Start-Up Guide SINUMERIK 840D/810D, SIMODRIVE 611 digital

Add to my manuals
298 Pages

advertisement

Start-Up Guide SINUMERIK 840D/810D, SIMODRIVE 611 digital | Manualzz
SINUMERIK 840D/810D
SIMODRIVE 611 digital
Start-Up Guide
General preparation
1
Structure
2
Settings, MPI/BTSS
3
EMC/ESD measures
4
Power-On and Power-Up
5
Programming the
control
6
PLC description
7
Alarm and message texts
8
Axis/spindle test run
9
Drive optimization
10
Data back-up
11
Replacing software and
hardware
12
HMI
13
Miscellaneous
14
Valid for
Control
Version
SINUMERIK 840D/810D powerline
6
SINUMERIK 840DE/810DE powerline
(export variant)
6
Drive
Version
SIMODRIVE 611 digital
5
03/2006 Edition
Abbreviations
Index
A
3ls
SINUMERIK® documentation
Key to editions
The editions listed below have appeared before this edition.
The letters in the “Note” column indicate which status the previously published editions have.
Identification of the status in the “Notes” column:
A . . . . . New documentation.
B . . . . . Unchanged reprint with new order number.
C . . . . . Revised version with new edition number.
Edition
03/2006
Order no.
6FC5 297-6AB20-0BP0
Notes
A
Trademarks
®
All designations identified with the trademark note are registered trademarks of Siemens AG. The other
designations in this publications may be trademarks, the use of which by third parties for their own
purposes may infringe the rights of the owner.
Exclusion of liability
We have checked the content of the document to ensure that it conforms to the described hardware and software. Nevertheless, the possibility of differences cannot be totally excluded, so we are unable to guarantee that
it conforms totally. However, the information in this document is checked regularly and necessary corrections
are included in the subsequent editions.
Copyright Siemens AG 2006
Order no: 6FC5297-6AB20-0BP0
Siemens AG 2006
Subject to technical modifications.
Preface
Structure of the
documentation
The SINUMERIK documentation is divided into three levels:
S General documentation
S User documentation
S Manufacturer/service documentation
A monthly updated list of publications with the available language versions can
be found on the Internet at:
http://www.siemens.com/motioncontrol
Follow the menu options “Support” → “Technical Documentation” → “List of
Publications”.
The Internet edition of the DOConCD – the DOConWEB – can be found at:
http://www.automation.siemens.com/doconweb
Information about training courses and FAQs (frequently-asked questions) can
be found on the Internet at:
http://www.siemens.com/motioncontrol , select the “Support” option.
Target group
This documentation is intended for use by start-up engineers.
Benefits
The Start-Up Guide will enable the intended target group to test the product/
system or plant and to bring it into service correctly and safely.
Standard scope
This Start-Up Guide describes the functionality of the standard scope. Additions
or modifications made by the machine manufacturer will be documented by the
machine manufacturer.
Other functions not explained in this document may also run on the control.
However, no claims to these functions exist in the event of replacement and/or
maintenance.
For the sake of clarity, this documentation does not contain all the detailed information about all types of the product, and also cannot take account of every
possible situation for installation, operation and maintenance.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
iii
03/2006
Preface
Technical Support
If you have any questions, please contact the following hotline:
Europe and Africa time zones:
A&D Technical Support
Tel.: +49 (0) 180 / 5050 – 222
Fax: +49 (0) 180 / 5050 – 223
Internet:
http://www.siemens.com/automation/support-request
E-Mail:
mailto:[email protected]
Asia and Australia time zones:
A&D Technical Support
Tel.: +86 1064 719 990
Fax: +86 1064 747 474
Internet:
http://www.siemens.com/automation/support-request
E-Mail:
mailto:[email protected]
America time zone:
A&D Technical Support
Tel.: +1 423 262 2522
Fax: +1 423 262 2289
Internet:
http://www.siemens.com/automation/support-request
E-Mail:
mailto:[email protected]
Note
Country-specific telephone numbers for technical advice can be found on the
Internet:
http://www.siemens.com/automation/service&support
Questions about
this Guide
If you have any questions about the documentation (suggestions or corrections), please send a fax or e-mail to the following address:
Fax: +49 (0) 9131 / 98 – 63315
E-Mail: mailto:[email protected]
Fax form: see Feedback sheet at the end of this document.
SINUMERIK
web site
http://www.siemens.com/sinumerik
EU Declaration of
Conformity
The EU Declaration of Conformity about the EMC Directive can be found/
obtained
S on the Internet:
http://www.ad.siemens.com/csinfo
under product/order number 15257461
S from the responsible branch of the A&D MC Division of Siemens AG
Object of the book
iv
The publication illustrates the structure of the control system and the interfaces
to the individual components. It also describes the procedure for starting up
SINUMERIK 810D, and lists all the data, signals and PLC modules.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Preface
03/2006
User-oriented activities such as the creation of part programs and control
operation procedures are described in detail in separate documents.
Separate descriptions are likewise provided for the tasks to be performed by the
tool manufacturer such as configuring, installation and PLC programming.
Safety instructions
!
!
!
This manual contains instructions that you must follow to ensure your own personal safety and to avoid damage to property. The instructions that concern
your personal safety are indicated by a warning triangle. Instructions that concern only damage to property have no warning triangle. The warnings labels are
illustrated in descending order according to the level of risk.
Danger
means that death or severe injury will occur if the specified precautionary
measures are not taken.
Warning
means that death or severe injury may occur if the specified precautionary
measures are not taken.
Caution
with warning triangle means that slight injury may occur if the specified precautionary measures are not taken.
Caution
without a warning triangle means that damage to property may occur if the
specified precautionary measures are not taken.
Notice
means that an unwanted result or state may occur if the specified instructions
are not followed.
If several levels of risk apply, the warning instructions always indicate the
highest level. If a warning of personal injury is given in a warning notice with the
warning triangle, there may also be a warning about damage to property in the
same warning notice.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
v
03/2006
Preface
Qualified
personnel
The associated device/system must only be set up and operated in conjunction
with this documentation. A device/system must only be brought into service and
operated by qualified personnel. Qualified personnel as specified in the safety
instructions in this documentation are people who are authorized to bring into
service, earth and identify devices, systems and power circuits in accordance
with the recognized safety standards.
Use as prescribed
Please note the following points:
!
Warning
The device must only be used for the purposes described in the catalog and in
the technical description, and then only in conjunction with non-Siemens devices and components that are recommended or approved by Siemens. Correct
and safe operation of the product requires it to have been transported, stored,
installed and assembled correctly and carefully operated and maintained.
Further notes
Note
The “Note” symbol is displayed in this document to draw your attention to information relevant to the subject.
Technical information
Notations
The following notations and abbreviations are used in this documentation:
S PLC interface signals –> NST “signal name” (signal data)
Examples:
–
IS “MMC CPU1 ready” (DB10, DBX108.2), i.e. the signal is stored in data
block 10, data byte 108, bit 2.
–
IS “Feedrate override” (DB31, ... DBB0), i.e. the signals are stored in
data blocks 31 to 38, data block byte 0.
S Machine data –> MD: NUMMER, MD_NAME (German designation)
S Setting data –> SD: NUMMER, SD_NAME (German designation)
S The character “8” means “corresponds to”.
J
vi
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Contents
1
General preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-13
1.1
Preconditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-13
1.2
Standard/export variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-14
2
Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-17
3
Settings, MPI/BTSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-19
3.1
3.1.1
MPI network rules for SINUMERIK 840D . . . . . . . . . . . . . . . . . . . . . . . .
Communication equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-19
3-21
3.2
MPI network rules for SINUMERIK 810D . . . . . . . . . . . . . . . . . . . . . . . .
3-24
3.3
MPI default configuration for SINUMERIK 840D . . . . . . . . . . . . . . . . . .
3-26
3.4
MPI default configuration for SINUMERIK 810D . . . . . . . . . . . . . . . . . .
3-28
3.5
Deviation from standard configuration . . . . . . . . . . . . . . . . . . . . . . . . . .
3-30
3.6
MPI interface for customer’s operating panel . . . . . . . . . . . . . . . . . . . .
3-31
3.7
2nd machine control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-32
3.8
3.8.1
3.8.2
PCU 20/50/50.3/70 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings with HMI Embedded/HMI Advanced for SINUMERIK 840D
Settings with HMI Embedded/HMI Advanced for SINUMERIK 810D
3-33
3-33
3-34
EMC and ESD Measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-35
4.1
RI suppression measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-35
4.2
ESD measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-36
4.3
Heat dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-36
Power-On and Power-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-37
5.1
Start-up order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-37
5.2
NCU controls and displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-38
5.3
CCU controls and displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-39
5.4
5.4.1
5.4.2
5.4.3
5.4.4
5.4.5
5.4.6
5.4.7
Power-On and Power-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCU power-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error while Control power-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-up of machine control panel (MSTT) . . . . . . . . . . . . . . . . . . . . .
Powering up the drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PCU/HMI Advanced BIOS setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-40
5-40
5-41
5-44
5-45
5-46
5-46
5-47
4
5
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
vii
03/2006
Contents
6
viii
Programming the control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-49
6.1
Machine and setting data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-49
6.2
Handling machine and setting data . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-52
6.3
6.3.1
6.3.2
Protection level concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Protection levels for NC language commands (REDEF) . . . . . . . . . . .
Configurable parameter areas for GUD blocks . . . . . . . . . . . . . . . . . . .
6-53
6-55
6-57
6.4
6.4.1
6.4.2
Display filter for machine data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting and setting the display filter . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-61
6-61
6-61
6.5
Example of a start-up concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-64
6.6
6.6.1
System data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-67
6-67
6.7
6.7.1
6.7.2
Memory configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dynamic RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Static RAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-71
6-73
6-73
6.8
Scaling machine data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-76
6.9
6.9.1
6.9.2
6.9.3
6.9.4
6.9.5
6.9.6
6.9.7
6.9.8
6.9.9
6.9.10
6.9.11
6.9.12
6.9.13
6.9.14
6.9.15
6.9.16
6.9.17
6.9.18
6.9.19
6.9.20
Axes and spindles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Description of the axis configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drive configuration (VSA, SLM, HSA) . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming axis-specific setpoint/actual values . . . . . . . . . . . . . . . .
Setting drive parameters (FDD, MSD) . . . . . . . . . . . . . . . . . . . . . . . . . .
Parameter settings for incremental measuring systems . . . . . . . . . . .
Parameter settings for absolute measuring systems (EnDat interface)
Overview of the drive parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Axis data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Axis velocity matching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Axis position control data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Monitoring for axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Referencing an axis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spindle data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spindle configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spindle encoder matching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Velocities and setpoint matching for spindles . . . . . . . . . . . . . . . . . . . .
Spindle positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spindle synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Spindle monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Example: Starting up NCK I/Os . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-78
6-78
6-82
6-85
6-87
6-89
6-92
6-95
6-99
6-102
6-103
6-108
6-113
6-115
6-117
6-118
6-120
6-122
6-123
6-125
6-127
6.10
6.10.1
6.10.2
6.10.3
6.10.4
6.10.5
6.10.6
6.10.7
6.10.8
Linear motors (1FN1 and 1FN3 motors) . . . . . . . . . . . . . . . . . . . . . . . . .
General information for starting up linear motors . . . . . . . . . . . . . . . . .
Start-up: linear motor with a primary section . . . . . . . . . . . . . . . . . . . . .
Start-up: linear motors with 2 identical primary sections . . . . . . . . . . .
Mechanical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Temperature sensors for 1FN1 and 1FN3 motors . . . . . . . . . . . . . . . .
Measuring system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parallel connection of linear motors . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test measurements on linear motors . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-129
6-129
6-131
6-141
6-143
6-144
6-147
6-150
6-152
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Contents
03/2006
7
8
9
10
6.11
AM/U/F function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-154
6.12
System settings for power-up, RESET and starting part programs . .
6-155
PLC Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-159
7.1
PLC start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-159
7.2
Overview of the organizational blocks, function blocks, DBs . . . . . . .
7-162
Alarm and message texts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-163
8.1
Alarm text files for HMI Embedded . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-163
8.2
Alarm text files for HMI Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-164
8.3
8.3.1
Syntax for alarm text files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Alarm list properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8-167
8-169
Axis/Spindle Dry Run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-171
9.1
Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-171
9.2
Axis dry run . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-173
9.3
Test of the spindle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9-175
Drive Optimization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-177
10.1
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-177
10.2
Measuring functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-179
10.3
Interface signals: Drive test travel request and Travel enable . . . . . .
10-182
10.4
10.4.1
10.4.2
10.4.3
Frequency response measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scanning the torque control loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scanning the speed control loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scanning position control loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-183
10-183
10-184
10-188
10.5
10.5.1
10.5.2
Measuring function for coupled axes . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interconnected gantry axes only or master–slave couplings . . . . . . . .
Mixed couplings of master/slave and gantry axes . . . . . . . . . . . . . . . .
10-191
10-191
10-193
10.6
10.6.1
Graphical display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Associated conditions for gantry axes . . . . . . . . . . . . . . . . . . . . . . . . . .
10-194
10-195
10.7
10.7.1
10.7.2
10.7.3
10.7.4
10.7.5
10.7.6
Trace function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Main screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Programming and activating measurements . . . . . . . . . . . . . . . . . . . . .
Display function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display bit graph for SI signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
File functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Print graph . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-196
10-198
10-198
10-202
10-205
10-213
10-215
10.8
Analog output (DAC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10-216
10.9
10.9.1
10.9.2
Automatic controller settings ( HMI Advanced only) . . . . . . . . . . . . . . .
Flowchart for self-optimization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input possibilities for self-optimization . . . . . . . . . . . . . . . . . . . . . . . . . .
10-217
10-219
10-223
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
ix
03/2006
Contents
11
12
x
Data Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-227
11.1
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-227
11.2
Data back-up via HMI Embedded . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-229
11.3
Data back-up via HMI Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-229
11.4
Data back-up via PG/PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-229
11.5
11.5.1
Data back-up via machine data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard system start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-231
11-233
11.6
Data back-up via V24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-236
11.7
11.7.1
11.7.2
11.7.3
11.7.4
11.7.5
Data output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outputting the drive data via V24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outputting the NC data via V24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outputting the PLC data via V24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outputting the HMI data via V24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Outputting the standard system start-up file via V24 . . . . . . . . . . . . . .
11-239
11-239
11-240
11-242
11-243
11-244
11.8
11.8.1
11.8.2
11.8.3
11.8.4
Backing up the hard disk with Norton GhostR . . . . . . . . . . . . . . . . . . . .
Hard disk backup/restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Saving user data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Backing up the hard disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Copy data to hard disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-245
11-245
11-247
11-247
11-249
11.9
Backing up the current image of the latest software . . . . . . . . . . . . . . .
11-251
11.10
Installing a replacement hard disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-253
11.11
Data back-up with VALITEK streamer with the PCU 50 . . . . . . . . . . .
11-255
11.12
11.12.1
11.12.2
11.12.3
Line checksums and MD numbers in MD files . . . . . . . . . . . . . . . . . . .
Line checksums (MD 11230 MD_FILE_STYLE) . . . . . . . . . . . . . . . . . .
Machine data numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Response to canceling while reading in machine data . . . . . . . . . . . . .
11-260
11-260
11-261
11-261
11.13
Machine/setting data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-263
11.14
Back up PLC data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11-264
Replacing software and hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-265
12.1
12.1.1
Software update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-265
12-266
12.2
Software upgrade for HMI Embedded . . . . . . . . . . . . . . . . . . . . . . . . . .
12-267
12.3
Software upgrade for HMI Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-267
12.4
12.4.1
12.4.2
12.4.3
Standard system start-up via NC card . . . . . . . . . . . . . . . . . . . . . . . . . .
DRAM for storing cycles and programs . . . . . . . . . . . . . . . . . . . . . . . . .
SINUCOPY-FFS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Associated conditions for replacing software . . . . . . . . . . . . . . . . . . . . .
12-267
12-269
12-272
12-276
12.5
Hardware replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-277
12.6
Replacing batteries and fans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12-277
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Contents
03/2006
13
HMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13-279
14
Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14-281
14.1
14.1.1
14.1.2
Tool box software package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents of the tool box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application of the Tool box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14-281
14-281
14-281
14.2
Machine data access via part program . . . . . . . . . . . . . . . . . . . . . . . . . .
14-282
A
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A-285
B
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Index-291
J
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
xi
03/2006
Contents
Notes
xii
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
1
General preparation
1.1
1
Preconditions
Introduction
This Installation and Start-Up Guide describes the procedure for starting up the
basic control functions including drive-related functions. Further reference material on special NCK, HMI, PLC or drive functions can be found in the Function
Descriptions/Manuals (see “Documentation required”).
Software required
You will need the following software for starting up the SINUMERIK 840D:
1. SinuComNC start-up/service tools
Supplied on CD-ROM with:
–
SinuCom NC
–
SinuCom FFS
–
SinuCom ARC
–
SinuCom PCIN
–
Start-up tool
2. SIMATIC Step7
3. Tool-Box for SINUMERIK powerline with:
–
Basic PLC program
–
NC variable selector
–
Sample programs
4. For HMI Embedded, application diskette or CompactFlash card for creating
PLC alarm texts and transferring them to the PCU (supplied with the HMI
system software).
Required devices
and accessories
You will need the following devices and accessories for starting up the
SINUMERIK 840D:
1. PC/PG for SinuComNC start-up/service tools and SIMATIC Step7
2. MPI cable for PC/PG
3. V24 cable with 9-pin connector (socket)
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
1-13
03/2006
1 General Preparation
1.2 Standard/export variants
1
Documentation
required
You will need the following documentation for starting up the SINUMERIK 840D.
A detailed description of the mechanical and electrical structure of the individual
components can be found in:
1. /BU/ Catalog of automation systems for machine tools
2. /PHD/ Device Manual, NCU Configuration
SINUMERIK 840D
3. /PHC/ Device Manual, CCU Configuration
SINUMERIK 810D
4. /PJU/ Converter Configuration Manual
SIMODRIVE 611 digital
5. /BH/ Device Manual, Operating Components
SINUMERIK 840D/840Di/810D
6. /FB1/ Function Guide for Basic Machine
7. /FBA/ Function Guide for Drive Functions
8. /LIS1/ Lists
9. /PI/PCIN Description
10. /DA/ Diagnostic Instructions
11. /IAM/ HMI Start-up Guide
1.2
Standard/export variants
Export permits
required
2 variants of the SINUMERIK 840D/810D can be configured due to the
requirement to obtain approval for certain control functions as listed in the
German export list.
The standard variant (840D/810D) can contain the full range of functions of the
control, but is therefore subject to the requirement to obtain approval.
With the export variant (840DE810DE), certain options are not available.
Current information about the type and scope of the options is contained in
Reference material: /BU/ Catalog of automation systems for machine tools
(This shall not affect any requirement to obtain approval with respect to the
intended usage which may also arise).
The specific version of the control is determined by the system software, which
is thus available in two variants (standard and export). This means that the
requirement to obtain approval for the system software (further information may
be given on the delivery note or invoice) is ’inherited’ when it is installed on the
control system. This point should be noted, particularly for conversions/
upgrades of the system software, since this may change the requirement to
obtain export approval for the control.
1-14
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
1.2
Identification of
the control
1 General Preparation
Standard/export variants
The hardware components supplied with system software are, in addition to any
information on the delivery note and invoice, clearly identified by as standard or
export variants by means of stickers.
Note
The additional stickers supplied in the packaging are intended to identify the
control after start-up, and should be stuck into the control’s logbook. When
licenses are ordered, a corresponding number of stickers is supplied. These
should be used in the same way.
Once the control has powered up, the export variant can be identified by the
additional letter ‘E’ on the Service screen (NCK information). It is important for
Service to be able to identify the control variant in this way. It can also serve to
provide the necessary verification for exports, particularly if existing negative
certificates for the export variant are used.
J
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
1-15
1
1 General Preparation
1.2 Standard/export variants
1
03/2006
Notes
1-16
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
2
Structure
Reference material
A detailed description of the mechanical and electrical structure can be found in
the following documents:
S /PHD/ Device Manual, NCU Configuration
SINUMERIK 840D
S /PHC/ Device Manual, CCU Configuration
SINUMERIK 810D
S /PJU/ Converter Configuration Manual
SIMODRIVE 611 digital
S /BH/ Device Manual, Operating Components
SINUMERIK 840D/840Di/810D
J
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
2-17
2
03/2006
2 Structure
Notes
2
2-18
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Settings, MPI/BTSS
3.1
3
MPI network rules for SINUMERIK 840D
The following basic rules should be followed when installing a network.
1. The bus line must be terminated at both ends. To do this, activate the terminating resistor in the MPI connector of the first and last node,and deactivate
the remaining terminating resistors.
Note
S Only two resistors are permissible.
S With HHU, bus terminating resistors are hard-wired into the device.
2. There must be at least 1 termination at the supply voltage. This occurs automatically when the MPI connector with active terminating resistor is connected to a live device.
3. Spur lines (lead cables from the bus segment to the node) should be as
short as possible.
Note
Any spur lines that are not assigned should be removed if possible.
4. Each MPI node must be connected before being activated. When an MPI
node is disconnected, the connection must be deactivated before the connector can be pulled out.
5. One or two HHU may be connected per bus segment. No bus terminators
may be connected to the distributor boxes of an HHU. If necessary, an intermediate repeater can be used to connect more than one HHU to a bus segment.
6. The following cable lengths for the standard MPI without repeater must not
be exceeded:
MPI (187.5 kBaud): max. total cable length 1000 m
Note
Piggy-back connectors are not recommended for power connections.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
3-19
3
03/2006
3 Settings, MPI/BTSS
3.1 MPI network rules for SINUMERIK 840D
Example A
ËËË
ËËË
ËËËËË
ËËË
ËËËËË
ËËËËËË
ËËË
ËËËËË
ËËË
ËËËËËË
ËËËËË ËËËËËËË
ËËËËËËË
ËËËËËËË
ËËËËËËË
ËËËËËËË
ËËËËË
ËËËËË
ËËËËË
ËËËËË
on
HHU
Terminating resistor
fitted in connector
on
PCU
Distributor
box
3
on
MSTT
Terminating resistor
hard-wired
on
BTSS
Control 840D
MPI
on
PG
Fig. 3-1
Example B
Network installation with two terminating resistors in
MPI: PG, control 840D
BTSS: HHU, control 840D
ËËËËËË
ËËËË
ËËËËËË
ËËËË
ËËËË
ËËËËËË
ËËËË
ËËËË
ËËËËËË
ËËËËËËËËËËËËËË
ËËËËËËË
ËËËËËËË
ËËËËËËË
ËËËËËËË
ËËËËËËË
on
Terminating resistor
fitted in connector
OP030
PCU
on
MSTT
Terminating resistor
hard-wired
on
on
BTSS
Control 840D
Fig. 3-2
3-20
Network installation with two terminating resistors in BTSS:
MSTT, control 840D
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
3 Settings, MPI/BTSS
MPI network rules for SINUMERIK 840D
03/2006
3.1
3.1.1
Communication equipment
The components involved in MPI and BTSS communication are PLC, NCK,
COM and PCU/HMI. They allow communication between the active nodes.
Communication between passive nodes, e.g. GD circuit communication, is not
discussed here.
The aforementioned component perform the following tasks concerning MPI
and BTSS communication:
S PLC and NCK
PLC and NCK are both servers that provide communication links to client
components and execute jobs via these client components upon request.
The number of possible communication links from the server to the clients
and the number of parallel function jobs (Read variables, Write variables,
etc.) are limited.
S HMI
An HMI component is a client that requests communication links from one or
more servers and sends jobs to them.
S COM
The COM component is a router that allows communication between various component via different communication links (MPI, BTSS and Dual
Port RAM).
HMI (client)
Machine control panel
(passive GD circuit node)
SINUMERIK 840D
COM (router)
6
BTSS bus (1.5 MBaud)
SIMATIC
programming device
X101
DPR
1
Router
13
HMI (client)
NCK
(server)
3
PLC (server)
0
1
X122
2
Router
MPI bus (187 5 kBaud)
X102
Default bus addresses
Fig. 3-3
PROFIBUS DP (12 MBaud)
Default application for SINUMERIK 840D
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
3-21
3
03/2006
3 Settings, MPI/BTSS
3.1 MPI network rules for SINUMERIK 840D
HMI communication: BTSS bus
An HMI component logs on onto the NCK and PLC servers as a client via the
COM module and is allocated communication resources by them as a result of
logging on.
Jobs with a bus address/job ID for NCK are routed by the COM module directly
to the NCK. Jobs with different bus addresses/job IDs are routed to the PLC.
This response is implicit routing, and no special routing information is required
in the COM module about other communication nodes on adjacent bus
systems.
3
HMI communication: MPI bus
An HMI component logs onto the NCK server as a client indirectly via the COM
module and directly at the server PLC is allocated communication resources by
them as a result of logging on.
Jobs with a bus address/job ID for NCK are routed by the COM module directly
to the NCK. Jobs with different bus addresses/job IDs are ignored by the COM
module. This response is also implicit routing, and no special routing information
is required in the COM module about other communication nodes on adjacent
bus systems.
Associated conditions for STEP 7
It is not possible to configure the entire communication setup illustrated in
Fig. 3-3 in SIMATIC STEP7. Thus, STEP7 and any other engineering tools will
not provide all the possible communication links. In particular, the COM module
that acts as the link between the MPI and BTSS buses cannot be configured.
Logon IDs
When a connection is established, a client component logs onto the PLC with its
logon ID. Typical logon IDs include programming device: “PG” and operator
panel: “OP”. One communication link on the PLC is reserved for a component
with the logon ID “PG” and one for the “OP” logon ID. For historical reasons, an
HMI component with the logon ID: “PG” by default. For the “M to N” function, it
logs on with the logon ID: “OP”.
Communication
links
The NCK, COM and PLC components allow the following maximum number of
possible communication links:
Component
Number
NCK
5
COM
from BTSS bus to NCK
3
from BTSS bus to PLC
3
from MPI bus to NCK
3
PLC
1)
PLC 315-2DP (contained in: CCU3 and NCU*.3)
4
PLC 314C-2DP (contained in NCU*.4)
12
PLC 317-2DP (contained in NCU*.5)
32
from MPI bus to PLC
2)
1) One communication link is reserved by default for connecting a programming device
(PG) e.g. for diagnostics with STEP7.
2) The number results from the maximum number of PLCs integrated into the NCU,
minus the active PLC communication links on the BTSS bus.
3-22
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
3.1
3 Settings, MPI/BTSS
MPI network rules for SINUMERIK 840D
Each client component requires the following communication links for communication with the NCK and PLC servers:
Component
Number
HMI Advanced or HMI Embedded
To NCK
1
To PLC
1
3
Shopmill/Shopturn on HMI Advanced or HMI Embedded
To NCK 1)
+1
1)
+1
To PLC
STEP 7 on HMI
To PLC 1)
+1
1) In addition to the HMI communication link
Note
A Protool configuration does not need an additional communication link for
ProtoolPro with the “SINUMERIK” option.
Equipment
required
Table 3-1
The following tables illustrate the communication equipment required for the
individual components: NCK, PLC and COM
NCK equipment required
Resource unit
Machine data
Max. number of HMI resource units 1)
10
$MN_MM_NUM_MMC_UNITS
1) HMI Embedded and HMI Advanced require 2 resource units per communication link.
Table 3-2
PLC equipment required
PLC 314
PLC 315-2AF00
PLC 315-2AF01
PLC 315-2AF03
PLC 314C-2DP
PLC 317-2DP
Communication links
max. possible number
4
4
4
4
12
32
Reserved for programming device
1
1
1
1
1
1
Available for HMI components
3
3
3
3
11
31
Table 3-3
COM equipment required
PLC
NCK
Links 1)
BTSS bus: max. possible number
3
3
MPI bus: max. possible number
1)
3
1) Note: The MPI links are not routed via the COM module. They go directly to the PLC.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
3-23
3 Settings, MPI/BTSS
3.2 MPI network rules for SINUMERIK 810D
3.2
03/2006
MPI network rules for SINUMERIK 810D
Please take the following basic rules into account when undertaking network
installations:
3
1. The bus line must be terminated at both ends. To do this, activate the terminating resistor in the MPI connector of the first and last node, and deactivate
the remaining terminating resistors.
Note
S Only two resistors are permissible.
S With HHU, bus terminating resistors are hard-wired into the device.
2. It is necessary to apply 5 V voltage to at least 1 terminator. This occurs automatically when the MPI connector with active terminating resistor is connected to a live device.
3. Spur lines (lead cables from the bus segment to the node) should be as
short as possible.
Note
Any spur lines that are not assigned should be removed if possible.
4. Each MPI node must be connected before being activated. When disconnecting an MPI node, the connection must be deactivated before the connector can be pulled out.
5. You can either connect one HHU and one HT6, or two HHUs or HT6s per
bus segment. It is not permissible to connect bus terminators to the distributor boxes of an HHU or HT6.
If necessary, an intermediate repeater can be used to connect more than
one HHU/HT6 to a bus segment.
6. The following cable lengths for the standard MPI without repeater must not
be exceeded:
MPI (187.5 kBaud): max. total cable length 1000 m
Note
Piggy-back connectors are not recommended for power connections.
3-24
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
3.2
Example A
3 Settings, MPI/BTSS
MPI network rules for SINUMERIK 810D
ËËË
ËËË
ËËËËË
ËËË
ËËËËË
ËËËË
ËËËËËË
ËËË
ËËËËË
ËËËË
ËËËËËË
ËËËËË ËËËËËËË
ËËËËËËË
ËËËËËËË
ËËËËËËË
ËËËËËËË
on
HHU
Terminating resistor
fitted in connector
on
PCU
Distributor
box
on
MSTT
Terminating resistor
hard-wired in device
on
MPI
Control 810D
Fig. 3-4
Example B
Network installation with two terminating resistors in MPI:
BHG, control 810D
ËËËËËË
ËËËËËË
ËËËË
ËËËËËË
ËËËË
ËËËË
ËËËËËË
ËËËË
ËËËËËËËËËË
ËËËËËËËË
ËËËËËËË
ËËËËËËË
ËËËËËËË
ËËËËËËË
ËËËËËËË
on
Terminating resistor
fitted in connector
PCU
on
OP030
MSTT
Terminating resistor
hard-wired
on
MPI
on
Control 810D
Fig. 3-5
Network installation with two terminating resistors in MPI:
MSTT, control 810D
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
3-25
3
03/2006
3 Settings, MPI/BTSS
3.3 MPI default configuration for SINUMERIK 840D
3.3
MPI default configuration for SINUMERIK 840D
One or two machine control panels (interface for customer’s operating panels,
PP 031) and/or HHU are connected by means of parameter settings in the PLC
basic program (FB1). In this case, parameter settings using the STEP7 tool
“Communication Configuration” are no longer required.
3
Reference material: /FB1/
P3 Pl, Function manual for basic machines,
PLC basic program powerline
Standard
application
SINUMERIK 840D with one PCU and one machine control panel (MSTT) or
interface for customer’s operating panel on the BTSS.
Requirement for
the hardware
At least firmware release V 03_01_01 for
S MCP
S interface for customer’s operating panel/PP 031
Bus addresses
Every node on the MPI/BTSS bus must have a bus address (0...31).
ËËËËË
ËËËËË
ËËËËË
ËËËËË
PCU
Default bus addresses
1
BTSS 1.5 MBaud
ËËËËËËË
ËËËËËËËËËËËË
ËËËËËËË
ËËËËË
ËËËËË
ËËËËË
ËËËËË
ËËËËË
ËËËËË
ËËËËË
6
SINUMERIK 840D
X101
ËËËËË
ËËËËË
ËËËËË
ËËËËË
PG/start-up
tool
3
0
X122
MPI 187.5 kBaud
Fig. 3-6
3-26
13
NCK
MSTT/interface for
customer’s operating panel
PLC
2
Default application for SINUMERIK 840D
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
3.3
3 Settings, MPI/BTSS
MPI default configuration for SINUMERIK 840D
Bus address and
GD circuit
Note
The parameter settings for the bus address (on the machine control panel) or
the GD circuit parameters (on the HHU) in the PLC basic program are used for
the logical addressing of the components. The physical addressing on the
BTSS/MPI is always done via the GD circuits, however. Each machine control
panel, interface for customer’s operating panel, etc, must be addressed with a
separate GD circuit.
In the control, the bus address in the associated GD circuit is converted via the
PLC program.
On the machine control panel, the bus address, and thus the associated GD
circuits, are set via the DIP-FIX switches.
On the MPI, the same GD circuits are set, however, for the machine control panel, interface for customer’s operating panel and PP031 components, even if
the bus addresses are different. This should be noted if more than one machine
control panel, etc, is used.
The following table illustrates the interaction.
Table 3-4
Interaction between bus address and GD circuit
Bus addresses on the MPI
GD circuit
15, 14, 13
1
12, 11
2
10, 9
3
8, 7
4
6
8
5, 4
5
Example:
2 machine control panels (MSTTs) are to be connected to the MPI on a control.
The first MSTT can be connected to bus address 15 (GD circuit 1) and the second to bus address 12 (GD circuit 2).
MPI interface and
GD circuit
Note
If the “Communication Configuration” STEP7 tool is to be used to establish
PLC-PLC cross-communication on the MPI, for example, and if one or more
MSTTs are connected to the MPI, then the GD circuits assigned must be unique. The “Communication Configuration” STEP 7 tool assigns the GD circuits,
starting with GD circuit 1 in ascending order. If the MSTTs are connected to the
BTSS, then this has no effect on the PLC–PLC communication on the MPI.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
3-27
3
03/2006
3 Settings, MPI/BTSS
3.4 MPI default configuration for SINUMERIK 810D
Example:
GD circuits 1 and 2 are assigned by “Communication Configuration” as a result
of the PLC–PLC cross-communication. A first MSTT on the MPI can then be
assigned to GD circuit 3 (bus address 9 or 10), and a second MSTT on the MPI
to GD circuit 4 (bus address 7 or 8).
3
3.4
MPI default configuration for SINUMERIK 810D
Standard
application
SINUMERIK 810D with PCU and one machine control panel (MSTT) or interface for customer’s operating panel
Hardware
requirements
At least firmware release V 03_01_01 for
S MCP
S interface for customer’s operating panel
STEP7
from version 2.x
MPI baud rate
All MPI bus nodes operate at 187.5 kbaud.
Bus addresses
Every node on the MPI bus must have a bus address (0...15).
PCU
PG/start-up tool
1
0
Bus addresses
MPI bus
187.5 kbaud
14
SINUMERIK 810D
2
PLC
MSTT/interface for
customer’s operating panel
X122
3
NCK
Fig. 3-7
3-28
Standard application for SINUMERIK 810D
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
3.4
Communication
parameters
3 Settings, MPI/BTSS
MPI default configuration for SINUMERIK 810D
Configuration via FB1
If the MSTT/interface for customer’s operating panel is set to MPI address 14
and with SDB210 from the basic program diskette, the communication starts
when the PLC is restarted (LEDs stop flashing).
Note
The STEP7 project manager (S7 TOP) does not display the SDB as standard.
To display the SDB, select “All blocks with SDBs” in menu View/Set filters.
Assigned inputs/
outputs in the
PLC–CPU
The following bytes in the PLC CPU are then assigned to the MSTT or interface
for customer’s operating panel:
S Input byte 0–7
S Output byte 0–7
S Status bytes for error detection output bytes 12–15 (evaluated by basic
program)
Parameterization on FB1 (basic program) for the MCP is already preset for the
standard application.
Communication
does not start
If communication does not commence after a PLC reset (LEDs flashing), the
following points should be checked:
S The firmware release of the MSTT/interface for customer’s operating panel
must be at least V03_01_01.
Scan:
The firmware version is displayed on the left, central and right LED block of
the machine control panel if the keys “Feed start” and “Feed hold” are pressed simultaneously while the machine control panel is powering up.
S MPI cable and connector wiring
S DIP switch S3 (default setting)
SDB 210 must not be loaded.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
3-29
3
03/2006
3 Settings, MPI/BTSS
3.5 Deviation from standard configuration
3.5
Deviation from standard configuration
Required
documentation
The following additional publications are required:
Example
A configuration may be non-standard owing to one of the following:
3
Reference material:
/BH/ Device Manual, Operating Components
/FB/ P3, PLC basic program
/S7HT/ Manual, Application of Tools
S Change of address assignment
for the input, output or status bytes, or
for the flag area or data block
S Additional connection of a handheld unit (HHU)
S Connection of a 2nd MSTT or handheld terminal (HT 6)
In such cases, you must adjust the communications parameters and possibly
the switch settings (addresses) of the bus nodes.
Procedure
SIMATIC STEP7,
version 2.1
A new configuration is entered via the Define global data soft key. The following
description of how to proceed is based on the assumption that you already
know how to use this menu.
1. Set up new project and CPU programs using the STEP7 tool. A separate
CPU program should be set up for each component of the plant (PLC,
MSTT, HHU, 2.MSTT, HT 6, ...).
2. Connect the MPI nodes, i.e. network CPU programs with MPI address.
3. Activate the “Global Data” menu command in the following soft key
sequence File Manager/MPI Network/Extras/Global Data and enter the
desired configuration.
4. Compile this configuration. A new SDB is generated for each CPU program.
5. Set the cyclical transmission grid. Once the configuration has been compiled
successfully for the first time, the “Conversion factor” and “Status” can be
activated and then input.
6. Now compile your configuration again.
7. Transfer the SDB (from the CPU program of the PLC) to the PLC.
8. You must parameterize call FB1, DB7 in OB 100 in the basic PLC program
for all operator control components (MPI nodes).
9. You must configure the status pointer (double word) for every component in
FB1 for monitoring purposes.
Note
For a description of the “Global data” menu and the application, see
Reference material:
3-30
/S7HT/ SIMATIC Step7 Manual,
Starting up MPI bus nodes
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
3.6
3.6
3 Settings, MPI/BTSS
MPI interface for customer’s operating panel
MPI interface for customer’s operating panel
Interface
The interface is used to connect a customer’s operating panel. The module has
64 digital inputs and 64 digital outputs with C-MOS level (5V) for this purpose.
3
The module must have at least firmware release V 03_01_01.
Position of the
interfaces
289.4
64.7
X20
X211
X221
MPI connection
Equipotential bonding connection
X10
ON
Holes 3.6
S3 "
7.2
Fig. 3-8
Switch S3, default
setting for
SINUMERIK 840D
H3
H1
LEDs H4
H2
92.7
3.5
207.3
Front view of MPI interface for customer’s operating panel
If only the customer’s operating panel is connected, the bus address should be
set to 6 as for the MSTT (standard application).
Table 3-5
Switch S3, default
setting for
SINUMERIK 810D
X231
Setting for 840D: switch S3 interface for customer’s operating panel
1
2
3
4
5
6
7
8
on
off
on
off
on
on
off
on
Meaning:
Baud rate: 1.5 MBaud (BTSS)
Cyclical transmission interval:
100 ms
Bus address: 6
If only the customer’s operating panel is connected, the bus address should be
set to 14 as for the MSTT (standard application).
Table 3-6
Setting for 810D: switch S3 interface for customer’s operating panel
1
2
3
4
5
6
7
8
off
off
on
on
on
on
off
on
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Meaning:
Baud rate: 187.5 kBaud
Cyclical transmission interval:
100 ms
Bus address: 14
3-31
03/2006
3 Settings, MPI/BTSS
3.7 2nd machine control panel
Power supply
interface
Connector designation:
Connector type:
Table 3-7
X10
3-pin Phönix terminal block, straight
Assignment of connector X10 on interface for customer’s operating panel
X10
3
Pin
Name
Type
1
SHIELD
VI
2
M24
VI
3
P24
VI
Reference material:
3.7
/BH/ Device Manual, Operating Components
2nd machine control panel
SINUMERIK 840D/810D can be used to operate 2 machine control panels. The
2nd MSTT parameters must be set in the basic program parameters at FB1.
3-32
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
3.8
3.8
PCU 20/50/50.3/70
3.8.1
Settings with HMI Embedded/HMI Advanced for
SINUMERIK 840D
BTSS (standard)
3 Settings, MPI/BTSS
PCU 20/50/50.3/70
3
The operating panel interface (BTSS) is the default setting (1.5 MBaud).
S PCU 20 with HMI Embedded
HMI Embedded automatically adjusts to the baud rate.
S PCU 50/50.3/70 with HMI Advanced
The HMI Advanced must be set to a baud rate of 1.5 MBaud in the “Start-up/
HMI/Operating panel” menu.
Setting the display
machine data
The display machine data (BTSS settings) are set via the user interface of the
HMI in the Start-up area “Start-up” –> “Machine data”.
Language
S PCU 20 with HMI Embedded
The HMI Embedded software is available in six languages by default
(English, German, French, Italian, Spanish and simplified Chinese).
S PCU 50/50.3/70 with HMI Advanced
HMI Advanced is always supplied as a multilingual version. The default
setting is English.
Screen saver mode
MD 9006 (for HMI Embedded):
This MD is used to enter the time after which the screen saver mode is activated if no key is pressed on the operating panel within the specified time.
A detailed description of the functions and parameter settings can be found in
the following documentation:
Reference material: /IAM/ Start-up Guide, IM2, HMI Embedded
IM4, HMI Advanced
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
3-33
03/2006
3 Settings, MPI/BTSS
3.8 PCU 20/50/50.3/70
3.8.2
3
Settings with HMI Embedded/HMI Advanced for
SINUMERIK 810D
Setting the MPI
interface
For the SINUMERIK 810D, the MPI interface is set to 187.5 kBaud.
S PCU 20 with HMI Embedded
The PCU automatically adjusts to the baud rate.
S PCU 50/50.3/70 with HMI Advanced
The PCU must be set to a transmission speed of 187.5 kBaud in the
“Start-up/HMI/Operating panel” menu.
Setting the display
machine data
The display machine data (BTSS settings) are set via the user interface of the
HMI in the Start-up area “Start-up” –> “Machine data”.
Language
S PCU 20 with HMI Embedded
The HMI Embedded software is available in six languages by default
(English, German, French, Italian, Spanish and simplified Chinese).
S PCU 50/50.3/70 with HMI Advanced
The PCU with HMI Advanced is always supplied as a multilingual version.
The default setting is English.
Screen saver mode
MD 9006: This MD is used to enter the time after which the screen saver mode
is activated if no key is pressed on the operating panel within the specified time.
The settings for 3 different devices are made via the HMI in an input box in the
“Services” menu.
A detailed description of the functions and parameter settings can be found in
the following documentation:
Reference material: /IAM/ Start-up Guide, IM2, HMI Embedded
IM4, HMI Advanced
J
3-34
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
EMC and ESD Measures
4.1
4
RI suppression measures
4
Shielded signal
cables
To ensure safe, interference-free operation of the installation, it is essential to
use the cables specified in the individual diagrams. Both ends of the shield must
always have a conductive connection to the housing.
Exception:
S If non-Siemens devices are connected (printers, programming devices, etc.),
you can also use standard shielding cables which are connected at one
end.
These external devices may not be connected to the control during normal
operation. However, if the system cannot be operated without them, then the
cable shields must be connected at both ends. Furthermore, the external
device must be connected to the control via an equipotential bonding cable.
Construction rules
The following EMC measures must be followed to ensure maximum immunity to
interference in the overall plant (control, power section, machine).
S The signal and load cables must be kept as far apart as possible.
S Only original SIEMENS cables should be used as the signal cables from
and to the NCK and PLC.
S Signal cables must not be routed close to strong external magnetic fields
(e.g. motors and transformers).
S Pulse-carrying HC/HV cables must always be laid completely separately
from all other cables.
S If signal cables cannot be laid at a sufficient distance from other cables, then
they must be installed in shielded cable ducts (metal).
S The distance (interference liability surface) between the following cables
must be kept to a minimum:
!
–
Signal cable and signal cable
–
Signal cable and associated equipotential bonding conductor
–
Equipotential bonding conductor and PE conductor (routed together)
Important
For further notes on noise suppression and the connection of shielded cables,
see
Reference material: /EMV/ Configuration Guide, EMC installation guidelines
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
4-35
03/2006
4 EMC and ESD Measures
4.3 Heat dissipation
4.2
ESD measures
!
Important
Handling of modules containing devices sensitive to electrostatic discharge:
S When handling electrostatically sensitive devices, make sure that operator,
workplace and packing material are properly earthed.
S Generally, electronic modules must not be touched unless work has to be
4
carried out on them. When handling PC boards make absolutely sure that
you do not touch component pins or printed conductors.
S Touch components only if
–
you are permanently earthed by means of an antistatic chain,
–
you are wearing ESD boots or ESD boots with earthing strips in conjunction with ESD flooring.
S Modules may be placed only on electrically conductive surfaces (table with
ESD top, conductive ESD foam plastic, ESD packing bags, ESD transport
containers).
S Keep modules away from visual display units, monitors or TV sets (minimum distance from screen > 10 cm).
S Modules must not be brought into contact with chargeable and highly insulating materials, such as plastic films, insulating table beds or clothing made
from artificial fibres.
S Measurements on modules are allowed only if
4.3
–
the measuring instrument is properly earthed (e.g. equipment grounding
conductor), or
–
before measuring with a potential-free measuring instrument, the probe
is briefly discharged (e.g. touch the unpainted metal parts of the control
housing).
Heat dissipation
Please note:
!
Caution
A ventilation clearance of 100 mm must be left above and below the drive combination when it is installed.
J
4-36
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Power-On and Power-Up
5.1
5
Start-up order
Start-up sequence
5
The mechanical and electrical assembly work on the plant must be complete.
Before you commence starting up the control, you must ensure that it powers
up correctly with all its components and that it has been installed in compliance
with the EMC Guidelines.
The start-up procedure is detailed below. The order in which the individual steps
are taken is not mandatory, but recommended:
1. Power up and check the SINUMERIK 840D (chapter 5)
2. Basic settings (subsection 6.6.1) and
Entering the memory configuration (section 6.7)
3. Scaling machine data (section 6.8)
4. Setting the axis configuration (subsection 6.9.1)
5. Configuration and parameter settings for the drives (subsection 6.9.2)
6. Setting axis and spindle-specific machine data
–
Axis speeds (subsection 6.9.9)
–
Axis monitoring devices (subsection 6.9.11)
–
Axis reference point approaches (subsection 6.9.12)
–
Spindle data (subsection 6.9.13)
–
Sensor matching for spindle (subsection 6.9.15)
–
Spindle speeds (subsection 6.9.16)
–
Positioning the spindle (subsection 6.9.17)
–
Spindle monitoring devices (subsection 6.9.19)
7. Transferring PLC user program and alarm texts (chapter 7/8)
8. Axis and spindle test run (chapter 9)
9. Drive optimization (chapter 10)
–
Frequency response measurements for speed and position control loops
(section 10.5)
–
Analog output (section 10.8)
10. Data back-up (chapter 11)
11. Replacing hardware and software (chapter 12)
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
5-37
5 Power-On and Power-Up
5.2 NCU controls and displays
5.2
NCU controls and displays
Important controls
and displays for
power up
5
03/2006
Fig. 5-1 below shows the controls and displays on the NCU that are important
for powering on and powering up the SINUMERIK 840D:
S
S
S
S
S
S
S
Various error and status LEDs
7-segment status display (H3)
NMI button (S2)
RESET button (S1)
NC start-up switch (S3)
PLC start-up switch (S4)
PCMCIA slot
+5
NF
CF
VCB
CP
PR
P
P
–
PF0
S
F
Various error and status LEDs
Status display (H3)
Fig. 5-1
NMI button (S2)
RESET button (S1)
NC start-up switch (S3)
PLC start-up switch (S4)
X130A
MEMORY CARD
X172
X130B
S4 S3
Reset NMI
PCMCIA slot (X145)
SINUMERIK 840D controls and displays on the NCU
A detailed description of the controls and displays can be found in the following
documentation:
Reference material:
5-38
/PHD/ Device Manual, NCU Configuration
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
5.3
5.3
5 Power-On and Power-Up
CCU controls and displays
CCU controls and displays
Important controls
and displays for
power up
Fig. 5-2 below shows the controls and displays on the CCU that are important
for powering on and powering up the SINUMERIK 810D:
S
S
S
S
S
S
Various errorand status LEDs (H1/H2)
7-segment display (H3)
RESET button (S1)
NC start-up switch (S3)
PLC start-up switch (S4)
PCMCIA slot
5
.
.
Various error
and status LEDs
(H1/H2)
PCMCIA
slot
NCK start-up
switch (S3)
PLC start-up
switch (S4)
7-segment
display (H3)
Fig. 5-2
RESET
button (S1)
SINUMERIK 810D controls and displays on the CCU
A detailed description of the controls and displays can be found in the following
documentation:
Reference material: /PHC/ Device Manual, CCU Configuration
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
5-39
5 Power-On and Power-Up
5.4 Power-On and Power-Up
03/2006
5.4
Power-On and Power-Up
5.4.1
Power-On
Visual inspection
A visual inspection of the plant should be carried out in order to detect obvious
faults. Make sure that the mechanical installation of components is correct and
that electrical connections are firmly in place (e.g. in the DC link). Make sure
that all electrical connections have been made correctly before switching on the
power supply. Check the 230 VAC and 24 VDC supply voltages as well as the
shields and earthing connections.
Wiring blocks
The relevant wiring blocks on the MSTT, HHU, PLC I/O components should be
wired up and checked for start-up.
5
Reference material:
/BH/ Device Manual, Operating Components
Power-on
sequence
The MSTT, HHU and PCU components may be switched on in any order if they
are physically present.
Power-on
Switch on the power supply on all components and on the mains supply module. No enabling signals need be present initially on the mains supply module.
The LEDs on the NE module must not indicate any faults in the power supply.
!
5-40
Danger
Before switching on, make sure that the protective cover and connector X181
are attached to the power supply unit.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
5.4
5.4.2
5 Power-On and Power-Up
Power-On and Power-Up
Power-Up
After the power supply has been connected, the control system powers up. The
HMI Embedded/HMI Advanced system software is installed on the PCU when
the system is delivered, but it can also be installed via a PCMCIA card.
Note
The use of modules via L2-DP and certain CP modules means that the power
up time is longer than a standard configuration.
5
NCK general reset
To bring the control system into a defined initial state, initialization (NCK general
reset) is required when the power is first connected. To do this, turn the start-up
switch S3 on the NCU/CCU to position “1” and switch the control on. The control
then powers up, the SRAM memory is erased and the machine data are preset
to the default values.
Table 5-1
For the significance of the NCK start-up switch S3 (see Fig. 5-1)
Setting
Meaning
0
Normal mode: Power-up with the set data.
1
Start-up MODE: The data in the buffered RAM (SRAM) is cleared and the
default machine data is loaded.
2–7
Reserved
End of NCK
power-up
Once the NCK has powered up correctly, the number “6” appears on the NCU
status display. The LEDs “+5V” and “SF” (SINUMERIK READY) light up.
Now switch NC start-up switch S3 back to the “0” position.
Status display
during power-up
During power-up, the various power-up phases appear on the status display
(7-segment display) on the NCU module.
Table 5-2
Power-up phases on the status display (7-segment display)
Power-up
phase
Situation
.
An error was identified in the cyclical operation.
0
Real mode may have been switched to Protected mode.
1
Start of download from the PCMCIA card.
Number with
decimal point
The number of the module that has just been downloaded appears on
the status display.
2
Download from the PCMCIA card has ended successful.
3
The debug monitor is initialized.
4
Operating system was downloaded successfully.
5
Operating system has started up.
6
NCK software is initialized.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
5-41
5 Power-On and Power-Up
5.4 Power-On and Power-Up
03/2006
Note
No display means:
The CPU self-test did not work. Defective module.
A flashing display means:
A FATAL ERROR occurred when the system was powered up. The cause of
the error can be identified from the combination of flashes.
PLC general reset
5
Use GENERAL RESET to clear the PLC’s program memory.
The diagnostics buffer of the PLC is not erased.
Once the NCK has powered up, a general reset should be carried out to return
the PLC to its basic state. There are two ways of doing this:
1. By means of the programming device with SIMATIC Step7
2. Using the PLC start-up switch S4 on the NCU/CCU module
Table 5-3
Settings with the PLC start-up switch S4 (see Fig. 5-1)
Meaning
Setting
0
PLC-RUN-PROGRAMMING: RUN operating state.
It is possible to intervene in the PLC program.
1
PLC-RUN: RUN operating state.
The program can only be accessed for reading via the programming devices.
2
PLC-STOP: STOP operating state.
3
MRES: This setting is used for a module reset (general reset function).
Note
When starting up for the first time, or replacing a module, or when a battery
fails, or the PLC requests a MRES, or the PLC operating system is upgraded,
the complete memory reset is absolutely necessary:
1. Set PLC start-up switch S4 to position “3”.
2. Turn NCK start-up switch S3 to position 1 (which will clear the DRAM
between the NCK and PLC).
3. Perform POWER ON and hardware RESET.
4. PLC general reset:
Actions for PLC
restart
The following step will RESTART the PLC:
S Turn PLC start-up switch S4 from position “2” (STOP mode) to position “1”
or “0” (RUN mode).
S Perform POWER ON and hardware RESET.
5-42
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
5.4
Actions for PLC
general reset
5 Power-On and Power-Up
Power-On and Power-Up
The following steps with the PLC start-up switch S4 will cause a
PLC GENERAL RESET:
1. Turn to position “2” (STOP operating state)
⇒ PS LED lights up.
2. Turn to position “3” (MRES operating state, request general reset) and hold
in this position (for approx. 3 second) until the PS STOP LED lights up
again.
⇒ PS LED goes out and comes on again.
3. Within 3 second, turn to the
STOP-MRES-STOP (“2”–“3”–“2”) positions
⇒ PS LED PS first flashes at approx. 2 Hz and then lights up again
⇒ PF LED lights up
5
4. Once the PS and PF LEDs are lit, turn the switch S4 to position “0”
⇒ The PS and PF LEDs goes out and the PR LED (green) lights up
⇒ A general reset of the PLC is complete. It is now in cyclical mode.
Note
If a hardware RESET or POWER ON is initiated in switch position 3 on PLC
start-up switch 4 the entire SRAM contents of the PLC are initialized, the
diagnostic buffer contents are not deleted. All user data have to be transferred
again.
If setting “3” (MRES) is selected for less than 3 seconds, then no general reset
is requested. The STOP LED does not light up if the switch is not changed from
setting STOP to MRES to STOP within 3 seconds after a general reset has
been requested.
Reference material:
/S7H/ SIMATIC Step7-300
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
5-43
5 Power-On and Power-Up
5.4 Power-On and Power-Up
5.4.3
03/2006
PCU power-up
PCU power-up
After the power supply has been switched on, the PCU powers up automatically. The system software is installed in the factory and is ready to run. The
basic display appears on the screen if the MMC has powered up successfully.
Problems during
power-up
PCU 20
If the PCU is unable to establish a connection to the NCK, the message “wait
for NCU-connection:“x” seconds”, “x” = 1 to 60 appears. If no connection is
established after this time, the PCU is quickly rebooted.
Check the following:
5
S Is the NCU module on standby?
(number 6 on H3)
S Is the MPI cable inserted, is cable attached properly to connector?
S Are other MPI stations (machine control panel, handheld unit, ...) disturbing
MPI communication? (Remove connections to test.)
S If the reset button on the NCU was pressed again during power-up (e.g. as
for software upgrade [Position 1/PLC Reset]), the control must be switched
off and on again for the PCU power-up to be successful.
PCU 50/50.3/70
If the PCU does not power up and the screen remains dark, then check the
24 V DC power supply. If the power supply at the PCU’s power supply unit is
correct and the 7-segment display on the back remains dark, then the PCU is
faulty.
If the PCU powers up, but is unable to establish a connection to the NCK, then
the message “Communication with NCK failed” appears in the bottom message
line.
In this case, please check the following:
S Is the NCU module on standby (number 6 on H3)?
S Is the MPI cable inserted, is cable attached properly to connector?
S Is the baud rate in menu Start-up/HMI/operator panel front set correctly? It
must be set to 187.5 (password for protection level 2 required).
S Are other MPI stations (machine control panel, handheld unit, ...) disturbing
MPI communication? (Remove connections to test.)
5-44
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
5 Power-On and Power-Up
Power-On and Power-Up
03/2006
5.4
5.4.4
Error while Control power-up
Display on the
status display
During power-up, various status messages appear on the display (7-segment
display) on the NCU/CCU. The digit “6” is output when the control has finished
powering up.
Problems while
powering up NC
If the display does not read “6” after approx. 2 minutes, and:
S another number appears,
S the display remains dark,
5
S the display flashes,
then proceed as follows:
1. Repeat the NCK general reset.
2. The switch S3 (NCU) must be reset to “0”.
3. If the NCK general reset is unsuccessful, replace the PCMCIA card and
reinstall the software.
4. If these actions are unsuccessful, replace the NCU module.
Status displays on
the PLC
The front panel of the NCU module (see Fig. 5-1) contains the following LEDs to
indicate the operating states of the PLC:
PR
PLC-RUN (green)
PS
PLC-STOP (red)
PF
PLC-Watchdog (red)
PFO
PLC-FORCE (yellow)
–
Profibus (yellow)
PR and PSLEDs
Table 5-4
Status displays of the PR and PSLEDs
LED PR
lights
up
off
flashes
0.5 Hz
flashes
at 2 Hz
off
off
LED PS
off
lights
up
lights
up
lights
up
– lights up
– for 3 sec.
off
– lights up
– lights up
– flashes at
2 Hz (at least
3 sec.)
– lights up
Meaning
RUN
STOP
HALT
RESTART
GENERAL RESET requested
GENERAL RESET in progress
RUN:
The PLC program is being processed.
STOP:
The PLC program is not being processed. STOP can be set by the PLC program, error identifiers or an operator input.
HALT:
“Halt” of the PLC user program (initiated by test function).
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
5-45
5 Power-On and Power-Up
5.4 Power-On and Power-Up
03/2006
RESTART:
The control is started (transition from STOP to RUN state). If the start process is
aborted, the control switches back to the STOP state.
PF LED
This LED lights up when the PLC watchdog has responded.
PFO LED
A defined value is assigned to a variable by means of the FORCE function. The
variable is write-protected and cannot be changed from any location. The write
protection remains effective until it is canceled by the UNFORCE function. If the
PFO LED is out, then no FORCE job is present.
Profibus
The Profibus LED corresponds to the BUSF LED on the SIMATIC CPU 315-DP.
See the CPU data installation guide for a description.
5
Note
If all 4 LEDs on the status display flash after the NCU hardware is replaced,
then you must power up the NCK again. A PLC general reset can then be carried out if necessary.
5.4.5
Power-up of machine control panel (MSTT)
Software release
Press the “Start feed” and “Stop feed” buttons while the machine control panel
is powering up (all the LEDs flash) to display the version number of the software
on the machine control panel. This means that the system software on the machine control panel has started up correctly and is waiting for the PLC to start
cyclical communication.
A detailed description of the machine control panel used can be found in the
following documentation:
Reference material: /BH/ Device Manual, Operating Components
5.4.6
Power-up
Powering up the drives
After a NCK general reset, the drives are disabled and there are no data records for the drives (known as boot files). The “SF” LEDs on the NCU module
and on the 611D controller light up.
Detailed information on powering up SIMODRIVE 611 universal drives can be
found in the following document:
Reference material:
/FBU/ SIMODRIVE 611 universal function guide
5-46
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
5.4
5.4.7
5 Power-On and Power-Up
Power-On and Power-Up
PCU/HMI Advanced BIOS setup
The default settings in the BIOS of the PCU/HMI Advanced can be displayed
directly on screen during power-up.
S Start the control
S At the prompt, press the BIOS setup key <F2> or horizontal soft key 2 on
the OP. The BIOS setup menu appears.
Note
The settings for the BIOS default parameters are described in the following
documentation:
Reference material:
5
/IAM/ IM4, HMI Advanced Start-up Guide
/BH/ Device Manual, Operating Components
J
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
5-47
5 Power-On and Power-Up
5.4 Power-On and Power-Up
03/2006
Notes
5
5-48
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6
Programming the control
6.1
Machine and setting data
Programming
The control is matched to the machine by means of machine and setting data.
Machine data
The machine data (MD) is classified as follows:
S General machine data
S Channel-specific machine data
S Axis-specific machine data
S Display machine data (machine data for front control panel)
S Machine data for feed drive
S Machine data for main spindle drive
Setting data
The setting data (SD) is classified as follows:
S General setting data
S Channel-specific data
S Axis-specific setting data
Option data
Used to enable options. Option data is supplied with the specific option.
Overview of
machine and
setting data
The machine and setting data is divided into the following areas:
Table 6-1
Overview of machine and setting data
Area
Designation
from 1000 to 1799
Machine data for SIMODRIVE drives
from 5000 to 6000
Machine data for the hydraulic module
from 9000 to 9999
Display machine data
from 10000 to 18999
General machine data
from 19000 to 19999
Reserved
from 20000 to 28999
Channel-specific machine data
from 29000 to 29999
Reserved
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-49
6
03/2006
6 Programming the control
6.1 Machine and setting data
Table 6-1
Overview of machine and setting data, continued
Area
6
Designation
from 30000 to 38999
Axis-specific machine data
from 39000 to 39999
Reserved
from 41000 to 41999
General setting data
from 42000 to 42999
Channel-specific data
from 43000 to 43999
Axis-specific setting data
from 51000 to 61999
General machine data for compile cycles
from 62000 to 62999
Channel-specific machine data for compile cycles
from 63000 to 63999
Axis-specific machine data for compile cycles
Entering machine
data
Menus are provided for entering the machine data. How to select displays:
Press the “MENÜ SELECT” button: The menu bar with the following areas appears on screen: Machine, Parameters, Program, Services, Diagnostics and
Start-Up.
Press the “Start-up” soft key and the “Machine data” soft key.
Bit editor for HEX
machine data
A bit editor is implemented for setting certain machine data bits. If the input cursor in the MD list is on a machine data item in HEX format, the editor can be
called up by pressing the Toggle key.
Note
The bit editor for HEX machine data is only available in conjunction with the
HMI.
Fig. 6-1
6-50
Input screen in the bit editor for HEX machine data
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
6.1
6 Programming the control
Machine and setting data
The individual bits can be set or reset by clicking on them with the mouse.
Alternatively they can be selected using the cursor keys and then pressing the
Toggle key.
S Press the “OK” soft key to exit the bit editor and accept the set value.
S Press the “Cancel” soft key to exit the bit editor and reject the set value.
The previous setting is restored.
6
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-51
03/2006
6 Programming the control
6.2 Handling machine and setting data
6.2
Handling machine and setting data
Number and
identifier
MD and SD are addressed by number or by name (identifier). The number and
name are displayed on the HMI user interface. The following must also be
noted:
S Active
S Protection level
S Unit
S Default value
S Value
6
Active
The levels at which a data item takes effect are listed below in order of priority.
A change to the data takes effect after:
S POWER ON (po)
NCK-RESET
S NEW_CONF (cf)
– “Activate MD” soft key on the HMI
– “RESET” button on the MSTT
– Changes in program mode at the start and end of
records possible
S RESET (re)
– at the end of program M2/M30, or
– “RESET” button on the MSTT
S IMMEDIATELY (so) after entering the value
Protection levels
Protection levels are identified by numbers and are used to enable data areas.
A more detailed explanation can be found in the next section: Protection level
concept.
Unit
The unit refers to the default setting for the machine data:
S MD_$MN_10220_SCALING_USER_DEF_MASK (activates the scaling
factors)
S MD_$MN_10230_SCALING_FACTORS_USER_DEF (scaling factors for
the physical variables)
S MD_$MN_10240_SCALING_SYSTEM IS METRIC=1 (basic system is
metric)
If the MD is not based on any physical unit, then the field contains a “–”.
Default value
This value is used to set the machine or setting data to its default.
Note
On the HMI, input is limited to 10 digits plus decimal point and sign.
6-52
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
6.3
Range of values
6 Programming the control
Protection level concept
Indicates the input limits. If no range of values is specified, the data type determines the input limits and the field is identified with “∗∗∗”.
A detailed explanation of the machine data and a list of all the machine and setting data can be found in the following documentation:
Reference material:
6.3
/LIS1/ Lists
Protection level concept
Protection levels
In SINUMERIK 840D there is a protection level concept to enable data areas.
Protection levels range from 0 to 7, 0 representing the highest and 7 the lowest
level.
The lock for protection levels
S 0 to 3 is set with a
password in the “Start-up”
operating area.
S 4 to 7 is set directly with key switch positions 3 to 0
on the machine control panel (MSTT).
Protection level 4 (key switch position 3) and higher is required to display
machine data.
The appropriate protection level must generally be enabled by means of password “EVENING” to start up the system.
Table 6-2
Protection level concept with the relevant data areas
Protection level
Protection levels
0–3
Locked by
data areas
0
Password
1
Password: SUNRISE (default)
Machine manufacturer
Siemens
2
Password: EVENING (default)
Commissioning engineer,
Service
3
Password: CUSTOMER (default)
4
Key switch position 3
Programmer, machine setter
5
Key switch position 2
Qualified operator
6
Key switch position 1
Trained operator
7
Key switch position 0
Semi-skilled operator
End user
Protection levels 0 to 3 require a password to be entered. The password for
level 0 provides access to all data areas. For protection levels 1 to 3, default
passwords are defined when the system is powered up in start-up mode (NCK
start-up switch in position 1). To guarantee secure access, these default passwords MUST be changed once they have been activated. If, for example, the
passwords have been forgotten, then the system must be reinitialized (NCK
general reset). This resets all passwords to the standard of this software
version.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-53
6
03/2006
6 Programming the control
6.3 Protection level concept
In the Start-up area “Start-up”, you can change the set password using a soft
key. The password remains valid until it is reset with the soft key DELETE
PASSWORD. A POWER ON does not reset the password.
Reference material:
Protection level
4–7 key switch
/BAD/ HMI Advanced User Guide
BEM/ HMI Embedded User Guide
Protection levels 4 to 7 each require a different key switch position on the machine control panel. Three keys of different colors are provided for this purpose.
Each of these keys is capable of providing access to particular data areas.
Table 6-3
6
Meaning of key switch positions
Key color
Switch position
Protection level
(no key inserted)
0 = Remove key position
7
Black
0 and 1
6–7
Green
0 to 2
5–7
Red
0 to 3
4–7
Note
The associated interface signals can be found in DB10, DBX56.4–7, see
Reference material:
/FB1/ A2, Basic machine function guide,
Various NC/PLC interface signals,
Section: Key switch position
Redefining protection levels
The user can modify the protection levels for reading and writing data. This prevents display and input of certain data. Only protection levels of lower priority
can be assigned to the machine data, setting data can also be assigned protection levels of higher priority. The commands APR and APW are used to change
the protection levels.
The protection levels of individual machine or setting data can be changed in
the SGUD.DEF file.
Example SGUD.DEF file:
%_N_SGUD_DEF
;$PATH=/_N_DEF_DIR
REDEF $MA_CTRLOUT_SEGMENT_NR APR 2 APW 2 (APR ... read rights)
REDEF $MA_ENC_SEGMENT_NR APR 3 APW 2
(APW ... write rights)
REDEF $SN_JOG_CONT_MODE_LEVELTRIGGRD APR 7 APW 2
M30
The file becomes active when the next _N_INITIAL_INI is read in. Different protection levels are specified for writing (changing) or reading (part program or
PLC).
Example:
MD 10000 is protected by levels 2/7, i.e. writing requires protection level 2
(corresponding to password) and reading requires protection level 7. To be able
to enter the machine data area you need at least key switch position 3.
Reference material:
6-54
/PGA/ Programming Guide: Preparing for work
/FB1/ A2, “Various interface signals”
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
6.3
6.3.1
6 Programming the control
Protection level concept
Protection levels for NC language commands (REDEF)
Access rights to
execute NC
commands
The existing protection level concept for accessing machine and setting data
and GUDs has been extended to include executing certain part program commands and write access to system variables. Individual part program commands are thus associated with a corresponding right of use.
The default setting for the current right of use corresponds to the access right
that is active on the control, i.e. to key switch position 0 to 3 or passwords for
end users through to Siemens, as shown in Table 6-2.
To allow the programs stored in the cycle directories to be used via a range of
commands that are independent of the rights of use of a particular operator, the
right of use is implicitly modified while these programs are running. To do this,
when programs are called from the cycle directories, the right of use is set to the
values stored in machine data MD 11160 to MD 11162, provided that a higher
access right has not already been set on the control by key switch or password.
Table 6-4
Modifying rights of use for the cycle directories
Assign defined rights of use
Allocation of protection levels with
REDEF command
to the cycle directory
MD 11160: ACCESS_EXEC_CST
/_N_CST_DIR (standard cycles)
MD 11161: ACCESS_EXEC_CMA
/_N_CMA_DIR (manufacturer’s cycles)
MD 11162: ACCESS_EXEC_CUS
/_N_CUS_DIR (user cycles)
NC language commands are assigned protection levels using the REDEF command. The following language constructs may be protected:
S G codes (list of G functions/preparatory functions)
S Predefined procedures and functions (predefined subprograms)
S “DO” instructions for synchronous actions only
S Write or read access to machine and setting data
S Write access to system variables (part program and synchronous actions)
S Cycle identifiers (PROC instruction)
S Language commands that were generated via the compile cycle interfaces.
Once the part program commands have been activated, they are not executed
unless the relevant right of use exists. If this is not the case, then processing of
the part program is canceled and alarm 14018 is output.
Activating the
protection levels
As with the GUD definitions, separate definition files are provided for programming the REDEF instruction:
Siemens system applications
Machine manufacturer
End user
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
/_N_DEF_DIR/_N_SACCESS_DEF,
/_N_DEF_DIR/_N_MACCESS_DEF and
/_N_DEF_DIR/_N_UACCESS_DEF
6-55
6
03/2006
6 Programming the control
6.3 Protection level concept
When the control is powered up, these are evaluated in order, from
/_N_DEF_DIR/_N_SACCESS_DEF to /_N_DEF_DIR/_N_UACCESS_DEF.
Protection levels can only be allocated in these definition files. Apart from these
files, processing of the REDEF command is rejected and alarm 14018 is output.
Defining write
protection for
definition files
To be able to check whether the REDEF instructions programmed in the definition files are correct, the write protection for each definition file is evaluated. It
must be equal to or greater than the
protection level specified in the REDEF command and the protection level currently assigned to the part program command or the machine or setting data.
Alarms 7500 and 15180 are triggered if these conditions are not fulfilled.
The write protection for the definition files is set via MD 11170 to MD 11172. Values between –1 and 7 are possible. If the value is –1, the value currently set in
the relevant definition file is retained.
6
Table 6-5
Setting write protection for the definition files
Machine data
Associated definition directories
MD 11170: ACCESS_WRITE_SACCESS
/_N_DEF_DIR/_N_SACCESS_DEF
MD 11171: ACCESS_WRITE_MACCESS
/_N_DEF_DIR/_N_MACCESS_DEF
MD 11172: ACCESS_WRITE_UACCESS
/_N_DEF_DIR/_N_UACCESS_DEF
Subprograms may be called in the above definition files. They must have the
extension _SPF or _MPF and be located in the search path for subprogram
calls or be called with the absolute path. They inherit the write protection of the
definition files set with MD 11170-11172: ACCESS_WRITE_xACCESS. For the
REDEF command,
see Reference material: /PGA/
Defining write
protection for
cycle directories
To ensure that the implicit right to use the cycle directories is not misused, write
protection for these directories can be matched to the specific right of use with
MD 11165-11167.
Table 6-6
Setting the write protection for cycle directories
Machine data
6-56
Programming Guide for Work Preparation,
Section: 3
Associated cycle directories
MD 11165: ACCESS_WRITE_CST
/_N_CST_DIR (standard cycles)
MD 11166: ACCESS_WRITE_CMA
/_N_CMA_DIR (manufacturer’s cycles)
MD 11167: ACCESS_WRITE_CUS
/_N_CUS_DIR (user cycles)
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
6.3
6 Programming the control
Protection level concept
Note
The data back-up ensures that the protection levels set for the definition files
and cycle directories are also backed up and can be restored during standard
system start-up. See section 11 “Data back-up” and
Reference material: /BAD/ User Guide,
Section: Services area, Start-up functions
/BEM/ User Guide,
Section: Services area , Standard system start-up
6.3.2
Configurable parameter areas for GUD blocks
Configuring
parameter areas
Individual GUD blocks can be supplemented with the following machine data to
provide additional, channel-specific parameter areas:
MD 18660: MM_NUM_SYNACT_GUD_REAL[index] = <value>
MD 18661: MM_NUM_SYNACT_GUD_INT[index]
= <value>
MD 18662: MM_NUM_SYNACT_GUD_BOOL[index] = <value>
Fields are created with the following properties:
S Synact GUD of data type REAL, INT or BOOL with predefined names
SYG_....
S The field size corresponds to the <value> of the relevant machine data
S The new parameters may be read and written to both by the part program
and via synchronous actions. Once the relevant machine data has been set,
they are available the next time the control is powered up, and thus behave
like R parameters.
Table 6-7
Configuring additional parameter areas
$MN_MM_NUM_SYNACT_GUD
MD 18660
MD 18661
MD 18662
Supplements
GUD block
REAL[0]=<value> INT[0]=<value>
BOOL[0]=<value>
SGUD block
REAL[1]=<value> INT[1]=<value>
BOOL[1]=<value>
MGUD block
REAL[2]=<value> INT[2]=<value>
BOOL[2]=<value>
UGUD block
REAL[3]=<value> INT[3]=<value>
BOOL[3]=<value>
GUD4 block
REAL[4]=<value> INT[4]=<value>
BOOL[4]=<value>
GUD5 block
REAL[5]=<value> INT[5]=<value>
BOOL[5]=<value>
GUD6 block
REAL[6]=<value> INT[6]=<value>
BOOL[6]=<value>
GUD7 block
REAL[7]=<value> INT[7]=<value>
BOOL[7]=<value>
GUD8 block
REAL[8]=<value> INT[8]=<value>
BOOL[8]=<value>
GUD9 block
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-57
6
03/2006
6 Programming the control
6.3 Protection level concept
Table 6-8
Predefined names for the additional parameters
Predefined names for Synact_GUD of type Real, Int
and Bool
Synact-GUD in
SYG_RS[ ] Real
SYG_IS[ ]
Int
SYG_BS[ ] Bool
SGUD block
SYG_RM[ ] Real
SYG_IM[ ]
Int
SYG_BM[ ] Bool
MGUD block
SYG_RU[ ] Real
SYG_IU[ ]
Int
SYG_BU[ ] Bool
UGUD block
SYG_R4[ ]
Real
SYG_I4[ ]
Int
SYG_B4[ ]
Bool
GUD4 block
SYG_R5[ ]
Real
SYG_I5[ ]
Int
SYG_B5[ ]
Bool
GUD5 block
SYG_R6[ ]
Real
SYG_I6[ ]
Int
SYG_B6[ ]
Bool
GUD6 block
SYG_R7[ ]
Real
SYG_I7[ ]
Int
SYG_B7[ ]
Bool
GUD7 block
SYG_R8[ ]
Real
SYG_I8[ ]
Int
SYG_B8[ ]
Bool
GUD8 block
SYG_R9[ ]
Real
SYG_I9[ ]
Int
SYG_B9[ ]
Bool
GUD9 block
6
Access, display
and operation
The new parameters are
S displayed in the “Parameter area” on the HMI. Even if no GUD definition files
are effective, the new parameters are still available in the relevant GUD
block.
S Deletion is handled as follows:
If the content of a certain GUD definition file is reactivated, then the old GUD
data block in the active file system is first deleted. The new parameters are
also reset.
If this operation takes place via the HMI in the “Services area” under Manage data using the Define and Activate user data (GUD), then the contents
of the variable are saved to INI files and are restored at the end of the operation.
Keywords
The protection level assignments that are possible using the APR and APW
keywords in a GUD definition file continue to relate only to the GUDs defined in
this GUD definition file.
Protection levels for Synact GUDs are assigned via the REDEF command.
Values assigned
with checksums
The protection levels assignments take effect when the power up is complete.
If, during a standard system start-up, for example, it should be possible to run
initialization files with value assignments on protected variables without having
to modify the access right, then the value assignments must be protected by
checksums.
This method is already used when initializing machine data, setting data and
GUDs. Setting Bit0 in MD 11230: MD_FILE_STYLE means that, when initialization files are generated, a checksum is generated for each value assignment in
these files.
Note
From software version 7.1 onwards, this checksum is generated for all data to
be protected via initialization files.
Exception: R parameters.
6-58
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
6.3
6 Programming the control
Protection level concept
Example of a value assignment with checksum:
N18120 $MN_MM_NUM_GUD_NAMES_NCK=20 ’620c
(Checksum 620c preceded by an apostrophe)
When the initialization file is downloaded, there is a check to ensure that the
checksum is valid. If this is the case, the associated value assignment is executed, even if the access right set on the control is not sufficient.
Complete start-up
The complete start-up procedure for the function is as follows:
1. Create the definition files
/_N_DEF_DIR/_N_SACCESS_DEF
/_N_DEF_DIR/_N_MACCESS_DEF
/_N_DEF_DIR/_N_UACCESS_DEF
Siemens system applications
Machine manufacturer or
End user
2. Set the write protection for the definition files to the value required for
redefinition as follows using the machine data:
MD 11170: ACCESS_WRITE_SACCESS
Siemens system applications
MD 11171: ACCESS_WRITE_MACCESS
Machine manufacturer and
MD 11172: ACCESS_WRITE_UACCESS
End user
3. Modify the rights to use the cycle directories as follows if the protected
commands are to be permitted there.
_N_CST_DIR, _N_CMA_DIR and _N_CUS_DIR
via machine data:
MD 11160: ACCESS_EXEC_CST Standard cycles
MD 11161: ACCESS_EXEC_CMA Manufacturer’s cycles and
MD 11162: ACCESS_EXEC_CUS User cycles
4. Modify the write protection for the cycle directories to the right to use set
above as follows so that the implicit right to use the cycle directories cannot
be misused.
_N_CST_DIR, _N_CMA_DIR and _N_CUS_DIR
via machine data:
MD 11165: ACCESS_WRITE_CST Standard cycles
MD 11166: ACCESS_WRITE_CMA Manufacturer’s cycles and
MD 11167: ACCESS_WRITE_CUS User cycles
Examples
Machine data
Right to use cycle directories:
MD 11160: ACCESS_EXEC_CST = 2
MD 11161: ACCESS_EXEC_CMA = 2
MD 11162: ACCESS_EXEC_CUS = 3
;
; Machine manufacturer
; Machine manufacturer
; End user
Write protection for cycle directories:
MD 11165: ACCESS_WRITE_CST = 2
MD 11166: ACCESS_WRITE_CMA = 2
MD 11167: ACCESS_WRITE_CUS = 3
;
; Machine manufacturer
; Machine manufacturer
; End user
Write protection for definition files:
MD 11171: ACCESS_WRITE_MACCESS = 1
MD 11172: ACCESS_WRITE_UACCESS = 3
; set to value
; Machine manufacturer
; End user
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-59
6
03/2006
6 Programming the control
6.3 Protection level concept
Definition file for the machine manufacturer
%_N_MACCESS_DEF
;$PATH=/_N_DEF_DIR
File for machine manufacturer
; Write protection for file is set to value 1 for machine manufacturer.
N010
; Predefined procedures:
N020 REDEF CONTPRON APX 1 ; Record preparation for cutting cycle,
; Protection level: Machine manufacturer
N030 REDEF GEOAX APX 3
; Geo axis assignment,
; Protection level: End user
N110
N120 REDEF INTERSEC APX 1
; Predefined functions:
; Point of intersection calculation
; Protection level: Machine manufacturer
; Write access to
N110
; System variables:
N120 REDEF $P_CHBFR APW 3 ; Write basic frame
N130 REDEF $TC_MAP1 APW 3 ; Magazine data for tool management
; Write protection level: End user
6
N210
N220 REDEF DO APX 2
; Synchronous actions
; Protection level: Start-up engineer, Service
; Machine data
; $MC_GCODE_RESET_VALUES for
N310
; Protection level: Enable key switch 0
N320 REDEF $MC_GCODE_RESET_VALUES APR 7 APW 7
M17
Definition file for the end user
%_N_UACCESS_DEF
;$PATH=/_N_DEF_DIR
File for end user
; Write protection for file is set to value 3 for end user.
; Protection level for writing
; $MC_GCODE_RESET_VALUES for
; set end user
N510 REDEF $MC_GCODE_RESET_VALUES APR 7 APW 3
M17
6-60
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
6.4
6.4
Display filter for machine data
6.4.1
Function
6 Programming the control
Display filter for machine data
Using the display filter allows the number of machine data items displayed to be
reduced to a specific number, and thus adapted to suit the user’s needs.
All machine data in the following areas:
S General machine data
S Channel-specific machine data
S Axis-specific machine data
S Drive machine data (FDD/MSD)
6
are assigned to specific groups.
You can tell which group specific machine data belongs to by referring to the
machine data list.
Reference material:
/LIS1/ Lists
S Each area has its own group assignment.
S Each machine data in the different areas can be assigned to several groups.
6.4.2
Selecting and setting the display filter
Selecting the list
screens
The filter is selected and activated via a list screen which is opened using the
“Display options” vertical soft key in the relevant machine data areas.
The display will vary according to which HMI software you are using. See:
Reference material:
Display criteria
/BAD/ HMI Advanced User Guide
/BEM/ HMI Embedded User Guide
If the user’s access rights (password) are not sufficient, then the machine data
is not displayed. If the access rights are sufficient, there is a check to see if any
display filters are active.
Note
You can tell which group specific machine data belongs to by referring to the
machine data list.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-61
03/2006
6 Programming the control
6.4 Display filter for machine data
Table 6-9
Display criteria
S
S
Display filter active
S
Expert mode
S
S
Group filters
S
S
All others
6
S
S
S
Index from to
Activating group
filters via
checkboxes
Inactive: All the machine data is displayed.
Active: Test for group filter
Inactive: the MD is assigned to Expert mode
=> MDis not displayed
Active: the MD is assigned to Expert mode
=> MD is displayed (note index)
Inactive: MD is assigned to the group
=> MDis not displayed
Active: MD is assigned to the group
=> MD is displayed (note index)
Inactive: for MDs that are not assigned to any group
=> MDis not displayed
Active: for MDs that are not assigned to any group
=> MD is displayed (note index)
Inactive: all subparameters of the MD are displayed
Active: only the specified subparameters of the MD
are displayed
The checkboxes are selected using the cursor keys and are checked/
unchecked with the toggle key.
S If a filter is disabled (not checked), then the corresponding machine data is
not displayed.
S If a filter is enabled (checked), the corresponding machine data is displayed.
However, it is necessary to pay attention to the “Index from to” filter.
Note
If the “Index from to” filter is active, note the following point:
If only the “first” index (0) is to be displayed, then the other settings for the override switch (MD 12000.1: OVR FACTOR_AX_SPEED), for example, will also be
hidden.
Vertical soft keys
S “Select all” soft key
The checkboxes for the groups are set to active.
The soft key does not affect the following checkboxes:
– Filter active
– Expert mode
– Index from to
– All others
6-62
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
6.4
6 Programming the control
Display filter for machine data
S “Deselect all” soft key
The checkboxes for the groups are set to inactive.
The soft key does not affect the following checkboxes:
– Filter active
– Expert mode
– Index from to
– All others
S “Cancel” soft key
– Returns to the machine data screen.
– The former filter settings remain valid
– Any changes are discarded
S “OK” soft key
– Modified filter settings are saved.
– The machine data screen is refreshed
– The input field is positioned on the current MD again.
If the MD was hidden, then it is positioned on the first MD.
Expert mode
6
The “Expert mode” setting is intended to simplify and give a clearer overview of
the initial start-up process.
Procedure:
S Activate all filters (check)
S Activate display filters (check)
S Disable expert mode (do not check)
S Only the machine data required for the basic functions are displayed
(e.g. proportional gain, reset time, filters).
Machine data for adaptation, the reference model, etc, is not displayed.
Hide all machine
data
If the filter setting hides all the machine data in an area, when this area is selected, the following message appears:
“Unable to display machine data with the current access rights and the current
filter setting”.
Press the “OK” soft key to acknowledge and blank machine data screen
appears.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-63
03/2006
6 Programming the control
6.5 Example of a start-up concept
6.5
Example of a start-up concept
Objective
1. Simple standard system start-up for the initial start-up
2. Inclusion of machine options (e.g. rotary tables or 2nd spindle)
3. Shorter start-up time
4. Simplified machine data handling by means of user screens for mechanics
or measuring engineers.
5. Standardized PLC program for the entire series of machines
6
Basic machine
The following upgrade variants are available, e.g. for a milling machine with one
or two rotary tables or spindles.
Starting from a basic variant
S with three axes (X11,Y11,Z11),
S magazine axis (B11),
S spindle (C11)
a standard system start-up file is created.
When the machine data is declared for this basic machine, all the possible
optional axes are declared in the machine axis data.
This affects one or two rotary tables (A11, A22) or/and a second spindle (C22).
When all the possible machine axes for the series are declared, all the axis data
blocks are also set up in the PLC (DB 31 – 38).
The axis assignment remains the same, regardless of which axes are actually
on the machine.
This is the requirement for a standardized PLC program.
Machine data
N10000 $MN_AXCONF_MACHAX_NAME_TAB[0]=“X11”
N10000 $MN_AXCONF_MACHAX_NAME_TAB[1]=“Y11”
N10000 $MN_AXCONF_MACHAX_NAME_TAB[2]=“Z11”
N10000 $MN_AXCONF_MACHAX_NAME_TAB[3]=“A11”
N10000 $MN_AXCONF_MACHAX_NAME_TAB[4]=“A22”
N10000 $MN_AXCONF_MACHAX_NAME_TAB[5]=“B11”
N10000 $MN_AXCONF_MACHAX_NAME_TAB[6]=“C22”
N10000 $MN_AXCONF_MACHAX_NAME_TAB[7]=“C11”
Axis X
Axis Y
Axis Z
1st rotary table
2nd rotary table
Magazine axis
2nd spindle
1st spindle
Machine data files are set up for the individual machine options. These only
contain the modified machine data.
6-64
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
6.5
Example file
6 Programming the control
Example of a start-up concept
%_N_COMPLETE_TEA_INI;
OPTION 5 AXES [X,Y,Z,A11,B] 1 SPINDLE [C]; Rotary axis A11 with double axis module.
CHANDATA(1);
OPTION 5 AXES 1 SPINDLE
N13000 $MN_DRIVE_IS_ACTIVE[0]=1
N13000 $MN_DRIVE_IS_ACTIVE[1]=1
N13000 $MN_DRIVE_IS_ACTIVE[2]=1
N13000 $MN_DRIVE_IS_ACTIVE[3]=1
N13000 $MN_DRIVE_IS_ACTIVE[4]=1
N13000 $MN_DRIVE_IS_ACTIVE[5]=1
N13000 $MN_DRIVE_IS_ACTIVE[6]=0
N13000 $MN_DRIVE_IS_ACTIVE[7]=0
N13010 $MN_DRIVE_LOGIC_NR[0]=8
N13010 $MN_DRIVE_LOGIC_NR[1]=1
N13010 $MN_DRIVE_LOGIC_NR[2]=3
N13010 $MN_DRIVE_LOGIC_NR[3]=2
N13010 $MN_DRIVE_LOGIC_NR[4]=6
N13010 $MN_DRIVE_LOGIC_NR[5]=4
N13010 $MN_DRIVE_LOGIC_NR[6]=5
N13010 $MN_DRIVE_LOGIC_NR[7]=0
N13030 $MN_DRIVE_MODULE_TYPE[0]=1
N13030 $MN_DRIVE_MODULE_TYPE[1]=2
N13030 $MN_DRIVE_MODULE_TYPE[2]=2
N13030 $MN_DRIVE_MODULE_TYPE[3]=2
N13030 $MN_DRIVE_MODULE_TYPE[4]=2
N13030 $MN_DRIVE_MODULE_TYPE[5]=2
N13030 $MN_DRIVE_MODULE_TYPE[6]=2
N13030 $MN_DRIVE_MODULE_TYPE[7]=9
CHANDATA(1)
N20000 $MC_CHAN_NAME=“Milling machine”
N20070$MC_AXCONF_MACHAX_USED[0]=1
N20070$MC_AXCONF_MACHAX_USED[1]=2
N20070$MC_AXCONF_MACHAX_USED[2]=3
N20070$MC_AXCONF_MACHAX_USED[3]=4
N20070$MC_AXCONF_MACHAX_USED[4]=6
N20070$MC_AXCONF_MACHAX_USED[5]=8
N20070$MC_AXCONF_MACHAX_USED[6]=0
N20070$MC_AXCONF_MACHAX_USED[7]=0
N20080 $MC_AXCONF_CHANAX_NAME_TAB[0]=“X”
N20080 $MC_AXCONF_CHANAX_NAME_TAB[1]=“Y”
N20080 $MC_AXCONF_CHANAX_NAME_TAB[2]=“Z”
N20080 $MC_AXCONF_CHANAX_NAME_TAB[3]=“A1”
N20080 $MC_AXCONF_CHANAX_NAME_TAB[4]=“B1”
N20080 $MC_AXCONF_CHANAX_NAME_TAB[5]=“C1”
N20080 $MC_AXCONF_CHANAX_NAME_TAB[6]=“”
N20080 $MC_AXCONF_CHANAX_NAME_TAB[7]=“”
M17
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-65
6
03/2006
6 Programming the control
6.5 Example of a start-up concept
Sequence for
initial start-up
1. Read in streamer tape with all the machine option files
2. Start the standard system start-up file for the basic machine in the Services/
Archive area
3. Start the PLC standard system start-up file
4. Start the machine option file (e.g. for 6 axes), NCK reset
5. Set the PLC options in the PLC dialog
When these steps are complete, the machine is in full working order with the
basic data.
Time required:
6
Size of the tool
magazine
1 hour
The files for the machine options also include the size of the tool magazine
(36, 48, ..places).
N10900 $MN_INDEX_AX_LENGTH_POS_TAB_1=36
N10910 $MN_INDEX_AX_POS_TAB_1[0]=0
N10910 $MN_INDEX_AX_POS_TAB_1[1]=10
N10910 $MN_INDEX_AX_POS_TAB_1[2]=20
.........
Axis scan/
corrections
The next initial start-up step is to scan the axes and for the mechanic or test
engineer to enter the relevant corrections (e.g. batches).
Suitable user screens may be created in the “Start-up/Machine data” area to
make this easier to use.
Example: User screens “MECHANIC” and “QSK”
Data back-up
Once the initial start-up is completed, all the data is saved to a standard system
start-up file. This file is then specifically for the machines that have been
brought into service and can be used later if there are any problems in restoring
the machine to its as-delivered state.
The files in the Services/Archive area for the basic machine and machine
options are no longer required and are therefore deleted.
The correction data (e.g. spindle pitch) is saved separately from the Services/
Active NCK data area to the archive.
The last step in the start-up is to stream off all the HMI data.
6-66
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.6 System data
03/2006
6.6
System data
6.6.1
Basic settings
Control clock
cycles
The control works on the basis of clock cycles that are defined via machine
data. The system basic cycle is specified in seconds; the other cycle times are
obtained as multiples of the system basic cycle.
The clock cycles are optimized by default and should only be changed if the
requirements of the NCK cannot be met with the default values.
The following cycle times are used by default:
Table 6-10
Clock cycles – default values for the control
840D
NCU 571
Cycle
*
#
840D
NCU 572
840D
NCU 573
6
Setting via MD
System basic
cycle in s
6 ms
4 ms
4* / 8# ms
MD 10050: SYSCLOCK_CYCLE_TIME
Position control
cycle as a factor
6 ms
4 ms
4* / 8# ms
MD 10060: POSCTRL_SYSCLOCK_TIME_RATIO
Interpolator cycle as a factor
18 ms
12 ms
12* / 40# ms
MD 10070: IPO_SYSCLOCK_TIME_RATIO
with 2 channel and 12 axes
with > 2 channels
General example
for cycle settings
The machine data for cycle times is set as follows:
If MD ... = ...
!
Switching from
metric to Inch
Then the ... = ...
SYSCLOCK_CYCLE_TIME = 0.002
System basic cycle = 2 ms
POSCTRL_SYSCLOCK_TIME_RATIO = 1
Position control cycle = 2 ms (1 2 ms)
IPO_SYSCLOCK_TIME_RATIO = 3
Interpolator cycle = 6 ms (3 2 ms)
Warning
If you have changed the clock cycles, check that the operating response of the
control is correct in all operating modes before ending the start-up process.
A control is switched from the metric system to an inch system with
MD 10240: SCALING_SYSTEM_IS_METRIC (basic system is metric).
The additional conversion factor is specified in
MD 10250: SCALING_VALUE_INCH (conversion factor for switching to the
INCH system, factor = 25.4).
After power ON the existing data is converted to inches and displayed. After
switchover data must be entered in inches.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-67
03/2006
6 Programming the control
6.6 System data
It is also possible to switch the scaling system via MD 10260.
Requirement:
S Set MD 10260: CONVERT_SCALING_SYSTEM=1
S Bit 0 of MD 20110: RESET_MODE_MASK is set in each channel
S Automatic conversion of NCK active data when the scaling system is
changed.
S Data backup with detection of current system of units.
S Effect of MD 10240: SCALING_SYSTEM_IS_METRIC is reset.
S Configuring of the scaling system for sag compensation via MD 32711:
CEC_SCALING_SYSTEM_METRIC.
The programmed basic settings can be changed over (G70, G71, G700, G710)
for specific channels in MD 20150: GCODE_RESET_VALUES [12]. If the soft
key is used to change via the HMI, the value toggles between G700 (inch) and
G710 (metric).
6
With G700/G710, additional feeds (inch/min or mm/min) are interpreted in the
scaling system, in addition to the specified lengths.
Internal physical
variables
The physical variables in the machine data are set to the following units by
default:
Bit no./Physical variable
0 Linear position
1 Angular position
2 Linear velocity
3 Angular velocity
4 Linear acceleration
5 Angular acceleration
6 Linear jerk
7 Angular jerk
8 Time
9 Position controller loop gain
10 Feedrate per revolution
11 Linear position (correction value)
12 Angular position (correction value)
13 Cutting speed
Physical variables
for input/output
metric
1 mm
1 degree
1 mm/min
1 rpm
1 m/s2
1 rev./s2
1 m/s3
1 rev./s3
1s
1/s
1 mm/rev.
1 mm
1 degree
1 m/min
inch
1 inch
1 degree
1 inch/min
1 rpm
1 inch/s2
1 rev./s2
1 inch/s3
1 rev./s3
1s
1/s
1 inch/rev.
1 degree
1 degree
1 foot/min
The physical variables for the input/output of machine and setting data may be
defined across the system via
MD10220: SCALING_USER_DEF_MASK (activates the scaling factors) and
MD 10230: SCALING_FACTORS_USER_DEF (scaling factors for the physical
variables).
If the corresponding activation bit is not set in MD 10220, then the scaling takes
place internally with the conversion factors listed below (default setting,
exception KV factor).
If all the bits are set in MD 10220 and the default setting is to be retained, then
the following scaling factors must be entered in MD 10230.
6-68
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.6 System data
03/2006
Index No.
Physical variable
Input/output
Internal unit
Scaling factor
0
Linear position
1 mm
1 mm
1
1
Angular position
1 degree
1 degree
1
2
Linear velocity
1 mm/min
1 mm/s
0.016666667
3
Angular velocity
1 rev/min
1 degree/s
6
4
Linear acceleration
1 m/s2
1 mm/s2
1000
5
Angular acceleration
1 rev/s2
1 degree/s2
360
m/s3
mm/s3
1000
6
Linear jerk
1
7
Angular jerk
1 rev/s3
1
1 degree/s3
360
8
Timer
1s
1s
1
9
Position controller loop gain
1 m/min∗mm
1/s
16.66666667
10
Revolutional feedrate
1 mm/rev
1 mm/degree
1/360
11
Linear position (compensation value)
1 mm
1 mm
1
12
Angular position (compensation value)
1 degree
1 degree
1
13
Cutting velocity
1 m/min
1 m/min
1
6
Input values for machine data
MD 10220
Scaling factor
activated?
no
Internal scaling
yes
MD 10230
Scaling factor
Internal physical variable
Fig. 6-2
Example
Changing physical variables
In our example the user wishes to enter the linear velocity in m/min.
The internal physical variable is mm/s.
The scaling factor is calculated using the following formula:
1 m * 1000 mm * 1 min
[m/min] =
= 1000/60 [mm/s] = 16.666667
min * 1 m * 60 s
The machine data must be entered as follows:
MD 10220: SCALING_USER_DEF_MASK = ‘H4’ (activates the new factor) and
MD 10230: SCALING_FACTORS_USER_DEF [2] = 16.6666667 (scaling factor
for linear velocity in m/min)
The machine data is automatically converted to these physical variables after
input of the new scale and power ON. The new values are displayed and can
then be saved.
The unit of the physical variables for programming in the part program is
specified in the Programming Guide.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-69
6 Programming the control
6.6 System data
Internal Calculation resolution
03/2006
The internal calculation resolutions for the control are entered in MD 10200:
INT_INCR_PER_MM (calculation resolution for linear positions) and MD 10210:
INT_INCR_PER_DEG (calculation resolution for angular positions).
The default value for this machine data is “1000”. The control thus calculates as
standard in 1/1000 mm or 1/1000 degrees. If greater accuracy is required, only
these two machine data need to be changed. It is useful to enter machine data
in powers of 10 (100, 1000, 10000). Rounding if required (and thus also
falsification) of the internal values can only be achieved using smaller units.
However, it is essential that the measuring system is adapted to this degree of
accuracy. The internal calculation resolution also determines the accuracy with
which positions and selected compensation functions are calculated. Changes
to the MD have no influence on the velocities and cycle times which can be
attained.
6
Display resolution
The number of decimal places for the position values on the front operating
panel should be set in MD 9004: DISPLAY_RESOLUTION.
Limit values for
input and display
The limits placed on input values depends on the display option and on the
input options on the front operating panel.
This limit is reached at 10 digit positions plus decimal point plus sign.
Reference material
6-70
/FB1/ G2, Basic machine functions manual,
Section “Input/display resolution, calculation resolution”
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.7 Memory configuration
03/2006
6.7
Memory configuration
Hardware structure
The following table shows the hardware structure of the available NCK CPU:
D-RAM
S-RAM
PCMCIA
NCU 561.4
32 MB
4 MB
8 MB
NCU 571.3
2 x 4 MB
4 MB
8 MB
NCU 571.4
32 MB
4 MB
8 MB
NCU 572.3
32 MB
2 MB
8 MB
NCU 572.4
32 MB
4 MB*
8 MB
NCU 573.4
64 MB
4 MB
8 MB
NCU 573.5
64 MB*
3 MB*
8 MB
6
*) Can be ordered as options, see Catalog NC 60
Memory areas
The memory areas for user data in the NCK are set to the appropriate defaults
after an NCK general reset. The following areas can be adjusted to achieve
optimum utilization of the available RAM:
S Part programs
S Tool management
S Tool offsets
S Global user data
S Curve tables
S Compensations (e.g. LEC)
S File system/program memory
S Protection areas
The memory breakdown must take place before the NC is actually started up
since, if it is divided up again, all the buffered user data will be lost (e.g. part
programs, drive data).
Machine data, setting data and options are not erased.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-71
03/2006
6 Programming the control
6.7 Memory configuration
Effectiveness
!
The machine data for the memory configuration takes effect at Power-On.
Caution
Before increasing the size of DRAM areas (e.g. local user variables or function
parameters), first check whether the available memory is sufficient (MD 18050
must be greater than 15000). If more dynamic memory is required than is
available, then at the next power-up, the SRAM will be deleted as well without
warning and the following user data will be lost:
–
–
–
–
6
Drive machine data
Part programs
Memory configuration data
Configurable memory areas
Reference material:
Displaying and
editing system
resources
/FB 2/ S2, Description of the extended functions,
memory configuration,
Section: Determining the memory required.
The HMI user interface can be used to display the system resources currently in
use in the NCK and HMI areas. They can also be edited if the user has the necessary access rights.
Procedure:
Press the “Start-up” soft key on the HMI user interface.
The “NC memory” soft key also appears when the Extended key is pressed.
When the soft key is pressed, an overview of the current RAM allocation is
displayed:
S Static RAM (SRAM)
S Dynamic RAM (DRAM)
To view the memory for configured machine data in greater detail, further areas
can be displayed by pressing the “SRAM” or “DRAM” soft keys.
Reference material:
6-72
/IAM/ IM2, Start-up Guide, HMI Embedded,
Section: Displaying and editing system resources
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.7 Memory configuration
03/2006
6.7.1
Dynamic RAM
Set the following machine data:
Table 6-11
MD for DRAMmemory breakdown
MD for DRAM
Meaning
MD 18242: MM_MAX_SIZE_OF_LUD_VALUE
This data is set to 8192 bytes for “cycle 95”.This MD can be
reduced to 2048 if cycle 95 is not used.
MD 18351: MM_DRAM_FILE_MEM_SIZE
Size of the part program memory in DRAM
MD 28040: MM_LUD_VALUE_MEM
Memory size for local user variables.
Do not increase this MD 28040 from 25 kByte (default
setting) to 35–50 kByte unless you need more than
2048 bytes in MD 18242.
6
Checking the
DRAM
6.7.2
Check the free DRAM against MD18050. Values greater than 15000 must be
displayed. If the value is smaller, the memory resources are exhausted and
there is a risk that user data will be lost if DRAM continues to be allocated.
Static RAM
Set the following machine data:
Table 6-12
MD for SRAM breakdown
MDs for SRAM
Meaning
MD 18120: MM_NUM_GUD_NAMES_NCK
Number of global user variables
MD 18130: MM_NUM_GUD_NAMES_CHAN
Number of channel-specific global user variables
MD 18080: MM_TOOL_MANAGEMENT_MASK
Memory breakdown for tool managementSet the tool management to suit the requirements of the machine. If you are
not using the TM function, set MD 18084 and 18086 to “0”
to free more memory for part programs.
MD 18082: MM_NUM_TOOL
Number of tools according to machine
MD 18100: MM_NUM_CUTTING_EDGES_IN_TOA
Number of tool cutting edges per TOA module according to
requirements of end customer
MD 18160: MM_NUM_USER_MACROS
Number of macros
MD 18190: MM_NUM_PROTECT_AREA
MD 28200: MM_NUM_PROTECT_AREA_CHAN
MD 28210: MM_NUM_PROTECT_AREA_ACTIV
Number of files for machine-related protection areas
Number of files for channel-specific protection areas
Number of protected areas on a channel that are active at
the same time
MD 28050: MM_NUM_R–PARAM
Number of R parameters required
MD 28080: MM_NUM_USER_FRAMES
Number of frames required
MD 38000: MM_ENC_COMP_MAX_POINTS
Number of compensation points required
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-73
03/2006
6 Programming the control
6.7 Memory configuration
SRAM with
2 MB module
If the NCU is used with a larger memory, this memory must be enabled.
S Enter the value 1900 in MD 18230: MM_USER_MEM_BUFFERED.
S Stream off a standard system start-up file.
S POWER ON (to reorganize the memory).
S Download the standard system start-up file to the control once more.
Check SRAM
MD 18060 shows how much RAM is still free.
Recommendation:
Values > 15000 should be displayed so that data (e.g. tool offsets) can be read
in at any time.
6
Note
For normal applications, leave all other memory settings unchanged.
Deleting SRAM by
changing the MD
Table 6-13
Changing the following machine data causes the control SRAM to be
reconfigured. In the event of a change, the “4400 MD change caused
reorganisation of the buffered memory (data lost!)” alarm is output. When this
alarm is output, all data must be saved because all buffered user data will be
erased during the next booting.
Machine data for the memory configuration
MD Number
MD name
Meaning
MD 18020
MM_NUM_GUD_NAMES_NCK
Number of global user variables
MD 18030
MM_NUM_GUD_NAMES_CHAN
Number of global user variables
MD 18080
MM_TOOL_MANAGEMENT_MASK
Tool management memory
MD 18082
MM_NUM_TOOL
Number of tools
MD 18084
MM_NUM_MAGAZINE
Number of magazines
MD 18086
MM_NUM_MAGAZINE_LOCATION
Number of magazine locations
MD 18090
MM_NUM_CC_MAGAZINE_PARAM
Number of magazine data items
MD 18092
MM_NUM_CC_MAGLOC_PARAM
Number of magazine location data items
MD 18094
MM_NUM_CC_TDA_PARAM
Number of tool-specific data items
MD 18096
MM_NUM_CC_TOA_PARAM
Number of TOA data items
MD 18098
MM_NUM_CC_MON_PARAM
Number of monitoring data items
MD 18100
MM_NUM_CUTTING_EDGES_IN_TOA
Number of cutting edges per TOA block
MD 18110
MM_NUM_TOA_MODULES
Number of TOA blocks
MD 18118
MM_NUM_GUD_MODULES
Number of GUD files
MD 18120
MM_NUM_GUD_NAMES_NCK
Number of global user variables
MD 18130
MM_NUM_GUD_NAMES_CHAN
Number of channel-specific user variables
MD 18140
MM_NUM_GUD_NAMES_AXIS
Number of axis-specific user variables
MD 18150
MM_GUD_VALUES_MEM
Memory location for user variables
MD 18160
MM_NUM_USER_MACROS
Number of macros
6-74
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.7 Memory configuration
03/2006
Table 6-13
MD Number
Machine data for the memory configuration
MD name
Meaning
MD 18190
MM_NUM_PROTECT_AREA_NCKC
Number of protected areas
MD 18230
MM_USER_MEM_BUFFERED
RAM in SRAM
MD 18270
MM_NUM_SUBDIR_PER_DIR
Number of subdirectories
MD 18280
MM_NUM_FILES_PER_DIR
Number of files
MD 18290
MM_FILE_HASH_TABLE_SIZE
Hash table size for files in a directory
MD 18300
MM_DIR_HASH_TABLE_SIZE
Hash table size for subdirectories
MD 18310
MM_NUM_DIR_IN_FILESYSTEM
Number of directories in the passive file system
MD 18320
MM_NUM_FILES_IN_FILESYSTEM
Number of files in the passive file system
MD 18330
MM_CHAR_LENGTH_OF_BLOCK
Max. length of an NC block
MD 18350
MM_USER_FILE_MEM_MINIMUM
Minimum RAM in SRAM
MD 28050
MM_NUM_R_PARAM
Number of channel-specific R parameters
MD 28080
MM_NUM_USER_FRAMES
Number of variable frames
MD 28085
MM_LINK_TOA_UNIT
Allocation of a TO unit to a channel
MD 28200
MM_NUM_PROTECT_AREA_CHAN
Number of files for protection areas
MD 38000
MM_ENC_COMP_MAX_POINTS [n]
Number of interpolating point for interp. compensation
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6
6-75
03/2006
6 Programming the control
6.8 Scaling machine data
6.8
Scaling machine data
Download scaling
machine data
The machine data also includes data that defines the scaling of machine data in
relation to its physical unit (e.g. velocities).
This is in relation to the scaling for the following machine data, for example:
S MD 10220: SCALING_USER_DEF_MASK (activates the scaling factors)
S MD 10230: SCALING_FACTORS_USER_DEF (scaling factors for the physical variables)
S MD 10240: SCALING_SYSTEM_IS_METRIC (basic system is metric)
S MD 10250: SCALING_VALUE_INCH (conversion factor for switching to the
6
INCH system)
S MD 30300: IS_ROT_AX (rotary axis)
When machine data is loaded (via HMI, RS-232 interface, program), it is scaled
according to the physical unit which is currently valid. If this record contains a
new scaling (e.g. a rotary axis declaration), then the machine data that is dependent on the scaling will be converted to the new scaling at the next POWERON. The MD then does not contain the expected values (e.g. rotary axis traverses at very low F values).
Example:
The control was started up with default values. The MD file to be downloaded
defines the 4th axis as a rotary axis and contains the following machine data:
$MA_IS_ROT_AX[A1] = 1 (rotary axis)
$MA_MAX_AX_VELO [A1]= 1000 [rev./min] (maximum axis speed)
When the MD block is downloaded, the velocity is interpreted in relation to a
linear axis (default setting $MA_IS_ROT_AX[A1]=0 ) and scaled to the linear
velocity.
During the next Power-on process, the control detects that this axis is defined
as a rotary axis and normalizes the velocity with reference to rev/min. The value
in the machine data is then no longer “1000”, but “2.77777778” (1000/360).
If the machine data file is downloaded again, the axis is already defined as a
rotary axis and the velocity is interpreted and scaled as a rotary axis velocity,
The MD then contains the value “1000” that is interpreted in rev/min by the control system.
Gradual downloading
of machine data
Either
S Change the relevant machine data manually via HMI (MD 10220, 10230,
10240, 10250, 30300) and then power-up the NCK. Then read in the MD
record and trigger the NCK power-up, or
S Generate an MD record with the scaling machine data (MD 10220, 10230,
10240, 10250, 30300). Load this MD record and initiate an NCK power-up.
Then read in the complete MD record and trigger the NCK power-up, or
S Alternatively, an MD record may be downloaded twice, each time with an
NCK power-up.
6-76
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.8 Scaling machine data
03/2006
Note
If a scaling MD is altered, then the control outputs alarm “4070 Scaling data
changed”.
Download
standard data
Standard machine data can be downloaded in different ways.
S Turn switch S3 on the NCU module to position 1 and reset the NCK.
Note
This will reinitialize the entire SRAM of the NCU module. All the user data will
be lost.
S MD 11200: INIT_MD (download standard MD at “next” power-up)
Via certain input values in the MD: INIT_MD can be downloaded with standard
values to various data areas at the next NCK power-up. The machine data is
displayed in HEX format. After setting the MD: INIT_MD must initiate a POWERON twice.
S The MD is activated at the 1st power-on.
S The 2nd power-on executes the function and resets the MD to the value “0”.
Significance of the
input values in
MD 11200
Value “0”
The saved machine data is downloaded at the next power-up.
Value “1”
All the MDs, apart from the memory-configuring data, are overwritten with the
default values at the next power-up.
Value “2”
All memory-configuring MDs are overwritten with the default values at the next
power-up.
Value “4”
Reserved
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-77
6
03/2006
6 Programming the control
6.9 Axes and spindles
6.9
Axes and spindles
6.9.1
Description of the axis configuration
The SINUMERIK 840D is supplied as standard with the following configuration:
S NCU 571:
1 channel and 5 axes.
S NCU 572/573:
2 channels and 8 axes with simulated setpoint and
actual value channels.
Note
6
With SINUMERIK 840D, this depends on the hardware/software version
up to 12 axes/spindles are permitted
per channel
up to 31 axes or 20 spindles are permitted
per NCU
Reference material:
/BU/ Order documents, catalog NC 60
If DMP compact modules are used, then the number of axes, including DMP
modules, is limited to 31 in the axis configuration with NCU 573.3. If a DMP
compact module is used with 31-axis software, for example, then there are
30 axes available.
Number of
channels
With the SINUMERIK 840D there are >2 channels available.
Machine axes
This means all the axes present on the machine. They are defined as geometry
axes or special axes.
Geometry axes
The workpiece geometry is programmed with the geometry axes. The geometry
axes form a rectangular coordinate system (2D or 3D).
Special axes
Unlike geometry axes, there is no geometrical connection for special axes,
e.g. for:
– Rotary axes
– Revolver axes
– Position-controlled spindles
Axis configuration
The axis configuration is defined on three levels:
1. Machine level
2. Channel level
3. Program level
6-78
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
1. Machine level
MD 10000: AXCONF_MACHAX_NAME_TAB
Here, an axis name is defined in
MD 10000: AXCONF_MACHAX_NAME_TAB for each machine axis.
Example:
Lathe
with X, Z, C axis/spindle
MD 10000
Index
X1
Z1
C1
0
1
2
Milling machine
4 axes+spindles/C axis
3
4
X1
Y1
Z1
A1
C1
0
1
2
3
4
Example for a milling machine: MD10000
AXCONF_MACHAX_NAME_TAB[0] = X1
AXCONF_MACHAX_NAME_TAB[1] = Y1
AXCONF_MACHAX_NAME_TAB[2] = Z1
AXCONF_MACHAX_NAME_TAB[3] = A1
AXCONF_MACHAX_NAME_TAB[4] = C1
6
2. Channel level
S MD 20070: AXCONF_MACHAX_USED[0...7]
The channel-specific MDs are used to assign the machine axes to
a geometry channel.
Lathe
1
Milling machine
2
3
0
0
1
2
3
4
5
S MD 20080: AXCONF_CHANAX_NAME_TAB[0...7]
The MD defines the names of the axes on the channel. Enter the names of
the geometry and additional axes here.
X
Z
C
X
Y
Z
A
C
3. Program level
S MD 20060: AXCONF_GEOAX_NAME_TAB[0...2]
The MD defines the names that are used in the part programs for the geometry axes (machine-independent workpiece axes).
X
Y*
Z
X
Y
Z
* For a transformation e.g. TRANSMIT
the 2nd geometry coordinates must also
be given a name (e.g. “Y”)
S MD 20050: AXCONF_GEOAX_ASSIGN_TAB[0...2]
Defines the allocation of geometry axes to the axes of the channel
(MD20070) without transformation. For allocation while transformation is
active, see:
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-79
03/2006
6 Programming the control
6.9 Axes and spindles
Reference material: /FB1/ K2, Functional description of the basic machines,
Axes, coordinate systems, frames
Note the relationship with the inclusion of tool offsets in the calculation (G17,
G18, G19).
1
0
2
1
2
3
During program execution, the coordinates that are not assigned via
MD 20060/MD 20050 are always mapped directly onto the axes of the channel
(in the milling machine example below, axes A and C).
6
Machine axis no. for channel
1
2
3
4
5
MD 20070: AXCONF_MACHAX_USED
Machine axes used on the channel
AXCONF_MACHAX_USED[0]=1
AXCONF_MACHAX_USED[1]=2
AXCONF_MACHAX_USED[2]=3
AXCONF_MACHAX_USED[3]=4
AXCONF_MACHAX_USED[4]=5
A C
Axis name on the channel (special axes)
MD 20080: AXCONF_CHANAX_NAME_TAB
Names of the special axes on the channel (for use in
the part program)
AXCONF_CHANAX_NAME_TAB [0]=
AXCONF_CHANAX_NAME_TAB [1]=
AXCONF_CHANAX_NAME_TAB [2]=
AXCONF_CHANAX_NAME_TAB [3]=A
AXCONF_CHANAX_NAME_TAB [4]=C
MD 20050: AXCONF_GEOAX_ASSIGN_TAB
Allocation of GEOaxis to axes on the channel.
AXCONF_GEOAX_ASSIGN_TAB [0]=1
AXCONF_GEOAX_ASSIGN_TAB [1]=2
AXCONF_GEOAX_ASSIGN_TAB [2]=3
X to X, Y to Y, Z to Z
Assignment of
GEO axes
X Y Z
GEO axis
A
C
Special axes
Names of the GEO axes
MD 20060: AXCONF_GEO_AX_NAME_TAB[0]=X
MD 20060: AXCONF_GEO_AX_NAME_TAB[0]=Y
MD 20060: AXCONF_GEO_AX_NAME_TAB[0]=Z
Fig. 6-3
6-80
Example of milling machine: 4 axes + spindle/C axis
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
Define axis
identifier
The name defined in MD 10000: AXCONF_MACHAX_NAME_TAB or the
associated index is used for:
S Accessing axis-specific machine data (loading, saving, displaying)
S Reference point approach G74
S Measurements
S Test point runs G75
S Traversing commands from PLC
S Display of axis-specific alarms
S Display of actual-value system (machine-related)
S DRF handwheel function
6
Note
Leading zeros are generally ignored in user-defined axis identifiers.
Examples:
MD 10000: AXCONF_MACHAX_NAME_TAB[0] = X01 corresponds to X1
MD 10000: AXCONF_MACHAX_NAME_TAB[1] = A01 corresponds to A1
MD 10000: AXCONF_MACHAX_NAME_TAB[2] = C01 corresponds to C1
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-81
03/2006
6 Programming the control
6.9 Axes and spindles
6.9.2
Drive configuration (VSA, SLM, HSA)
Note
The drive configuration and start-up of synchronous linear motors (SLM) are
described in the next section.
There are no drive parameters stored in the control in the delivery state or after
a general reset.
Before the drives can be programmed, the drive structure available on the
control (power sections and motors) must first be entered and the axes declared
with MD 20070: AXCONF_MACHAX_USED/
MD 10000: AXCONF_MACHAX_NAME_TAB must be allocated.
6
Fig. 6-4
Drive configuration screen with HMI Advanced
Note
The settings made in the “Drive configuration” screen are described individually
below.
Setting the drive
configuration
The drive configuration is entered in the “Drive configuration” screen using the
operating panel or at the 611D Start-up Tool. The screen is accessed using the
“Machine data” –> “Drive configur.” soft keys.
S Each power section is physically assigned a slot number.
S If a slot is not used or if it does not contain a power section, then it should be
identified as passive.
S A logical address via which the relevant drive is addressed (setpoint/actual
value assignment, access to parameters) is assigned to each slot used.
6-82
 Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
Power section
selection
Once you have defined the drive type (VSA, SLM, HSA), you must then select
the associated power section.
This can be defined by:
–
Entering the power section code directly (e.g. from Table 6-9)
–
Selecting from the power section list (MLFB numbers) stored on the control using the “Pow.sect.sel...” vertical soft key, selecting the power section using the cursor keys, then press the “OK” soft key to confirm and
then automatically returning to the configuration screen.
Requirement: The cursor must be on the same line as the
desired slot.
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
Table 6-14
Drive type
Allocating the drive/power section/power section code
Amperage
Power
section
Code
MSD
3/3/3A
8A
01
MSD
5/5/8A
15 A
02
MSD
8 / 10 / 16 A
25 A
04
MSD
24 / 32 / 32 A
50 A
06
MSD
30 / 40 / 51 A
80 A
07
MSD
45 / 60 / 76 A
108 A
0D
MSD
45 / 60 / 76 A
120 A
08
MSD
60 / 80 / 102 A
160 A
09
MSD
85 / 110 / 127 A
200 A
0A
MSD
120 / 150 / 193 A
300 A
0B
MSD
200 / 250 / 257 A
400 A
0C
FDD
3/6A
8A
11
FDD
5 / 10 A
15 A
12
FDD
9 / 18 A
25 A
14
FDD
18 / 36 A
50 A
16
FDD
28 / 56 A
80 A
17
FDD
56 / 112 A
160 A
19
FDD
70 / 140 A
200 A
1A
FDD
140 / 210 A
400 A
1C
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-83
6
03/2006
6 Programming the control
6.9 Axes and spindles
Example 1
of a machine
SINUMERIK 840D with 3 axes and one spindle
Z1 axis
Machine axis name
C1
X1
Y1 Z1
Logical drive no.
4
1
2
Mains NCU
supply momodule
dule
6
HSA
module
VSA
module
VSA
2-axis
module
80 A
50 A
2x25A
1
2
3
Axis
Linear scale
4
Example 1 of a SINUMERIK 840D with 3 axes and 1 spindle
Table 6-15
Data for the example in the figure above:
Slot
Power section module
Drive
Logical drive
no.
Direct
measuring
system
Position
measuring
system 1
Position
measuring
system 2
1
80 A
MSD
4
no
Motor encoder
no
2
50 A
FDD
1
no
Motor encoder
no
3
25 A
FDD
2
no
Motor encoder
no
4
25 A
FDD
3
yes
Linear scale
no
Fig. 6-6
6-84
Gearing
The encoder
G is always
present on
611D
Module slots
Fig. 6-5
M
3
Drive configuration
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
6.9.3
Programming axis-specific setpoint/actual values
Assigning the setpoint/actual value
channels
A setpoint value channel (i.e. a logical drive number) and at least one actual
value channel must be assigned to each axis/spindle for the position measuring
system. An optional second channel may be specified for a second position
measuring system.
The motor measuring system is always used for the speed regulation (X411).
The following fixed assignment is used between the motor connection and the
motor measuring system connection: The motor and motor measuring system
must always be connected to the same module.
Assigning the setpoint channel (axis-specific)
MD
Meaning
6
Input for example 1 (see Fig. 6-6)
MD 30110:
CTRLOUT_MODULE_NR
Assignment of a logical drive no.
to setpoint channel
X1=“1”
Y1=“2”
Z1=“3”
C1=“4”
MD 30130: CTRLOUT_TYPE
Setpoint channel exists
“1”
Slot 2
Slot 3
Slot 4
Slot 1
Assignment actual value channel (axis-specific)
MD
MD 30200: NUM_ENCS
Meaning
Number of measuring channels
“1” if there is just one position
measuring system
Input for example 1
X1=“1”
Y1=“1”
Z1=“1”
C1=“1”
(“2” if there are two position measuring systems)
MD 30240: ENC_TYPE[0]
Encoder type
“1” for incremental encoders
(“4” for absolute encoders with
EnDat interface)
MD 30220:
X1=“1”
Y1=“1”
Z1=“1”
C1=“1”
Allocation of a logical drive no. to
the actual value channel for position measuring system 1
X1=“1”
Y1=“2”
Z1=“3”
C1=“4”
Allocation of a logical drive no. to
the actual value channel for position measuring system 2
Position measuring system 2 is not used
MD 30230: ENC_INPUT_NR[0]
Allocation for position measuring
system 1
“1” for motor measuring system
“2” for direct measuring system
X1=“1”
Y1=“1”
Z1=“2”
C1=“1”
MD 30230: ENC_INPUT_NR[1]
Allocation for position measuring
system 2
Position measuring system 2 is not used
ENC_MODULE_NR[0]
MD 30220:
ENC_MODULE_NR[1]
Slot 2
Slot 3
Slot 4
Slot 1
“1” for motor measuring system
“2” for direct measuring system
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-85
6 Programming the control
6.9 Axes and spindles
03/2006
Note
Each logical drive number may be entered only once in the configuration display. All activated slots must be assigned to an axis (setpoint channel).
If axes/spindles are to remain switched off temporarily during start-up, then
MD 30240: ENC_TYPE, MD 30130 CTRLOUT_TYPE should be set to “0” and
the assigned power section slot should be declared as passive.
The default setting for MD 30100: CTRLOUT_SEGMENT_NR=1, MD 30210:
ENC_SEGMENT_NR =1 should be retained.
MD 30350: SIMU_AX_VDI_OUTPUT can be used to select whether the interface signals of a simulated axis should be output at the PLC interface (e.g. for
testing programs when there is no drive hardware present).
6
Restart
Once the drive configuration and setpoint/actual value assignment have been
entered, NCK reset must be used to restart the control so that the set configuration can take effect.
The message “Start-up required” appears for all activated drives, prompting to
set the drive data parameters.
6-86
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
6.9.4
Setting drive parameters (FDD, MSD)
Setting drive
parameters
A motor type should be set for all drives via the control panel or SIMODRIVE
611 Start-up Tool using the”Machine data FDD” or “Machine data MSD” menu
(see vertical soft key bar). The type is selected from a list via the motor MLFB
(1FT6VVV-VVVV, 1FT7VVV-VVVV, 1PHVVV-VVVV see rating plate).
S For FDD, only the selection of motor 1 is visible.
S For MSD, the choice of motor 1 and motor 2 can be seen (e.g. for switching
between Y/D), while for the Performance 2 controller, there are 4 motor
records available.
To avoid setting the MSD parameters incorrectly, the “OK” soft key remains
disabled until a valid motor or a non-Siemens motor is selected for motor 1.
S After selecting the motor, press the “OK” soft key to confirm and a menu for
entering the encoder data appears.
S The most important control data is assigned defaults when the motor type is
selected.
Acknowledge the “Motor selection” screen and the “Measuring system data”
screen appears.
Fig. 6-7
Example of measuring system data for the motor selection for FDD
This screen is used to select the measuring system used in the motor: incremental encoder or absolute encoder with EnDat interface. Once the measuring
system is selected, all the other necessary values are filled in automatically.
Press “OK” to confirm these.
Example:
S Incremental motor encoder (ERN1387)
1FV6VVV-VVVV-VAVV
Incremental with zero marker: Press “OK” to accept the screen, since the
other parameters are set to the correct defaults for standard motors.
S Absolute motor encoder (EQN1325)
1FV6VVV-VVVV-VEVV
EnDat interface: Press “OK” to accept the screen, since the other parameters are set to the correct defaults for standard motors.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-87
6
6 Programming the control
6.9 Axes and spindles
03/2006
Note
For 1FK6 motors with optical encoders, optimum torque utilization is supported
by automatic identification methods. Traversing motions <5 degrees are not
exceeded mechanically. The identification procedure is performed on every
power-up.
Non-Siemens motor
6
If a non-Siemens motor is used, press the “Non-Siemens motor” soft key to
open the menu for entering the non-Siemens motor data. When you have entered the data and returned to the motor selection menu, “Non-Siemens motor”
is automatically entered in the checkbox for motor 1 or motor 2.
Reference material:
/FBA/ DM1, Functional description for basic machines,
Calculating motor, power section and controller data
Once the motor has been selected, the drive record must be saved for each
axis/spindle using the “Save boot file” operation. The record is saved as a file
VSAxx.BOT or HSAxx.BOT in the RAM (SRAM) of the NC module.
6-88
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
6.9.5
Parameter settings for incremental measuring systems
Rotary encoders
Table 6-16
The following table lists all the parameters which have to be entered for encoder
adjustment.
Machine data for matching rotary encoders
Linear axis
Machine data
Rotary axis
Encoder on
motor
Encoder on
machine
Encoder on
motor
Encoder on
machine
30300: IS_ROT_AX
0
0
1
1
31000: ENC_IS_LINEAR
0
0
0
0
31040: ENC_IS_DIRECT
0
1
0
1
31020: ENC_RESOL
Marks/rev
Marks/rev
Marks/rev
Marks/rev
31030: LEADSCREW_PITCH
mm/rev
mm/rev
–
–
31080: DRIVE_ENC_RATIO_NUMERA
Motor rev.
Load rev.
Motor rev.
Load rev.
31070: DRIVE_ENC_RATIO_DENOM
Encoder rev.
Encoder rev.
Encoder rev.
Encoder rev.
31060: DRIVE_AX_RATIO_NUMERA
Motor rev.
Motor rev.
Motor rev.
Motor rev.
31050: DRIVE_AX_RATIO_DENOM
Spindle rev.
Spindle rev.
Load rev.
Load rev.
Linear axis with
rotary encoder at
the motor
ENC_IS_LINEAR=0
n
Encoder
IS_ROT_AX=0
ENC_IS_DIRECT=0
Load
gearbox
Resolver
gearbox
G
M
nMotor
ÍÍÍÍÍ
Machine table
Leadscrew
nSpindle
LEADSCREW_PITCH
ENC_RESOL
DRIVE_AX_RATIO_NUMERA
=
DRIVE_AX_RATIO_DENOM
No. of motor rev.
No. of spindle rev.
DRIVE_ENC_RATIO_NUMERA
Numberofmotorrevolutions
+
Numberofencoderrevolutions
DRIVE_ENC_RATIO_DENOM
Fig. 6-8
Linear axis with motor-mounted rotary encoder
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-89
6
03/2006
6 Programming the control
6.9 Axes and spindles
Linear axis with
rotary encoder at
the machine
DRIVE_AX_RATIO_NUMERA
No. of motor rev.
=
No. of spindle rev.
DRIVE_AX_RATIO_DENOM
ENC_IS_DIRECT=1
ÍÍÍÍÍ
ÍÍÍÍÍ
IS_ROT_AX=0
Machine table
M
Resolver
Gearing
ENC_IS_LINEAR=0
G
Spindle
Load
Gearing
ENC_RESOL
LEADSCREW_PITCH
n
Spindle
DRIVE_ENC_RATIO_NUMERA
DRIVE_ENC_RATIO_DENOM
6
Fig. 6-9
Rotary axis with
rotary encoder at
the motor
=
n
Encoder
No. of spindle rev.
No. of encoder rev.
Linear axis with machine-mounted rotary encoder
ENC_IS_LINEAR=0
ENC_IS_DIRECT=0
n
Encoder
G
IS_ROT_AX=1
n
Load
M
L
n
DRIVE_AX_RATIO_NUMERA
Motor
DRIVE_AX_RATIO_DENOM
ENC_RESOL
DRIVE_ENC_RATIO_NUMERA
=
DRIVE_ENC_RATIO_DENOM
Fig. 6-10
Rotary table
Load
Gearing
Resolver
Gearing
=
No. of motor rev.
No. of load rev.
Number of motor revolutions
Number of encoder revolutions
Rotary axis with motor-mounted rotary encoder
Rotary axis with
rotary encoder at
the machine
n Load
Rotary table
ENC_IS_DIRECT=1
n Encoder
M
L
G
ENC_RESOL
ENC_IS_LINEAR_=0
IS_ROT_AX=1
Load
gearbox
DRIVE_ENC_RATIO_NUMERA
DRIVE_ENC_RATIO_DENOM
Resolver
gearbox
=
No. of load rev.
No. of encoder rev.
DRIVE_AX_RATIO_NUMERA
Number of motor revolutions
+
Number of load revolutions
DRIVE_AX_RATIO_DENOM
Fig. 6-11
Adapting encoders
for linear measuring systems
6-90
Rotary axis with machine-mounted rotary encoder
The following tables list all the data that must be entered for linear measuring
systems.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
Table 6-17
Machine data for adapting encodersfor linear measuring systems
Machine data
Linear axis
MD 30300: IS_ROT_AX
0
MD 31000: ENC_IS_LINEAR
0
MD 31030: LEADSCREW_PITCH
mm/rev
MD 31040: ENC_IS_DIRECT
Encoder on motor: 0
Encoder on the machine: 1
MD 31010: ENC_GRID_POINT_DIST
Graduation
MD 32110: ENC_FEEDBACK_POL
Sign for actual value (control direction)
[1; –1]
MD 31060: DRIVE_AX_RATIO_NUMERA
Motor revolution
MD 31050: DRIVE_AX_RATIO_DENOM
Spindle revolution
6
Linear axis with
linear scale
DRIVE_AX_RATIO_NUMERA
DRIVE_AX_RATIO_DENOM
=
No. of motor rev.
No. of spindle rev.
IS_ROT_AX=0
ÍÍÍÍÍÍ
Machine table
M
Load gearbox
Leadscrew
LEADSCREW_PITCH
Linear scale
ENC_IS_LINEAR=1
ENC_IS_DIRECT=1
ENC_GRID_POINT_DIST (for linear encoder)
ENC_FEEDBACK_POL= [1 or -1]
Fig. 6-12
Linear axis with linear scale
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-91
03/2006
6 Programming the control
6.9 Axes and spindles
6.9.6
Parameter settings for absolute measuring systems
(EnDat interface)
Requirement
TO adapt the absolute encoder to the machine conditions, follow the procedure
described for a rotary or linear incremental encoder.
The following additional axis machine data must be observed for absolute value
encoders:
Table 6-18
Axis machine data for absolute value encoders
Linear absolute value
encoders
Rotary absolute value encoders
6
MD
at the motor
at the machine
at the machine
1005: ENC_RESOL_MOTOR
Marks/rev
(standard motor 2048) *)
–
–
1007: ENC_RESOL_DIRECT
–
Marks/rev
Graduation in [nm]
1011: ACTUAL_VALUE_CONFIG
Bit 3 *)
–
–
1030: ACTUAL_VALUE_CONFIG_DIRECT
–
Bit 3
Bit 3 + Bit 4
34200: ENC_REEP_MODE [n]:
0...max. No. of encoders –1
0
0
0
34220: ENC_ABS_TURNS_MODULO [n]:
0...max. No. of encoders –1
Multiturn resolution
(Standard motor 4096)
Multiturn resolution
–
*)
Measuring system parameters were set automatically when the motor was selected.
Setting up the
absolute encoder
To set the encoder, determine the offset between the machine zero and the zero
of the absolute encoder and save it to the SRAM of the NC module.
The adjusted state is identified by MD 34210: ENC_REFP_STATE = 2.
Reference material:
Readjustment
/FB1/ R1, Functional description of the basic machine,
Reference point approach
When the machine is started up, the absolute encoder must be set up once the
axes are ready to move. However, it may also be necessary to readjust the encoder at a later point in time, e.g.
S after dismantling/installing the encoder or the motor with absolute encoder
or,
S in general if the mechanical connection between the encoder and load was
separated and, when it was joined together again, the remaining deviation is
outside the tolerances
S if data is lost from the SRAM of the NCK, battery power lost, PRESET
S if gearbox is switched between the load and absolute encoder
MD 34210: ENC_REFP_STATE deleted
6-92
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
Note
In all other cases, the user is responsible for switching
MD 34210: ENC_REFP_STATE to “0” or “1” and for carrying out the readjustment.
In the event of “position buffering after power off”, entering REFP_STATE=1
only causes value 2 to change if it has already been referenced.
To exit this mode, REFP_STATE must = 0, otherwise this referenced/adjusted
status is retained forever, even after REFP_MODE and Power Off are changed.
Readjusting the
absolute encoder
Sequence
The following MDs should be noted before adjustment:
MD 34200: ENC_REFP_MODE=0 (for absolute encoder: accept
REFP_SET_POS)
MD 34220: ENC_ABS_TURNS_MODULO (only needed for rotary axes)
6
1. Set MD 30240: ENC_TYPE=4
2. Set MD 34200: ENC_REFP_MODE=0
3. Execute NCK reset
4. Move axis to reference position after entering MD 34010:
REFP_CAM_DIR_IS_MINUS according to the approach direction.
(If the axis is traversed in the negative direction towards the reference
position, then MD 34010 must be set to 1.)
5. Set MD 34100: REFP_SET_POS to the actual value of the reference
position.
6. Set MD 34210: ENC_REFP_STATE to 1 to start the adjustment.
7. Select the axis that has been compared at the MCP and press the RESET
key on the MCP.
8. Select JOG/REF mode, give feed enabling command for axis.
9. Start the adjustment process with the traversing key “+” or “–” according to
MD 34010: REFP_CAM_DIR_IS_MINUS and the direction of approach to
the reference position. (Backlash has been eliminated.)
The axis does not traverse. Instead, the offset between the correct actual
value (reference position) and the actual value supplied by the encoder is
entered in MD 34090: REFP_MOVE_DIST_CORR. The current actual value
appears in the basic display, the axis signals “referenced”. The value 2 is
entered in MD 34210 as the result.
Example:
MD 34010 = 1 (negative) and reference position has been traversed in negative direction. In this case, the “–” key on the MCP must also be pressed.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-93
03/2006
6 Programming the control
6.9 Axes and spindles
Rotary absolute
encoder with large
traveling range
The encoder EQN 1325 can represent 4096 revolutions. This means that the
detected positional value is unique over the maximum specified ranges:
S Rotary axis, encoder on load: 4096 load revolutions
S Rotary axis, encoder on motor: 4096 motor revolutions
S Linear axis, encoder on motor: 4096 * eff. spindle pitch
For a linear axis with an effective spindle pitch of 10 mm, a traveling range of
40.96 m is covered.
Note
The traveling range is the same as for the incremental encoders.
The user must ensure that, when the encoder is switched off (Power Off/On,
Park), the axis moves less than half of the absolute encoder numerical range
that can be clearly represented.
6
In this case, the software can reconstruct the new position by detecting the
shortest route.
Apart from this, changes of position with an active encoder are possible without
restriction over the entire traveling range.
NCK-RESET
A further NCK reset is required after entering and saving all the drive records.
The SF LED then goes out and the drives can be traversed after PLC start-up
(speed controller preset).
After the axis-specific velocity and travel range limits have been adapted, the
speed control preset values should be optimized.
6-94
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
6.9.7
Overview of the drive parameters
Optimize the drive by means of the following parameters (see also Chapter 10):
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
Table 6-19
Speed controller settings
No.
Identifier
Name
1401
1001
1407
1409
1413
1408
1410
1411
1412
1421
MOTOR_MAX_SPEED[0...7]
SPEEDCTRL_CYCLE_TIME[DRx]
SPEEDCTRL_GAIN_1[0...7,DRx]
SPEEDCTRL_INTEGRATOR_TIME_1[0...7,DRx]
SPEEDCTRL_ADAPT_ENABLE[DRx]
SPEEDCTRL_GAIN_2[0...7,DRx]
SPEEDCTRL_INTEGRATOR_TIME_2[0...7,DRx]
SPEEDCTRL_ADAPT_SPEED_1[DRx]
SPEEDCTRL_ADAPT_SPEED_2[DRx]
SPEEDCTRL_INTEGRATOR_FEEDBK[0...7,DRx]
Setpoint scaling
Speed controller clock cycle
Speed controller P gain
Speed controller reset time
Selection speed controller adaptation
P gain for upper adaptation speed
Reset time upper adaptation speed
Lower adaptation speed
Upper adaptation speed
Time constant integrator feedback
Table 6-20
Drive
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
Field weakening for MSD
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
No.
Identifier
Name
Drive
1142
FIELD_WEAKENING_SPEED[DRx]
Threshold speed field weakening
MSD
Table 6-21
Setpoint current filter
No.
Identifier
Name
1200
1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
NUM_CURRENT_FILTERS[0...7,DRx]
CURRENT_FILTER_CONFIG[0...7,DRx]
CURRENT_FILTER_1_FREQUENCY[0...7,DRx]
CURRENT_FILTER_1_DAMPING[0...7,DRx]
CURRENT_FILTER_2_FREQUENCY[0,..7,DRx]
CURRENT_FILTER_2_DAMPING[0...7,DRx]
CURRENT_FILTER_3_FREQUENCY[0...7,DRx]
CURRENT_FILTER_3_DAMPING[0...7,DRx]
CURRENT_FILTER_4_FREQUENCY[0...7,DRx]
CURRENT_FILTER_4_DAMPING[0...7,DRx]
CURRENT_FILTER_1_SUPPR_FREQ[0...7,DRx]
CURRENT_FILTER_1_BANDWIDTH[0...7,DRx]
CURRENT_FILTER_1_BW_NUM[0...7,DRx]
CURRENT_FILTER_2_SUPPR_FREQ[0...7,DRx]
CURRENT_FILTER_2_BANDWIDTH[0...7,DRx]
CURRENT_FILTER_2_BW_NUM[0...7,DRx]
CURRENT_FILTER_3_SUPPR_FREQ[0...7,DRx]
CURRENT_FILTER_3_BANDWIDTH[0...7,DRx]
CURRENT_FILTER_3_BW_NUM[0...7,DRx]
CURRENT_FILTER_4_SUPPR_FREQ[0...7,DRx]
CURRENT_FILTER_4_BANDWIDTH[0...7,DRx]
CURRENT_FILTER_4_BW_NUM[0...7,DRx]
Select setpoint current filter
Setpoint current filter type
Natural freq. setp. current filter 1
Damping setpoint current filter 1
Natural freq. setp. current filter 2
Damping setpoint current filter 2
Natural freq. setp. current filter 3
Damping setpoint current filter 3
Natural freq. setp. current filter 4
Damping setpoint current filter 4
Blocking freq. setpoint current filter 1
Bandwidth setpoint current filter 1
Numerat. bandw. setp. current filter 1
Blocking freq. setpoint current filter 2
Bandwidth setpoint current filter 2
Numerat. bandw. setp. current filter 2
Blocking freq. setp. current filter 3
Bandwidth setpoint current filter 3
Numerat. bandw. setp. current filter 3
Blocking freq. setpoint current filter 4
Bandwidth setpoint current filter 4
Numerat. bandw. setp. current filter 4
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Drive
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
FDD/MSD
6-95
6
03/2006
6 Programming the control
6.9 Axes and spindles
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
Table 6-22
No.
Identifier
Name
1500
1502
NUM_SPEED_FILTERS[0...7,DRx]
SPEED_FILTER_1_TIME[0...7,DRx]
Number of setpoint speed filters
Time constant setpoint speed filter 1
Drive
FDD/MSD
FDD/MSD
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
Table 6-23
6
Setpoint speed filter
Main monitoring and limiting functions
No.
Identifier
Name
Drive
1145
STALL_TORQUE_REDUCTION[DRx]
Stall torque reduction factor
1230
TORQUE_LIMIT_1[0...7,DRx]
1st torque limit
FDD/MSD
1239
TORQUE_LIMIT_FOR_SETUP[DRx]
Torque limit for set-up mode
FDD/MSD
1235
POWER_LIMIT_1[0...7,DRx]
1st power limit value
FDD/MSD
1237
POWER_LIMIT_GENERATOR[DRx]
Maximum output generator mode
FDD/MSD
1105
MOTOR_MAX_CURRENT_REDUCTION[DRx]
Reduction in max. motor current
FDD
1238
CURRENT_LIMIT[DRx]
Current limit value
MSD
1605
SPEEDCTRL_LIMIT_TIME[DRx]
Timer n controller at limit
FDD/MSD
1606
SPEEDCTRL_LIMIT_THRESHOLD[DRx]
Threshold n controller at limit
FDD/MSD
1405
MOTOR_SPEED_LIMIT[0...7,DRx]
Motor monitoring speed
FDD/MSD
1420
MOTOR_MAX_SPEED_SETUP[DRx]
Max. motor speed set-up mode
FDD/MSD
1147
SPEED_LIMIT[DRx]
Speed limitation
FDD/MSD
MSD
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁ
Table 6-24
Major messages
No.
Identifier
Name
1417
SPEED_THRESHOLD_X[0...7,DRx]
nx for ‘nact<nx’ message
FDD/MSD
1418
SPEED_THRESHOLD_MIN[0...7,DRx]
nmin for ‘nact>nmin’ message
FDD/MSD
1426
SPEED_DES_EQ_ACT_TOL[0...7,DRx]
Toler. band for ‘nset=nact’ message
FDD/MSD
1428
TORQUE_THRESHOLD_X[0...7,DRx]
Threshold torque Mdx
FDD/MSD
1602
MOTOR_TEMP_WARN_LIMIT[DRx]
Motor temp. warning threshold
FDD/MSD
6-96
Drive
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
n_set
+
Function generator
for FFT analysis
PT1:
Speed
setpoint filter: 611D /CCU3: 2x
1500 NUM_SPEED_FILTERS
1502 SPEED_FILTER_1_TIME
611D/CCU3
2nd setpoint speed filter
with low-pass and bandstop filter
611D/CCU3:
Setpoint speed precontrol
Setpoint speed
limitation
1503 SPEED_FILTER_2_TIME
+
1405 MOTOR_SPEED_LIMIT
Actual speed monitoring
nact > MD 1147 SPEED_LIMIT
=> Torque setpoint limitation = 0
Speed control loop
Set-up mode
1420 MOTOR_MAX_SPEED_SETUP+
1409 SPEEDCTRL_INTEGRATOR_TIME_1 Speed controller
1413
1410
1411
1412
reset time
SPEEDCTRL_ADAPT_ENABLE
SPEEDCTRL_INTEGRATOR_TIME_2
SPEEDCTRL_ADAPT_SPEED_1
SPEEDCTRL_ADAPT_SPEED_2
Speed controller
P gain
Integrator feedback
1407
1413
1408
1411
1412
+
1421 SPEEDCTRL_INTEGRATOR_FEEDBK [n]
+
6
SPEEDCTRL_GAIN 1[n]
SPEEDCTRL_ADAPT_ENABLE
SPEEDCTRL_GAIN_2[n]
SPEEDCTRL_ADAPT_SPEED_1
SPEEDCTRL_ADAPT_SPEED_2
+
611D:
Weight balancing/precontrol torque
1725 MAXIMAL_TORQUE_FROM_NC
1230 TORQUE_LIMIT_1
1233 TORQUE_LIMIT_GENERATOR
1235 POWER_LIMIT_1
1237 POWER_LIMIT_GENERATOR
1145 STALL_TORQUE_REDUCTION (MSD)
Torque setpoint limitation
Set-up mode
1239 TORQUE_LIMIT_FOR_SETUP
&
Torque conversion
acc. to cross current
PT2:
1208 CURRENT_FILTER_4_FREQUENCY
1209 CURRENT_FILTER_4_DAMPING
Band-stop filter
1219 CURRENT_FILTER_4_SUPPR_FREQ
1220 CURRENT_FILTER_4_BANDWIDTH
1221 CURRENT_FILTER_4_BW_NUM
Setpoint torque
monitoring
1605 SPEEDCTRL_LIMIT_TIME
n_act <1606 SPEEDCTRL_
LIMIT_THRESHOLD
Filter 4
ALARM: 300608 axis %1, drive %2
speed controller output limited
Setpoint current filter
PT2:
1206 CURRENT_FILTER_3_FREQUENCY
1207 CURRENT_FILTER_3_DAMPING
Band-stop filter
1216 CURRENT_FILTER_3_SUPPR_FREQ
1217 CURRENT_FILTER_3_BANDWIDTH
1218 CURRENT_FILTER_3_BW_NUM
PT2:
1204 CURRENT_FILTER_2_FREQUENCY
1205 CURRENT_FILTER_2_DAMPING
Band-stop filter
1213 CURRENT_FILTER_2_SUPPR_FREQ
1214 CURRENT_FILTER_2_BANDWIDTH
1215 CURRENT_FILTER_2_BW_NUM
1200 NUM_CURRENT_FILTERS
1201 CURRENT_FILTER_CONFIG
Filter 4 3 2 1 0:= Low pass
Filter 3
Bit
3210
1:= Band-stop
611D/CCU3:
Filter 1–4 in current controller
Filter 2
Actual speed filter PT1:
1522 ACT_SPEED_FILTER_TIME
n_act
Fig. 6-13
iq_set
Speed controller with the most important properties
Reference material:
/FBA/
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
DD2, Description of the drive functions,
Speed control loop
6-97
03/2006
6 Programming the control
6.9 Axes and spindles
Note
For monitoring and limitation, see
Reference material
/FBA/ DÜ1, Description of the drive functions,
Monitoring/limiting devices
Note
Changes to the FDD MD or MSD MD will be erased by an NCK reset if “Save
boot file(s)” is not performed beforehand.
6
6-98
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
6.9.8
Axis data
For SINUMERIK 840D, 8 (or 5 for NCU 571) linear axes, which are assigned to
channel 1 (or 2), are active by default. The rotary axis and spindle must be
assigned during start-up.
Distinguishing
between linear
axis and rotary
axis
For a rotary axis, the MD 30300: IS_ROT_AX must be set. This setting causes
the setpoint unit to be switched over from mm to degrees. The display for the
rotary axis is programmed in relation to 360 degrees, MD 30320:
DISPLAY_IS_MODULO (modulo 360 degree display for rotary axes),
MD 30310: ROT_IS_MODULO (modulo conversion for rotary axis).
These MD are activated after power-on. When MD 30300 is set followed by
power-on, the active axis machine data (e.g. for velocity, acceleration, jerk) are
converted automatically to the new physical unit.
Example
Velocity = 10000 mm/min for linear axis MD 30300: IS_ROT_AX=0
After conversion to rotary axis, this MD contains the value 27.77777778 and the
unit is now rev./min.
Axis types
Indexing axis
MD 30500: INDEX_AX_ASSIGN_POS_TAB (indexing axis assignment) must
specify which global list (generally MD 10900:
INDEX_AX_LENGTH_POS_TAB1 or MD 10910: INDEX_AX_POS_TAB1
should be used for list 1 and MD 10920 or MD 10930 for list 2) with indexing
positions.
Concurrent
positioning axis
MD 30450: IS_CONCURRENT_POS_AX is used to define the axis as a
“Concurrent positioning axis”.
Reference material:
/FB2/ P2, Description of the advanced functions,
Positioning axes
Parameter sets
For machine data with the field parameter “Controller parameter set no.”, the
first field is used for normal axis operation. For interpolation involving a spindle,
e.g. for G331 (tapping without compensating chuck), the selected gear
determines the corresponding field of the axes involved (1st gear –––> field
index 1). This applies to all machine axes which can be traversed via geometry
axes. See Section 6.9.2.
Axis
For axes that interpolate together with a spindle during thread cutting (G33,
G34, G35, G331, G332), the machine data must also be supplied with corresponding values with the indices [1]...[5].
Spindle
All existing gear steps must be parameterized for rotary axes that are to be operated as a spindle with gear step change. (Indices [1]...[5].)
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-99
6
03/2006
6 Programming the control
6.9 Axes and spindles
Parameter set
Axis
Spindle
Spindle gear step
Standard
Spindle in
axis mode
As specified by
manufacturer
1
Axis interpolates
with spindle (G33)
Spindle mode
1st
2
Axis interpolates
with spindle (G33)
Spindle mode
2nd
3
Axis interpolates
with spindle (G33)
Spindle mode
3rd
4
Axis interpolates
with spindle (G33)
Spindle mode
4th
5
Axis interpolates
with spindle (G33)
Spindle mode
5th
0
6
Fig. 6-14
Validity of parameter sets in axis and spindle modes
MD 31050: DRIVE_AX_RATIO_DENOM (denominator for load gearbox)
MD 31060: DRIVE_AX_RATIO_NUMERA (numerator for load gearbox)
MD 32200: POSCTRL_GAIN (KV factor)
MD 32800: EQUIV_CURRCTRL_TIME (equivalent time constant of current
control circuit for bias control)
MD 32810: EQUIV_SPEEDCTRL_TIME (equivalent time constant for speed
control circuit for bias control)
MD 32910: DYN_MATCH_TIME (time constant for dynamic matching)
MD 36200: AX_VELO_LIMIT (threshold for velocity monitoring)
Note
The following machine data must be entered consistently. This applies across
all axes if one encoder was activated for several axes (function has not been
released):
MD 31050: DRIVE_AX_RATIO_DENOM
MD 31060: DRIVE_AX_RATIO_NUMERA
MD 32000: MAX_AX_VELO
MD 35100: SPIND_VELO_LIMIT
MD 35110 – 35140: GEAR_STEP_ ...
MD 36200: AX_VELO_LIMIT
MD 36300: ENC_FREQ_LIMIT
Example
MD 32200: POSCTRL_GAIN [0,Z1] = 1 (KV for normal axis operation)
MD 32200: POSCTRL_GAIN [1,Z1] = 1 (KV for G331, spindle gear step 1)
MD 32200: POSCTRL_GAIN [3,Z1] = 1 (KV for G331, spindle gear step 3)
MD 32200: POSCTRL_GAIN [0,X1] = 1 (KV for normal axis operation)
MD 32200: POSCTRL_GAIN [1,X1] = 1 (KV for G331, spindle gear step 1)
MD 32200: POSCTRL_GAIN [3,X1] = 1 (KV for G331, spindle gear step 3)
6-100
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
Note
In order to ensure reliable power-up of the control, all activated axes are declared as simulation axes (without hardware) during initialization.
MD 30130: CTRLOUT_TYPE = 0
MD 30240: ENC_TYPE = 0
The control loop is simulated while traversing the axes, and no hardware-specific alarms are output. For starting up an axis or spindle, the value “1” or the
corresponding value of the hardware identifier should be entered in this MD.
MD 30350: SIMU_AX_VDI_OUTPUT can be used to select whether the interface signals of a simulated axis should be output at the PLC interface (e.g. for
testing programs when there is no drive hardware present).
Interface signals
for measuring
system changeover
Interface signals are used to select the active measuring system for the position
control.
NST “Position measuring system 1 selected” (DB31, ... DBX1.5)
NST “Position measuring system 2 selected” (DB31, ... DBX1.6)
If both signals are set, then position measuring system 1 was selected.
Reference material: /FB1/ A2, Functional description of the basic machines,
Various NC/PLC interface signals and functions
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-101
6
03/2006
6 Programming the control
6.9 Axes and spindles
6.9.9
Axis velocity matching
Machine data for
velocity matching
The following machine data must be defined:
MD 32000: MAX_AX_VELO (maximum axis velocity)
MD 32010: JOG_VELO_RAPID (conventional rapid feed)
MD 32020: JOG_VELO (conventional axis velocity)
MD 34020: REFP_VELO_SEARCH_CAM (reference point approach
velocity)
MD 34040: REFP_VELO_SEARCH_MARKER [n] (cut-out velocity)
MD 34070: REFP_VELO_POS (reference point move-in velocity)
Note
When new velocities are entered, the velocity monitoring (MD 36200:
AX_VELO_LIMIT) must also be matched.
6
For axis drives, the motor speed at which the velocity MAX_AX_VELO
(MD 32000) is achieved must be set in MD 1401.
For the setpoint scaling, the load gearbox must always be entered correctly.
MD 31060: DRIVE_AX_RATIO_NUMERA (number of motor revolutions)
MD 31050: DRIVE_AX_RATIO_DENOM (number of load revolutions)
6-102
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
6.9.10
Axis position control data
Control loops
The controller for an axis consists of the speed control loop, the current control
loop and a higher-level position control loop.
nset
Position setpoint
from
interpolator
Position
controller
Actual position
value
(position)
Fig. 6-15
iset
Speed
controller
Current
controller
Motor
Encoder
iact
nact
6
Control loops
Traversing
direction
If the axis does not move in the desired direction, it is adapted via MD 32100:
AX_MOTION_DIR (traversing direction). The value “–1” reverses the direction
of motion. Allowance is made internally for the control direction of the position
controller. If the control direction of the position measuring system is the wrong
way around, this is corrected with MD 32110: ENC_FEEDBACK_POL (actual
sign value).
Loop gain
In order to obtain high contour accuracy with an interpolation, the loop gain
factor (KV factor) of the position controller must be large. If the KV factor is too
high, on the other hand, this leads to overshooting, instability and inadmissibly
high loading of the machine. The maximum permissible KV factor is dependent
on the design and dynamic response of the drive and the mechanical quality of
the machine.
Definition of the KV
(loop gain) factor
KV =
Velocity
[m/min]
Following error
[mm]
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-103
03/2006
6 Programming the control
6.9 Axes and spindles
Automatic scaling
For the KV factor 1 (m/min)/mm numerical value 1 must be entered in
MD 32200: POSCTRL_GAIN.
The correct scaling of the Kv factor is automatically activated by the following
machine data.
MD 10220: SCALING_USER_DEF_MASK
The correct physical size is taken into account by the following machine data:
MD 10230: SCALING_FACTORS_USER_DEF .
The loop gain is converted using the following formula:
KV (s–1)= KV *
6
Checking the
loop gain
[m/min]
* 16.66667
[mm]
If a KV factor is already known for the machine type, it can be set and checked.
For the check, the acceleration of the axis is reduced via MD 32300:
MAX_AX_ACCEL to ensure that the drive does not reach its current limit while
accelerating and braking.
In the case of rotary axes and spindles, the KV factor must also be checked at
high speeds (e.g. for spindle positioning, tapping).
The loop gain should always be checked.
If it is not correct, the right Kv factor, e.g. the factor 16.667 is entered in
MD 32200 POSCTRL_GAIN.
The static check of the KV factor is done using the “Service axis” soft key from
the “Service display” menu. The actual KV factor must correspond exactly to the
set value, as the KV factor is used for monitoring functions and otherwise other
responses may be caused (e.g. contour monitoring).
For continuous-path operation, all the axes involved in the interpolation must
have the same dynamic behavior.
Note
Axes which interpolate with one another must have the same following error at
the same velocities. This can be achieved by setting the same KV factor or by
dynamic matching via the following machine data:
MD 32900: DYN_MATCH_ENABLE (dynamic matching) and
MD 32910: DYN_MATCH_TIME (time constant for dynamic matching)
Reference material: /FB1/ G2, Functional description of the basic machines,
Velocities, setpoint/actual value systems, control
6-104
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
Checking the positioning response
A storage oscilloscope or the start-up software SIMODRIVE 611D/
start-up/drives/servo/servo trace is used to check the positioning response at
different velocities. The speed setpoint is recorded for this purpose.
nsetpt.
[V]
nsetpt.
[V]
”bad”
”good”
selected Kv factor
selected Kv factor
t [ms]
Fig. 6-16
t [ms]
Speed setpoint curve
No overshoots may occur while the drive is approaching the static states; this
applies to all speed ranges.
The start-up software SIMODRIVE 611D provides additional options for
checking the KV factor (e.g. frequency response measurement, scanning the
speed and position control loops).
Reasons for overshooting in the position control loop
S KV factor is set too high
S Acceleration too high (current limit is reached)
S Rise time too long (re-optimization necessary)
S Mechanical backlash
S Mechanical components canted
For reasons of safety, the KV factor should be set slightly lower than the
maximum permissible value.
Acceleration
The axes are accelerated and braked with the acceleration specified in
MD 32300: MAX_AX_ACCEL. This value should allow the axes to be
accelerated and positioned rapidly and accurately while ensuring that the
machine is not unduly loaded. The acceleration default settings are in the
0.5 m/s2 to 2 m/s2 range.
Checking and
calculating
acceleration
values
The acceleration data entered can be either empirical values or the maximum
permissible acceleration values which the user must calculate. The data must
always be checked after entry for which the SIMODRIVE 611D start-up software
and an oscilloscope are required.
Setting
MD 32300: MAX_AX_ACCEL
Identification
Overshoot-free acceleration and positioning with rapid traverse velocity under
maximum load (heavy workpiece).
Measurement
Via analog outputs (section 10) or start-up software for SIMODRIVE 611D.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-105
6
03/2006
6 Programming the control
6.9 Axes and spindles
After the acceleration has been entered, the axis is traversed rapidly and the
actual current values and current setpoint are recorded. This recording shows
whether the drive reaches the current limit. While traversing rapidly, the drive
may reach the current limit briefly. However, the current must be well below the
current limit before rapid traverse velocity or the final position is reached.
Load changes during machining must not cause the current limit to be reached.
Excessive current during machining causes falsification of the contour. It is therefore advisable in this case as well to enter a slightly lower acceleration value
in the MD than the maximum permissible value. Axes can be assigned different
acceleration values even if they do interpolate with one another.
MD32400 AX_JERK_ENABLE
MD32402 AX_JERK_MODE
MD32410 AX_JERK_TIME
6
Fine
interpolation
MD33000
FIPO_TYPE
Jerk
limitation
MD32200 POSCTRL_GAIN[n]
Dynamic
response
matching
Feedforward
control
MD32900 DYN_MATCH_ENABLE
MD32910 DYN_MATCH_TIME[n]
Regulation
Speed
setpoint
processing
MD32500 FRICT_COMP_ENABLE*
MD32100 AX_MOTION_DIR
NST
position measuring
system 1/2
MD32620
MD32630
MD32610
MD32650
MD32810
MD32800
Fig. 6-17
FFW_MODE
FFW_ACTIVATION_MODE
VELO_FFW_WEIGHT[n] from SW vers. 5.1 parameter sets MD32110 ENC_FEEDBACK_POL[n]
AX_INERTIA
MD32700 ENC_COMP_ENABLE[n]
EQUIV_SPEEDCTRL_TIME[n]
MD32450 BACKLASH[n]
MD32452 BACKLASH_FACTOR[n]
EQUIV_CURRCTRL_TIME[n]
Actual
value
processing
Additional parameters for position control
*Further machine data for friction compensation FRICT... can be found in:
Reference material: /FB2/ K3, Description of the advanced functions,
Compensation
Optimizing the control
Control of an axis can be optimized as follows with respect to the speed control
loop, current control loop and the higher-level position control loop:
Positional
deviation
feedforward
6-106
The positional deviation feedforward takes place on the NCK side within the
position control cycle and is designed to improve the stability and positioning
response of axes with at least two encoders (load and motor encoder) by
actively damping oscillations.
S The function is activated with MD 32950: POSCTRL_DAMPING ,0 and is
available for all controls that use SIMODRIVE_611 D drives.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
Bias control
If bias control is active for speed and torque, the position setpoint is routed via a
new balance filter before it reaches the actual controller in order to improve the
oscillatory response of the axis. It also achieves greater accuracy at curved
contours.
S The speed bias control is activated with MD 32620: FFW_MODE = 3.
S The torque bias control is activated with MD 32620: FFW_MODE = 4.
The MD 32620: FFW_MODE = 1 and = 2 settings remain available and behave
as before. The response of the axis can be improved with the new settings for
MD 32620 = 3 and MD 32620 = 4.
New jerk filter
(position setpoint
filter)
Smoothing the position setpoint can help to reduce machine oscillations. A new
type of filter for filter time constants of approx. 20–40ms achieves largely
symmetrical smoothing by averaging while giving little consideration to the
contour accuracy.
S The new jerk filter is activated with MD 32402: AX_JERK_MODE = 2.
For reasons of compatibility, MD 32402: AX_JERK_MODE = 1 by default. On
new machines, the new filter MD 32402: = 2 is generally recommended.
Extending the
parameter set
From software version 5.1, the following parameter sets are also available for
backlash compensation, bias control factor, exact positioning limits and
zero-speed tolerance.
MD 32450: BACKLASH (backlash compensation)
MD 32610: VELO_FFW_WEIGHT (bias control factor)
MD 36000: STOP_LIMIT_COARSE (coarse exact stop)
MD 36010: STOP_LIMIT_FINE (fine exact stop)
MD 36030: STANDSTILL_POS_TOL (zero-speed tolerance)
Weighting factor
The following machine data with suitable weighting factors is available for the
parameter set-specific machine data mentioned above.
MD 32452: BACKLASH_FACTOR[n] (backlash compensation) affects:
S MD 32450: BACKLASH (backlash compensation)
MD 36012: STOP_LIMIT_FACTOR[n] (exact stop limit and zero-speed
tolerance) affects:
S MD 36000: STOP_LIMIT_COARSE (coarse exact stop)
MD 36010: STOP_LIMIT_FINE (fine exact stop)
MD 36030: STANDSTILL_POS_TOL (zero-speed tolerance)
The machine data MD 32452: BACKLASH_FACTOR[n] and MD 36012:
STOP_LIMIT_FACTOR[n] are set to the weighting factor [n] = 1 by default.
Example
Effects of various parameter sets on backlash compensation
MD 32450: BACKLASH[AX1] = 0.01
MD 32452: BACKLASH_FACTOR[0,AX1] = 1.0
MD 32452: BACKLASH_FACTOR[1,AX1] = 2.0
Parameter set 1
Parameter set 2
In parameter set 1 (index 0) for the first axis (AX1), a backlash compensation
factor with the value 1.0 has the following effect:
1.0 * MD 32450: BACKLASH = 0.01 mm (or inch or degree)
2.0 * MD 32450: BACKLASH = 0.02 mm (or inch or degree).
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-107
6
03/2006
6 Programming the control
6.9 Axes and spindles
6.9.11
Monitoring for axis
Reference material: /FB1/ Functional description of the basic machines
/A3/ Axis monitoring, protected areas
/B1/ Continuous-path operation, exact stop and
LookAhead
/G2/ Velocities, setpoint/actual value systems, control
6
Monitoring the
positioning
For positioning, the monitoring ensures that the axis reaches the position
window (exact stop). It also checks whether an axis for which no traversing
command has been issued remains within a certain tolerance window (zero
speed control, clamping tolerance).
MD 36000
STOP_LIMIT_COARSE (coarse exact stop)
S IS “Position reached with coarse exact stop” (DB31, ... DBX60.6)
MD 36010
STOP_LIMIT_FINE (fine exact stop)
S IS “Position reached with fine exact stop” (DB31, ... DBX60.7)
MD 36012
STOP_LIMIT_FACTOR[n] (factor for parameter set-independent evaluation of
the exact stop (coarse or fine) and zero-speed monitoring)
S The ration between the three following values remains the same at all times:
MD 36000: STOP_LIMIT_COARSE
MD 36010: STOP_LIMIT_FINE
MD 36030: STANDSTILL_POS_TOL
MD 36020
POSITIONING_TIME (fine exact stop delay)
S The MD represents the delay time after which the actual value must have
reached the “exact stop fine” tolerance window when the setpoint position at
the block end is attained.
S If the value does not reach the exact stop fine window within this time, the
“25080 axis [name] positioning monitoring” alarm is generated.
The control switches to follow-up mode.
MD 36030
STANDSTILL_POS_TOL (zero-speed tolerance)
S The machine data specifies the position tolerance which a standing axis
must adhere to.
S If the axis leaves the position tolerance window, the “25040 axis [name]
zero-speed control” alarm is output. The control switches to follow-up mode.
MD 36040
STANDSTILL_DELAY_TIME (delay time zero-speed control)
S The MD represents the delay after which the actual value must have
S
reached the “zero-speed tolerance” window when the setpoint position at
the block end is attained.
If the position tolerance is not reached within this time, the “25040 axis
[name] zero-speed control” alarm is generated.
The control switches to follow-up mode.
MD 36050
CLAMP_POS_TOL (clamping tolerance)
S Position tolerance while the “clamping active” signal is present at the PLC
S
6-108
interface. When the tolerance is exceeded, the alarm “26000 axis [name]
clamping monitoring” is generated.
IS “clamping active” (DB31, ... DBX2.3)
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
V or S
Actual
Interface signal
“clamping active”
CLAMP_POS_TOL
Setpoint
STANDSTILL_POS_TOL
STOP_LIMIT_COARSE
STOP_LIMIT_FINE
Exact stop fine signal
Time t
Exact stop course signal
STANDSTILL_
DELAY_TIME
POSITIONING_TIME
Fig. 6-18
Positioning, zero-speed and clamping monitoring
Monitoring of positions via Hardware
limit switch
For each axis, it is possible to carry out the monitoring via the PLC interface.
A signal exists for every traversing range limit informing the NC that the
corresponding traversing range limit has been approached. When the limit
switch is reached, the axis or the axes used for interpolation are stopped.
Braking can be set via MD 36600: BRAKE_MODE_CHOICE (braking response
with hardware limit switches).
Machine data,
interface signals and
alarms
MD 36600: BRAKE_MODE_CHOICE = 1 (fast braking with setpoint “0”)
MD 36600: BRAKE_MODE_CHOICE = 0 (braking characteristic is maintained)
NST “Hardware limit switch minus” (DB31, ... DBX12.0)
NST “Hardware limit switch plus” (DB31, ... DBX12.1)
Alarm “21614 channel [name1] axis [name2] hardware limit switch [+/–]”. The
axis must be retracted in JOG operating mode.
Monitoring of positions via software
limit switches
Two software limit switch values may be entered in the machine data for each
axis. The active software limit switch is selected via the PLC. The axis does not
traverse beyond the software limit switch. The monitoring function is activated
after reference point approach and is deactivated after PRESET.
Machine data,
interface signals and
alarms
MD 36100: POS_LIMIT_MINUS
MD 36110: POS_LIMIT_PLUS
MD 36120: POS_LIMIT_MINUS2
MD 36130: POS_LIMIT_PLUS2
(1st software limit switch minus)
(1st software limit switch plus)
(2nd software limit switch minus)
(2nd software limit switch plus)
NST “2nd software limit switch minus”
NST “2nd software limit switch plus”
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
(DB31, ... DBX12.2)
(DB31, ... DBX12.3)
6-109
6
03/2006
6 Programming the control
6.9 Axes and spindles
6
Machine data,
interface signals and
alarms
MD 36100: POS_LIMIT_MINUS (1st software limit switch minus)
MD 36110: POS_LIMIT_PLUS (1st software limit switch plus)
MD 36120: POS_LIMIT_MINUS2 (2nd software limit switch minus)
MD 36130: POS_LIMIT_PLUS2 (2nd software limit switch plus)
NST “2nd software limit switch minus” (DB31, ... DBX12.2)
NST “2nd software limit switch plus” (DB31, ... DBX12.3)
Alarm “10620 channel [name1] set [no.] axis [Name2] reaches software limit
switch +/–”
Alarm “10621 channel [name1] axis [name2] is at software limit switch +/–
(JOG)”
Alarm “10720 channel [name1] set [no.] axis [name2] programmed limit is after
software limit switch +/–”
Monitoring of
positions via work
area limits
With geometry axes, the setting data or part program (with G25/G26) can be
used to set and activate work area limits. These are is activated via setting data
or from the program. The monitoring is active after machine referencing.
Setting data and
alarms
SD 43400: WORKAREA_PLUS_ENABLE (work area limits active in the positive
direction)
SD 43410: WORKAREA_MINUS_ENABLE (work area limits active in the
negative direction)
SD 43420: WORKAREA_LIMIT_PLUS (work area limit plus)
SD 43430: WORKAREA_LIMIT_MINUS (work area limit minus)
Alarm “10630 channel [name1] set [no.] axis [Name2] reaches work area limit
+/–”
Alarm “10631 channel [name1] axis [name2] is at work area limit +/– (JOG)”
Alarm “10730 channel [name1] set [no.] axis [name2] programmed limit is after
work area limit +/–”
Working area
limitation
(for geometry
axes only)
1st software
EMERGENCY
limit switch
STOP
2nd software
HW limit
Mechanical
limit switch
switch
traversing limit
(can be activated via PLC)
Fig. 6-19
6-110
Overview of end limitations
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
Dynamic
monitoring
functions
Velocity limitation
The velocity matching takes place inside the SINUMERIK 840D. The setpoint is
limited as a percentage via MD 36210: CTRLOUT_LIMIT in relation to the
speed entered in MD 1401: MOTOR_MAX_SPEED. An alarm is generated if
the setpoint is exceeded for the set time MD 36220: CTRLOUT_LIMIT_TIME.
The axes are stopped with the open position control loop via a braking ramp,
MD 36610: AX_EMERGENCY_STOP_TIME. This MD must contain the time
within which the axis can brake to zero from maximum velocity.
MD 36210: CTRLOUT_LIMIT (maximum speed setpoint)
MD 36220: CTRLOUT_LIMIT_TIME (monitoring time for maximum speed
setpoint)
MD 36610: AX_EMERGENCY_STOP_TIME (duration of the braking ramp in
error states)
Alarm “25060 axis [name] speed setpoint limitation”
Velocity monitoring
The monitoring is intended to ensure that axes whose theoretical velocity is
limited by mechanical conditions (e.g. by the mechanical limit frequency of the
pulse encoder) run without error. The actual velocity monitoring is always active
if at least one encoder is configured on the axis (MD 30200 NUM_ENCS < > 0)
and this is below its limit frequency. Alarm 25030 is output if the threshold is
exceeded.
MD 36020: AX_VELO_LIMIT (threshold for velocity monitoring)
MD 36610: AX_EMERGENCY_STOP_TIME (duration of the braking ramp in
error states)
Alarm “25030 axis [name] actual velocity alarm limit”
Contour monitoring
This monitoring is based on an ongoing comparison of the measured following
error and the error calculated in advance from the NCK position setpoint.
Contour monitoring is always active in position-controlled mode. If the tolerance
band is violated, then the alarm “Contour monitoring” is generated and the axes
are braked along a set braking ramp.
MD 36400: CONTOUR_TOL (contour monitoring tolerance band)
MD 36610: AX_EMERGENCY_STOP_TIME (duration of the braking ramp in
error states)
Alarm “25050 axis [name] contour monitoring”.
Encoder monitoring
(encoder limit frequency monitoring)
The frequency entered in MD: ENC_FREQ_LIMIT is monitored. If this is
exceeded, the alarm “Encoder frequency exceeded” is output and the axes
braked to zero speed. The interface signal “Referenced/synchronized” is reset
(DB31, ... DBX60.4, DBX60.5).
Example:
Encoder with 2048 pulses directly on the motor, limit frequency 200 kHz,
nmax = (flimit/pulses) * 60 sec= 5900 1/min
Result:
It must be ensured that this speed is not reached at maximum axis velocity
(MAX_AX_VELO).
MD 36300: ENC_FREQ_LIMIT (encoder limit frequency),
NST “Encoder limit frequency exceeded 1” (DB31, ... DBX60.2),
NST “Encoder limit frequency exceeded 2” (DB31, ... DBX60.3),
Alarm “21610 channel [name] axis [name] Encoder frequency exceeded”.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-111
6
03/2006
6 Programming the control
6.9 Axes and spindles
Encoder monitoring
(zero marker
monitoring)
MD 36310: ENC_ZERO_MONITORING > 0 activates the zero marker
monitoring. The value indicates the number of pulses that may be lost.
Special feature:
Value = 100, i.e. the hardware monitoring for the encoder is also switched off.
MD 36310: ENC_ZERO_MONITORING (zero marker monitoring)
MD 36610: AX_EMERGENCY_STOP_TIME (duration of the braking ramp in
error states)
Alarm “25020 axis [name] zero marker monitoring”.
Encoder monitoring
(tolerance for encoder switchover)
It is possible to define two actual value branches with SINUMERIK 840D. These
actual values must then, however, be present in the hardware. The actual value
branch which is active for the position control can then be selected via the PLC
interface. When this switchover takes place, the actual position value difference
is evaluated. If this difference is greater than the value entered in MD
36500: ENC_CHANGE_TOL, then “Measuring system changeover not
possible” alarm is generated and the changeover is prevented.
6
MD 36500 ENC_CHANGE_TOL (max. tolerance for actual position
changeover)
NST “Position measuring system 1” (DB31, ... DBX1.5)
NST “Position measuring system 2” (DB31, ... DBX1.6),
Alarm “25100 axis %1 Measuring system changeover not possible”.
MD 36610: AX_EMERGENCY_STOP_TIME
Setpoints
Setpoint
processing
Interpolator
Braking
ramp
Pos.
controller
Drive
SIMODRIVE
611D
Speed
setpoint
MD 36210: CTRLOUT_LIMIT
MD 36400:
CONTOUR_TOL
Control
loop
model
MD 36220: CTRLOUT_LIMIT_TIME
MD 36310: ENC_ZERO_MONITORING
MD 36500: ENC_CHANGE_TOL
MD 36300: ENC_FREQ_LIMIT
MD 36060:
STSTILL_VELO_TOL
Following error
MD 36000: STOP_LIMIT_COURSE
MD 36010: STOP_LIMIT_FINE
MD 36020: POSITIONING_TIME
MD 36030: STANDSTILL_POS_TO
MD 36040: STANDSTILLL_DELAY_TIME
MD 36050: CLAMP_POS_TOL
Fig. 6-20
MD 36200:
AX_VELO_LIMIT
Actual value
processing
Drive
SIMODRIVE
611D
Actual value
processing
IS “Position measuring system 1/2 active”
Monitoring with SINUMERIK 840D
Note
The time set in MD 36620: SERVO_DISABLE_DELAY_TIME (cut-out delay for
controller enable) should always be larger than the time set in MD 36610:
AX_EMERGENCY_STOP_TIME (duration of the braking ramp for error states).
If this is not the case, the braking ramp in MD 36610 cannot take effect.
6-112
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
6.9.12
Referencing an axis
Once the control has been switched on, it must be synchronized (referenced)
with the position measuring system of each machine axis.
Referencing must be carried out for axes with incremental measuring systems
and with distance-coded reference marks.
Referencing is started after selection of the “REF” function with traversing key
PLUS or MINUS (depending on reference point approach direction).
Reference material:
/FB1/ R1 Functional description of the basic machines,
Referencing
General machine
data and interface
signals
MD 34000: REFP_CAM_IS_ACTIVE (axis with reference cam)
MD 34110: REFP_CYCLE_NR (order of the axes for channel-specific
referencing)
MD 30240: ENC_TYPE (encoder type)
MD 34200: ENC_REFP_MODE (referencing mode)
NST “Activate referencing” (DB21, ... DBX1.0)
NST “Referencing active” (DB21, ... DBX33.0)
Referencing for
incremental
measuring
systems
Referencing for incremental measuring systems is divided into 3 phases:
Phase 1:
Move onto reference cam
Phase 2:
Synchronize with zero marker
Phase 3:
Move to reference point
Machine data and
interface signals for
phase 1
MD 11300: JOG_INC_MODE_LEVELTRIGGRD (INC/REF in Jog mode)
MD 34010: REFP_CAM_DIR_IS_MINUS (approach reference cam in minus
direction)
MD 34020: REFP_VELO_SEARCH_CAM (reference cam approachvelocity)
MD 34030: REFP_MAX_CAM_DIST (maximum distance from reference cam)
NST “Traverse buttons plus/minus” (DB31, ... DBX4.7/DBX4.6)
NST “Referencing delay” (DB31, ... DBX12.7)
Machine data for
phase 2
MD 34040: REFP_VELO_SEARCH_MARKER (cut-out velocity)
MD 34050: REFP_SEARCH_MARKER_REVERSE (change of direction at
reference cam)
MD 34060: REFP_MAX_MARKER_DIST (maximum distance from cam to
reference marker)
Machine data and
interface signals for
phase 3
MD 34070: REFP_VELO_POS (reference point move-in velocity)
MD 34080: REFP_MOVE_DIST (distance from reference point to zero marker)
MD 34090: REFP_MOVE_DIST_CORR (reference point move, additive)
MD 34100: REFP_SET_POS (reference point value)
NST “Reference point value 1...4” (DB31, ... DBX2.4, 2.5, 2.6, 2.7)
NST “Referenced/synchronized” 1, 2” (DB31, ... DBX60.4, DBX60.5)
Actual value buffering via Power Off
It is possible to continue to operate a conventional machine tool, for example,
with the original position information without explicitly rereferencing after Power
Off/On.
6
To ensure that axes can continue operating properly referenced after the power
has been switched off and on again, it is essential that they are not moved while
the power is switched off.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-113
03/2006
6 Programming the control
6.9 Axes and spindles
When the encoder is switched on, NCK then synchronizes with an internally
buffered old absolute value (condition: MD 34210: ENC_REFP_STATE=2).
Axis motions are internally disabled until this synchronization process is terminated; spindle operation can continue.
Note
This functionality is permanently linked to the axis signal “Exact stop fine”.
Axes or spindles not using this signal cannot use this functionality.
6
Referencing with
distance-coded
reference markers
Referencing with axes with distance-coded reference markers is divided into
2 phases:
Phase 1:
Synchronize by traveling over 2 reference markers
Phase 2:
Move to target
General machine
data
MD 34310: ENC_MARKER_INC (distance between two reference markers)
MD 34320: ENC_INVERS (measuring system in opposite direction)
Machine data and
interface signals for
phase 1
MD 11300: JOG_INC_MODE_LEVELTRIGGRD (INC and REF in Jog mode)
MD 34040: REFP_VELO_SEARCH_MARKER (referencing velocity)
MD 34060: REFP_MAX_MARKER_DIST (maximum distance between 2 reference markers)
MD 34300: ENC_REFP_MARKER_DIST (distance from reference marker)
NST “Traverse buttons plus/minus” (DB31, ... DBX4.7/DBX4.6)
NST “Referenced/synchronized 1, 2” (DB31, ... DBX60.4, DBX60.5)
Machine data and
interface signals for
phase 2
MD 34070: REFP_VELO_POS (target move-in velocity)
MD 34090: REFP_MOVE_DIST_CORR (absolute move)
MD 34330: REFP_STOP_AT_ABS_MARKER (with/without target)
NST “Referenced/synchronized 1, 2” (DB31, ... DBX60.4, DBX60.5)
MD 34100: REFP_SET_POS (target) if referencing on target.
Referencing with
absolute encoders
If an axis uses an absolute encoder as its measuring system, then it only needs
to be referenced when the encoder is readjusted.
Note
For absolute encoder, see subsection 6.9.6.
6-114
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
6.9.13
Spindle data
In the SINUMERIK 840D control system, the spindle is a sub-function of the
entire axial functionality. The machine data for the spindle are therefore located
among the axis machine data (from MD 35000 onwards). For this reason, data
must be entered for a spindle which are described in the Sections relating to
axis start-up. The following description contains merely a cross-reference to
this MD.
Note
No spindle is defined after a NCK general reset.
Reference material: /FB1/ S1, Functional description of the basic machines,
Spindles
Spindle definition
The following machine data is needed for a spindle definition.
S MD 30300: IS_ROT_AX (rotary axis)
S MD 30310: ROT_IS_MODULO (rotary axis with modulo programming)
S MD 30320: DISPLAY_IS_MODULO (display in relation to 360 degrees,
if required)
S MD 35000: SPIND_ASSIGN_TO_MACHAX (declaration of the axis as a
spindle). Input of the spindle number, with which the spindle is to be
addressed, e.g. “1” means spindle name “S1”.
Spindle modes
The spindle operating modes are as follows:
S Open-loop control mode (M3, M4, M5)
S Oscillation mode (support for gear changing operations)
S Positioning mode (SPOS, M19 and SPOSA)
S Synchronous mode
S Rigid tapping
In spindle mode, the feedforward control switches on as standard (FFW mode =
1). Exception: If tapping without a compensating chuck, the bias control only
takes effect if it is explicitly activated (e.g. via the FFWON programming command).
The set of parameters is selected that corresponds to the current gear step.
Example:
2nd gear step ! parameter set [2]
Axis mode
It is possible to switch directly from spindle mode into axis mode provided that
the same drive is used for both modes. The machine data for one axis must be
applied in axis operation. In axis mode, the first parameter set (index [0]) is
selected irrespective of the current gear step.
After the spindle has been positioned, the rotary axis can be programmed
directly with the axis name.
NST “axis/spindle” (DB31, ... DBX60.0 = 0).
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-115
6
03/2006
6 Programming the control
6.9 Axes and spindles
General machine
data definitions
MD 20090: SPIND_DEF_MASTER_SPIND (reset position for master spindle on
channel )
MD 35020: SPIND_DEFAULT_MODE (default spindle position)
The MD can be used to define a default spindle position.
The following are possible:
S Speed servo control without/with position servo control
S Positioning mode
S Axis mode
The time at which the default spindle position takes effect is defined in
MD 35030: SPIND_DEFAULT_ACT_MASK.
The following are possible:
6
S Power-on
S Power-on and program start
S Power-on, program start and reset
MD 35040: SPIND_ACTIVE_AFTER_RESET (own spindle RESET)
The MD defines whether it is a RESET or a program end that should stop the
spindle. If the MD has been set, a termination of the spindle functions must be
initiated explicitly via a program command or the IS “Spindle reset” (DB31, ...
DBX2.2).
MD 35010: GEAR_STEP_CHANGE_ENABLE (gear step change possible.
Spindle has several gear steps).
If this machine data is not set, the system assumes that the spindle has no gear
steps. A gear step change is therefore impossible.
Parameter sets
In the following machine data with the field parameters “Gear step no.” and
“Control parameter set no.”, the selected gear step determines the
corresponding field index. The field with the index [0] is not used for the spindle
machine data! (See above in the “Axis data” section).
MD 31050: DRIVE_AX_RATIO_DENOM
MD 31060: DRIVE_AX_RATIO_NUMERA
MD 32200: POSCTRL_GAIN
MD 32810: EQUIV_SPEEDCTRL_TIME[n]
MD 32910: DYN_MATCH_TIME[n]
MD 32452: BACKLASH_FACTOR
(denominator for load gearbox)
(numerator for load gearbox)
(KV factor)
(equivalent time constant of
speed control loop for
bias control)
(time constant for dynamic
matching)
(weighting factor for
backlash)
MD 35110: GEAR_STEP_MAX_VELO
(nmax for gear step change)
MD 35120: GEAR_STEP_MIN_VELO
(nmin for gear step change)
MD 35130: GEAR_STEP_MAX_VELO_LIMIT (nmax for gear step)
MD 35140: GEAR_STEP_MIN_VELO_LIMIT (nmin for gear step)
MD 35200: GEAR_STEP_SPEEDCTRL_ACCEL (acceleration in
speed control mode)
MD 35210: GEAR_STEP_POSCTRL_ACCEL (acceleration in
position control mode)
MD 36200: AX_VELO_LIMIT (threshold for velocity monitoring)
6-116
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
Example
6.9.14
MD 35110: GEAR_STEP_MAX_VELO [0,A1] = 500 (not used for spindle)
MD 35110: GEAR_STEP_MAX_VELO [1,A1] = 500
(nmax for gear step change, gear step 1)
MD 35110: GEAR_STEP_MAX_VELO [2,A1] = 1000
(nmax for gear step change, gear step 2)
Spindle configuration
Machine data for
setpoint and actual
values
Setpoints:
MD 30100: CTRLOUT_SEGMENT_NR
MD 30110: CTRLOUT_MODULE_NR
MD 30120: CTRLOUT_NR
MD 30130: CTROUT_TYPE
Actual values
MD 30210: ENC_SEGMENT_NR
MD 30220: ENC_MODULE_NR
MD 30230: ENC_INPUT_NR
MD 30240: ENC_TYPE
6
Note
Further information about the spindle configuration can be found in the “Drive
configuration” section above.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-117
03/2006
6 Programming the control
6.9 Axes and spindles
6.9.15
Spindle encoder matching
Encoder matching
via machine data
The machine data for matching the spindle encoder is the same as for the axis.
For spindles, it is always MD 30300: IS_ROT_AX and MD 30310:
ROT_IS_MODULO that should be set so that the encoder matching relates to
one revolution. To always view the display in relation to 360 degrees, set
MD 30320: DISPLAY_IS_MODULO as well. If the motor encoder of the 611D is
used for the encoder matching, then the matching must be entered for each
gear step if there are several gear steps present. The maximum multiple of the
611D drive is always used as the maximum multiple of encoder markings. This
multiple is 2048.
Table 6-25
Machine data for encoder matching
Machine data
6
Spindle
Encoder on motor
Encoder on spindle
30300:
IS_ROT_AX
1
1
31000:
ENC_IS_LINEAR
0
0
31020:
ENC_RESOL
Marks/rev.
Marks/rev.
31040:
ENC_IS_DIRECT
0
1
31050: DRIVE_AX_RATIO_DENOM
Load rev.
See following note
31070:
DRIVE_ENC_RATIO_DENOM
encoder rev.
encoder rev.
31080:
DRIVE_ENC_RATIO_NUMERA
Motor rev.
Load rev.
31060:
DRIVE_AX_RATIO_NUMERA
Motor rev.
See following note
31050:
DRIVE_AX_RATIO_DENOM
Load rev.
See following note
Note
These MD are not required to match the encoder, but they must be entered
correctly for the sake of setpoint calculation. The load revolutions are entered in
MD 31050: DRIVE_AX_RATIO_DENOM and the motor revolutions in
MD 31060: DRIVE_AX_RATIO_NUMERA.
6-118
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
Example A for
encoder matching
Spindle with raw signal encoder (500 pulses) attached directly to the spindle.
Internal multiple = 2048. Internal calculation resolution = 1000 increments per
degree.
360 degrees
Internal resolution =
MD 31020 * 2048
MD 31080
*
MD 31070
* 1000
360 * 1 * 1000
0,3515
Internal resolution =
500 * 2048 *1
One encoder increment corresponds to 0.3515 internal increments. One
encoder increment corresponds to 0.0003515 degrees (highest possible
positioning resolution).
Example B for
encoder matching
6
Spindle with rotary encoder on the motor (2048 pulses), internal multiple =
2048,
There are 2 gear steps:
Gear step 1: Motor/spindle = 2.5/1
Gear step 2: Motor/spindle = 1/1
Gear step 1
360 degrees
Internal
resolution =
MD 31020 * 2048
MD 31080
*
MD 31070
MD 31050
*
MD 31060
* 1000 incr/degr.
360 degrees
1
1
=
*
*
* 1000 pulses/degr. = 0.034332
2,5
2048 * 2048 pulses 1
Internal
resolution
One encoder increment corresponds to 0.034332 internal increments. One
encoder increment corresponds to 0.000034332 degrees (highest possible
positioning resolution).
Gear step 2
Internal
resolution
Internal
resolution
360 degrees
=
MD 31020 * 2048
MD 31080
*
MD 31070
360 degrees
1
1
=
*
*
1
2048 * 2048 pulses 1
MD 31050
*
MD 31060
* 1000 incr/degr.
* 1000 pulses/degr. = 0.08583
One encoder increment corresponds to 0.08583 internal increments. One
encoder increment corresponds to 0.00008583 degrees (highest possible
positioning resolution).
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-119
03/2006
6 Programming the control
6.9 Axes and spindles
6.9.16
6
Velocities and setpoint matching for spindles
Velocities, gear
steps
With the SINUMERIK 840D, the spindle speed is output in the NCK. The control
contains the data for 5 gear steps. These stages are defined by a minimum and
maximum speed for the stage itself and by a minimum and maximum speed for
the automatic gear step changeover. A new gear step is output only if the newly
programmed speed setpoint cannot be traversed in the present gear step. For
the gear step change, the oscillation times can be specified directly in the NCK
for the sake of simplicity, otherwise the oscillation function must be implemented
in the PLC. The oscillation function is initiated via the PLC.
Speeds for
conventional
operation
The spindle speeds for conventional operation are entered in axis machine data
MD 32010: JOG_VELO_RAPID (conventional rapid feed) and MD 32020:
JOG_VELO (conventional axis velocity). The direction of rotation is specified via
the appropriate directional keys for the spindle on the MCP.
Direction of
rotation
The direction of rotation for a spindle corresponds to the traversing direction for
an axis.
Setpoint matching
The speeds for controlling the drives must be passed to the drives with scaled
values. Scaling in the NCK takes place via the selected load gearbox and via
the drive MD 1401: MOTOR_MAX_SPEED (maximum motor working speed).
In the case of a spindle drive, the maximum motor speed is entered in MD 1401.
The spindle attains the desired speed via the mechanical gear step.
Machine data and
interface signals
MD 35500: SPIND_ON_SPEED_AT_IPO_START
(feed enable for spindles in the setpoint range)
MD 35450:
SPIND_OSCILL_TIME_CCW (oscillation time for
M4 direction)
MD 35440:
SPIND_OSCILL_TIME_CW (oscillation time for M3 direction)
MD 35430:
SPIND_OSCILL_START_DIR (starting direction for oscillation)
MD 35410:
SPIND_OSCILL_ACCEL (acceleration during oscillation)
MD 35400:
SPIND_OSCILL_DES_VELO ( oscillation speed)
MD 35230:
ACCEL_REDUCTION_FACTOR
(reduced acceleration)
MD 35220:
ACCEL_REDUCTION_SPEED_POINT
(speed for reduced acceleration)
MD 35200:
GEAR_STEP_SPEEDCTRL_ACCEL
(acceleration in speed control mode)
MD 35140:
GEAR_STEP_MIN_VELO_LIMIT
(minimum speed for gear step)
MD 35130:
GEAR_STEP_MAX_VELO_LIMIT
(maximum speed for gear step)
MD 35120:
GEAR_STEP_MIN_VELO
(minimum speed for gear step change)
MD 35110:
GEAR_STEP_MAX_VELO
(maximum speed for gear step change)
MD 32020:
JOG_VELO (conventional axis velocity)
MD 32010:
JOG_VELO_RAPID (conventional rapid feed)
MD 31060:
DRIVE_AX_RATIO_NUMERA (numerator for load gearbox)
MD 31050:
DRIVE_AX_RATIO_DENOM (denominator for load gearbox)
NST “control mode”
(DB31, ... DBX84.7)
NST “oscillation mode”
(DB31, ... DBX84.6)
NST “spindle in setpoint range” (DB31, ... DBX83.5)
NST “change gear”
(DB31, ... DBX82.3)
NST “setpoint gear step A to C” (DB31, ... DBX82.0 to DBX82.2)
NST “spindle stop”
(DB31, ... DBX61.4)
6-120
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
NST “setpoint direction anticlockwise”
(DB31, ... DBX18.7)
NST “setpoint direction clockwise”
(DB31, ... DBX18.6)
NST “oscillating speed”
(DB31, ... DBX18.5)
NST “oscillation by the PLC”
(DB31, ... DBX18.4)
NST “no speed monitoring while changing gear”
(DB31, ... DBX16.6)
NST “gear was changed”
(DB31, ... DBX16.3)
NST “actual gear step A to C”
(DB31, ... DBX16.0 to DBX16.2)
NST “traverse buttons plus”
(DB31, ... DBX4.7)
NST “traverse buttons minus”
(DB31, ... DBX4.6)
NST “spindle stop”
(DB31, ... DBX4.3)
Speed
(rev/min)
6
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
ÉÉÉ
Max. spindle speed
Max. speed of gear step 2
Max. speed for gear step 2 changeover
Max. speed of gear step 1
Max. speed for gear step 1 changeover
Min. speed for gear step 2 changeover
Fig. 6-21
Gear
stage 2
Gear
stage 1
Min. speed for gear step 2
Min. speed for gear step 1 changeover
Min. speed for gear step 1
Min. spindle speed
0
Example of speed ranges for automatic gear step selection (M40)
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-121
03/2006
6 Programming the control
6.9 Axes and spindles
6.9.17
Spindle positioning
The control provides an “oriented spindle stop” function with which the spindle
can be moved into a certain position and held there (e.g. for tool changing purposes). Several programming commands are available for this function which
define the approach and program processing.
Reference material:
Functionality
S
S
S
S
/PG/ Programming instructions, basic principles
To absolute position (0–360 degrees)
Incremental position (+/– 999999.99 degrees)
Block change when position reached
Block change on block end criterion
The control brakes the spindle down to creep speed at the acceleration rate for
speed operation. If the creep speed has been reached (IS “Spindle in setpoint
range”), the control branches into position control mode and the acceleration
rate for position control mode and the KV factor become active. The interface
signal “Exact stop fine” is output to indicate that the programmed position has
been reached (block change when position reached). The acceleration rate for
position control mode must be set such that the current limit is not reached. The
acceleration rate must be entered separately for each gear step. If the spindle is
positioned from zero speed, it is accelerated up to a maximum speed corresponding to creep speed; the direction is defined via machine data. The contour
monitoring function is activated as soon as the control mode switches to position control.
6
Machine data and
interface signals
MD 36400:
MD 36050:
MD 36030:
MD 36020:
MD 36010:
MD 36000:
MD 35350:
MD 35300:
MD 35210:
MD 35012:
MD 35010:
MD 32200:
CONTOUR_TOL
(contour monitoring)
CLAMP_POS_TOL
(clamping tolerance)
STANDSTILL_POS_TOL
(zero-speed tolerance)
POSITIONING_TIME
(fine exact stop delay)
STOP_LIMIT_FINE
(fine exact stop)
STOP_LIMIT_COARSE
(coarse exact stop)
SPIND_POSITIONING_DIR
(direction of rotation while positioning from zero speed)
SPIND_POSCTRL_VELO
(cut-out speed)
GEAR_STEP_POSCTRL_ACCEL
(acceleration in position control mode)
GEAR_STEP_CHANGE_POSITION
(gear step change position from software version 5.3)
GEAR_STEP_CHANGE_ENABLE
(gear step change options from software version 5.3
to fixed position)
POSCTRL_GAIN
(KV factor)
MD 20850: SPOS_TO_VDI
(output “M19” to the VDI interface)
NST “positioning mode”
(DB31, ... DBX84.5)
NST “position reached with fine/coarse exact stop” (DB31, ... DBX60.6/60.7)
NST “spindle resynchronized while positioning” (DB31, ... DBX17.4/17.5)
NST “clamping active”
(DB31, ... DBX2.3)
Parameter sets for
exact stop limits
6-122
The fine and coarse exact stop limits can be set for specific parameter sets
using MD 36012: STOP_LIMIT_FACTOR[n] not equal to [1.0].
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
6.9.18
Spindle synchronization
The spindle must synchronize its position with the measuring system. It is always synchronized with the zero marker of the encoder or with a sensor signal
that is connected to the drive module of the SIMODRIVE 611D. MD 34200
ENC_REFP_MODE is used to specify which signal is used for the synchronization (zero marker (0) or sensor (1))
When is
synchronization
necessary?
S After activation of the control if the spindle is moved with a programming
command.
S The “Resynchronize spindle 1/2” signal removes the “Referenced/SynchroS
S
Machine data and
interface signals
nized 1/2” signal that resynchronizes the spindles with the next reference
signal.
After every gear step change (MD 31040: ENC_IS_DIRECT=0)
The spindle goes out of synchronism if a speed above the encoder limit frequency is programmed. When the speed drops to below the encoder limit
frequency, the spindle is re-synchronized. If the synchronized state has
been lost, it is impossible to implement functions such as rotational feedrate,
constant cutting velocity, tapping with and without compensating chuck, positioning and axis modes.
MD 34100: REFP_SET_POS (reference point value, zero marker position). This
MD is used to enter the position of the reference signal for synchronization.
MD 34090: REFP_MOVE_DIST_CORR (reference point move, zero marker
move)
The zero mark offset resulting from the synchronization process is entered here.
MD 34200: ENC_REFP_MODE (position measuring system type)
NST “Resynchronize spindle 1, 2” (DB31, ... DBX16.4 or 16.5)
NST “Referenced/synchronized” 1, 2” (DB31, ... DBX60.4 or 60.5)
Chuck
Motor
Gearing
Power
connection
Toothed belt
Fig. 6-22
Motor
encoder
BERO
Motor encoder cable
MSD module SIMODRIVE 611D
Synchronization via an external reference signal (BERO)
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-123
6
6 Programming the control
6.9 Axes and spindles
03/2006
Note
If the spindle encoder is not attached directly to the spindle and there are gear
ratios between the encoder and the spindle (e,g, encoder on motor), then the
synchronization must take place via a signal from a BERO sensor connected to
the drive module. The control then automatically re-synchronizes the spindle
position after every gear step changeover. The user need not take any further
measures in this respect. The attainable accuracy is impaired by backlash,
elasticity in the gearing and the BERO signal hysteresis, during the
synchronization progress.
If a BERO sensor is used, MD 34200: ENC_REFP_MODE must be set to 2.
6
6-124
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
6.9.19
Spindle monitoring
Axis/spindle
stopped
If the velocity specified in MD 36060: STANDSTILL_VELO_TOL is undershot,
this is indicated via the “Axis/spindle” interface signal.
If MD 35510: SPIND_STOPPED_AT_IPO_START is set, the tool feed is
enabled.
Spindle in setpoint
range
If the spindle reaches the tolerance range specified in MD 35150:
SPIND_DES_VELO_TOL, then the “Spindle in setpoint range” signal is output.
If MD 35500: SPIND_ON_SPEED_AT_IPO_START is set, the tool feed is
enabled.
Maximum spindle
speed
The maximum spindle speed is entered in MD 35100: SPIND_VELO_LIMIT.
The NCK limits the speed to this value. If, however, the speed is exceeded
by the speed tolerance in spite of the NCK limitation (drive fault), then the
IS “Speed limit exceeded” is output together with the alarm “22150 channel
[name] block [number] spindle [number] maximum chuck speed exceeded”.
MD 36200: AX_VELO_LIMIT also monitors the speed of the spindle. An alarm
is generated if the speed is exceeded. In position-controlled mode
(e.g. SPCON) a limitation is set within the control to 90% of the maximum speed
specified by the MD or setting data (control reserve).
Minimum/
maximum gear
step speed
The maximum speed of the gear step is entered in
MD 35130: GEAR_STEP_MAX_VELO_LIMIT and the minimum speed is
entered in MD 35140: GEAR_STEP_MIN_VELO_LIMIT. The speed cannot
leave this range when the appropriate gear step is engaged.
Programmable
spindle speed
limits
The functions G25 S... are used to set a minimum spindle speed and G26 S... to
set a maximum spindle speed limit via the program. The limitation is active in all
operating modes.
Function LIMS=... allows a spindle speed limit for G96 (constant cutting velocity)
to be specified. This limitation is operative only when G96 is active.
Maximum
encoder limit
frequency
The maximum encoder limit frequency (MD 36300: ENC_FREQ_LIMIT) is monitored. If this limit is exceeded, the synchronization is lost and the spindle functionality reduced (thread, G95, G96). It is resynchronized automatically for the
position measuring systems that have become unsynchronized as soon as the
encoder frequency falls below the value in MD36302: ENC_FREQ_LIMIT_LOW. The encoder limit frequency value must be set such that the mechanical encoder speed limit is not exceeded or else the synchronization from high
speeds will be incorrect.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-125
6
03/2006
6 Programming the control
6.9 Axes and spindles
MD 36300 ENC_FREQ_LIMIT
MD 36200 AX_VELO_LIMIT
MD 35100 SPIND_VELO_LIMIT
MD 35130 GEAR_STEP_MAX_VELO_LIMIT
Speed
n
MD 35110 GEAR_STEP_MAX_VELO
Programmable spindle speed limitation G26
Programmable spindle speed limitation G92
Programmable spindle speed limitation G25
MD 35120 GEAR_STEP_MIN_VELO
MD 35140 GEAR_STEP_MIN_VELO_LIMIT
MD 36060 STANDSTILL_VELO_TOL
NST “Axis/spindle stationary” (DB31, ... DBX61.4)
Spindle speed range
Speed range of active gear step
Speed range limited by G25 and G26
Speed range for constant cutting velocity by G92
NST “Referenced/synchronized” (DB31, ... DBX60.4/60.5)
Actual speed monitoring
Maximum spindle speed
6
Fig. 6-23
6-126
Areas for spindle monitoring
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.9 Axes and spindles
03/2006
6.9.20
Example: Starting up NCK I/Os
Table 6-26
Analog
Out
OUTA [1]
Starting up NCK I/Os, drive no.: 4
Analog
In
INA [1]
Analog
In
INA [2]
8 Bits
Out
OUT [9]
16 Bits
Out
OUT [18]
...
OUT [17]
16 Bits
In
IN [9]
...
OUT [33]
...
IN [17]
1. Assign the logical drive number: 4,
select the module type: DMP-C.
2. To connect to the bus, set NCK Reset.
6
3. Set the number of analog inputs and outputs:
analog inputs: MD10300 = 2, analog outputs: MD 10310 = 1.
Set the number of digital inputs and output bytes:
3 bytes dig. inputs, of which 2 bytes are external, 1 byte internal:
MD10350 = 3,
4 bytes dig. outputs, of which 3 bytes are external, 1 byte internal:
MD10360 = 4.
4. Assign the analog inputs to the hardware:
MD 10362 [0] = 01040201
1st input byte
Slot on terminal block
Logical drive number
for 840D always = 01
MD 10362 [1] = 01040301
5. Assign the analog outputs to the hardware:
MD 10364 [0] = 01040101
6. Assign the digital inputs to the hardware:
MD 10366 [0] = 01040602
2 input bytes
Slot on terminal block
Logical drive number
for 840D always = 01
7. Assign the digital outputs to the hardware:
MD 10368 [0] = 01040401
MD 10368 [1] = 01040502
8. Set the weighting factors for the analog inputs / outputs:
MD 10320 = 10000
MD 10330= 10000
9. Set the option: Programmed analog output
10. Program:
$A_OUTA [1] = 5000
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-127
03/2006
6 Programming the control
6.9 Axes and spindles
(Set analog output 1 to 5000 mV)
FROM $A_INA [1] > 4000 DO $A_OUT [9] = TRUE
(If analog input 1 > 4000 mV, set output 9)
R1 = $A_INA [1]
(Set value of analog input 1 in R parameter 1)
DO $A_OUT [9] = FALSE
(Reset digital output 9)
DO $A_OUTA [1] = 0
(Set analog output 1 to 0 mV)
6
6-128
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
03/2006
6.10
Linear motors (1FN1 and 1FN3 motors)
6.10.1
General information for starting up linear motors
Recommended reading
Detailed information about linear motors, encoder and power connections, and
configuration and monitoring can be found in:
Reference material:
/PJLM/ Configuration guide for linear motor
6
Checks in deenergized state
The following should be checked:
1. General linear motor check
–
Which linear motor is used?
–
Is the motor included in the list?
–
If yes,
type: 1FN_ _ _ _ -_ _ _ _ _-_ _ _ _
If no,
determine the manufacturer’s data
for the non-Siemens linear motor
Is the cooling system functional and is the correct coolant mixture in
use? (Recommended mixture: 75% water, 25% Tyfocor).
2. Mechanical system
–
Can the axis travel freely across the entire traversing range?
–
Do the installation dimensions of the motor and the air gap between the
primary and secondary sections comply with the manufacturer’s specifications?
–
Vertical axis:
If the axis has a counterweight, is it functional?
–
Brake:
If a brake is fitted, is it being applied and released properly?
–
Travel limitation:
Are mechanical limit stops installed at both ends of the travel path and
bolted securely in position?
–
Are the moving cables installed properly in a cable trailing device?
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-129
03/2006
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
3. Measuring system
Is an incremental or an absolute (EnDat) measuring system installed?
a) Incremental measuring system:
_ _ _ _ _ _ mm
– Grid size
– Number of zero markers _ _ _ _ _ _
b) Absolute measuring system:
_ _ _ _ _ _ mm
– Grid size
Determine the positive drive direction:
Which is the positive counting direction of the measuring system? (see
subsection 6.10.6)
––> Invert actual velocity value? j yes j no
4. Wiring
6
–
Power section (connection with phase sequence UVW, clockwise
rotation)
–
PE conductor connected?
–
Shield attached?
–
Various methods of temperature sensor evaluation
a)
Evaluation by KTY84 via SIMODRIVE 611Donly
b)
Evaluation via SIMODRIVE 611D and external
c)
External evaluation only
Note:
In case a) a temperature sensor coupling lead (dongle) must be connected between –X411 and the measuring system.
Reference material:
/PJLM/CON/ General notes on connections:
“Encoder connection” section
5. Measuring system cable
Check whether the measuring system cable is correctly attached to connector X411 or to the adapter on the temperature sensor coupling lead.
See also:
Reference material:
6-130
/PJLM/CON/ General notes on connections:
“Encoder connection” section
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
03/2006
6.10.2
Start-up: linear motor with a primary section
Start-up procedure
!
Linear motors with one primary section (single motor) must be started up using
the start-up tool as described below:
Warning
For safety reasons, the pulse enabling signal on the closed-loop control unit
(term. 663) must be switched off initially before the drive is switched on.
1. Configure the drive:
–
Select drive type: “SLM” (synchronous linear motor) ––> Add module
–
Select the power section
Fig. 6-24
Drive configuration for synchronous linear motor
 Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-131
6
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
03/2006
2. Adapt the axis-specific machine data (MD) as for feed drive
6
Fig. 6-25
Minimum selection of axis machine data for linear motor
Please observe the following safety information:
Note
You must check the following before activating the pulse and servo enables:
S Ensure that the encoder parameters are correct, especially if it is necessary
to invert the actual speed or velocity value.
Check that the actual speed or velocity value has the correct sign and that
the actual position value counts up or down correctly by pushing the motor
manually.
Note that the speed inversion should also be programmed on the NCK side
(axis-specific data, MD 32110 – ENC_FEEDBACK_POL[0] = –1).
S When performing initial trials with rotor position identification based on a
moving system, it is advisable to reduce the current for safety reasons, e.g.
to 10% (MD 1105 = 10%). The current reduction does not take effect until
the identification is effective.
6-132
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
03/2006
3. Select the motor
Message 300701: “Start-up required” must appear before the motor is selected (Fig. 6-26).
a) Is the linear motor included in the list of linear motors?
If yes: Select the motor
(parallel-connected linear motors start with 2x1FN. ...)
6
Fig. 6-26
Selecting a motor for which the data is already listed
 Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-133
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
03/2006
b) Is the linear motor not included in the list of linear motors?
––> “Non-Siemens motor”
“Motor” field ––> enter data
Note
If a smaller identification current is needed (<40%), alarm 300753 must be
hidden with bit 5 in MD 1012.
6
Fig. 6-27
Entering the unlisted motor, the data is not yet specified
Enter the motor data:
Fig. 6-28
6-134
Entering data for an “unlisted motor”
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
03/2006
4. “Measuring system/encoder” dialog
Select the motor measuring system and enter the encoder data
a) Incremental encoder
6
Fig. 6-29
Data entry for incremental measuring system with rotor position identification
Enter encoder data
The following selection can be made in the “Linear measuring system” field:
–
Incremental – one zero marker
There is an incremental measuring system with 1 zero marker in the traveling range.
–
Incremental – several zero markers
There is an incremental measuring system with several zero markers in
the traveling range.
–
Incremental – no zero marker
There is an incremental measuring system with no zero marker in the
traveling range.
“Invert actual velocity value”: yes/no (section 6.10.6)
Enter “Graduations” of measuring system
“Coarse synchronization with” field:
–
Rotor position identification: yes (for incremental measuring system
only)
Confirm acceptance of data with OK ––> “Save bootfile” and select “NCK
reset”.
 Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-135
03/2006
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
b) Absolute encoder (EnDat)
An absolute measuring system (EnDat interface) is installed.
6
Fig. 6-30
Data entry for absolute measuring system, e.g. LC181
The following data must be entered:
–
Select Absolute (EnDat interface) from the “Linear measuring system”
box.
–
“Invert actual velocity value” (subsection 6.10.6)
–
Enter “Graduations” of measuring system
Confirm acceptance of data with OK ––> “Save bootfile” and select “NCK
reset”.
5. Fixed temperature?
If the temperature monitor is evaluated not via the drive, but by an external
device (see subsection 6.10.5), the monitoring function must be switched off
by entering a fixed temperature > 0.
–
MD 1608
e.g. 80_
Monitoring off
–
MD 1608
e.g. 0_
Monitoring on
6. Reduce maximum motor current for safety reasons
–
!
MD 1105 (maximum motor current) = e.g. enter 20%
Danger
Linear drives are capable of significantly higher acceleration rates and velocities than conventional drives.
The traversing range must be kept clear of obstacles at all times to protect
operating personnel and the machine itself.
6-136
 Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
03/2006
7. Determine the commutation angle offset
The commutation angle offset is determined as follows:
a) Select identification method via MD 1075. Possibly adapt other
machine data for rotor position identification.
b) Save the boot files and perform NCK reset.
c) Depending on which measuring system is used, continue as follows:
Incremental
measuring system
With an incremental measuring system:
START
Yes, Hall sensor
boxes present
No, Hall sensor boxes
not present
Are Hall sensor
boxes present?
6
If the enables are set, a rotor position identification
is carried out immediately.If the rotor position identification is unsuccessful, the appropriate error message is output. Once the causes of the fault have
been eliminated and the error message acknowledged, another attempt at identification is made.
The coarse synchronization is obtained from the
Hall sensor signals (C/D
track) on switching on
Several zero markers with cams
or distance-coded reference
markers from VSA 06.07.07
One zero marker
Zero markers?
Set MD 1017 (”Start-up help”) to 1
Reference axis on the NCK side
Set MD 1017 (”Start-up help”) to 1
No zero marker, several zero markers without cam distance-coded
reference markers from up to VSA
06.07.07
When it moves over the zero marker, the commutation angle offset
is entered in MD 1016
When it moves over the zero marker, the commutation angle offset
is entered in MD 1016
Alarm 300799 appears (”Save boot
files and perform NCK reset”)
Move axis over the zero marker,
“JOG” operating mode
There is no selection of the zero
marker and the commutation angle
offset is not accepted
Alarm 300799 appears (”Save boot
files and perform NCK reset”)
Save boot files and perform
NCK reset
Save boot files and perform
NCK reset
End
Fig. 6-31
Incremental measuring system
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-137
03/2006
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
Absolute
measuring system
With an absolute measuring system:
START
1FN1 linear motor
Motor type?
If the EnDat serial number read by the
measuring system is not equal to MD 1025
then MD 1017 is not set and
alarm 300604 appears
(”Motor encoder is not aligned”)
If the EnDat serial number
read by the measuring system
is not equal to MD 1025, then MD 1017
is automatically set to 1
6
1FN3 linear motor
Yes, secondary conditions met
(MD1075 must be set to 3!)
Set MD 1017 to 1,
Acknowledge alarm 300604
If the enables are set, a rotor position identification is performed immediately. If the rotor
position identification is not successful, an
error message is output. When the causes of
the error have been remedied and
the error message is acknowledged, a new
identification attempt is made.
The commutation angle offset
is automatically entered
in MD1016
Secondary conditions for
motion-based
rotor position identification met?
No, secondary conditions
not met
The commutation angle offset must
be determined with instrumentation (see
subsection 6.10.8) and entered
manually in MD 1016
Set MD 1017 to –1
The EnDat serial number is read
by the measuring system and entered
automatically in MD1025
Alarm 300799 appears (”Save
bootfiles and perform NCK reset”)
Save boot files and
Execute NCK reset
End
Fig. 6-32
6-138
Absolute measuring system
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
03/2006
Distance-coded
measuring system
This measuring system is not supported by the SIMODRIVE 611D. Several zero
markers must be selected incrementally.
Note
With non-Siemens motors, the rotor position identification method cannot be
guaranteed to determine the commutation angle offset. Depending on the
design of the motor, the following methods may be used for both types of
measuring system:
S Method based on saturation
S Method based on motion
S With an absolute measuring system: determine the commutation angle
offset using instruments (see subsection 6.10.8).
When the start-up is complete, the commutation angle offset MUST be checked
using instruments.
8. Check and adjust the rotor position identification if a Hall sensor is not used
Note
If a Hall sensor is used it is only possible to verify the results with the aid of
instrumentation (see subsection 6.10.8).
To verify the rotor position identification, a test function can be used to determine the difference between the detected rotor position angle and the actual
angle used by the closed-loop control system. Proceed as follows:
–
Run the test function several times and evaluate the difference
Start
Set MD 1736 (test rotor position identification) = 1
Difference MD 1737 (difference in rotor position identification)
=____,____,____,____,____
–
Is the spread of measured values less than 10 degrees electrical?
No:
Increase MD 1019 (e.g. by 10 %) and repeat
measurements.
If the repetition is OK, then determine the commutation angle offset once
more as follows:
–
With an incremental measuring system:
a)
Incremental – one zero marker
as for point 7. (Determine commutation angle offset)
b)
Incremental – no or several zero markers
Press “Save boot file” and “NCK-Reset”
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-139
6
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
–
03/2006
With an absolute measuring system:
Switch off drive (NCK-Reset)
Switch on drive with pulse and controller enabling signals inhibited
Set MD 1017 = 1
Activate on pulse and controller enable signals
––> The angle offset is automatically entered in MD 1016
––> Alarm 300799 appears
––> Save boot files and perform NCK reset
Example for rotor position identification (see figure below):
6
Fig. 6-33
Result of rotor position identification with absolute measuring system
9. Move axis and check correct function
Does the axis traverse in the correct direction with a positive velocity
setpoint?
–
No
Change MD 32100 (traversing direction)
Is the distance traversed correct? (input = 10 mm ––> distance = 10 mm)
10. Set and perform referencing/adjustment
6-140
–
Incremental measuring system:
Referencing (see subsection 6.9.12)
–
Absolute measuring system:
Adjust (see subsection 6.9.6)
 Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
03/2006
11. Set software limit switch (see subsection 6.9.11 under the heading of
“Monitoring positions via software limit switches”)
12. Optimize axis controller settings
Note:
The automatic controller setting does not produce any useful results for
linear motors since the measuring system mounting has a significant effect
on the control characteristic.
6.10.3
–
Current and speed controllers (see Chapter 10)
–
Position controller (see Chapter 10)
Start-up: linear motors with 2 identical primary sections
6
General
If it is certain that the EMFs of both motors have the same phase relation, then
the motors can be operated on one drive if they have parallel connecting
cables.
The start-up procedure for paralleled linear motors is based on the start-up
operation for a single linear motor.
Initially only one linear motor (motor 1) is connected to the drive and started up
as a single motor (1FNx...). The commutation angle offset is determined either
automatically or with instruments (see subsection 6.10.8) and is noted.
Motor 2 is then connected in place of motor 1 and operated as a single motor.
Again, the commutation angle offset is determined either automatically or with
instruments (see subsection 6.10.8) and is noted.
If the difference between the commutation angle offsets of motor 1 and motor 2
is less than 10 degrees electrical, both motors may be connected to the drive in
parallel and may be operated as a parallel circuit with 2 linear motors
(e.g. 2x 1FN. ...).
Procedure for
starting up
paralleled linear
motors
The start-up sequence for paralleled linear motors is as follows:
1. Disconnect the paralleled motors
Connect only motor 1 to the power section.
2. Start up motor 1 as if it were a single motor
––>
Note the information in subsection 6.10.1
––>
Start up as described in subsection 6.10.2
(including point 7.)
––>
Check the rotor position identification and set
(see subsection 6.10.2, point 8.)
3. Move axis and check correct function
4. Note the commutation angle offset of motor 1
–
MD 1016 (motor 1) = _ _ _ _ _ _ _ _ degrees electrical
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-141
03/2006
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
5. Switch off and wait until DC link has discharged
6. Connect motor 2 to the power section instead of motor 1
Warning:
In a back-to-back arrangement (see section 6.10.7), remember to swap over
phase U and V.
7. Switch on motor with pulse and controller enabling signals inhibited
8. Determine the commutation angle offset of motor 2
6
–
With an incremental measuring system:
(see subsection 6.10.2, point 7.: “Determining the commutation angle
offset”)
–
With an absolute measuring system:
Switch off drive (NCK-Reset)
(see subsection 6.10.2, point 7.: “Determining the commutation angle
offset”)
9. Move axis and check correct function
(see subsection 6.10.2, step 9.)
10. Note the commutation angle offset of motor 2
–
MD 1016 (motor 2) = _ _ _ _ _ _ _ _ degrees electrical
11. Difference between step 4. (motor 1) and step 10. (motor 2)
if v 10 degrees ––>
OK
if u 10 degrees ––>
Check mechanical structure and correct
(see subsections 6.10.4 and 6.10.7)
Delete motor data for individual motor ––> Deleted boot file
12. Switch off and wait until DC link has discharged
13. Set up parallel connection of the 2 linear motors again
Connect both motors to the power section again.
14. Switch on motors with pulse and controller enabling signals inhibited
15. Start-up of paralleled linear motors
–
Carry out the complete start-up procedure described in
subsection 6.10.2
–
Select the paralleled motor from the “Motor selection” dialog.
(2x1FN. ...) or:
Enter the data for the paralleled non-Siemens motor (as described under
the heading of “Non-Siemens motors – parameters for SLM”).
16. Compare the commutation angle offset between motor 1 and 2
–
6-142
Check connection between motor cable and power section, correct if
necessary and determine the commutation angle offset.
With an incremental or absolute measuring system:
As described in subsection 6.10.2, point 7.: “Determining the commutation angle offset”.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
03/2006
6.10.4
Mechanical system
Check the
installation
dimensions
and air gap
Installation dimension e1 or e2 can be checked, for example, by means of
gauge blocks and feeler gauges before the motor is installed.
Note
The applicable installation dimensions can be found in the following
documents:
S /PJLM/ Configuration guide for linear motor
S The data sheet of the appropriate 1FN1 or 1FN3 motor.
Please note with respect to installation dimension and air gap:
The electrical and system-related properties of the linear motor are guaranteed
solely as a function of the installation dimension and not the measurable air
gap. The air gap must be large enough to allow the motor to move freely.
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
e2
e1
l
b
Thermoinsulating
bars
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
Fig. 6-34
Table 6-27
Check dimensions for motor installation illustrated by a 1FN1 motor
Check dimensions for installation dimension and air gap for a 1FN1 linear motor
1FN1 ...
Linear motors
1FN1 07j
Check dimensions
1FN1 12j
1FN1 18j
1FN1 24j
Installation dimension e1 [mm]
80,7 $ 0,3
106,7 $ 0,3
Installation dimension e2 [mm] (without thermo-insulating bars)
76,7 $ 0,3
101,7 $ 0,3
+0.3/
–0.45
Measurable air gap l [mm] (not including installation dimension tolerance)
1.1
Distance b [mm] (not including installation dimension tolerance)
13 $ 1
1.1 +0.3/–0.45
13 $ 1
For installation dimensions of 1FN3 linear motors, see dimension drawings in
appendix of 1FN Planning Guide, mounting height hM or hM1.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-143
6
03/2006
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
6.10.5
Temperature sensors for 1FN1 and 1FN3 motors
Description for
1FN1
The following temperature sensing system is integrated in the primary section of
1FN1 motors:
1. Temperature sensor (KTY 84)
The KTY 84 temperature sensor has an approximately linear characteristic
(580 ohms at 20 °C and 2.6 kohms at 300 °C).
2. Temperature switch (3 series-connected NC contacts)
A switch with a two-position characteristic and an operating temperature of
120 °C fitted for each winding overhang.
The temperature switch is generally only used for parallel connections or
protective separation.
6
The switches can be evaluated additionally by a higher-level external control
(e.g. a PLC). This option is recommended if the motor is frequently loaded at
maximum force at standstill.
As a result of different current levels in the 3 phases, different temperatures
(by as much as 15 K) may occur in the individual winding overhangs; only
temperature switches are capable of sensing them reliably.
Description for
1FN3
The following temperature sensing system is integrated in the primary section of
1FN3 motors:
1. Temperature sensor (KTY 84)
The KTY 84 temperature sensor has an approximately linear characteristic
(580 ohms at 20 °C and 2.6 kohms at 300 °C).
2. PTC thermistor detector
A temperature sensor for each phase is integrated in the winding overhangs.
The operating temperature of the PTC sensor is 120 °C.
The 3RN1 thermistor motor protection control unit is the preferred option for
evaluating PTC detectors.
Note
If the temperature sensors or switches are not connected, they must be shortcircuited and connected to PE as protection against electrical damage and high
touch voltages.
!
Important
When connecting up the temperature monitoring circuits, please read the specifications according to DIN EN 50178 regarding protective separation.
For information about protective separation, please refer to:
Reference material:
6-144
/PJLM/ Configuration guide for linear motor
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
03/2006
How are the temperature sensors
evaluated?
The signal leads for motor temperature monitoring on 1FN motors are installed
not in the encoder cable, but in the motor power cable. In order to sense the
winding temperature of the drive, the temperature sensor signal leads must be
looped into the encoder cable (temperature sensor coupling lead).
Linear scale
Case a)
The temperature is monitored
via the drive.
Pin 25
SIMODRIVE
611 D
Pin 13
–X411
Case b)
The temperature is monitored via the drive and
an external device.
Temperature sensor
coupling lead
Drive A
Brown
+ black
Orange
+ red
U2 V2 W2 PE
S
Temperature sensor via drive
S
External temperature switch on 1FN1
S
6
On 1FN3 with PTC resistors via
control unit
Red
SIMODRIVE
611 D
Power cable
Temperature sensor
coupling lead
1FN
Drive A
Linear scale
Pin 25
–X411
Pin 13
Yellow
White
Black
Linear scale
U2 V2 W2 PE
Drive A
U2 V2 W2 PE
Red
Black
Evaluation
external
Yellow
SIMODRIVE
611 D
White
Brown
+ black
Orange
+ red
–X411
Evaluation
external
Power cable
Red
Yellow
White
Black
1FN
Case c)
Power cable
The temperature is monitored
via an external device only.
1FN
Fig. 6-35
Evaluation of KTY temperature sensor (black/white) and switch or PTC (yellow/red)
(whether temperature switch or PTC resistor depends on motor type, i.e. 1FN1 or 1FN3)
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-145
03/2006
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
Note
The outer and inner shielding of the signal lines in the power cable and the
shielding for the temperature sensor coupling lead MUST be laid flat on the
shielding connecting plate.
Failure to connect the shield correctly can result in high touch voltages, malfunctions and sporadic errors or irreparable damage to the closed-loop control
module.
Table 6-28
Assignments of temperature sensor coupling lead
Signal
6
Power cable
Temperature sensor coupling lead
(dongle)
–X411
on drive
Temperature sensor +
Black core
Brown + black core
Pin 13
Temperature sensor –
White core
Orange + red core
Pin 25
Temperature switch/PTC
Yellow core
–
–
Temperature switch/PTC
Red core
–
–
6-146
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
03/2006
6.10.6
Measuring system
Determining the
control direction
The control direction of an axis is correct if the positive direction of the drive
(= CW rotating field U, V, W) coincides with the positive count direction of the
measuring system.
Note
The instructions for determining the drive direction apply only to Siemens
motors (1FNx motors).
If the positive direction of the drive and the positive counting direction of the
measuring system do not coincide, then the actual speed value must be inverted in the “Measuring system/Encoders” dialog during start-up (MD 32110).
It is also possible to check the control direction by parameterizing the drive first
and then moving it manually with the enabling signals inhibited.
If the axis is moved in a positive direction (see definition in Fig. 6-36), then the
actual velocity value must be counted positively.
Determining the
drive direction
The direction of the drive is positive if the primary section moves in the opposite
direction to the outgoing cable in relation to the secondary section.
+
Primary section
Outgoing cable direction
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
Secondary section (solenoids)
+
Secondary section (solenoids)
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
Primary section
Fig. 6-36
Determining the
count direction of
the measuring
system
Outgoing cable direction
Determining the positive direction of the drive
The method by which the count direction is determined depends on the measuring system itself.
1. Heidenhain measuring systems
Note
The count direction of the measuring system is positive if the distance between
the scanning head and the rating plate increases (see Fig. 6-37).
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-147
6
03/2006
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
Scanning head
+
Scale
Fig. 6-37
Rating plate
Determining the count direction of Heidenhain measuring systems
2. Renishaw measuring systems (e.g. RGH22B)
The RGH22B measuring system from Renishaw (grid size = 20 µm) is not
compatible for connection to Heidenhain systems until serial number
G69289. The zero marker on earlier scanning head models cannot be evaluated. Since the reference marker on the Renishaw RGH22B has a direction-dependent position, encoder signals BID and DIR must be parameterized such that the reference marker is output in only one direction. The
direction (positive/negative) is dependent on the geometric configuration on
the machine and the reference point approach direction.
6
Table 6-29
Signal
Signal and pin assignments, routing on 1FN linear motor
Cable color
Round
connector
12-pin
Connected to
+5 V
0V
BID
Black
Pin 9
Reference marker in
both directions
Reference marker in
one direction
DIR
Orange
Pin 7
Positive directions
Negative direction
+5 V
Brown
Pin 12
0V
White
Pin 10
The count direction of the measuring system is positive if the scanning head
moves in the direction of the outgoing cable in relation to the gold strip.
+
Scanning
head
Gold strip
ËËËËËËËËËËËËËËËËËË
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
Fig. 6-38
Measuring system
Determining the count direction of Renishaw measuring systems
Note
If the scanning head is mechanical connected to the primary section, then the
cable exit direction must be different. Otherwise invert the actual value!
6-148
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
03/2006
Temperature
sensor coupling
lead (= dongle)
This connection variant has proved to extremely immune to interference and
should always be employed.
If an incremental measuring system is used, the drive is synchronized coarsely
using the rotor position identification routine.
Encoder cable
–X411
Linear scale
SIMODRIVE
611 D
Drive A
U2 V2 W2 PE
6FX2001-2CG00-xxxx (increment)
6FX2002-2CH00-xxxx (absolute)
Temperature sensor coupling lead (dongle)
6FX2002-1AA14-xxxx
6
Primary section
Power cable
Fig. 6-39
Temperature sensor coupling lead (recommended standard connection)
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-149
03/2006
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
6.10.7
Parallel connection of linear motors
Mechanical
structure
The distances between the motor primary sections must ensure an identical
phase relation of the motor EMFs.
All primary sections are therefore connected cophasally in parallel to the
converter.
6
Secondary
section
n S 2τM
Primary
section
Note:
Same outgoing cable direction
n S 2τM
Secondary
section
Fig. 6-40
τM:
Pole-pair width (see MD 1170)
n:
0, 1, 2, ...
Primary
section
Parallel connection of linear motors (standard configurations)
Back-to-back
arrangement
(special type of
parallel circuit)
With this parallel circuit (back-to-back arrangement), the cables exit from the
individual motors in opposite directions.
xx mm + n S 2τM
Note:
Different cable exit directions
τM:
Pole-pair width (see MD 1170), 1FN107x: τM = 28.2 mm, 1FN11xx and 1FN12xx: τM = 36 mm
n:
0, 1, 2, ...
xx:
Constant dimension (see data sheet from motor manufacturer)
Fig. 6-41
6-150
Parallel connection of linear motors (Janus configuration, special type)
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
03/2006
Temperature sensor and electrical
wiring (see subsection 6.10.5)
The temperature sensors can be evaluated, for example, as follows:
S Temperature sensor
–
Motor 1:
Evaluation via the drive
–
Motor 2:
not connected
(short-circuited and connected to PE)
S Temperature switch or PTC
–
Motor 1 and 2:
External evaluation
Linear scale
Pin 25
SIMODRIVE
611 D
Pin 13
–X411
Temperature sensor
coupling lead
6
External
evaluation
Power cable
Red
Yellow
White
Black
Red
Yellow
White
Black
Brown
+ black
Orange
+ red
Drive A
U2 V2 W2 PE
Power cable
1FN
Motor 1
Fig. 6-42
Motor 2
1FN
Wiring of parallel-connected linear motors
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-151
03/2006
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
6.10.8
Test measurements on linear motors
Why measure?
Checking the
phase sequence
U-V-W
If the linear motor has been started up in accordance with instructions, but
inexplicable error messages still appear, it will be necessary to test all signals by
means of an oscilloscope.
When the primary sections are connected in parallel, EMF_U for motor 1 must
be in phase with EMF_U for motor 2.
The same applies to EMF_V and EMF_W.
This in-phase condition must be checked by means of test measurements.
Procedure for taking test measurement:
S Isolate terminals 48 and 63 on the NE module and terminal 663 on the
6
closed-loop control unit.
S Warning: Wait until the DC link circuit has fully discharged.
S Disconnect power cable from drive. Separate any parallel connection of
primary sections.
S Create an artificial neutral point using 1 kohm resistors.
U
Linear
motor
V
W
1 kΩ
1 kΩ
EMF_W
Fig. 6-43
1 kΩ
EMF_V
EMF_U
Arrangement for test measurements
The phase sequence must be U-V-W with a positive traversing direction.
The direction of the drive is positive if the primary section moves in the opposite
direction to the outgoing cable in relation to the secondary section.
+
Primary section
Outgoing cable direction
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
Secondary section (solenoids)
+
Secondary section (solenoids)
ÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌÌ
Primary section
Fig. 6-44
6-152
Outgoing cable direction
Determining the positive direction of the drive (CW rotating field)
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6 Programming the control
6.10 Linear motors (1FN1 and 1FN3 motors)
03/2006
Determining the
commutation
angle
After connecting the oscilloscope, first move the drive over the zero marker that
the drive is synchronized.
Ch2/Phase V
Ch3/Phase W
Ch1/Phase U
Ch4
6
Fig. 6-45
Determining the commutation angle offset by measuring the EMF and
normalized electrical rotor position via DAC in a positive drive direction
Definition of channels (Ch1 ... Ch4):
S Ch1: EMF Phase U to star point
S Ch2: EMF Phase V to star point
S Ch3: EMF Phase W to star point
S Ch4: Scaled electrical rotor position via DAU measured signal
Note
If you select the “Scaled, electrical rotor position” measured signal, the SHIFT
factor should be changed from 7 to 8 and the offset value from –1.25V to –2.5V.
For a synchronized drive, the difference between the EMF/phase U and the
electrical rotor position should not exceed $10_.
If the difference is greater, the position of the zero marker must be moved in the
software in MD 1016 “COMMUTATION_ANGLE_OFFSET”.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-153
6 Programming the control
6.11 AM/U/F function
6.11
03/2006
AM/U/F function
Note
The AM/ U/F function is described in
Reference material /FBA/ DE1, Description of the drive functions,
Advanced drive functions
/POS3/ SIMODRIVE POSMOfunction guide
/FBU/ SIMODRIVE 611 universal function guide
6
6-154
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
6.12
Concept
6 Programming the control
6.12 System settings for power-up, RESET and starting part programs
System settings for power-up, RESET and starting part
programs
The response of the control changes after the following actions:
S Power-up (POWER-ON),
S Reset/end of part program and
S Start of part program
The following machine data settings affect the above actions:
MD 20110: RESET_MODE_MASK (define the basic control settings
after power-up and reset) and
MD 20112: START_MODE_MASK (define the basic control settings
after start of part program)
Table 6-30
Status
Procedure
6
Changing system settings with MD
can be changed by MD
Power-up (POWER-ON),
RESET_MODE_MASK
RESET/end of part program
RESET_MODE_MASK
Start of part program
START_MODE_MASK and
RESET_MODE_MASK
Select the required system response.
S after power-up (POWER-ON)
MD 20110: RESET_MODE_MASK, Bit 0 =
0 or 1
Power-up
(POWER-ON)
MD 20110
Bit 0=0
RESET_MODE_MASK
Bit 0
– G codes as per MD 20150: GCODE_
RESET_VALUES
– Tool length correction not active
– Transformation not active
– No coupled units active
– No tangential adjustment active
– Non-configured synchronous spindle
coupling is switched off
Bit 0=1
– G codes as per MD 20150: GCODE_RESET_VALUES
– Tool length correction active as per MD 20120: TOOL_RESET_
VALUE, MD 20121: TOOL_PRESEL_RESET_VALUE and
MD 20130: CUTTING_EDGE_RESET_VALUE
– Transformation active as per MD 20140: TRAFO_RESET_VALUE
– No coupled units active
– No tangential adjustment active
– Non-configured synchronous spindle coupling is switched off
Fig. 6-46
System settings after power-up
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-155
03/2006
6 Programming the control
6.12 System settings for power-up, RESET and starting part programs
S after RESET/end of part program
MD 20110: RESET_MODE_MASK, Bit 4–10 =
0 or 1
Bits 4 – 10 may be combined as required.
RESET/
End of part program
MD 20110
RESET_MODE_MASK
Bit 0
6
Bit 0=0
The current settings are
retained. The next time a part program is
started, the following basic setting takes
effect:
– G codes as per MD 20150: GCODE_
RESET_VALUES
– Tool length correction not active
– Transformation not active
– No coupled units active
– No tangential adjustment active
Bit 0=1
Depending on the setting, bits 4 to 10 affect:
– current level
– current variable frame
– active tool offset
– active transformation
– coupled units
– tangential adjustment
– non-configured synchronous spindle coupling
If synchronous spindle coupling is configured, the coupling is
set in relation to MD 21330: COUPLE_RESET_MODE_1.
Fig. 6-47
6-156
System settings after RESET/end of part program
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
6 Programming the control
6.12 System settings for power-up, RESET and starting part programs
S after start of part program
MD 20112: START_MODE_MASK, Bit 4–10 =
0 or 1
Bits 4 – 10 may be combined as required.
Start of part program
MD 20112
START_MODE_MASK
Bit 4 – 10
Bit 4–10
=0
The current settings are
retained in relation to
– current level
– current variable frame
– active tool offset
– active transformation
– coupled units
– tangential adjustment
– non-configured synchronous spindle
coupling
6
Bit 4–10= 1
The current settings are reset in relation to:
– current level
– current variable frame
– active tool offset
– active transformation
– coupled units
– tangential adjustment
– non-configured synchronous spindle coupling
Fig. 6-48
System settings after start of part program
Reference material:
/FB1/ K2, Functional description of the basic machines,
Axes, coordinate systems, frames,
Section: Actual value system in vicinity of
workpiece
J
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
6-157
6 Programming the control
6.12 System settings for power-up, RESET and starting part programs
03/2006
Notes
6
6-158
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
PLC Description
7.1
7
PLC start-up
PLC module
The PLC in the 840D is compatible with the SIMATIC Step7 AS314.
The basic model has 64 KB of memory, which can be upgraded with another
32 KB to make a total of 96 KB (option).
Basic program and
user program
The PLC program is divided into the basic program and the user program. The
entry points for the user program are marked in OBs 1, 40 and 100 of the basic
program.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
7-159
7
03/2006
7 PLC Description
7.1 PLC start-up
ÎÎÎ
ÎÎÎ
ÎÎÎ
ÎÎÎÎ
OB 100
Restart
OB 1
Cyclic
processing
FB 1
Start
User
program
FC 2
BP OB 1
NCK
Mode group
Channel
Axis
Spindle
FC 14
MSTT,
BHG
FC 6
Tool man.
(not FMNC)
7
User
program
FC 19/25
MSTT:
MCP_IFM
MCP_IFT
FC 7/8/22
WZV:
TM_Trans
TM_Dir
FC 17
Star/delta
ÎÎÎ
ÎÎÎ
ÎÎÎ
OB 40
Process
alarm
Fig. 7-1
FC 3
BP_PRAL
FC 10
Error and
operational
messages
FC (9/15/16/18)
ASUP,
con. axes/
spindles
FB 2/3/4
Read/
write var.
PI services
FC 13
BHG:
display cont.
G group
distributor
User
program
Structure of the basic program
Tool box
The basic PLC program is an integral component of the SINUMERIK 840D tool
box.
PLC memory
Set the “PLC memory” option if necessary.
Download PLC
program
There are two ways to download the finished PLC program:
1. Load, test and change the PLC program with SIMATIC STEP7 HiGraph
(also see Readme file on the basic program disk).
2. Download an archived PLC program with PCIN or from the HMI
7-160
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
7 PLC Description
7.1 PLC start-up
03/2006
Note
The STEP7 project manager (S7 TOP) does not display the SDB as standard.
To display the SDB, select “All blocks with SDBs” from the “View” –> “Set filters”
menu.
PLC status
The “Diagnostics” menu includes the PLC status option for controlling and monitoring PLC inputs, outputs, flags, etc.
Starting characteristics of the PLC
The PLC always powers up in RESTART mode, i.e. the PLC operating system
runs through OB100 after initializing and then starts cyclical operation at the
start of OB1. No re-entry takes place at the interruption point (e.g. after power
failure).
RESTART mode
For the flags, timers and counters there are both retentive and non-retentive
areas. Both area types are contiguous, but are separated by a parameterizable
limit, the area with the higher-order address being designated as the non-retentive area. Data blocks are always retentive.
If the retentive area is not buffered (back-up battery empty), then start-up is
blocked. The following operations are performed during a restart:
S Delete IStack, BStack and non-retentive flags, timers and counters
S Delete process output image (POI)
S Reject process and diagnostic alarms
S Update system status list
S Evaluate parameterization objects of modules (from SD100 onwards) or
output default parameters to all modules in single-processor mode
S Process restart OB (OB100)
S Read in process input image (PII)
S Cancel command output disable (BASP)
Cyclical operation
The basic program before the PLC user program is processed. In cyclic operation, the NC/PLC interface is fully processed. At the process alarm level, the
current G functions are transferred to the PLC, if this function is active.
Sign-of-life
monitoring
A cyclic monitoring function is activated between the PLC and NCK once
power-up and the first OB1 cycle have been completed. When the PLC fails,
alarm “2000 sign of life monitoring PLC” is displayed.
Reference material:
/FB1/ P3, Function guide,
PLC basic program powerline
/S7H/ SIMATIC S7-300
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
7-161
7
7 PLC Description
7.2 Overview of the organizational blocks, function blocks, DBs
Parameters
for FB1
03/2006
FB 1 (power-up block for the PLC basic program) must be supplied with
variables.
For an exact description of variables and options for changing parameter
settings, please refer to
Reference material:
/FB1/ P3, Function guide,
PLC basic program powerline
Note
Timers T0 to T9 are used by the basic program.
7.2
7
Overview of the organizational blocks, function blocks,
DBs
Reference material:
/FB1/ P3, Function guide,
PLC basic program powerline
J
7-162
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Alarm and Message Texts
8
To allow alarm and message texts to be easily modified to suit the requirements
of a specific automation system, the alarm and message texts are stored in
ASCII format in freely accessible text files.
8.1
Alarm text files for HMI Embedded
Description
When the HMI Embedded application diskette is installed (see chapter 12), the
8
S configuration settings,
S texts,
S the configured interface and
S the user software
are transferred from the update directory on your PC/PG to the PCU 20 hardware. The ways in which the alarm text files can be adapted beforehand are
described here.
Preconditions
S PC with DOS 6.x
S V.24 cable between the COM1 port on the PCU (X6) and the COM1 or
COM2 port on your PC
S Approx. 3 MB free space on hard disk
S The following description assumes that you have already transferred the
software from the HMI Embedded application diskette (diskette 2) to the
hard disk of the PC/PG (as described in chapter 12).
Alarm texts/
message texts
The texts are stored with the Siemens defaults n the selected drive on your PC.
For the sake of simplicity, it is assumed that this is always C: in the following
description. The directory is:
C:\mmc 100 pj\proj\text\<LANGUAGE DIRECTORY>
Depending on the selected language, one of the following letters stands for
<LANGUAGE DIRECTORY>:
D
for German
G
for English
F
for French
E
for Spanish
I
for Italian.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
8-163
03/2006
8 Alarm and message texts
8.2 Alarm text files for HMI Advanced
Files
The text file names start with “a” and end in the extension .txt.
–
ALZ.TXT
Cycle alarm texts
–
ALC.TXT
Compile cycle alarm texts
–
ALP.TXT
PLC alarm/message texts
Editor
The DOS editor “edit” should be used for editing.
The standard texts contained in the text files can be overwritten by user-specific
texts. An ASCII editor, e.g. DOS editor, must be used for this purpose. New
entries can be added to alarm text files.
Please refer to Section 8.3 for the applicable syntax rules.
Multiple languages
HMI Embedded may be set up online with two languages. These are referred to
as the foreground and background languages.
The foreground and background languages of the HMI system can be changed
using the application diskette, as described in chapter 12, “Changing the Software and Hardware”.
During installation, it is possible to select any combination of two of the
languages on the application disk as the foreground and background
languages.
8
Master language
The master language is German. It defines the number and order of the alarm/
message texts for the languages selected by the user.
The number and order of the alarm/message texts in the selected languages
must be identical to those of the master language.
Converting and
transferring
Once you have made the changes, you must then convert the text files and
transfer them to the PCU 20 (chapter 12).
Note
For the user, 128 KB are available for additional text files.
8.2
Alarm text files for HMI Advanced
Storing the text
files
The files with the error texts are stored in the C:\dh\mb.dir\ directory on the hard
disk. The error text files intended for use are activated in file c:\mmc2\mbdde.ini.
Structure of
MBDDE.INI
Extract from mbdde.ini, of relevance for configuring the alarm text files:
8-164
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
8.2
8 Alarm and message texts
Alarm text files for HMI Advanced
...
[Text files]
MMC=c:\dh\mb.dir\alm_
NCK=c:\dh\mb.dir\aln_
PLC=c:\dh\mb.dir\alp_
ZYK=c:\dh\mb.dir\alc_
CZYK=c:\dh\mb.dir\alz_
UserHMI=
UserNCK=
UserPLC=c:\dh\mb.dir\myplc_
UserZyk=
UserCZyk=
...
Standard text files
The standard texts are stored in ASCII format in the following files on the hard
disk of the PCU 50/ 50.3/ 70.
HMI
NCK
PLC
ZYK
CZYK
C:\dh\mb.dir\alm_XX.com
C:\dh\mb.dir\aln_XX.com
C:\dh\mb.dir\alp_XX.com
C:\dh\mb.dir\alc_XX.com
C:\dh\mb.dir\alz_XX.com
In these file names, “XX” stands for the code of the appropriate language.
The standard files should not be changed by the user to store his or her own
error texts. If these files were replaced with new files during a software upgrade
of the HMI, any added or modified user-specific alarms will be lost. The user
should store his own error texts in user files.
User files
The user can replace the error texts contained in the standard files with his own
texts or add new texts. To do this, the additional files must be downloaded to the
c:\dh\mb.dir directory (MBDDE alarm texts) via the Utilities area. The names of
these text files are set in file c:\mmc2\mbdde.ini The “Diagnostics” –> “Start-up”
–>“HMI” area contains an editor for this purpose.
Sample configurations for two additional user files (texts for PLC alarms, modified alarm texts NCK) in the MBDDE.INIfile
...
User HMI =
User NCK = C:\dh\mb.dir\mynck_
User PLC = C:\dh\mb.dir\myplc_
User ZYK =
User CZYK =
...
The texts from the user files overwrite standard texts with the same alarm number. Alarm numbers which do not already exist in the standard texts are added.
Editor
An ASCII editor (e.g. the DOS editor “edit”) must be used for editing files.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
8-165
8
03/2006
8 Alarm and message texts
8.2 Alarm text files for HMI Advanced
Language-specific
nature of the alarm
texts
Example
The language for the user alarm texts is assigned via the name of the text file.
The appropriate code and the extension .com are added to the user file name
entered in mbdde.ini:
myplc_gr.com
mynck_uk.com
Language
Code
German
gr
English
uk
French
fr
Italian
it
Spanish
sp
File for German PLC alarm texts
File for English NCK alarm texts
Note
Changes to alarm texts do not take effect until the HMI has powered up again.
8
When you create the text files, make sure that the date and time are set correctly on the PC, otherwise the user texts may not be displayed on screen.
Example for HMI
Advanced
File with German user texts, PLC:
myplc_gr.com
700000 0 0 “DB2.DBX180.0 set”
700001 0 0 “No lubrication pressure”
The maximum length of an alarm text is 110 characters for a 2-line display.
8-166
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
8.3
8.3
8 Alarm and message texts
Syntax for alarm text files
Syntax for alarm text files
Alarm numbers
The following alarm numbers are available for the cycle, compile cycle and PLC
alarms:
Table 8-1
Alarm numbers for cycle, compile cycle and PLC alarms
Number range
Designation
60000–60999
Effect
Cycle alarms
(Siemens)
61000–61999
62000–62999
63000–64999
Reserved
65000–65999
Cycle alarms
(
(user)
)
66000–66999
67000–67999
Format of the text
file for cycle alarm
texts
68000–69000
Reserved
70000–79999
Compile cycle alarms
400000–499999
PLC alarms general
500000–599999
PLC alarms for channel
600000–699999
PLC alarms for axis and
spindle
700000–799999
PLC alarms for user
800000–899999
PLC alarms for sequence
cascades/graphs
Clear
Display, lock NCK start
Reset
Display, lock NCK start,
motion stopped
Reset
Display
Cancel
Display, lock NCK start
Reset
Display, lock NCK start,
motion stopped
Reset
Display
Cancel
The range of numbers given in the list is not available with every number, see
Reference material:
Table 8-2
/FB1/ P3, PLC basic program powerline,
/LIS1/ Lists
Structure of text file for cycle alarm texts
Alarm number
Display
Help ID
Text or alarm number
60100
1
0
“No D number %1 is programmed”
60101
1
0
60100
...
...
...
...
65202
0
1
“Axis %2 in channel %1 is still moving”
// Alarm text file for cycles in German
Alarm number
List of alarm numbers
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
8-167
8
03/2006
8 Alarm and message texts
8.3 Syntax for alarm text files
Display
This number defines the alarm display type:
0: Display on the alarm line
1: Display in a dialog box
Help ID
HMI Advanced only (PCU 50/ 50.3/ 70, with hard disk): The default assignment
of “0” means that the WinHelp file supplied by Siemens gives a detailed
explanation of the alarm. A value between 1 and 9 refers to a WinHelp file
created by the user via an allocation table in the MBDDE.INI file. See also
Subsection 8.3.1, HelpContext.
Text or
alarm number
The associated text is given in inverted commas with the position parameters.
S You must not use the “ and # characters in alarm texts.
The % character is reserved for displaying parameters.
S If an existing text is to be used, this can be done with a reference to the
corresponding alarm. 6-digit alarm number instead of “Text”.
S The alarm text file may contain comment lines which must start with “//”. The
maximum length of the alarm text is 110 characters for a 2-line display. If the
text is too long, it is truncated and the symbol “*” added to indicate missing
text.
S Parameter “%K”: Channel number (2nd digit of the alarm number)
8
Parameter “%A”: The parameter is replaced by the signal group number
(e.g. axis no., user range no., sequence no.)
Parameter “%N”: Signal number
Parameter “%Z”: Status number
Format of the text
file for PLC alarm
texts
The ASCII file for PLC alarm texts has the following structure:
Table 8-3
Structure of text file for PLC alarm texts
Alarm
no.
Display
Help ID
Text
Text in HMI
510000
1
0
“Channel %K FDDIS all”
Channel 1 FDDISd all
600124
1
0
“Feed disable axis %A”
Feed disable axis 1
600224
1
0
600124
Feed disable axis 2
600324
1
0
600224
Feed disable axis 3
703210
1
1
“User Text”
User Text
1
1
“User Text %A ...”
User Text
Axis 1 ...
...
703211
// Alarm text file for PLC alarm
Alarm number
The alarm number is made up of the event number (2 digits), signal group
(2 digits) and the signal number(2 digits). These parameters are components of
a diagnostic element on the AS315.
Reference material:
8-168
/FB1/ Function manual for basic machines,
P3: PLC basic program powerline (P3 Pl)
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
8.3
Event number
Display
8.3.1
8 Alarm and message texts
Syntax for alarm text files
Signal group
Signal number
5 x (for channels)
00–03
11–16
21–28
(inhibits)
(GEO axes)
(additional axes)
00–99
60 (for axis and spindle)
01–18
(axis no.)
00–99
70 (for user)
00–09
(user no.)
00–99
80 (status graph alarms)
00–99
(graph group)
00–99 (graph no.)
This number defines the alarm display type:
0: Display on the alarm line
1: Display in a dialog box
Alarm list properties
In addition to the current alarms, the user interface also displays an alarm log
containing all the alarms that have previously occurred in the form of a list. You
can modify the properties of the alarm list in the MBDDE.INI file.
Table 8-4
Sections of the MBDDE.INIfile:
Meaning
Section
Alarms
General information about the alarm list (e.g. time/date format of
messages)
Text files
Path/file of the text lists for the alarms (e.g. MMC=..\dh\mb.dir\alm_
<signal block in the mb dir.)
HelpContext
Name and path name of the help files (e.g. File0=hlp\alarm_)
DEFAULTPRIO
Priorities of various alarm types (e.g. POWERON=100)
PROTOCOL
Properties of the protocol (e.g. File=.\proto.txt <name and path of log
file>)
KEYS
Information on keys that can clear alarms (e.g. Cancel+F10 <delete
alarm using the key combination Shift+F10>)
For further details of the file entries, refer to
Reference material:
“Alarms”
/BN/ HMI Programming Package, Part 1
The settings in this section define the following alarm list properties:
S TimeFormat
Enter the format to be used when outputting the date and time. This corresponds to the CTime::format from the Microsoft Foundation Classes.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
8-169
8
03/2006
8 Alarm and message texts
8.3 Syntax for alarm text files
S MaxNo
Defines the maximum size of the alarm list.
S ORDER
Defines the order in which the alarms are added to the alarm list:
FIRST means that more recent alarms are placed at the top of the list,
LAST means that new alarms are placed at the end.
S PLCTIME
Siemens internal variable for PLC software releases older than 3.2. Do not
change the PLCTIME setting.
Example:
[Alarms]
TimeFormat=%d.%m.%y %H:%M:%S
MaxNo=50
ORDER=LAST
PLCTIME=5000
J
8
8-170
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
9
Axis/Spindle Dry Run
9.1
Requirements
Enables for axes
To allow an axis to be moved by the control, enabling terminals on the drive
must be powered and enable bits set at the interface.
Enables on the drive
112
9
63
9
64
9
48
9
663
9
Reference material:
!
Set-up mode
+24 V
Pulse enable
+24 V
Drive enabling command
+24 V
DC-link start
MS (Mains supply) module
+24 V
9
Pulse enable
+24 V
Drive module
/PJU/ Converter Configuration Guide
Warning
Despite the “Axis disable” command via terminal 663, dangerous voltages may
still be present at the drive control output terminals.
The “Axis disable” command via terminal 663 is not suitable for electrical isolation or for use as a drive deactivation mechanism.
Enabling via
PLC interface
The following signals must be made available at the PLC interface for axis or
spindle:
NST “Controller enable”
NST “Pulse enable”
NST “Position measuring system 1 or 2”
(DB31–61, DBX2.1)
(DB31–61, DBX21.7)
(DB31–61, DBX1.5, DBX 1.6)
The following signals on the interface must not be set or else the axis/spindle
motion will be disabled:
NST “Feed/spindle correction switch”
(DB31–61, DBB0) not set to 0%
NST “Axis/spindle disable”
(DB31–61, DBX1.3)
NST “Adjustment mode”
(DB31–61, DBX1.4)
NST “Remaining distance/spindle reset” (DB31–61, DBX2.2)
NST “Feed stop/ spindle stop”
(DB31–61, DBX4.3)
NST “Travel button disable”
(DB31–61, DBX4.4)
NST “Power-up sensor disable”
(DB31–61, DBX20.1)
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
9-171
03/2006
9 Axis/Spindle Dry Run
9.1 Requirements
Reference material: /FB1/ A2, Function Guide,
Various NC/PLC interface signals and functions
Section: Interface signals from and at axis/spindle
Limit switch
Setting of hardware limit switches and interface signal check:
S Hardware limit switch PLUS
DB31–61.DBX12.1
S Hardware limit switch MINUS
DB31–61.DBX12.0
Reference material: /FB1/ A3, Function Guide
Axis monitoring, protection areas,
Section: Monitoring of static limits
9
9-172
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
9 Axis/Spindle Dry Run
9.2 Axis dry run
03/2006
9.2
Axis dry run
Select JOG mode
and enable axis
no
Does the axis
move?
Check the enables at the drive
E/R module:
Terminal 63 (pulse enable)
64 (drive enable)
48 (DC link start)
FDD module:
663 (pulse enable)
Check the interface signals (DB 31 – 61)
DBB0
Feed correction switch
DBX1.7
Correction effective
DBX1.5/1.6
Position measuring system 1/2
DBX1.4
Adjustment mode
DBX1.3
Axis disable
DBX2.2
Delete remaining travel
DBX2.1
Controller enable
DBX4.3
Feed stop/spindle stop
DBX5.0–5.5
JOG–INC
DBX4.6/4.7
Travel buttons
DBX20.1
HLGSS (drive)
DBX21.7
Pulse enable (611D)
Check the machine data
MD 32000–32050 Velocities
MD 36000–36620 Monitoring
MD 32110
Sign for actual value
Service display
9
yes
Is traversing
direction
okay?
no
Check MD 32100: AX_MOTION_DIR
yes
Specified path 10 mm
Is path
evaluation
okay?
no
Check MD 31000 – 31080 (encoder matching)
yes
1
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
9-173
03/2006
9 Axis/Spindle Dry Run
9.2 Axis dry run
1
Traverse with feedrate
1000 mm/min
Traverse in
rapid mode
yes
Alarm?
Interpret alarm and check machine
data for velocity adaptation
no
Following
error
okay?
9
yes
End
9-174
no
Check
MD 32200
(KV factor)
MD 32410
(time constant for jerk limitation)
MD 32910
(dynamic matching)
MD 31050/31060 (load gearbox)
MD 32610
(bias control)
MD 1401
(maximum motor working speed)
MD for velocity matching
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
9 Axis/Spindle Dry Run
9.3 Test of the spindle
03/2006
9.3
Test of the spindle
Enable spindle
(controller enable NC,
enable at the drive)
Specify speed
Does the
spindle rotate?
no
yes
Is traversing
direction
okay?
no
Check the enables at the drive
E/R module
63 Pulse enable
64 Drive enable
48 DC link start
Drive module
663 Pulse enable
Check the interface signals (DB31– 61)
DBB0
Spindle correction
DBX1.7
Correction effective
DBX1.5/DBX1.6
Position measuring system 1/2
DBX1.3
Axis/spindle disable
DBX2.1
Controller enable
DBX16.7
Delete S value
DBX3.6
Velocity/spindle speed
limitation and MD 35160
DBX4.3
Feed stop/spindle stop
DBX20.1
HLGSS
DBX2.2
Spindle reset for MD 35050=1
DBX21.7
Pulse enable
Check the machine and setting data
MD 35100–35150 Spindle speed limitation
MD 36200
AX_VELO_LIMIT
MD 32620
FFW_MODE=4,
then the bit for the torque bias
control must be set in the
drive machine data
SD 41200
JOG_SPIND_SET_VELO
SD 43220
SPIND_MAX_VELO_G26
SD 43210
SPIND_MIN_VELO_G25
Service display
Change MD 32100 AX_MOTION_DIR
yes
Specified speed 100 rev/min
Actual speed
= setpoint
speed?
no
Check MD 31000 – 31080 (encoder matching)
yes
1
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
9-175
9
03/2006
9 Axis/Spindle Dry Run
9.3 Test of the spindle
1
NST
“spindle in setpoint range”
(DB31–61,
DBX83.5)?
Change over
gear stage
no
no
Check the machine data and interface signals
MD 35110–35140 Speeds for gear steps
MD 35150
Spindle speed tolerance
NST “Actual gear step” (DB31–61, DBB16)
NST “Select drive parameter set” (DB31–61, DBB21)
NST “Setpoint gear step” (DB31–61, DBB82)
NST “Active drive parameter set (DB31–61, DBB93)
yes
All gear
stages tested?
yes
Carry out
spindle
positioning?
9
no
End
yes
Position
reached from
high speed and
zero speed?
Change over
gear stage
yes
no
no
Check the machine data
MD 36000
Coarse exact stop
MD 36010
Fine exact stop
MD 32200
KV factor
MD 35210
Acceleration in position control range
MD 35300
Cutout speed
MD 36300
Encoder limit frequency
Check the encoder matching
Check the spindle synchronization (MD 34200)
All gear stages tested?
yes
End
J
9-176
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Drive Optimization
10.1
10
Overview
This tool can be used during initial start-up to input the drive configuration and
assign drive parameters with standard data sets as determined by the motor/
power section combination. It also allows the drive and control data to be
archived on the PG or PC.
Further functions are also provided to assist optimization and diagnosis.
HMI Embedded
With HMI Embedded, the “Start-up Tool” start-up software is used to configure
and assign parameters to the drives.
HMI Advanced
With HMI Advanced, you have the option of carrying out the tuning directly via
the user interface in the “Start-up” area under the “Drives/Servo” menu option.
Start-up:
Drives/Servo
The following functions are available:
10
S Frequency response measurement, speed control loop
S Frequency response measurement, position control loop
S Function generator
S Circularity test
S Servo trace
Measuring
functions
The measuring functions are used to evaluate the most important speed and
position control loop quantities, and to control the torque in the time and frequency range. This is displayed on-screen and no external measuring instruments are necessary.
Analog output
All important control loop signals on the position, speed and torque levels can
also be output with the DAC configuration on external equipment (e.g. oscilloscope, signal recorder) via test sockets on the 810D (611D control).
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-177
03/2006
10 Drive Optimization
10.1 Overview
FFT analysis
(Fourier analysis)
Apart from the usual method of optimizing the control loop machine data based
on transient response, i.e. time characteristics, a particularly powerful tool for
assessing the control loop setting is provided in the form of the integrated
Fourier analysis (FFT) function which also be applied to analyze the given
mechanical characteristics. This tool must be used if
S unsteady current, speed or position signal curves indicate problems with
stability.
S only long rise times can be obtained in the speed loop.
Circularity test
The circularity test is used to analyze the contour accuracy at the quadrant transitions of circular contours achieved by means of friction compensation (conventional or neural quadrant error compensation).
Reference material:
Servo trace
/FB3/ K3 Function manual for advanced functions
Compensation, section: Circularity test
The servo trace is used to analyze the changes over time in servo and drive
data with the aid of graphs. For example:
S Actual position value
S Position setpoint
S Following error
S Contour deviation
10
Saving
measurement
results
10-178
Saving measurement resultsThe measurement diagrams can be archived via
file functions, allowing machine settings to be documented and facilitating remote diagnostics.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.2 Measuring functions
03/2006
10.2
Measuring functions
Explanation
There are a range of measuring functions for displaying the time and frequency
behavior of drives and controls in graph form on screen. Test signals of variable
duration are applied to the drives for this purpose.
Measuring/signal
parameters
The test setpoints are adapted to the application by means of measuring and
signal parameters. The units of these parameters depend on the measuring
function or operating mode. The following conditions apply for the units of these
measuring and signal parameters:
Table 10-1
Quantities and units for measuring and signal parameters
Unit
Quantity
Torque
Specified in percent referred to the peak torque of the power section
used. The torque is calculated for the power section from:
MD 1108 x MD 1113
Velocity/speed
Metric system:
Specified in mm/min or rev/min for linear or rotary motions
Inch system:
Specified in inch/min or rev/min for linear or rotary motions
Distance
Metric system:
Specified in mm or degrees for linear or rotary motions
Inch system:
Specified in inches or degrees for linear or rotary motions
Time
Specified in ms
Frequency
Specified in Hz
10
Note
All the parameters are preceded with 0.
Requirements for
starting measuring
functions
The measuring functions must be started in “JOG” mode to ensure that there
are no accidental traversing motions due to part programs.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-179
03/2006
10 Drive Optimization
10.2 Measuring functions
!
Caution
During the traversing motions made as part of measuring functions, no software limit switches or working field limits are monitored since this is done in
follow-up mode.
Before starting the measuring functions, the user must therefore ensure that
the axes are positioned so that the traveling range limits specified for the measuring functions are sufficient to prevent collision with the machine.
Starting measuring
functions
Measuring functions that trigger a traversing motion can only be selected via the
specific soft key. The measuring function and thus the traversing motion are
always actually started via “NC-START” on the machine control panel.
If you exit the main screen for the measuring function without starting the
traversing motion, the selected traversing function will be canceled.
Once the traversing function has been started, you can exit the main screen
without affecting the function.
Note
“JOG” mode must be selected in order to start measuring functions.
10
Other safety
instructions
10-180
The user is to ensure that, while the measuring functions are in use, that:
–
the “Emergency stop” button is within range
–
there are no obstacles in the traveling range
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.2 Measuring functions
03/2006
Canceling
measuring
functions
The following event cause active measuring functions to be canceled:
–
Hardware limit switch reached
–
Traversing range limits exceeded
–
Emergency stop
–
Reset (mode group, channel)
–
NC stop
–
Removal of controller enable
–
Removal of drive enable
–
Removal of travel enable
–
Park function is selected (in position-controlled mode)
–
Feed override 0%
–
Spindle override 50%
–
Change of operating mode (JOG) or JOG operating mode not selected
–
Pressing the Travel buttons
–
Turning the handwheel
–
Alarms that cause the axes to stop
10
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-181
10 Drive Optimization
10.3 Interface signals: Drive test travel request and Travel enable
10.3
03/2006
Interface signals: Drive test travel request and Travel
enable
Explanation
Axes with a mechanical brake may need the brake to be activated in some
cases. This is done using the Enable with PLC function from the main screen
of the travel function concerned.
In the PLC user program, this can be done with the travel request (NCK→PLC)
signal that is generated when the measuring function is selected.
–
DB31–DB61, ... DBX61.0 “Drive test travel request”
and the acknowledgment signal for the motion enable (PLC→NCK)
–
DB31–DB61, ... DBX1.0 “Drive test travel enable”
can then be linked in the PLC user program as follows.
This safety mechanism can be deselected via the Enable option without PLC.
Reference material:
Deactivating
monitoring
/FB1/ A2, Various NC/PLC interface signals and
functions
The traversing range monitoring function can be deactivated for axes with an
infinite traversing range.
10
10-182
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.4 Frequency response measurement
03/2006
10.4
Frequency response measurement
10.4.1
Scanning the torque control loop
Functionality
It is only necessary to scan the torque control loop for diagnostic purposes in
the event of an error or if standard data was not used for the particular motor/
power section combination, leading to unsatisfactory speed controller frequency
responses.
Note
The user must take special safety precautions before measuring the torque
control loop for vertical axes that have no external weight compensation (drive
must be securely clamped).
Procedure
1. Setting the traveling range monitoring and the enabling logic on the main
screen.
2. Setting the necessary parameters on the measuring parameters screen
3. Displaying the measurement result on screen using the Display soft key
Fig. 10-1
Measuring
parameters
Display diagram: Example of a current control loop
Amplitude
This parameter determines the test signal amplitude (unit: specify the peak
torque as %). Values between 1 and 5% are suitable.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-183
10
03/2006
10 Drive Optimization
10.4 Frequency response measurement
Bandwidth
Analyzed frequency range
S 4.0 kHz for 840D, double axis modules (scanning frequency 16.0 kHz).
S 8.0 kHz for 840D (scanning frequency 16.0 kHz).
Averaging
This value increases both the accuracy of the measurement and the measuring
duration. A value of 20 is normally suitable.
Settling time
Recording of the measured data starts after a delay equal to the set settling
time after activation of the test setpoint. A value of approximately 10 ms is
recommended.
Additional
information
10.4.2
The measuring parameters and measurement results (diagrams) can be loaded
or saved using the File functions soft key.
Scanning the speed control loop
Functionality
The behavior when transferring to the motor measuring system is always
analyzed. Various lists of measuring parameters are offered depending on
which basic setting is selected for the measurement.
Procedure
The traversing range monitoring function is set and the enabling logic (external/
internal) selected in the main screen.
1. Setting the traveling range monitoring and the enabling logic on the
main screen. One of four different types of measurement can be selected:
10
S Reference frequency response
S Interference frequency response
S Setpoint step change
S Disturbance step change
2. Setting the necessary parameters on the measuring parameters screen
3. Displaying the measurement result on screen using the Display soft key
10-184
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.4 Frequency response measurement
03/2006
Fig. 10-2
Guide frequency
response
Display diagram: Example of speed control loop
The guide frequency response measurement determines the transmission
response of the speed controller. The response range should be as wide as
possible and without resonance. It may also be necessary to use stop or lowpass filters (611D). Particular care must be taken to prevent resonance within
the speed controller limit frequency range (stability limit approx. 200-500 Hz).
Interference
frequency
response
Alternatively, the interference frequency response can be recorded to evaluate
the noise suppression of the controller.
Measuring
parameters for
guide and
interference
frequency
response
Amplitude
This parameter determines the test signal amplitude. This should give rise to
only a very low speed of a few (approximately 1 to 2) revs/min at the motor end.
Offset
The measurement requires a low speed offset of just a few motor revolutions
per minute. The set offset must be greater than the amplitude.
From SW 4.1:
S The offset is started up via an acceleration ramp.
S The acceleration value is defined for an
Axis:
Spindle:
S Where:
MD 32300: MAX_AX_ACCEL
MD 35200: GEAR_STEP_SPEEDCTRL_ACCEL
MD 35210: GEAR_STEP_POSCTRL_ACCEL
Acceleration value = 0, no ramp
Acceleration value > 0, ramp active
S The actual measuring function is not activated until the offset value is
reached.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-185
10
03/2006
10 Drive Optimization
10.4 Frequency response measurement
Bandwidth
Analyzed frequency range
S 4.0 kHz for 840D (scanning frequency 8.0 kHz).
Averaging
This value increases both the accuracy of the measurement and the measuring
duration. A value of 20 is normally suitable.
Settling time
Recording of the measured data starts after a delay equal to the value set here
after activation of the test setpoint. A value of between 0.2 and 1 s is recommended.
Setpoint and interference variable
step change
Initiation of the step change can be used to assess the transient response
(response to setpoint changes or response to interference) of the speed controller within the time range. The test signal is connected to the speed controller
output for recording of the response to interference.
Measuring
parameters for
setpoint and
interference
variable step
changes
Amplitude
This parameter determines the magnitude of the set setpoint or interference
step change
Measuring time
This parameter determines the recorded period (up to 2048 x speed controller
cycles).
Offset
A small offset of a few motor revolutions per minute may be set to eliminate the
influence of adhesive friction.
10
S The offset is started up via an acceleration ramp.
S The acceleration value is defined for an axis/spindle:
Axis:
Spindle:
MD 32300: MAX_AX_ACCEL
MD 35200: GEAR_STEP_SPEEDCTRL_ACCEL
MD 35210: GEAR_STEP_POSCTRL_ACCEL
Where:
Acceleration value = 0, no ramp
Acceleration value > 0, ramp active
S The actual measuring function is not activated until the offset value is
reached.
Settling time
Recording of the measured data and outputting of the test setpoint start after a
delay equal to this value after the offset is activated.
10-186
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.4 Frequency response measurement
03/2006
Speed setpoint
Amplitude
Offset
Time
Settling time
0
Position
characteristic
Measuring duration
Time
0
Fig. 10-3
Additional
information
Setpoint signal for the speed control loop – step response measuring function.
The measuring parameters and measurement results (diagrams) can be loaded
or saved using the File functions soft key.
10
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-187
03/2006
10 Drive Optimization
10.4 Frequency response measurement
10.4.3
Scanning position control loop
Functionality
The behavior when transferring to the active position measuring system is
always analyzed. The NCK generates an error message if the function is activated for a spindle without position measuring system. Various lists of measuring
parameters are offered depending on which basic setting is selected.
Procedure
1. Setting the traveling range monitoring and the enabling logic on the
main screen.
One of three different types of measurement can be selected:
S Reference frequency response
S Setpoint step change
S Setpoint ramp
2. Setting the necessary parameters on the measuring parameters screen
3. Displaying the measurement result on screen using the Display soft key
10
Fig. 10-4
Reference
frequency
response
Display diagram: Example of a position control loop
The reference frequency response measurement determines the transmission
response of the position controller in the frequency range (active position measuring system). The parameters for the setpoint filters, Kv value and bias control
should be set to ensure there is as little resonance as possible throughout the
frequency range. In the case of dips in the frequency response, the setting of
the feedforward control balancing filters should be checked. Excessive resonance requires
1. Decrease in KV value
2. Canceling the bias control value
3. Use of setpoint filters
The effects of these measures can also be checked in the time range.
10-188
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.4 Frequency response measurement
03/2006
Measuring
parameters for
reference
frequency
response
Amplitude
This parameter determines the test signal amplitude. It should be set to the
smallest possible value (e.g. 0.01 mm).
Offset
The measurement requires a low speed offset of just a few motor revolutions
per minute. The offset must be chosen so that the speed does not pass through
zero at all at the set amplitude.
Bandwidth
Setting for the analyzed frequency range (no more than half the position controller scanning frequency). The lower this value, the finer the frequency resolution
and the longer the measurement time. The maximum value corresponds to half
the position controller sampling rate (e.g. 200 kHz with position controller sampling time of 2.5 ms).
Averaging
This value increases both the accuracy of the measurement and the measuring
duration. A value of 20 is normally suitable.
Settling time
Recording of the measured data starts after a delay equal to the value set here
after the offset and test setpoint are activated. A value of between 0.2 and 1 s is
recommended. Do not set too low a value for the settling times or the frequency
response and phase diagrams will be distorted.
Setpoint step
change and
setpoint ramp
Initiation of the step change and the ramp can be used to assess the transient
response or positioning response of the position control within the time range,
particularly the effect of setpoint filters. If an offset value other than zero is input,
the step change is stimulated during traversal. For the sake of clarity, the displayed position actual value does not include this speed offset. The following
measured variables are possible:
S Actual position value (active position measuring system)
S Control deviation (following error)
Measuring
parameters for
setpoint step
change and ramp
Amplitude
This parameter determines the magnitude of the set setpoint step change or
ramp.
Offset
The step change is initiated from the stopped state or starting from the constant
traveling speed set with this parameter.
Measuring time
This parameter determines the recorded period (up to 2048 x position controller
cycles).
Settling time
Recording of the measured data and outputting of the test setpoint start after a
delay equal to this value after the offset is activated.
Ramp time
For the Setpoint ramp basic setting, the position setpoint is set according to the
set ramp duration. In this case, the acceleration limits which currently apply to
the axis or spindle are effective.
A jerking motion can be set using the axis-specific NC-MD 32410
AX_JERK_TIME (if NC-MD 32400 AX_JERK_ENABLE is set to 1).
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-189
10
03/2006
10 Drive Optimization
10.4 Frequency response measurement
The position setpoint and the actual value of the active measuring system are
recorded.
Position
Amplitude
t
0
Settling time
Ramp
time
Measuring duration
Speed
Offset
t
0
Fig. 10-5
Signal curve for the position setpoint/ramp measuring function
At maximum axis velocity, there is a (virtual) step change in the velocity (continuous line).
10
The curves represented by the dashed line correspond to a realistic, finite
value. The offset part is calculated from the displayed graph in order to highlight
the transition processes.
Step height
To avoid damaging the machine, the step height for the setpoint step change is
limited to the value specified in MD 32000 MAX_AX_VELO. As a result, the
desired step height may not be reached.
The MD 32000 MAX_AX_VELO and MD 32300 MAX_AX_ACCEL have a similar effect for the setpoint ramp in the ramp area.
The MD 32000 MAX_AX_VELO limits the ramp inclination (speed limit), whereby the drive does not reach the programmed amplitude.
The restriction in acceleration caused by the MD 32300 MAX_AX_ACCEL
“smoothes” the transition at the start and end of the ramp.
!
10-190
Danger
Do not make changes to the MD 32000 MAX_AX_VELO and MD 32300
MAX_AX_ACCEL (e.g. to achieve a certain pitch) without carefully considering
the consequences. These have been matched exactly to the machine!
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.5 Measuring function for coupled axes
03/2006
10.5
Measuring function for coupled axes
Functionality
Composite axes were not supported by the previous “Measuring function” and
“Function generator” start-up aids. With version 5 of the software package, the
existing HMI user interface has been upgraded:
it is now possible to easily optimize by scanning individual axes. This is done by
setting certain “measuring parameters”.
The upgraded HMI user interface allows the start-up engineer to scan each
individual axis
S of the Composite gantry
S the coupled master and slaves (from software version 6.4)
S and mixed master–slave combinations coupled to gantry axes (from software version 6.4 )
with due regard to the permitted measuring parameters.
The HMI programs the axes with the same values so that they perform identical
movements.
The user can record the results for one or 2 axes at the same time. This corresponds to the previous measuring function for 2 independent axes. With mixed
coupled units, the leading axis always taken from the gantry composite axis. All
further axes are then synchronizing axes with the same parameters.
Start-up functions
The HMI user interface provides further measuring functions as aids to start-up.
Soft keys can be used to determine whether a certain axis configuration should
be used for scanning in the
S Power control loop
S Speed control loop
S Position control loop
10.5.1
Interconnected gantry axes only or master–slave couplings
Parameter settings
The Function generator and Measure start-up functions are still programmed via
PI services. The traversing motion is started for all programmed axes by pressing the MSTT button NC-Start in JOG operating mode.
On the “Function generator in interconnected gantry” screen, the user interface
displays an image in which you can enter 2 amplitude values and a period duration, pulse width, offset and limitation.
On the “Measuring function in interconnected gantry” screen, in addition to the
2 amplitude values, you can enter a bandwidth, averaging, settling time and an
offset. The first amplitude value applies to the measured access and the second
to the other, coupled axes.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-191
10
03/2006
10 Drive Optimization
10.5 Measuring function for coupled axes
Measuring
parameters in the
speed control loop
In the reference frequency response for the speed control loop, actual and setpoint speed values may be entered as the following measuring parameters for
both interconnected gantry/axes and master/slave couplings.
Amplitude of leading axis
or master axis
This parameter determines the magnitude of the test signal amplitude for the
gantry leading or guiding axis or master axis in mm/min. On the motor side, this
should cause a slow speed of just a few (approx. 1 to 2) rpm.
Amplitude of synchronizing axis(es)
or slave axis(es)
Edited measured variables for the amplitude of the gantry synchronizing
axis(es) or slave axis(es) in mm/min.
Bandwidth
Analyzed frequency range
4.0 kHz for 840D (scanning frequency 8.0 kHz).
Averaging
This value increases both the accuracy of the measurement and the measuring
duration. A value of 20 is normally suitable.
Settling time
Recording of the measured data starts after a delay equal to the value set here
after activation of the test setpoint. A value of between 0.2 and 1 s is recommended.
Offset
The offset is started up via an acceleration ramp.
The acceleration value is defined for an
Axis:
MD 32300: MAX_AX_ACCEL
Spindle:
MD 35200: GEAR_STEP_SPEEDCTRL_ACCEL
MD 35210: GEAR_STEP_POSCTRL_ACCEL
Where:
Acceleration value = 0, no ramp
Acceleration value > 0, ramp active
10
The actual measuring function is not activated until the offset value is reached.
Example of a pure
master–slave
coupling
Speed control loop: All the axes are on a 1-axis module.
Axis X1
(1) Master axis
Axis Z1
(3) Slave axis
Axis A1
(4) Slave axis
Axis
(7) Slave axis
In a pure coupling mode, the displayed texts change if a different coupling mode
was previously active. The structure of the entire user interface does not
change. An axis is displayed as a master axis and all the other axes are then
the slave axes.
!
Important
Only the coupling axes for the selected axis are displayed.
If there are two axes on a double-axis module, neither the gantry nor the
master/slave are displayed in a pure coupling mode.
It should be noted that only one measuring function can ever be started per
module.
10-192
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.5 Measuring function for coupled axes
03/2006
Scanning in the
position control
loop
!
If a scan is carried out in the position control loop, only gantry axes are included. None of the master/slave axes involved have a PI service, so are not initiated on the NC side.
Caution
If two measuring functions are detected on a module, the coupling is cleared
internally and only one 1 PI service is sent to the selected axis. Particular
caution is required since another axis may also be used internally.
Amplitude of leading axis
This parameter determines the magnitude of the test signal amplitude of the
gantry leading axis in mm. It should be as small as possible (e.g. 0.01 mm).
Amplitude of synchronizing axis(es)
Edited measured variables for the amplitude of the gantry synchronizing
axis(es) in mm/min.
Bandwidth
Setting for the analyzed frequency range (no more than half the position controller scanning frequency). The lower this value, the finer the frequency resolution
and the longer the measurement time. The maximum value corresponds to half
the position controller sampling rate (e.g. 200 kHz with position controller sampling time of 2.5 ms).
Averaging:
This value increases both the accuracy of the measurement and the measuring
duration. A value of 20 is normally suitable.
Settling time
Recording of the measured data starts after a delay equal to the value set here
after activation of the offset and test setpoint. A value of between 0.2 and 1 s is
recommended. Do not set too low a value for the settling times or the frequency
response and phase diagrams will be distorted.
Offset
The measurement requires a low speed offset of just a few motor revolutions
per minute. The offset must be chosen so that the speed does not pass through
zero at all at the set amplitude.
10.5.2
Mixed couplings of master/slave and gantry axes
As with pure interconnected gantry axes or master/slave couplings, only two
axes may be selected for scanning. If more than two axes are selected, a message appears when the scan starts.
Example in the
speed control loop
Gantry axis X1 is coupled to master axis A1. The gantry synchronizing axis Z1
is in turn coupled to a slave axis.
Axis X1
Axis Z1
Axis A1
Axis
(1) Gantry leading axis (this is always a gantry axis)
(3) Gantry synchronizing axis
(4) Master axis
(7) Slave axis
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-193
10
03/2006
10 Drive Optimization
10.6 Graphical display
All the axes are on a 1-axis module. All the axes of the interconnected coupling
are displayed. No more than one leading axis and two synchronizing axes are
ever visible. Nevertheless, all the axes can be used for navigation.
10.6
Graphical display
Explanation
The graph is displayed by pressing the Display soft key in the main screen for
the measuring function.
10
Fig. 10-6
Display diagrams 1 and 2 of speed control loop
X marker and
Y marker On/Off
soft keys
These soft keys are used to display a vertical or horizontal line representing the
abscissa or ordinate in the selected diagram. The associated coordinates are
also output. The soft key X marker or Y marker must be selected again in order
to deselect the markers. The markers are moved by means of the cursor keys.
2nd marker X and
2nd marker
Y zoom and full
screen soft keys
A 2nd X marker or 2nd Y marker may be overlaid in order to highlight differences. The absolute position of the selected cursor and the delta values between
the relevant cursor lines are thus highlighted.
The “Zoom” soft key can be used to gradually increase the area between the
cursors. Use the Select button to change cursor.
The “Full screen” soft key is used to return to the optimum representation.
Scale...
10-194
Scaling is normally automatic. The Scale soft key can also be used to manually
set the scaling for the individual traces.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.6 Graphical display
03/2006
X marker and
Y marker Y zoom
and full screen
soft keys
These soft keys are used to display a vertical or horizontal line representing the
abscissa or ordinate in the selected diagram. The associated coordinates are
also output. The soft key X marker or Y marker must be selected again in order
to deselect the markers. The markers are moved by means of the cursor keys.
Graph...
This soft key is used to toggle between the individual representations and the
double graph. You can then use the “Print graph” soft key to store the graph
(Print to file) or output it at the selected printer.
Trace...
Individual traces can be displayed and hidden in graph 1 and graph 2. The soft
key always takes effect in the currently selected window.
Start
The “Start” soft key is used to start a new measurement.
10.6.1
Associated conditions for gantry axes
From software
version 5.1
SIMODRIVE 611 digital drives: Only one function generator or one measuring
function can be activated on a multiple module, which means that the new functionality is available if the gantry axes are on different modules.
Reference material:
/FB3/ G1, Description of the special functions
Gantry axes
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10
10-195
03/2006
10 Drive Optimization
10.7 Trace function
10.7
Trace function
A trace represents monitored values and signals over a given time interval.
Servo trace provides functions with a graphical user interface for checking and
monitoring drive/servo signals and statuses.
Function
overview
The trace function offers the following features:
S 4 trace buffers with up to 2048 values each.
S Choice of SERVO, safety integrate and 611D signals (in position control
cycles)
S Trace and trigger signals can be set through absolute addresses and value
masking.
S Different trigger conditions for starting the recording.
Triggering always on trace 1.
S Both pre- and post-triggering.
S Measuring signal display
S Fixed Y scaling can be selected for each trace or automatic scaling
S Marker function can be selected in order to delimit areas of detail for each
trace. Expand function on the time axis (Zoom X).
S Selectively loads and saves the measuring parameters and traces
10
S Up to 10 signal tracks per trace for bit-coded signals from Safety Integrated
S Options for modifying the trace display and print-out.
Note
The trace function can only be used with HMI Advanced or the Start-up tool. It
is possible to represent bit-coded signals from Safety Integrated on ten tracks
over the measuring interval for HMI Advanced from software version 6.2.
10-196
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.7 Trace function
03/2006
Measurements:
NC
Measuring
buffer
– Parameter
settings
Files
– Activating
See 10.7.2
File functions
Display buffer
see 10.8.5
Display functions, see 10.7.3, 10.8.4
Backup
.INI
See 10.8.6
Display
Fig. 10-7
Printer
Overview of the function groups
The measuring signals are selected and the measuring parameters are set
using soft keys and drop-down lists. Operation is either via mouse or via
keyboard.
10
Operation
The cursor is controlled
using the arrow keys on the
front of the operating panel
or with the mouse.
Select button
To access the lists, place
the cursor on a list box and
press the insert key.
The list drops
down.
You can scroll down
by using the arrow
keys.
Activate the input
key to select
the desired item.
Fig. 10-8
Cursor operation
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-197
03/2006
10 Drive Optimization
10.7 Trace function
10.7.1
Main screen
Main screen
Servo trace
The main screen for the trace function is accessed using the
Drives/Servo \ Servo trace soft keys.
10
Fig. 10-9
10.7.2
Basic servo trace screen
Programming and activating measurements
Programming
on the main screen
The main screen is used to select
S The axis/spindle to be measured
S The signal to be measured
S The measuring duration
S Trigger time
S Trigger type
S Trigger threshold
Signal selection
Input box
Axis/spindle name
10-198
The cursor must be positioned on the “Axis/spindle name” list box for the trace
concerned. The selection is then made by using the Axis+ and Axis– soft keys
or by activating the desired item in the drop-down list box.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.7 Trace function
03/2006
Signal selection
input box
The cursor must be positioned on the “Signal selection” list box for the trace
concerned. Then activate the desired items by selecting them from the list box.
The options available for selection depend on the configuration and on which
functions are activated.
Measuring
parameters
Measuring duration
input box
Trigger time input
box
The measuring time is entered directly in the “Measuring duration” input box.
Direct input of pre- and post-triggering. With negative input values (leading sign
minus –) recording begins at the set time before the trigger event.
With positive input values (without leading sign) recording begins after the
trigger event.
Associated condition: Trigger time + measuring duration y 0.
Trigger input box
The trigger type is selected from the “Trigger” drop-down list. The trigger always
relates to trace 1. Once the trigger condition has been fulfilled, traces 2 to 4 are
started at the same time.
Settable trigger conditions:
S No trigger, i.e. measurement begins when the Start soft key is activated
(all traces are started time-synchronized).
S Positive edge
S Negative edge
S Trigger event from the sub-program
Threshold input box
10
Used to enter the trigger threshold directly.
The threshold is only effective with trigger types “Positive edge” and “Negative
edge”.
The unit refers to the selected signal.
Soft keys
Axis +
Axis –
Used to select the axis/spindle when the cursor is on the relevant “Axis/spindle
name” list box.
Start and Stop
soft keys
To start the trace function recording, press the Start soft key. The current message is aborted by activating the Stop soft key or RESET.
You can also select the axis/spindle by using the cursor in the drop-down list.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-199
03/2006
10 Drive Optimization
10.7 Trace function
Physical address
soft key
The entries are made in the servo trace function basic screen.
S The “Physical address” signal type must be selected in the desired trace.
S The cursor in the desired trace must be positioned in the associated signal
selection box (on Physical address).
The physical address dialog box is overlaid when you activate the Physical
address soft key.
Note
This function is only required in special cases when the information from the
usual signals (see “Signal selection” list field) is insufficient. Please contact the
SIMODRIVE hotline to discuss how to proceed.
10
Fig. 10-10 Input screen for setting the physical address parameters.
All parameters settings are entered in hexadecimal format.
Segment address
input box
Direct input of the segment address of the signal to be logged.
Offset address input
box
Direct input of the offset address of the signal to be logged.
Mask input box
If you want to display certain bits only, select them in this dialog box.
Threshold input box
In the “Threshold” input box, you can only set the trigger threshold for the physical address of trace 1. If you exit the input box by activating the OK soft key, this
hexadecimal value is entered in the “Threshold” field of the servo trace basic
display.
10-200
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.7 Trace function
03/2006
Start of
measurement
Once the parameters have been set, start the measurement by pressing the
Start soft key. Execution is dependent on the condition specified in the
Measuring parameters and “Trigger” input box.
Terminating the
measurement
Measurement is terminated after the time specified in the Measuring parameters/“Measuring time” input box has expired or was interrupted by pressing the
Stop soft key.
Results of a canceled measurement cannot be displayed (soft key display).
The end of the measurement is signaled to the user with a suitable message in
the dialog line.
General
If the user has carried out measurements with values/signals, these are stored
in the measured value buffer and remain valid until they are replaced by measured value files using the file functions or by the measured values supplied when
a measurement was restarted by the NCK.
10
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-201
03/2006
10 Drive Optimization
10.7 Trace function
10.7.3
Display function
When the measurement is complete, the result can be displayed in a graph.
The horizontal soft key Display calls up the screen (Fig. 10-11).
The measured traces are shown as diagrams.
Graph1 shows trace 1 green and trace 2 (blue), while graph2 contains trace 3
green and trace 4 (blue).
10
Fig. 10-11 Graph1 and graph2 each shown with 2 traces
X marker and
Y marker soft keys
The X/Y markers are activated or deactivated in the active graph. The corresponding position value is shown in the graph. The markers are moved by
means of the cursor keys.
Full screen
soft key
After the zoom function has been used (see below), this soft key returns to the
original display as shown in Fig. 10-11.
Soft key Scale...
When you press the soft key, Fig. 10-12, Y axis scaling, appears. You can scale
the traces in this window.
10-202
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.7 Trace function
03/2006
Fig. 10-12 Scaling of Graph1 and Graph2
Vert. SK for scale...
The scaling options include automatic scaling and fixed scaling (Select button)
for the Y axis for each trace channel:
auto
Automatically determines the minimum and maximum values from the
measured values
Y Min, Y Max boxes
If auto is selected, these display the limit values originating from the measurement.
fixed
The user selects the minimum and maximum values for the trace channel himself.
Y Min, Y Max input boxes
May be set to fixed values set by the user.
The entries are only transferred to the graph when you exit the screen form if
“fixed” is set in the scaling field.
For the markers, it can be specified that they should move at the same time in
both graphs (“Couple with graph 1” set for graph 2) or that each graph has separate markers.
The image can be exited using the vertical soft keys “Graph1...” or “Graph2...” or
“Graph 1 + Graph 2...”.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-203
10
03/2006
10 Drive Optimization
10.7 Trace function
Graph ... soft key
The vertical Graph ... soft key in Fig. 10-11 leads to a submenu containing the
following functions:
–
Bit selection, see 10.7.4
–
Graph 1, 2 selection for enlarged view
–
Print graph, see also 10.7.6
–
Printer selection (real printer or bitmap file in the dh\dg.dir\bitmap.dir
directory).
The following menu appears:
10
Fig. 10-13 Graph ...menu
Soft key Trace 1+2
Trace 3+4
The Trace 1+2 ... soft key is used to select an individual trace from the graph
with the focus for more detailed examination.
Press once to focus on trace 1 alone in graph 1.
Press twice to focus on trace 2 alone in graph 1.
Press three times to focus on trace 1 + 2 together in graph 1.
If the focus is on graph 2, the soft key is labeled Trace 3+4 ... It is used in the
same way for trace 3 and trace 4.
Switch between
graph 1 and 2
The active graph out of 2 traces is highlighted (focus). Press CTRL-TAB to activate the other graph.
Zoom on time axis
The operations described above included the setting of a marker. Once an
X marker has been set, the third vertical soft key offers the option of setting a
2nd X marker. This is used to define a time interval from the trace. The third
vertical soft key then has the label “Zoom X”.
10-204
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.7 Trace function
03/2006
When you press this soft key, the area between the two X markers is extended
over the time axis so that it fills the entire available area of the display. This
allows signal curves to be monitored in more detail.
Zoom in Zoom
Further markers can be set in the extended image and, once another time interval has been specified, to zoom using 2 X markers.
Move measurement curves
10.7.4
If measured value curves (trace1, trace 2 or trace 3, trace 4) coincide in the display, making them difficult to evaluate, the activated trace can be moved to a
suitable position using Cursor Up or Cursor Down.
Display bit graph for SI signals
Function
10 tracks from 10 signal bits from Safety Integrated can be displayed in graphs
over the measurement period. They are triggered and measured as described
in the previous sections.
Procedure
S Selection of the signals
10
S Assignment of signal bits to tracks
S Signals displayed as bit graphs
Requirement
If Signal selection was used to select a bit-coded SI signal, there is a vertical
soft key called “Bit selection trace i” for the corresponding trace.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-205
03/2006
10 Drive Optimization
10.7 Trace function
Fig. 10-14 Selected bit-coded SI signals
10
Bit selection
Trace i
When you press this soft key, a screen appears in which you can assign the
individual signal bits to display tracks.
Fig. 10-15 Assigning signals to tracks (example of trace 1)
10-206
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.7 Trace function
03/2006
Procedure
For every non-free/reserved bit of the signal, you can enter a track number 0 – 9
corresponding to tracks 0 – 9 in the allocated input box. The “Track number:”
line indicates which of the tracks are already assigned and which are still free.
Scroll vertically to display bits > 25.
The file HMI_ADV\IBSVTSI.INI contains starting values for the allocation which
can be modified in the screen shown in Fig. 10-15.
Accept soft key
The current assignment is transferred to the HMI_ADV\IBSVTSI.INI file and is
suggested again the next time the signal is selected.
Cancel soft key
Used to exit the screen without transferring the changes to the
HMI_ADV\IBSVTSI.INI file.
Mix traces
From a maximum of 4 individual traces, the bit traces of which were assigned as
described above, you can select up to 10 traces and display them together in
an image for comparison purposes.
When evaluating traces and trace mixes, always make sure that the measured
values under consideration are from the same trigger event and take over the
same measuring duration. See also subsection 10.7.5.
Mix traces soft key
The soft key can be accessed from Fig. 10-14. This gives the following screen:
10
Fig. 10-16 Compiling a trace mix
The top part of the screen shows how the traces are currently assigned in the
joint trace mix.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-207
03/2006
10 Drive Optimization
10.7 Trace function
In the Bit selection part of the screen, select the relevant bit identifier from the
drop-down menu for each of the traces, the signals from which are to be transferred to the trace mix and, in the “Track selection:” input box, enter the desired
track from the trace mix or select it from the drop-down list.
Delete
track soft key
The selected signal no longer belongs to the trace mix.
Delete
all soft key
All assignments of signals to tracks in the trace mix are deleted.
Cancel soft key
Used to exit the screen without transferring the changes to the
HMI_ADV\IBSVTSI.INI file.
Accept soft key
The current assignment is transferred to the HMI_ADV\IBSVTSI.INI file and is
suggested again the next time the trace mix is selected.
10
10-208
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.7 Trace function
03/2006
Display
bit graph ...
soft key
The soft key can be accessed from Fig. 10-14. This gives the following screen:
Fig. 10-17 Bit graph – example of trace 1
The signals from up to 10 tracks are represented over the duration of the measuring interval. Vertical soft keys can be used to change the view as required or
to print out the bit graph.
Hide
identifiers
soft key
Shows/hides the signal identifiers overlaid over the signal curve. The function is
also available in the extended view. See the “Zoom X” soft key.
Colors soft key
Opens a submenu from which you can select:
S User
S VGA
S VGA positive
S Monochrome
S Monochrome positive
under “Color scheme”, The color palette corresponding to your selection is displayed. You can then select different colors for each track.
There is a common color available for all signal identifiers.
Procedure:
1. Use Cursor Up/Down Track/Word select “Identifier”, palette receives focus
2. Use Cursor Up/Down/Right/Left select color
3. Select Input/Return to accept.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-209
10
03/2006
10 Drive Optimization
10.7 Trace function
Vertical soft keys under Color settings:
Save:
Current color settings are accepted without exiting
the screen.
Cancel:
Exits the screen without saving the changes to the color
settings.
OK
Accepts the current color settings and exits the screen
Click on Cancel or OK to return. The 10-track view of the trace is displayed
once more, as shown in Fig. 10-17.
X marker soft key
A vertical marker is added to the bit graph. It can be moved along the time axis
using Cursor Left/Right, e.g. to the start of an “interesting” signal occurrence.
The time at the marker position and the measured value interpreted as a number is displayed in the header over track 0.
The soft key is used to toggle between On and Off. If X marker Off is activated,
then the marker is deleted once more,
2nd X marker
soft key
A second vertical marker of a different color is added to the bit graph. It can be
moved along the time axis using Cursor Left/Right, e.g. to the end of an
“interesting” signal occurrence. The soft key is used to toggle and switches to
the other market if pressed again.
If 2 markers are used to describe a time interval, the size is displayed as delta t:
...ms in the footer. The 4th vertical soft key switches to “Zoom X”.
10
Zoom X soft key
The interval between the markers is extended to the full width of the available
display area. The “X marker On” soft key is available once more in the zoomed
image. This allows another marker to be set in the extended view.
The “Zoom X” soft key has the same effect as for trace mix.
Full screen
soft key
This soft key is used to return from a zoomed view to the original view of the
signal curve.
Trace 1 ... soft key
The 7th vertical soft key is used to switch from trace 1 to trace 4 and Trace Mix
one after the other.
Print bit graph
soft key
The function works in the same way as “Print graph” for bit graphs. See also
subsection 10.7.6.
10-210
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.7 Trace function
03/2006
User
bit names
For Safety Integrated, the signals with fixed bit names are supplemented with
the following signals, whose names can be defined/redefined by the user:
Table 10-2
SI signals with variable bit identifiers
SI signal German
Bit
Identifier English
ext. NCK–SPL interface inputs
0..31
EXT_NCK_SPL_INPUT_0
...
EXT_NCK_SPL_INPUT_31
32..63
EXT_NCK_SPL_INPUT_32
...
EXT_NCK_SPL_INPUT_63
0..31
EXT_NCK_SPL_OUTPUT_0
...
EXT_NCK_SPL_OUTPUT_31
32..63
EXT_NCK_SPL_OUTPUT_32
...
EXT_NCK_SPL_OUTPUT_63
0..31
INT_NCK_SPL_INPUT_0
...
INT_NCK_SPL_INPUT_31
32..63
INT_NCK_SPL_INPUT_32
...
INT_NCK_SPL_INPUT_63
0..31
INT_NCK_SPL_OUTPUT_0
...
INT_NCK_SPL_OUTPUT_31
32..63
INT_NCK_SPL_OUTPUT_32
...
INT_NCK_SPL_OUTPUT_63
0..31
EXT_PLC_SPL_INPUT_0
...
EXT_PLC_SPL_INPUT_31
32..63
EXT_PLC_SPL_INPUT_32
...
EXT_PLC_SPL_INPUT_63
0..31
EXT_PLC_SPL_OUTPUT_0
...
EXT_PLC_SPL_OUTPUT_31
32..63
EXT_PLC_SPL_OUTPUT_32
...
EXT_PLC_SPL_OUTPUT_63
0..31
INT_PLC_SPL_INPUT_0
...
INT_PLC_SPL_INPUT_31
32..63
INT_PLC_SPL_INPUT_32
...
INT_PLC_SPL_INPUT_63
0..31
INT_PLC_SPL_OUTPUT_0
...
INT_PLC_SPL_OUTPUT_31
32..63
INT_PLC_SPL_OUTPUT_32
...
INT_PLC_SPL_OUTPUT_63
ext. NCK–SPL interface outputs
int. NCK–SPL interface inputs
int. NCK–SPL interface outputs
ext. PLC–SPL interface inputs
ext. PLC–SPL interface outputs
int. PLC–SPL interface inputs
int.PLC–SPL interface outputs
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-211
10
03/2006
10 Drive Optimization
10.7 Trace function
Table 10-2
SI signals with variable bit identifiers
SI signal German
Bit
Identifier English
NCK–SPL marker
0..31
NCK_SPL_MARKER_0
...
NCK_SPL_MARKER_31
32..63
NCK_SPL_MARKER_0
...
NCK_SPL_MARKER_31
0..31
PLC_SPL_MARKER_0
...
PLC_SPL_MARKER_31
32..63
PLC_SPL_MARKER_32
...
PLC_SPL_MARKER_63
PLC–SPL marker
Operation
When a trace log for signals from the above table is loaded, you can use:
Display/Graph/<Trace i>
A screen with the selected signal and its bits is displayed, with track assignment
if appropriate. For example:
10
Fig. 10-18 Name changed for bit 54
Vertical soft keys
Change names
Use the cursor keys to move to the signal identifiers to be changed and enter a
new identifier. Press the Input button to confirm.
10-212
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.7 Trace function
03/2006
Undo change
The identifier changes are canceled.
Accept
The changed identifiers are transferred to the HMI_ADV\IBSVTSI.INI file and
are then displayed once more in connection with this trace.
Cancel
Exits the screen without saving the changes to the identifiers.
10.7.5
File functions
Description
The File functions soft key is used to switch to the “File functions” screen.
Here you can save/load/delete the measurement settings and measured values
for the trace function.
The file functions are not intended to be a substitute for making a copy of all
system and user data, e.g. for archiving or series start-up purposes.
10
Fig. 10-19 Servo trace file function
Naming files
You can select an existing file from the drop-down list in the “File” field, or enter
one in the text box below.
Selecting the
directory
In the “Directory” field, you select the directory in which the file is to be saved.
This may be a directory you created yourself under “Services” or the main data
storage directory (list entry: Default directory).
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-213
03/2006
10 Drive Optimization
10.7 Trace function
Selecting data type
In the “Data” field, you select the files to be stored. Only one data type can be
selected at once. Use the cursor keys for selecting the data type and enable
using the toggle key.
Vertical soft keys
Delete
The selected file with measured values and parameters is deleted.
Save
The displayed measured values and the parameters used for the measurement
are saved to the set file. They are then available to display, prepare (e.g. Zoom)
and print out using the “Load” function.
Load
A file that was previously saved with the “Save” soft key is fetched to the display
buffer and then displayed when the “Display” horizontal soft key is pressed.
The file names of any traces displayed in the header are shown once the display has been created from a file.
A submenu asks whether the existing display buffer should be replaced.
10
Creating
subdirectories
–
If you select “Cancel”, nothing is loaded. This means that the existing
measurement can be saved using the “Save” soft key before a new file is
loaded.
–
Use “Replace” to accept measured values and parameters from the file
as the current trace data. Measured data from the last measurement will
be lost if it is not first saved to a file using “Save”.
New subdirectories are created in the “Services” area.
You can create a subdirectory there in “Manage data” mode in the “Diagnostics”
directory.
See also:
Reference material:
10-214
/BAD/ User Guide for HMI Advanced,
Section: Services area
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.7 Trace function
03/2006
10.7.6
Print graph
Printer settingsThe printer selection screen is called up by pressing the
HMI\Printer selection soft keys (Fig. 10-20).
Use the toggle key to select whether the displayed graphics are to be sent directly to the printer by activating the Print graphs soft key, or output it in a bitmap file instead.
10
Fig. 10-20 Basic screen for printer selection
Output directly to
printer
The printer must be set up under MS WINDOWS.
Output as
bitmap file
If you want to save the graph to a bitmap file (*.bmp), proceed as follows:
You can set “Print” in the printing options.
Upon activation of the Print graphs soft key in the “Display” screen, the displayed graphics are printed on the active printer.
Set “Output as bitmap file” in the selection field for the printer setting.
When you press the Print graph soft key on the “Display” screen, the screen for
entering a file name appears (Fig. 10-21). Enter a new name in the drop-down
list or select an existing file name for overwriting.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-215
03/2006
10 Drive Optimization
10.8 Analog output (DAC)
Fig. 10-21 File name box for bitmap output
Naming files
You can select an existing file from the drop-down list in the “File name” field, or
enter one in the text box below.
Selecting the
directory
In the “Directory” field, you select the directory in which the file is to be saved.
This may be a directory you created yourself under “Services” or the main data
storage directory (list entry: Default directory).
Activate the OK soft key to save the file.
10
Return to the current graphics screen by activating the Abort soft key.
10.8
Analog output (DAC)
Note
The DAU function is described in:
Reference material
10-216
/FBA/ DD1, Description of the drive functions,
Diagnostic functions
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.9 Automatic controller settings ( HMI Advanced only)
03/2006
10.9
Automatic controller settings ( HMI Advanced only)
Functionality
Functions for automatic speed controller adjustment:
S Three variants for determining the gain and reset time.
S Independent determination of any required current filters (max. three
bandstop filters).
S Displaying the measured or calculated frequency responses, as for the
measuring functions.
Note
Where the table has a very low natural resonant frequency (< 20 Hz), the reset
time should be checked manually. The reset time setting may be too low.
Procedure
In the “Start-up” area, select the “Drives/servo” soft key.
a) Normal case
In the extended menu, press the “Aut. ctrl setting” soft key. The main “Automatic
controller setting” display appears.
Aut. ctrl
setting
10
Fig. 10-22 Main “Automatic controller setting” display
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-217
10 Drive Optimization
10.9 Automatic controller settings ( HMI Advanced only)
03/2006
The input in the “Drive test enable travel” and “Traveling range” window areas
has the same significance as for the measuring functions.
The setting type is defined in the “Mode” function area.
1. Select the type of setting from the “Operating mode” function area.
“Variant 1” off.
2. Press the “Start” soft key.
3. Follow the instructions in the menu-driven dialog (see the gray boxes in the
flowchart below).
4. Press the “OK” soft key when requested to do so.
5. Press the “NC Start” soft key when requested to do so.
Warning: With NC Start, the axis performs a traversing motion.
To optimize further axes, select the axes with the “Axis+” or “Axis–” soft key and
repeat the procedure from step 1.
b) Special case:
Modify parameters
You can use the controller settings integrated into the control to
S change the parameter settings,
S start,
S display and
S store the settings of the integrated controller.
The setting type is defined in the “Mode” function area. Three different variants
are available:
10
S Variant 1: Default setting
S Variant 2: Setting with critical dynamic response
S Variant 3: Setting with good damping
Vertical soft keys
“Axis+” soft key:
Selects the next axis to be optimized.
Soft key “Axis–”:
Selects the previous axis to be optimized.
Soft key “Direct selection”:
Selects the axis to be optimized directly in a dialog window.
Soft key “Start”:
Starts the automatic controller setting for the selected axis.
Soft key “Stop”:
Stops the automatic controller setting for the affected axis (if a measuring
function is active).
10-218
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.9 Automatic controller settings ( HMI Advanced only)
03/2006
10.9.1
Flowchart for self-optimization
The self-optimization can be terminated at any time by pressing the “Abort” soft
key.
SK “Start”
Load current
drive MD and
write default
values
Start
mech. system
measurement
part 1?
SK “Parameter”
Enter the
measuring
parameters
SK “Abort”
(discard
changes)
SK “OK”
(accept
values)
10
SK “OK”
Prompt to press NC-Start
Warning:
Pressing NC-Start causes the axis
to perform a traversing motion.
1
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-219
03/2006
10 Drive Optimization
10.9 Automatic controller settings ( HMI Advanced only)
1
Start
mech. system
measurement
part 2?
SK “Parameter”
Enter the
measuring
parameters
SK “Abort”
(discard
changes)
SK “OK”
(accept
values)
SK “OK”
Prompt to press NC-Start
Warning:
Pressing NC-Start causes the axis
to perform a traversing motion.
10
Start
current control loop
measurement?
SK “Parameter”
Enter the
measuring
parameters
SK “Abort”
(discard
changes)
SK “OK”
(accept
values)
SK “OK”
Prompt to press NC-Start
Warning:
Pressing NC-Start operates the
axis controlled by the current.
2
10-220
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.9 Automatic controller settings ( HMI Advanced only)
03/2006
2
SK “Parameter
Kp setting”
Enter
parameters for
determination of
optimum
gain
SK “Parameter
Tn setting”
Enter
parameters for
determination of
optimum
reset time
Start calculation of
controller
data?
SK “Abort”
(discard
changes)
SK “OK”
(accept
values)
SK “Abort”
(discard
changes)
SK “OK”
(accept
values)
SK “OK”
10
Please wait....
Contr. data are
being computed
3
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-221
03/2006
10 Drive Optimization
10.9 Automatic controller settings ( HMI Advanced only)
3
3
Do you want to back up the
boot file for drive X and
display the modified
controller data?
SK “No”
Boot file is not
saved
SK “Yes”
Boot file is
saved
10
Start
measurement of
speed controller?
SK “Parameter”
Enter the
measuring
parameters
SK “Abort”
(discard
changes)
SK “OK”
(accept
values)
SK “OK”
Prompt to press NC-Start
Warning:
Pressing NC-Start causes the axis
to perform a traversing motion.
End
10-222
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10 Drive Optimization
10.9 Automatic controller settings ( HMI Advanced only)
03/2006
10.9.2
Input possibilities for self-optimization
Mechanical system
measurement
Fig. 10-23 Mechanical system measurement
Amplitude:
Input in % of maximum current of power section.
Bandwidth:
The bandwidth should only be changed if the previous optimization routines
did not return satisfactory results (can only be changed in mechanical system
part 1).
Averaging:
Should only be reduced if the traversing range of the machine is insufficient.
Offset:
Constant velocity during the measurement (alternate positive/negative sign for
optimum utilization of the traversing range).
Current control
loop measurement
Fig. 10-24 Current control loop measurement
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-223
10
10 Drive Optimization
10.9 Automatic controller settings ( HMI Advanced only)
03/2006
Amplitude:
Input in % of maximum current of power section.
Bandwidth:
The bandwidth can only be changed in mechanical system measurement
part 1.
Averaging:
Does not normally have to be changed. Affects the quality of the measurement.
Determination of
the proportional
gain
10
Fig. 10-25 Determination of the proportional gain
Frequency at or above which a filter can be used:
Current filters are not used below this frequency.
Min. amplitude:
This figure may not be exceeded between the minimum frequency and the
average frequency (lower adaptation limit).
Max. amplitude:
This figure may not be exceeded at or above the upper frequency limit.
The three frequency entries can be used to modify the starting point and
adaptation range.
10-224
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
10 Drive Optimization
10.9 Automatic controller settings ( HMI Advanced only)
Determination of
the reset time
Fig. 10-26 Determination of the reset time
Frequency at or above which a filter can be used:
Current filters are not used below this frequency.
Min. amplitude:
This figure may not be exceeded between the minimum frequency and the
lower frequency limit (lower adaptation limit).
Max. amplitude:
This figure may not be exceeded at or above the upper frequency limit.
10
The two frequency entries can be used to modify the adaptation range.
Speed control loop
measurement
Fig. 10-27 Speed control loop measurement
Amplitude:
Enter the loading speed in mm/min (should be max. 50% of the offset).
Bandwidth:
Any bandwidth can be selected from the default values in order to check the
automatic controller setting.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
10-225
10 Drive Optimization
10.9 Automatic controller settings ( HMI Advanced only)
03/2006
Averaging:
Affects the quality of the measurement.
Offset:
Enter the loading speed in mm/min (should be at least twice the amplitude).
J
10
10-226
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11
Data Back-up
11.1
General
Implementation:
A data back-up is needed
S after start-up
S after changes to machine-specific settings,
S after servicing (e.g. after hardware is replaced or a software upgrade), to
ensure that operation can quickly be resumed,
S during start-up before altering the memory configuration to make sure that
no data are lost during start-up.
NCK/PLC/HMI
The complete data back-up routine for SINUMERIK 840D is subdivided into the
following:
1. Data back-up for NCK, drive and front operating panel settings
11
2. Data back-up for PLC and data back-up for HMI
Standard system
start-up/archiving
by area
The following data back-up methods are used. They have different purposes:
1. Standard system start-up
So-called standard system start-up files are created to ensure that a certain
configuration can be transferred entirely to other controls running the same
software releases (e.g. running on the same type of machine) as easily as
possible. This type of file cannot be modified externally using an ASCII editor. Series start-up files contain all relevant settings (except for compensation data). Standard system start-up files should be created for NCK, PLC
and for the HMI
2. Series start-up with compensation data
3. Software upgrade
4. Archiving by area
–
Archiving by area is the exception since both machine data 11210 and
the standard system start up allow you to define whether modified machine data should be backed up.
The data on the PLC and the HMI data are not broken down further.
The data back-up ensures that the protection levels set for the definition files
and cycle directories are also backed up and can be restored during standard
system start-up.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-227
03/2006
11 Data Back-Up
11.1 General
Required
accessories
You will need the following accessories in order to back up the data:
S PCIN data transmission program for PG/PC
S V24 cable 6FX2002-1AA01-0BF0
Reference material: /Z/ Catalog NC Z (Accessories)
S PG or PC (DOS)
Structure of the
file names
_N_
Area
Unit
_
Type
S The area specifies which data are to be backed up or retrieved (general,
channel-specific or axis-specific).
S The unit defines the channel, the axis or the TOA area. The unit is omitted if
the entire area has been selected.
S The type determines the type of data. For a data back-up, the file name are
generated and output automatically.
Areas
NC
CH
AX
TO
COMPLETE
INITIAL
Types
TEA
SEA
OPT
TOA
UFR
EEC
CEC
QEC
PRO
RPA
GUD
INI
11
Examples
11-228
general NC-specific data
channel-specific data (unit corresponds to the channel number)
axis-specific data (unit corresponds to the number of the
machine axis)
tool data
all the data in an area
data for all areas (_N_INITIAL_INI)
machine data
setting data
option data
tool data
user input frames: variable NPV, rotations, etc.
measuring system error offset
sag/angularity compensation
quadrant error offset
protection area
R parameters
Global user data
general initialization program (all the data for the active filter system)
_N_COMPLETE_TEA
_N_AX_TEA
_N_CH1_TEA
_N_CH1_GUD
_N_INITIAL_INI
archiving of all machine data
archiving of all axis machine data
archiving of the machine data for channel 1
archiving of the machine data for channel 1
archiving of all the data in the active file system
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11 Data Back-Up
11.4 Data back-up via PG/PC
03/2006
11.2
Data back-up via HMI Embedded
With a PCU 20, the data is backed up via the user interface of the HMI Embedded software.
Details of the procedure can be found in the following documentation:
reference material:
11.3
/IAM/ IM2, HMI EmbeddedStart-up Guide
/BEM/ Operator’s Guide, HMI Embedded
Data back-up via HMI Advanced
With a PCU 50/50.3/70 , the data is backed up via the user interface of the HMI
Advanced software.
Details of the procedure can be found in the following documentation:
Reference material:
11.4
/IAM/ IM4, HMI AdvancedStart-up Guide
/BAD/ Operator’s Guide, HMI Advanced
Data back-up via PG/PC
Via RS-232
The following data can be backed up via the RS-232 interface:
S Standard system start-up: with selection options for the following areas:
–
NCK (complete)
–
PLC (complete)
–
HMI (with option of saving only partial areas of the HMI data)
S Archiving by area: Backing up or reloading of individual data areas (“Data
in”, “Data out” and “Data selection” soft keys)
Error and operator
message texts and
cycle alarm texts
These texts are parts of the front operating panel system software. They must
be reloaded after hardware component replacement or software upgrading. The
messages must be in the correct format (see chapter 13, “Upgrading PCU 20
software”). The texts cannot be read out of the control.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-229
11
03/2006
11 Data Back-Up
11.4 Data back-up via PG/PC
Operating
procedure
(data back-up)
1. Connect the PG/PC
2. In the “Services” area of the HMI,
3. select “RS-232 PG/PC” interface (vertical soft key).
4. Select “Settings” and check or enter the parameter settings of the RS-232
interface (default setting).
Device type:
RTS/CTS
Baud rate:
9600 Baud
Parity:
no
Data bits:
8
Stop bits:
1
XON character:
11H(ex)
XOFF character:
13H(ex)
End of text character: 1AH(ex)
Format:
–
Punched tape format unchecked
for standard system start-up or for backing up
drive data by area (boot files)
–
Punched tape format checked for backing up
all other data by area.
11
11-230
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11 Data Back-Up
11.5 Data back-up via machine data
03/2006
11.5
Data back-up via machine data
Modified values,
backing up,
MD 11210
MD 11210: UPLOAD_MD_CHANGES_ONLY (machine data back-up for modified machine data only) can be used to define, when backing up machine and
setting data, whether all the data or just data that differs from the default setting
should be output via the V24 interface.
UPLOAD_MD_CHANGES_ONLY
MD Number
MD back-up of changed MD only
Standard default: 0
Min. input limit: 0
Max. input limit: 1
Change valid: immediately
Protection level: 2/4
Unit: –
Data type: BYTE
Valid from software version: 1 or 4
Meaning:
Selects a differential MD upload:
11210
Bit 0 (LSB)
Effectiveness of the differential upload on TEA files
0: All data is output
1: Only machine data that differs from the default is output
(only applies to INITIAL_INI). If a value in data stored in the form of an
array is changed, the complete MD array is always output (e.g. MD 10000:
AXCONF_MACHAX_NAME_TAB).
Bit 1
Effectiveness of the differential upload on INI files
0: All data is output
1: Only MDs that have change compared to the compiled value
are output
Bit 2
Change to a field element
0: The complete array is output
1: Only the changed field elements of an arrays are output
Bit 3
R parameters (for INITIAL_INI only)
0: all R parameters are output
1: only R parameters not equal to zero are output
Bit 4
Frames (for INITIAL_INI only)
0: all frames are output
1: only frames that are not zero frames are output
Bit 5
Tool data, cutting parameters (for INITIAL_INI only)
0: all tool data is output
1: only tool data that is not equal to zero is output
Bit 6
Buffered system variables ($AC_MARKER[ ], $AC_PARAM[ ]
for INITIAL_INI only)
0: all system variables are output
1: only system variables that are not equal to zero are output
Bit 7
Synchronous action GUD (for INI files only)
0: all Syna GUDs are output
1: only Syna GUDs that are not equal to zero are output
11
Effectiveness: The change to the data takes effect when the upload for the next
area starts.
corresponds to ....
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-231
03/2006
11 Data Back-Up
11.5 Data back-up via machine data
Note
S It may be useful to perform a data saving operation in which only altered
machine data are saved prior to upgrading software in cases where the
defaults in the new software are not the same as those in the earlier
version. This applies particularly to machine data which are assigned
SIEMENS protection level 0.
Recommendation
MD 11210 UPLOAD_MD_CHANGES_ONLY should be set to “1” or the corresponding bits set to “1”. With this setting, the transferred files contain only those
data which deviate from the default. This is advantageous for future software
upgrades.
Continue from “Standard system start-up” or “Archiving by area”.
11
11-232
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11 Data Back-Up
11.5 Data back-up via machine data
03/2006
11.5.1
Standard system start-up
Standard system
start-up
(data back-up)
5. HMI interface configuration (see above, punched tape format unchecked)
6. Start PCIN data transmission program (“Data In”) on PC/PG.
7. If “Start-up data” is selected via the HMI (HMI “Services” area, data output
“Data Out”), the NCK and PLC areas are suggested when you press the
“Input” key.
8. First select “NCK” (”NCK” is suggested as the name of the archive file) and
start reading the data (“Start” soft key). Follow exactly the same procedure
for the “PLC” data set.
Archiving by area
5. HMI interface configuration (see above: Check punched tape format, apart
from for drive data)
6. Start the PCIN data transfer program (“Data In”) on the PC/PG.Enter file
names.
7. On the HMI, select the data area to be output (HMI “Services” area, data
output “Data Out”):
8. Press the “Data selection” soft key and select the areas to be read. The
“NC-active data” area, for example, contains the following data:
–
Machine data
–
Setting data
–
Option data
–
Global and local user data
–
Tool and magazine data
–
Protection areas
–
R parameters
–
Zero offsets
–
Drive data
–
Compensation data
–
Display machine data
–
Workpieces, global part programs/subroutines
–
Standard and user cycles
–
Definitions and macros
11
When the areas are output, the internal area identifier used in each case
appears on the top line of the display.
9. Start reading the data (“Start” soft key) and acknowledge any input prompts.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-233
03/2006
11 Data Back-Up
11.5 Data back-up via machine data
Note
For the PLC, data back-up can be executed with the SIMATIC tools HiGraph.
Note filter setting for SDBs!
Reference material:
/S7HT/ Manual, Application of Tools
These tools are useful in ensuring portability of the PLC programs.
Downloading
archive data
To read in a complete configuration, a general reset of the control must be
carried out first.
1. Set the protection level to “User” (Password CUSTOMER)
2. Connect the PG/PC to port X6 on the PCU.
3. On the HMI, select the “Services” area. Continue with steps listed under
“Reading in series start-up” or “Reading in area-specific archive data”.
Standard system
start-up
4. Select the interface configuration “V24-PG/PC” as described above
(punched tape format unchecked).
5. Start the PCIN data transfer program on the PG/PC.
Press the “Data out” soft key to start transferring the NCK standard system
start-up file to be transferred to the control.
On the HMI, select the “Services” area,
press the “Data in” soft key and
press the “Start” soft key to start reading.
Acknowledge any input prompts.
11
6. Carry out an NCK reset and general reset of the PLC, then repeat the procedure with the PLC standard system start-up file.
7. Carry out another NCK reset. The control will start up with the new data.
Note
The NCK series start-up file must always be imported before the PLC series
start-up file.
Archiving by area
4. Select the interface configuration “V24-PG/PC” as described above and set
“punched tape format” (unless for drive data).
11-234
–
Start the PCIN data transmission program on the PG/PC. Select the
archive file to be read into control under “Data Out” for transmission.
–
On the HMI, select the “Services” area,
press the “Data in” soft key and
press the “Start” soft key to start reading. The data is detected automatically and downloaded accordingly.
Acknowledge any input prompts.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11 Data Back-Up
11.5 Data back-up via machine data
03/2006
5. Read in the option data and carry out an NCK reset.
6. Load the machine data file and press “NCK-Reset”. If any messages are
then received about reconfiguring the memory or rescaling machine data,
the machine data file must be read in again and the control reset. It is generally necessary to repeat this two or three times.
7. If global user data is activated, the ”N_INITIAL_INI” file (Table 11-1) should
be read. It is read out through selection of the setting “All data” as for areaspecific archiving.
8. Read in archive file for global user data (MAC.DEF and GUD.DEF).
9. Reload the backed up “N_INITIAL_INI” file to activate the global user data.
10. Then load the other areas.
11. The PLC area must be loaded last after a PLC general reset.
Note
S When you are loading drive data, deselect the tape format as well as all
special functions on the right of the display of interface settings.
Do not actuate soft key “Back up boot file” in the drive data menu until you
have reset the control once after loading the drive archive data.
S Check/correct the interface settings after display of a message regarding
memory reconfiguration.
Transmission
errors
If the transmission is canceled with errors, check the following:
S If the password set to the correct protection level.
11
S Are the interface parameters (V24-PG/PC) correct.
S When reading in LEC data, first
set MD 32700 ENC_COMP_ENABLE to 0.
S Set MD11220 INI_FILE_MODE to 1 or 2 (see the “Response to cancellation
when reading in machine data” section below).
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-235
03/2006
11 Data Back-Up
11.6 Data back-up via V24
Table 11-1
Data in _N_INITIAL_INI file
File _N_INITIAL_INI
Data not contained in file _N_INITIAL_INI
S Option data
S Drive machine data
S Machine data
S Compensation data
S Setting data
S Tool offsets
–
–
–
Leadscrew error offset
Quadrant error offset
Sag compensation
S Zero offsets
S Global user data
S Display machine data
S Local user data
S Workpieces
S R parameters
S Global part programs
S Flags in SRAM
S Global subprograms
S Sync.action parameters in S User cycles
SRAM
S Standard cycles
S Definitions and macros
11.6
Data back-up via V24
11
Hardware and
software required
S PG, PC
S RS-232 cable
S PCIN
11-236
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11 Data Back-Up
11.6 Data back-up via V24
03/2006
System overview
PG/PC
PCU 50/50.3/70
V24
Diskette
Hard disk
MPI
CCU1/CCU2
FDD
MSD
RAM
buffered
Fig. 11-1
What data does
the system
contain?
Where are the data
stored?
System overview
Drive data
NC data
PLC data
HMI data
The data is normally stored in the buffered RAM of the NC or PLC. All
the data can also be stored in certain directories on the hard disk of the
PCU 50/50.3/70.
11
Setting for the
V24 interface
When the data is output via the V24 interface, only the archive format is permitted for certain data. This applies to data with the extension ARC and the FDD
and MSD boot files.
If remote diagnostics is active, another RS-232 interface must be used for
reading out the data.
Select the
“Services” area
The “Services” area of HMI Advanced contains an overview of all the programs
or data contained in the NC, PLC, drive and on the hard disk. To view all the
directories, you must first go to the “Select file” screen and set the display accordingly. Only then are the required data displayed to you.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-237
03/2006
11 Data Back-Up
11.6 Data back-up via V24
Outputting data
The sequence of operations for outputting data via the V24 interface applies to
all data. Proceed as follows:
1. Place the cursor on the required data.
2. Press the “Data out” soft key.
3. Press the “V24” or “PG” soft key.
4. Press the “OK” soft key.
5. Read the error log if errors occur while outputting the data.
What do you want
to save?
When backing up data via RS-232 it is not advisable to save all the directories.
Only the data required from re-commissioning are to be output. Use a streamer
for a full back-up of all data.
11
11-238
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11 Data Back-Up
11.7 Data output
03/2006
11.7
Data output
11.7.1
Outputting the drive data via V24
Drive data
Drive data consists of:
S Boot files (MSD.BOT)
S Boot files (FDD.BOT)
S Drive machine data (*.TEA)
Data
Directory
Name
Meaning
Boot file
Diagnosis\FDD data
VS1.BOT
Boot file, 1st axis
Boot file
Diagnosis\MSD data
HS1.BOT
Boot file, 1st spindle
Drive MD FDD
DIAGNOSIS\MachDat/FDD
*.TEA
Drive machine data file for FDD saved
under Start-up/MD/File functions.
Name must be assigned.
Drive MD MSD
DIAGNOSIS\MachDat/MSD
*.TEA
Drive machine data file for MSD
saved under Start-up/MD/File
functions. Name must be assigned.
Where are the boot
files located
The boot files are located in directories FDD data and MSD data.
11
FDD.data
VS1.BOT
VS2.BOT
MSD data (HS1.BOT)
Note
The boot files can only be output as binary files with the V24 “Archive format”
setting. The boot files must be backed up before they are output (“Save boot
files” soft key). The data back-up for the boot files (in binary format) can only be
reloaded to the same software release.
Drive machine data
The drive machine data must first be backed up in the “Start-up” –> “Machine
data” –> “File functions” area before these files can be output via the V24.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-239
03/2006
11 Data Back-Up
11.7 Data output
DIAGNOSIS
MachDat/FDD
MachDat/MSD
11.7.2
Outputting the NC data via V24
NC data
By NC data we mean all data that is located in the SRAM of the NC (without
part programs and cycles).
The following data is stored in the “NC active data” directory:
S NC machine data (MD11210 UPLOAD_MD_CHANGES_ONLY =1)
S Option data
S Setting data
S Tool/machine data
S Work offset
S R parameters
S Global user data
11
S Protection areas
S Compensation data
–
Measuring system error offset (EEC)
–
Beam sag/angular compensation (CEC)
–
Quadrant error offset (QEC)
Structure of the
file header
The file header starts with “%_N” and ends with “_INI”. If you are outputting all
the global user data, the file header is as follows: %_N_COMPLETE_GUD_INI.
In the display NC active data the “central section” of the file header is displayed,
depending on the current cursor position. Look to the right of “Program/Data”.
Example 1
Outputting the measuring system error offset data. If you wish to output the EEC
compensation data via RS-232 you can proceed in two ways:
1. Read out EEC data in their entirety (all axes).
2. Axis-specific output of EEC data.
11-240
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11 Data Back-Up
11.7 Data output
03/2006
Measuring system error offset
Measuring system error offset axis 1
Measuring system error offset axis 2
Measuring system error offset axis 3
Measuring system error offset axis 4
:
:
Measuring system error offset all
If you wish to read out all data, place the cursor on Measuring system error
offset all, otherwise on the relevant axis.
The file header then looks like this:
Example 2
Measuring system error offset, complete:
%_N_AX_EEC_INI
Measuring system error offset, axis 1:
%_N_AX1_EEC_INI
Outputting global user data (GUD). The file header that is sent together with the
data output is shown here, too.
NC active data
Global user data (%_N_COMPLETE_GUD_INI)
Channel user data (%_N_CH_GUD_INI)
User data channel 1 (%_N_CH1_GUD_INI)
11
User data 1 channel 1 (%_N_CH1_GD1_GUD_INI)
User data 2 channel 1 (%_N_CH1_GD2_GUD_INI)
:
:
User
data 9 channel 1 (%_N_CH1_GD9_GUD_INI)
User data complete channel 1 (%_N_CH1_GUD_INI)
Channel user data all (%_N_CH_GUD_INI)
User data all (%_N_COMPLETE_GUD_INI)
NC user data all (%_N_NC_GUD_INI)
NC user data 1 channel 1 (%_N_NC_GD1_GUD_INI)
NC user data 2 channel 1 (%_N_NC_GD2_GUD_INI)
:
:
NC user data 9 channel 1 (%_N_NC_GD9_GUD_INI)
NC user data all (%_N_NC_GUD_INI)
The middle part of the file header, which is sent when the file is read, is displayed at the top of the Program/Data screen: \__NC_ACT\GUD.DIR
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-241
03/2006
11 Data Back-Up
11.7 Data output
Outputting the
initialization
program (INI)
Position the cursor on the Initialization program (INI) directory. Press the “V24”
soft key. The initialization program “%_N_INITIAL_INI” is output with the following data:
S Global user data
S Option data
S Protection areas
S R parameters
S Setting data
S Machine data
S Tool/magazine data
S Zero offsets
No
–
Compensation data (EEC, QEC, CEC)
–
Part programs
–
Definition data and macros
–
Part programs, workpieces, cycles
–
PLC programs and data
–
Display machine data, drive machine data
If you place the cursor on “NC active data” and start outputting the data “via
V24”, an initialization program called %_N_INITIAL_INI is also output, although
this contains all the data in the “NC active data” directory, i.e. with compensations.
11
11.7.3
PLC data
11-242
Outputting the PLC data via V24
The PLC data must first be saved as an archive file before it can be output via
the V24 interface.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11 Data Back-Up
11.7 Data output
03/2006
Procedure
1. Press the “Standard start-up” soft key.
2. Simply select “PLC”.
3. Press the “Archive” soft key.
4. The display is changed and the job log displayed. The “PLC.ARC” file is
created.
5. If the “Job finished” message appears, then press the “Data out” soft key.
6. Select “PLC.ARC” from the “Archive” directory and press the “Interface” soft
key.
7. Make the following settings for V24 with archive format: “Binary format (PC
format)”.
Press “OK”.
8. Now press the “V24” soft key.
Press the “OK” soft key to start outputting the data.
11.7.4
Outputting the HMI data via V24
Display machine
data
Definitions
With the HMI, the display machine data (MD 9000, ...) should be backed up via
the file functions in the “Start-up” area. This machine data is located in the HMI
Advanced RAM, in the “Diagnostics” –> “MachDat” –> “Operating panel” directory. The file name assigned when the data were being stored is displayed in
the directory.
To output the display machine data, place the cursor on the desired file, then
press the “V24” soft key and press the “OK” soft key to confirm. The display
machine data can be output in punched tape format.
The “Definitions” directory contains the definitions for the macros and global
user data. These are, for example:
S SMAC.DEF
(%_N_SMAC_DEF)
S MMAC.DEF
(%_N_MMAC_DEF)
S UMAC.DEF
(%_N_UMAC_DEF)
S SDUD.DEF
(%_N_SGUD_DEF)
S MGUD.DEF
(%_N_MGUD_DEF)
S UGUD.DEF
(%_N_UGUD_DEF)
The definitions can be output via the V24 interface.
Example of GUD data:
Define OTTO
as String
Define HANS
as bool
Define NAME
as char
When installing, the definitions must be read in before the INITIAL_INI file. Only
when the definitions are known to the NC can the actual user data be read in.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-243
11
11 Data Back-Up
11.7 Data output
03/2006
Tool management
data
The data for tool management can be found in the Tool management directory
in HMI Advanced.This directory has three subdirectories:
S Magazine configuration (BEISPIEL_DOKU.INI)
S Tool management configuration (TT110.WMF,....)
S Tool management data (WZACCESS.MDB,....)
The PARAMTM.INI file for configuring the displays and access levels is located
in directory Diagnosis\HMI Initialization\...
11.7.5
Outputting the standard system start-up file via V24
Preparing for
standard start-up
The data selection for standard system start-up must be defined before a standard system start-up file can be defined. Press the “Standard start-up” soft key
and define which data (HMI, NC, PLC) should be backed up.
Selecting the data
Press the “HMI data selection” vertical soft key. In this display you define which
directories are to be contained in the series start-up file.
.
Creating
an
archive file
Select the data.
Press the “OK” soft key. The screen changes.
Press the “Archive” soft key to start creating the “HMINCPLC.ARC” archive file.
When the “Job finished” message appears, the “HMINCPLC.ARC” in the
Archive directory file can be output via the V24 interface.
Set the V24 interface to PC format.
You can also create and output the areas HMI, PLC, NC separately in the form
of series start-up files. The file name then is as follows:
HMI:
HMI.ARC
NC:
NC.ARC
PLC:
PLC.ARC
11
Note
The compensation data EEC, QEC, CEC are not contained in the series setup
file. Reason: Every machine has its own compensation data.
11-244
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11 Data Back-Up
11.8 Backing up the hard disk with Norton GhostR
03/2006
11.8
Backing up the hard disk with Norton GhostR
11.8.1
Hard disk back-up/restore
Functions
S Simple Back-up/Restore of the hard disks of the PCU 50/50.3/70 locally.
System software, add-on software and user-specific records are all backed
up.
S HD image (HD image saved as file) can be saved on a data carrier (e.g. CD)
for long-term purposes.
S Loading of master images (images for series start-up) remains with the machine manufacturer.
S Upgrading or downgrading can be executed by the machine manufacturer
(master image) irrespective of what is supplied by Siemens.
S The Norton Ghost R back-up program is installed on every PCU.
Norton GhostR
Using the “Norton GhostR” software, the entire content of a PCU hard disk is
stored as a disk image. This disk image can be stored on various data carriers
for a later restoration of the hard disk. Norton GhostR is supplied from the
factory on every PCU 50/50.3/70 module.
For further information please see Internet under web site “www.ghost.com”.
PCU 50
The next section describes how to back up an entire PCU hard disk so that both
user and system data remains available and consistent if servicing is required:
S Back up hard disk
S Back up user data
S Copy data to hard disk
Operating
instructions
while program is running with Norton GhostR
HMI BIOS
To enter and make changes in BIOS, you require a keyboard with a PS/2 connector (a PG keyboard also works).
From Bios 3.04, press the “DEL” key when powering up the HMI. Loading the
“BIOS Setup Defaults” allows BIOS settings to be reversed.
PCU
With the PCU, in the event of a hard disk restore, the “Virus Warning: Disabled”
setting must be made in the BIOS. This change is not needed for the back-up.
Memory required on
the PC/PG
The PC/PG hard disk must have around 70% of the PCU hard disk space as
free memory for the back-up image file.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-245
11
11 Data Back-Up
11.8 Backing up the hard disk with Norton GhostR
Back-up/Restore via
parallel cable
03/2006
on the PG/PC
S PC/PG with bidirectional interface, EPP setting
S LapLink–Siemens parallel cable (Order no. 6FX2002-1AA02-1AD03) commercial LapLink cable
S For PCU, set the parallel port to EPP (Bios), which will increase the transmission speed of the parallel interface by approximately 10%.
Supplementary
conditions
1. Back-up/restore at the file level is done using HMI Advanced in the
“Services” area, e.g. by selectively backing up start-up and machine data,
etc. (via V.24, network, PC card)
2. Individual software components are installed/reinstalled either via PC card
or via the parallel port (Interlnk/ InterSrv). Please take note of the BIOS updating problems.
3. If you back-up/restore via the parallel port of network, the power saving
circuit of the external PC/PG must be switched off.
4. After backing up/restoring with Ghost, the parallel cable should be unplugged to avoid unpredictable HMI operating states.
5. If the external PC is equipped with an AMD K6 processor, problems may
arise with the parallel connection if the processor cycle is >233 MHz. In this
case, both computers (PCU and PC) should be operated with the LPT Bios
setting “ECP”.
6. Occasionally, access problems to the CD ROM drive are encountered with
some PGs. In this case, a ghost connection abort may incur after a direct
restore of an image file from a CD ROM.
Remedy: Copy the image file from the CD to the PG hard disk.
11
Functions of
Norton GhostR
S Saving of complete hard disks in an image file
S Restoring hard disks from an image file
S Compressing of image files
S In-built coupling via LPT port master/slave, e.g. from PCU with PG (without
Interlnk/Intersrv)
S Supporting long file names
S Disk integrity and image file “Integrity Check”
S Reloading of image files to unformatted hard disk (“on-the-fly formats”)
S New target hard disk can be larger or smaller (if data volume not too large)
than the original
S When copying hard disks with several partitions, the size of the partitions
can be changed.
S Command interface for the integration of batch files
S Menu interface for interactive operation
11-246
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11 Data Back-Up
11.8 Backing up the hard disk with Norton GhostR
03/2006
11.8.2
Saving user data
The “Services” area of the HMI can be used to back up PLC, NC and HMI data
using the “Standard system start-up” function.
Reference material:
/BAD/ HMI AdvancedUser Guide
Requirement: Set password
1. Select the “Services” area.
2. Press the “Standard start-up” soft key.
3. Press the “HMI data selection” soft key.
4. Select the data to be archived.
5. Select the destination to start archiving:
–
“Archive” directory on the hard disk
–
“Archive” directory on the NC card
6. The soft key label changes to “...Stop”. The Standard system start-up
archive is created.
11.8.3
Backing up the hard disk
Requirement:
S Norton Ghost version 6.x/7.x (Windows XP required, >= 7.x) must be
installed on the PCU and on the PG/PC.
S The Ghost versions must be the same on the PCU and PG/PC.
S Directory where the image file is to be stored exists on PG/PC.
S There must be enough free memory on the PG/PC.
S Any version of Windows running on the PG/PC.
S PCU and PG/PC are connected with the Ethernet cable.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-247
11
03/2006
11 Data Back-Up
11.8 Backing up the hard disk with Norton GhostR
ÉÉÉÉ
ÉÉÉÉ
ÉÉÉÉ
ÉÉÉÉ
ÀÀÀÀÀ
ÀÀÀÀÀ
ÀÀÀÀÀ
Ethernet
Ethernet
PCU
PG/PC
1. Switch off and on control and select setup mode (press key 6 if DOS window
appears)
2. Select menu “7: Back-up/Restore”
3. Enter the password
4. Select menu “1 hard disk back-up/restore with ghost”
5. < only if presetting is not correct >
Set parameter for Norton Ghost program:
–
< 1 > configure ghost parameters:
If you wish to change the preset directory path or the type of interface,
choose menu item 1 from:
* Change interface (set connection mode):
<1> PARALLEL (default setting)
<2> LOCAL
select and confirm the relevant option
* Change path:
<3> Change back-up image file name (set up directory for back-up file
on the PG, e.g. C:\SINUBACK\PCU\HMI.gho)
<4> Change restore image file name (set up complete path for restore
file “MMC.GHO” on the HMI, e.g. D:\SINUBACK\HMI\MMC.GHO)
select the relevant option, enter and confirm the path
11
–
Prompt: Save GHOST parameters? answer “Yes”.
<5> Back to previous menu
Return to main menu
6. Execute hard disk back-up
–
< 2 > Hard disk back-up to <path name>, Mode: LOCAL/NETWORK
* When you select this menu, a message appears:
You are prompted to check whether a connection has been
established between the HMI and PG/PC.
The destination path for the HMI image directory is displayed.
The back-up is to be generated from this directory.
* PG/PC:
Start the Ghost program in a DOS window or at the DOS level
using the command ghost –lps.
11-248
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11 Data Back-Up
11.8 Backing up the hard disk with Norton GhostR
03/2006
* PCU:
Click on “Y” to acknowledge the prompt and start the back-up.
* PCU:
A Norton Ghost message window appears. This contains:
The transfer progress
The paths used
Information about the amount of data to be transferred
PCU
If the back-up is canceled, a prompt appears:
Do you want to try to back-up again [Y,N] ?
Click on N to acknowledge and call up the main menu.
Click on “Y” to restart the back-up.
–
11.8.4
< 4 > Back to previous menu
Return to main menu
Copy data to hard disk
S Version 6.x/7.x of the Ghost program is installed on the PCU and on the
PG/PC.
S The directory for storing the restore image has been created on the PG/PC.
S Any version of Windows is installed on the PG/PC.
S PCU and PG/PC are connected with the Ethernet cable.
ÉÉÉÉ
ÉÉÉÉ
ÉÉÉÉ
Ethernet
ÀÀÀÀÀ
ÀÀÀÀÀ
ÀÀÀÀÀ
11
Ethernet
PCU
PG/PC
1. Switch on the PG and insert CD into drive.
2. Switch off and on control and select setup mode (press key 6 if DOS window
appears).
3. Select menu “7: Back-up/Restore”
4. Enter the password
5. Select menu “1 hard disk back-up/restore with ghost”
6. Set the parameters for the Norton Ghost program:
–
<1> Configure GHOST Parameters:
see above
7. Restore contents of hard disk
–
< 2 > Hard disk back-up to <path name>, Mode: LOCAL/NETWORK
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-249
11 Data Back-Up
11.8 Backing up the hard disk with Norton GhostR
03/2006
* When you select this menu, a message appears:
You are prompted to check whether a connection has been
established between the HMI and PG/PC.
The destination path for the HMI image directory is displayed.
The back-up is to be generated from this directory.
* PG/PC:
Start the Ghost program in a DOS window or at the DOS level
using the command ghost –lps.
* PCU:
Click on “Y” to acknowledge the prompt and start the back-up.
* PCU:
A Norton Ghost message window appears. This contains:
The transfer progress
The paths used
Information about the amount of data to be transferred
PCU
If the back-up is canceled, a prompt appears:
Do you want to try to back-up again [Y,N] ?
Click on N to acknowledge and call up the main menu.
Click on “Y” to restart the back-up.
–
< 4 > Back to previous menu
Return to main menu
8. The system boots automatically after a successful restore operation.
Duration:
approx. 15–20 minutes
Note
11
Back-up of user data, machine data and start-up files is an integral feature of
the HMI in the Services operating area.
The storage location and format of the data to be saved, and the medium on
which they can be stored or restored from, are displayed in the File Manager.
Reference material:
11-250
/IAM/ IM4, HMI AdvancedStart-up Guide
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11 Data Back-Up
11.9 Backing up the current image of the latest software
03/2006
11.9
Backing up the current image of the latest software
Backing up the
latest software
If you wish to create an image of your current software, proceed as follows:
Requirement:
The Ghost program must be installed on the PCU.
1. Switch on the control and select setup mode (press key 6 if the DOS window
appears).
2. Select menu “7: Back-up/Restore”
3. Enter the password
4. Select menu “4: Partitions Back-up/Restore”
5. Change the maximum number of available images if necessary:
Menu “1: Configure Ghost Parameter”
Then use menu “1: Change Maximum Back-up Images” to define how many
images you want to allow. Up to 7 images are possible. Default setting: 1.
6. To save the current software, select
Menu “2: Partitions Back-up” and enter a descriptive text that will help you to
find the image in future in order to restore it.
7. The backed up software is stored in the “D:\Images” directory and is listed
when you select Menu “3: Partitions Restore”.
Restoring the
latest software
If you wish to use an image you have created of your current software, proceed
as follows:
Requirement:
The Ghost program must be installed on the PCU.
1. Switch on the control and select setup mode (press key 6 if the DOS/
Windows window appears).
2. Select menu “7: Back-up/Restore”
3. Enter the password
4. Select menu “4: Partitions Back-up/Restore”
5. To restore the image, select
Menu “3: Partitions Restore”
6. Choose a software version from the list of available versions.
7. The system boots automatically after a successful restore operation.
Deleting a software image from
the “Images”
directory
If you wish to delete a software image from the “Images” directory, proceed as
follows:
Requirement:
The Ghost program must be installed on the PCU.
1. Switch on the control and select setup mode (press key 6 if the DOS/
Windows window appears).
2. Select menu “7: Back-up/Restore”
3. Enter the password
4. Select menu “4: Partitions Back-up/Restore”
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-251
11
03/2006
11 Data Back-Up
11.9 Backing up the current image of the latest software
5. To delete a software image, select
Menu “4: Delete Image”
6. Choose a software version from the list of available versions.
7. The deleted software image is removed from the “D:\Images” directory and
is no longer listed when you select Menu “3: Partitions Restore”.
Norton Ghost
Two versions of the Norton Ghost software are available on the control:
S Norton Ghost version 5.1b (default)
S Norton Ghost version 6.01
From Norton Ghost version 5.1c onwards, the data format has changed, which
means that earlier versions of Norton Ghost, i.e. < V 5.1c, are unable to read
the new data format.
If the latest version 6.01 is required (because a more recent version is installed
on the PG/PC, for example), this can be activated via the Service menu.
1. Switch on the control and select setup mode (press key 6 if the DOS/
Windows window appears).
2. Select menu “7: Back-up/Restore”
3. Enter the password
4. Select “Switch to other version of GHOST”. The active version of Norton
Ghost appears at the top of the screen.
Transfer using LPT
parallel port
11
For a transfer using the LPT parallel port, the Norton Ghost software cannot be
mixed with old (< V 5.1c) and new (>V 5.1b) versions. During the transfer, it
should be ensured that a compatible data format is transferred:
S Norton Ghost V5 up to and including V5.1b
or
S Norton Ghost V5.1c up to and including V6.x
11-252
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11 Data Back-Up
11.10 Installing a replacement hard disk
03/2006
11.10
Installing a replacement hard disk
PCU 50/70
The next section describes how to restore the data back-ups of an entire
PCU 50/70 hard disk so that both user and system data remains available and
consistent if servicing is required.
Norton GhostR
Using the “Norton GhostR” software, the entire content of a PCU 50/70 hard
disk is stored as a disk image with HMI Advanced. This disk image file can be
stored on various data carriers for later restoration of the hard disk.
Norton GhostR is supplied from the factory on every PCU 50/70 module and the
spare hard disk.
For further information please see web site “www.ghost.com” or the previous
chapter.
Recommendation
Archive the hard disk back-up (image), including the “Norton Ghost” program,
on a CD.
Restore back-up
copy
Requirement:
S Ghost program is installed on the PG.
S A new replacement hard disk is installed.
S Connect the PCU to the PC/PG using a parallel cable
S One of the operating systems Windows 3.x, Windows 95 and a CD drive is
ÉÉÉÉ
ÉÉÉÉ
ÉÉÉÉ
ÉÉÉÉ
available on the PC/PG.
LPT:
(X8)
PCU 50/70/
HMI Advanced
ÀÀÀÀ
ÀÀÀÀ
ÀÀÀÀ
ÀÀÀÀ
LPT:
PG/PC
CD
1. Fit the new spare hard disk in the PCU 50/70
(see enclosed instructions)
–
Place hard disk onto hinges
–
Plug in the connecting cable from the hard disk to PCU
–
Mount hard disk using the 4 knurled screws
–
Release the transport retainer: turn to “operating” until it engages.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-253
11
03/2006
11 Data Back-Up
11.10 Installing a replacement hard disk
Note
The Windows operating system and HMI system software are not installed on
the replacement hard disk.
2. Switch on the PG and insert CD into drive.
3. Switch off and on control and select setup mode (press key 6 if DOS window
appears).
4. Select menu “4: Back-up/Restore”
5. Enter the password
6. Select menu option 1 “Hard disk back-up/restore with ghost”
7. Set the parameters for the Norton Ghost program:
–
< 1 > configure ghost parameters:
see above
–
<3> Hard disk restore from <path name>, PARALLEL mode
* When you select this menu, a message appears:
You are prompted to check whether a connection has been
established between the control and PG/PC.
The image file is displayed for the control onto which
the restore is to be loaded.
* PG/PC:
Start Norton Ghost in a DOS window or at the DOS level
by entering the command ghost –lps to start the
program.
* HMI:
11
Acknowledge (Yes) the message window to start the restore.
* HMI:
A Norton Ghost message window appears. This contains:
The transfer progress
The paths used
Information about the amount of data to be transferred
Note
If the data transfer is interrupted during the restore operation, the system on the
hard disk is incomplete. A control boot diskette is therefore needed. This must
contain the MS-DOS 6.X boot and the Norton Ghost software.
–
< 4 > Back to previous menu
Return to main menu
8. After a successful restore, the control is automatically rebooted.
Duration:
approx. 15–20 minutes
to generate a compressed disk image = 130 MB of a
540 MB hard disk via LPT.
11-254
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11 Data Back-Up
11.11Data back-up with VALITEK streamer with the PCU 50
03/2006
11.11
Data back-up with VALITEK streamer with the PCU 50
What can you
back up?
Using the VALITEK streamer you can
S back up all data on hard disk C (Back-up all)
S back up the user data (archive format) in directory C:\DH\ARC.DIR (Back-up
User Data)
S restore the data back-up (Restore from Tape)
Streamer
connection
The VALITEK streamer is connected to the parallel port X8 (25-pin) on the
PCU 50/70 using only the SIEMENS cable 6FC9 344-4xV. No other data
back-up device can be connected since the software is designed to operate
with the VALITEK streamer.
Operation
While the HMI is booting (after switching on the control system)
when the message Starting MS DOS appears:
1.
Press the 6 key once briefly on the front operating panel keyboard.
The following menu is displayed:
PLEASE SELECT:
1 Install/Update MMC System
2 MMC Configuration Tool
3 DOS Shell
4 Start Windows (Service Mode)
5 MMC System Check
6 Reboot System (Warmboot)
7 Back-up / Restore
8 Start PC Link
9 End (Load MMC)
11
Your Choice [1,2,3,4,5,6,7,8]?
2.
Press key 7.
The system asks you to enter a password:
passwd:
3. Enter a password for level 0 to 2.
– System
– Manufacturer
– Service
The following menu is displayed:
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-255
11 Data Back-Up
11.11 Data back-up with VALITEK streamer with the PCU 50
03/2006
PLEASE SELECT:
1 Select VALITEK Streamer Type
2 Test Connection to Streamer
3 Back-up System
4 Back-up Userdata
5 Restore from Tape
6 Uninstall MMC102/103 (Delete Files)
7 Return to Main Menu
Your Choice [1,2,3,4,5,6,7]?
4. Press key 1
The following menu is displayed:
*** No Streamer configured ***
Please select (new) Streamer type:
1 Valitek PST-160
2 Valitek PST2-M1200
3 Return to previous Menu
Your Choice [1,2,3]?
5. Select the streamer type, e.g. No. 2.Valitek PST2-M1200. The streamer type
is then selected and you return to the selection menu.
PLEASE SELECT:
1 Select VALITEK Streamer Type
2 Test Connection to Streamer
3 Back-up System
4 Back-up Userdata
5 Restore from Tape
6 Uninstall MMC102/103 (Delete Files)
7 Return to Main Menu
11
Your Choice [1,2,3,4,5,6,7]?
6. You can also select the streamer connection. To do this, select menu
option 2
The message for the selected streamer type is displayed:
*** Current Configuration: Valitek PST2-M1200 ***
Press any key to continue ...
The test run then starts.
11-256
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
11 Data Back-Up
11.11Data back-up with VALITEK streamer with the PCU 50
Valitek PST2 system
Verify Connection
Activity
Reading Status
Sending Test Data Blocks
Receiving Test Data Blocks
Selected Port : lpt1
Repetitions
500
500
500
Rom Version 85 Revision B
Connection
0
0
0
<esc>–Abort
Test complete. The connection is functional. Press a key ...
7. You can now, for example, create a complete back-up of all system data. To
do this, select 3, Back-up System means hard disk C.
PLEASE SELECT:
1 Select VALITEK Streamer Type
2 Test Connection to Streamer
3 Back-up System
4 Back-up Userdata
5 Restore from Tape
6 Uninstall MMC102/103 (Delete Files)
7 Return to Main Menu
Your Choice [1,2,3,4,5,6,7]?
The following message appears on the screen:
*** Current Configuration: Valitek PST2–M1200 ***
11
Backing up Partition C: ....
Continue ?
Your Choice: [Y,N]?Y
Start the data back-up by pressing Y.
8. By pressing key 4, Back-up User Data, you opt to create a back-up of the
user data, i.e. batch file C:\TOOLS\BACK_USR.BAT is executed. All archive
files under C:\DH\ARC.DIR are backed up as standard. If you want to back
up additional files, then you must enter other directories in file C:\TOOLS\
BACK_USR.BAT.
PLEASE SELECT:
1 Select VALITEK Streamer Type
2 Test Connection to Streamer
3 Back-up System
4 Back-up Userdata
5 Restore from Tape
6 Uninstall MMC102/103 (Delete Files)
7 Return to Main Menu
Your Choice [1,2,3,4,5,6,7]?4
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-257
11 Data Back-Up
11.11 Data back-up with VALITEK streamer with the PCU 50
BACK_USR.BAT
03/2006
The file may only be modified at the point indicated. The content of file
BACK_USR.BAT is as follows:
~~C:\
REM Save Archives in DH:\ARC.DIR
>> c:\dh\arc.dir\
*.*
REM Save this file
>> c:\tools\
back_usr.bat
[ ...Here you can specify the directories that are to be backed up, e.g. >>
c:\dh\mb\
*. *]
REM The following line must be the last !
$$
The following message appears on the screen:
*** Current Configuration: Valitek PST2-M1200 ***
Backing up User Data ....
Continue ?
Your Choice: [Y,N]?Y
Start the data back-up by pressing Y.
11
9. You can opt to restore the backed up data by selecting option 5.
PLEASE SELECT:
1 Select VALITEK Streamer Type
2 Test Connection to Streamer
3 Back-up System
4 Back-up Userdata
5 Restore from Tape
6 Uninstall MMC102/103 (Delete Files)
7 Return to Main Menu
Your Choice [1,2,3,4,5,6,7]?5
The following message appears on the screen:
*** Current Configuration: Valitek PST2-M1200 ***
Restoring from Tape ....
Continue ?
Your Choice: [Y,N]?Y
You can start restoring the back-up data from tape by selecting Y.
11-258
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
11 Data Back-Up
11.11Data back-up with VALITEK streamer with the PCU 50
10. Press 6 to delete the HMI Advanced System, including stored data
PLEASE SELECT:
1 Select VALITEK Streamer Type
2 Test Connection to Streamer
3 Back-up System
4 Back-up Userdata
5 Restore from Tape
6 Uninstall HMI (Delete Files)
7 Return to Main Menu
Your Choice [1,2,3,4,5,6,7]?6
Do You REALLY want to delete Your HMI Advanced system ?
Your Choice: [Y,N]?Y
Y will delete all the data in the C:\HMI\*.* and C:\DH\*.* directories. MS-DOS and
WINDOWS operating systems are not deleted.
11
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-259
03/2006
11 Data Back-Up
11.12 Line checksums and MD numbers in MD files
11.12
Line checksums and MD numbers in MD files
Line checksums have been introduced when creating back-up files for machine
data (INI and TEA files). This means that they can not be checked.
The introduction of MD (machine data numbers) into the back-up files makes it
easier to understand the machine data values when servicing is required and, if
necessary, allows machine data back-up files to be processed automatically.
By backing up the files, the “Manufacturer” write access right can be avoided
when restoring.
The two sections below give detailed information about line checksums and
machine data numbers.
11.12.1 Line checksums (MD 11230 MD_FILE_STYLE)
Properties of
line checksums
A line checksum
S is generated only for lines with machine data assignments.
S is positioned directly after the machine data assignment, preceded by a
blank and apostrophe.
S comprises 4 HEXA characters.
S is only generated by the control when a machine data back-up file is generated. It is not created by external editors on the PC or PG.
S is activated via MD 11230 MD_FILE_STYLE.
11
S can be output together with machine data numbers.
S “; <comment >” can be added later without affecting the sum check.
MD 11230
MD_FILE_STYLE
If MD
11230=
Evaluating line
checksums
11-260
then output of
Example
0
MD name
$MC_AXCONF_MACHAX_USED[0]=1
1
MD name with line
checksum
$MC_AXCONF_MACHAX_USED[0]=1 ’2F34
2
MD name and MD
number
N20070$MC_AXCONF_MACHAX_USED[0]=1
3
MD name, MD
number and line
checksum
N20070$MC_AXCONF_MACHAX_USED[0]=1 ’2F34
When machine data files are read in with valid line checksums, no write access
right is needed.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11 Data Back-Up
11.12Line checksums and MD numbers in MD files
03/2006
“Manufacturer” rights are needed to read in the following data:
S machine data without line checksum
S modified machine data values with deleted line checksum
When loading machine data files, you can choose how the system must react to
errors in the machine data file. See Abort procedure subsection 11.12.3.
If the file contains errored values, then the current values are never overwritten.
11.12.2 Machine data numbers
Archive files
S Machine data numbers formally precede a machine data assignment line as
block numbers (e.g. N20070).
S There is a blank between the machine data number and machine data
assignment.
S The machine data number relates to the machine data record as a whole.
Any existing field values are not reflected in the machine data number.
S The generation of machine numbers in front of machine assignment lines in
INI and TEA files can be activated or deactivated.
Evaluating
MD numbers
–
MD 11230 MD_FILE_STYLE Bit 1 = 1
Generate machine data number
–
MD 11230 MD_FILE_STYLE Bit 1 = 0
number
Do not generate machine data
When machine data files are restored, the control evaluates the machine
numbers as follows:
S If errors are identified in the machine files as they are read in, then the
machine number is displayed as a block number with the corresponding
alarm.
11.12.3 Response to canceling while reading in machine data
Response to
canceling
When machine data files (INI files)
S which contain errors
S which do not match the checksum
are read into the control, alarms are generated. The import operation may be
aborted. The following responses by the control can be selected by setting machine data MD 11220 INI_FILE_MODE:
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-261
11
03/2006
11 Data Back-Up
11.12 Line checksums and MD numbers in MD files
MD 11220 value
Response to errors
0
Output an alarms, cancel on detecting the 1st error. (As for
SW versions 1 and 2.)
1
Output of an alarm, import continues, output of number of
errors at file end by an alarm.
2
Import continues to file end in spite of any errors. Output of
number of errors at file end by an alarm.
In all cases with at least one error in the machine data file, the name of the
affected file is output with the first alarm (alarm 15180).
Further reactions:
S Defective machine data does not overwrite current machine data.
S If an attempt is made to load machine data without line checksums without
sufficient authorization, the machine data is not overwritten.
S CHANDATA instructions for non-implemented channels (machine data for
multiple channels is not set) causes processing to be canceled.
S Invalid file end aborts the import operation.
MD 11220
INI_FILE_MODE
MD 11220 INI_FILE_MODE must be reset explicitly. An earlier setting is not
validated in the course of series start-ups.
Example:
S Read in machine data and output alarms generated while reading in.
S % character represents the file name and number of errors.
11
S MD 11220 = 1, i.e. output an alarm in response to every error, continue
import, output number of errors at end of file through an alarm.
Machine data file
Alarms
CHANDATA(1)
$MC_AXCONF_GEOX_NAME_TAB[0]=”X”
$MC_AXCONF_GEOX_NAME_TAB[1]=”Y”
15180 Cannot process program % as an INI file
$MC_AXCONF_GEOX_NAME_TAB[99]=”A”
17020 Illegal array index1
$MC_MM_REORG_LOG_FILE_MEM=1000
17090 Value higher than upper limit
$MC_AXCONF_GEOX_NAME_TAB=”X”
12400 Element does not exist
$MC_MM_REORG_LOG_FILE_MEM[1]=100
12400 Element does not exist
$MN_UNKNOWN_MD=1
12550 Name % not defined
M17
15185% Error detected in INI file
11-262
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11 Data Back-Up
11.13 Machine/setting data
03/2006
Upgrade from software version 6.4
Machine data for non-activated channels is ignored and does not cause the
reading of an archive to be canceled.
Channels are activated by the settings in machine data
MD 10010: ASSIGN_CHAN_TO_MODE_GROUP.
Channel machine data for channels for which a BAG=0 is assigned are ignored
when read.
The alarm generation options via MD 11220: INI_FILE_MODE also apply here.
Errors only relate to the data errors that are read in for channels to be downloaded.
Application:
Standard system start-up for various machines via a standardized archive file
that was created for the largest machine of a class of machines. For the smaller
machines, only the
MD 10010: ASSIGN_CHAN_TO_MODE_GROUP is set so that only those
channels that can be processed by smaller machines are activated.
Changing the archive file:
The SinuCom ARC program can be used to change the archive file in
MD 10010: ASSIGN_CHAN_TO_MODE_GROUP.This program is part of the
SinuCom NC start-up software which is described in
Reference material:
/INC/ Start-up Tool SINUMERIK SinuCOM NC.
ALARM:
If machine data that should be ignored is identified when the archive is read in,
warning alarm 15025: “Channel %1 block %2 CHANDATA: Channel is not active. %3 data will be ignored” is output.
11.13
Machine/setting data
11
The machine/setting data is listed in
Reference material:
/LIS/ Lists
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
11-263
03/2006
11 Data Back-Up
11.14 Back up PLC data
11.14
Back up PLC data
Original image of
project
The consistency of the PLC data back-up is guaranteed only if you take the
following steps in the given order:
1. Switch PLC to PLC STOP (set PLC switch S4 to position 2)
2. Transfer PLC data from PG to control
3. Archive PLC data
4. Switch PLC to PLC-RUN (set PLC switch S4 to position 0)
If you following this sequence of steps, an original image of the project will be
generated in the data management system.
Instantaneous
image of PLC-CPU
If you cannot perform the operations described above, you can – as an alternative – switch the PLC from PLC-RUN to PLC-STOP:
1. Switch PLC to PLC STOP (set PLC switch S4 to position 2)
2. Archive PLC data
3. Switch PLC to PLC-RUN (set PLC switch S4 to position 0)
If you following this sequence of steps, an instantaneous image of the PLCCPU content will be generated in the data management system.
Note
If you back up the PLC data while the PLC is operating in cyclic mode (PLCRUN), the data blocks are not backed up at the same time. This may result in a
data inconsistency that causes the PLC to stop in the user program.
11
J
11-264
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Replacing Software and Hardware
12.1
12
Software update
Note
Sequence for updating software during start-up or software replacement
1. Upgrade HMI
2. Upgrade NCK software
Please note the information in the ReadMe file sent with the ToolBox.
Naming
convention
for the
PCMCIA card
A PCMCIA card is used for the NCU. On the outside, this looks just like the
card with the HMI software, so it is easy to confuse the two. To help distinguish
between the two, the PCMCIA card
S for the NCU is called the “NC card” below and
S the one for the HMI is called the “PC card”.
Every time the software is supplied, the ToolBox contains a ReadMe file that
describes the latest control upgrade.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
12-265
12
03/2006
12 Replacing Software and Hardware
12.1 Software update
12.1.1
Sequence
Standard upgrade
The software can be updated, without having to open the device, via the card
drawer unit on the front panel.
S Please save all control and user data before commencing with the upgrade
(see Chapter 11, “Data Backup”).
S Switch the control off.
S Place the PCMCIA card with the new firmware into the card drawer.
Carry out the following steps:
1. Turn switch S3 to 2 (Export software is updated)
2. Switch on power
3. During booting, the firmware is transferred from the memory card to the
device
4. Wait until “9” appears on the display
5. Turn switch S3 to 1 (standard software is updated)
6. Wait until “6” appears on the display
7. Set switch S3 to 0
8. General reset of the PLC: turn switch S4 to “2”, and then to “3”. Switch into
positions (“2”–“3”–“2”) within 3 seconds. After the PS and PF LEDs light up,
set switch S4 to position “0” (see Section 5.2 Power-On/Power-Up).
9. Then proceed as described in Section 11.2 (Series start-up) to import the
saved data again. Read any notes about the new software release.
Note
12
If the digit “6” is not displayed, then an error has occurred:
–
Invalid card?
–
The software and hardware do not match (e.g. PC card NC with software
for NCU 572.2 inserted in a NCU 573.2)
–
Card or hardware is defective
The PCMCIA card with the system software must remain inserted during
operation
Removing and inserting the PCMCIA card under voltage can lead to data
losses.
12-266
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
12 Replacing Software and Hardware
12.4 Standard system start-up via NC card
03/2006
12.2
Software upgrade for HMI Embedded
Form supplied
The entire HMI Embedded software package is supplied on a CD-ROM. The
software is loaded using the Service menu.
The software upgrade procedure is described in the following publication:
Reference material:
12.3
/IAM/ IM2, HMI EmbeddedStart-up Guide
Software upgrade for HMI Advanced
Form supplied
The entire HMI Advance software package is supplied on a CD-ROM. The software is loaded using the Service menu.
The software upgrade procedure is described in the following publication:
Reference material:
12.4
/IAM/ IM4, HMI AdvancedStart-up Guide
Standard system start-up via NC card
The free memory on the NC card (PCMCIA card) can be used to save a start-up
archive there. The archive can be copied to the NC card using SINUCOPY-FFS
(on an external PG/PC).
12
Possible applications:
1. After replacing an NC module (or another form of data loss), the user can
restore the machine to its original state as it was supplied by the manufacturer
using the archive stored on the NC card or
2. The machine manufacturer can provide the cycles and data in the archive on
the NC card when he supplies the machine or a software upgrade.
You have the option of transferring Siemens and/or machine manufacturer
cycles from the flash file system on the NC card to the DRAM when the control
powers up and running them from there. The configuration for this and the
behavior of the DRAM cycles are described in 12.4.1.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
12-267
12 Replacing Software and Hardware
12.4 Standard system start-up via NC card
Sequence of
operations
03/2006
A) Create a start-up file on the NC card
Requirement:
The SINUCOPY_FFS software has been loaded.
1. Output series start-up data from NC/PLC via RS-232 to a PG/PC.
2. Store series start-up data on the PG/PC as ORIGINAL.ARC file
(e.g. in \tmp).
3. Call SINUCOPY-FFS on the PG/PC.
4. Insert the NC card in the PCMCIA slot.
5. Copy the NC SW to the PC card.
6. Choose “Area settings” in the NC card menu.
Enter 0 under “FFS Startadr” and “FFS Endadr”.
7. Choose the “Create new FFS” field and click on the field “Detect automatically”.
8. Format the FFS on the NC card.
9. Choose the “Create DIR” field in the FFS menu and create and open the
directory _N_ARC_DIR.
10. Call the “Save FFS from hard disk to card [Archive/part programs]”. The data
are loaded to the NC card.
Note
The created start-up file can be saved directly to the NC card.
12
12-268
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
12 Replacing Software and Hardware
12.4 Standard system start-up via NC card
03/2006
B) Load the start-up file from the NC card
Requirement:
The start-up archive called _N_ORIGINAL_ARC can be found on the NC card
(under the _N_NC_CARD_DIR\_N_ARC_DIR directory).
1. Insert the NC card in the NCU module
Start-up switch =1 (NCK general reset)
Press NCK reset and wait until the 7-segment display reads “6”
Start-up switch =0 (NCK general completed)
When the “6” appears, the start-up switch can be set to default position “0”
2. Set a password
3. Press the “ETC key” in Services basic display and press the “Original status”
soft key.
This soft key is only available if the NC card contains the above-mentioned
start-up archive and access level 3 (User) has been set at the control.
4. When the soft key is pressed, the log window appears with the prompt:
“Standard start-up archive: Run standard system start-up?”. Confirm to load
the data.
Note
If no PLC program is active, it takes longer to input the data (because the PLC
timeout is effective).
!
Caution
The complete data of the NC (and PLC, if included in the start-up archive) of
the user is deleted and replaced by the data in the start-up archive.
12
12.4.1
Cycles
DRAM for storing cycles and programs
Cycles remain generally unchanged after running in.
They are therefore suitable for processing from the DRAM, which is available
from software version 6 onwards. This means that scarce SRAM memory can
be used for other purposes.
Programs
The option of processing programs from the DRAM should only be used if there
are no more changes to be made and it is important to save on RAM usage.
The “Processing from DRAM” function is available as an option.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
12-269
03/2006
12 Replacing Software and Hardware
12.4 Standard system start-up via NC card
Loading
The cycles are located in the flash file system FFS on the NC card in the following directories:
_N_CST_DIR
Siemens cycles
_N_CMA_DIR
Machine manufacturer’s cycles
from software version 6.4:
_N_CUS_DIR
User cycles
_N_MPF_DIR
Part programs
_N_SPF_DIR
Subprograms
_N_WKS_DIR
Workpieces
are also provided or loaded by the HMI software.
Selection for
DRAM processing
The objects to be processed from the DRAM are specified by MD 11290:
DRAM_FILESYSTEM_MASK. If the MD is set to 0, then the objects are processed from SRAM as standard.
Bit = 0
The files in the directory are processed from SRAM
Bit = 1
The files in the directory are processed from DRAM
Assignment of bits to the directories
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
12
Backing up to a
background
memory
Siemens cycles, CST directory
Machine manufacturer cycles, CMA directory
User cycles, CUS directory
Part programs, MPF directory
Subprograms, SPF directory
Workpieces, WKS directory
From software version 6.4, you can decide whether the files to be processed
from the DRAM should be backed up to the Flash file system of the NC card so
that they are available in DRAM once more after the NC is powered on. If you
choose not to do this, they will have to be loaded again from the HMI.
The type of back-up is controlled by MD 11291 : DRAM_FILESYST_SAVE_MASK.
Bit = 0
The files in the directory are not backed up
Bit = 1
The files in the directory are backed up to the Flash file system of
the NC card
Assignment of bits to the directories
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Siemens cycles, CST directory
Machine manufacturer cycles, CMA directory
User cycles, CUS directory
Part programs, MPF directory
Subprograms, SPF directory
Workpieces, WKS directory
The default is to back up all cycle directories.
12-270
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
03/2006
Size of the
DRAM area
12 Replacing Software and Hardware
12.4 Standard system start-up via NC card
The amount of DRAM to be reserved for the cycle/program processing from the
DRAM area must be defined in MD 18351: MM_DRAM_FILE_SIZE.
If the DRAM area is too small for the objects to be processed, then the objects
for which there is insufficient space in the DRAM area are saved to the SRAM,
but are still treated as DRAM objects. See below.
Handling of
objects in DRAM
The directories defined in MD 11290: DRAM_FILESYSTEM_MASK are loaded
into the previously cleared DRAM when the control powers up. There they are
part of the passive file system.
When an object is loaded by the MMC/HMI software, the NC also saves it to the
FFS at the same time if the relevant bit for the directory was set in MD 11291:
DRAM_FILESYST_SAVE_MASK. In this way, the object can be made available
once more in DRAM after power up. It should be noted that writing to the FFS is
slow.
Changes to
objects in DRAM
The changes go directly into DRAM as they are made. The changes are not
written to the backed up image in the FFS until the editor is closed.
While they are being saved to the FFS, a sign-of-life symbol is displayed on the
front operating panel (fan blade). To ensure that DRAM objects are not lost
while powering up, the NC must not be switched off until saving to the FFS is
complete.
Deleting SRAM
When the SRAM is deleted, the NCK automatically deletes all the DRAM
backup files in the FFS on the NC card as well. This means that, when a
standard start-up file is read in, none of the old cycles are retained.
12
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
12-271
12 Replacing Software and Hardware
12.4 Standard system start-up via NC card
12.4.2
03/2006
SINUCOPY-FFS
The SINUCOPY-FFS program can be used to write to and read NC cards
for the NCU on a PC with an active PCMCIA slot, both with the SINUMERIK
system software (NC) and with a Flash file system (FFS).
FFS:
Flash file system
A Flash file system is comparable to a DOS data medium. Before data can be
stored, the system must be formatted. Directory structures can then be created
and files can be saved in any format.
The data medium is an electrically erasable EPROM. This means that the
relevant area must be deleted before writing. Algorithms specially matched to
the module identification are required for deleting and writing. They essentially
define the speed at which the data can be written.
An FFS can normally be read directly by DOS/WINDOWS. Since the NC card
also stores the NC system software, which is not present in FFS format, this is
possible only with SINUCOPY-FFS.
Software/hardware
requirement
S The following PCMCIA card drivers/hardware are supported:
–
CSM OMNI97 (external PCMCIA device operated at the parallel interface of the PC)
–
PG740/PG720C (with CSM driver CISIO-S)
–
LAPTOPS with PCMCIA slots (with Intel driver ICARDRV3 – only for
cards up to a max. of 4 MB)
–
CSM PCJB slots (only for cards up to a max. of 4 MB)
S The program runs under Windows 95. Also under Windows NT if CSM
12
OMNI97 is used.
Functions
SINUCOPY-FFS can perform the following functions on the FFS area of the NC
card independently of the SINUMERIK system software (NC):
S read
S modify
S re-write
S re-format
S create new directories
S copy a file to directories and subdirectories
S read and write system SW
S write data to an NC card
12-272
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
12 Replacing Software and Hardware
12.4 Standard system start-up via NC card
03/2006
Expert mode
In Expert mode, and FFS image is generated in the PC memory. This can be
written to the inserted NC card or saved as a file.
Normal mode
In Normal mode, every action (read/write/delete) is carried out directly on the
NC card.
Independently of the FFS, the NC system can be
S re-written (Requirement: the space above the FFS start address is not used
by the NC system).
S duplicated
S output and saved as a file.
S NC cards can be duplicated fully (NC + FFS).
It is possible to display the version of the NC system of the inserted card.
The storage capacity of the inserted NC card is determined automatically and
displayed. Similarly, the limit memory addresses for the FFS.
Operation
The functions of the program can be called via the menu bar or directly by pressing buttons on the user interface. Help is available for all actions and can be
accessed with the “Help” menu.
12
Fig. 12-1
SINUCOPY-FFS operator interface
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
12-273
12 Replacing Software and Hardware
12.4 Standard system start-up via NC card
03/2006
S Display card contents:
Click on the NC card image with the left mouse button (menu: NC card /version display for the NC system)
S Display card info with card and FFS data
Click on a free space (not a button or image, e.g. top right) with the right
mouse button (as for the NC Card/ID Info menu).
S The arrows can be used as menu commands:
–
Read/write NC system. Including read/write FFS system.
–
Copy files from hard disk to the FFS system.
–
Copy files back from the FFS system to the hard disk.
–
Load or store complete FFS systems in RAM image.
S List boxes (Explorer)
On the left of the list boxes are the FFS directories available for selection.
On the right is the content of the selected directory. Double click on the
directory name to select it. Use the “Backspace key” to move up a level.
Before you can use the “Modify file” or “Delete file” button, a file must be
selected in the right list field.
S Info box bottom left
Once the FFS system has been formatted, the Info box at the bottom left
shows the formatted memory, the free space as a % and as a number of
bytes.
Note
Note that the date in the Info field are gross data. Subtract approx. 8% for
overhead.
S FFS system detection
12
If the program is started with a card inserted, it detects whether an FFS
system is supported. If there are no IDs on the card for the FFS start and
end addresses, the system automatically recommends the best ones.
Note
If you change this card, this is detected automatically. The contents of the card
(FFS) are displayed.
12-274
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
12 Replacing Software and Hardware
12.4 Standard system start-up via NC card
03/2006
Installation
1. Start the “sinucopy-ffs.exe” file
2. Enter the password
3. Dialog: Specify a temporary directory for unzipping the files
4. Dialog: Specify the hardware configuration
5. Dialog: Select the components to be installed
6. Dialog: Specify a directory for the installation
7. The SW is installed
8. Message: “driver installed”
9. Dialog: “Select the name of the program folder”
10. Dialog: Please read the README file
11. Dialog: Restart now or later
12. Following restart, you can use the SINUCOPY-FFS function
Tool: ARCEDIT
This tool is intended for use by experts.
S Read archive data
S Delete/insert files
S Modify files (if editable)
Tool: SICARD
This tool is intended for use by experts.
S Read and write NC cards
S Duplicate NC cards
12
Note
1. PG with SINUCOPY (previous version)
The installation can fail if the driver “cisio-s” is entered in the “config.sys” file
and this is detected during power up: error message. Remedy:
–
Delete the line “Device ...cisio.exe, cisio.ini”.
–
Enter a free interrupt number in HEX format in the “cisio.ini” file in the
line IRQ=....
A free interrupt number can be determined via the “System properties”
menu of the “Device manager”.
2. If an NC card with FFS is copied with previous version of SINUCOPY, only
the NC system (not the FFS part) is transferred to the copy.
3. Any drive may be designated for the OMNI97 device: Simply enter the drive
letter in the “Control Panel/Device Manager/Drives/OMNI97” menu.
Windows NT: Enter the drive letter in the “OmniControl/DriveLetter” menu.
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
12-275
12 Replacing Software and Hardware
12.4 Standard system start-up via NC card
Tool: SINUCOPY
03/2006
The SINUCOPY program can be used to
S write to, duplicate and read NC cards for the NCU on a PC with an active
PCMCIA slot and the SINUMERIK system software (NC). The version IDs of
the programs can be displayed (as for the version display for the
SINUMERIK control).
S Data can be read from and written to the PC cards of the PCU with the
SINUMERIK system software (HMI).
S Data from the NC is written to the NC card.
Operation
The functions of the program can be called via the menu bar or directly by pressing buttons on the user interface. Help is available for all actions and can be
accessed with the “Help” menu.
Note
NC data can be written to the NC card; for instructions see:
/BAD/ HMI Advanced User Guide, Services area.
12.4.3
Associated conditions for replacing software
The following NCUs are available for software version 6:
S NCU 571.2
S NCU 572.3
S NCU573.3
12
The following points should be noted during an NC upgrade:
1. If an NCU 5xx with software version 5 is upgraded to version 6, the NCU
must also be replaced with a current NCU that is available for software
version 6.
2. If an NC card equipped with software version 6 is plugged into an earlier
hardware variant (e.g. NCU 572.2), the system will not power up. The status
display flashes in the sequence 0 – 1 – 6.
3. If an NC card equipped with software version 5 is plugged into a current
hardware variant (e.g. NCU 572.3), the system will not power up. The status
display flashes in the sequence 0 – 1 – 6.
4. If an NC card for an NCU 573.2 equipped with software version 5 is plugged
into a current hardware variant (NCU 571.2), the system will power up and
can run.
12-276
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
12 Replacing Software and Hardware
12.6 Replacing batteries and fans
03/2006
12.5
Hardware replacement
You can replace all components that are ordered via a machine-readable
product designation number.
Please save data before removing any hardware component.
Note
The NCU module can be removed from the NCU box without loss of data since
the data is buffered by a capacitor for approx. 15 minutes.
Reference material:
12.6
/PHD/ SINUMERIK 840D Device Manual,
NCUConfiguration
/PJU/ Converter Configuration Manual
/BH/ Operator Components Manual
Replacing batteries and fans
!
Caution
Do not attempt to reactivate discharged batteries by heating them or other
means. The batteries must not be charged as this can lead to leaks and/or
explosion.
Ignoring this instruction may result in injury or damage to property.
Details of the procedure can be found in the following documentation:
Reference material:
12
/PHD/ SINUMERIK 840D Device Manual,
NCUConfiguration
J
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
12-277
12 Replacing Software and Hardware
12.6 Replacing batteries and fans
03/2006
Notes
12
12-278
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
13
HMI
The content of this section can be found in
/IAM/ Start-up Guide for HMI, IM2 and IM4
The HMI Start-up Guide is divided into 6 books:
AE1
Updates/Supplements
BE1
Upgrading the user interface
HE1
Online help
IM2
Starting up HMI Embedded
IM4
Starting up HMI Advanced
TX1
Creating foreign language texts
J
13
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
13-279
03/2006
13 HMI
Notes
13
13-280
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
14
Miscellaneous
14.1
Tool box software package
14.1.1
Contents of the tool box
Content
Supplied on CD-ROM with
S Basic PLC program
S NC variable selector
S Sample programs
S ReadMe file for the current 840D software release
Software
requirements
The following software is required for data communication:
S PCIN software
S SIMATIC Step7 for the PLC programs
Hardware
requirements
Programming device and cable
S Programming device PG/PC
S Cable for V24 PG/PC-NC: 6FX2 002-1AA01-0BF0
S Cable for MPI bus: 6ES7 901-0BF00-0AA0
14.1.2
14
Application of the Tool box
PLC basic
program
Reference material:
NC variable
selector
You will need the NC variable selector to read and write NCK variables.
Reference material:
/FB1/ P3, Function Guide for Basic Machine,
PLC basic program
/LIS2/ Lists, section: Variables
/FB1/ P3, Function Guide for Basic Machine,
PLC basic program
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
14-281
03/2006
14 Miscellaneous
14.2 Machine data access via part program
14.2
Machine data access via part program
Data identifiers
With the HMI, the designation of the machine data is displayed. The internal
data designation requires further identifiers. If the machine data is modified by
programming or read in via the serial port, then these identifiers must be
specified.
Data areas
$MM_
$MN_/$SN_
$MC_/$SC_
$MA_/$SA_
$MD_
Where:
Display machine data (operating panel data)
General machine data/setting data
Channel-specific machine data/setting data
Axis-specific machine data/setting data
Drive machine data
$
System variable
M
Machine data
S
Setting data
M, N, C, A, D
Partial area (second letter)
Axis data is addressed via the axis name. The internal axis designation (AX1,
AX2 ... AX5) or the designation specified via MD 10000: AXCONF_NAME_TAB
may be used as the axis name.
e.g.:
$MA_JOG_VELO[Y1]=2000
The JOG speed of axis Y1 is 2000 mm/min.
If the contents of the machine data is a STRING (e.g. X1) or a hexadecimal
value (e.g. H41), then the content must be given between “ ‘ ” (e.g. ‘X1’ or
‘H41’).
e.g.:
$MN_DRIVE_INVERTER_CODE[0]=‘H14‘
FDD module 9/18 A at drive slot 1 of the drive bus.
To address the various contents of a machine data, identifying data must be
specified in square brackets.
e.g.:
$MA_FIX_POINT_POS[0,X1]=500.000
The 1st fixed point position of
(0=1st, 1=2nd, 2=3rd etc.)
Examples
14
axis X1 is 500
$MN_AUXFU_GROUP_SPEC[2]=‘H41’
Time at which the auxiliary functions of the 3rd auxiliary function group are
output.
$MN_AXCONF_MACHAX_NAME_TAB[0]=‘X1’
Name of the 1st machine axis is X1.
$MA_REF_SET_POS[0,X1]=100.00000
The 1st reference point value of axis X1 is 100 mm.
Assignment of channel-specific machine data:
CHANDATA(1)
Assignment for channel 1
$MC_CHAN_NAME=‘CHAN1’
Channel name for channel 1
$MC_AXCONF_GEOAX_NAME_TAB[1]=‘Y’
Name of the 2nd geometry
axis on channel 1 is Y
...
R10 = 33,75
14-282
R10 of channel 1
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
14 Miscellaneous
14.2 Machine data access via part program
03/2006
...
CHANDATA(2)
Assignment for channel 2
$MC_CHAN_NAME=‘CHAN2‘
Channel name for channel 2
...
R10 = 96,88
R10 of channel 2
...
J
14
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
14-283
14 Miscellaneous
14.2 Machine data access via part program
03/2006
Notes
14
14-284
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Abbreviations
ASCII
American Standard Code for Information Interchange
ASUB
Asynchronous subroutine
BA
Operating mode
BAG
Mode group
BB
Ready
BCD
Binary Coded Decimal
BHG
Hand-held terminal
BOOTFILE
Boot file for SIMODRIVE 611D
CC
Compiler Cycles
CCU
Compact Control Unit
COM
Communication
CPU
Central Processing Unit
CTS
Clear To Send message for serial data interfaces
DAU
Digital-analog converter
DB
Data block
DBB
Data block byte
DBX
Data block bit
DEE
Data terminal
DÜE
Data transmission device
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
A
A
A-285
03/2006
A Abbreviations
A
DPR
Dual-port RAM
DRAM
Dynamic RAM (unbuffered)
DRF
Differential Resolver Function
DRY
Dry Run
DSR
Data Send Ready message from serial data interfaces
DW
Data word
EFP
Simple I/O module (PLC I/O module)
EPROM
Electrically-Programmable Read-Only Memory
ETC
ETC key > Extension to the soft key bar in the same menu
FC
Function Call, function block in the PLC
FEPROM
Flash EPROM: Readable and writable memory
FIFO
First In First Out: memory that works without having to specify an address. The
data is read in the order in which it was saved.
FRK
Cutter radius correction
FST
Feed Stop
FIPO
Fine interpolator
GEO
Geometry
GND
Signal ground (reference point)
GP
Basic program
HASH
A software method for mapping a large number of names onto a finite memory
area
HEX
Abbreviation for hexadecimal number
HMI
Human Machine Interface: SINUMERIK operating function for operation, programming and simulation. The meaning of HMI is identical with MMC.
HSA
Main spindle drive
HW limit switch
Hardware limit switch
A-286
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
A Abbreviations
03/2006
INC
Increment
INI
Initializing data
INTV
Internal duplication
ISO code
Special punched tape code, the number of holes per character is always even
JOG
Jogging: set-up mode
K1
Channel 1
KV
Servo gain factor
KÜ
Speed ratio
K BUS
Communication bus
LED
Light Emitting Diode
LMS1
Position measuring system 1
LMS2
Position measuring system 2
LPFC
Low Priority Frequency Channel
LSB
Least Significant Bit
MD
Machine data
MDA
Manual Data Automatic
MMC
Man Machine Communication: SINUMERIK operating function for operation,
programming and simulation. The meaning of HMI is identical with MMC.
MPF
Main Program File: NC part program (main program)
MPI
Multi-Port Interface
MSTT
Machine control panel
NC
Numerical Control
NCK
Numerical Control Kernel
NCU
Numerical Control Unit
NPFK
Low-priority frequency channel
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
A
A-287
03/2006
A Abbreviations
A
NST
Interface signal
NV
Zero shift
OB
Organizational block in the PLC
OPI
Operator Panel Interface
P-BUS
I/O bus
PCMCIA
Personal Computer Memory Card International Association
PG
Programming device
PLC
Programmable Logic Control
PRT
Program test
RAM
Random-Access Memory (read and write)
ROV
Rapid Override: input correction
RPA
R Parameter Active: Identifier for R-parameters
RTS
Request To Send: switch on transmitter, control signal from serial data
interfaces
SBL
Single Block
SEA
Setting Data Active
SD
Setting data
SK
Soft key
SKP
Skip: hide block
SLM
Synchronous Linear Motor
SPF
Sub Program File
SRAM
Static RAM (buffered)
SSFK
Leadscrew error compensation
SW limit switch
Software limit switch
TEA
Testing Data Active: identifier for machine data
A-288
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
A Abbreviations
03/2006
TO
Tool Offset
TOA
Tool Offset Active: identifier for tool offsets
VSA
Feed drive
V24
Serial interface (definition for the lines used to exchange data between DEE
and DÜE)
VDI
Interface between PLC and NC
WKZ
Tool
WRK
Tool radius offset
WZ
Tool
WZK
Tool offset
WZW
Tool change
ZOA
Zero Offset Active
µC
Micro-controller
J
A
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
A-289
A Abbreviations
03/2006
Notes
A
A-290
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Index
A
C
Absolute encoder
Readjusting, 6-93
Setting up, 6-92
with large traveling range, 6-94
Absolute measuring systems, Parameter settings,
6-92
Acceleration, 6-105
Accessories, 1-13
Actions for PLC general reset, 5-43
Adapting encoders for linear measuring systems,
6-90
Alarm list, 8-169
Alarm numbers, 8-167
Alarm text files, PCU50, 8-164
Alarm text files for HMI Embedded, 8-163
Alarm text files, syntax, 8-167
Alarm texts, 8-163
AM function, 6-154
Analog output, 10-177
Analog output (DAC), 10-216
Archiving by area, 11-233
Assigned inputs/outputs in the PLC for the MSTT,
3-29
Assigning the actual value channels, 6-85
Assigning the setpoint channels, 6-85
Automatic controller settings, 10-217
Axes, 6-78
Axis
Configuration, 6-78
Data, 6-99
Dry run, 9-173
Mode, 6-115
Monitoring, 6-108
Parameter sets, 6-99
Position control data, 6-103
Referencing, 6-113
Types, 6-99
Velocity matching, 6-102
Calculation resolution, 6-70
CCU controls, 5-39
CCU displays, 5-39
Channel level, 6-79
Circularity test, 10-178
Communication equipment, 3-21
Communication parameters, 3-29
Configurable parameter areas for GUD blocks,
6-57
Contour monitoring, 6-111
Control loops, 6-103, 6-106
Converting and transferring, 8-164
Current control loop measurement, 10-223
Cycle alarm texts, 11-229
Cyclical operation, 7-161
B
Back up hard disk, 11-245, 11-247
Backing up modified values, 11-231
BIOS setup, HMI Advanced, 5-47
BTSS
Network rules, 3-19
Settings, 3-19
Bus addresses, 3-26
D
Data back-up
General, 11-227
Standard system start-up, 11-233
Transmission errors, 11-235
via HMI Advanced, 11-229
via HMI Embedded, 11-229
via PG/PC, 11-229
via V24 on PCU 50/70, 11-236
Default configuration, 3-26
Deviation from standard configuration, 3-30
Display on the status display during power-up,
5-45
Display resolution, 6-70
DMP compact modules, 6-78
Documentation, 1-14
Download PLC program, 7-160
Download scaling machine data, 6-76
Download standard machine data, 6-77
Downloading archive data, 11-234
DRAM, 6-73
DRAM for storing cycles, 12-269
Drive configuration, 6-82
Setting, 6-82
Drive optimization, 10-177
Drive parameter settings
4 motor records, 6-87
Non-Siemens motor, 6-88
Drive parameters for optimization, 6-95
Drive test travel request, 10-182
Drives, Power-up, 5-46
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Index-291
Index
03/2006
Dynamic monitoring, Velocity monitoring, 6-111
Dynamic monitoring functions, 6-111
Dynamic RAM memory, 6-73
I
Inch system, 6-67
Incremental measuring systems, parameter
settings, 6-89
Initial start-up, 6-66
Input limits, 6-70
Installing a replacement hard disk, 11-253
Interface for customer’s operating panel, 3-31
Interfaces, 3-31
Switch, 3-31
Interface signals for the measuring system
changeover, 6-101
E
EMC measures, 4-35
Enable
Axis, 9-171
Drive, 9-171
Encoder for several axes, 6-100
Encoder limit frequency, 6-125
Encoder monitoring, 6-111
Error message texts, 11-229
Error while powering up control (NC), 5-45
ESD measures, 4-36
Evaluating line checksums, 11-260
Evaluating machine data numbers , 11-261
Example, Speed ranges for automatic gear step
selection (M40), 6-121
Example: Starting up NCK I/Os, 6-127
Export permits required, 1-14
Export variant 840D, 1-14
K
KV (loop gain) factor, 6-103
L
F
File name, Structure, 11-228
File system, passive, 12-271
Following error compensation (bias control), Startup/activation, 6-107
Fourier analysis, 10-178
Frequency response measurement, 10-183
Function blocks, 7-162
Language-specific nature of the alarm texts,
8-166
Languages, 8-164
Limit switch, 9-172
Line checksums, 11-260
Linear axis
with linear scale, 6-91
with rotary encoder at the machine, 6-90
with rotary encoder at the motor, 6-89
Linear motors , 1FN1, 1FN3, 6-129
Loop gain, 6-103, 6-104, 6-105
M
G
Gantry axes, 10-195
Gear step speed , 6-125
General example for cycle settings, 6-67
Geometry axes, 6-78
Ghost, 11-245
Graphical display, 10-194
H
Hardware limit switches, 6-109
Hardware replacement, 12-277
Hardware requirements, 3-26, 3-28
Heat dissipation, 4-36
HEX machine data, Bit editor, 6-50
Hide machine data , 6-63
HMI
BTSS, 3-33
Language, 3-33
HMI Advanced software upgrade, 12-267
HMI Embedded software upgrade, 12-267
Index-292
Machine axes, 6-78
Machine control panel, Power-up, 5-46
Machine data, 6-49, 11-263
Entering, 6-50
for setpoint/actual values/spindle, 6-117
for SRAM memory breakdown, 6-73
Handling, 6-52
Machine data display filter, 6-61
Selecting, 6-61
Setting, 6-61
Machine data hide filter
Activating group filters, 6-62
Expert mode, 6-63
Vertical soft keys, 6-62
Machine data numbers in MD files, 11-261
Machine level, 6-79
Master language, 8-164
mbdde.ini, 8-164
MD consistency, 6-100
MD display filter, access rights, 6-61
MD hide filter, Display criteria, 6-61
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Index
03/2006
Measuring functions, 10-177, 10-179
Canceling, 10-181
Starting, 10-180
Mechanical system measurement, 10-223
Memory areas, 6-71
Memory configuration, 6-71
Hardware structure, 6-71
Message texts, 8-163
Metric system, 6-67
Monitoring the positioning, 6-108
MPI
Baud rate, 3-28
Bus addresses, 3-28
Default configuration, 3-28
Network rules, 3-19, 3-24
Settings, 3-19
Multiple languages, 8-164
N
NCK general reset, 5-41
NCU controls, 5-38
NCU displays, 5-38
Norton Ghost, 11-245
O
Operator message texts, 11-229
Option data, 6-49
Outputting drive data, V24, 11-239
Outputting HMI data, 11-243
Outputting NC data, 11-240
Outputting PLC data, 11-242
Outputting the initialization program, 11-242
Outputting the standard system start-up file,
11-244
P
Parameter sets, extending, 6-107
Parameter settings for the absolute encoder, 6-92
PCU, 3-33
PCU power up, 5-44
PCU20/PCU50, Setting the MPI interface , 3-34
Physical variables, 6-68
PLC
cyclical operation, 7-161
General reset, 5-42
Memory, 7-160
Module, 7-159
Restart, 5-42
Start-up, 7-159
Starting characteristics, 7-161
Status, 7-161
Status displays, 5-45
PLC basic program, 7-159
Parameter settings, 7-162
PLC user program, 7-159
Position control loop
Reference frequency response, 10-188
Scanning, 10-188
Setpoint step change, 10-189
Position control loop, step height, 10-190
Position setpoint filter, 6-107
Positional deviation feedforward, 6-106
Power section selection, 6-83
Power-on, 5-40
Power-on sequence, 5-40
Power-up, 5-41
System settings, 6-155
Powering up control (NC), 5-45
Program level, 6-79
Programming axis-specific actual values, 6-85
Programming axis-specific setpoints, 6-85
Proportional gain, 10-224
Protection level concept, 6-53
Protection levels, 6-53
R
RAM
dynamic, 6-73
static, 6-73
Redefining protection levels, 6-54
Referencing, 6-113
for incremental measuring system, 6-113
with distance-coded ref. markers, 6-114
Referencing with absolute encoders, 6-114
Replacing batteries, 12-277
Replacing fans, 12-277
Replacing software, Associated conditions,
12-276
Requirements for start-up, Wiring blocks, 5-40
RESET, System settings, 6-156
Reset time, 10-225
Response to canceling while reading in MD,
11-261
Restart, 6-86, 7-161
Restore data backup, 11-245
RI suppression measures, 4-35
Rotary axis
with rotary encoder at the machine, 6-90
with rotary encoder at the motor, 6-90
Rotary encoders, 6-89
Rotor position identification, 6-139
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Index-293
Index
S
Saving measurement results, 10-178
Saving user data, 11-247
Scaling machine data, 6-76
Self-optimization, 10-219
Servo trace, 10-178
Setting data, 6-49, 11-263
Handling, 6-52
Setting drive parameters, 6-87
Shielded signal cables, 4-35
Sign-of-life monitoring, 7-161
Simulation axes, 6-101
Size, DRAM area for cycles, 12-271
Software, 1-13
Software limit switches, 6-109
Software update, 12-265
Software upgrade HMI Advanced, 12-267
Software upgrade HMI Advanced Windows NT,
12-267
Software upgrade, HMI Embedded, 12-267
Special axes, 6-78
Speed control loop, 6-97
Guide frequency response, 10-185
Interference frequency response, 10-185
Measurement, 10-225
Scanning, 10-184
Setpoint and interference variable step
change, 10-186
Speed setpoint curve, 6-105
Spindle
Configuration, 6-117
Data, 6-115
Definition, 6-115
Encoder matching, 6-118
Modes, 6-115
Monitoring, 6-125
Number, 6-115
Parameter sets, 6-116
Positioning, 6-122
Setpoint matching, 6-120
Speed, 6-125
Synchronization, 6-123
Test, 9-175
Velocities, 6-120
Spindles, 6-78
SRAM, 6-74
Deleting, 12-271
Standard application, 3-26
for SINUMERIK 810D, 3-28
Standard files, 8-165
Standard system start-up, 12-267
Standard system start-up or archiving by area,
11-227
Standard variant 840D, 1-14
Start of part program, System settings, 6-157
Index-294
03/2006
Start-up concept, Example, 6-64
Start-up sequence, 5-37
Start-up tool
Frequency response measurement, 10-183
Gantry axes, 10-191
Graphical display, 10-194
Trace function, 10-196
Start-up, required devices and accessories, 1-13
Start-up, linear motors, 6-131
Starting up NCK I/Os, 6-127
Static RAM, 6-73
Storing the text files, 8-164
Structure, 2-17
System data, 6-67
Basic settings, 6-67
Control clock cycles, 6-67
T
Test run requirements, 9-171
Text file for cycle alarm texts, 8-167
Text file for PLC alarm texts, 8-168
Tool box, 14-281
Application, 14-281
Hardware, 14-281
NC variable selector, 14-281
Software, 14-281
Torque control loop
Measuring parameters, 10-183
Scanning, 10-183
Trace, Measurement
activate, 10-201
programming, 10-198
Trace function, 10-196
Creating subdirectories, 10-214
Display function, 10-202
File functions, 10-213
Measuring parameters, 10-199
Operation, 10-197
Print graph, 10-215
Printer settings, 10-215
Signal selection, 10-198
Soft keys, 10-199
Trace function, main screen, 10-198
Travel enable, 10-182
Traversing direction, 6-103
U
U/F function, 6-154
User files, 8-165
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Index
03/2006
V
W
V24 interface settings, 11-237
VALITEK streamer, 11-255
Velocity monitoring, 6-111
Visual inspection, 5-40
Wiring blocks, 5-40
Work area limits, 6-110
J
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
Index-295
Index
03/2006
Notes
Index-296
© Siemens AG 2006 All Rights Reserved
SINUMERIK 840D/810D Start-Up Guide (IADC) – 03/2006 Edition
An
SIEMENS AG
A&D MC MS
Postfach 3180
Recommendations
Corrections
for publication:
D–91050 Erlangen
SINUMERIK 840D/810D
SIMODRIVE 611 digital
Tel. +49 (0) 180 / 5050 – 222 [Hotline]
Fax +49 (0) 9131 / 98 – 63315 [Documentation]
E–Mail: mailto:[email protected]
Manufacturer/Service Documentation
Start–up Guide
From
Order no.:
Edition:
Name
Address of your company/office
Street
Postcode:
Town:
Tel:
/
Telefax:
/
Recommendations and/or Corrections
6FC5297-6AB20-0BP0
03/2006
If you identify any typographical errors
while reading this document, please use
this printed form to let us know.
We would also be grateful for your
suggestions and recommendations for
improvement.
Documentation overview SINUMERIK 840D/840Di/810D (03/2006)
General documentation
SINUMERIK
Brochure
SINUMERIK
840D
840Di
810D
Catalog NC 60 *)
Safety
integrated
Safety Integrated
Application Manual
User documentation
SINUMERIK
840D
840Di
810D
Operating Manual
– HMI Embedded *)
– ShopMill
– ShopTurn
– HT6
SINUMERIK
840D sl
840D
840Di sl
840Di
810D
Operating Manual
– HMI Advanced *)
– Operation compact
SINUMERIK
840D sl
840D
840Di sl
840Di
810D
SINUMERIK
840D sl
840D
840Di sl
840Di
810D
Programming Manual
– Fundamentals *)
– Job planning *)
– Programming compact
– Lists of system variables
– ISO Turning/Milling
SINUMERIK
840D sl
840D
840Di sl
840Di
810D
Programming Manual
– Cycles
– Measuring cycles
Diagnostics
Manual *)
SINUMERIK
840Di
System overview
Manufacturer/service documentation
SINUMERIK
840D
810D
SINUMERIK
840D
840Di
810D
Configuration (HW) *) Equipment Manual
Operator
– 840D
Components *)
– 810D
SINUMERIK
840D sl
840D
840Di sl
840Di
810D
Commissioning
Manual *)
– 840D
– 810D
– HMI
SINUMERIK
840D
840Di
810D
SINUMERIK
840Di
Function Manual
– ShopMill
– ShopTurn
Commissioning
Manual
SINUMERIK
840Di
SINUMERIK
840D
810D
SINUMERIK
840D sl
840D
840Di sl
840Di
810D
Lists
Manual *)
– Part 1
– Part 2
Manufacturer/service documentation
SINUMERIK
840D sl
840D
840Di sl
840Di
810D
SINUMERIK
840D
840Di
810D
SINUMERIK
840D
840Di
810D
Function Manual
Function Manual
Function Manual
– Drive functions
– Remote diagnostics
– Fundamentals *)
– Expansion functions. – Tool management – @Event
– Hydraulic module
– Special functions
– Synchronous actions – Analog module
– ISO dialects
– EMC guidelines
Function Manual
Safety Integrated
Configuration
–Operator interface
OP030
–HMI Embedded
SINUMERIK
840D
810D
MCIS
– Computer Link
– Tool Data Information
– NC Data Management
– NC Data Transfer
– Tool Data Communication
Electronic Documentation
SINUMERIK
SIMODRIVE
Motors
DOCONCD *)
DOCONWEB
*) Recommended minimum scope of documentation

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement