INSTALLATION

INSTRUCTIONS

PARTS LIST

HFL Attachment Kit

P/N 08E02-TA0-100

HFL trim

Accessory

Accessory Hands Free Link

HFL retainer

Application

2008 ACCORD

2 AND 4-DOOR

Template

HFL bracket

Publications No.

AII

38281

Issue Date

NOV 2007

Fuse label

HFL harness

HFL sub harness

Fuse (2A)

7 EPT sealers

(1 Not used)

2 Double-sided tapes A

26 Wire ties

(4 Not used)

Double-faced tape B

(May not be used with some vehicles)

© 2007 American Honda Motor Co., Inc. – All Rights Reserved.

AII 38281 (0711)

08E02-TA0-1001-91

1 of 25

4 Self-tapping screws, 3 x 10 mm

2 Washer screws, 4 x 12 mm

Ground bolt

Clip

2 Bushings

2 Self-tapping screws

Rubber bumper

HFL Kit

P/N 08E00-E10-100

Switch

Control unit

Accessory User’s Information Manual

TOOLS AND SUPPLIES REQUIRED

#2 Phillips screwdriver

Flat-tip screwdriver

Shop towel

Diagonal cutters

Ratchet

10 mm Socket

10 mm Combination wrench

Utility Knife

T15 TORX bit

Felt-tip pen

Tape

Pushpin

Drill

3 mm, 4.5 mm, 9 mm and 10 mm Drill bit

20 mm Hole saw

Wire

Rubber mallet

2 of 25

AII 38281 (0711) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.

Illustration of the HFL Installed on the Vehicle

CONTROL UNIT

HFL HARNESS

SWITCH

3.

Disengage the eight retaining tabs and remove the left and right lens from the roof console.

With long roof console

ROOF

CONSOLE

4 RETAINING

TABS

SHOP

TOWEL

HFL

SUB-HARNESS

INSTALLATION

Customer Information: The information in this

installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by

“do-it-yourselfers.”

1.

Make sure you have the anti-theft code for the audio system or the navigation system (if equipped).

2.

Disconnect the negative cable from the battery.

FLAT-TIP

SCREWDRIVER

With short roof console

LEFT

LENS

RIGHT

LENS

4 RETAINING

TABS

ROOF

CONSOLE

RIGHT

LENS

SHOP

TOWEL

4 RETAINING

TABS

LEFT

LENS

FLAT-TIP

SCREWDRIVER

4 RETAINING

TABS

© 2007 American Honda Motor Co., Inc. – All Rights Reserved.

AII 38281 (0711)

3 of 25

4.

Open the sunglass holder.

5.

Remove the two black screws and the two silver screws and let the roof console drop down.

Disconnect the three vehicle connectors and remove the roof console.

With long roof console

VEHICLE

CONNECTOR

6.

Turn each sunvisor holder 45° counterclockwise, and remove the two sunvisor holders.

SUNVISOR

HOLDER

Turn.

ROOF

CONSOLE

SUNGLASS

HOLDER

Open.

2 SCREWS

(Black)

With short roof console

2 SCREWS

(Silver)

VEHICLE

CONNECTOR

SUNGLASS

HOLDER

Open.

2 SCREWS

(Black)

2 SCREWS

(Silver)

ROOF

CONSOLE

2 SUNVISOR

HOLDERS

7.

Turn the left sunvisor toward the driver’s door.

8.

Locate the slot in the sunvisor holder, and insert a flat-tip screwdriver into the slot. Push in and hold the retaining tab.

HOLDER

FLAT-TIP

SCREWDRIVER

Push and hold tab.

Rotate toward the door.

VEHICLE

CONNECTOR

Disconnect if equipped.

Push upward.

LEFT

SUNVISOR

Turn rearward.

9.

Click To Play Click To Stop

While holding the retaining tab, push up on the left sunvisor holder and turn the left sunvisor back to its original position to remove it. Disconnect the vanity mirror light connector. If the retaining tab does not stay pushed in, return the sunvisor to its original position and repeat steps 7 thru 9.

4 of 25

AII 38281 (0711) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.

2-door model: Do steps 10 and 11.

10. Pull away the weatherstrip from the left front A-pillar trim.

11. Using a small rubber mallet and a shop towel, gently tap the left front A-pillar trim at the “SIDE CURTAIN

AIRBAG” mark to release the clip. Go to step 14.

FRONT A-PILLAR

4-door model: Do steps 12 and 13.

12. Pull away the weatherstrip from the left front A-pillar trim.

13. Using a small rubber mallet and a shop towel, gently tap the left front A-pillar trim just below the “SIDE

CURTAIN AIRBAG” mark to release the clip.

FRONT A-PILLAR

PIN

FRONT A-PILLAR

TRIM

CLIP

STRIKE POINT

SHOP

TOWEL

RUBBER

MALLET

PIN

FRONT

A-PILLAR TRIM

CLIP

STRIKE POINT

SHOP

TOWEL

WEATHERSTRIP

CLIP

LEFT FRONT

A-PILLAR TRIM

WEATHERSTRIP

CLIP

LEFT FRONT

A-PILLAR TRIM

RUBBER

MALLET

© 2007 American Honda Motor Co., Inc. – All Rights Reserved.

AII 38281 (0711)

5 of 25

14.

Remove the left front A-pillar trim (two clips).

LEFT FRONT

A-PILLAR TRIM

2 CLIPS

16. Remove the driver’s dashboard lower cover (eight clips, two hooks, and disconnect the vehicle connector).

VEHICLE

CONNECTOR

DRIVER’S DASHBOARD

LOWER COVER

WEATHERSTRIP

2 HOOKS

15.

Remove and discard the clip on the left front

A-pillar trim, and install a new clip (supplied) on the trim.

NEW CLIP

8 CLIPS

17.

V6 Model only: Remove the driver’s dashboard under cover (three clips and one pin).

3 CLIPS

CLIP (Discard.)

LEFT FRONT

A-PILLAR TRIM

PIN

DRIVER’S DASHBOARD

UNDER COVER

6 of 25

AII 38281 (0711) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.

18. Pull away the weatherstrip, then remove the left dashboard side cover (seven retaining tabs and three hooks).

7 RETAINING

TABS

LEFT DASHBOARD

SIDE COVER

20.

Pull up the front edge of the left front door sill trim (four clips and retaining tab) to remove the trim.

FRONT

4 CLIPS

RETAINING

TAB

3 HOOKS

WEATHERSTRIP

19.

Remove the cover from the trunk lid/fuel fill door opener (two hooks and four retaining tabs), then remove the self-tapping screw. Make sure the trunk lid/fuel opener is unlocked.

LEFT FRONT DOOR

SILL TRIM

21.

Pull away the weatherstrip, then remove the left kick panel (two clips).

WEATHERSTRIP

2 CLIPS

2 HOOKS

SELF TAPPING

SCREW

Unlock.

KEY

FRONT

COVER

4 RETAINING

TABS

TRUNK LID/FUEL

FILL DOOR OPENER

© 2007 American Honda Motor Co., Inc. – All Rights Reserved.

AII 38281 (0711)

LEFT KICK

PANEL

7 of 25

If the vehicle is an M/T model, continue with step 22; if not, go to step 24.

M/T Model

22.

Push down on the shift boot (two retaining tabs).

Remove the shift knob by turning it counterclockwise.

SHIFT KNOB

A/T Model

24. Remove the center console panel (twelve clips and disconnect the vehicle connector).

12 CLIPS

CENTER CONSOLE

PANEL

2 RETAINING

TABS

SHIFT BOOT

Counterclockwise

23. Remove the center console panel (twelve clips and disconnect the vehicle connector). Go to step 25

or 28.

12 CLIPS

CENTER CONSOLE

PANEL

VEHICLE

CONNECTOR

With navigation system, continue with step 25;

Without navigation system go to step 28.

With Navigation System

25. Place a shop towel as shown.

26. Remove the pocket (four bolts).

POCKET

8 of 25

VEHICLE

CONNECTOR

4 BOLTS

SHOP TOWEL

AII 38281 (0711) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.

27. Remove the compact disc changer (two bolts, two clips and disconnect the vehicle connector).

2 CLIPS

VEHICLE

CONNECTOR

Installing the Control Unit and Routing the Harness

If the vehicle is equipped with a Long roof console, continue from step 30; if not, go to step 47.

With long roof console

30. Using a scissors, cut out template A and template B.

Vehicle identification number:

1HG A

TEMPLATE

TEMPLATE A

LINE A

2 BOLTS

COMPACT DISC

CHANGER

Without Navigation System

28. Place a shop towel as shown.

29. Remove the pocket (four bolts).

POCKET

TEMPLATE B

Vehicle identification number:

JHM C

TEMPLATE

TEMPLATE A

LINE B

4 BOLTS

SHOP TOWEL

TEMPLATE B

© 2007 American Honda Motor Co., Inc. – All Rights Reserved.

AII 38281 (0711)

9 of 25

31. Remove the sunglass holder from the roof console

(one screw, one spacer and one spring).

SUNGLASS

HOLDER

33. Remove the console light from the roof console (four retaining tabs).

ROOF

CONSOLE

SPRING

4 RETAINING

TABS

SCREW

(Discard.)

SPACER

(Discard.)

ROOF

CONSOLE

32. Remove the roof console trim from the roof console

(six retaining tabs).

ROOF

CONSOLE

CONSOLE LIGHT

If the vehicle identification number is

1HG A , go to step 34; if not, go to step 35.

34.

While wearing eye protection, enlarge the sunglass holder installation hole on the roof console with a

9 mm drill bit. Make sure to drill at the correct position.

ROOF

CONSOLE

6 RETAINING

TABS

ROOF CONSOLE

TRIM

DRILL BIT

(9 mm)

10 of 25

AII 38281 (0711) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.

35.

Tape template A to the roof console at the indicated position.

ROOF CONSOLE

PUSHPIN

38.

Tape template B to the roof console at the indicated position.

PUSHPIN

FELT-TIP PEN

4 MARKS

TEMPLATE B

TAPE

TEMPLATE A

PUSHPIN

ROOF

CONSOLE

Align.

2 MARKS

TAPE

36. Using a pushpin, mark the roof console as indicated on the template. Remove the template.

37.

While wearing eye protection, drill the two marked locations to 4.5 mm. Remove any burrs.

DRILL BIT

(4.5 mm)

ROOF

CONSOLE

39. Using a pushpin, mark the roof console as indicated on the template. Using a felt-tip pen, mark the roof console around the template. Remove the template.

40. While wearing eye protection, drill the four marked locations to 20 mm. First drill with a 3 mm drill bit and finish with a 20 mm hole saw.

20 mm

HOLE SAW

DRILL BIT

(3 mm)

ROOF

CONSOLE

4 MARKS

DRILL BIT

(3 mm)

20 mm

HOLE SAW

2 MARKS

© 2007 American Honda Motor Co., Inc. – All Rights Reserved.

AII 38281 (0711)

11 of 25

41.

Using an utility knife, cut along the mark made on the roof console in step 39. After cutting, remove any burrs.

ROOF

CONSOLE

Mark made in step 39.

44.

45.

Plug the HFL harness 22-pin connector into the control unit.

Using isopropyl alcohol on a shop towel, clean the areas where the double-sided tapes A will attach.

Remove the adhesive backing from the double-sided tape A and attach the control unit to the roof console as indicated.

CENTER

UTILITY

KNIFE

CONTROL

UNIT

Cut out.

ROOF CONSOLE

42.

Reinstall the console light and trim and unit to the roof console.

43.

Using isopropyl alcohol on a shop towel, clean the areas on the control unit where the double-sided tapes A will attach. Remove the adhesive backing from each double-sided tape A and attach the tape A at the position shown.

Remove the adhesive backing.

2 DOUBLE-SIDED

TAPES A

HFL

HARNESS

HFL HARNESS

22-PIN CONNECTOR

Remove the adhesive backing.

ROOF

CONSOLE

46. Using the holes drilled in step 37, secure the HFL bracket to the roof console. Go to step 67.

ROOF

CONSOLE

CONTROL

UNIT

10 mm

10 mm

Remove the adhesive backing.

2 WASHER

SCREWS,

4 x 12 mm

Holes drilled in step 37.

HFL

BRACKET

12 of 25

AII 38281 (0711) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.

With short roof console

47. Using a scissors, cut out template A and template B.

49. Remove the console light from the roof console (four retaining tabs).

ROOF

CONSOLE

TEMPLATE A

TEMPLATE

LINE C

4 RETAINING

TABS

TEMPLATE B

CONSOLE LIGHT

48. Remove the sunglass holder from the roof console

(two screws, two spacers and one spring).

SUNGLASS

HOLDER

SPRING

If the vehicle identification number is

1HG A , go to step 50; if not, go to step 53.

Vehicle identification number:

1HG A

50.

While wearing eye protection, enlarge the sunglass holder installation hole on the roof console with a 9 mm drill bit. Make sure to drill at the correct position.

ROOF

CONSOLE

SCREW

(Discard.)

SPACER

(Discard.)

SCREW

(Discard.)

SPACER

(Discard.)

ROOF

CONSOLE

DRILL BIT

(9 mm)

© 2007 American Honda Motor Co., Inc. – All Rights Reserved.

AII 38281 (0711)

13 of 25

51. Measure and pierce six locations on the roof console with a pushpin as shown. Drill with a 3 mm drill bit at the six pierced points. Enlarge each hole with a 10 mm drill bit.

5 mm

5 mm

5 mm

CENTER

5 mm

5 mm

5 mm

5 mm

5 mm

5 mm

5 mm 5 mm

ROOF

CONSOLE

5 mm

52. Using a utility knife, cut along the marked line on the roof console as shown. Go to step 55.

Cut.

ROOF

CONSOLE

ROOF

CONSOLE

PUSHPIN

DRILL

DRILL BIT

(3 mm 10 mm)

ROOF

CONSOLE

UTILITY

KNIFE

MARKED LINE

Vehicle identification number:

JHM C

53. Pierce six locations on the roof console with a pushpin as shown. Drill with a 3 mm drill bit at the six pierced points. Then finish with a 10 mm drill bit.

14 of 25

AII 38281 (0711)

PUSHPIN

DRILL

DRILL BIT

(3 mm 10 mm)

© 2007 American Honda Motor Co., Inc. – All Rights Reserved.

54. Using a utility knife, cut along the marked line on the roof console as shown.

57.

While wearing eye protection, drill the two marked locations to 4.5 mm. Remove any burrs.

DRILL BIT

(4.5 mm)

ROOF

CONSOLE

Cut.

ROOF

CONSOLE

ROOF

CONSOLE

UTILITY

KNIFE

MARKED LINE

55.

Tape template A to the roof console at the indicated position.

ROOF

CONSOLE

PUSHPIN

2 MARKS

58.

Tape template B to the roof console at the indicated position.

PUSHPIN

FELT-TIP PEN

4 MARKS

TEMPLATE B

TEMPLATE A

TAPE

Align.

2 MARKS

56. Using a pushpin, mark the roof console as indicated on the template. Remove the template.

© 2007 American Honda Motor Co., Inc. – All Rights Reserved.

AII 38281 (0711)

TAPE

PUSHPIN

ROOF

CONSOLE

59. Using a pushpin, mark the roof console as indicated on the template. Using a felt-tip pen, mark the roof console around the template. Remove the template.

15 of 25

60. While wearing eye protection, drill the four marked locations to 20 mm. First drill with a 3 mm drill bit, then finish with a 20 mm hole saw.

DRILL BIT

(3 mm)

62.

Using isopropyl alcohol on a shop towel, clean the areas where the double-sided tapes A will attach.

Remove the adhesive backing from each double-sided tape A and attach the double-sided tape A at the position shown.

Remove the adhesive backing.

2 DOUBLE-FACE

TAPES A

Remove the adhesive backing.

20 mm

HOLE

SAW

ROOF

CONSOLE

DRILL BIT

(3 mm)

4 MARKS

20 mm

HOLE SAW

61.

Using a utility knife, cut along the mark made on the roof console in step 59. After cutting, remove any burrs.

Mark made in step 59.

ROOF

CONSOLE

CONTROL

UNIT

10 mm

63.

64.

Plug the HFL harness 22-pin connector into the control unit.

Using isopropyl alcohol on a shop towel, clean the areas where the double-sided tapes A will attach.

Remove the adhesive backing from the double-sided tape A and attach the control unit to the roof console as indicated.

HFL HARNESS

HFL HARNESS

22-PIN CONNECTOR

UTILITY

KNIFE

CONTROL

UNIT

Cut out.

ROOF

CONSOLE

CENTER

10 mm

16 of 25

AII 38281 (0711)

Remove the adhesive backing.

ROOF

CONSOLE

CONTROL

UNIT

40 mm

© 2007 American Honda Motor Co., Inc. – All Rights Reserved.

65.

Using isoplopyl alcohol on a shop towel, clean the areas where the double-faced tape B will attach.

attach the double faced tape B to the HFL bracket.

66. With the two 4 x 12 mm washer screws and the holes drilled in step 57, secure the HFL bracket to the roof console.

ROOF

CONSOLE

Switch Installation

67. Bend the switch terminal as shown.

68. Insert the rubber bumper to the HFL retainer.

69. Assemble HFL retainer, switch, and HFL trim with four 3 x 10 mm self-tapping screws.

With long roof console

BACKSIDE OF THE SWITCH

45°

SWITCH

TERMINAL

Bend.

SPEAKER

2 WASHER

SCREWS,

4 x 12 mm

SWITCH

TERMINAL

Holes drilled in step 57.

DOUBLE-FACED TAPE B

HFL TRIM

Remove the adhesive backing.

HFL BRACKET

SWITCH

HFL RETAINER

HFL RETAINER

RUBBER

BUMPER

4 SELF-TAPPING

SCREWS,

3 x 10 mm

© 2007 American Honda Motor Co., Inc. – All Rights Reserved.

AII 38281 (0711)

17 of 25

With short roof console

BACK SIDE OF THE SWITCH

SPEAKER

45°

SWITCH

TERMINAL

Bend.

SWITCH

TERMINAL

HFL TRIM

SWITCH

HFL RETAINER

70.

71.

Reinstall the console light and trim to the roof console.

Connect the HFL harness 20-pin connector to the switch.

With long roof console

SELF-TAPPING

SCREW,

3 x 10 mm

(Black)

SWITCH

CONSOLE

LIGHT

ROOF

CONSOLE

BUSHING

SELF-

TAPPING

SCREW,

3 x 10 mm

(Black)

HFL HARNESS

20-PIN CONNECTOR

With short roof console

SELF-TAPPING

SCREW,

3 x 10 mm

(Black)

HFL

HARNESS

BUSHING

SWITCH

CONSOLE

LIGHT

ROOF

CONSOLE

RUBBER

BUMPER

4 SELF-TAPPING

SCREWS,

3 x 10 mm

BUSHING

BUSHING

HFL RETAINER

HFL HARNESS

20-PIN CONNECTOR

SELF-TAPPING

SCREW,

3 x 10 mm

HFL

HARNESS

(Black)

72.

Install the switch assembly in step 69 to the roof console with two self-tapping screws (Black) and two bushings.

18 of 25

AII 38281 (0711) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.

73.

Wrap two EPT sealers on the HFL subharness

HFL subharness around the corrugated tube.

HFL

SUBHARNESS

END OF THE

CORRUGATED

TUBE

75.

Route the HFL subharness up the A-pillar, and align the green tape on the HFL subharness with the vehicle clip.

ROOF

LINING

VEHICLE CLIP

GREEN

TAPE ON HFL

SUBHARNESS

VEHICLE

HARNESS

WIRE TIE

4 WIRE TIES

HFL SUBHARNESS

LEFT FRONT

A-PILLAR

2 EPT SEALERS

CORRUGATED

TUBE

74.

Attach a piece of wire to the subharness as shown.

Route the subharness up the left front pillar trim opening. Remove the wire.

HFL

SUBHARNESS

LEFT FRONT

PILLAR

OPENING

76.

77.

78.

Secure the HFL subharness to the vehicle harness with one wire tie by the vehicle clip.

Secure the HFL subharness to the vehicle harness with four wire ties.

Route the HFL subharness to the roof console opening.

VEHICLE

BRACKET

DRIVER’S

DASHBOARD

LOWER COVER

OPENING

HFL

SUB-HARNESS

ROOF CONSOLE

OPENING

WIRE

HFL SUBHARNESS

3-PIN CONNECTOR

TAPE

DRIVER’S

DASHBOARD

UNDER COVER

OPENING

ROOF

LINING

© 2007 American Honda Motor Co., Inc. – All Rights Reserved.

AII 38281 (0711)

19 of 25

79.

With an assistant holding the roof console near the roof console opening, plug the HFL harness 3-pin connector into the HFL subharness 3-pin connector, and secure the connector to the vehicle bracket with one wire tie.

WIRE TIE

VEHICLE

BRACKET

81.

Plug the vehicle connectors to the roof console.

Reuse the two screws (black) and the two screws

(silver) to reinstall the roof console.

VEHICLE

CONNECTORS

Front

HFL SUBHARNESS

3-PIN CONNECTOR

ROOF

CONSOLE

GREEN

CONNECTOR

ROOF

CONSOLE

OPENING

HFL HARNESS

3-PIN CONNECTOR

ROOF

CONSOLE

80.

Using isopropyl alcohol on a shop towel, clean the areas where the EPT sealers will attach. Under the roof liner, secure the HFL subharness to the roof panel with three EPT sealers.

2 SCREWS

(Black; Reuse.)

2 SCREWS

(Silver; Reuse.)

82.

Route the HFL subharness down along the vehicle harness forward the fuse box as shown. Secure the

HFL subharness to the vehicle harness with two wire ties.

HFL

SUBHARNESS

VEHICLE

HARNESS

DRIVER’S

DASHBOARD

LOWER COVER

OPENING

3 EPT SEALERS

2 WIRE

TIES

ROOF

LINING

ROOF PANEL

HFL

SUBHARNESS

FUSE

BOX

20 of 25

AII 38281 (0711) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.

83.

Plug the HFL subharness12-pin connector into the fuse box.

FUSE BOX

Front view

FUSE

BOX

84. Remove the upper hood opener bolt, install the ground bolt with the HFL subharness ground terminal into the upper hole of the hood opener, and tighten the ground bolt.

VEHICLE

PANEL

UPPER HOOD

OPENER BOLT

(Discard.)

Connection position

•

HFL SUBHARNESS

12-PIN CONNECTOR

If another accessory is connected to the fuse box 12-pin connector, remove the dummy connector from the 12-pin connector of the other accessory’s harness and connect the

12-pin connector of the HFL subharness to the other accessory’s harness.

FUSE BOX

GROUND

BOLT

(Supplied.)

HFL SUBHARNESS

GROUND TERMINAL

HOOD

OPENER

85.

Secure the HFL subharness to the vehicle harness with two wire ties.

FUSE BOX

VEHICLE

HARNESS

HFL SUBHARNESS

12-PIN CONNECTOR

DUMMY

CONNECTOR

HFL

SUBHARNESS

OTHER ACCESSORY’S

HARNESS 12-PIN

CONNECTOR

OTHER

ACCESSORY’S

HARNESS

2 WIRE

TIES

HFL SUBHARNESS

GROUND TERMINAL

VEHICLE

HARNESS

HFL

SUBHARNESS

© 2007 American Honda Motor Co., Inc. – All Rights Reserved.

AII 38281 (0711)

21 of 25

86. Install the 2A fuse in the fuse box in the location shown.

FUSE BOX

Front view

88.

Route the HFL subharness along the vehicle harness as shown. Loosely secure it to the vehicle harness with three wire ties.

FUSE BOX

VEHICLE HARNESS

HFL

SUBHARNESS

Connection position

FUSE BOX

2A FUSE

87. Attach the HFL 2A fuse label to the kick panel at the location shown.

FUSE LABEL

VEHICLE

HARNESS

3 WIRE TIES

Loosely secure.

89.

Route the HFL subharness along the vehicle harness as shown. Loosely secure it to the vehicle harness with two wire ties.

STEERING TILT LEVER

2A FUSE

LABEL

2A FUSE

LABEL

VEHICLE

HARNESS

STEERING

SHAFT

HFL

SUBHARNESS

2 WIRE TIES

Loosely secure.

22 of 25

AII 38281 (0711) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.

90.

Route the HFL subharness as shown. Loosely secure it to the vehicle harness with three wire ties.

HFL

SUBHARNESS

VEHICLE

BRACKET

92. Disconnect the vehicle harness 1-pin connector, and connect the HFL subharness 1-pin connector.

PARKING BRAKE

VEHICLE

1-PIN

CONNECTOR

ACCELERATOR

PEDAL

3 WIRE TIES

Loosely secure.

VEHICLE

HARNESS

91.

Route the HFL subharness along the vehicle harness. Loosely secure it to the vehicle harness with three wire ties.

HFL

SUB-HARNESS

PARKING

BRAKE

VEHICLE

HARNESS

HFL SUBHARNESS

1-PIN CONNECTOR

VEHICLE HARNESS

1-PIN CONNECTOR

93.

Secure the HFL subharness connections with a wire tie.

HFL

SUBHARNESS

PARKING

BRAKE

LEVER

3 WIRE TIES

Loosely tighten.

WIRE TIE

HFL SUBHARNESS

CONNECTION

© 2007 American Honda Motor Co., Inc. – All Rights Reserved.

AII 38281 (0711)

23 of 25

94. Tighten the three wire ties from step 91.

HFL

SUBHARNESS

PARKING

BRAKE

LEVER

VEHICLE

HARNESS

96.

Tighten the two wire ties from step 89.

STEERING TILT LEVER

WIRE TIE

3 WIRE TIES

95. Tighten the three wire ties from step 90.

VEHICLE

BRACKET

HFL

SUBHARNESS

HFL

SUBHARNESS

VEHICLE

HARNESS

HFL

SUBHARNESS

WIRE TIE

STEERING

COLUMN

VEHICLE

HARNESS

97. Tighten the three wire ties from step 88.

HFL

SUBHARNESS

3 WIRE TIES

VEHICLE HARNESS

VEHICLE

HARNESS

3 WIRE TIES

24 of 25

AII 38281 (0711) © 2007 American Honda Motor Co., Inc. – All Rights Reserved.

98.

Reconnect the vanity mirror light connector,

Insert the holder into the roof panel hole. Push up on the visor and rotate to its original position to lock it into place.

VEHICLE

CONNECTOR

Connect if equipped.

ROOF PANEL

HOLE

LOCK

LEFT SUNVISOR

99. Check that all wire harnesses are routed properly and all connectors are plugged in.

100. Reinstall all removed parts. Check that all clips and other fasteners are installed securely.

101. Reconnect the negative cable to the battery.

102. Enter the customer’s audio system or navigation system (if equipped) anti-theft code.

103. Reset the clock (for vehicles without navigation).

© 2007 American Honda Motor Co., Inc. – All Rights Reserved.

AII 38281 (0711)

25 of 25