CITROËN NaviDrive 3D Navigation System Installation Handbook

CITROËN ALERT ZONES
I N S T A L L A T I O N H A N D B O O K N a v i D r iv e 3 D
CITROËN ALERT ZONES
INSTALLATION HANDBOOK NaviDrive 3D
1. INSTALLING
INSTALLING THE FILE ON THE NAVIGATION SYSTEM
Once you have downloaded the Alert Zones file from
the CITROËN website you must install it on the hard
disk drive of your NaviDrive 3D navigation system
(which contains the Europe digital mapping system
required to guide you).
To install your Radars file on your NaviDrive 3D, use
either an SD card or a USB stick (preferably blank to
avoid any potential recognition issues with the
medium).
After inserting the SD card or USB stick into your
computer, select file (.exe):
1. Click on “Exécuter” (Run) or “Ouvrir” (Open), and
this will call up a “Self-extracting Archive” window on
your computer’s screen (see example on RH side).
right of “Extract to” in order
2. Click on the button
to select the SD card or USB stick you wish the data to
be copied onto.
3. Click on “ Start”.
To check that the copy has been successful, you may
check the SD card or USB stick for the presence of the:
- pkgdb folder (and subfolders)
- config.nfm file.
Once the data has been successfully copied you may
remove the data medium from your computer and
return to your vehicle to install the Alert Zones file on
your NaviDrive 3D navigation system.
August 2012 - 2
CITROËN ALERT ZONES
INSTALLATION HANDBOOK NaviDrive 3D
To install the Alert Zones file on your navigation
system, connect the data medium as follows:
- SD card:
card card reader on NaviDrive 3D frontpanel
- USB stick:
stick port located under central armrest at
the front
Having done so you should then press the “NAV”
key and select the following menus:
- “ Navigation »
- Then “Settings“
- and “Update personal POI“
Select the data medium you inserted in NaviDrive
3D and on which the Alert Zones file has been
copied (USB stick in the example opposite).
August 2012 - 3
CITROËN ALERT ZONES
INSTALLATION HANDBOOK NaviDrive 3D
Confirm installation of the Alert Zones file by
clicking on “YES” (after reading the warning about
erasing of previous data). File installation will only
take a few seconds.
Once installation is complete, a message will
prompt you to confirm the restart of the navigation
system.
Your NaviDrive 3D will then ask you to eject the
data medium (and only then).
then)
Confirm with “OK” once the operation has been
completed.
August 2012 - 4
CITROËN ALERT ZONES
INSTALLATION HANDBOOK NaviDrive 3D
2. CONFIGURING RADAR WARNINGS ON THE NAVIGATION SYSTEM
To configure warnings on your NaviDrive 3D
navigation system, press the “ NAV” key and
select the following menus:
- “Navigation Menu”
- Then “Settings”
- Then “Set parameters for risk area”
An information message will be displayed, confirm
by clicking on “OK” once you have read it.
August 2012 - 5
CITROËN ALERT ZONES
INSTALLATION HANDBOOK NaviDrive 3D
We recommend the following configuration:
- Activate the display on the map
- Activate visual alert on approach
- Activate sound alert on approach
With this configuration, you benefit from the
following features:
- Audio advance warning followed by
audible warning (beep) when approaching
a high-risk area
- Visual warning:
warning the navigation system
screen displays the distance and the
associated Citroën Alert Zone pictogram.
The permitted speed limit is also
displayed in the event of fixed speed
cameras*
These are the Citroën Alert Zone pictograms :
Fixed speed camera*:
Traffic light camera*:
Entering a high-risk area*:
The visual warning is only displayed on approach
to the high-risk area.
*Depending on the country’s legislation,
information about fixed speed cameras and traffic
light cameras may be prohibited; if this is the case,
then only information about high-risk areas will be
displayed.
Example of a fixed speed camera warning in Map
mode (in countries where this function is
permitted)
August 2012 - 6
CITROËN ALERT ZONES
INSTALLATION HANDBOOK NaviDrive 3D
Example of a fixed speed camera warning when
not in Mode (in countries where this function is
permitted)
August 2012 - 7