Installation Guide N600 Wireless Dual Band Gigabit Router WNDR3700v4 Step 1: Step 2: Unplug the power to turn off your modem. Connect one end of the yellow Ethernet cable to your modem, and the other end to the Internet port on your router. Package Contents (not included) Laptop or desktop computer Step 5: Connect your computer to the router Use another Ethernet cable to establish a wired connection as shown in this diagram. DSL or cable Internet Optionally, connect wirelessly by using the preset wireless security settings, located on the bottom label. Power On/Off Power On/Off Modem Ethernet cable Step 3: Plug in the power to turn on your modem. N600 Wireless Router Power adapter Step 6: N600 Wireless Router Open a browser. Step 4: Wait approximately 2 minutes until your modem turns on. Connect the power adapter to the router, then plug it into an outlet. If your modem has a battery backup, first remove and reinsert the battery before connecting your modem to power. Wait for the 2.4 GHz LED ( to light. 2.4 GHz ) If none of the LEDs light, make sure that the Power On/Off button is in the on position (pushed in). If the web page does not display, close and re-open the browser, then enter http://www.routerlogin.net in the address bar, or check the “Troubleshooting” section on the back of this installation guide. Preset Wireless Security This product has a unique WiFi network name (SSID) and network key (password). The default SSID and password are uniquely generated for every device (like a serial number), to protect and maximize your wireless security. This information is on the label on the bottom of the product. Connect Wireless Devices to Your Router Troubleshooting Choose either the manual or Wi-Fi Protected Setup (WPS) method to add wireless computers, and other devices to your wireless network. The browser cannot display the web page. Manual Method 1. NETGEAR recommends that you do not change the preset SSID or password. If you do change the settings, the information on the bottom of the product does not apply. 2. Open the software utility that manages your wireless connections on the wireless device that you want to connect to your router (iPhone, laptop, computer, gaming device). This utility scans for all wireless networks in your area. Look for the preset NETGEAR wireless network name (SSID), and select it. The SSID is on the product label on the bottom of the router. Note: If you changed the name of your network during the setup process, look for that network name. 3. 4. Find the preset wireless settings on your router and record them here: WiFi network name (SSID) ________________________________ Enter the preset password (or your custom password if you changed it), and click Connect. Repeat steps 1–3 to add other wireless devices. WPS Method If you change the preset wireless settings, record them here: If your wireless device supports WPS (Wi-Fi Protected Setup)—NETGEAR calls this method Push 'N' Connect—you might be prompted to press the WPS button on the router instead of entering a password. If you are prompted to press the WPS button: Wireless network name (SSID) _______________________________ 1. Press the WPS button Network key (password) _____________________________________ 2. Within 2 minutes, press the WPS button on the client device, or follow the WPS instructions that came with your wireless device to complete the WPS process. The device is then connected to your router. If necessary to retrieve or update your password, type http://www.routerlogin.net in a web browser, and log in using the default user name (admin) and password (password). 3. Repeat this process to add other WPS wireless devices. Network key (password) __________________________________ Select Wireless Settings to locate your wireless password. August 2014 on the router. • • • • • Make sure that the computer is connected to one of the four LAN Ethernet ports, or wirelessly to the router. Make sure that the Wireless LED is lit. Close and reopen the browser to make sure that the browser does not cache the previous page. Browse to http://www.routerlogin.net. If the computer is set to a static or fixed IP address (this setting is uncommon), change it to obtain an IP address automatically from the router. Support Thank you for purchasing this NETGEAR product. After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website. For product updates and web support, visit http://support.netgear.com. NETGEAR recommends that you use only the official NETGEAR support resources. You can get the user manual online at http://downloadcenter.netgear.com or through a link in the product’s user interface. For the current EU Declaration of Conformity, visit http://support.netgear.com/app/answers/detail/a_id/11621/. For regulatory compliance information, visit http://www.netgear.com/about/regulatory/. See the regulatory compliance document before connecting the power supply. Get the genie app. Internet WiFi Connection Router Settings STATUS GOOD STATUS Connected Click here Network Map Parental Controls ReadySHARE Number of devices 16 Click here Click here Note: WPS does not support WEP security. If you try to connect a WEP client to your network using WPS, it does not work. Download the free genie app from www.NETGEAR.com/genie. Easily share media, files, and printers on the network from your smartphone, tablet, or laptop. NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice. © NETGEAR, Inc. All rights reserved.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project