View the Installation Instructions

View the Installation Instructions
Accessory
INSTALLATION
INSTRUCTIONS
Application
Publications No.
AII 27159
CR-V
FRONT ASHTRAY
PARTS LIST
Issue Date
AUG 2004
3.
Front ashtray
Remove the driver’s dashboard under cover by
turning the knob clockwise, and releasing one
clip.
HOLDER
Self-tapping screw
Illumination harness
CLIP
4.
4 Wire ties
TOOLS REQUIRED
Phillips screwdriver
Stubby Phillips screwdriver
Small flat-tip screwdriver
KNOB
Turn
clockwise
90°.
DRIVER’S DASHBOARD
UNDER COVER
Remove the driver’s dashboard lower cover:
•
Remove the fuse box lid, and open the pocket.
•
Remove the two self-tapping screws.
•
Gently pull out on the driver’s dashboard lower
cover to release the eight clips. If equipped,
unplug the vehicle connector and remove the
lower cover.
VEHICLE
CONNECTOR
(If equipped.)
INSTALLATION
DRIVER’S
DASHBOARD
LOWER
COVER
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures
should not be attempted by “do-it-yourselfers.”
1.
Make sure you have the anti-theft code for the
radio, then write down the radio station presets.
2.
Disconnect the negative cable from the battery.
VEHICLE
CONNECTOR
(If equipped.)
HOOKS (2)
FUSE
BOX
LID
POCKET
SELFTAPPING
SCREW
CLIPS (8)
RETAINING
TABS (2)
CLIP
4130110H
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
AII 27159 (0409)
08U25-S9A-1002-91
1 of 4
5.
Remove the passenger’s dashboard under cover
(release the three clips and two pins).
8.
Remove the heater A/C control panel (two selftapping screws, and unplug the connector).
SELFTAPPING
SCREW
CLIPS (3)
HEATER A/C
CONTROL
PANEL
PASSENGER’S
DASHBOARD
UNDER
COVER
VEHICLE
CONNECTOR
CLIPS (4)
4130130H
PINS (2)
6.
9.
Open the dashboard pocket lid. Remove the lid
(two retaining clips, and two retaining tabs).
On A/T vehicles only, remove the dashboard
center lower cover (two clips, six retaining clips
and unplug the 2-pin connector).
RETAINING TAB
CLIP
DASHBOARD
POCKET
SELFTAPPING
SCREWS (6)
VEHICLE 2-PIN
CONNECTOR
SELFTAPPING
SCREW
LID
RETAINING
CLIPS (2)
4130121H
RETAINING
TABS (2)
DASHBOARD
CENTER
LOWER
COVER
RETAINING VEHICLE
CONNECTOR
TABS (2)
DASHBOARD
POCKET LID
Pull
CLIPS (2)
RETAINING
CLIPS (4)
7. Remove the dashboard pocket (one self-tapping
screw, one clip, three retaining tags and unplug
the vehicle connector).
2 of 4
4404301T
RETAINING
CLIP
AII 27159 (0409)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
10. Remove the beverage holder by pulling it out
toward you while pushing down on its two retaining
tabs.
12. Remove the bracket from the ashtray, then install
the bracket on the dashboard center lower cover
using the two self-tapping screws you just
removed and one self-tapping screw supplied.
Push.
SELFTAPPING
SCREW
(Supplied.)
BRACKET
RETAINING
TAB
DASHBOARD
CENTER LOWER
COVER
SELFTAPPING
SCREW
(reused)
BEVERAGE
HOLDER
DASHBOARD
CENTER
LOWER
COVER
ASHTRAY
13. Slide the ashtray into position in the cover.
11. Remove the beverage holder bracket (four selftapping screws).
14. Unplug the vehicle 6-pin connector from the fuse
box, and connect the 6-pin connectors of the
illumination harness in between.
VEHICLE 6-PIN
CONNECTOR
FUSE
BOX
SELFTAPPING
SCREWS
(Discard.)
SELF-TAPPING
SCREWS
(reused)
ILLUMINATION
HARNESS 6-PIN
CONNECTORS
ILLUMINATION
HARNESS
BEVERAGE
HOLDER
BRACKET
(Discard.)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
VEHICLE
HARNESS
DASHBOARD
OPENING
AII 27159 (0409)
3 of 4
15. Route the illumination harness to the dashboard
opening along the vehicle harness.
17. Remove the illumination bulb cap from the
illumination bulb, then insert the illumination bulb
into the ashtray, and secure the bulb by turning it
in the direction shown.
NOTE: If you are also installing the fog lights,
unplug the vehicle 6-pin connector from the fuse
box, and then plug it into the 6-pin connector
black-taped to the fog light switch harness. Plug
the other 6-pin connector of the fog light switch
harness into the 6-pin connector black-taped to
the illumination harness. Finally, plug in the
remaining 6-pin connector of the illumination
harness into the fuse box.
ASHTRAY
6-PIN CONNECTOR
of FUSE BOX
VEHICLE’S 6-PIN
CONNECTOR
6-PIN
CONNECTORS of
ILLUMINATION
HARNESS
ILLUMINATION
BULB
ILLUMINATION
BULB CAP
(Discard.)
6-PIN CONNECTORS
of FOG LIGHT
SWITCH HARNESS
16. Secure the illumination harness to the vehicle
harness with four wire ties.
FUSE BOX
VEHICLE
HARNESS
18. Reinstall the dashboard center lower cover.
19. Reinstall all removed parts.
20. Check that all wire harnesses are routed properly
and all connectors are plugged in.
21. Reconnect the negative cable to the battery.
22. Enter the customer’s radio anti-theft code, and
reset the radio station presets.
23. Reset the clock.
NOTE: Whenever the battery is disconnected, the
driver’s AUTO function is disabled.
ILLUMINATION
HARNESS
WIRE TIES
24. Start the engine. Push down on the driver’s
window switch until the window is fully open.
25. Pull up on the driver’s window switch to close the
window completely, then hold the switch for at
least two seconds.
26. Test the AUTO window function.
4 of 4
AII 27159 (0409)
© 2004 American Honda Motor Co., Inc - All Rights Reserved.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement