 5 990 Kč
RoHS
1 pc: 4 990 Kč
Action
RoHS
MFJ-9230 QRP CW TRANSCEIVER
30m / 5W
GES08902194
MFJ-9240 QRP CW TRANSCEIVER
40m / 5W
GES08902195
MFJ-9280 QRP CW TRANSCEIVER
80m / 5W
GES08902196
QRP Pocket CW TCVR, band 30m, output power 5W
QRP Pocket CW TCVR, band 40m, output power 5W
QRP Pocket CW TCVR, band 80m, output power 5W
NOTICE: MFJ-9230 Includes one band module 30M Additi onal Band
Modules Avai lable: MFJ-BM15 - 15 Meter Module MFJ-BM17 - 17 Meter
Module MFJ-BM20 - 20 Meter Module MFJ-BM30 - 30 Meter Module
MFJ-BM40 - 40 Meter Module MFJ-BM80 - 80 Meter Module MFJ-9200 is a
bold new addition to MFJ's l egendary QRP transcei ver l ine, del iveri ng
unmatched six-band CW performance in a compact pocket-sized package.
QRP radios have al ways been smal l in size, but thanks to direct-digi tal
synthesis and microprocessor technology, the MFJ-9200 represents a quantum
leap over traditi onal designs with an unprecedented number of features for a
very affordable price. The MFJ-9200 covers 80 through 15 Meters usi ng
computer-modeled pl ug-in filter modules that yield no-compromise receiver
performance and soli d QRP+ transmit power on every band. T here's also
built-in iambic keying wi th a manual-key sensor, a programmable CQ
message, and seamless QSK T/R swi tching. DDS frequency control delivers
rock-solid stabil ity, precise 100-Hz readout, and eight memory channels per
band. Plus, you get a choi ce of three main-dial tuning rates and RIT with
10-Hz tuning resol uti on. Other features incl ude sel ectable IF-band-wi dth for
moni toring SSB or CW, a 20-dB front-end attenuator for overload protection,
and a switched backl ight for the LCD display. There's also plenty of receiver
overlap for monitoring international short wave broadcasting. MFJ-9200 runs
on any power source between 8 and 15 VDC and draws a miserly 40 mA on
receive with the di splay backlight turned off -- perfect for prolonged
off-the-grid adventures. Best of all, the QR-Pocket Radio is the smallest and
lightest backpack transcei ver currently availabl e. MFJ also offers a wide range
of QRP accessori es to compliment the MFJ-9200 QRPocket CW
Transcei verTM. For example, the MFJ-561 Mini ature Iambi c Paddle is a
perfect companion when you're travel ing light. Also, consider picking up a
pair of MFJ-392B light-wei ght stereo headphones for cushi oned comfort and
cl ear sound during those long QRP contest sessi ons. For off-road adventure,
check out MFJ's line of Walkabout portable antennas that plug directly into
the QRPocket CW T ransceiver's BNC connector. MFJ-1899T, (see left) features
80 through 6 Meter coverage with a "wander-lead" tapped loadi ng coi l and
collapsi ble 52-inch whip. For mono-band coverage, consider the collapsible
MFJ-1880T, MFJ-1840T, MFJ-1830T, MFJ-1817T, or MFJ-1815T. For random
wire antennas, try the popular MFJ-902 mi niature travel tuner. Finall y, when
operating at home wi th your feet up, pl ug in the MFJ-4103 mini ature
switching power suppl y. The MFJ-9200 QRPocket CW Transcei ver comes
complete wi th one band module of your choosing, and modules for the other
bands. T ransceiver operation i s intuitive, easy-to-master, and clearly
expl ained in an easy-to-understand manual written by popul ar author and
QRP Hall of Fame member Rick Li ttlefield, K1BQT. We all know working rare
DX is exci ting, but being rare DX is a trul y indescribable! Given the MFJ-9200
QRPocket CW T ransceiver's diminuti ve size, features, wide coverage, and
soli d output, all of the i ngredients are here to turn your next vacation or
business trip into a expedition to remember! Specifi cations: Frequency
Control: DDS, 60-MHz reference frequency Tuning Step: 100-Hz, 1-kHz, and
100-kHz RIT Step: 10-Hz VFO Memori es: 8 per band VFO Displ ay: LCD,
802-pixel , switched backlight VFO Di splay Frequency Resolution: 100-Hz,
10-Hz with RIT activated Operating Modes: Transmi t - A1 (CW), Receive - A1,
A3J (LSB or USB) CW Offset: ~700 Hz T/R Switching: Full QSK Frequency
Coverage, MHz: Band: 80-M Receive: 3.2-4.9 Transmit: 3.5-4.0 40-M
Receive: 5.9-7.5 Transmit: 7.0-7.3 30-M Receive: 9.4-12.1 Transmit:
10.1-10.15 20-M Receive: 13.5-15.8 Transmit: 14.0-14.35 17-M Receive:
17.4-19.1 Transmit: 18.068-18.168 15-M Receive: 18.5-22.0 Transmit:
21.0-21.45 Receiver MDS: 0.1-uV, all bands AGC Threshold: 3 to 5-uV, all
bands Bandwidth: Selectable, 600-Hz CW, 2.5-Hz SSB Audio Output:
100-mW, 8-Ohm l oad, stereo plug Receiver Current Drain: ~40-mA no
backl ight, ~80 mA with backl ight Transmitter Keying: Iambi c automati c,
straight-key sensi ng, CQ memory Speed Range: 3-45 WPM Transmitter
Power: 5-W or better, all bands, at 12.6 Vol ts Harmonic and spur suppression:
-50 dB or better, all operating vol tages Typical Transmit Current: 0.9A at 10V,
1.2A at 14V Supply Voltage: 8-15 VDC at 1.5A Di mensi ons: 4.8"x3.15"x1.34",
120x80x34-mm Weight: 7.4 oz, 200 gm
NOTICE: MFJ-9240 Includes one band module 40M Additional Band
Modules Avai lable: MFJ-BM15 - 15 Meter Module MFJ-BM17 - 17 Meter
Module MFJ-BM20 - 20 Meter Module MFJ-BM30 - 30 Meter Module
MFJ-BM40 - 40 Meter Module MFJ-BM80 - 80 Meter Module MFJ-9200 i s a
bold new addition to MFJ's l egendary QRP transcei ver l ine, del iveri ng
unmatched si x-band CW performance i n a compact pocket-sized package.
QRP radios have al ways been smal l i n size, but thanks to direct-digi tal
synthesis and microprocessor technology, the MFJ-9200 represents a quantum
leap over traditional designs with an unprecedented number of features for a
very affordable price. The MFJ-9200 covers 80 through 15 Meters usi ng
computer-modeled pl ug-in fi lter modules that yield no-compromi se receiver
performance and soli d QRP+ transmit power on every band. There's also
built-in iambic keying wi th a manual-key sensor, a programmable CQ
message, and seamless QSK T/R swi tching. DDS frequency control delivers
rock-solid stabil ity, preci se 100-Hz readout, and eight memory channels per
band. Plus, you get a choice of three main-dial tuning rates and RIT with
10-Hz tuning resol uti on. Other features include sel ectable IF-band-width for
moni toring SSB or CW, a 20-dB front-end attenuator for overload protection,
and a switched backl ight for the LCD display. There's also plenty of receiver
overlap for monitoring international short wave broadcasti ng. MFJ-9200 runs
on any power source between 8 and 15 VDC and draws a miserly 40 mA on
receive with the display backlight turned off -- perfect for prolonged
off-the-grid adventures. Best of all, the QR-Pocket Radio is the smal lest and
lightest backpack transcei ver currently availabl e. MFJ also offers a wide range
of QRP accessori es to compliment the MFJ-9200 QRPocket CW
Transcei verTM. For example, the MFJ-561 Mini ature Iambi c Paddle is a
perfect companion when you're travel ing light. Also, consider picking up a
pair of MFJ-392B light-wei ght stereo headphones for cushi oned comfort and
cl ear sound during those long QRP contest sessions. For off-road adventure,
check out MFJ's line of Walkabout portabl e antennas that plug directly into
the QRPocket CW T ransceiver's BNC connector. MFJ-1899T, (see left) features
80 through 6 Meter coverage wi th a "wander-l ead" tapped loadi ng coil and
collapsi ble 52-i nch whip. For mono-band coverage, consider the collapsible
MFJ-1880T, MFJ-1840T, MFJ-1830T, MFJ-1817T, or MFJ-1815T. For random
wire antennas, try the popular MFJ-902 mi niature travel tuner. Finall y, when
operating at home with your feet up, pl ug in the MFJ-4103 mini ature
switching power supply. The MFJ-9200 QRPocket CW Transcei ver comes
complete wi th one band module of your choosing, and modules for the other
bands. Transceiver operation i s intui tive, easy-to-master, and clearly
expl ained in an easy-to-understand manual written by popular author and
QRP Hall of Fame member Rick Littlefield, K1BQT. We all know working rare
DX is exci ting, but being rare DX is a trul y indescribabl e! Given the MFJ-9200
QRPocket CW Transceiver's diminuti ve size, features, wide coverage, and
soli d output, all of the i ngredients are here to turn your next vacation or
business tri p i nto a expedition to remember! Specifi cations: Frequency
Control: DDS, 60-MHz reference frequency Tuning Step: 100-Hz, 1-kHz, and
100-kHz RIT Step: 10-Hz VFO Memories: 8 per band VFO Displ ay: LCD,
802-pixel , switched backlight VFO Di splay Frequency Resolution: 100-Hz,
10-Hz with RIT activated Operating Modes: Transmi t - A1 (CW), Receive - A1,
A3J (LSB or USB) CW Offset: ~700 Hz T/R Switching: Full QSK Frequency
Coverage, MHz: Band: 80-M Recei ve: 3.2-4.9 Transmit: 3.5-4.0 40-M
Receive: 5.9-7.5 Transmit: 7.0-7.3 30-M Receive: 9.4-12.1 Transmit:
10.1-10.15 20-M Receive: 13.5-15.8 T ransmit: 14.0-14.35 17-M Receive:
17.4-19.1 Transmit: 18.068-18.168 15-M Receive: 18.5-22.0 Transmit:
21.0-21.45 Receiver MDS: 0.1-uV, al l bands AGC Threshold: 3 to 5-uV, all
bands Bandwidth: Selectable, 600-Hz CW, 2.5-Hz SSB Audio Output:
100-mW, 8-Ohm l oad, stereo plug Receiver Current Drain: ~40-mA no
backl ight, ~80 mA with backli ght Transmitter Keying: Iambic automati c,
straight-key sensing, CQ memory Speed Range: 3-45 WPM Transmitter
Power: 5-W or better, all bands, at 12.6 Vol ts Harmonic and spur suppression:
-50 dB or better, all operating vol tages Typical Transmit Current: 0.9A at 10V,
1.2A at 14V Supply Voltage: 8-15 VDC at 1.5A Di mensi ons: 4.8"x3.15"x1.34",
120x80x34-mm Weight: 7.4 oz, 200 gm
NOTICE: MFJ-9280 Includes one band module 80M Additional Band
Modules Avail able: MFJ-BM15 - 15 Meter Module MFJ-BM17 - 17 Meter
Module MFJ-BM20 - 20 Meter Module MFJ-BM30 - 30 Meter Module
MFJ-BM40 - 40 Meter Module MFJ-BM80 - 80 Meter Module MFJ-9200 i s a
bol d new addi tion to MFJ's legendary QRP transceiver li ne, deli vering
unmatched si x-band CW performance i n a compact pocket-sized package.
QRP radios have always been small i n size, but thanks to direct-di gital
synthesis and microprocessor technology, the MFJ-9200 represents a quantum
l eap over traditional designs wi th an unprecedented number of features for a
very affordabl e pri ce. The MFJ-9200 covers 80 through 15 Meters using
computer-modeled plug-in fi lter modules that yield no-compromi se receiver
performance and solid QRP+ transmi t power on every band. There's also
bui lt-i n iambic keying with a manual-key sensor, a programmable CQ
message, and seamless QSK T/R switching. DDS frequency control del ivers
rock-solid stabili ty, preci se 100-Hz readout, and ei ght memory channels per
band. Pl us, you get a choice of three mai n-dial tuning rates and RIT wi th
10-Hz tuning resolution. Other features include selectable IF-band-width for
monitori ng SSB or CW, a 20-dB front-end attenuator for overload protection,
and a switched backli ght for the LCD displ ay. T here's al so plenty of receiver
overl ap for moni toring i nternati onal short wave broadcasti ng. MFJ-9200 runs
on any power source between 8 and 15 VDC and draws a miserly 40 mA on
recei ve with the display backl ight turned off -- perfect for prolonged
off-the-grid adventures. Best of all, the QR-Pocket Radio is the smal lest and
l ightest backpack transceiver currently available. MFJ also offers a wide range
of QRP accessories to compl iment the MFJ-9200 QRPocket CW
T ransceiverTM. For example, the MFJ-561 Mi niature Iambic Paddle is a
perfect companion when you're traveli ng light. Also, consider picking up a
pai r of MFJ-392B l ight-weight stereo headphones for cushioned comfort and
clear sound during those l ong QRP contest sessions. For off-road adventure,
check out MFJ's line of Walkabout portabl e antennas that pl ug directly into
the QRPocket CW Transceiver's BNC connector. MFJ-1899T, (see l eft) features
80 through 6 Meter coverage wi th a "wander-l ead" tapped l oading coil and
collapsible 52-i nch whip. For mono-band coverage, consi der the col lapsible
MFJ-1880T, MFJ-1840T, MFJ-1830T, MFJ-1817T, or MFJ-1815T. For random
wire antennas, try the popular MFJ-902 miniature travel tuner. Finally, when
operating at home with your feet up, plug in the MFJ-4103 mi niature
switchi ng power supply. The MFJ-9200 QRPocket CW T ransceiver comes
complete with one band modul e of your choosing, and modules for the other
bands. Transceiver operati on is intui tive, easy-to-master, and clearl y
explained in an easy-to-understand manual written by popular author and
QRP Hal l of Fame member Rick Littlefield, K1BQT. We al l know working rare
DX i s exciting, but being rare DX i s a truly indescribabl e! Given the MFJ-9200
QRPocket CW Transceiver's diminutive size, features, wide coverage, and
solid output, all of the ingredients are here to turn your next vacati on or
busi ness tri p i nto a expedi tion to remember! Specifications: Frequency
Control: DDS, 60-MHz reference frequency Tuning Step: 100-Hz, 1-kHz, and
100-kHz RIT Step: 10-Hz VFO Memories: 8 per band VFO Di splay: LCD,
802-pixel, swi tched backl ight VFO Display Frequency Resol uti on: 100-Hz,
10-Hz with RIT activated Operati ng Modes: Transmit - A1 (CW), Receive - A1,
A3J (LSB or USB) CW Offset: ~700 Hz T/R Switchi ng: Full QSK Frequency
Coverage, MHz: Band: 80-M Recei ve: 3.2-4.9 Transmit: 3.5-4.0 40-M
Recei ve: 5.9-7.5 Transmit: 7.0-7.3 30-M Receive: 9.4-12.1 T ransmit:
10.1-10.15 20-M Receive: 13.5-15.8 T ransmit: 14.0-14.35 17-M Receive:
17.4-19.1 Transmit: 18.068-18.168 15-M Receive: 18.5-22.0 T ransmit:
21.0-21.45 Receiver MDS: 0.1-uV, al l bands AGC T hreshold: 3 to 5-uV, all
bands Bandwi dth: Selectable, 600-Hz CW, 2.5-Hz SSB Audi o Output:
100-mW, 8-Ohm load, stereo plug Recei ver Current Drain: ~40-mA no
backli ght, ~80 mA wi th backli ght Transmitter Keying: Iambic automatic,
strai ght-key sensing, CQ memory Speed Range: 3-45 WPM Transmitter
Power: 5-W or better, al l bands, at 12.6 Volts Harmonic and spur suppression:
-50 dB or better, all operating voltages Typical T ransmit Current: 0.9A at 10V,
1.2A at 14V Suppl y Voltage: 8-15 VDC at 1.5A Dimensions: 4.8"x3.15"x1.34",
120x80x34-mm Weight: 7.4 oz, 200 gm
1 pc: 4 990 Kč
Action
RoHS
1 pc: 5 990 Kč
RoHS
1 pc: 5 990 Kč
RoHS
MFJ-BM15 BAND MODUL 15m QRP CW TRANSCEIVER
GES08902197
Band Module for QRP CW transceiver MFJ-9200 series
Additional Band Modules Avail able: MFJ-BM15 - 15 Meter Module
MFJ-BM17 - 17 Meter Modul e MFJ-BM20 - 20 Meter Module MFJ-BM30 - 30
Meter Module MFJ-BM40 - 40 Meter Module MFJ-BM80 - 80 Meter Module
1 pc: 490.00 Kč
Action
RoHS
MFJ-BM17 BAND MODUL 17m QRP CW TRANSCEIVER
GES08902198
Band Module for QRP CW transceiver MFJ-9200 series
1 pc: 490.00 Kč
Action
RoHS
MFJ-BM20 BAND MODUL 20m QRP CW TRANSCEIVER
GES08902199
Band Module for QRP CW transceiver MFJ-9200 series
1 pc: 795 Kč
RoHS
MFJ-BM30 BAND MODUL 30m QRP CW TRANSCEIVER
GES08902200
Band Module for QRP CW transceiver MFJ-9200 series
1 pc: 490.00 Kč
Action
RoHS
MFJ-BM40 BAND MODUL 40m QRP CW TRANSCEIVER
GES08902201
Band Module for QRP CW transceiver MFJ-9200 series
1 pc: 795 Kč
RoHS
MFJ-BM80 BAND MODUL 80m QRP CW TRANSCEIVER
GES08902202
Band Module for QRP CW transceiver MFJ-9200 series
1 pc: 495.00 Kč
Action
RoHS
MFJ-9201 QRP Antenna Tuner
80-10m / 100W
GES08902186
MFJ-1046 RF RX PRESELECTOR
GES08900335
Receiver Passive Preselector 1.6-33 MHz
MFJ-561KIT MINI IAMBIC PADDLES
GES08900295
Miniature Travel Iambic Paddle Kit
QRP Antenna Tuner specially compact-built for MFJ-9215,
MFJ-9217, MFJ-9230, MFJ-9240, MFJ-9280
1 pc: 530 Kč
RoHS
MFJ-564 IAMBIC PADDLES
GES08900296
Deluxe Iambic Chrom e Paddle
MFJs new Passi ve Preselector has extremel y hi gh dynamic range! It improves
the performance of nearly any HF or shortwave recei ver/transceiver. It vastly
improves the most expensive receivers. Especially helpful to those with
broadband front-ends that are prone to overload.
Custom 12 position i nductor switch, tune/bypass switch, antenna and
transmitter capacitors, BNC feedpoints for antenna and transmitter
connecti ons. Handles 100W RF output. It’s a tiny 4" x 2 5/8" x 1 1/2", so it and
your MFJ-9200 (MFJ-9215, MFJ-9217, MFJ-9230, MFJ-9240 or MFJ-9280)
transcei ver package and antennas can easily sl ide into a backpack or small
bri efcase to take along wi th you on your next fiel d day, DXpedition, vacati on
or business trip.
1 pc: 1 350 Kč
RoHS
MFJ-9211 QRP Current Balun 4:1
GES08902190
QRP Pocket Balun
Protects your sensiti ve receiver input from damage (including switchi ng
diodes and attenuator resistors) caused by very strong signals from multi
transmitter, multi-band operation during contests, fiel d day, nearby hams,
CBers, T V/FM/AM stations.
It el iminates phantom signals by suppressing strong out-of-band signals that
cause intermod, blocki ng and cross modulation. Completel y el iminates
second order intermod problems caused by strong out-of-band shortwave
broadcast signal s mixing and producing unwanted in band si gnals.
MFJs unique Hi-Q series tunabl e circuit gives you superb performance. T he
tunable series tuned circui t works i nto a very low impedance formed by
broadband toroid transformers.
1 pc: 1 850 Kč
RoHS
MFJ-564B IAMBIC PADDLES
GES08900297
Deluxe Iambic Black Paddle
Has narrow bandwi dth, excellent stopband attenuation, very low loss, constant
bandwidth and gain over each band. Excel lent attenuati on in adjacent
contest bands.
The enti re 1.6 to 33 MHz HF band is covered in five overlappi ng bands. An
air vari able tuning capaci tor, 1.8 to 1 tuning range and a verni er reducti on
dri ve gives you preci sion tuni ng.
Fully shiel ded metal enclosure. Tough bl ack fi nish.
1 pc: 3 180 Kč
RoHS
1 pc: 530 Kč
Morse (CW)
1 pc: 1 850 Kč
RoHS
RoHS
BY-I IAMBIC PADDLES
GES08900292
Bencher Iambic Paddle - Black Chrome
Straight Keys
RX Accessories
MFJ-550 STRAIGHT KEY
GES08900290
Telegraph Key
Preselectors
MFJ-1045C RF RX PRESELECTOR
GES08901081
Preselector for Receiver, tunable 1-54 MHz
1 pc: 3 450 Kč
RoHS
BY-II IAMBIC PADDLES
GES08900293
Bencher Iambic Paddle - Chrome
1 pc: 395.00 Kč
RoHS
MFJ-557 STRAIGHT KEY WITH
OSCILATOR
GES08900291
Code Practice Os ciIator with Key
Lets you copy weak si gnals. Rejects out-of-band signal s, images. 1.8 to 54
MHz. Up to 20 dB gain. Gain control. Dual gate MOSFET, bipolar transi stors
for l ow noise, high gain. Connect 2 antennas, 2 receivers. Coax and phone
jacks. Power suppl y: replaceable 9V buil t-in battery or an external optional
DC adapter 9 - 18VDC (the MW 300 GES 075 000 61 from
GES-ELECTRONICS) may be plugged in.
1 pc: 2 380 Kč
RoHS
BY-2 Iambie Paddle. Chrome Base, Chrome Components.
1 pc: 4 190 Kč
RoHS
Electronic Keyers
1 pc: 1 060 Kč
MFJ-407D ELBUG
RoHS
GES08900700
MFJ Curtis Deluxe Keyer
Key Paddle
MFJ-561 MINI IAMBIC PADDLES
GES08900294
Miniature Travel Iambic Paddle
T he MFJ407D Del uxe El ectroni c Keyer is a microprocessor controll ed keyer
that provides i ambi c key operation and dot-and-dash memory to make
sending perfect code easier. It has tunable code speed, code wei ght, and
si detone frequency; it suports both direct and gri d-block keyi ng outputs. You
also get to choose Iambi c Type "A" and Type "B" keying. Works with MFJ564
or Bencher BY-I or BY-II or other iambic paddle. Power supply is a internal 9V
battery (not i ncluded) or a external power supply 12V. We recommend our
MW300 or MW9V/1A or MW501 .
1 pc: 490.00 Kč
Action
RoHS
1 pc: 2 090 Kč
RoHS
MFJ-490 ELBUG - MEMORY KEYER
MFJ-902H ANTENNA TUNER
GES08900299
Memory Keyer/Bencher Com bo for traffic, contest and code
practice
GES08901065
Travel tuner 10-80M, 150W, with balun
Morse Decoders
MFJ-461 LCD MORSE CODE
READER
GES08900736
Packet Size Morse Code Reader
The MFJ-490/490X i s a full featured memory keyer with an easy to use menu
dri ven interface. The model MFJ-490 is a keyer and Bencher paddle MFJ564
combination. The MFJ-490X keyer instal ls on your own MFJ-564 or Bencher
type paddle. This uni t has four soft sector stored message memories for a total
of 192 characters. The keyer can repeat messages continuosl y, insert timed
pauses withis messages, insert an auto-i ncrementing serial number, and have
messages call other messages. T he MFJ-490/490X has adjustable control s for
speed and volume on front of the unit. Also, the speed, weight, and sidetone
frequency are adjustable through menu sel ection or paddle command. Other
modes such as Hand Key, Semi -auto, Reverse Paddle, Iambi c On/Off, Iambic
A/B, and Queue, are accessed through menu selection or paddle command.
The MFJ-490/490X has an output confi gurable Direct or Grid-Block output.
1 pc: 6 090 Kč
RoHS
MFJ-490X ELBUG - MEMORY
KEYER
GES08900300
Rel ax and place this tiny pocket si ze MFJ Morse Code / CW Reader near your
receiver's speaker. Then watch Morse code si gnals turn i nto soli d text
messages as they scroll acros an easy-to-read LCD di splay. No cables to
hook-up, no computer, no interface, no other equi pment needed.
1 pc: 2 390 Kč
RoHS
MFJ-462B LCD CW/RTTY/ASCII
/AMTOR DECODER
GES08900737
CW/RTTY/ASCII/AMTOR decoder with LCD display and printer
output.
1 pc: 3 190 Kč
Memory Keyer for traffic, contest, code practice (needs paddle
MFJ564)
The MFJ-490/490X i s a full featured memory keyer with an easy to use menu
dri ven interface. The model MFJ-490 is a keyer and Bencher paddle
combination. The MFJ-490X keyer instal ls on your own MFJ-564 or Bencher
BY-I or BY-II type paddle. This unit has four soft sector stored message
memori es for a total of 192 characters. The keyer can repeat messages
continuosl y, insert timed pauses withis messages, insert an auto-incrementi ng
seri al number, and have messages call other messages. The MFJ-490/490X
has adjustable control s for speed and volume on front of the unit. Also, the
speed, weight, and sidetone frequency are adjustable through menu
selection or paddle command. Other modes such as Hand Key, Semi-auto,
Reverse Paddle, Iambic On/Off, Iambic A/B, and Queue, are accessed
through menu selection or paddle command. The MFJ-490/490X has an
output confi gurable Direct or Grid-Block output.
1 pc: 3 450 Kč
RoHS
MFJ-492 ELBUG - MEMORY KEYER
T iny 5" x 2" x 3" tuner handles full 150 Watts! Covers 80-10 Meters, has tuner
bypass switch, tunes nearl y anythi ng! MFJ brings you the world's small est full
power 150 Watt 80-10 Meter Antenna Tuner - with Balun. Extra wide
matching range lets you tune nearly any antenna. It's no toy -- it's got guts!
Buil t with real air vari able capacitors (600 Volt, 322 pF) and three stacked
powder iron toroids to handle real power -- not just QRP. Bypass swi tch l ets
you bypass tuner when you don't need it. You can use nearly any transceiver
at full power with nearly any coax fed or random wire antenna for portabl e,
home, or mobile operation. It's perfect for compact ri gs like the Icom
IC706MKIIG, Yaesu FT100D, Kenwood TS50, QRP ri gs and other with a
bui lt-i n SWR meter. Operate anywhere, anytime with a quick easy set-up!
T une out SWR on your mobile whi p from insi de your car. Operate in your
apartment with a wall-to-wall antenna or from a motel room with a wi re
dropped from a wi ndow or from a mountai n top with a wi re over a tree l imb.
Great for DXpeditions or field day. Be prepared for emergencies. The
MFJ902H is so small and handy, you'll rely on it wherever you go! It's easy to
pack away in your briefcase, suitcase, backpack, glove compartment, or desk
drawer. It's tiny enough to slide in your back hi p pocket!
RoHS
MFJ-904 ANTENNA TUNER
GES08900973
Travel Tuner 10-80M, 150W, with m eter
1 pc: 5 290 Kč
RoHS
Tuners and Transmatchs
GES08900301
Memory Keyer for traffic, contest and code practice
Tuners upto 300W
MFJ-902B ANTENNA TUNER
GES08902209
Travel Tuner 6-80M, 150W
The MFJ-492 is a full featured memory keyer with an easy to use menu driven
interface. This unit has four soft sector stored message memori es for a total of
192 characters. T he MFJ-492X i s the same keyer but has message memory
expanded to 8 separate 4000 character message memories, gi vi ng the unit
the "X" designation. The keyer can repeat messages continuosly, insert timed
pauses withis messages, insert an auto-i ncrementing serial number, and have
messages call other messages. T he MFJ-492/492X has adjustable control s for
speed and volume on front of the unit. Also, the speed, weight, and sidetone
frequency are adjustable through menu sel ection or paddle command. Other
modes such as Hand Key, Semi -auto, Reverse Paddle, Iambi c On/Off, Iambic
A/B, and Queue, are accessed through menu selection or paddle command.
The MFJ-492/492X has both Direct and Grid-Bl ock outputs and a port for
optional remote control. Passed paddle is MFJ-564 or Bencher BY-I or BY-II.
1 pc: 3 185 Kč
RoHS
MFJ-492X ELBUG - MEMORY
KEYER
GES08900302
Memory Keyer for traffic, contest and code practice
T iny 7" x 2" x 3" tuner handles full 150 Watts! Covers 80-10 Meters, has tuner
bypass switch, tunes nearl y anythi ng! MFJ brings you the world's small est full
power 150 Watt 80-10 Meter Antenna T uner - with SWR/Wattmeter. Extra
wide matching range lets you tune nearly any antenna. It's no toy -- it's got
guts! Buil t with real air vari able capacitors (600 Volt, 322 pF) and three
stacked powder iron toroi ds to handle real power -- not just QRP. Bypass
switch lets you bypass tuner when you don't need it. You can use nearl y any
transceiver at ful l power with nearly any coax fed or random wire antenna for
portable, home, or mobile operati on. It's perfect for compact ri gs l ike the Icom
IC-706MKIIG, Yaesu FT-100D or FT-817 or FT-857 or FT-897, Kenwood
T S-50, QRP ri gs and other with a built-in SWR meter. Operate anywhere,
anyti me with a qui ck easy set-up! Tune out SWR on your mobile whi p from
i nside your car. Operate i n your apartment with a wall -to-wall antenna or from
a motel room with a wire dropped from a window or from a mountain top wi th
a wire over a tree l imb. Great for DXpeditions or field day. Be prepared for
emergencies. The MFJ-904 is so small and handy, you'll rel y on i t wherever
you go! It's easy to pack away in your briefcase, suitcase, backpack, gl ove
compartment, or desk drawer. It's tiny enough to sl ide i n your back hi p pocket!
T he MFJ-904 includes a Cross-Needle SWR/WAttmeter that shows SWR,
forward and reflected power all at a glance. Push button selects
forward/reflected power i n 300/60 and 30/6 Watt ranges.
1 pc: 3 445 Kč
RoHS
Tiny 4" x 2" x 3" tuner handles full 150 Watts! Covers 80-6 Meters, has tuner
bypass switch, tunes nearl y anything! MFJ brings you the world's smal lest full
power 150 Watt 80-6 Meter Antenna Tuner. Extra wide matching range lets
you tune nearly any antenna. It's no toy -- it's got guts! Built with real air
variabl e capaci tors (600 Volt, 322 pF) and three stacked powder iron toroids to
handle real power -- not just QRP. Bypass swi tch lets you bypass tuner when
you don't need it. You can use nearly any transceiver at full power with nearly
any coax fed or random wire antenna for portable, home, or mobile
operation. It's perfect for compact rigs like the Icom IC706MKIIG, Yaesu
FT100D, Kenwood TS50, QRP rigs and other wi th a built-in SWR meter.
Operate anywhere, anytime with a quick easy set-up! T une out SWR on your
mobi le whip from i nside your car. Operate i n your apartment wi th a
wal l-to-wall antenna or from a motel room with a wire dropped from a window
or from a mountain top with a wire over a tree limb. Great for DXpeditions or
field day. Be prepared for emergencies. The MFJ902B is so small and handy,
you'll rel y on i t wherever you go! It's easy to pack away in your briefcase,
suitcase, backpack, glove compartment, or desk drawer. It's ti ny enough to
slide i n your back hip pocket!
MFJ-904H ANTENNA TUNER
GES08900975
Travel Tuner 10-80M, 150W, with m eter and balun
1 pc: 2 920 Kč
RoHS
1 pc: 3 580 Kč
RoHS
T iny 7" x 2" x 3" tuner handles full 150 Watts! Covers 80-10 Meters, has tuner
bypass switch, tunes nearl y anythi ng! MFJ brings you the world's small est full
power 150 Watt 80-10 Meter Antenna Tuner - with Balun and
SWR/Wattmeter. Extra wide matchi ng range lets you tune nearly any
antenna. It's no toy -- it's got guts! Built with real air variable capaci tors (600
Vol t, 322 pF) and three stacked powder iron toroi ds to handl e real power -- not
j ust QRP. Bypass switch l ets you bypass tuner when you don't need i t. You can
use nearl y any transceiver at ful l power with nearly any coax fed or random
wire antenna for portable, home, or mobil e operation. It's perfect for compact
rigs li ke the Icom IC706MKIIG, Yaesu FT100D or FT 817 or FT857 or FT 897,
Kenwood TS50, QRP ri gs and other with a built-in SWR meter. Operate
anywhere, anytime with a quick easy set-up! Tune out SWR on your mobi le
whip from i nside your car. Operate in your apartment wi th a wal l-to-wall
antenna or from a motel room with a wire dropped from a window or from a
mountai n top wi th a wire over a tree li mb. Great for DXpedi tions or field day.
Be prepared for emergencies. The MFJ904H i s so smal l and handy, you'll rel y
on it wherever you go! It's easy to pack away i n your briefcase, suitcase,
backpack, gl ove compartment, or desk drawer. It's tiny enough to slide in your
back hip pocket! T he MFJ-904H incl udes a Cross-Needle SWR/WAttmeter and
4 : 1 bal un for balanced l ines and random wire. Cross-Needle meter shows
SWR, forward and refl ected power all at a glance. Push button selects
forward/reflected power i n 300/60 and 30/6 Watt ranges.
1 pc: 3 990 Kč
RoHS
MFJ-971 ANTENNA TUNER
GES08901035
MFJ compact minituner 1.8-30MHz; max.200W PEP(100W CW);
153x153x64mm
The MFJ-971 is a compact QRP portable minituner esti mated for 50 Ohm
transmitter or TCVR with 200W PEP (100W CW) output. T uner has a special
user-selectabl e 6 Watt range for QRP operation (0-6W Forward Power, 0-1.2W
Reflected Power). Tuner covers 1.8 to 30MHz. It provides a convenient crossneedle type SWR/Wattmeter. Power range is 0-300W for Forward Power
(switchable to 0-30W) and 0-60W for Reflected power. T he T-Match tuner
tunes allmost any coax, wire, or balanced-feed type antenna. A 4:1 toroid
balun is built in for balanced li ne.
1 pc: 3 445 Kč
RoHS
MFJ-941E ANTENNA TUNER
GES08901021
Versa II Tuner 1.8-30 MHz 300/30W PEP, Croos-Needle Meter,
Balun 4:1
VC-300DLP ANTENNA TUNER
GES08901604
300W HF Tuner 1.8 - 30MHz
MFJ-927 AUTOMATICAL ANTENNA
TUNER
GES08901825
Autom atic tuner 1.8-30MHz; 200W SSB/CW; 6-1600Ohm.; weather
proof
The VC-300DLP Antenna Tuner optimizes the performance of your antenna
and transmitter, receiver, or transceiver by providi ng adj ustabl e impedance
matchi ng. The Cross-Needle meter shows SWR, forward and reflected power at a glance. It reads forward/refl ected power in 300/60 and 30/6 Watt ranges.
1 pc: 4 770 Kč
RoHS
MFJ-928 AUTOMATICAL ANTENNA
TUNER
GES08901824
Automatic tuner 1.8-30MHz; 200W SSB/CW; 6-1600Ohm.;
165x70x191mm ; 1.2kg
T his rugged Remote Intell iTuner Automatic Antenna T uner automaticall y
matches antennas from 6 to 1600 Ohms impedance (SWR up to 32:1) and
handl es 200 Watts SSB/CW. Tune in l ess than 15 seconds, usually less than 5
seconds. Over 20000 non-vol ati le memories for tuner settings. Highly efficient
switchi ng L-network matchi ng ci rcuit. 1.8 to 30 MHz continuous frequency
coverage. Has SO-239 coax fed antenna connector and antenna connector
for random wire or si ngle wire antennas. Has SO-239 coax fed connector wi th
bui lt-i n bi as tee for transmitter. At transmitter si de the bias tee type MFJ4116
GES 089 018 66 with external 12V DC/1Amax. power suppl y (MW 9112GS
GES 075 066 49 or similar from GES-ELECTRONICS) i s required. T uner
MFJ927 i s perfect for smal l T CVRs with output power up to 100W (FT 857,
FT897 and others).
1 pc: 6 890 Kč
RoHS
MFJ-933 ANTENNA TUNER
GES08901066
Hom e Station LoopTuner 80-10M. Same as MFJ-935B less RF
current meter.
Thi s uni versal tuner match virtual ly any transmitter to any antenna, includi ng
dipol es, inverted-vees, vertical s, mobil e whi ps, beams, random wires and
others fed by coax lines, balanced lines or single wire. MFJ's l ighted CrossNeedl e meter shows SWR, rorward and reflected power all at a gl ance in
300/60 and 30/6 Watt ranges, 8 positi on antenna switch lets you sel ect 2 coax
lines, random wire/balanced line or dummy load. Has 4 : 1 balun, 1000 Volt
capacitors.
1 pc: 3 980 Kč
Thi s Automatic Antenna Tuner automati cally matches antennas from 6 to
1600 Ohms impedance (SWR up to 32:1) and handles 200 Watts SSB/CW.
Tune i n l ess than 15 seconds, usuall y less than 5 seconds. Over 20000
non-volatile memories for tuner settings. Highl y efficient switching L-network
matchi ng circuit. 1.8 to 30 MHz continuous frequency coverage. Has SO-239
coax fed antenna connector, and antenna connector for random wi re or single
wire antennas. Has SO-239 coax fed connector for transmitter. Built-in bias
tee (similar to MFJ4116 GES 089 018 66 ) for remote power suppl y. An
external 12V DC/1Amax. power supply (MW9112GS GES 075 066 49 or
similar from GES-ELECTRONICS) and (i f needed) the MFJ4116
GES 089 018 66 bias tee is required. Tuner i s superb for small transceivers
with output power up to 100W (FT857, FT 897 and others)
RoHS
MFJ-945E ANTENNA TUNER +
SWR/WATTMETER
GES08901026
Mobile Tuner with Cross-Needle Meter, 1.8-60MHz, 300/30W,
203x51x152mm
1 pc: 5 290 Kč
RoHS
MFJ-929 AUTOMATICAL ANTENNA
TUNER
GES08901823
Automatic tuner 1.8-30MHz; 200W SSB/CW; 6-1600Ohm.;
165x70x191mm ; 1.1kg
Drape a wi re around a bookcase and attach both ends to this new MFJ-933
Small High Efficiency Loop T uner. It instantly turns into a small, high
effi ci ency multi-band transmitting loop antenna! You can operate 3.5 to 30
MHz with a full 150 Watts. No ground, radial s or counterpoises needed. A
13-ft wi re formed into a loop operates 30-20 Meters (4-ft for 17-10M; 7-ft for
20-15M; 28-ft for 40M). You can tune any shape l oop -- circl e, square,
rectangle, any odd shape. A quarter wavelength wire shaped as a circl e is the
most efficient. A fixed wi re l ength covers about 1.5 to 1 frequency range (i.e.
28-18 or 10-7 MHz, etc.). Exact frequency coverage depends on wire length,
l oop shape and environment.
1 pc: 5 035 Kč
RoHS
MFJ-935B ANTENNA TUNER
GES08902088
Portable/home LoopTuner 5.3-29.7MHz/150W. Same as MFJ933,
with RF current meter
Don't leave home without this mobil e tuner. The Cross-Needl e meter shows
SWR, forward and refl ected power - at a glance. It reads forward/reflected
power in 300/60 and 30/6 Watt ranges. A mobi le mount, MFJ-20 (
GES 089 005 66 ) can be purchased as well.
1 pc: 3 695 Kč
RoHS
MFJ-948 ANTENNA TUNER
GES08901069
Antenna 1.8-30MHz 300W tuner, without Dummy Load
MFJ-929 automatical ly matches antennas from 6 to 1600 Ohms impedance
(SWR up to 32:1) and handles 200 Watts SSB/CW. Tune in less than 15
seconds, usual ly less than 5 seconds. Over 20000 non-vol ati le memori es for
tuner settings. Four memory banks per antenna with over 2500 memories per
bank. Highl y efficient switching L-network matching ci rcuit. 1.8 to 30 MHz
continuous frequency coverage. Adjustable target SWR 1.0 to 2.0. Adjustable
SWR threshol d 0.5 to 1.5. Lighted cross-needl e SWR/wattmeter. Mul tifuncti on
backl it LCD displ ay with contrast control. Built-in frequency counter. Numeric
readi ngs for SWR, forward and reflected power. Bar meters for SWR, forward
and reflected power. Aural SWR meter wi th volume control . Two SO-239 coax
fed antenna connectors. Connector for random wire or single wire antennas.
Bui lt-i n bias tee for remote power supply. Optional connector for radio
interface for compatible radios. Power supplying i s di rect or remotly via
coaxial cable from transmitter side using optional MJF4116 (
GES 089 018 66 ) bi as tee. External 12V DC/1A max. power supply i s
requi red (MW9112GS GES 089 018 66 or similar from GES-ELECTRONICS).
Thi s tuner is superb for all 50-100W T CVRs (FT 857, FT897 or simil ar).
1 pc: 6 090 Kč
RoHS
Drape a wire around a bookcase and attach both ends to thi s new MFJ935B
Small High Effi ci ency Loop Tuner! It i nstantly turns into a small, high
effi ci ency multi-band transmitting loop antenna! Same as MFJ933 but wi th
bui ld-in RF current meter. Smal l Physi cal Profi le 159x242x134mm. You can
operate 5.3 to 29.7 MHz with a full 150 Watts. No ground, radial s or
counterpoises needed. A 13-ft wire formed i nto a l oop operates 30-20 Meters
(4-ft for 17-10M; 7-ft for 20-15M; 28-ft for 40M). You can tune any shape loop
-- circle, square, rectangl e, any odd shape. A quarter wavelength wire shaped
as a circle is the most efficient. A fi xed wire length covers about 1.5 to 1
frequency range (i.e. 28-18 or 10-7 MHz, etc.). Exact frequency coverage
depends on wire l ength, l oop shape and environment.
1 pc: 5 570 Kč
RoHS
1 pc: 4 495 Kč
RoHS
MFJ-949E ANTENNA TUNER w.
DUMMY LOAD
GES08901070
Antenna 1.8-30 MHz 300W tuner, built in Dummy Load
300W/30s ec.max
1 pc: 4 995 Kč
RoHS
MFJ-936B ANTENNA TUNER
GES08902089
DeLuxe Portable/home LoopTuner 5.3-29.7MHz / 150W.
MFJ-993B AUTOMATICAL
ANTENNA TUNER
GES08901784
MFJ-5124A INTERFACE ALINCO
GES08900809
Interface Cable MFJ991, MFJ993, MFJ994 / ALINCO
Automatic tuner 1.8-30MHz; 300W or 150W SSB/CW;
257x71x234mm ; 1.8kg
Thi s is the DeLuxe version of MFJ935B with bui lt-i n cross-needle
SWR/Wattmeter. Small physical profi le 261x242x134mm. Drape a wire
around a bookcase and attach both ends to this new MFJ935B Small Hi gh
Effi ci ency Loop Tuner! It instantly turns into a small, hi gh efficiency
multi -band transmi tting loop antenna! You can operate 5.3 to 29.7 MHz with
a full 150 Watts. No ground, radial s or counterpoises needed. A 13-ft wire
formed into a loop operates 30-20 Meters (4-ft for 17-10M; 7-ft for 20-15M;
28-ft for 40M). You can tune any shape loop -- circle, square, rectangl e, any
odd shape. A quarter wavelength wire shaped as a ci rcle is the most efficient.
A fixed wire l ength covers about 1.5 to 1 frequency range (i.e. 28-18 or 10-7
MHz, etc.). Exact frequency coverage depends on wire l ength, loop shape
and environment.
1 pc: 6 890 Kč
RoHS
MFJ-934 ANTENNA TUNER
GES08901009
Antenna Tuner 1.8-30 MHz 300W HF Artificial Ground / Term ination
Automaticall y matches antennas from 6 to 1600 Ohms impedance and
handles 300 Watts SSB/CW or matches 6 to 3200 Ohms and handless 150
Watts SSB/CW. Tune in l ess than 15 seconds, usual ly less than 5 seconds.
Over 20000 non-vol ati le memories for tuner setti ngs. Highly efficient
switching L-network matching circui t. 1.8 to 30 MHz continuous frequency
coverage. Adjustable target SWR 1.0 to 2.0. Adjustable SWR threshold 0.5 to
1.5. Lighted cross-needle SWR/wattmeter with high, l ow, and auto range
options. Multifunction backlit LCD displ ay with contrast control . Built-in
frequency counter. Numeric readings for SWR, forward and reflected power.
Bar meters for SWR, forward and reflected power. Aural SWR meter with
volume control . Two SO-239 coax fed antenna connectors. Connector for
random wi re or si ngle wi re antennas. Built-in 4:1 current balun for balanced
line antennas. Optional remote control MFJ-993RC . Optional radio interface
MFJ-5124 for compati ble radios. MFJ-993B tuner is perfect wi th any 100W
TCVR, works fine with FT857 , FT897 and others. External 12V DC/1Amax.
power supply i s required (see www.ges.cz/en/accumulators-batteri es-resources
/power-supplies/general-purpose-mai ns-adapters/universal-mains-dc-adaptersstabili zed/SITN4.html
1 pc: 530 Kč
RoHS
MFJ-5124K INTERFACE KENWOOD
GES08901062
Interface MFJ991, MFJ993, MFJ994 / KENWOOD
1 pc: 7 150 Kč
RoHS
MFJ-994B AUTOMATICAL
ANTENNA TUNER
GES08901785
Automatic tuner 1.8-30MHz; 600W or 300W SSB/CW;
257x71x234mm ; 1.7kg
1 pc: 1 590 Kč
RoHS
MFJ-5124Y INTERFACE YAESU
GES08901063
Interface MFJ991, MFJ993, MFJ994 / YAESU FT100, FT857, FT897
1 pc: 1 590 Kč
The MFJ-934 is a 300 watt (175 watts on 160 meters) RF output power
antenna tuner and arti ficial ground system that wil l match any transmitter or
transcei ver to virtually any antenna. A special circui t in this tuner cancels the
reactance of a ground lead or counterpoise, and reduces problems caused by
RF "i n the shack". Forward power, reflected power, ground current, and SWR
can be read on the wattmeter's ill uminated cross-needle meter. The MFJ-934
tuner secti on uses a "T" network and covers al l bands between 160 and 10
meters. T his network will work wi th dipol es, inverted-vees, verticals, mobile
whi ps, beams, random wi res, and many other antennas. The MFJ-934 has
rear panel connectors for coaxial, single wire or two wire feedli nes. A built-in
4:1 bal un allows the use of balanced open wire, twi nlead, or twi n-axial
feedl ines. An illuminated cross-needle meter measures the FORWARD and
REFLECTED power, ground current, and the SWR. The meter's full scale
forward and refl ected power range is controlled by the right METER RANGE
switch. If your transmitter has more than 30 watts of output power, set thi s
switch to the 300W (button i n). If your transmitter has less than 30 watts of
output, use the 30W swi tch position (button out). Forward power is di splayed
on the left-hand FORWARD meter scale when the FORWARD CURRENT
button is out. Read directly from the scal e i n the 300 watt positi on. In the
30W positi on the forward power scale must be di vi ded by 10. Refl ected power
is read on the right-hand REFLECTED meter scale. This scale indicates 60
watts ful l scale when the 300W power sensitivity is sel ected, and 6 watts when
the 30W forward power range i s selected. This scale must be di vi ded by 10
when usi ng the 30W power range positi on. The most accurate power readi ngs
occur in the upper half of the meter scal es. To accurately measure power with
a less than perfect match, the refl ected power should be subtracted from the
forward power readi ng.
Automaticall y matches antennas from 8 to 800 Ohms impedance and
handles 600 Watts PEP SSB/300W CW. T une in less than 15 seconds, usual ly
less than 5 seconds. Over 10000 non-volatile memories for tuner settings.
Highly efficient switching L-network matching circuit. 1.8 to 30 MHz
continuous frequency coverage. Adjustable target SWR 1.0 to 2.0. Adjustable
SWR threshold 0.5 to 1.5. Lighted cross-needle SWR/wattmeter with high,
low, and auto range opti ons. Multifunction backl it LCD display wi th contrast
control . Bui lt-i n frequency counter. Numeri c readings for SWR, forward and
reflected power. Bar meters for SWR, forward and reflected power. SO-239
coax fed antenna connector. Connector for random wire or si ngle wire
antennas. Optional remote control. Optional radio i nterface for compatible
radios. External 12V DC/1A max. power suppl y i s required (see www.ges.cz/en
/accumulators-batteries-resources/power-suppli es/general-purpose-mainsadapters/universal-mains-dc-adapters-stabili zed/SITN4.html
1 pc: 9 540 Kč
RoHS
MFJ-4116 BIAS TEE
GES08901866
RoHS
MFJ-5124Y2 INTERFACE YAESU
GES08901741
Interface MFJ991, MFJ993, MFJ994 / YAESU FT847
1 pc: 1 590 Kč
RoHS
Tuners over 300W
MFJ-962D ANTENNA TUNER ROLLER
GES08901071
Roller Ant.Tuner 160-10m (800W CW,500W CW/160m ), Watt/SWR
Meter, Balun
Bias Tee 1A/1-50VDC/1-60MHz for Coax Cable 50 Ohm .
70x64x32mm.
1 pc: 5 570 Kč
RoHS
MFJ-991B AUTOMATICAL
ANTENNA TUNER
It's perfect for Ameritron AL-811 power amplifiers.
GES08901783
Automatic tuner 1.8-30MHz; 300W or 150W CW/SSB;
257x71x234mm ; 1.7kg
Ideal for running coax to distant devi ces allowing then to be placed anywhere
regardless of power avai labili ty. Perfect for automatical tuners MFJ927 (
GES 089 018 25 ) or MFJ928 ( GES 089 018 24 ) or MFJ929 (
GES 089 018 23 ) or other remote devices.
1 pc: 795 Kč
RoHS
MFJ-993RC REMOTE CONTROLL f.
ANTENNA TUNER
GES08901046
1 pc: 8 485 Kč
RoHS
ATR-20X ANTENNA TUNER ROLLER
GES08901102
Antenna tuner w.roller, 1.2kW SSB/600W CW; 1.8-30MHz;
33x12x43cm; cross-needle meter
Remote Control for MFJ991, MFJ991B, MFJ993, MFJ993B,
MFJ994, MFJ994B
Perfect for small 100W T CVRs ( FT857 , FT897 ? and others). Automatical ly
matches antennas from 6 to 1600 Ohms i mpedance and handles 300 Watts
SSB/CW or matches 6 to 3200 Ohms and handless 150 Watts SSB/CW. Tune
in less than 15 seconds, usually less than 5 seconds. Over 10000 non-volatile
memori es for tuner setti ngs. Hi ghly efficient swi tching L-network matchi ng
ci rcuit. 1.8 to 30 MHz continuous frequency coverage. Adjustable target SWR
1.0 to 2.0. Adjustable SWR threshold 0.5 to 1.5. Li ghted cross-needle
SWR/wattmeter with hi gh, low, and auto range options. Multi function backlit
LCD displ ay with contrast control . Built-in frequency counter. Numeric
readi ngs for SWR, forward and reflected power. Bar meters for SWR, forward
and reflected power. SO-239 coax fed antenna connector. Connector for
random wi re or single wi re antennas. Opti onal remote control. Opti onal radio
interface for compatible radios. External 12V DC/1A max. power suppl y i s
requi red - see our www.ges.cz/en/accumulators-batteries-resources/powersuppli es/general-purpose-mains-adapters/universal -mains-dc-adaptersstabili zed/SITN4.html
1 pc: 6 090 Kč
RoHS
Designed for PA AMERITRON series AL-811, AL-811H, AL-80B, ALS-500M,
ALS-600 and similar PA. Powered wi th i nternal 9V battery or with 12VDC
from external 230VAC power supply.
1 pc: 12 180 Kč
RoHS
1 pc: 1 060 Kč
RoHS
MFJ-976 ANTENNA TUNER
GES08901072
Fully Balanced Tuner,1.5kW PEP
SSB/CW,1.8-30MHz,coax.input,symetr.+coax.output
1 pc: 13 250 Kč
RoHS
GES08901602
Desi gned for PA AMERITRON or any other PA with maximal output power
1500W CW. Powered with internal 9V battery or wi th 12VDC from external
230VAC power supply. - Handles 1500 watts carrier - Super hi gh Current edge
wound si lver pl ated Roller Inductor - 500 pf tuning capaci tors wi th 6:1 vernier
reducti on drives - 3 core choke bal un - 6 posi tion antenna switch True peak
readi ng meter Ameritrons ATR-30X true Legal Limit roll er inductor antenna
tuner is ham radios toughest! Itl l handl e 1500 Watts continuous carri er output
on al l modes and al l HF bands into most antennas -- even on 160 meters
where most antenna tuners fail. Its perfect for Ameritrons most powerful
ampl ifiers where the ATR-30X j ust loafs. All band coverage l ets you operate
1.8 - 30 MHz incl uding al l MARS and WARC bands. Super High Current
Rol ler Inductor Youll see Ameritrons new super hi gh current air core rol ler
inductor. Its edge wound from a thick solid copper strip and silver plated. Thi s
produces a large surface area and a massive conductor. It can carry huge
ci rculating RF currents and wi thstand tremendous heat thatll melt or burn
ordinary roll er inductors. A gear dri ven turns counters and crank knob gives
you precise inductance control. Two 500 pf T uning Capacitors Two 500 pf -the highest of any antenna tuner -- variable transmitti ng capacitors give you
no-arc wide range impedance matching for true hi gh power performance. 6:1
vernier reduction drives makes capacitor tuning smooth and easy. Super
Bal un, 6-posi tion Antenna Switch Super heavy duty three core choke bal un
lets you match virtually any balanced feedl ine antenna wi thout core
saturation. A 6 positi on antenna switch lets you select your desired operati ng
antenna. Read True Peak power Ameri trons active electronic true peak
readi ng meter accurately reads forward and reflected power and SWR
simultaneously on a lighted Cross-Needle meter. Roomy Cabinet mai ntains
High-Q Roomy extra-strong .080 inch thi nk al uminum cabinet gives highest
efficiency and l owest l oss.
1 pc: 15 890 Kč
Roller tuner 2kW SSB/1kW CW, 1.8-30MHz, 4:1balun, tune bar,
140x318x305m m, 4.5kg
1 pc: 12 720 Kč
RoHS
GES08901104
Antenna tuner, roller inductor, 3kW SSB/1.5kW CW, 1.8-30MHz,
cross-needle meter
The MFJ-976 i s a 1500 Watt full legal limit full y bal anced antenna tuner.
MFJ-976 has a coaxial input and ballanced pl us coaxial output. You get
superb bal ance, very wide matchi ng ranges (12-2000 Ohms) and conti nuous
1.8-30 MHz coverage includi ng all WARC bands! It handl es a ful l 1500 Watts
SSB and CW. You can tune any balanced l ines i ncluding 600 Ohm open wire
line, 450/300 Ohm ladder lines, 300/72 Ohm twin lead -- shielded or
unshielded. T he MFJ-976 also tunes random wires and coax-fed antennas.
MFJ's fully bal anced extremely wide-range T-network gives you simple, fast
three knob tuning. No complicated switchi ng between high and low
impedance and switchi ng i n additional capacitance of L-networks. Four
separate 500 pF in two gangs gives you a total of 2000 pF for highly efficient
low loss separation on 160 Meters. You get excel lent 10 Meter performance
because of MFJ's low mi nimum capacitance and exclusi ve Self-Resonance
Kill er hi gh-Q AirCore roller inductor with si lver pl ated contacts. The MFJ-976
1500 Watt Fully Balanced Antenna T uner has a heavy duty 1:1 current bal un
that gives you superb balance and stays cool even at 1.5 kW. True acti ve peak
readi ng l ighted Cross-Needle SWR/Wattmeter lets you read SWR, true peak or
average forward and reflected power al l at a glance on 300/3000 Watt
ranges. T he MFJ-976 unit measures 12W x 6H x 15-3/4D inches.
HFT-1500 ANTENNA TUNER ROLLER
ATR-30X ANTENNA TUNER ROLLER
RoHS
MFJ-998 AUTOMATICAL ANTENNA
TUNER
GES08902184
Autom atic Legal Limit IntelliTuner 1.8-30MHz; 1500W SSB/CW
MFJ 1500 Watt Legal Limit Intelli Tuner Full 1500 watts SSB/CW…Digital &
Analog SWR/WattMeter . . . Al l features of MFJ Intel liTuners-- Ultra-fast, Safe
Automati c Tuni ng . . . Wide Tuni ng Range (12-1600 Ohms from 1.8 to 30
MHz ) . . . Radio Interfaces . . . Built-in Antenna Switch for two coax/l ong wi re
. . . Automati c Bypass protects your amplifi er . . . Field Upgradeable Software
. . . Very Compact! T he MFJ-998 Full Legal Limit 1500 Watt Intel lituner takes
you to the final level in automati c antenna tuners. Wi th a capabili ty of 1500
watts SSB and CW, coupled with automati c tuning, your high-power station
can now operate essential ly hands-free even when frequency and band
changes are made. Fast Automatic Tuni ng The MFJ-998 instantly matches
i mpedances from 12-1600 ohms using MFJ's exclusive IntelliT une,
Adapti veSearch
and
InstantRecall
al gorithms wi th
over 20,000
Virtual Antenna Memories. When you key your transmitter, MFJ's InstantRecall
checks to see if that frequency has been used before. If so, tuning is
i nstantaneous. If not, MFJ's Intel liTune algori thm (based on MFJ's efficient
SWR Analyzer technology) measures the impedance, snaps the necessary
components i n place, and then fine-tunes the SWR. If the antenna
i mpedance is outside the tuner's measurement range, MFJ's Adaptive Search
algori thm measures the frequency and determi nes only rel evant component
values -- which are then searched for fast tuni ng. Safe Automati c Tuning and
Amplifier Protection The MFJ-998 includes MFJ’s Ampl ifier Bypass Control -an MFJ exclusi ve feature! When used wi th a transceiver interface cabl e,
tuning is safe and "stupidproof"! When a tuni ng cycle is ini tiated, the
MFJ-998 first bypasses any in-line ampl ifier. Next, the MFJ-998 ini tiates a
l ow-power CW tuni ng carrier from your transceiver. When tuning is complete,
the MFJ-998 reverts your transceiver to i ts prior power and mode, and
re-enabl es the ampl ifier. T his enti re cycle typically takes l ess than a second!
Finall y, i f the MFJ-998 cannot find a match better than a preset amplifi er
SWR trip-point, the ampl ifier stays bypassed to provide automatic SWR
protecti on for your ampli fier -- another MFJ excl usive! Anal og SWR/Wattmeter
A l arge analog Cross-Needle SWR/Watt-meter displays sel ectable 300/60 watt
or 3000/600 watt forward/reflected full -scale ranges. You can even select
automatic power ranging -- the best power range is automatical ly sel ected for
you. Digital LCD SWR/Wattmeter A two-line, 16-character backlit LCD meter
displays SWR, forward/reflected power, frequency, antenna selected, an
auto-ranging bargraph power indi cation, and much more. You can even read
the final matching inductor and capacitor values should you want to bui ld
your own fixed matching network. Simpl e menus determi ne displayed
i nformation - no complex button combi nations to remember! MFJ
Virtual Antenna Memory MFJ new VirtualAntenna Memory system gi ves you 4
antenna memory banks for each of 2 swi tchable antenna connectors. Select
up to 4 antennas on each antenna connector. Each antenna has 2500
memories, 20,000 total. Has two coax connectors and a bi nding post for
end-fed l ong wire antennas. Download and Upgrade Remotely Field
upgradeable fi rmware vi a the seri al port -- download and upgrade your
MFJ-998 as new features are introduced! Pl us Much More! Built-in radio
i nterface provides control of most amateur transceivers. Automati c bypassing
when excessive tuning power or power in excess of 1500 watts is applied. Use
bal anced line antennas with external MFJ-912, 1.5 kW 4:1 balun. MFJ-998 is
the smallest ful l legal -limit auto-tuner in the world! 13Wx4Hx15D i nches fits
easi ly into your ham station. Weighs just 8 pounds -- great portabi lity!
External 12V DC/1A max. power suppl y is required (see www.ges.cz/en
/accumul ators-batteries-resources/power-supplies/general-purpose-mainsadapters/universal-mains-dc-adapters-stabilized/SITN4.html Pre-wired Rig
Interface Cables for MFJ-929/998 These cables work with the following MFJ
Automati c tuners: MFJ-929, MFJ-928, MFJ-925, and the MFJ-998.
MFJ-5114K Prewired Rig Interface cable for Kenwood and compatibl es.
MFJ-5114I. Prewired Rig Interface cabl e for Icom and compatibl es.
MFJ-5114Y. Prewi red Ri g Interface cable for Yaesu and compatibl es.
MFJ-5114Y3. Prewired MFJ-929 to FT-1000MP, FT-9000 Yaesu ri gs.
MFJ-5114Y4. Prewi red MFJ-929 to FT2000 Yaesu rigs.
1 pc: 18 550 Kč
RoHS
Copyright 2014 © GES-ELECTRONICS, a.s. | tel. 377 373 111 | fax 377 373 999 | e-mail [email protected] | www.ges.cz

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project