User manual | solutions for the wireless world - Navair Technologies Inc. Wireless

SOLUTIONS
FOR THE
WIRELESS WORLD
SOLUTIONS
POUR UN
MONDE SANS-FILS
Your account representative is:
2014
TABL E O F C O N T E N T S
General Purpose Test and Measurement Instruments
Rohde & Schwarz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Rohde & Schwarz HAMEG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
RF Site Measurement Products
Bird® Technologies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-14
dBm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
General Dynamics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16-17
Bird® Technologies Group – TX RX Systems Brand Products . . . . . . . . . . . . . . . . . 18-26
RF Site Management Products
Trilogy – RF Cables (PCS, Cellular, Paging Broadcast and Microwave) . . . . . . . . . 27-30
Citel – RF Surge Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-32
Telecommunications
Guisys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33-34
The R&S®RTM:
Turn on, Measure, Done
See signals where others see noise.
Don’t trade signal detail for memory
depth.
Find problems that others miss.
Finish your measurements before
others get started.
Set up a mask test in seconds.
Look back in time with the history
mode.
Reliable Results
Fast Results
Fault tolerant with undo/redo.
Virtual Screen: Two screens in one.
Quick access to all functions.
Ease-of-use
NEW
Ease of use, quick access to functions, fast and reliable results — this is precisely what
oscilloscope users want in their everyday measurement tasks. And the new R&S® RTM2000
bench oscilloscope delivers. The RTM bench oscilloscopes are for everyday use. With a
bandwidth of 350MHz or 500MHz it is ideal for your everyday applications. By combining
time domain, frequency domain, logic and protocol analysis functions in a single instrument,
they can be used for comprehensive testing of most embedded systems in development,
production and service.
See our web site for a full catalog: www.navair.com
2
NAVAIR
TECHNOLOGIES
R&S®FSH4 / R&S®FSH8 / R&S®FSH13 / R&S®FSH20 Spectrum Analyzer
The R&S®FSH4/FSH8/FSH13/FSH20 spectrum analyzer is rugged, handy and designed for use
in the field. Its low weight, its simple, well-conceived operation concept and the large number
of measurement functions make it an indispensable tool for anyone who needs an efficient
measuring instrument for outdoor work
Key Features
• Frequency range from 9 kHz to
3.6/8/13.6/20GHz
• High sensitivity (< –141 dBm (1 Hz), with
preamplifier < –161 dBm (1 Hz))
• 20 MHz demodulation bandwidth for analyzing
LTE signals
• Low measurement uncertainty (< 1 dB)
• Measurement functions for all important
measurement tasks related to the startup and
maintenance of transmitter systems
• Internal tracking generator and VSWR bridge
with built-in DC voltage supply (bias)
• Two-port network analyzer
• Rugged, splash-proof housing for rough work
in the field
• Easy handling due to low weight (3 kg with
battery) and easy-to-reach function keys
• Easy operation thanks to user configurable,
automatic test sequences (wizard)
Keep an eye on it.
The R&S®FSL Spectrum Analyzer:
to see it is to want it.
The R&S®FSL is an extremely lightweight and compact spectrum analyzer that is
ideal for a large number of applications in development, service and production.
Despite its compact size, it offers a wealth of functions more typical of the highend range, thus ensuring an excellent price/performance ratio. The R&S®FSL
is the only instrument in its class that features a tracking generator up to
18 GHz and can analyze signals with a bandwidth of 28 MHz. In addition, the
R&S®FSL18, which operates at frequencies up to 18 GHz, supports applications
in the microwave range.
• 9 Khz to 3, 6 or 18GHz, with or without tracking generator
• Best performance in its class: DANL –142 dBm, IP3 typ. +10 dBm,
phase noise typ. –103 dBc
• Comprehensive measurement routines: TOI, OBW, Time Domain Power,
CCDF, channel/adjacent channel power
• LAN interface and USB host adapter
• Unique slide-in upgrade design: all hardware options are user-installable
without opening the housing
• FSL-K93 (option) WiMAX Application Firmware for spectrum and
modulation measurements on stationary and mobile WiMAX signals.
Note: there is one vital accessory for your R&S®FSL that we don’t carry. You’ll have to visit the
hardware store for that.
See our web site for a full catalog: www.navair.com
3
NAVAIR
TECHNOLOGIES
R&S®ZVH Cable and Antenna Analyzer
R&S®NRP2 Power Meter
Key Features
• Frequency range from 100 kHz to 3.6 GHz or 8 GHz
• 100 dB (typ.) dynamic range for filter and antenna isolation measurements
• Built-in DC voltage supply (bias) for active components such as amplifiers
• Power meter option
• Saving of measurement results on SD memory card or USB memory stick
• Easy operation with user-configurable test sequences (wizard)
• Easy-to-replace Li-ion battery for up to 4.5 h of operation
• Rugged, splash-proof housing for rough work in the field
• Easy handling due to low weight (3 kg with battery) and easy-to-reach
function keys
Key Features
• Power measurements with a base unit or with cost-efficient USB
power sensors alone
• Average, peak and peak-to-average power measurements from DC to
67 GHz
• Versatile USB power sensors with superior performance
• Accurate measurements for GSM/EDGE, 3G, WLAN, WiMAX™, LTE
and beyond
• Complex signals with digital modulation are handled as easily as are
CW signals, carriers with analog modulation and pulsed RF
• Solutions for radar and EMC applications
• Ultra-fast statistical analysis
• Flexible use with signal generators, signal analyzers and network
analyzers from Rohde & Schwarz
R&S®CTH100A/R&S®CTH200A Portable Radio Test Set
Key Features
• Frequency measurement
• Power measurement
• Over-the-air measurement (R&S®CTH200A)
• Distance-to-fault measurement (R&S®CTH200A)
• Voice reporting (R&S®CTH200A)
R&S®NRP-Z Sensors
R&S®ZNC Vector Network Analyzer
Brief Description
No matter whether you work in the lab or in production – the Microwave
Power Meter R&S®NRP is always the right choice. The versatility of
the novel Power Meter Series R&S®NRP is due to the newly developed
sensors. These sensors are intelligent standalone instruments that
communicate with the base unit or a PC via a digital interface. The SMART
SENSOR TECHNOLOGY™ now implemented for the first time, sets new
standards in terms of universality and accuracy.
Key Features
• Dynamic range: up to 90 dB (sensor dependent)
• Level range: -67 dBm to +45 dBm (sensor dependent)
• Frequency range: DC to 67 GHz (sensor dependent)
• Measurement speed: 1500 measurements per second in the buffered mode
• Linearity uncertainty: 0.0007 dB
• Precise average power measurements irrespective of modulation type and
bandwidth
• Flexible measurements on up to 128 time slots per power sensor (26 time
slots with base unit)
• Direct USB connection from sensor to a PC
• S parameter correction of components between sensor and test object
• 2 years calibration cycle for base unit as well as for the sensors
Key Features
• Frequency range from 9 kHz to 3 GHz
• Dynamic range of up to 130 dB
• Short sweep times of 11 ms for 401 points
• High temperature stability of typ. 0.01 dB/°C
• Wide power sweep range from –50 dBm to +13 dBm (typ.)
• IF bandwidths from 1 Hz to 300 kHz
• Manual and automatic calibration
• Low trace noise of 0.004 dB RMS at 10 kHz IF bandwidth
• Large, high-resolution 12.1” screen
• Touchscreen user interface
See our web site for a full catalog: www.navair.com
4
NAVAIR
TECHNOLOGIES
Analog & Vector Signal Generators
ZVL Vector Network Analyzer
The cost-efficient compact class in network analysis
•
•
•
•
•
•
F requency ranges from 9 kHz to 3 GHz/6 GHz/13.6 GHz
Wide dynamic range: >115 dB, typ. 123 dB
Bidirectional test set: display of all four S-parameters
75 Ω version from 9 kHz to 3 GHz for TV/CATV
Complete spectrum analyzer as an option
Compact size and low weight (<7 kg)
• Digital communications standards
• Accurate power measurement (USB connector for R&S® NRP-Z power
sensor series)
• Compact size and low weight (<7 kg)
• 12 V DC operation and internal battery
• Connection for external monitor
The New Standard of Excellence
in Analog Signal Generation
R&S®SMA100A
The R&S®SMA100A combines superior signal
quality with a very high setting speed, making it
the ideal generator for any task in development,
production, service or maintenance.
Setting Standards in Mid-range
Analog Signal Generation
R&S®SMB100A
The R&S®SMB100A sets new standards in its
class due to its outstanding characteristics. The
instrument combines excellent signal quality with
very high output power, which makes it ideal for
any task.
Key Features
• Frequency range from 9 kHz to 3 GHz or 6 GHz
with or without an electronic attenuator
• CW signal and all common types of analog
modulations (AM, FM, φM, PM)
• Very low phase noise
• High power output as standard
• Optional removable mass memory card
Key Features
• Wide frequency range from 9 kHz to
1.1/2.2/3.2/6 GHz or from 100 kHz to
12.75/20/40 GHz
• Excellent signal characteristics with low
SSB phase noise of typ. –128 dBc
(at 1 GHz, 20 kHz offset)
• High output power of typ. up to +27 dBm
• All important analog modulations with AM,
FM/φM and pulse modulation supported
• Compact size with only two height units,
3/4 19” width and low weight
Best Price/Performance Ratio and Key Features
• Frequency range from 9 kHz to 1.1 GHz
Smallest Size in its Class
R&S®SMC100A
The R&S®SMC100A is the newest analog
signal generator that Rohde & Schwarz has
to offer. It has a very small size and is priced
very attractively to reduce overall total cost
of ownership.
See our web site for a full catalog: www.navair.com
5
or 3.3 GHz
• Outstanding signal quality
• All analog modulation types and high output
power as standard
• Electronic attenuator
• Low phase noise and fast switching time
NAVAIR
TECHNOLOGIES
Analog & Vector Signal Generators
Generating Signals for Today
and Tomorrow
R&S®SMBV100A
The R&S®SMBV100A is a state-of-the art vector
signal generator that has been designed with a
future-proof hardware concept.
Compact, cost-effective
measuring receiver
R&S®ESL EMI Test Receiver
The R&S®ESL EMI test receiver combines
two instruments in one, measuring EMC
disturbances in accordance with the latest
standards and also serving as a full-featured
spectrum analyzer for diverse lab applications.
The R&S®ESL is the ideal instrument for small
budgets.
Key Features
• Frequency range from 9 kHz to 3.2 GHz
or 6 GHz
• Excellent characteristics and high output power
as standard
• Wide RF signal bandwidth of up to 120 MHz with
internal signal generation
• Maximum supported external RF bandwidth is
500 MHz
• Supports all of the important digital standards
available now such as WiMAX, 3GPP and LTE,
as well as any future digital standards still in
development
Key Features
• Frequency range from 9 kHz to 3 GHz or 9 kHz
to 6 GHz covering almost all commercial EMC
standards
• First-ever combination of an EMI test receiver
and spectrum analyzer in the entry-level class
• All major functions of an advanced EMI test
receiver, including fully automated test sequences
• Weighting detectors: max./min. peak, average,
RMS, quasi-peak as well as average with meter
time constant and rms-average in accordance
with the latest version of CISPR 16-1-1
• Compact, lightweight instrument, can be batterypowered for mobile applications
R&S®HE300
Active Directional Antenna
20 MHz (optional 9 kHz) to 7.5 GHz
Key Features
The practical and very wideband R&S®HE300
active directional antenna locates transmitters
and interference sources when combined with
portable receivers (e.g. the R&S®PR100).
• Very wideband performance in a practical size
Three exchangeable antenna modules that are
supplied with the antenna cover the 20 MHz to
7.5 GHz frequency range. An additional module
(R&S®HE300HF for 9 kHz to 20 MHz) is available
as an option.
• Unambiguous radiation pattern
• Direction is found by orienting antenna toward
maximum field strength
• Low weight, due to optimized selection of
materials, ensures fatigue-proof handling
• Horizontal and vertical polarization
• Wide dynamic range
• Passive antenna if amplifier is switched off
The modules can be plugged into the handle
with the correct orientation for vertical or
horizontal polarization and then mechanically
locked in place.
A built-in, low-noise wideband amplifier can be
activated to enhance system sensitivity (active
mode).
In passive mode, the amplifier is bypassed so
that the R&S®HE300 can also be used in the
vicinity of strong signal sources.
See our web site for a full catalog: www.navair.com
6
NAVAIR
TECHNOLOGIES
Oscilloscopes
HMO3000 Series
Mixed Signal Oscilloscopes
500 MHz | 400 MHz | 300 MHz
200 MHz | 150 MHz | 100 MHz | 70 MHz
4 GSa /s real time, low noise flash A /D converter
8 MPts memory,
oom up to 200,000:1
MSO functionality included as standard
(HO3508/HO3516 logic probe with 8/16 channels required)
Automatically or manually adjustable memory depth
300 MHz | 400 MHz >>> 500 MHz
HMO Compact Series
2 GSa/s real time, low noise flash A/D converter
2 MPts memory,
oom up to 50,000:1
MSO functionality included as standard
(HO3508 logic probe with 8 channels required)
C
omponent tester for capacitors, inductors
and semiconductors
E
Elektronik
Product of the Year
The HMO3000 series is future-proof
due to bandwidth upgrade option
HOO352 / 354 and HOO452 / 454
2012
HMO1024
No. 1 in Category
Test + Measurement
All HMO Oscilloscopes Feature:
erticalsensitivityupto1mV/div.
V
Triggermodes:slope(A/B),pulsewidth,video,logic,
serialbuses(optional),hold-off*
S
erialbustriggerandhardwareaccelerateddecodeincl.listview.
Options:I2C+SPI+UART/RS-232(HOO10/HOO11),CAN+LIN(HOO12)
28auto-measurementparametersplusstatistics,formulaeditor,
ratiocursor
6-digithardwarecounter
FFTwithupto64kPts(dBm,dBV,Vrms)
ass/failtestbasedonmasks
P
Automaticsearchforuser-definedevents
Display:12div.x-Axis,20div.y-Axis
(VirtualScreen)
*HMO3000modelsonly
*
*HMO300x,HMO202x,HMO152xonly
HMO3000 Series
HMOseriesataglance:
Bandwidth
Model: 4 channel
2 channel
HMO Compact Series
500MHz
400MHz
300MHz
200MHz
150MHz
100MHz
70MHz
HMO3054
HMO3052
HMO3044
HMO3042
HMO3034
HMO3032
HMO2024
HMO2022
HMO1524
HMO1522
HMO1024
HMO1022
HMO724
HMO722
Sampling rate (per analog channel)
2GSa/s
1GSa/s
Maximum sampling rate
4GSa/s
2GSa/s
Memory depth per channel
4MPts.
1MPts.
Maximum memory
8MPts.
2MPts.
16
8
Max number of logic channels
Input impedance
1MΩ/50Ω
1MΩ/50Ω
1MΩ
V/div. @ 1 MΩ
1mV/div.to5V/div.
V/div. @ 50 Ω
1mV/div.to1V/div.
1mV/div.to1V/div.
n/a
±0,2Vto±50V
±0,2Vto±100V
–
DC-offset
Component tester
1mV/div.to10V/div.
–
See our web site for a full catalog: www.navair.com
•
7
NAVAIR
TECHNOLOGIES
Spectrum Analysis
HMS-X Spectrum Analyzer 1.6 GHz | 3 GHz
1 Basic Unit + 3 Options =
Your HMS Spectrum Analyzer
qFrequency range: 100 kHz to 1.6 GHz/3 GHz*1
qSpectral purity greater than -100 dBc/Hz (at 100 kHz)
qSWEEP from 20 ms to 1000 s
qDetectors: auto-, min-/max.-peak, sample, RMS, average, quasi-peak*2
qMiscellaneous marker/Δmarker and peak functions
qTracking generator*3
Frequency range: 5 MHz to 1.6 GHz/3 GHz*1
Output level: -20 dBm to 0 dBm
qDirectly export data to USB flash drive, RS-232/USB dual interface
for remote control
qFanless design and fast boot time
One HMS-X basic unit and three options allow you to configure an
instrument that best fits your needs
HMS-TG This option activates the tracking generator in the
instrument.
HMS-3G The frequency range is increased from 1.6 GHz to 3 GHz
with this option.
HMS-EMC This option activates all the functions that are required
for EMC precompliance measurements. The preamplifier
option has been integrated into the new HMS EMC
option.
You can easily upgrade all three available options at any later point in
time with option upgrade vouchers.
*1 with HMS-3G (HV212) option
*2 with HMS-EMC (HV213) option
*3 with HMS-TG (HV211) option
HMS-X series model overview
HMS-X with EMC option
HMS-X basic unit
Amplitude measurement range
-114 dBm to +20 dBm
-104 dBm to +20 dBm
DANL
typ. -135 dBm
typ. -104 dBm
Resolution bandwidth
100 Hz to 1 MHz, 200 kHz (-3 dB),
200 Hz, 9 kHz, 120 kHz, 1 MHz (-6 dB)
10 kHz to 1 MHz, 200 kHz (-3 dB)
Video bandwidth
10 Hz to 1 MHz
1 kHz to 1 MHz
EMC precompliance set 1 GHz HMS-SET1
The EMC precompliance set HMS-SET1 includes
all necessary instruments to analyse typical EMC
problems. This set contains a spectrum analyzer
HMS-X incl. HMS-EMC option, a probe set HZ530,
the HM6050-2 LISN for line conducted measurements
and the HMExplorer software for EMC precompliance
measurements.
+
HMS-X incl. HMS-EMC option
+
HZ530 1GHz
HM6050-2
EMC precompliance set 3 GHz HMS-SET2
The EMC precompliance set HMS-SET2 includes
all necessary instruments to analyse typical EMC
problems. This set contains a spectrum analyzer
HMS-X incl. HMS-EMC and HMS-3G option, a probe
set HZ540, the HM6050-2 LISN for line conducted
measurements and the HMExplorer software for EMC
precompliance measurements.
+
HMS-X incl. HMS-EMC
and HMS-3G option
See our web site for a full catalog: www.navair.com
8
+
HZ540 3 GHz
HM6050-2
NAVAIR
TECHNOLOGIES
ModularSystem
SystemSeries
Series8000
8000
Modular
Mainframe
HM8001-2
Key facts
❙ Basic unit for modules of the modular system series 8000
❙ Power supply for 2 modules
❙ DC voltages electronically regulated, floating and short-circuit proof
❙ Power transformer with thermal fuse
❙ Up to 5 mainframes can be stacked
4 BNC connectors option HO801
4 BNC connectors on the rear panel of the HM8001-2 allow signal
transmission to or from HM8021-4
and HM8030-6 modules
4 ¾-Digit Programmable
Multimeter
HM8012
Key facts
❙
❙
❙
❙
LCR Meter
HM8018
Key facts
❙ Measurement functions: L, C, R, Θ, Q/D, |Z| ❙ Basic accuracy 0.2 %
❙ 5 measurement frequencies:
100 Hz, 120 Hz, 1 kHz, 10 kHz, 25 kHz
Universal Counter 1.6 GHz
HM8021-4
Key facts
❙ Measurement range 0 Hz to 1.6 GHz
❙ 10 MHz time base with 1 ppm stability (TCXO)
❙ Input A: input impedance 1 MΩ, sensitivity 20 mVrms
Input C: input impedance 50 Ω, sensitivity 30 mVrms
8-digit resolution for 10 s measuring time
Function Generator 10 MHz
HM8030-6
Key facts
❙ Frequency range 50 mHz to10 MHz,
output voltage up to 10 Vpp (into 50 Ω)
❙ Waveforms: sine wave, triangle, square wave, pulse, DC
❙ Distortion factor <0.5 % up to 1 MHz, rise and fall time typ. 15 ns
Tripple Power Supply
HM8040-3
Key facts
❙ 2 x 0 to 20 V/0.5 A | 1 x 5 V/1 A
❙ 3-digit switchable displays (display resolution 0.1 V/1 mA)
❙ Pushbutton to activate / deactivate all outputs
Key facts
Blank Module
HM800
See our web site for a full catalog: www.navair.com
4 ¾-digit display with 50,000 counts
Basic accuracy 0.05 %
Max. resolution: 10 µV, 0.01 dBm, 10 nA, 10 mΩ, 0.1 °C
Offset function/relative value measurement
❙ Module for customized instrument construction
❙ Guide rails for mounting circuit boards at 4 different levels
❙ Plastic front panel for easy mechanical processing
8
9
NAVAIR
NAVAIR
TECHNOLOGIES
TECHNOLOGIES
Power Supplies
Programmable 3[4] Channel
High-Performance Power Supply
HMP4030 [HMP4040]
q 3 x 0…32 V/0…10 A 384 W max.
[4 x 0…32 V/0…10 A 384 W max.]
q 384 W Output Power realized by intelligent Power Management
q Low Residual Ripple: <150 μVrms due to linear Post Regulators
q High Setting- and Read-Back Resolution of 1 mV up to 0.2 mA
q Keypad for direct Parameter Entry
q Galvanically isolated, earth-free and short circuit protected Output Channels
q Advanced Parallel- and Serial Operation via V/I Tracking
q EasyArb Function for free definable V/I Characteristics
q FuseLink: Individual Channel Combination of Electronic Fuses
q Free adjustable Overvoltage Protection (OVP) for all Outputs
q All Parameters clearly displayed via LCD/Illuminated Buttons
q Rear Connectors for all Channels including Sense
q USB/RS-232 Interface, optional Ethernet/USB or IEEE-488 (GPIB)
Programmable 2[3] Channel
High-Performance Power Supply
HMP2020 [HMP2030]
q 1 x 0…32 V/0…10 A [3 x 0…32 V/0…5 A 1 x 0…32 V/0…5 A 188 W max.]
188 W max.
q 188 W Output Power realized by intelligent Power Management
q Low Residual Ripple: <150 μVrms due to linear Post Regulators
q High Setting- and Read-Back Resolution of 1 mV up to 0.1 mA
q Galvanically isolated, earth-free and short circuit protected Output Channels
q Advanced Parallel- and Serial Operation via V/I Tracking
q EasyArb Function for free definable V/I Characteristics
q FuseLink: Individual Channel Combination of Electronic Fuses
q Free adjustable Overvoltage Protection (OVP) for all Outputs
q All Parameters clearly displayed via LCD/Illuminated Buttons
q Rear Connectors for all Channels including Sense
q USB/RS-232 Interface, optional Ethernet/USB or IEEE-488 (GPIB)
Triple Power Supply
HM7042-5
q 2 x 0…32 V/0…2 A 1 x 0…5.5 V/0…5 A
q High-Performance and inexpensive Laboratory Power Supply
q Floating, overload and short-circuit proof Outputs
q Separate Voltage and Current Displays for each Output 4 Digits at Channel 1+3; 3 Digits at Channel 2
q Display Resolution: 10 mV/1 mA at Channel 1+3; 10 mV/10 mA at Channel 2
q Protection of sensitive Loads by Current Limit or Electronic Fuse
q Pushbutton for activating/deactivating all Outputs
q Low Residual Ripple, high Output Power, very good Regulation
q Parallel (up to 9 A) and Series (up to 69.5 V) Operation
q Temperature-controlled Fan
See our web site for a full catalog: www.navair.com
10
NAVAIR
TECHNOLOGIES
Programmable Measuring
25MHz [50MHz] Arbitrary
Function Generator
HMF2525 [HMF2550]
5 ¾-Digit Digital Multimeter
HMC8012 | HMC8012-G
NEW
q Frequency Range 10 μHz…25 MHz [50 MHz]
q Measurement range: DC to 100 kHz)
q Output Voltage 5 mVpp…10 Vpp (into 50 Ω) DC Offset ±5 mV…5 V
q Resolution: 1 μV, 100 nA, 1 mΩ, 1 pF, 1 Hz, 0.1 °C/F
q Arbitrary Waveform Generator: 250 MSa/s, 14 Bit, 256 kPts
q Basic accuracy: 0.015 % (DC)
q Sine, Square, Pulse, Triangle, Ramp, Arbitrary Waveforms incl. Standard Curves
(white Noise, Cardiac etc.)
q True RMS measurement, AC and AC+DC
q Total harmonic Distortion 0.04 % (f <100 kHz)
q Measurement rate: up to 200 values per second
q Burst, Sweep, Gating, external Trigger
q Measurement functions: VDC, IDC, RMS, VAC, IAC, frequency, DC power, resistance
(2- and 4-wire), temperature, capacitance, diode and continuity test
qSimultaneous display of three measurement functions, e.g. DC + AC + statistics
q Rise Time <8 ns, in Pulse Mode 8…500 ns Variable-Edge-Time
q Pulse Mode: Frequency Range 100 μHz…12.5 MHz [25 MHz], Pulse Width
15 ns…999 s, Resolution 5 ns
q Mathematic functions: limit testing, Min/Max, average, offset, DC power, dB, dBm
q Modulation Modes AM, FM, PM, PWM, FSK (int. and ext.)
q 10 MHz Timebase: ±1 ppm TCXO, rear I/O BNC Connector
q Interfaces: USB-TMC/-VCP, Ethernet, LXI, IEEE-488 (GPIB)* SCPI commands widely
compatible with Agilent 34410A
q Front USB Connector: Save and Recall of Waveforms and Settings
*HMC8012-G only
q Data logging to internal memory or USB flash drive in .csv-format
q 8.9 cm (3.5”) TFT: crisp Representation of the Waveform and all Parameters
q USB/RS-232 Dual-Interface, optional Ethernet/USB or IEEE-488 (GPIB)
200kHz LCR-Bridge
HM8118
3GHz Programmable Counter
HM8123
q Basic Accuracy 0.05 %
q Measurement Range 0 Hz…3 GHz
q Measurement Functions L, C, R, |Z|, X, |Y|, G, B, D, Q,Θ, Δ, M, N
q 2 Measurement Inputs DC…200 MHz, 1 Measurement Input 100 MHz…3 GHz
q Test Frequencies 20 Hz…200 kHz
q Input Impedance A/B: 1 MΩ/50 Ω (switchable), Sensitivity 25 mVrms
q Up to 12 Measurements per Second
q Input Impedance C: 50 Ω, Sensitivity 30 mVrms
q Parallel and Series Mode
q 400 MHz Time Base with 0.5 ppm Stability
q Binning Interface HO118 (optional) for automatic Sorting of Components
q 10-Digit Resolution at 10 s Gate Time
q Internal programmable Voltage and Current Bias
q 9 Measurement Functions, external Gate and Arming
q Transformer Parameter Measurement
q Input for external Time Base (10 MHz)
q External Capacitor Bias up to 40 V
q Kelvin Cable and 4-Wire SMD Test Adapter included in Delivery
q Standard: TCXO (Temperature Stability: ±0.5 x 10-6) Optional: OCXO (Temperature
Stability: ±1 x 10-8)
q Galvanically isolated USB/RS-232 Interface, optional IEEE-488 (GPIB)
q Intuitive One-Pushbutton Operation. Each Function directly Addressable
q Galvanically isolated USB/RS-232 Interface, optional IEEE-488 (GPIB)
See our web site for a full catalog: www.navair.com
11
NAVAIR
TECHNOLOGIES
SignalHawktm
SIGNALHAWKTM VNA | Spectrum Analyzer with Power Meter Option
MODEL SH-362S: Spectrum Analyzer & 2-Port VNA
MODEL SH-361S: Spectrum Analyzer & 1-Port VNA
MODEL SH-362: 2-Port VNA (1.6MHz-3.6GHz)
MODEL SH-36S: Spectrum Analyzer (100kHz to 3.6GHz)
Bird Technologies SignalHawkTM Analyzes radio frequency spectrum.
Measures intended and interfering signals. Allows setup of parameters
such as frequency, amplitude, and markers. Graphically displays signal
amplitude vs. frequency and saves traces.
KEY FEATURES
• Fast, Accurate, and Sensitive: -42 dB Directivity and-135 dBm Noise Floor
• Large High-Resolution Display: Full Color, Indoor/Outdoor Viewable
• Easy-to-Use: Intuitive Menus, One-Button Setup, and On-Board Help
• Long Battery Life: 5.5 Hours per Charge, Field Replaceable Battery
• Rugged: Drop Tested per Military and European Standards
• USB Connectivity: USB Drive Stores 90,000 Traces
• Spectrogram
• GPS
• Power measurement interface
• Internal Bias – Tee
Model SH-36S SignalHawkTM
ALSO AVAILABLE
Bird®Rack-Mount SignalHawkTM Spectrum Analyzer
Model SH-36S-RM: 100kHz to 3.6 GHz
Remotely analyzes the radio frequency spectrum. From your office: measures
intended and interfering signals, allows setup of parameters such as frequency and
amplitude markers. Also, remotely displays signal amplitude vs. frequency and saves
traces to your PC.
Bird®PC SignalHawk Spectrum Analyzer
Model SH-36S-PC: 100kHz to 3.6 GHz
Analyzes the radio frequency spectrum. Measures intended and interfering signals, allows
setup of parameters such as frequency and amplitude markers. Also, displays signal
amplitude vs. frequency and saves traces on your PC.
WORLDWIDE APPLICATIONS
Cellular, PCS, DCS, 2G, 3G, 4G, CDMA, cdmaOne, CDMA 2000, 1x, 1x EV-DO, GSM, GPRS, EDGE, UMTS, HSDPA,W-CDMA, TDMA,
AMPS 802.11, Bluetooth, Broadcast, Emergency, Fire, GPS, HDTV, IBOC, In-Building, Lab, Microwave, NPSPAC, Paging, Police, Private,
Project 25, Public Safety, Tactical Military, Telematics, Tetra, Trunking, Utilities,WiMAX,WLAN and WLL.
See our web site for a full catalog: www.navair.com
12
NAVAIR
TECHNOLOGIES
Bird® Model 5000-XT
Hand-Held Digital Power Meter
The hand-held digital power meter has been completely redesigned with the new Bird® 5000-XT. Ideally suited
for field techs and engineers who need to make power measurements anywhere they go, the 5000-XT’s new
user interface has an intuitive, menu-driven design, making it the easiest to use on the market. It’s operable
even with one hand and compatible with all our field and legacy sensors.
Bird AT Series
AT-500 & AT-800
R
®
Bird AT Series
AT-500 & AT800
Antenna Testers
Antena Testers
The Bird AT-Series Antenna Testers provide a cost-effective, fast, graphical
way of determining the quality of mobile and base station antennas.
• Rugged, easy-to-use, hand-held design with extended battery life makes it ideal
foruseinthefield.
•TeststhesysteminVSWR,ReturnLoss,MatchEfficiency,orReflection
Coefficient(Rho)
• Single frequency readings and frequency sweeps allow for everything from
pinpointests to system optimization and tuning.
• Can save up to 12 traces for comparison and tracking over time
• RS232 Interface allows communication with a PC for saving traces using
the optional software.
Frequency Characteristics:
Frequency Range
AT-500 2 to 520 MHz
AT-800 806 to 960 MHz
Frequency Resolution 20 kHz
Frequency Accuracy
50 kHz
®
Number
of
points
100
BIRD ANTENNA & CABLE MONITOR
General Requirements:
Dimensions8”x4-5/8”x1-3/4”(204x118x42mm)
Minimize
Weight 2.0 lbs (0.9 kg)
Downtime
Temperature, Operating 0 to 50 C (32 to 122 F) Keep Your Critical
Antenna Sites
Temperature, Storage -40 to +71 C (-40 to +160 UpF)& Running
Humidity 95% 5% max (noncondensing)
Compliance Unit complies with MIL-T-28800 Class 5
except for temperature and humidity. Unit is
CE-compliant and RoHS compliant.
Bird Antenna
®
Cable Monitor
Accurately detects antenna system degradation and failures
Measurements:
Rho 0.000 to 1.000
• Compatible
with analog 0ortodigital
Match Efficiency
100%cellular and two-way radio systems
• Worldwide
applications
Return
Loss include
-32 to 0Tetra,
dB Cellular, PCS and many others
1.00
to 100.00
• Monitors VSWRVSWR
and power
levels
and provides alarm outputs
Accessories:
• Sensitive toAccuracy
antenna faults
internal transmitter VSWR monitors may not detect
Measurement
Rhothat 0.04
Antenna & Interseries Adapter, N (M)
4240-402
Match
Efficiency
Calculated
from
Cable Monitor
• Local
or remote
operation
via PC software
PC Software
Tool
4240-403 Interseries Adapter,
N (F)
Loss applications
Rho accuracy
7005A970
• Ideal forReturn
multi-carrier
(OptionalBNC
Accessory)
4240-404 Interseries Adapter,
(M)
• Now availableVSWR
with Ethernet Connectivity!
Test Port:
4240-405 Interseries Adapter, BNC (F)
Connector N(F) supplied. N, TNC, UHF, BNC, male
4240-406 Interseries Adapter, TNC (M)
13
See our web site for a full catalog:
www.navair.com
or female
available
4240-407 Interseries Adapter, TNC (F)
VSWR 1.25 max
4240-408 Interseries Adapter, UHF (M)
NAVAIR
TECHNOLOGIES
Bird®Wideband Power Sensor
5012B, 5016B, 5017B, 5018B, 5019B
Bird’s® Wideband Power Sensor (WPS) never requires field calibration, only
requires calibration once per year and is traceable to National Institute of Standards
and Technology (NIST). The WPS measures True Average Power, Peak Power, and
Duty Cycle directly with exceptional accuracy and uses these precise measurements
to calculate a wide range of other important factors, such as VSWR, Return Loss,
Reflection Coefficient, Crest Factor, Average Burst Power, and CCDF.
PROBLEMS
Downtime is necessary
Have analog, digital, and multi-carrier signals
to measure
Tight budgets
Varying field tech skill levels
Need greater confidence in measurement
SOLUTIONS
Monitor and perform maintenance for
monitoring while DUT is in-service
Measure forward and reflected power to
troubleshoot system failures
Modulation independent measurements
USB connectivity, no meter required
Sensor plugs and plays with 5000-XT meter
No field calibration required
NIST traceable calibration
APPLICATIONS
WPS measures: Analog Cellular, Digital
Cellular, 3G, 4G, Tetra, APCO/P25, Trunking,
CDMA, TDMA, WCDMA, GSM, Transportation,
Tactical Military, Radar, Avionics, Marine, LMR,
Analog Broadcast, Digital Broadcast, GSM,
GPRS, EDGE, UMTS, HSDPA, Bluetooth, Fire,
GPS, NPSPAC, Paging, Project 25, Public
Safety, Telematics, Utilities, WIMAX and WLAN.
Measurements performed: Peak power, true
average power and Duty Cycle.
Calculations Performed: VSWR, Return Loss,
Reflection Coefficient, Crest Factor, Average
Burst Power and CCDF.
Bird®Site Analyzer XT Series
SA-3600XT (25-3600 MHz)
SA-6000XT (25-6000 MHz)
• One unit covers the entire 25-6000 MHz range!
• Easy to operate and field ready for first-time, occasional and experienced users.
• Other applications include 3G, Broadcast, Government, Tactical Military,
Microwave, Paging, Public Safety, Trunking, WLAN and WLL, and TETRA.
• Color display is clearly visible in direct sunlight.
• With a single download you can view data as Distance to Fault or Measurement
Match-no need to store two traces.
• FDR (Frequency Domain Reflectometry) measurement method results in a
highly reliable assessment of the health of critical components in your system;
ultimately providing a “heads-up” before a failure occurs.
• Fault location or DTF mode indicates VSWR or Return Loss levels at each point
along the cable and antenna system length.
• Cable Loss function measures insertion loss of the cable system over a given
frequency range.
• USB communication ports for connection to PC, field sensors and storage devices.
See our web site for a full catalog: www.navair.com
14
APPLICATIONS
Suitable for use in Worldwide Cellular and
PCS/DCSsystems; supporting measurement
of CDMA, GSM, TDMA and AMPS modulation
schemes.
Other applications include 3G,
Broadcast,Government, Tactical Military,
Microwave, Paging,Public Safety, Trunking,
WLAN and WLL, and TETRA.
NAVAIR
TECHNOLOGIES
Carrier to Noise Generator CNG-70/140
RF Converter Series UDC-172-302-2
APPLICATIONS:
• Bit error rate/SINAD testing
• SATCOM modems
• Channel impairment tests
• Development, qualification, and verification testing
• Manufacturing test
APPLICATIONS:
• A laboratory workhorse
• Programmable LO for frequency converters
• Frequency hopping source
• RF device characterization
• Tracking generator source
FEATURES:
• C/N, C/No, Eb/No, and C/I modes
• 1 or 2 independent RF channels
• Continuous input power monitoring
• Un-interrupted signal path during calibration cycle
• IEEE-488.2 and RS-232 interface
• Easy to read VFD display
FEATURES:
• Low noise (-103 dBc/Hz 1 kHz offset @ 1GHz)
• Fast switching (<2msec typ.)
• Small and lightweight (10” x 10” x 3”)
• Non-volatile memory for storage/recall of instrument settings
• IEEE-488.2, LAN, and RS-232 interfaces standard
Satellite Link Emulator SLE9000 Series
Precision White Gaussian Noise Generator
OPTIONS:
• Fast switching speed (200 usec)
• File driven hopping/swept frequency mode
APPLICATIONS:
• Bit error rate (BER) and SINAD testing
• Component and subsystem linearity characterization
• Wireless link emulation
APPLICATIONS:
• Earth terminal testing
• Satellite payload testing
• Satellite system integration test beds
• Mobile transceiver testing
• UAV Testing
FEATURES:
• Calibrated noise density over entire operating frequency
• Noise power/bandwidth and noise density control
• Solid state noise attenuator with 0.0156 dB resolution
• IEEE-488.2 interface
Optional
• Multipath Fading, 6 paths
• Digitally generated AWGN
Multiple Orbit Models
Emulates earth-to-satellite-to-earth, earth-to-satellite links; Low Earth
Orbit; Medium Earth Orbit, Geostationary and Geosynchronous, satellite
to satellite links and satellite to UAV testing.
Test Data Generation
dBm’s standard SATGEN software data generation package or Analytical
Graphics STKTM package may be used to generate the necessary test
data. SLEControl, a windows based applet will automatically format
download the test files for execution in dynamic mode.
See our web site for a full catalog: www.navair.com
15
NAVAIR
TECHNOLOGIES
R8000B Communications System Analyzer
The R8000B delivers a previously unimaginable result: a truly portable radio test
set with more functions than yesterday’s bench top analyzers. And it now offers
industry-leading spectral purity, surpassing that of comparably priced and even
much more expensive radio test sets.
The R8000’s 14 pound weight gives technicians power and flexibility never before
attainable – or currently attainable with any other instrument. This, combined
with the unit’s feature-packed spectrum analyzer and bright 8.4” color LCD,
makes it ideal for taking to sites for infrastructure maintenance and interference
measurement.
Firmware upgrades are available free via web download for the life of the unit,
and new capabilities are being constantly added — so your R8000B actually
becomes more powerful over time! Software and protocol options can also be
added directly from the front panel in less than 30 seconds; so it is clear that the
R8000B is the most flexible, robust future-proofed radio test set the industry has
ever seen. The R8000B will change the way you perform radio service forever.”
A Compact and Lightweight Solution
You no longer need to lug multiple pieces of heavy equipment to perform service at remote locations. The R8000 has everything you need in
one compact, 14 lb. package! Among the instruments included in the R8000 are:
• Spectrum Analyzer
• Signal Generator
• Sensitive Measurement Receiver
• Tracking Generator (optional)
• SINAD Meter
• Distortion Meter
• Modulation Scope
• Oscilloscope
• Frequency Error Meter
• Cable Fault Locator (optional)
• FM Deviation Meter
• AM Modulation Meter
• Receive Signal Strength Meter
• Broadband and Narrowband Power Meters
• Audio Counter
• Audio Generator
• AC / DC Voltmeters
• DMR (MOTOTRBO™) test mode (optional)
• NXDN test mode (optional)
• TETRA Subscriber Test (optional)
• P25 test mode (optional)
AutoTune for the R8000 Automated Test and Alignment
The R8000’s AutoTune option performs all manufacturer-recommended tests and alignment
procedures in a fraction of the time needed to perform them manually.
With AutoTune, your R8000 automatically reads the radio model and serial numbers and makes the
measurements and alignments needed to bring the radio within factory specifications. Ideal for large radio fleets
with Preventative Maintenance (PM) programs, the AutoTune option records a complete record of your test
session and allows you to build a complete test history of every radio in the fleet.
AutoTune for the R8000 reduces the time it takes to test and align a radio from an hour or more to
10-12 minutes, and is presently available for Motorola XTL Series mobiles, XTS2500/5000 portables and
APX6000/7000 Series mobiles and portables.
Benefits:
• Reduces test time by over 80%
• Maintains consistency and accurate test results from radio to radio
• Can be used by non-technical personnel
• Adjustable Pass/Fail indicators flag radio defects
• Results can be stored on the R8000 and exported to a USB drive for analysis with PC spreadsheet software
• Comprehensive test report shows date of test, model, serial number, operator ID and complete test record
See our web site for a full catalog: www.navair.com
16
NAVAIR
TECHNOLOGIES
Geographic Signal Coverage at your Fingertips
Setting the Standard for Automated Measurement, Analysis and Report of
Wireless System Signal Coverage
STI Field Test 7 is automated signal measurement and analysis software that can be interfaced with the R8000B. STI Field Test 7 includes a
GPS receiver, street map data for the entire United States of America and Canada with major highways worldwide, an RF instrument interface/
driver, manual and one year warranty, allowing you to integrate your laptop PC and digital radio test set or spectrum analyzer to create a
coverage verification system that meets your requirements.
The versatile STI Field Test 7 interface software allows for connection to the proprietary or application-specific receiver of your choice. The types
The first
step toward
of signal measurements taken are limited only by the capabilities of the RF measurement
instrument
used. This unique feature ensures a long
and useful life for your STI system.
improving system coverage
to understand
currentfield measurement and analysis
From digital BER, to analog SINAD, and signal strength to modulation fidelity, STI isField
Test 7 is the automated
package to measure mobile communication system coverage and performance. system performance.
See our web site for a full catalog: www.navair.com
17
NAVAIR
TECHNOLOGIES
RF INFRASTRUCTURE PRODUCTS
Broadband
RX Antenns
700/800 MHz
T-Pass TX Combiner
Tower Top
Amplifier
Repeater #1
Broadband
TX Antenns
Repeater #2
Repeater #3
Repeater #4
Repeater #5
792-824 MHz
Preselector
746-901 MHz Receive Multicoupler
Multiband Shorthaul
Control Station Combiner
43-05-01A Series
BTG, TX RX System multi-channel multi-band combiners provide
frequency-agile operation across multiple bands. Interoperability can
be combined into a single network for efficiency.
PROBLEMS
SOLUTIONS
Many bands on site with frequencies from VHF
to 900 MHz
- Multiband combiner allows operation in
multiple bands
Standardization across all sites
- Advance coupler technology with no need for
tuning — control stations can be connected
without regard to frequency
Space constraints
Cost reduction
- Low Profile for space efficient installation
- Multiple bands can utilize the same
combiner for cost reduction
APPLICATIONS
Control Station Combiners operating in
multiplebands may be used to reduce
the number of antennas required on a
communications site while also ensuring
that predictable radio-to-radio isolation is
maintained at all times — irrespective of
individual radio’s Tx or Rx operating mode or
antenna isolation characteristics.
Is ideally used with multiband coupler
Bird®SB I Series Signal Boosters
62-89B, 62-90A Series
NPSPAC
Bird Technologies Group, TX RX Systems brand, SB I Series family
of signal boosters provides an exceptional balance of performance
and value for extended coverage of radio communications networks.
PROBLEMS
SOLUTIONS
RF coverage is required for different building
sizes and configurations
- Bird® SB I is available in two output
power models:
System monitoring is required
- High power model (+35 dBm)
Need to eliminate potential interference and
unwanted coverage
- Low power model (+25.5 dBm)
Reliable in-building communications is a must
- Alarm and sampler port are available
- Gain is adjustable from 0 to 30 dB in
2 dB increments
- Bird invented the signal booster and has
been a leader in providing reliable inbuilding wireless solutions since 1980
APPLICATIONS
Cost effective in-building coverage solutions
for applications in critical communications
systems
Public Safety, Private Wireless networks
Excellent selectivity for operation in a shared
frequency band
See our web site for a full catalog: www.navair.com
19
NAVAIR
TECHNOLOGIES
Bird®SB I Series Signal Boosters
62-83E-Series
Dual Band 700/800 MHz
Bird Technologies Group, TX RX Systems brand, SB I Series family of
signal boosters provides an exceptional balance of performance and
value for extended coverage of radio communications networks.
PROBLEMS
SOLUTIONS
RF coverage is required for different building
sizes and configurations
- Bird SB I is available in two output
power models:
System monitoring is required
Need to eliminate potential interference and
unwanted coverage
Reliable in-building communications is a must
Need to provide coverage for both 700 MHz
and 800 MHz
- High power model (+34 dBm)
- Low power model (+25.5 dBm)
- Alarm and sampler port are available
- Gain is adjustable from 0 to 30 dB in
2 dB increments
- Bird invented the signal booster and has
been a leader in providing reliable inbuilding wireless solutions since 1980
- SB I dual band provides coverage of both
frequencies in one unit
APPLICATIONS
Cost effective in-building coverage solutions
for applications in critical communications
systems
Public Safety, Private Wireless networks
Excellent selectivity for operation in a shared
frequency band
Bird®SB I Series Signal Boosters
62-91-Series
Cellular A, B, & A/B Bands
Bird Technologies Group, TX RX Systems brand, SB I Series family
of signal boosters provides an exceptional balance of performance
and value for extended coverage of radio communications networks.
PROBLEMS
SOLUTIONS
RF coverage is required for different building
sizes and configurations
- Bird SB I is available in two output
power models:
System monitoring is required
- High power model (+34 dBm)
Need to eliminate potential interference and
unwanted coverage
- Low power model (+25.5 dBm)
Reliable in-building communications is a must
- Alarm and sampler port are available
- Gain is adjustable from 0 to 30 dB in
2 dB increments
- Bird invented the signal booster and has
been a leader in providing reliable inbuilding wireless solutions since 1980
APPLICATIONS
Cost effective in-building coverage solutions
for applications in critical communications
systems
Coverage of full Cellular A/B bands or each
band individually
Excellent selectivity for operation in a shared
frequency band
See our web site for a full catalog: www.navair.com
20
NAVAIR
TECHNOLOGIES
Bird® Signal Booster II Series
Supports UHF and 700/800/900MHz.
Mission Critical Reliability for In-building Coverage . . .
The New Signal Booster II provides Public Safety grade reliability and coveragein
disadvantaged RF locations for First Responders, Public Safety/Governmental
agencies and Private System Users. Reliable RF coverage is gained in basements,
parking garages, correctional facilities, courthouses, hospitals, malls and schools.
Other challenging environments covered by the Signal Booster II product include
subways and rapid transit systems, airports, stadiums/arenas, high-rise buildings
and large private enterprise facilities and campuses.
Whether you are on the front line and depend on a reliable communication
system or you are the systems integrator responsible for implementing
adependable system, this new compact design facilitates installation and system
optimization for rock solid operation via a simple man-machine interface.
Imbedded features for ease of initial setup include decoupled test points for
signal level detection, menu driven gain setting, front panel LED monitors for
amplifier and power status, and an at-a-glance LED bargraph to indicate relative
level of Output Level Control (OLC). Additionally, this product offers a unique
on-board OLC Data Log feature thatarchives a User Signal Profile to facilitate
optimumsystem configurationand performance.
Output Level Control (OLC) Circuit Monitors and
Controls RF Output Power
Microprocessor Controlled Fault Monitoring and Alarming
Ensures Reliable Operation and Flexible Configuration
•Maintains maximum required output power while preventing damage
and excessive emissions per FCC requirements
•Control system continuously monitors parameters including voltage,
current, temperature and OLC activity
•Easy-to-read LED bar graph
•LEDs on each module quickly annunciate source of fault
•Unique OLC DataLog feature facilitates system maintenance and
optimization
•Simple, back-lit liquid crystal display (LCD) and switch control
Decoupled RF Test Points For Simplified Service
•Fault triggers annunciation on panel, alarm contact closure and internal
recording of failed subsystem
•Allow fast system measurements in both uplink and downlink directions
Programmable Gain Setting
•Monitor signals for performance optimization
•Ease of initial configuration via front panel
•Integrated design facilitates non-intrusive measurements
•When used in conjunction with OLC DataLog, simplifies post installation
adjustments
Secure, Non-Vented NEMA Enclosure Suitable for Extreme
Indoor and Outdoor Environments
Three Major Gain Ranges Available
Optional Features Available
Low:+ 45 dB, Medium:+ 60 dB, High:+ 80 dB
•Comm Card II for remote communications and control
•Fiber optic link interface
•Redundant PA configuration
•-48 VDC input
All Signal Booster II products comes with a 5 year OEM warranty
See our web site for a full catalog: www.navair.com
21
NAVAIR
TECHNOLOGIES
Bird® Digital Signal Booster
Model 613-8-Series
Bird Technologies, TX RX Systems Digital Signal Booster operates
in the 700/800 MHz range with 1-60 programmable digital filters for
both uplink and downlink. Filter center frequency and characteristics
are fully programmable to meet the demands of various systems
and signals such as APCO 25 phase II. Filter bandwidth is user
programmable from 6.25 kHz to 15 MHz. All state-of-the-art product
components are protected by a NEMA 4 style enclosure to meet the
demands of the NFPA requirements. Intuitive web browser interface
allows booster to be easily configured for changing RF environments.
PROBLEMS
Noise and Interference that cause communication
problems in a crowded spectrum.
Changes in RF environment.
System coverage is difficult to assess.
SOLUTIONS
Digital booster can amplify several individual
channels or narrow bands of frequencies
(amplifying the desired spectrum and
preventing interference to other users).
An intuitive web browser user interface offers
not only local but also remote access from
any compatible PC on the network maximizing
flexibility to easily implement system changes
such as output power, center frequency, filter
shape, and group delay.
Built-in pilot signal capability. The 1 kHz
FM modulated carrier allows simple SINAD
qualification testing.
APPLICATIONS
Any communications system installation where
you need to reduce the number of antennas on
a tower.
Any communications system designed to
minimize tower size and maximize site space
Secured applications that require equipment
under lock and key
Bird®7020 Series Power Sensor
Bird’s® new 7020 Power Sensor is an economical plug andplay solution to
your power measurement needs. The 7020 determines and reports Forward
and Reflected True Average Power and VSWR over a wide frequency range
of 350 MHz to 4.0 GHz. It also never requires field calibration, only requires
factory calibration once per year, and is traceable to National Institute of
Standards and Technology (NIST).
PROBLEMS
SOLUTIONS
APPLICATIONS
Have analog, digital, and multi-carrier signals to
measure
Modulation independent measurements
Tight budget
Complimentary Virtual Power Meter
(VPM2) application
WPS measures: Analog Cellular, Digital Cellular,
3G, 4G,Tetra, APCO/P25, Trunking, CDMA,
TDMA, WCDMA, GSM,Transportation, Tactical
Military, Radar, Avionics, Marine, LMR, Analog
Broadcast, Digital Broadcast, GSM, GPRS,EDGE,
UMTS, HSDPA, Bluetooth, Fire, GPS, NPSPAC,
Pag-ing, Project 25, Public Safety, Telematics,
Utilities, WIMAX and WLAN.
Downtime is unacceptable
Varying field tech skilllevels
Need confidence inmeasurement
Inline device, no directional coupler required
Monitor and perform maintenancefor monitoring
while DUT is in-service
Measure forward and reflectedpower to
troubleshoot system failures
Sensor plugs and plays with multiple
display devices.
Measurements performed: Forward and Reflected
Calculations Performed: VSWR and True Average
Power
No field calibration required
NIST traceable calibration
See our web site for a full catalog: www.navair.com
22
NAVAIR
TECHNOLOGIES
Bird® Compact Ceramic TX Combiner
Model 73-67-50 Series
BTG, TX RX System brand UHF Ceramic TX Combiner combines up to 6 transmitters onto a
single antenna. With a footprint that’s more than 50% smaller than comparably performing
10” cavities. This optimizes valuable space for your radio equipment, which in an era of
escalating lease costs, makes it the perfect solution for expansion. And because of our
modular design, you can purchase in single-channel increments. Plus, it delivers the kind
of high performance and minimum interference you’ve come to expect from Bird®.
PROBLEMS
May need to minimize the number of antennas at
a communication site.
Need to maintain or minimize additional
costs associated with space in a radio shack/
transmitter shelter.
Need to minimize interference with competing
communication systems.
And may lack the time or expertise to integrate
the solution into the overall radio system.
SOLUTIONS
Can combine up to six transmitters onto a single
antenna which efficiently utilizes valuable rack
and shelter space.
Our units provide valuable real estate in small
shelters where traditional T-Pass combiners are
too large.
System-level signal analysis (including interference mitigation) for each customer application.
Offer complete solutions from system design
through individualized configurations, installation support, and maintenance programs.
APPLICATIONS
Any communications system installation where
you need to reduce the number of antennas on
a tower.
Any communications system designed to
minimize tower size and maximize site space
Secured applications that require equipment
under lock and key
Mini AutoQuad™
Tower Top Amplifier System
434 Mission Critical Series
Bird, TX RX Systems brand, Auto Quad Tower-Top Amplifier (TTA) system is a high performance,
quadrature-coupled low noise amplifier (LNA). The TTA increases receive sensitivity, reduces
transmit signal interference and can make all the difference in Mission Critical Communications.
The TTA operates independently, monitoring LNA current and automatically switching to a
redundant LNA if needed. Status reporting is accomplished via AISG compliant telemetry between
the controlling processor in the Tower Box and the base control unit. The base control unit has
an on board AISG modem device which does not require the use of an external data cable. This
telemetry does not interfere with RF Signals in any way and communicates the LNA currents,
temperature and operational status to the base control unit LCD display. Test modes and manual
switching between LNA’s is also accomplished by way of the telemetry system.
The TTA consists of two components: the tower top amplifier mounted close to the antenna and the control unit.
The control unit is available in two styles, either with or without a receiver multicoupler. In order to reduce the size of the TTA and simultaneously
provide 120 dB of isolation of a TX carrier, filtering has been split between the TTA and the base unit.
Industry leading TTA amplifier linearity guarantees superior immunity to intermodulation interference.
FEATURES
All tower top ports protected by internal surge suppressors.
Two independent quadrature coupled LNA’s in the tower top assembly
provides redundancy. Microprocessors continuously monitor amplifiers
and will switch tower top LNA’s when needed to ensure the maximum
uptime.
At a glance status reporting and form-C contact switching intiated when
alarm detected.
Wind loading is reduced due to the small enclosure size.
Available with a 16 Port Receive Multicoupler or a Control Monitoring Unit.
See our web site for a full catalog: www.navair.com
23
APPLICATIONS
The TTA is designed to increase the performance of a Base Transceiver
Station (BTS) while ensuring reliable communications for critical Public
Safety applications. This increase in sensitivity can make up for the
imbalance between mobile and handheld users in critical systems.
NAVAIR
TECHNOLOGIES
Compact Receiver
Multicouplers
Compact
Receiver
Multicouplers
Receiver Multicouplers
TX RX Systems Inc. has designed a new series of Compact Receiver Multicouplers that offer superior specifications in
a one rack unit package. By utilizing broadband preamps and power supplies, three basic products cover most
applications in the 118 - 901 MHz range.
Receiver Multicoupler Features:
Sleek, 19” 1 RU rack mount design
Low noise, high performance amplifiers
AC & DC power input
Auto-Ranging AC Power, 85-264 VAC
DC Power Input, 12-24 VDC
Receiver Multicoupler Specifications
MODEL
NUMBER
NUMBER
OF
CHANNELS
BANDWIDTH
SYSTEM
GAIN
(TYPICAL)*
PREAMP
NOISE
FIGURE
PREAMP
3RD ORDER
OUTPUT
INTERCEPT
POINT
POWER
REQUIREMENT
42-33-01-04N
4
118-174 MHz
22 dB
2.0 dB
41 dBm
85-264 VAC, 47-63 Hz
12-26 V
N(f)/N(f)
1.75"H x 19"W x 14"D
42-33-01-08N
8
118-174 MHz
15 dB
2.0 dB
41 dBm
85-264 VAC, 47-63 Hz
12-26 V
N(f)/N(f)
1.75"H x 19"W x 14"D
42-33-01-12N
12
118-174 MHz
15 dB
2.0 dB
41 dBm
85-264 VAC, 47-63 Hz
12-26 V
N(f)/N(f)
1.75"H x 19"W x 14"D
42-33-01-08
8
118-174 MHz
17 dB
2.0 dB
41 dBm
85-264 VAC, 47-63 Hz
12-26 V
N(f)/BNC(f)
1.75"H x 19"W x 14"D
42-33-01
16
118-174 MHz
10 dB
2.0 dB
41 dBm
85-264 VAC, 47-63 Hz
12-26 V
N(f)/BNC(f)
1.75"H x 19"W x 14"D
42-57-01-04N
4
380-520 MHz
22 dB
1.7 dB
41 dBm
85-264 VAC, 47-63 Hz
12-26 V
N(f)/N(f)
1.75"H x 19"W x 14"D
42-57-01-08N
8
380-520 MHz
15 dB
1.7 dB
41 dBm
85-264 VAC, 47-63 Hz
12-26 V
N(f)/N(f)
1.75"H x 19"W x 14"D
42-57-01-12N
12
380-520 MHz
15 dB
1.7 dB
41 dBm
85-264 VAC, 47-63 Hz
12-26 V
N(f)/N(f)
1.75"H x 19"W x 14"D
42-57-01-08
8
380-520 MHz
17 dB
1.7 dB
41 dBm
85-264 VAC, 47-63 Hz
12-26 V
N(f)/BNC(f)
1.75"H x 19"W x 14"D
42-57-01
16
380-520 MHz
10 dB
1.7 dB
41 dBm
85-264 VAC, 47-63 Hz
12-26 V
N(f)/BNC(f)
1.75"H x 19"W x 14"D
42-83A-01-08
8
746-901 MHz
19 dB
1.5 dB
41 dBm
85-264 VAC, 47-63 Hz
12-26 V
N(f)/BNC(f)
1.75"H x 19"W x 14"D
42-83A-01
16
746-901 MHz
12 dB
1.5 dB
41 dBm
85-264 VAC, 47-63 Hz
12-26 V
N(f)/BNC(f)
1.75"H x 19"W x 14"D
DC
CONNECTORS
BACKUP
(IN/OUT)
DIMENSIONS
Combline Preselector
792-824 MHz
COMBLINE PRESELECTOR 792-824 MHz
*Attenuator pads are provided for system optimization
TX RX Systems Inc. Manufacturers a comprehensive line of Preselectors and filters for a broad
ranges of applications. Contact your Navair representative for specific product information.
See our web site for a full catalog: www.navair.com
24
Model Number
89-83C-01-32
Power Rating
Rx Only
Pass Bandwidth
792-824 MHz
Passband Insertion Loss
1.5 dB nominal
Selectivity @ 776 & 851 MHz
>110 dB
VSWR
1.5:1 max.
Connectors (Input/Output
N-female
Mounting
19” Rack Mount Panel
Dimensions
3.5”H x 19”W x 7”D
Weight
8 lbs est.
NAVAIR
TECHNOLOGIES
Duplexers
Duplexers
Model Number
30-37-01A
Model Number
28-37-02A
144-174 MHz • 6.625” Diameter
144-174 MHz • 2” Square
Model Number
Power Rating
Minimum Separation
Channel Isolation
Insertion Loss
Connectors ( Tx & Rx / Ant.)
Mounting
Dimensions
Model Number
Power Rating
Minimum Separation
Channel Isolation
Insertion Loss
Connectors
Mounting
Dimensions
30-37-01A
100 Watts
3 MHz
100 dB
1.5 dB
BNC(F) / N(F)
19" Rack Mount Bar
5.25"H x 19"W x 7.25"D
Model Number
28-70-02A
Model Number
28-70-15H
450-470 MHz • 4” Diameter
Model Number
Power Rating
Minimum Separation
Channel Isolation
Insertion Loss
Connectors
Mounting
Dimensions
28-37-02A
400 Watts
500 KHz
85 dB
1.5 dB
N-female
19” Rack Mount Bars
33"H x 19"W x 15"D
450-470 MHz • 1.25”x 2” Rectangular
Model Number
Power Rating
Minimum Separation
Channel Isolation
Insertion Loss
Connectors
28-70-02A
350 Watts
5 MHz
100 dB
0.6 dB
N-female
19" Rack Mount Bars
5.25"H x 19"W x 12"D
28-70-15H
100 Watts
5 MHz
80 dB
1.2 dB
BNC(F) / UHF(F)
(Tx & Rx / Ant.)
Mounting
Mobile Mount Plate
Dimensions
2.7"H x 5.2"W x 7.4"D
Model Number
28-89-01A
Model Number
26-89-03A
806-869 MHz • Single Frequency Pair
806-866 MHz • Trunking Combline
Model Number
Power Rating
Minimum Separation
Channel Isolation
Insertion Loss
Connectors
Mounting
Dimensions
Model Number
Power Rating
Minimum Separation
Channel Isolation
Insertion Loss
Connectors
Mounting
Dimensions
28-89-01A
125 Watts
45 MHz
90 dB
0.8 dB
N-female
19" Rack Mount Bars
5.25"H x 19"W x 10"D
See our web site for a full catalog: www.navair.com
25
TX RX Systems Inc.
716-549-4700 www.txrx.com
26-89-03A
600 Watts
45 MHz
45 dB Tx / 77 dB Rx
0.5 dB Tx / 1.0 dB Rx
N-female
19" Rack Mount Panel
5.25"H x 19"W x 9"D
NAVAIR
TECHNOLOGIES
T-PASS® EXPANDABLE
T-PASS EXPANDABLE
TRANSMITTER
COMBINERS
TRANSMITTER
COMBINERS
®
746-869 MHz
T-Pass® combiner systems can be expanded one
channel at a time with factory-tuned, easy-to-install
expansion channel assemblies. Expansion is usually
accomplished without modifications to the existing
system, and it amounts to nothing more than placing a
new channel assembly, or several, on top of the existing system. New channel frequencies can be above,
below, or between existing channel frequencies.
TX RX Systems T-Pass® transmitter combiners utilize
innovative, three-port bandpass cavities of patented
design (U.S. Patents No. 4,249,147 and 4,493,422)
and dual ferrite isolators to provide all the benefits of
ordinary cavity/ferrite combiners:
• Significantly lower channel insertion loss than
hybrid/ferrite combiners;
• High isolation between transmitters;
• High antenna-to-transmitter isolation;
• High intermodulation suppression
• Excellent transmitter noise suppression.
Unlike ordinary cavity/ferrite combiners, T-Pass®
transmitter combiners are inherently expandable,
broadband and easily adaptable to the most difficult
duplex system design requirements.
Superior Expandability and Bandwidth
Ordinary cavity/ferrite combiners rely upon quarterwave cable transformers, resonant stubs and star
junctions for combining groups of two, four or five
channels. Mechanical problems quickly develop in the
process of trying to locate several groups of cavities in
close proximity to each other. Additionally, because of
the frequency-sensitive, narrowband nature of the
cable transformers, operating bandwidth is usually
restricted to about 6% of system center frequency.
NEW
T-Pass® channel interconnect cables are individually
optimized to their own channel frequency. No compromises are necessary to accommodate other channel
frequencies. Each channel can therefore be anywhere
in a very broad frequency range. T-Pass® coupling
loops and interconnect cables are elegantly designed
to operate together as a broadband 50-ohm transmission line. Individual channel frequencies are therefore
not restricted to a narrow operating bandwidth, as in
the case of ordinary cavity or cavity/ferrite combiners.
T-Pass® transmitter combiners are inherently capable
of operating over bandwidths that span the entire 746869 MHz frequency range.
Expansion Channel
746-869 MHz T-Pass® transmitter combiner channel
assemblies consist of the following items:
• A 6.625” 3-quarterwave T-Pass® cavity filter;
• A dual ferrite isolator, with RF loads and coaxial
cable for connection to cavity.
• An RF sampler to measure RF power reflected
into the isolator output load
• Isolator and channel mounting hardware
Expansion assemblies (channel 2 and higher) are supplied with a thruline of the correct length for the new
and existing channel frequencies. Starter channels
(channel 1, bottom) are supplied with a short circuit on
the T-Pass loop.
All T-Pass Expandable Transmitter Combiners comes with a 5 year OEM warranty.
See our web site for a full catalog: www.navair.com
26
NAVAIR
TECHNOLOGIES
Trilogy’s AirCell® cables embody innovative, waterproof air-dielectric design, consistent manufacturing, and quality assurance
techniques in accordance with ISO-9001 procedures. The result is a coaxial cable with superior electrical and mechanical
­performance that completely eliminates water migration.
Trilogy’s AirCell® Transline cable is designed for base station applications and is field proven in cellular, PCS, ESMR, paging,
broadcast, and microwave applications. AirCell® Transline cables are available with impedances of 50 Ohms in 1/2", 5/8", 7/8", ­
1-1/4", and 1-5/8" sizes and with impedances of 75 Ohms in 1/2", 5/8", and 7/8" sizes.
To accompany our cables,Trilogy offers a complete line of connectors, accessories, and cable assemblies for all your wireless
application needs.
AirCell® Transline cable is designed for the following applications:
PCS, Cellular, and Paging
Trilogy’s cables and connectors are ideally suited to the high performance requirements of cellular and PCS applications.
Transline cable’s excellent insertion loss,VSWR, and intermodulation characteristics enhance both digital and analog systems.
Water migration problems are non-existent because of the unique AirCell® design. Trilogy’s high performance connectors are
easily attached to form a solid watertight assembly that will provide trouble free communications for the life of your system.
Broadcast
Having the easiest installation in the industry makes AirCell® Transline cable the best choice for radio and television broadcast
antenna feeders and for AM, FM, shortwave,VHF, and UHF frequencies.
Microwave
Trilogy’s AirCell® Transline cable is perfect for all private and PTF microwave applications. Transline cable’s superior VSWR
­performance has been specifically tested for microwave applications. The cable’s strong, rugged design as well as flexibility
makes it easy to install in any climate, and its weatherproof properties result in a life expectancy of over 15 years.
Enhanced Specialized Mobile Radio (ESMR)
The low attenuation and high shielding effectiveness of AirCell® Transline make it an ideal replacement for braided cable.
The low insertion loss of Trilogy’s AirCell® Transline cables typically provides double the coverage area for the same transmit
power, or it can provide coverage to the same area and use lower transmit power.
Level of Fire Retardancy
The standard Transline cable construction uses a weather-resistant, black polyethylene jacket suitable for indoor, outdoor, or
underground installations. For additional requirements regarding flame retardancy, AirCell® Transline cables are available with a
non-halogenated, flame retardant jacket, which meets the most stringent fire retardancy requirements of UL, NEC, IEC, MSHA.
See our web site for a full catalog: www.navair.com
27
NAVAIR
TECHNOLOGIES
NextG Plenum
For 4G Systems
100% Made in the USA
• ElectricalPerformanceSurpassesCopper
• LighterWeightandEnvironmentallyFriendly
AirCell®® Plenum Cable
• FastestandEasiestConnectorization
• PreferredChoiceforOperatorsandIntegrators
28
See our web site
for a full catalog:
www.navair.com
800-TRILOGY
(874-5649)
www.trilogycoax.com
·
·
[email protected]
NAVAIR
TECHNOLOGIES
50 Ohm Plenum, 1/2”
50 Ohm Plenum, 1/2″ (6 GHz)
Description
*
Product Number
Attenuation and Average Power
Standard Cable*
1/2″, Corrugated, Jacketed UL-910,
CATVP
Frequency
MHz
AP6012J50
Physical Dimensions
Attenuation
dB/100 ft dB/100m
Avg. Pwr.
kW
100
0.70
2.30
3.98
450
1.50
4.92
1.85
Center Dia., in (mm)
0.188 (4.78)
500
1.59
5.22
1.75
Dia. Over Dielectric, in (mm)
0.470 (11.94)
600
1.75
5.74
1.58
Dia. Over Outer Conductor, in (mm)
0.540 (13.72)
700
1.87
6.13
1.47
Dia. Over Jacket, in (mm)
0.615 (15.62)
800
1.96
6.43
1.37
Center Conductor
Copper Clad Aluminum
900
2.14
7.02
1.29
Outer Conductor
Corrugated Aluminum
960
2.23
7.31
1.24
Jacket Color
Off-white
1000
2.30
7.54
1.21
1500
2.85
9.35
0.98
Electrical Characteristics
Maximum Frequency, GHz
10
1700
3.05
10.00
0.98
Peak Power Rating, KW
35
1800
3.14
10.30
0.93
1950
3.24
10.63
0.85
DC Res., Ohms/1000 ft (1000m)
Center
0.46 (1.51)
2000
3.33
10.92
0.84
Outer
0.51 (1.67)
2100
3.42
11.22
0.82
DC Breakdown, kV
4
2200
3.50
11.48
0.80
Capacitance, pF/ft (m)
22 (72.12)
2300
3.59
11.78
0.78
Inductance, mH/ft (m)
0.057 (0.187)
2400
3.67
12.04
0.77
Jacket Spark, kV RMS
8
2500
3.75
12.30
0.75
Impedance, Ohms
50
2700
3.90
12.82
0.72
Velocity of Propagation
94%
3000
4.14
13.58
0.68
3300
4.33
14.20
0.61
Mechanical Characteristics
Min. Bend. Radius, in (mm) – Single
2 (50.8)
3400
4.45
14.60
0.60
Min. Bend. Radius, in (mm) – Multiple
5 (127)
4000
4.91
16.10
0.55
Cable Weight, lb/ft (kg/m)
0.129 (0.192)
4900
5.61
18.40
0.50
Bending Moment, ft.lb (N.m)
1 (1.4)
5000
5.69
18.66
0.49
Tensile Strength, lb (kg)
250 (114)
5200
5.92
19.42
0.48
Flat Plate Crush, lb/in (kg/mm)
78 (1.39)
5300
6.03
19.78
0.47
*Direct Substitute/Equivalent
to Andrew LDF4-50 15
Number
of Bends, minimum
5600
6.37
20.89
0.46
Number of Bends, typical
5825
6.83
22.40
0.45
25
Temperature, oF (oC)
Recommended Install
+5 to 194 (-15 to 90)
Recommended Storage
+5 to 194 (-15 to 90)
Operating
+5 to 194 (-15 to 90)
See our web site for a full catalog: www.navair.com
29
Standard conditions:
For attenuation, VSWR 1.0, ambient temperature 20°C (68°F)
For average power, VSWR 1.0, ambient temperature 40°C (104°F),
inner conductor temperature 100°C (212°F), no solar loading
NAVAIR
TECHNOLOGIES
PLENUM CABLES
Cable Selection Guide
50 and 75 Ohm, Plenum and Plenum Radiating
75 Ohm Plenum, 1/2″50-Ohm
Cable Size, 1/2”
Description
Jacketing
Plenum Cables
Plenum
75 Ohm
Plenum
Product
Product
Code Code
Product Code
1/2"
Corrugated
AP012J75 APC012J50
Jacketed
UL-910, Cable,
CATVP Jacketed UL-910,
AP012J50
CATVP
Unjacketed UL-910
AP012U50
Physical Dimensions
Characteristics
Center
Conductor
Copper Clad Aluminum
Outer
Outer Conductor
Conductor
Corrugated Aluminum
Aluminum
Copper
Dia. Over
Over Outer
in (mm)
0.540(13.72)
Dia.
OuterConductor,
Conductor,
in (mm) 0.540 (13.72)
0.540 (13.72)
Dia.
Over
Jacket,
in
(mm)
0.615
(15.62)
0.615
(15.62)
Dia. Over Jacket, in (mm)
0.615 (15.62)
Cable Weight,
lb/ft (kg/m)
Electrical
Characteristics
Jacketed
0.129 (0.192)
0.19 (0.28)
Impedance, Ohms
75
Unjacketed
0.082 (0.122)
Maximum Frequency, GHz
12
Min. Bending Radius, in (mm)
5 (127)
5 (127)
Velocity of Propagation
95%
Impedance, Ohms
50
50
Peak Power Rating, kW
35
Velocity of Propagation
93%
96%
DC
Res., Ohms/1000 ft (1000 m)
Maximum Frequency, GHz
10
10
Center
1.09 (3.58)
Peak Power Rating, Kw
35
40
Outer
0.51 (1.67)
DC
Breakdown,dB/100
kV
4
Attenuation,
ft (dB/100 m)
50 MHzSpark, kV RMS
0.51 (1.74)
Jacket
8
100 MHz
Capacitance,
pF/ft (m)
150 MHz
Inductance,
mH/ft (m)
450 MHz
Mechanical
Characteristics
900 MHz
Minimum Bending Radius, in (mm)
1000 MHz
Number of Bends, minimum (typical)
1700 MHz
Cable Weight, lb/ft (kg/m)
2000 MHz
Unjacketed
2300 MHz
Jacketed
2400
MHz
Tensile
Strength, lb (kg)
3000 MHz
78 (1.39)
50Recommended
MHz
Install
100
MHz
Recommended
Storage
150
MHz
Operating +5 to 194
450 MHz
900 MHz
1000 MHz
1700 MHz
2000 MHz
2300 MHz
2400 MHz
3000 MHz
Frequency
MHz
AQ012J50
Plenum
5
Attenuation
Avg. Pwr.
dB/100
ft
dB/100m
kW
AQC012J50
AP012J75
0.15
0.49
9.33
AP012U75
10
0.21
0.70
6.60
20
0.30
0.98
4.66
30
Aluminum
0.540
50(13.72)
0.615
88(15.62)
0.37 Copper 1.21
0.540 (13.72)1.57
0.48
0.615 (15.62)2.18
0.66
100
0.71
2.32
150
0.87
2.85
0.122
108(0.181)
5 (127)
174
50
200
93%
300
10
400
35
450
0.64
512(2.11)
0.97
600(3.19)
1.27
700(4.15)
2.60
800(8.52)
4.09 (13.4)
824
4.27 (14.0)
894
5.66 (18.6)
960
6.43 (21.1)
1000
7.10 (23.32)
1250
7.34
(24.1)
1500
8.82 (29.0)
1700
Avg Pwr Rating,
Temperature
°FkW
(°C)
Plenum Radiating
and Average
Power
Product Attenuation
Code
Product
Code
Product Code
500
0.44 (1.44)
0.72 (2.47)
0.63
(2.05)
14.84 (48.68)
0.88 (3.03)
0.080 (0.264)0.77 (2.53)
1.57 (5.32)
1.36 (4.46)
2.33 (7.64)
1.95 (6.41)
5.0 (127)
2.40 (8.10)
2.07 (6.78)
15 (20)
3.20 (10.0)
2.74 (9.00)
3.50 (11.7)
2.99 (9.82)
0.058
(0.086)
3.76 (12.6)
3.23 (10.59)
0.104 (0.155)
3.92 (12.9)
3.22 (10.57)
145 (66)
4.38 (14.5)
3.73 (12.25)
Flat Plate Crush Strength lb/in ( kg/mm)
Plenum Radiating
0.740.17 (0.25) 2.42
5 (127)
0.93
50
1.00
96%
1.20 10
1.40 40
3.07
3.29
3.94
4.59
1.48
4.87
1.57
5.15
1.590.65 (2.12) 5.21
1.730.92 (3.01) 5.68
1.871.12 (3.69) 6.13
2.021.96 (6.42) 6.62
2.78 (9.13)
2.05
6.73
2.94 (9.63)
2.14
7.01
3.85 (12.63)
2.21
7.25
4.18 (13.72)
2.26
7.41
4.49 (14.74)
2.57
4.59 (15.07)8.43
2.81
5.15 (16.90)9.22
3.01
9.88
3.78
Aluminum
0.540 (13.72)
2.93
0.615 (15.62)
2.10
1.97
0.104 (0.155)
1.90
0.058 (0.086)
1.61
5 (127)
1.50
75
1.40
95%
1.17
12
351.00
0.94
0.89
0.48
0.71
0.87
1.48
2.14
2.26
3.01
3.29
3.52
3.60
4.03
(1.57)
0.88
(2.32)
0.81
(2.85)
0.75
(4.87)
0.69
(7.03)
0.68
(7.41)
0.66
(9.88)
0.63
(10.8)
0.62
(11.6)
0.54
(11.8)
0.50
(13.2)
0.46
Coupling Loss, dB,
at 6ft (2m) 10.7 Avg Pwr Rating,
1950
3.25
0.43 kW
5.66
+5 to 194 (-15 to6.34
90)
3.98
+5 to 194 (-15 to4.46
90)
3.20
3.63
(-15 to 90)
1.85
2.06
1.29
1.43
1.21
1.35
0.98
1.02
0.84
0.93
0.78
0.86
0.77
0.82
0.68
0.75
See our web site for a full catalog: www.navair.com
30
49
2000
55
2.93
10.8
0.43
49
1.97
2300
3.52 55
11.6
0.40
49
56
1.61
2400
3.60
11.8
0.39
61
63
0.94
3000
4.03
13.2
0.35
63
65
0.65
Standard64
conditions:
65
0.62
For attenuation,VSWR
1.0, ambient
(68°F)
65
66 temperature 20°C
0.46
68 power, VSWR 1.0,67
For average
ambient temperature0.43
40°C
(104°F), inner
100°C (212°F),0.40
no
69 conductor temperature
68
solar loading
70
68
0.39
70
69
0.35
3.29
NAVAIR
TECHNOLOGIES
RF Surge Protection
Table below allows comparison between the 3 technologies of RF coaxial surge protectors, in order to select the right
solution regarding the application and the requirements.
Technology
Gas tube
DC Block
Quarter wave
CITEL series
P8AX
CXP-DCB
PRC
Principle
Sparkover
Sparkover + Filtering
Adapted short-circuit/selective band filter
Residual voltage
from 70V to 600 V in relation with the
dV/dt , then arc regime (short - circuit
of the line in the full bandwidth). RF
signal disturbed during the protection
o peration.
< 100 V
< 20 V
Short-circuit of the line in the full
bandwidth : RF signal disturbed during
the protection operation.
RF signal not disturbed during the
protection operation.
Bandwidth
DC to 3GHz (dependent of the coaxial
connector and of the impedance)
125-1000 MHz
Narrox band (GSM, DCS1800, PCS,
DECT, GPS) Wide band (e.i. 1,3 - 2,8 GHz)
DC injection
8/20s discharge
current capability
Life expectancy
Connedtors
Compatible
Not compatible
Not compatible
10 kA
10 kA
Linked to the GDT stress N, BNC,
TNC, UHF, SMA, 7/16
Linked to the GDT stress
Fonction de la connectique : 100 kA
pour le 7/16, 50 kA pour le N
N, BNC, TNC, F
Illimited
7/16, N, TNC....
The efficiency of coaxial protectors is highly dependent on proper
installation, in particular their connection to the earthing network of the
installation.
Feedthrough mounting
The following installations rules must be strictly observed to insure the
efficiency:
– perfect connection to the bonding network
Equipotential bonding network : all the bonding conductors of the
installation must be interconnected and connected to the installation
earthing network.
Optimized connection of the protector to the bonding network: to reduce
the residual voltages during lightning discharge currents, the connection
of the protector to the bonding network must be as short as possible (less
than 50 cm) and has a proper cross section (at least 4 mm).
Direct mounting of the surge protector on the grounded frame at the installation entrance:
–b
est location (conduction of the surge currents at the entrance of the
installation)
– good mechanical withstand.
Alternative mounting
– c onnection to the bonding network by wire (4 mm minimum and shortest
length possible).
The ’feedthrough mounting‘ versions meet perfectly all these requirements.
Warning: for good contact, remove carefully all paintings or insulating
coatings.
Location of the protectors: they should preferably be placed at the
entrance of the installation (to limit the penetration of lightning currents)
and also near sensitive equipment (to enhance protection).
See our web site for a full catalog: www.navair.com
31
NAVAIR
TECHNOLOGIES
RF Coaxial Protectors
PRC – P8AX – CXP
PRC1800-7/16MF
P8AX25-B/MF
CXP Series
Citel’s PRC Series is a Quarter Wave
Stub (QWS) surge arrestor designed
for specific frequency bands. The PRC
does not utilize any active components
and allows only the specified frequency
to pass thus eliminating low frequency
transients. This design allows for very
high surge handling capacity up to
100kA 8/20us. The PR is conveniently
installed in series with the line and can
be mounted via the standard grounding
screw or bulkhead.
The P8AX series coaxial surge protectors
have been designed to protect antennas,
microwaves, broadband applications,
two-way radios, cellular, GPS and CATV
equipment against lightning surges and
electrical transients. They are a first line of
defense for your sensitive equipment.
The CXP Series has been designed to
protect radio-base communications systems
from lightning and electrical transients.
This device is a dc blocked protector not
to be used where transmitter combining is
performed.
Available with the most commonly
used connectors including BNC, F, N,
SMA, TNC, and 7/16 Din connectors
or it can be custom made for your
application with any combination of
connector and gender types to eliminate
the need for any adapters. .
The P8AX series employs a patented
replacable gas tube, are waterproof
(IP65) and available with three grounding
options: M6 ground screw, bulkhead or
optional mounting bracket.
High-Frequency Surge
Protection
The CXP Series is designed to protect
terminals connected to coaxial cables
against transient overvoltages due to
lightning strikes. The CXP Series is a
combination of Gas Tubes and clamping
diodes which allows a high discharge
current with a low residual voltage and
low insertion losses.
•20kA transient amps protection
(8/20μs)
•5kA transient amps protection
(10/350μs)
•DC Pass to +/-48V
•VSWR < 1.2 Insertion Loss < 0.1dB
•Bi-directional, series installed
•Waterproof
•Removable GDT
See our web site for a full catalog: www.navair.com
32
NAVAIR
TECHNOLOGIES
Android Tablet Test Platform:
• Android Gingerbread
• 7” 800x480 WVGA
• Easy-to-use GUIsys
• USB ports
• Easy Upgrade
• Ethernet & Wi-Fi
• SD card expansion
• Plug & Stay All-in-one
• Rugged Hand-Held
• Test Copper DS0/DS1 to
Fiber10G Ethernet!
GUISYS...meets
State-of-the-Art Android Tablet-PC Test-system
provides a peerless User Experience with exceptional
power and performance.
Why use or lose single function unreliable module
based test sets when you can have so much more
power and capability for a lot less $$$.
Supports Android app’s: Web Browser, Email, Maps, Word,
PDF’s, Excel, Video & Audio, Contacts & Notes, ...and more!
See our web site for a full catalog: www.navair.com
33
NAVAIR
TECHNOLOGIES
Test Platform Features
Full Tablet-PC POWER
Flexible Performance
• Large 7” WVGA Touch-screen
• Landscape & Portrait Modes
• 10/100 LAN port + Wi-Fi support
• 2 USB Host ports & USB OTG
• Browse the Web w/GOOGLE
• Send & Receive Emails
• Supports Multi-media playback
• Supports core Android App’s;
• Google Maps
• State-of-the-Art
• Intuitive, Easy-to-Use Android GUI
• Add ANY of these test services
• Fast Ethernet (10/100)
• Gigabit Ethernet (1000)
• Dual Gigabit Ethernet
• 10Gigabit Ethernet
• DS3
• DS1, Dual-DS1
• E1, Dual-E1
• DataCom
• DS0 Data Services
• DS0-PCM Voice Services
• 2-wire Signaling-TIMS
• 4-wire Wideband TIMS
• PRI-ISDN NT&TE
• 4-wire DDS , Frame-Relay
• CO Timing Analyzer
• Wi-Fi Analyzer
• All-in-one;1 to 16Test Interface!
•C
onfigure your System! As YOU
need it!
• Local & Remote Control
• Notes & Contacts
• Edit & View PDF’s
• Power Point, Excel, WORD
• Training Video’s on the Test Set!
• Transfer Results, Logs & Test files
• Update from anywhere!
• Plug & Stay — no modules to lose!
• AC & Long-Life Lithium DC Power
• 10/100 LAN or RS232
See our web site for a full catalog: www.navair.com
34
• Rack Mountable
• Rugged Handheld Tablet
NAVAIR
TECHNOLOGIES
Navair National Sales/Service Team
Customer Service Programs
Navair Service Solutions
Maximize on your capital product purchasing through an extended service plan
from Navair. Selection of the right plan for your organization allows you to purchase
with confidence knowing you have full support from factory trained technicians.
Direct OEM Warranty Service
Navair is the factory service centre for Bird Electronics, General Dynamics,
­Tele-Instruments. Navair is the only Canadian service centre authorized to
perform factory level modifications ensuring your instruments remain current.
Navair Direct Service
Navair offers product repair, calibration and certified calibration services to ensure
your instruments are maintained to all OEM specifications. Navair staff have
over seventy (70) years combined experience in the Communications, Test and
Measurement Industry a tradition you can depend on. Navair Direct offers the
­following value added services:
• Service Report
• Repair Estimate
• Factory supplied hardware and software upgrades, which enhance your
­instrument ­performance.
• Ninety (90) day warranty on labour and parts replaced
• Direct factory replacement parts to ensure compliance with all OEM
­specifications.
• “Preferred” Customer Status
Place all your instrumentation under an annual or multiple year service agreement
with Navair and enjoy a discounted labour rate on repair.
NAVAIR CALIBRATION SERVICES
Navair is a registered ISO 9002 company with state of the art calibration facilities.
We offer complete calibration services coast to coast on most products sold by
Navair in Canada.
In addition to Navair supplied products, we offer complete calibration services
on Motorola, Wavetek, Helper, Bird, Tektronix, and Agilent products. Our “Depot
Express” ­program was developed with our customers who demand the very best
this industry can offer. As the factory authorized service centre in Canada for Bird
Technologies, General Dynamics and Tel-Instuments products we will ensure full
support for all your Test and Measurement products for yers to come.
“Depot Express” Calibration Service
• Four day turn around on all IFR/General Dynamics calibration
• Certificate of Calibration traceable to National standards
• Pick up and delivery service coast to coast
• Shipping carton available
• Automatic annual recall for calibration
• Instrument loaner available (subject to availability)
A complete "turnkey" operation let our customer service representatives ­manage
your ­calibration requirements as a complete operation from pick up through
final delivery.
MONTREAL/OTTAWA
800-668-7440
Extension 303
TORONTO/MARITIMES
Tel: (905) 565-1583
Fax: (905) 565-8325
VANCOUVER
800-668-7440
Extension 301
NATIONAL SALES SERVICE 1-800-668-7440
Visit us at www.navair.com
Over 35 YEARS of Product & Service Excellence

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project