Tyan | B5397T26W8H | Specifications | Tyan B5397T26W8H server barebone

Tyan B5397T26W8H server barebone
Tank TA26
B5397
Service Engineer’s Manual
PREFACE
Copyright
This publication, including all photographs, illustrations, and software, is protected under international copyright laws, with all rights
reserved. Neither this manual, nor any material contained herein,
may be reproduced without written consent of the manufacturer-.
Copyright 2007
Version 1.0
Disclaimer
Information contained in this document is furnished by TYAN Computer Corporation and has been reviewed for accuracy and reliability
prior to printing. TYAN assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of
TYAN products including liability or warranties relating to fitness for
a particular purpose or merchantability. TYAN retains the right to
make changes to product descriptions and/or specifications at any
time, without notice. In no event will TYAN be held liable for any
direct or indirect, incidental or consequential damage, loss of use,
loss of data or other malady resulting from errors or inaccuracies of
information contained in this document.
Trademark Recognition
All registered and unregistered trademarks and company names
contained in this manual are property of their respective owners
including, but not limited to the following.
TYAN, Tank TA26 B5397, and Tempest i5400PW are trademarks of
TYAN Computer Corporation.
Intel, Dual-Core Xeon 5100/5200 Series, Quad-Core 5300/5400
Series, and combinations thereof are trademarks of Intel Corporation.
Phoenix, PhoenixBIOS are trademarks of Phoenix Technologies.
Microsoft, Windows are trademarks of Microsoft Corporation.
SuSE, is a trademark of SuSE AG.
IBM, PC, AT, and PS/2 are trademarks of IBM Corporation.
Winbond is a trademark of Winbond Electronics Corporation.
Portable Document Format (PDF) is a trademark of Adobe Corporation.
i
Federal Communications Commission (FCC)
Notice for the USA Compliance Information Statement (Declaration of Conformity Procedure) DoC FCC
Part 15: This device complies with part 15 of the FCC
Rules
Operation is subject to the following conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received including interference that may cause undesired operation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and the
receiver.
– Plug the equipment into an outlet on a circuit different from
that of the receiver.
Consult the dealer on an experienced radio/television technician for
help.
Notice for Canada
This apparatus complies with the Class B limits for radio interference
as specified in the Canadian Department of Communications Radio
Interference Regulations. (Cet appareil est conforme aux norms de
Classe B d’interference radio tel que specifie par le Ministere Canadien des Communications dans les reglements d’ineteference
radio.)
Notice for Europe (CE Mark) This product is in conformity
with the Council Directive 89/336/EEC, 92/31/EEC
(EMC).
CAUTION: Lithium battery included with this board. Do not puncture,
mutilate, or dispose of battery in fire. Danger of explosion if battery
is incorrectly replaced. Replace only with the same or equivalent
type recommended by manufacturer. Dispose of used battery
according to manufacturer instructions and in accordance with your
local regulations.
ii
About this Manual
This manual provides you with instructions on installing your Tank
TA26 B5397. This manual is intended for experienced users and
integrators with hardware knowledge of personal computers.
This manual consists of the following parts:
Chapter 1:
Provides an Introduction to the TA26 B5397 barebone, packing list, describes the external components, gives a table of key components, and
provides block diagrams of the system.
Chapter 2:
Covers procedures on installing the CPU, memory modules, PCI-E card, hard drives, and floppy
drive.
Chapter 3:
Covers removal and replacement procedures for
pre-installed components
Appendix:
Provides instructions on installing the SO-DIMM
card. Describes the differences between mainboard BIOS and system BIOS. The cable connection and FRU parts tables are also provided.
For information on the mainboard, please refer to the attached mainboard user’s manual. You can find the detailed description about
jumper and BIOS settings from the motherboard manual.
iii
SAFETY INFORMATION
Before installing and using the TA26 B5397, take note of the following precautions:
iv
–
–
–
Read all instructions carefully.
–
Only use the power source indicated on the marking label. If
you are not sure, contact the Power Company.
–
The unit uses a three-wire ground cable, which is equipped
with a third pin to ground the unit and prevent electric shock.
Do not defeat the purpose of this pin. If your outlet does not
support this kind of plug, contact your electrician to replace
your obsolete outlet.
–
Do not place anything on the power cord. Place the power
cord where it will not be in the way of foot traffic.
–
Follow all warnings and cautions in this manual and on the
unit case.
–
Do not push objects in the ventilation slots as they may touch
high voltage components and result in shock and damage to
the components.
–
When replacing parts, ensure that you use parts specified by
the manufacturer.
–
When service or repairs have been done, perform routine
safety checks to verify that the system is operating correctly.
–
Avoid using the system near water, in direct sunlight, or near
a heating device.
–
Cover the unit when not in use.
Do not place the unit on an unstable surface, cart, or stand.
Do not block the slots and opening on the unit, which are provided for ventilation.
Table of Contents
Chapter 1: Overview
1.1
1.2
1.3
1.4
1.5
About the TYAN Tank TA26 B5397 . . . . . . . . . . . . . . . . . . . . . . . 1
Product Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4.1 Box Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.4.2 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
About the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.5.1 System Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.5.2 System Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.5.3 LED Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.5.4 Motherboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.5.5 Jumpers & Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.5.6 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.5.7 Internal View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 2: Setting Up
2.1
2.2
2.0.1 Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.0.2 Work Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.0.3 Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.0.4 Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installing Motherboard Components. . . . . . . . . . . . . . . . . . . . . . . 15
2.1.1 Removing the Chassis Cover. . . . . . . . . . . . . . . . . . . . . . . 15
2.1.2 Installing the CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.1.3 Installing the Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.1.4 Installing Low Profile PCI-E Cards. . . . . . . . . . . . . . . . . . 23
2.1.5 Installing Hard Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2.1.6 Installing a Floppy Drive . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.2.1 Installing the Server in a Rack. . . . . . . . . . . . . . . . . . . . . . 29
Chapter 3: Replacing Pre-Installed Components
3.1
3.2
3.3
3.4
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.1.1 Work Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.1.2 Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3.1.3 Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Disassembly Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Removing the Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Replacing Motherboard Components . . . . . . . . . . . . . . . . . . . . . . 40
3.4.1 Disconnecting All Motherboard Cables . . . . . . . . . . . . . . 40
v
3.5
3.6
3.7
3.8
3.9
3.4.2 Removing the Motherboard . . . . . . . . . . . . . . . . . . . . . . . . 41
3.4.3 Removing the CPU Heatsink Mounting Plates . . . . . . . . . . 42
Replacing the Slim DVD-ROM . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Replacing the LED Control Board . . . . . . . . . . . . . . . . . . . . . . . . 45
3.6.1 LED Control Board Features . . . . . . . . . . . . . . . . . . . . . . . 47
3.6.2 LED Control Board Connector Pin Definitions. . . . . . . . . 47
Replacing the Backplane. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
3.7.1 M1220 SAS/SATA Backplane Features. . . . . . . . . . . . . . . 50
3.7.2 M1220 SAS/SATA Backplane Connector Pin Definitions . 52
Replacing the System Fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Replacing the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
3.9.1 Standard Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
3.9.2 Optional 1+1 Redundant Power Supply . . . . . . . . . . . . . . 59
Appendix I: BIOS Differences
Appendix II: Cable Connection Tables
Appendix III: Installing the SO-DIMM Card
Appendix IV: FRU Parts Table
vi
Chapter 1: Overview
1.1
About the TYAN Tank TA26 B5397
Congratulations on your purchase of the TYAN Tank TA26
B5397, a highly-optimized rack-mountable barebone system.
The Tank TA26 B5397 is designed to support two Intel DualCore Xeon 5100/5200 Series, Quad-Core Xeon 5300/5400
Series processors, providing a rich feature set and incredible
performance. Leveraging advanced technology from Intel,
the Tank TA26 B5397 server system is capable of offering
scalable 32 and 64-bit computing and high-bandwidth memory design. The Tank TA26 B5397 not only empowers your
company in today’s demanding IT environment but also offers
a smooth path for future application usage.B5397
TYAN is also proud to deliver the Tank TA26 B5397 in SAS
flavor while supporting up to eight (8) hot-swap hard drives
and one (1) slim DVD-ROM drive. The Tank TA26 B5397
uses TYAN’s latest tooling-made chassis featuring a robust
structure, tool-less and modularized design, and a solid
mechanical enclosure. All of this provides the Tank TA26
B5397 the power and flexibility to meet the needs of nearly
any server application.
1.2
Product Models
Model
HDD Bays
Backplane
Power Supply
B5397T26W8H
8
8-port
SAS/SATA
Single 700W
B5397T26W8HR
8
8-port
SAS/SATA
700W 1+1
redundant
Chapter 1: Overview
1
1.3
Features
• Auto-configuration of hard disk
types
• Industry 2U rack-mountable chassis
• Multiple boot options
• Storage bay:
• 48-bit LBA support
– (8) 3.5” HDD bays
Expansion Slots
– (1) slim line ODD bay
• Dimensions:
• Two (2) PCI-E x16 slot (w/ x16 PCI– D 26 x W 16.7 x H 3.4 inch
E Gen2 signals from MCH)
– D 660 x W423 x H 87 mm
• One (1) PCI-E x8 slot (w/ x4
signals)
Motherboard
• Two (2) PCI-X 133/100MHz slots
• TYAN Tempest i5400PW S5397
• One (1) PCI 32/33MHz slot
• SSI/ Extended ATX (12” x 13”)
• Supports total six (6) low-profile
Processors
expansion cards
• Dual LGA771 sockets
Back I/O Ports
• Supports one or two Dual-Core
• One stacked keyboard & one PS/2
Intel® Xeon® 5100/5200 Series,
mouse ports
• Two (2) stacked USB 2.0 ports
Quad-Core Intel® Xeon®
• One (1) 15-pin VGA port
5300/5400 Series processors
• One (1) 9-pin serial port
• 1066/1333/1600MT/s system bus
• Two (2) stacked RJ-45 x 2 LAN +
• VRD 11.0
one RJ-45
Enclosure
Chipset
• Intel® i5400B MCH chipset
• Intel® 6321ESB I/O Controller Hub
• Winbond 83627HF Super I/O chip
Memory
• Total sixteen (16) 240-pin DDR2
FBDIMM sockets
• Supports up to 64GB DDR2533/667/800 FBD memory
Video
• XGI Z9S, PCI interface
• 32MB DDR2 memory
BIOS
• Phoenix BIOS® on 8Mbit Flash
ROM
• Supports ACPI 1.0b
• Serial Console Redirect
• PXE via Ethernet, USB device boot
• PnP, DMI 2.0, WfM 2.0 Power
Management
• User-configuration of H/W
monitoring
2
Front Panel Features
• I/O
– (2) USB 2.0 ports
• LED indicators
– Power LED
– (2) LAN LEDs
– HDD Active LED
– ID LED
• Switches
– Power
– Reset
– ID
Storage Controller
• SATA Controller
– Four (4) SATA 2.0 ports from
Intel ESB6321
– RAID 0, 1, 5, 10 supported
(Windows only)
• SAS Controller
– LSI® 1068E SAS controller with
PCI-E x8 interface
– Two (2) mini SAS (4 in 1)
connectors
– RAID 0, 1, 1E supported
Chapter 1: Overview
Server Management
• Automatic fan speed control
• Chassis intrusion alert
• Supports TYAN Server
Management (TSM)
• Optional TYAN SMDC M32952/M3296, IPMI v2.0 compliant
remote server management kit
(Note: SMDC support will be available
from S5397 R03 (PCB Rev. MOA) and
beyond version. )
Storage Backplane
• One (1) 8-port SAS backplane,
supporting up to 8 SAS HDDs or
SATA HDDs
Networking
•
•
•
•
One (1) Intel Gilgal (82563EB) PHY
Direct link to ESB6321
Two gigabit LAN ports
Two front panel LED pin headers
Power Supply
• EPS 12V, 2U, 700W high efficiency
power supply (80+) with PFC for
B5397T26W8H
• EPS 12V, 2U, 700W 1+1 redundant
power supply (80+) with PFC for
B5397T26W8HR
Regulatory
• FCC Class B (Declaration of
Conformity)
• CE (Declaration of Conformity)
Environment Temperature
• Operating temperature 5oC~35oC
• Non-operating temperature -40oC~
70oC
Chapter 1: Overview
3
1.4
Unpacking
This section describes the TA26 B5397 package contents
and accessories. Open the box carefully and ensure that all
components are present and undamaged.
1.4.1 Box Contents
Component
Description
Industry standard 2U chassis, (8) hot-swap
HDD bays
TYAN Tempest i5400PW S5397 motherboard
(pre-installed)
Slim DVD-ROM drive (pre-installed)
LED and USB control board (pre-installed)
EPS 12V, 2U, 700W PSU with PFC
(pre-installed) (A)
EPS 12V, 2U 700W 1+1 Redundant PSU with
PFC (pre-installed) (B)
B
A
System Fans:
1 x (60mm x 60mm) (A)
2 x (80mm x 80mm) (B)
A
4
B
Chapter 1: Overview
1.4.2 Accessories
If any items are missing or appear damaged, contact your
retailer or browse to TYAN’s Web site for service:
http://www.tyan.com.
The Web site also provides information on other TYAN products, plus FAQs, compatibility lists, BIOS settings, and more.
1 x TYAN Driver CD
CPU Heatsink
Power Cables
Left to right: Europe, US
Unit Handles
FDD Cable
Chapter 1: Overview
Barebone Manual &
Mainboard Manual
5
FDD Rails
Screw Pack
FDD Power Cable
Sliding Rail
6
TYAN Logo
Chapter 1: Overview
1.5
About the Product
The following views show you the product.
1.5.1 System Front View
Reset switch
ID switch
Power LED
Power switch
Warning LED
USB ports
HDD activity LED
LAN LEDs
ID LED
HDD Tray
Power LEDs
DVD-ROM drive
Hard Drive Bay x 8
HDD Tray
Activity LEDs
1.5.2 System Rear View
Power Supply Fan
Power Supply
Socket
2 USB Ports
Low Profile
PCI-E Slots
ID LED
Power Supply LED
PS/2 Mouse and
Keyboard Ports
LAN Port (IPMI)
Serial VGA
Port
Port
LAN1 (top)
LAN2 (bottom)
Note: The above shows a single power supply setup (B5397T26W8H). A redundant
power supply setup (B5397T26W6HR) is also available. In both cases, the output voltage is the same.
Chapter 1: Overview
7
1.5.3 LED Definitions
Front Panel
LED
Color
State
Description
Power
Green
OFF
ON
OFF
Power ON
Power OFF
HDD Activity
Amber
Blinking
OFF
OFF
HDD/DVD-ROM
access activity
No disk activity
LAN1/LAN2/Linkage
Green
Green
OFF
ON
Blinking
OFF
LAN linked
LAN accessing
No LAN linked
Fail
Red
ON
OFF
OFF
System fails
Abnormal power off
Normal
Green
OFF
ON
OFF
Power connected
Power disconnected
SAS
HDD
Green
Green
OFF
ON
Blinking
OFF
HDD ready
HDD access activity
HDD not ready
SATA
HDD
Green
OFF
Blinking
OFF
HDD access activity
No disk activity
Hot Swappable HDD
Tray Power LED
Hot Swappable
HDD Tray Active LED
Rear I/O LED
8
*Right or Left is viewed from the rear.
LED
Color
State
Description
LAN Linkage/ Activity
(Left Side)
Green
Green
OFF
ON
Blinking
OFF
LAN linked
LAN accessing
No LAN linked
LAN Mode
(Right Side)
Yellow
Green
OFF
ON
ON
OFF
1000Mb mode
100Mb mode
10Mb mode or No LAN linked
ID LED
Blue
OFF
ON
OFF
System is identified
System is not identified
Zippy Power
Supply LED
Green
Green
Amber
ON
1Hz Blinking
ON
Amber
1Hz Blinking
OFF
OFF
Output ON and OK
AC present/Only 5Vsb ON
Power supply critical event causing a
shutdown: failure, OCP, OVP, fan fail
Power supply warning event where
the power supply continues to operate: high temp., high power, high current, slow fan
No AC power
Chapter 1: Overview
1.5.4 Motherboard Layout
Chapter 1: Overview
9
1.5.5 Jumpers & Connectors
Jumper/Connector
Function
J7/J12/J19/J21/
J36/J40
4-pin FAN connector
J3
Onboard HD Audio Header
J6
CD_IN Audio Header
J8
IPMB Header
J20
COM2 Header
J22/J23
1394 Header
J28
Front Panel Header
J33
TYAN Fan Speed Header for Barebone
J37
TYAN LAN LED Header for Barebone
J38
TYAN LCM Header for Barebone
J41
USB Front Panel Header
P1
Audio Jack Header
J2
Aux. Power Header for TYAN Riser Card
(M2061)
JP1
Clear CMOS Jumper
(Close 1-2) Default
(Close 2-3) Clear CMOS
JP3
Onboard VGA Disable Jumper
(Close 1-2) Default, enabled
(Close 2-3) Disabled
JP4
Onboard 1394 Jumper
(Close 1-2) Default, enabled
(Close 2-3) Disabled
JP5
PCI-X Speed Select Jumper
(Close 1-2) Default, 133MHz
(Close 2-3) 100MHz
JP6
Onboard SAS Disable Jumper
(Close 1-2) Default, enabled
(Close 2-3) Disabled
10
Chapter 1: Overview
1.5.6 System Block Diagram
Chapter 1: Overview
11
1.5.7 Internal View
1
11
2
10
3
4
9
FAN3
FAN2
FAN1
8
5
6
7
1.
2.
3.
4.
5.
6.
7.
12
Memory Slots
Power Connector
Power Supply
Fan Duct
SAS / SATA Backplane
LED Control Board Cable
Eight (8) SAS / SATA HDD
trays
8. DVD-ROM Cable
9. System Fans (Right to Left:
FAN1, FAN2, FAN3)
10. Low Profile PCI-E Slots
11. SO-DIMM TARO Card
Socket
Chapter 1: Overview
Chapter 2: Setting Up
2.0.1 Before You Begin
This chapter explains how to install the CPU, CPU heatsink,
memory modules, hard drives, and floppy drive. Instructions
on inserting a PCI-E card are also given.
Take note of the precautions mentioned in this section when
installing your system.
2.0.2 Work Area
Make sure you have a stable, clean working environment.
Dust and dirt can get into components and cause malfunctions. Use containers to keep small components separated.
Putting all small components in separate containers prevents
them from becoming lost. Adequate lighting and proper tools
can prevent you from accidentally damaging the internal
components.
2.0.3 Tools
The following procedures require only a few tools, including
the following:
•
•
A cross head (Phillips) screwdriver
A grounding strap or an anti-static pad
Most of the electrical and mechanical connections can be disconnected using your fingers. It is recommended that you do
not use needle-nosed pliers to remove connectors as these
can damage the soft metal or plastic parts of the connectors.
Chapter 2: Setting Up
13
2.0.4 Precautions
Components and electronic circuit boards can be damaged
by discharges of static electricity. Working on a system that is
connected to a power supply can be extremely dangerous.
Follow the guidelines below to avoid damage to the
Tank TA26 B5397 or injury to yourself.
•
Ground yourself properly before removing the top
cover of the system. Unplug the power from the
power supply and then touch a safely grounded
object to release static charge (i.e. power supply
case). If available, wear a grounded wrist strap. Alternatively, discharge any static electricity by touching
the bare metal chassis of the unit case, or the bare
metal body of any other grounded appliance.
•
Avoid touching motherboard components, IC chips,
connectors, memory modules, and leads.
•
The motherboard is pre-installed in the system.
When removing the motherboard, always place it on
a grounded anti-static surface until you are ready to
reinstall it.
•
Hold electronic circuit boards by the edges only. Do
not touch the components on the board unless it is
necessary to do so. Do not flex or stress circuit
boards.
•
Leave all components inside the static-proof packaging that they ship with until they are ready for installation.
•
After replacing optional devices, make sure all
screws, springs, or other small parts are in place and
are not left loose inside the case. Metallic parts or
metal flakes can cause electrical shorts.
Notes:
• All connectors are keyed to only attach one way.
• Always use the correct screw size as indicated in the
procedures.
14
Chapter 2: Setting Up
2.1
Installing Motherboard Components
This section describes how to install components on to the
motherboard, including CPU, memory modules and PCI-E
card.
2.1.1 Removing the Chassis Cover
Follow these instructions to remove the Tank TA26 B5397
chassis cover.
1. Turn the screw on the back side. Then slide the chassis
cover in the direction of arrow.
2. Lift off the cover.
Chapter 2: Setting Up
15
3. Unscrew the fan duct.
16
Chapter 2: Setting Up
2.1.2 Installing the CPU
Follow these instructions to install the CPU.
1. Remove the cover on the CPU socket.
2. Lift up the CPU lever to unlock the socket.
Chapter 2: Setting Up
17
3. Open the socket in the direction as illustrated.
4. Place the CPU in the CPU socket, ensuring that pin 1 is
located as shown below.
5. Close the cover and press the CPU socket lever down to
secure the CPU.
18
Chapter 2: Setting Up
6. Place theheatsink on top of the CPU and secure with four
screws as shown below.
Chapter 2: Setting Up
19
2.1.3 Installing the Memory
Follow these instructions to install the memory modules on
the motherboard.
1. Locate the memory slots on the motherboard.
2. Press the memory slot locking levers in the direction of
the arrows as shown below.
3. Insert the memory module into the slot as shown below.
20
Chapter 2: Setting Up
4. When inserted properly, the memory slot locking levers
lock automaticaly onto the indentations at the ends of the
module.
5. Repeat these steps when installing a second memory
module.
Chapter 2: Setting Up
21
The following chart outlines the suggested rules for populating
memory.
22
Chapter 2: Setting Up
2.1.4 Installing Low Profile PCI-E Cards
There are two PCI-E card slots in your TA26 B5397 system.
Follow these instructions for PCI-E card installation.
1. Locate the PCI-E card slots on the motherboard. See
“System Internal View” on page 14 for the PCI-E slot
locations.
2. Unscrew the bracket from the slot you want to use.
3. Lift up the bracket.
4. Insert a PCI-E card with low profile bracket into the
appropriate slot. Secure the card with the screw you
removed from the bracket.
Chapter 2: Setting Up
23
2.1.5 Installing Hard Drives
The TA26 B5397 supports up to eight serial SAS/SATA hard
drives. Follow these instructions to install a hard drive.
1. Press the locking lever latch in the direction shown by the
arrow below. The latch will pop open.
2. Slide the HDD tray out.
3. Unscrew the tray from the base as shown.
24
Chapter 2: Setting Up
4. Remove the base.
5. Place a hard drive into the drive tray.
6. Screw the hard drive in place using 4 HDD screws.
7. Reinsert the tray into the bay and press the locking lever
to secure.
Chapter 2: Setting Up
25
2.1.6 Installing a Floppy Drive
This section describes how to install a floppy disk drive in the
TA26 B5397 if required.
Follow these instructions to install a floppy disk drive in the
TA26 B5397.
1. Remove the top, left hand drive tray from the TA26
B5397 as shown.
Note: The top, left hand drive bay is the only bay that can
accommodate a floppy disk drive.
2. Attach the supplied FDD rails to the floppy disk drive with
six (6) M3L5, BIN (+) screws. The wide end of the rails
should be pointing towards the front.
26
Chapter 2: Setting Up
Note: The FDD rails each have a flat side which should be
against the body of the floppy drive when installed. There is
also a spring catch mechanism on the right hand rail (when
looking at the floppy disk drive from the front).
3. Plug the FDD power and data cables into the ports on the
back of the floppy disk drive.
4. Thread the cables out through the back of the empty
drive bay. Slide the floppy disk drive into the drive bay
until it clicks into place and fits flush with the front panel.
Chapter 2: Setting Up
27
5. Connect the other end of the power cable to the connector (J37) on the backplane.
6. Connect the other end of the supplied FDD cable to the
FDD slot on the motherboard.
Note: To release the floppy disk drive from the drive bay,
you will need to press the release catch inside the chassis.
28
Chapter 2: Setting Up
2.2
Rack Mounting
After installing the necessary components, the Tank TA26
B5397 can be mounted in a rack using the supplied rack
mounting kit.
Rack mounting kit
Sliding Rails x 2
Mounting Ears x 2
Screws Kit x 1
Mounting Brackets x 4 (pre-installed)
2.2.1 Installing the Server in a Rack
Follow these instructions to mount the TA26 B5397 into an
industry standard 19" rack.
NOTE: Before mounting the Tank TA26 B5397 in a rack,
ensure that all internal components have been installed and
that the unit has been fully tested. Maintenance can be performed on the unit while in a rack but it is preferable to install
the device in a fully operational condition.
Screws List
No.
Size
Quantity
A
M4L6, S10C
(marked blue)
4
B
M6
8
C
M4-L5
18
Chapter 2: Setting Up
Screw
29
Attaching the Inner Rails to the Unit
7. Screw the handles to each side of TA26 B5397 as shown
using two (2) M4L6, S10C screws (A) from the supplied
screws kit.
8. Attach the inner rails both sides of the unit using nine (9)
M4-L5 screws (C) on each side.
30
Chapter 2: Setting Up
Installing Outer Rails to the Rack
1. Adjust the outer rail to match the length of the unit.
2. Secure the outer rail to the rack using 2 brackets and M6
screws (B) for each side. Secure the mounting brackets
from outside, not inside, of the rack.
Chapter 2: Setting Up
31
Rackmounting the Server
1. Draw out the middle rail to the latch position.
2. Lift the unit and then insert the inner slide rails into the
middle rails.
3. Push the unit in and press the latch key.
32
Chapter 2: Setting Up
4. Push the whole system into the rack.
5. Secure the mounting handles of the unit to the rack.
Note: To avoid injury, it is strongly recommended that two
people lift the TA26 B5397 into the place while a third person
screws it to the rack.
Chapter 2: Setting Up
33
NOTE
34
Chapter 2: Setting Up
Chapter 3: Replacing Pre-Installed
Components
3.1
Introduction
This chapter explains how to replace pre installed components including the motherboard, LED control board, USB
adapter board, HDD, and DVD-ROM drive, etc.
Take note of the precautions in this section when installing
your system.
3.1.1 Work Area
Make sure you have a stable, clean working environment.
Dust and dirt can get into components and cause malfunctions. Use containers to keep small components separated.
Putting all small components in separate containers keeps
them from becoming lost. Adequate lighting and proper tools
can prevent you from accidentally damaging the internal
components.
3.1.2 Tools
The procedures that follow require only a few tools, including
the following:
•
•
A cross head (Phillips) screwdriver
A grounding strap or an anti-static pad
Most of the electrical and mechanical connections can be disconnected using your fingers. It is recommended that you do
not use needle-nosed pliers to remove connectors as these
can damage the soft metal or plastic parts of the connectors.
Chapter 3: Replacing Pre-Installed Components
35
3.1.3 Precautions
Components and electronic circuit boards can be damaged
by static electricity. Working on a system that is connected to
a power supply can be extremely dangerous. Follow the
guidelines below to avoid damage to the Tank TA26 B5397 or
injury to yourself.
•
Ground yourself properly before removing the top
cover of the system. Unplug the power from your
computer power supply and then touch a safely
grounded object to release static charge (i.e. power
supply case). If available, wear a grounded wrist
strap. Alternatively, discharge any static electricity by
touching the bare metal chassis of the unit case, or
the bare metal body of any other grounded appliance.
•
Avoid touching motherboard components, IC chips,
connectors, memory modules, and leads.
•
The motherboard is pre-installed in the system.
When removing the motherboard, always place it on
a grounded anti-static surface until you are ready to
reinstall it.
•
Hold electronic circuit boards by the edges only. Do
not touch the components on the board unless it is
necessary to do so. Do not flex or stress circuit
boards.
•
Leave all components inside the static-proof packaging that they ship with until they are ready for installation.
•
After replacing optional devices, make sure all
screws, springs, or other small parts are in place and
are not left loose inside the case. Metallic parts or
metal flakes can cause electrical shorts.
Notes:
• All connectors are keyed to only attach one way.
• Always use the correct screw size as indicated in the
procedures.
36
Chapter 3: Replacing Pre-Installed Components
3.2
Disassembly Flowchart
The following flowchart outlines the disassembly procedure.
Rear Components
DIMMs
Chassis top cover
CPU/heatsink assembly
Mainboard
PCI-E card
Power supply
Mainboard
Front Components
Chassis top cover
DVD-ROM
PCBs
Control Board
FAN
Backplane
Note: The Tank TA26 B5397 should be always powered off
before disassembly.
Chapter 3: Replacing Pre-Installed Components
37
3.3
Removing the Cover
Before replacing any parts you must remove the chassis
cover.
Follow these instructions to remove the cover of the
Tank TA26 B5397 chassis cover.
1. Turn the screw on the back side. Then slide the chassis
cover in the direction of arrow.
2. Lift off the cover.
38
Chapter 3: Replacing Pre-Installed Components
3. Unscrew the fan duct.
Chapter 3: Replacing Pre-Installed Components
39
3.4
Replacing Motherboard Components
Follow these instructions to replace motherboard components, including the motherboard.
3.4.1 Disconnecting All Motherboard Cables
Before replacing the motherboard or certain components,
remove cables connected to the motherboard. Follow these
instructions to remove all motherboard cabling.
1. Disconnect power cables.
2. Disconnect the DVD-ROM drive cable, TYFP cables,
SAS/SATA hard drive cables, USB cable, and 2x7 pin fan
control cable.
40
Chapter 3: Replacing Pre-Installed Components
3.4.2 Removing the Motherboard
After removing all of the aforementioned cables, follow these
instructions to remove the motherboard from the chassis.
1. Remove ten mainboard screws and one fan duct screw
securing the motherboard to the chassis.
2. Remove the mainboard from the chassis.
Chapter 3: Replacing Pre-Installed Components
41
3.4.3 Removing the CPU Heatsink Mounting Plates
Follow these instructions to remove the CPU Heasink mounting plates.
1. Remove the eight CPU Heatsink mounting plate standoffs. They are the stand-offs to which you mount the
CPU heatsink.
2. Take out the black mylar from the chassis.
3. Unscrew the eight chassis mounting stand-offs to remove
the CPU Heatsink mounting plates from the chassis.
4. Refer to 2.5 Installing the Processor(s): CPU Heatsink
Mounting Plate Installation on your motherboard’s
User’s Guide for more information.
42
Chapter 3: Replacing Pre-Installed Components
3.5
Replacing the Slim DVD-ROM
Follow these instructions to replace the DVD-ROM.
1. Remove the FFC cable from the rear of the DVD-ROM
drive.
2. Press the tab in the direction shown to release the DVDROM drive.
3. Push the DVD-ROM drive through the front of the TA26
B5397.
Chapter 3: Replacing Pre-Installed Components
43
4. Remove the two screws that secure DVD-ROM drive to
the backplane.
5. Replace the DVD-ROM drive.
6. Secure the DVD-ROM to the backplane using two
screws. Then replace the unit into the drive bay and connect the DVD-ROM FFC cable.
44
Chapter 3: Replacing Pre-Installed Components
3.6
Replacing the LED Control Board
Follow these instructions to replace the LED control board.
1. Remove the screw securing the LED control board unit to
the chassis.
2. Remove the connector cables from the backplane.
3. Slide back the LED control board bracket and lift free of
the chassis.
Chapter 3: Replacing Pre-Installed Components
45
4. Remove the LED control board and USB cables from the
LED control board and USB adapter board.
5. Remove the five screws securing the LED control board
and USB adapter board to the bracket.
6. Release the LED control board and USB adapter board
from bracket. After replacement, insert and secure the
unit to the chassis following the above procedure in
reverse.
46
Chapter 3: Replacing Pre-Installed Components
3.6.1 LED Control Board Features
S3 power switch
JB1
SYSTEM
HEADER
S2 ID switch
S1 reset switch
D6 power LED
D5 HDD LED
D4 W/L LED
D3 ID LED
D2 LAN2 LED
D1 LAN1 LED
3.6.2 LED Control Board Connector Pin Definitions
JB1 2x12 Pin Output Connector
1
LAN1 GR-LED +
2
LAN1-LED -
3
Reserved
4
Reserved
5
LAN2 GR-LED +
6
LAN2-LED -
7
Reserved
8
Reserved
9
Reserved
10
Reserved
11
ID-LED +
12
ID-LED -
13
W-LED +
14
W-LED -
15
Local HDD led +
16
Local HDD led -
17
System power led +
18
System power led -
19
System reset switch +
20
System reset switch -
21
ID-switch +
22
ID-switch -
23
System power switch +
24
System power switch -
Chapter 3: Replacing Pre-Installed Components
47
3.7
Replacing the Backplane
Follow these instructions to replace the backplane in your
TA26 B5397 system.
1. Remove all of cables connected to the backplane, including fan cables, DVD-ROM cables, LED control board
cable, fan control cable, TYFP cable, USB cables, front
panel LED cables, power cables, and SAS/SATA cables.
Power cables
Fan cables
Slim DVD-ROM
FFC cable
LED control
board cable
USB cable
DVD-ROM cable
Fan control cable
TYFP cable
USB cable
Front panel LED cables
48
SAS/SATA cables
Chapter 3: Replacing Pre-Installed Components
2. Remove the ten screws to release the backplane.
3. Turn the locking keys at the base of the backplane as
shown.
4. Pull out the backplane.
5. Place a new backplane in position and secure in place
with the ten screws and locking keys released in step 2
and 3.
6. Reconnect all the cables to the backplane.
Chapter 3: Replacing Pre-Installed Components
49
3.7.1 M1220 SAS/SATA Backplane Features
Front View
J35 2x7pin
LED
J13 29pin SAS
J14 29pin SAS
J15 29pin SAS
J34 2x5pin LED
J11 29pin SAS
J12 29pin SAS
J7 40pin
cd-rom/B
J33 2x12pin
LED/B
J5 2x5pin USB
J36 2x7pin
LED
J8 29pin SAS
J9 29pin SAS
J10 29pin SAS
50
Chapter 3: Replacing Pre-Installed Components
Rear View
J1,J2,J3
big 4pin
FAN1 4pin
J25,J27,J29,J31
7pin secondary
J24,J26,J28,J30
7pin primary
J38 2x7pin
tach and PWM
J6 TO
CD-ROM
FAN2 4pin
J37 small
4pin
FAN3 4pin
J17,J19,J21,J23
7pin secondary
J16,J18,J20,J22
7pin primary
Chapter 3: Replacing Pre-Installed Components
J32 LED/B
J4 USB OUT
51
3.7.2 M1220 SAS/SATA Backplane Connector Pin Definitions
J32, J33 2x12pin LED board connector
1
LAN1 LED + (link/active)
2
LAN1 LED - (link/active)
3
Reserved
4
Reserved
5
LAN2 LED + (link/active)
6
LAN2 LED - (link/active)
7
Reserved
8
Reserved
9
Reserved
10
Reserved
11
ID-LED +
12
ID-LED -
13
W-LED +
14
W-LED -
15
M/B HDD LED +
16
M/B HDD LED -
17
M/B power LED +
18
M/B power LED -
19
M/B reset switch +
20
M/B reset switch -
21
ID-switch +
22
ID-switch -
23
M/B power switch +
24
M/B power switch -
J7 SILM IDE 40pin Front Panel Connector
52
1
RESET
2
GND
3
D7
4
D8
5
D6
6
D9
7
D5
8
D10
9
D4
10
D11
11
D3
12
D12
13
D2
14
D13
15
D1
16
D14
17
D0
18
D15
19
GND
20
VCC
21
DMARQ
22
VCC
23
DIOW
24
VCC
Chapter 3: Replacing Pre-Installed Components
25
DIOR
26
VCC
27
IORDY
28
CSEL
29
DMACK
30
VCC
31
INTRQ
32
IOCS16
33
DA1
34
PDIAG
35
DA0
36
DA2
37
CS1FX
38
CS3FX
39
DASP
40
VCC
Fan Signal Related Connector Pin Definitions
Note: The FAN signal naming is based on HW circuit
design only. It might be different from the system fan name.
FAN1, FAN2, FAN3: 4-pin Fan connector
1
GND
2
VDD +12V
3
TACH
4
PWM
J1, J2 and J3 power big 4-pin connector
1
VDD +12V
2
GND
3
GND
4
VCC +5V
Chapter 3: Replacing Pre-Installed Components
53
J4, J5 USB 2x5pin connector
1
USB1 power +
2
USB2 power +
3
USB1 DATA -
4
USB2 DATA -
5
USB1 DATA +
6
USB2 DATA +
7
USB1 GND
8
USB2 GND
9
Key pin
10
None
J37 power small 4-pin connector
1
+5V
2
GND
3
GND
4
+12V
J36 HDD LED pin out
1
PLED1
2
GND
3
ALED1
4
ALED1 +
5
PLED2 +
6
GND
7
ALED2 -
8
ALED2 +
9
PLED3 +
10
GND
11
ALED3 -
12
ALED3+
13
None
14
Key
J34 HDD LED pin out
54
1
PLED4 +
2
GND
3
ALED4 -
4
ALED4 +
5
PLED5 +
6
GND
7
ALED5 -
8
ALED5 +
9
None
10
Key
Chapter 3: Replacing Pre-Installed Components
J35 HDD LED pin out
1
PLED6 +
2
GND
3
ALED6 -
4
ALED6 +
5
PLED7 +
6
GND
7
ALED7 -
8
ALED7 +
9
PLED8 +
10
GND
11
ALED8 -
12
ALED8 +
13
None
14
Key
J38 2x7pin FAN tach and PWM pin out
1
FAN1 tach
2
Reserved
3
FAN2 tach
4
Reserved
5
FAN3 tach
6
Reserved
7
Reserved
8
Reserved
9
Reserved
10
Reserved
11
GND
12
KEY
13
GND
14
PWM input
Chapter 3: Replacing Pre-Installed Components
55
3.8
Replacing the System Fan
Follow these instructions to replace the cooling fans in your
TA26 B5397 system.
1. Locate the fan connector on the backplane and unplug
the fan cable as shown below.
2. Take the fan away from the chassis.
3. Replace a new fan into the chassis following the above
steps in reverse.
56
Chapter 3: Replacing Pre-Installed Components
3.9
Replacing the Power Supply
3.9.1 Standatd Power Supply
Follow these instructions to replace the power supply in your
TA26-B5397 system.
1. Remove the chassis cover. See “Removing the Cover” on
page 38 for more details.
2. Detach the power cables from the motherboard and
backplane. See “Disconnecting All Motherboard Cables”
on page 40 for more details.
3. Remove the three screws securing the power supply to
the chassis.
Chapter 3: Replacing Pre-Installed Components
57
4. Remove the two screws attaching the power supply to
the chassis interior and lift out the unit.
5. Lift the power supply free from the chassis.
6. Replace a new power supply into the chassis following
the above steps in reverse.
58
Chapter 3: Replacing Pre-Installed Components
3.9.2 Optional 1+1 Redundant Power Supply
If the optional 1+1 redundant power supply is fitted, either of
the two units can be hot swapped. Follow these instructions
to replace a single power unit with a redundant power supply
unit.
Note: Before proceeding, remove the new redundant power
supply from its packaging.
1. Remove the screws which fix the bracket to the sides of
the single power supply cage.
Chapter 3: Replacing Pre-Installed Components
59
2. Lift the power supply free from the chassis.
3. Lift the bracket free from the chassis.
4. Screw the bracket to the rear of the redundant power
supply cage.
60
Chapter 3: Replacing Pre-Installed Components
5. Insert the redundant power supply cage into the chassis.
6. Screw the cage to the chassis exterior.
7. Screw the cage to the chassis interior.
Chapter 3: Replacing Pre-Installed Components
61
8. Insert the new power supply unit and secure by turning
the locking screw.
62
Chapter 3: Replacing Pre-Installed Components
9. Reattach all power supply connector cables to the motherboard and backplane.
Chapter 3: Replacing Pre-Installed Components
63
NOTE
64
Chapter 3: Replacing Pre-Installed Components
Appendix I: BIOS Differences
The BIOS of B5397 is similar to the BIOS of S5397. There is
only one menu different. See the following for the differences
in BIOS between B5397 and S5397. For a complete review of
S5397 BIOS, refer to the motherboard manual.
Table of Differences
S5397 Mainboard
B5397 Barebone
CPU0
CPU1
Rear Chass FAN
Front Chass FAN
PCI FAN
System FAN
System Fan1
System Fan2
System Fan3
Auto Fan Control
[Disabled]
Auto Fan Control
[Enabled]
Azalia Audio
[Enabled]
Azalia Audio
[Disabled]
Onboard LSI SAS
ROM [Disabled]
Onboard LSI SAS
ROM [Enabled]
Advanced
Hardware Monitor
--> Fan Speed Monitoring
Integrated Devices
Appendix
65
Appendix II: Cable Connection Tables
SAS/SATA Cable
Table 1: TA26 B5397 Model
M1220 SAS/SATA
Backplane
Connects to
Motherboard
Æ
mini SAS0~3
Æ
mini SAS4~7
J16
J18
J20
J22
J24
J26
J28
J30
FAN Cable
Table 2: System Fan to Backplane
66
System Fan
Connects to
M1220 SAS/SATA
Backplane
Fan 1
Æ
FAN1 4-pin connector
Fan 2
Æ
FAN2 4-pin connector
Fan 3
Æ
FAN3 4-pin connector
Appendix
Power Supply Cable
Table 3: Power Supply to Motherboard
Power Supply
Connects to
Motherboard
P24 24-pin power
cable
Æ
PW2 24-pin connector
PA 8-pin power cable
Æ
PW4 8-pin connector
PB 4-pin power cable
Æ
PW1 4-pin connector
PC 4-pin power cable
Æ
PW3 4-pin connector
Table 4: Power Supply to Backplane
Power Supply
Connects to
M1220 SAS/SATA
Backplane
PD 4-pin power cable
Æ
J1 4-pin connector
PE 4-pin power cable
Æ
J2 4-pin connector
PF 4-pin power cable
Æ
J3 4-pin connector
Other Cables
Table 5: Backplane to Motherboard
M1220 SAS/SATA
Backplane
Connects to
J32 LED/B
Æ
J4 USB OUT
Æ
J41
J6 TO CD-ROM
Æ
IDE1
J38
2x7pin Tach and PWM
Æ
J33
Appendix
Motherboard
J28
J37
67
Table 6: Backplane to LED Control Board
M1220 SAS/SATA
Backplane (Rear side)
J33 2x12pin LED/B
J5 2x5pin USB
Connects to
LED Control Board
Æ
JB1 SYSTEM HEADER
Table 7: System Internal LED Cables to Backplane
M1220 SAS/SATA
Backplane (Front side)
Connects to
TA26 B5397 System
Æ
System Internal
LED Cables
J34 2x5pin LED
J35 2x7pin LED
J36 2x7pin LED
Table 8: DVD-ROM Related Cable
M1220 SAS/SATA
Backplane
Connects to
DVD-ROM Backplane
J7
slim DVD connector
Æ
DVD-ROM Backplane
Table 9: FDD Related Cables
68
Motherboard FDD
connector
Æ
FDD Drive
M1220 SAS/SATA
Backplane
J37 4-pin connector
Æ
FDD Drive
Appendix
Appendix III: Installing the SO-DIMM Card
The following provides you with the information on installing
the M3295-2/M3296 SMDC card into your TA26 B5397 system.
1. Locate the SO-DIMM TARO card socket on the motherboard. See “System Internal View” on page 14 for the
SO-DIMM socket location.
2. Press the SO-DIMM socket locking levers in the direction
of the arrows as shown below.
3. Insert the TARO card into the socket as shown below.
Appendix
69
4. When inserted properly, the SO-DIMM socket locking
levers lock automaticaly onto the indentations at the ends
of the TARO card.
70
Appendix
Appendix IV: FRU Parts List
TA26-B5397 FRU Parts
Item
Model Number
Motherboard
S5383WG4NR
Chassis Unit
CCHA-0090
Chassis Top
Cover
Drive Tray
Power Supply
Part Number
Picture
Quantity
Description
1
TYAN S5397WAG2NRF
Motherboard
432731500003
1
TA26 2U Chassis
CCCV-0020
340731500032
1
Top Cover for TA26 Chassis
CHDT-0030
340731500035
8
Removable 3.5" HDD Tray
CPSU-0160
471172400087
1
700W Single Power Supply
CPSU-0350
471015200193
2
700W 1+1 redundant PSU module
CPSU-0351
471015200197
1
700W 1+1 redundant PSU cage
CMPT-0150
342772500002
1
700W 1+1 redundant PSU
bracket_1
CMPT-0151
342772500003
1
700W 1+1 redundant PSU
bracket_2
CFAN-0250
336252012306
2
80X80X38mm Fan, 12V, 7500rpm,
4-pin
CFAN-0200
336252012269
1
60X60X38mm Fan, 12V, 8000rpm,
4-pin
FAN
Appendix
71
TA26-B5397 FRU Parts
Item
Heat Sink &
Cooler
PCBA
Model Number
Part Number
Picture
Quantity
Description
CHSK-0330
343772500003
2
LGA771 CPU Heatsink
CHSB-0080
342748500001
2
CEK Spring for LGA771
CHSB-0120
340772500001
2
CPU Backplane Kit
CPCA-0270
1
Front Control Board
M1220
1
SAS/SATA 8-port Backplane, Dual
Host
CPCA-0080
1
Front Control Board
CPCA-0250
1
Slim DVD ROM Adapter Board
M3295-2
1
SMDC Card
M3296
1
SMDC Card
M1212
1
SCSI 8-port Backplane
CDVD-0020
523410299023
1
Slim DVD ROM
CFDD-0010
523411442080(TF)
523411442047
1
3.5" FDD, Black
Peripheral Drives
& Parts
72
Appendix
TA26-B5397 FRU Parts
Item
Rack Mounting
Part
Cable Set
Appendix
Model Number
Part Number
Picture
Quantity
Description
CEAR-0100
340731500062
1
Mounting Ear Left
CEAR-0110
340731500063
1
Mounting Ear Right
CRAL-0040
340755700002
1
Slide Rail Kit
CCBL-0310
332810000280
1
A/C Power Cord, 2440mm, US Type
CCBL-0300
332810000281
1
A/C Power Cord, 1800mm, Germany
Type
CCBL-067C
422772500001
1
Mini SAS Cable, 36P to 4X7P,
400mm
CCBL-067D
422772500002
1
Mini SAS Cable, 36P to 4X7P,
300mm
CCBL-0130
422732600022
1
Slim CD ROM FFC Cable
CCBL-0090
422732600023
1
HDD LED Cable, 10-pin, 200mm
CCBL-0100
422732600024
2
HDD LED Cable, 14-pin, 200mm
73
TA26-B5397 FRU Parts
Item
74
Model Number
Part Number
Picture
Quantity
Description
CCBL-0111
422763200001
1
Control Board Cable
CCBL-0358
422763200005
1
USB Internal Cable, MB to
Backplane, 300mm
CCBL-0359
422763200006
1
USB Cable, Backplane to LED
Board, 130mm
CCBL-0120
422732600018
1
LED Board Cable, 253mm
CCBL-0433
422740900009
1
DVD ROM Cable, 395mm
CCBL-0144
422763200004
1
Chassis Intrusion Cable, 800mm
CCBL-0841
422763200002
1
FAN Cable, 380mm
CCBL-0810
422732600020
1
Floppy Cable, 610mm
CCBL-0820
422732600021
1
Floppy Power Cable, 90mm
CCBL-0250
422731500032
2
SCSI Cable, 68-pin, MB to
Backplane, 480mm
CCBL-0260
422731500033
1
SCSI Cable, 68-pin, Daisy
Chaining, 35mm
Appendix
Technical Support
If a problem arises with your system, you should first turn to
your dealer for direct support. Your system has most likely
been configured or designed by them and they should have
the best idea of what hardware and software your system
contains. Hence, they should be of the most assistance for
you. Furthermore, if you purchased your system from a
dealer near you, take the system to them directly to have it
serviced instead of attempting to do so yourself (which can
have expensive consequences).
If these options are not available for you then TYAN Computer Corporation can help.Besides designing innovative and
quality products for over a decade, TYAN has continuously
offered customers service beyond their expectations. TYAN's
website
(www.tyan.com) provides easy-to-access resources such as
in-depth Linux Online Support sections with downloadable
Linux drivers and comprehensive compatibility reports for
chassis, memory and much more. With all these convenient
resources just a few keystrokes away, users can easily find
the latest software and operating system components to keep
their systems running as powerful and productive as possible. TYAN also ranks high for its commitment to fast and
friendly customer support through email. By offering plenty of
options for users, TYAN serves multiple market segments
with the industry's most competitive services to support them.
"TYAN's tech support is some of the most impressive we've
seen, with great response time and exceptional organization
in general" - Anandtech.com
Please feel free to contact us directly for this service at techsupport@tyan.com
Help Resources:
1. See the beep codes section of this manual.
75
Technical Support
2. See the TYAN website for FAQ’s, bulletins, driver updates,
and other information: http://www.tyan.com
3. Contact your dealer for help BEFORE calling TYAN.
4. Check the TYAN user group: alt.comp.periphs.mainboard.TYAN
Returning Merchandise for Service
During the warranty period, contact your distributor or system
vendor FIRST for any product problems. This warranty only
covers normal customer use and does not cover damages
incurred during shipping or failure due to the alteration, misuse, abuse, or improper maintenance of products.
NOTE: A receipt or copy of your invoice marked with the date
of purchase is required before any warranty service can be
rendered. You may obtain service by calling the manufacturer
for a Return Merchandise Authorization (RMA) number. The
RMA number should be prominently displayed on the outside
of the shipping carton and the package should be mailed prepaid. TYAN will pay to have the board shipped back to you.
TYAN Tank TA26 B5397 User’s Manual v1.0
Document part No. D1941-100
Technical Support
76
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising