GH-PSU22-PC
Installation Guide
The cooler fan speed levels provided are for reference use only.
Please refer to the motherboard BIOS to verify actual fan speed levels.
The followings are not covered by the warranty :
1. Use the product incorrectly or in a manner other than the designed purpose.
2. Nonobservance of the proper operation. ( e.g. over-clocking )
3. Malfunction due to interference from other devices.
4. Unauthorized modification of the product.
5. Malfunction due to unfit specifications on Motherboard.
6. Malfunction arising from casualties ( earthquake, thunder, fire, and flood ).
7. The product’s warranty label has been removed or damaged.
8. The devices inside, including power supply, hard disk, CD-ROM drive,
motherboard, cooler, etc, are not detached from the chassis prior to the
transportation of the computer product, resulting in damage to the cooler
or computer-related devices.
9. Any damage caused by nonobservance of the installation instruction contained
in this manual.
Features
1. Universal design, supports LGA775 & AMD K8 / AM2 platform.
2. Curve design combines CPU and MOSFEAT cooling together.
3. 9CM silent fan with PWM function, highest fan speed can reach 2300RPM.
4. Highly heat conducting heat pipe, provides extreme cooling performance.
5. Pure copper base with aluminum fin, extra large heat dissipation area allows heat been carried away faster.
6. Hassle-free installation.
Specification
Dimension : 102 x 122 x 139 mm
Fan Dimension : 90 x 90 x 25 mm
Heat Pipe : 3
Base Material: Copper
Fin Material : Aluminum
Rated Voltage : 12 V
Rated Current : 0.2 Amp
Fan Speed : 2,300 rpm
Noise Level : 25dBA
Bearing Type : EBR
Fan Life Expectancy : 30,000 hr
Accessories
Compatible CPU
Intel ® Core
TM
2 Extreme Processor Series
Intel ® Core TM 2 Quad Processor Series
Intel
Intel
Intel
®
®
®
Core TM 2 Duo Processor Series
Pentium
Pentium
® Extreme Edition Series
® D Processor Series
Intel ® Pentium
AMD AM2
® 4 Processor Series (LGA775)
AMD Athlon TM FX Series
AMD Athlon
TM
64x2 Series
AMD Athlon TM 64 Series
AMD Sempron Series
AMD K8 / AM2 Clip AM2/K8 Bracket LGA775 Bracket screws x 2 Thermal grease
LGA 775 Platform Installation
STEP 1 STEP 2
Apply some thermal grease on the CPU properly.
Caution :
Before installation, please turn off the power, unplug the power cord, and be sure to remove the sticker from the bottom of the cooler unit.
STEP 3
Before installation, please make sure the pin is on the right direction. (as Figure A)
Place the 775 bracket between the copper base and the cooler unit.
Align the holes of the bracket with the holes of the copper base. Secure the 775 bracket with supplied bracket screws. Make sure the screws are evenly and firmly fastened.
To remove the cooler, turn the four pins to the removing direction and pull them up.(as Figure B)
Figure A Figure B
STEP 4
Align the pin of the cooler with the hole of the CPU on the motherboard and push down the pin diagonally.
Please make sure the four pins are firmly secured.
STEP 5
AMD K8 / AM2 Platform Installation
STEP 1 STEP 2
Apply some thermal grease on the CPU properly.
Caution :
Before installation, please turn off the power, unplug the power cord, and be sure to remove the sticker from the bottom of the cooler unit.
Plug the 4-pin connector of the cooler into the motherboard’s CPU fan socket.
Place the AM2/K8 Bracket between the copper base and the cooler unit.
Align the holes of the bracket with the holes of the copper base. Secure the AM2/K8 Bracket with supplied bracket screws. Make sure the screws are evenly and firmly fastened.
STEP 3
Lock the tab on one side of AMD
K8 / AM2 clip in the salient point of the CPU cooler.
STEP 4
Lock the tab on the other side of
AMD K8 / AM2 clip in the salient point of the CPU cooler bracket; push down and secure the bar on the clip firmly.
STEP 5
Plug the 4-pin connector of the cooler into the motherboard’s
CPU fan socket.
