Lenel Systems International Inc.

Lenel Systems International Inc.
Lenel Systems International Inc.
HARDWARE PRODUCTS CATALOG
PERPETUAL INNOVATION
Manage Everything...
Contents
Page
Access Control Hardware
Intelligent System Controllers
1
Intelligent Dual Reader Controller
9
Reader Interface Modules
11
Input/Output Control Modules
15
Reader Interface Gateways
19
Star Multiplexer
23
Access Control
Controllers & Interfaces
Magnetic Card Access Readers
25
Proximity Card Readers
27
™
™
33
Biometric Reader
36
Indestructible Keypads & Readers
39
Command Keypad
43
Video
OpenCard & OpenProx Readers
Power Supplies and Enclosures
Multi-Agency Power Supply/Chargers
45
CE-Marked Power Supply/Chargers
47
Identity Credential Hardware
Capture Hardware
USB Capture Kit
49
Digital Video Hardware
Video Recorders
Video Recorders for OnGuard VideoManager™
51
Network Video Cameras
Fixed Network Cameras
53
Speed Dome Network Cameras
57
Video Encoders
Single Channel Video Encoder
Contact Information
Credential
Readers & Keypads
61
64
Intelligent System Controller
LNL-500
The LNL-500 Intelligent System Controller (ISC) by Lenel serves as the access control engine for
an OnGuard system. The ISC provides power, performance, and flexibility for the most demanding
applications. Multiple combinations of Input Control Modules, Output Control Modules, and Card
Reader Interface Modules can be connected.
The ISC can communicate upstream at 38.4 Kbps via RS-232/RS-485 multidropped configuration,
modem dial-up communication, or Ethernet TCP/IP networks. The ISC can store up to 12,500
Access Control
cardholders. The ISC can have two downstream 2-wire RS-485 channels or one 4-wire RS-485
channel. In either configuration, you may connect up to 32 readers or 16 devices. Each device
(LNL-1100, LNL-1200, LNL-1300,LNL-1320) uses one device address.
Features and Functionality
■ Host communications - 38.4 Kbps direct wire (RS-232/RS-485 multidropped), Ethernet TCP/IP,
or dial-up communication
■ 12 VAC or 12 VDC input power
■ Supports up to 8 different card formats simultaneously
■ Enhanced anti-passback capabilities
■ Flash memory for real-time program updates
■ Lithium battery back-up
■ Up to 32,000 access levels
■ 255 holidays with grouping
■ 255 timezones, each with 6 time intervals
■ Elevator control, support for 64 floors
■ 512 KB on-board memory (Up to 12,500 cardholders)
■ Up to 16 downstream devices and 32 readers
■ Alarm masking
■ Individual extended held open and strike times (ADA required)
■ Up to 9-digit PIN codes
■ Biometric smart card template storage support
■ Status LEDs for heartbeat, upstream and downstream communication
■ 2 dedicated inputs for tamper and power failure status
■ NIST certified Advanced Encryption Standard (AES) 128-bit communication algorithm
1
LNL-500
OnGuard
Security
Server
Up to 16 Downstream Devices
(32 Readers Max)
LNL-1300
Up to 16 Single Reader
Interface Modules
LOCAL AREA NETWORK (TCP/IP)
LNL-500
Intelligent
System
Controller
Downstream
Communication
Two 2-wire ports or
One 4-wire port
RS-485 multidrop
Access Control
CORPORATE HEADQUARTERS
LNL-1320
Up to 16 Dual Reader
Interface Modules
LNL-1100
Input Control Module
(Up to 16 Inputs per
LNL-1100)
LNL-1200
Output Control Module
(Up to 16 Outputs per
LNL-1200)
Controller Options
LNL-500
Host Communications
LNL-ETHLAN-MICR
Dial-Up Modem
LNL-56KEXT
LNL-DC336K
Standard 512 KB on-board memory
CoBox Micro serial server, flash ROM, RJ-45 (10/100Base-T), diagnostic LEDs, dimensions 1.57 x 1.93 in. (39 x 49 mm),
internally powered, standoffs included
56 K external modem with cables
12 VDC-powered, 33.6 K external modem for Intelligent System Controller
Power Supplies & Enclosures
LNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
Lenel UL Listed 4 A, 110 VAC Power Supply - 12 VDC or 24 VDC 4 A output (switch-selectable), 120 VAC input, continuous
supply current with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch,
UPS-capable (battery optional), UL-listed
Lenel UL Listed Power Supply - 12 VDC or 24 VDC 6 A output (switch-selectable), 120 VAC (1.6 amps) input, continuous supply
current with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable
(battery optional), UL-listed
Battery Kit - 12 VDC, 12 AH battery (PS-12120)
Specifications
Primary Power (DC or AC)
DC input:
AC input:
Memory and Clock Backup
Environmental
Temperature:
Humidity:
Mechanical
Dimensions:
Weight:
Approvals
* The ISC is for use in low voltage, power-limited, class 2 circuits only.
12 VDC ± 15%. 250 mA
12 VAC ± 15%. 400 mA RMS
3 V lithium, type BR2325
Operating: 32° to 158° F ( 0° to +70° C)
Storage: -67° to 185° F (-55° to +85° C)
0 to 95% RHNC
6 x 5 x 1 in. (152 x 127 x 25 mm)
8 oz. (230 g) nominal
UL 294 and 1076-listed, CE-marked, RoHS compliant
NIST certified Advanced Encryption Standard (AES) 128-bit communication algorithm
2
Intelligent System Controller
LNL-1000
The LNL-1000 Intelligent System Controller (ISC) by Lenel serves as the access control engine for
an OnGuard system. The ISC provides power, performance, and flexibility for the most demanding
applications. Multiple combinations of Input Control Modules, Output Control Modules, and Card
Reader Interface Modules can be attached.
The ISC can communicate upstream at 38.4 Kbps via RS-232/RS-485 multidropped
configurations, modem dial-up communication, or Ethernet TCP/IP networks. The ISC can store up
to 175,000 cardholders online. Each ISC can have four downstream 2-wire RS-485 channels or
Access Control
two 4-wire RS-485 channels. In either configuration, up to 64 readers or 32 devices may be
connected to a single ISC. Each device (LNL-1100, LNL-1200, LNL-1300, or LNL-1320) uses one
device address.
Features and Functionality
■ Host communications - 38.4 Kbps direct wire (RS-232/485 multidropped), Ethernet TCP/IP,
or dial-up
■ 12 VAC or 12 VDC input power
■ Supports up to 16 different formats (8 card formats and 8 asset formats)
■ Enhanced anti-passback capabilities
■ Flash memory for real-time program updates
■ Lithium battery back-up
■ Up to 32,000 access levels
■ 255 holidays with grouping
■ 255 timezones, each with 6 time intervals
■ Elevator control, support for 64 floors
■ 1 MB on-board memory, expandable to 4 MB (up to 175,000 cardholders)
■ Up to 32 downstream devices and 64 readers
■ Alarm masking
■ Individual extended held open and strike times (ADA required)
■ Up to 9-digit PIN codes
■ Status LEDs for heartbeat, upstream and downstream communication
■ Two dedicated inputs for tamper and power failure status
■ Biometric credential-based device support
■ NIST certified Advanced Encryption Standard (AES) 128-bit communication algorithm
3
LNL-1000
OnGuard
Security
Server
Up to 32 Downstream Devices
(64 Readers Max)
LNL-1300
Up to 32 Single Reader
Interface Modules
LOCAL AREA NETWORK (TCP/IP)
LNL-1000
Intelligent
System
Controller
Downstream
Communication
Four 2-wire ports or
Two 4-wire ports or
Combination 2- and 4-wire ports
RS-485 multidrop
Access Control
CORPORATE HEADQUARTERS
LNL-1320
Up to 32 Dual Reader
Interface Modules
LNL-1100
Input Control Module
(Up to 16 Inputs per
LNL-1100)
LNL-1200
Output Control Module
(Up to 16 Outputs per
LNL-1200)
Controller Options
LNL-1000
Memory Options
LNL-1003MK
Host Communications
LNL-ETHLAN
Dial-Up Modem
LNL-56KEXT
LNL-DC336K
Standard 1 MB on-board memory
3 MB memory expansion kit (Includes 3 MB memory and expansion board)
Micro serial server, flash ROM, DB25 serial port RJ-45 (10/100Base-T)
Ethernet interface, diagnostic LEDs, external power 120 VAC with cables
56 K external modem with cables
12 VDC-powered/33.6 K external modem for Intelligent System Controller
Specifications
Primary Power (DC or AC)
DC input:
AC input:
Memory and Clock Backup
Communication Ports
Port 1:
Ports 2-5:
Inputs
Cabinet Tamper Monitor:
Power Fault Monitor:
Wire Requirements
Power:
RS-485:
RS-232:
Inputs:
Environmental
Temperature:
Humidity:
Mechanical
Dimensions:
Weight:
Approvals
* The ISC is for use in low voltage, power-limited, class 2 circuits only.
12 VDC ± 15%. 350 mA
12 VAC ± 15%. 600 mA RMS
3 V lithium, type BR2325
RS-232 or RS-485 (2-wire or 4-wire) 9600 to 38.4 Kbps async
RS-485 (2-wire or 4-wire) 9600 to 38.4 Kbps async
Unsupervised, dedicated
Unsupervised, dedicated
1 twisted pair, 18 AWG
24 AWG twisted pair(s) with shield, 4000 ft. (1219 m) maximum
24 AWG, 25 ft. (7.6 m) maximum
Twisted pair, 30 ohms maximum
Operating: 32° to 158° F (0° to +70° C) Storage: -67° to 185° F (-55° to +85° C)
0 to 95% RHNC
6 x 8 x 1 in. (152 x 203 x 25 mm)
10 oz. (290 g) nominal
UL 294 and 1076-listed, CE-marked, RoHS compliant
NIST certified Advanced Encryption Standard (AES) 128-bit communication algorithm
4
Intelligent System Controller
LNL-2000
The LNL-2000 Intelligent System Controller (ISC) from Lenel is designed for advanced access
control applications. As the access control engine for the OnGuard system, the ISC provides
power and functionality. The ISC can communicate to the host computer in a single- or dual-path
configuration of Ethernet, dial-up or direct connect communication (RS-232/RS-485 combinations).
Multiple combinations of Input Control Modules, Output Control Modules, Biometric Gateways, and
Card Reader Interface Modules (up to 32 devices, 64 readers) can be configured.
Access Control
The LNL-2000 can communicate upstream to the host computer at up to 115.2 Kbps via RS-232,
RS-485 multidropped, dial-up, or Ethernet communication. The LNL-2000 can store up to 350,000
cardholders online, and supports selective download for larger cardholder databases. The ISC has
two host communication ports. It also has four downstream communication ports, which support
either four 2-wire or two 4-wire RS-485 communication. In either configuration, you may connect
up to 32 devices in many combinations of LNL-1100, LNL-1200,LNL-1300, LNL-1320, LNL-500B,
and LNL-500W modules.
Features and Functionality
■ Host dual path communication enabled - direct wire (RS-232/RS-485 multi-dropped), Ethernet
TCP/IP, or dial-up communications
■ 1 MB on board memory expandable to 8 MB (up to 350,000 cardholders)
■ 12 VAC or 12 VDC input power
■ Supports up to 16 different formats (8 card formats and 8 asset formats)
■ Biometric template storage support for RSI®, Identix®, and Bioscrypt®
■ Enhanced anti-passback capabilities
■ Flash memory for real-time program updates
■ Lithium battery back-up for event memory
■ Up to 32,000 access level permissions
■ 255 holidays with grouping
■ 255 timezones, each with 6 intervals
■ Elevator control support for up to 128 floors
■ Alarm masking
■ Individual extended held open and strike times (ADA required)
■ Up to 9-digit user PIN codes
■ Status LEDs for heartbeat, upstream and downstream communication
■ Two dedicated inputs for tamper and power failure status
■ NIST Certified Advanced Encryption Standard (AES) 128-bit algorithm for communications
5
LNL-2000
OnGuard
Security
Server
Up to 8 Biometric Devices
LNL-1300
LNL-500B
Up to 32 Downstream Devices
(64 Readers Max)
LOCAL AREA NETWORK (TCP/IP)
LNL-2000
Intelligent
System
Controller
LNL-1300
Up to 32 Single Reader
Interface Modules
RS-485 multidrop
Downstream
Communication
Four 2-wire ports
Two 4-wire ports
Combination 2- and 4-wire ports
LNL-1320
Up to 32 Dual Reader
Interface Modules
LNL-1100
Input Control Module
(Up to 16 Inputs per
LNL-1100)
Access Control
CORPORATE HEADQUARTERS
LNL-1200
Output Control Module
(Up to 16 Outputs per
LNL-1200)
Hand Geometry or Fingerprint
Readers
Readers
Controller Options
LNL-2000
Memory Options
LNL-1003MK
LNL-1007MK
Host Communications
LNL-ETHLAN
LNL-ETHLAN-MICR
Dial-Up Modem
LNL-56KEXT
LNL-DC336K
Standard 1 MB on-board memory
3 MB memory expansion kit (Includes 3 MB memory and expansion board)
7 MB memory expansion kit (Includes 7 MB memory and expansion board)
Micro serial server, flash ROM, DB25 serial port RJ-45 (10/100Base-T)
CoBox Micro serial server, flash ROM, RJ-45 (10/100Base-T), diagnostic LEDs,
dimensions 1.6 x 1.9 in. (40 x 49 mm), internally powered and includes standoffs
56 K external Modem with cables
12 VDC-powered/33.6 K external modem for Intelligent System Controller
Specifications
Primary Power (DC or AC)
DC input:
AC input:
Memory and Clock Backup
Communication Ports
Port 1, 6:
Ports 2-5:
Inputs
Cabinet Tamper Monitor:
Power Fault Monitor:
Wire Requirements
Power:
RS-485:
RS-232:
Inputs:
Environmental
Temperature:
Humidity:
Mechanical
Dimensions:
Weight:
Approvals
* The ISC is for use in low voltage, power-limited, class 2 circuits only.
12 VDC ± 15%. 400 mA
12 VAC ± 15%. 650 mA RMS
3 V lithium, type BR2325
RS-232 or RS-485 (2-wire or 4-wire) 9600 to 115.2 Kbps async
RS-485 (2-wire or 4-wire) 9600 to 38.4K bps async
Unsupervised, dedicated
Unsupervised, dedicated
1 twisted pair, 18 AWG
24 AWG twisted pair(s) with shield, 4000 ft. (1219 m) maximum
24 AWG, 25 ft. (7.6 m) maximum
Twisted pair, 30 ohms maximum
Operating: 32° to 158° F (0° to +70° C)
Storage: -67° to 185° F (-55° to +85° C)
0 to 95% RHNC
6 x 8 x 1 in. (152 x 203 x 25 mm)
10 oz. (290 g) nominal
UL 294 and 1076-listed, CE-marked, RoHS compliant
NIST certified Advanced Encryption Standard (AES) 128-bit communication algorithm
6
Intelligent System Controller
LNL-3300
The LNL-3300 Intelligent System Controller (ISC) by Lenel is designed for advanced access
control applications. As the access control engine for the OnGuard system, the ISC provides
power and functionality. The ISC can communicate to the host computer in a single- or dual-path
configuration of Ethernet, dial-up or direct connect RS-485 communication. Multiple combinations
of Input Control Modules, Output Control Modules and Card Reader Interface Modules (up to 64
devices) can be configured.
Access Control
Utilizing its native Ethernet communications and an advanced 32-bit processor, the LNL-3300 can
communicate upstream to the host computer through its primary Ethernet port, with throughput up
to 8 times greater than the fastest serial connections. The secondary port can communicate at up
to 115.2 Kbps using 2-wire RS-485 multidrop, dial-up, or an Ethernet daughterboard connection.
The LNL-3300 can store up to 500,000 cardholders in non-volatile flash memory, and supports
selective download for larger cardholder databases. The two downstream RS-485 2-wire ports
can be used to connect up to 64 devices (64 doors) in many combinations of LNL-1100, LNL-1200,
LNL-1300, LNL-1320, LNL-500B, and LNL-500W modules.
Features and Functionality
■ On-board high-speed Ethernet 10/100Base-T upstream port provides up to 8 times higher
throughput than serial-to-Ethernet converters. DHCP and fixed IP addressing supported.
■ DNS device naming through DHCP extended commands
■ Host dual path communication enabled - on-board Ethernet TCP/IP, direct wire (RS-485, 2-wire
multidrop capable), or dial-up communications
■ 15 MB of available on-board, non-volatile flash memory
■ Battery-backed, non-volatile storage of 50,000 events
■ Firmware stored in flash memory, background download of firmware updates supported
■ 12 or 24 VDC input power
■ Supports up to 16 different formats (8 card formats and 8 asset formats)
■ Biometric template storage support for Schlage Recognition Systems®, Bioscrypt®,and Identix®
■ Enhanced anti-passback capabilities
■ Up to 32,000 access level permissions
■ 255 holidays with grouping
■ 255 timezones, each with 6 intervals
■ Elevator control support for up to 128 floors
■ Alarm masking
■ Individual extended held open and strike times (ADA required)
■ Up to 9-digit user PIN codes
■ Status LEDs for heartbeat & battery status, upstream and downstream communication, and
memory write status
■ Two dedicated inputs for tamper and power failure status
■ Advanced Encryption Standard (AES) 128-bit algorithm for communications
7
LNL-3300
OnGuard
Security
Server
CORPORATE HEADQUARTERS
RS-485 multidrop
LNL-1320
Up to 16 Dual Reader
Interface Modules
LNL-1300
Up to 16 Single Reader
Interface Modules
LNL-1100
Input Control Module
(Up to 16 Inputs per
LNL-1100)
Access Control
LNL-3300
Intelligent
System
Controller
LOCAL AREA NETWORK (TCP/IP)
LNL-1200
Output Control Module
(Up to 16 Outputs per
LNL-1200)
Controller Options
LNL-3300
Secondary Host Communications
LNL-ETHLAN
LNL-ETHLAN-MICR
Dial-Up Modem
LNL-56KEXT
LNL-DC336K
15 MB On-board flash memory available for cardholder & asset database
50,000 event battery backed RAM for event log
Micro serial server, flash ROM, DB25 serial port RJ-45 (10/100Base-T)
CoBox Micro serial server, flash ROM, RJ-45 (10/100Base-T), diagnostic LEDs,
dimensions 1.6 x 1.9 in. (40 x 49 mm), internally powered and includes standoffs
56 K external modem with cables
12 VDC-powered/33.6 K external modem for Intelligent System Controller
Specifications
Primary Power (DC or AC)
DC input:
Memory and Clock Backup
Communication Ports
Primary (Ethernet) Port 0:
Secondary Upstream Port 1:
Downstream Ports 2-3:
Inputs
Cabinet Tamper Monitor:
Power Fault Monitor:
Wire Requirements
Power:
RS-485:
RS-232:
Inputs:
Environmental
Temperature:
Humidity:
Mechanical
Dimensions:
Weight:
Approvals
* The ISC is for use in low voltage, power-limited, class 2 circuits only.
12 or 24 VDC ± 15%. 300 mA maximum
3 V lithium, type BR2325, BR2330, CR2330
10/100Base-T Ethernet high-speed port
RS-485 (2-wire) or RS-232 9600 to 115.2 Kbps async, optional Ethernet serial server
RS-485 (2-wire) 9600 to 38.4 Kbps async
Unsupervised, dedicated
Unsupervised, dedicated
1 twisted pair, 18 AWG
24 AWG twisted pair(s) with shield, 4000 ft. (1219 m) maximum
24 AWG, 25 ft. (7.6 m) maximum
Twisted pair, 30 ohms maximum
Operating: 32° to 158° F (0° to +70° C)
Storage: -67° to 185° F (-55° to +85° C)
0 to 95% RHNC
5 x 6 x 1 in. (127 x 152.4 x 25 mm)
4 oz. (115 g) nominal
UL 294 and 1076-listed, CE-marked, ROHS compliant
Advanced Encryption Standard (AES) 128-bit communication algorithm, NIST certification pending
8
Intelligent Dual Reader Controller
LNL-2220
The LNL-2220 Intelligent Dual Reader Controller (IDRC) by Lenel provides a single board solution
for interfacing one or two doors to an OnGuard system. In addition, other I/O and reader interface
modules can be added on the LNL-2220’s downstream port to expand its capabilities. The
LNL-2220 revolutionizes access control system architecture by allowing Ethernet connection
directly from an entry location to the OnGuard server, while still providing the security, functionality,
and modularity of Lenel’s proven hardware platform. The LNL-2220 is scalable for any access
control application, from the most basic to the most sophisticated. In the event of communication
loss, the LNL-2220 allows nearly all local functionality to continue unimpaired until the server
connection is restored.
Access Control
Utilizing its native Ethernet communications and an advanced 32-bit processor, the LNL-2220 can
communicate upstream to the host computer through its Ethernet port (with a throughput up to
eight times greater than the fastest serial connections), or at up to 115.2 Kbps using RS-232
communication directly or through an external dial-up modem. The LNL-2220 can store up to
250,000 cardholders in non-volatile flash memory, and supports selective download for larger
cardholder databases. The downstream RS-485 two-wire port can be used to connect up to 32
devices (maximum 64 doors).
Two on-board reader ports support Data1/Data0, Clock/Data, Bioscrypt RS-485 readers and the
bidirectional RS-485 Open Supervised Device Protocol (OSDP) communications. Each LNL-2220
supports up to eight different card formats. The LNL-2220 includes eight inputs that support
normally open, normally closed, supervised, and unsupervised circuits. In addition, four output
relays support fail-safe or fail-secure operation.
Features and Functionality
Controller Functionality
■ On-board Ethernet 10/100Base-T port provides up to 8 times greater throughput than
serial-to-Ethernet converters. DHCP and fixed IP addressing supported.
■ DNS device naming through DHCP extended commands
■ 6 MB of available on-board, non-volatile flash memory
■ Battery-backed, non-volatile storage of 50,000 events
■ Firmware stored in flash memory, background download of firmware updates supported
■ Supports up to 16 different formats (8 card formats and 8 asset formats)
■ Biometric template storage support for Schlage Recognition Systems®, Bioscrypt®, and Identix®.
■ Direct connection of Bioscrypt RS-485 devices
■ Enhanced anti-passback capabilities
■ Up to 32,000 access level permissions
■ 255 holidays with grouping, 255 timezones, each with 6 intervals
■ Elevator control support for up to 128 floors
■ Individual extended held open and strike times (ADA required)
■ Up to 9-digit user PIN codes
■ 20 status LEDs
■ 2 dedicated inputs for tamper and power failure status
■ 12 or 24 VDC input power
■ Advanced Encryption Standard (AES) 128-bit algorithm for communications
Reader Interface Functionality
■ Supports Data1/Data0, Clock/Data and Lenel OSDP-compatible RS-485 readers and keypads
■ 4 Form-C relay outputs, 5 A at 30 VDC
■ Door contact supervision (open/closed) and REX push-button monitor for each door
■ Strike control and auxiliary output for each door
■ Bicolor reader status LED support plus beeper control, or 2-wire LED support
■ On-board regulator allows 12 VDC reader power from 24 VDC power source
9
LNL-2220
OnGuard
Security
Server
CORPORATE HEADQUARTERS
RS-485 multidrop
LNL-1300
Up to 32 Single Reader
Interface Modules
LNL-1100
Input Control Module
(Up to 16 Inputs per
LNL-1100)
LNL-1200
Output Control Module
(Up to 16 Outputs per
LNL-1200)
Access Control
LNL-2220
Intelligent
System
Controller
LOCAL AREA NETWORK (TCP/IP)
Controller Options
LNL-2220
Dial-Up Modem
LNL-56KEXT
LNL-DC336K
6 MB On-board flash memory available for cardholder & asset database,
50,000 event battery backed RAM for event log
56 K external modem with cables
12 VDC-powered/33.6 K external modem
Specifications
Primary Power (DC or AC)
DC input:
Event Memory and Clock Backup
Communication Ports
Primary (Ethernet) Port:
Alternate Upstream Port 1:
Downstream Port 2:
Inputs
Tamper and Power Fail Monitors:
Door position, REX, and AUX:
Outputs
Relay outputs:
Reader Power
DC output:
Reader Port Compatibility
Environmental
Temperature:
Humidity:
Mechanical
Dimensions:
Weight:
Approvals
* The LNL-2220 is for use in low voltage, power-limited, class 2 circuits only.
12 or 24 VDC ± 15%. 500 mA maximum
3 V lithium, type BR2325, BR2330, CR2330
10/100Base-T Ethernet high-speed port
RS-232 9600 to 115.2 Kbps async
RS-485 (2-wire) 9600 to 38.4 Kbps async
Unsupervised, dedicated
8, each programmable as normally open or normally closed, supervised or unsupervised circuits
4 Form-C 5 A at 30 VDC relay outputs: 2 strike, 2 auxiliary
12 VDC, 125 mA regulated when 24 VDC powered, or 12 to 24 VDC 125 mA current limited
Wiegand Data1/Data0, Magnetic Clock/Data, F/2F single-wire protocol, Bioscrypt RS-485,
OSDP (Open Supervised Device Protocol RS-485)
Operating: 32° to 158° F (0° to 70° C)
Storage: -67° to 185° F (-55° to 85° C)
0 to 95% RHNC
6 x 8 x 1 in. (152 x 203 x 25 mm)
9 oz. (255 g) nominal
UL 294 and 1076-listed, CE-marked, ROHS compliant
Advanced Encryption Standard (AES) 128-bit communication algorithm, NIST certification pending
10
Single Reader Interface Module
LNL-1300 Series 2
Lenel Systems International offers a Single Reader Interface (SRI) module for access control
solutions. Access control card readers, keypads, or readers with keypads that use standard
Wiegand Data1/Data0 or Clock/Data communication are supported, as are those supporting the
bidirectional RS-485 Open Supervised Device Protocol (OSDP). Lock, unlock, and facility code
offline access modes are supported on all readers connected to the SRI. Each SRI supports up to
eight different card formats as well as issue codes for both magnetic and Wiegand card formats.
Access Control
The SRI provides a vital link between the Intelligent System Controller (ISC) and the card reader
attached to the interface. As many as 32 SRI modules can be multidropped using RS-485 2-wire
communication up to 4,000 feet (1219 m) per port away from the ISC. Each SRI module is
individually addressed for increased reporting capabilities with OnGuard access control software
applications. The SRI includes two inputs that support normally open, normally closed, supervised,
and non-supervised circuits. Two output relays support fail-safe or fail-secure operation.
Features and Functionality
■ 12 or 24 VDC power supply
■ Supports Data1/Data0, Clock/Data and Lenel OSDP-compatible RS-485 readers and keypads
■ Two Form-C relay outputs (5 A door strike and 1 A aux relays)
■ Up to 16 different card formats (8 card formats and 8 asset formats)
■ Issue code support
■ Downloadable firmware
■ Door contact open or closed, supervised or non-supervised
■ REX push-button monitor - supervised or non-supervised
■ Strike control output
■ Bicolor or 2-wire reader status LED support
■ Reader beeper control
■ Plastic mounting channel
■ Support for offline reader access mode
■ Elevator control, support for 64 floors
11
LNL-1300 Series 2
OnGuard
Security
Server
CORPORATE HEADQUARTERS
LOCAL AREA NETWORK (TCP/IP)
Intelligent
System
Controller
LNL-1300
Single Reader
Interface Module
LNL-1320
Dual Reader
Interface Module
LNL-1100
Input Control Module
(Up to 16 Inputs per
LNL-1100)
LNL-1200
Output Control Module
(Up to 16 Outputs per
LNL-1200)
Access Control
RS-485 multidrop
Power Supplies & Enclosures
LNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
Lenel UL-listed 4 A, 110 VAC power supply - 12 or 24 VDC 4 A output (switch-selectable), 120 VAC input, continuous supply current
with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS capable (battery
optional), UL-listed
Lenel UL listed power supply - 12 or 24 VDC 6 A output (switch-selectable), 120 VAC (1.6 amps) input, continuous supply current
with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS capable (battery
optional), UL-listed
Battery kit - 12 VDC, 12 AH battery (PS-12120)
Specifications
Primary Power (DC)
DC input:
Reader Power
DC output:
Reader Port Compatibility
Environmental
Temperature:
Humidity:
Mechanical
Dimension:
Weight:
Approvals
* The SRI is for use in low voltage, power-limited, class 2 circuits only.
12 or 24 VDC ± 15%. 125 mA
12 VDC 125 mA max current limited
Wiegand Data1/Data0
Magnetic Clock/Data
F/2F single-wire protocol
Open Supervised Device Protocol (RS-485)
Operating: 32° to 158° F (0° to +70° C)
Storage: -67° to 185° F (-55° to +85° C)
0 to 95% RHNC
2.9 x 4.25 x 1.4 in. (74 x 108 x 36 mm)
4 oz. (120 g) nominal
UL 294 and 1076-listed, CE-marked, RoHS compliant
12
Dual Reader Interface Module
LNL-1320 Series 2
Lenel Systems International offers a Dual Reader Interface (DRI) module for access control
solutions. Most access control card readers, keypads, or readers with keypads that use standard
Wiegand Data1/Data0 or Clock/Data communication are supported, as are those that support the
bidirectional RS-485 Open Supervised Device Protocol (OSDP). Lock, unlock, and facility code
offline access modes are supported on all readers connected to the DRI. Each DRI supports up to
eight different card formats as well as issue codes for both magnetic and Wiegand card formats.
Access Control
The DRI provides a vital link between the Intelligent System Controller (ISC) and the card reader
attached to the interface. As many as 32 DRI modules can be multidropped using RS-485 2-wire
or 4-wire communication up to 4,000 feet per port away from the ISC. Each DRI module is
individually addressed for increased reporting capabilities with OnGuard access control software
applications. The DRI includes eight inputs that support normally open, normally closed,
supervised, and non-supervised circuits. In addition, six output relays support fail-safe or
fail-secure operation.
Features and Functionality
■ 12 or 24 VDC power supply
■ Supports Data1/Data0, Clock/Data and Lenel OSDP-compatible RS-485 readers and keypads
■ Downloadable firmware
■ Six Form-C 5 A at 30 VDC relay outputs
■ Up to 16 different formats (8 card formats and 8 asset formats)
■ Issue code support for magnetic and Wiegand formats
■ Door contact supervision (open/closed)
■ REX push-button monitor
■ Strike control output
■ Bicolor reader status LED support and 2-wire LED support
■ Beeper control
■ Dedicated tamper and power failure circuits
■ Support for offline reader access mode
■ On-board jumpers for termination
■ On-board regulator allows 12 VDC reader support from 24 VDC power source
■ DIP switch-selectable addressing
13
LNL-1320 Series 2
OnGuard
Security
Server
CORPORATE HEADQUARTERS
LOCAL AREA NETWORK (TCP/IP)
Intelligent
System
Controller
LNL-1300
Single Reader
Interface Module
LNL-1320
Dual Reader
Interface Module
LNL-1100
Input Control Module
(Up to 16 Inputs per
LNL-1100)
LNL-1200
Output Control Module
(Up to 16 Outputs per
LNL-1200)
Access Control
RS-485 multidrop
Power Supplies & Enclosures
LNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
Lenel UL-listed 4 A, 110 VAC power supply - 12 or 24 VDC 4 A output (switch-selectable), 120 VAC input, continuous supply current
with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery
optional), UL-listed
Lenel UL Listed Power Supply - 12 or 24 VDC 6 A output (switch-selectable), 120 VAC (1.6 amps) input, continuous supply current
with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery
optional), UL-listed
Battery kit - 12 VDC, 12 AH battery (PS-12120)
Specifications
Primary Power (DC)
DC input:
Reader Power
DC output:
Reader Port Compatibility
Environmental
Temperature:
Humidity:
Mechanical
Dimension:
Weight:
Approvals
* The DRI is for use in low voltage, power-limited, class 2 circuits only.
12 or 24 VDC ± 15%. 450 mA
12 VDC, 125 mA regulated or 12 to 24 VDC 125 mA current limited
Wiegand Data1/Data0
Magnetic Clock/Data
F/2F single-wire protocol
Open Supervised Device Protocol (RS-485)
Operating: 0° to +70° C (32° to 158° F)
Storage: -55° to +85° C (-67° to 185° F)
0 to 95% RHNC
6 x 8 x 1 in. (152 x 203 x 25 mm)
10 oz. (290 g) nominal
UL 294 and 1076-listed, CE-marked, ROHS compliant
14
Input Control Module
LNL-1100 Series 2
The Lenel Input Control Module (ICM) provides the access control system with high-speed
acknowledgment of critical alarm points in monitored areas. The ICM communicates directly with
the Intelligent System Controller (ISC) either by 2-wire or 4-wire RS-485 communication. The ICM
has 16 configurable input control points and 2 output control relays. It supports normally open,
normally closed, supervised and non-supervised circuits.
The input circuits are scanned using an analog-to-digital converter. The digitized input status
Access Control
signal is software-monitored and controlled, so that each input point can be programmed as a
supervised or non-supervised alarm point.
The output relays can also be configured for fail-safe or fail-secure operation. Each relay supports
the “On,” “Off,” and “Pulse” Lenel OnGuard software commands.
Features and Functionality
■ Grade B, A, and AA line supervision
■ 12 or 24 VDC input power
■ 16 programmable supervised or non-supervised contacts
■ 2 Form-C 5 A, 30 VDC contacts for load switching
■ 2 dedicated inputs for tamper and power failure status
■ On-board termination jumpers
■ DIP switch-selectable addressing
■ Elevator control, support for 64 floors
■ Status LED for host communication and heartbeat
■ Variable resistor values for line supervision
■ Downloadable firmware
15
LNL-1100 Series 2
OnGuard
Security
Server
CORPORATE HEADQUARTERS
LOCAL AREA NETWORK (TCP/IP)
Intelligent
System
Controller
LNL-1300
Single Reader
Interface Module
LNL-1320
Dual Reader
Interface Module
LNL-1100
Input Control Module
(Up to 16 Inputs per
LNL-1100)
LNL-1200
Output Control Module
(Up to 16 Outputs per
LNL-1200)
Access Control
RS-485 multidrop
Power Supplies & Enclosures
LNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
Lenel UL-listed 4 A, 110 VAC power supply - 12 or 24 VDC 4 A output (switch-selectable), 120 VAC input, continuous supply
current with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable
(battery optional), UL-listed
Lenel UL-listed power supply - 12 or 24 VDC 6 A output (switch-selectable), 120 VAC (1.6 A) input, continuous supply current with
enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery
optional), UL-listed
Battery Kit - 12 VDC, 12 AH battery (PS-12120)
Specifications
Primary Power (DC)
DC input:
Memory and Clock Backup
Environmental
Temperature:
Humidity:
Mechanical
Dimension:
Weight:
Approvals
* The ICM is for use in low voltage, power-limited, class 2 circuits only.
12 or 24 VDC ± 15%. 350 mA
3 V lithium, type BR2325
Operating: 0° to +70° C (32° to 158° F)
Storage: -55° to +85° C (-67° to 185° F)
0 to 95% RHNC
6 x 8 x 1 in. (152 x 203 x 25 mm)
10 oz. (290 g) nominal
UL 294 and 1076-listed, CE-marked, ROHS compliant
16
Output Control Module
LNL-1200 Series 2
The Lenel Output Control Module (OCM) communicates directly with the Intelligent System
Controller (ISC) by either 2-wire or 4-wire RS-485 communication. Each OCM is an
individually-addressed device, and counts as a single device on all Intelligent System Controllers.
The OCM can be operated by either 12 or 24 VDC power. Each OCM includes dedicated tamper
and power failure input contacts.
The OCM has 16 programmable output relays that can be configured for fail-safe or fail-secure
Access Control
operation. Each relay supports the “On,” “Off,” and “Pulse” Lenel OnGuard software commands.
Features and Functionality
■ 16 Form-C 5 A, 30 VDC contacts for load switching
■ 12 or 24 VDC input power
■ 2 dedicated digital inputs for tamper and power failure status
■ RS-485 communication, multidropped (2-wire or 4-wire RS-485)
■ Up to 16 OCMs per Intelligent System Controller
■ On-board termination jumpers
■ DIP switch-selectable addressing
■ Status LEDs for communication to the host, heartbeat and relay status
■ Elevator control, support for 64 floors
17
LNL-1200 Series 2
OnGuard
Security
Server
CORPORATE HEADQUARTERS
LOCAL AREA NETWORK (TCP/IP)
Intelligent
System
Controller
LNL-1300
Single Reader
Interface Module
LNL-1320
Dual Reader
Interface Module
LNL-1100
Input Control Module
(Up to 16 Inputs per
LNL-1100)
LNL-1200
Output Control Module
(Up to 16 Outputs per
LNL-1200)
Access Control
RS-485 multidrop
Power Supplies & Enclosures
LNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
Lenel UL-listed 4 A, 110 VAC power supply - 12 or 24 VDC 4 A output (switch-selectable), 120 VAC input, continuous supply current with
enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional),
UL-listed
Lenel UL-listed power supply - 12 VDC or 24 VDC 6 A output (switch-selectable), 120 VAC (1.6 amps) input, continuous supply current
with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable (battery optional),
UL-listed
Battery kit - 12 VDC, 12 AH battery (PS-12120)
Specifications
Primary Power (DC)
DC input:
Environmental
Temperature:
Humidity:
Mechanical
Dimension:
Weight:
Approvals
* The OCM is for use in low voltage, power-limited, class 2 circuits only.
12 or 24 VDC ± 15%. 500 mA
Operating: 32° to 158° F (0° to +70° C)
Storage: -67° to 185° F (-55° to +85° C)
0 to 95% RHNC
6 x 8 x 1 in. (152 x 203 x 25 mm)
16 oz. (454 g) nominal
UL 294 and 1076-listed, CE-marked, ROHS compliant
18
Biometric Reader Interface Gateway
LNL-500B
The Lenel Biometric Reader Interface Gateway (BRI) is an extremely versatile and vital link
between the Lenel LNL-2000 or LNL-3300 Intelligent System Controllers (ISCs) and biometric
readers from multiple manufacturers. Using OnGuard Access, the gateway can be uniquely
configured to support Recognition Systems hand geometry readers, Identix fingerprint readers or
Bioscrypt fingerprint readers.
The BRI communicates at 38.4Kbps via RS-485 multidropped configuration to the ISC. The
Access Control
gateway has two downstream RS-485 2-wire ports, each of which supports up to 4 uniquely
addressed biometric readers. Each downstream port supports biometric readers located up to
4,000 feet (1219 m) away from the BRI.
Features and Functionality
■ Host and downstream communications - 38.4 Kbps, 2-wire RS-485 multidropped
communications
■ 12 VDC or 12 VAC input power @ 250 mA or 400 mA
■ Supports up to 8 biometric readers
■ Supported biometric readers:
• Ingersoll Rand® - HandKey II, ID3D and HandKey CR
• Identix® V20
• Bioscrypt® V-FLEX, V-PASS-FX and V-STATION
• Lenel LNL-BIO007-xxx
■ Flash memory for real time program updates
■ Status LEDs for heartbeat, upstream and downstream communications
■ Two dedicated inputs for Cabinet Tamper and Power Failure status
■ On-board RS-485 termination jumpers
■ Easy to configure dip switches for address and communications speeds
■ Supports fingerprint and PIN code two-factor authentication
■ On-board program configuration and clock battery backup
19
LNL-500B
LAN/WAN
RS-232, RS-485, Ethernet,
Dial-up Communication
Intelligent System Controller
(64 readers maximum)
RS-232
Communication
Ports 2 - 5
One LNL-500B per port
RS-485 Communication
LNL-1320
Up to 32 Dual Reader
Interface Modules
LNL-1300
Up to 32 Single Reader
Interface Modules
LNL-500B
Ports
3
Software Link(s)
Between Readers
2
Eight Readers Per
Biometric Gateway
(address 00-07)
Software Link(s)
Between Readers
Any supported
access reader
Access Control
Enrollment Kit
Any supported
access reader
Interface Options
LNL-500B
Lenel Biometric Reader Interface Gateway - 12 VDC or 12 VAC, (5 year lithium battery) 512KB standard memory, support for a
maximum of 8 IR Hand Geometry readers per interface
Power Supplies & Enclosures
LNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
Lenel UL Listed 4 A, 110 VAC Power Supply - 12 VDC or 24 VDC 4 A output (switch selectable), 120 VAC input, continuous supply
current with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable
(battery optional), UL-listed
Lenel UL Listed Power Supply - 12 VDC or 24 VDC 6 A output (switch selectable), 120 VAC (1.6 amps) input, continuous supply
current with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable
(battery optional), UL-listed
Battery Kit - 12 VDC, 12 AH battery (PS-12120)
Specifications
Primary Power (DC or AC)
DC input:
AC input:
Memory and Clock backup
Environmental
Temperature:
Humidity:
Mechanical
Dimensions:
Weight:
Approvals
Supported Readers
* The LNL-500B is for use in low voltage, power limited, class 2 circuits only.
12 VDC ± 15%. 250 mA
12 VAC ± 15%. 400 mA RMS
3 V lithium, type BR2325
Operating: 32° to 158° F (0° to +70° C)
Storage: -67° to 185° F (-55° to +85° C)
0 to 95% RHNC
6 x 5 x 1 in. (152 x 127 x 25 mm)
8 oz. (230 g) nominal
UL 294 and 1076-listed, CE-marked, RoHS compliant
Ingersoll Rand - HandKey, HandKey II, HandKey CR and ID3D readers (Firmware version 1.21 or later required)
Identix V20 Readers (Firmware version 2.12 or later required)
Bioscrypt V-FLEX and V-STATION (Firmware version 7.30 or later required)
Lenel BioGuard Readers (LNL-BIO007-xxx)
20
Wireless Reader Interface Gateway
LNL-500W
The Lenel Wireless Reader Interface (WRI) Gateway module provides an innovative solution to
interface with Wireless products from Schlage. The gateway provides the link from the Lenel
Intelligent System Controller (ISC) to the Panel Interface Module (PIM-485-OTD) wireless receiver.
This configuration will support up to 16 Schlage wireless reader products per gateway.
The PIM-485-OTD operates in the 900 MHz license-free band, allowing rapid, no-hassle
deployment. Installation time for a standard secured entry point that requires a door contact,
Access Control
Request to Exit switch, reader and door strike is reduced by as much as 40%. The 900 MHz
spread spectrum delivery model has been extensively tested to ensure that communications are
ultra-reliable. Using this wireless configuration, communicating between OnGuard and the
Schlage wireless readers is both simple and dependable.
The gateway can communicate at 38.4Kbps via RS-485 multidropped configuration to the ISC.
The gateway has two downstream RS-485 2 wire ports. Port 3 supports one PIM-485-OTD
receiver, which in turn supports up to 16 uniquely addressed Schlage Wireless reader products.
The gateway can be installed up to 4000 feet (1219 m) away from the PIM-485-OTD. This
configuration is supported for all ISCs: LNL-500, LNL-1000 and LNL-2000.
Features and Functionality
■ Host and downstream communications - 38.4 Kbps, 2 wire RS-485 multidropped
communications
■ 12 VDC or 12 VAC input power @ 250 mA or 400 mA
■ Supports up to 16 Schlage Wireless readers
■ Supported Schlage Wireless readers include:
• WA 5296 Wireless Cylindrical Lock
• WA 5696 Wireless Mortise Lock
• WA 5694 Wireless Mortise Lock with 1” Autobolt
• WA 993 Wireless Exit Kit
• WRI (Wireless Reader Interface)
• WPR (Wireless Portable Reader)
■ Flash memory for real-time program updates
■ Status LEDs for heartbeat, upstream and downstream communications
■ Two dedicated inputs for Cabinet Tamper and Power Failure status
■ On-board RS-485 termination jumpers
■ Easy to configure dip switches for address and communication speeds
■ On-board program configuration and clock battery backup
21
LNL-500W
OnGuard
Security
Server
Ports
2 3
Schlage Wireless
OnGuard Integration
for PIM-485-OTD
LNL-500W
LOCAL AREA NETWORK (TCP/IP)
Ports 2 - 5
Access Control
CORPORATE HEADQUARTERS
PIM-485-OTD
Note: Up to 16 MIRL, IRL, WRI or WPR per LNL-500W
WA 5296
Cylindrical
WRI-OTD
WA 5696 Mortise
Reader Options
LNL-500W
Lenel Wireless Reader Interface Gateway - 12 VDC or 12 VAC, (5 year lithium battery) 512KB standard memory, support for a
maximum of 16 Wireless readers per interface. Requires OnGuard software version 5.10.4xx or later
Power Supplies & Enclosures
LNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
Lenel UL Listed 4 A, 110 VAC Power Supply - 12 VDC or 24 VDC 4 A output (switch selectable), 120 VAC input, continuous supply
current with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable
(battery optional), UL-listed
Lenel UL Listed Power Supply - 12 VDC or 24 VDC 6 A output (switch selectable), 120 VAC (1.6 amps) input, continuous supply
current with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable
(battery optional), UL-listed
Battery Kit - 12 VDC, 12 AH battery (PS-12120)
Specifications
Primary Power (DC or AC)
DC input:
AC input:
Memory and Clock backup
Environmental
Temperature:
Humidity:
Mechanical
Dimensions:
Weight:
Approvals
Supported Readers
* The LNL-500W is designed for use in low voltage, power limited, class 2 circuits only.
12 VDC ± 15%. 250 mA
12 VAC ± 15%. 400 mA RMS
3 V lithium, type BR2325
Operating: 32° to 158° F (0° to +70° C)
Storage: -67° to 185° F (-55° to +85° C)
0 to 95% RHNC
6 x 5 x 1 in. (152 x 127 x 25 mm)
8 oz. (230 g) nominal
UL 294-listed, CE-marked, RoHS compliant
Schlage Wireless - WA 5296, WA 5696, WA 5694, WA 993, WRI, WPR
22
Star Multiplexer
LNL-8000
The Star Multiplexer from Lenel is designed to implement star topology on a downstream port of
any Lenel Intelligent System Controller or on any host communication port of any OnGuard server.
Up to eight RS-485 (2-wire) connections or four RS-485 (4-wire) connections can be made
downstream of the LNL-8000. The Lenel Star Multiplexer requires 12 VDC for power. It allows
communication protocol conversion, and provides connection with alternate communication
devices to extend effective distances.
Access Control
The master or host interface can use either RS-232 or RS-485 (2-wire) communication. The Lenel
Star Multiplexer interfaces upstream with the Lenel ISC, and downstream with one of many Lenel
RS-485 products (including the LNL-1100 Input Control Module, LNL-1200 Output Control Module,
LNL-1300 Single Reader Interface Module, LNL-1320 Dual Reader Interface Module and
LNL-500A, LNL-500B, or LNL-500W Gateway Interface Modules) on each downstream port (ports
2-9). A maximum of eight (8) devices are allowed per downstream port.
Features and Functionality
■ Host communications - 38.4 Kbps direct wire (RS-232/RS-485 multidropped)
■ 12 VDC input power
■ Status LEDs for heartbeat, upstream and downstream communication
■ Support for either 2-wire or 4-wire RS-485 topologies
■ RS-485 on-board termination is jumper selectable
■ Can be used for retrofit and new wiring configurations
23
LNL-8000
OnGuard
Security
Server
LNL-8000
Star Multiplexer
23456789
Intelligent
System
Controller
1234
1234
Up to 32 Downstream
RS-485 Devices
(up to 8 per port)
Intelligent
System
Controller
1234
LNL-8000
Star Multiplexer
(Up to 4 multiplexers)
23456789
LNL-1300
LNL-1320
Access Control
Intelligent
System
Controller
Mechanical and Architectural Characteristics and Wiring
Requirements
Communications
The acceptable power supply is 12 VDC. Locate the power source as close as possible to the LNL-8000.
Use a minimum of 18 AWG (one twisted pair) wiring for the power supply.
Communication with the Intelligent System Controller is via a 2-wire or 4-wire RS-485 interface. The interface allows multidrop
communication on a single ISC port, up to 4,000 feet (1219 m) away per port. It also can be used to convert a single RS-232
communication port to a multidrop RS-485 port. Use twisted pair(s) with a minimum of 24 AWG and a shield for communication.
The 2-wire or 4-wire communications with end-of-line termination are jumper-selectable.
Power Supplies & Enclosures
LNL-AL400ULX
LNL-AL600ULX-4CB6
ABT-12
Lenel UL-listed 4 A, 110 VAC power supply - 12 VDC or 24 VDC 4 A output (switch-selectable), 120 VAC input, continuous supply
current with enclosure (12 x 16 x 4.5 in. / 305 x 406 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable
(battery optional), UL-listed
Lenel UL-listed power supply - 12 VDC or 24 VDC 6 A output (switch-selectable), 120 VAC (1.6 amps) input, continuous supply
current with enclosure (18 x 24 x 4.5 in. / 457 x 610 x 114 mm), lock and open frame transformer, tamper switch, UPS-capable
(battery optional), UL-listed
Battery kit - 12 VDC, 12 AH battery (PS-12120)
Specifications
Primary Power (DC or AC)
DC input:
Environmental
Temperature:
Humidity:
Mechanical
Dimensions:
Weight:
Approvals
* This module is for use in low voltage, power limited, class 2 circuits only.
12 VDC ± 15%, 250 mA
Operating: 32° to 158° F (0° to +70° C)
Storage: -67° to 185° F (-55° to +85° C)
0 to 95% RHNC
6 x 5 x 1 in. (152 x 127 x 25 mm)
4 oz. (180 g) nominal
UL 294 and 1076-listed, CE-marked
24
Magnetic Card Access Reader
LNL-2005W
Lenel Systems International’s magnetic card access readers are durable, dependable, convenient,
and competitively-priced. The magnetic card access readers are available in both 12 VDC and
optional 5 VDC models. The readers have a fully-weatherized metal casing shell that provides
strength and durability. The readers are first treated with an anti-corrosion film, then coated with a
tough, abrasion-resistant, beige or black textured finish that complements any interior or exterior
decor. The readers accept low and high coercivity magnetic stripe cards. Track 2 magnetic
readers are standard, but Track 1 and Track 3 readers are available optionally.
The readers communicate to the Intelligent System Controller (ISC) through one of two reader
Access Control
interface modules. The single (LNL-1300) or dual (LNL-1320) reader interface module interprets
magnetic (Clock/Data) data from the reader, and sends the signal back to the ISC via RS-485
communication. The reader can be located up to 500 feet (152 m) away from the reader interface
module.
Features
■ 12 VDC power supply (optional 5 VDC available)
■ Bidirectional card swipe
■ One million card pass read head
■ Choice of three attractive weatherproof finishes: black, beige, antique brass
■ Single bicolored LED for reader status
■ Audible indicator beeper contacts
■ Strike controlled by reader interface
■ DIP switch-selectable data outputs
■ Maximum 500 feet (152 m) distance from reader interface module
■ RJ-45 jack for quick installation
■ Track 2 standard (Track 1 and 3 optional)
Specifications
Primary power (DC)
DC input:
* The reader is for use in low voltage, power-limited, class 2 circuits only.
12 V model: 12 VDC (10.2 to 13.8 VDC)
5 V model: 5.8 VDC (4.9 to 6.4 VDC)
Current:
50 mA maximum, 25 mA typical
Environmental
Temperature:
Operating: 32° to 158° F (0° to +70° C)
Storage: -67° to 185° F (-55° to +85° C)
Humidity:
0 to 95% RHNC
Mechanical
Dimension:
1.95 x 5.50 x 1.30 in. (50 x 140 x 33 mm)
Weight:
10 oz. (290 g) nominal
Approvals
25
UL 294 and 1076-listed, CE-marked
Magnetic Card Access Readers
LNL-2010/2020 series
Lenel Systems International’s Magnetic Card Access Readers are durable, dependable,
convenient and competitively priced. The Magnetic Card Access Readers are available in both 12
VDC and optional 5 VDC models. The LNL-2010W is a magnetic swipe only reader, and the
LNL-2020W includes a twelve-position keypad (available with an indestructible keypad). The
readers have a fully weatherized metal casing shell, which provides strength and durability. The
readers are first treated with an anti-corrosion film and then coated with a tough, abrasion
resistant, beige or black textured finish that complements any interior or exterior decor. The
standard, but optional Track 1 or Track 3 readers are available.
The readers communicate with the Intelligent System Controller (ISC) through one of two reader
interface modules. The single (LNL-1300) or dual (LNL-1320) reader interface module interprets
the Wiegand communication (Data 1/Data 0 or Clock and Data) from the reader and sends the
signal back to the ISC via RS-485 communication. The reader can be located up to 500 feet
Access Control
readers accept low and high coercivity magnetic stripe cards. Track 2 magnetic readers are
(152 m) away from the reader interface module.
Features
■ Host communications - 38.4 Kbps direct wire (RS-232/RS-485 multidropped), Ethernet TCP/IP,
or dial-up communication
■ 12 VDC power supply (optional 5 VDC available)
■ Bidirectional card swipe
■ One million card pass read head
■ Choice of three attractive weatherproof finishes: black and beige (antique brass optional)
■ Two single-color LEDs for reader status
■ Track 2 default (optional Track 1 and 3)
■ Audible indicator beeper contacts
■ Strike controlled by reader interface module
■ DIP switch selectable data outputs
■ Maximum 500 feet (152 m) distance from reader interface module
■ RJ-45 jack for quick installation
■ Optional tamper switch
■ 12-position keypad (LNL-2020W only)
■ (Optional) indestructible keypad, LNL-2020W-NDK
Specifications
Primary power (DC)
DC input:
* The ISC is for use in low voltage, power-limited, class 2 circuits only.
12 V Model: 12 VDC (10.2 to 13.8 VDC)
5 V Model: 5.8 VDC (4.9 to 6.4 VDC)
Current:
50 mA maximum, 25 mA typical
Environmental
Temperature:
Operating: 32° to 158° F (0° to +70° C)
Storage: -67° to 185° F (-55° to +85° C)
Humidity:
0 to 95% RHNC
Mechanical
Dimension:
1.9 x 5.5 x 1.3 in. (50 x 140 x 33 mm)
Weight:
10 oz. (290 g) nominal
Approvals
UL 294 and 1076-listed, CE-marked
26
Proximity Reader
LenelProx LPSR-2400
The LenelProx LPSR-2400 special range proximity reader is Lenel’s latest engineering
achievement. With a respectable read range of 4 to 5.5 in. (102 to 140 mm), the LPSR-2400
delivers exceptional read range without compromising quality, durability, or performance.
The LPSR-2400 is a full-featured, Wiegand-compatible reader with LED and annunciator. The
LPSR-2400 reader is metal-compensated, resulting in minimal loss of read range when mounted
on a metal mullion.
Access Control
The LPSR-2400’s electronics are potted in UL-approved potting compound to seal them against
adverse environmental conditions. The reader is manufactured in an ISO 9000-certified facility to
meet the highest quality standard. The attractive enclosure comes in a dark gray or beige color,
and may be mounted on mullions or single-gang electrical boxes, or directly to an interior or
exterior wall.
Features
■ Read range: 4 to 5.5 in. (102 to 140 mm)
■ Electronics potted with epoxy compound for protection in demanding environmental applications
■ LED for visual feedback, piezo for audio feedback
■ Compatible with all Wiegand access control systems
■ Industry standard Wiegand (26- to 56-bit) output
■ Attractive high-tech enclosure
Specifications
■ Transmitting frequency: 125 kHz
■ Voltage: 5 to 12 VDC
■ Current requirement: 40 to 70 mA
■ Output format: Wiegand
■ Operating temperature: -31° to 150° F (-35° to 65° C)
■ Operating humidity: 0 to 95% non-condensing
■ Weight: 4 oz. (113 g)
■ Dimensions: 4.5 x 1.8 x 0.7 in. (114 x 45 x 18 mm)
■ Color: Dark gray (standard) or beige
■ Cable: 10 conductor (#22 AWG) stranded with continuous shield for typical Wiegand installations
■ Certifications: Complies with FCC Part 15, UL 294-Listing and CE-Mark pending
27
Mullion Mount Proximity Reader
LenelProx LPMM-6800
Lenel’s standard mullion mount reader (LPMM-6800) offers the read range of a mid-range reader
at the cost of a “mini.” It is designed to be mounted directly on a metal door frame/mullion.
Because it is metal-compensated, there is minimal reduction in read range. The LPMM-6800 has a
read range of 6 to 8 in. (152 to 203 mm). It is designed for indoor and outdoor applications.
The LPMM-6800’s electronics are potted with a UL-approved compound that makes them
the highest quality standard. It is highly reliable, warranted for life, and available in either dark gray
(standard) or beige color.
The LPMM-6800 reader can easily be configured to meet the needs of virtually any access control
system. The reader outputs both Wiegand and RS-232 data, and features annunciator and LED
feedback.
Access Control
impervious to the elements. The reader is manufactured in an ISO 9000-certified facility to achieve
Features
■ Read range: 6 to 8 in. (152 to 203 mm)
■ Compact modular design for metal frame (mullion) mounting
■ Electronics potted with epoxy compound for protection in demanding environmental applications
■ LED for visual feedback, piezo for audio feedback
■ Industry-standard Wiegand and RS-232 output
■ Indoor and outdoor application
Specifications
■ Transmitting frequency: 125 kHz
■ Voltage: 5 to 12 VDC
■ Current requirement: 50 to 80 mA
■ Audio alarm: 4 kHz burst
■ Output formats: Wiegand & RS-232
■ Operating temperature: -31° to 150° F (-35° to 65° C)
■ Operating humidity: 0 to 95% non-condensing
■ Weight: 6 oz. (170 g)
■ Dimensions: 6.0 x 1.75 x 1.0 in. (152 x 44 x 254 mm)
■ Color: Dark gray (standard) or beige
■ Cable: 10 conductor (#22 AWG) stranded with continuous shield for typical Wiegand installations
■ Certifications: Complies with FCC Part 15, UL 294-Listing and CE-Mark pending
28
Proximity Reader
LenelProx LPSP-6820
The LenelProx LPSP-6820 proximity reader is ideally suited for applications where a tasteful
appearance makes a difference. It has an attractive package that looks good whether it is placed
outside the boardroom or at the front gate in the rain or snow.
The LPSP-6820 offers a stylish appearance and a superior read range of 6 to 8 in. (152 to 203
mm). It is designed to be mounted on a standard single-gang electric wall box, or on the surface of
an interior or exterior wall. The LPSP-6820 is available in dark gray or beige color, and is certain to
Access Control
blend in with the architectural design of any building. It is easily installed, and the two-piece
construction allows the covers to be switched to accommodate color changes.
The LPSP-6820 outputs Wiegand and RS-232 formats and is compatible with all access control
systems. The electronics are potted with UL-approved potting compound that protects the reader
from harsh environmental conditions. It is manufactured in an ISO 9000-certified facility to achieve
the highest quality standards. The LPSP-6820 is highly reliable, warranted for life and capable of
providing the best read range in its class.
Features
■ Read range: 6 to 8 in. (152 to 203 mm)
■ Electronics potted with epoxy compound for demanding environmental applications
■ LED for visual feedback, piezo for audio feedback
■ Industry-standard Wiegand and RS-232 output
■ Proximity technology – no contact required
■ Attractive, high-tech enclosure
■ Indoor and outdoor applications
Specifications
■ Transmitting frequency: 125 kHz
■ Voltage: 5 to 12 VDC
■ Current requirement: 50 to 80 mA
■ Audio alarm: 4 kHz burst
■ Output formats: Wiegand and RS-232
■ Operating temperatures: -31° to 150° F (-35° to 65° C)
■ Operating humidity: 0 to 95% non-condensing
■ Weight: 8 oz. (227 g)
■ Dimensions: 4.6 x 3.1 x 0.65 in. (117 x 79 x 17 mm)
■ Color: Dark gray (standard) or beige
■ Cable: 10 conductor (#22 AWG) stranded with continuous shield for typical Wiegand installations
■ Certifications: Complies with FCC Part 15, UL 294-Listing and CE-mark pending
29
Proximity Reader with Keypad
LenelProx LPKP-6840
The LenelProx LPKP-6840 reader is a combination keypad and switchplate proximity reader. It is
specifically designed for high-security applications that require dual verification.
The LPKP-6840 proximity reader offers dual functionality and a superior read range of 6 to 8 in.
(152 to 203 mm). It is designed to mount on a standard single-gang electric wall box, or on the
surface of an interior or exterior wall. The entire unit is UL 294-listed as an indoor/outdoor access
The LPKP-6840 keypad/proximity reader outputs industry-standard Wiegand (26 to 56 bit) format.
The keypad output is programmable to match the requirements of a majority of access control
systems. The proximity reader also simultaneously outputs an RS-232 signal, which duplicates the
Wiegand output from the proximity cards/tags for integration with time and attendance or debit
systems. It is manufactured in an ISO 9000-certified facility to achieve the highest quality
Access Control
control device.
standards. The LPKP-6840 is highly reliable, warranted for life, and capable of outputting Wiegand
data in multiple configurations.
Features
■ Read range: 6 to 8 in. (152 x 203 mm)
■ LED for visual feedback, piezo for audio feedback
■ Industry-standard Wiegand and simultaneous RS-232 output
■ Lifetime warranty
■ Available in a choice of keypad output configurations (default is 8 bit)
Specifications
■ Transmitting frequency: 125 kHz
■ Voltage: 5 to 12 VDC
■ Current requirement: 50 to 120 mA
■ Audio alarm: 4 kHz burst
■ Output formats:
• Wiegand and RS-232 for card/tag reader
• Wiegand only for keypad
■ Operating temperatures: -31° to 150° F (-35° to 65° C)
■ Operating humidity: 0 to 95% non-condensing
■ Weight: 8 oz. (227 g)
■ Dimensions: 4.6 x 3.1 x 0.875 in. (117 x 79 x 22 mm)
■ Color: Dark gray or beige
■ Cable: 10 conductor stranded with continuous shield for typical Wiegand installations
■ Certifications: Complies with FCC Part 15, UL 294-Listing and CE-Mark pending
30
Mid-Range Proximity Reader
LenelProx LPMR-1824
The LenelProx LPMR-1824 is a standout among mid-range proximity readers. It boasts an
industry-best 18 to 24 in. (457 to 610 mm) read range, and a compact enclosure. No more
misreads or fumbling to get the card close enough to the reader. The LPMR-1824 reads at
maximum range every time. And it does so at an unprecedented 600 mA at 12 VDC.
The LPMR-1824 is designed for indoor or outdoor applications. Its electronics are potted with a
UL-approved epoxy to seal them against adverse environmental conditions. The LPMR-1824 is
Access Control
manufactured in an ISO 9000-certified facility to achieve the highest quality standard. It is highly
reliable and has a lifetime warranty. It has both Wiegand and RS-232 protocol interfaces, and is
compatible with all standard access control systems.
The two-piece construction of the LPMR-1824 makes for fast and easy installation.
Features
■ Read range: 18 to 24 in. (457 to 610 mm)
■ Electronics potted with epoxy compound for weather resistance
■ LED for visual feedback, piezo for audio feedback
■ Compatible with all Wiegand access control systems
■ Channeled housing allows for rear or side mounting
■ Proximity technology - no contact required
■ Metal-compensated version available for mounting on metal surface
■ Industry standard Wiegand and RS-232 data output
Specifications
■ Transmitting frequency: 125 kHz
■ Voltage: 5 to 12 VDC
■ Current requirement: 250 to 600 mA
■ Audio alarm: 4 kHz burst
■ Operating temperature: -31° to 150° F (-35° to 65° C)
■ Operating humidity: 0 to 95% non-condensing
■ Weight: 25 oz. (709 g)
■ Dimensions: 8.0 x 8.0 x 1.0 in. (203 x 203 x 254 mm)
■ Color: Dark gray
■ Cable: 10 conductor (#22 AWG) stranded with continuous shield for typical Wiegand installations
■ Certifications: Complies with FCC Part 15, UL 294, 1076-Listing and CE-Mark pending
31
Long Range Proximity Reader
LenelProx LPLR-911
The LenelProx LPLR-911 long range reader is in a class by itself, with an industry-best, 9 to 11 ft.
(2.75 x 3.35 m) read range within and a compact package. The LPLR-911 is ideal for outdoor
applications such as AVI (automatic vehicle identification), parking entry, and gate controls. The
LPLR-911 is also perfect for indoor applications such as asset monitoring and tracking.
Operating in the license-free 900 MHz band, the LPLR-911 is the first access control reader to
output. The multi-tag capability makes it easy to set up portal or hallway asset monitoring stations
to determine the flow of assets.
The innovative construction of the LPLR-911 reader seals it against adverse environmental
conditions. It is manufactured in an ISO 9000-certified facility to achieve the highest quality
standard. The reader delivers an impressive combination of high styling and superior range. It
Access Control
combine the convenience of 900 MHz technology with a fast multi-tag feature and Wiegand format
offers Wiegand and RS-232 protocol interfaces and compatibility with all standard access control
systems.
Features
■ Read range: 9 to 11 ft. (2.75 to 3.35 m) with 1.0 A at 6.5 VDC, to 0.4 A at 15 VDC
■ Housing sealed for weather resistance
■ Anti-collision technology and multiple tag reading capability
■ Compatible with existing access control system and asset tracking systems
■ Utilizes passive tag technology (no battery)
Specifications
■ Industry standard Wiegand and RS-232 data output
■ Transmitting frequency: 902 to 928 MHz
■ Voltage: 6.5 to 15 VDC
■ Current requirement: 1.0 to 0.4 A
■ Output formats: Wiegand and RS-232
■ Operating temperature: -31° to 150° F (-35° to 65° C)
■ Operating humidity: 0 to 95% non-condensing
■ Weight: 37.5 oz. (1.06 kg)
■ Dimensions: 8 x 9.5 x 1.125 in. (203 x 241 x 286 mm)
■ Color: Beige
■ Cable: 9 conductor stranded (#22 AWG) with continuous shield for typical installations
■ Certifications: Complies with FCC Part 15, UL 294-Listing and CE-Mark pending
32
Lenel OpenCard™ Readers
LNL-XF
The Lenel OpenCard Reader series includes the most flexible readers in the industry. A single
reader supports all applicable ISO standards (14443 and 15693), including the new U.S.
Government PIV standard. All Lenel OpenCard Readers contain both 125 kHz proximity and
13.56 MHz contactless smart card support in one unit. Lenel OpenCard Readers provide
compatibility with Lenel prox, HID® proximity, GE/CASI ProxLite®, XceedID proximity, AWID
proximity and most 13.56 MHz technologies (see chart on back). By offering 125 kHz and 13.56
MHz technology in one reader, Lenel protects customers from obsolescence in the transition from
Access Control
proximity technology to contactless smart card technology. Even if customers want to continue
using proximity technology today, the new Lenel OpenCard Readers offer economical migration to
the latest in smart card technology while accommodating their budget or timeline.
Product Applications
The mullion reader is perfect for narrow-rail mullion installations. It can be used as a sleek and
unobtrusive unit, as well as for standard wall-mounted reader applications.
The mid-range reader is ideal for mounting on single gang US electrical boxes. The read range
provided by this attractive package makes it the standard of choice for most wall-mounted
installations.
The mid-range keypad reader is ideal for higher security applications where two-factor (card
and/or PIN) authentication is desired. This reader may be mounted on a standard U.S. single gang
electrical box, or used in any typical wall-mounted application.
Features and Functionality
■ Compatibility: compatible with industry standard 125 kHz proximity and 13.56 MHz contactless
technologies
■ Easy migration
■ Optional GSA approved PIV support
■ Modular design: allows easy removal or addition of keypad in the field
■ Read range: up to 8 in. (203 mm), depending on card technology
■ Integrated tamper detection
■ Tri-state LED (red, green, amber): Visual indicator and audio feedback representing status and
activity information
■ Accommodates interior, exterior, metal and non-metal installation environments
■ Lifetime warranty against defective workmanship and materials
33
LNL-XF
Supported Standards and Technologies
LenelProx
GE CASI ProxLite®
HID® Proximity
XceedID™
AWID® Proximity
ISO 15693
13.56 MHz Vicinity
XceedID ISO-X™ Secure Sector
Infineon my-d® Secure Sector
HID iCLASS® Serial Number
Infineon my-d® Serial Number
Inside Contactless PicoTag® Serial No.
ST Microelectronics® Serial Number
Texas Instruments Tag-It® Serial No.
ISO 14443
13.56 MHz Proximity
Lenel OpenCard Format Sector
XceedID Secure MIFARE
DESFire® Serial Number
MIFARE® Serial Number
U.S. Government PIV Data Model
Access Control
125 kHz Proximity
Reader Options
Standard Readers
LNL-XF1100D
LNL-XF2100D
LNL-XF2110D
PIV Readers
LNL-XF1100D-PIV
LNL-XF2100D-PIV
LNL-XF2110D-PIV
Description
(Standard Black) Mullion mount; Wiegand output
(Standard Black) 1-Gang US mount; Wiegand output
(Standard Black) 1-Gang US mount; Keypad; Wiegand output
125 kHz and 13.56 MHz
ISO 15693 and ISO 14443
-31° to 151°F (-35° to 67°C)
Max. Read Range
125 kHz:
LNL-XF1100D, up to 5” (127 mm)
LNL-XF21XXD, up to 8” (203 mm)
13.56 MHz:
ISO 15693
• LNL-XF1100D, up to 4.5” (114 mm)
• LNL-XF21XXD, up to 6” (152 mm)
ISO 14443 MIFARE Standard
• LNL-XF1100D, up to 2” (51 mm)
• LNL-XF21XXD, up to 3” (76 mm)
ISO 14443 MIFARE DESFire
• LNL-XF1100D, up to 1.5” (38 mm)
• LNL-XF21XXD, up to 2.5” 64 mm)
ISO 14443 PIV
• LNL-XF1100D, up to 1” (25 mm)
• LNL-XF21XXD, up to 2” (51 mm)
*Maximum read range depends on credential type/form factor and
installation conditions
Specifications
Frequency
Standards
Operating Temperature
Physical Dimensions (HWD)
LNL-XF1100D:
LNL-XF21XXD:
Weight
LNL-XF1100D:
LNL-XF21XXD:
Voltage Range
Max. Current Requirement
LNL-XF1100D:
LNL-XF2100D:
LNL-XF2110D:
Material
System Interface
Cable Specification
Cabling Distance
Certifications
5.85” x 1.72” x 1.14”
(149 cm x 43 cm x 29 mm)
5.85” x 4.5” x 1.45”
(149 cm x 114 cm x 37 mm)
0.6 lbs. (.27 kg)
1.05 lbs. (.48 kg)
8 to 16 VDC
Avg. 95 mA DC, Peak 254 mA DC
Avg. 95 mA DC, Peak 218 mA DC
Avg. 120 mA DC, Peak 215 mA DC
PBT Polymer
Wiegand (Standard)
22AWG 12 Conductor Shielded
Wiegand Output: 500 ft. (152m)
FCC Certification
Canadian FCC Certification
UL 294-Listed, CE-Marked
R&TTE Directive (15 EU Countries)
GSA Approved for FIPS-201
(PIV models only)
34
Lenel OpenProx™ Reader
LNL-XF1050
The Lenel OpenProx Reader is the most flexible 125 kHz proximity card reader in the industry. It
supports all major 125 kHz card standards. The Lenel OpenProx Reader provides compatibility
with HID® proximity, GE/CASI ProxLite®, XceedID® proximity, AWID®, and LenelProx card formats.
Lenel provides a single compact reader that can integrate diverse proximity card populations, or
allow seamless transition from one 125 kHz technology to another.
Product Applications
Access Control
The mullion reader is perfect for narrow-rail mullion installations. It can be used as a sleek and
unobtrusive unit, as well as in standard wall-mounted reader applications.
Features and Functionality
■ Compatible with industry standard 125 kHz proximity technology
■ Easy Migration
■ Tri-state LED (red, green, amber): Visual indicator and audio feedback representing status and
activity information
■ Accommodates interior, exterior, metal and non-metal installation environments
■ Lifetime warranty against defective workmanship and materials
Specifications
Frequency:
125 kHz
Operating temperature:
-31° to 151°F (-35° to 67°C)
Physical dimension (HWD):
4.1” x 1.72” x 1.0”
(104 cm x 44 cm x 25 mm)
Weight:
0.45 lbs. (.20 kg)
Voltage range:
5 to 16 VDC
Power supply:
Linear DC
Max. current requirement:
Avg. 55 mA DC
Peak 167 mA DC
Material:
PBT Polymer
Max. read range:
Up to 3” (76 mm)*
* Maximum read range depends on credential type/form
factor and installation conditions
System interface:
Wiegand
Cable specification:
Recommended cable is 22AWG (18AWG preferred),
minimum 5 conductor shielded (4 plus shield)
in retrofit installs.
Cabling distance:
Wiegand Output 18 AWG: 500 ft. (152 m)
Wiegand Output 22 AWG: 200 ft. (60 m)
Certifications:
FCC Certification
Canadian FCC Certification
UL 294 and 1076-listed
R&TTE Directive (15 EU Countries)
CE-marked
35
Three-Factor Biometric Reader Recessed Enclosure
LNL-BIO-007-ENC
The LNL-BIO-007 Reader Recessed Enclosure is designed to mount any model of the BIO-007
series of readers. The enclosure comes standard with a brushed aluminum finish plate.
Alternatively, it can be ordered with black or gold finish plates to match BIO-007 reader color
options. The enclosure comes standard with six ¾” to 1” (19 to 25 mm) conduit knock outs,
security screws and a security tool. The recessed enclosure contains a built-in 24VAC input to
12VDC output power for a single BIO-007 reader. The enclosure can be used for new or existing
Specifications
Enclosure
■ Dimensions (approximate): 11.25 x 5.25 x 3.25 in. (286 x 133 x 83 mm)
Access Control
installations.
■ Color: Gray
■ Finish plate: brushed aluminum is standard; black or gold optional
■ Includes reader mounting screws and hardware
■ Suggested mounting height - approximately 54” (1371.6 mm) from floor to top of unit
Linear Power Supply/Charger
■ 12VDC output
■ 2 Amps of continuous supply current @ 12VDC
■ 24 VAC transformer requirements per unit
■ 24 VAC/40VA for 12VDC output (not included)
■ Filtered and electronically regulated outputs
■ Short circuit and thermal overload protection
■ Built-in charger for sealed lead acid or gel type battery backup
■ Maximum charge current: 0.3 Amp
■ Zero voltage drop upon transfer to battery backup
■ AC input and DC output LED indicators
■ Lifetime warranty
Board
■ Dimensions (approximate): 3.0 x 2.5 x 1.5 in. (76 x 64 x 38 mm)
36
Three Factor Biometric Reader
LNL-BIO-007
The LNL-BIO-007 access reader is durable, dependable, and competitively priced. Designed for
indoor or outdoor use, the reader combines three forms of authentication: proximity reader, PIN
pad, and fingerprint sensor. The PIN and fingerprint authentication are standard; the proximity
reader is optional. All three reader modes can be configured to support timezone control.
The BIO-007 transmits a credential number to the Intelligent System Controller through a Wiegand
interface. The ISC then delivers fingerprint template(s) to the BIO-007 though the LNL-500B
Biometric Gateway and matching is performed within the BIO-007. The results of the match are
Access Control
then returned to the Gateway for appropriate action and reporting to OnGuard.
The indestructible keypad is based on BaranTec’s patented Piezo Switch technology. The
power-driven Bioscrypt fingerprint sensor utilizes a powerful DSP processor. Unlike other biometric
products, this sensor is hidden until a valid credential and/or PIN is presented. Then the fingerprint
sensor door opens. After verification occurs, the fingerprint sensor door closes into a secure
vandal-resistant position.
Features and Functionality
■ 12 VDC power supply @ 1.8 amps
■ Three factors of authentication: card, PIN, fingerprint
■ Data output: Wiegand Data1/Data0
■ Biometric output: RS-485
■ Keypad interface: 8-bit burst
■ Keypad layout: 4 across & 3 down
■ Brushed aluminum finish, also available in black finish
■ Vandal-resistant design
■ Weather-resistant housing
■ Three LEDs for reader status
■ Audible indicator buzzer
■ 24-month warranty
37
LNL-BIO-007
LNL-2000 Intelligent
System Controller
LNL-1300/1320
LNL-500B
RS - 485 multidrop
RS-485 to fingerprint
sensor (3 wires)
Proximity and keypad
Wiegand output to reader
interface module (6 wires)
Access Control
BIO-007
Reader Options
LNL-BIO007
LNL-BIO007-HID
LNL-BIO007-HIDW
Reader unit with PIN pad and fingerprint sensor.
Reader unit with built-in HID technology (HID 125 KHz proximity sensor).
Outdoor reader with thermal heat kit. Recommended for readers installed outdoors, where temperature is below -4° F. (-20° C)
Reader Finishes
Standard
Alternate
Silver finish
Black finish (To specify the alternate finish, add the following suffix to the part number: -B)
Specifications
Primary Power (DC)
DC input:
Environmental
Temperature:
Humidity:
Mechanical
Case:
Dimensions:
Weight:
Read range:
Mounting height:
Technology
Supported:
Sensor:
FAR:
FRR:
Approvals
* The BIO-007 reader is for use in low voltage, power-limited, class 2 circuits only.
12 VDC @ 1.6 amps (12 VDC @ 1.8 amps with use of thermal heat kit)
32° to 122° F (0° to 50°C), operating. (-4° to 158° F / -20° to +70°C with use of thermal heat kit)
0 to 95% RHNC
Brushed aluminum construction, anodized
3.94 x 8.92 x 2.6 in. (100 x 227 x 66 mm)
4.71 lbs. (2.1365 kg) nominal
1 to 2 in. ( 25 to 51 mm)
Between 48 and 54 in. (1219 and 1372 mm) recommended
Encoding: 125 KHz HID proximity cards
Bioscrypt
(False Acceptance Rate) 0.2%
(False Rejection Rate) 1.0%
CE-Marked
38
Indestructible Keypad
LNL-826S121NN
Lenel Systems International’s indestructible keypads offer the ultimate in strength and durability
where PIN entry and maximum security are required. With a tamperproof keypad and a
weatherproof, solid brushed aluminum casing, Lenel indestructible keypads are designed to
function dependably even in harsh climates or high-risk environments. The keypads are compliant
with the Americans with Disabilities Act (ADA) guidelines.
The LNL-826S121NN 12-position keypad is configured to have two keys across by six keys down,
Access Control
and is intended for use in mullion mounting applications. It features an eight-bit word data output
format, 12 to 28 volts DC power, 30 mA current draw, and red and green status LEDs. The keypad
uses solid state piezo sounder technology to provide audible feedback. A natural aluminum color
is standard, but other colors are also available upon request.
Features
■ Anodized graphics
■ Waterproof and dustproof IP68
■ 2 x 6 in. (51 x 152 mm) configuration keypad type
■ Click and lock mounting screws
Specifications
■ Protocol: 8 bit word output
■ Dimensions: 7.1 x 1.8 x 0.8 in. (44 x 181 x 19 mm)
■ Power: 12 to 28 VDC
■ Current: 30 mA
■ Environment: IP68; 100% RH
■ Temperature: -40° to 158 F° (-40° to +70° C)
■ FCC-certified, CE-marked
■ Brushed aluminum construction; other colors available optionally
Application Note
Lenel keypad readers can be used either by themselves or in conjunction with almost any other
reader technology. The eight-bit burst output format enables these keypads to be wired in parallel
with any other reader technology, including proximity, magnetic stripe, MIFARE, Vicinity, etc.
Detailed wiring information is provided in the Lenel hardware installation manuals.
39
Indestructible Keypad
LNL-834S121NN
Lenel Systems International’s indestructible keypads offer the ultimate in strength and durability
where PIN entry and maximum security are required. With a tamperproof keypad and a
weatherproof, solid brushed aluminum casing, Lenel indestructible keypads are designed to
function dependably even in harsh climates or high-risk environments. The keypads are compliant
with the Americans with Disabilities Act (ADA) guidelines.
down, and is intended for single gang electrical box installation. It features an eight-bit word data
output format, 12 to 28 volts DC power, 30 mA current draw, and red and green status LEDs. The
keypad uses solid state piezo sounder technology to provide audible feedback. A natural aluminum
color is standard, but other colors are also available upon request.
Access Control
The LNL-834S121NN 12-position keypad is configured to have three keys across by four keys
Features
■ Anodized graphics
■ Waterproof and dustproof IP68
■ 3 x 4 in. (76 to 102 mm) configuration keypad type
■ Click and lock mounting screws
Specifications
■ Protocol: 8 bit word output
■ Dimensions: 3.2 x 5.1 x 0.8 in. (81 x 130 x 19 mm)
■ Power: 12 to 28 VDC
■ Current: 30 mA
■ Environment: IP68; 100% RH
■ Temperature: -40° to 158° F (-40° to +70° C)
■ FCC-certified, CE-marked
■ Brushed aluminum construction; other colors available optionally
Application Note
Lenel keypad readers can be used either by themselves or in conjunction with almost any other
reader technology. The eight-bit burst output format enables these keypads to be wired in parallel
with any other reader technology, including proximity, magnetic stripe, MIFARE, Vicinity, etc.
Detailed wiring information is provided in the Lenel hardware installation manuals.
40
Indestructible Keypad with Lenel Proximity
BT-LPKP-NDK
The Lenel BT-LPKP-NDK indestructible keypad reader offers the ultimate in strength and durability
where proximity and PIN entry are required. With a tamperproof keypad and a weatherproof, solid
brushed aluminum casing, Lenel indestructible keypads are designed to function dependably even
in harsh climates or high-risk environments. The keypads are compliant with the Americans with
Disabilities Act (ADA) guidelines.
The model BT-LPKP-NDK reader is equipped with two electronically interlocked devices – a Lenel
Access Control
format proximity reader and a piezoelectric keypad – contained within a single, nearly
indestructible, metal housing. The 12-position keypad is configured to have three keys across by
four keys down, and is designed for both international and U.S. single gang electrical box
mounting applications. It features an eight-bit word data output format, 5 to 12 volts DC power, 120
mA current draw, and red and green status LEDs. The keypad uses solid state piezo sounder
technology to provide audible feedback. A natural aluminum color is standard, but other colors are
also available upon request.
Features
■ Anodized graphics
■ Waterproof and dustproof IP68
■ 3 x 4 in. (76 x 102 mm) configuration keypad type
■ Click and lock mounting screws
Specifications
■ Protocol: Wiegand + 8 bit word output
■ Dimensions: 5.4 x 3.3 x 1.2 in. (137 x 83 x 30 mm)
■ Power: 5 to 12 VDC
■ Current: 120 mA
■ Environment: IP68; 100% RH
■ Temperature: -4° to 158 F° (-20° to +70° C)
■ Read Range: 2 to 3 in. (51 to 76 mm)
■ FCC-Certified/UL, ULC- and CE-mark pending
■ Brushed aluminum construction; other colors available optionally
41
Indestructible Keypad with HID® Proximity or iCLASS™ 13.56
BT-ASPKP-HID/iCLASS
The Lenel BT-ASPKP-HID/BT-ASPKP-iCLASS indestructible keypad reader offers the ultimate in
strength and durability where proximity and PIN entry are required. With a tamperproof keypad
and a weatherproof, solid brushed aluminum casing, Lenel indestructible keypads are designed to
function dependably even in harsh climates or high-risk environments. The keypads are compliant
with the Americans with Disabilities Act (ADA) guidelines.
interlocked devices – an HID format proximity or iCLASS reader, and a piezoelectric keypad –
contained within a single, indestructible, metal housing. The 12-position keypad is configured to
have two keys across by five keys down, and is designed for both international and U.S. single
gang electrical box mounting applications. It features an eight-bit word data output format, 5 to 12
volts DC power, 150 mA current draw, and red and green status LEDs. The keypad uses solid
Access Control
The model BT-ASPKP-HID/BT-ASPKP-iCLASS reader is equipped with two electronically
state piezo sounder technology to provide audible feedback. A natural aluminum color is standard,
but other colors are also available upon request.
Features
■ Anodized graphics
■ Waterproof and dustproof IP68
■ 2 x 5 in. (51 x 127 mm) configuration keypad type
■ Click and lock mounting screws
Specifications
■ Protocol: Wiegand + 8 bit word output
■ Dimensions: 4.7 x 3.5 x 0.8 in. (120 x 90 x 20 mm)
■ Power: 5 to 12 VDC
■ Current: 150 mA
■ Environment: IP68; 100% RH
■ Temperature: -4° to 158 F° (-20° to +70° C)
■ Read Range: 1 to 2 in. (25 to 51 mm)
■ FCC-Certified Part 15, CE-marked
■ Brushed aluminum construction; other colors available optionally
■ Available in either 125 MHz proximity or 13.56 iCLASS
42
Lenel Command Keypad
LNL-CK
The LNL-CK Lenel Command Keypad integrates a 32-character backlit LCD display with a
16-position keypad and a reader port. The command keypad serves as a command reader,
a reader from which user commands can be issued to execute local I/O functions. Reader
command programming is accomplished using the OnGuard System Administration application.
The LNL-CK display indicates time in either 12 or 24-hour clock format. The format is automatically
chosen based on the regional settings of the computer on which the Communication Server is
Access Control
running. The LNL-CK display also provides command status and other text feedback during reader
operations. For example, when performing the Extended Held Open command, the LNL-CK
displays the countdown time before the Held Open time is reached, as well as basic intrusion
arm/disarm functions.
The LNL-CK communicates with the Lenel Intelligent System Controller (ISC) either through direct,
multidrop, 2-wire RS-485 communication to the ISC, or through a reader port of a Lenel Dual
Reader Interface Module (LNL-1320).
The LNL-CK may be configured in one of three ways: as a stand-alone RS-485 device, as an
alternate reader to a primary reader, or as a reader device connected to the Wiegand input of a
LNL-1320. In any of these modes, an optional reader with a Data1/Data0 or clock/data output may
be connected to the LNL-CK to provide Card Only, Card or PIN, or Card and PIN capability.
Features and Functionality
■ 32-character backlit LCD display
■ 16-position keypad with 4 function keys
■ Supports all “approved for use” reader technologies from Lenel that communicate using
Data1/Data0 or clock/data communication
■ Arm, Disarm, Bypass and Force Arm alarm mask groups
■ Extended Held Open Time via Command Keypad with feedback
■ Reader command support
■ Works with all Lenel Intelligent System Controllers (LNL-500, LNL-1000, LNL-2000)
■ Supports reader mode changes by Timezone control
■ Supports PIN mode on LNL-CK keypad. With optional reader, all other modes are also
supported
■ Ability to adjust backlight on/off times
■ Flash upgradable firmware
■ Built-in DIP switch selectable RS-485 termination
43
LNL-CK
Intelligent
System
Controller
2-WIRE RS-485 SERIAL BUS
RS-485
LNL-1320
LNL-CK
Alternate
Reader
Access Control
LNL-CK
Alternate
Reader
Specifications
Primary Power
Voltage:
Current:
12 VDC +/- 15%
175 mA terminal only
Reader
Power:
LED Control:
Buzzer Control:
Interface:
Pass-through (non-regulated)
2-wire or 1-wire bicolor LED
Available with 1-wire LED control
2-wire RS-485, or Wiegand
Technology
Communication:
Operating: 32° to 122° F (0° to 50° C)
Storage: -4° to 158° F (-20° to 70° C)
0% to 95% RHNC
Approvals
Environmental
Temperature:
Humidity:
Physical
Color:
Dimensions:
Weight:
Mounting:
White
6.75 x 5.00 x 1.0 in. (172 x 127 x 25 mm)
14 oz. (400 g) nominal
Surface-mount or 3-gang box
RS-485: up to 4000 ft. (1219 m) max,
24 AWG, 100 ohm impedance
Wiegand: up to 500 ft. (152 m) max,
18 AWG stranded wire
FCC approved, UL-listed, CE-marked
44
UL-Listed, Multi-Agency Power Supply/Charger
LNL-AL400ULX
The LNL-AL400ULX is a power-limited supply/charger that will convert a 115 VAC 50/60 Hz input,
into a power-limited 12 VDC or 24 VDC output (see specifications).
Features
■ LNL-CTX enclosure (gray with Lenel logo)
■ Offline power supply (AL400ULXL) mounted on custom Lenel bracket
Access Control
■ Tamper switch
■ Lenel lock with two keys
■ 16 stand-offs and 16 screws
■ Battery leads
■ Installation instructions
■ Can accommodate up to 2 Lenel Access Control modules
Specifications
■ UL 294 and 1076-listed
■ Switch selectable 12 VDC or 24 VDC power limited output
■ Class 2 rated
■ Input 115 VAC 50/60 Hz, 1.45 amp
■ Maximum charge current 0.7 amp
■ 4 amps continuous supply current at 12 VDC
■ 3 amps continuous supply current at 24 VDC
■ Filtered and electronically regulated outputs
■ Built-in charger for sealed lead acid or gel type batteries (Optional ABT-12)
■ Automatic switchover to standby battery when AC fails
■ AC input and DC output LED indicators
■ AC fail supervision (form C contacts)
■ Low battery supervision (form C contact)
■ Low battery disconnect prevents batteries from deep discharge
■ Thermal overload protection
■ Short circuit protection
■ Primary circuit switch for incoming 115 VAC
■ Power supply board dimensions: 4.3 x 7 x 1.8 in. (108 x 178 x 44 mm)
■ Enclosure dimensions: 12 x 16 x 4.5 in. (304 x 406 x 114 mm)
Ordering Information
45
Part Number:
Description:
LNL-AL400ULX
115 VAC configuration
ABT-12
Battery backup option
LNL-CTX
Cabinet only, with lock 12 x 16 x 4.5 in. (304 x 406 x 114 mm)
UL-Listed, Multi-Agency Power Supply/Charger
LNL-AL600ULX-4CB6
The LNL-AL600ULX-4CB6 is a power-limited supply/charger that will convert a 115 VAC 60 Hz
input, into a non-power-limited 12 VDC or 24 VDC output (see specifications)
Features
■ LNL-CTX-6 enclosure (gray with Lenel logo)
■ Power limited distribution module (PD4-CB)
■ Tamper switch
■ Lenel lock with two keys
■ 48 stand-offs and 48 screws
■ Battery leads
Access Control
■ Offline power supply (AL600ULXL) mounted on custom Lenel bracket
■ Installation instructions
■ Can accommodate up to 6 Lenel Access Control modules
Specifications
■ UL 294 and 1076-listed
■ Switch selectable 12 VDC or 24 VDC non-power limited output
■ Input 115 VAC 60 Hz, 1.9 amp
■ Maximum charge current 0.7 amp
■ 6 amps continuous supply current at 12 VDC or 24 VDC
■ Filtered and electronically regulated outputs
■ 100 mV peak output voltage ripple
■ 4 individual circuit breaker outputs
■ Surge protected outputs
■ Built-in charger for sealed lead acid or gel type batteries (Optional ABT-12)
■ Automatic switchover to standby battery when AC fails
■ Zero voltage drop when switched over to battery backup
■ AC input and DC output LED indicators
■ AC fail supervision (form C contacts)
■ Low battery and battery presence supervision (form C contact)
■ Thermal overload protection
■ Short circuit protection
■ Primary circuit switch for incoming 115 VAC
■ Power supply board dimensions: 4.3 x 7 x 1.8 in. (108 x 178 x 44 mm)
■ Enclosure dimensions: 24 x 18 x 4.5 in. (610 x 457 x 114 mm)
Ordering Information
Part Number:
Description:
LNL-AL600ULX-4CB6
115 VAC configuration
ABT-12
Battery backup option
LNL-CTX-6
Cabinet only, with lock 24 x 18 x 4.5 in. (610 x 457 x 114 mm)
46
CE-Marked Power Supply/Charger
LNL-400X-CE220
The LNL-400X-CE220 is a power-limited supply/charger that will convert a 230 VAC, 60 Hz input
into a power-limited, 12 VDC or 24 VDC output (see specifications).
Features
■ LNL-CTX enclosure (gray with Lenel logo)
■ AL400ULB power supply
Access Control
■ Tamper switch
■ Lenel lock with two keys
■ 16 standoffs and 16 screws
■ Battery leads
■ Installation instructions
■ Can accommodate up to 2 Lenel Access Control modules
Specifications
■ CE-marked
■ Switch-selectable, 12 VDC or 24 VDC, power-limited output
■ Class 2 rated
■ Input 230 VAC, 60 Hz, 1.45 amp
■ Maximum charge current 0.7 amp
■ 4 amps continuous supply current at 12 VDC
■ 3 amps continuous supply current at 24 VDC
■ Filtered and electronically regulated outputs
■ Built-in charger for sealed lead acid or gel type batteries (Optional ABT-12)
■ Automatic switchover to standby battery when AC fails
■ AC input and DC output LED indicators
■ AC fail supervision (form C contacts)
■ Low battery supervision (form C contact)
■ Low battery disconnect prevents batteries from deep discharge
■ Thermal overload protection
■ Short circuit protection
■ Primary circuit switch for incoming 230 VAC
■ Power supply board dimensions: 4.3 x 7 x 1.8 in. (108 x 178 x 44 mm)
■ Enclosure dimensions: 12 x 16 x 4.5 in. (304 x 406 x 114 mm)
Ordering Information
47
Part Number:
Description:
LNL-400X-CE220
230 VAC configuration
ABT-12
Battery backup option
LNL-CTX
Cabinet only, with lock 12 x 16 x 4.5 in. (304 x 406 x 114 mm)
CE-Marked Power Supply/Charger
LNL-600X6-CE220
The LNL-600X6-CE220 is a power-limited supply/charger that will convert a 230 VAC, 60 Hz input
into a non-power-limited, 12 VDC or 24 VDC output (see specifications)
Features
■ LNL-CTX-6 enclosure (gray with Lenel logo)
■ Power-limited distribution module (PD4-CB)
■ Tamper switch
■ Lenel lock with two keys
■ 48 standoffs and 48 screws
■ Battery leads
Access Control
■ AL600ULB power supply
■ Installation instructions
■ Can accommodate up to 6 Lenel Access Control Modules
Specifications
■ CE-marked
■ Switch-selectable, 12 VDC or 24 VDC, non-power-limited output
■ Input 230 VAC, 60Hz, 1.9 amp
■ Maximum charge current 0.7 amp
■ 6 amps continuous supply current at 12 VDC or 24 VDC
■ Filtered and electronically regulated outputs
■ 100 mV peak output voltage ripple
■ 4 individual circuit breaker outputs
■ Surge protected outputs
■ Built-in charger for sealed lead acid or gel type batteries (Optional ABT-12)
■ Automatic switchover to standby battery when AC fails
■ Zero voltage drop when switched over to battery backup
■ AC input and DC output LED indicators
■ AC fail supervision (form C contacts)
■ Low battery and battery presence supervision (form C contact)
■ Thermal overload protection
■ Short circuit protection
■ Primary circuit switch for incoming 230 VAC
■ Power supply board dimensions: 4.3 x 7 x 1.8 in. (108 x 178 x 44 mm)
■ Enclosure dimensions: 24 x 18 x 4.5 in. (610 x 457 x 114 mm)
Ordering Information
Part Number:
Description:
LNL-600X6-CE220
230 VAC configuration
ABT-12
Battery backup option
LNL-CTX-6
Cabinet only, with lock 24 x 18 x 4.5 in. (610 x 457 x 114 mm)
48
USB Capture Kit
CAM-20Z704-USB / CAM-21Z704-USBP
The Lenel USB Image CaptureKit offers many important features for capturing badgeholder
images. The capture kit includes a high resolution CCD (NTSC or PAL) camera with software
zoom capabilities, a fully-synchronized cool white built-in flash, a tripod system with a powered
base, TWAIN-compliant software, a USB communication cable and a universal power cable. The
camera is USB 2.0-compliant, producing high resolution live video for image capture using the
OnGuard ID CredentialCenter™ application by Lenel. The latest version of the TWAIN device
driver enables the user to control the camera’s zoom capabilities from within OnGuard. The built-in
flash illuminates both video fields evenly to minimize the effect of poor lighting environments.
Features and Functionality
■ USB 1.1 (USB 2.0 compliant)
■ Cool white LEDs replace hot incandescent lights & last up to 100 times longer
■ Single control button for camera & LED, transparent & seamless via USB
Credential
■ TWAIN-compliant software interacts with OnGuard and other imaging software
■ Rapid image download compared to still image cameras
■ Real-time subject setup and scene adjustment
■ Freeze frame perfection
USB Out
S-Video Out
Video Out
Power • LED
• Camera/Remote
49
CAM-20Z704-USB / CAM-21Z704-USBP
Camera Options
CAM-20Z704-USB
CAM-21Z704-USBP
USB NTSC CCD Image Capture Kit - includes CCD NTSC camera, synchronized cool white lights, telescoping stand, USB cable,
universal 110/220 VAC power supply and device drivers.
USB PAL CCD Image Capture Kit - includes CCD PAL camera, synchronized cool white lights, telescoping stand, USB cable,
universal 110/220 VAC power supply and device drivers.
Electrical
CCD sensor:
Active pixels (HxV):
Horizontal resolution:
Sensitivity:
Signal to noise ratio:
Gamma:
Gain:
Synchronization:
Back light compensation:
Shutter speed (fixed):
Mirror mode:
Positive/negative mode:
Iris:
Video output:
Camera Power:
Camera Power Consumption:
USB Video
Video Capture:
High Resolution Still
Image Capture:
Supported Image Formats:
Software Drivers:
USB Bandwidth:
USB Standard:
PC Minimum System
Requirements:
1/4” (6.35 mm) Sony interline CCD
768 x 494 NTSC, 752 x 582 PAL
>470 (TVL)
1 lux at 30 IRE (F1.4 AGC Max)
>48 dB
Default 0.45
Automatic or manual
Internal
Automatic or off
NTSC: Auto/Man (1/60 to 1/10000)
PAL: Auto/Man (1/50 to 1/10000)
Selectable on/off
Selectable on/off
Auto or manual
USB 1.1, USB 2.0 compliant
CVBS 1Vp-p (75ohm) & Y/C (S-Video)
12 VDC (9.0 to 15 VDC)
5.4 watts
30 fps CIF (352 x 288)
15 fps VGA (640 x 480)
NTSC: 640 x 480
320 x 240 RGB 24 Bit
PAL: 768 x 576
384 x 288 RGB 24 Bit
RGB 16, 24 bits, YUV422, YUV12
WDM streaming class driver compatible
with Direct Show & VFW
TWAIN Driver
Open Utility Software
Adjustable 0.5 Mbps to 7.5 Mbps in
0.5 Mbps increments
1.1 (USB 2.0 Compliant)
PC with a Pentium Processor 600 MHz
with MMX and 128MB of memory
USB Port
Microsoft Windows 98, ME, 2000, XP
32 bit VGA Display Adapter
Mechanical
Dimensions (WxHxD):
Lens:
Lens mount:
FOV:
Focus Range:
Zoom:
Durability:
Environmental
Ambient Operating
Temperature:
Storage Temperature:
Kit Power:
Base 10.5 x 3.2 x 11.5 in.
(267 x 83 x 292 mm)
Telescope pole 29 to 54 in.
(737 to 1372 mm)
(floor ~ center of camera)
Camera w/ lights 6.3 x 3.5 x 4.5 in.
(159 x 89 x 114 mm)
F1.4 to 2.8, FL=4.0 to 64.0
Integrated
H= 47° (wide), 3° (tele)
Infinity~1.0m (tele) to 0.01m (wide)
Optical to 16 x, Digital to 128 x
Zoom, Focus & Iris: more than 500K
cycles at room temperature
Credential
Specifications
14° to 131° F (-10° C to 55° C)
-4° to 140° F (-20° C to 60° C)
90 VAC to 240 VAC 50/60 Hz
Auto-sensing
24 watts
50
Video Recorders for OnGuard VideoManager™
DVC-ST Chassis (4U)
Overview
Lenel offers several powerful and easy-to-use video recording options for a multitude of digital
video recorder and network video recorder applications. With flexibility to meet needs ranging from
high-resolution to expansive online storage, Video Recorders from Lenel present many affordable
options for those considering upgrading an existing analog installation to those looking for a fresh,
network-centric solution. Video Recorders are available in stand-alone or integrated deployments.
OnGuard GO! configurations provide powerful stand-alone systems for customers needing a DVR
or NVR application. Additionally, OnGuard GO! customers can add access control and ID badging
DVR / GO!
to the stand-alone video recorder without needing an additional server or database! No matter the
application, Video Recorders from Lenel offer a powerful opportunity to address a critical staple in
any security program.
DVC-EX Chassis (3U)
Video Boards (DVB-408 & DVB-444)
Lenel offers two video boards, the DVB-408 and the DVB-444. Each board supports
industry-leading MPEG-4 recording compression. The affordable DVB-408 has eight channels of
capacity, while the DVB-444 has four channels and includes four on-board processors for more
efficient compression. Both board options give customers the ability to start and expand robust
video systems.
DVR / NVR / GO!
DVC-ST (4U)
Video
The DVC-ST is a reliable, rack-mountable digital video recorder with several recording and storage
options. The DVC-ST supports analog video recording with up to two DVB-408s, or up to two
DVB-444s. Each DVC-ST has three hard drive bays for SATA, allowing customers to expand to
greater than one terabyte of online storage. The DVC-ST includes a 4U, 19-inch rack mount digital
storage recorder with Windows XP Professional, 10/100/1000 Ethernet, one 80 GB internal
OS-only hard drive (optional 3 additional data hard drives), DVD/CD ROM, 1.44 floppy and mouse.
DVC-EX (3U)
The DVC-EX is a high-powered machine offering the most expansive storage capacity of any DVR
available. With eight hard drive bays, the DVC-EX has capacity for four terabytes of online
storage. In addition to storage, the DVC-EX also allows the customer to configure RAID 5 data
redundancy. The DVC-EX includes a 3U, 19-inch rack mount digital storage recorder with
Windows XP Professional, 10/100/1000 Ethernet, one 80 GB OS-hard drive (optional data hard
drives, maximum of eight), DVD/CD ROM, 1.44 floppy, mouse and rack mount rail.
51
DVC-ES
DVC-ES Chassis
The DVC-ES is an entry-level solution that is a great fit for small DVR applications. Available with a
single DVB-408, the DVC-ES comes in a tower form factor for easy placement in any security
office. It includes a tower chassis, digital storage recorder with Windows XP Professional,
10/100/1000 Ethernet, one 80 GB internal OS-only hard drive (optional 2 additional data hard
drives), CD ROM, 1.44 floppy and mouse.
DVC-1U
DVR
The DVC-1U is a powerful and easy to use Network Video Recorder (NVR) with a small footprint.
Occupying 1/4 to 1/3 the space of traditional video recorders, the 1U form factor can easily fit in
empty rack slots, rarely requiring additional racks to house it. The DVC-1U includes a 1U
DVC-1U
rack-mount chassis, digital storage recorder with Windows XP Professional, two 10/100/1000
Ethernet ports, one 80 GB internal OS-only hard drive, one 500 GB internal Data Storage Drive
(optional 2 additional data hard drives), and CD/RW-DVD/R.
DVC-DELL
The DVC-DELL features a trusted hardware standard supporting an entry-level NVR application.
The Dell solution offers IT-centric security operations the ability to develop a video program using
a factory-tested server configuration that optimizes performance and ensures reliability.
Video
Stand-alone Video Recorders - OnGuard GO!
(DVC-ST, DVC-EX & DVC-1U)
NVR / GO!
DVC-DELL
Customers looking for stand-alone digital video recorders can use a Lenel video recorder with the
OnGuard GO! configurations. The stand-alone video recorder’s OnGuard GO! configuration has
the administration applications and database on the video recorder, saving money by not requiring
a separate security server to launch the most powerful security system available. Furthermore,
customers can take the single stand-alone video recorder and add OnGuard’s robust Access
Control, Fire & Intrusion and ID Management applications, as well as countless software options.
For customers expanding an existing analog environment by upgrading to a DVR or by embracing
IP by migrating to network video, Lenel video recorders offer the flexibility to initiate an integrated
NVR / GO!
security architecture by focusing on stand-alone digital video, then expanding the system when the
time is right.
52
Fixed Dome Digital Network Camera
ICT 220 DN Plus
Full D1 resolution with a true de-interlaced filter produces brilliant, artifact-free video. Using
state-of-the-art MPEG-4 (video) and synchronized ADPCM (audio) encoding, the ICT 220 provides
superior video quality and improved network performance. The ICT 220 outperforms the
competition, when compared to other network cameras using still picture encoding technology
such as MJPEG or Wavelet. The ICT 220 utilizes superior cross bit rate encoding technology, ixBR
Control®, to deliver powerful bandwidth control. Using ixBR, digital video streams more fluidly
because the data is encoded and streamed at a constant rate, yet it retains all the rich data of
variable bit rate encoding!
Key Features
■ 3 Axis MiniDome (360° horizontal x 90° vertical)
■ Powerful MPEG-4 video compression
• Supports up to 30 frames per second at full D1 resolution
■ True de-interlaced filter
■ Bidirectional G.711 and G.726 audio communication
■ Synchronized full-duplex one channel audio and video
■ State-of-the-art CPU, separate codec and embedded software
■ Intelligent bit rate control (flexible for difficult network environments)
■ Embedded streaming server and embedded Web server
Video
■ Motion-detected and event-triggered alarm processing
■ Sensor-triggered recording and FTP:
• One (1) alarm input
• One (1) relay output
■ Supports a wide range of network protocols
■ 1/3 in. (8 mm) Sony Super HAD CCD
• 410K CCD Day-Night with IR cut filter varifocal lens
• 410K CCD standard varifocal lens
• 270K CCD fixed lens
■ True Day-Night capability
■ System time management
• RTC with Time Server synchronization
■ Security support:
• User authentication
• 128-bit encrypted data stream (selectable, for added security)
53
ICT 220 DN Plus
Resolution
Power and Ethernet
■ NTSC: 30 fps
■ NTSC: 704x480 / 352x240 / 176x144
■ Power supply input voltage: 100~250 VAC 50-60 Hz
■ PAL: 25 fps
■ PAL: 704x576 / 352x288 / 176x144
■ Power supply output voltage: 12 VAC @ 3.3 A
■ AC power cable capacity: 250 VAC, 10~16 A
Certifications
■ Camera power input: 7~23V DC Max 8 Watts
■ UL
■ CE
■ Mid span PoE injector power input: 12V DC 1 Amp
■ ULC
■ CCC
■ Power supply connector type: N (male)
■ FCC
■ RoHS
■ Ethernet: 10/100Base-T autosensing
RCA Analog Display Cable
Package Contents
RCA analog cable is for analog video output from camera module
■ Camera
inside of network camera. Use with handheld video monitor for quick
■ Power supply
and easy focus and field of view setup. Connects to video output.
■ Type N male power connector with leads
■ Single port mid span PoE injector
■ Power cords
■ CD-ROM with software & user guide
■ RCA analog display cable
■ Install template and mounting screws
Camera Dimensions
Video
■ 5.6 x 5 in. (142 mm x 128 mm)
Part Number by Model and Region
Region
Model – ICT220 DN Plus
( 410KCCD- Day-Night)
Model- ICT220S
(410KCCD )
Model- ICT220S
( 270KCCD )
Americas- Asia Pacific
ICT2201DN
ICT2201S
ICT2201
Australia
ICT2202DN
ICT2202S
ICT2202
UK
ICT2203DN
ICT2203S
ICT2203
Europe
ICT2204DN
ICT2204S
ICT2204
Lens
Model
Lens
Minimum Illumination (Lux)
ICT220DN Plus
Varifocal 4.0 – 9.0 mm F1.2
0.1Lux / f=1.4 (AGC 0n)
ICT220S
Varifocal 4.0 – 9.0 mm F1.2
0.1Lux / f=1.4 (AGC 0n)
ICT220
Fixed 3.8 mm F2.0 manual focus
0.3Lux
54
Digital Network Camera
ICT 230 DN Plus
Full D1 resolution with a true de-interlaced filter produces brilliant, artifact-free video. Using
state-of-the-art MPEG-4 (video) and synchronized ADPCM (audio) encoding, the ICT 230 provides
superior video quality and improved network performance. The ICT 230 outperforms the
competition, when compared to other network cameras using still picture encoding technology
such as MJPEG or Wavelet. The ICT 230 utilizes superior cross bit rate encoding technology, ixBR
Control®, to deliver powerful bandwidth control. Using ixBR, digital video streams more fluidly
because the data is encoded and streamed at a constant rate, yet it retains all the rich data of
variable bit rate encoding!
Key Features
■ Powerful MPEG-4 video compression
• Supports up to 30 frames per second at full D1 resolution
■ True de-interlaced filter
■ Bidirectional G.711 and G.726 audio communication
■ Synchronized full-duplex one channel audio and video
■ State-of-the-art CPU, separate codec and embedded software
■ Intelligent bit rate control (flexible for difficult network environments)
■ Embedded streaming server and embedded Web server
■ Motion-detected and event-triggered alarm processing
Video
■ Sensor-triggered recording & FTP:
• One (1) alarm input
• One (1) relay output
■ Supports a wide range of network protocols
■ 1/3 in. (8 mm) Sony Super HAD CCD
• 410K CCD
• 270K CCD
■ True Day-Night capability
■ RoHS-compliant product
■ System time management
• RTC with Time Server synchronization
■ Security support:
• User authentication
• 128-bit encrypted data stream (selectable, for added security)
■ Lens not included
55
ICT 230 DN Plus
Resolution
Power and Ethernet
■ NTSC: 30 fps
■ Power supply input voltage: 100~250 VAC 50-60 Hz
■ PAL: 25 fps
■ Power supply output voltage: 12 VAC @ 3.3 A
■ NTSC: 704x480 / 352x240 / 176x144
■ AC power cable capacity: 250 VAC, 10~16 A
■ PAL: 704x576 / 352x288 / 176x144
■ Camera power input: 7~23V DC Max 8 Watts
■ Minimum Illumination 0.1 LUX / F=1.4 (AGC-on)
■ Mid span PoE injector power input: 12V DC 1 Amp
■ Power supply connector type: N (male)
■ Ethernet: 10/100Base-T autosensing
Certifications
Package Contents
■ UL
■ Camera
■ ULC
■ Power supply
■ FCC
■ Single port mid span POE injector
■ CE
■ Power cords
■ CCC
■ CD-ROM with software and user guide
■ RoHS
■ Mounting stand
■ Type N Power connector with leads
Camera Dimensions (without lens)
Video
■ 5.3 x 2.4 x 2.2 in. (135 x 60 x 57 mm)
Environment
Part Number by Model and Region
■ Recommendation: For indoor use unless in housing
Region
Model – ICT230 DN
( 410KCCD- Day-Night)
Model- ICT230S
( 270KCCD )
■ 21~65 °F (-4~140 °C) Endurable
Americas- Asia Pacific
ICT2201DN
ICT2201S
Humidity
Australia
ICT2202DN
ICT2202S
■ 8~80% RH Optimum
UK
ICT2203DN
ICT2203S
■ 0~90% RH Endurable
Europe
ICT2204DN
ICT2204S
Temperature
■ 41~122 °F (5~50 °C) Optimum
56
Outdoor IP Digital Speed Dome
ICT 240 DN
The ICT 240 is a full-featured IP speed dome that delivers the best of both worlds: performance
and affordability. This outdoor speed dome provides full D1 resolution (704X480 NTSC, 704X576
PAL) with a true de-interlaced filter that produces immaculate video. Stealth Spin Technology®
uses precisely machined gears, delivering unmatched smooth and accurate movement for virtually
silent operation. Using state-of-the-art MPEG-4 (video) and synchronized ADPCM (audio)
encoding, the ICT 240 provides superior video quality and improved network performance. The
ICT 240 outperforms the competition, when compared to other network cameras using still picture
encoding technology such as MJPEG or Wavelet. The ICT 240 uses ixBR® superior cross bit rate
encoding technology. Using ixBR, digital video streams more fluidly because the data is encoded
and streamed at a constant rate, yet it retains all the data of variable bit rate encoding!
Built for maximum long-life performance, the ICT 240 deploys a high-quality slip-ring, tested for
over 20 million spins!
Key Features
■ Extremely silent, outdoor speed dome IP camera
■ 1/4 in. Sony Ex-view CCD
■ Filter changeable type day and night
■ IP66 water-resistant
■ 26X optical with 12X digital zoom (selectable)
• Optional: 18X optical with 12X digital zoom
Video
■ State-of-the-art CPU, codec and embedded software
■ Superior video compression – MPEG-4
■ Maximum 30 frames per second at D1 resolution with de-interlaced filter
■ Bidirectional audio communication – up (ADPCM), down (PCM)
■ Synchronized one channel audio and video data transmission
■ Intelligent bit rate control for flexible network deployment
■ Enhanced image quality
■ MPEG-4
■ Embedded streaming server and embedded Web server
■ Motion-detected and event-triggered alarm processing
■ Easy recording and playback on client PC
■ Sensor-triggered
• Four (4) alarm inputs
• Two (2) relay outputs
■ Auto-flip video – on/off configuration
■ Wide range of network protocols supported
■ System time management
• RTC with Time Server synchronization
■ Security support
• User authentication
• 128-bit encrypted streaming data for additional security (selectable)
57
ICT 240 DN
Resolution
Power and Ethernet
■ NTSC: 30 fps
■ PS input voltage: 100~250 VAC 50-60 Hz
■ PAL: 25 fps
■ PS output : 18-32 VAC @ 1.3 A
■ NTSC: 768x494
■ AC power cable: 250 VAC, 10~16 A
■ PAL: 752x582
■ Power consumption: 24 watts maximum
■ Horizontal Resolution: >480 TVL
■ Ethernet: 100Base-T
Certifications
Package Contents
■ UL
■ Camera
■ FCC
■ External housing (IP66)
■ CE
■ Wall mount and hardware
■ CCC
■ CD-ROM with Software & User Guide
■ RoHS
■ Quick Installation Guide
Environment
Weight
Temperature
■ 5 lbs (1.9 kg)
■ 41~60 °F (5~50 °C) Optimum
■ -4~140 °F (-20~60 °C) Endurable
Pan Tilt
Humidity
■ Pan: 350° per second continuous rotation
■ 8~80% RH Optimum
■ Tilt Rotation: 0-90°
■ 0~90% RH Endurable
■ Accuracy: 0.024°
Video Quality
Privacy Zones and Sectors
■ Minimum luminance – Normal: 0.7 lux
■ 24 programmable zones
■ Minimum luminance – Night Mode: 0.1 lux
■ 8 programmable sector patterns
Video
■ ULC
■ Day-Night ICR: Auto/Day/Night
■ Luminance Signal-to-Noise Ratio: >50 dB
■ BLC: On/Off
Lens
■ f1.6~3.8 f3.5-91.0 mm
■ Minimum video distance: .32 m (w) / 4.92 ft. (1.5 m) telephoto
58
Indoor IP Digital Speed Dome
ICT 250 DN
The ICT 250 is a full-featured IP speed dome that delivers the best of both worlds: performance
and affordability. This indoor speed dome provides full D1 resolution (704X480 NTSC, 704X576
PAL) with a true de-interlaced filter that produces immaculate video. Stealth Spin Technology®
uses precisely machined gears, delivering unmatched smooth and accurate movement for virtually
silent operation. Using state-of-the-art MPEG-4 (video) and synchronized ADPCM (audio)
encoding, the ICT 250 provides superior video quality and improved network performance. The
ICT 250 outperforms the competition, when compared to other network cameras using still picture
encoding technology such as MJPEG or Wavelet. The ICT 250 uses ixBR® superior cross bit rate
encoding technology. Using ixBR, digital video streams more fluidly because the data is encoded
and streamed at a constant rate, yet it retains all the data of variable bit rate encoding!
Built for maximum long-life performance, the ICT 250 deploys a high-quality slip-ring, tested for
over 20 million spins!
Key Features
■ Stealth Spin Rotation technology
■ 1/4 in. Sony Ex-view CCD
■ Filter changeable type day and night
■ 26X optical with 12X digital zoom (selectable)
• Optional 18X optical zoom with 12X digital zoom
Video
■ State-of-the-art CPU, codec and embedded software
■ Superior video compression – MPEG-4
■ Maximum 30 frames per second at D1 resolution with de-interlaced filter
■ Bidirectional audio communication – up (ADPCM), down (PCM)
■ Synchronized one channel audio and video data transmission
■ Intelligent bit rate control for flexible network deployment
■ Enhanced image quality
■ MPEG-4
■ Embedded streaming server and embedded Web server
■ Motion-detected and event-triggered alarm processing
■ Easy recording and playback on client PC
■ Sensor-triggered
• Four (4) alarm inputs
• Two (2) relay outputs
■ Auto-flip video – on/off configuration
■ Wide range of network protocols supported
■ System time management
• RTC with Time Server synchronization
■ Security support
• User authentication
• 128-bit encrypted streaming data for additional security (selectable)
59
ICT 250 DN
Resolution
Power and Ethernet
■ NTSC: 30 fps
■ PS input voltage: 100~250 VAC 50-60 Hz
■ PAL: 25 fps
■ PS output : 18-32 VAC @ 1.3 A
■ NTSC: 768x494
■ AC power cable: 250 VAC, 10~16 A
■ PAL: 752x582
■ Power consumption: 24 watts maximum
■ Horizontal resolution: >480 TVL
■ Ethernet: 100Base-T
Certifications
Package Contents
■ UL
■ Camera
■ FCC
■ Ceiling mount bracket and cover
■ CE
■ CD-ROM with Software & User Guide
■ CCC
■ RoHS
Environment
Weight
Temperature
■ 5 lbs (1.9 kg)
■ 41~122 °F (5~50 °C ) Optimum
■ -4~140 °F (-20~60 °C) Endurable
Pan Tilt
Humidity
■ Pan: 350° per second continuous rotation
■ 8~80% RH Optimum
■ Tilt rotation: 0-90°
■ 0~90% RH Endurable
■ Accuracy: 0.024°
Video Quality
Privacy Zones and Sectors
■ Minimum luminance – Normal: 0.7 lux
■ 24 programmable zones
■ Minimum luminance – Night Mode: 0.1 lux
■ 8 programmable sector patterns
Video
■ ULC
■ Day-Night ICR: Auto/Day-Night
■ Luminance Signal-to-Noise Ratio: >50 dB
■ BLC: On/Off
Lens
■ f1.6~3.8 f3.5-91.0 mm
■ Minimum video distance: .32 m (w) / 4.92 ft. (1.5 m) telephoto
60
Single Channel AV Server
ICT 510 Video Server
The ICT 510 single channel audio/video server supports full D1 resolution coupled with a true
de-interlaced filter to produce brilliant, artifact-free video. Owing to state-of-the-art MPEG-4 (video)
and synchronized ADPCM (audio) encoding, the ICT 510 provides superior video quality and
improved network performance. The ICT 510 outperforms the competition, when compared with
other audio video server using still picture encoding technology such as MJPEG or Wavelet. The
ICT 510 provides superior cross bit rate encoding technology, ixBR Control®, which delivers
powerful bandwidth control. Using ixBR, digital video streams more fluidly because the data is
encoded and streamed at a constant rate, yet it retains all the rich data of variable bit rate
encoding!
Key Features
■ MPEG-4 video compression
■ Supports video frame rates of up to 30 fps
■ Full D1 resolution with de-interlaced filter
■ Bidirectional G7.11 audio communication
■ Synchronized one channel audio and video data transmission
■ Intelligent bit rate control for various network environments
■ Enhanced image quality
■ MPEG-4 and JPEG dual streaming for mobile network
Video
■ Embedded streaming server
■ Embedded Web server
■ Motion-detected and event-triggered alarm processing
■ Remote PTZ control via RS-485
■ Sensor-triggered one alarm input and one relay output
■ Wide range of network protocols supported
■ System time management
• RTC with Time Server synchronization
■ Security support
• User authentication
• Encrypted streaming data for additional security (selectable)
61
ICT 510 Video Server
Resolution
Power and Ethernet
■ NTSC: 30 fps
■ PS input voltage: 100~250 VAC 50-60 Hz
■ PAL: 25 fps
■ PS output : +12 V @ 1.3 A
■ NTSC: 704x480, 356x240, 176x120
■ Server input: 7~23 VAC
■ PAL: 704x576, 352x288, 176x144
■ AC power cable: 250 VAC, 10~16 A
■ Power consumption: 8 watts maximum
Certifications
Package Contents
■ UL
■ Server
■ FCC
■ Regional specific power supply
■ CE
■ Power cords
■ CCC
■ CD-ROM with Software & User Guide
■ RoHS
■ Mid span POE injector
■ ULC
■ Type N Power connector with leads
Environment (indoor use only)
PC Requirement Remote Viewing (minimum)
Temperature
■ P-4 1.2 GHz Processor
■ 41~122 °F (5~50 °C) Optimum
■ 256 MB RAM
■ -4~140 °F (-20~60 °C) Endurable
■ Windows 2000, Windows XP Professional / Home
Humidity
■ IE 5.5
■ 8~80% RH Optimum
■ Video monitor minimum resolution: 1024 x 768
■ 0~90% RH Endurable
■ Ethernet: 100Base-T
Video
■ Ethernet: 10/100Base-T autosensing
62
63
Contact Information
Lenel Systems International is a leading provider of software and
With nearly 15,000 system installations in 90 countries worldwide, we
turnkey security systems for corporate and government markets. We
boast a blue chip customer base with a strong presence in a broad
focus on developing products that enable organizations to effectively
range of vertical markets. We have earned numerous awards for
protect and manage their people, property and assets by maximizing IT
technology innovation, growth, market leadership and customer
and infrastructure investments.
satisfaction. Lenel is part of UTC Fire & Security, a business unit of
United Technologies Corp. (NYSE:UTX).
When we launched the OnGuard integrated solution in 1995, our
pioneering efforts brought the power of leading-edge technology, the
Lenel’s world headquarters are located in Rochester, New York. We
reliability of software industry standards, and the flexibility of open
also have major operational centers in London, Hong Kong, Beirut and
systems architecture to a historically proprietary security market. We
Dubai, numerous satellite offices, and sales and support coverage
swiftly moved to a leadership position by developing and delivering
worldwide.
business solutions that protect people, property and assets. Today we
are recognized as the global leader and de facto standard in software
and integrated systems for commercial and government security
markets.
Corporate Headquarters
1212 Pittsford-Victor Road
Pittsford, NY 14534-3820
TEL: 585.248.9720
FAX: 585.248.9185
United Kingdom Office & Training Center
Hong Kong Office & Training Center
95 Maybury Road
Room 1401-2, 14/F
Woking, Surrey
Chinachem Johnston Plaza
GU21 5JL UK
178-186 Johnston Plaza
TEL: +44.1483.815230
Wanchai, Hong Kong, SAR, China
FAX: +44.1483.815231
TEL: +852.2893.2886
FAX: +852.2893.7373
Dubai Office & Training Center
Middle East Office & Training Center
Building 5EB - Office 550
Assaydeh Center, Main Road
Dubai Airport Free Zone
Mansourieh, Al Matn
Dubai, UAE
Lebanon
TEL: +971.4.609.1019
TEL: +961.4.409184
FAX: +971.4.609.1021
FAX: +961.4.409569
64
Lenel is a global leader in the development and delivery of scalable, integrated systems for
the commercial security market, with over 15,000 system implementations in more than 90
countries. Lenel is headquartered in Rochester, N.Y. USA, with sales and support coverage
in all major world markets. Lenel is part of UTC Fire & Security, a $4.7 billion company that
provides fire safety and security solutions to more than one million customers worldwide.
Headquartered in Connecticut, UTC Fire & Security is a business unit of United Technologies
Corp., which provides high technology products and services to the building and aerospace
industries worldwide. More information about Lenel and UTC Fire & Security can be found on
their Web sites at http://www.lenel.com and http://www.utcfireandsecurity.com.
The possibilities are endless.
www.lenel.com
Lenel Systems International, Inc.
1212 Pittsford-Victor Road
Pittsford, New York 14534 USA
Tel 585.248.9720 Fax 585.248.9185
www.lenel.com
© 2007 Lenel Systems International, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement