HP Pro M1132, Pro M1212nf User guide

HP Pro M1132, Pro M1212nf User guide
LASERJET PROFESSIONAL M1130/M1210
MFP SERIES
User Guide
HP LaserJet Professional M1130/M1210
MFP Series
User Guide
Copyright and License
Trademark Credits
© 2011 Copyright Hewlett-Packard
Development Company, L.P.
Adobe®, Acrobat®, and PostScript® are
trademarks of Adobe Systems Incorporated.
Reproduction, adaptation, or translation
without prior written permission is
prohibited, except as allowed under the
copyright laws.
Intel® Core™ is a trademark of Intel
Corporation in the U.S. and other countries.
The information contained herein is subject
to change without notice.
The only warranties for HP products and
services are set forth in the express warranty
statements accompanying such products and
services. Nothing herein should be
construed as constituting an additional
warranty. HP shall not be liable for technical
or editorial errors or omissions contained
herein.
Part number: CE841-91012
Edition 1, 3/2011
Java™ is a US trademark of Sun
Microsystems, Inc.
Microsoft®, Windows®, Windows® XP,
and Windows Vista® are U.S. registered
trademarks of Microsoft Corporation.
UNIX® is a registered trademark of The
Open Group.
ENERGY STAR and the ENERGY STAR mark
are registered U.S. marks.
Conventions used in this guide
TIP:
Tips provide helpful hints or shortcuts.
NOTE: Notes provide important information to explain a concept or to complete a task.
CAUTION: Cautions indicate procedures that you should follow to avoid losing data or damaging
the product.
WARNING! Warnings alert you to specific procedures that you should follow to avoid personal
injury, catastrophic loss of data, or extensive damage to the product.
ENWW
iii
iv
Conventions used in this guide
ENWW
Table of contents
1 Product basics .................................................................................................................. 1
Product comparison .................................................................................................................. 2
Environmental features .............................................................................................................. 3
Product features ....................................................................................................................... 4
Product views .......................................................................................................................... 6
Front view ................................................................................................................ 6
Back view ................................................................................................................ 8
Serial number and model number location ................................................................. 10
Control-panel layout ................................................................................................ 11
2 Control panel menus (M1210 Series only) ....................................................................... 13
Control-panel menus ............................................................................................................... 14
3 Software for Windows ................................................................................................... 23
Supported operating systems for Windows ................................................................................ 24
Printer driver .......................................................................................................................... 24
Priority for print settings .......................................................................................................... 24
Change printer-driver settings for Windows ............................................................................... 25
Change the settings for all print jobs until the software program is closed ....................... 25
Change the default settings for all print jobs ............................................................... 25
Change the product configuration settings .................................................................. 25
Remove software for Windows ................................................................................................ 25
Supported utilities for Windows ............................................................................................... 27
HP Toolbox software ............................................................................................... 27
HP Embedded Web Server (M1210 Series only) ........................................................ 27
Other Windows components and utilities ................................................................... 27
4 Use the product with Mac ............................................................................................... 29
Software for Mac ................................................................................................................... 30
Supported operating systems for Macintosh ................................................................ 30
Supported printer drivers for Macintosh ..................................................................... 30
ENWW
v
Remove software for Mac ......................................................................................... 30
Priority for print settings for Macintosh ....................................................................... 30
Change printer-driver settings for Mac ....................................................................... 31
Print with Mac ....................................................................................................................... 32
Create and use printing presets with Mac .................................................................. 32
Resize documents or print on a custom paper size with Mac ........................................ 32
Print a cover page with Mac ..................................................................................... 33
Print multiple pages on one sheet of paper with Mac ................................................... 33
Print on both sides (duplex) with Mac ........................................................................ 34
Fax with Mac (M1210 Series only) .......................................................................................... 36
Scan with Mac ...................................................................................................................... 37
5 Connect the product ........................................................................................................ 39
Supported network operating systems ....................................................................................... 40
Printer sharing disclaimer ......................................................................................... 40
Connect with USB .................................................................................................................. 41
CD installation ........................................................................................................ 41
HP Smart Install ....................................................................................................... 41
Connect to a network (M1210 Series only) ............................................................................... 42
Supported network protocols .................................................................................... 42
Install the product on a wired network ....................................................................... 42
Configure network settings ....................................................................................... 43
6 Paper and print media ................................................................................................... 45
Understand paper use ............................................................................................................ 46
Special paper guidelines .......................................................................................... 46
Change the printer driver to match the paper type and size ........................................................ 48
Supported paper sizes ............................................................................................................ 49
Supported paper types ........................................................................................................... 50
Load paper trays .................................................................................................................... 51
Load the input tray .................................................................................................. 51
Tray adjustment for short media ................................................................................ 52
Load the document feeder (M1210 Series only) .......................................................... 54
Tray and bin capacity .............................................................................................. 55
Paper orientation for loading trays ............................................................................ 55
Configure trays ...................................................................................................................... 56
Change the default paper-size setting (M1130 Series) ................................................. 56
Change the default paper-size setting (M1210 Series) ................................................. 57
Change the default paper-type setting (M1130 Series) ................................................ 57
Change the default paper-type setting (M1210 Series) ................................................ 57
vi
ENWW
7 Print tasks ...................................................................................................................... 59
Cancel a print job .................................................................................................................. 60
Print with Windows ................................................................................................................ 61
Open the printer driver with Windows ....................................................................... 61
Get help for any printing option with Windows .......................................................... 61
Change the number of print copies with Windows ...................................................... 62
Print colored text as black with Windows ................................................................... 62
Save custom print settings for reuse with Windows ...................................................... 63
Improve print quality with Windows .......................................................................... 65
Print on preprinted letterhead or forms with Windows .................................................. 66
Print on special paper, labels, or transparencies with Windows .................................... 68
Print the first or last page on different paper with Windows .......................................... 69
Scale a document to fit page size ............................................................................. 71
Add a watermark to a document with Windows ......................................................... 72
Print on both sides (duplex) with Windows ................................................................. 73
Create a booklet with Windows ................................................................................ 75
Use HP ePrint .......................................................................................................... 76
Print multiple pages per sheet with Windows .............................................................. 79
Select page orientation with Windows ....................................................................... 81
8 Copy .............................................................................................................................. 83
Use copy functions ................................................................................................................. 84
One-touch copy ...................................................................................................... 84
Multiple copies ....................................................................................................... 84
Copy a multiple-page original .................................................................................. 85
Copy identification cards (M1210 Series only) ........................................................... 85
Cancel a copy job .................................................................................................. 86
Reduce or enlarge a copy image .............................................................................. 86
Collate a copy job .................................................................................................. 89
Copy settings ......................................................................................................................... 89
Change copy quality ............................................................................................... 89
Copy on both sides (duplex) .................................................................................................... 94
Copy a two-sided original to a one-sided document .................................................... 94
Copy a two-sided original to a two-sided document ..................................................... 94
9 Scan ............................................................................................................................... 97
Use scan functions .................................................................................................................. 98
Scan methods ......................................................................................................... 98
Cancel a scan ...................................................................................................... 100
Scan settings ....................................................................................................................... 101
ENWW
vii
Scan file format .................................................................................................... 101
Scanner resolution and color .................................................................................. 101
Scan quality ......................................................................................................... 103
10 Fax (M1210 Series only) ............................................................................................. 105
Fax features ........................................................................................................................ 106
Set up fax ........................................................................................................................... 107
Install and connect the hardware ............................................................................. 107
Configure fax settings ............................................................................................ 111
Use the HP Fax Setup Wizard ................................................................................ 113
Use the phone book ............................................................................................................. 114
Use the control panel to create and edit the fax phone book ...................................... 114
Import or export Microsoft Outlook contacts into the fax phone book ........................... 114
Use phone-book data from other programs ............................................................... 114
Delete phone book ................................................................................................ 115
Set fax settings ..................................................................................................................... 116
Send fax settings ................................................................................................... 116
Receive fax settings ............................................................................................... 120
Set fax polling ...................................................................................................... 126
Use fax ............................................................................................................................... 127
Fax software ......................................................................................................... 127
Cancel a fax ........................................................................................................ 127
Delete faxes from memory ...................................................................................... 127
Use fax on a DSL, PBX, or ISDN system ................................................................... 128
Use fax on a VoIP service ....................................................................................... 129
Fax memory ......................................................................................................... 129
Send a fax ........................................................................................................... 129
Receive a fax ........................................................................................................ 136
Solve fax problems ............................................................................................................... 138
Fax troubleshooting checklist .................................................................................. 138
Fax error messages ............................................................................................... 139
Fax logs and reports .............................................................................................. 145
Change error correction and fax speed ................................................................... 147
Problems sending faxes .......................................................................................... 148
Problems receiving faxes ........................................................................................ 151
Regulatory information and warranties ................................................................................... 154
11 Manage and maintain the product .............................................................................. 155
Print information pages ......................................................................................................... 156
Use the HP Toolbox software ................................................................................................. 159
View HP Toolbox software ..................................................................................... 159
viii
ENWW
Status .................................................................................................................. 160
Fax (M1210 Series only) ....................................................................................... 160
Shop for Supplies .................................................................................................. 163
Other Links ........................................................................................................... 163
Use the HP Embedded Web Server (M1210 Series only) .......................................................... 164
Open the HP Embedded Web Server ...................................................................... 164
Features ............................................................................................................... 165
Product security features ........................................................................................................ 166
Lock the formatter .................................................................................................. 166
Economy settings ................................................................................................................. 167
Print with EconoMode ............................................................................................ 167
Auto-Off mode ...................................................................................................... 167
Manage supplies and accessories .......................................................................................... 169
Print when a cartridge reaches estimated end of life .................................................. 169
Manage print cartridges ........................................................................................ 169
Replacement instructions ........................................................................................ 170
Clean the product ................................................................................................................ 182
Clean the pickup roller ........................................................................................... 182
Clean the separation pad ....................................................................................... 186
Clean the paper path ............................................................................................ 189
Clean the print-cartridge area ................................................................................. 191
Clean the exterior ................................................................................................. 194
Clean the scanner glass strip and platen .................................................................. 194
Product updates ................................................................................................................... 196
12 Solve problems ........................................................................................................... 197
Solve general problems ........................................................................................................ 198
Troubleshooting checklist ........................................................................................ 198
Factors that affect product performance ................................................................... 199
Restore the factory-set defaults (M1210 Series only) ................................................................. 199
Interpret control-panel light patterns (M1130 Series only) .......................................................... 200
Interpret control-panel messages (M1210 Series only) .............................................................. 203
Control-panel message types .................................................................................. 203
Control-panel messages ......................................................................................... 203
Clear jams .......................................................................................................................... 206
Common causes of jams ........................................................................................ 206
Jam locations ........................................................................................................ 207
Clear jams from the document feeder (M1210 Series only) ........................................ 208
Clear jams from the output areas ............................................................................ 209
Clear jams from the input tray ................................................................................. 211
Clear jams from inside the product .......................................................................... 213
ENWW
ix
Change the jam recovery setting ............................................................................. 214
Solve paper-handling problems .............................................................................................. 216
Solve image-quality problems ................................................................................................ 218
Print-quality examples ............................................................................................ 218
Repetitive defects ruler ........................................................................................... 224
Optimize and improve image quality ....................................................................... 225
Solve performance problems ................................................................................................. 227
Solve connectivity problems ................................................................................................... 227
Solve direct-connect problems ................................................................................. 227
Solve network problems ......................................................................................... 228
Solve software problems ....................................................................................................... 229
Solve common Windows problems ......................................................................... 229
Solve common Mac problems ................................................................................. 229
Appendix A Supplies and accessories .............................................................................. 233
Order parts, accessories, and supplies ................................................................................... 234
Part numbers ....................................................................................................................... 234
Paper-handling accessories .................................................................................... 234
Print cartridges ...................................................................................................... 234
Cables and interfaces ............................................................................................ 234
Appendix B Service and support ...................................................................................... 235
Hewlett-Packard limited warranty statement ............................................................................. 236
HP's Premium Protection Warranty: LaserJet print cartridge limited warranty statement .................. 237
End User License Agreement .................................................................................................. 238
Customer self-repair warranty service ..................................................................................... 240
Customer support ................................................................................................................. 240
Repack the product .............................................................................................................. 241
Service information form ....................................................................................................... 242
Appendix C Specifications ................................................................................................ 245
Physical specifications .......................................................................................................... 246
Power consumption, electrical specifications, and acoustic emissions .......................................... 246
Environmental specifications .................................................................................................. 246
Appendix D Regulatory information ................................................................................ 247
FCC regulations ................................................................................................................... 248
Environmental product stewardship program ........................................................................... 248
Protecting the environment ...................................................................................... 248
Ozone production ................................................................................................. 248
x
ENWW
Power consumption ............................................................................................... 248
Toner consumption ................................................................................................ 249
Paper use ............................................................................................................. 249
Plastics ................................................................................................................. 249
HP LaserJet print supplies ....................................................................................... 249
Return and recycling instructions ............................................................................. 249
Paper .................................................................................................................. 250
Material restrictions (M1130 Series) ........................................................................ 250
Material restrictions (M1210 Series) ........................................................................ 250
Disposal of waste equipment by users in private households in the European Union ...... 251
Chemical substances ............................................................................................. 251
Material Safety Data Sheet (MSDS) ......................................................................... 251
For more information ............................................................................................. 252
Declaration of conformity (base model) ................................................................................... 253
Declaration of conformity (fax model) ..................................................................................... 254
Safety statements ................................................................................................................. 255
Laser safety .......................................................................................................... 255
Canadian DOC regulations .................................................................................... 255
Power cord instructions .......................................................................................... 255
EMC statement (Korea) .......................................................................................... 255
Laser statement for Finland ..................................................................................... 256
GS statement (Germany) ........................................................................................ 256
Substances Table (China) ....................................................................................... 257
Restriction on Hazardous Substances statement (Turkey) ............................................. 257
Additional statements for telecom (fax) products ....................................................................... 258
EU Statement for Telecom Operation ....................................................................... 258
New Zealand Telecom Statements ........................................................................... 258
Additional FCC statement for telecom products (US) .................................................. 258
Telephone Consumer Protection Act (US) .................................................................. 259
Industry Canada CS-03 requirements ...................................................................... 259
Vietnam Telecom wired marking for ICTQC Type approved products .......................... 260
Index ............................................................................................................................... 261
ENWW
xi
xii
ENWW
1
ENWW
Product basics
●
Product comparison
●
Environmental features
●
Product features
●
Product views
1
Product comparison
The product is available in the following configurations.
M1210 Series
M1130 Series
2
●
Prints letter-size pages at speeds up to 19 pages per
minute (ppm) and A4-size pages at speeds up to
18 ppm.
●
Prints letter-size pages at speeds up to 19 pages per
minute (ppm) and A4-size pages at speeds up to
18 ppm.
●
The input tray holds up to 150 sheets of print media or
up to 10 envelopes.
●
The input tray holds up to 150 sheets of print media or
up to 10 envelopes.
●
The output bin holds up to 100 sheets
●
The output bin holds up to 100 sheets
●
2-digit LED control-panel display
●
LCD control-panel display
●
Manual two-sided (duplex) printing and copying.
●
●
Copy from the flatbed scanner
Manual two-sided (duplex) printing, fax receiving, and
copying.
●
Full-color scanning
●
Copy from the flatbed scanner or from the document
feeder
●
Hi-Speed USB 2.0 port.
●
Full-color scanning
●
8-MB random-access memory (RAM).
●
Hi-Speed USB 2.0 port.
●
Integrated networking for connecting to a 10/100BaseTX network.
●
V.34 fax modem and 4-megabyte (MB) flash fax-storage
memory.
●
Two RJ-11 fax/phone cable ports.
●
64-MB random-access memory (RAM).
●
35-page document feeder.
Chapter 1 Product basics
ENWW
Environmental features
Print multiple pages per sheet
Save paper by printing two or more pages of a document side-by-side on one sheet of paper.
Access this feature through the printer driver.
Recycling
Reduce waste by using recycled paper.
Recycle print cartridges by using the HP return process.
Energy savings
Save energy by initiating Auto-off mode for the product.
HP Smart Web printing
Use HP Smart Web printing to select, store, and organize text and graphics from multiple
Web pages and then edit and print exactly what you see onscreen. It gives you the control
you need for printing meaningful information while minimizing waste.
Download HP Smart Web printing from this Web site: www.hp.com/go/smartwebprinting.
ENWW
Environmental features
3
Product features
Print
Copy
Scan
Fax (M1210 Series only)
Supported operating
systems
Memory
Paper handling
Printer driver features
Interface connections
4
Chapter 1 Product basics
●
Prints letter-size pages at speeds up to 19 ppm and A4-size pages at speeds up to
18 ppm.
●
Prints at 400x2 dots per inch (dpi) with FastRes 600 (default). Supports FastRes 1200 for
high-quality printing of text and graphics.
●
Includes adjustable settings to optimize print quality.
●
Scans at 300 pixels per inch (ppi) and prints with FastRes 600.
●
Easily change the number of copies, adjust the lightness or darkness, or reduce or
enlarge the size of copies from the control panel.
●
Provides up to 1200 pixels per inch (ppi) full-color scanning from the flatbed scanner.
●
Provides up to 300 ppi full-color scanning from the document feeder.
●
Scan from TWAIN-compliant or Windows Imaging Application (WIA)-compliant software.
●
Scan from a computer by using HP LaserJet Scan software for Windows or by using
HP Director software for Mac.
●
Full-functionality fax capabilities with a V.34 fax; includes a phone book and delayed-fax
features.
●
Stores up to 500 pages in memory.
●
Recovers faxes from memory for up to four days following a power failure.
●
Windows 7
●
Windows Vista (32-bit and 64-bit)
●
Windows XP (32-bit and 64-bit)
●
Mac OS X 10.4, 10.5, 10.6
●
M1130 Series: Includes 8-megabyte (MB) random-access memory (RAM).
●
M1210 Series: Includes 64-MB RAM.
●
The input tray holds up to 150 sheets of paper or 10 envelopes.
●
The document feeder holds up to 35 sheets of paper.
●
The output bin holds up to 100 sheets of paper.
●
Print multiple pages on one sheet.
●
Print booklets.
●
Scale to fit different paper sizes.
●
Print cover pages on different paper.
●
Hi-Speed USB 2.0 port.
●
RJ-45 network port. (M1210 Series only)
●
Two RJ-11 fax/phone cable ports. (M1210 Series only)
ENWW
Economical printing
ENWW
●
N-up printing (printing more than one page on a sheet) and the manual two sided
printing features save paper.
●
EconoMode printer driver feature saves toner.
Archive printing
Archive printing feature for printing pages that you plan to store for a long time.
Supplies
●
Authentication for genuine HP print cartridges.
●
Easy ordering for replacement supplies.
●
Supplies status page shows estimated toner level in the print cartridge. Not available for
non-HP supplies.
Self-help
Quick-reference pages available from www.hp.com/support/ljm1130series or www.hp.com/
support/ljm1210series.
Accessibility
●
All doors and covers can be opened by using one hand.
Security
●
Receptacle for a cable-type security lock.
Product features
5
Product views
Front view
M1130 Series
1
2
3
4
5
8
7
6
1
Scanner lid
2
Scanner assembly
3
Output bin with extension for long paper
4
Print-cartridge door lift-tab
5
Input tray
6
Short media extender tool
7
Power button
8
Control panel
Chapter 1 Product basics
6
ENWW
M1210 Series
1
2
3
4
5
6
7
10
ENWW
1
Document feeder
2
Document feeder output bin
3
Scanner lid
4
Scanner assembly
5
Output bin with extension for long paper
6
Print-cartridge door lift-tab
7
Input tray
8
Short media extender tool
9
Power button
10
Control panel
9
8
Product views
7
Back view
M1130 Series
1
2
3
8
1
Slot for a cable-type security lock
2
Hi-Speed USB 2.0 port
3
Power connection
Chapter 1 Product basics
ENWW
M1210 Series
2
1
3
4
5
ENWW
1
Slot for a cable-type security lock
2
RJ-45 network port
3
Hi-Speed USB 2.0 port
4
RJ-11 fax ports
5
Power connection
Product views
9
Serial number and model number location
The serial number and product model number label is at the back of the product.
10
Chapter 1 Product basics
ENWW
Control-panel layout
M1130 Series
2
3 4 5
1
6
7
11 10 9
8
1
LED display screen: Displays the number of copies, the level of darkness for copies, and the percentage of copysize reduction or enlargement. It also shows error codes that alert you of problems that require attention.
2
Up and down arrows: Increases or decreases the number of copies, the level of darkness for copies, or the
percentage of copy-size reduction or enlargement.
●
Press the buttons for less than one second to increase or decrease copy settings by one increment.
●
Press the buttons for one second or longer to increase or decrease the level of darkness to the maximum or
minimum value.
●
Press the buttons for one second or longer to increase or decrease the number of copies or the percentage of
copy-size reduction or enlargement by 10 increments.
3
Reduce/Enlarge copy light: Indicates the copy-size reduction or enlargement feature is active.
4
Darker/Lighter copy light: Indicates the copy-darkness feature is active.
5
Number Of Copies light: Indicates the number-of-copies feature is active.
6
Setup button: Scrolls between the copy settings for number of copies, darkness, and copy size for each job. The
default option is the number of copies. To change the default settings for all jobs, scroll to the setting and then press
and hold the button for 3 seconds. When the light is blinking, adjust the setting. Press this button again to save the
setting.
7
Start Copy button: Starts a copy job.
8
Cancel button: Cancels the current job, or clears the last setting you made. When the product is in the Ready
state, press this button to reset the copy settings to the default values.
9
Toner-level status light: Indicates the level of toner in the print cartridge is low.
10
Attention light: Indicates a problem with the product.
11
Ready light: Indicates the product is ready or is processing a job.
ENWW
Product views
11
M1210 Series
4
5
6
7
3
2
1
8
9
10
15
12
14
13
12 11
1
Toner-level status light: Indicates the level of toner in the print cartridge is low.
2
Attention light: Indicates a problem with the product. View the LCD display for a message.
3
Ready light: Indicates the product is ready or is processing a job.
4
LCD display screen: Displays status information, menus, and messages.
5
Copy Settings button: Opens the Copy Settings menu. To copy an identification card, press this button three
times to open the Copy ID menu and then press the OK button.
6
Setup button: Opens the menus.
7
Left and right arrows: Enter and navigate through the menus. Decrease or increase the current value on the
screen. Move the screen cursor backward or forward one space.
8
OK button: Acknowledges a setting or confirms an action to proceed.
9
Cancel button: Cancels the current job, or clears the last setting you made. When the product is in the Ready
state, press this button to reset the copy settings to the default values.
10
Start Copy button: Starts a copy job.
11
Back arrow: Returns to the previous level in the menus.
12
Send Fax button: Starts a fax job.
13
Redial button: Recalls the last digits used for the previous fax job.
14
Darker/Lighter copy button: Adjusts the darkness setting for the current copy job.
15
Numeric keypad: Use the keypad to enter fax numbers or to enter data.
Chapter 1 Product basics
ENWW
2
Control panel menus (M1210 Series
only)
●
ENWW
Control-panel menus
13
Control-panel menus
These menus are available from the control-panel main menu:
●
Use the Phone Book menu to open the list of entries in the fax phone book.
●
Use the Fax Job status menu to display a list of all faxes that are waiting to be sent, or have
been received but are waiting to be printed, forwarded, or uploaded to the computer.
●
Use the Fax functions menu to configure fax functions such as scheduling a delayed fax,
cancelling the Receive to PC mode, reprinting faxes that were previously printed, or clearing
faxes that are stored in memory.
●
Use the Copy setup menu to configure basic copy default settings such as contrast, collation, or
the number of copies printed.
●
Use the Reports menu to print reports that provide information about the product.
●
Use the Fax setup menu to configure the outgoing and incoming fax options and the basic
settings for all faxes.
●
Use the System setup menu to establish basic product settings such as language, print quality,
or volume levels.
●
Use the Service menu to restore default settings, clean the product, and activate special modes
that affect print output.
●
Use the Network config. menu to establish network configuration settings.
Table 2-1 Phone Book menu
Menu item
Sub-menu item
Description
Phone Book
Add/Edit
Edits the fax phone book. The product supports up to 100 phone book entries.
Delete
Delete all
Table 2-2 Fax Job status menu
Menu item
Description
Fax Job status
Displays pending fax jobs, and allows you to cancel pending fax jobs.
Table 2-3 Fax functions menu
14
Menu item
Description
Send fax later
Allows a fax to be sent at a later time and date.
Chapter 2 Control panel menus (M1210 Series only)
ENWW
Table 2-3 Fax functions menu (continued)
Menu item
Description
Stop Recv to PC
Disables the Receive to PC setting that allows a computer to upload all current faxes that have
not been printed and all future faxes received by the product.
Reprint last
Reprints the faxes that are stored in the product memory.
Polling receive
Allows the product to call another fax machine that has polling send enabled.
Clear saved faxs
Clears all faxes in the product memory.
Table 2-4 Copy setup menu
Menu item
Sub-menu item
Description
Default Quality
Text
Sets the default copy quality.
Draft
Mixed
Film photo
Picture
Def. light/dark
Sets the default contrast option.
Def. Collation
Off
Sets whether copies are collated as they are printed.
On
Def. # of copies
(Range: 1-99)
Sets the default number of copies.
Def. Reduce/Enlrg
Original=100%
Sets the default percentage to reduce or enlarge a copied
document.
A4 to Letter=94%
Letter to A4=97%
Full Page=91%
2 pages per sheet
4 pages per sheet
Custom: 25 to 400%
Table 2-5 Reports menu
Menu Item
Demo page
ENWW
Sub-menu item
Sub-menu item
Description
Prints a page that demonstrates print quality.
Control-panel menus
15
Table 2-5 Reports menu (continued)
Menu Item
Sub-menu item
Sub-menu item
Description
Fax Reports
Fax Confirmation
Never
Sets whether or not the product prints a confirmation
report after a successful sending or receiving job.
Send fax only
Receive fax
Every fax
Fax Error report
Every error
Send error
Sets whether or not the product prints a report after a
failed sending or receiving job.
Receive error
Never
Last Call report
Include 1st page
Prints a detailed report of the last fax operation, either
sent or received.
On
Off
Fax Activity log
Print log now
Auto Log Print
Sets whether or not the product includes a thumbnail
image of the first page of the fax on the report.
Print log now: Prints a list of the last 40 faxes that
have been sent from or received by this product.
Auto Log Print: Select On to automatically print a
report after every 40 fax jobs. Select Off to turn off the
automatic print feature.
Phone Book report
Prints a list of the phone book entries that have been set
up for this product.
Block Fax list
Prints a list of phone numbers that are blocked from
sending faxes to this product.
All fax reports
Prints all fax-related reports.
Menu structure
Prints a control-panel menu layout map. The active
settings for each menu are listed.
Config report
Prints a list of all the product settings, including the
network and fax settings.
Supplies Status
Prints information about the print cartridge, including
the estimated number of pages remaining and the
number of pages printed.
Table 2-6 Fax setup menu
Menu Item
Sub-menu item
Fax header
Your fax
number
Sub-menu item
Description
Sets the identifying information that is sent to the receiving
product.
Company name
16
Chapter 2 Control panel menus (M1210 Series only)
ENWW
Table 2-6 Fax setup menu (continued)
Menu Item
Sub-menu item
Sub-menu item
Description
Fax Send setup
Def. Resolution
Fine
Sets the resolution for sent documents. Higher resolution
images have more dots per inch (dpi), so they show more
detail. Lower resolution images have fewer dots per inch
and show less detail, but the file size is smaller.
Superfine
Photo
Standard
Def. light/dark
Def. Glass size
Sets the darkness of outgoing faxes.
Letter
A4
Dialing Mode
Changing the resolution setting might affect the fax speed.
Tone
Sets the default paper size to use when scanning and
copying from the flatbed glass.
Sets whether the product should use tone or pulse dialing.
Pulse
Redial if busy
On
Off
Redial-no
answer
On
Redial Comm.
Error
On
Dial Prefix
On
Off
Off
Off
Detect dial tone
On
Off
Fax Recv. setup
Answer mode
Automatic
TAM
Fax/Tel
Manual
ENWW
Sets whether or not the product should attempt to redial if
the line is busy.
Sets whether the product should attempt to dial if the
recipient fax number does not answer.
Sets whether the product should attempt to redial the
recipient fax number if a communication error occurs.
Specifies a prefix number that must be dialed when sending
faxes from the product.
Sets whether the product should check for a dial tone
before sending a fax.
Sets the type of answer mode. The following options are
available:
●
Automatic: The product automatically answers an
incoming call on the configured number of rings.
●
TAM: Use this setting when a telephone answering
machine is connected to the product. The product does
not automatically answer the call. Instead, it waits until
it detects the fax tone.
●
Fax/Tel: The product answers incoming calls
immediately. If it detects the fax tone, it processes the
call as a fax. If it does not detect the fax tone, it
creates an audible ring to alert you to answer the
incoming voice call.
●
Manual : You must press the Send Fax
button or
use an extension phone to make the product answer
the incoming call.
Control-panel menus
17
Table 2-6 Fax setup menu (continued)
Menu Item
Sub-menu item
Sub-menu item
Rings to answer
Answer Ring
Type
Description
Sets the number of rings that must occur before the fax
modem answers.
All Rings
Single
Allows you to have two or three phone numbers on a single
line, each with a different ring pattern (on a phone system
with distinctive-ring service).
Double
●
All Rings: The product answers any calls that come
through the telephone line.
●
Single: The product answers any calls that produce a
single-ring pattern.
●
Double: The product answers any calls that produce
a double-ring pattern.
●
Triple: The product answers any calls that produce a
triple-ring pattern.
●
Double&Triple: The product answers any calls that
produce a double-ring or triple-ring pattern.
Triple
Double&Triple
Extension Phone
On
Off
Silence detect
On
Off
Fit to page
On
Off
Stamp faxes
On
Off
Forward fax
On
Off
Block faxes
Add entry
Delete entry
Clear all
Reprint faxes
On
Off
18
Chapter 2 Control panel menus (M1210 Series only)
When this feature is enabled, you can press the 1-2-3
buttons on the extension phone to cause the product to
answer an incoming fax call.
Sets whether the product can receive faxes from older
model fax machines that do not emit the initial fax tones
used during fax transmission.
Shrinks faxes that are larger than Letter-size or A4-size so
that they can fit onto a Letter-size or A4-size page. If this
feature is set to Off, faxes larger than Letter or A4 will print
on multiple pages.
Sets product to add the date, time, sender's phone number,
and page number to each page of the faxes that this
product receives.
Sets product to send all received faxes to another fax
machine.
Modifies the blocked fax list. The blocked fax list can
contain up to 30 numbers. When the product receives a
call from one of the blocked fax numbers, it deletes the
incoming fax. It also logs the blocked fax in the activity log
along with job-accounting information.
Sets whether all received faxes stored in available memory
can be reprinted.
ENWW
Table 2-6 Fax setup menu (continued)
Menu Item
Sub-menu item
Sub-menu item
Description
Private receive
On
Off
Setting the Private receive feature to On requires you to
set a password. After the password is set, the following
options are set:
Print faxes
●
The Private receive feature is turned on.
●
All old faxes are deleted from memory.
●
The Forward fax or Receive to PC options are set
to Off and are not allowed to be set.
●
All incoming faxes are stored in memory.
F/T ring time
All faxes
Error correction
This item sets the time, in seconds, for how long the product
generates the audible ring sound for an incoming voice
call.
On
Off
Fax Speed
Fast(V.34)
Medium(V.17)
Sets whether the product sends or receives the error portion
again when a fax transmission error occurs.
Increases or decreases the allowed fax communication
speed.
Slow(V.29)
Table 2-7 System setup menu
Menu Item
Sub-menu item
Language
(List of available
control-panel
display languages.)
Paper setup
Def. paper size
Sub-menu item
Description
Sets the language in which the control panel displays
messages and product reports.
Letter
Sets the size for printing internal reports or any copy job.
A4
Legal
Def. paper type
Print Density
ENWW
(Range of 1-5)
Lists available
paper types.
Sets the type for printing internal reports or any copy job.
Sets how much toner the product should use to darken lines
and edges.
Control-panel menus
19
Table 2-7 System setup menu (continued)
Menu Item
Sub-menu item
Sub-menu item
Description
Volume settings
Alarm volume
Soft
Sets the volume levels for the product.
Ring volume
Medium
Key-press
volume
Loud
Phoneline
volume
Time/Date
Off
(Settings for time
format, current time,
date format, and
current date.)
Sets the time and date setting for the product.
Table 2-8 Service menu
Menu item
Sub-menu item
Description
T.30 trace
Never
Prints or schedules a report that is used to troubleshoot fax
transmission issues.
Now
If error
At end of call
Restore Defaults
Sets all customized settings to the factory default values.
Cleaning Mode
Cleans the product when specks or other marks appear on printed
output. The cleaning process removes dust and excess toner from
the paper path.
When selected, the product prompts you to load plain Letter or A4
paper in the tray. Press the OK button to begin the cleaning
process. Wait until the process completes. Discard the page that
prints.
USB speed
High
Sets the USB speed.
Full
Less paper curl
On
Off
When printed pages are consistently curled, this option sets the
product to a mode that reduces curl.
The default setting is Off.
Archive print
On
Off
When printing pages that will be stored for a long time, this
option sets the product to a mode that reduces toner smearing and
dusting.
The default setting is Off.
20
Chapter 2 Control panel menus (M1210 Series only)
ENWW
Table 2-9 Network config. menu
Menu item
Sub-menu item
Description
TCP/IP Config
Automatic
Select the Automatic option to automatically
configure all the TCP/IP settings.
Manual
Select the Manual option to manually configure the
IP address, subnet mask, and default gateway.
The default setting is Automatic.
Link Speed
Automatic (default)
Sets the link speed manually if needed.
10T Full
After setting the link speed, the product automatically
restarts.
10T Half
100TX Full
100TX Half
Network Services
IPv4
IPv6
This item is used by the network administrator to limit
the network services available on this product.
On
Off
The default setting for all items is On.
Show IP address
No
Yes
No: The product IP address will not appear on the
control-panel display.
Yes: The product IP address will appear on the
control-panel display, alternating between supplies
information and the product IP address. The IP
address will not be displayed if an error condition
exits.
The default setting is No.
Restore Defaults
ENWW
Press the OK button to restore the network
configuration settings to the default values.
Control-panel menus
21
22
Chapter 2 Control panel menus (M1210 Series only)
ENWW
3
ENWW
Software for Windows
●
Supported operating systems for Windows
●
Printer driver
●
Priority for print settings
●
Change printer-driver settings for Windows
●
Remove software for Windows
●
Supported utilities for Windows
23
Supported operating systems for Windows
The product supports the following Windows operating systems:
Full software installation
Print and scan drivers only
●
Windows XP
●
Windows 2003 Server
●
Windows Vista (32-bit and 64-bit)
●
Windows 2008 Server
●
Windows 7 (32-bit and 64-bit)
Printer driver
Printer drivers provide access to product features, such as printing on custom-sized paper, resizing
documents, and inserting watermarks.
NOTE: The most recent drivers are available at www.hp.com/go/ljm1130series_software or
www.hp.com/go/ljm1210series_software. Depending on the configuration of Windows-based
computers, the installation program for the product software automatically checks the computer for
Internet access in order to obtain the latest drivers.
Priority for print settings
Changes to print settings are prioritized depending on where the changes are made:
NOTE: The names of commands and dialog boxes might vary depending on your software program.
24
●
Page Setup dialog box: Click Page Setup or a similar command on the File menu of the
program you are working in to open this dialog box. Settings changed here override settings
changed anywhere else.
●
Print dialog box: Click Print, Print Setup, or a similar command on the File menu of the
program you are working in to open this dialog box. Settings changed in the Print dialog box
have a lower priority and usually do not override changes made in the Page Setup dialog box.
●
Printer Properties dialog box (printer driver): Click Properties in the Print dialog box
to open the printer driver. Settings changed in the Printer Properties dialog box usually do not
override settings anywhere else in the printing software. You can change most of the print settings
here.
●
Default printer driver settings: The default printer driver settings determine the settings used
in all print jobs, unless settings are changed in the Page Setup, Print, or Printer Properties
dialog boxes.
●
Printer control panel settings: Settings changed at the printer control panel have a lower
priority than changes made anywhere else.
Chapter 3 Software for Windows
ENWW
Change printer-driver settings for Windows
Change the settings for all print jobs until the software program is
closed
1.
On the File menu in the software program, click Print.
2.
Select the driver, and then click Properties or Preferences.
The steps can vary; this procedure is most common.
Change the default settings for all print jobs
1.
Windows XP, Windows Server 2003, and Windows Server 2008 (using the
default Start menu view): Click Start, and then click Printers and Faxes.
Windows XP, Windows Server 2003, and Windows Server 2008 (using the
Classic Start menu view): Click Start, click Settings, and then click Printers.
Windows Vista: Click Start, click Control Panel, and then in the category for Hardware
and Sound click Printer.
2.
Right-click the driver icon, and then select Printing Preferences.
Change the product configuration settings
1.
Windows XP, Windows Server 2003, and Windows Server 2008 (using the
default Start menu view): Click Start, and then click Printers and Faxes.
Windows XP, Windows Server 2003, and Windows Server 2008 (using the
Classic Start menu view): Click Start, click Settings, and then click Printers.
Windows Vista: Click Start, click Control Panel, and then in the category for Hardware
and Sound click Printer.
2.
Right-click the driver icon, and then select Properties.
3.
Click the Device Settings tab.
Remove software for Windows
Windows XP
ENWW
1.
Click Start, Control Panel, and then Add or Remove Programs.
2.
Find and select the product from the list.
3.
Click the Change/Remove button to remove the software.
Change printer-driver settings for Windows
25
Windows Vista
26
1.
Click Start, Control Panel, and then Programs and Features.
2.
Find and select the product from the list.
3.
Select the Uninstall/Change option.
Chapter 3 Software for Windows
ENWW
Supported utilities for Windows
HP Toolbox software
HP Toolbox is a software program that you can use for the following tasks:
●
Check the product status.
●
Configure the product settings.
●
Configure pop-up-alert messages.
●
View troubleshooting information.
●
View online documentation.
HP Embedded Web Server (M1210 Series only)
The product is equipped with the HP Embedded Web Server, which provides access to information
about product and network activities. This information appears in a Web browser, such as Microsoft
Internet Explorer, Netscape Navigator, Apple Safari, or Mozilla Firefox.
The HP Embedded Web Server resides on the product. It is not loaded on a network server.
The HP Embedded Web Server provides an interface to the product that anyone who has a networkconnected computer and a standard Web browser can use. No special software is installed or
configured, but you must have a supported Web browser on your computer. To gain access to the
HP Embedded Web Server, type the IP address for the product in the address line of the browser.
Other Windows components and utilities
ENWW
●
Software installer — automates the printing system installation
●
Online Web registration
●
HP LaserJet Scan
●
PC Fax Send
Supported utilities for Windows
27
28
Chapter 3 Software for Windows
ENWW
4
ENWW
Use the product with Mac
●
Software for Mac
●
Print with Mac
●
Fax with Mac (M1210 Series only)
●
Scan with Mac
29
Software for Mac
Supported operating systems for Macintosh
The product supports the following Macintosh operating systems:
●
Mac OS X V10.3.9, V10.4, V10.5, and later
NOTE: For Mac OS X V10.4 and later, PPC and Intel® Core™ Processor Macs are supported.
Supported printer drivers for Macintosh
The HP LaserJet software installer provides PostScript® Printer Description (PPD) files, a CUPS driver,
and the HP Printer Utilities for Mac OS X. The HP printer PPD file, in combination with the CUPS driver,
provides full printing functionality and access to specific HP printer features.
Remove software for Mac
Use the uninstall utility to remove the software.
1.
Browse to the following folder on the hard drive:
Applications/HP LaserJet Professional M1130 MFP Series/ (M1130 Series)
Applications/HP LaserJet Professional M1210 MFP Series/ (M1210 Series)
2.
Double-click the HP Uninstaller.app file.
3.
Click the Continue button, and then follow the onscreen instructions to remove the software.
Priority for print settings for Macintosh
Changes to print settings are prioritized depending on where the changes are made:
NOTE: The names of commands and dialog boxes might vary depending on your software program.
30
●
Page Setup dialog box: Click Page Setup or a similar command on the File menu of the
program you are working in to open this dialog box. Settings changed here might override
settings changed anywhere else.
●
Print dialog box: Click Print, Print Setup, or a similar command on the File menu of the
program you are working in to open this dialog box. Settings changed in the Print dialog box
have a lower priority and do not override changes made in the Page Setup dialog box.
●
Default printer driver settings: The default printer driver settings determine the settings used
in all print jobs, unless settings are changed in the Page Setup, Print, or Printer Properties
dialog boxes.
●
Printer control panel settings: Settings changed at the printer control panel have a lower
priority than changes made anywhere else.
Chapter 4 Use the product with Mac
ENWW
Change printer-driver settings for Mac
Change the settings for all print
jobs until the software program
is closed
Change the default settings for
all print jobs
Change the product configuration
settings
1.
On the File menu, click the Print
button.
1.
On the File menu, click the Print
button.
Mac OS X 10.4
2.
Change the settings that you want
on the various menus.
2.
Change the settings that you want
on the various menus.
3.
On the Presets menu, click the
Save As... option and type a
name for the preset.
These settings are saved in the Presets
menu. To use the new settings, you must
select the saved preset option every time
you open a program and print.
1.
From the Apple menu
, click the
System Preferences menu and
then click the Print & Fax icon.
2.
Click the Printer Setup button.
3.
Click the Installable Options
menu.
Mac OS X 10.5 and 10.6
1.
From the Apple menu
, click the
System Preferences menu and
then click the Print & Fax icon.
ENWW
2.
Select the product in the left side of
the window.
3.
Click the Options & Supplies
button.
4.
Click the Driver tab.
5.
Configure the installed options.
Software for Mac
31
Print with Mac
Create and use printing presets with Mac
Use printing presets to save the current printer driver settings for reuse.
Create a printing preset
1.
On the File menu, click the Print option.
2.
Select the driver.
3.
Select the print settings that you want to save for reuse.
4.
In the Presets menu, click the Save As... option, and type a name for the preset.
5.
Click the OK button.
Use printing presets
1.
On the File menu, click the Print option.
2.
Select the driver.
3.
In the Presets menu, select the printing preset.
NOTE: To use printer-driver default settings, select the standard option.
Resize documents or print on a custom paper size with Mac
Mac OS X 10.4, 10.5, and 10.6
32
1.
On the File menu, click the Page Setup option.
2.
Select the product, and then select the correct settings for the Paper Size and
Orientation options.
Mac OS X 10.5 and 10.6
1.
On the File menu, click the Print option.
Use one of these methods.
2.
Click the Page Setup button.
3.
Select the product, and then select the correct settings for the Paper Size and
Orientation options.
1.
On the File menu, click the Print option.
2.
Open the Paper Handling menu.
3.
In the Destination Paper Size area, click the Scale to fit paper size
box, and then select the size from the drop-down list.
Chapter 4 Use the product with Mac
ENWW
Print a cover page with Mac
1.
On the File menu, click the Print option.
2.
Select the driver.
3.
Open the Cover Page menu, and then select where to print the cover page. Click either the
Before Document button or the After Document button.
4.
In the Cover Page Type menu, select the message that you want to print on the cover page.
NOTE: To print a blank cover page, select the standard option from the Cover Page Type
menu.
Print multiple pages on one sheet of paper with Mac
ENWW
1.
On the File menu, click the Print option.
2.
Select the driver.
3.
Open the Layout menu.
4.
From the Pages per Sheet menu, select the number of pages that you want to print on each
sheet (1, 2, 4, 6, 9, or 16).
5.
In the Layout Direction area, select the order and placement of the pages on the sheet.
6.
From the Borders menu, select the type of border to print around each page on the sheet.
Print with Mac
33
Print on both sides (duplex) with Mac
Print on both sides manually
1.
Load paper face-up in the input tray.
2.
On the File menu, click Print.
3.
Mac OS X v10.4: In the Layout drop-down list, select the Long-edged binding item or the
Short-edged binding item.
-orMac OS X v10.5 and v10.6: Click the Two-sided check box.
4.
34
Click Print. Follow the instructions in the dialog box that opens on the computer screen before
placing the output stack in the tray for printing the second half.
Chapter 4 Use the product with Mac
ENWW
ENWW
5.
Retrieve the printed stack from the output bin, and, maintaining the paper orientation, place it with
the printed-side facing down in the input tray.
6.
At the computer, click the Continue button to print the second side of the job.
Print with Mac
35
Fax with Mac (M1210 Series only)
36
1.
In the software program, on the File menu, select Print.
2.
Click PDF, and then select Fax PDF.
3.
Enter a fax number in the To field.
4.
To include a fax cover page, select Use Cover Page, and then enter the cover page subject and
message (optional).
5.
Click Fax.
Chapter 4 Use the product with Mac
ENWW
Scan with Mac
Use the HP Director software to scan images to a Mac computer.
Use page-by-page scanning
1.
Load the original that is to be scanned face-down in the document feeder.
2.
Click the HP Director icon in the dock.
3.
Click the HP Director, and then click Scan to open the HP dialog box.
4.
Click Scan.
5.
To scan multiple pages, load the next page and click Scan. Repeat until all pages are scanned.
6.
Click Finish, and then click Destinations.
Scan to file
1.
In Destinations, choose Save To File(s).
2.
Name the file and specify the destination location.
3.
Click Save. The original is scanned and saved.
Scan to e-mail
ENWW
1.
In Destinations, choose E-mail.
2.
A blank e-mail opens with the scanned document as an attachment.
3.
Enter an e-mail recipient, add text, or other attachments, then click Send.
Scan with Mac
37
38
Chapter 4 Use the product with Mac
ENWW
5
ENWW
Connect the product
●
Supported network operating systems
●
Connect with USB
●
Connect to a network (M1210 Series only)
39
Supported network operating systems
NOTE: Only the M1210 Series series supports network functions.
The following operating systems support network printing:
●
Windows 7
●
Windows Vista (Starter Edition, 32-bit, and 64-bit)
●
Windows XP (32-bit, Service Pack 2)
●
Windows XP (64-bit, Service Pack 1)
●
Windows Server 2003 (Service Pack 1)
●
Windows Server 2008 (32-bit and 64-bit)
●
Mac OS X v10.4, v10.5, and v10.6
Printer sharing disclaimer
HP does not support peer-to-peer networking, as the feature is a function of Microsoft operating systems
and not of the HP printer drivers. Go to Microsoft at www.microsoft.com.
40
Chapter 5 Connect the product
ENWW
Connect with USB
This product supports a USB 2.0 connection. You must use an A-to-B type USB cable that is no longer
than 2 meters (6.56 feet).
CD installation
1.
Insert the software installation CD into the computer CD drive.
NOTE: Do not connect the USB cable until prompted.
2.
If the installation program does not open automatically, browse the CD contents and run the
SETUP.EXE file.
3.
Follow the onscreen instructions for installing the software.
When you use the CD to install the software, you can select the following types of installations:
●
Easy Install (recommended)
You are not prompted to accept or make changes to defaults.
●
Advanced Install
You are prompted to accept or make changes to defaults.
HP Smart Install
NOTE: This installation type is supported for Windows only.
The HP Smart Install allows you to install the product driver and software by connecting the product to a
computer through a USB cable.
NOTE: The installation CD is not required during an HP Smart Install. Do not insert the software
installation CD into the computer CD drive.
ENWW
1.
Turn the product on.
2.
Connect the USB cable.
3.
The HP Smart Install program should start automatically. Follow the onscreen instructions to install
the software.
●
If the HP Smart Install program does not start automatically, AutoPlay might be disabled on
the computer. Browse the computer and double-click the HP Smart Install drive to run the
program.
●
If the program prompts you to select a connections type, select the Connect via the USB
Port option.
Connect with USB
41
Connect to a network (M1210 Series only)
Supported network protocols
To connect a networking-equipped product to your network, you need a network that uses the following
protocol.
●
Functional wired TCP/IP network
Install the product on a wired network
You can install the product on a network by using the HP Smart Install or from the product CD. Before
you begin the installation process, do the following:
1.
Connect the CAT-5 Ethernet cable to an available port on the Ethernet hub or router. Do not
connect the cable to an uplink port on the hub or router.
2.
Connect the Ethernet cable to the Ethernet port on the back of the product.
3.
Verify that one of the network lights (10 or 100) is illuminated on the network port located on the
back of the product.
HP Smart Install on a wired network
42
1.
Print a configuration page and locate the product IP address.
2.
Open a Web browser using the computer where you want to install the product.
3.
Type the IP address for the product in the address line of the browser.
4.
Click the HP Smart Install tab.
5.
Click the Download button.
6.
Follow the onscreen instructions to complete the product installation.
Chapter 5 Connect the product
ENWW
CD installation on a wired network
NOTE: When you use the CD to install the software, you can select the Easy Install (recommended) or
the Advanced Install (you are prompted to accept or make changes to defaults) installation type.
1.
Insert the software installation CD into the computer CD drive.
2.
If the installation program does not open automatically, browse the CD contents and run the
SETUP.EXE file.
3.
Follow the on-screen instructions for setting up the product and installing the software.
NOTE: Make sure that you select Connect via the Network when prompted.
Configure network settings
View or change network settings
Use the embedded Web server to view or change IP configuration settings.
1.
Print a configuration page, and locate the IP address.
●
If you are using IPv4, the IP address contains only digits. It has this format:
xxx.xxx.xxx.xxx
●
If you are using IPv6, the IP address is a hexadecimal combination of characters and digits. It
has a format similar to this:
xxxx::xxxx:xxxx:xxxx:xxxx
2.
To open the embedded Web server, type the IP address into the address line of a Web browser.
3.
Click the Networking tab to obtain network information. You can change settings as needed.
Set or change the network password
Use the embedded Web server to set a network password or change an existing password.
1.
Open the embedded Web server, click the Networking tab, and click the Password link.
NOTE: If a password has previously been set, you are prompted to type the password. Type the
password, and then click the Apply button.
2.
Type the new password in the Password box and in the Confirm Password box.
3.
At the bottom of the window, click the Apply button to save the password.
IP address
The product IP address can be set manually, or it can be configured automatically using DHCP, BootP,
or AutoIP.
To change the IP address manually, use the Networking tab in the embedded Web server.
ENWW
Connect to a network (M1210 Series only)
43
Link speeds and duplex settings
NOTE: In this section duplex refers to bi-directional communication, not two-sided printing.
Use the Networking tab in the embedded Web server to set the link speed if necessary.
Incorrect changes to the link speed setting might prevent the product from communicating with other
network devices. For most situations, leave the product in automatic mode. Changes can cause the
product to turn off, and then on. Make changes only when the product is idle.
44
Chapter 5 Connect the product
ENWW
6
ENWW
Paper and print media
●
Understand paper use
●
Change the printer driver to match the paper type and size
●
Supported paper sizes
●
Supported paper types
●
Load paper trays
●
Configure trays
45
Understand paper use
This product supports a variety of paper and other print media in accordance with the guidelines in this
user guide. Paper or print media that does not meet these guidelines might cause poor print quality,
increased jams, and premature wear on the product.
For best results, use only HP-brand paper and print media designed for laser printers or multiuse. Do
not use paper or print media made for inkjet printers. Hewlett-Packard Company cannot recommend
the use of other brands of media because HP cannot control their quality.
Store paper in the original package to prevent exposing the paper to moisture and other damage. Do
not open the package until you are ready to use the paper.
It is possible for paper to meet all of the guidelines in this user guide and still not produce satisfactory
results. This might be the result of improper handling, unacceptable temperature and/or humidity levels,
or other variables over which Hewlett-Packard has no control.
CAUTION: Using paper or print media that does not meet Hewlett-Packard's specifications might
cause problems for the product, requiring repair. This repair is not covered by the Hewlett-Packard
warranty or service agreements.
Special paper guidelines
This product supports printing on special media. Use the following guidelines to obtain satisfactory
results. When using special paper or print media, be sure to set the type and size in the printer driver
to obtain the best results.
CAUTION: HP LaserJet products use fusers to bond dry toner particles to the paper in very precise
dots. HP laser paper is designed to withstand this extreme heat. Using inkjet paper could damage the
product.
Media type
Do
Envelopes
●
Store envelopes flat.
●
●
Use envelopes where the seam
extends all the way to the corner of
the envelope.
Do not use envelopes that are
wrinkled, nicked, stuck together, or
otherwise damaged.
●
Do not use envelopes that have
clasps, snaps, windows, or coated
linings.
●
Do not use self-stick adhesives or
other synthetic materials.
●
Do not use labels that have
wrinkles or bubbles, or are
damaged.
●
Do not print partial sheets of labels.
●
Labels
46
Chapter 6 Paper and print media
Do not
Use peel-off adhesive strips that are
approved for use in laser printers.
●
Use only labels that have no
exposed backing between them.
●
Use labels that lie flat.
●
Use only full sheets of labels.
ENWW
Media type
Do
Transparencies
●
Use only transparencies that are
approved for use in laser printers.
●
Place transparencies on a flat
surface after removing them from
the product.
Letterhead or preprinted forms
●
Heavy paper
Glossy or coated paper
All paper types
ENWW
Do not
●
Do not use transparent print media
not approved for laser printers.
Use only letterhead or forms
approved for use in laser printers.
●
Do not use raised or metallic
letterhead.
●
Use only heavy paper that is
approved for use in laser printers
and meets the weight specifications
for this product.
●
Do not use paper that is heavier
than the recommended media
specification for this product unless
it is HP paper that has been
approved for use in this product.
●
Use only glossy or coated paper
that is approved for use in laser
printers.
●
Do not use glossy or coated paper
designed for use in inkjet products.
●
●
Use coated paper in the
temperature and humidity range for
this product.
Do not use coated paper in
extremely high or low humidity
environments.
●
Store paper in the original
packaging.
●
Do not use paper that is curled.
●
●
Store paper in a dust-free area.
Do not use paper that has been
stored in a humid environment.
Understand paper use
47
Change the printer driver to match the paper type
and size
Change the paper size and type (Windows)
1.
On the File menu in the software program, click Print.
2.
Select the product, and then click the Properties or Preferences button.
3.
Click the Paper/Quality tab.
4.
Select a size from the Paper size drop-down list.
5.
Select a paper type from the Paper type drop-down list.
6.
Click the OK button.
Change the paper size and type (Mac)
48
1.
On the File menu in the software program, click the Print option.
2.
In the Copies & Pages menu, click the Paper Handling menu.
3.
Select a size from the Paper Size drop-down list, and then click the OK button.
4.
Open the Paper menu.
5.
Select a type from the Type is drop-down list.
6.
Click the Print button.
Chapter 6 Paper and print media
ENWW
Supported paper sizes
This product supports various paper sizes, and it adapts to various media.
NOTE: To obtain best print results, select the appropriate paper size and type in your print driver
before printing.
Table 6-1 Supported paper and print media sizes
Size
Dimensions
Letter
216 x 279 mm (8.5 x 11 in)
Legal
216 x 356 mm (8.5 x 14 in)
A4
210 x 297 mm (8.27 x 11.69 in)
Executive
184 x 267 mm (7.25 x 10.5 in)
A5
148 x 210 mm (5.83 x 8.27 in)
A6
105 x 148 mm (4.13 x 5.83 in)
B5 (JIS)
182 x 257 mm (7.17 x 10.12 in)
16k
184 x 260 mm (7.24 x 10.23 in)
Input tray
Document feeder
Minimum: 76 x
127 mm (3 x 5 in)
Minimum:
147 x 211 mm
(5.8 x 8.3 in)
195 x 270 mm (7.68 x 10.62 in)
197 x 273 mm (7.75 x 10.75 in)
Custom
Maximum: 216 x
356 mm (8.5 x 14.0 in)
Maximum: 216 x
356 mm (8.5 x 14.0 in)
Table 6-2 Supported envelopes and postcards
ENWW
Size
Dimensions
Envelope #10
105 x 241 mm (4.13 x 9.49 in)
Envelope DL
110 x 220 mm (4.33 x 8.66 in)
Envelope C5
162 x 229 mm (6.93 x 9.84 in)
Envelope B5
176 x 250 mm (6.7 x 9.8 in)
Envelope Monarch
98 x 191 mm (3.9 x 7.5 in)
Postcard (JIS)
100 x 148 mm (3.94 x 5.83 in)
Double postcard (JIS)
148 x 200 mm (5.83 x 7.87 in)
Input tray
Supported paper sizes
49
Supported paper types
For a complete list of specific HP-brand paper that this product supports, go to www.hp.com/support/
ljm1130series or www.hp.com/support/ljm1210series.
Input tray
Document feeder
The input tray supports the following paper types:
●
Plain
●
Light (60-74 g/m2)
●
Mid-Weight (96-110 g/m2)
●
Heavy (111-130 g/m2)
●
Extra Heavy (131-175 g/m2)
●
Transparency
●
Labels
●
Letterhead
●
Envelope
●
Preprinted
●
Prepunched
●
Color
●
Bond
●
Recycled
●
Rough
●
Vellum
The document feeder supports paper types that are within the following weight range:
●
50
Chapter 6 Paper and print media
60-90 g/m2 (16-24 lb bond)
ENWW
Load paper trays
Load the input tray
NOTE: When you add new media, make sure that you remove all of the media from the input tray
and straighten the stack of new media. Do not fan the media. This reduces jams by preventing multiple
sheets of media from feeding through the product at one time.
1.
Load the paper face-up, top forward in the
input tray.
2.
Adjust the guides until they are snug against
the paper.
ENWW
Load paper trays
51
Tray adjustment for short media
To print on media shorter than 185 mm (7.28 in), use the short media extender to adjust your input
tray.
52
1.
Remove the short media extender tool from the
storage slot on the left side of the media input
area.
2.
Attach the tool to the front media guide.
Chapter 6 Paper and print media
ENWW
3.
Insert the paper into the product, and adjust
the side media guides so they are snug against
the paper.
4.
Push the paper into the product until it stops,
and then slide the front media guide so the
tool supports the paper.
5.
When finished printing with short media,
remove the short media extender tool, and
then place it back in the storage slot.
ENWW
Load paper trays
53
Load the document feeder (M1210 Series only)
NOTE: When you add new media, make sure that you remove all of the media from the input tray
and straighten the stack of new media. Do not fan the media. This reduces jams by preventing multiple
sheets of media from feeding through the product at one time.
CAUTION: To prevent damage to the product, do not load an original document that contains
correction tape, correction fluid, paper clips, or staples. Also, do not load photographs, small originals,
or fragile originals into the document feeder.
54
1.
Insert the originals into the document feeder
face-up.
2.
Adjust the guides until they are snug against
the paper.
Chapter 6 Paper and print media
ENWW
Tray and bin capacity
Tray or bin
Paper type
Specifications
Quantity
Input tray
Paper
Range:
150 sheets of 60 g/m2 (16 lb)
bond
60 g/m2 (16 lb) bond to 163 g/
m2 (43 lb) bond
Output bin
Envelopes
60 g/m2 (16 lb) bond to 90 g/
m2 (24 lb) bond
Up to 10 envelopes
Transparencies
Minimum 0.13 mm (0.005 in)
thick
Up to 75 transparencies
Paper
Range:
Up to 100 sheets of 75 g/m2
(20 lb) bond
60 g/m2 (16 lb) bond to 163 g/
m2 (43 lb) bond
Document feeder (M1210 Series
only)
Envelopes
Less than 60 g/m2 (16 lb) bond
to 90 g/m2 (24 lb) bond
Up to 10 envelopes
Transparencies
Minimum 0.13 mm (0.005 in)
thick
Up to 75 transparencies
Paper
Range:
Up to 35 sheets
60 g/m2 (16 lb) bond to 90 g/
m2 (24 lb) bond
Paper orientation for loading trays
If you are using paper that requires a specific orientation, load it according to the information in the
following table.
Paper type
How to load paper
Preprinted or letterhead
●
Face up
●
Top edge leading into the product
●
Face up
●
Holes toward the left side of the product
●
Face up
●
Left short edge leading into the product
Prepunched
Envelope
ENWW
Load paper trays
55
Configure trays
Change the default paper-size setting (M1130 Series)
1.
Use the printer driver to change the default settings. Follow the appropriate procedure, depending
on the operating system you are using.
Windows XP, Windows Server 2003, and Windows Server 2008 (using the
default Start menu view)
a.
Click Start, and then click Printers and Faxes.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Windows XP, Windows Server 2003, and Windows Server 2008 (using the
Classic Start menu view)
a.
Click Start, click Settings, and then click Printers.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Windows Vista
a.
Click Start, click Control Panel, and then in the category for Hardware and Sound
click Printer.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Mac OS X 10.4
a.
From the Apple menu
Fax icon.
b.
Click the Printer Setup button.
, click the System Preferences menu and then click the Print &
Mac OS X 10.5 and 10.6
2.
56
a.
From the Apple menu
Fax icon.
b.
Select the product in the left side of the window.
c.
Click the Options & Supplies button.
d.
Click the Driver tab.
, click the System Preferences menu and then click the Print &
Select the appropriate paper size.
Chapter 6 Paper and print media
ENWW
Change the default paper-size setting (M1210 Series)
1.
Press the Setup button.
2.
Use the arrow buttons to select the System setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Paper setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Def. paper size menu, and then press the OK button.
5.
Use the arrow buttons to select a size, and then press the OK button.
Change the default paper-type setting (M1130 Series)
You cannot set a default paper type for this model.
Change the default paper-type setting (M1210 Series)
ENWW
1.
Press the Setup button.
2.
Use the arrow buttons to select the System setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Paper setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Def. paper type menu, and then press the OK button.
5.
Use the arrow buttons to select a type, and then press the OK button.
Configure trays
57
58
Chapter 6 Paper and print media
ENWW
7
ENWW
Print tasks
●
Cancel a print job
●
Print with Windows
59
Cancel a print job
1.
If the print job is currently printing, cancel it by pressing the Cancel
control panel.
button on the product
NOTE: Pressing the Cancel
button clears the job that the product is currently processing. If
more than one process is running, pressing the Cancel
button clears the process that currently
appears on the product control panel.
2.
You can also cancel a print job from a software program or a print queue.
●
Software program: Typically, a dialog box appears briefly on the computer screen,
allowing you to cancel the print job.
●
Windows print queue: If a print job is waiting in a print queue (computer memory) or
print spooler, delete the job there.
●
60
◦
Windows XP, Server 2003, or Server 2008: Click Start, click Settings, and
then click Printers and Faxes. Double-click the product icon to open the window,
right-click the print job that you want to cancel, and then click Cancel.
◦
Windows Vista: Click Start, click Control Panel, and then, under Hardware
and Sound, click Printer. Double-click the product icon to open the window, rightclick the print job that you want to cancel, and then click Cancel.
Macintosh print queue: Open the print queue by double-clicking the product icon in the
dock. Highlight the print job, and then click Delete.
Chapter 7 Print tasks
ENWW
Print with Windows
Open the printer driver with Windows
1.
On the File menu in the software program,
click Print.
2.
Select the product, and then click the
Properties or Preferences button.
Get help for any printing option with Windows
1.
Click the Help button to open the online Help.
ENWW
Print with Windows
61
Change the number of print copies with Windows
1.
On the File menu in the software program, click Print.
2.
Select the product, and then click the Properties or Preferences button.
3.
Click the Advanced tab.
4.
In the Copies area, use the arrow buttons to adjust the number of copies.
If you are printing multiple copies, click the Collate check box to collate the copies.
Print colored text as black with Windows
62
1.
On the File menu in the software program, click Print.
2.
Select the product, and then click the Properties or Preferences button.
3.
Click the Advanced tab.
4.
Click the Print All Text as Black check box. Click the OK button.
Chapter 7 Print tasks
ENWW
Save custom print settings for reuse with Windows
Use a printing quick set
1.
On the File menu in the software program,
click Print.
2.
Select the product, and then click the
Properties or Preferences button.
3.
In the Print Task Quick Sets drop-down
list , select one of the quick sets, and then click
the OK button to print the job with the
predefined settings.
NOTE: The Print Task Quick Sets dropdown list appears on all tabs except the
Services tab.
ENWW
Print with Windows
63
Create a custom printing quick set
64
1.
On the File menu in the software program,
click Print.
2.
Select the product, and then click the
Properties or Preferences button.
Chapter 7 Print tasks
ENWW
3.
Select the print options for the new quick set.
4.
Type a name for the new quick set, and click
the Save button.
Improve print quality with Windows
Select a page size
1.
On the File menu in the software program, click Print.
2.
Select the product, and then click the Properties or Preferences button.
3.
Click the Paper/Quality tab.
4.
Select a size from the Size is drop-down list.
Select a custom page size
ENWW
1.
On the File menu in the software program, click Print.
2.
Select the product, and then click the Properties or Preferences button.
3.
Click the Paper/Quality tab.
Print with Windows
65
4.
Click the Custom button. The Custom Paper Size dialog box opens.
5.
Type a name for the custom size, specify the dimensions, and then click the Save button.
6.
Click the Close button, and then click the OK button.
Select a paper type
1.
On the File menu in the software program, click Print.
2.
Select the product, and then click the Properties or Preferences button.
3.
Click the Paper/Quality tab.
4.
Select a type from the Type is drop-down list.
Select the print resolution
1.
On the File menu in the software program, click Print.
2.
Select the product, and then click the Properties or Preferences button.
3.
Click the Paper/Quality tab.
4.
In the Print Quality area, select an option from the drop-down list. See the printer-driver online
Help for information about each of the available options.
NOTE: To use a draft-quality resolution, in the Print Quality area, click the EconoMode
check box.
Print on preprinted letterhead or forms with Windows
1.
66
On the File menu in the software program,
click Print.
Chapter 7 Print tasks
ENWW
2.
Select the product, and then click the
Properties or Preferences button.
3.
Click the Paper/Quality tab.
4.
From the Type is drop-down list, select the
type of paper you are using, and click the OK
button.
ENWW
Print with Windows
67
Print on special paper, labels, or transparencies with Windows
68
1.
On the File menu in the software program,
click Print.
2.
Select the product, and then click the
Properties or Preferences button.
Chapter 7 Print tasks
ENWW
3.
Click the Paper/Quality tab.
4.
From the Type is drop-down list, select the
type of paper you are using, and click the OK
button.
Print the first or last page on different paper with Windows
1.
On the File menu in the software program,
click Print.
ENWW
Print with Windows
69
70
2.
Select the product, and then click the
Properties or Preferences button.
3.
Click the Paper/Quality tab.
4.
Click the Use Different Paper/Covers
check box, and then select the necessary
settings for the front cover, other pages, and
back cover.
Chapter 7 Print tasks
ENWW
Scale a document to fit page size
1.
On the File menu in the software program,
click Print.
2.
Select the product, and then click the
Properties or Preferences button.
ENWW
Print with Windows
71
3.
Click the Effects tab.
4.
Select the Print Document On option, and
then select a size from the drop-down list.
Add a watermark to a document with Windows
1.
On the File menu in the software program, click Print.
2.
Select the product, and then click the Properties or Preferences button.
3.
Click the Effects tab.
4.
Select a watermark from the Watermarks drop-down list.
To print the watermark on the first page only, click the First Page Only check box. Otherwise,
the watermark is printed on each page.
72
Chapter 7 Print tasks
ENWW
Print on both sides (duplex) with Windows
Manually print on both sides (duplex) with Windows
1.
Load paper face-up in the input tray.
2.
On the File menu in the software program,
click Print.
3.
Select the product, and then click the
Properties or Preferences button.
ENWW
Print with Windows
73
74
4.
Click the Finishing tab.
5.
Select the Print on both sides (manually)
check box. Click the OK button to print the
first side of the job.
6.
Retrieve the printed stack from the output bin,
and, maintaining the paper orientation, place
it with the printed-side facing down in the input
tray.
7.
At the computer, click the Continue button to
print the second side of the job.
Chapter 7 Print tasks
ENWW
Create a booklet with Windows
1.
On the File menu in the software program,
click Print.
2.
Select the product, and then click the
Properties or Preferences button.
3.
Click the Finishing tab.
ENWW
Print with Windows
75
4.
Click the Print on both sides (manually)
check box.
5.
In the Booklet Printing drop-down list,
select a binding option. The Pages per
sheet option automatically changes to 2
pages per sheet.
Use HP ePrint
HP ePrint is a suite of Web-based printing services that enable a supported HP product to print
documents of the following types:
●
E-mail messages and attachments sent directly to the HP product’s e-mail address
●
Documents from select mobile device print applications
Use HP Cloud Print
Use HP Cloud Print to print e-mail messages and attachments by sending them to the product's e-mail
address from any e-mail enabled device.
76
Chapter 7 Print tasks
ENWW
NOTE: The product must be connected to a wired or wireless network. To use HP Cloud Print, you
must first have access to the Internet and enable HP Web Services.
1.
2.
Enable HP Web Services from the product control panel by following these steps:
a.
At the Home screen on the product control panel, press the
b.
Use the arrow buttons to scroll to the HP Web Services menu, and then press the OK
button.
c.
Use the arrow buttons to scroll to the Enable Web Services option, and then press the OK
button. An information page prints.
button.
For advanced configuration options, enable HP Web Services in the HP Embedded Web Server
(EWS) by following these steps:
a.
After the product is connected to the network, print a configuration page and identify the
product IP address.
b.
At your computer, open a Web browser and enter the product IP address into the address
line. The HP EWS appears.
c.
Click the HP Web Services tab. If your network does not use a proxy server to access the
Internet, proceed to the next step. If your network uses a proxy server to access the Internet,
follow these instructions before proceeding to the next step:
i.
Select the Proxy Settings tab.
ii.
Select the Check this box if your network uses a proxy server to access
the Internet check box.
iii. In the Proxy Server field, enter the proxy server address and port number, and then
click the Apply button.
ENWW
d.
Select the HP Web Services tab and click the Enable button. The product configures the
connection to the Internet, and then a message appears informing you that an information
sheet will be printed.
e.
Click the OK button. An information page prints out. On the information page, look for the email address that is automatically assigned to the product.
3.
To print a document, attach it to an e-mail message, and then send the message to the product's email address. Go to www.hpeprintcenter.com for a list of supported document types
4.
Optionally, use the HP ePrintCenter Web site to define security settings and to configure default
print settings for all HP ePrint jobs sent to this product:
a.
Open a Web browser and go to www.hpeprintcenter.com.
b.
Click Sign In, and enter your HP ePrintCenter credentials or sign up for a new account.
Print with Windows
77
c.
Select your product from the list, or click the + Add printer button to add it. To add the
product, you need the product code, which is the segment of the product e-mail address that
is before the @ symbol.
NOTE: This code is valid for only 24 hours from the time you enable HP Web Services. If it
expires, follow the instructions to enable HP Web Services again, and obtain a new code.
d.
Click the Setup button. The HP ePrint Settings dialog box appears. Three tabs are
available:
●
Allowed Senders. To prevent your product from printing unexpected documents, click
the Allowed Senders tab. Click Allowed Senders Only, and then add the e-mail
addresses from which you want to allow ePrint jobs.
●
Print Options. To set up default settings for all ePrint jobs sent to this product, click the
Print Options tab, and then select the settings that you want to use.
●
Advanced. To change the product’s e-mail address, click the Advanced tab.
Use HP Direct Print (wireless models only)
Use HP Direct Print to print directly to the product from any mobile device (such as a smart phone, net
book, or laptop computer).
NOTE: No setup is necessary, but HP Direct Print must be enabled. Your mobile device must have an
HP print application installed.
1.
2.
78
To enable HP Direct Print from the product control panel, follow these steps:
a.
Use the arrow buttons to select the Network config. menu, and then press the OK button.
b.
Use the arrow buttons to select the Wireless Menu, and then press the OK button.
c.
Use the arrow buttons to select the Wireless Direct, and then press the OK button.
For advanced configuration options, enable HP Web Services in the HP Embedded Web Server
(EWS) by following these steps:
a.
After the product is connected to the network, print a configuration page and identify the
product IP address.
b.
At your computer, open a Web browser and enter the product IP address into the address
line. The HP EWS screen appears.
Chapter 7 Print tasks
ENWW
c.
Click the Networking tab.
d.
On the Networking page, click the check box, enter the network name (SSID), and then
click the Apply button. The IP address of the mobile device appears in the Networking
page.
NOTE: To find the network name (SSID), click the Wireless Configuration menu in the
Networking page.
3.
To print a document from an application, select File, and then select Print.
NOTE: If only one product that supports HP Direct Print is connected to the wireless network, the
document prints. If more than one product that supports HP Direct Print is connected, a list of
products appears; you must select your product before proceeding to the next step. If no product is
discovered, you are prompted to search for ePrint or local products.
Use AirPrint
Direct printing using Apple’s AirPrint is supported for iOS 4.2 or later. Use AirPrint to print directly to
the product from an iPad (iOS 4.2), iPhone (3GS or later), or iPod touch (third generation or later) in
the following applications:
●
Mail
●
Photos
●
Safari
●
Select third-party applications
NOTE: The product must be connected to a wired or wireless network.
To print, follow these steps:
1.
2.
Tap the action
item.
Tap Print.
NOTE: If you are printing for the first time, or if your previously selected product is not
available, you must select a product before proceeding to the next step.
3.
Configure the print options and then tap Print.
Print multiple pages per sheet with Windows
1.
On the File menu in the software program,
click Print.
ENWW
Print with Windows
79
80
2.
Select the product, and then click the
Properties or Preferences button.
3.
Click the Finishing tab.
Chapter 7 Print tasks
ENWW
4.
Select the number of pages per sheet from the
Pages per sheet drop-down list.
5.
Select the correct Print page borders,
Page order, and Orientation options.
Select page orientation with Windows
1.
On the File menu in the software program,
click Print.
ENWW
Print with Windows
81
2.
Select the product, and then click the
Properties or Preferences button.
3.
Click the Finishing tab.
4.
In the Orientation area, select the Portrait
or Landscape option.
To print the page image upside down, select
the Rotate by 180 degrees option.
82
Chapter 7 Print tasks
ENWW
8
ENWW
Copy
●
Use copy functions
●
Copy settings
●
Copy on both sides (duplex)
83
Use copy functions
One-touch copy
1.
Load the document onto the scanner glass or into the document feeder (M1210 Series).
2.
Press the Start Copy
3.
Repeat the process for each copy.
button to start copying.
Multiple copies
Create multiple copies (M1130 Series)
84
1.
Load the document onto the scanner glass.
2.
Press the Setup
Chapter 8 Copy
button, and make sure that the Number of Copies
light is on.
ENWW
3.
Press the arrow buttons to adjust the number of copies.
4.
Press the Start Copy
button to start copying.
Create multiple copies (M1210 Series)
1.
Load the document onto the scanner glass or into the document feeder.
2.
Use the keypad to enter the number of copies.
3.
Press the Start Copy
button to start copying.
Copy a multiple-page original
M1130 Series: Load the first page onto the scanner glass, and press the Start Copy
Repeat this process for each page.
button.
M1210 Series: Load a stack of original documents into the document feeder, and press the Start
Copy
button.
Copy identification cards (M1210 Series only)
Use the ID copy feature to copy both sides of identification cards, or other small-size documents, onto
the same side of one sheet of paper. The product scans half of the image area, prompts you to turn the
document over, and then scans again. The product prints both images at the same time.
ENWW
1.
Place the first side of the document face-down on the scanner glass.
2.
Press the Copy Settings
3.
The product scans the first page of the document and then prompts you to load the next page.
Open the scanner lid and turn the document over, place it on a different portion of the scanner
glass, and then press the OK button.
button three times to open the ID Copy menu. Press the OK button.
Use copy functions
85
4.
For multiple-page documents, repeat these steps until you have scanned all the pages.
5.
Press the Start Copy
button to print the pages.
Cancel a copy job
Cancel a copy job (M1130 Series)
▲
Press the Cancel
button on the product control panel.
NOTE: If more than one process is running, pressing the Cancel
process and all pending processes.
button clears the current
Cancel a copy job (M1210 Series)
1.
Press the Cancel
button on the product control panel.
NOTE: If more than one process is running, pressing the Cancel
process and all pending processes.
button clears the current
2.
Remove the remaining pages from the document feeder.
3.
Press the OK button to eject the remaining pages from the document-feeder paper path.
Reduce or enlarge a copy image
Reduce or enlarge copies (M1130 Series)
1.
86
Load the document onto the scanner glass.
Chapter 8 Copy
ENWW
2.
Press the Setup
Reduce/Enlarge
3.
Press the up arrow
to increase the copy
size, or press the down arrow
to decrease
the copy size.
4.
Press the Start Copy
copying.
button repeatedly until the
light is on.
button to start
Reduce or enlarge copies (M1210 Series)
1.
Load the document onto the scanner glass or
into the document feeder.
ENWW
Use copy functions
87
88
2.
Press the Copy Settings
button one time to
open the Reduce/Enlarge menu.
3.
Use the arrow buttons to select the correct
reduction or enlargement option, and then
press the OK button.
4.
Press the Start Copy
copying.
Chapter 8 Copy
button to start
ENWW
Collate a copy job
M1130 Series: The product cannot automatically collate copies.
Collate copies (M1210 Series)
1.
Press the Setup
2.
Use the arrow buttons to select the Copy
setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Def.
Collation option, and then press the OK
button.
4.
Use the arrow buttons to select the On option,
and then press the OK button.
button.
Copy settings
Change copy quality
The following copy-quality settings are available:
ENWW
●
Text: Use this setting for documents that contain mostly text. This is the default setting for the
M1210 Series models.
●
Draft: Use this setting when you are not concerned about the quality of the copy. This setting uses
less toner.
●
Mixed: Use this setting for documents that contain a mixture of text and graphics. This is the
default setting for the M1130 Series models.
●
Film photo: Use this setting to copy photographs.
●
Picture: Use this setting to copy non-photographic graphics.
Copy settings
89
Change the copy quality setting (M1130 Series)
NOTE: For this model, you cannot change the copy-quality setting for individual copy jobs. Use this
procedure to change the default copy-quality setting for all copy jobs.
1.
Use the printer driver to change the default settings. Follow the appropriate procedure, depending
on the operating system you are using.
Windows XP, Windows Server 2003, and Windows Server 2008 (using the
default Start menu view)
a.
Click Start, and then click Printers and Faxes.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Windows XP, Windows Server 2003, and Windows Server 2008 (using the
Classic Start menu view)
a.
Click Start, click Settings, and then click Printers.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Windows Vista
a.
Click Start, click Control Panel, and then in the category for Hardware and Sound
click Printer.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Mac OS X 10.4
a.
From the Apple menu
Fax icon.
b.
Click the Printer Setup button.
, click the System Preferences menu and then click the Print &
Mac OS X 10.5 and 10.6
2.
90
a.
From the Apple menu
Fax icon.
b.
Select the product in the left side of the window.
c.
Click the Options & Supplies button.
d.
Click the Driver tab.
, click the System Preferences menu and then click the Print &
Select the appropriate Copy Quality setting.
Chapter 8 Copy
ENWW
Change the copy quality setting (M1210 Series)
1.
Press the Copy Settings
button two times to
open the Copy Quality menu.
2.
Use the arrow buttons to select a copy-quality
option, and press the OK button.
NOTE: The setting returns to the default
value after two minutes.
Check the scanner glass for dirt and smudges
Over time, specks of debris might collect on the scanner glass and white plastic backing, which can
affect performance. Use the following procedure to clean the scanner glass and white plastic backing.
1.
Use the power switch to turn off the product,
and then unplug the power cord from the
electrical socket.
2.
Open the scanner lid.
ENWW
Copy settings
91
3.
Clean the scanner glass and the white plastic
backing with a soft cloth or sponge that has
been moistened with nonabrasive glass
cleaner.
CAUTION: Do not use abrasives, acetone,
benzene, ammonia, ethyl alcohol, or carbon
tetrachloride on any part of the product; these
can damage the product. Do not place liquids
directly on the glass or platen. They might seep
and damage the product.
4.
Dry the glass and white plastic with a chamois
or a cellulose sponge to prevent spotting.
5.
Plug in the product, and then use the power
switch to turn on the product.
Adjust the lightness or darkness for copies
Adjust the lightness or darkness for copies (M1130 Series)
1.
Press the Setup button repeatedly until the
Lighter/Darker
light is on.
2.
Use the arrow buttons to increase or decrease
the Lighter/Darker setting.
NOTE: The setting returns to the default
value after two minutes.
92
Chapter 8 Copy
ENWW
Adjust the lightness or darkness for copies (M1210 Series)
1.
Press the Lighter/Darker
2.
Use the arrow buttons to increase or decrease
the Lighter/Darker setting.
button.
NOTE: The setting returns to the default
value after two minutes.
ENWW
Copy settings
93
Copy on both sides (duplex)
Copy a two-sided original to a one-sided document
1.
Load the first page of the document onto the
scanner glass or into the document feeder
(M1210 Series).
2.
Press the Start Copy
3.
Flip the original, and then reload it onto the
scanner glass or into the document feeder.
4.
Press the Start Copy
5.
Repeat steps 1 through 4 for each page until
all of the original document pages have been
copied.
button.
button.
Copy a two-sided original to a two-sided document
94
1.
Load the first page of the document onto the
scanner glass or into the document feeder
(M1210 Series).
2.
Press the Start Copy
Chapter 8 Copy
button.
ENWW
3.
Flip the original, and then reload it onto the
scanner glass or into the document feeder.
4.
Remove the copied page from the output bin
and place it face down into the input tray.
5.
Press the Start Copy
6.
Remove the copied page from the output bin,
and then set it aside for manual collating.
7.
Repeat steps 1 through 6, following the
original document page order, until all pages
of the original are copied.
ENWW
button.
Copy on both sides (duplex)
95
96
Chapter 8 Copy
ENWW
9
ENWW
Scan
●
Use scan functions
●
Scan settings
97
Use scan functions
Scan methods
Scan jobs can be performed in the following ways.
●
Scan from the computer by using HP LaserJet Scan (Windows)
●
Scan by using HP Director (Mac)
●
Scan from TWAIN-compliant or Windows Imaging Application (WIA)-compliant software
NOTE: To learn about and use text-recognition software, install the Readiris program from the
software CD-ROM. Text-recognition software is also known as optical character recognition (OCR)
software.
Scan by using HP LaserJet Scan (Windows)
1.
In the HP program group, select Scan to to start HP LaserJet Scan.
2.
Select a scanning destination.
3.
Click Scan.
NOTE: OK should indicate the action that you want to accomplish.
Scan by using HP Director (Mac)
Use page-by-page scanning
1.
Load the original that is to be scanned face-down in the document feeder.
2.
Click the HP Director icon in the dock.
3.
Click the HP Director, and then click Scan to open the HP dialog box.
4.
Click Scan.
5.
To scan multiple pages, load the next page and click Scan. Repeat until all pages are scanned.
6.
Click Finish, and then click Destinations.
Scan to file
98
1.
In Destinations, choose Save To File(s).
2.
Name the file and specify the destination location.
3.
Click Save. The original is scanned and saved.
Chapter 9 Scan
ENWW
Scan to e-mail
1.
In Destinations, choose E-mail.
2.
A blank e-mail opens with the scanned document as an attachment.
3.
Enter an e-mail recipient, add text, or other attachments, then click Send.
Scan by using other software
The product is TWAIN-compliant and Windows Imaging Application (WIA)-compliant. The product
works with Windows-based programs that support TWAIN-compliant or WIA-compliant scanning
devices and with Macintosh-based programs that support TWAIN-compliant scanning devices.
While you are in a TWAIN-compliant or WIA-compliant program, you can gain access to the scanning
feature and scan an image directly into the open program. For more information, see the Help file or
the documentation that came with your TWAIN-compliant or WIA-compliant software program.
Scan from a TWAIN-compliant program
Generally, a software program is TWAIN-compliant if it has a command such as Acquire, File
Acquire, Scan, Import New Object, Insert from, or Scanner. If you are unsure whether the
program is compliant or you do not know what the command is called, see the software program Help
or documentation.
When scanning from a TWAIN-compliant program, the HP LaserJet Scan software program might start
automatically. If the HP LaserJet Scan program starts, you can make changes while previewing the
image. If the program does not start automatically, the image goes to the TWAIN-compliant program
immediately.
Start the scan from within the TWAIN-compliant program. See the software program Help or
documentation for information about the commands and steps to use.
Scan from a WIA-compliant program
WIA is another way to scan an image directly into a software program, such as Microsoft Word. WIA
uses Microsoft software to scan, instead of HP LaserJet Scan software.
Generally, a software program is WIA-compliant if it has a command such as Picture/From
Scanner or Camera in the Insert or File menu. If you are unsure whether the program is WIAcompliant, see the software program Help or documentation.
Start the scan from within the WIA-compliant program. See the software program Help or
documentation for information about the commands and steps to use.
-OrIn the Cameras and Scanner folder, double-click the product icon. This opens the standard Microsoft
WIA Wizard, which enables you to scan to a file.
ENWW
Use scan functions
99
Scanning by using optical character recognition (OCR) software
You can use third-party OCR software to import scanned text into your preferred word-processing
program for editing.
Readiris
The Readiris OCR program is included on a separate CD-ROM that shipped with the product. To use
the Readiris program, install it from the appropriate software CD-ROM, and then follow the instructions
in the online Help.
Cancel a scan
To cancel a scan job, use one of the following procedures.
100
button.
●
On the product control panel, press the Cancel
●
Click the Cancel button in the onscreen dialog box.
Chapter 9 Scan
ENWW
Scan settings
Scan file format
The default file format of a scanned document or photo depends on the scan type as well as the object
being scanned.
●
Scanning a document or a photo to a computer results in the file being saved as a .TIF file.
●
Scanning a document to e-mail results in the file being saved as a .PDF file.
●
Scanning a photo to e-mail results in the file being saved as a .JPEG file.
NOTE: Different file types can be selected when using the scan software program.
Scanner resolution and color
If you are printing a scanned image, and the quality is not what you expected, you might have selected
a resolution or color setting in the scanner software that does not match your needs. Resolution and
color affect the following features of scanned images:
●
Image clarity
●
Texture of gradations (smooth or rough)
●
Scan time
●
File size
Scanning resolution is measured in pixels per inch (ppi).
NOTE: Scanning ppi levels are not interchangeable with printing dpi (dots per inch) levels.
Color, grayscale, and black and white define the number of colors possible. You can adjust the
scanner hardware resolution to up to 1200 ppi. The software can perform an enhanced resolution up
to 19,200 ppi. You can set color and grayscale at 1 bit (black and white), or at 8 bit (256 levels of
gray or color) to 24 bit (true color).
The resolution and color guidelines table lists simple tips that you can follow to meet your scanning
needs.
NOTE: Setting the resolution and color to a high value can create large files that take up disk space
and slow the scanning process. Before setting the resolution and color, determine how you are going to
use the scanned image.
ENWW
Scan settings
101
Resolution and color guidelines
The following table describes the recommended resolution and color settings for different types of scan
jobs.
Intended use
Recommended resolution
Recommended color settings
Fax
150 ppi
●
Black and White
E-mail
150 ppi
●
Black and White, if the image does not require
smooth gradation
●
Grayscale, if the image requires smooth gradation
●
Color, if the image is in color
Edit text
300 ppi
●
Black and White
Print (graphics or text)
600 ppi for complex graphics, or if
you want to significantly enlarge the
document
●
Black and White for text and line art
●
Grayscale for shaded or colored graphics and
photos
●
Color, if the image is in color
●
Black and White for text
●
Grayscale for graphics and photos
●
Color, if the image is in color
300 ppi for normal graphics and text
150 ppi for photos
Display on screen
75 ppi
Color
You can set the color values to the following settings when scanning.
102
Setting
Recommended use
Color
Use this setting for high-quality color photos or documents in which the color is important.
Black and White
Use this setting for text documents.
Grayscale
Use this setting when file size is an issue or when you want a document or photograph to
be scanned quickly.
Chapter 9 Scan
ENWW
Scan quality
Over time, specks of debris might collect on the scanner glass and white plastic backing, which can
affect performance. Use the following procedure to clean the scanner glass and white plastic backing.
1.
Use the power switch to turn off the product,
and then unplug the power cord from the
electrical socket.
2.
Open the scanner lid.
3.
Clean the scanner glass and the white plastic
backing with a soft cloth or sponge that has
been moistened with nonabrasive glass
cleaner.
CAUTION: Do not use abrasives, acetone,
benzene, ammonia, ethyl alcohol, or carbon
tetrachloride on any part of the product; these
can damage the product. Do not place liquids
directly on the glass or platen. They might seep
and damage the product.
4.
Dry the glass and white plastic with a chamois
or a cellulose sponge to prevent spotting.
5.
Plug in the product, and then use the power
switch to turn on the product.
ENWW
Scan settings
103
104
Chapter 9 Scan
ENWW
10 Fax (M1210 Series only)
ENWW
●
Fax features
●
Set up fax
●
Use the phone book
●
Set fax settings
●
Use fax
●
Solve fax problems
●
Regulatory information and warranties
105
Fax features
The product has the following fax features, which are available from the control panel or from the
product software.
●
Fax Setup Wizard for easy fax configuration
●
Plain-paper analog fax with 35-page document feeder and output tray of up to 100-page paper
capacity
●
100-entry phone book
●
Automatic redial
●
Digital storage of up to 500 fax pages
●
Fax forwarding
●
Delayed sending of faxes
●
Ring features: Configure rings to answer and distinctive ring compatibility (service required
through local telecommunications company)
●
Fax confirmation report
●
Junk fax blocking
●
Eight cover page templates available
NOTE: Not all features are listed. The product software might need to be installed for some features
to be available.
106
Chapter 10 Fax (M1210 Series only)
ENWW
Set up fax
Install and connect the hardware
Connect fax to a telephone line
The product is an analog device. HP recommends using the product on a dedicated analog telephone
line.
Connect additional devices
The product includes two fax ports:
●
The “line” port
●
The “telephone” port
, which connects the product to the wall telephone jack.
, which connects additional devices to the product.
Telephones used in conjunction with the product can be employed in two ways:
●
An extension phone is a phone plugged into the same phone line at another location.
●
A downstream phone is one that is plugged into the product or a device that is plugged into the
product.
Connect additional devices in the order that is described in the following steps. The output port for each
device is connected to the input port of the next, forming a "chain". If you do not want to connect a
specific device, skip the step that explains it and continue to the next device.
NOTE: Do not connect more than three devices to the telephone line.
NOTE: Voicemail is not supported with this product.
ENWW
1.
Unplug the power cords for all of the devices that you want to connect.
2.
If the product is not yet connected to a telephone line, see the product installation guide before
proceeding. The product should already be connected to a telephone jack.
Set up fax
107
3.
108
Remove the plastic insert from the "telephone" port (the port that is marked with the telephone
icon).
Chapter 10 Fax (M1210 Series only)
ENWW
4.
To connect an internal or external modem on a computer, plug one end of a telephone cord into
the product “telephone” port
. Plug the other end of the telephone cord into the modem “line”
port.
NOTE: Some modems have a second “line” port to connect to a dedicated voice line. If you
have two “line” ports, see your modem documentation to make sure that you connect to the correct
“line” port.
5.
ENWW
To connect a caller-ID box, plug a telephone cord into the previous device’s “telephone” port. Plug
the other end of the telephone cord into the caller-ID box “line” port.
Set up fax
109
6.
To connect an answering machine, plug a telephone cord into the previous device’s “telephone”
port. Plug the other end of the telephone cord into the answering machine “line” port.
7.
To connect a telephone, plug a telephone cord into the previous device’s “telephone” port. Plug
the other end of the telephone cord into the telephone “line” port.
8.
After you have finished connecting additional devices, plug all of the devices into their power
sources.
Set up fax with a telephone answering machine
●
Set the product rings-to-answer setting for at least one ring more than the number of rings for
which the answering machine is set.
●
If an answering machine is connected to the same telephone line but on a different jack (in
another room, for example), it might interfere with the product's ability to receive faxes.
Set up fax with an extension phone
With this setting turned on, you can alert the product to pick up the incoming fax call by pressing 1-2-3
sequentially on the telephone keypad. The default setting is On. Turn this setting off only if you use
pulse dialing or if you have a service from your telephone company that also uses the 1-2-3 sequence.
The telephone company service does not work if it conflicts with the product.
110
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Recv. setup menu, and then press the OK button.
Chapter 10 Fax (M1210 Series only)
button.
ENWW
4.
Use the arrow buttons to select the Extension Phone menu, and then press the OK button.
5.
Use the arrow buttons to select the On or Off option, and then press the OK button to save the
selection.
Setup for stand-alone fax
1.
Unpack and set up the product.
2.
At the control panel, press the Setup
3.
Use the arrow buttons to select the System setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Time/Date menu, and then press the OK button.
5.
Use the arrow buttons to select the 12-hour clock or 24-hour clock, and then press the OK button.
6.
Use the keypad to enter the current time.
7.
Complete one of the following:
button.
●
For the 12-hour clock, use the arrow buttons to move past the fourth character. Select 1 for
a.m. or 2 for p.m. Press the OK button.
●
For the 24-hour clock, press the OK button.
8.
Use the keypad to enter the current date. Use two digits to specify the month, day, and year. Press
the OK button.
9.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
10. Use the arrow buttons to select the Fax header menu, and then press the OK button.
11. Use the keypad to enter your fax number and your company name or header, and then press the
OK button.
NOTE: The maximum number of characters for the fax number is 20; use up to 25 characters for
the company name.
12. Set other settings as necessary to configure for the product environment.
Configure fax settings
The product fax settings can be set from the control panel, from HP Toolbox, or from HP Director. At the
initial set-up process, the HP Fax Setup Wizard can be used to configure the settings.
In the United States and many other countries/regions, setting the time, date, and other fax header
information is a legal requirement.
ENWW
Set up fax
111
Use the control panel to set the fax time, date, and header
To use the control panel to set the date, time, and header, complete the following steps:
1.
At the control panel, press the Setup
2.
Use the arrow buttons to select the System setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Time/Date menu, and then press the OK button.
4.
Use the arrow buttons to select the 12-hour clock or 24-hour clock, and then press the OK button.
5.
Use the keypad to enter the current time.
6.
Complete one of the following:
button.
●
For the 12-hour clock, use the arrow buttons to move past the fourth character. Select 1 for
a.m. or 2 for p.m. Press the OK button.
●
For the 24-hour clock, press the OK button.
7.
Use the keypad to enter the current date. Use two digits to specify the month, day, and year. Press
the OK button.
8.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
9.
Use the arrow buttons to select the Fax header menu, and then press the OK button.
10. Use the keypad to enter your fax number and your company name or header, and then press the
OK button.
NOTE: The maximum number of characters for the fax number is 20; use up to 25 characters for
the company name.
112
Chapter 10 Fax (M1210 Series only)
ENWW
Use the HP Fax Setup Wizard
If you completed the software installation, you are ready to send faxes from your computer. If you did
not complete the fax setup process at the time you installed the software, you can complete it at any
time by using the HP Fax Setup Wizard.
Set fax time, date, and header
1.
Click Start, and then click Programs.
2.
Click HP, click the name of the product, and then click HP Fax Setup Wizard.
3.
Follow the onscreen instructions in the HP Fax Setup Wizard to set the time, date, and fax header,
as well as several other settings.
Use of common localized letters in fax headers
When using the control panel to enter your name in the header or to enter a name for a one-touch key,
speed-dial entry, or group-dial entry, press the appropriate alphanumeric button repeatedly until the
letter that you need appears. Then, press the right arrow
button to select that letter and move to the
next space. The following table shows which letters and numbers appear on each alphanumeric button.
Key number
Characters
1
1
2
ABCabc2
3
DEFdef3
4
GHIghi4
5
JKLjkl5
6
MNOmno6
7
PQRSpqrs7
8
TUVtuv8
9
WXYZwxyz9
0
0
*
()+-./,“*&@
#
space # ,
NOTE: Use the right arrow
button to move the cursor on the control panel, and use the left
arrow
button to delete characters.
ENWW
Set up fax
113
Use the phone book
You can store frequently dialed fax numbers (up to 100 entries).
Use the control panel to create and edit the fax phone book
1.
On the control panel, press the Setup
button.
2.
Use the arrow buttons to select the Phone
Book menu, and then press the OK button.
3.
Use the arrow buttons to select the Add/Edit
menu, and then press the OK button.
4.
Enter the fax number and name, and then
press the OK button.
Import or export Microsoft Outlook contacts into the fax phone
book
1.
Open HP Toolbox.
2.
Click Fax, and then click Fax Phone Book.
3.
Browse to the program phone book, and then click Import.
Use phone-book data from other programs
NOTE: Before a phone book from another program can be imported, you must use the export feature
in that other program.
HP Toolbox can import contact information from other software program phone books. The following
table shows which programs are supported for HP Toolbox.
114
Chapter 10 Fax (M1210 Series only)
ENWW
Program
Description
Microsoft Outlook
Personal Address Book (PAB) entries, Contacts entries, or both combined may be selected.
Individuals and groups from the PAB are combined with individuals from Contacts only if the
combined option is selected.
If a Contacts entry has both a home and a business fax number, two entries will be displayed. The
“name” of these two entries will be modified. “:(B)” will be added to the name in the business
entry and “:(H)” will be added to the name in the home entry.
If a duplicate entry occurs (one from Contacts and one from the PAB with the same name and fax
number), a single entry will be displayed. However, if an entry exists in the PAB with a duplicate
in Contacts, and the Contacts entry has both a business and a home fax number, all three entries
will be displayed.
Windows Address Book
The Windows Address Book (WAB), used by Outlook Express and Internet Explorer, is supported.
If an individual has both a home and a business fax number, two entries will be displayed. The
“name” of these two entries will be modified. “:(B)” will be added to the name in the business
entry and “:(H)” will be added to the name in the home entry.
Goldmine
Goldmine version 4.0 is supported. HP Toolbox imports the file last used by Goldmine.
Symantec Act!
Act! versions 4.0 and 2000 are supported. HP Toolbox imports the database last used by Act!.
Delete phone book
You can delete all phone book entries that are programmed in the product.
CAUTION: After phone book entries are deleted, they cannot be recovered.
1.
On the control panel, press the Setup
button.
2.
Use the arrow buttons to select the Phone
Book menu, and then press the OK button.
3.
Use the arrow buttons to select the Delete all
option, and then press the OK button.
4.
Press the OK button to confirm the deletion.
ENWW
Use the phone book
115
Set fax settings
Send fax settings
Set special dialing symbols and options
You can insert pauses into a fax number that you are dialing. Pauses are often needed when dialing
internationally or connecting to an outside line.
●
Insert a dialing pause: Press the Pause # button repeatedly until a comma (,) appears on the
control-panel display, indicating that the pause will occur at that point in the dialing sequence.
●
Insert a pause for dial tone: Press the Symbols * button repeatedly until W appears on the
control-panel display to have the product wait for a dial tone before dialing the remainder of the
telephone number.
●
Insert a hook flash: Press the Symbols * button repeatedly until R appears on the control-panel
display to have the product perform a hook flash.
Set a dialing prefix
A dial prefix is a number or group of numbers that are automatically added to the beginning of every
fax number you enter at the control panel or from the software. The maximum number of characters for
a dial prefix is 50.
The default setting is Off. You might want to turn this setting on and enter a prefix if, for example, you
have to dial a number such as 9 to get a telephone line outside of your company telephone system.
While this setting is activated, you can dial a fax number without the dial prefix by using manual dial.
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Send setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Dial Prefix menu, and then press the OK button.
5.
Use the arrow buttons to select the On or Off option, and then press the OK button.
6.
If you selected the On option, use the keypad to enter the prefix, and then press the OK button.
You can use numbers, pauses, and dialing symbols.
button.
Set the dial-tone detection
Normally, the product begins dialing a fax number immediately. If you are using the product on the
same line as your telephone, turn on the detect-dial-tone setting. This prevents the product from sending
a fax while someone is on the telephone.
116
Chapter 10 Fax (M1210 Series only)
ENWW
The factory-set default for detect dial tone is On for France and Hungary, and Off for all other
countries/regions.
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Send setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Detect dial tone menu, and then press the OK button.
5.
Use the arrow buttons to select the On or Off option, and then press the OK button.
button.
Set tone-dialing or pulse-dialing
Use this procedure to set the product to tone-dialing or pulse-dialing mode. The factory-set default is
Tone. Do not change this setting unless you know that the telephone line cannot use tone dialing.
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Send setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Dialing Mode menu, and then press the OK button.
5.
Use the arrow buttons to select the Tone or Pulse option, and then press the OK button to save
the selection.
button.
NOTE: The pulse-dialing option is not available in all countries/regions.
Set autoredial and the time between redials
If the product was unable to send a fax because the receiving fax machine did not answer or was busy,
the product attempts to redial based on the redial-on-busy, redial-on-no-answer, and redial-oncommunication-error options. Use the procedures in this section to turn these options on or off.
Set the redial-on-busy option
If this option is turned on, the product redials automatically if it receives a busy signal. The factory-set
default for the redial-on-busy option is On.
ENWW
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Send setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Redial if busy menu, and then press the OK button.
5.
Use the arrow buttons to select the On or Off option, and then press the OK button.
button.
Set fax settings
117
Set the redial-on-no-answer option
If this option is turned on, the product redials automatically if the receiving machine does not answer.
The factory-set default for the redial-on-no-answer option is Off.
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Send setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Redial-no answer menu, and then press the OK button.
5.
Use the arrow buttons to select the On or Off option, and then press the OK button.
button.
Set the redial-on-communication-error option
If this option is turned on, the product redials automatically if some sort of communication error occurs.
The factory-set default for the redial-on-communication-error option is On.
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Send setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Redial Comm. Error menu, and then press the OK button.
5.
Use the arrow buttons to select the On or Off option, and then press the OK button.
button.
Set light/dark and resolution
Set the default light/dark (contrast) setting
The contrast affects the lightness and darkness of an outgoing fax as it is being sent.
The default light/dark setting is the contrast that is normally applied to items that are being faxed. The
slider is set to the middle as the default setting.
118
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Send setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Def. light/dark menu, and then press the OK button.
5.
button to move the slider to the left to make the fax lighter than the original,
Use the left arrow
or use the right arrow
button to move the slider to the right to make the fax darker than the
original.
6.
Press the OK button to save the selection.
Chapter 10 Fax (M1210 Series only)
button.
ENWW
Set resolution settings
NOTE: Increasing the resolution increases the fax size. Larger faxes increase the send time and could
exceed the available memory in the product.
The factory-set default resolution setting is Fine.
Use this procedure to change the default resolution for all fax jobs to one of the following settings:
●
Standard: This setting provides the lowest quality and the fastest transmission time.
●
Fine: This setting provides a higher resolution quality than Standard that is usually appropriate
for text documents.
●
Superfine: This setting is best used for documents that mix text and images. The transmission time
is slower than the Fine setting but faster than the Photo setting.
●
Photo: This setting produces the best images, but greatly increases the transmission time.
Set the default resolution setting
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Send setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Def. Resolution menu, and then press the OK button.
5.
Use the arrow buttons to change the resolution setting.
6.
Press the OK button to save the selection.
button.
Cover-page templates
Several business and personal fax cover-page templates are available in the PC Fax Send software
program.
NOTE: Cover-sheet templates cannot be altered. While fields within the templates may be edited, the
templates themselves are fixed forms.
Customize a fax cover sheet
ENWW
1.
Open the PC Fax Send software program.
2.
In the Fax To section, provide the recipient fax number, name, and company.
3.
In the Resolution section, select a resolution setting.
4.
In the Include With Fax section, select Cover Page.
5.
Add more information in the Notes and Subject text boxes.
Set fax settings
119
6.
In the Cover Page Template drop-down box, select a template, and then select Pages in
Document Tray.
7.
Do one of the following:
●
Click Send Now to send the fax without previewing the cover page.
●
Click Preview to view the cover page prior to sending the fax.
Receive fax settings
Set fax forwarding
You can set your product to forward incoming faxes to another fax number. When the fax arrives at
your product, it is stored in the memory. The product then dials the fax number that you have specified
and sends the fax. If the product cannot forward a fax because of an error (for example, the number is
busy) and repeated redial attempts are unsuccessful, your product prints the fax.
If the product runs out of memory while receiving a fax, it terminates the incoming fax and only
forwards the pages and partial pages that have been stored in the memory.
When it is using the fax-forwarding feature, the product (rather than the computer) must be receiving
the faxes, and the answer mode must be set to Automatic.
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Recv. setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Forward fax menu, and then press the OK button.
5.
Use the arrow buttons to select the On or Off option, and then press the OK button.
6.
If you turn on the fax-forwarding feature, use the keypad to specify the fax number where the fax
is to be sent, and then press the OK button to save the selection.
button.
Set the answer mode
Depending on the situation, set the product answer mode to Automatic, TAM, Fax/Tel, or
Manual. The factory-set default is Automatic.
120
●
Automatic: The product answers incoming calls after a specified number of rings or upon
recognition of special fax tones.
●
TAM: The product does not automatically answer the call. Instead, it waits until it detects the fax
tone.
Chapter 10 Fax (M1210 Series only)
ENWW
●
Fax/Tel: The product answers incoming calls immediately. If it detects the fax tone, it processes
the call as a fax. If it does not detect the fax tone, it creates an audible ring to alert you to answer
the incoming voice call.
●
Manual: The product never answers calls. You must start the fax-receiving process yourself, either
by pressing the Send Fax
button on the control panel or by picking up a telephone that is
connected to that line and dialing 1-2-3.
To set or change the answer mode, complete the following steps:
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Recv. setup menu, and then press the OK button.
4.
Press the OK button to select the Answer mode menu.
5.
Use the arrow buttons to select the answer mode, and then press the OK button.
button.
Block or unblock fax numbers
If you do not want to receive faxes from specific people or businesses, you can block as many as 30
fax numbers by using the control panel. When you block a fax number and someone from that number
sends you a fax, the control-panel display indicates that the number is blocked, the fax does not print,
and the fax is not saved in memory. Faxes from blocked fax numbers appear in the fax activity log with
a “discarded” designation. You can unblock blocked fax numbers individually or all at one time.
NOTE: The sender of a blocked fax is not notified that the fax failed.
Complete the following steps to block or unblock fax numbers by using the control panel:
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Recv. setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Block faxes menu, and then press the OK button.
5.
To block a fax number, use the arrow buttons to select the Add entry option, and then press the
OK button. Enter the fax number exactly as it appears in the header (including spaces), and then
press the OK button. Enter a name for the blocked number, and then press the OK button.
button.
To unblock a single fax number, use the arrow buttons to select the Delete entry option, and
then press the OK button. Use the arrow buttons to select the fax number that you want to delete,
and then press the OK button to confirm the deletions.
To unblock all blocked fax numbers, use the arrow buttons to select the Clear all option, and then
press the OK button. Press the OK button again to confirm the deletions.
Set the number of rings-to-answer
When the answer mode is set to Automatic, the product rings-to-answer setting determines the
number of times the telephone rings before the product answers an incoming call.
ENWW
Set fax settings
121
If the product is connected to a line that receives both fax and voice calls (a shared line) and that also
uses an answering machine, you might need to adjust the rings-to-answer setting. The number of ringsto-answer for the product must be greater than the rings-to-answer on the answering machine. This
allows the answering machine to answer the incoming call and record a message if it is a voice call.
When the answering machine answers the call, the product listens to the call and automatically
answers it if it detects fax tones.
The default setting for rings-to-answer is five for the U.S. and Canada, and two for other countries/
regions.
Use the following table to determine the number of rings-to-answer to use.
Type of telephone line
Recommended rings-to-answer setting
Dedicated fax line (receiving only fax calls)
Set to a number of rings within the range shown on the
control-panel display. (The minimum and maximum number of
rings allowed varies by country/region.)
One line with two separate numbers and a ring-pattern
service
One or two rings. (If you have an answering machine or
computer voicemail for the other telephone number, make sure
that the product is set to a greater number of rings than the
answering system. Also, use the distinctive-ring feature to
differentiate between voice and fax calls.)
Shared line (receiving both fax and voice calls) with only an
attached telephone
Five rings or more.
Shared line (receiving both fax and voice calls) with an
attached answering machine or computer voicemail
Two rings more than the answering machine or computer
voicemail.
To set or change the number of rings-to-answer, use the following steps:
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Recv. setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Rings to answer menu, and then press the OK button.
5.
Use the keypad to enter the number of rings-to-answer, and then press the OK button.
button.
Set distinctive ring
Ring-pattern or distinctive-ring service is available through some local telephone companies. The service
allows you to have more than one telephone number on a single line. Each telephone number has a
unique ring pattern, so that you can answer voice calls and the product can answer fax calls.
If you subscribe to a ring-pattern service with a telephone company, you must set the product to answer
the correct ring pattern. Not all countries/regions support unique ring patterns. Contact the telephone
company to determine if this service is available in your country/region.
NOTE: If you do not have ring-pattern service and you change the ring-pattern settings to something
other than the default, All Rings, the product might not be able to receive faxes.
122
Chapter 10 Fax (M1210 Series only)
ENWW
The settings are as follows:
●
All Rings: The product answers any calls that come through the telephone line.
●
Single: The product answers any calls that produce a single-ring pattern.
●
Double: The product answers any calls that produce a double-ring pattern.
●
Triple: The product answers any calls that produce a triple-ring pattern.
●
Double&Triple: The product answers any calls that produce a double-ring or triple-ring pattern.
To change ring patterns for call answering, complete the following steps:
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Recv. setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Answer Ring Type menu, and then press the OK button.
5.
Use the arrow buttons to select the ring pattern that you want, and then press the OK button.
6.
After product installation is complete, ask someone to send a fax to you in order to verify that the
ring-pattern service is working correctly.
button.
Use autoreduction for incoming faxes
If the fit-to-page option is turned on, the product automatically reduces long faxes up to 75% to fit the
information on the default paper size (for example, the fax is reduced from legal to letter size).
If the fit-to-page option is turned off, long faxes print at full size on multiple pages. The factory-set
default for incoming fax autoreduction is On.
If you have the Stamp faxes option turned on, you might also want to turn on autoreduction. This
reduces the size of the incoming faxes slightly, and prevents the page-stamp from forcing a fax onto
two pages.
NOTE: Make sure that the default media size setting matches the size of the media that is loaded in
the tray.
ENWW
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Recv. setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Fit to page menu, and then press the OK button.
5.
Use the arrow buttons to select the On or Off option, and then press the OK button to save the
selection.
button.
Set fax settings
123
Set fax reprint settings
The default fax reprint setting is On. To change this setting from the control panel, complete the
following steps:
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Recv. setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Reprint faxes menu, and then press the OK button.
5.
Use the arrow buttons to select the On or Off option, and then press the OK button.
button.
Set the silence-detect mode
This setting controls whether or not you can receive faxes from older-model fax machines that do not
emit a fax signal during fax transmissions. At the time of this publication, these silent-model fax
machines represented very few of the fax machines in use. The default setting is Off. The silence-detect
mode setting should be changed only if you regularly receive faxes from someone who uses an oldermodel fax machine.
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Recv. setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Silence detect menu, and then press the OK button.
5.
Use the arrow buttons to select the On or Off option, and then press the OK button to save the
selection.
button.
Set the fax volume
Control the volume of the fax sounds from the control panel. You can make changes to the following
sounds:
●
The fax sounds that are associated with incoming and outgoing faxes
●
The ring for incoming faxes
The factory-set default for the fax-sounds volume is Soft.
Set the alert volume, phone-line volume, and ring volume
124
1.
Press the Setup
2.
Use the arrow buttons to select the System setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Volume settings menu, and then press the OK button.
4.
Use the arrow buttons to select the Alarm volume menu, the Phoneline volume menu, or the
Ring volume menu, and then press the OK button.
button.
Chapter 10 Fax (M1210 Series only)
ENWW
5.
Use the arrow buttons to select the Off, Soft, Medium, or Loud setting.
6.
Press the OK button to save the selection.
Set stamp-received faxes
The product prints the sender identification information at the top of each received fax. You can also
choose to stamp the incoming fax with your own header information to confirm the date and time that
the fax was received. The factory-set default for stamp-received faxes is Off.
NOTE: Turning on the stamp-received setting might increase the page size and cause the product to
print a second page.
NOTE: This option applies only to received faxes that the product prints.
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Recv. setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Stamp faxes menu, and then press the OK button.
5.
Use the arrow buttons to select the On or Off option, and then press the OK button to save the
selection.
button.
Set the private receive feature
NOTE: The private receive feature does not affect the reprint last fax feature. To limit access to all
received faxes, make sure that the Reprint faxes setting is set to Off.
When the private-receive feature is activated, received faxes are stored in memory. A personal
identification number (PIN) is required to print the stored faxes.
Turn on the private receive feature
ENWW
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Recv. setup menu, and then press the OK button.
4.
Use the arrow buttons to select the Private receive menu, and then press the OK button.
5.
Use the arrow buttons to select the On option, and then press the OK button.
6.
Use the keypad to enter the product security password, and then press the OK button.
7.
To confirm the product security password, use the keypad to re-enter the product security
password, and then press the OK button.
button.
Set fax settings
125
Turn off the private receive feature
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the keypad to enter the product security password, and then press the OK button.
4.
Use the arrow buttons to select the Fax Recv. setup menu, and then press the OK button.
5.
Use the arrow buttons to select the Private receive menu, and then press the OK button.
6.
Use the arrow buttons to select the Off option, and then press the OK button.
button.
If any unprinted faxes exist in the fax memory, the product will print the faxes and then erase them
from memory.
Set fax polling
If someone else has set up a fax to be polled, you can request that the fax be sent to your product. (This
is known as polling another machine).
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax functions menu, and then press the OK button.
3.
Use the arrow buttons to select the Polling receive option, and then press the OK button.
button.
The product dials the other fax machine and requests the fax.
126
Chapter 10 Fax (M1210 Series only)
ENWW
Use fax
Fax software
Supported fax programs
The PC fax program that came with the product is the only PC fax program that works with the product.
In order to continue to use a PC fax program previously installed on the computer, it must be used with
the modem that is already connected to the computer; it will not function through the product modem.
Cancel a fax
Use these instructions to cancel a single fax that is currently dialing or a fax that is being transmitted or
received.
Cancel the current fax
Press the Cancel
button on the control panel. Any pages that have not been transmitted are
canceled. Pressing the Cancel
button also stops group-dial jobs.
Cancel a pending fax job
Use this procedure to cancel a fax job in the following situations:
●
The product is waiting to redial after encountering a busy signal, an unanswered call, or a
communication error.
●
The fax is scheduled to be sent at a future time.
Use the following steps to cancel a fax job by using the Fax Job status menu:
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax Job status menu, and then press the OK button.
3.
Use the arrow buttons to scroll through pending jobs until you reach the job that you want to clear.
4.
Press the OK button to select the job that you want to cancel.
5.
Press the OK button to confirm that you want to cancel the job.
button.
Delete faxes from memory
Use this procedure only if you are concerned that someone else has access to your product and might
try to reprint faxes from the memory.
ENWW
Use fax
127
CAUTION: In addition to clearing the reprint memory, this procedure clears any fax that is currently
being sent, unsent faxes that are pending redial, faxes that are scheduled to be sent at a future time,
and faxes that are not printed or forwarded.
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax functions menu, and then press the OK button.
3.
Use the arrow buttons to select the Clear saved faxs option, and then press the OK button.
4.
Press the OK button to confirm the deletion.
button.
Use fax on a DSL, PBX, or ISDN system
HP products are designed specifically for use with traditional analog phone services. They are not
designed to work on DSL, PBX, ISDN lines, or VoIP services, but they might work with the proper setup
and equipment.
NOTE: HP recommends discussing DSL, PBX, ISDN, and VoIP setup options with the service provider.
The HP LaserJet product is an analog device that is not compatible with all digital phone environments
(unless a digital-to-analog converter is used). HP does not guarantee that the product will be compatible
with digital environments or digital-to-analog converters.
DSL
A digital subscriber line (DSL) uses digital technology over standard copper telephone wires. This
product is not directly compatible with digital signals. However, if the configuration is specified during
DSL setup, the signal can be separated so that some of the bandwidth is used to transmit an analog
signal (for voice and fax) while the remaining bandwidth is used to transmit digital data.
NOTE: Not all faxes are compatible with DSL services. HP does not guarantee that the product will
be compatible with all DSL service lines or providers.
The DSL modem requires a high-pass filter. The service provider typically provides a low-pass filter, for
normal telephone wiring.
NOTE: Contact the DSL provider for more information or for assistance.
PBX
The product is an analog device that is not compatible in all digital phone environments. Digital-toanalog filters or converters may be needed for faxing functionality. If faxing issues occur in a PBX
environment, it might be necessary to contact the PBX provider for assistance. HP does not guarantee
that the product will be compatible with digital environments or digital-to-analog converters.
Contact the PBX provider for more information and for assistance.
ISDN
Contact the ISDN provider for more information and for assistance.
128
Chapter 10 Fax (M1210 Series only)
ENWW
Use fax on a VoIP service
Voice over internet protocol (VoIP) services are often not compatible with fax machines unless the
provider explicitly states that it supports fax over IP services.
If the product experiences problems getting a fax to work on a VoIP network, verify that all cables and
settings are correct. Decreasing the fax-speed setting might allow the product to send a fax over a VoIP
network.
If faxing problems continue, contact the VoIP provider.
Fax memory
Fax memory is retained when there is a loss of power
The flash memory protects against data loss when a power failure occurs. Other fax devices store fax
pages in either normal RAM or short-term RAM. Normal RAM immediately loses data when power is
lost, while short-term RAM loses data about 60 minutes after a power failure occurs. Flash memory can
maintain its data for years without power applied.
Send a fax
Fax from the flatbed scanner
1.
Place the document face-down on the scanner
glass.
2.
Press the Setup
3.
Select the Phone Book menu, and then press
the OK button.
4.
From the list, select the phone book entry. If no
entry exists, use the keypad on the control
panel to dial the number.
5.
On the control panel, press the Send Fax
button. The product starts the fax job.
ENWW
button.
Use fax
129
Fax from the document feeder
1.
Insert the originals into the document feeder
face-up.
NOTE: The document feeder capacity is up
to 35 sheets of 75 g/m2 or 20 lb media.
CAUTION: To prevent damage to the
product, do not use an original that contains
correction tape, correction fluid, paper clips,
or staples. Also, do not load photographs,
small originals, or fragile originals into the
document feeder.
2.
Adjust the guides until they are snug against
the paper.
3.
Press the Setup
4.
Select the Phone Book menu, and then press
the OK button.
5.
From the list, select the phone book entry. If no
entry exists, use the keypad on the control
panel to dial the number.
6.
On the control panel, press the Send Fax
button. The product starts the fax job.
button.
Manual dial faxing
Usually, the product dials after you press the Send Fax
button. At times, however, you might want
the product to dial each number as you press it. For example, if you are charging your fax call to a
calling card, you might need to dial the fax number, wait for the acceptance tone of your telephone
130
Chapter 10 Fax (M1210 Series only)
ENWW
company, and then dial the calling card number. When dialing internationally, you might need to dial
part of the number and then listen for dial tones before continuing to dial.
Send a fax to a group manually (ad hoc faxing)
Use the following instructions to send a fax to a group of recipients:
1.
Load the document into the document feeder input tray.
2.
Press the Setup
3.
Select the Phone Book menu, and then press the OK button.
4.
From the list, select the phone book entry. If no entry exists, use the keypad on the control panel to
dial the number.
5.
To continue dialing numbers, repeat steps 3 and 4. If you are finished dialing numbers, go to the
next step.
6.
Press the Send Fax
7.
If you have more pages to scan, press 1 to select the Yes option, and then repeat step 6 for each
page of the fax job. If you are finished, press 2 to select the No option.
button.
button.
The product sends the fax to each fax number. If a number in the group is busy or does not answer, the
product redials that number based on the redial setting. If all redial attempts fail, the product updates
the fax activity log by adding the error, and then it proceeds to the next number in the group.
Manual redial
1.
Load the document into the document feeder.
2.
On the control panel, press the Redial
3.
Press the Send Fax
4.
If you have more pages to scan, press 1 to select the Yes option, and then repeat step 3 for each
page of the fax job. If you are finished, press 2 to select the No option.
button.
button.
The product sends the fax to the number that it redialed. If the number is busy or does not answer, the
product redials the number based on its redial setting. If all redial attempts fail, the product updates the
fax activity log by adding the error.
ENWW
Use fax
131
Send a fax from the software
The following information provides basic instructions for sending faxes by using the software that came
with the product. All other software-related topics are covered in the software Help, which can be
opened from the software-program Help menu.
You can fax electronic documents from a computer if you meet the following requirements:
●
The product is connected directly to the computer.
●
The product software is installed on the computer.
●
The computer operating system is Microsoft Windows XP, Windows Vista, or Mac OS X 10.4,
10.5, 10.6, or later.
Send a fax from the software (Windows XP or Vista)
The procedure to send a fax varies according to your specifications. The most typical steps follow.
1.
Click Start, click Programs (or All Programs in Windows XP), and then click HewlettPackard.
2.
Click the product name, and then click Send fax. The fax software appears.
3.
Enter the fax number of one or more recipients.
4.
Load the document in the document feeder.
5.
Include a cover page. (This step is optional.)
6.
Click Send Now.
Send a fax from the software (Mac OS X 10.4 and later)
Using Mac OS X, you can choose between two methods of sending faxes from the product software.
To send a fax by using HP Director complete the following steps:
1.
Load the document into the document feeder.
2.
Open HP Director by clicking the icon in the dock, and then click Fax. The Apple print dialog
appears.
3.
Select Fax PDF from the PDF pop-up menu.
4.
Enter the fax number of one or more recipients under To.
5.
Select the product under Modem.
6.
Click Fax.
To send a fax by printing to a fax driver, complete the following steps:
132
1.
Open the document that you want to fax.
2.
Click File and then click Print.
Chapter 10 Fax (M1210 Series only)
ENWW
3.
Select Fax PDF from the PDF pop-up menu.
4.
Enter the fax number of one or more recipients under To.
5.
Select the product under Modem.
6.
Click Fax.
Send a fax from a third-party software program, such as Microsoft Word (all operating
systems)
1.
Open a document in a third-party program.
2.
Click the File menu, and then click Print.
3.
Select the fax print driver from the printer driver drop-down list. The fax software appears.
4.
Complete one of the following procedures:
●
●
ENWW
Windows
a.
Enter the fax number of one or more recipients.
b.
Include a cover page. (This step is optional.)
c.
Include any pages loaded at the product. (This step is optional.)
d.
Click Send Now.
Macintosh
a.
Select Fax PDF from the PDF pop-up menu.
b.
Enter the fax number of one or more recipients.
c.
Select the product under Modem.
d.
Click Fax.
Use fax
133
Send a fax by dialing from a telephone connected to the fax line
Occasionally, you might want to dial a fax number from a telephone that is connected to the same line
as the product. For example, if you are sending a fax to a person whose device is in the manual
receive mode, you can precede the fax with a voice call to let that person know that the fax is coming.
NOTE: The telephone must be connected to the product "telephone" port
.
1.
Load the document into the document feeder.
2.
Pick up the handset of a telephone that is connected to the same line as the product. Dial the fax
number by using the telephone keypad.
3.
When the recipient answers, instruct the person to start the fax machine.
4.
button, wait until Connecting appears on
When you hear the fax tones, press theSend Fax
the control-panel display, and then hang up the telephone.
Schedule a fax to be sent later
Use the product control panel to schedule a fax to be sent automatically at a future time to one or more
people. When this procedure is completed, the product scans the document into memory and then
returns to the Ready state.
NOTE: If the product cannot transmit the fax at the scheduled time, that information is indicated on
the fax error report (if that option is turned on) or recorded in the fax activity log. The transmittal might
not be initiated because the fax-sending call is not answered, or because a busy signal stops the redial
attempts.
If a fax has been scheduled to be sent at a future time but it requires updating, send the additional
information as another job. All faxes that are scheduled to go to the same fax number at the same time
are delivered as individual faxes.
1.
134
Load the document into the document feeder.
Chapter 10 Fax (M1210 Series only)
ENWW
2.
On the control panel, press the Setup
button.
3.
Use the arrow buttons to select the Fax
functions menu, and then press the OK
button.
4.
Use the arrow buttons to select the Send fax
later menu, and then press the OK button.
5.
Use the keypad to enter the time.
6.
If the product is set to the 12-hour time mode,
use the arrow buttons to move the cursor past
the fourth character to set A.M. or P.M. Select
1 for A.M. or select 2 for P.M., and then press
the OK button. If the product is set to the 24hour time mode, press the OK button.
7.
Press the OK button to accept the default date
or use the keypad to enter the date, and then
press the OK button.
8.
Enter the fax number.
NOTE: This feature does not support
undefined (ad hoc) groups.
9.
Press the OK button or the Send Fax
button. The product scans the document into
memory and sends it at the designated time.
Use access codes, credit cards, or calling cards
To use access codes, credit cards, or calling cards, dial manually to allow for pauses and dialing
codes.
Send faxes internationally
To send a fax to an international destination, dial manually to allow for pauses and international
dialing codes.
ENWW
Use fax
135
Receive a fax
Print a fax
When the product receives a fax transmission, it prints the fax (unless the private-receive feature is
enabled) and also stores it automatically to flash memory.
Print a stored fax when the private receive feature is on
To print stored faxes, you must provide the private-receive PIN. After the product prints the stored faxes,
the faxes are deleted from memory.
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the keypad to enter the product security PIN, and then press the OK button.
4.
Use the arrow buttons to select the Fax Recv. setup menu, and then press the OK button.
5.
Use the arrow buttons to select the Private receive menu, and then press the OK button.
6.
Use the arrow buttons to select the Print faxes option, and then press the OK button.
button.
Reprint a fax
If you want to reprint a fax because the print cartridge was empty or if the fax was printed on the
wrong type of media, you can try to reprint it. The amount of memory that is available determines the
actual number of faxes that are stored for reprinting. The most recent fax prints first; the oldest fax that
is in storage prints last.
These faxes are stored continuously. Reprinting them does not clear them from the memory.
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax functions menu, and then press the OK button.
3.
Use the arrow buttons to select the Reprint last option, and then press the OK button. The
product begins reprinting the most recently printed fax.
button.
NOTE: To stop the printing at any time, press the Cancel
button.
CAUTION: If the Reprint faxes setting is set to Off, misprinted or faded faxes cannot be
reprinted.
136
Chapter 10 Fax (M1210 Series only)
ENWW
Receive faxes when fax tones are audible on the phone line
If you have a telephone line that receives both fax and telephone calls, and you hear fax tones when
you answer the telephone, you can start the receiving process in one of two ways:
button on the control panel.
●
If you are close to the product, press the Send Fax
●
If not, press 1-2-3 in sequence on the telephone keypad, listen for fax transmission sounds, and
then hang up.
NOTE: In order for the second method to work, the Extension Phone setting must be set to Yes.
Receive faxes to a computer
NOTE: Receiving faxes by using a computer is not supported for Macintosh.
Receiving faxes to a computer is available only if a full software installation was performed during
initial product setup.
To receive faxes to your computer, turn on the receive-to-PC setting in the software.
1.
Open HP Toolbox.
2.
Select the product.
3.
Click Fax.
4.
Click Fax Tasks.
5.
Under Fax Receive Mode, select Receive faxes to this computer.
Turn off the receive-to-PC setting from the control panel
The receive-to-PC setting can be activated only from one computer. If for any reason that computer is no
longer available, you can use the following procedure to turn the receive-to-PC setting off from the
control panel.
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax functions menu, and then press the OK button.
3.
Use the arrow buttons to select the Stop Recv to PC option, and then press the OK button.
button.
View a new fax when in receive to PC mode
ENWW
1.
Open HP Toolbox.
2.
Select the product.
3.
Click Fax.
4.
Click Fax Receive Log.
5.
In the Fax Image column, click the “view” link of the fax that you want to view.
Use fax
137
Solve fax problems
Fax troubleshooting checklist
Tips for fax troubleshooting:
●
Print the menu map from the Reports menu to show the control-panel menus and available
settings.
●
Try to send or receive a fax after implementing each solution.
●
Disconnect all devices except for the product. Verify that the telephone cord from the product is
plugged directly into the wall telephone jack.
1.
Verify that the product firmware is current:
a.
Print a configuration page from the Reports menu.
b.
Go to www.hp.com/support/ljm1210series, and select the operating system that you are
using.
c.
Scroll to the firmware table, and then compare the current version listed with the version
listed on the configuration page. If versions are different, download the newest firmware.
d.
Print a new configuration page to verify that the firmware is current.
2.
Verify that the telephone cord is plugged into the correct port.
3.
Verify that the fax is set up. Use the control panel or the HP Fax Setup Wizard to configure the fax
time, date, and fax header information.
4.
Check the phone line.
a.
Unplug the telephone cord from the product.
b.
Plug the telephone cord into a telephone and verify that there is a dial tone.
c.
Reconnect the telephone cord into the correct port on the product.
5.
If using a DSL service, check the installation and features. The DSL modem requires a high-pass
filter. The service provider typically provides a low-pass filter, for normal telephone wiring.
6.
If using a VoIP service, check the installation and features. The VoIP service might not support fax
over IP. If fax over IP is supported, change the Fax Speed setting to Slow(V.29).
7.
If you cannot send or receive faxes, do the following:
a.
Change the error correction settings.
NOTE: Changing these settings might reduce image quality.
b.
138
Change the Fax Speed setting to Medium(V.17) or Slow(V.29).
Chapter 10 Fax (M1210 Series only)
ENWW
Fax error messages
Alert and warning messages appear temporarily and might require you to acknowledge the message
by pressing the OK button to resume or by pressing the Cancel
button to cancel the job. With
certain warnings, the job might not complete or the print quality might be affected. If the alert or
warning message is related to printing and the auto-continue feature is on, the product will attempt to
resume printing the job after the warning has appeared for 10 seconds without acknowledgement.
Alert and warning messages
Control panel message
Description
Recommended action
Comm. error
A fax communication error occurred between
the product and the sender or receiver.
Allow the product to retry sending the fax.
Unplug the product telephone cord from the
wall, plug in a telephone, and try making a
call. Plug the product phone cord into a jack
for another phone line.
Try a different phone cord.
If the error persists, contact HP. See
www.hp.com/support/ljm1210series or the
support flyer that came in the product box.
Fax delayed
Fax memory is full.
Cancel the fax by pressing the Cancel
button. Resend the fax. You might need to
send the fax in multiple sections if the error
occurs again.
The fax line to which you were sending a fax
was busy. The product has canceled sending
the fax.
Call the recipient to ensure that the fax
machine is on and ready.
Send memory full
Fax is busy
Canceled send
Check that you are dialing the correct fax
number.
Check that the Redial if busy option is
enabled.
Check for a dial tone on the phone line by
pressing the Send Fax
button.
Make sure that the phone is working by
disconnecting the product, plugging in a
telephone to the phone line, and making a
voice call.
Plug the product phone cord into a jack for
another phone line, and then try sending the
fax again.
Try a different phone cord.
If the error persists, contact HP. See
www.hp.com/support/ljm1210series or the
support flyer that came in the product box.
ENWW
Solve fax problems
139
Control panel message
Description
Recommended action
Fax is busy
The fax line to which you were sending a fax
was busy. The product automatically redials
the busy number.
Allow the product to retry sending the fax.
Redial pending
Call the recipient to ensure that the fax
machine is on and ready.
Check that you are dialing the correct fax
number.
Check for a dial tone on the phone line by
pressing the Send Fax
button.
Make sure that the phone is working by
disconnecting the product, plugging in a
telephone to the phone line, and making a
voice call.
Plug the product phone cord into a jack for
another phone line, and try sending the fax
again.
Try a different phone cord.
If the error persists, contact HP. See
www.hp.com/support/ljm1210series or the
support flyer that came in the product box.
Fax memory full
Canceling recv.
Fax memory full
Canceling send
During the fax transmission, the product ran
out of memory. Only the pages that fit into
memory will be printed.
Print all of the faxes, and then have the
sender resend the fax. Have the sender
divide the fax job into multiple jobs before
resending. Cancel all fax jobs or clear the
faxes from memory.
During the fax job, the memory filled. All
pages of the fax have to be in memory for a
fax job to work correctly. Only the pages
that fit into memory were sent.
Print all received faxes or wait until all
pending faxes are sent.
Ask the sender to send the fax again.
Cancel all fax jobs or clear the faxes from
memory.
140
Chapter 10 Fax (M1210 Series only)
ENWW
Control panel message
Description
Recommended action
Fax recv. error
An error occurred while trying to receive a
fax.
Ask the sender to resend the fax.
Try faxing back to the sender or another fax
machine.
Check for a dial tone on the phone line by
pressing the Send Fax
button.
Check that the telephone cord is securely
connected by unplugging and replugging the
cord.
Make sure that you are using the telephone
cord that came with the product.
Make sure that the phone is working by
disconnecting the product, plugging in a
telephone to the phone line, and making a
voice call.
Decrease the fax speed. Ask the sender to
resend the fax.
Turn off error-correction mode. Ask the
sender to resend the fax.
Connect the product to a different phone
line.
If the error persists, contact HP. See
www.hp.com/support/ljm1210series or the
support flyer that came in the product box.
ENWW
Solve fax problems
141
Control panel message
Description
Recommended action
Fax Send error
An error occurred while trying to send a fax.
Try resending the fax.
Try faxing to another fax number.
Check for a dial tone on the phone line by
pressing the Send Fax
button.
Check that the telephone cord is securely
connected by unplugging and replugging the
cord.
Make sure that you are using the telephone
cord that came with the product.
Make sure that the phone is working by
disconnecting the product, plugging in a
telephone to the phone line, and making a
voice call.
Connect the product to a different phone
line.
Set the fax resolution to Standard instead
of the default of Fine.
If the error persists, contact HP. See
www.hp.com/support/ljm1210series or the
support flyer that came in the product box.
Invalid entry
Invalid data or response.
Correct the entry.
No dial tone
The product could not detect a dial tone.
Check for a dial tone on the phone line by
pressing the Send Fax
button.
Unplug the telephone cord from both the
product and the wall and replug the cord.
Make sure that you are using the telephone
cord that came with the product.
Unplug the product telephone cord from the
wall, plug in a telephone, and try making a
voice call.
Make sure that the phone cord from the wall
telephone jack is plugged into the line
port.
Plug the product phone cord into a jack for
another phone line.
If the error persists, contact HP. See
www.hp.com/support/ljm1210series or the
support flyer that came in the product box.
No document sent
142
The product did not scan any pages, or it
did not receive any pages from the computer
to transmit a fax.
Chapter 10 Fax (M1210 Series only)
Try sending the fax again.
ENWW
Control panel message
Description
Recommended action
No fax answer.
Attempts to redial a fax number failed, or the
Redial-no answer option was turned off.
Call the recipient to ensure that the fax
machine is on and ready.
Canceled send
Check that you are dialing the correct fax
number.
Check that the redial option is enabled.
Unplug the telephone cord from both the
product and the wall and replug the cord.
Unplug the product telephone cord from the
wall, plug in a telephone, and try making a
voice call.
Make sure that the phone cord from the wall
telephone jack is plugged into the line
port.
Plug the product phone cord into a jack for
another phone line.
If the error persists, contact HP. See
www.hp.com/support/ljm1210series or the
support flyer that came in the product box.
ENWW
Solve fax problems
143
Control panel message
Description
Recommended action
No fax answer.
The receiving fax line did not answer. The
product attempts to redial after a few
minutes.
Allow the product to retry sending the fax.
Redial pending
Call the recipient to ensure that the fax
machine is on and ready.
Check that you are dialing the correct fax
number.
If the product continues to redial, unplug the
product telephone cord from the wall, plug in
a telephone, and try making a voice call.
Make sure that the phone cord from the wall
telephone jack is plugged into the line
port.
Plug the product phone cord into a jack for
another phone line.
Try a different phone cord.
If the error persists, contact HP. See
www.hp.com/support/ljm1210series or the
support flyer that came in the product box.
No fax detected
The product answered the incoming call but
did not detect that a fax machine was
calling.
Allow the product to retry receiving the fax.
Try a different phone cord.
Plug the product phone cord into a jack for
another phone line.
If the error persists, contact HP. See
www.hp.com/support/ljm1210series or the
support flyer that came in the product box.
144
Chapter 10 Fax (M1210 Series only)
ENWW
Fax logs and reports
Use the following instructions to print fax logs and reports:
Print all fax reports
Use this procedure to print all of the following reports at one time:
●
Fax Activity log
●
Phone Book report
●
Config report
●
Block Fax list
1.
On the control panel, press the Setup
button.
2.
Use the arrow buttons to select the Reports
menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax
Reports menu, and then press the OK button.
4.
Use the arrow buttons to select the All fax
reports option, and then press the OK button.
The product exits the menu settings and prints
the reports.
Print individual fax reports
ENWW
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Reports menu, and then press the OK button.
button.
Solve fax problems
145
3.
Use the arrow buttons to select the Fax Reports menu, and then press the OK button.
4.
Use the arrow buttons to select the report to be printed, and then press the OK button. The product
exits the menu settings and prints the report.
NOTE: If you selected the Fax Activity log report and pressed the OK button, press the OK
button again to select the Print log now option. The product exits the menu settings and prints
the log.
Set the fax activity log to print automatically
You can decide whether or not you want the fax log to print automatically after every 40 entries. The
factory-set default is On. Use the following steps to set the fax activity log to print automatically:
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Reports menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Reports menu, and then press the OK button.
4.
Use the arrow buttons to select the Fax Activity log menu, and then press the OK button.
5.
Use the arrow buttons to select the Auto Log Print menu, and then press the OK button.
6.
Use the arrow buttons to select the On option, and then press the OK button to confirm the
selection.
button.
Set the fax error report
A fax error report is a brief report that indicates the product experienced a fax job error. It can be set
to print after the following events:
●
Every fax error (the factory-set default)
●
Send fax error
●
Receive fax error
●
Never
NOTE: If you select Never, you will have no indication that a fax failed to be transmitted unless you
print a fax activity log.
146
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Reports menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Reports menu, and then press the OK button.
4.
Use the arrow buttons to select the Fax Error report menu, and then press the OK button.
5.
Use the arrow buttons to select the option for when you want the fax error reports to be printed.
6.
Press the OK button to save the selection.
Chapter 10 Fax (M1210 Series only)
button.
ENWW
Set the fax confirmation report
A confirmation report is a brief report that indicates the product successfully sent or received a fax job.
It can be set to print after the following events:
●
Every fax job
●
Send fax
●
Receive fax
●
Never (the factory-set default)
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Reports menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Reports menu, and then press the OK button.
4.
Use the arrow buttons to select the Fax Confirmation menu, and then press the OK button.
5.
Use the arrow buttons to select the option for when you want the fax error reports to be printed.
6.
Press the OK button to save the selection.
button.
Include the first page of each fax on the fax confirmation, fax error, and last
call reports
If this option is turned on and the page image still exists in the product memory, the fax configuration,
fax error, and last call reports include a thumbnail (50% reduction) of the first page of the most recent
fax that was sent or received. The factory-set default for this option is On.
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Reports menu, and then press the OK button.
3.
Use the arrow buttons to select the Fax Reports menu, and then press the OK button.
4.
Use the arrow buttons to select the Include 1st page menu, and then press the OK button.
5.
Use the arrow buttons to select the On option, and then press the OK button to confirm the
selection.
button.
Change error correction and fax speed
Set the fax-error-correction mode
Usually, the product monitors the signals on the telephone line while it is sending or receiving a fax. If
the product detects an error during the transmission and the error-correction setting is On, the product
can request that the portion of the fax be resent. The factory-set default for error correction is On.
You should turn off error correction only if you are having trouble sending or receiving a fax, and you
are willing to accept the errors in the transmission. Turning off the setting might be useful when you are
ENWW
Solve fax problems
147
trying to send a fax overseas or receive one from overseas, or if you are using a satellite telephone
connection.
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the All faxes menu, and then press the OK button.
4.
Use the arrow buttons to select the Error correction menu, and then press the OK button.
5.
Use the arrow buttons to select the On or Off option, and then press the OK button to save the
selection.
button.
Change the fax speed
The fax-speed setting is the modem protocol that the product uses to send faxes. It is the worldwide
standard for full-duplex modems that send and receive data across telephone lines at up to 33,600 bits
per second (bps). The factory-set default for the fax-speed setting is Fast(V.34). In some countries/
regions, the factory-set default may be different to optimize transmission.
You should change the setting only if you are having trouble sending a fax to or receiving a fax from a
particular device. Decreasing the fax speed might be useful when you are trying to send a fax
overseas, or receive one from overseas, or if you are using a satellite telephone connection.
1.
On the control panel, press the Setup
2.
Use the arrow buttons to select the Fax setup menu, and then press the OK button.
3.
Use the arrow buttons to select the All faxes menu, and then press the OK button.
4.
Use the arrow buttons to select the Fax Speed menu, and then press the OK button.
5.
Use the arrow buttons to select a speed setting, and then press the OK button.
button.
Problems sending faxes
The document stops feeding in the middle of faxing.
Cause
Solution
The maximum length of a page that you can load is 355 mm
(14 inches). Faxing of a longer page stops at this
measurement.
Print the document on shorter media.
If the item is too small, it can jam inside the document feeder.
The minimum page size for the document feeder is 148 x
105 mm (5.83 x 4.13 inches).
If no jam exists and less than one minute has elapsed, wait a
moment before pressing the Cancel
button. If a jam exists,
remove the jam. Then, resend the job.
If a jam exists, remove the jam. Then, resend the job.
148
Chapter 10 Fax (M1210 Series only)
ENWW
Faxes stop during sending.
Cause
Solution
The receiving fax machine might be malfunctioning.
Try sending to another fax machine.
The telephone line might not be working.
Do one of the following:
A communication error might be interrupting the fax job.
●
Turn up the volume on the product, and then press the
Send Fax
button on the control panel. If you hear a
dial tone, the telephone line is working.
●
Disconnect the product from the jack in the wall, and
then connect a telephone to the jack. Try to make a
telephone call to verify that the telephone line is working.
Change the redial-on-communication-error setting to On.
The product is receiving faxes but is not sending them.
Cause
Solution
If the product is on a digital system, the system might be
generating a dial tone that the product cannot detect.
Disable the detect-dial-tone setting.
A poor telephone connection might exist.
Try again later.
The receiving fax machine might be malfunctioning.
Try sending to another fax machine.
The telephone line might not be working.
Do one of the following:
If the error persists, contact the system service provider.
●
Turn up the volume on the product and press the Send
Fax
button on the control panel. If a dial tone exists,
the telephone line is working.
●
Disconnect the product from the telephone jack and
connect a telephone. Try to make a telephone call to
verify that the telephone line is working.
Outgoing fax calls continue to be dialed.
Cause
Solution
The product automatically redials a fax number if the redial
options are set to On.
To stop the product from redialing a fax, press the Cancel
button. Or change the redial setting.
Sent faxes are not arriving at the receiving fax machine.
ENWW
Cause
Solution
The receiving fax machine might be off or might have an error
condition, such as being out of paper.
Call the recipient to verify that the fax machine is on and
ready to receive faxes.
Solve fax problems
149
Sent faxes are not arriving at the receiving fax machine.
Cause
Solution
The originals might be incorrectly loaded.
Verify that the original documents are correctly loaded into the
document feeder.
A fax might be in memory because it is waiting to redial a
busy number, other jobs that are ahead of it are waiting to be
sent, or the fax is set up for a delayed send.
If a fax job is in memory for any of these reasons, an entry for
the job appears in the fax log. Print the fax activity log and
check the Status column for jobs that show a Pending
designation.
The control panel shows a low-memory error.
Cause
Solution
The fax might be too large, or the resolution might be too
high.
Try one of the following:
●
Divide a large fax into smaller sections, and then fax
them individually.
●
Clear stored faxes to make more memory available for
outgoing faxes.
●
Configure the outgoing fax as a delayed fax, and then
verify that it will send completely.
●
Make sure that the product is using the lowest resolution
setting (Standard).
Faxes are transmitting very slowly.
Cause
Solution
The fax might be very complex, such as one with many
graphics.
Complex faxes take longer to be sent or received. Breaking
longer faxes into multiple jobs and decreasing the resolution
can increase the transmission speed.
The receiving fax machine might have a slow modem speed.
The product sends the fax only at the fastest modem speed
that the receiving fax machine can accept.
The resolution at which the fax was sent might be very high.
To send the fax, lower the resolution and resend the fax.
The telephone line might be experiencing line noise.
Hang up and resend the fax. Have the telephone company
check the telephone line.
If the fax is being sent via a digital phone line, contact the
service provider.
150
The fax is being sent via an international call.
Allow more time to transmit fax jobs internationally.
The original document has a colored background.
Reprint the original document with a white background, and
then resend the fax.
Chapter 10 Fax (M1210 Series only)
ENWW
Problems receiving faxes
NOTE: Use the fax cord that came with the product in order to ensure that the product functions
correctly.
The product cannot receive faxes from an extension telephone.
Cause
Solution
The extension-telephone setting might be disabled.
Change the extension-telephone setting.
The fax cord might not be securely connected.
Verify that the fax cord is securely connected between the
telephone jack and the product (or another device that is
connected to the product). Press 1-2-3 in sequence, wait for
three seconds, and then hang up.
The product dialing mode might be incorrectly set, or the
extension phone might be incorrectly set.
Verify that the product dialing mode is set to Tone. Verify that
the extension phone is set up for tone dialing as well.
The product is not answering incoming fax calls.
ENWW
Cause
Solution
The answer mode might be set to Manual.
If the answer mode is set to Manual, the product does not
answer calls. Start the fax-receiving process manually.
The rings-to-answer setting might not be set correctly.
Check the rings-to-answer setting to verify that it is set
properly.
The answer-ring pattern feature might be turned on, but you
do not have the service, or you do have the service and the
feature is not set correctly.
Check the answer-ring pattern feature to verify that it is set
properly.
The fax cord might not be correctly connected, or the fax cord
is not working.
See the getting started guide to check the installation. Verify
that you are using the fax cord that came with the product.
The product might not be able to detect incoming fax tones
because the answering machine is playing a voice message.
Re-record the answering machine message, leaving at least
two seconds of silence at the beginning of the message.
Too many devices might be connected to the telephone line.
Do not attach more than three devices to the line. Remove the
last device that was connected and determine whether the
product works. If not, continue removing devices one at a time
and retry after removing each one.
The telephone line might not be working.
Do one of the following:
●
Increase the volume on the product, and then press the
Send Fax
button on the control panel. If a dial tone
exists, the telephone line is working.
●
Disconnect the product from the telephone jack, and then
connect a telephone. Try to make a telephone call to
verify that the telephone line is working.
Solve fax problems
151
The product is not answering incoming fax calls.
Cause
Solution
A voice-messaging service might be interfering with the
product as it attempts to answer calls.
Do one of the following:
The product might be out of paper and the memory is full.
●
Disable the messaging service.
●
Get a telephone line that is dedicated to fax calls.
●
Set the product answer mode to Manual. In manual
mode, you must start the fax-receive process yourself.
●
Leave the product set to automatic mode and lower the
rings-to-answer setting for the product to a number less
than the rings-to-answer setting for the voice mail. The
product will answer all incoming calls.
Refill the media input tray. Press the OK button. The product
prints all of the faxes it has saved in memory and then
resumes answering fax calls.
Faxes are not printing.
Cause
Solution
The media input tray is empty.
Load media. Any faxes that are received while the input tray
is empty are stored in memory and will print after the tray has
been refilled.
The receive-to-PC option might be selected, and faxes are
being received by the computer.
Check to determine whether the computer is receiving faxes.
The product has encountered an error.
Check the control panel for an error message.
Faxes are printing on two pages instead of one.
Cause
Solution
The autoreduction setting might not be set correctly.
Turn on the autoreduction setting.
The incoming faxes might have been sent on larger media.
Adjust the autoreduction setting to allow larger pages to be
printed on one page.
Received faxes are too light, are blank, or have poor print quality.
152
Cause
Solution
The product ran out of toner while printing a fax.
The product stores the most recently printed faxes. (The
amount of memory that is available determines the actual
number of faxes stored for reprinting.) As soon as possible,
replace the print cartridge, and then reprint the fax.
The fax that was sent was too light.
Contact the sender and have the sender resend the fax after
altering the contrast settings.
Chapter 10 Fax (M1210 Series only)
ENWW
Faxes are being received very slowly.
ENWW
Cause
Solution
The fax might be very complex, such as one with many
graphics.
Complex faxes take longer to be received. Breaking longer
faxes into multiple jobs and decreasing the resolution can
increase the transmission speed.
The resolution at which the fax was sent or is being received
might be very high.
To receive the fax, call and ask the sender to lower the
resolution and resend the fax.
The fax is being sent via an international call.
Allow more time to transmit fax jobs internationally.
Solve fax problems
153
Regulatory information and warranties
For regulatory and warranty information, see Additional statements for telecom (fax) products
on page 258.
154
Chapter 10 Fax (M1210 Series only)
ENWW
11 Manage and maintain the product
ENWW
●
Print information pages
●
Use the HP Toolbox software
●
Use the HP Embedded Web Server (M1210 Series only)
●
Product security features
●
Economy settings
●
Manage supplies and accessories
●
Clean the product
●
Product updates
155
Print information pages
Information pages reside within the product memory. These pages help diagnose and solve problems
with the product.
NOTE: M1210 Series: If the product language was not correctly set during installation, you can set
the language manually so the information pages print in one of the supported languages. Change the
language by using the System setup menu on the control panel.
Page description
How to print the page
Configuration page
Both models
Shows the current settings and product properties.
1.
Open the printer driver, and then click the Properties
or Preferences button.
2.
Click the Services tab, and then, in the Print
Information Pages drop-down list, click the Config
Page list item.
3.
Click the Print button.
M1130 Series
At the control panel, press and hold the Cancel
the Ready
button until
light starts blinking, and then release the button.
M1210 Series
156
Chapter 11 Manage and maintain the product
1.
On the product control panel, press the Setup
2.
Use the arrow buttons to select the Reports menu, and
then press the OK button.
3.
Use the arrow buttons to select the Config report
option, and then press the OK button.
button.
ENWW
Page description
How to print the page
Supplies Status page
Both models
Shows the status of the print cartridge, information about the
number of pages and jobs printed with the print cartridge,
and information about ordering a new print cartridge.
1.
Open the printer driver, and then click the Properties
or Preferences button.
2.
Click the Services tab, and then, in the Print
Information Pages drop-down list, click the
Supplies Status Page list item.
3.
Click the Print button.
M1130 Series
At the control panel, press and hold the Cancel
button until
the Ready
light starts blinking, and then release the button.
The supplies status page prints after the configuration page
prints.
M1210 Series
1.
On the product control panel, press the Setup
2.
Use the arrow buttons to select the Reports menu, and
then press the OK button.
3.
Use the arrow buttons to select the Supplies Status
option, and then press the OK button.
button.
Demo page
Both models
Contains examples of text and graphics.
1.
Open the printer driver, and then click the Properties
or Preferences button.
2.
Click the Services tab, and then, in the Print
Information Pages drop-down list, click the Demo
Page list item.
3.
Click the Print button.
M1210 Series
ENWW
1.
On the product control panel, press the Setup
2.
Use the arrow buttons to select the Reports menu, and
then press the OK button.
3.
Use the arrow buttons to select the Demo page option,
and then press the OK button.
button.
Print information pages
157
Page description
How to print the page
Menu map (M1210 Series only)
1.
On the product control panel, press the Setup
Shows the control-panel menus and available settings.
2.
Use the arrow buttons to select the Reports menu, and
then press the OK button.
3.
Use the arrow buttons to select the Menu structure
option, and then press the OK button.
1.
On the product control panel, press the Setup
2.
Use the arrow buttons to select the Reports menu, and
then press the OK button.
3.
Use the arrow buttons to select the Fax Reports option,
and then press the OK button.
Fax reports (M1210 Series only)
158
Chapter 11 Manage and maintain the product
button.
button.
ENWW
Use the HP Toolbox software
Perform a full software installation in order to use the HP Toolbox.
HP Toolbox is a software program that you can use for the following tasks:
●
Check the product status.
●
Configure the product settings.
●
Configure pop-up-alert messages.
●
View troubleshooting information.
●
View online documentation.
View HP Toolbox software
Open HP Toolbox in one of these ways:
M1130 Series
M1210 Series
1.
Open the printer driver, and then click the Properties or Preferences button.
2.
Click the Services tab.
●
In the Windows system tray, double-click the product icon
●
On the Windows Start menu, click Programs (or All Programs in Windows XP),
click HP, click HP LaserJet Professional M1130/M1210 MFP Series, and then
click HP Toolbox.
.
The HP Toolbox software contains the following sections for each product in the Devices window:
●
Status
●
Fax (M1210 Series only)
In addition to these sections, every page contains the following common elements:
ENWW
●
Shop for Supplies.
●
Other links.
Use the HP Toolbox software
159
Status
The Status folder contains links to the following main pages:
●
Device Status. View product status information. This page indicates product conditions such as
a jam or an empty tray. After you correct a product problem, click Refresh status to update the
product status.
Fax (M1210 Series only)
Use the HP Toolbox Fax tab to perform fax tasks from your computer. The Fax tab contains links to the
following main pages:
●
Fax Tasks. Perform such tasks as sending a fax or clearing the fax memory, or set the fax
receive mode.
●
Fax Phone Book. Add, edit, or delete entries in the all-in-one phone book.
●
Fax Send Log. View all of the recent faxes that have been sent from the all-in-one.
●
Fax Receive Log. View all of the recent faxes that have been received by the all-in-one.
●
Fax Data Properties. Manage the space used to store faxes on a computer. These settings
apply only if you have chosen to send or receive faxes remotely from a computer.
Fax tasks
The following three options are available when receiving a fax:
●
Print the fax. You can also select an option to have a message appear on your computer to
notifying you when the fax was printed.
●
Receive the fax on your computer. You can also select an option to have a message appear on
your computer to notifying you when the fax arrives. If the fax machine is connected to multiple
computers, only one computer can be designated to receive faxes.
●
Forward the fax to another fax machine.
NOTE: You must click Apply before the changes take effect.
Fax phone book
Use the HP Toolbox Fax phone book to add and remove entries or import phone books from a variety
of sources.
160
●
To add a new entry, click New. Type the contact name in the Contact name window. Type the
fax number in the Fax number window. Click Add/Edit.
●
To edit an existing entry, click anywhere on the row containing the contact name to select it, type
changes in the appropriate windows, and then click Add/Edit. Make sure that you do not have a
check mark in the Select column.
●
To delete an entry, select the item and then click Delete.
Chapter 11 Manage and maintain the product
ENWW
●
To move entries, you can select the entry and then click Move, or you can select Move and then
specify the entry in the dialog box. Either select Next empty row or specify the number of the
row where you want to move the entry.
NOTE: If you specify a row that is occupied, the new entry will overwrite the existing entry.
●
To import contacts from a phone book that exists in Lotus Notes, Outlook, or Outlook Express,
click Import Phone Book. Select the appropriate software program, navigate to the
appropriate file, and then click OK. You can also select individual entries from the phone book
instead of importing the entire phone book.
●
To select all of the entries in your phone book, click the Select column heading.
In addition to numerical digits, the following are valid characters for fax numbers:
●
(
●
)
●
+
●
-
●
*
●
#
●
R
●
W
●
.
●
,
●
<space>
NOTE: You must click Apply before the changes take effect.
ENWW
Use the HP Toolbox software
161
Fax send log
The HP Toolbox Fax send log lists all recently sent faxes and information about them, including the date
and time sent, job number, fax number, page count, and the results.
When you send a fax from a computer that is connected to the product, the fax contains a View link.
Clicking this link opens a new page that provides information about the fax.
Click any column heading in the Fax send log to re-sort the information in that column in ascending or
descending order.
The Results column provides the status of the fax. If the fax attempt was unsuccessful, this column
provides a description of why the fax was not sent.
NOTE: You must click Apply before the changes take effect.
Fax receive log
The HP Toolbox Fax receive log provides a list of all recently received faxes and information about
them including the date and time received, job number, fax number, page count, results, and an
abbreviated fax image.
When you receive a fax on a computer that is connected to the all-in-one, the fax contains a View link.
Clicking this link opens a new page that provides information about the fax.
Click on any column heading in the Fax receive log to re-sort the information in that column in
ascending or descending order.
The Results column provides the status of the fax. If the fax attempt was unsuccessful, this column
provides a description of why the fax was not received.
NOTE: You must click Apply before the changes take effect.
162
Chapter 11 Manage and maintain the product
ENWW
Shop for Supplies
This button, at the top of each page, links to a Web site where you can order replacement supplies.
You must have Internet access to use this feature.
Other Links
This section contains links that connect you to the Internet. You must have Internet access in order to use
any of these links. If you use a dial-up connection and did not connect when you first opened the
HP Toolbox, you must connect before you can visit these Web sites. Connecting might require that you
close the HP Toolbox and reopen it.
ENWW
●
HP Instant Support. Connects to the HP Instant Support Web site.
●
Product Support. Connects to the support site for the product where you can search for help
with a specific problem.
●
Shop for Supplies. Order supplies at the HP Web site.
●
Product Registration. Connects to the HP product registration Web site.
Use the HP Toolbox software
163
Use the HP Embedded Web Server (M1210 Series
only)
Use the HP Embedded Web Server (EWS) to view product and network status and to manage printing
functions from a computer.
●
View product status information
●
Determine the remaining life on all supplies and order new ones
●
View and change the product default configuration settings
●
View and change network configuration
You do not need to install any software on the computer. You only need to use one of these supported
Web browsers:
●
Internet Explorer 6.0 (and later)
●
Firefox 1.0 (and later)
●
Mozilla 1.6 (and later)
●
Opera 7.0 (and later)
●
Safari 1.2 (and later)
●
Konqueror 3.2 (and later)
The HP Embedded Web Server works when the product is connected to a TCP/IP-based network. The
HP Embedded Web Server does not support IPX-based connections or direct USB connections.
NOTE: You do not have to have Internet access to open and use the HP Embedded Web Server.
However, if you click a link on any of the pages, you must have Internet access to go to the site
associated with the link.
Open the HP Embedded Web Server
To open the HP Embedded Web Server, type the IP address or host name of the product in the address
field of a supported Web browser. To find the IP address or host name, print a configuration page.
NOTE: If an error occurs while opening the HP Embedded Web Server, confirm that the proxy
settings are correct for your network.
TIP:
164
After you open the URL, bookmark it so that you can return to it quickly in the future.
Chapter 11 Manage and maintain the product
ENWW
Features
Information tab
The Information pages group consists of the following pages:
●
Device Status displays the status of the product and HP supplies.
●
Device Configuration shows the information found on the Configuration page.
●
Supplies Status shows the status of HP supplies and provides part numbers. To order new
supplies, click Order Supplies in the upper-right part of the window.
●
Network Summary shows the information found on the Network Summary page.
Settings tab
Use this tab to configure the product from your computer. If this product is networked, always consult
with the product administrator before changing settings on this tab.
The Settings tab contains the Printing page where you can view and change the default print job
settings.
Networking tab
Network administrators can use this tab to control network-related settings for the product when it is
connected to an IP-based network.
HP Smart Install tab
NOTE: This tab is supported for Windows only.
Use this tab to install the product driver and software on a computer. Click the Download button to
start the installation process, and then follow the onscreen instructions to finish the process.
Links
Links are located in the upper-right part of the status pages. You must have Internet access to use any of
these links. If you use a dial-up connection and did not connect when you first opened the
HP Embedded Web Server, you must connect before you can visit these Web sites. Connecting might
require that you close the HP Embedded Web Server and reopen it.
ENWW
●
Shop for Supplies. Click this link to connect to the Sure Supply Web site and order genuine
HP supplies from HP or a reseller of your choice.
●
Support. Connects to the product support site. You can search for help regarding general topics.
Use the HP Embedded Web Server (M1210 Series only)
165
Product security features
Lock the formatter
1.
166
The formatter area, on the back of the product,
has a slot that you can use to attach a security
cable. Locking the formatter prevents someone
from removing valuable components from it.
Chapter 11 Manage and maintain the product
ENWW
Economy settings
Print with EconoMode
This product has an EconoMode option for printing drafts of documents. Using EconoMode can use less
toner and decrease the cost per page. However, using EconoMode can also reduce print quality.
HP does not recommend the full-time use of EconoMode. If EconoMode is used full-time, the toner
supply might outlast the mechanical parts in the print cartridge. If print quality begins to degrade under
these circumstances, you must install a new print cartridge, even if there is toner supply remaining in
the cartridge.
1.
On the File menu in the software program, click Print.
2.
Select the product, and then click the Properties or Preferences button.
3.
Click the Paper/Quality tab.
4.
Click the EconoMode check box.
Auto-Off mode
Auto-Off is an energy-saving feature of this product. After a user-specified time period, the product
automatically reduces its power consumption (Auto-Off). The product returns to the ready state when a
button is pressed or a print job is received.
Change the Auto-Off delay time
You can change how long the product remains idle (Auto-Off delay) before it enters Auto-Off mode.
NOTE: The default Auto-Off delay setting is 15 minutes.
1.
Use the printer driver to change the default settings. Follow the appropriate procedure, depending
on the operating system you are using.
Windows XP, Windows Server 2003, and Windows Server 2008 (using the
default Start menu view)
a.
Click Start, and then click Printers and Faxes.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Windows XP, Windows Server 2003, and Windows Server 2008 (using the
Classic Start menu view)
ENWW
a.
Click Start, click Settings, and then click Printers.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Economy settings
167
Windows Vista
a.
Click Start, click Control Panel, and then in the category for Hardware and Sound
click Printer.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Mac OS X 10.4
a.
From the Apple menu
Fax icon.
b.
Click the Printer Setup button.
, click the System Preferences menu and then click the Print &
Mac OS X 10.5 and 10.6
2.
a.
From the Apple menu
Fax icon.
b.
Select the product in the left side of the window.
c.
Click the Options & Supplies button.
d.
Click the Driver tab.
, click the System Preferences menu and then click the Print &
Select the Auto-Off delay from the Auto-Off drop-down list.
NOTE: The changed setting does not go into effect until a print job is sent to product.
168
Chapter 11 Manage and maintain the product
ENWW
Manage supplies and accessories
Correctly using, storing, and monitoring the print cartridge can help ensure high-quality print output.
Print when a cartridge reaches estimated end of life
When a print cartridge reaches the end of its estimated useful life, the product turns on the toner
light on the control panel. You do not need to replace the supply at this time unless print quality is no
longer acceptable. When the supply has reached this condition, the HP Premium Protection warranty
for that supply has ended.
Manage print cartridges
Print-cartridge storage
Do not remove the print cartridge from its package until you are ready to use it.
CAUTION: To prevent damage to the print cartridge, do not expose it to light for more than a few
minutes.
HP policy on non-HP print cartridges
Hewlett-Packard Company cannot recommend the use of non-HP print cartridges, either new or
remanufactured.
NOTE: Any damage caused by a non-HP print cartridge is not covered under the HP warranty and
service agreements.
HP fraud hotline and Web site
Call the HP fraud hotline (1-877-219-3183, toll-free in North America) or go to www.hp.com/go/
anticounterfeit when you install an HP print cartridge and the control-panel message says the cartridge
is non-HP. HP will help determine if the cartridge is genuine and take steps to resolve the problem.
Your print cartridge might not be a genuine HP print cartridge if you notice the following:
●
You are experiencing a high number of problems with the print cartridge.
●
The cartridge does not look like it usually does (for example, the orange pull tab is missing, or the
packaging differs from HP packaging).
Recycle supplies
To recycle a genuine HP print cartridge, place the used cartridge in the box in which the new cartridge
arrived. Use the enclosed return label to send the used supply to HP for recycling. For complete
information, see the recycling guide that is included with each new HP supply item.
ENWW
Manage supplies and accessories
169
Replacement instructions
Redistribute toner
When a small amount of toner remains in print cartridge, faded or light areas might appear on the
printed page. You might be able to temporarily improve print quality by redistributing the toner.
170
1.
Lift the scanner assembly, and open the print-cartridge door.
2.
Remove the print cartridge.
Chapter 11 Manage and maintain the product
ENWW
3.
To redistribute the toner, gently rock the print cartridge from front to back.
CAUTION: If toner gets on your clothing, wipe it off with a dry cloth and wash the clothing in
cold water. Hot water sets toner into the fabric.
ENWW
4.
Install the print cartridge.
5.
Close the print-cartridge door and the scanner assembly.
Manage supplies and accessories
171
If the print is still light, install a new print cartridge.
Replace the print cartridge
When a print cartridge approaches the end of useful life, you can continue printing with the current
cartridge until redistributing the toner no longer yields acceptable print quality.
1.
Lift the scanner assembly, and open the printcartridge door.
2.
Remove the old print cartridge.
172
Chapter 11 Manage and maintain the product
ENWW
3.
Remove the new print cartridge from the
packaging. Place the used print cartridge in
the bag and box for recycling.
CAUTION: To prevent damage to the print
cartridge, hold the print cartridge at each end.
Do not touch the cartridge shutter or the roller
surface.
4.
Grasp both sides of the print cartridge and
gently rock the print cartridge to distribute the
toner evenly inside the cartridge.
5.
Bend the tab on the left side of the cartridge
until the tab breaks loose, and then pull the tab
until all the tape is removed from the cartridge.
Place the tab and tape in the print-cartridge
box to return for recycling.
ENWW
Manage supplies and accessories
173
6.
Install the print cartridge.
7.
Close the print-cartridge door and the scanner
assembly.
CAUTION: If toner gets on your clothing,
wipe it off with a dry cloth and wash the
clothing in cold water. Hot water sets toner
into the fabric.
174
Chapter 11 Manage and maintain the product
ENWW
Replace the pickup roller
The pickup roller wears out with normal use. Using poor-quality paper can cause the pickup roller to
wear out more frequently. If the product regularly does not pick up a sheet of paper, you might need to
clean or replace the pickup roller.
1.
Lift the scanner assembly, and open the print-cartridge door.
2.
Remove the print cartridge.
CAUTION: To prevent damage to the print cartridge, minimize its exposure to direct light.
Cover the print cartridge with a sheet of paper.
ENWW
Manage supplies and accessories
175
176
3.
Find the pickup roller.
4.
Release the small, white tabs on each side of the pickup roller, and rotate the pickup roller toward
the front.
Chapter 11 Manage and maintain the product
ENWW
ENWW
5.
Gently pull the pickup roller up and out.
6.
Position the new pickup roller in the slot. The circular and rectangular slots on each side prevents
you from installing the roller incorrectly.
Manage supplies and accessories
177
178
7.
Rotate the top of the new pickup roller away from you until both sides snap into place.
8.
Install the print cartridge.
Chapter 11 Manage and maintain the product
ENWW
9.
ENWW
Close the print-cartridge door and the scanner assembly.
Manage supplies and accessories
179
Replace the separation pad
The separation pad wears out with normal use. Using poor-quality paper can cause the separation pad
to wear out more frequently. If the product regularly pulls multiple sheets of paper at a time, you might
need to clean or replace the separation pad.
NOTE: Before changing the separation pad, clean the pickup roller.
WARNING! Before changing the separation pad, turn the product off, disconnect the power cord
from the wall outlet, and then wait for the product to cool.
1.
Disconnect the power cord from the product.
2.
Remove the paper and close the input tray. Set the product on its side.
CAUTION:
3.
180
The scanner assembly opens when the product is on its side.
At the bottom of the product, unscrew the two screws holding the separation pad in place.
Chapter 11 Manage and maintain the product
ENWW
ENWW
4.
Remove the separation pad.
5.
Insert the new separation pad, and screw it into place.
6.
Place the product in the upright position, reconnect the power cord, and then turn on the product.
Manage supplies and accessories
181
Clean the product
Clean the pickup roller
If you want to clean the pickup roller before deciding to replace it, follow these instructions:
WARNING! Before cleaning the pickup roller, turn the product off, disconnect the power cord from
the wall outlet, and then wait for the product to cool.
1.
Lift the scanner assembly, and open the print-cartridge door.
2.
Remove the print cartridge.
CAUTION: To prevent damage to the print cartridge, minimize its exposure to direct light.
Cover the print cartridge with a sheet of paper.
182
Chapter 11 Manage and maintain the product
ENWW
ENWW
3.
Find the pickup roller.
4.
Release the small, white tabs on each side of the pickup roller, and rotate the pickup roller toward
the front.
Clean the product
183
5.
Gently pull the pickup roller up and out.
6.
Dab a lint-free cloth in isopropyl alcohol, and scrub the roller.
WARNING! Alcohol is flammable. Keep the alcohol and cloth away from an open flame.
Before you close the product and plug in the power cord, allow the alcohol to dry completely.
NOTE: In certain areas of California, air pollution control regulations restrict the use of liquid
Isopropyl Alcohol (IPA) as a cleaning agent. In those areas of California, please disregard the
previous recommendations and use a dry, lint-free cloth, moistened with water, to clean the pickup
roller.
7.
184
Using a dry, lint-free cloth, wipe the pickup roller to remove loosened dirt.
Chapter 11 Manage and maintain the product
ENWW
ENWW
8.
Allow the pickup roller to dry completely before you reinstall it in the product.
9.
Reconnect the power cord.
Clean the product
185
Clean the separation pad
The separation pad wears out with normal use. Using poor-quality paper can cause the separation pad
to wear out more frequently. If the product regularly pulls multiple sheets of paper at a time, you might
need to clean or replace the separation pad.
WARNING! Before cleaning the separation pad, turn the product off, disconnect the power cord
from the wall outlet, and then wait for the product to cool.
1.
Disconnect the power cord from the product.
2.
Remove the paper and close the input tray. Set the product on its side.
CAUTION:
3.
186
The scanner assembly opens when the product is on its side.
At the bottom of the product, unscrew the two screws holding the separation pad in place.
Chapter 11 Manage and maintain the product
ENWW
4.
Remove the separation pad.
5.
Dab a lint-free cloth in isopropyl alcohol, and scrub the separation pad. Use a dry, lint-free cloth
to remove the loosened dirt, and wait for the separation pad to dry.
WARNING! Alcohol is flammable. Keep the alcohol and cloth away from an open flame.
Before you close the product and plug in the power cord, allow the alcohol to dry completely.
NOTE: In certain areas of California, air pollution control regulations restrict the use of liquid
Isopropyl Alcohol (IPA) as a cleaning agent. In those areas of California, please disregard the
previous recommendations and use a dry, lint-free cloth, moistened with water, to clean the pickup
roller.
ENWW
Clean the product
187
188
6.
Insert the cleaned separation pad, and screw it into place.
7.
Place the product in the upright position, reconnect the power cord, and then turn on the product.
Chapter 11 Manage and maintain the product
ENWW
Clean the paper path
If you are experiencing toner specks or dots on the printouts, clean the paper path. This process uses a
transparency to remove dust and toner from the paper path. Do not use bond or rough paper.
NOTE: For best results use a sheet of transparency. If you do not have any transparencies, you can
use copier-grade media (60 to 163 g/m2 (16 to 43 lb)) that has a smooth surface.
1.
Make sure that the product is idle and the Ready
2.
Load media in the input tray.
3.
Use the printer driver to process the cleaning page. Follow the appropriate procedure, depending
on the operating system you are using.
light is on.
Windows XP, Windows Server 2003, and Windows Server 2008 (using the
default Start menu view)
a.
Click Start, and then click Printers and Faxes.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Windows XP, Windows Server 2003, and Windows Server 2008 (using the
Classic Start menu view)
a.
Click Start, click Settings, and then click Printers.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Windows Vista
ENWW
a.
Click Start, click Control Panel, and then in the category for Hardware and Sound
click Printer.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Clean the product
189
Mac OS X 10.4
a.
From the Apple menu
Fax icon.
b.
Click the Printer Setup button.
, click the System Preferences menu and then click the Print &
Mac OS X 10.5 and 10.6
4.
a.
From the Apple menu
Fax icon.
b.
Select the product in the left side of the window.
c.
Click the Options & Supplies button.
d.
Click the Driver tab.
, click the System Preferences menu and then click the Print &
In the Cleaning Page area, click the Start button to process the cleaning page.
NOTE: The cleaning process takes about 2 minutes. The cleaning page stops periodically during the
cleaning process. Do not turn the product off until the cleaning process has finished. You might need to
repeat the cleaning process several times to thoroughly clean the product.
190
Chapter 11 Manage and maintain the product
ENWW
Clean the print-cartridge area
You do not need to clean the print-cartridge area often. However, cleaning this area can improve the
quality of the printed sheets.
ENWW
1.
Disconnect the power cord from the product.
2.
Lift the scanner assembly, and open the print-cartridge door.
Clean the product
191
3.
Remove the print cartridge.
CAUTION: Do not touch the black-sponge transfer roller inside the product. Doing so can
damage the product.
CAUTION:
of paper.
4.
192
To prevent damage, do not expose the print cartridge to light. Cover it with a piece
With a dry, lint-free cloth, wipe any residue from the paper-path area and the print-cartridge
cavity.
Chapter 11 Manage and maintain the product
ENWW
ENWW
5.
Install the print cartridge.
6.
Close the print-cartridge door and the scanner assembly.
Clean the product
193
7.
Reconnect the power cord.
8.
Print a few pages to clean any toner residue from the product.
Clean the exterior
Use a soft, damp, lint-free cloth to wipe dust, smudges, and stains off of the exterior of the device.
Clean the scanner glass strip and platen
Over time, specks of debris might collect on the scanner glass and white plastic backing, which can
affect performance. Use the following procedure to clean the scanner glass and white plastic backing.
194
1.
Use the power switch to turn off the product, and then unplug the power cord from the electrical
socket.
2.
Open the scanner lid.
Chapter 11 Manage and maintain the product
ENWW
3.
Clean the scanner glass and the white plastic backing with a soft cloth or sponge that has been
moistened with nonabrasive glass cleaner.
CAUTION: Do not use abrasives, acetone, benzene, ammonia, ethyl alcohol, or carbon
tetrachloride on any part of the product; these can damage the product. Do not place liquids
directly on the glass or platen. They might seep and damage the product.
ENWW
4.
Dry the glass and white plastic backing with a chamois or a cellulose sponge to prevent spotting.
5.
Plug in the product, and then use the power switch to turn on the product.
Clean the product
195
Product updates
Software and firmware updates and installation instructions for this product are available at
www.hp.com/support/ljm1130series or www.hp.com/support/ljm1210series. Click Downloads
and drivers, click the operating system, and then select the download for the product.
196
Chapter 11 Manage and maintain the product
ENWW
12 Solve problems
ENWW
●
Solve general problems
●
Restore the factory-set defaults (M1210 Series only)
●
Interpret control-panel light patterns (M1130 Series only)
●
Interpret control-panel messages (M1210 Series only)
●
Clear jams
●
Solve paper-handling problems
●
Solve image-quality problems
●
Solve performance problems
●
Solve connectivity problems
●
Solve software problems
197
Solve general problems
If the product is not responding correctly, complete the steps in the following checklist, in order. If the
product does not pass a step, follow the corresponding troubleshooting suggestions. If a step resolves
the problem, you can stop without performing the other steps on the checklist.
Troubleshooting checklist
1.
2.
Make sure that the product is set up correctly.
a.
Press the power button to turn on the product or to deactivate the Auto-Off mode.
b.
Check the power-cable connections.
c.
Make sure that the line voltage is correct for the product power configuration. (See the label
that is on the back of the product for voltage requirements.) If you are using a power strip
and its voltage is not within specifications, plug the product directly into the wall. If it is
already plugged into the wall, try a different outlet.
d.
If none of these measures restores power, contact HP Customer Care.
Check the cabling.
a.
Check the cable connection between the product and the computer. Make sure that the
connection is secure.
b.
Make sure that the cable itself is not faulty by using a different cable, if possible.
c.
Check the network connection (M1210 Series only): Make sure the network light is lit. The
network light is next to the network port on the back of the product.
If the product remains unable to connect to the network, uninstall and then reinstall the
product. If the error persists, contact a network administrator.
3.
M1130 Series: Check to see if any control-panel lights are lit.
M1210 Series: Check to see if any messages appear on the control panel.
198
4.
Make sure that the paper that you are using meets specifications.
5.
Make sure that the paper is loaded correctly in the input tray.
6.
Make sure that the product software is installed correctly.
7.
Verify that you have installed the printer driver for this product, and that you are selecting this
product from the list of available printers.
8.
Print a configuration page.
a.
If the page does not print, verify that the input tray contains paper.
b.
Make sure that the print cartridge is installed correctly.
Chapter 12 Solve problems
ENWW
9.
c.
If the page jams in the product, clear the jam.
d.
If the print quality is unacceptable, complete the following steps:
●
Verify that the print settings are correct for the media that you are using.
●
Solve print-quality problems.
Print a small document from a different program that has worked in the past. If this solution works,
then the problem is with the program you are using. If this solution does not work (the document
does not print), complete these steps:
a.
Try printing the job from another computer that has the product software installed.
b.
Check the cable connection. Direct the product to the correct port, or reinstall the software,
selecting the connection type that you are using.
Factors that affect product performance
Several factors affect the time it takes to print a job:
●
The use of special paper (such as transparencies, heavy paper, and custom-size paper)
●
Product processing and download time
●
The complexity and size of graphics
●
The speed of the computer you are using
●
The USB or network connection
●
The product I/O configuration
Restore the factory-set defaults (M1210 Series only)
Restoring the factory-set defaults returns all of the settings to the factory defaults, and it also clears the
fax header name, phone number, and any stored faxes in the product memory.
CAUTION: Restoring the factory-set defaults returns all of the settings to the factory defaults, and it
also clears the fax header name, phone number, and any stored faxes in the product memory. This
procedure also clears the fax phone book, and deletes any pages that are stored in the memory. The
procedure then automatically restarts the product.
1.
On the product control panel, press the Setup
2.
Use the arrows buttons to select the Service menu, and then press the OK button.
3.
Use the arrows buttons to select the Restore Defaults option, and then press the OK button.
button.
The product automatically restarts.
ENWW
Restore the factory-set defaults (M1210 Series only)
199
Interpret control-panel light patterns (M1130 Series
only)
If the product requires attention, an error code appears on the control-panel display.
Table 12-1 Status-light legend
Symbol for "light off"
Symbol for "light on"
Symbol for "light blinking"
Table 12-2 Control-panel light patterns
Light status
State of the product
Action
All lights are off.
The product is turned off.
Press the power button to turn on the
product.
Ready and attention lights blink.
The status lights cycle during the
formatter initialization period or when
the product is processing a cleaning
page.
No action is required. Wait for the
initialization period to end. The
product should enter the ready state
when the initialization period is
finished.
Ready light is on.
The product is in the ready state.
No action is required. The product is
ready to receive a print job.
Ready light is blinking.
The product is receiving or processing
data.
No action is required. The product is
receiving or processing a print job.
200
Error code
Chapter 12 Solve problems
ENWW
Table 12-2 Control-panel light patterns (continued)
Light status
Error code
State of the product
Action
The product is in low power mode.
No action is required.
E0
Paper is jammed in the product.
Clear the jam.
E1
The input tray is empty.
Load the tray.
E2
A door is open
Verify that the print-cartridge door is
fully closed.
E4
The product memory is full
The job is too complex for the product
to print. Simplify the job, or divide it
into multiple files.
E5
The product did not pick up paper
from the tray.
You might need to clean or replace
the pickup roller.
H0
The product is in manual-feed mode.
Load the correct paper type and size
into the input tray.
H1
The product is processing a manual
duplex job.
Load the pages into the input tray to
print the second sides.
E3
The print cartridge is missing or is not
installed correctly.
Install the print cartridge.
The print cartridge has reached the
end of its estimated useful life. When
the supply has reached this condition,
the HP Premium Protection warranty for
that supply has ended.
You do not need to replace the print
cartridge at this time unless print
quality is no longer acceptable.
Ready light is blinking slowly.
Attention light is blinking.
The attention and toner lights are
blinking.
The toner light is on.
ENWW
Interpret control-panel light patterns (M1130 Series only)
201
Table 12-2 Control-panel light patterns (continued)
Light status
Error code
Attention light is blinking, and ready
light is on.
State of the product
Action
The product has experienced a
continual error from which it will
recover on its own.
If the recovery is successful, the
product continues to the processing
data state and completes the job.
If the recovery is unsuccessful, the
product continues to the continuable
error state. Try removing any media
from the media path and turning the
product power off, and then on again.
The attention and ready lights are
on.
E6
E7
E8
The product has experienced a fatal
error from which it cannot recover.
1.
Turn off the product or disconnect
the power cord from the product.
2.
Wait 30 seconds, and then turn
on the product or reconnect the
power cord to the product.
3.
Wait for the product to initialize.
E9
If the error persists, contact
HP customer support.
202
Chapter 12 Solve problems
ENWW
Interpret control-panel messages (M1210 Series
only)
Control-panel message types
Alert and warning messages appear temporarily and might require you to acknowledge the message
by pressing the OK button to resume or by pressing the Cancel
button to cancel the job. With
certain warnings, the job might not complete or the print quality might be affected. If the alert or
warning message is related to printing and the auto-continue feature is on, the product will attempt to
resume the printing job after the warning has appeared for 10 seconds without acknowledgement.
Critical error messages can indicate some kind of failure. Turning off and then turning on the power
might fix the problem. If a critical error persists, the product might require service.
Control-panel messages
Control panel message
Description
Recommended action
50.X Fuser Error
The product has experienced an internal
hardware error.
1.
Turn off the power by using the power
switch, and then wait at least 30
seconds.
2.
If a surge protector is being used,
remove it. Plug the product directly into
the wall socket.
3.
Turn on the power and wait for the
product to initialize.
Turn off then on
If the error persists, contact HP. See
www.hp.com/support/ljm1210series or the
support flyer that came in the product box.
52 Scanner Error
Turn off then on
The product has experienced a scanner
error.
Turn off the power by using the power
switch, wait at least 30 seconds, and then
turn on the power and wait for the product to
initialize.
If a surge protector is being used, remove it.
Plug the product directly into the wall socket.
Use the power switch to turn the product on.
If the error persists, contact HP. See
www.hp.com/support/ljm1210series or the
support flyer that came in the product box.
ENWW
Interpret control-panel messages (M1210 Series only)
203
Control panel message
Description
Recommended action
54.1C Error
The product has experienced an internal
hardware error.
Turn off the power by using the power
switch, wait at least 30 seconds, and then
turn on the power and wait for the product to
initialize.
Turn off then on
If a surge protector is being used, remove it.
Plug the product directly into the wall socket.
Use the power switch to turn the product on.
If the error persists, contact HP. See
www.hp.com/support/ljm1210series or the
support flyer that came in the product box.
Comm. error
The product experienced a communication
error while attempting to send or receive a
fax.
Verify that the fax phone line is working
correctly.
Try sending or receiving the fax again.
If the error persists, contact HP. See
www.hp.com/support/ljm1210series or the
support flyer that came in the product box.
Device error
The product experienced an internal
communication error.
This is a warning message only. Job output
might be affected.
Door open
The cover above the print cartridge is open.
Close the cover.
Engine comm. Error
The product has experienced an internal
hardware error.
1.
Turn off the power by using the power
switch, and then wait at least 30
seconds.
2.
If a surge protector is being used,
remove it. Plug the product directly into
the wall socket.
3.
Turn on the power and wait for the
product to initialize.
Press [OK]
If the error persists, contact HP. See
www.hp.com/support/ljm1210series or the
support flyer that came in the product box.
Fax recv. error
The product was unable to receive an
incoming fax.
Verify that the fax phone line is working
correctly.
Ask the person who sent the fax to send it
again.
If the error persists, contact HP. See
www.hp.com/support/ljm1210series or the
support flyer that came in the product box.
Fax Send error
The product was unable to send the fax.
Try sending the fax later, or confirm with the
recipient that the receiving fax machine is
ready.
If the error persists, contact HP. See
www.hp.com/support/ljm1210series or the
support flyer that came in the product box.
204
Chapter 12 Solve problems
ENWW
Control panel message
Description
Recommended action
Jam in <location>
The product has detected a jam in the
location indicated in the message.
Clear the jam from the area indicated in the
message, and then follow the control-panel
instructions. Clearing some jams requires you
to open the top cover and remove the print
cartridge.
The product is performing a cleaning cycle.
Load the tray with plain paper of the size
indicated. Press the OK button to start the
cleaning cycle.
Load tray <TYPE>, <SIZE>
The tray is empty.
Load the tray with the correct type and size
of paper.
Manual duplex
The product is processing a manual duplex
job.
To print the second side, place the pages
face down in the tray with the top edge first.
The product is set for the manual feed mode.
Load the tray with the correct size and type
of paper, or press the OK button to use the
paper that is in the tray.
The product does not have enough memory
to process the job.
If the product is processing other jobs, send
the job again after those jobs have finished.
alternates with
Open door and clear jam
Load tray 1 PLAIN <SIZE>
alternates with
Cleaning Mode
alternates with
Load tray1
Press [OK]
Manual feed <SIZE>, <TYPE>
alternates with
Press [OK] for available media
Memory is low
Press [OK]
If the problem continues, turn off the power
by using the power switch, and then wait at
least 30 seconds. Turn on the power and
wait for the product to initialize.
Misprint
Press [OK]
No paper pickup
Press [OK]
Page too complex
Press [OK]
The product has experienced an internal
hardware error.
Press the OK button to continue. Job output
might be affected.
The product has experienced an internal
hardware error.
Press the OK button to continue. Job output
might be affected.
The product could not print the current page
because of its complexity.
Press the OK button to clear the message.
Allow the product to finish the job, or press
the Cancel
button to cancel the job.
Printer jam clear paper path
The product has detected a jam in the input
tray.
Clear the jam from the area indicated in the
message, and then follow the control panel
instructions.
Settings cleared
The product has cleared job settings.
Re-enter any appropriate job settings.
ENWW
Interpret control-panel messages (M1210 Series only)
205
Clear jams
When clearing jams, be careful not to tear jammed paper. If a small piece of paper remains in the
product, it could cause additional jams.
Common causes of jams
●
The input tray is loaded incorrectly or is too full.
NOTE: When you add new media, always remove all of the media from the input tray and
straighten the entire stack. This helps prevent multiple feeds and reduces media jams.
●
The media does not meet HP specifications.
●
The product might need to be cleaned to remove paper dust and other particles from the paper
path.
Loose toner might remain in the product after a media jam. This toner clears up after a few sheets print.
CAUTION: If you get any toner on your clothes, wash them in cold water. Hot water will
permanently set the toner into the fabric.
206
Chapter 12 Solve problems
ENWW
Jam locations
Jams can occur at the following locations in the product.
1
2
3
4
1
Document feeder (M1210 Series only)
2
Output bin
3
Input tray
4
Internal areas (open the print-cartridge door)
NOTE: Jams can occur in more than one location.
ENWW
Clear jams
207
Clear jams from the document feeder (M1210 Series only)
1.
Open the document-feeder lid.
2.
Carefully remove jammed paper. Gently try to
remove the page without tearing it.
3.
Close the document feeder lid.
208
Chapter 12 Solve problems
ENWW
Clear jams from the output areas
CAUTION: Do not use sharp objects, such as tweezers or needle-nose pliers, to remove jams.
Damage caused by sharp objects will not be covered by the warranty.
1.
Lift the scanner assembly, and open the printcartridge door.
2.
Remove the print cartridge.
ENWW
Clear jams
209
3.
Keep the print cartridge door open, and then
with both hands, grasp the side of the jammed
media that is most visible (this includes the
middle), and carefully pull it free from the
product.
4.
Install the print cartridge.
5.
Close the print-cartridge door and the scanner
assembly.
210
Chapter 12 Solve problems
ENWW
Clear jams from the input tray
1.
Lift the scanner assembly, and open the printcartridge door.
2.
Remove the print cartridge.
3.
Remove the media stack from the input tray.
ENWW
Clear jams
211
4.
With both hands, grasp the side of the
jammed media that is most visible (this
includes the middle), and carefully pull it free
from the product.
5.
Install the print cartridge.
6.
Close the print-cartridge door and the scanner
assembly.
212
Chapter 12 Solve problems
ENWW
Clear jams from inside the product
1.
Lift the scanner assembly, and open the printcartridge door.
2.
Remove the print cartridge.
3.
If you can see the jammed paper, carefully
grasp the jammed paper, and slowly pull it out
of the product.
ENWW
Clear jams
213
4.
Reinstall the print cartridge.
5.
Close the print-cartridge door and the scanner
assembly.
Change the jam recovery setting
When the Jam Recovery feature is turned on, the product reprints any pages that are damaged during
a jam.
1.
Use the printer driver to change the default settings. Follow the appropriate procedure, depending
on the operating system you are using.
Windows XP, Windows Server 2003, and Windows Server 2008 (using the
default Start menu view)
214
a.
Click Start, and then click Printers and Faxes.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Chapter 12 Solve problems
ENWW
Windows XP, Windows Server 2003, and Windows Server 2008 (using the
Classic Start menu view)
a.
Click Start, click Settings, and then click Printers.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Windows Vista
a.
Click Start, click Control Panel, and then in the category for Hardware and Sound
click Printer.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Mac OS X 10.4
a.
From the Apple menu
Fax icon.
b.
Click the Printer Setup button.
, click the System Preferences menu and then click the Print &
Mac OS X 10.5 and 10.6
2.
ENWW
a.
From the Apple menu
Fax icon.
b.
Select the product in the left side of the window.
c.
Click the Options & Supplies button.
d.
Click the Driver tab.
, click the System Preferences menu and then click the Print &
Click the Auto option or the Off option under Jam Recovery.
Clear jams
215
Solve paper-handling problems
The following problems with media cause print-quality deviations, jamming, or damage to the product.
Problem
Cause
Solution
Poor print quality or toner adhesion
The paper is too moist, too rough, too
heavy or too smooth, is embossed, or
from a faulty paper lot.
Try another kind of paper, between 100
and 250 Sheffield, with 4% to 6%
moisture content.
Dropouts, jamming, or curl
The paper has been stored incorrectly.
Store paper flat in its moisture-proof
wrapping.
The paper has variability from one side
to the other.
Turn the paper over.
The paper is too moist, has the wrong
grain direction, or is of short-grain
construction
Use long-grain paper.
The paper varies from side-to-side.
Turn the paper over.
Jamming, damage to product
The paper has cutouts or perforations.
Use paper that is free of cutouts or
perforations.
Problems with feeding
The paper has ragged edges.
Use high-quality paper that is made for
laser printers.
The paper varies from side-to-side.
Turn the paper over.
The paper is too moist, too rough, too
heavy or too smooth, has the wrong
grain direction, is of short-grain
construction, or it is embossed, or from a
faulty paper lot.
Try another kind of paper, between 100
and 250 Sheffield, 4% to 6% moisture
content.
Print is skewed (crooked).
The media guides might be incorrectly
adjusted.
Remove all media from the input tray,
straighten the stack, and then load the
media in the input tray again. Adjust the
media guides to the width and length of
the media that you are using and try
printing again.
More than one sheet feeds at one time.
The media tray might be overloaded.
Remove some of the media from the
tray.
The media might be wrinkled, folded, or
damaged.
Verify that the media is not wrinkled,
folded, or damaged. Try printing on
media from a new or different package.
Excessive curl
216
Chapter 12 Solve problems
Use long-grain paper.
ENWW
ENWW
Problem
Cause
Solution
The product does not pull media from
the input tray.
The product might be in manual-feed
mode.
At the computer, follow the onscreen
instructions to deactivate manual-feed
mode. Or, at the product, open and
close the print-cartridge door.
The pickup roller might be dirty or
damaged.
Contact HP Customer Care. See
www.hp.com/support/ljm1130series or
www.hp.com/support/ljm1210series or
the support flyer that came in the box.
The paper-length adjustment control in
the input tray is set at a length that is
greater than the media size.
Set the paper-length adjustment control
to the correct length.
Solve paper-handling problems
217
Solve image-quality problems
Print-quality examples
General print-quality issues
The following examples depict letter-size paper that has passed through the product short-edge-first.
These examples illustrate problems that would affect all of the pages that you print. The topics that
follow list the typical cause and solution for each of these examples.
Problem
Cause
Solution
Print is light or faded.
The paper might not meet HP specifications.
Use paper that meets HP specifications.
The print cartridge might be defective or
low. If you use a non-HP print cartridge, no
messages appear on the product control
panel.
Replace the print cartridge.
If the whole page is light, the print density
adjustment is too light or EconoMode might
be turned on.
Adjust the print density, and disable
EconoMode in the printer driver.
The paper might not meet HP specifications.
Use paper that meets HP specifications.
The paper path might need cleaning.
Clean the paper path.
A single sheet of paper might be defective.
Try reprinting the job.
The moisture content of the paper is uneven
or the paper has moist spots on its surface.
Try different paper, such as high-quality
paper that is intended for laser printers.
Toner specks appear.
Dropouts appear.
If the print cartridge is not low or empty,
inspect the toner roller to see if the roller is
damaged. If it is, replace the print
cartridge.
The paper lot is flawed. The manufacturing
processes can cause some areas to reject
toner.
The print cartridge might be defective or
low.
218
Chapter 12 Solve problems
Replace the print cartridge.
If the error persists, contact HP. See
www.hp.com/support/ljm1130series or
www.hp.com/support/ljm1210series or
the support flyer that came in the product
box.
ENWW
Problem
Cause
Solution
Vertical streaks or bands appear
on the page.
The print cartridge might be defective.
Replace the print cartridge.
The paper might not meet HP specifications.
Use a different paper with a lighter basis
weight.
The print-density setting is too high.
Decrease the print-density setting. This
decreases the amount of background
shading.
Very dry (low humidity) conditions can
increase the amount of background shading.
Check the product environment.
The print cartridge might be defective or
low.
Replace the print cartridge.
The paper might not meet HP specifications.
Use paper that meets HP specifications.
If toner smears appear on the leading edge
of the paper, the media guides are dirty, or
debris has accumulated in the print path.
Clean the media guides and the paper
path.
The print cartridge might be defective.
Replace the print cartridge.
The fuser temperature might be too low.
In the printer driver, make sure the
appropriate paper type is selected.
The product is not set to print on the type of
paper on which you want to print.
In the printer driver, select the Paper/
Quality tab and set Paper Type to
match the type of paper on which you are
printing. Print speed might be slower if you
are using heavy paper.
The paper might not meet HP specifications.
Use paper that meets HP specifications.
The paper path might need cleaning.
Clean the paper path.
The power source might be defective.
Plug the product directly into an AC outlet
instead of into a power strip.
The fuser temperature might be too low.
In the printer driver, make sure the
appropriate paper type is selected.
Aa BbCc
Aa BbCc
Aa BbCc
Aa BbCc
Aa BbCc
The amount of background toner
shading becomes unacceptable.
Toner smears appear on the
media.
The toner smears easily when
touched.
ENWW
Solve image-quality problems
219
Problem
Cause
Solution
Marks repeatedly appear at even
intervals on the page.
The product is not set to print on the type of
paper on which you want to print.
In the printer driver, select the Paper/
Quality tab and set Paper Type to
match the type of paper on which you are
printing. Print speed might be slower if you
are using heavy paper.
Internal parts might have toner on them.
The problem typically corrects itself after a
few more pages.
The paper path might need cleaning.
Clean the paper path.
The print cartridge might be damaged.
If a repetitive mark occurs at the same spot
on the page, install a new HP print
cartridge.
The paper might not meet HP specifications.
Use a different paper, such as high-quality
paper that is intended for laser printers.
If characters are incorrectly formed so that
they produce a wavy effect, the laser
scanner might need service.
Verify that the problem also occurs on the
configuration page. If so, contact HP. See
www.hp.com/support/ljm1130series or
www.hp.com/support/ljm1210series or
the support flyer that came in the product
box.
The product is not set to print on the type of
paper on which you want to print.
In the printer driver, select the Paper/
Quality tab and set Paper Type to
match the type of paper on which you are
printing. Print speed might be slower if you
are using heavy paper.
The printed page contains
misformed characters.
The printed page is curled or
wavy.
If the problem persists, select a paper type
that uses a lower fuser temperature, such as
transparencies or light media.
The paper might have been in the input tray
too long.
Turn over the stack of paper in the tray.
Also, try rotating the paper 180° in the
input tray.
The paper might not meet HP specifications.
Use a different paper, such as high-quality
paper that is intended for laser printers.
Both high temperature and humidity can
cause paper curl.
Check the product environment.
The fuser temperature might be curling the
paper.
M1130 Series select a paper type that
uses a lower fuser temperature, such as
transparencies or light media.
M1210 SeriesAt the product control
panel, turn on the Less paper curl setting
in the Service menu.
220
Chapter 12 Solve problems
ENWW
Problem
Cause
Solution
Text or graphics are skewed on
the printed page.
The paper might be loaded incorrectly or the
input tray might be too full.
Verify that the paper is loaded correctly
and that the paper guides are not too tight
or too loose against the stack.
The paper might not meet HP specifications.
Use a different paper, such as high-quality
paper that is intended for laser printers.
The paper might be loaded incorrectly or the
input tray might be too full.
Turn over the stack of paper in the input
tray, or try rotating the paper 180° in the
input tray.
The printed page contains
wrinkles or creases.
Verify that the paper is loaded correctly
and that the paper guides are not too tight
or too loose against the stack.
ENWW
There might be a jam in the paper path.
Clear any jams in the product.
The paper might not meet HP specifications.
Use a different paper, such as high-quality
paper that is intended for laser printers.
Air pockets inside envelopes can cause them
to wrinkle.
Remove the envelope, flatten it, and try
printing again.
Toner appears around the printed
characters.
The paper might be loaded incorrectly.
Turn over the stack of paper in the tray.
If large amounts of toner have scattered
around the characters, the paper might have
high resistivity.
Use a different paper, such as high-quality
paper that is intended for laser printers.
An image that appears at the top
of the page (in solid black)
repeats farther down the page (in
a gray field).
Software settings might affect image
printing.
In your software program, change the tone
(darkness) of the field in which the repeated
image appears.
In your software program, rotate the whole
page 180° to print the lighter image first.
The order of images printed might affect
printing.
Change the order in which the images are
printed. For example, have the lighter
image at the top of the page, and the
darker image farther down the page.
A power surge might have affected the
product.
If the defect occurs later in a print job, turn
the product off for 10 minutes, and then
turn on the product to restart the print job.
Solve image-quality problems
221
Copy print-quality problems
Problem
Cause
Solution
Images are missing or faded.
The print cartridge might be defective or
low.
Replace the print cartridge.
The original might be of poor quality.
If your original is too light or damaged, the
copy might not be able to compensate,
even if you adjust the contrast. If possible,
find an original document in better
condition.
The contrast settings might be set
incorrectly.
Use the control-panel to change the contrast
setting.
The original might have a colored
background.
Colored backgrounds might cause images
in the foreground to blend into the
background, or the background might
appear in a different shade. If possible, use
an original document without a colored
background.
Vertical white or faded stripes
appear on the copy.
The paper might not meet HP specifications.
Use paper that meets HP specifications.
The print cartridge might be defective or
low.
Replace the print cartridge.
Unwanted lines appear on the
copy.
The document feeder scanning strip might
be dirty.
Clean the document feeder scanning strip.
The photosensitive drum inside the print
cartridge might have been scratched.
Replace the print cartridge.
Ink, glue, correction fluid, or an unwanted
substance might be on the document feeder.
Clean the document feeder scanning strip.
The power to the product might have
fluctuated.
Reprint the job.
Aa BbCc
Aa BbCc
Aa BbCc
Aa BbCc
Aa BbCc
Black dots or streaks appear on
the copy.
222
Chapter 12 Solve problems
ENWW
Problem
Cause
Solution
Copies are too light or dark.
The printer driver or product software
settings may be incorrect.
Verify that the quality settings are correct.
The printer driver or product software
settings may be incorrect.
Verify that the quality settings are correct.
Text is unclear.
See the product software Help for more
information about changing the settings.
Verify that the EconoMode setting is off.
See the product software Help for more
information about changing the settings.
Scan-quality problems
Prevent scan-quality problems
The following are a few simple steps you can take to improve copy and scan quality.
●
Use high-quality originals.
●
Load the paper correctly. If the paper is loaded incorrectly, it might skew, which causes unclear
images.
●
Adjust the software settings according to how you plan to use the scanned page.
●
If your product frequently feeds more than one page at a time, the separation pad might need to
be cleaned or replaced.
●
Use or make a carrier sheet to protect your originals.
Solve scan-quality problems
ENWW
Problem
Cause
Solution
Blank pages
The original might have been loaded upside
down.
In the document feeder, put the top end of
the stack of originals into the document
feeder, with the media stack face-down and
the first page to be scanned on the bottom
of the stack.
Too light or dark
The resolution and color levels may be set
incorrectly.
Verify that you have the correct resolution
and color settings.
Unwanted lines
The document-feeder glass might be dirty.
Clean the scanner strip.
Black dots or streaks
The power to the product might have
fluctuated.
Reprint the job.
Unclear text
The resolution levels might be set
incorrectly.
Verify that the resolution settings are correct.
Solve image-quality problems
223
Repetitive defects ruler
If defects repeat at regular intervals on the page, use this ruler to identify the cause of the defect. Place
the top of the ruler at the first defect. The marking that is beside the next occurrence of the defect
indicates which component needs to be replaced.
If the defect correlates with the print engine or the fuser, the product might require service. Contact
HP Customer Care.
Figure 12-1 Repetitive defects ruler
0 mm
27 mm
29 mm
39 mm
56 mm
75 mm
224
Distance between defects
Product components that cause the defect
27 mm
Print engine
29 mm
Print engine
39 mm
Print engine
56 mm
Fuser
75 mm
Print cartridge
Chapter 12 Solve problems
ENWW
Optimize and improve image quality
Change print density
1.
Use the printer driver to change the default settings. Follow the appropriate procedure, depending
on the operating system you are using.
Windows XP, Windows Server 2003, and Windows Server 2008 (using the
default Start menu view)
a.
Click Start, and then click Printers and Faxes.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Windows XP, Windows Server 2003, and Windows Server 2008 (using the
Classic Start menu view)
a.
Click Start, click Settings, and then click Printers.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Windows Vista
a.
Click Start, click Control Panel, and then in the category for Hardware and Sound
click Printer.
b.
Right-click the driver icon, and then select Properties.
c.
Click the Device Settings tab.
Mac OS X 10.4
a.
From the Apple menu
Fax icon.
b.
Click the Printer Setup button.
, click the System Preferences menu and then click the Print &
Mac OS X 10.5 and 10.6
2.
ENWW
a.
From the Apple menu
Fax icon.
b.
Select the product in the left side of the window.
c.
Click the Options & Supplies button.
d.
Click the Driver tab.
, click the System Preferences menu and then click the Print &
Adjust the Print Density slider to change the setting.
Solve image-quality problems
225
Manage and configure printer drivers
The product uses the paper-type setting to establish many internal settings that affect print quality.
Always use the correct paper-type setting in the printer driver. Also make sure that the other settings on
the Paper/Quality tab in the printer driver are correct.
226
Chapter 12 Solve problems
ENWW
Solve performance problems
Problem
Cause
Solution
Pages print but are totally blank.
The sealing tape might still be in the
print cartridges.
Verify that the sealing tape has been
completely removed from the print
cartridges.
The document might contain blank
pages.
Check the document that you are
printing to see if content appears on all
of the pages.
The product might be malfunctioning.
To check the product, print a
Configuration page.
Heavier paper types can slow the print
job.
Print on a different type of paper.
Complex pages can print slowly.
Proper fusing may require a slower print
speed to ensure the best print quality.
The product might not be pulling paper
correctly.
Make sure paper is loaded in the tray
correctly.
The paper is jamming in the product.
Clear the jam.
The USB cable might be defective or
incorrectly connected.
●
Disconnect the USB cable at both
ends and reconnect it.
●
Try printing a job that has printed
in the past.
●
Try using a different USB cable.
Pages print very slowly.
Pages did not print.
Other devices are running on your
computer.
The product might not share a USB port.
If you have an external hard drive or
network switchbox that is connected to
the same port as the product, the other
device might be interfering. To connect
and use the product, you must
disconnect the other device or you must
use two USB ports on the computer.
Solve connectivity problems
Solve direct-connect problems
If you have connected the product directly to a computer, check the USB cable.
ENWW
●
Verify that the USB cable is connected to the computer and to the product.
●
Verify that the USB cable is not longer than 2 m (6.5 ft). Replace the cable if necessary.
●
Verify that the USB cable is working correctly by connecting it to another product. Connect the
cable to another port on the computer. Replace the cable if necessary.
Solve performance problems
227
Solve network problems
Check the following items to verify that the product is communicating with the network. Before
beginning, print a configuration page.
Problem
Solution
Poor physical connection
Verify that the product is attached to the correct network port using a cable of the
correct length.
Verify that cable connections are secure.
Look at the network port connection on the back of the product, and verify that the
amber activity light and the green link-status light are lit.
If the problem continues, try a different cable or port on the hub.
The computer is unable to communicate
with the product.
Use the command prompt to ping the product from your computer. For example:
ping 192.168.45.39
Verify that the ping displays round-trip times, which indicates that it is working.
If the ping command failed, verify that the network hubs are on, and then verify that
the network settings, the product, and the computer are all configured for the same
network.
Incorrect link and duplex settings
Hewlett-Packard recommends leaving this setting in automatic mode (the default
setting).
Incorrect IP address for the product on
the computer
Use the correct IP address. The IP address is listed on the configuration page.
Open the printer properties and click the Ports tab. Verify that the current IP
address for the product is selected.
●
If you installed the product using the HP standard TCP/IP port, select the box
labeled Always print to this printer, even if its IP address changes.
●
If you installed the product using a Microsoft standard TCP/IP port, use the
hostname instead of the IP address.
If the IP address is correct, delete the product and then add it again.
New software programs have caused
compatibility problems.
Verify that any new software programs are correctly installed and that they use the
correct printer driver.
Your computer or workstation is set up
incorrectly.
Check the network drivers, printer drivers, and the network redirection.
The protocol is disabled, or other
network settings are incorrect.
Review the configuration page to check the status of the protocol. Enable it if
necessary.
Verify that the operating system is configured correctly.
Reconfigure the network settings if necessary.
228
Chapter 12 Solve problems
ENWW
Solve software problems
Solve common Windows problems
Error message:
“(Name of the program, for example, Internet Explorer) has encountered a problem and needs to close.
We are sorry for the inconvenience”
Cause
Solution
Close all software programs, restart Windows, and try again.
If the application referenced is the printer driver, select or
install a different printer driver. If the product PCL 6 printer
driver is selected, switch to the PCL 5 or HP postscript level 3
emulation printer driver.
See the Microsoft Windows documentation that came with the
computer for more information about Windows error
messages, or go to www.microsoft.com.
Solve common Mac problems
Table 12-3 Problems in Mac OS X
The printer driver is not listed in the Printer Setup Utility or the Print & Fax list.
Cause
Solution
The product software might not have been installed or was installed
incorrectly.
Make sure that the product .GZ file is in the following hard-drive
folder:
●
Mac OS X v10.4: Library/Printers/PPDs/Contents/Resources/
<lang>.lproj, where <lang> is the two-letter language code for
the language that you are using.
●
Mac OS X v10.5 and v10.6: Library/Printers/PPDs/
Contents/Resources
If necessary, reinstall the software. See the getting started guide for
instructions.
The Postscript Printer Description (PPD) file is corrupt.
Delete the .GZ file from the following hard-drive folder:
●
Mac OS X v10.4: Library/Printers/PPDs/Contents/Resources/
<lang>.lproj, where <lang> is the two-letter language code for
the language that you are using.
●
Mac OS X v10.5 and v10.6: Library/Printers/PPDs/
Contents/Resources
Reinstall the software. See the getting started guide for instructions.
ENWW
Solve software problems
229
The product name does not appear in the product list in the Printer Setup Utility or Print & Fax list.
Cause
Solution
The product might not be ready.
Make sure that the cables are connected correctly, the product is on,
and the Ready
light is on.
The wrong product name is being used.
Print a configuration page to check the product name. Verify that the
name on the configuration page matches the product name in the
Printer Setup Utility or the Print & Fax list.
The interface cable might be defective or of poor quality.
Replace the cable with a high-quality cable.
The printer driver does not automatically set up the selected product in the Printer Setup Utility or the Print & Fax
list.
Cause
Solution
The product might not be ready.
Make sure that the cables are connected correctly, the product is on,
and the Ready
light is on.
The product software might not have been installed or was installed
incorrectly.
Make sure that the product PPD is in the following hard-drive folder:
●
Mac OS X v10.4: Library/Printers/PPDs/Contents/Resources/
<lang>.lproj, where <lang> is the two-letter language code for
the language that you are using.
●
Mac OS X v10.5 and v10.6: Library/Printers/PPDs/
Contents/Resources
If necessary, reinstall the software. See the getting started guide for
instructions.
The Postscript Printer Description (PPD) file is corrupt.
Delete the .GZ file from the following hard-drive folder:
●
Mac OS X v10.4: Library/Printers/PPDs/Contents/Resources/
<lang>.lproj, where <lang> is the two-letter language code for
the language that you are using.
●
Mac OS X v10.5 and v10.6: Library/Printers/PPDs/
Contents/Resources
Reinstall the software. See the getting started guide for instructions.
The interface cable might be defective or of poor quality.
Replace the interface cable with a high-quality cable.
A print job was not sent to the product that you wanted.
Cause
Solution
The print queue might be stopped.
Restart the print queue. Open print monitor and select Start
Jobs.
The wrong product name is being used. Another product with the
same or similar name might have received your print job.
Print a configuration page to check the product name. Verify that the
name on the configuration page matches the product name in the
Printer Setup Utility or Print & Fax list.
230
Chapter 12 Solve problems
ENWW
You are unable to print from a third-party USB card.
Cause
Solution
This error occurs when the software for USB products is not installed.
When adding a third-party USB card, you might need the Apple
USB Adapter Card Support software. The most current version of this
software is available from the Apple Web site.
When connected with a USB cable, the product does not appear in the Printer Setup Utility or Print & Fax list after
the driver is selected.
Cause
Solution
This problem is caused by either a software or a hardware
component.
Software troubleshooting
●
Check that your Mac supports USB.
●
Verify that your Mac operating system is Mac OS X v10.4 or
later.
●
Ensure that your Mac has the appropriate USB software from
Apple.
Hardware troubleshooting
●
Check that the product is turned on.
●
Verify that the USB cable is connected correctly.
●
Check that you are using the appropriate high-speed USB
cable.
●
Ensure that you do not have too many USB devices drawing
power from the chain. Disconnect all of the devices from the
chain, and connect the cable directly to the USB port on the
host computer.
●
Check to see if more than two non-powered USB hubs are
connected in a row on the chain. Disconnect all of the devices
from the chain, and then connect the cable directly to the USB
port on the host computer.
NOTE:
ENWW
The iMac keyboard is a non-powered USB hub.
Solve software problems
231
232
Chapter 12 Solve problems
ENWW
A
ENWW
Supplies and accessories
●
Order parts, accessories, and supplies
●
Part numbers
233
Order parts, accessories, and supplies
Order supplies and paper
www.hp.com/go/suresupply
Order genuine HP parts or accessories
www.hp.com/buy/parts
Order through service or support providers
Contact an HP-authorized service or support provider.
Part numbers
The following list of accessories was current at the time of printing. Ordering information and
availability of the accessories might change during the life of the product.
Paper-handling accessories
Item
Description
Part number
Pickup roller
Pickup roller for input tray
RL1-1443-000CN
Separation pad assembly
Separation pad for input tray
RM1-4006-000CN
Item
Description
Part number
HP LaserJet print cartridge
Black print cartridge
See one the following items to determine
the print cartridge part number.
Print cartridges
●
The configuration page
●
The supplies status page
●
The current print cartridge
●
www.hp.com/go/ljsupplies
Cables and interfaces
234
Item
Description
Part number
USB cable
2-meter A-to-B cable
8121-0868
Appendix A Supplies and accessories
ENWW
B
ENWW
Service and support
●
Hewlett-Packard limited warranty statement
●
HP's Premium Protection Warranty: LaserJet print cartridge limited warranty statement
●
End User License Agreement
●
Customer self-repair warranty service
●
Customer support
●
Repack the product
●
Service information form
235
Hewlett-Packard limited warranty statement
HP PRODUCT
DURATION OF LIMITED WARRANTY
HP LaserJet Professional M1130, M1210
One year from date of purchase
HP warrants to you, the end-user customer, that HP hardware and accessories will be free from defects
in materials and workmanship after the date of purchase, for the period specified above. If HP receives
notice of such defects during the warranty period, HP will, at its option, either repair or replace
products which prove to be defective. Replacement products may be either new or equivalent in
performance to new.
HP warrants to you that HP software will not fail to execute its programming instructions after the date
of purchase, for the period specified above, due to defects in material and workmanship when
properly installed and used. If HP receives notice of such defects during the warranty period, HP will
replace software which does not execute its programming instructions due to such defects.
HP does not warrant that the operation of HP products will be uninterrupted or error free. If HP is
unable, within a reasonable time, to repair or replace any product to a condition as warranted, you
will be entitled to a refund of the purchase price upon prompt return of the product.
HP products may contain remanufactured parts equivalent to new in performance or may have been
subject to incidental use.
Warranty does not apply to defects resulting from (a) improper or inadequate maintenance or
calibration, (b) software, interfacing, parts or supplies not supplied by HP, (c) unauthorized
modification or misuse, (d) operation outside of the published environmental specifications for the
product, or (e) improper site preparation or maintenance.
TO THE EXTENT ALLOWED BY LOCAL LAW, THE ABOVE WARRANTIES ARE EXCLUSIVE AND NO
OTHER WARRANTY OR CONDITION, WHETHER WRITTEN OR ORAL, IS EXPRESSED OR IMPLIED
AND HP SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY, SATISFACTORY QUALITY, AND FITNESS FOR A PARTICULAR PURPOSE. Some
countries/regions, states or provinces do not allow limitations on the duration of an implied warranty,
so the above limitation or exclusion might not apply to you. This warranty gives you specific legal rights
and you might also have other rights that vary from country/region to country/region, state to state, or
province to province.
HP's limited warranty is valid in any country/region or locality where HP has a support presence for
this product and where HP has marketed this product. The level of warranty service you receive may
vary according to local standards. HP will not alter form, fit or function of the product to make it
operate in a country/region for which it was never intended to function for legal or regulatory reasons.
TO THE EXTENT ALLOWED BY LOCAL LAW, THE REMEDIES IN THIS WARRANTY STATEMENT ARE
YOUR SOLE AND EXCLUSIVE REMEDIES. EXCEPT AS INDICATED ABOVE, IN NO EVENT WILL HP OR
ITS SUPPLIERS BE LIABLE FOR LOSS OF DATA OR FOR DIRECT, SPECIAL, INCIDENTAL,
CONSEQUENTIAL (INCLUDING LOST PROFIT OR DATA), OR OTHER DAMAGE, WHETHER BASED
IN CONTRACT, TORT, OR OTHERWISE. Some countries/regions, states or provinces do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may
not apply to you.
THE WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO THE EXTENT LAWFULLY
PERMITTED, DO NOT EXCLUDE, RESTRICT OR MODIFY AND ARE IN ADDITION TO THE
MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU.
236
Appendix B Service and support
ENWW
HP's Premium Protection Warranty: LaserJet print
cartridge limited warranty statement
This HP product is warranted to be free from defects in materials and workmanship.
This warranty does not apply to products that (a) have been refilled, refurbished, remanufactured or
tampered with in any way, (b) experience problems resulting from misuse, improper storage, or
operation outside of the published environmental specifications for the printer product or (c) exhibit
wear from ordinary use.
To obtain warranty service, please return the product to place of purchase (with a written description of
the problem and print samples) or contact HP customer support. At HP's option, HP will either replace
products that prove to be defective or refund your purchase price.
TO THE EXTENT ALLOWED BY LOCAL LAW, THE ABOVE WARRANTY IS EXCLUSIVE AND NO
OTHER WARRANTY OR CONDITION, WHETHER WRITTEN OR ORAL, IS EXPRESSED OR IMPLIED
AND HP SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY, SATISFACTORY QUALITY, AND FITNESS FOR A PARTICULAR PURPOSE.
TO THE EXTENT ALLOWED BY LOCAL LAW, IN NO EVENT WILL HP OR ITS SUPPLIERS BE LIABLE
FOR DIRECT, SPECIAL, INCIDENTAL, CONSEQUENTIAL (INCLUDING LOST PROFIT OR DATA), OR
OTHER DAMAGE, WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.
THE WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT TO THE EXTENT LAWFULLY
PERMITTED, DO NOT EXCLUDE, RESTRICT OR MODIFY AND ARE IN ADDITION TO THE
MANDATORY STATUTORY RIGHTS APPLICABLE TO THE SALE OF THIS PRODUCT TO YOU.
ENWW
HP's Premium Protection Warranty: LaserJet print cartridge limited warranty statement
237
End User License Agreement
PLEASE READ CAREFULLY BEFORE USING THIS SOFTWARE PRODUCT: This End-User License
Agreement (“EULA”) is a contract between (a) you (either an individual or the entity you represent) and
(b) Hewlett-Packard Company (“HP”) that governs your use of the software product (“Software”). This
EULA does not apply if there is a separate license agreement between you and HP or its suppliers for
the Software, including a license agreement in online documentation. The term “Software” may include
(i) associated media, (ii) a user guide and other printed materials, and (iii) “online” or electronic
documentation (collectively “User Documentation”).
RIGHTS IN THE SOFTWARE ARE OFFERED ONLY ON THE CONDITION THAT YOU AGREE TO ALL
TERMS AND CONDITIONS OF THIS EULA. BY INSTALLING, COPYING, DOWNLOADING, OR
OTHERWISE USING THE SOFTWARE, YOU AGREE TO BE BOUND BY THIS EULA. IF YOU DO NOT
ACCEPT THIS EULA, DO NOT INSTALL, DOWNLOAD, OR OTHERWISE USE THE SOFTWARE. IF
YOU PURCHASED THE SOFTWARE BUT DO NOT AGREE TO THIS EULA, PLEASE RETURN THE
SOFTWARE TO YOUR PLACE OF PURCHASE WITHIN FOURTEEN DAYS FOR A REFUND OF THE
PURCHASE PRICE; IF THE SOFTWARE IS INSTALLED ON OR MADE AVAILABLE WITH ANOTHER
HP PRODUCT, YOU MAY RETURN THE ENTIRE UNUSED PRODUCT.
1. THIRD PARTY SOFTWARE. The Software may include, in addition to HP proprietary software
(“HP Software”), software under licenses from third parties (“Third Party Software” and “Third Party
License”). Any Third Party Software is licensed to you subject to the terms and conditions of the
corresponding Third Party License. Generally, the Third Party License is located in a file such as
license.txt; you should contact HP support if you cannot find any Third Party License. If the Third Party
Licenses include licenses that provide for the availability of source code (such as the GNU General
Public License) and the corresponding source code is not included with the Software, then check the
product support pages of HP’s website (hp.com) to learn how to obtain such source code.
2. LICENSE RIGHTS. You will have the following rights provided you comply with all terms and
conditions of this EULA:
a. Use. HP grants you a license to Use one copy of the HP Software. “Use” means installing, copying,
storing, loading, executing, displaying, or otherwise using the HP Software. You may not modify the
HP Software or disable any licensing or control feature of the HP Software. If this Software is provided
by HP for Use with an imaging or printing product (for example, if the Software is a printer driver,
firmware, or add-on), the HP Software may only be used with such product (“HP Product”). Additional
restrictions on Use may appear in the User Documentation. You may not separate component parts of
the HP Software for Use. You do not have the right to distribute the HP Software.
b. Copying. Your right to copy means you may make archival or back-up copies of the HP Software,
provided each copy contains all the original HP Software’s proprietary notices and is used only for
back-up purposes.
3. UPGRADES. To Use HP Software provided by HP as an upgrade, update, or supplement (collectively
“Upgrade”), you must first be licensed for the original HP Software identified by HP as eligible for the
Upgrade. To the extent the Upgrade supersedes the original HP Software, you may no longer use such
HP Software. This EULA applies to each Upgrade unless HP provides other terms with the Upgrade. In
case of a conflict between this EULA and such other terms, the other terms will prevail.
4. TRANSFER.
a. Third Party Transfer. The initial end user of the HP Software may make a one-time transfer of the
HP Software to another end user. Any transfer will include all component parts, media, User
Documentation, this EULA, and if applicable, the Certificate of Authenticity. The transfer may not be an
indirect transfer, such as a consignment. Prior to the transfer, the end user receiving the transferred
238
Appendix B Service and support
ENWW
Software will agree to this EULA. Upon transfer of the HP Software, your license is automatically
terminated.
b. Restrictions. You may not rent, lease or lend the HP Software or Use the HP Software for commercial
timesharing or bureau use. You may not sublicense, assign or otherwise transfer the HP Software
except as expressly provided in this EULA.
5. PROPRIETARY RIGHTS. All intellectual property rights in the Software and User Documentation are
owned by HP or its suppliers and are protected by law, including applicable copyright, trade secret,
patent, and trademark laws. You will not remove any product identification, copyright notice, or
proprietary restriction from the Software.
6. LIMITATION ON REVERSE ENGINEERING. You may not reverse engineer, decompile, or
disassemble the HP Software, except and only to the extent that the right to do so is allowed under
applicable law.
7. CONSENT TO USE OF DATA. HP and its affiliates may collect and use technical information you
provide in relation to (i) your Use of the Software or the HP Product, or (ii) the provision of support
services related to the Software or the HP Product. All such information will be subject to HP’s privacy
policy. HP will not use such information in a form that personally identifies you except to the extent
necessary to enhance your Use or provide support services.
8. LIMITATION OF LIABILITY. Notwithstanding any damages that you might incur, the entire liability of
HP and its suppliers under this EULA and your exclusive remedy under this EULA will be limited to the
greater of the amount actually paid by you for the Product or U.S. $5.00. TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, IN NO EVENT WILL HP OR ITS SUPPLIERS BE LIABLE FOR ANY
SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR
LOST PROFITS, LOST DATA, BUSINESS INTERRUPTION, PERSONAL INJURY, OR LOSS OF PRIVACY)
RELATED IN ANY WAY TO THE USE OF OR INABILITY TO USE THE SOFTWARE, EVEN IF HP OR
ANY SUPPLIER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES AND EVEN IF THE
ABOVE REMEDY FAILS OF ITS ESSENTIAL PURPOSE. Some states or other jurisdictions do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you.
9. U.S. GOVERNMENT CUSTOMERS. If you are a U.S. Government entity, then consistent with FAR
12.211 and FAR 12.212, Commercial Computer Software, Computer Software Documentation, and
Technical Data for Commercial Items are licensed under the applicable HP commercial license
agreement.
10. COMPLIANCE WITH EXPORT LAWS. You will comply with all laws, rules, and regulations (i)
applicable to the export or import of the Software, or (ii) restricting the Use of the Software, including
any restrictions on nuclear, chemical, or biological weapons proliferation.
11. RESERVATION OF RIGHTS. HP and its suppliers reserve all rights not expressly granted to you in
this EULA.
(c) 2007 Hewlett-Packard Development Company, L.P.
Rev. 11/06
ENWW
End User License Agreement
239
Customer self-repair warranty service
HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and
allow for greater flexibility in performing defective parts replacement. If during the diagnosis period,
HP identifies that the repair can be accomplished by the use of a CSR part, HP will ship that part
directly to you for replacement. There are two categories of CSR parts: 1) Parts for which customer self
repair is mandatory. If you request HP to replace these parts, you will be charged for the travel and
labor costs of this service. 2) Parts for which customer self repair is optional. These parts are also
designed for Customer Self Repair. If, however, you require that HP replace them for you, this may be
done at no additional charge under the type of warranty service designated for your product.
Based on availability and where geography permits, CSR parts will be shipped for next business day
delivery. Same-day or four-hour delivery may be offered at an additional charge where geography
permits. If assistance is required, you can call the HP Technical Support Center and a technician will
help you over the phone. HP specifies in the materials shipped with a replacement CSR part whether a
defective part must be returned to HP. In cases where it is required to return the defective part to HP,
you must ship the defective part back to HP within a defined period of time, normally five (5) business
days. The defective part must be returned with the associated documentation in the provided shipping
material. Failure to return the defective part may result in HP billing you for the replacement. With a
customer self repair, HP will pay all shipping and part return costs and determine the courier/carrier to
be used.
Customer support
Get telephone support, free during your warranty period, for
your country/region
Country/region phone numbers are on the flyer that was in
the box with your product or at www.hp.com/support/.
Have the product name, serial number, date of purchase, and
problem description ready.
240
Get 24-hour Internet support
www.hp.com/support/ljm1130series or www.hp.com/
support/ljm1210series
Get support for products used with a Macintosh computer
www.hp.com/go/macosx
Download software utilities, drivers, and electronic
information
www.hp.com/go/ljm1130series_software or www.hp.com/
go/ljm1210series_software
Order additional HP service or maintenance agreements
www.hp.com/go/carepack
Appendix B Service and support
ENWW
Repack the product
If HP Customer Care determines that your product needs to be returned to HP for repair, follow these
steps to repack the product before shipping it.
CAUTION: Shipping damage as a result of inadequate packing is the customer’s responsibility.
1.
Remove and retain the print cartridge.
CAUTION: It is extremely important to remove the print cartridge before shipping the product. A
print cartridge that remains in the product during shipping can leak and cover the product engine
and other parts with toner.
To prevent damage to the print cartridge, avoid touching the roller on it, and store the print
cartridge in its original packing material or so that it is not exposed to light.
ENWW
2.
Remove and retain the power cable, interface cable, and optional accessories, such as an EIO
card.
3.
If possible, include print samples and 50 to 100 sheets of paper or other print media that did not
print correctly.
4.
In the U.S., call HP Customer Care to request new packing material. In other areas, use the
original packing material, if possible. Hewlett-Packard recommends insuring the equipment for
shipment.
Repack the product
241
Service information form
WHO IS RETURNING THE EQUIPMENT?
Date:
Person to contact:
Phone:
Alternate contact:
Phone:
Return shipping address:
Special shipping instructions:
WHAT ARE YOU SENDING?
Model name:
Model number:
Serial number:
Please attach any relevant printouts. Do NOT ship accessories (manuals, cleaning supplies, and so on) that are not required to complete the
repair.
HAVE YOU REMOVED THE PRINT CARTRIDGES?
You must remove them before shipping the printer, unless a mechanical problem prevents you from doing so.
[ ] Yes.
[ ] No, I cannot remove them.
WHAT NEEDS TO BE DONE? (Attach a separate sheet if necessary.)
1. Describe the conditions of the failure. (What was the failure? What were you doing when the failure occurred? What software were you
running? Is the failure repeatable?)
2. If the failure is intermittent, how much time elapses between failures?
3. If the unit connected to any of the following, give the manufacturer and model number.
Personal computer:
Modem:
Network:
4. Additional comments:
HOW WILL YOU PAY FOR THE REPAIR?
[ ] Under warranty
Purchase/received date:
(Attach proof of purchase or receiving document with original received date.)
[ ] Maintenance contract number:
[ ] Purchase order number:
Except for contract and warranty service, a purchase order number and/or authorized signature must accompany
any request for service. If standard repair prices do not apply, a minimum purchase order is required. Standard repair prices can be
obtained by contacting an HP-authorized repair center.
242
Appendix B Service and support
ENWW
Authorized signature:
Billing address:
ENWW
Phone:
Special billing instructions:
Service information form
243
244
Appendix B Service and support
ENWW
C
ENWW
Specifications
●
Physical specifications
●
Power consumption, electrical specifications, and acoustic emissions
●
Environmental specifications
245
Physical specifications
Table C-1 Physical specifications1
1
Specification
M1130 Series
M1210 Series
Product weight
7.0 kg (15.4 lb)
8.3 kg (18.3 lb)
Product height
250 mm (9.8 in)
306 mm (12.0 in)
Product depth
265 mm (10.4 in)
265 mm (10.4 in)
Product width
415 mm (16.3 in)
435 mm (17.1 in)
Values are based on preliminary data. See www.hp.com/support/ljm1130series or www.hp.com/support/ljm1210series.
Power consumption, electrical specifications, and
acoustic emissions
See www.hp.com/go/ljm1130series_regulatory or www.hp.com/go/ljm1210series_regulatory for
current information.
CAUTION: Power requirements are based on the country/region where the product is sold. Do not
convert operating voltages. This will damage the product and void the product warranty.
Environmental specifications
Table C-2 Environmental specifications
1
246
Operating1
Storage1
Temperature
15° to 32.5°C (59° to 90.5°F)
0° to 35°C (32° to 95°F)
Relative Humidity
10% to 80%
10% to 80%
Values are based on preliminary data. See www.hp.com/support/ljm1130series or www.hp.com/support/ljm1210series.
Appendix C Specifications
ENWW
D
ENWW
Regulatory information
●
FCC regulations
●
Environmental product stewardship program
●
Declaration of conformity (base model)
●
Declaration of conformity (fax model)
●
Safety statements
●
Additional statements for telecom (fax) products
247
FCC regulations
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy. If this equipment is not installed and used in accordance with the
instructions, it may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
●
Reorient or relocate the receiving antenna.
●
Increase separation between equipment and receiver.
●
Connect equipment to an outlet on a circuit different from that to which the receiver is located.
●
Consult your dealer or an experienced radio/TV technician.
NOTE: Any changes or modifications to the printer that are not expressly approved by HP could void
the user’s authority to operate this equipment.
Use of a shielded interface cable is required to comply with the Class B limits of Part 15 of FCC rules.
Environmental product stewardship program
Protecting the environment
Hewlett-Packard Company is committed to providing quality products in an environmentally sound
manner. This product has been designed with several attributes to minimize impacts on our
environment.
Ozone production
This product generates no appreciable ozone gas (O3).
Power consumption
Power usage drops significantly while in Ready or Auto-Off mode, which saves natural resources and
saves money without affecting the high performance of this product. Hewlett-Packard printing and
imaging equipment marked with the ENERGY STAR® logo is qualified to the U.S. Environmental
Protection Agency's ENERGY STAR specifications for imaging equipment. The following mark will
appear on ENERGY STAR qualified imaging products:
Additional ENERGY STAR qualified imaging product model information is listed at:
248
Appendix D Regulatory information
ENWW
www.hp.com/go/energystar
Toner consumption
EconoMode uses less toner, which might extend the life of the print cartridge.
Paper use
This product’s manual duplex feature (two-sided printing) and N-up printing (multiple pages printed on
one page) capability can reduce paper usage and the resulting demands on natural resources.
Plastics
Plastic parts over 25 grams are marked according to international standards that enhance the ability to
identify plastics for recycling purposes at the end of the product’s life.
HP LaserJet print supplies
It’s easy to return and recycle your HP LaserJet print cartridges after use—free of charge—with
HP Planet Partners. Multilingual program information and instructions are included in every new
HP LaserJet print cartridge and supplies package. You help reduce the toll on the environment further
when you return multiple cartridges together rather than separately.
HP is committed to providing inventive, high-quality products and services that are environmentally
sound, from product design and manufacturing to distribution, customer use and recycling. When you
participate in the HP Planet Partners program, we ensure your HP LaserJet print cartridges are recycled
properly, processing them to recover plastics and metals for new products and diverting millions of tons
of waste from landfills. Since this cartridge is being recycled and used in new materials, it will not be
returned to you. Thank you for being environmentally responsible!
NOTE: Use the return label to return original HP LaserJet print cartridges only. Please do not use this
label for HP inkjet cartridges, non-HP cartridges, refilled or remanufactured cartridges or warranty
returns. For information about recycling your HP inkjet cartridges please go to http://www.hp.com/
recycle.
Return and recycling instructions
United States and Puerto Rico
The enclosed label in the HP LaserJet toner cartridge box is for the return and recycling of one or more
HP LaserJet print cartridges after use. Please follow the applicable instructions below.
Multiple returns (more than one cartridge)
ENWW
1.
Package each HP LaserJet print cartridge in its original box and bag.
2.
Tape the boxes together using strapping or packaging tape. The package can weigh up to 31 kg
(70 lb).
3.
Use a single pre-paid shipping label.
Environmental product stewardship program
249
OR
1.
Use your own suitable box, or request a free bulk collection box from www.hp.com/recycle or
1-800-340-2445 (holds up to 31 kg (70 lb) of HP LaserJet print cartridges).
2.
Use a single pre-paid shipping label.
Single returns
1.
Package the HP LaserJet print cartridge in its original bag and box.
2.
Place the shipping label on the front of the box.
Shipping
For all HP LaserJet print cartridge recycling returns, give the package to UPS during your next delivery
or pickup, or take it to an authorized UPS drop-off center. For the location of your local UPS drop-off
center, call 1-800-PICKUPS or visit www.ups.com. If you are returning via USPS label, give the
package to a U.S. Postal Service carrier or drop off at a U.S. Postal Service Office. For more
information, or to order additional labels or boxes for bulk returns, visit www.hp.com/recycle or call
1-800-340-2445. Requested UPS pickup will be charged normal pickup rates. Information subject to
change without notice.
Residents of Alaska and Hawaii
Do not use the UPS label. Call 1-800-340-2445 for information and instructions. The U.S. Postal
Service provides no-cost cartridge return transportation services under an arrangement with HP for
Alaska and Hawaii.
Non-U.S. returns
To participate in HP Planet Partners return and recycling program, just follow the simple directions in
the recycling guide (found inside the packaging of your new product supply item) or visit
www.hp.com/recycle. Select your country/region for information on how to return your HP LaserJet
printing supplies.
Paper
This product is capable of using recycled papers when the paper meets the guidelines outlined in the
HP LaserJet Printer Family Print Media Guide. This product is suitable for the use of recycled paper
according to EN12281:2002.
Material restrictions (M1130 Series)
This HP product does not contain added mercury.
This HP product does not contain a battery.
Material restrictions (M1210 Series)
This HP product does not contain added mercury.
250
Appendix D Regulatory information
ENWW
This HP product contains a battery that might require special handling at end-of-life. The batteries
contained in or supplied by Hewlett-Packard for this product include the following:
HP LaserJet Professional M1210 MFP Series
Type
Carbon monofluoride lithium
Weight
0.8 g
Location
On formatter board
User-removable
No
For recycling information, you can go to www.hp.com/recycle, or contact your local authorities or the
Electronics Industries Alliance: www.eiae.org.
Disposal of waste equipment by users in private households in the
European Union
This symbol on the product or on its packaging indicates that this product must not be disposed of with
your other household waste. Instead, it is your responsibility to dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at the time of disposal will
help to conserve natural resources and ensure that it is recycled in a manner that protects human health
and the environment. For more information about where you can drop off your waste equipment for
recycling, please contact your local city office, your household waste disposal service or the shop
where you purchased the product.
Chemical substances
HP is committed to providing our customers with information about the chemical substances in our
products as needed to comply with legal requirements such as REACH (Regulation EC No 1907/2006
of the European Parliament and the Council). A chemical information report for this product can be
found at: www.hp.com/go/reach.
Material Safety Data Sheet (MSDS)
Material Safety Data Sheets (MSDS) for supplies containing chemical substances (for example, toner)
can be obtained by accessing the HP Web site at www.hp.com/go/msds or www.hp.com/hpinfo/
community/environment/productinfo/safety.
ENWW
Environmental product stewardship program
251
For more information
To obtain information about these environmental topics:
●
Product environmental profile sheet for this and many related HP products
●
HP’s commitment to the environment
●
HP’s environmental management system
●
HP’s end-of-life product return and recycling program
●
Material Safety Data Sheets
Visit www.hp.com/go/environment or www.hp.com/hpinfo/globalcitizenship/environment.
252
Appendix D Regulatory information
ENWW
Declaration of conformity (base model)
Declaration of Conformity
according to ISO/IEC 17050-1 and EN 17050-1
Manufacturer's Name:
Manufacturer's Address:
DoC#: BOISB-0901-02-rel.1.0
Hewlett-Packard Company
11311 Chinden Boulevard,
Boise, Idaho 83714-1021, USA
declares, that the product
Product Name:
HP LaserJet M1132 Series; HP LaserJet M1134 Series; HP LaserJet M1136 Series
Regulatory Model Number
Product Options:
Print Cartridges:
2)
BOISB-0901-02
ALL
CE284A, CE285A, CE286A
conforms to the following Product Specifications:
SAFETY:
IEC 60950-1:2001 / EN60950-1: 2001 +A11
IEC 60825-1:1993 +A1 +A2 / EN 60825-1:1994 +A1 +A2 (Class 1 Laser/LED Product)
GB4943-2001
EMC:
CISPR22:2005 +A1:2005 / EN55022:2006 +A1:2007 – Class B1)
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1 +A2
EN 55024:1998 +A1 +A2
FCC Title 47 CFR, Part 15 Class B / ICES-003, Issue 4
GB9254-1998, GB17625.1-2003
Supplementary Information:
The product herewith complies with the requirements of the EMC Directive 2004/108/EC and the Low Voltage Directive 2006/95/EC, and
carries the CE-Marking
accordingly.
This Device complies with Part 15 of the FCC Rules. Operation is subject to the following two Conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
1) The product was tested in a typical configuration with Hewlett-Packard Personal Computer Systems.
2) For regulatory purposes, this product is assigned a Regulatory model number. This number should not be confused with the product name
or the product number(s).
Boise, Idaho , USA
December, 2009
For regulatory topics only:
European Contact:
Your Local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Department HQ-TRE / Standards
Europe,, Herrenberger Strasse 140, , D-71034, Böblingen, (FAX: +49-7031-14-3143), http://www.hp.com/go/
certificates
USA Contact:
Product Regulations Manager, Hewlett-Packard Company,, PO Box 15, Mail Stop 160, Boise, ID 83707-0015, ,
(Phone: 208-396-6000)
ENWW
Declaration of conformity (base model)
253
Declaration of conformity (fax model)
Declaration of Conformity
according to ISO/IEC 17050-1 and EN 17050-1
Manufacturer's Name:
Manufacturer's Address:
DoC#: BOISB-0901-03-rel.1.0
Hewlett-Packard Company
11311 Chinden Boulevard,
Boise, Idaho 83714-1021, USA
declares, that the product
Product Name:
HP LaserJet M1212 Series; HP LaserJet M1214 Series; HP LaserJet M1216 Series
Accessories :
BOISB-0906-00 - (US-Fax Module LIU)
BOISB-0906-01 - (EURO-Fax Module LIU)
Regulatory Model Number2)
Product Options:
Print Cartridges:
BOISB-0901-03
ALL
CE284A, CE285A, CE286A
4)
conforms to the following Product Specifications:
SAFETY:
IEC 60950-1:2001 / EN60950-1: 2001 +A11
IEC 60825-1:1993 +A1 +A2 / EN 60825-1:1994 +A1 +A2 (Class 1 Laser/LED Product)
GB4943-2001
EMC:
CISPR22:2005 +A1:2005 / EN55022:2006 +A1:2007 – Class B1)
EN 61000-3-2:2006
EN 61000-3-3:1995 +A1 +A2
EN 55024:1998 +A1 +A2
FCC Title 47 CFR, Part 15 Class B / ICES-003, Issue 4
GB9254-1998, GB17625.1-2003
TELECOM:
ES 203 021; FCC Title 47 CFR, Part 683)
Supplementary Information:
The product herewith complies with the requirements of the EMC Directive 2004/108/EC and the Low Voltage Directive 2006/95/EC, the
R&TTE Directive 1999/5/EC (Annex II), and carries the CE-Marking
accordingly.
This Device complies with Part 15 of the FCC Rules. Operation is subject to the following two Conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
1) The product was tested in a typical configuration with Hewlett-Packard Personal Computer Systems.
2) For regulatory purposes, this product is assigned a Regulatory model number. This number should not be confused with the product name
or the product number(s).
3) Telecom approvals and standards appropriate for the target countries/regions have been applied to this product, in addition to those
listed above.
4) This product uses an analog fax accessory module which Regulatory Model numbers are: BOISB-0906-00 (US-LIU) or BOISB-0906-01
(EURO LIU), as needed to meet technical regulatory requirements for the countries/regions this product will be sold.
Boise, Idaho , USA
December, 2009
For regulatory topics only:
European Contact:
Your Local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Department HQ-TRE / Standards
Europe,, Herrenberger Strasse 140, , D-71034, Böblingen, (FAX: +49-7031-14-3143), http://www.hp.com/go/
certificates
USA Contact:
Product Regulations Manager, Hewlett-Packard Company,, PO Box 15, Mail Stop 160, Boise, ID 83707-0015, ,
(Phone: 208-396-6000)
254
Appendix D Regulatory information
ENWW
Safety statements
Laser safety
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration has
implemented regulations for laser products manufactured since August 1, 1976. Compliance is
mandatory for products marketed in the United States. The device is certified as a “Class 1” laser
product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance
Standard according to the Radiation Control for Health and Safety Act of 1968. Since radiation
emitted inside the device is completely confined within protective housings and external covers, the
laser beam cannot escape during any phase of normal user operation.
WARNING! Using controls, making adjustments, or performing procedures other than those
specified in this user guide may result in exposure to hazardous radiation.
Canadian DOC regulations
Complies with Canadian EMC Class B requirements.
« Conforme à la classe B des normes canadiennes de compatibilité électromagnétiques. « CEM ». »
Power cord instructions
Make sure your power source is adequate for the product voltage rating. The voltage rating is on the
product label. The product uses either 110-127 Vac or 220-240 Vac and 50/60 Hz.
Connect the power cord between the product and a grounded AC outlet.
CAUTION: To prevent damage to the product, use only the power cord that is provided with the
product.
EMC statement (Korea)
ENWW
Safety statements
255
Laser statement for Finland
Luokan 1 laserlaite
Klass 1 Laser Apparat
HP LaserJet Professional M1132/M1134/M1136, M1212/M1214/M1216, laserkirjoitin on
käyttäjän kannalta turvallinen luokan 1 laserlaite. Normaalissa käytössä kirjoittimen suojakotelointi
estää lasersäteen pääsyn laitteen ulkopuolelle. Laitteen turvallisuusluokka on määritetty standardin EN
60825-1 (1994) mukaisesti.
VAROITUS !
Laitteen käyttäminen muulla kuin käyttöohjeessa mainitulla tavalla saattaa altistaa käyttäjän
turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle.
VARNING !
Om apparaten används på annat sätt än i bruksanvisning specificerats, kan användaren utsättas för
osynlig laserstrålning, som överskrider gränsen för laserklass 1.
HUOLTO
HP LaserJet Professional M1132/M1134/M1136, M1212/M1214/M1216 - kirjoittimen sisällä ei ole
käyttäjän huollettavissa olevia kohteita. Laitteen saa avata ja huoltaa ainoastaan sen huoltamiseen
koulutettu henkilö. Tällaiseksi huoltotoimenpiteeksi ei katsota väriainekasetin vaihtamista, paperiradan
puhdistusta tai muita käyttäjän käsikirjassa lueteltuja, käyttäjän tehtäväksi tarkoitettuja ylläpitotoimia,
jotka voidaan suorittaa ilman erikoistyökaluja.
VARO !
Mikäli kirjoittimen suojakotelo avataan, olet alttiina näkymättömällelasersäteilylle laitteen ollessa
toiminnassa. Älä katso säteeseen.
VARNING !
Om laserprinterns skyddshölje öppnas då apparaten är i funktion, utsättas användaren för osynlig
laserstrålning. Betrakta ej strålen. Tiedot laitteessa käytettävän laserdiodin säteilyominaisuuksista:
Aallonpituus 775-795 nm Teho 5 m W Luokan 3B laser.
GS statement (Germany)
Das Gerät ist nicht für die Benutzung im unmittelbaren Gesichtsfeld am Bildschirmarbeitsplatz
vorgesehen. Um störende Reflexionen am Bildschirmarbeitsplatz zu vermeiden, darf dieses Produkt
nicht im unmittelbaren Gesichtsfeld platziert werden.
256
Appendix D Regulatory information
ENWW
Substances Table (China)
Restriction on Hazardous Substances statement (Turkey)
Türkiye Cumhuriyeti: EEE Yönetmeliğine Uygundur
ENWW
Safety statements
257
Additional statements for telecom (fax) products
EU Statement for Telecom Operation
This product is intended to be connected to the analog Public Switched Telecommunication Networks
(PSTN) of European Economic Area (EEA) countries/regions.
It meets requirements of EU R&TTE Directive 1999/5/EC (Annex II) and carries appropriate CE
conformity marking.
For more details see Declaration of Conformity issued by the manufacturer in another section of this
manual.
However due to differences between individual national PSTNs the product may not guarantee
unconditional assurance of successful operation on every PSTN termination point. Network
compatibility depends on the correct setting being selected by the customer in preparation of its
connection to the PSTN. Please follow the instructions provided in the user manual.
If you experience network compatibility issues, please contact your equipment supplier or HewlettPackard help desk in the country/region of operation.
Connecting to a PSTN termination point may be the subject of additional requirements set out by the
local PSTN operator.
New Zealand Telecom Statements
The grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted
that the item complies with minimum conditions for connection to its network. It indicates no
endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides
no assurance that any item will work correctly in all respects with another item of Telepermitted
equipment of a different make or model, nor does it imply that any product is compatible with all of
Telecom’s network services.
This equipment may not provide for the effective hand-over of a call to another device connected to the
same line.
This equipment shall not be set up to make automatic calls to the Telecom “111” Emergency Service.
This product has not been tested to ensure compatibility with the FaxAbility distinctive ring service for
New Zealand.
Additional FCC statement for telecom products (US)
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On
the back of this equipment is a label that contains, among other information, a product identifier in the
format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
The REN is used to determine the quantity of devices, which may be connected to the telephone line.
Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming
call. In most, but not all, areas, the sum of the RENs should not exceed five (5.0). To be certain of the
number of devices that may be connected to the line, as determined by the total RENs, contact the
telephone company to determine the maximum REN for the calling area.
This equipment uses the following USOC jacks: RJ11C.
258
Appendix D Regulatory information
ENWW
An FCC-compliant telephone cord and modular plug is provided with this equipment. This equipment is
designed to be connected to the telephone network or premises wiring using a compatible modular
jack, which is Part 68 compliant. This equipment cannot be used on telephone company-provided coin
service. Connection to Party Line Service is subject to state tariffs.
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. If advance notice is not practical,
the telephone company will notify the customer as soon as possible. Also, you will be advised of your
right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that
could affect the operation of the equipment. If this happens, the telephone company will provide
advance notice in order for you to make the necessary modifications in order to maintain uninterrupted
service.
If trouble is experienced with this equipment, please see the numbers in this manual for repair and (or)
warranty information. If the trouble is causing harm to the telephone network, the telephone company
may request you remove the equipment from the network until the problem is resolved.
The customer can do the following repairs: Replace any original equipment that came with the device.
This includes the print cartridge, the supports for trays and bins, the power cord, and the telephone
cord. It is recommended that the customer install an AC surge arrestor in the AC outlet to which this
device is connected. This is to avoid damage to the equipment caused by local lightning strikes and
other electrical surges.
Telephone Consumer Protection Act (US)
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or
other electronic device, including fax machines, to send any message unless such message clearly
contains, in a margin at the top or bottom of each transmitted page or on the first page of the
transmission, the date and time it is sent and an identification of the business, other entity, or individual
sending the message and the telephone number of the sending machine or such business, or other
entity, or individual. (The telephone number provided cannot be a 900 number or any other number for
which charges exceed local or long distance transmission charges).
Industry Canada CS-03 requirements
Notice: The Industry Canada label identifies certified equipment. This certification means the
equipment meets certain telecommunications network protective, operational, and safety requirements
as prescribed in the appropriate Terminal Equipment Technical Requirement document(s). The
Department does not guarantee the equipment will operate to the user’s satisfaction. Before installing
this equipment, users should ensure that it is permissible for the equipment to be connected to the
facilities of the local telecommunications company. The equipment must also be installed using an
acceptable method of connection. The customer should be aware that compliance with the above
conditions may not prevent degradation of service in some situations. Repairs to certified equipment
should be coordinated by a representative designated by the supplier. Any repairs or alterations made
by the user to this equipment, or equipment malfunctions, may give the telecommunications company
cause to request the user to disconnect the equipment. Users should ensure for their own protection that
the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe
system, if present, are connected together. This precaution can be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or electrician, as appropriate. The Ringer Equivalence
Number (REN) of this device is 0.0.
ENWW
Additional statements for telecom (fax) products
259
Notice: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication
of the maximum number of terminals allowed to be connected to a telephone interface. The termination
on an interface may consist of any combination of devices subject only to the requirement that the sum
of the Ringer Equivalence Number of all the devices does not exceed five (5.0). The standard
connecting arrangement code (telephone jack type) for equipment with direct connections to the
telephone network is CA11A.
Vietnam Telecom wired marking for ICTQC Type approved
products
260
Appendix D Regulatory information
ENWW
Index
Symbols/Numerics
2-sided printing
Windows 73
A
accessibility features 5
accessories
ordering 233, 234
part numbers 234
acoustic specifications 246
ad hoc groups, sending faxes to
131
address, printer
Macintosh, troubleshooting
230
answer mode, setting 120
answering machines, connecting
fax settings 121
anticounterfeit supplies 169
autoreduction settings, fax 123
B
background shading,
troubleshooting 219
bands and streaks,
troubleshooting 219
batteries included 250
bin, output
capacity 4
jams, clearing 209
locating 6
black and white scanning 102
blank pages
troubleshooting 227
blank scans, troubleshooting 223
blocking faxes 121
booklets
printing (Windows) 75
ENWW
busy signals, redialing options
117
C
cables
USB, troubleshooting 227
caller-ID boxes, connecting 109
calling cards 130
Canadian DOC regulations 255
canceling
copy jobs 86
faxes 127
print job 60
scan jobs 100
capacity
document feeder 4
output bin 4
cartridge-door release, locating 6
cartridges
non-HP 169
part numbers 234
recycling 169, 249
replacing 172
status, viewing 160
storage 169
warranty 237
cautions iii
change
pickup roller 175
print cartridge 172
separation pad 180
characters, troubleshooting 220
checklist
fax troubleshooting 138
general troubleshooting 198
cleaning
exterior 194
glass 91, 103, 194
paper path 189
pickup roller 182
product 182
separation pad 186
clearing jams
locations 207
collating copies 89
color, scanning settings 101, 102
comparison, product models 2
configuration page
printing 156
connecting to the network 42
connectivity
solving problems 227
contrast settings
copy 92
fax 118
control panel
buttons and lights 11, 12
menus 14
message types 203
messages, troubleshooting
203
settings 24, 30
status-light patterns 200
conventions, document iii
copying
canceling 86
collation 89
contrast, adjusting 92
double-sided 94
enlarging 86
light/dark settings 92
multiple copies 84
one-touch 84
quality, adjusting 89
quality, troubleshooting 222
reducing 86
setup menu 15
counterfeit supplies 169
Index
261
cover pages
printing (Mac) 33
creases, troubleshooting 221
crooked pages 216, 221
curled media 220
custom-size copies 86
custom-size paper settings
Mac 32
Windows 65
customer support
online 240
repacking product 241
service information form 242
D
dark copying 223
darkness, contrast settings
copy 92
fax 118
defaults, restoring 199
defects, repeating 224
delaying fax sending 134
deleting faxes from memory 127
demo page, printing 157
dial-tone detection settings 116
dialing
fax 17
from a telephone 134
manually 130
pauses, inserting 116
prefixes, inserting 116
redial manually 131
redialing automatically,
settings 117
tone or pulse settings 117
troubleshooting 149
disposal, end-of-life 250
distinctive-ring settings 122
document conventions iii
document feeder
capacity 4, 55
loading 54
locating 6
page sizes supported 148
dots per inch (dpi)
fax 119
specifications 4
dots, troubleshooting 218
262
Index
double-sided printing
Macintosh 34
paper loading orientation 55
See also duplex printing
dpi (dots per inch)
fax 119
faxing 17
scanning 101
specifications 4
drivers
changing paper types and
sizes 48
changing settings (Mac) 31
changing settings (Windows)
25
choosing (Windows) 226
Macintosh, troubleshooting
229
presets (Mac) 32
quick sets (Windows) 63
settings 24, 30
settings (Mac) 32
settings (Windows) 61
supported 24
DSL
faxing 128
duplex printing
Macintosh 34
paper loading orientation 55
Windows 73
See also double-sided printing
E
e-mail, scanning to
Mac 37, 99
resolution settings 102
EconoMode setting 167
electrical specifications 246
electronic faxes
receiving 137
sending 132
embedded Web server
Configuration page 165
HP Smart Install tab 165
Information tab 165
Networking tab 165
product status 165
Settings tab 165
shop for supplies 165
supplies status 165
support 165
using 164
end-of-life disposal 250
enlarging documents
copying 86
envelopes
loading orientation 55
environment specifications 246
environmental features 3
environmental stewardship
program 248
ePrint
AirPrint
79
HP Cloud Print 76
HP Direct Print 78
error messages
control panel 203
error messages, fax 139
error report, fax
printing 146
error-correction setting, fax 147
European Union, waste disposal
251
EWS. See embedded Web server
extension phones
receiving faxes from 110
sending faxes from 134
F
factory-set defaults, restoring 199
faded print 218
fax
ad hoc groups 131
answer mode 17, 120
autoreduction 123
blocking 121
canceling 127
contrast setting 118
delaying sending 134
deleting from memory 127
detect-dial-tone settings 116
dial prefixes 116
dialing, tone or pulse 117
error messages 139
error report, printing 146
error-correction 147
extension phone receiving
110
factory-set defaults, restoring
199
ENWW
forwarding 120
manual dialing 130
pauses, inserting 116
polling 126
printing 136
printing private faxes 136
private receive 125
receive log 162
receiving from software 137
receiving when you hear fax
tones 137
redial manually 131
redial settings 117
reports 16
reports, printing all 145
reprinting from memory 136
resolution 119
ring patterns 122
ring type 18
rings-to-answer 121
security, private receive 125
send log 162
sending from a telephone 134
sending from software 132
silence-detect mode 124
stamp-received 125
troubleshooting receiving 151
troubleshooting sending 148
using DSL, PBX, or ISDN 128
using VoIP 129
V.34 setting 148
volume settings 124
fax date, setup
use control panel 112
use HP Fax Setup Wizard 113
fax header, setup
use control panel 112
use HP Fax Setup Wizard 113
fax ports, locating 9
fax reports, printing 16
Fax tab
HP Toolbox 160
fax time, setup
use control panel 112
use HP Fax Setup Wizard 113
fax troubleshooting
checklist 138
ENWW
faxing
from a computer (Mac) 36,
132
from a computer (Windows)
132
features
product 4
feeding problems, solving 216
file, scanning to
Mac 37, 98
Finnish laser safety statement 256
first page
use different paper 33
Fit to Page setting, fax 123
forms
printing (Windows) 66
forwarding faxes 120
fraud hotline 169
G
glass, cleaning 91, 103, 194
gray background,
troubleshooting 219
grayscale printing, Windows 62
grayscale scanning 102
H
help
printing options (Windows) 61
AirPrint
79
HP Cloud Print 76
HP Customer Care 240
HP Direct Print 78
HP Embedded Web Server 27
HP fraud hotline 169
HP LaserJet Scan (Windows) 98
HP Smart Install tab (embedded
Web server) 165
HP Toolbox
about 159
Fax tab 160
Status tab 160
humidity specifications 246
I
identification cards
copying 85
image quality
copy, troubleshooting 222
scans, troubleshooting 223
Information tab (embedded Web
server) 165
input tray
capacity 55
loading 51
locating 6
interface ports
locating 8, 9
types included 4
international dialing 130
IP address
Macintosh, troubleshooting
230
manual configuration 43
ISDN
faxing 128
J
jams
common causes of 206
document feeder, clearing
208
locations 207
output-bin, clearing 209
tray, clearing 211
K
Korean EMC statement 255
L
labels
printing (Windows) 68
landscape orientation
changing (Windows) 81
laser safety statements 255, 256
LaserJet Scan (Windows) 98
letterhead
printing (Windows) 66
license, software 238
light copying 223
light patterns
control panel 200
light print, troubleshooting 218
lightness
copy contrast 92
faded print, troubleshooting
218
fax contrast 118
lines, troubleshooting
copies 222
Index
263
printed pages 219
scans 223
link speed settings 44
loading media
document feeder 54
input tray 51
lock
product 166
logs, fax
error 146
printing all 145
loose toner, troubleshooting
219
M
Mac
changing paper types and
sizes 48
driver settings 31, 32
faxing 36
faxing from 132
problems, troubleshooting 229
removing software 30
resize documents 32
scanning from TWAINcompliant software 99
scanning page-by-page 37,
98
scanning to e-mail 37, 99
scanning to file 37, 98
Mac driver settings
custom-size paper 32
Macintosh
drivers, troubleshooting 229
support 240
supported operating systems
30
USB card, troubleshooting
231
managing network 43
manual dialing 130
manual redial 131
material restrictions 250
Material Safety Data Sheet
(MSDS) 251
media
curled, troubleshooting 220
custom-size, Mac settings 32
default size for tray 56
document feeder, sizes
supported 148
264
Index
fax autoreduction settings 123
first page 33
pages per sheet 33
supported sizes 49
wrinkled 221
memory
deleting faxes 127
reprinting faxes 136
specifications 4
menu
Copy setup 15
Fax functions 14
Fax Job status 14
Fax setup 16
Phone Book 14
Reports 15
Service 20
System setup 19
menu map
printing 158
mercury-free product 250
messages
control panel 203
Microsoft Word, faxing from 133
model
comparison 2
number, locating 10
modems, connecting 109
multiple pages per sheet
printing (Windows) 79
N
n-up printing
selecting (Windows) 79
network
IP address configuration 43
link speed settings 44
operating systems supported
40
password, changing 43
password, setting 43
settings, changing 43
settings, viewing 43
network connections 42
network port
locating 9
Networking tab (embedded Web
server) 165
non-HP supplies 169
notes iii
number of copies, changing 84
number of print copies
changing (Windows) 62
O
OCR software 100
online support 240
opening printer drivers
(Windows) 61
operating environment
specifications 246
operating systems supported 24,
30
operating systems, networks 40
optical character recognition
software 100
ordering
part numbers for 234
supplies and accessories 234
ordering supplies
Web sites 233
orientation
changing (Windows) 81
paper, while loading 55
output bin
capacity 4, 55
locating 6
output quality
copy, troubleshooting 222
scans, troubleshooting 223
outside lines
dial prefixes 116
pauses, inserting 116
P
packaging product 241
page orientation
changing (Windows) 81
page sizes
scaling documents to fit
(Windows) 71
page-by-page scanning (Mac) 37,
98
pages
blank 227
not printing 227
printing slowly 227
skewed 221
pages per minute 4
ENWW
pages per sheet
selecting (Windows) 79
pages, skewed 216
paper
curled, troubleshooting 220
custom-size, Mac settings 32
document feeder, sizes
supported 148
fax autoreduction settings 123
first page 33
loading orientation 55
pages per sheet 33
printing on preprinted letterhead
or forms (Windows) 66
supported sizes 49
supported types 50
wrinkled 221
paper handling
problem-solving 216
paper input trays
feeding problems, solving 216
paper jams. See jams
paper path, cleaning 189
paper size
changing 48
changing (Windows) 65
custom (Windows) 65
paper type
changing (Windows) 66
paper types
changing 48
paper, covers
printing (Windows) 69
paper, ordering 234
paper, special
printing (Windows) 68
part numbers
print cartridges 234
pauses, inserting 116
PBX
faxing 128
phone book, fax
deleting all entries 115
HP Toolbox 160
importing 114
phones
receiving faxes from 110, 137
phones, connecting extra 110
phones, downstream
sending faxes from 134
ENWW
physical specifications 246
pickup roller
change 175
clean 182
pixels per inch (ppi), scanning
resolution 101
polling faxes 126
portrait orientation
changing (Windows) 81
ports
locating 8, 9
troubleshooting Macintosh
231
types included 4
power
consumption 246
problem-solving 198
ppi (pixels per inch), scanning
resolution 101
prefixes, dial 116
preprinted paper
printing (Windows) 66
presets (Mac) 32
print cartridges
door release, locating 6
non-HP 169
part numbers 234
recycling 169, 249
redistributing toner 170
status, viewing 160
storage 169
warranty 237
print density 225
print job
canceling 60
print media
supported 49
print-cartridges
replacing 172
printer drivers
supported 24
printer drivers (Mac)
changing settings 31
settings 32
printer drivers (Windows)
changing settings 25
choosing 226
settings 61
printing
configuration page 156
demo page 157
Macintosh 32
menu map 158
settings (Mac) 32
settings (Windows) 61
supplies status page 157
troubleshooting 227
priority, settings 24, 30
private receive 125
problem-solving
clear jams 206
connectivity 227
control-panel messages 203
image quality 218
Mac issues 229
paper handling 216
performance 227
status-light patterns 200
Windows issues 229
See also solving
product
cleaning 182
model comparison 2
serial number, locating 10
product registration 163
protocol settings, fax 148
pulse-dialing 117
Q
quality
copy settings 89
copy, troubleshooting 222
print settings (Macintosh) 32
scans, troubleshooting 223
quick sets 63
R
Readiris OCR software 100
receiving faxes
answer mode, setting 120
autoreduction settings 123
blocking 121
error report, printing 146
from extension phone 110
from software 137
log, HP Toolbox 162
polling 126
reprinting 136
ring patterns, settings 122
rings-to-answer settings 121
Index
265
silence-detect mode 124
stamp-received setting 125
troubleshooting 151
when you hear fax tones 137
recycling
HP printing supplies returns and
environmental program 249
recycling supplies 169
redial
manually 131
redialing
automatically, settings 117
redistributing toner 170
reducing documents
copying 86
registration, product 163
removing Mac software 30
repacking product 241
repeating defects,
troubleshooting 224
repetitive defects, troubleshooting
221
reports
configuration page 16, 156
demo page 15, 157
fax 16
menu map 16, 158
supplies status page 16, 157
reports, fax
error 146
printing all 145
reprinting faxes 136
resize documents
Mac 32
Windows 71
resizing documents
copying 86
resolution
changing (Windows) 66
fax 119
scanning 101
specifications 4
restoring factory-set defaults 199
ring patterns 122
ring tones
distinctive 122
rings-to-answer setting 121
ruler, repetitive defect 224
266
Index
S
safety statements 255, 256
scale documents
Mac 32
Windows 71
scaling documents
copying 86
scanner
glass cleaning 91, 103, 194
scanning
black and white 102
blank pages, troubleshooting
223
canceling 100
color 101
file formats 101
from HP LaserJet Scan
(Windows) 98
from Mac software 37
grayscale 102
methods 98
OCR software 100
page-by-page (Mac) 37, 98
quality, troubleshooting 223
resolution 101
to e-mail (Mac) 37, 99
to file (Mac) 37, 98
TWAIN-compliant software 99
WIA-compliant software 99
scatter, troubleshooting 221
sending faxes
ad hoc groups 131
canceling 127
delaying 134
error report, printing 146
forwarding 120
from downstream telephone
134
from software 132
log, HP Toolbox 162
manual dialing 130
troubleshooting 148
separation pad
change 180
clean 186
serial number, locating 10
service
information form 242
repacking product 241
Service menu 20
settings
driver presets (Mac) 32
drivers 25
drivers (Mac) 31
factory-set defaults, restoring
199
priority 24, 30
Settings tab (embedded Web
server) 165
shipping product 241
silence-detect mode 124
size specifications, product 246
size, copy
reducing or enlarging 86
sizes, media
Fit to Page setting, faxing 123
skewed pages 216, 221
slow speed, troubleshooting
faxing 150, 153
small documents
copying 85
smeared toner, troubleshooting
219
software
embedded Web server 27
Readiris OCR 100
receiving faxes 137
scanning from TWAIN or
WIA 99
sending faxes 132
settings 24, 30
software license agreement
238
supported operating systems
24, 30
uninstalling for Windows 25
uninstalling Mac 30
Windows 27
Windows components 23
solving
direct-connect problems 227
feeding problems 216
network problems 228
skewed pages 216
See also problem-solving
special media
guidelines 46
special paper
guidelines 46
printing (Windows) 68
ENWW
special paper for covers
printing (Windows) 69
specifications
electrical and acoustic 246
environment 246
physical 246
product features 4
specks, troubleshooting 218
speed
fax, troubleshooting 150, 153
print specifications 4
spots, troubleshooting 218
status
fax job 14
viewing 160
status-light patterns 200
storing
print cartridges 169
product 246
streaks, troubleshooting 219
supplies
counterfeit 169
non-HP 169
ordering 163, 233, 234
part numbers 234
recycling 169, 249
status, viewing 160
supplies status page
printing 157
support
online 163, 240
repacking product 241
service information form 242
supported media 49
System setup menu 19
T
TCP/IP
operating systems supported
40
technical support
online 240
repacking product 241
service information form 242
telephones
receiving faxes from 110, 137
telephones, connecting extra 110
telephones, downstream
sending faxes from 134
temperature specifications 246
ENWW
text, troubleshooting 220
tips iii
tone-dialing 117
toner
loose, troubleshooting 219
redistributing 170
scatter, troubleshooting 221
smeared, troubleshooting 219
specks, troubleshooting 218
toner cartridges. See print
cartridges
transparencies
printing (Windows) 68
tray
capacity 4
jams, clearing 211
trays
default media size 56
double-sided printing 34
locating 6
paper orientation 55
troubleshooting
blank pages 227
blank scans 223
control panel messages 203
copy quality 222
curled media 220
dialing 149
direct-connect problems 227
faded print 218
fax error-correction setting
147
faxes 138
lines, copies 222
lines, printed pages 219
lines, scans 223
loose toner 219
Mac problems 229
network problems 228
pages not printing 227
pages printing slowly 227
pages too dark 223
pages too light 223
receiving faxes 151
repeating defects 224
repetitive defects 221
scan quality 223
sending faxes 148
skewed pages 221
speed, faxing 150, 153
text 220
toner scatter 221
toner smear 219
toner specks 218
USB cables 227
wrinkles 221
See also solving; problemsolving
troubleshooting checklist 198
TWAIN-compliant software,
scanning from 99
two-sided printing
Windows 73
U
unblocking fax numbers 121
uninstalling Mac software 30
uninstalling Windows software 25
USB cable, part number 234
USB port
locating 8, 9
troubleshooting 227
troubleshooting Macintosh
231
type included 4
V
V.34 setting 148
vertical lines, troubleshooting 219
vertical white or faded stripes
222
VoIP
faxing 129
volume
settings 20
volume, adjusting 124
W
warnings iii
warranty
customer self repair 240
license 238
print cartridges 237
product 236
watermarks
printing (Windows) 72
wavy paper, troubleshooting 220
Web sites
customer support 240
fraud reports 169
Index
267
Macintosh customer support
240
Material Safety Data Sheet
(MSDS) 251
ordering supplies 233
white or faded stripes,
troubleshooting 222
WIA-compliant software, scanning
from 99
Windows
changing paper types and
sizes 48
driver settings 25
faxing from 132
problem-solving issues 229
scanning from TWAIN or WIA
software 99
software components 23, 27
software for 159
supported operating systems
24
Word, faxing from 133
wrinkles, troubleshooting 221
268
Index
ENWW
© 2011 Hewlett-Packard Development Company, L.P.
www.hp.com
*CE841-91012*
*CE841-91012*
CE841-91012
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement