Baumatic PCG9110SS cooker

Baumatic PCG9110SS cooker
PCG9110SS 90cm
Single cavity gas
cooking theatre
bThat
1
User Manual for your Baumatic
PCG9110SS
90 cm Single cavity gas cooking theatre
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
GS 12/05/10
2
Contents
Environmental note
4
Important safety information
5–9
Specifications
Control panel
9 – 10
11
Using your gas cooking theatre
Before first use
Switching the gas oven on
Switching the gas grill on
Using and assembling the rotisserie
Using the minute minder
The oven light
Cooking guidelines
Warnings
Using the hob top
Automatic electric ignition with flame failure safety device
Energy saving tips
12–18
12
12–13
13–14
14–15
15
15
16
16
17
17
18
Cleaning and maintenance
Cleaning the hob burners
Replacing the oven bulb
Removing the oven doors for cleaning
19–21
20
20
21
Installation
Positioning
Gas connection
Ventilation requirements
Gas Safety (Installation and Use) Regulations
Gas connection
Gas adjustment (Conversion to LPG for the hob top)
Minimum flow adjustment for hob gas taps
Gas adjustment (Conversion to LPG for the oven and grill)
Minimum flow adjustment for the oven and grill burners
Fitting a stability chain
Electrical connection
Connecting the mains supply cable
Replacing the mains supply cable
22–35
22–24
24–25
25
26
26–27
28
29
30–31
31
32
33
34
34–35
My appliance isn’t working correctly
35–36
Contact details
37
3
Environmental note
o The packaging materials that Baumatic uses are environmentally
friendly and can be recycled.
o Please discard all packaging material with due regard for the
environment.
4
Important safety information
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If you
are unsure of any of the information contained in this
booklet, please contact the Baumatic Advice Line.
General Information
o This appliance is designed for domestic household use and for
the cooking of domestic foodstuffs.
o IMPORTANT: The adjacent furniture and all materials used in
the installation must be able to withstand a minimum
temperature of 85°C above the ambient temperature of the
room it is located in, whilst in use.
o Certain types of vinyl or laminate kitchen furniture are
particularly prone to heat damage or discolouration at
temperatures below the guidelines given above.
o Any damage caused by the appliance being installed in
contravention of this temperature limit, or by placing adjacent
cabinet materials closer than 20 mm to the appliance, will be
the liability of the owner.
o For use in leisure accommodation vehicles, please refer to
the appropriate information given in the installation instructions
for this appliance.
o IMPORTANT: Baumatic Ltd. DO NOT recommend that this
appliance is installed on any type of marine vessel.
o The use of this appliance for any other purpose or in any other
environment without the express agreement of Baumatic Ltd.
will invalidate any warranty or liability claim.
o Your new appliance is guaranteed against electrical or
mechanical defects, subject to certain exclusions that are noted
in Baumatic’s Conditions Of Guarantee. The foregoing does not
affect your statutory rights.
o Repairs may only be carried out by Baumatic service
engineers or their authorised service agent.
5
Warning and safety instructions
o This appliance complies with all current European safety
legislation. Baumatic do wish to emphasise that this compliance
does not remove the fact that the appliance surfaces will
become hot during use and retain heat after operation.
Child Safety
o Baumatic strongly recommend that babies and young children
are prevented from being near to the appliance and not allowed
to touch the appliance at any time. During and after use, all
surfaces will become hot.
o If it is necessary for younger family members to be in the
kitchen, please ensure that they are kept under close supervision
at all times.
General Safety
Make sure that you understand the controls before using the
appliance.
Check that all of the controls on the appliance are turned off
after use.
Always stand back when opening the oven door, this will allow
heat to disperse.
Take care when removing items from the oven, as the contents
may be hot.
Always keep the oven doors closed when the oven is not in use.
Always follow the basic principles of food handling and hygiene;
this will prevent the possibility of bacterial growth.
Always keep ventilation slots clear of obstructions.
Keep fingers away from the hinge areas when closing the door,
otherwise you may trap them.
Oven gloves should be used when placing food in the oven cavity
and when removing it. Care should be taken to avoid direct
contact with the inside of the appliance.
o DO NOT LEAVE THE APPLIANCE UNATTENDED WHILST IN
USE.
6
o Do not place heavy objects on the oven door or lean on the
oven door when it is open, as this can cause damage to the oven
door hinges. Nobody should be allowed to sit or stand on any
part of the cooker.
o Do not store chemicals, food stuffs, pressurised containers in or
on the cooker or in cabinets immediately above or next to the
cooker.
o Do not heat up unopened food containers, as pressure can build
up which may cause the container to burst.
o Do not place flammable or plastic items on or near the hob
burners, these types of materials should also not be placed in
the oven or the compartment below the oven.
o Do not leave heated oil or fat unattended, as this is a fire risk.
You should not fill a deep fat frying pan more than one third full
of fat or oil; you should also not use a lid.
o Do not allow fat or oil to build up in the oven trays, grill pan or
oven base.
o Do not place pans or baking trays directly on the base of the
oven cavity, or line it with aluminium foil.
o Do not grill food containing fat without using the grill trivet. The
grill trivet should never be covered with aluminium foil.
o Do not place hot enamel parts in water, leave them to cool first.
o Do not allow vinegar, coffee, milk, saltwater, lemon, tomato
juice or any liquid with high sugar content to remain in contact
with the enamel parts of the appliance. Spillages should be
wiped up immediately.
o Do not allow electrical fittings or cables to come into contact
with areas on the appliance that get hot.
o Do not use the appliance to heat the room it is located in or to
dry clothing. No clothing should be placed over or near to the
hob burners or oven door.
o Do not install the appliance next to curtains or soft furnishings.
7
o Do not attempt to lift or move cooking appliances by using the
oven door or handle, as this may cause damage to the appliance
or result in injury to the person lifting the appliance.
Cleaning
o Cleaning of the oven should be carried out on a regular basis.
o Great care should be taken whilst using this appliance and when
following the cleaning procedure.
o IMPORTANT: The appliance must be disconnected from the
mains before following the cleaning procedure.
o IMPORTANT: Care must be taken when cleaning between
the door glasses, and inside the inner frame as some of
the edges maybe sharp due to the manufacturing process.
Installation
This appliance must be correctly installed by a
suitably qualified person, strictly in accordance
with the manufacturer’s instructions. Please see
the specific section of this booklet that refers to
installation.
o Baumatic Ltd. declines any responsibility for injury or
damage, to person or property, as a result of improper
use or installation of this appliance.
o Heat, steam and moisture will be created during use of the
appliance, take care to avoid injury and ensure that the room is
adequately ventilated. If the appliance is going to be used for
prolonged periods of time, then additional ventilation may be
required.
o Please consult with your qualified installer if you are in any doubt
about the amount of ventilation that you will require.
Declaration of conformity
This appliance complies with the following European Directives:
-73/23/EEC
regarding “low voltage”
-89/336/EEC regarding “electromagnetic disturbances”
-90/396/EEC regarding “gas appliances”
-89/109/EEC regarding “materials in contact with food”.
8
o The above directives comply with 93/68/EEC regarding CE
marking.
o The manufacturer declares that the oven is built using certified
materials and requires the appliance to be installed in
accordance with the standards currently in force. This appliance
must be used by a trained person for domestic purposes only.
Specifications
Product dimensions:
Height: 870 - 920 mm
Width: 898 mm
Depth: 600 mm
Product specifications:
o
o
o
o
o
o
o
5 burner gas hob:
1 x 3.60 kW wok burner
1 x 3.00 kW rapid burner
2 x 1.75 kW semi-rapid burners
1 x 1.00 kW auxiliary burner
Heavy duty cast iron pan stands
Underknob auto-ignition
o Main oven: gas oven with grill
o Main oven capacity: 117 litres
o Storage compartment capacity: 35 litres
o
o
o
o
o
Minute minder
Cooling fan
Flame failure safety device in the oven and grill
Double glazed removable door
Adjustable feet
9
Standard accessories:
o
o
o
o
o
o
o
Enamelled drip tray
Safety shelf
Rotisserie skewer with removable handle
Motorised turnspit
LPG conversion jets
Trivet
Wok stand
Optional extras:
o BPS1 Pizza stone
o BTGRID Double-sided griddle plate
Electrical details
Rated Voltage:
230 Vac 50 Hz
Supply Connection:
13 A (double pole switched fused
outlet with 3mm contact gap)
Fuse Rating:
3 amp
Mains Supply Lead:
3 x 0.75 mm²
Gas details
Gas Connection Type:
Gas Type (Natural Gas):
Gas Type (LPG):
1/2” BSP
20 mbar
See tables on page 28 and 30 for
this information.
For future reference please record the following information which can
be found on the rating plate and the date of purchase which can be
found on your sales invoice. The rating plate for your oven can be
located by opening the door of the storage compartment.
Model Number
……………………………….
Serial Number
……………………………….
Date of Purchase
……………………………….
10
Control Panel
Main oven and grill control knob
o Use this control knob to light and set the
temperature of the main oven. It should
also be used to light the grill in the main
oven.
Hob control knobs
o Use these control knobs to light and control
the hob burners.
Minute minder control knob
o Use this control knob to set the minute
minder countdown.
11
Using your gas cooking theatre
Before first use
o To remove any residue from the oven cavity that may have been
left from the manufacturing process, you should select the gas
oven and set it to its maximum setting.
o It is perfectly normal for a smell to be produced during this
process.
o You should make sure that any windows in the room are left
open during this process.
o It is advisable for you not to remain in the room whilst the
burning off process is taking place.
o You should leave the oven on maximum setting for 30 – 40
minutes.
Switching the gas oven on
The oven has electric ignition, to light it you should do the following:o Open the oven door.
o Push the main oven control knob down slightly and then turn it
anticlockwise to the word Max.
o Whilst it is pointed to the word Max., fully push down the control
knob and hold it down.
o The gas oven should light within 15 seconds.
o Once the burner has lit, continue to keep the control knob held
down for a further 10 seconds. Otherwise the safety cut off will
operate and block the flow of gas.
o IMPORTANT: When you are certain that the oven burner is fully
lit, close the oven door. Turn the control knob clockwise until it
reaches the temperature that you desire.
o DO NOT turn the control knob past the 130°C position,
otherwise the burner may go out.
o If the gas oven does not light within 15 seconds, then release
the control knob. IMPORTANT: YOU MUST TURN THE
CONTROL KNOB BACK TO ITS ORIGINAL POSITION;
OTHERWISE GAS WILL CONTINUE TO BE RELEASED.
12
o Wait for 1 minute, before repeating the ignition procedure again.
When lighting the oven for the first time, it may take
several times until the electric ignition operates. This is
due to there being air in the gas pipe.
Switching the gas grill on
The grill has electric ignition, to light the grill you should do the
following:o Open the door of the oven and fit the grill deflector to the
front of the appliance.
o Push the main oven control knob down slightly and
then turn it anticlockwise to the grill symbol (shown
opposite)
o Whilst it is pointed to the grill symbol, fully push down this
control knob and hold it down.
o The gas grill should light within 15 seconds.
o Once the burner has lit, continue to keep the control knob held
down for a further 10 seconds. Otherwise the safety cut off will
operate and block the flow of gas.
o THE OVEN DOOR MUST BE LEFT OPEN WHILST YOU ARE
GRILLING AND THE GRILL DEFLECTOR SHOULD ALWAYS
BE FITTED.
o If the gas grill does not light within 15 seconds, then release the
control knob. IMPORTANT: YOU MUST TURN THE CONTROL
KNOB BACK TO ITS ORIGINAL POSITION; OTHERWISE
GAS WILL CONTINUE TO BE RELEASED.
o Wait for 1 minute, before repeating the ignition procedure again.
When lighting the grill for the first time, it may take
several times until the electric ignition operates. This is
due to there being air in the gas pipe.
13
o IMPORTANT: You should allow the oven to cool completely
before attempting to remove the grill deflector. If you
attempt to remove the grill deflector before the oven is
cool, the deflector will be hot.
Using and assembling the rotisserie
o Place the food on the spit (L); making sure that it is placed
centrally between the two forks (F). Otherwise excess strain will
be placed on the motor (R).
o Place one end of the spit (L) onto support (G) and put the
opposite end into the hole of the motor (P).
o Fill the drip tray with a little water and place this under the spit
(L).
o Fit the grill deflector (S) into position and leave the door half
way open.
o Light the gas grill (as described previously) and
then press the rotisserie on/off button (pictured
opposite).
14
o To rotate the spit in the opposite direction, whilst wearing a
protective oven glove, turn the rotation knob (A).
o Make sure that you press the rotisserie on/off button, and then
turn the main oven control knob to 0 before attempting to
remove the spit (L).
Using the minute minder
The minute minder can be used independently of
the oven or grill for a time period of up to 60
minutes.
o To set the timer, turn the knob fully clockwise until it stops and
then turn it back anticlockwise to the required time.
o The time period that has been set will expire when the control
knob reaches zero, a brief audible signal will sound.
IMPORTANT: If you have the oven or grill in use
whilst the timer is counting down. When the
countdown ends, the oven will continue to heat. You
must turn off the oven/grill using the relevant
control knob.
The oven light
o The oven light button (pictured opposite), switches the
light bulb on and off. Press this button down to switch
the light on, then press the same button again to
switch the light off.
o The oven light can be switched on, regardless of whether the
oven/grill is in use.
15
Cooking guidelines
o Please refer to the information given on food packaging for
guidance on cooking temperatures and times. Once familiar with
the performance of your appliance, temperatures and times can
be varied to suit personal preference.
o Preheat the oven for at least 15 minutes before placing food into
the cavity.
o Make sure that frozen foods are thoroughly thawed before
cooking, unless the instructions on the food packaging advise
that you can “cook from frozen”.
o Before cooking, check that any unused accessories are removed
from the oven.
o Place cooking trays in the centre of the oven and leave gaps
between the trays to allow air to circulate.
o Try to open the door as little as possible to view the dishes.
Warnings
o Keep the oven door open when using the grill function and make
sure that the grill deflector is fitted.
o Do not use aluminium foil to cover the grill pan or heat items
wrapped in aluminium foil under the grill. The high reflectivity of
the foil could potentially damage the grill element.
o You should also never line the base of your oven with aluminium
foil.
o During cooking, never place pans or cookware directly onto the
bottom of your oven. They should always be placed on the shelf
provided.
o The grill becomes extremely hot during operation, avoid touching
it inadvertently when handling the food which you are grilling.
o Important: Be careful when opening the door, to avoid contact
with hot parts and steam.
16
Using the hob top
The following symbols will appear on the control panel, next to each
control knob:
Black circle: gas off
Large flame: maximum setting
Small flame: minimum setting
o The minimum setting is at the end of the anti-clockwise rotation
of the control knob.
o All operation positions must be selected between the maximum
and minimum positions.
o Never select a knob position between the maximum and off
position.
Automatic electric ignition with flame failure safety device
To ignite a burner:
o Press in the control knob of the burner that you wish to light and
turn it clockwise to the maximum position.
o If you keep the control knob depressed, the automatic ignition
for the burner will operate.
o IMPORTANT: Once the burner has lit, continue to keep the
control knob held down for a further 10 seconds. Otherwise the
safety cut off will operate and block the flow of gas.
o In case of power failure, the burners can be lit by carefully using
a match.
17
Energy saving tips
o The diametre of the bottom of the pan should correspond to that
of the burner.
o The burner flame must never extend beyond the diametre of the
pan.
o Use flat bottomed pans only
o When possible, keep a lid on the pan whilst cooking.
o Cook vegetables with as little water as possible, to reduce
cooking times.
o IMPORTANT: Always place pans centrally over the hob burners
and position them so that the handles cannot get accidentally
caught or knocked off. You should also make sure that the
handle is not over one of the other hob burner flames.
18
Cleaning and maintenance
Cleaning operations must only be carried out
when the oven is cool.
The appliance should be disconnected from your
mains supply before commencing any cleaning
process.
o The oven should be thoroughly cleaned before it is operated for
the first time and after each use. This will avoid residual food
stuffs becoming baked on the oven cavity. After residues have
been baked on several times, they are far more difficult to
remove.
o Never clean the oven surfaces by steam cleaning.
o The oven cavity should only be cleaned with warm soapy water,
using either a sponge or soft cloth. No abrasive cleaners should
be used.
o Any stains that may appear on the bottom of the oven will have
originated from food splashes or spilt food, these splashes occur
during the cooking process. These could possibly be a result of
the food being cooked at an excessively high temperature or
being placed in cookware that is too small.
o You should select a cooking temperature that is appropriate for
the food that you are cooking. You should also ensure that the
food is placed in an adequately sized dish and that you use the
drip tray where appropriate.
o Outer parts of the oven should only be cleaned with warm soapy
water, using either a sponge or soft cloth. No abrasive cleaners
should be used.
o If you use any form of oven cleaner on your appliance, then you
must check with the manufacturer of the cleaner that it is
suitable for use on your appliance.
o Any damage that is caused to the appliance by a cleaning
product will not be fixed by Baumatic free of charge, even
if the appliance is within the guarantee period.
19
Cleaning the hob burners
The hob burners should be cleaned once a week or more frequently if
they get soiled.
o Remove the hob burners by pulling them upwards and away
from the hob top.
o Soak them for about ten minutes in hot water and a little
detergent.
o After cleaning and washing them, wipe and dry them carefully.
o Before placing the burners back on the hob top, make sure that
the gas jet is not blocked.
o IMPORTANT: Make sure that you reassemble the burners in the
original way.
Replacing the oven bulb
IMPORTANT: The oven must be disconnected from
your mains supply before you attempt to either
remove or replace the oven bulb.
o Remove all oven shelves
and the drip tray.
o Unscrew the lamp cover.
o Unscrew the bulb and
remove it from its holder.
o Replace the bulb with a 15 W/300°C, screw type pigmy.
o Do not use any other type of bulb.
o Screw the lamp cover back into its original position.
20
Removing the oven door for cleaning
o Open the oven door fully.
o The hinges (A) are provided with two movable hooks (B).
o Rotate the hooks into the slot (C).
o You should grip the sides of the door at the centre and then
incline it slightly towards the oven cavity and then by pulling it
gently away from the oven cavity.
o IMPORTANT: You should make sure that the door is supported
at all times and that you place the door on some padded
material whilst cleaning it.
o The oven door and door glass should only be cleaned using a
damp cloth and a small amount of detergent. The cloth MUST
NOT have come into contact with any form of cleaning product
or chemical previously.
o Replace the oven door by introducing the hinges back into their
relevant slots. Before closing the doors DO NOT FORGET TO
RESET THE MOVABLE HOOKS.
o DO NOT attempt to move the hooks whilst the door is not
attached to the oven, as the hinges are under high spring
tension and injury may result.
21
Installation
The installation must be carried out by a suitably
qualified person, in accordance with the current
version of the following.
o UK Regulations and Safety Standards or their European
Norm Replacements.
o Building Regulations (issued by the Department of the
Environment).
o Building Standards (issued by the Scottish Development
Department).
o IEE Wiring Regulations.
o Electricity At Work Regulations.
o Gas
Safety
(Installation
and
Use)
(Amendment)
Regulations.
Positioning
The adjacent furniture and all materials used in the
installation must be able to withstand a minimum
temperature
of
85°C
above
the
ambient
temperature of the room it is located in, whilst the
appliance is in use.
o Your appliance is heavy, so you should be careful when moving
or positioning it.
o Do not try to move the cooker by pulling on either the door,
handle or control panel.
o The oven may be located in a kitchen, or a bedroom, but not in a
room containing a bath or shower. The oven must not be
installed in a bedroom of less than 20m³ in size.
o LPG models must not be installed in a room or internal space
below ground level (e.g. in a basement).
22
o The cooker is designed to slot in between 600 mm deep
cabinets, which are spaced approximately 940 mm apart.
o It can also be used as freestanding, with a cabinet to one side, in
a corner setting or with its back to a wall.
o IMPORTANT: It should not be installed at the end of a run of
cabinets, if there is a cabinet at immediate right angles to the
cooker door.
o The wall behind the cooker and 450 mm above and across the
width of the cooker should be an incombustible material and
preferably an easy clean surface, such as ceramic tiles.
o Any overhanging surface or cooker hood should be at least 700
mm above the highest point on the hob top (including the
burners).
o Baumatic do not recommend that the cooker is positioned below
wall cupboards, as the heat and steam from the appliance and
what is being cooked, may damage the cupboard and its
contents.
23
o The cooker is fitted with four legs that can be adjusted to match
the height of your kitchen cabinets.
o To assemble them it is necessary to raise the cooker and to
screw the four legs into position, on each corner of the base of
the appliance.
o IMPORTANT: They must be screwed clockwise into position and
not just slotted into the holes on each corner. You must screw
them through the brackets that are also provided.
Gas connection
This appliance must be installed by a competent
person in accordance with the current versions of
the following UK (United Kingdom) or ROI (Republic
of Ireland) Regulations and Safety Standards or
their European Norm Replacements.
Important information
o This cooker is supplied to run on natural gas only and cannot
be used on any other type of gas without modification.
o Conversion for use on LPG and other gases must only be
undertaken by a qualified person. For information on the use of
other gases, please contact the Baumatic Technical Department.
o The cooker must be installed by a qualified person, in
accordance with the current edition of the Gas Safety
(Installation and Use) (Amendment) Regulations and the
relevant building/I.E.E. Regulations.
o Failure to install the appliance correctly could invalidate
Baumatic’s guarantee and lead to prosecution under the
regulations quoted above.
24
o In the UK, GASSAFE registered installers are authorised to
undertake the installation and service work, in compliance with
the above regulations.
Ventilation requirements
o The room containing the cooker should have an air supply in
accordance with the current edition of BS 5440: Part 2:
o The room must have opening windows or equivalent; some
rooms may also require a permanent vent.
o If the room has a volume between 5 and 10m³, it will require an
air vent of 50cm² (effective area). Unless it has a door which
opens directly to the outside.
o If the room has a volume of less than 5m³, it will require an air
vent of 100cm² (effective area).
o If there are any other fuel burning appliances in the same room
the current edition of BS 5440: Part 2: should be consulted to
determine air vent requirements.
o Ensure that the room containing the cooker is well ventilated,
keep natural ventilation holes or install a mechanical ventilation
device (mechanical cooker hood).
o Prolonged intensive use of the appliance may call for additional
ventilation, either by the opening of a window, or by increasing
the level of the mechanical ventilation device (where present).
o This cooker is not fitted with a device for discharging the
products of combustion. Ensure that the ventilation rules and
regulations are followed.
o Excess steam from the oven, vents out at the top back edge of
the cooker, so make sure that the walls behind and near the
cooker are resistant to heat, steam and condensation.
o Your cooker must stand on a flat surface so that when it is in
position the hob is level. When in position check that the cooker
is level by using a spirit level and adjust the 2 feet at the rear
and the 2 feet at the front if necessary.
o Remember that the quantity of air necessary for combustion
must never be less than 2m³/h for each kW of power (see total
power in kW on the appliance rating plate).
25
Gas Safety (Installation and Use) Regulations
o It is the law that all gas appliances are installed by competent
persons in accordance with the current edition of the Gas Safety
Installation and Use Regulations.
o It is in your interest and that of safety to ensure compliance with
the law.
o In the UK, GASSAFE registered installers work to safe standards
of practice. The cooker must also be installed in accordance with
the current edition of BS 6172. Failure to install the cooker
correctly could invalidate the warranty, liability claims and lead
to prosecution.
o IMPORTANT: It is a requirement for a stability chain to be
fitted to the appliance. Please see page 32 for more
detailed information on this.
Gas connection
ALL INSTALLATION AND SERVICE WORK MUST BE
CARRIED
OUT
BY
A
GASSAFE
REGISTERED
ENGINEER.
o Prior to installation, ensure that the gas supply conditions
(nature of the gas and gas pressure) and the adjustment
conditions are compatible. The adjustment conditions for this
appliance are stated on the rating plate which can be found on
the back cover.
o This appliance is not designed to be connected to a combustion
product evacuation device. Particular attention should be given
to the relevant requirements regarding ventilation.
o In
compliance
with
the
manufacturer’s
installation
instructions, the adaptor elbow
should be connected to the gas
inlet at the rear of the appliance
and pointing in a downward
direction. As indicated in the
diagram opposite.
26
o IMPORTANT: THE FIBRE WASHERS SHOWN IN THE ABOVE
DIAGRAM MUST BE IN PLACE WHEN CONNECTING THE
ADAPTOR ELBOW.
o Connection to the cooker should be made with an approved
appliance flexible connection to BS 669.
o If the cooker has been converted for use with LPG, then it should
be connected to the gas supply using an appropriate bayonet
type hose. The hose MUST be suitable for use with LPG gas,
these are identifiable by a red band or stripe.
o A hose length of 0.9m to 1.25m is recommended. The length of
hose chosen should be such that when the cooker is in situ, the
hose does not touch the floor.
o Care should be taken to ensure that the temperature rise of
areas at the rear of the cooker that are likely to come in contact
with the flexible hose do not exceed 70°C.
o Gas pressure may be checked on a semi-rapid hob burner.
Remove the appropriate injector and attach a test nipple. Light
the other burners and observe that the gas pressure complies
with the gas standards in force.
o This cooker can be connected to the supply both on the right and
left hand side at the rear of the cooker. To reverse the position,
remove the blanking plug and refit it to the opposite side to
where the hose is being connected.
27
Gas adjustment (Conversion to LPG for the hob top)
All work must be
registered engineer.
carried
out
by
a
GASSAFE
IMPORTANT: Always isolate the cooker from the electricity
supply before changing the injectors and/or adjusting the
minimum flow of the burners.
o Remove the pan-stands, burners and flame
spreaders (A).
o Unscrew the injector (B) and replace it with
the stipulated injector for the new gas supply
(see table below).
Burner
Type
Auxiliary
burner
(Ø55mm)
Gas Type
Liquid
gas
Natural
gas
Semi-rapid Liquid
burner
gas
(Ø75mm)
Natural
gas
Rapid
Liquid
burner
gas
(Ø100mm) Natural
gas
Wok
LPG
burner
(Ø130mm) Natural
gas
G30/
G31
G20
Pressure Injector Gas
(mbar)
Marking Consumption*
(1/100
mm)
28…
52
73 g/h
30/37
20
72
95 dm³/h
G30/
G31
G20
28…
30/37
20
68
98
167 dm³/h
G30/
G31
G20
28…
30/37
20
88
218 g/h
116
286 dm³/h
G30/G31 28…
30/37
G20
20
96
262 g/h
135
343 dm³/h
MAX
MIN
Power Power
(kW)
(kW)
1.000
0.300
1.750
0.440
3.000
0.750
3.600
1.500
127 g/h
28
* In reference conditions,
pressure 1013.25 mbar
gas
temperature
15°C,
atmospheric
o Reassemble all the burners carefully; in particular you should
make sure that the flame spreader is correctly placed on the
burner.
o IMPORTANT: After changing the injectors YOU MUST
follow the minimum flow adjustment section below.
Minimum flow adjustment for hob gas taps.
All work must be
registered engineer.
carried
out
by
a
GASSAFE
o Light the burner and set the knob
at the minimum position.
o Remove the knob from the tap and
place a small bladed screwdriver in
the centre of the tap shaft.
o Unscrew the adjusting screw, in order to increase the gas flow
or tighten the adjusting screw to decrease the gas flow.
o The correct adjustment is obtained when the flame has a
length of about 3 – 4 mm.
o For butane/propane gas, the adjusting screw must be tightly
screwed in.
o Refit the control knob.
o Make sure that the flame does not go out by quickly turning
from maximum flow to minimum flow. If it does then remove
the control knob and make further adjustments to the gas
flow, testing it again once the adjustment has been made.
o IMPORTANT: On completion carry out a gas tightness
test.
29
Gas adjustment (Conversion to LPG for the oven and grill)
All work must be
registered engineer.
carried
out
by
a
GASSAFE
IMPORTANT: Always isolate the cooker from the electricity
supply before changing the injectors and/or adjusting the
minimum flow of the burners.
o Free the burners from their
fixing screws.
o Unscrew the injectors and replace
them with the stipulated injector
for the new gas supply (see table
below).
Burner Gas Type
Type
Gas
MAX
MIN
consumption* Power Power
(kW)
(kW)
Main
Oven
305 g/h
Grill
Oven
Pressure Injector
Marking
(1/100
mm)
LPG
G30/ 28…
98
G31 30/37
Natural G20 20
150
gas
LPG
G30/ 28…
88
G31 30/37
Natural G20 20
136
gas
* In reference conditions,
pressure 1013.25 mbar
gas
4.200
1.000
3.300
N/A
400 dm³/h
240 g/h
314 dm³/h
temperature
15°C,
atmospheric
IMPORTANT: You must change the oven and grill injectors.
30
IMPORTANT: After changing the injectors YOU MUST follow the
minimum flow adjustment section below.
Minimum flow adjustment for the oven and grill burners
All work must be
registered engineer.
carried
out
by
a
GASSAFE
o Light the burner and set the knob
at the minimum position.
o Remove the knob from the tap and
place a small bladed screwdriver
into the screw that’s to the side of
the gas tap.
o Unscrew the adjusting screw, in order to increase the gas flow
or tighten the adjusting screw to decrease the gas flow.
o The correct adjustment is obtained when the flame has a
length of about 3 – 4 mm.
o For butane/propane gas, the adjusting screw must be tightly
screwed in.
o Refit the control knob.
o Make sure that the flame does not go out by quickly turning
from maximum flow to minimum flow. If it does then remove
the control knob and make further adjustments to the gas
flow, testing it again once the adjustment has been made.
o IMPORTANT: On completion carry out a gas tightness
test.
31
Fitting a stability chain
IMPORTANT: It is a legal requirement for your
GASSAFE registered installer to fit a stability chain.
The stability hook should be securely fixed to the fabric of the building,
in an adjacent position to the safety chain at the rear of the appliance.
The chain should be kept as short as is practical.
32
Electrical connection
This appliance must be installed by a qualified
person in accordance with the latest edition of the
I.E.E. Regulations and in compliance with Baumatic’s
instructions.
WARNING: THIS APPLIANCE MUST BE EARTHED.
o Before connecting the appliance, make sure that the supply
voltage marked on the rating plate corresponds with your mains
supply voltage.
o This appliance should be wired into a 13 A double pole switched
fused spur outlet, having 3 mm contact separation and the fuse
rating reduced to 3 amps. This should be placed in an easily
accessible position adjacent to the appliance, preferably above
worktop level. An outlet can then be located at the rear of the
appliance for connection.
o Care must be taken to ensure that the temperature of the mains
supply cable does not exceed 50°C.
o If the mains supply cable is damaged, then it must be replaced
by an appropriate replacement.
o Cable type: H05 RRF 3 core x 0.75 mm³
33
Connecting the mains supply cable
IMPORTANT
The wires in the mains lead are
coloured in accordance with the
following code:
GREEN AND YELLOW
BLUE
BROWN
EARTH
NEUTRAL
LIVE
o Open the mains terminal block cover as shown, unscrew the
cable clamp (A) and unscrew (not fully) the screws in the mains
terminal block (L, N, E) which secure the three wires of the
mains cable.
o Fit the cable and refit the cable clamp (A).
o Allow sufficient cable length for the cooker to be pulled out for
cleaning, but do not let it hang closer than 50mm to the floor.
o The cable can be looped if necessary, but make sure that is not
kinked or trapped when the cooker is in position.
Replacing the mains supply cable
If the mains supply cable is damaged, then it must be replaced by an
appropriate replacement.
The mains supply cable should be replaced in accordance with the
following instructions:
o Switch the appliance off at the socket.
o Open the box of the supply board.
o Unscrew the clamp (A) fixing the cable.
o Replace the cable with one of the same length and in accordance
with the specification given above.
o The “green-yellow” earth wire must be connected to the terminal
. It must be about 10 mm longer than the live and
marked
neutral wires.
34
o The “blue” neutral wire must be connected to the terminal
marked with letter (N) - the live wire must be connected to the
terminal marked with letter (L).
My appliance isn’t working correctly
The gas oven burner or grill burner do not light.
* Check that the oven is switched on at your mains supply.
* Check that the fuse in the spur outlet doesn’t need replacing.
* Check that there is not a problem with your gas supply
Food is cooking too quickly or too slowly.
* Check that you are cooking at an appropriate temperature and
shelf level.
The oven is not cooking evenly.
* Check that the oven is installed correctly.
* Check that you are cooking at an appropriate temperature and
shelf level.
The oven light is not working.
* Refer to page 20 and follow the “Replacing the oven bulb”
section.
I am getting condensation in my oven.
* Steam and condensation is a natural by product of cooking any
food with high water content, such as frozen food, chicken etc.
* You may get condensation in the oven cavity and forming
between the oven door glasses. This is not necessarily a sign
that the oven is not working correctly.
* Do not leave food in the oven to cool after it has been cooked
and the oven has been switched off.
* Use a covered container, where practical, when cooking to
reduce the amount of condensation that forms.
35
IMPORTANT: If your appliance appears not to be
operating correctly, then you should disconnect it
from your mains supply and then contact the
Customer Care Department on telephone number
(0118) 933 6911.
DO NOT ATTEMPT TO REPAIR THE APPLIANCE
YOURSELF.
Please note that if an engineer is asked to attend whilst the product is
under guarantee and finds that the problem is not the result of an
appliance fault, then you may be liable for the cost of the call out
charge.
The appliance must be accessible for the engineer to perform
any necessary repair. If your appliance is installed in such a
way that an engineer is concerned that damage will be caused
to the appliance or your kitchen, then he will not complete a
repair.
This includes situations where appliances have been tiled in,
sealed in with sealant, have wooden obstructions placed in
front of the appliance, like plinths. Or any installation other
than the one specified by Baumatic Ltd. has been completed.
Please refer to the conditions of guarantee that appear on the
warranty card that you receive with the appliance.
IMPORTANT: Baumatic Ltd. operates a policy of continuous
improvement and reserves the right to adjust and modify its
products without prior notification.
36
United Kingdom
Baumatic Ltd.,
Baumatic Buildings,
6 Bennet Road,
Reading, Berkshire
RG2 0QX
United Kingdom
Czech Republic
Baumatic CR spol s.r.o.
Průmyslová zóna Sever 696
460 11 Liberec 11
Czech Republic
Sales Telephone
(0118) 933 6900
Sales Fax
(0118) 931 0035
Customer Care Telephone
(0118) 933 6911
Customer Care Fax
(0118) 986 9124
Spares Telephone
(01235) 437244
Advice Line Telephone
(0118) 933 6933
www.baumatic.cz
E-mail:
[email protected]
[email protected]
[email protected]
[email protected]
Website:
www.baumatic.co.uk
Republic of Ireland
Service Telephone
1-890 812 724
Spares Telephone
091 756 771
+420 483 577 200
Slovakia
Baumatic Slovakia, s.r.o.
Galvániho 7/D
Slovakia
+421 255 640 618
Germany
Baumatic Gmbh
Lilienthalstrasse 1
320 52 Herford
Deutschland
+49 5221 694 99-0
www.baumatic.de
Italy
Baumatic Italia S.R.L.
Via Galvani N.3
35011 Campodarsego (PD)
+3904 9920 2297
www.baumatic.it
Holland
Baumatic Benelux B.V.
Grindzuigerstraat 22
1333 MS ALMERE
Nederland
+3136 549 1555
www.baumatic.nl
37
38
39
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement