-0xx (JA60/JA61) Wireless Intercom System

-0xx (JA60/JA61) Wireless Intercom System
-0xx (JA60/JA61)
Wireless Intercom System
Operating Manual
Rev. C
Page 1
wiJAC-00x Wireless Intercom System
Operating Manual
Copyright 2013 Jupiter Avionics Corp.
All rights reserved
Jupiter Avionics Corporation (JAC) permits a single copy of this manual to
be printed or downloaded for personal use. Any such electronic or printed
copy of this manual must contain the complete text of this copyright
notice. Any unauthorized commercial distribution of this manual is strictly
prohibited. Except as described above, no part of this manual may be
reproduced, copied, transmitted, disseminated, downloaded, or stored in
any storage medium for any purpose without the express prior written
consent of JAC.
IMPORTANT:
Information in this manual is subject to change without notice.
To confirm the current revision status of this manual,
visit the JAC website:
www.jupiteravionics.com
Rev
A
B
C
Date
Jun 2013
Sep 2013
Jun 2016
Record of Revisions
Description
Add Freq. and RF output; change drawing
ECR
1964/5
2270
4281
Prepared:
Checked:
MPB
JAC
JAC
06-24-16
06-24-16
MB
KDV
Rev C
Approved:
Page i
wiJAC-00x Wireless Intercom System
Operating Manual
Table of Contents
Introduction ................................................................................................. 1
1.1
Unpacking ............................................................................................ 2
1.2
Verify Operating Region ....................................................................... 2
1.3
Verify Pairing Registration Number ....................................................... 2
2
JA60-00x Headset Adapter (JA60) .............................................................. 3
3
JA61-00x Intercom Adapter (JA61)............................................................. 3
4
Controls, Annunciators and Connectors ................................................... 4
4.1
 (ON/OFF) Button – Both units ........................................................... 4
4.2
Controls – JA60 .................................................................................... 4
1
4.2.1
4.2.2
4.2.3
4.3
4.4
4.5
4.5.1
4.5.2
Headset Jack – JA60 ............................................................................ 4
Intercom Connector – JA61 .................................................................. 4
Connectors – Both units ....................................................................... 5
IO Configuration Port (Dealers only) .................................................. 5
PWR (Charging Port)......................................................................... 5
4.6
Annunciators – Both Units .................................................................... 5
4.7
Other .................................................................................................... 6
4.6.1
4.6.2
4.6.3
4.7.1
4.7.2
4.7.3
5
VOX (Voice Operated Switch) ........................................................... 4
VOL (Phones Volume Control) .......................................................... 4
PTT (Push To Talk) Button ................................................................ 4
PWR ON (Power On) ........................................................................ 5
LOW BATT (Low Battery Warning).................................................... 5
Battery Charge (not shown) ............................................................... 5
Pairing Registration Number .............................................................. 6
Battery Lid Release ........................................................................... 6
Clothing/Mounting Clip ...................................................................... 6
Connecting the wiJAC™ System ............................................................... 7
5.1
wiJAC™ Set-up and Connection .......................................................... 8
5.1.1
5.1.2
5.1.3
5.1.4
5.2
5.2.1
5.2.2
5.2.3
5.2.4
5.2.5
5.2.6
5.2.7
5.2.8
5.2.9
Insert Batteries .................................................................................. 8
Attach Connectors to Aircraft and Headset ........................................ 8
Turn On Adapters and Verify Connection ........................................... 8
Verify Audio Operation ...................................................................... 8
wiJAC™System Operation................................................................... 9
Overview ........................................................................................... 9
Listening Operation ........................................................................... 9
VOX Speaking Operation .................................................................. 9
PTT Speaking Operation ................................................................... 9
Live Speaking Operation ................................................................... 9
Low Battery Warning ......................................................................... 9
Operation during Charging .............................................................. 10
Loss of Audio .................................................................................. 10
Battery Life ...................................................................................... 10
6
Batteries..................................................................................................... 11
6.1
Inserting or Replacing the Batteries .................................................... 11
6.2
Charging Batteries in the Unit ............................................................. 11
6.3
Charging Operation – via Battery Charger .......................................... 12
6.4
Battery Cautions and Warnings .......................................................... 12
7
Accessories ............................................................................................... 13
7.1
JA72-005 Glove Box with USB connector ........................................... 13
7.2
ProCS™ Product Configuration Software ........................................... 13
7.3
Battery Charger Recommendations .................................................... 13
8
Installation of the JA61 Mounting Bracket............................................... 14
9
Specifications ............................................................................................ 15
9.1
Mechanical ......................................................................................... 15
9.2
Electrical ............................................................................................. 15
9.3
Environmental .................................................................................... 15
9.4
Other .................................................................................................. 15
10 Warranty .................................................................................................... 16
11 FCC Compliance Statement...................................................................... 16
Rev C
Page ii
wiJAC-00x Wireless Intercom System
Operating Manual
1
Introduction
This manual contains the operating instructions for the wiJAC-00x Wireless
Intercom System.
The diagram below describes the naming method for the different systems.
wiJAC-0 x x
Not Allocated
System Type:
0 = Base Model
Operating Region:
1 = N America
2 = Europe
North America:
The wiJAC-001 consists of one JA60-001 Wireless Aircraft Headset
Adapter, and one JA61-001 Wireless Aircraft Intercom adapter.
RF output power is 21dBm
Channel frequencies 23 =
24 =
25 =
26 =
27 =
Europe:
(125mW peak)
1.921536 GHz
1.923264 GHz
1.924992 GHz
1.926720 GHz
1.928448 GHz
The wiJAC-002 consists of one JA60-002 Wireless Aircraft Headset
Adapter, and one JA61-002 Wireless Aircraft Intercom adapter.
RF output power is 23 dBm
Channel frequencies 9 =
8=
7=
6=
5=
4=
3=
2=
1=
0=
(200 mW peak)
1.881792 GHz
1.883520 GHz
1.885248 GHz
1.886976 GHz
1.888704 GHz
1.890432 GHz
1.893888 GHz
1.896616 GHz
1.895616 GHz
1.897344 GHz
Only paired units will operate together (see section 1.3)
System operating information is in section 5.2.
WARNING: JAC recommends that no battery operated device
should be relied upon as the sole method of communication in
cases where there is potential risk to life or limb.
Rev C
Page 1
wiJAC-00x Wireless Intercom System
Operating Manual
1.1
Unpacking
Unpack the box carefully, and ensure that it contains the following:
• one ea. Wireless Aircraft Headset Adapter, JAC P/N JA60-00x
• one ea. Wireless Aircraft Intercom Adapter, JAC P/N JA61-00x
• one ea. Mounting Bracket, JAC P/N PLT-CLIP-0004
• two pkg. of AAA rechargeable batteries
• two ea. USB to Micro USB cables, JAC P/N CAB-USB-0003
• one wiJAC™ Quick Start Guide, JAC P/N DOC-GUID-WIJAC
If any of the above items are missing, or there is any sign of damage to the
packaging, contact your dealer immediately.
1.2
Verify Operating Region
The wiJAC-00x Wireless Intercom System operates using radio frequencies
that are authorized by government regulatory agencies. Ensure the region in
which you are operating the units matches the region marked on a label on
the back of each unit.
1.3
Verify Pairing Registration Number
The wiJAC-00x Wireless Intercom System consists of one set of paired
Adapters. The JA60-00x Headset Adapter must be paired with a JA61-00x
Intercom Adapter. Ensure that the same three character Pairing Registration
Number is marked on a label on the back of each unit.
Rev C
Page 2
wiJAC-00x Wireless Intercom System
Operating Manual
2
JA60-00x Headset Adapter (JA60)
ON/OFF Control
Battery Lid Release
LOW BATT
Annunciator
Pairing
Registration
Number
Push To Talk
Button
PWR ON
Annunciator
Belt Clip
Configuration Port
Charging Port
Fig 3-2, JA60 Left Side View
Fig 3-1, JA60 Right Side View
Headset Jack
Microphone Voice
Operated Switch
Control
Phones Volume Control
Fig 3-3, JA60 Top View
3
JA61-00x Intercom Adapter (JA61)
Battery Lid Release
Charging
Port
Panel
Plug
ON/OFF Control
LOW BATT
Annunciator
Mounting Clip
Configuration Port
PWR ON
Annunciator
Pairing
Registration
Number
Fig 3-5, JA61 Left Side View
Fig 3-4, JA61 Right Side View
Note: The units are shown in grey for clarity.
Rev C
Page 3
wiJAC-00x Wireless Intercom System
Operating Manual
4
Controls, Annunciators and Connectors
4.1
(ON/OFF) Button – Both units
The ON/OFF control is a push button switch marked with the  symbol and
is located on the left side of the unit. To turn the unit on, press the ON/OFF
button once. To turn the unit off, press and hold the ON/OFF button until the
PWR ON and LOW BATT annunciators turn off (approximately three to
five seconds).
4.2
Controls – JA60
4.2.1
VOX (Voice Operated Switch)
The Voice Operated Switch control is a rotary knob marked VOX located on
the top of the JA60 Headset Adapter. To reduce the level of the sound
needed to route the microphone audio to the Intercom Adapter, turn the VOX
knob counterclockwise. To increase the level of the sound needed to route
the microphone audio to the Intercom Adapter, turn the VOX knob clockwise.
Adjust this setting for proper VOX operation as ambient noise levels change.
4.2.2
VOL (Phones Volume Control)
WARNING: Loud noise can cause hearing damage. Before
using the headset, set the volume to minimum, and then slowly
increase it to a comfortable listening level.
The volume control is a rotary knob marked VOL (volume) located on the top
of the JA60 Headset Adapter. To reduce the volume of the audio heard in
the headset rotate the VOL knob counterclockwise. To increase the volume
of the audio heard in the headset rotate the VOL knob clockwise.
4.2.3
PTT (Push To Talk) Button
The intercom Push To Talk button is a push button switch marked ICS
located on the right side of the JA60 Headset Adapter. When the ICS PTT
button is pressed and held, the VOX threshold is overridden, microphone
audio is routed to the paired JA61 Intercom Adapter, and the ICS Key output
is activated.
4.3
Headset Jack – JA60
The headset jack is a TJT120 type connector on the top of the JA60 headset
adapter. Insert a U-174/U or U93A/U type Headset plug into the JA60
Headset Adapter headset jack.
4.4
Intercom Connector – JA61
The JA61 Intercom Adapter connects to the aircraft audio panel.
Rev C
Page 4
wiJAC-00x Wireless Intercom System
Operating Manual
4.5
4.5.1
Connectors – Both units
IO Configuration Port (Dealers only)
This port is used by Approved dealers and installers to connect the unit to a
laptop or PC to enable configuration changes using the ProCS™ program.
4.5.2
PWR (Charging Port)
The Charging Port is a Micro-USB connector with a flexible cover labeled
PWR (power) on the left side of the unit. To charge NiMH batteries, connect
a USB (Universal Serial Bus) to Micro USB cable from the Charging Port to
a USB power source.
WARNING: Charging battery types other than NiMH or NiCad
may cause the batteries to leak or explode and cause damage or
injury. If non-NiMH or non-NiCad batteries are installed, do not
connect the Charging Port to a USB power source.
4.6
4.6.1
Annunciators – Both Units
PWR ON (Power On)
The power on (PWR ON) annunciator is a green LED located on the right
side of the unit. In addition to indicating that the unit is turned on, this
annunciator indicates the connection status of paired units (see section
5.1.3)
4.6.2
LOW BATT (Low Battery Warning)
The low battery (LOW BATT) annunciator is a red LED located on the left
side of the unit. When a unit is turned on, the LOW BATT annunciator will
illuminate for 2 seconds.
When the JA60 battery voltage is low the LOW BATT annunciator will flash
once every 1.5 s and a low battery notification (a triple beep) will be heard in
the headphones once every minute. (A similar but higher pitched tone will be
heard if the paired JA61 Intercom Adapter battery charge is low.)
When the unit battery charge is less than or equal to the critical battery
voltage, the unit will turn off.
4.6.3
Battery Charge (not shown)
The JA60 and JA61 Battery Charge annunciators are two LEDs, one on
each side of the charging port under the flexible dust cover marked PWR.
The Fast Charge annunciator is a red light emitting diode (LED) that will
illuminate when the batteries are being charged at the maximum charge
current.
The Top-Off Charge annunciator is a green LED that will illuminate when
Fast Charge mode is complete and the batteries are charged.
Rev C
Page 5
wiJAC-00x Wireless Intercom System
Operating Manual
4.7
4.7.1
Other
Pairing Registration Number
The pairing registration number is marked on a label in on the back of each
unit. A JA60 Headset Adapter will connect only to the JA61 Intercom
Adapter with the same pairing registration number.
4.7.2
Battery Lid Release
The battery lid release is a lever on the front of the unit recessed into the
battery lid (see section 6.1).
4.7.3
Clothing/Mounting Clip
The clothing clip is on the rear of the JA60 Headset Adapter, and the
mounting clip is on the rear of the JA61 Intercom Adapter. Ensure that the
units are attached securely.
Rev C
Page 6
wiJAC-00x Wireless Intercom System
Operating Manual
5
Connecting the wiJAC™ System
Note: The wiJAC-00x Wireless Intercom System consists of one
JA60 Headset Adapter and one JA61 Intercom Adapter. Only paired
units will operate together (see section 5.1.3)
The JA61 Intercom Adapter has a plug that is inserted into a jack in the
aircraft where the headset is normally connected. A headset is inserted into
the jack on the JA60 Headset Adapter, which is clipped to the user's belt or
placed in a pocket. Headset and audio panel are not included.
Typical wiJAC™
Set Up
JA60 Headset Adapter
(Connected to user's headset)
JA61 Intercom Adapter
(Plugged into aircraft headset jack)
WARNING: To avoid loss of communication, always charge
rechargeable batteries before every use.
Rev C
Page 7
wiJAC-00x Wireless Intercom System
Operating Manual
5.1
wiJAC™ Set-up and Connection
5.1.1
Insert Batteries
Ensure the batteries for both units are fully charged and installed in the
battery compartment with the correct polarity, and the battery lid is secured
(section 6).
5.1.2
Attach Connectors to Aircraft and Headset
Connect the JA61 Intercom Adapter plug to a MS3110 Flo-65 or equivalent
connector.
Insert a headset with a U-174/U or U93A/U type plug into the JA60 Headset
Adapter jack.
5.1.3
Turn On Adapters and Verify Connection
On the JA60 Headset Adapter, turn the VOL knob fully counterclockwise to
minimum. Turn on the JA60 Headset Adapter and the JA61 Intercom
Adapter. On both units the PWR ON and LOW BATT annunciators will
illuminate for two seconds.
•
When a unit is turned on, the PWR ON annunciator will illuminate for 2
seconds, and the unit will start to search for its paired unit.
•
While the unit is searching for its paired unit the PWR ON annunciator
will triple-flash every 1.5 seconds.
•
When the unit is connecting to its paired unit, the annunciator will
double-flash every 1.5 s until connection is established.
•
After connection, the annunciator will illuminate steady green until the
unit is turned off.
5.1.4
Verify Audio Operation
Set the aircraft audio system's VOX mode to live or key the aircraft audio
system's ICS PTT for the headset connection used by the JA61 Intercom
Adapter.
Adjust the JA60 Headset Adapter's VOX control to fully counterclockwise
and the VOL control to achieve a comfortable listening level. Confirm that
the microphone audio is live - all microphone audio is heard in the phones.
Confirm that the audio level increases as the VOL control is rotated
clockwise and decreases as the VOL control is rotated counterclockwise.
Adjust the Headset Adapter's VOX control to fully clockwise and confirm that
the microphone audio is off.
Press the Headset Adapter's ICS PTT button and confirm that microphone
audio is heard in the phones. Repeat this process for the TX PTT button.
Adjust the Headset Adapter's VOX control for a comfortable speaking level
and return the aircraft audio system's controls to its previous settings.
Rev C
Page 8
wiJAC-00x Wireless Intercom System
Operating Manual
5.2
5.2.1
wiJAC™System Operation
Overview
When both units are turned on and connected, phones audio from the
aircraft audio system is transmitted from the Intercom Adapter, received by
the Headset Adapter and output on the headset's phones. Microphone audio
from the headset's microphone is transmitted from the Headset Adapter,
received by the Intercom Adapter and output to the aircraft's audio system.
5.2.2
Listening Operation
The Headset Adapter's Phones Volume (VOL) controls the level of audio
heard in the headset's ear phones. As ambient noise levels change, the
volume can be adjusted.
5.2.3
VOX Speaking Operation
To use the JA60 Headset Adapter hands-free, adjust the VOX control so that
the microphone audio is turned on when speaking in to the headset's
microphone at a comfortable level, or at a level to keep the ambient noise
from turning on the microphone audio.
5.2.4
PTT Speaking Operation
To use the JA60 Headset Adapter in high-noise environments, adjust the
VOX control fully clockwise. To communicate, press and hold the JA60
Headset Adapter's PTT button and speak in to the headset's microphone.
5.2.5
Live Speaking Operation
To use the JA60 Headset Adapter so that the microphone audio is always
turned on, adjust the VOX control fully counterclockwise.
5.2.6
Low Battery Warning
When the unit's battery charge is low, the LOW BATT annunciator will triple
flash every 1.5 seconds. When the JA60 Headset Adapter battery charge is
low, a triple-beep will be heard in the headset once every minute.
Note: JAC recommends that the batteries should be charged or
replaced immediately if the LOW BATT warning illuminates during
use.
When the battery charge level is critical, the unit will turn off. When one unit
is off the other unit will begin searching for its paired unit and its PWR ON
annunciator will flash.
Rev C
Page 9
wiJAC-00x Wireless Intercom System
Operating Manual
5.2.7
Operation during Charging
The units will still operate while the Charging Port is connected to a USB
power source, but the batteries will charge at a slower rate. Additional noise
may be heard on the audio system while the Charging Port is connected to a
USB power source.
5.2.8
Loss of Audio
If there is no audio heard in the headset, check the PWR ON annunciator on
the JA60 Headset Adapter and the JA61 Intercom Adapter. If a unit is off,
turn it on and verify connection and operation.
If the battery charge is low, replace or recharge the batteries or connect the
headset directly to the aircraft audio system.
If audio is unintelligible, turn off and remove the JA60 Headset Adapter and
the JA61 Intercom Adapter and connect the headset directly to the audio
panel.
If another aircraft system is experiencing a fault, turn off and remove the
JA60 Headset Adapter and the JA61 Intercom Adapter and connect the
headset directly to the audio panel. Do not use the JA60 Headset Adapter
and the JA61 Intercom Adapter if they appear to be the cause of the fault.
5.2.9
Battery Life
The operating duration of the wiJAC-00x system with fully charged batteries
before battery replacement is required depends on the following factors:
•
Distance between Headset Adapter and Intercom Adapter:
The closer together the units are the lower the radio frequency (RF)
power required for connection. This will increase the battery life.
•
Obstacles between the Headset Adapter and Intercom Adapter
(VOL):
Minimising the aircraft metal structures, human bodies, cargo and other
obstacles between the units will reduce the RF power needed for
connection and increase the battery life.
•
Charge capacity of the batteries installed:
The higher the capacity of the batteries, typically specified as 500 to
1000 mAh (milliamp-hours), the longer the battery life.
•
The type of batteries installed and the operating temperature:
During low temperature operation, rechargeable batteries will lose
capacity. When operating in low temperatures use alkaline batteries for
a longer battery life.
•
The phones volume level and usage rate:
The lower the volume level and the less often audio is output to the
phones, the longer the battery life.
Rev C
Page 10
wiJAC-00x Wireless Intercom System
Operating Manual
6
Batteries
WARNING: Charging battery types other than NiMH or NiCad
may cause the batteries to leak or explode and cause damage
or injury. If non-NiMH or non-NiCad batteries are installed, do
not connect the Charging Port to a USB power source.
The JA60 and JA61 require three AAA batteries. JAC recommends Duracell
800 mAh (or higher) NiMH or Duracell alkaline batteries for use in the
wiJAC™ system to obtain the typical battery life.
Removal of the batteries WILL NOT change any internal configuration of the
unit.
6.1
Inserting or Replacing the Batteries
Retaining tabs
To replace the batteries (both
units the same), remove the
battery cover by pressing the
battery lid release towards the
JAC logo, lifting the lower end of
the cover, and then gently prying
the lid up and away from the
body to release the two tabs from
the retaining slots.
Remove the batteries and insert
fully charged batteries matching
the polarity marked on the battery
holder.
Battery Lid Release
6.2
Charging Batteries in the Unit
To charge rechargeable batteries in the unit, connect the Charging Port to a
USB power source using the USB to Micro-USB cable (CAB-USB-0003). If
turned on during charging, the unit draws its power from the charging
source, not the batteries, but battery charging will take longer. When
charging is complete, the 'Top Off' Charge annunciator will illuminate green.
It should be possible to charge the unit via most USB power sources but this
cannot be guaranteed for any products not made by or purchased from JAC.
Where space allows, JAC recommends the JAC JA72-006 6 Dzus Glove
Box with USB connector (see section 7.1)
Note: The batteries will charge whether the JA60/JA61 is switched
on or switched off. Battery charging will take longer if the unit is
switched on.
Rev C
Page 11
wiJAC-00x Wireless Intercom System
Operating Manual
6.3
Charging Operation – via Battery Charger
The batteries may be removed from the unit for charging in a separate
battery charger. Removal of the batteries WILL NOT change any internal
configuration of the unit.
Note: The JA60 and JA61 will only charge the batteries when the
internal temperature is within 0 to 40 °C
6.4
Battery Cautions and Warnings
CAUTION: Follow these guidelines to prolong battery life and
minimize the risk of unit malfunction.
Do not leave battery uncharged for long periods of time.
Do not leave battery charging for extended periods (more
than 48 hours)
To ensure that the unit functions correctly, insert the new
batteries with the positive and negative poles aligned as
indicated in the battery compartment.
When replacing the batteries, use only new or fully charged
batteries.
Do not mix old and new batteries as this can cause battery
leakage and/or damage to the unit.
Do not mix battery types.
WARNING: Follow these guidelines to prolong battery life,
and minimize the risk of fire, chemical burns, electrolyte leaks
and/or injury.
FOLLOW the manufacturer's instructions for care and
disposal of batteries.
DO NOT use sharp objects to remove the batteries.
DO NOT disassemble, puncture, burn or in any other way
damage the batteries.
DO NOT let children handle the batteries.
USE ONLY recommended battery chargers.
USE ONLY recommended replacement batteries.
Rev C
Page 12
wiJAC-00x Wireless Intercom System
Operating Manual
7
Accessories
7.1
JA72-005 Glove Box with USB connector
The JA72 Glove Box with USB Charger allows the aircraft owner/operator to
utilize an empty portion of the instrument panel for storage.
A USB 2.0 Type A receptacle is provided to supply 5 Vdc power up to 2
Amps, and a 3.5mm stereo jack can be connected to the aircraft's audio
system.
7.2
ProCS™ Product Configuration Software
ProCS™ Product Configuration Software and a ProCS™ connection cable
are available to approved dealers and installers.
7.3
Battery Charger Recommendations
To charge AAA NiMH batteries, JAC recommends the charger should have
individual cell charging (so that three batteries may be charged at once), an
automatic shut-off feature and a charge time of two to six hours.
Always follow the manufacturer’s recommendations for use of batteries and
battery chargers.
Rev C
Page 13
wiJAC-00x Wireless Intercom System
Operating Manual
8
Installation of the JA61 Mounting Bracket
Fig 8-1 - Bracket-mounted JA61
The JA61 Intercom Adapter is
supplied with a mounting bracket
(part number PLT-CLIP-0004)
which may be used to mount the
unit in the aircraft.
The circular mounting clip on the
JA61 slides into the mounting
bracket and clicks into position. It
can be used in any orientation.
Fig 8-2 - Mounting bracket dimensions
The mounting bracket is 1.7" wide by
1.2" high. It is attached using four
screws MS24693 and four locking nuts
MS21044-NO4 through four 1/8"
diameter holes.
Ensure that there is sufficient space to
connect the JA61 to the mounting
bracket and to the aircraft headset jack.
Fig 8-3 - Bracket/jack proximity
Rev C
Fig 8-4 - Mounting details
Page 14
wiJAC-00x Wireless Intercom System
Operating Manual
9
Specifications
9.1
Mechanical
Height
Overall depth
Width
Weight (with Batteries)
Mounting
Headset Connections
Enclosure Material
Configuration Port
Charging Port
9.2
JA60-00x
JA61-00x
4.79 in (122 mm) max
8.15 in (207.0 mm) max
1.10 in (27.9 mm) max
1.10 in (27.9 mm) max
2.05 in (52.1 mm) max
2.05 in (52.1 mm) max
0.39 lb (178 g) max
0.33 lb (149 g) max
Belt clip
Mounting bracket
4 pole TJT-120 jack
4 pole TP-120 plug
Polycarbonate
4 pole 3.5mm jack
USB Micro-AB 2.0
Electrical
JA60-00x
Default MICROPHONE INPUT level
Microphone Type
Default PHONES OUTPUT level
Phones Type
Charging Port
JA61-00x
Default MICROPHONE OUTPUT level
Default PHONES INPUT level
Charging Port
9.3
250 mVrms
150 Ω Amplified Dynamic
4.00 Vrms into 150 Ω
150 Ω
5 Vdc @ 200 mA
300 mVrms
4.50 Vrms into 600 Ω
5 Vdc @ 200 mA
Environmental
JA60-00x
JA61-00x
-15 to +50 °C
25,000 ft
95% RH (48 hours)
6 g, 20g (for 11 ms)
Operating Temperature
Altitude
Humidity
Shock, Crash Safety
9.4
Other
JA60-00x
Battery Life
Battery Quick Charge Duration
Battery Top-Up Charge Duration
Low Battery Notice Duration
Range
Rev C
JA61-00x
6 to 8 h (typical)
4h
48 h max
15 minutes
100 meters (typical)
Page 15
wiJAC-00x Wireless Intercom System
Operating Manual
10
Warranty
Locate and complete the online warranty registration form from the JAC
website: www.jupiteravionics.com/warrantyregistration
These products manufactured by JAC are warranted to be free of defects in
workmanship or performance for 1 year from the date of purchase from an
authorized JAC dealer. This warranty covers the cost of all materials and
labour to repair or replace the unit, but does not include the cost of
transporting the defective unit to and from JAC or its designated warranty
repair centre. This warranty does not cover failures due to abuse, misuse,
accident, incorrect battery use/installation, or unauthorized alteration or
repairs.
Contact JAC for any questions regarding this warranty and how it applies to
your unit(s). JAC is the final arbiter concerning warranty issues.
Contact JAC for a Returned Materials Authorisation Form (RMA) prior to
shipping any products for repair. This form can be downloaded from our
website at www.jupiteravionics.com/dealersrmaform
11
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1.
2.
this device may not cause harmful interference, and
this device must accept any interference received, including interference
that may cause undesired operation of the device.
Module transmetteur ID IC: 9576A-SC14A
Son fonctionnement est soumis aux deux conditions suivantes:
1.
2.
cet appareil ne doit pas causer d’interférences nuisibles et
cet appareil doit accepter toute interférence reçue, y compris les
interférences qui peuvent perturber le fonctionnement.
Changes or modifications to the equipment not expressly approved by the Party
responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and radiates radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. There is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
• Increase the separation between the equipment and the receiver.
• Turn the equipment off and remove from the aircraft audio system. Connect the
headset to the aircraft audio system.
• Consult Jupiter Avionics Corp or an experienced avionics technician for help.
Privacy of communications may not be ensured when using this equipment.
Rev C
Page 16
Jupiter Avionics Corporation
1959 Kirschner Road
Kelowna BC
V1Y 4N7 Canada
Tel: +1 778 478 2232
Toll-Free: 1 855 478 2232
www.jupiteravionics.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising