Fluval FX5 Canister Filter Instruction manual

64&3."/6"(6*%&
%&-µ65*-*4"5&63
#&/65;&3)"/%#6$)
."/6"-
%&*/4536$$*0/&4
FLUVAL '9
£
Î
Ó
{
>
L
V
Ç
n
£ä
È
™
££
x
£{
£Î
£Ó
PRODUCT PARTS
1 Hosing
8 AquaStop valves (3)
2 Rim connectors (2)
9 Filter lid
3 Rim connector clips (6)
10 Lid fasteners (8)
4 Small suction cups (4)
11 Filter canister
5 Intake assembly
12 Purge valve
6 Output assembly
13 Drain cap
7 Metal clamps (2)
14 Pump unit & power cord
Filter baskets with
foam inserts
a Foam (6)
b T handles (2)
c Media baskets (3)
PIÈCES DE L’APPAREIL
2 Raccords des tuyaux
au cadre (2)
7 Colliers de serrage
en métal (2)
14 Pompe et cordon
d’alimentation
8 Soupapes AquaStop (3)
3 Pinces pour raccords des
tuyaux au cadre (6)
9 Couvercle du filtre
Paniers de filtration
avec blocs de mousse
1 Tuyau
4 Petites ventouses (4)
5 Bloc d’entrée d’eau
6 Bloc de sortie d’eau
10 Fermoirs du couvercle (8)
11 Boîtier du filtre
12 Soupape d’évacuation
a Mousse (6)
b Poignées en T (2)
c Paniers de filtration (3)
13 Bouchon de vidange
PRODUKTTEILE
1 Schlauch
7 Metallklemmen (2)
2 Rahmenbefestigungssätze (2)
8 AquaStop-Ventile (3)
3 Rahmenbefestigungsclips (6)
10 Deckelschrauben (8)
9 Filterdeckel
4 Kleine Saugnäpfe (4)
11 Filterbehälter
5 Ansaugverbindung
12 Ablaufventil
6 Wasseraustrittsverbindung
13 Abflusskappe
14 Pumpeneinheit und
Netzkabel
Filterkörbe mit
Schaumstoffpatronen
a Schaumstoff (6)
b T-Griffe (2)
c Medienkörbe (3)
Piezas del PRODUCTO
1 Tubos
8 Válvulas AquaStop (3)
2 Salvatubos (2)
9 Tapa del filtro
3 Clips de salvatubos (6)
10 Cierres de la tapa (8)
4 Ventosas pequeñas (4)
11 Vaso
5 Conjunto de entrada
12 Válvula de vaciado
6 Conjunto de salida
13 Tapa de goma de vaciado
7 Abrazaderas metálicas (2)
14 Unidad de bomba y cable
de alimentación
Cestas de filtro con
espumas
a Espuma (6)
b Asas en T (2)
c Cestas de medios
filtrantes (3)
Table of Contents
Inhaltsverzeichnis
Safeguard Instructions ....................................EN-1
Sicherheitshinweise .........................................DE-1
Introduction.....................................................EN-2
Einleitung ........................................................DE-2
State of the Art Technology ...........................EN-3
Fluval – Modernste Technologie ....................DE-3
Installation & Use ............................................EN-5
Montage und Inbetriebnahme .....................DE-5
Fluval Advanced Filtration............................EN-13
Die innovative Fluval Filterung ....................DE-13
Fluval Filter Media ........................................EN-14
Auswahl an Fluval Filtermedien...................DE-14
Fluval Lab Series Media ................................EN-16
Fluval Lab Series Filtermedien......................DE-16
Maintenance
Wartung
Canister Draining
Entleerung des Filterbehälters
Purge valve Draining .........................EN-17
Entleerung per Ablaufventil .............DE-17
Filter Pump Draining..........................EN-18
Entleerung per Filterpumpe ..............DE-18
Media Care ...............................................EN-19
Filtermaterialpflege.................................DE-19
Purge Valve ..............................................EN-20
Ablaufventil .............................................DE-20
Pump Care ................................................EN-22
Pumpenpflege..........................................DE-22
Changing Aquarium Water.....................EN-23
Wasserwechsel .........................................DE-23
Replacement Parts.........................................EN-24
Ersatzteile ......................................................DE-24
Table des matières
Tabla de Materias
Mesures de sécurité .........................................FR-1
Instrucciones de seguridad ..............................ES-1
Introduction .....................................................FR-2
Introducción .....................................................ES-2
Technologie avancée Fluval ............................FR-3
Tecnología de vanguardia ...............................ES-3
Installation et utilisation .................................FR-5
Instalación y uso..............................................ES-5
Filtration avancée Fluval ...............................FR-13
Filtración avanzada Fluval .............................ES-13
Masses filtrantes Fluval .................................FR-14
Medios filtrantes Fluval .................................ES-14
Masses filtrantes Fluval Lab Series................FR-16
Medios de la Serie Lab de Fluval ..................ES-16
Entretien
Mantenimiento
Drainage du boîtier
Vaciado del vaso
Drainage de la soupape
Vaciado con la válvula de vaciado .....ES-17
d’évacuation........................................FR-17
Vaciado con la bomba del filtro ........ES-18
Drainage de la pompe-filtre ..............FR-18
Cuidados de los medios filtrantes ...........ES-19
Entretien des masses filtrantes................FR-19
Válvula de vaciado ...................................ES-20
Soupape d’évacuation .............................FR-20
Cuidados de la bomba .............................ES-22
Entretien de la pompe .............................FR-22
Cambio del agua del acuario...................ES-23
Changement de l’eau d’aquarium ..........FR-23
Piezas de repuesto .........................................ES-24
Pièces de rechange ........................................FR-24
IMPORTANT SAFETY INSTRUCTIONS
WARNING - To guard against injury, basic safety precautions should be observed.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
To guard against injury, basic safety precautions should be observed
when handling the Fluval Canister Filter, including the following:
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS
and all the important notices on the appliance before
using. Failure to do so may result in damage to the unit.
3. Close supervision is necessary when any appliance is
used by or near children.
4. To avoid injury, do not touch moving parts or hot parts.
5. CAUTION – Always unplug or disconnect all appliances
in the aquarium from electricity supply before placing
hands in water, before putting on or taking off parts
and whilst the equipment is being installed,
maintained or handled. Never yank cord to pull plug
from outlet. Grasp the plug and pull to disconnect.
Always unplug an appliance from an outlet when not
in use.
2. DANGER - To avoid possible electric shock, special care
should be taken since water is employed in the use of
aquarium equipment. For each of the following
situations, do not attempt repairs yourself; return the
appliance to an authorized service facility for service or
discard the appliance.
A. If the appliance falls into the water, DON’T reach for
it! First unplug it and retrieve it. If electrical
components of the appliance get wet, unplug the
appliance immediately.
B. If the appliance shows any sign of abnormal water
leakage or if RCD (or GFCI- Ground Fault Current
Interrupter) switches off disconnect the power
supply cord from mains and remove pump from water.
6. This is an aquarium filter-pump. Do not use this filterpump for other than intended use (i.e.: do not use in
swimming pools, bathrooms, etc.). The use of
attachments not recommended or sold by the
appliance manufacturer may cause an unsafe
condition.
• Do not use this filter-pump in swimming pools or
other situations where people are immersed.
C. Carefully examine the appliance after installation. It
should not be plugged if there is water on parts not
intended to be wet.
D. Do not operate any appliance if it has a damaged
cord or plug, or if it is malfunctioning or it is
dropped or damaged in any manner. The power cord
of this appliance cannot be replaced; if the cord is
damaged, the appliance should be discarded. Never
cut the cord.
E. To avoid the possibility of the appliance plug or
receptacle getting wet, position the appliance to one
side of a wall mounted receptacle to prevent water
from dripping onto the receptacle or plug. A “drip
loop” (see illustration 1) should be arranged by the
user for the cord connecting appliance to a
receptacle. The “drip loop” is that part of the cord
below the level of the receptacle or the connector if
an extension cord is used, to prevent water traveling
along the cord and coming in contact with the
receptacle.
If the plug or receptacle
does get wet, DON’T
unplug the cord. Disconnect
the fuse or circuit breaker
that supplies power to the
appliance. Then unplug and
examine for presence of water in receptacle.
• This filter-pump is suitable for use in water
temperatures up to 35 °C.
• Do not use this filter-pump with inflammable or
drinkable liquids.
7. This filter-pump is suitable for INDOOR use only. Do not
install or store the appliance where it will be exposed
to the weather or to temperatures below freezing.
8. Make sure that the filter-pump is securely installed
before operating it. Do not allow pump to run dry.
9. If an extension cord is necessary, a cord with proper
rating should be used. A cord rated for less amperes
or watts than the appliance rating may overheat. Care
should be taken to arrange the cord so that it will not
be tripped over or pulled. The connection should be
carried out by a qualified electrical installer.
10.
EN-1
SAVE THESE INSTRUCTIONS
For the complete use and understanding of this
product it is recommended that this manual is
thoroughly read and understood. Failure to do so
may result in damage to this product.
HIGH PERFORMANCE CANISTER FILTER
The Fluval Canister Filter offers unparalleled
filtration power, maximum versatility and
incredible control in fine-tuning water
characteristics. Our multi-stage system allows
you to stack filtration media in the precise
combination of layers that will work best for
your aquarium. Thus providing you infinite
flexibility in creating and maintaining the ideal
environment for your fish.
Its massive capacity and powerful integrated
motor processes and recirculates fully 607 US
gallons (2300 liters) of water every hour,
enabling you to precisely manage water
conditions for aquariums as large as 400 US
gallons (1500 liters). It will hold up to 1.5 gallons
(5.9 liters) of media, yet it’s compact enough to
fit under almost any aquarium cabinet.
With Fluval’s unique Smart-Pump Technology,
this self-priming system offers plug-in-and-start
convenience. Upon start-up the canister fills
with water, pauses to evacuate air, immediately
begins the filtering process, and continues
filtering until it is unplugged. Once every 24
hours, the filter will pause again to evacuate
any air that has become trapped in the
system–to maintain the total vacuum necessary
for maximum efficiency.
The FX5’s stack of media baskets allow multiple
options to modify water with scientific
precision. Use one type of media in each basket,
or layer two or three types to suit your
aquarium’s needs.
The FX5 Filter also offers incomparable ease-ofuse features: click-fit connections you just push
on; AquaStop valves so you can handle routine
maintenance without breaking the system’s
vacuum, no need to disassemble hosing;
innovative handles that let you lift the entire
stack of baskets out to change or clean media;
and a purge valve and extra Aquastop Valve so
you can empty the canister easily, no need to
move or lift a heavy, water-laden tank.
This filter’s superior performance and capability
are backed by Fluval’s well-earned reputation
for the best in fish and aquarium care. HARS
(Hagen Aquatic Research Station) certification is
your assurance of the most up-to-date and
reliable research in aqua-care science.
For complete understanding of your Fluval
Multi-Stage Canister Filter, and enjoyment of all
its capabilities, please read and follow these
instructions for proper installation, maintenance,
and use. Failure to do so may result in loss of
fish life and/or damage to the filter. SAVE THESE
INSTRUCTIONS FOR FUTURE REFERENCE.
SYSTEM OVERVIEW
The FX-5 filter siphons water and suspended
debris in through its clog-proof intake strainer,
then sends it through three levels of foam,
which traps most particulate matter. The
powerful pump then sends it through the
multiple levels of media for whatever cleaning
and processing sequence you have chosen.
As water flows back into the aquarium, the
flared design of the adjustable output nozzle
disperses it in multiple directions, agitating the
water and creating currents that help break
down wastes, and prevent them from settling.
All for a continuous flow of pure, precisely
treated water.
EN-2
FLUVAL STATE-OF-THE ART TECHNOLOGY
AquaStop Valves
The AquaStop valve makes maintenance easy by allowing you to
stop the water flow with an easy 90-degree turn of the valve
lever. This means you can separate the hosing from the filter in
one step. The valve lever can also be used to regulate water flow
with no harm to the motor or its components. Three Valves are
provided; one for the intake, one for the output and one to be
used to drain the filter under certain circumstances during the
maintenance process.
Click-fit Connectors
Click-fit connectors are designed for quick set-up and leak-proof
maintenance. You just push the intake and output assemblies
(Aquastop valves and attached hosing) down. Once you hear the
“click,” you know the connection is secure and watertight.
Lift-Out Stack of Media Baskets
The lift-out stack of media baskets is at the heart of Fluval multistage filtration. These large capacity baskets enable you to stack
filtration media in the precise combination of layers that will
work best for your aquarium. Each basket is lined with a foam
insert for effective mechanical pre-filtering. The instant-release
T-handles let you lift, then separate the basket stack quickly and
easily, making routine maintenance simple.
High Capacity Canister
The FX5’s compact, super capacity tank processes and recirculates
fully 607 US gallons (2300 liters) of water every hour and
accommodates the stack of media baskets with their capacity
of up to 1.5 gallons (5.9 liters) of media. Yet this enormouscapacity tank is short enough (21 in./54cm) to fit under most
large aquariums.
EN-3
FLUVAL STATE-OF-THE ART TECHNOLOGY
Smart-Pump Technology
Designed and engineered for reliable filtration of delicately
balanced aquarium environments, Fluval’s FX5 SMART PUMP
technology employs an electronic circuit board to continually
monitor the pump. Impeller speed and force are constantly
measured to ensure powerful output and energy efficiency.
Self-Priming
Instant-Start
System
Smart pump technology is also critical in evacuating any air that
may build up in the system. Once every 24 hours, the filter will
pause and allow any trapped air to escape, thus maintaining
maximum filtration efficiency.
Self-Priming Instant-Start System
With the FX5, there’s never any need for manual siphoning. As
soon as you plug the filter in, the canister fills with water from
your aquarium. It pumps for 2 minutes, pauses for 2 minutes to
evacuate air from the system, then immediately begins the
filtering process.
Smart-Pump
Technology
Purge Valve
Purge Valve
The FX5 canister features a purge valve drain at its base.
This makes it possible for you to empty the canister for
maintenance before moving it.
Clog-Proof Intake Strainer
The wide, rounded mouth of the FX5 intake strainer is shaped to
siphon water quickly. Covered by a fine screen that’s beveled to
repel debris, it is virtually clog-proof, so there is never a build-up
of solids that could impede water flow.
Multi-Directional Output Nozzle
The flared spout of the adjustable output nozzle sends multiple
streams of purified water toward all corners of the aquarium,
creating currents that agitate the water to break down wastes
and help hold them in suspension until they can be drawn into
the filter by the intake strainer. With more waste solids kept
afloat, fewer settle, which means that bottom surfaces, and in
fact the entire aquarium, is kept cleaner.
FLUVAL FX5 SPECIFICATIONS
Aquarium Capacity:
400 gallons
1,500 liters
925 g/h
325.5 in.2
3,500 l/h
2,100 cm2
Biological Volume:
1.5 gallons
Filtration Volume:
5.28 gallons
Pump Output:
Mechanical Area (Foam):
Filter Circulation*:
Head Height (max.):
607 g/h
2,300 l/h
10.8ft
3.3 m
Wattages 120V/60Hz:
50W
5.9 l
Wattages 230-240V/50Hz:
48W
20 l
*Note: Flow rates were measured with intake and output
hoses of the same length and without media.
EN-4
INSTALLATION AND USE
IMPORTANT: Read all instructions before beginning.
• For best results, top off water in aquarium before beginning setup.
• Allow 45-60 minutes for setup and installation.
• Tools required: Phillips screwdriver and utility knife.
(NOTE: For an unusually shallow aquarium, the intake tube may
need to be cut; this requires a hacksaw.)
DO NOT PLUG IN FILTER UNTIL SETUP IS COMPLETE AND UNIT IS FILLED WITH WATER.
1. Unpack and identify all parts
Use the diagram on the inside front cover as a guide.
2. Prepare the aquarium
1. Decide on filter placement. Remember, this is a gravity-fed
system. For it to work properly, all the Installation
Requirements below must be adhered to.
Installation Requirements
• For best results fill aquarium to maximum level
before beginning setup.
< 20cm (7.8 in.)
• The filter lid must be at least 7.8 in. (20cm) below your
aquarium’s water level but never more than 4.9 ft. (150cm).
• The hosing supplied with the unit is 9.8 ft. (3m) long.
If longer hosing is required, intake hosing must
NOT exceed 9.8 ft. (3m) and the total length of
intake and outlet hosing combined must not
exceed 16.4 ft. (5m).
• Hosing must follow a straight path from the filter to the
aquarium rim, with some slack, but no loops.
• The water level should never be more than 7.8 in.
(20 cm)below your aquarium rim.
• NEVER install the filter above the water level.
• For best performance, the filter should be completely
beneath the aquarium.
• Position Purge Valve so that you will be able to attach a
hose without moving the unit.
EN-5
20cm (7.8 in.) to
< 150cm (4.9 ft.)
INSTALLATION AND USE
2. Place the two rim connectors over the back top edge of the aquarium. Place one just above
the spot where you want to place the intake tube; place the other just over the spot where
you want to position the output nozzle. Be sure that the long end of the bracket is on the
inside of the aquarium.
The rubber rings on the connectors are designed to help them adhere to tank glass better.
If the aquarium walls are thinner than 5/8” (1.58 cm) replace the rubber ring with the four
smaller suction cups provided.
Important: Be sure to position the intake tube away from any air source—an air stone, an
aeration device, protein skimmer or the output valve. Air entering the intake strainer will
diminish filter efficiency.
Alternate Configurations
Note: A dropped ledge rim requires purchase
of an extra rim connector. (See “Replacement Parts” for ordering information.)
EN-6
INSTALLATION AND USE
3. Prepare intake connections
1. Connect the hosing to one of the three valves:
a. Loosen one of the metal clamps, and slide it onto one
end of the hosing.
b. Push the end of the hosing onto the valve; push it all
the way, as far as it will go.
c. Position the metal clamp over the rubber connector,
and tighten.
2. Measure and cut the hosing. You will need a length of
hosing that reaches comfortably from inside the aquarium
to the filter canister.
Important: Hosing should follow a straight path from the
filter to the aquarium rim, with some slack, but no loops.
If the hosing is too long, the filter will not work efficiently.
6 in.
(15cm)
a. Place the valve end of the hosing at the approximate
spot where it will be positioned on the filter lid
(once the filter is installed).
b. Stretch out the hosing so it rests over the “intake”
rim bracket.
c. At a spot at least 6 in. (15cm) beyond the aquarium rim,
use a utility knife to cut the hosing.Do not cut it too
short. Remember, you can always cut it shorter during
final installation, if necessary.
3. Push the cut end of this “intake” hosing into the rubber
connector on the intake tube. Push the hosing in by at least
1 in. (2.5cm) without twisting it.
5
4. Place the intake strainer in the tank, making sure it is at
least 3 in. (7.5 cm) from the bottom. (If the tube is too long
for the height of your aquarium, remove the strainer, cut the
intake tube with a hacksaw, and then replace the strainer.)
Once the intake strainer is properly positioned, lock it in
place by pressing the suction cups against the glass.
5. Fasten the intake strainer’s hosing onto the rim connector
using the three rim connector clips.
3
4
EN-7
INSTALLATION AND USE
4. Prepare output connections
1. Connect the hosing to the second valve
(just as for the intake hosing):
a. Loosen the second metal clamp, and slide it onto the
factory-finished end of the hosing (not the cut end).
b. Push the end of the hosing onto the valve; push it all
the way, as far as it will go.
c. Position the metal clamp over the rubber connector,
and tighten.
2. Measure and cut the hosing. Again, you will need a length
of hosing that reaches comfortably from inside the
aquarium to the filter canister.
Reminder: Hosing should follow a straight path from the
filter to the aquarium rim, with some slack, but no loops.
If the hose is too long, the filter will not work efficiently.
6 in.
(15cm)
a. Place the valve end of the hosing at the approximate
spot where it will be positioned on the filter lid
(once the filter is installed).
b. Stretch out the hosing so it rests over the “output”
rim bracket.
c. At a spot at least 6 in. (15 cm) beyond the aquarium rim,
use a utility knife to cut the hosing. Do not cut it too
short. Remember, you can always cut it shorter during
final installation, if necessary
3. Push the cut end of this “output” hosing into the rubber
connector of the output nozzle. Push the hosing in by at
least 1 in. (2.5cm) without twisting it.
5
4. Place the nozzle in the tank about 1 in. (2.5cm)
below the water line.
5. Fasten the hosing to the “output” bracket using
the three rim connector clips.
3
4
EN-8
INSTALLATION AND USE
5. Prepare the Filter
1. Loosen and disengage the eight lid fasteners.
2. Remove the filter lid and set it aside. Be careful not to damage the inlet stem connected to
the lid.
3. Using the orange T-handles, lift the three media baskets from the filter canister.
The T-handles will fall outward so the baskets can be handled separately.
Foam Insert
T-handle
Media Basket
4. Rinse the media baskets and foam inserts under running
tap water to remove any dust particles.
5. Replace the foam inserts, and fill the center of each
basket with filtering media (Media not included. See
“About Media” for detailed descriptions of all media
available from Fluval). Leave at least 0.5 in. (1cm) free space
on top of the media, so the baskets will fit together properly.
6. Stack the baskets, carefully aligning them, so that all
shapes match. Reinsert the T-handles into their vertical
slots, and replace the baskets in the filter canister. The
foam in the upper basket should be just about even with
the top edge of the canister (the output tube, which is
affixed to the inside of the canister, will be protruding
slightly).
EN-9
>0.5 in. (1 cm)
INSTALLATION AND USE
7. Move the filter canister to its final position.
8. Be certain the purge valve is in the vertical
(closed) position.
9. Pour about 2 gallons (8 liters) of water into the
filter canister.
IMPORTANT: Correct water volume is necessary
for system priming.
10. Place the filter lid back on the canister. Check to
make sure the filter lid seal ring is present and
installed properly on the canister lid. There is
only one orientation possible. Gently press the
lid down until the output tube is firmly seated in
the OUT connection on the filter lid.
Important: If the inlet tube attached to the
canister lid has slipped out of its seat, be sure to
fully re-insert it under the IN connection of the lid.
11. Replace and hand-tighten the eight lid fasteners.
The lid is properly closed when it is in direct
contact with the canister. DO NOT USE ANY
TOOLS, AS DOING SO MAY DAMAGE THE UNIT.
EN-10
INSTALLATION AND USE
6. Install the filter
1. Once the filter unit is in its final position, make sure that the aquarium has the appropriate
amount of water.
Important Reminders:
• The filter lid must be at least 7.8 in. (20 cm) below your aquarium’s water level but never more
than 4.9 ft. (150 cm).
• The hosing supplied with the unit is 9.8 ft. (3m) long. If longer hosing is required, intake
hosing must not exceed 9.8 ft. (3m) and the total length of intake and outlet hosing
combined must not exceed 16.4 ft. (5m).
• Hosing must follow a straight path from the filter to the aquarium rim, with some slack,
but no loops.
• For the self priming feature to work properly the water level cannot be more than 7.8 in.
(20 cm) below your aquarium rim.
• NEVER install the filter above the water level.
• For best performance, the filter should be completely beneath the aquarium.
• Position purge valve so that you will be able to attach a hose without moving the unit.
• Important: Check to be sure that the hosing follows a straight path from the aquarium rim
to the filter. Leave some slack, but no loops. If the hosing is too long, the filter will not
work efficiently.
• Assure the lid seal ring is already installed on the filter canister lid.
2. Grasp the intake valve (which is at the end of the hosing
attached to the intake tube); slide it onto the IN connection
on the filter lid, and press until it clicks into place.
3. Grasp the output valve (which is at the end of the hosing
attached to the output nozzle); slide it onto the OUT
connection on the filter lid, and press until it clicks into place.
4. Be certain both valves are locked in place and that the valve
levers are in the open (vertical) position before proceeding.
EN-11
2
3
INSTALLATION AND USE
7. Start the Filter
1. Check your installation.
Before turning the filter on, be sure that:
a. The purge valve is in the closed (vertical) position, and its
rubber cap is secured in place by the lock nut.
b. All top lid fasteners are well tightened.
c. The IN and OUT valves are fully open
(valve levers should be vertical).
d. The intake strainer is fully submersed in water.
e. There are 2 gallons (8 liters) of water in the canister.
VERY IMPORTANT: You need to know that as soon as the unit
is plugged in, it will start, and will immediately go through its
automatic priming sequence.
2. Plug the unit into an electrical outlet.
The electronic automatic priming sequence will begin.
This is what will happen:
a. The pump will run for 2 minutes to fill the filter canister
with aquarium water.
b. The pump will stop for 2 minutes to evacuate air from
the filter canister.
c. The pump will start again; it will remain on and will run
continuously until it is unplugged.
This sequence will repeat itself every time the unit is
unplugged and plugged back in.
Approximately every 24 hours: The pump will stop for
2 minutes to evacuate any air that may have become
trapped inside the unit.
EN-12
FLUVAL ADVANCED FILTRATION
There are three basic types of filtration. Mechanical
filter media removes waste particles and solid debris
through mechanical strainers. Biological filter media
breaks down and eliminate organic toxins—ammonia
and nitrite—through bacterial action. And chemical
filter media actively changes water characteristics
through deliberately managed chemical reactions.
Fluval offers a wide variety of filter media materials.
Some perform more than one job. This is the true
power of the Fluval system—the broad range of
media available for use in its baskets. These extensive
choices give you maximum flexibility in designing the
aquatic environment just right for your aquarium.
The Fluval Stack of Media Baskets
The stack of three large-capacity
media baskets in the Fluval FX5 Filter
enables you to employ all three types
of filtration, in whatever
configuration or sequence you
determine. Filtration always begins
with a mechanical stage of waste
particle removal as water is drawn
through the foam that lines the
perimeter of each basket. It continues
as water is pumped down through
the media in the three baskets. In all,
the media baskets will hold a total of
1.5 gallons (5.9 liters) of media.
❷ Middle Media Basket
The middle media basket is useful for chemically
modifying water. Peat Granules, for example will
gradually lower the water’s pH level.
The middle chamber is a good place to begin the
biological reduction process as well. Many media
types provide both mechanical filtering and
biological treatment, creating an excellent
environment for beneficial bacteria to proliferate.
Even many chemical compounds will support colonies
of bacteria. With the primary mechanical purification
of the water stream occurring in the foam inserts, it
is typical to load additional biological
media into the middle media basket.
BioMax and extra Carbon or
Ammonia Remover are commonly
used. This is also the place where
more exotic media, chosen for a
specific application, can be used.
❶
❸ Bottom Media Basket
This basket receives the purest water
stream, making it the proper place
for dedicated biological media.
Placed here, BioMax, for example,
provides optimal biological power in
a very compact ring. With a multitude
of pores perforating both the surface
and the internal matrix, it is an ideal
substrate for this position. To capture
any small particles remaining in the water before it
reaches this final stage of filtration, consider layering
a Polishing Pad, a fine mechanical filter, on top of
any biological or chemical media placed in the
bottom basket. This will prevent the clogging of the
delicate pores of the media used here, enhancing its
useful life.
❷
❸
Because you can place one, two, or
even three different kinds of media in each basket,
you will be able to design a system that provides
additional mechanical filtration, as well as biological
and chemical filtration in the widest possible variety
of combinations. This section contains detailed
information, as well as general guidelines, about
media selection and use.
❶ Top Media Basket
Pre-Filter, Carbon, and Zeo-Carb are all options for
screening small particles from the water. Pre-Filter is
inert, acting solely to create a screen. Carbon removes
dyes, medications, and solubilized wastes that a simple
screen cannot. Zeo-Carb removes ammonia; it is often
used in beginning setups to keep initial ammonia
spikes lower than would occur naturally.
To be effective, media must be cleaned or replaced
regularly. Check media monthly, and change when
necessary. However, never change all media at
the same time, or valuable bacterial colonies
will be lost.
EN-13
FLUVAL FILTER MEDIA
Foam Inserts (All Baskets)
A-228 (3-pk.)
Fluval Foam Inserts capture large particles for effective mechanical filtration, the crucial
first stage in the filtration process. Custom fit to prevent bypass, they have a pore size
that allows efficient water flow with less clogging for long-lasting filtration. These
inserts also enhance biological filtration.
For freshwater and marine environments.
Ammonia Remover (Top or Middle Media Baskets)
A-1480 (3-pk., 180g ea.)
A-1485 (700g)
A-1486 (1600g)
A-1487 (2800g)
Fluval Ammonia Remover is a natural ion-exchange media designed to remove toxic
ammonia as water passes over it. Controlling ammonia levels reduces stress on fish. Use
this product to provide a healthy environment when setting up a new aquarium or
maintaining one that contains a higher than average fish stock. Ammonia Remover
gradually becomes inactive. Replace regularly, at least once a month.
For freshwater use only.
BioMax (Middle or Bottom Media Baskets)
A-1456 (500g)
A-1457 (1100g)
Fluval BioMax ceramic rings have a complex pore system where beneficial bacteria can
thrive. With more capacity than most biological filter media, BioMax helps reduce
ammonia and nitrite. Plus, the rings allow ideal water movement throughout the
media, to ensure optimal contact time for efficient biological filtration. Replace BioMax
every 3 months. IMPORTANT: Replenish only half at one time to allow proper seeding
from older media to new.
For freshwater and marine environments.
Carbon (Top or Middle Media Baskets)
A-1440 (3-pk., 100g ea.)
A-1445 (375g)
A-1447 (900g)
A-1448 (1650g)
Fluval Carbon—a premium, research grade, low-ash carbon—improves water clarity and
color, while also removing odors. Highly porous, it provides large amounts of surface
area for adsorption of impurities. It effectively removes heavy metals, odors,
discolorations, organic contaminants, and pollutants to leave your aquarium water
crystal clear and sparkling. This product does not release phosphates. Carbon loses its
activity without outward sign. Replace monthly to ensure that active adsorption is
maintained. Carbon should always be removed when medication is being administered
in aquarium water. Also, because carbon will adsorb a large percentage of the nutrients
in plant fertilizer products, it should be used carefully when keeping live plants.
For freshwater and marine environments.
EN-14
FLUVAL FILTER MEDIA
Peat Granules (Middle Media Basket)
A-1465 (600g)
Fluval Peat Granules are the all-natural way to soften aquarium water and achieve the
pH levels required for breeding and rearing certain tropical fish. Peat contains humic
acid, tanning agents, and trace elements that are essential for various life processes.
Highly concentrated for maximum effectiveness, this product is recommended for fish
that prefer soft, acidic water.
For freshwater use only.
Polishing Pad (Top or Middle Media Baskets)
A-246 Water Polishing Pad
A-248 Fine Filter Pad
Fluval Water Polishing Pads are uniquely designed to fit Fluval canister filters. These
extra thick micro-fine polyester pads capture micro particles as the water passes
through. Use Fluval Water Polishing Pads when cloudy water occurs or after tank
maintenance for crystal clear aquarium water. Fluval Fine Filter Pads are uniquely
designed to fit Fluval canister filters. These polyester pads capture small particles and
help maintain crystal clear water. Use Fluval Fine Filter pads after using Fluval Polishing
Pads to maintain water clarity.
For freshwater and marine environments.
Pre-Filter (Top or Middle Media Baskets)
A-1470 (750g)
Fluval Pre-Filter consists of chemically inert ceramic rings designed to capture larger
solids. Trapping these particles before they can move further through the system, PreFilter prevents the clogging of active media that will filter the same water in
subsequent stages. This extends the media, and reduces the need for frequent
replacement. Pre-Filter is permanent, and requires only occasional rinsing.
For freshwater and marine environments.
Zeo-Carb (Top or Middle Media Baskets)
A-1490 (3-pk, 150g ea.)
A-1492 (1200g)
A-1493 (2100g)
Fluval Zeo-Carb is a premium blend of Fluval Carbon and Fluval Ammonia Remover.
Working together, these highly effective media eliminate liquefied impurities, odors,
and discoloration, while, at the same time, removing toxic ammonia, for a clean,
healthy aquarium. Combining two products into one gives you more space in your filter
system for other types of media. Replace once a month, more often if aquarium is
heavily populated. Remove when medication is being administered in aquarium water.
Use carefully when keeping live plants.
For freshwater use only.
EN-15
FLUVAL LAB SERIES MEDIA
Opti-Carb (Middle or Bottom Media Baskets)
A-1504 (175g)
Hi-Capacity Ion Exchange Media. Opti-Carb’s mixture of ion-exchange and synthetic
organic removal resins, and research grade carbon combine to create a powerful
adsorbent water polishing media. Rapid reduction of dissolved organic matter, removal
of proteins before they break down into toxic compounds, elimination of odors and
discolorations can all be accomplished with Opti-Carb resulting in sparkling clear
aquarium water. Use as everyday filter media or for removal of specific toxic metals and
organic compounds.
Does not affect pH, KH and general hardness. Treats up to 189 L (50 US Gal.). For larger
tanks use multiple bags.
Formulated for reef aquariums, freshwater or marine environments.
Phosphate Remover (Middle or Bottom Media Baskets)
A-1500 (150g)
Fluval Lab Series Phosphate Remover rapidly adsorbs large quantities of Phosphate,
silicate and dissolved organics without leaching adsorbed substances. Maintaining low
levels of phosphate will result in cleaner, healthier aquarium water while allowing
corals to efficiently absorb the calcium they require to grow and reproduce. Phosphate
Remover contains ferric oxide, an iron-based phosphate binder ideal for use in
aquarium filters.
150g removes up to 20 mg/L PPM of phosphate in a 50 U.S. Gal. (189 L) aquarium.
Will not affect pH or hardness.
For freshwater and marine environments.
Nitrate Remover (Middle or Bottom Media Baskets)
A-1502 (150g)
Fluval Lab Series Nitrate Remover is a high capacity laboratory developed ion exchange
resin. Developed from a pure high grade strong base anion exchange resin, Nitrate
Remover rapidly and selectively removes nitrate and eliminates toxic nitrite in a matter
of hours, resulting in a healthy environment for your fish.
• Safe for fish, plants and invertebrates
• Will not affect pH or hardness
• Does not contain phosphates
Resin can be recharged several times. Removes up to 25 mg/L (ppm) of nitrate in a 50
U.S. Gal. (189 L) aquarium.
For freshwater use only.
EN-16
MAINTENANCE PURGE VALVE DRAINING
WARNING: ALWAYS DISCONNECT ALL APPLIANCES IN THE AQUARIUM FROM ELECTRICITY SUPPLY
BEFORE PLACING HANDS IN THE WATER, BEFORE PUTTING ON OR TAKING OFF PARTS, AND
WHENEVER THE FILTER EQUIPMENT IS BEING INSTALLED, MAINTAINED OR HANDLED.
Filter media must be periodically replaced or cleaned in accordance with instructions on individual
packages. Prior to periodic media care the FX5 filter canister must be drained.
The FX5 filter offers you two methods to drain the canister:
• Option 1: Purge Valve Draining
• Option 2: Filter Pump Draining
Purge Valve Draining
To use the purge valve to drain the water from the filter canister you will need a 5/8” (1.58cm)
flexible drain hose (not supplied) that is long enough to reach from the canister to a drain or basin.
Fluval ribbed hosing item number A-20015 (sold separately) is recommended as it will secure tightly
to the purge valve using the lock nut connector.
1. Unplug the pump from the electrical power supply.
2. Turn the IN and OUT valves to the closed (horizontal) position.
3. Be certain the Purge valve is in the closed (vertical) position; turn the lock nut clockwise to
loosen it, then remove the rubber drain cap.
4. Attach one end of a flexible 5/8 in. (1.58cm) diameter hose
(not supplied) to the Purge valve, and position the other
end in an appropriate basin or discharge drain. Be sure the
hose is secured to the purge valve. If not using the Fluval
ribbed hosing it may be necessary to use a clamp to secure
the hose in place.
5. First, turn the Purge valve to the open (horizontal) position by turning it counter-clockwise.
Then disconnect the IN valve: press its release button, and lift it from the filter lid. It is a good
idea to have a cloth handy as some water will escape when removing the AquaStop Valve.
6. Water will immediately begin to drain from the canister. Since this is a gravity fed method,
water will stop draining once the water level in the canister and drain bucket equalize. Once
this happens simply close the valve and empty the bucket. Repeat the draining process until
enough water is removed to make the canister light enough to carry to your work area.
7. Once a sufficient amount of water has been removed, close the purge valve and disconnect
the drain hose. Replace the rubber drain cap and secure with the locknut, turn the locknut
counter clockwise to secure the drain cap in place. Disconnect the OUT valve and move to an
appropriate work area.
EN-17
MAINTENANCE FILTER PUMP DRAINING
Filter Pump Draining
To use the filter pump to drain the water from the filter canister
you will need to prepare a drainage hose using the third
Aquastop Valve (drainage hose and clamp not included).
1.
To prepare the drainage hose attach the third Aquastop
Valve to a 1” (2.5cm) diameter hose securing it to the
valve with a hose clamp. Follow the instructions in the
“Installation and Use” section Prepare intake connections
Step 1.
2.
Turn the IN and OUT valves to the closed
(horizontal) position.
3.
Unplug the pump from the electrical power supply.
Note: It is a good idea to have a cloth handy as some
water will escape when removing the AquaStop Valve.
4.
Disconnect both the Intake and Output Aquastop valves
from the canister.
5.
Attach the third Aqua-Stop valve with attached drainage
hose (prepared in Step 1 above) to the OUT connection
on the canister. WARNING: Be sure the Drainage Hose and
AquaStop Valve is connected to the OUT connection.
6.
Position the hose opening in an appropriate
drain basin.
7.
Plug the power cord into and electrical outlet.
8.
Open the Aquastop to the open vertical position.
Let the filter pump run until all the water is drained
from the canister.
9. Once the filter is drained unplug the unit.
10. Disconnect the drainage Aquastop Valve and move
canister to appropriate work area.
EN-18
MAINTENANCE MEDIA CARE
Cleaning or Replacing Media
1. Move the filter to an appropriate area convenient for maintenance.
2. Loosen and remove the eight lid fasteners; remove the filter lid and
set aside. Be careful not to damage the inlet stem connected to the lid.
3. Using the orange T-handles, lift the three media baskets from the filter canister;
let the T-handles fall out of their slots, and separate the baskets.
4. Remove all foam inserts from the media baskets, rinse using aquarium or de-chlorinated tap
water, or replace with new foam, as required.
5. Replace chemical media, as needed. Chemical media cannot be cleaned.
6. Rinse biological media with aquarium water, or replace, as required.
7. Empty and rinse the filter canister. NEVER use soap or detergents when cleaning the canister
or rinsing the baskets, as remaining traces of cleaning products may damage sensitive
fish tissue.
>0.5 in. (1 cm)
8. Replace foam inserts and filter media in the appropriate
areas of the baskets. Arrange foam inserts carefully, being
certain that each piece covers the entire half-circle of the
basket from bottom to top. Be sure to leave at least 0.5 in.
(1cm) of free space on the top of filter media so that
baskets will stack properly.
Reassemble Unit
1. Stack the baskets, aligning them so all shapes match.
Reinsert the T-handles into their vertical slots, and replace
the baskets in the filter canister. Foam in upper basket
should be just about even with the top edge of
the canister.
EN-19
MAINTENANCE MEDIA CARE/PURGE VALVE
2. Replace Filter Lid.
a. Inspect the Lid Gasket for wear and tear.
b. Place filter lid back on canister. There is only one orientation possible. Gently press the lid
down until the output tube, affixed to the inside of the filter canister, is firmly seated in the
output (OUT) valve lid opening.
Important: If the inlet tube attached to the canister lid has slipped our of its seat, be sure to
fully re-insert it under the IN connection of the lid.
3. Replace and hand-tighten the eight lid fasteners. The lid is properly closed when it is in direct
contact with the canister. DO NOT USE ANY TOOLS, AS DOING SO MAY DAMAGE THE UNIT.
4. Place the IN and OUT valves back on the lid connectors and press firmly until they click into
place. Be sure the IN valve is connected to the hose attached to the intake strainer, and the
OUT valve is connected to the hose attached to the output nozzle.
5. First, open the IN valve (turn to vertical position).
5
6
6. With the IN valve already open, open the OUT valve. Do
not change this sequence, or the canister will not refill
properly. If the canister is no longer primed, you will need
to remove the lid, pour about 8 liters (2 gallons) of water
into the canister, and replace the lid. (See “Prepare the
Filter” Step #7)
7. You will be able to hear water filling the canister.
Meanwhile, air will be forced through the output nozzle,
causing bubbling and agitation in the aquarium. Once the
bubbling in the aquarium stops, plug the power cord back
in. The pump will resume its normal stop/start sequence as
described in “Start the Filter.”
Purge Valve
Larger, heavier particles of aquarium debris will collect in the bottom of the canister, outside the
bottom media basket. The Purge Valve at the base of the unit allows for partial discharge of this
heavy debris. There is no need to open the filter lid or disconnect the hosing.
1. Unplug the pump from the electrical power supply.
2. Turn the IN and OUT valves to the closed (horizontal) position.
EN-20
MAINTENANCE MEDIA CARE/PURGE VALVE
3. Be certain the Purge valve is in the closed (vertical)
position; turn the lock nut clockwise to loosen it; then
remove the rubber drain cap.
4. Attach one end of a flexible 5/8 in.(1.58cm) diameter hose
(not supplied) to the Purge valve, and position the other
end in an appropriate basin or discharge drain. If not using
the Fluval ribbed hosing it may be necessary to use a clamp
to secure the hose in place.
5. a. First, turn the Purge valve to the open (horizontal)
position (rotate it counter-clockwise).
b. Then disconnect the OUT valve: press its release button,
and lift it from the filter lid.
b
6. Water will immediately begin to drain from the canister.
7. When water stops draining turn the IN valve to the open
(vertical) position for a few seconds, then close it quickly by
turning it to the closed (horizontal) position. Repeat this
sequence two or three times to create a “tide” effect that will
force much of the debris at the bottom of the filter canister out
into the basin or discharge drain.
a
8. When the purge cleaning is complete turn the IN valve to the closed (horizontal) position.
Then close the Purge Valve by turning it to the vertical position. Remove the drain hose;
replace the rubber drain cap, and secure it by turning the lock nut clockwise.
9. Replace the OUT valve back in the OUT connection on the filter lid, and press gently until it
clicks into place.
10. a. Open the IN valve.
b. Then open the OUT valve. Do not change this
sequence. The filter should refill automatically. If it
does not, fill with 8 liters of water (as in “Set Up the
Filter, Step #7).
11. Once the water level is restored, plug the unit back in.
The filter will go through its normal start up sequence.
EN-21
a
b
MAINTENANCE PUMP CARE
Pump Care: Impeller Magnet Replacement
WARNING: ALWAYS DISCONNECT ALL APPLIANCES IN THE AQUARIUM FROM ELECTRICITY SUPPLY
BEFORE PLACING HANDS IN THE WATER, BEFORE PUTTING ON OR TAKING OFF PARTS, AND
WHENEVER THE FILTER EQUIPMENT IS BEING INSTALLED, MAINTAINED OR HANDLED.
Prior to performing pump care the FX 5 filter must be completely emptied of water, media baskets,
and media.
1. Empty the filter canister by following the steps outlined in the Media Care Section. Move
unit to appropriate work space.
2. Remove all media and media baskets from the filter canister. Empty the canister completely
in a sink or basin.
3. To Remove the pump unit:
a. Place the filter unit upside down on a secure work area
so that the pump screws and screw seats are visible.
Remember that the output tube protrudes slightly from
the top rim of the canister. Be sure not to bend or
damage the tube while it is upside down.
b. Unscrew the 4 fixing screws using a Phillips
screw-driver (cross headed). Screws are located at one
end of the slits around the pump.
c. Remove the impeller assembly by grasping its flange.
b
4. Clean the impeller and the impeller well thoroughly by
rinsing with clear running water.
c
5. Reassemble all pump components with care:
a. Align the two arrows on the impeller assembly. Before
inserting the impeller, gently press the magnet against
the flange to be sure that the flange bushing is fully in
its seat.
b. Replace seal ring.
b
a
EN-22
CHANGING AQUARIUM WATER
6. Re-attach the pump unit to the canister using the 4 fixing
screws with a Phillips screw-driver (cross headed). While reassembling the pump, the 4 fixing screws should be gently
screwed until pump motor cover and canister are securely
attached. Note: Do not over tighten housing to canister.
IMPORTANT: Be sure that impeller bearing (bushing and ORing) is correctly placed at the bottom of the impeller
well. Though the bushing is made of very resistant
material, it is prone to wearing in certain conditions. For
this reason, it is recommended that you replace it
whenever the impeller unit is replaced. Follow the
instructions provided with the replacement parts package.
IMPORTANT: Be sure that the seal ring does not slip
between the impeller flange and the motor and that the
impeller bearing (bushing and O-Ring) is correctly placed
at the bottom of the impeller well.
7. Reassemble, reconnect, and restart the unit.
Changing Aquarium Water
1. Prepare drainage hose. Attach the third AquaStop valve to
a 1 in. (2.5cm) diameter hose (not supplied). Follow the
instructions in “Installation and Use/Prepare intake
connections,” Step 1.
2. Turn the in and out valves to the closed (horizontal)
position.
3. Unplug the pump from the electrical power supply.
Note: It is a good idea to have a cloth handy as some
water will escape when removing the AquaStop Valve.
EN-23
CHANGING AQUARIUM WATER
4.
Disconnect the AquaStop valve and output hosing from
OUT connection on the canister lid. Then connect the
third AquaStop valve and drainage hose (prepared in
Step 1 above) in the OUT connection.
5.
Position the open end of the drainage hose in an
appropriate drain.
6.
Turn the IN and OUT valves to the open
(vertical) position.
7.
With both valves open, plug the power cord into an
electrical outlet. Let the pump run until the desired
amount of water has been drained from the aquarium.
8.
Close the IN valve and unplug the unit.
9.
Remove the drain valve from the OUT connection on the
canister lid. CAUTION: the drain hosing may still have
some water inside.
10. Replace the OUT valve back on the OUT
lid connector.
11. Replace water.
12. Open the IN and OUT valves
(valve levers should be vertical).
13. Plug the unit.
EN-24
REPLACEMENT PARTS
M
D
B
P
H
E
J
O
Q
I
A
L
C
G
N
K
T
F
PART
QTY
NUMBER
PART
A. Lid Fasteners
1
A-20214
B. T-bar Handle
1
C. Filter Lid (O-ring)
R
S
QTY
NUMBER
K. Intake Strainer
1
A-20220
A-20240
L.
1
A-20224
1
A-20210
M. Rim Connector & clips (3)
1
A-20230
D. Rim connector Suction Cup d20 4
A-20232
N. Intake Strainer Suction Cup
2
A-15041
E. Metal Clamp (for Hosing)
2
A-20234
O. Output Nozzle
1
A-20226
F. Rubber Feet
4
A-20121
P.
Ribbed Hosing
1
A-20236
G. Motor Unit
1
A-20200
Q. Rubber Connector
2
A-20228
H. Media Basket
1
A-20238
R. Magnetic Impeller Assembly
1
A-20205
I. Top Cover Click-fit O-ring
2
A-20212
S.
1
A-20207
J. AquaStop Valve
1
A-20216
T. Purge Valve
1
A-20218
EN-25
Intake Stem
Motor Seal Ring
Media/Water Changed
Date
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
________________________________________________________
__________________________
EN-26
">