- Computers & electronics
- Audio & home theatre
- TV set-top boxes
- coship
- Coship 2300
- User manual
- 43 Pages
Coship 2300 satellite receiver settings editor User Manual
Below you will find brief information for satellite receiver settings editor Coship 2300. This manual helps you to understand the features and functions of the program, including how to load and back up settings files, arrange settings, and write settings into your receiver. You can easily make your own channel lists, edit them, print them, and write them into your receiver. You can also enter new channels or transponders, edit, delete, and save them, change the names of channels, sort, search, copy, and paste channels.
advertisement
Assistant Bot
Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.
SetEditCoship2300 for Coship 2300 and compatible
Contents
:
1 General
2 Installation
3 Step by step a Load and back up a settings file b Arrange settings c The favourite list d Channel parameters e Write settings into the receiver f Print or export settings g Using the transponder functions and entering new channels by hand h Import of channels i Other settings and how to convert a settings file
4 Program use and personal configuration
5 Functions a File functions c Channel functions d Satellite functions e Transponder functions
Favourites
6 Problems
7 Register
8 Glossary and abbreviations
1 General
SetEditCoship2300 is a program to change the settings (program sequence, names of channels etc.) of the Coship 2300 and compatible digital satellite receivers.
You can easily make your own channel lists, edit them, print them and write them into your receiver.
You can enter new channels or new transponders, edit, delete and save them, change the names of channels, sort, search, copy and paste channels.
With SetEdit you can edit settings of different receivers, exchange channels between settings files of different receivers or convert a settings file of one format into another (e.g. SetEditDVB2000 into
SetEditCoship2300). If you have other receivers you can add new "modules".
The settings are read from the receiver and written into the receiver via the RS232 interface with a 1:1 cable (serial extension cord, not a null modem cable).
With this program you can also change the receiver firmware.
In the following guide you will find a step by step description of how to use this program. In the other chapters there is a short description of all functions divided in file, channel, satellite, transponder and favourite list functions and the configuration.
2 Installation
System requirements:
PC with Windows 95/98/ME/NT/2000/XP, one free serial port and 20 MB of free disc space.
If you like to install SetEdit for the first time, please start the file
SetEditCoship2300_installation_en.exe.
In this window you can select, if you get in addition to the program a desktop shortcut and an entry in the start menu. Furthermore you can select that after the installation SetEdit is launched and/or the
SetEdit directory is shown in the explorer.
When you click on "Next", you can select the installation directory.
The installation contains the program itself, some pictures and a sample settings file.
If you already have a SetEdit version and simply want to upgrade to SetEditCoship2300, please copy the file SetEditCoship2300.dll in the existing SetEdit directory.
In your SetEdit directory, you will now find the DLLs that are the modules for the different receiver types.
There are no changes made to the Windows system files.
You will also find the file SetEditCoship2300.ini in this directory. Your personal configuration is saved in this file.
To uninstall SetEditCoship2300 simply delete all these files.
If you have more than one receiver (with the right DLL modules), you can decide with which type of
SetEdit the program should start. You just have to change the name of the exe file. Example: If you start SetEditCoship2300.exe after the installation of SetEditCoship2300_installation_en.exe the program will start as a Coship2300 editor. If you change the name of the SetEditCoship2300.exe file into SetEditDVB2000.exe, the program will start as DVB2000 editor. Of course you can open additional SetEditCoship2300 if required.
3 Step by step
I assume that the program has been installed on your PC as described in chapter 2.
Also it is assumed that you are using SetEditCoship2300 for the first time. In the following I will describe how to transfer the settings from the receiver to the PC and back (chapter 3.a and 3.e).
By means of examples you will see how to get order in your settings (chapter 3.b), how to put channels into the favourite list (chapter 3.c), how to work with the transponder menu (chapter 3.g), how to enter new channels by hand (chapter 3.g), how to handle the peculiarities of German Premiere World channels (Formula 1, soccer, pay-per-view) (chapter 3.g), how to adjust settings from other sources to your requirements (chapter 3.h and 3.i) and how to convert one settings format into another (chapter
3.i).
3.a Load and back up a settings file
Please connect your receiver to the PC with a serial extension cord (1:1 cable, not a null modem cable).
If you start SetEditCoship2300 for the very first time you will get a window with the history of the changes from previous versions.
The first thing you should do is to make a backup of the channel settings in your receiver. You can restore such a backup at any time into your receiver and the receiver will be the same as it was at the time you made the backup.
To do this, you have to enter in the configuration the comport you have used to connect your receiver to the PC. Please click on the button "Config."
You will get the following dialogue:
(Here you find three pages. If you are on the page "Colours" or "Convert", please click on "General settings" to get the menu shown above.)
Please enter in the box "Comport" the correct comport.
Then please click on OK.
All other options of this menu are explained in chapter 5.b in details.
Now click on the button "file". You will get the following menu:
Here you select the function "Backup", you get the following window:
In this window you enter the directory and the filename for your backup. (Note: the language of this
window depends on your windows version, so don't worry if you see German buttons here.)
As soon as you have clicked on "save", the following message will appear:
When you have clicked on "OK" in this message, the settings will be read from the receiver and saved on your hard disc.
If you make some unintentional changes in your settings when you experiment with
SetEditCoship2300 you can always restore this backup file into your receiver and reverse any changes.
Now it depends on whether you want to change your own receiver settings with this program or if you want to adapt a settings file that you found on the Internet to your own requirements and write it into your receiver (chapter 3.h or 3.i).
If you want to change your own receiver settings please click on the button "File" and select the menu item "Read from receiver". You get the same message you know from the backup function, so continue as described above.
The settings are now transferred from the receiver to the PC, but this time the settings are not saved, but shown in SetEditCoship2300.
If you want to adapt settings that you found in the Internet to your own requirements and then write them into your receiver, you have to load these settings first. Please click on the button "File", and then select the function "open" from the file menu.
Now please select the file you want to load from the list you see and click on "Open" or double click on the file you want to load.
Note: If you want to write settings that you have found in the Internet into your receiver, you have to be careful:
A settings file does not only contain the channel information, it also includes the LNB and the satellite configuration. These configuration settings will usually not fit to your receiver. Therefore you should better overwrite these configuration settings with your own configuration settings (see chapter 3.i or
5.d.)
When you have loaded a settings file or read the settings from your receiver, you get the following window (depending on the window size and some personal settings the picture may differ).
You see the TV channels (light blue background) and the radio channels (light green background) as well as a transponder list, a satellite list and the favourite list (FAV).
If you select an item in the satellite list, you will see all channels and all transponders that are assigned to this satellite.
If you select a transponder or the favourite list, you will only see the channels that are assigned to this transponder or the favourite list.
When you select a channel, the satellite, transponder and FAV list (if the channel is in the FAV list) of this channel are marked grey.
Transponders marked in red are empty; they contain no channels.
If the channel number is marked with a red background colour, the channel is assigned to a vertical polarised transponder. If the channel number has a white background colour, the channel is assigned to a horizontal polarised transponder.
If a satellite has a green background colour, it is activated, which means there are already channels on this satellite.
(You can change all these marking colours in the configuration menu, see chapter 5.b.)
When you click with the right mouse button in the channel list (TV or radio) and select from the popup menu the entry "Information" you will get the number of TV channels, radio channels and transponders that are in your settings.
3.b Arrange settings
Now you have the settings (from your own receiver or from the Internet) in SetEditCoship2300.
The most important functions will be explained now in detail with some examples, while in the chapter functions all functions are briefly described.
The most important function of SetEditCoship2300 is to get order in your channel list. This can be by deleting channels you don't need (e.g. channels that are scrambled and you have no subscription for), getting the channels into a useful order, assigning the channels to the favourite list and correcting wrong channel settings (e.g. wrong channel names).
First let us suppose that we want to delete a channel. To do this we have to select the channel first.
Please click with the mouse on the channel. Then the satellite, the transponder and the FAV list (if this channel is in the FAV list) of this channel are marked grey in the respective list.
Sometimes it is useful to change this colour (similarly for other colours, for example the colours used for new channels (for the import) or duplicate channels), e.g. because the colours are too pale on a laptop. You will find a description how to do this in chapter 5.b.
Now click with the right mouse button in the channel list and open the channel menu:
Please select the item "delete" in this menu and the selected channel will be deleted from your settings.
If you delete a channel within the favourite list, this channel is only removed from the FAV list but not deleted from the main list.
Note: There is no undo function yet, so be careful.
To delete a channel, you can also select the channel and then hit the Del key on your keyboard.
To delete multiple channels please click for example on channel 5, then press the shift key and keep it pressed and then click on channel 7. The channels 5 to 7 are now selected. Now you can delete these channels as described above.
To select channels that are not consecutive (e.g. the channels 5, 20 and 39) please click on the first channel (here channel 5), then press the Ctrl key on your keyboard, keep this key pressed and then click on the other channels you like to delete.
Now assume we want to move a channel, e.g. ZDF to position 2.
Note: You can show your channel lists in original order or sorted by alphabet, frequency or polarity.
Moving channels is easier when the channel list is shown in its original order. If the channel list is shown in alphabetical order and you move a channel, only the channel number will change but not the position of the channel in the channel list (the name is still the same). To show the channel list in original order, please click with the right mouse button into the channel list and select from the menu
item "View sorted by" the option "Original".
To change the viewing mode of the channel lists you can also click on the letters "O" (original), "N"
(Name), "F" (frequency) or "P" (polarity) in the border of the channel lists.
First we have to find out the position of the channel ZDF at the moment. To find all channels you first have to click on the satellite "all" to see really all channels, independent of the satellite the channels belong to. Then you can search for ZDF by entering the first letters of the channel name. Please click anywhere in the channel list and hit the "Z" key on your keyboard, now all channels whose names begin with "Z" are selected. Now hit the "D" key on your keyboard. Now all channels beginning with
"ZD" are selected. You can do this of course with the third, fourth letter etc. If you wait for more than three seconds between two letters a new search is started, so that the last letter entered is taken as the first letter of the name that is searched.
You can also use the "find channels" function to find channels by name. Open the channel menu and select the function "find channels" from this menu. You will get this window:
You can choose whether you want to search on all satellites or only on the actually selected satellites.
Click on the field beneath "all satellites" to search on all satellites (if you have selected "all" in the satellite list you won't see this option because all satellites are searched anyway).
If you now enter "ZDF" in the field "Name" you will see in the list above all channels whose names begin with "zdf", e.g. the channel ZDFtheaterkanal.
If you click on the white square to the left of the text "substring" you will see all channels that include the entered letters as a part of the channel name (beginning, middle or end, upper/lowercase is ignored). If you enter for example the word "sport" the channel "Eurosport" is found too.
Now you can move channels from this list to another position in the channel list or assign them to another satellite, transponder or the favourite list. The channels will not be removed from the find list, but when you click on such a channel you will see that the new satellite, transponder or the favourite list is now marked in grey.
Within this find function you can also delete channels. Simply select the channel in the list of the find function and hit the Delete key on your keyboard.
Now you have found for example ZDF. There are several ways to move the channel.
The first way is to move the channel by drag & drop: click with the left mouse button on the channel you want to move, keep the mouse button pressed and drag the channel to the position you like to have it. The channel will be placed in front of the position the mouse is on.
To drag a channel on the last position in the list, you have to drag it behind the last channel.
You can also move the channels with the arrow keys of your keyboard. Please select the channel(s) you want to move, then press the Ctrl-key on your keyboard and keep this key pressed. Now you can move the selected channel(s) with the arrow keys on your keyboard. If you press the key "Home" or
"End" while the Ctrl key is pressed you move the selected channel(s) to the beginning or the end of
the list.
With both methods described above you can move of course more than one channel.
Another possibility is to move a channel directly to a position (e.g. channel 20 to position 5). Please select the channel, then click with the right mouse button in the channel list and select from the channel menu you get the function "Move to", the following dialogue appears:
Here you can enter the channel number you like to move the selected channel to (in this example 5).
The selected channel will be moved now in front of the channel that was previously at this position.
If for example KABEL1 had a channel number higher than 5 before, it will be moved to channel 5. If the channel had a lower channel number before (e.g. 3) the channel will be moved in front of the channel that was at position 5. Because one channel is now missing in the list (the channel you are moving) all channels are moved up one position (i.e. to lower numbers), so in this case your channel will be moved to position 4.
Especially if you use the drag & drop method it is often a problem that not all channels can be seen on the screen, so you have to scroll. If you want to move a channel from position 500 to 10 you have to keep the mouse button pressed while you move to position 10. If you move the mouse some pixels up and down at the border of the list, then the list will scroll in this direction.
There are some functions that make moving channels more comfortable. For example you can hide one of the lists (TV or radio) to have more space for the channels. You can even hide the satellites, transponders, the favourite list and the data window. Please call the channel menu and select on
"Show" what you want to see (TV, Radio, TV and Radio, "Show only channels" or "All lists").
If you double click on the name of a channel list the other list will be hidden.
With a second double click on the name you will see both lists again.
When you click on the letter "C" in the border of the channel lists, the satellites, transponders, the favourite list and the data window are hidden. When you click on the letter "A", you will see all lists again.
Another function that makes moving by drag & drop easier is the "split" function. Please click with the right mouse button in the channel list to open the channel menu and select the function "Split" from the popup menu.
All channel lists (depending on what is shown/hidden) are now shown twice. It is of course the same
list, but you have two different views of it. Changes in one of these lists will affect the other list too.
You can move channels from the upper list to the lower list, because it is the same list but from different points of view, the entry is changed in both windows.
If you make many changes to the channels, please remember to save from time to time. To do this hit the "file" button. From the file menu please select the item "save" to save the file. If you want to keep your original file and save the file with a different file name, you should use the "save as" function in the file menu. Enter the file name and click on the "save" button.
With the function "Sort" in the channel list menu, you have several possibilities to sort the channels.
Contrary to the function "View sorted by" the channels are not only shown in a different order, they also get another channel number. You can sort the complete channel list by satellites. This may be helpful if you have got a motorized dish. If you have sorted your channel list by genres for example, your dish would always move between the different satellite positions, when you zap in your channel list.
If you want to sort channels alphabetically, by frequency or polarity, you first have to mark the channels you want to sort.
3.c The favourite list
The Coship2300 receivers usually have more than one favourite list, but with SetEditCoship2300 it is only possible to change the first one because the receiver does not transmit the other favourite lists.
To assign one or more channels to the favourite list simply move the selected channels by drag & drop on the name of the favourite list.
To remove one or more channels from the favourite list you first have to select the FAV list you want to remove channels from. Then select the channels you like to remove and select "Delete" from the channel menu or hit the "Del" key on your keyboard.
When you delete channels from the favourite list, the channels are only removed from the favourite list, but not from the main list.
You can also use the "Mark as" function of the channel list menu to assign one or more channels to the FAV list or remove it/them from the FAV list.
Channels that are in the favourite list are marked in the channel list with a darker background colour.
To change this colour please see chapter 5.b.
You can't change the order of the channels in a FAV list independent of the order of the channels in the main list.
3.d Channel parameters
To rename a channel (e.g. "Das Erste" to "ARD") please select the channel and choose from the channel menu the function "change data" (or double-click on the channel), then you get the channel data menu:
In the field "Name" you can now enter the name of the channel.
Within this menu you can also assign the channel to another LNB.
Furthermore you can change the transponder data (frequency, polarity and symbol rate) the PIDs and the Channel ID of the channel (see chapter 3.g).
With "PIDs" you can choose whether the PIDs are shown decimal or hexadecimal.
You can also mark channels as "scrambled" or "locked" within this menu or remove these markings.
If you lock a channel this means you have to enter the parental pin to watch this channel. These channels will be marked in the channel list with a key symbol. Scrambled channels are marked with the following symbol:
Note: If you remove the scrambled symbol this does not mean that the channel can be watched for free. This is just the marking of the channel.
With the function "mark as" from the channel list menu you can change the following properties for more than one selected channel at once. You can:
-Mark channel(s) as "(un)locked" or "(un)scrambled"
-Assign channel(s) to the FAV list or an LNB or remove it/them from the FAV list
Many channels are only shown in uppercase letters. To change this, you don't have to enter a new name for each channel. Simply select the channels whose name you want to change and select the function "DISNEY CHANNEL -> Disney Channel" from the channel menu.
The first letter of the individual words is never changed by this function. If mixed upper/lower case letters occur in the word, nothing is changed (example: EinsMuXx). Words with less than 4 letters are also not altered, so that abbreviations such as CNN stay unchanged.
In the file SetEdit.ini there are lists of exceptions (which can be changed) to these rules. There is a list of 10 words that are not converted although they contain more than 3 letters, (example: ESPN, CNBC) and a list of 10 words that are converted although they are shorter than 4 letters (example: "CO" so that from KRIMI&CO you get Krimi&Co).
The reasons why you might be interested in changing the channel names to lower case are that mixed-case writing is easier to read and lowercase letters are often narrower than uppercase letters, so that when you have more lower case letters in the channel name more letters can be shown in the channel list of the receiver. Channel names that do not fit within the channel list are truncated.
3.e Write settings into the receiver
When you have finished making your personal settings you have to write them into the receiver before you can use them. To do this, please click on the button "File" and select the function "write into receiver" from the file menu.
You get the following message:
Now click on "OK" in this message and the settings data is transferred into the receiver.
The receiver should be in normal operating mode.
3.f Print or export settings
You can print your settings. To do this click on the "File" button and select from the file menu the function "Print". You get the following dialogue:
First you have to select if your printout should be sorted by channel numbers or by transponders
(frequencies).
If you print your channels in number sequence, you can also select whether you want to print all channels or only the selected ones.
There are some options. You can choose if you also want to print the frequency, the satellite, the
PIDs, if the channel is scrambled or if the channel is in the FAV list, etc.
Finally you can enter the Font height for your printout. Then please hit the button "Print". A printing dialogue will appear, whose layout depends on the printer you have installed.
With the "export" function you can export your settings to a plain ASCII file that can be opened with
Word or Excel or other applications. The tab character (0x09) separates the different parameters.
Besides this the export works the same as printing. Select "Export" in the file menu, then you select the optional parameters as described above and click on the button "Export".
You get a window where you can enter the filename and select the directory of the exported file.
3.g Using the transponder functions and entering new channels by hand
There is a short summary of the transponder functions in chapter 5.e.
Possibly when you read the settings from your receiver you wondered about channels with strange names and that some channels were missing in your list (e.g. German Premiere, soccer, Formula 1 or pay-per-view channels).
Channels that share place (like the German ARTE/Kinderkanal) can only be found in the receiver if they are active at the time you make the channel search. Some of the Premiere Direkt, soccer and
Formula 1 channels are found, but not with the right name.
In the following you find a description how to enter new transponders (and channels) and how to change wrong transponder data.
In the Internet there are sites (e.g. www.lyngsat.com) where you can find all channel settings
(including the missing pay-per-view or soccer channels). In the following you find an explanation how to enter channels and transponders from such lists by hand.
Suppose you discover on www.lyngsat.com that on satellite X a new transponder is active, but your receiver can't find this transponder at the moment, for example because it does not send at the moment (feed) or your antenna is not aligned to this satellite.
Here we see that transponder 12656 horizontal is new and one scrambled TV channel (Anem, the orange background shows you that the channel is scrambled) and two audio channels (B2-92 with two different audio PIDs) are active on this transponder.
Now you have the possibility to create a new transponder first and then enter the channel on this transponder. Or you can directly enter a new channel with the right transponder data on the satellite.
Both methods may be useful, so both will be described in the following:
To create a new transponder, you first have to select the satellite of this transponder. Then you click with the right mouse button in the transponder list and select in the transponder menu the function
"New" -> "Transponder". You see the following window:
For the example mentioned above you enter 12656 for the frequency and HOR for the polarity. The symbol rate in this case is 2963.
The FEC (in this example 3/4) is not used in SetEditCoship2300.
The green numbers in the Lyngsat chart are the NETwork ID and the TS ID (here NET ID = 0 and TS
ID = 176).
These IDs are not used in SetEditCoship2300.
Please confirm with OK then you will find the new transponder at the end of the transponder list.
Now you can enter the new TV and radio programs on this transponder.
To do this select the new transponder and click with the right mouse button in the now empty channel list and select the function "new" from the channel menu you get. You get the following window:
You can also click with the right mouse button in the transponder list (the new transponder has to be selected too) and with "New" you can select the function "TV channel on this transponder" or "radio channel on this transponder".
You will get the same window.
The correct transponder is already entered.
If you want to enter a channel directly, please select the satellite for this channel, click with the right mouse button in the channel list and select the function "New" from the menu you get.
You will get the same window as with the other method again, except that in this case the transponder data has to be entered in the fields "Frequency", "Polarity" and "Symbol rate".
In the field "Name" you can enter the name of the channel (here "Anem").
Then you have to enter the PIDs and the channel ID.
The TV channel "Anem" for example (see list above) has the video PID 4194 and the audio PID 4195.
The channel ID (service ID) is 1 and the PCR PID is as a rule identical to the video PID, so don't forget to enter it!
For the Audio (radio) channels of course no Video PID is given. Usually you use the VPID 1FFF
(hexadecimal) or 8191 (decimal) to indicate that this PID is not used.
The text PID is used for the teletext information.
If you don't find this PID, you can enter 1FFF (hexadecimal) or 8191 (decimal) instead, i.e. "not used".
For "normal" channels you don't need this PID.
When you have entered all the parameters please click on OK and the new channel will appear at the end of your channel list.
As soon as a satellite has one channel it is shown as being active (appears in green). Satellites that have no channel have a white background. (You can change these colours in the configuration.)
Note: In some lists the PIDs are given in decimal notation, in others in hexadecimal notation (see chapter 8). You have to be aware of that when you enter the PIDs. In the configuration menu and in the channel data window you can specify if you want to see/enter the PIDs in decimal or hexadecimal form.
When you enable the option "always on top" in the configuration menu, SetEditCoship2300 will always be in the foreground on your desktop. This can be useful when you work with such Internet lists, as the
SetEdit window will not go into the background when you click in the browser.
You also change the notation of the PIDs if you click on the "H" for hexadecimal or "D" for decimal in the border of the "Info" section.
To compare your settings file with lists in the Internet that are often sorted by frequencies you have the possibility to sort the transponders of your settings file by frequency. To do this click with the right mouse button in the transponder list and select "view sorted by" -> "frequency" from the menu you get.
Alternatively you can also view the transponder list sorted by polarity.
You can also set the viewing mode by clicking on the letters "O" (original), "F" (sort by frequency) and
"P" (sort by polarity) in the frame of the transponder list.
If you want to enter channels that differ only in few parameters, it is useful to create a duplicate of a channel (please use the copy and paste function from the channel menu) and then change only the different parameters.
For German Premiere it is often useful to have channel duplicates. For the sports channels you will find different events (e.g. Champions league, Formula 1, etc.) on the main channels and "special channels". Sport 1 is for example identical to a Formula 1 perspective and a Superdom (soccer) channel. If you like to switch during a Formula 1 transmission between the different feeds it is useful to have all these feeds in one block to prevent from skipping several channels. The same rules aim for champions league and other events.
To create a channel duplicate please click on the channel you like to create a duplicate of, then open the channel menu and select "copy" from this menu. Now select the desired position of the duplicate in the channel list and select "paste" from the channel menu. The original channel and the pasted channel are now marked red to show you that this is a duplicate channel. If you don't want to open the channel menu every time you can also use shortcuts for these functions, Ctrl-C is for copy and Ctrl-V is for paste.
There are two ways to find such a duplicate later:
When you move the mouse over a channel that is marked in red, you get a hint showing the number of a channel that is a duplicate of this channel.
To find such a channel, first click on the channel list, then you can enter the channel number from the keyboard, so if you hit the key "1" channel 1 will be selected, "1" + "4" will select channel 14 etc. As with finding the channels by name, you have to enter the numbers within 3 seconds, otherwise the last entered number is taken as the first digit.
You also have the possibility of using the "Find duplicates" function. Click with the right mouse button in the channel list and select "Find duplicates" from the popup menu you get. You will see the following window:
All duplicates are shown. The different pairs of duplicates are marked in different colours. This function does not distinguish between different types of channels, i.e. it can happen that you see a pair of TV channel duplicates first and then a pair of radio channel duplicates. Relevant for this search are the transponder data and the channel ID, but not the name. If you activate the option "PIDs", the video, audio and PCR PIDs are compared too.
For the "Find duplicates" window there are the same functions as for the "Find channels" window, i.e. you can delete and move channels from this window into another list and select if the duplicates are searched on all satellites or only on the selected satellite.
3.h Import of channels
You have the possibility to get ready-made settings lists from the Internet. These lists can be used partially or completely. You can find such lists for example at the following URLs:
The most current settings lists for the DVB2000 (Nokia 9500/960x) are on www.dxandy.de. It is possible to import channels from these settings into your settings list (especially exotic channels are up-to-date in this list).
On www.lyngsat.com/nokia/index.shtml or on the SatcoDX site (you can find a link on my homepage) you will also find listings of all satellites.
There are three possibilities to use such settings files. In this chapter you find a description how to add some channels from an other settings file into your settings file.
The import function
You can import channels from all settings formats that are supported by SetEdit into your
SetEditCoship2300 settings. In the standard version you can import channels from SetEditCoship2300 settings, DVB2000 settings, Lyngsat DAT charts and SatcoDX SDX files.
You can add other formats by copying the corresponding modules (SetEditXXX.dll) into the SetEdit directory (see chapter 2.)
Please click on "File" -> "New" and select the format of the settings file, from which you want to import channels.
A second window with the chosen settings file will be opened. In the same way you can open a third or even more settings files. Each of these lists is equivalent. Every format (Coship2300, DVB2000,
SatcoDX, Lyngsat or other added formats) has its own symbol.
SatcoDX and Lyngsat files are only Internet lists, so the functions "Read from receiver" and "Write into receiver" do not exist for these formats.
Now you can easily transfer one or more channels by drag & drop from one window into another or
"Copy" and "Paste" them with the corresponding functions from the channel lists menu.
Note: As the Coship2300 receivers only support digital channels you can't import analogue channels.
It may happen, that there are analogue channels for example in a SatcoDX file.
In the configuration of the SatcoDX settings file you can choose, if you only want to see analogue or digital channels or both.
In the different settings formats there are different channel parameters. If a parameter only exists in the destination list but not in the source list (e.g. there are no Text PIDs in the SatcoDX files), a standard value will be taken for this parameter.
You can also drag and drop groups of channels (for example entire transponder with all its channels) from one window into another.
Note: If you import one or more channels into SetEditCoship2300, it may happen that the channel is assigned to the wrong LNB number. Please double click on the imported channel to verify (or change) the LNB number.
Source:
Channel list: The selected channels will be transferred.
All other lists (satellites, providers, labels, transponders, etc): All channels of the selected list will be transferred.
Find window (e.g. "Find channels", "Find duplicates"): the selected channel will be transferred.
Destination:
Channel list: The imported channels will be pasted at the location the cursor is on at the moment you paste the channels. Sometimes it is only possible to paste a channel, if a definitely assignment (e.g. to a satellite) is possible in the destination list. In a SetEditCoship2300 settings list a satellite has to be selected, if you want to paste a channel. If the entry "All" is selected in the satellite list, you can't import channels from another window.
Transponder: A transponder is always definitely assigned to a satellite. So if you assign a channel from another window to a transponder, these channels will be assigned to the satellite of this transponder and will get the transponder data of this transponder.
If you drag and drop a transponder from one window into the transponder list of another window, this transponder with all its channels will be added as a new transponder.
Note: If you import a transponder from another window, this transponder will be added to the satellite that is selected. If "All" is selected in the satellite list, the new transponder will be added to the satellite of the transponder the cursor is on.
If you drag and drop a satellite with all its channels to the transponder list of another window, all these channels will be added to the transponder the cursor is on. This will also happen to channels that come from another FAV list, provider, label, etc.
Note: It may happen that you can't receive a channel, if you assign it to the wrong transponder.
Satellite: The imported channels will be added to the satellite the cursor is on. Transponders that don't exist yet in the transponder list of the destination settings file, will be created.
Favourite list: A direct import into the favourite lists is not possible.
General note: If there is a possible assignment, you can copy channels from each list of one window to each list of another window. For example you can transfer channels from the "Find channels" function of a SatcoDX list to a satellite of a Coship2300 list.
In the popup menu of the channel list there are two functions that may help you to compare the channel lists of different settings files. These functions are only available in the channel list menu, if two or more SetEdit windows are opened.
With the function "Mark new channels in" you can mark in another window the channels that do not exist in your actual list. (The channel number of these channels will be marked in green.)
If more than two lists are opened, you have to select in which list you want to mark the new channels.
If only two windows are opened, only one possibility is given.
With the function "Mark not existing channels in" you can mark in your actual list those channels (the channel number will be marked in red) that do not exist in another window.
If more than two lists are opened, you have to select the channel list that you want to compare your actual list with. If only two windows are opened, only one possibility is given.
With "Remove not existing channel markings" or "Remove new channel markings" you can remove the corresponding markings. These functions will only appear in a channel list menu, if there are such markings in the channel list.
If you have marked the "new channels" or the "not existing channels" in a channel list, you can select them all.
Please click in the channel lists menu on select and choose the corresponding entry: "all not existing" or "all new". This entry will only be shown in the menu, if there are such markings in the channel list.
Note: For the import of channels it is useful, to choose in the configuration the value 5 or even 10 MHz for the frequency tolerance. It may happen that the frequency of the same channel differs just a little bit in different lists. If the frequency tolerance is 0, these channels will be marked as "new" or "not existing" too. But a difference of only some MHz is insignificant to the receiver, so you don't need to import these channels.
3.i Other settings and how to convert a settings file
In the following you find a description how to use a settings file found for example in the Internet completely and how to convert a settings file into the format you need.
Other SetEditCoship2300 settings files
You can load SetEditCoship2300 settings directly into the SetEditCoship2300 main list (with File ->
Open) and then write them into the receiver.
If you like to take settings you find in the Internet completely you may get problems because in addition to the pure channel data also the satellite and LNB configuration are included in the settings file you got from the Internet. It may be possible that you don't want this configuration or that this configuration does not fit to your receiver (LNB configuration). You have the possibility to save your own configuration separately and load it after opening the Internet file into this file.
Please select in the satellite menu "save satellite configuration" to save your configuration, your satellite and LNB configuration is saved on your disc.
If you load a settings file from the Internet, you can use the function "Load satellite configuration" from the satellite menu to overwrite these settings with your previously saved settings.
The satellite configuration of a settings file is saved separately for each satellite. To check it please double-click on the satellite or select "change data" from the satellite menu.
The other functions of this menu are explained in chapter 5.d.
If you often take settings from the Internet but always want to keep your satellite settings, you can enable the option "When loading use personal sat settings" in the configuration menu. Then this part of the settings is always taken from your previously saved configuration.
Convert a settings file
You can convert all settings formats that are supported by SetEdit and for that you have got the corresponding module (in form of a DLL file) into the SetEditCoship2300 format.
In chapter 2 is described how you can add other SetEdit modules.
Please open with "File" -> "New" an additional editor window with the format of the file you wish to convert.
Then please load with "File" -> "Open" the settings file you want to convert into another format.
You can only convert a settings file into the SetEditCoship2300 format, if you have already saved your satellite configuration with the function "Save satellite configuration" in the popup menu of the satellite list (see above). If you want to convert a SetEditCoship2300 settings file into another format, it depends on this format, if you first have to save the satellite configuration for this format or if this is not necessary (e.g. DVB2000, SatcoDX or Lyngsat).
Important: If you convert a settings file only the pure channel and transponder data is taken from the source settings file. The satellite and LNB configuration are taken from the satellite configuration that has to be saved before (see above). If some channel parameters don't exist in the source settings file, a default value is taken for this parameter.
Now you can convert the loaded settings file. To do this, please click on "File" -> "Convert to" and select the format you want to convert this settings file to.
Now you see the loaded settings file in the new format with the corresponding SetEdit version on your screen.
Note: The different settings formats often contain different information, so you will always loose information, when you convert a settings file. If you convert e.g. a SetEditCoship2300 settings file into the SatcoDX format and back, you will see that all favourite channels are gone, because the SatcoDX settings don't have favourite lists. If you convert a SatcoDX settings file into the SetEditCoship2300 format and back, you will recognize, that all analogue channels have disappeared. The Coship2300 receivers only support digital channels. In the same way it may happen that certain PIDs (e.g. the text
PID), volume information or the flags for "Scrambled" or "Locked" get lost.
In the configuration in the menu "Convert" you can enter the options that should be used, if you convert into this format (see chapter 5.b).
If you want to convert another settings file into the SetEditCoship2300 format, you can for example sort the channels by satellites or take the FAV lists from the source list. As the Coship2300 receivers only have one FAV list, all channels that were in any FAV list before, will be assigned to this favourite list.
If you want to convert a SetEditCoship2300 settings file into another format, you have to choose these options in the configuration menu of this other format.
4 Program use and personal configuration
SetEditCoship2300 is mostly used with the mouse. You can also reach many functions with keyboard shortcuts.
On the main window you will find a group of buttons for the general functions ("File", "Config." and
"Help") and the lists that contain the transponders, satellites, the favourite list (FAV) and the channels.
If you hit the right mouse button in the satellite, transponder or one of the channel lists you will get a popup menu with the specific functions for this list.
With "Help" you can open the help file or look for updates of SetEdit.
In some frames you find uppercase letters. If you click on these letters you can change some viewing modes.
You can close every window that comes in SetEditCoship2300 (except the main window) with the Esckey on your keyboard.
In some lists you may find the following red symbols. These symbols indicate:
Scrambled
Locked
If a channel name is marked red there is a duplicate of this channel in the settings.
Transponders marked in red are empty; they contain no channels.
TV channels appear in light blue, radio channels in light green.
Channels that are in the FAV list are marked in the channel list with a darker background colour.
If the channel number is marked with a red background colour, the channel is assigned to a vertical polarised transponder. If the channel number has a white background colour, the channel is assigned to a horizontal polarised transponder.
If a satellite has a green background colour, it is activated, which means there are already channels on this satellite.
When you select a channel, the transponder, the satellite and the favourite list (if the channel is in the favourite list) are marked with a different colour.
You can change all colours in the configuration menu.
In the lower left corner you will find an "Information" section, where you see the parameters of a selected transponder or channel.
When you select a satellite in the satellite list only the transponders and channels that are in that satellite are shown. When you click in a transponder or favourite list only the channels that are in this list are shown.
You can adapt the design of SetEditCoship2300 to your personal wishes.
To change the size of the main window you can either click on the maximise button in the upper right corner or drag one of the margins of the window.
If the main window is large enough, the channel lists can be shown in more than one column. Then you have more channels in view. You can change the width of these columns in the configuration menu on the tab sheet "General settings". In the section "Column width" you can enter if a new column is created, when 100% (auto) or 90-30% of the channels are shown completely. The other channel names are cut.
With "manual" you can enter the column width by hand. Select the function "Setup column width" from the menu of the channel lists and then you can click on the position where you want to have the right border of the first column.
Note: There is a minimum width for the columns. If the window is too small to show more than one column the column width has no effect.
In the section "Cut names" you can enter if the channel name is cut at the end, or if a part of the channel name is cut from the middle.
In the configuration on the tab sheet "General settings" you can change the menu language of SetEdit
(this concerns all opened SetEdit windows) and specify whether the PIDs are shown in decimal or hexadecimal form (see chapter 8).
If you activate on the same tab sheet the option "Show channel count in lists" the number of channels of each satellite, transponder and the FAV list is shown behind the name of this list.
Especially when you want to move channels from the beginning to the end of your list, it may be useful to use the split function. With this function you can split your list into two parts, one showing the beginning and the other showing the end of your settings (see chapter 3.b.)
With a double-click on the frame "TV channels" or "Radio channels" only the choosen channel list is shown. With another double-click on this frame both lists are shown again. With the "show" function of the menu of the channel list you have also the possibility to choose, if you only want to see the TV, the radio channels, or both channel types.
You can also change the viewing mode of the PIDs, if you click on the letters "H" for hexadecimal or
"D" for decimal in the frame of the "Information" section.
For some functions you also have shortcuts for keyboard using:
Ctrl-O: Open a settings file
Ctrl-S: Save settings
Ctrl-R: Read settings from the receiver
Ctrl-W: Write settings into the receiver
Ctrl-P: Print settings
Ctrl-E: Export settings
Alt-R: Show only radio channels
Alt-T: Show only TV channels
Alt-A: Show TV and radio channels
Ctrl-0 (zero): Load the last used file
F1: Help
F2: Satellite list
F3: Label list
F4: Transponder list
F5: Provider list
F6: FAV list
F7: TV list
F8: Radio list
F10: Configuration
F11: Toggle between "Show only channels" and " Show all information"
Depending on the editor you are using, some lists are not available, for example the DVB2000 has no satellite list.
To close a SetEdit window please click on the "close" button: or select "Close" from the "File" menu. If only one editor window is opened you close the complete program.
If you select "Exit" from the "File" menu all open editor windows are closed. In the configuration you can enter with "Restore last session when starting" that all opened editor windows are restored when you start the program the next time.
When you like to use this function you have to finish from SetEdit with the "File" -> "Exit" function. If you close all windows one by one only the last opened window will be restored.
Note: If you have unsaved changes you are asked if you want to exit or first save these changes.
5 Functions
5.a File functions
To get the file functions, please click on the "File" button. You will get the following popup menu:
With New you can open another window of SetEdit with the same or another format, e.g. for the import of channels or if you want to compare different channel lists (see chapter 3.h.)
With Open you can load settings from your disc.
With Last files you get a list of the 10 last used files, which you can load.
With Clear last files list you can remove all entries from the last files list.
With Read from receiver you can read the settings from your receiver into SetEditCoship2300. You get a message on your screen. When you have clicked on "OK", the settings are read from the receiver and shown in SetEditCoship2300.
The receiver should be in normal operating mode.
With Backup you can transfer the settings from the receiver directly to your hard disc without having them in SetEdit. You will first get a window where you can enter the directory and the file name.
Otherwise the procedure is similar to "Read from receiver".
With Save or Save as you can save the current settings to your disc.
With Write into receiver you can transfer the settings from SetEditCoship2300 to your receiver. You also get a message. When you have clicked on "OK", the settings are written into the receiver.
With Restore you can transfer settings from your hard disc directly to your receiver. First you get a window where you can select the file you like to transfer into the receiver. Otherwise the procedure is similar to "Write into receiver".
With Convert to you can convert your actual loaded settings file into another settings format (e.g.
SatcoDX). If you want to convert another settings format (e.g. SatcoDX) into the SetEditCoship2300 format you first have to open a new editor window (with File -> New) with the corresponding SetEdit format (e.g. SatcoDX) and then you can load the Settings file you want to convert in this editor window. To do this you first have to save your satellite configuration (see chapter 3.i).
With Print you can print your settings.
You have two ways of printing your settings. You can either sort the list by the channel numbers (to have a printed channel list) or by the transponders of the channels (to compare your settings with lists in magazines).
If you print your channels in number sequence, you can also select whether you want to print all channels or only the selected ones.
The channel number and name are always printed; additionally you can print the transponder data
(frequency, symbol rate and polarity), the satellite, the PIDs, the Channel ID and the flags for
"scrambled" or "FAV".
In the field "Font size" you can enter the size of the font that is used for printing. If more than one column will fit on the page you will get a multi column printout.
With Export you can export your settings as an ASCII file (e.g. to open it with Word). You have the same options as with the print function.
With Close you close the actual active SetEdit window. If only one window is opened you close the complete program.
With Exit you exit from SetEdit. All open editor windows are closed. In the configuration you can enter with Restore last session when starting that all opened editor windows are reopened when you start the program the next time.
When you like to use this function you have to finish from SetEdit with the "File" -> "Exit" function. If you close all windows one by one only the last opened window will be restored.
5.b Configuration
Click on the "Config." button to change the general settings of SetEdit. There are three tab sheets in the configuration menu.
General settings:
If you click on "General settings" you get the following menu:
In the field Comport you can select which comport of your PC is used to connect to your receiver.
The value Frequ. Tol. (Frequency tolerance) is used when importing and indicates the tolerance a transponder frequency may have relative to the imported one to be considered to be the same. If you have for example a transponder with the frequency 11721 MHz in you settings and you import a channel with the frequency 11720 MHz and the frequency tolerance is set to 5 MHz no new transponder is created. This tolerance is also used for the transponder list.
With Column width you can select if 100% (auto) or 90-30% of all channels have to fit completely to a column. All other channel names are truncated. With "manual" you can enter the column width by hand. Please select the function "Setup column width" from the menu of the channel lists and then you can click on the position where you want to have the right border of the first column.
Note: There is a minimum width for the columns. If the window is too small to show more than one column the column width has no effect.
In the field Cut names you can enter, if channel names that are too long (see column width), are cut at the end or in the middle.
In the field PIDs you select how the PIDs are shown/entered (decimal or hexadecimal). You can also switch between these two viewing modes, if you click on the "H" for hexadecimal or the "D" for decimal in the frame of the "Information" section.
With Language you can select the menu language you would like. This language is taken for all opened SetEdit windows.
With Always on top SetEditCoship2300 always stays on top of your desktop.
With Start with last used file SetEditCoship2300 opens automatically the last used file every time you start the program.
With When loading use personal sat settings you can, after you have once saved your satellite configuration (see chapter 3.i), use this configuration automatically when loading settings. For example you can use your satellite settings always when you load settings from other sources.
If Restore last session when starting is activated, all editor windows that were opened when you closed the last session are reopened (see chapter 5.a.)
If you activate Show channel count in lists the number of channels of each satellite, transponder and the favourite list is shown behind the name of these lists.
Colours:
If you click on the tab sheet "Colours", you will get the following menu:
Here you can change the colours that are used to mark the following states:
Activated (programmed) satellites
Horizontal polarised transponders, vertical polarised transponders
TV channels and radio channels
TV or radio channels that are in the favourite list
Transponder, satellite and FAV list of an actually selected channel (Active Tr/Sat/FAV)
Channel duplicates
Empty transponders
New or not existing channels (for the import function, see chapter 3.h)
The icons for "locked" and "scrambled"
With a double click on the frame of a colour field, you get the default colour again.
Convert:
On the tab sheet "Convert" you can choose which options should be used, if you convert another settings file into the SetEditCoship2300 format.
Sort channel list by satellites: The channels of the source list will be sorted by satellites, when you convert into the Coship2300 format.
Convert FAV lists to satellites: All FAV lists of the source list will be converted to satellites. All satellites that have the geographic position 0.0° east/west and that are empty are converted to a FAV satellite (the satellite configuration that you have saved before should of course contain such empty satellites).
Note: If you want to use this function it is important that each FAV list of the source list only contains channels of one satellite.
To make a satellite empty there is the function "clear" in the satellite menu (see chapter 5.d.)
This option may be useful for example if the source list has more than one FAV list and you want to keep all favourite lists.
Take FAV list(s) from source list: All FAV lists will be taken from the source list. As the Coship2300 receivers only have one FAV list, all channels that were in any FAV list before, will be assigned to this favourite list.
If you want to convert a SetEditCoship2300 settings file into another format, you have to choose these options in the configuration menu of this other format. Depending on the receiver there can be up to
10 different options.
5.c Channel functions
Please select the channels you like to edit/modify.
You get most functions when you click with the right mouse button on a channel list. You will get the popup menu of the channel list:
Some menu items are only visible, when you are using the import functions.
Info: here you get the number of TV and radio channels and transponders that are in your settings.
With Show you can change the viewing mode of SetEditCoship2300. You can select if you only want to see the TV or the radio channels or both.
Note: Alternatively you can double-click on the TV/Radio frame to change the viewing mode.
Furthermore you can hide the satellites, transponders, the favourite list and the data window with
Show only channels. With All lists you can see all lists again.
With View sorted by the channel list can be shown in the original order, sorted alphabetically or sorted by frequencies or polarities.
With Change channel data you get the following window where you can change the properties of a channel:
In the field Name you can change the name of the channel.
You can enter the PIDs, the Channel ID and the transponder data of the channel and enter, if the channel is locked (you have to enter the parental PIN) or scrambled.
With PIDs you can choose if the PIDs are shown decimal or hexadecimal.
With LNB you can change the LNB of the channel.
You can find a longer description of the different PIDs, IDs and transponder data in chapter 3.g.
With Delete you can delete selected channels or, when you are in the FAV list, remove them from this favourite list.
You can also delete one or more selected channels by hitting the Del key on your keyboard.
With Copy you can copy a channel, then you can paste the channel to another position.
With Paste you can paste a channel that was previously deleted or copied.
With Move to you can move a channel to a position that you enter with the keyboard.
With Select you can select all, all scrambled, all locked, all C-band channels or (for the import) all
new or all not existing channels (depending on which channels are actually marked).
With Invert selection you can invert the selection, the channels that are selected will become unselected and vice versa. If you like to delete all but one channel from a transponder, you can select the channel you like to keep, invert your selection and delete the now selected channels.
With Mark as you can change the following properties for one or more selected channels at once:
-Mark channel(s) as "(un)locked" or "(un)scrambled"
-Assign channel(s) to the FAV list or an LNB or remove it/them from the FAV list
Mark new channels in: If you have opened more than one window of SetEdit (Import), you can mark in another channel list the channels that you don't have in your actual channel list.
Mark not existing channels in: If you have opened more than one window of SetEdit (Import), you can mark in your actual channel list the channels that you don't have in another channel list.
Remove new/not existing channel markings: With this function you can remove the markings for new or not existing channels in your actual list (Import).
With Sort you can sort selected channels by alphabet, by frequency or by polarity or sort the entire channel list by satellites.
With DISNEY CHANNEL -> Disney Channel you can change the names of the selected channels from upper case to lower case. Uppercase letters are usually wider than lower case letters, so this allows you to see more characters of the name in the channel list of the receiver. Only words with more than 3 characters are converted. If there are both upper and lower case letters in the channel name the word is not converted (e.g. EuroSport stays as it is). In the configuration file of
SetEditCoship2300 (SetEdit.ini) there is a list of up to 10 words that are converted although they are shorter than 4 letters (CO, INT, FOX) and a list of words that are not converted although they are longer than 3 letters (CNBC, ESPN).
With Find channels you can find channels by name.
With Find duplicates you can look for channel duplicates.
With New you can create a new channel.
With the Split function you can tile the TV and radio list in two parts. It is the same list but from two points of view. Changes in one list also affect of course the second list. You can move a channel from
the upper to the lower list of course.
The function Setup column width is only visible in this menu, when you have entered "manual" in the section "Column width" in the configuration menu (see chapter 5.b). With this function you can enter the column width by hand. Please select this function and then you can click on the position where you want to have the right border of the first column.
Note: There is a minimum width for the columns. If the window is too small to show more than one column the column width has no effect.
To move channels you simply drag them with the mouse to the position where you want them to be (if you reach the border of a list the list will scroll automatically).
To assign one or more channels to a satellite, transponder or the favourite list drag it/them with the mouse to the name of the satellite, transponder or favourite list.
To see all channels of a satellite, transponder or the favourite list, please click in the respective list on the corresponding entry.
In the frame of the channel list there are several uppercase letters for the following functions:
A: The channels and the satellites, transponders, FAV list and the data window are shown.
C: Only the channels are shown.
O: The channels are shown in original order.
N: The channels are shown in alphabetical order.
F: The channels are shown sorted by frequencies.
P: The channels are shown sorted by polarities.
5.d Satellite functions
When you click on a satellite only the channels and transponders of this satellite are shown.
When you click with the right mouse button in the satellite window you will get the following popup menu:
Show active satellites/Show all satellites:
With this function you can select if you want to see all satellites in the satellite list or only the active satellites (satellites which already have channels).
Change data:
You will get the following window in which you can change the satellite-specific data:
You can also double-click on the satellite to get this.
Here you can change the Name and the geographical position (longitude) for this satellite.
View sorted by:
With this function you can select if the satellites are shown in original order, or sorted alphabetically or by the geographical position (longitude).
With Clear you can clear a satellite. All channels and transponders are deleted and the geographic position is set to 0.0° east. This is useful if you want to use the convert option "Convert FAV lists to satellites" (see chapter 5.b).
Save satellite configuration:
With this function you save the satellite and LNB configuration of the actual loaded settings file (see chapter 3.i.)
Load satellite configuration:
With this function you can overwrite the satellite and LNB configuration of the actual settings with a configuration you saved before. In the configuration menu you can enter that this is done automatically when you load a file.
For each LNB number (1-16) you can enter the LOF high/low, the LNB type, the dish type and the parameters for 12 V, 22 kHz and DiSEqC.
In the frame of the satellite list there are several uppercase letters for the following functions:
A: Show all satellites
P: Show only active (programmed) satellites
O: Show satellites in original order
N: Show satellites sorted by alphabet (names)
L: Show satellites sorted by their geographical position (longitude)
5.e Transponder functions
If you select a transponder only the channels that belong to this transponder are shown.
If you select "All" in the satellite list you can move the mouse over a transponder to see the satellite of this transponder.
You get most functions if you click with the right mouse button on the transponder list. You will get the popup menu of the transponder list.
With View sorted by you can select if the transponders are displayed in their original order or sorted by frequency or polarity. The transponders will remain in the original order internally.
With Change data you can change the parameters of a selected transponder. You get the following window:
You can also call this function with a double-click on a transponder. Here you can change the
frequency, the polarity and the symbol rate of a transponder. These changes are made for all channels that use this transponder too.
With Delete you can delete a transponder and all its channels. You can also use the Del key on your keyboard. If the transponder has channels, you are asked if you really want to delete these channels.
If you want to delete a transponder without checking if existing channels are deleted too, you can use the shortcut Ctrl-Del.
With Delete all empty transponders you can delete all transponders that don't contain channels.
With New you can create a new transponder or a new TV or Radio channel on the selected
transponder.
If you want to create a new transponder, and a satellite is selected in the satellite list, the transponder is assigned to this satellite. If "All" is selected in the satellite list and a transponder is selected in the transponder list, the new transponder is assigned to the satellite of this selected transponder. If "All" is selected in the satellite list and no transponder is selected, you can't create a new transponder.
In the frame of the transponder list there are several uppercase letters for the following functions:
O: The transponders are shown in original order.
F: The transponders are shown sorted by frequencies.
P: The transponders are shown sorted by polarities.
5.f Favourites
The Coship2300 receivers usually have more than one favourite list, but with SetEditCoship2300 it is only possible to change the first one because the receiver does not transmit the other favourite lists.
Channels that are in the FAV list are marked in the channel list with a darker background colour.
(You can change these colours in the configuration.)
Add/remove a channel to/from the FAV list:
To add one or more channels to the FAV list, please select the channel(s) you want to add to the FAV list. Now you can drag them to the FAV list (drop them on the name of the list). They are added at the end of this FAV list.
To remove a channel from the FAV list, please select the FAV list and then the channel that you want to remove from the favourite list and use the delete function of the channel list menu or hit the Del key on your keyboard. If you delete a channel within the FAV list, this channel is only removed from the
FAV list and not from the main list.
It is also possible to assign one or more channel(s) to the FAV list or remove them from the FAV list with the help of the "Mark as" function in the channel list menu.
You can't change the order of the channels in the FAV list independent of the order of the channels in the main list.
Note: It is not possible to change the name of the FAV list; it is hard coded in the receiver.
6 Problems
If you have problems with the serial connection please check your serial cable. It has to be a serial 1:1 cable (no null-modem cable) with the following pin connections:
2-2
3-3
4-4
5-5
6-6
7-7
8-8
SetEditCoship2300 is only tested with the original version of the receiver firmware. If you have changed the receiver firmware, I can't guarantee that the program will work properly.
For some Coship2300 Receiver you have to make a factory reset after writing the settings into the receiver. Otherwise the receiver will still use the old settings.
It is only possible to convert another settings file into the SetEditCoship2300 format, if you have saved the satellite configuration before (see chapter 3.i).
If you have any other problems please feel free to contact me by e-mail. Please note for all problems the exact version of SetEdit you use (see Help -> About SetEditCoship2300).
My e-mail address is [email protected]
Please don't call me to tell me about problems. There is no phone support.
7 Register
You can get your registration key for 19,99 € from me. I need your full name and your e-mail address. I can't send you the registration key by post.
In the demo version you can only change 20 channels. After this you can neither save your settings nor write them into your receiver.
Note: Without your e-mail address and your full name I can't register you for
SetEditCoship2300.
To register for SetEditCoship2300 there are 4 possibilities:
1. You send me the money in cash (by registered letter).
My address is:
Wolfgang Litzinger
Wasseraecker 8
67705 Trippstadt/Germany
2. You can make a direct money transfer.
Note: If you transfer from outside Germany please make sure that you pay the fees for international money transfer.
My account is:
Account number 44 609 52 00
Bank name: Bank 24
Sort code: 380 707 24
Bank address:
P.O. box 24
Karl-Legien Str. 188
53244 Bonn/Germany
SWIFT: DEUT DEDB XXX
IBAN: DE66 3807 0724 0446 0952 00
Please use as the reason for payment your name, the editor version you wish to order and add a random number (e.g. your zip code, phone number etc.).
Example for a reason for payment: Charles Brown SetEditCoship2300 12:56
Please send me an e-mail when you have transferred the money. The body of the mail should contain your name, the editor version you wish to order (here SetEditCoship2300) and the random number you wrote in the reason for the money transfer.
Example for an e-mail text: Order for SetEditCoship2300, Charles Brown, 12:56
Please check if you e-mail address is valid (e.g. by sending an e-mail to your own address).
Unfortunately it happens sometimes that I want to send someone an e-mail with the registration key but the e-mail comes back undeliverable because the return address is not correct.
Please make sure that your name is in the e-mail (there are often e-mails like "from: [email protected], I have sent you money today please sent me the editor"). In this case I can't relate your mail with my bank account.
Please don't try to write your e-mail address to the reason of the money transfer, special characters like "@" and "_" are not valid for this.
Please don't sent me pictures of your transfer sheet or online banking program, you will get the
key as soon as I have the money on my bank account, I check my account every day.
If you get no e-mail from me after 7 working days, please contact me by e-mail. Either I could not assign your money transfer to someone or something is wrong with your e-mail address.
3. The easiest way to pay from outside Germany is to pay by credit card (Visa/MasterCard or
American Express). Please use the order form on the next page, print it and fill out all fields and then send it to me by fax +49 (0) 6306 993453.
4. You can also use the online shop on my homepage to pay by Visa/MasterCard.
Back to Contents.
Order for SetEditCoship2300
(Please write in block letters, faxes are often hard to read!)
Date: _________________
From:
First name: ___________________________
Last name:
E-mail:
Note: if you don't get a reply within 3 working days I couldn't read your mail address or the address was not valid, please sent me a mail so I can see your correct mail address.
Street:
ZIP code:
___________________________
___________________________
___________________________
___________________________
City: ___________________________
Country: ___________________________
Fax: ___________________________
To: Wolfgang Litzinger
Company: SetEdit
Fax number: +49 (0) 6306 993453
Visa/MasterCard American
Card number: _ _ _ _-_ _ _ _-_ _ _ _-_ _ _ _
Expire date: _ _/_ _
3 _ _ _-_ _ _ _ _ _-_ _ _ _ _
I have tested the demo version of SetEditCoship2300 successfully and allow you to charge 19,99 Euro from my credit card.
Signature: ____________________
8 Glossary and abbreviations
Baud rate: The speed at which data is transferred via the serial port to the receiver. The number is in bits per seconds.
Decimal/Hexadecimal: Hexadecimal is a system for representing numbers in base 16, rather than the base 10 we normally use. The hexadecimal system requires 15 digits and a zero; conventionally the letters A-F are used to represent the digits for that the decimal system cannot provide equivalents.
Hexadecimal notation is not usually important for the PC user (with the possible exception of specifying base addresses) but is still quite important for the programmer. Its importance arises because there is a very close correspondence between hexadecimal and the very important binary numbering system that computers use internally. However, hexadecimal notation is much more compact than binary.
The reason why you can select both systems in SetEdit is that many satellite operators use "even" hexadecimal PID numbers. For example the audio PIDs on Astra transponder 11720 are in decimal notation 256, 512, 768, 1024, 1280 etc., whereas in hexadecimal notation they are 100, 200, 300, 400 etc.
DLL: Dynamic Link Library. A Windows library file that can be shared by multiple applications.
FEC: Forward Error Correction. A system, in which redundancy is added to the message so that most errors can be corrected dynamically at the receiver. Usual values are 1/1, 1/2, 2/3, 3/4, 5/6 and 7/8.
3/4 means that 3 out of 4 bits are reference data and the remaining one is for error correction.
LNB: Low Noise Block (converter). Amplifies received signals and converts them from microwave to lower frequency signals that are then sent along a cable to the satellite receiver. An LNB can be either single or double. A double LNB is required when more than one receiver is used allowing the viewing of different satellite channels on other television sets.
PID: Program Identifier. A 13-bit code in the transport packet header. PID 0 indicates that the packet contains a PAT PID. PID 1 indicates a packet that contains CAT. The PID 8191 (all 1 bits) indicates null (stuffing) packets. All packets belonging to the same elementary data stream have the same PID.
The most important PIDs are the Video PID (for the video information), the Audio PID for the sound and the PCR PID (Program clock reference) to get Video and audio synchronous.
If you enter an existing Service ID for a channel, the receiver can get all necessary information for this channel. If you only enter the video and the audio PID, it may happen that you see the picture and hear the sound, but EPG does not work because this information is transmitted on a different PID.
Usually the receiver finds the PIDs automatically, but occasionally (exotic channels) you have to know them and enter them by hand.
Symbol rate: The amount of digital data that is transmitted per second via a transponder. This is specified in Msymb/sec (Mega symbols per second), whereby a "Symbol" consists of 4 bits. The symbol rate together with the FEC value can be used to calculate the bandwidth of a transponder.
Polarity: A satellite transmission signal has either a vertical, horizontal, or circular orientation; a satellite can be all vertical or all horizontal; if a satellite is cross polarised, it can transmit both ways and therefore has twice the delivery capacity.
Besides the horizontal and vertical polarisation we also find the circular polarisation. Circular polarisation is not as easy to understand as linear polarisation, you can imagine that the waves are rotating clockwise or anticlockwise. In this case we speak about LHC and RHC (left hand circular and right hand circular).
As a rule in Europe linear polarisation (horizontal and vertical) is used. In Scandinavia and for C-band reception circular polarisation is used.
Select: To select a channel please click with the mouse on the channel. To select more than one channel you can use the usual windows methods.
When you press the shift key and click on a channel all channels between the currently selected and the last selected channel are selected.
If you press the Ctrl key on the keyboard you can add single channels to your selection.
Settings are the part of the memory of your receiver where all channel information is stored.
It contains all channel information such as sequence, channel name, frequency, symbol rate, FEC, and all other parameters.
advertisement
Key Features
- Load and back up receiver settings
- Arrange receiver settings
- Write settings into the receiver
- Edit channel lists
- Enter new channels and transponders
- Import channels from other settings files
- Convert settings files between different formats
- Print and export settings
- Change receiver firmware