SOLE LCB Light Commercial Upright Cycle Model #16867379

SOLE LCB Light Commercial Upright Cycle Model #16867379
Z100 / Z300
Z500
Z700
Model : 16867379
OWNERÊS MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING
YOUR NEW INDOOR CYCLE
TABLE OF CONTENTS
Product Registration
3
Important Safety Instructions
4
Important Operation Instructions
4
Transport Instructions
4
Assembly Instructions
6
Fitness Bike Features
9
Operation of Your New Fitness Bike
10
Programmable Features
13
Using Heart Rate Monitor
20
General Maintenance
22
Exploded View Diagram
23
Parts List
24
Manufacturer's limited warranty
26
ATTENTION
THIS FITNESS BIKE IS INTENDED FOR RESIDENTIAL USE ONLY AND IS
WARRANTED FOR THE APPLICATION. ANY OTHER APPLICATION VOIDS THIS
WARRANTY IN ITS ENTIRETY.
Dyaco Canada Inc. 2013
2
[email protected]
CONGRATULATIONS ON YOUR NEW UPRIGHT AND WELCOME TO THE SOLE FAMILY!
Thank you for your purchase of this quality Sole Upright from Dyaco Canada Inc. Your new
Upright has been manufactured by one of the leading fitness manufacturers in the world and
is backed by one of the most comprehensive warranties available. Dyaco Canada Inc. will do
all we can to make your ownership experience as pleasant as possible for many years to
come.
If you have any questions about your new Sole product or questions about the warranty
contact Dyaco Canada Inc. at 1-888-707-1880.
Please take a moment at this time to record below the name of the dealer, their telephone
number, and the date of purchase for easy contact in the future. We appreciate your
confidence in SOLE and we will always remember that you are the reason that we are in
business. Please complete and mail your registration card today and enjoy your new Upright.
Yours in Health,
Dyaco Canada Inc.
Name of Dealer
Telephone Number of Dealer
Purchase Date
PRODUCT REGISTRATION
RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this fitness product in
the space provided below.
Serial Number
Dyaco Canada Inc. 2013
3
[email protected]
IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this appliance.
Do not operate fitness bike on deeply padded, plush or shag carpet. Damage to
both carpet and fitness bike may result.
Keep children away from the fitness bike. There are obvious pinch points and other
caution areas that can cause harm.
Keep hands away from all moving parts.
Never drop or insert any object into any openings.
Do not use outdoors.
Do not attempt to use your fitness bike for any purpose other than for the purpose it
is intended.
The hand pulse sensors are not medical devices. Various factors, including the
user’s movement, may affect the accuracy of heart rate readings. The pulse sensors
are intended only as exercise aids in determining heart rate trends in general.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable
for use on your fitness bike. Quality athletic shoes are recommended to avoid leg
fatigue or injury.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
IMPORTANT OPERATION INSTRUCTIONS
NEVER expose this fitness bike to rain or moisture. This product is NOT designed
for use outdoors, near a pool or spa, or in any other high humidity environment. The
operating temperature specification is 40 to 120 degrees Fahrenheit, and humidity
is 95% non-condensing (no water drops forming on surfaces).
NEVER operate this fitness bike without reading and completely understanding the
results of any operational change you request from the computer.
Understand that changes in resistance do not occur immediately. Set your desired
resistance on the computer console and release the adjustment key. The computer
will obey the command gradually.
Use caution while participating in other activities while pedaling on your fitness bike;
such as watching television, reading, etc. These distractions may result in serious
injury.
Do not use excessive pressure on console control keys. They are precision set to
function properly with little finger pressure. If you feel the buttons are not functioning
properly with normal pressure contact your SOLE dealer.
TRANSPORT INSTRUCTIONS
The fitness bike is equippped with two transport wheels which are engaged when the rear of
the fitness bike is lifted.
Dyaco Canada Inc. 2013
4
[email protected]
ASSEMBLY PACK CHECKLIST
1 HARDWARE STEP 1
#50. 3/8” x 2-1/4”
Hex Head Bolt (2 pcs)
#58. M5 x 12mm
Phillips Head Screw (2 pcs)
#71. 3/8” x 25mm x 2T
Flat Washer (2 pcs)
2 HARDWARE STEP 2
#51. 5/16” x 5/8”
Hex Head Bolt (7 pcs)
#72. 5/16” x 18mm x 1.5T
Flat Washer (6 pcs)
#99. 5/16” x 19 x 1.5T
Curved Washer (1 pc)
3 HARDWARE STEP 3
#51. 5/16” x 5/8”
Hex Head Bolt (2 pcs)
4
#72. 5/16” x 18mm x 1.5T
Flat Washer (2 pcs)
#103. 5/16” x 1.5T
Split Washer (2 pcs)
HARDWARE STEP 4
#58. M5 x 12mm
Phillips Head Screw (6 pcs)
Dyaco Canada Inc. 2013
5
[email protected]
ASSEMBLY TOOLS
#93. Phillips Head Screwdriver
#92. 13/15mm Wrench
#100. 12/14mm Wrench
ASSEMBLY INSTRUCTIONS
PRE-ASSEMBLY
1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of
box. Lift Box over the unit and unpack.
2. Carefully remove all parts from carton and inspect for any damage or
missing parts. If damaged parts are found, or parts are missing,
contact your dealer immediately.
3. Locate the hardware package. Remove the tools first. Remove the
hardware for each step as needed to avoid confusion. The numbers
in the instructions that are in parenthesis (#) are the item number
from the assembly drawing for reference.
Dyaco Canada Inc. 2013
6
[email protected]
1 REAR STABILIZE
HARDWARE STEP 1
#50. 3/8” x 2-1/4”
Hex Head Bolt (2 pcs)
#58. M5 x 12mm
Phillips Head Screw
(2 pcs)
#71. 3/8” x 25 x 2T
Flat Washer (2 pcs)
1. Attach the Rear Stabilizer Cover (41) to the Rear Stabilizer (5) with two
2.
Phillips Head Screws (58). Tighten with the Phillips Head Screw Driver
(93).
Attach the Rear Stabilizer (5) to the Main Frame (1) by sliding two Flat
Washers (71) onto two Hex Head Bolts (50); insert the bolts through the
Rear Stabilizer Attachment Plate (131), then into the Rear Stabilizer.
Tighten using the 12/14 mm Wrench (100).
2 CONSOLE MAST
HARDWARE STEP 2
#51. 5/16” x 5/8”
Hex Head Bolt (7 pcs)
#72. 5/16” x 18 x 1.5T
Flat Washer (6 pcs)
#99. 5/16” x 19 x 1.5T
Curved Washer
(1 pcs)
1.
2.
Unravel the Computer (29) and Ground (32) cables, then pull the twist
tie wire through the Console Mast Cover (38) (see illustration for the
correct orientation of the cover)and the Console Mast (2) until the
cable connector comes out the top opening of the console mast
Attach the Console Mast (2) onto the Main Frame (1) with the seven
Hex Head Bolts (51). Place six Flat Washers (72) on the side bolts
and one Curved Washer (99) on the front bolt. Tighten using the
12/14mm Wrench (100).
Dyaco Canada Inc. 2013
7
[email protected]
3 HANDLE BAR
HARDWARE STEP 3
#51. 5/16” x 5/8”
Hex Head Bolt (2 pcs)
#72. 5/16” x 18 x 1.5T
Flat Washer (2 pcs)
#103. 5/16” x 1.5T Split
Washer (2 pcs)
1.
2.
3.
Remove the plastic tie that is holding the plastic cover on the center of
the handlebars.
Feed the Hand Pulse Cables (26 & 28) through the opening of the
handlebar mounting bracket (front of 2) and console mounting bracket
(back of 2) .
Attach the Handle Bar (3) to the Front Console Mast (2) with the two
Hex Head bolts (51), two Flat Washers (72) and two Split Washers
(103). Tighten using the 12/14mm Wrench (100).
4 PLASTIC PARTS
1.
2.
3.
4.
5.
HARDWARE STEP 4
See page 9 for illustration
Untie the twist tie that holds the two cables together and discard it.
Insert theComputer Cable (29), Ground Cable (32), and two Hand pulse
cables (26 & 28) into the connectors in the back of the Console (34).
Attach the Console (34) onto the Console Mast (2) with four Phillips
Head Screws (58). Tighten using the Phillips Head Screw Driver (93).
Attach the Front Stabilizer Cover (40) to the Main Frame (1) with two
Phillips Head Screws (58). Tighten with the Phillips Head Screw Driver
(93).
Install the Pedals (45 L, 46 R) onto the Cranks by using the 13/15mm
Wrench (92). Remember that the left pedal has a reverse thread and
will be screwed into the crank in the opposite rotation from normal
threads. There is an L stamped into the end of the threaded post of the
left pedal and an R on the end of the right post. Make sure to tighten the
pedals as much as you possibly can. It may be necessary to re-tighten
the pedals if you feel a thumping while pedaling the bike. A clicking
noise or thumping feeling is usually caused by loose pedals.
Attach the Seat (19) to the Seat Post (7) using the 12/14mm Wrench
(100).
Dyaco Canada Inc. 2013
8
#58. M5 x 12mm
Phillips Head Screw
(6 pcs)
[email protected]
4 ASSEMBLY STEP 4
FITNESS BIKE FEATURES
FOOT PEDALS
Through research performed with a leading sports scientist and physical rehabilitation
expert, Sole engineering has developed a breakthrough in pedal design. Typical
stationary exercise bikes are wider than a normal road bike. The reason is to allow for
the braking mechanism, pulleys, drive components and plastic covers. Since the bike is
wider, so is the distance between the pedals; this width between the pedals is called the
Q factor.
Sole has designed our pedal system so the Q factor is the smallest in the industry, but
we did not stop there. We have also custom designed and tooled a new pedal that
provides a two degree inward tilt to compensate for the Q factor not being perfect.
Having a small Q factor in addition to the two-degree inward tilt of the pedals puts the
user into a biomechanical neutral alignment. This means that your feet, ankles, knees
and hips are lined up properly ensuring a comfortable workout.
Dyaco Canada Inc. 2013
9
[email protected]
OPERATION OF YOUR FITNESS BIKE
GETTING FAMILIAR WITH THE CONTROL PANEL
CONSOLE
COOLING FAN
QUICK LEVEL KEYS
DATA DISPLAY
PROGRAM BUTTONS
DOT MATRIX
(Manual, Hill, Fat Burn,
Cardio, Strength, Interval,
Custom, Fit-Test, 2HR)
MESSAGE WINDOW
(Program Profiles)
(Time, Program Name,
Distance, RPM,
Calories, Laps, Level,
Watts, & Pulse)
DISPLAY
FAN POWER SWITCH
CONTROL KEYS
HEADPHONE JACK
AUDIO IN JACK
(MP3, CD, or
SMARTPHONE)
POWER UP
The console power is created by a built in generator. When you begin pedaling the
fitness bike, the console will automatically power up. If there is no movement at the
flywheel, the console will go to stand-by mode. In stand-by mode the console display
will turn off. To turn the console on, begin pedaling.
When it is first powered on, the console will perform an internal self-test. During this
time all the lights will turn on. When the lights go off, the Message window will show a
software version (i.e.: VER 1.0) and the Distance window will display an odometer
reading. The odometer reading displays how many virtual miles the fitness bike has
gone. The Time window displays how many hours the fitness bike has been used.
The odometer and time will remain displayed for only a few seconds then the console
will go to the startup display. The dot matrix display will be scrolling through the different
workout profiles and the Message window will be scrolling the start up message. You
may now begin to use the console.
Dyaco Canada Inc. 2013
10
[email protected]
CONSOLE OPERATION
QUICK START
This is the quickest way to start a workout. After
the console powers up you just press the Start
key to begin, this will initiate the Quick Start mode.
In Quick Start the Time will count up from zero and
the workload and the resistance may be adjusted
manually by pressing the Up or Down buttons or
pressing one of the Quick Level Keys 1, 4, 8, 12,
16, 20, 21, 24, 28, 32, 36, or 40 on the left or right
side of the console. The dot matrix display will be
showing a track with a blinking dot indicating your
progress as it travels around the track.
BASIC INFORMATION
The Message Window will initially be displaying the Speed in MPH. Each time the
Display Button - located left of the display - is pressed the next set of information will
appear. The information displayed will be: Speed in MPH, Watts, METs and Segment
Time. Pressing the Display Button one more time will set the display to Scan mode
where all of the information will be displayed sequentially for 4 seconds each. The Dot
Matrix will show the Resistance profile of the program and a Lap Track that is a ¼ mile
long.
There is an Audio Input Jack (
) on the front of the console and built-in speakers.
You may plug any low-level audio source signal into this port. Audio sources include MP3,
iPod, portable radio, CD player or even a TV or computer audio signal. There is an audio
patch cable included to and also a Headphone jack (
) for private listening.
DOT MATRIX CENTER DISPLAY
The fitness bike has a built in heart rate monitoring system. Simply grasping the Contact
Heart Rate Sensors on the handle bars or wearing a chest strap transmitter (sold
separately) will start the heart (see Heart Rate Programs) Icon blinking (this may take a
few seconds). The Pulse Window will display your heart rate in beats per minute and the
HR bar graph will show your current % in relation to projected heart rate maximum. The
chest strap is a more accurate and reliable method of heart rate reading. The hand pulse
sensors are subject to false readings depending on user physiology and workout habits
including how one grips the sensors or how sweaty their hands are.
Because of the generator system, the console will shut off if there isn’t any movement
at the flywheel. If you are in a program and have to stop pedaling, your information will
be saved for up to 5 minutes. When you resume pedaling, the program will continue at
that point and data will continue to accumulate from where you left off. If more than 5
minutes has elapsed, the console will return to the start up screen and all data from
that workout will be lost.
Dyaco Canada Inc. 2013
11
[email protected]
The Stop button actually has several functions. Pressing the Stop key once during a
program will Pause the program. If the Stop button is pressed twice during a workout
the program will end and a Workout Summary is displayed. If the Stop key is held
down for 3 seconds the console will perform a complete Reset. During data entry for a
program the Stop key performs a Previous Screen function. This allows you to go
back one step in the programming each time you press the Stop key.
PROGRAMMING THE CONSOLE
Each of the programs can be customized with your personal information and changed
to suit your needs. Some of the information asked for is necessary to ensure the
readouts are correct. You will be asked for your Age and Weight. Entering your Age is
necessary during the Heart Rate control program to ensure the correct settings are
entered in the program; entering your exact Weight results in a more accurate Calorie
calculation. Although we cannot provide an exact calorie count we do want to be as
close as possible.
A message about Calories: Calorie readings on every piece of exercise equipment,
whether it is in a gym or at home, are not accurate and tend to vary widely. They are
meant only as a guide to monitor your progress from workout to workout. The only way
to measure your calorie burn accurately as in a clinical setting connected to a host of
machines. This is because every person is different and burns calories at a different
rate.
ENTERING A PROGRAM AND CHANGING SETTINGS
Press each program button to scroll through the program selections. The profile for
each program will be displayed in the dot matrix window. Press the Enter key to select
a program and begin customizing the settings. If you want to workout without entering
new settings, then just press the Start key. This will bypass the programming of data
and take you directly to the start of your workout. If you want to change the personal
settings, then just follow the instructions in the message window. If you start a
program without changing the settings, the default settings will be used.
Note: Age and Weight default settings will change when you enter a new number. So
the last Age and Weight entered will be saved as the new default settings. If you enter
Age and Weight the first time you use the fitness bike you will not have to enter it every
time you work out unless either Age or Weight has changed or someone else enters a
different Age and Weight.
Dyaco Canada Inc. 2013
12
[email protected]
PROGRAMMABLE FEATURES
MANUAL PROGRAM
The Manual program works as the name implies, manually. This means that you
control the workload yourself and not the computer.
1. Press the Manual program button then press the Enter key.
2. The Message Window will ask you to enter your Age. You may adjust the age
setting using the Up and Down keys, then press the Enter key to accept the new
number and proceed on to the next screen.
3. You are now asked to enter your Weight. You may adjust your weight setting using
the Up and Down keys, then press Enter to continue.
4. Next is the Time. You may adjust the length of Time by pressing the Up or Down
keys, then press Enter to continue..
5. Now you are finished editing the settings and can begin your workout by pressing
the Start key. You can also go back and modify your settings by pressing the Stop
key to go back one level of the programming screen.
6. Once the program starts the fitness bike will be set to level one. This is the easiest
level and it is a good idea to stay at level one for a while to warm up. If you want to
increase the work load at any time press the Up key; the Down key will decrease
the workload. You can also press any of the Quick Level keys.
7. During the Manual program you will be able to scroll through the data in the
message window by pressing the Display key.
8. When the program ends the message window will show a summary of your
workout. The summary will be displayed for a short time then the console will
return to the start-up display.
Dyaco Canada Inc. 2013
13
[email protected]
PRESET PROGRAMS
The fitness bike has five different programs that have been designed for a variety of
workouts. These five programs have factory preset work level profiles for achieving
different goals.
Hill
The Hill program simulates going up and down a hill. The resistance in the pedals will steadily
increase and then decrease during the program.
WORK
Fat Burn
The Fat Burn program is designed, as the name implies, to maximize the burning of fat. There are
many schools of thought on the best way to burn fat but most experts agree that a lower exertion
level that stays at a steady workload is the best. The absolute best way to burn fat is to keep your
heart rate at around 60% to 70% of its maximum potential. This program does not use heart rate
but simulates a lower, steady exertion workout.
WORK
Cardio
The Cardio program is designed to increase your cardiovascular function and endurance. This is
exercise for your heart and lungs. It will build up your heart muscle and increase blood flow and
lung capacity. This is achieved by incorporating a higher level of exertion with slight fluctuations in
work.
WORK
Strength
The Strength program is designed to increase muscular strength in your lower body. This program
will steadily increase in resistance to a high level and forces you to sustain it. This is designed to
strengthen and tone your legs and glutes (muscles of the butt).
WORK
Interval
The Interval program takes you through high levels of intensity followed by periods of low intensity.
This program increases your endurance by depleting your oxygen level followed by periods of
recovery to replenish oxygen. Your cardiovascular system gets programmed to use oxygen more
efficiently this way. This program also forces your body to become more efficient due to spikes in
heart rate, between recovery periods. This aids in heart rate recovery from intense activities
WORK
Dyaco Canada Inc. 2013
14
[email protected]
PROGRAMMING PRESET BUTTONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
Press the desired program button then press the Enter
key.
The message window will ask you to enter your Age.
You may adjust the age setting, using the Up and Down
keys, then press the Enter key to accept the new
number and proceed on to the next screen.
You are now asked to enter your Weight. You may adjust your weight using the Up
and Down keys then press Enter to continue.
Next is Time. You may adjust the Time and press Enter to continue.
Now you are asked to adjust the Max Level. This is the peak exertion level you will
experience during the program (the highest colored segment/box of the program
profile). Adjust the level and then press Enter.
Now you are finished editing the settings and can begin your workout by pressing
the Start key. You can also go back and modify your settings by pressing the Stop
key to go back one screen or Enter to go back to the beginning.
If you want to increase or decrease the resistance at any time during the program
press the Up or Down keys.
During the program you will be able to scroll through the data in the message
window by pressing the Display key.
When the program ends the message window will show a summary of your workout.
The summary will be displayed for a short time then the console will return to the
start-up display.
CUSTOM PROGRAM
The customizable User program allows you to build and save your own workout. Follow the
instructions below.
1. Select the Custom program then press Enter. If you have already saved a program,
it will be displayed and you are ready to begin. If not or someone else’s name is
shown, you will have the option of overriding or inputting a username. In the
message window, the letter “A” will be blinking. Use the Up and Down buttons to
select the appropriate first letter of your name (pressing the Up button will switch to
the letter “B”; pressing the Down button will switch to letter “Z”). Press Enter when
the desired letter is displayed. Repeat this process until all of the characters of your
name have been programmed (maximum 7 characters). When finished press
Stop.
2. If there is a program already stored in Custom when you press the key, you will
have an option to run the program as it is or delete the program and build a new
one. At the welcome message screen, when pressing Start or Enter you will be
prompted: Run Program? Use the Up/Down arrows to select Yes or No. If you
select No, you will then be asked if you want to delete the currently saved program.
It is necessary to delete the current program if you want to build a new one.
3. The message window will ask you to enter your Age. You may enter your age using
the Up and Down keys, then press the Enter key to accept the new number and
proceed on to the next screen.
4. You are now asked to enter your Weight. You may adjust the weight number using
the Up and Down keys, then press Enter to continue.
5. Next is Time. You may adjust the Time using the Up and Down keys and press
Enter to continue.
Dyaco Canada Inc. 2013
15
[email protected]
6. Now the first column will be blinking and you are asked to adjust the level for the
first segment of the workout. When you finish adjusting the first segment, or if you
don’t want to change, then press Enter to continue to the next segment. The next
segment will show the same level as the previously adjusted segment. Repeat the
same process as the last segment then press Enter. Continue this process until all
twenty segments have been set.
7. The message window will then tell you to start to begin (and save the program) or
Enter to modify the program. Pressing Stop will exit to the start up screen.
8. If you want to increase or decrease the workload at any time during the program
press the Up or Down key. This will only affect the resistance for the present
column in the profile. When the profile changes to the next column it will return to
the preset work level.
9. During the Custom program you will be able to scroll through the data in the message
window by pressing the Display key.
10. When the program ends the message window will show a summary of your workout. The
summary will be displayed for a short time then the console will return to the start-up
display.
FITNESS TEST PROGRAM
The fitness test is based on the YMCA protocol and is a sub-maximal test that uses
pre-determined, fixed work levels that are based on your heart rate readings as the test
progresses. The test will take anywhere between 6 to 15 minutes to complete, depending
on your level of fitness. The test ends when your heart rate reaches 85% of maxi- mum at
any time during the test or your heart rate is between 110 bpm and 85% at the end of two
consecutive stages. At the end of the test a VO2max score will be given. VO2max stands
for Volume of Oxygen uptake which is a measurement of how much oxygen you need to
perform a known amount of work. The YMCA protocol uses two to four, 3 minute stages of
continuous exercise (see charts below). You will be asked to choose either, Male or
Female at the beginning of the test. This choice determines which test parameters will be
used during the test as show in the charts below. The only caveats are that if you are a
very de-conditioned Male you need to choose option Female. If you are a very conditioned
female you need to choose option Male.
Workload chart for male or very fit female:
1st
Stage
300
kgm/min
HR
<90
90-105
>105
2nd
stage
900
kgm/min
750
kgm/min
600
kgm/min
HR
HR<120
HR120-135
HR>135
HR>120
HR120-135
HR>135
HR>120
HR120-135
HR>135
3rd
stage
1350
kgm/min
1200
kgm/min
1050
kgm/min
1200
kgm/min
1050
kgm/min
900
kgm/min
1050
kgm/min
900
kgm/min
750
kgm/min
Workload chart for female or de-conditioned male
1st Stage
150 kgm/min
Heart Rate
HR<80
HR: 80-90
HR: 90-100
2nd Stage
750 kgm/min
600 kgm/min
450 kgm/min
300 kgm/min
3rd Stage
900 kgm/min
750 kgm/min
600 kgm/min
450 kgm/min
4th Stage
1050 kgm/min
900 kgm/min
700 kgm/min
600 kgm/min
Dyaco Canada Inc. 2013
16
HR>100
[email protected]
Fitness Test Programming
1.
2.
3.
4.
5.
Press the Fit-test button and press Enter.
The message window will display Gender Male. The word Male will be blinking. Use
the up and down arrows if you need to change to Female, then press Enter. The choice
of Gender determines which workload chart will be used for the test.
The message window will ask you to enter your Age. You may adjust the age setting,
using the Up and Down keys then press the Enter key to accept the new number and
proceed on to the next screen
You are now asked to enter your Weight. You may adjust the weight number using the
Up and Down keys then press enter to continue.
Now press Start to begin the test or Enter to modify your settings.
Before the test
Make sure you are in good health; check with your physician before performing any
exercise if you are over the age of 35 or persons with pre-existing health conditions.
Make sure you have warmed up and stretched before taking the test.
Do not take in caffeine before the test.
Hold the hand grips gently, do not tense up.
During the test
The console must be receiving a steady heart rate for the test to begin. You may use
the hand pulse sensors or wear a heart rate chest strap transmitter.
You must maintain a steady 50 RPM pedal speed. If your pedal speed drops below 48
RPM or goes above 52 RPM the console will emit a steady beeping sound until you
are within this range.
You may scroll through the various data readings in the message window by pressing
the Display button under the Message Window.
6. The message window will always display your pedal speed on the right side to help you
maintain 50RPM.
7. The data shown during the test is:
a. Work in KGM is actually an abbreviated form of kg-m/min. which is a
work measurement of kilogram-force meter/minute
b. Work in Watts (1 watt is equal to 6.11829727787 kg-m/min.)
c. HR is your actual heart rate; TGT is the target heart rate to reach to
end the test. d. Time is the total elapsed time of the test.
After the test
Cool down for about one to three minutes.
Take note of your score because the console will automatically return to the start-up
mode after a few minutes.
WHAT YOUR SCORE MEANS
VO2max Chart for males and very fit females
excellent
good
above
average
average
below
average
poor
very
poor
18-25
Years
old
>60
52-60
47-51
26-35
Years
old
>56
49-56
43-48
36-45
Years
old
>51
43-51
39-42
46-55
Years
old
>45
39-45
35-38
56-65
Years
old
>41
36-41
32-35
65+
Years
old
>37
33-37
29-32
42-46
37-41
40-42
35-39
35-38
31-34
32-35
29-31
30-31
26-29
26-28
22-25
30-36
<30
30-34
<30
26-30
<26
25-28
<25
22-25
<22
20-21
<20
Dyaco Canada Inc. 2013
VO2max Chart for females and de-conditioned males
excellent
good
above
average
average
below
average
poor
very
poor
17
18-25
Years
old
56
47-56
42-46
26-35
Years
old
52
45-52
39-44
36-45
Years
old
45
38-45
34-37
46-55
Years
old
40
34-40
31-33
56-65
Years
old
37
32-37
28-31
65+
Years
old
32
28-32
25-27
38-41
33-37
35-38
31-34
31-33
27-30
28-30
25-27
25-27
22-24
22-24
19-22
28-32
<28
26-30
<26
22-26
<22
20-24
<20
18-21
<18
17-18
<17
[email protected]
HEART RATE PROGRAMS
Before we get started, a word about Heart Rate:
The old motto, “no pain, no gain”, is a myth that has been overpowered by the benefits of
exercising comfortably. A great deal of this success has been promoted by the use of
heart rate monitors. With the proper use of a heart rate monitor, many people find that
their usual choice of exercise intensity was either too high or too low and exercise is much
more enjoyable by maintaining their heart rate in the desired benefit range.
To determine the benefit range in which you wish to train, you must first determine your
Maximum Heart Rate. This can be accomplished by using the following formula: 220
minus your age. This will give you the Maximum Heart Rate (MHR)for someone of your
age. To determine the effective heart rate range for specific goals you simply calculate a
percentage your MHR. Your Heart rate training zone is 50% to 90% of your maximum
heart rate. 60% of your MHR is the zone that burns fat while 80% is for strengthening
the cardio vascular system. This 60% to
80% is the zone to stay in for maximum
benefit.
For someone who is 40 years old their
target heart rate zone is calculated:
220 – 40 = 180 (maximum heart rate)
180 x .6 = 108 beats per minute
(60% of maximum)
180 X .8 = 144 beats per minute
(80% of maximum)
So for a 40 year old the training zone
would be 108 to 144 beats per minute.
If you enter your age during programming the console will perform this calculation
automatically. Entering your age is used for the Heart Rate control programs. After
calculating your MHR you can decide upon which goal you would like to pursue.
The two most popular reasons for, or goals, of exercise are cardiovascular fitness
(training for the heart and lungs) and weight control. The black columns on the chart
above represent the MHR for a person whose age is listed at the bottom of each column.
The training heart rate, for either cardiovascular fitness or weight loss, is represented by
two different lines that cut diagonally through the chart. A definition of the lines’ goal is in
the bottom left-hand corner of the chart. If your goal is cardiovascular fitness or if it is
weight loss, it can be achieved by training at 80% or 60%, respectively, of your MHR on a
schedule approved by your physician. Consult your physician before participating in any
exercise program.
With all Heart Rate Control fitness bike machines you may use the heart rate monitor
feature without using the Heart Rate Control program. This function can be used during
manual mode or during any of the nine different programs. The Heart Rate Control
program automatically controls resistance at the pedals.
Dyaco Canada Inc. 2013
18
[email protected]
RATE OF PERCEIVED EXERTION
Heart rate is important but listening to your body also has a lot of advantages. There are
more variables involved in how hard you should workout than just heart rate. Your stress
level, physical health, emotional health, temperature, humidity, the time of day, the last time
you ate and what you ate, all contribute to the intensity at which you should workout. If you
listen to your body, it will tell you all of these things.
The rate of perceived exertion (RPE), also know as the Borg scale, was developed by
Swedish physiologist G.A.V. Borg. This scale rates exercise intensity from 6 to 20 depending
upon how you feel or the perception of your effort.
The scale is as follows:
Rating Perception of Effort
6 Minimal
7 Very,very light
8 Very,very light +
9 Very light
10 Very light +
11 Fairly light
12 Comfortable
13 Somewhat hard
14 Somewhat hard +
15 Hard
16 Hard +
17 Very hard
18 Very hard +
19 Very,very hard
20 Maximal
You can get an approximate heart rate level for each rating by simply adding a zero to each
rating. For example a rating of 12 will result in an approximate heart rate of 120 beats per
minute. Your RPE will vary depending up the factors discussed earlier. That is the major
benefit of this type of training. If your body is strong and rested, you will feel strong and your
pace will feel easier. When your body is in this condition, you are able to train harder and the
RPE will support this. If you are feeling tired and sluggish, it is because your body needs a
break. In this condition, your pace will feel harder. Again, this will show up in your RPE and
you will train at the proper level for that day.
Dyaco Canada Inc. 2013
19
[email protected]
USING HEART RATE TRANSMITTER(Optional)
How to wear your wireless chest strap transmitter:
1.
2.
3.
4.
5.
6.
Attach the transmitter to the elastic strap using the locking
parts.
Adjust the strap as tightly as possible as long as the strap is
not too tight to remain comfortable.
Position the transmitter with the logo centered in the middle
of your body facing away from your chest (some people
must position the transmitter slightly left of center). Attach
the final end of the elastic strap by inserting the round end
and, using the locking parts, secure the transmitter and
strap around your chest.
Position the transmitter immediately below the pectoral muscles.
Sweat is the best conductor to measure very minute heart beat electrical signals.
However, plain water can also be used to pre-wet the electrodes (2 ribbed oval areas
on the reverse side of the belt and both sides of the transmitter). It’s also
recommended that you wear the transmitter strap a few minutes before your work out.
Some users, because of body chemistry, have a more difficult time in achieving a
strong, steady signal at the beginning. After “warming up”, this problem lessens. As
noted, wearing clothing over the transmitter/strap doesn’t affect performance.
Your workout must be within range - distance between transmitter/receiver – to
achieve a strong steady signal. The length of range may vary somewhat but
generally stay close enough to the console to maintain good, strong, reliable
readings. Wearing the transmitter immediately against bare skin assures you of
proper operation. If you wish, you may wear the transmitter over a shirt. To do so,
moisten the areas of the shirt that the electrodes will rest upon.
Note: The transmitter is automatically activated when it detects activity from the user’s heart. Additionally,
it automatically deactivates when it does not receive any activity. Although the transmitter is water resistant,
moisture can have the effect of creating false signals, so you should take precautions to completely dry the
transmitter after use to prolong battery life (estimated transmitter battery life is 2500 hours). The
replacement battery is Panasonic CR2032.
ERRATIC OPERATION
Caution! Do not use this fitness bike for Heart Rate Control unless a steady, solid Actual
Heart Rate value is being displayed. High, wild, random numbers being displayed
indicate a problem.
Areas to look for interference which may cause erratic heart rate:
Microwave ovens, TV’s, small appliances, etc.
Fluorescent lights.
Some household security systems.
Perimeter fence for a pet.
Some people have problems with the transmitter picking up a signal from their skin. If
you have problems try wearing the transmitter upside down. Normally the transmitter
will be oriented so the logo is right side up.
6. The antenna that picks up your heart rate is very sensitive. If there is an outside
noise source, turning the whole machine 90 degrees may de-tune the interference.
7. Another Individual wearing a transmitter within 3’ of your machine’s console.
1.
2.
3.
4.
5.
If you continue to experience problems contact your dealer.
Dyaco Canada Inc. 2013
20
[email protected]
HEART RATE CONTROL PROGRAM OPERATION
Both programs operate the same, the only difference is that HR1 is set to 60% and HR2
is set to 80% of the maximum heart rate. They both are programmed the same way.
To start an HR program follow the instructions below or just select the HR1 or HR2
program, then the Enter button and follow the directions in the message window.
1. Press the HR1 or HR2 key then press the Enter key.
2. The message window will ask you to enter your Age. You may enter your Age,
using the Up and Down keys, then press the Enter key to accept the new number
and proceed on to the next screen.
3. 3. You are now asked to enter your Weight. You may adjust the Weight number
using the Up and Down keys, then press Enter to continue.
4. Next is Time. You may adjust the Time and press Enter to continue.
5. Now you are asked to adjust your Target Heart Rate. This is the heart rate level
you will strive to reach and maintain during the program. Adjust the level and then
press Enter. NOTE: The heart rate that appears is based on the % you accepted in Step
1. If you change this number it will either increase or decrease the % from Step 1.
6. Now you are finished editing the settings and can begin your workout by pressing
the Start key. You can also go back and modify your settings by pressing the Enter
key.
NOTE: At any time during the editing of Data you can press the Stop key to go back one
level, or screen.
7. If you want to increase or decrease the workload at any time during the program
press the Up or Down key. This will allow you to change your target heart rate at
any time during the program.
8. During the HR1 or HR2 programs you will be able to scroll through the data in the
message window by pressing the adjacent Display key.
9. When the program ends you may press Start to begin the same program again or
Stop to exit the program.
Dyaco Canada Inc. 2013
21
[email protected]
GENERAL MAINTENANCE
1.
2.
Wipe down all areas in the sweat path with a damp cloth after each workout.
If a squeak, thump, clicking or rough feeling develops the main cause is most likely
one of two reasons:
I.
The hardware was not sufficiently tightened during assembly. All bolts that
were installed during assembly need to be tightened as much as possible. It
may be necessary to use a larger wrench than the one provided if you cannot
tighten the bolts sufficiently. I cannot stress this point enough; 90% of calls to
the service department for noise issues can be traced to loose hardware.
II. The crank arm nut needs to be retightened
III. If squeaks or other noises persist, check that the unit is properly leveled.
There are 2 leveling pads on the bottom of the rear stabilizer, use a 14mm
wrench (or adjustable wrench) to adjust the levelers.
MAINTENANCE MENU IN CONSOLE SOFTWARE
1. Press and hold the Start, Stop and Enter key at the same time, until the display
shows “Engineering Mode”. Press the Enter key.
2. You can now scroll through the menu using the Up and Down keys. Use the Stop key
to return to previous menu selection. The menu selections are:
A. Key Test
B. Display Test
C. Functions
I. Display Mode - Turn Off to have the console power down automatically after 30
minutes of inactivity
II. Pause Mode - Turned On to allow 5 minutes of Pause, turn Off to Pause indefinitely
III. ODO Reset - Resets the Odometer reading to zero
IV. Units - Choose from English(Imperial) or Metric display readings
V. Brake Test - For testing the Brake function
D. Security
E. Factory Settings - For Factory use only
F. Exit
Dyaco Canada Inc. 2013
22
[email protected]
EXPLODED VIEW DIAGRAM
Dyaco Canada Inc. 2013
23
[email protected]
PARTS LIST
KEY NO.
1
2
3
5
6
7
8
9
11
13
14
15
16L
16R
17
18
19
20
21
22
23
24
25
26
28
29
30
31
32
34
35
36
37
38
40
41
42
43
45
46
47
49
50
51
52
53
54
55
56
Dyaco Canada Inc. 2013
PART NO.
6737901
01
6737902
6737903
6737905
6737906
6737907
6737908
6737909
6737911
6737913
6737914
6737915
6737916L
6737916R
6737917
6737918
6737919
6737920
6737921
6737922
6737923
6737924
6737925
6737926
6737928
6737929
6737930
6737931
6737932
6737934
6737935
6737936
6737937
6737938
6737940
6737941
6737942
6737943
6737945
6737946
6737947
6737949
6737950
6737951
6737952
6737953
6737954
6737955
6737956
Description
Main Frame
Console Mast
Handle Bar
Rear Stabilizer
Seat Slider
Sliding Seat Mount
Fix Plate
Idler Wheel Assembly
Crank Axle
Chain Cover Bracket
Drive Belt
Drive Pulley
Crank Arm(L)
Crank Arm(R)
6004_Bearing
6203_Bearing
Seat
Generator/Brake
Generator/Brake Controller
Magnet
300m/m_Sensor W/Cable
1" × 5T × 285m/m_Handgrip Foam
1" × 5T × 200m/m_Handgrip Foam
800m/m_Handpulse W/Cable Assembly
800m/m_Handpulse W/Cable Assembly
2100m/m_Computer Cable
200m/m_Wire Brake Coil Harness
Generator Wire Harness
1400m/m_Ground Wire
Console assembly
Rubber Foot
Chain Cover (L)
Chain Cover (R)
Console Mast Cover
Front Stabilizer Cover
Rear Stabilizer Cover
Handgrip Side Cap (Top)
Handgrip Side Cap (Bottom)
Pedal(L)
Pedal(R)
Transportation Wheel
Button Head Plug
3/8" × 2-1/4"_Hex Head Bolt
5/16" × 5/8"_Hex Head Bolt
5 × 19m/m_Tapping Screw
5/16" × 1-3/4"_Button Head Socket Bolt
1/4" × 3/4"_Hex Head Bolt
M8 × 170m/m_J Bolt
M6 × 15m/m_Phillips Head Screw
24
Q’TY
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
2
2
1
1
1
1
1
1
1
4
1
1
1
1
1
2
2
1
1
2
4
2
9
2
2
8
1
3
[email protected]
KEY NO.
57
58
59
61
62
63
65
66
67
68
69
70
71
72
73
76
77
78
79
80
82
83
86
92
93
95
96
99
100
101
102
103
105
106
107
109
114
118
124
131
Dyaco Canada Inc. 2013
PART NO.
6737957
6737958
6737959
6737961
6737962
6737963
6737965
6737966
6737967
6737968
6737969
6737970
6737971
6737972
6737973
6737976
6737977
6737978
6737979
6737980
6737982
6737983
6737986
6737992
6737993
6737995
6737996
6737999
67379100
67379101
67379102
67379103
67379105
67379106
67379107
67379109
67379114
67379118
67379124
67379131
Description
3/16" × 15m/m × 1.5T_Flat Washer
M5 × 12m/m_Phillips Head Screw
3/8" × 2m/m_Flat Head Socket Bolt
5 × 16m/m_Tapping Screw
Ø3 × 20m/m_Tapping Screw
Ø3.5 × 16m/m_Sheet Metal Screw
Ø3 × 10m/m_Tapping Screw
Ø17_C Ring(Blackfast)
Ø20_C Ring(Blackfast)
4 × 12m/m_Sheet Metal Screw
1/4" × 13m/m × 1T_Flat Washer
3/8" × 19m/m × 1.5T_Flat Washer
3/8" × 25m/m × 2T_Flat Washer
5/16" × 18m/m × 1.5T_Flat Washer
Ø17 × 23.5m/m × 1T_Flat Washer
Ø1/4"_Split Washer
M8 × 7T_Nyloc Nut
3/8" × 7T_Cap Nut
1/4" × 8T_Nyloc Nut
5/16" × 6T_Nyloc Nut
3/8" × 7T_Nut
M10 × 1.25m/m_Nut
Seat Fore/Aft Adjustment Knob
13/15m/m_Wrench
Phillips Head Screw Driver
Chest Strap (Optional)
Crank Arm End Cap
5/16" × 19m/m × 1.5T_Curved Washer
12/14m/m_Wrench
Drink Bottle (Optional)
5/16" × 16 × 1T_Flat Washer
5/16" × 1.5T_Split Washer
Handle Bar Cover
Locking Knob
Center spatial wrap
400m/m_Audio Cable (Optional)
Slide Spacer
5/16" × 2-1/4"_Hex Head Bolt
On/Off Switch Bracket
Rear Stabilizer Attaching Plate
25
Q’TY
1
9
4
7
4
8
4
1
2
2
7
4
3
9
1
7
1
1
4
4
8
2
1
1
1
1
2
1
1
1
2
2
1
1
1
1
1
2
1
1
[email protected]
MANUFACTURER’S LIMITED WARRANTY
Dyaco Canada Inc. warrants all its fitness bike parts for a period of time listed below from the date of retail sale, as
determined by sale receipt, or in the absence of a sales receipt eighteen (18) months from the original factory shipping date.
Dyaco Canada Inc.’s responsibilities include providing new or remanufactured parts, at Dyaco Canada Inc.’s option, and
technical support to our independent dealers and servicing organizations. In the absence of a dealer or service organization,
these warranties will be administered by Dyaco Canada Inc. directly to a consumer. The warranty period applies to the
following components:
Frame
lifetime
Parts
3 years
Labour
1 year
This warranty applies only to products in ordinary household use, and the consumer is responsible for the items listed below:
1. The warranty registration card must be completed and returned to the address listed on the card within 10 days of the
original purchase to validate the Dyaco Canada Inc.’s limited warranty.
2. Proper use of the fitness bike in accordance with the instructions provided in this manual.
3. Proper installation in accordance with instructions provided with the fitness bike and with all local electric codes.
4. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose
connections or defects in house wiring.
5. Expenses for making the fitness bike accessible for servicing, including any item that was not part of the fitness bike at
the time it was shipped from the factory.
6. Damages to the fitness bike finish during shipping, installation or following installation.
7. Routine maintenance of this unit as specified in this manual.
EXCLUSIONS
This warranty does not cover the following:
1. CONSEQUENTIAL, COLLATERAL, OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND
INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or
exclusion may not apply to you.
2. Service call reimbursement to the consumer. Service call reimbursement to the dealer that does not involve
malfunction or defects in workmanship or material, for units that are beyond the warranty period, for units that are
beyond the service call reimbursement period, for fitness bike not requiring component replacement, or fitness bike not
in ordinary household use.
3. Damages caused by services performed by persons other than authorized Dyaco Canada Inc. service companies; use
of parts other than original Dyaco Canada Inc. parts; or external causes such as corrosion, discoloration of paint or
plastic, alterations, modifications, abuse, misuse, accident, improper maintenance, inadequate power supply, or acts
of God.
4. Products with original serial numbers that have been removed or altered.
5. Products that have been: sold, transferred, bartered, or given to a third party.
6. Products that do not have a warranty registration card on file at Dyaco Canada Inc. Dyaco Canada Inc. reserves the
right to request proof of purchase if no warranty record exists for the product.
7. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE.
8. Product use in any environment other than a residential setting.
9. Warranties outside of North America may vary. Please contact your local dealer for details.
SERVICE
by the serial number establishes the labor warranty period should service be required. If service is performed, it is in your
best interest to obtain and keep all receipts. This written warranty gives you specific legal rights. You may also have other
rights that vary from state to state. Service under this warranty must be obtained by following these steps, in order:
1. Contact your selling authorized SOLE dealer. OR
2. If you have any questions about your new product or questions about the warranty contact Dyaco Canada Inc. at
1-888-707-1880.
3. If no local service is available, Dyaco Canada Inc. will repair or replace the parts, at Dyaco Canada Inc.’s option, within
the warranty period at no charge for parts. All transportation costs, both to our factory and upon return to the owner,
are the responsibility of the owner. The owner is responsible for adequate packaging upon return to Dyaco Canada Inc.
Dyaco Canada Inc. is not responsible for damages that occur during shipping. Make all freight damage claims with the
appropriate freight carrier. DO NOT SHIP ANY UNIT TO OUR FACTORY WITHOUT A RETURN AUTHORIZATION
NUMBER. All units arriving without a return authorization number will be refused.
4. For any further information, or to contact our service department by mail, send your correspondence to:
Dyaco Canada Inc.
6050 Don Murie Street
Niagara Falls, ON
L2G 0B3
Product features or specifications as described or illustrated are subject to change without notice. All warranties are made
by Dyaco Canada Inc.
Dyaco Canada Inc. 2013
26
[email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement