NEC | LCD4620-2-AVT | User`s manual | NEC LCD5220, w/TVBOX

NEC LCD5220, w/TVBOX
User’s Manual
MultiSync LCD4020
MultiSync LCD4620
MultiSync LCD5220
Index
Declaration of conformity ............................................................................................................................. English-1
Important Information ................................................................................................................................... English-2
Warning, Caution ................................................................................................................................ English-2
Declaration ................................................................................................................................................... English-2
Safety Precautions, Maintenance & Recommended Use ............................................................................ English-3
Contents ....................................................................................................................................................... English-4
Installation .................................................................................................................................................... English-5
Parts Name and Functions .......................................................................................................................... English-8
Control Panel ...................................................................................................................................... English-8
Terminal Panel .................................................................................................................................... English-9
Wireless Remote Control ................................................................................................................... English-10
Operating Range for the Remote Control ........................................................................................... English-11
Handling the remote control ........................................................................................................... English-11
Setup.............................................................................................................................................................English-12
Connections ................................................................................................................................................. English-14
Wiring Diagram ................................................................................................................................... English-14
Connecting a Personal Computer ...................................................................................................... English-15
Connect the LCD Monitor to a Personal Computer ........................................................................ English-15
Connecting to a Macintosh Computer ................................................................................................ English-16
Connect the LCD Monitor to Macintosh ......................................................................................... English-16
Connecting with Digital Interface Equipment ...................................................................................... English-17
Connect the LCD Monitor to a Computer with a Digital Output ...................................................... English-17
Connecting a DVD Player with component out .................................................................................. English-18
Connect the LCD Monitor to a DVD Player .................................................................................... English-18
Connecting a DVD Player with HDMI out ........................................................................................... English-19
Connect the LCD Monitor to a DVD Player .................................................................................... English-19
Connecting a DVD Player with SCART out ........................................................................................ English-19
Connect the LCD Monitor to a DVD Player .................................................................................... English-19
Connecting to a Stereo Amplifier ........................................................................................................ English-20
Connect the LCD Monitor to a Stereo Amplifier ............................................................................. English-20
Basic Operation ........................................................................................................................................... English-21
Power ON and OFF Modes ................................................................................................................ English-21
Power Indicator .................................................................................................................................. English-22
Using Power Management ................................................................................................................. English-22
Selecting a video source .................................................................................................................... English-22
Picture Size ........................................................................................................................................ English-22
Picture Mode ...................................................................................................................................... English-22
Information OSD ................................................................................................................................. English-22
OSD (On-Screen-Display) Controls ............................................................................................................. English-23
PICTURE ............................................................................................................................................ English-24
ADJUST ............................................................................................................................................. English-24
AUDIO ................................................................................................................................................ English-25
SCHEDULE ........................................................................................................................................ English-25
PIP ...................................................................................................................................................... English-26
OSD .................................................................................................................................................... English-26
MULTI DISPLAY ................................................................................................................................. English-27
DISPLAY PROTECTION .................................................................................................................... English-27
ADVANCED OPTION ......................................................................................................................... English-28
Connecting to a TV (For U.S.) ............................................................................................................ English-30
Connecting to a TV (For Europe) ....................................................................................................... English-32
Controlling the LCD monitor via RS-232C Remote Control ......................................................................... English-36
Features ....................................................................................................................................................... English-37
Troubleshooting ........................................................................................................................................... English-38
Specifications - LCD4020 ............................................................................................................................ English-39
Specifications - LCD4620 ............................................................................................................................ English-40
Specifications - LCD5220 ............................................................................................................................ English-41
Pin Assignment ............................................................................................................................................ English-42
Manufacturer’s Recycling and Energy Information ...................................................................................... English-43
www.necdisplaysolutions.com
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
U.S. Responsible Party:
Address:
Tel. No.:
NEC Display Solutions of America, Inc.
500 Park Boulevard, Suite 1100
Itasca, Illinois 60143
(630) 467-3000
Type of Product:
Computer Monitor
Equipment Classification:
Class B Peripheral
Model:
MultiSync LCD4020 (L406T6)
MultiSync LCD4620 (L466T7)
MultiSync LCD5220 (L527TE)
We hereby declare that the equipment specified above
conforms to the technical standards as specified in the FCC Rules.
Windows is a registered trademark of Microsoft Corporation. NEC is a registered trademark of NEC Corporation.
OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and Switzerland.
All other brands and product names are trademarks or registered trademarks of their respective owners.
Canadian Department of Communications Compliance Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.
FCC Information
1. Use the attached specified cables with the MultiSync LCD4020 (L406T6)/MultiSync LCD4620 (L466T7)/MultiSync LCD5220
(L527TE) colour monitor so as not to interfere with radio and television reception.
(1) Please use the supplied power cord or equivalent to ensure FCC compliance.
(2) Please use the supplied shielded video signal cable, Mini D-SUB 15 pin to Mini D-SUB 15 pin.
2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington,
D.C., 20402, Stock No. 004-000-00345-4.
The product you purchased may not have this feature.
LCD4020-BK-AV, LCD4020-2-AV, LCD4020-BK-AVT, LCD4020-2-AVT
LCD4620-BK-AV, LCD4620-2-AV, LCD4620-BK-AVT, LCD4620-2-AVT
LCD5220-BK-AV, LCD5220-BK-AVT only
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
English-1
English
DECLARATION OF CONFORMITY
Important Information
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS
THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM
WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE
POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit
has been included. Therefore, it should be read carefully in order to avoid any problems.
CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not
supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the
AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.
North America
European
Continental
U.K.
Chinese
Japanese
Region
U.S.A./Canada
EU (except U.K.)
U.K.
China
Japan
Voltage
120*
230
230
220
100
Plug Type
Plug Shape
*When operating the MultiSync LCD4020/MultiSync LCD4620/MultiSync LCD5220 monitor with its AC 125-240V power
supply, use a power supply cord that matches the power supply voltage of the AC power outlet being used.
NOTE: This product can only be serviced in the country where it was purchased.
Declaration
Declaration of the Manufacturer
We hereby certify that the color monitor MultiSync
LCD4020 (L406T6)/MultiSync LCD4620 (L466T7)/
MultiSync LCD5220 (L527TE) are in compliance with
and marked with
Council Directive 2006/95/EC:
– EN 60950-1
Council Directive 2004/108/EC:
– EN 55022
– EN 61000-3-2
– EN 61000-3-3
– EN 55024
NEC Display Solutions, Ltd.
4-13-23, Shibaura,
Minato-Ku
Tokyo 108-0023, Japan
English-2
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE
FOLLOWING WHEN SETTING UP AND USING
THE MULTI-FUNCTION MONITOR:
•
Recommended Use
DO NOT OPEN THE MONITOR. There are no user
serviceable parts inside and opening or removing covers
may expose you to dangerous shock hazards or other risks.
Refer all servicing to qualified service personnel.
•
For optimum performance, allow 20 minutes for warm-up.
•
Rest your eyes periodically by focusing on an object at least
5 feet away. Blink often.
•
Position the monitor at a 90° angle to windows and other
light sources to minimize glare and reflections.
•
Do not spill any liquids into the cabinet or use your monitor
near water.
•
Clean the LCD monitor surface with a lint-free, non-abrasive
cloth. Avoid using any cleaning solution or glass cleaner!
•
Do not insert objects of any kind into the cabinet slots, as
they may touch dangerous voltage points, which can be
harmful or fatal or may cause electric shock, fire or
equipment failure.
•
Adjust the monitor’s brightness, contrast and sharpness
controls to enhance readability.
•
Avoid displaying fixed patterns on the monitor for long
periods of time to avoid image persistence (after image
effects).
•
Get regular eye checkups.
•
Do not place any heavy objects on the power cord.
Damage to the cord may cause shock or fire.
•
Do not place this product on a sloping or unstable cart,
stand or table, as the monitor may fall, causing serious
damage to the monitor.
•
Ergonomics
The power supply cord you use must have been approved
by and comply with the safety standards of your country.
(Type H05VV-F 3G 1mm2 should be used in Europe)
To realize the maximum ergonomic benefits, we recommend
the following:
•
Use the preset Size and Position controls with standard
signals.
•
In UK, use a BS-approved power cord with molded plug
having a black (13A) fuse installed for use with this monitor.
•
Use the preset Color Setting.
•
Use non-interlaced signals.
•
Do not place any objects onto the monitor and do not use
the monitor outdoors.
•
•
The lamps in this product contain mercury. Please
dispose according to state, local or federal law.
Do not use primary color blue on a dark background, as it is
difficult to see and may produce eye fatigue due to
insufficient contrast.
Cleaning the LCD Panel
•
Do not bend, crimp or otherwise damage the power cord.
•
•
If glass is broken, handle with care.
When the liquid crystal panel is stained with dust or dirt,
please wipe with soft cloth gently.
•
Do not cover vent on monitor.
•
Please do not rub the LCD panel with hard material.
•
Do not use monitor in high temperature, humid, dusty, or
oily areas.
•
Please do not apply pressure to the LCD surface.
•
Please do not use OA cleaner it will cause deterioration or
discolor on the LCD surface.
•
If monitor or glass is broken, do not come in contact with the
liquid crystal and handle with care.
•
Allow adequate ventilation around the monitor, so that heat
can properly dissipate. Do not block ventilated openings or
place the monitor near a radiator or other heat sources.
Do not put anything on top of the monitor.
•
The power cable connector is the primary means of
detaching the system from the power supply. The monitor
should be installed close to a power outlet, which is easily
accessible.
•
Handle with care when transporting. Save packaging for
transporting.
•
Please clean the holes of back cabinet to reject dirt and
dust at least once a year because of set reliability.
•
If using the cooling fan continuously, it’s recommended to
wipe holes a minimum of once a month.
Cleaning the Cabinet
•
Unplug the power supply
•
Gently wipe the cabinet with a soft cloth
•
To clean the cabinet, dampen the cloth with a neutral
detergent and water, wipe the cabinet and follow with a dry
cloth.
NOTE: The surface of the cabinet is composed of many types
of plastic. DO NOT clean with benzene thinner, alkaline
detergent, alcoholic system detergent, glass cleaner,
wax, polish cleaner, soap powder, or insecticide.
Rubber or vinyl should not be in contact with the cabinet
for an extended period of time. These types of fluids
and materials can cause the paint to deteriorate, crack
or peel.
Immediately unplug your monitor from the wall outlet and refer
servicing to qualified service personnel under the following
conditions:
•
When the power supply cord or plug is damaged.
•
If liquid has been spilled, or objects have fallen into the
monitor.
•
If the monitor has been exposed to rain or water.
•
If the monitor has been dropped or the cabinet damaged.
•
If the monitor does not operate normally by following
operating instructions.
English-3
English
Safety Precautions, Maintenance & Recommended Use
Contents
Your new MultiSync monitor box* should contain the following:
•
LCD monitor
•
Cable Cover
•
Power Cord*1
•
Clamp x 3
•
Video Signal Cable
•
Screw (M4 x 10) x 9
•
User’s Manual
•
CD-ROM
•
Wireless Remote Control and AA Batteries
•
Thumbscrew for stand x 2
Video Signal Cable
(Mini D-SUB 15 pin to
Mini D-SUB 15 pin)
Screw (M4 x 10) x 9
Thumbscrew for stand x 2
Power Cord*1
Clamp x 3
User’s Manual
CD-ROM
Cable cover
User’s Manual
Wireless Remote Control
and AA Batteries
*1 Type and number of power cords included will depend on the where the LCD monitor is to be shipped. When more than
one power cord is included, please use a power cord that matches the AC voltage of the power outlet and has been
approved by and complies with the safety standard of your particular country.
*
Depending on where the LCD is sold, the stand may or may not be included with some models.
*
Remember to save your original box and packing material to transport or ship the monitor.
English-4
This device cannot be used or installed without the Tabletop
Stand or other mounting accessory for support. For proper
installation it is strongly recommended to use a trained,
NEC authorized service person. Failure to follow NEC
standard mounting procedures could result in damage to the
equipment or injury to the user or installer. Product warranty
does not cover damage caused by improper installation.
Failure to follow these recommendations could result in
voiding the warranty.
English
Installation
Orientation
•
When using the display in the portrait position, the
monitor should be rotated clockwise so that the left side
is moved to the top and the LED indicator light is on the
bottom. This will allow for proper ventilation and will
extend the lifetime of the monitor. Improper ventilation
may shorten the lifetime of the monitor.
Mounting
DO NOT mount the monitor yourself. Please ask dealer. For
proper installation it is strongly recommended to use a
trained, qualified technician. Please inspect the location
where the unit is to be mounted. Mounting on wall or ceiling
is the customer’s responsibility. Not all walls or ceilings are
capable of supporting the weight of the unit. Product
warranty does not cover damage caused by improper
installation, remodelling, or natural disasters. Failure to
comply with these recommendations could result in voiding
the warranty.
DO NOT block ventilated openings with mounting
accessories or other accessories.
LED Indicator
For NEC Qualified Personnel:
To insure safe installation, use two or more brackets to
mount the unit. Mount the unit to at least two points on the
installation location.
Please note the following when mounting
on wall or ceiling
•
•
When using mounting accessories other than those that
are NEC approved, they must comply with the VESAcompatible (FDMlv1) mounting method.
NEC strongly recommends
Unit
Mounting
using size M6 screws
Bracket
(10 mm (LCD4020/
LCD4620) or 12 mm
(LCD5220) + thickness of
Screw
bracket in length). If using
10 mm
Thickness
or
screws longer than 10 mm
12 mm
of Bracket
(LCD4020/LCD4620) or
12 mm (LCD5220), check
Screw length should
the depth of the hole.
equal depth of hole (10mm
(Recommended Fasten
(LCD4020/LCD4620) or
Force: 470 - 635N•cm)
12mm (LCD5220)) + the
NEC recommends mounting thickness of mounting bracket.
interfaces that comply with
UL1678 standard in North America.
•
Prior to mounting, inspect the installation location to
insure that it is strong enough to support the weight of
the unit so that the unit will be safe from harm.
•
Refer to the instructions included with the mounting
equipment for detailed information.
Mounting location
•
The ceiling and wall must be strong enough to support
the monitor and mounting accessories.
•
DO NOT install in locations where a door or gate can hit
the unit.
•
DO NOT install in areas where the unit will be subjected
to strong vibrations and dust.
•
DO NOT install near where the main power supply
enters the building.
•
Do not install in where people can easily grab and hang
onto the unit or the mounting apparatus.
•
When mounting in a recessed area, as in a wall, leave at
least 4 inches (10cm) of space between the monitor and
the wall for proper ventilation.
•
Allow adequate ventilation or provide air conditioning
around the monitor, so that heat can properly dissipate
away from the unit and mounting apparatus.
Mounting on ceiling
•
Ensure that the ceiling is sturdy enough to support the
weight of the unit and the mounting apparatus over time,
against earthquakes, unexpected vibrations, and other
external forces.
•
Be sure the unit is mounted to a solid structure within the
ceiling, such as a support beam. Secure the monitor
using bolts, spring lock washers, washer and nut.
•
DO NOT mount to areas that have no supporting internal
structure. DO NOT use wood screws or anchor screws
for mounting. DO NOT mount the unit to trim or to
hanging fixtures.
Maintenance
•
Periodically check for loose screws, gaps, distortions, or
other problems that may occur with the mounting
apparatus. If a problem is detected, please refer to
qualified personnel for service.
•
Regularly check the mounting location for signs of
damage or weakness that may occur over time.
English-5
2. Installing and removing optional table
top stand
Attaching Mounting Accessories
The display is designed for use with the VESA mounting
system.
CAUTION: Installing and removing the stand must be done
by four or more people (LCD5220), by two or
more people (LCD4020/LCD4620).
1. Attach Mounting Accessories
Be careful to avoid tipping monitor when attaching
accessories.
To install, follow those instructions included with the stand or
mounting apparatus. Use only those devices recommended
by the manufacturer.
LCD4020/LCD4620
Using 8 holes
Handle with care when mounting LCD monitor stand and
avoid pinching your fingers.
Optional table top stand
Table
Protective Sheet
NOTE: Place stand onto monitor so that the long end of the
feet are in the front.
Using 6 holes
3. Ventilation Requirements
LCD5220
When mounting in an enclosed space or recessed area,
leave adequate room between the monitor and the
enclosure to allow heat to disperse, as shown below.
VESA Mounting Interface
Figure 1
Mounting accessories can be attached with the monitor in
the face down position. To avoid damaging the screen face,
place the protective sheet on the table underneath the LCD.
The protective sheet was wrapped around the LCD in the
original packaging. Make sure there is nothing on the table
that can damage the monitor.
When using mounting accessories other than NEC
compliant and approved, they must comply with the VESAcompatible mounting method.
English-6
When using the display with the Tabletop Stand fasten the
LCD to a wall using a cord or chain that can support the
weight of the monitor in order to prevent the monitor from
falling. Fasten the cord or chain to the monitor using the
provided clamp and screw.
LCD4020: 278 mm
LCD4620: 210 mm
LCD5220: 400 mm
Screw Holes
Cord or chain
Clamp
Screw
Before attaching the LCD monitor to the wall, make sure
that the wall can support the weight of the monitor.
Be sure to remove the cord or chain from the wall before
moving the LCD.
English-7
English
4. Prevent Tipping
Parts Name and Functions
Control Panel
ON
LCD4020/LCD4620
OFF
LCD5220
1 POWER button ( )
7 DOWN ( ) button
Switches the power on/off. See also page 21.
Activates the OSD menu when the OSD menu is turned-off.
Acts as button to move the highlighted area down to
select adjustment items within OSD menu.
2 MUTE button (LCD5220 only)
Switches the audio mute ON/OFF.
8 EXIT button
3 INPUT button
Acts as SET button within OSD menu. (Toggle switches
between [DVI], [VGA], [RGB/HV], [HDMI]*, [DVD/HD]*,
[VIDEO]*, [S-VIDEO]* or [TV]*). [S-VIDEO] is enabled by
selecting the “SEPARATE” mode in the OSD or by having
the “S-VIDEO” cable connected with the “S-VIDEO” signal
present and selecting “PRIORITY” MODE. See page 28.
4 PLUS (+) button
Acts as (+) button to increase the adjustment with OSD menu.
Increases the audio output level when the OSD menu is
turned off*.
5 MINUS (-) button
Acts as (-) button to decrease the adjustment with OSD menu.
Decreases the audio output level when the OSD menu is
turned off*.
Activates the OSD menu when the OSD menu is turned-off.
Acts as EXIT button within the OSD to move to previous
menu.
9 Remote control sensor and Power Indicator
Receives the signal from the remote control (when using the
wireless remote control). See also page 11.
Glows green when the LCD monitor is in active mode*.
Glows red when the LCD is in POWER OFF (ECO standby)
mode. Glows amber when the LCD is in POWER OFF
(standby) mode. Blinks amber when the monitor is in Power
Save Mode. Green and Amber blink alternately while in
Power Standby mode with the “SCHEDULE SETTINGS”
function enabled. When a component failure is detected
within the monitor, the indicator will blink red.
* If “OFF” is selected in “POWER INDICATOR” (see page 22),
LED will not light when the LCD monitor is in active mode.
10 Main Power Switch
6 UP ( ) button
On/Off switch to turn main power ON/OFF.
Activates the OSD menu when the OSD menu is turned-off.
Acts as button to move the highlighted area up to select
adjustment items within OSD menu.
Control Key Lock Mode
This control completely locks out access to all Control Key
functions. To activate the control key lock function, press both
and and hold down simultaneously for more than
3 seconds. To resume user mode, press both and and
hold simultaneously for more than 3 seconds.
*: The product you purchased may not have this feature.
English-8
English
Terminal Panel
LCD4020/LCD4620
LCD5220
In
Out
1 AC IN connector
10 VIDEO INPUT/OUTPUT Connector*
Connects with the supplied power cord.
VIDEO IN connector (BNC and RCA): To input a
composite video signal. BNC and RCA connectors are not
available at the same time (Use only one input).
VIDEO OUT connector (BNC): To output the composite
video signal from the VIDEO IN connector.
S-VIDEO IN connector (Mini DIN 4 pin): To input the
S-video (Y/C separate signal). See page 28, S-VIDEO
MODE SETTING.
2 DVI IN (DVI-D)
To input digital RGB signals from a computer or HDTV
device having a digital RGB output.
* This connector does not support analog input.
3 VGA IN (mini D-Sub 15 pin)
To input analog RGB signals from a personal computer or
from other RGB equipment.
11 EXTERNAL CONTROL (D-Sub 9 pin)
4 RGB/HV IN [R, G, B, H, V] (BNC)
To input analog RGB signals or signals from other RGB
equipment.
This is also to connect equipment such as a DVD player,
HDTV device and Set-Top-Box. A Sync-on-Green signal can
be connected to the G connector.
5 RGB/HV OUT (BNC)
To outputs the signal from the RGB/HV IN connector to an
input on a separate device.
IN connector: Connect RS-232C input from external
equipment such as a PC in order to control RS-232C
functions.
Out connector: Connect RS-232C output. To connect
multiple MultiSync monitors via RS-232C daisy Chain.
12 EXTERNAL SPEAKER TERMINAL*
To output the audio signal from AUDIO 1, 2, 3, HDMI and
TV jack.
Note: This speaker terminal is for 15W + 15W (8 ohm)
speaker.
13 RF IN* (For U.S.)
6 HDMI connector*
TV signal input.
To input digital HDMI signals.
14 S/PDIF OUTPUT* (For U.S.)
7 DVD/HD connector* (RCA)
Optical digital audio out.
Connecting equipment such as a DVD player, HDTV device,
or Set-Top-Box.
15 Antenna Input* (For Europe)
Connects to antenna or to TV signal.
8 AUDIO IN* 1, 2, 3
16 Kensington Lock
To input audio signal from external equipment such as a
computer, VCR or DVD player.
For security and theft prevention.
*: The product you purchased may not have this feature.
9 AUDIO OUT*
To output the audio signal from the AUDIO IN 1, 2, 3, HDMI, and
TV jack to an external device (stereo receiver, amplifier, etc.).
English-9
Wireless Remote Control
7 KEYPAD
Press buttons to set and change passwords, change
channel and set REMOTE ID.
8 ENT button*
Sets channels.
9 DISPLAY button
Turns on/off the information OSD. See page 22.
10 MENU button
Turns on/off the menu mode.
11 AUTO SETUP button
Enters auto setup menu. See page 24.
12 EXIT button
Returns to previous menu within OSD menu.
13 UP/DOWN button
button to move the highlighted area up or
Acts as
down to select adjustment items within OSD menu.
Small screen which adjusted “PIP” mode moves up or down.
14 MINUS/PLUS (+/-) button
Increases or decreases the adjustment level within OSD
menu settings.
Small screen which adjusted “PIP” mode moves left or right.
15 SET button
Makes selection.
1 POWER button
16 VOLUME UP/DOWN button*
Switches the power on/off.
Increases or decreases audio output level.
2 INPUT button
17 CH +/- button*
Selects input signal, [DVI], [VGA], [RGB/HV], [HDMI]*,
[DVD/HD]*, [VIDEO]*, [TV]* or [S-VIDEO]*.
[S-VIDEO] is enabled by selecting the “SEPARATE” mode in
the OSD or by having the “S-VIDEO” cable connected with
an “S-VIDEO” signal present and selecting “PRIORITY”
MODE in the S-VIDEO OSD menu. See page 28.
Moves channel up or down.
18 CH RTN button*
Returns to previous channel.
19 MUTE button
Turns on/off mute function.
3 PICTURE MODE button
STILL button
Selects picture mode, [HIGHBRIGHT], [STANDARD],
[sRGB], [CINEMA]*. See page 22.
ON/OFF button: Activates/deactivates still picture mode.
STILL CAPTURE button: Captures still picture.
HIGHBRIGHT: for moving images such as DVD
STANDARD: for images
sRGB: for text based images
CINEMA: for movies.
PIP (Picture In Picture) button
ON/OFF button: Toggle switches between PIP, POP, sideby-side (aspect) and side-by-side (full). See page 26.
INPUT button: Selects the “picture in picture” input signal.
CHANGE button: Replaces to the main picture and sub
picture.
4 SIZE button
Selects picture size, [FULL], [NORMAL], [WIDE]* and
[ZOOM]. See page 22.
Sub picture
DVI VGA RGB/HV HDMI DVD/HD VIDEO TV for U.S. TV for Europe
5 SOUND button*
6 AUDIO INPUT button*
Selects audio input source [IN1], [IN2], [IN3], [HDMI], [TV]*.
DVI
VGA
RGB/HV
HDMI
DVD/HD
VIDEO
Main picture
Artificial surround sound.
TV for U.S.
TV for Europe
-
-
-
-
-
-
-
-
*: The product you purchased may not have this feature.
English-10
-
-
MTS button*
Multichannel television sound.
SLEEP button
Sets power off timer.
GUIDE button*
Operating Range for the Remote
Control
Point the top of the remote control toward the LCD monitor’s
remote sensor during button operation.
Use the remote control within a distance of about 7 m (23 ft.)
from the front of the LCD monitor’s remote control sensor or
at a horizontal and vertical angle of within 30° within a
distance of about 3.5 m (10 ft.)
Enters on screen program guide (For U.S.).
button*
Activates closed captioning (For U.S.).
Activates Teletext (For Europe).
*: The product you purchased may not have this feature.
Caution:
Important, the remote
control system may
not function when
direct sunlight or strong
illumination strikes the remote control
sensor of the LCD monitor, or when there is
an object in the path.
Handling the remote control
•
Do not subject to strong shock.
•
Do not allow water or other liquid to splash the remote
control. If the remote control gets wet, wipe it dry
immediately.
•
Avoid exposure to heat and steam.
•
Other than to install the batteries, do not open the
remote control.
English-11
English
REMOTE ID button
Activates REMOTE ID function.
Setup
1. Determine the installation location
CAUTION: Installing your LCD display must be done by a
qualified technician. Contact your dealer for
more information.
CAUTION: MOVING OR INSTALLING THE LCD MONITOR
MUST BE DONE BY FOUR OR MORE PEOPLE
(LCD5220), BY TWO OR MORE PEOPLE
(LCD4020/LCD4620). Failure to follow this caution
may result in injury if the LCD monitor falls.
NOTE: If you do not intend to use the Remote Control for a
long period of time, remove the batteries.
3. Connect external equipment
(See pages 14-20)
•
To protect the external equipment; turn off the main
power before making connections.
•
Refer to your equipment user manual for further
information.
4. Connect the supplied power cord
CAUTION: Do not mount or operate the display upside
down, face up, or face down.
CAUTION: This LCD has a temperature sensor and cooling
fan. If the LCD becomes too hot, the cooling fan
will turn on automatically. If the LCD becomes
overheated while the cooling fan is running, a
“Caution” warning will appear. If the “Caution”
warning appears, discontinue use and allow the
unit to cool. Using the cooling fan will reduce the
likelihood of early circuit failure and may help
reduce image degradation and “Image
Persistance”.
If the LCD is used in an enclosed area or if the
LCD panel is covered with a protective screen,
please check the inside temperature of the
monitor by using the “HEAT STATUS” control in
the OSD (see page 27). If the temperature is
higher than the normal operating temperature,
please turn the cooling fan to ON within the FAN
CONTROL menu within the OSD (see page 27).
•
The equipment should be installed close to an easily
accessible power outlet.
•
Please fasten power cord to the LCD monitor by
attaching the screw and clamp.
•
Fully insert the prongs into the power outlet socket.
A loose connection may cause image degradation.
NOTE: Please refer to the “Safety Precautions and
Maintenance” section of this manual for proper
selection of AC power cord.
LCD4020/4620
Screw
Clamp
IMPORTANT: Lay the protective sheet, which was wrapped
around the LCD monitor when it was
packaged, beneath the LCD monitor so as
not to scratch the panel.
2. Install the remote control batteries
Screw hole for clamp
The remote control is powered by two 1.5V AA batteries.
To install or replace batteries:
LCD5220
Screw
Clamp
A. Press and slide to open the cover.
B. Align the batteries according to the (+) and (–)
indications inside the case.
C. Replace the cover.
CAUTION: Incorrect usage of batteries can result in leaks
or bursting.
NEC recommends the following battery use:
•
Place “AA” size batteries matching the (+) and (-) signs
on each battery to the (+) and (-) signs of the battery
compartment.
•
Do not mix battery brands.
•
Do not combine new and old batteries. This can shorten
battery life or cause liquid leakage of batteries.
•
Remove dead batteries immediately to prevent battery
acid from leaking into the battery compartment.
•
Do not touch exposed battery acid, it may injure skin.
English-12
[For LCD5220]
[For LCD4020]
•
Remove the six screws (Figure 8).
•
Remove the six screws (Figure 4).
•
•
Use six of the M4 x 10 screws (included) to attach the
cable cover (Figure 5).
Use six of the M4 x 10 screws (included) to attach the
cable cover (Figure 9).
Figure 4
Figure 8
Figure 9
Figure 5
[For LCD4620]
•
Remove the three screws (Figure 6).
•
Use five of the M4 x 10 screws (included) to attach the
cable cover (Figure 7).
Figure 6
6. Switch on the power of all the attached
external equipment
When connected with a computer, switch on the power of
the computer first.
7. Operate the attached external
equipment
Display the signal from the desired input source.
8. Adjust the sound*
Make volume adjustments when required.
Figure 7
9. Adjust the screen (See pages 24 and 25)
Make adjustments of the screen display position when
necessary.
10. Adjust the image (See page 24)
Make adjustments such as brightness or contrast when
required.
11. Recommended Adjustments
To reduce the risk of the “Image Persistence”, please adjust
the following items based on the application being used:
“SCREEN SAVER”, “SIDE BORDER COLOR” (See page 27)
“DATE & TIME”, “SCHEDULE SETTINGS” (See page 25).
It is recommended that the “FAN CONTROL” setting
(See page 27) be turned to ON also.
*: The product you purchased may not have this feature.
English-13
English
5. Attach the cable cover
Connections
Before making connections:
*
First turn off the power of all the attached equipment and make connections.
*
Refer to the user manual included with each separate piece of equipment.
Wiring Diagram
DVD player
with HDMI out
DVD player with
component out
VCR or
Laser Disc Player
Second monitor
DVD player with
SCART OUT
Computer (Analog)
Computer (Digital)
English-14
Stereo Amplifier
English
Connecting a Personal Computer
Connecting your computer to your LCD monitor will enable you to display your computer’s screen image.
Some video cards and a pixel clock over 162MHz may not display an image correctly.
Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically.
<Factory preset signal timing>
Resolution
640 x 480
800 x 600
1024 x 768
1280 x 768
1360 x 768
1280 x 1024
1600 x 1200
1920 x 1080
Scanning frequency
Horizontal
Vertical
31.5kHz
60Hz
37.9kHz
60Hz
48.4kHz
60Hz
48kHz
60Hz
48kHz
60Hz
64kHz
60Hz
75kHz
60Hz
66.6kHz
60Hz
Remarks
LCD4020/LCD4620
LCD5220
Recommended resolution
Compressed image
Compressed image
Compressed image
Compressed image
Recommended resolution
Connect the LCD Monitor to a Personal Computer
•
To connect the VGA IN connector (mini D-sub 15 pin) on the LCD monitor, use the supplied PC - Video RGB signal cable
(mini D-sub 15 pin to mini D-sub 15 pin).
•
To connect the RGB/HV connector (BNC) on the LCD monitor, use a mini D-sub 15 pin to BNC x 5 signal cable (sold
separately). Select RGB/HV from the INPUT button.
•
When connecting one or more LCD monitors, use the RGB OUT connector (BNC) (BNC INPUT only).
•
AUDIO IN* 1, 2 and 3 can be used for audio input. To select audio source [IN1], [IN2] or [IN3] press the AUDIO INPUT
button.
To RGB/HV IN
BNC INPUT only
BNC x 5
LCD monitor (second monitor)
LCD monitor
BNC x 5
Mini D-sub 15 pin
BNC x 5
To audio output
To analog RGB output
Mini D-sub 15 pin
PC or IBM compatible
*: The product you purchased may not have this feature.
English-15
Connecting to a Macintosh Computer
Connecting your Macintosh computer to your LCD monitor will enable you to display your computer’s screen image. Some
video cards or drivers may not display images correctly.
Connect the LCD Monitor to Macintosh
•
To connect the VGA IN connector (mini D-sub 15 pin) on the LCD monitor, use the supplied PC - Video RGB signal cable
(mini D-sub 15 pin to mini D-sub 15 pin).
•
To connect the RGB/HV IN connector (BNC) on the LCD monitor, use a mini D-sub 15 pin to BNC x 5 signal cable (sold
separately) (BNC INPUT only).
•
If you use with a Macintosh PowerBook, set “Mirroring” to Off.
Refer to your Macintosh’s owner’s manual for more information about your computer’s video output requirements and any
special identification or configuring your monitor’s image and monitor may require.
•
AUDIO IN* 1, 2 and 3 can be used for audio input. To select audio source [IN1], [IN2] or [IN3] press the AUDIO INPUT
button.
To RGB/HV IN
BNC INPUT only
BNC x 5 LCD monitor (second monitor)
LCD monitor
BNC x 5
Mini D-sub 15 pin
BNC x 5
To audio output
To analog RGB output
Mini D-sub 15 pin
Macintosh
*: The product you purchased may not have this feature.
English-16
Connections can be made with equipment that is equipped with a digital interface that complies with the DVI (Digital Visual
Interface) standard.
Connect the LCD Monitor to a Computer with a Digital Output
•
The DVI IN connector also accepts a DVI-D cable.
•
Input TMDS signals conforming to DVI standards.
•
To maintain display quality, use a cable that conforms to DVI standards.
•
AUDIO IN* 1, 2 and 3 can be used for audio input. To select audio source [IN1], [IN2] or [IN3] press the AUDIO INPUT
button.
•
For mode selection, see “DVI MODE” on page 28.
To DVI output
DVI-D connector
To audio output
LCD monitor
DVI-D connector
*: The product you purchased may not have this feature.
English-17
Equipment with a
digital interface such
as a personal
computer with RGB
output (TMDS)
English
Connecting with Digital Interface Equipment
Connecting a DVD Player with component out*
Connecting your DVD player to your LCD monitor will enable you to display DVD video.
Refer to your DVD player user’s manual for more information.
Connect the LCD Monitor to a DVD Player
•
To connect the DVD/HD IN connector (RCA) on the LCD monitor, use an RCA connector cable (sold separately).
Some DVD players may have different connectors such as DVI-D connector.
Select [DVI/HD] mode from the “DVI MODE” menu. For mode selection, see “DVI MODE” on page 28.
RCA
To audio right output
To audio left output
AUDIO IN* 1, 2 and 3 can be used for audio input. To select audio source [IN1], [IN2] or [IN3] press the AUDIO INPUT
button.
To DVD Component video output
To DVI output
DVI-D connector
RCA
LCD monitor
*: The product you purchased may not have this feature.
English-18
Connecting your DVD player to your LCD monitor will enable you to display DVD video.
Refer to your DVD player user’s manual for more information.
Select [HDMI] from the AUDIO INPUT button.
Connect the LCD Monitor to a DVD Player
•
Please use an HDMI cable with HDMI logo.
•
It may take a moment for the signal to appear.
•
PC-DVI signals are not supported.
To HDMI output
LCD monitor
HDMI connector
Connecting a DVD Player with SCART out*
Connecting your DVD player to your LCD monitor will enable you to display SCART.
Connect the LCD Monitor to a DVD Player
•
To connect the DVD/HD IN connector (RCA) on the LCD monitor and connect the video (sync) and the Video In connector
(RCA), use an RCA connector cable (sold separately).
Some DVD players may have different connectors such as DVI-D connector.
Select [ON] mode from the “SCART MODE” menu when you use a SCART connector. For mode selection, see “SCART
MODE” on page 28.
SCART
To audio right output
To audio left output
The AUDIO IN* 1, 2 and 3 can be used for audio input. To select audio source [IN1], [IN2] or [IN3] press the AUDIO INPUT
button.
LCD monitor
RCA
To DVD Component video output
*: The product you purchased may not have this feature.
English-19
English
Connecting a DVD Player with HDMI out*
Connecting to a Stereo Amplifier*
You can connect your stereo amplifier to your LCD monitor. Refer to your amplifier owner’s manual for more information.
Connect the LCD Monitor to a Stereo Amplifier
•
Turn on the LCD monitor and the amplifier only after all connections have been made.
•
Use a stereo Mini-RCA cable to connect the AUDIO OUT* connector (Stereo Mini Jack) on the LCD monitor to the audio
input on the amplifier.
•
Do not reverse the audio left and right jacks.
•
The AUDIO IN* is used for audio input.
•
The AUDIO OUT* jack outputs sound from the selected Audio input.
To audio right output
LCD monitor
To audio left output
VCR or Laser disc player
RCA
To audio right input
Amplifier
To audio left input
External speaker
*: The product you purchased may not have this feature.
English-20
External speaker
English
Basic Operation
Power ON and OFF Modes
The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off.
NOTE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the
Power Button on the front of the LCD.
LCD4020/LCD4620
OFF
Main Power Switch
LCD5220
OFF
Main Power Switch
ON
ON
Power Button
Power Button
Using the remote control
English-21
NORMAL: Displays the aspect ratio the same as it is sent
from the source.
FULL: Fills entire screen.
WIDE*: Expands a 16:9 letter box signal to fill entire screen.
ZOOM (DYNAMIC): Expands a 4:3 pictures to fill the entire
screen with non-linearity. Some of the outside image area
will be cut off due to expansion.
Power Indicator*
Mode
Power ON
Power OFF (Eco Standby)*1
Power consumption under 1W
Power OFF (Standby)
Power consumption under 5W
Power Save
Power Standby when
“SCHEDULE SETTINGS” enabled
Diagnosis (Detecting failure)
Status Indicator Light
Green*2
Red
Amber
Amber Blinking
Green and Amber
blink alternately
Red Blinking
(See Troubleshooting page 38)
*1 When in Eco Standby Mode RS-232C controls do not function.
*2 If “OFF” is selected in POWER INDICATOR (page 27), the LED will not
light when the LCD monitor is in active mode.
ZOOM
The image can be expanded beyond the active display area.
The image which is outside of active display area is not
shown.
ZOOM
Using Power Management
The LCD monitor follows the VESA approved DPM Power
Management function.
The power management function is an energy saving
function that automatically reduces the power consumption
of the display when the keyboard or the mouse has not been
used for a fixed period.
The power management feature on your new display has
been set to the “ON” mode. This allows your display to enter
a Power Saving Mode when no signal is applied. This could
potentially increase the life and decrease the power
consumption of the display.
STANDBY mode is used when the display is connected to
an RS-232C cable or when using the INPUT DETECT
function.
ECO STANDBY uses less power, but the RS-232C and
INPUT DETECT functions are not available.
ZOOM
Picture Mode
DVI,VGA, RGB/HV STANDARD
HDMI*, DVD/HD*,
VIDEO*, TV*
STANDARD
sRGB
HIGHBRIGHT
CINEMA*
HIGHBRIGHT
Information OSD
The Information OSD provides information such as:
Monitor ID, Input Source, Picture Size, etc. Press the
DISPLAY button on the remote to bring up the Information
OSD.
Selecting a video source*
To view a video source:
Use the input button to set [VIDEO].
Use the COLOR SYSTEM menu to set [AUTO], [NTSC],
[PAL], [SECAM], [PAL60], [4.43NTSC], according to your
video format.
Picture Size
1 ID number assigned to current monitor*3
DVI,VGA, RGB/HV
FULL
ZOOM
NORMAL
HDMI*, DVD/HD*,
VIDEO*, TV*
FULL
WIDE*
ZOOM
Aspect ratio
of image
2 ID number assigned monitor to be controlled via RS-232C*4
NORMAL
3 Input Source
4 Audio input mode
Unchanged view*
1
5 Picture size
Recommended selection
for picture size*1
6 Input Signal Information
NORMAL
7 Sub picture information
*3: “IR CONTROL” should be set “Primary” or “Secondary”.
4:3
*4: “IR CONTROL” should be set “Primary”.
ZOOM
(DYNAMIC)
*: The product you purchased may not have this feature.
FULL
Squeeze
WIDE*
Letterbox
*1 Grey areas indicate unused portions of the screen.
English-22
English
OSD (On-Screen-Display) Controls
NOTE: Some functions may not be available depending on the model or optional equipment.
Input source
Main Menu Icons
Main Menu Item
Adjustment Settings
Sub Menu
ADAPTIVE CONTRAST
Select
Goto Adjustment
Return
Close
Key Guide
Press UP or DOWN
button to select
sub-menu.
Press SET.
Press UP or DOWN,
PLUS or MINUS to select
the function or setting to
be adjusted.
Press MENU or EXIT.
Press UP or DOWN
button to select.
Press INPUT button
to decide.
Press UP or DOWN, PLUS
or MINUS button to select.
Press EXIT
Remote Control
Control Panel
LCD4020/4620
LCD5220
OSD screen
English-23
Setting
Default
PICTURE
BRIGHTNESS
Adjusts the overall image and background brightness. Press + or - to adjust.
*1
CONTRAST
Adjusts the image brightness in relationship to the background. Press + or - to adjust.
Note: The sRGB picture mode is standard and cannot be changed.
*2
SHARPNESS
Adjusts the crispness of the image. Press + or - to adjust.
*3
BLACK LEVEL
Adjusts the image brightness in relationship to the background. Press + or - to adjust.
Note: The sRGB picture mode is standard and cannot be changed.
*4
TINT*
Adjusts the tint of the screen. Press + or - to adjust.
*5
Adjusts the color depth of the screen. Press + or - to adjust.
*6
COLOR TEMPERATURE
Adjusts the color temperature of the entire screen. A low color temperature will make the screen
reddish. A high color temperature will make the screen bluish.
Note: The sRGB picture mode is set to a predefined 6500 K standard and cannot be changed.
*7
COLOR CONTROL
Adjusts the levels of the Red, Yellow, Green, Cyan, Blue, Magenta and Saturation.
Note: The sRGB picture mode is standard and cannot be changed.
*8
Select a display gamma for best picture quality.
Note: The sRGB picture mode is standard and cannot be changed.
*9
HDMI, DVD/HD, VIDEO, TV inputs only
COLOR*
HDMI, DVD/HD, VIDEO, TV inputs only
DVI, VGA, RGB/HV, HDMI inputs only
GAMMA SELECTION
NATIVE
Gamma correction is handled by the LCD panel.
2.2
Typical display gamma for use with a PC.
2.4
Good for video (TV, DVD, etc.)
S GAMMA
Special gamma for certain types of movies. Raises the dark parts and lowers the light parts
of the image. (S-Curve)
DICOM SIM.
DICOM GSDF curve simulated for LCD type.
PROGRAMMABLE
A programmable gamma curve can be loaded using NEC software.
ADAPTIVE CONTRAST*
Sets the level of adjustment for dynamic contrast.
*10
HDMI, DVD/HD, VIDEO, TV inputs only
OFF
MID
HIGH
MOVIE SETTINGS*
NOISE REDUCTION
Adjusts the amount of noise reduction. Press + or - to adjust.
6
TV, VIDEO inputs only
FILM MODE
Selects Film mode.
AUTO
HDMI, DVD/HD, VIDEO, TV inputs only
PICTURE RESET
Resets the following settings within the PICTURE menu back to factory setting:
BRIGHTNESS, CONTRAST, SHARPNESS, BLACK LEVEL, TINT, COLOR, COLOR
TEMPERATURE, COLOR CONTROL , GAMMA SELECTION, ADAPTIVE CONTRAST,
MOVIE SETTINGS.
-
Automatically adjusts Screen Size, H position, V position, Clock, Clock Phase, White Level,
and Black Level.
-
VGA, RGB/HV inputs only
AUTO ADJUST
H Position, V Position and Clock Phase are adjusted automatically upon power on.
ADJUST
AUTO SETUP
OFF
VGA, RGB/HV inputs only
H POSITION
Controls the horizontal position of the image within the Display area of the LCD.
Press + to move right. Press - to move left.
-
V POSITION
Controls the vertical position of the image within the Display area of the LCD.
Press + to move up. Press - to move down.
-
CLOCK
Press + to expand the width of the image on the right of the screen.
Press - to narrow the width of the image on the left.
-
VGA, RGB/HV inputs only
*: The product you purchased may not have this feature.
English-24
Adjusts the visual “noise” on the image.
-
Adjusts the horizontal size of the image.
-
Adjusts the vertical size of the image.
-
Select the aspect ratio of the screen image.
-
VGA, RGB/HV, DVD/HD inputs only
H RESOLUTION
DVI, VGA, RGB/HV inputs only
V RESOLUTION
DVI, VGA, RGB/HV inputs only
ZOOM MODE
Does not work with TV input in the U.S.
BASE ZOOM
16:9
CUSTOM
For input sources that have a 16:9 aspect ratio.
HDMI, DVD/HD, VIDEO, TV for Europe inputs only
14:9
For input sources that have a 14:9 aspect ratio.
HDMI, DVD/HD, VIDEO, TV for Europe inputs only
DYNAMIC
Expands 4:3 picture to fill the screen. Some of the image is lost due to expansion.
HDMI, DVD/HD, VIDEO, TV for Europe inputs only
OFF
Selecting “OFF” will display the image in a 1 by 1 pixel format. (If the input resolution is
higher than a 1360 x 768 resolution, the image will be scaled down to fit the screen.)
CUSTOM
Displays an image as large as possible without changing the aspect ration.
ZOOM**
Maintains the aspect ratio while zooming.
1.00
H ZOOM**
Amount of horizontal zoom. Can be adjusted for each BASE ZOOM setting.
1.00
V ZOOM**
Amount of vertical zoom. Can be adjusted for each BASE ZOOM setting.
1.00
H POS**
Horizontal position. Can be adjusted for each BASE ZOOM setting.
0%
V POS**
Vertical position. Can be adjusted for each BASE ZOOM setting.
0%
INPUT RESOLUTION
VGA, RGB/HV inputs only
ADJUST RESET
If there is a problem with signal detection, this function forces the monitor to display the
signal at the desired resolution. After selection, execute “AUTO SETUP” if required.
If no problem is detected, the only available option will be “AUTO”.
Resets the following settings within the ADJUST menu back to factory setting:
AUTO ADJUST, H POSITION, V POSITION, CLOCK, CLOCK PHASE, H RESOLUTION,
V RESOLUTION, ZOOM MODE, INPUT RESOLUTION.
AUTO
-
AUDIO*
BALANCE
CENTER
TREBLE
0
BASS
0
PIP AUDIO
Selects source of PIP audio.
MAIN AUDIO
LINE OUT
Selecting “VARIABLE” will enable to control line out level with VOLUME button.
AUDIO RESET
Resets “AUDIO” options back to factory settings.
FIXED
-
SCHEDULE
OFF TIMER
Sets the monitor to power off after a length of time.
A time between 1 to 24 hours is available.
OFF
SCHEDULE SETTINGS
Creates a working schedule for the monitor to use.
-
SCHEDULE LIST
List of schedules.
-
DATE & TIME
Sets the date, time, and daylight saving region. Date & time must be set in order for the
“SCHEDULE” function to operate.
-
YEAR
-
MONTH
-
DAY
-
TIME
-
DAYLIGHT SAVING
SCHEDULE RESET
OFF
Resets the following settings within the SCHEDULE menu back to factory setting:
OFF TIMER, SCHEDULE SETTINGS.
*: The product you purchased may not have this feature.
**: 16:9, 14:9, CUSTOM only
English-25
English
CLOCK PHASE
PIP
KEEP PIP MODE*
Allows the monitor to remain in “PIP” and “TEXT TICKER” mode after powering off.
When Power is returned, PIP and TEXT TICKER appear without having to enter the OSD.
OFF
PIP MODE*
Picture-in-Picture
OFF
OFF
OFF
PIP
PIP
POP
POP
SIDE BY SIDE (ASPECT) SIDE BY SIDE ASPECT
SIDE BY SIDE (FULL)
PIP SIZE
SIDE BY SIDE FULL
Selects the size of the sub-picture used in Picture-in-Picture (PIP) mode.
LARGE
SMALL
MIDDLE
LARGE
PIP POSITION
Determines where the PIP appears on the screen.
TEXT TICKER*
Allow text insertion within main screen. The TEXT TICKER and PIP functions cannot be used
simultaneouslly. If the PIP function is on, it will be deactivated and vice versa if the
TEXT TICKER is turned on.
PIP RESET
Resets PIP options back to factory settings.
X = 95, Y = 92
OFF
-
OSD
LANGUAGE
Select the language used by the OSD.
ENGLISH
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
SVENSKA
РУССКИЙ
OSD TURN OFF
Turns off the OSD after a period of inactivity. The preset choices are 10-240 seconds.
OSD POSITION
Determines the location where the OSD appears on the screen.
30 Sec.
X = 128, Y = 225
UP
DOWN
LEFT
RIGHT
INFORMATION OSD
Selects whether the information OSD is displayed or not. The information OSD will be
displayed when the input signal or source changes. The information OSD will also give a
warning when there is no-signal or the signal is out-of range.
An interval between 3 to 10 seconds for the Information OSD to appear is available.
MONITOR INFORMATION Monitor Information.
OSD TRANSPARENCY
ON, 3 Sec.
-
Set the transparency level of the OSD.
TYPE2
OFF
TYPE1
TYPE2
OSD RESET
Resets the following settings within the OSD menu back to factory setting:
OSD TURN OFF, OSD POSITION, INFORMATION OSD, OSD TRANSPARENCY.
*: The product you purchased may not have this feature.
English-26
-
MONITOR ID
Sets the monitor ID number from 1-26.
IR CONTROL
Selects the mode of the monitor for use with the infra-red remote control when using the
RS-232C daisy chain.
NORMAL
The monitor will be controlled normally by wireless remote controller.
PRIMARY
Choose “PRIMARY” for the first monitor within an RS-232C daisy chain.
SECONDARY
Choose “SECONDARY” for all subsequent monitors within an RS-232C daisy chain.
LOCK
Prevents the monitor from being controlled by wireless remote controller. To return to normal
operation, press the “DISPLAY” button on the remote controller for 5 seconds.
TILE MATRIX
1
NORMAL
Allows one image to be expanded and displayed over multiple screens (up to 25) through a
distribution amplifier.
H MONITORS
Number of monitors arranged horizontally.
1
V MONITORS
Number of monitors arranged vertically.
1
POSITION
Select which section of the tiled image to be displayed on the monitor.
1
TILE COMP
Turns the TILE COMP feature on.
NO
ENABLE
Enables Tile Matrix.
NO
POWER ON DELAY
Adjusts the delay time between being in “standby” mode and entering “power on” mode.
“POWER ON DELAY” can be set between 0 and 50 seconds.
POWER INDICATOR
Turns ON or OFF the LED located at the front of the monitor.
If “OFF” is selected, LED will not light when the LCD monitor is in active mode.
MULTI DISPLAY RESET
Resets the following settings within the MULTI DISPLAY menu back to factory setting:
MONITOR ID, IR CONTROL, TILE MATRIX, POWER ON DELAY.
0 Sec.
ON
-
DISPLAY PROTECTION
POWER SAVE
All inputs except for TV
Sets how long the monitor waits to go into power save mode after a lost signal.
Note: When connecting DVI, video card might not stop sending digital data even if image has
disappeared. In this case the monitor does not get to power management mode.
STANDBY MODE
Lowers power consumption.
Note: RS-232C Function is lost when in Eco Standby mode.
HEAT STATUS
Displays status of the COOLING FAN, BRIGHTNESS and TEMPERATURE.
FAN CONTROL
Cooling fan reduces the temperature of the display.
SCREEN SAVER
Use the SCREEN SAVER function to reduce the risk of Image Persistence.
ON
STANDBY
AUTO
GAMMA
The display gamma is changed and fixed when “ON” is selected.
OFF
BRIGHTNESS
The brightness is decreased when “ON” is selected.
OFF
MOTION
The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT)
at user determined intervals.
OFF
SIDE BORDER COLOR
Adjusts the color of the side borders when a 4:3 image is displayed.
Press + button, the bar will become lighter.
Press - button, the bar will become darker.
AUTO BRIGHTNESS
Adjusts the brightness level according to the input signal.
15
OFF
DVI, VGA, RGB/HV inputs only
CHANGE SECURITY
PASSWORD
Allows the security password to be changed.
The factory preset password is 0000.
-
SECURITY LOCK
Locks the security password.
DDC/CI
ENABLE/DISABLE: Turns On or OFF the two way communication and control of the monitor.
ENABLE
DISPLAY PROTECTION
RESET
Resets the following settings within the DISPLAY PROTECTION menu back to factory setting:
POWER SAVE, FAN CONTROL, SCREEN SAVER, SIDE BORDER COLOR, AUTO
BRIGHTNESS.
-
OFF
*: The product you purchased may not have this feature.
English-27
English
MULTI DISPLAY
ADVANCED OPTION
INPUT DETECT
All inputs except for TV
Selects the method of input detection the monitor uses when more than two input devices
are connected.
NONE
The Monitor will not search the other video input ports.
FIRST DETECT
When the current video input signal is not present, then the monitor searches for a video signal
from the other video input port. If the video signal is present in the other port, then the monitor
switches the video source input port to the new found video source automatically.
The monitor will not look for other video signals while the current video source is present.
LAST DETECT
When the monitor is displaying a signal from the current source and a new secondary source
is supplied to the monitor, the monitor will automatically switch to the new video source.
When current video input signal is not present, the monitor searches for a video signal from
the other video input port. If the video signal is present in the other port, then the monitor
switches the video source input port to the new found video source automatically.
VIDEO DETECT*
DVD/HD or VIDEO inputs will have priority over DVI, VGA, RGB/HV. When DVD/HD or
VIDEO input signal is present the monitor will change and keep to the DVD/DH or VIDEO
input.
LONG CABLE ON/OFF
Compensates for image degradation caused from using a long cable.
FIRST DETECT
OFF
VGA, RGB/HV inputs only
LONG CABLE MANUAL
Manually compensates for image degradation caused from using a long cable.
VGA, RGB/HV inputs only
RED DELAY
Adjusts the phase of the red signal.
0
GREEN DELAY
Adjusts the phase of the green signal.
0
BLUE DELAY
Adjusts the phase of the blue signal.
0
RED SHARPNESS
Adjusts the performance degradation of the RED signal.
23
GREEN SHARPNESS
Adjusts the performance degradation of the GREEN signal.
23
BLUE SHARPNESS
Adjusts the performance degradation of the BLUE signal.
23
SOG PEAK.
Adjusts the shape of Sync on Green signal.
0
VIDEO EQ.
Optimize the shape (Tailing) of RED, GREEN and BLUE signals.
0
Selects the terminate resistance for matching the cable impedance.
0
RGB/HV input only
SYNC TERMINATE
RGB/HV input only
DVI MODE
Selects the kind of DVI-D equipment which is connected DVI.
Select “DVI-PC” when PC or other computer equipment is connected.
Select “DVI-HD” when DVD player, which has DVI-D output, is connected.
DVI-PC
SCAN CONVERSION
Selects the IP (Interlace to Progressive) conversion function.
Note: For DVI input “DVI-HD” need to be enabled in the DVI mode menu.
PROGRESSIVE
All inputs except VGA, RGB/HV
PROGRESSIVE
Converts interlaced signals to progressive. This is the default setting.
INTERLACE
Disables IP conversion. This setting is best suited for motion pictures, but increases the risk
of image retention.
SCART MODE*
Input mode for devices using SCART connectors.
S-VIDEO MODE*
Selects the S-Video input port function.
PRIORITY
When an S-Video cable is connected to the S-Video input, it will have priority over the
composite input port.
SEPARATE
The S-Video port and Composite port can be selected as independent input ports.
COLOR SYSTEM*
The selected Color System depends on the video format of the input signal.
VIDEO input only
AUTO
Automatically chooses Color System setting based on input signal.
NTSC
PAL
SECAM
4.43NTSC
*: The product you purchased may not have this feature.
English-28
OFF
PRIORITY
AUTO
SCAN MODE*
Some video formats may require different scanning modes in order to best display the image.
OVER SCAN
HDMI, DVD/HD, VIDEO, TV inputs only
OVER SCAN
Image size is larger than what can be displayed. The image edge will appear cropped.
Approximately 95% of the image will be shown on the screen.
UNDER SCAN
Image size stays within the display area. The whole image is displayed on the screen.
ADVANCED OPTION
RESET
Resets the following settings within the ADVANCED OPTION menu back to factory setting:
INPUT DETECT, LONG CABLE ON/OFF, LONG CABLE MANUAL, DVI MODE, SCAN
CONVERSION, S-VIDEO MODE, SCAN MODE.
-
FACTORY RESET
Resets OSD options back to factory settings EXCEPT FOR: CHANGE SECURITY PASSWORD
and SECURITY PASSWORD.
-
*: The product you purchased may not have this feature.
PICTURE MODE
*1: BRIGHTNESS
*2: CONTRAST
*3: SHARPNESS
INPUT: HDMI, DVD/HD, VIDEO, S-VIDEO
HIGHBRIGHT
STANDARD
CINEMA
100
75 (LCD4020/LCD4620)
70 (LCD5220)
80
50
50
50
50 (DVD/HD, HDMI)
50 (DVD/HD, HDMI)
50 (DVD/HD, HDMI)
60 (VIDEO,S-VIDEO) 60 (VIDEO, S-VIDEO) 60 (VIDEO, S-VIDEO)
INPUT: DVI, VGA, RGB/HV
HIGHBRIGHT
STANDARD
sRGB
100
75 (LCD4020/LCD4620)
70 (LCD5220)
100
50
50
-
50
50
50
*4: BLACK LEVEL
50
50
50
50
50
-
*5: TINT
50
50
50
-
-
-
-
-
-
*6: COLOR
*7: COLOR TEMPERATURE
*8: COLOR CONTROL
*9: GAMMA SELECTION
*10: ADAPTIVE CONTRAST
50 (DVD/HD,HDMI)
50 (DVD/HD,HDMI)
50 (DVD/HD,HDMI)
60 (VIDEO,S-VIDEO) 60 (VIDEO,S-VIDEO) 60 (VIDEO,S-VIDEO)
10000K
10000K
10000K
10000K
10000K
-
-
-
-
0 (CENTER)
0 (CENTER)
-
S-GAMMA
2.4
S-GAMMA
NATIVE
NATIVE
-
MID
OFF
OFF
-
-
-
NOTE: When connecting to a TV tuner (For U.S.), refer to page 30.
When connecting to a TV tuner (For Europe), refer to page 32.
English-29
English
PAL-60
Connecting to a TV* (For U.S.)
Initial TV Setup
Before watching TV for the first time it is necessary to
program the channels.
1. Attach the cable or antenna to the coaxial RF Connector
on the side of the monitor.
5. Once channels are in memory, use the CHANNEL EDIT
menu to add or remove channels. Use the CHANNEL
LABELS menu to create unique names for channels, if
desired.
Parental Controls (TV, VIDEO input only)
NOTE: Cable distribution system should be grounded
(earthed) in accordance with ANSI/NFPA 70, the
National Electric Code (NEC), in particular section
820.93, Grounding of Outer Conductive Shield of a
Coaxial Cable.
Parents can block certain types of programming based on
rating and the content.
2. Enter the OSD and go to the TUNER menu below.
2. Enter the password. Default password is 0000. This
password can be changed in the PASSWORD SET
menu.
3. In the TUNING BAND menu select which tuning method
(Air, Cable, Cable HRC, Cable IRC) will be used.
4. Enter the CHANNEL SEARCH menu. Press SET to
automatically scan and store channels to memory.
The channel search will store both analog and digital
channels.
To block programming:
1. Enter the PARENTAL CONTROL menu, found under the
CONFIGURATION submenu within the TUNER OSD.
3. Highlight the square next to the type of programming you
wish to block and press SET on the remote.
NOTE: Analog channels are indicated with a -0 following
the channel number. Digital channels are indicated
with a - followed by a number. For example,
channel 2-0 is analog and channel 2-1 is digital.
Analog channels may also have separate digital
subchannels associated with them. For example
channel 3-0 would be analog followed by channel
3-1, 3-2, etc.
NOTE: Blocking one type of programming will
automatically block all higher rated programming
also. However, it is possible to unlock this
programming while keeping the desired
programming blocked.
TV TUNER
Not all models
have the Digital
Tuner installed.
TUNER
TUNING BAND
Choose AIR or Cable as TV source.
CHECK DTV SIGNAL
Shows the status of the Digital TV signal.
CHANNEL SEARCH
Searches for TV channels and stores them in memory.
ADD ON CHANNEL
SEARCH
Searches for TV channels and stores them in memory without erasing previously stored channels.
FINE TUNING
Performs fine adjustments to analog channels.
CHANNEL EDIT
Add or remove channels stored in memory.
CHANNEL LABELS
Add a label to the channel.
CONFIGURATION
MENU LANGUAGE
TIME ZONE
PASSWORD SET
Set the Parental Control Password. Factory default password is 0000.
PARENTAL CONTROL
PARENTAL
CONTROL MENU
Parents can choose to block types of programming based on rating and content.
ADVANCED
RATING
Downloadable rating, depending on broadcast. Press SET to change setting.
CLOSED CAPTION
OPTIONS
NOTE: Closed captioning settings can not be adjusted for the VIDEO/S-VIDEO inputs.
AUTOMATIC is is the only option available for these inputs.
RESOLUTION
Set the displayed image to the desired resolution.
AUDIO
AUDIO LANGUAGE
Choose the language of audio output.
DIGITAL AUDIO
OUTPUT
Select the digital audio output source. Choose Dolby D/PCM/OFF.
* The product you purchased may not have this feature.
English-30
OFF
No Limitation.
TV-Y
All children. The themes and elements in this program are specifically designed for a very young audience,
including children from ages 2-6.
TV-Y7
Directed to older children. Themes and elements in this program may include mild physical or comic violence
or may frighten children under the age of 7.
TV-G
General audience. It contains little or no violence, no strong language, and little or no suggestive dialogue or
situations.
TV-PG
Parental guidance suggested. The program may contain infrequent coarse language, limited violence, some
suggestive sexual dialogue and situations.
TV-14
Parents strongly cautioned. This program contains some material that many parents would find unsuitable for
children under 14 years of age. This program may contain intense violence (V), intense sexual situations (S),
strong coarse language (L), or intensely suggestive dialogue (D).
TV-MA
Mature audiences only. This program may contain mature themes, indecent language, graphic violence and
explicit sexual content.
Video Parental Guide Ratings Chart
OFF
No Limitation
G
General audiences. All ages are permitted to watch.
PG
Parental guidance suggested. Some material may not be suitable for children.
PG-13
Parents strongly cautioned. Some material may be inappropriate for children under 13.
R
Restricted. Under 17 requires an accompanying parent or adult guardian.
NC-17
No one under 17 permitted to watch.
X
Adults only.
Changing the channel
Both Analog and Digital channels are available using this tuner. In addition to the CH+ and CH- buttons channels can be
changed in the following method.
Tuning Analog Channels
Input the desired channel number using the keypad, then press [SET] or [ENT] to immediately tune to the new channel. If the
number is input and [SET] or [ENT] is not pushed, after a few seconds the channel will be changed. For example to tune to
channel 5, press [5] then press [SET] or [ENT].
Tuning Digital Channels
To tune in to a digital sub-channel enter the number of the main channel, then a dash followed by the number of the subchannel. For example to tune to digital channel 5-1, press [5] then [–] then [1]. Press [SET] or [ENT] to tune.
English-31
English
TV Parental Guide Ratings Chart
Connecting to a TV* (For Europe)
Precautions when connecting the antenna
• Use a coaxial cable which is free from interference. Avoid using a parallel flat wire as interference may occur,
causing the reception to become unstable and noise to appear on the screen.
•
Avoid using an indoor antenna as this may be affected by interference and poor reception.
•
Cable distribution system should be grounded (earthed) in accordance with ANSI/NFPA 70, the National
Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable.
•
Keep the power cord as far away from the antenna wire as possible.
•
Auto Tuning. Please refer to the OSD menu below.
VHF (300-Ohm) antenna / UHF antenna
• When using a 300-ohm twin lead from an outdoor antenna, connect the
VHF or UHF antenna leads to the screws of the VHF or UHF adapter.
Plug the 300-ohm to 75-ohm adapter into the antenna on the LCD MONITOR.
•
When both VHF and UHF antennas are combined: Attach an optional antenna cable signal combiner to the LCD
MONITOR antenna terminal, and connect the cables to the antenna mixer. Consult your local electronics retailer about
available signal combiners.
Reconnect the unit to the power source and turn on the power
• Using the Remote Control or User Controls, select the “TV TUNER”. Select the appropriate menu based upon which
source (cable or antenna) is being used.
•
Refer to the OSD menu below for further information on the “TV TUNER” as well as for information on how to use the
“CHANNEL SEARCH” function to program available channels.
CAUTION:
The screen of the coaxial cable is intended to be connected to earth in the building installation.
TV TUNER
REGION
Selects region.
CHANNEL SEARCH
Automatically stores available channels.
CHANNEL EDIT
Manually adds or removes channels from TV mode.
TELETEXT SELECT
button between TV (VIDEO) picture, TELETEXT or
Press the
MIXED.
TV PICTURE
TELETEXT
MIXED [TV & TELETEXT]
PAGE SELECTION
Use the KEYPAD buttons 0 to 9 to select the required page (3 digit
number).
PAGE UP/DOWN
Press the CH +/- buttons to increase or decrease the page number
selected.
HOLD
Some TELETEXT information is contained in more than one page.
The pages automatically changing after a given reading time.
Press the STILL ON/OFF button to stop the page changing (the
symbol
will appear on the page heading).
Press the STILL ON/OFF button again to allow the page to change
(the symbol
will disappear).
REVEAL
Some TELETEXT pages contain quiz or game questions with
hidden answers.
Press the STILL CAPTURE button to see the answers.
Press the STILL CAPTURE button again to hide the answers.
CANCEL
1. Periodically revised NEWS FLASHES can be obtained from
TELETEXT broadcasts.
Select the News Flash page in TELETEXT mode then press the
PIP ON/OFF button.
You can now watch the TV program and every time the news
flash page is updated it will be automatically displayed in the TV
picture.
Press the PIP ON/OFF button to cause the news flash to
disappear.
2. When a page is selected in TELETEXT mode it may take some
time before it becomes available, pressing the PIP ON/OFF
button will switch to the TV mode.
When the required page is found the page number will appear at
the top of the TV picture, press the PIP ON/OFF button to return
to the selected TELETEXT page.
Note: You cannot change TV program while in this mode.
FAST TEXT (For possible future reference)
The “PICTURE MODE”, “SIZE”, “SOUND” and “AUDIO INPUT”
buttons are used for quick access to color coded pages transmitted
by FAST TEXT broadcast.
RED: PICTURE MODE
GREEN: SIZE
YELLOW: SOUND
CYAN: AUDIO INPUT
INDEX
Press the GUIDE button to select the INDEX page.
* The product you purchased may not have this feature.
English-32
NOTE 1: CREATING A SCHEDULE
English
The schedule function allows the display to be set to power on and off at different times. Up to seven different schedules can be
programmed.
To program the schedule:
1. Enter the SCHEDULE menu. Highlight SCHEDULE SETTINGS using the up and down buttons. Press the SET or the + button to enter the
Settings menu. Highlight the desired schedule number and press set. The box next to the number will turn yellow. The schedule can now
be programmed.
2. Use the up and down arrows to highlight INPUT. Use the + and - buttons to choose the input source.
3. After the INPUT source is selected, use the down button to highlight the hours setting in the ON time slot. Use the + and - buttons to set
the hour. Use the up and down buttons to highlight the minutes setting. Use the + and - buttons to set the minutes. Set the OFF time in the
same manner.
4. Use the down button to select a day on which the schedule will be enabled. Push the
set button to enable. If the schedule is to be ran every day, choose EVERY DAY and
press the SET button. The circle next to EVERY DAY will turn yellow. If a weekly
schedule is desired, choose the days of the week using the up and down buttons and
pressing SET to select. Then highlight the EVERY WEEK option and press SET.
5. After a schedule is programmed the remaining schedules can then be set. Press
MENU to leave the OSD or press EXIT to go back to the previous menu.
DVI
SCHEDULE:
OFF TIMER
SCHEDULE SETTINGS
SCHEDULE LIST
DATE & TIME
SCHEDULE RESET RESET
Note: If schedules are overlapping then the schedule with the highest number will have
priority over the schedule with the lowest number. For example schedule #7 will have
priority over schedule #1.
TODAY:
SETTINGS:
1
2
INPUT:
ON:
OFF:
SEP.27.2006 12:18
3
4
• EVERY DAY
MON TUE
FRI
SAT
EVERY WEEK
Choose
Mark
5
6
7
DVI
10 : 30
17 : 45
WED
SUN
Return
THU
Close
NOTE 2: IMAGE PERSISTENCE
Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image Persistence occurs when a
residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not
permanent, but constant images being displayed for a long period of time should be avoided.
To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the
monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen
saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
Please set “SCREEN SAVER”, “DATE &TIME” and “SCHEDULE SETTINGS” functions to further reduce the risk of Image persistence.
For long life use as Public Display
< Image Sticking of LCD Panel >
When an LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside LCD, and residual
or “ghost” image of previous image may be observed. (Image Persistence)
Image Persistence is not permanent, but when fixed image is displayed for long period, ionic impurities inside LCD are accumulated along
the displayed image, and may be permanent. (Image Sticking)
< Recommendations >
To prevent Image Sticking, and for longer life usage of LCD, the following are recommended.
1. Fixed image should not be displayed for long period. Change fixed images after short intervals.
2. When not in use, please turn off the monitor by remote control, or use Power Management or use Schedule Functions.
3. Lower environmental temperatures prolong the lifespan of the monitor.
When Protective surface (glass, acrylic) is installed over the LCD surface, the LCD surface is located in an enclosed space, the monitor
are stacked, utilize the temperature sensors inside monitor.
To reduce the environmental temperature, use the Cooling Fan, Screen Saver and Low Brightness.
4. Please use “Screen Saver Mode” of monitor.
English-33
Remote Control ID Function
REMOTE CONTROL ID
The remote control included with the display can be used to control up to 26 individual
MultiSync monitors using what is called the REMOTE CONTROL ID mode. The REMOTE
CONTROL ID mode works in conjunction with the Monitor ID, allowing control of up to 26
individual MultiSync monitors. For example: if there are many monitors being used in the
same area, a remote control in normal mode would send signals to every monitor at the
same time Figure 1. Using the remote in REMOTE CONTROL ID mode will only operate
one specific monitor within the group Figure 2.
TO SET REMOTE CONTROL ID
While holding down the REMOTE ID SET button on the remote control, use the KEYPAD
to input the Monitor ID (1-26) of the display to be controlled via remote. The remote can
then be used to operate the monitor having that specific Monitor ID number.
When 0 is selected or when the remote control is in normal mode, all monitors will be
operated.
TO SET/RESET REMOTE CONTROL MODE
ID Mode - To enter ID Mode press the REMOTE ID SET button and hold down for
2 seconds.
Normal Mode - To return to Normal Mode press the REMOTE ID RESET button and hold
down for 2 seconds.
In order for this feature to work properly, the display must be assigned a Monitor ID
number. The Monitor ID number can be assigned under the MULTI DISPLAY menu in the
OSD (See page 27).
Point the remote control towards the remote sensor of the desired monitor and press the
REMOTE ID SET button. The MONITOR ID number is shown on the display when your
remote control is in ID mode.
Monitor ID:1
Monitor ID:2
Monitor ID:3
Remote works
Remote works
Remote works
Figure 1
Remote in
Normal mode or
the REMOTE ID
is set to 0
Monitor ID:1
Monitor ID:2
Monitor ID:3
Remote does
not work
Remote does
not work
Remote works
Figure 2
Remote set up to
use REMOTE
ID:3
Use the remote control to operate a monitor that has a specific MONITOR ID number assigned to it.
1. Set the MONITOR ID number for the display (See page 27). The MONITOR ID number can range from 1-26.
This MONITOR ID number allows the remote control to operate this specific monitor without affecting other monitors.
2. On the remote control, press and hold down the REMOTE ID SET button while using the keypad to input the REMOTE CONTROL ID
number (1-26). The REMOTE ID NUMBER should match the MONITOR ID number of the display to be controlled. Choose “0” to
simultaneously control all displays in range.
3. Point the remote control towards the remote sensor of the desired monitor and press the REMOTE ID SET button.
The MONITOR ID number is shown in red on the display.
If the REMOTE CONTROLID is “0”, then all displays in range will show their respective MONITOR ID number in red.
If the MONITOR ID number is shown in white on the display, the MONITOR ID number and the REMOTE CONTROL ID are not the same.
This LCD monitor can be controlled via personal computer or wireless remote control using an RS-232C connection.
MONITOR ID and IR CONTROL
Using one PC or one infrared wireless controller, up to 26 individual LCD monitors* can be controlled through a daisy chain via RS-232C
connection.
1. Connect PC and LCD monitors*.
Connect a PC’s RS-232C control output to the LCD monitor* RS-232C input. You can then connect the RS-232C output from the LCD
monitor* to another LCD monitor* RS-232C input. Up to 26 monitors can be connected using RS-232C.
2. Set Monitor ID and IR Control mode.
For proper operation, the Monitor ID should be set in the OSD menu of each monitor that is in the chain. The Monitor ID can be set under
the “MULTI DISPLAY” menu in the OSD. The Monitor ID number can be set within a range from 1 to 26. No two monitors should share the
same Monitor ID number. It is recommended to number each monitor in a daisy chain sequentially from 1. The first monitor in the daisy
chain is designated as the primary monitor. Subsequent monitors with the chain are secondary monitors.
In the “ADVANCED OPTION” menu on the first monitor in the RS-232C daisy chain set the “IR CONTROL” to “PRIMARY”.
Set the “IR CONTROL” to “SECONDARY” on all other monitors.
*: MULTEOS M40, MULTEOS M46, MultiSync LCD4020, MultiSync LCD4620, MultiSync LCD5220, MultiSync LCD6520.
English-34
Monitor ID: Displays the ID number of the current monitor within the daisy chain.
Target ID: Displays the ID number of the monitor that to be controlled via daisy chain from the current monitor.
Press the “+” or “-” buttons to change the “Target ID” to show the ID number of the monitor to be controlled. To control the entire daisy
chained monitors simultaneously, select “ALL” as the “Target ID.”
4. Use the wireless remote controller to control the “SECONDARY” monitor while aiming at the “PRIMARY” monitor.
The “MENU OSD” will appear on the selected target monitor.
NOTE:
If the “ID No.” mode select OSD is showing, press the “DISPLAY” button on the remote control while pointing at the “PRIMARY”
monitor to clear this OSD.
HINT:
If you lost control due to the incorrect setting of “IR CONTROL”, pressing the “DISPLAY” button on the remote control for 5 or
more seconds will reset the “IR CONTROL” menu to “NORMAL” function.
English-35
English
3. Press the “DISPLAY” button on the remote control while aiming at the “PRIMARY” monitor. The Information OSD will be shown at
top left side of the screen.
Controlling the LCD monitor via RS-232C Remote Control
This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal.
Functions that can be controlled by a personal computer are:
•
Power ON or OFF
•
Switching between input signals
Connection
LCD Monitor + PC
PC
(Out)
IN
MultiSync
OUT
RS-232C (IN)
MultiSync
RS-232C (OUT)
RS-232C Cable
RS-232C (IN)
RS-232C (OUT)
RS-232C Cable
MultiSync
NOTE: If your PC (IBM or IBM compatible) is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is
required. Contact your dealer for details.
* In order to function, the RS-232C OUT terminal can only be connected to another monitor of the same model.
Do not connect to other types of equipment.
To control monitor or multiple monitors that are daisy-chained together please use the control command. Instructions for the
control command can be found on the CD included with the display. The file is called “External_control.pdf”.
1) Interface
PROTOCOL
RS-232C
BAUD RATE
9600 [bps]
DATA LENGTH
8 [bits]
PARITY BIT
NONE
STOP BIT
1 [bit]
FLOW CONTROL
NONE
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
2) Control command diagram
Please see file “External_Control.pdf” on the CD-ROM.
English-36
Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight
limitations.
Color Control Systems: Allows you to adjust the colors on your screen and customize the color accuracy of your monitor to
a variety of standards.
OmniColor: Combines Six-axis color control and the sRGB standard. Six-axis color control permits color adjustments via six
axes (R, G, B, C, M and Y) rather than through the three axes (R, G and B) previously available. The sRGB standard provides
the monitor with a uniform color profile. This assures that the colors displayed on the monitor are exactly the same as on the
color printout (with sRGB supporting operating system and sRGB printer). This allows you to adjust the colors on your screen
and customise the color accuracy of your monitor to a variety of standards.
sRGB Color Control: A new optimized color management standard which allows for color matching on computer displays
and other peripherals. The sRGB standard, which is based on a calibrated color space, allows for optimal color representation
and backward compatibility with other common color standards.
OSD (On-Screen-Display) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to
use on-screen menus.
Plug and Play: The Microsoft® solution with the Windows® operating system facilitates setup and installation by allowing the
monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically
optimizing display performance.
IPM (Intelligent Power Manager) System: Provides innovative power-saving methods that allow the monitor to shift to a
lower power consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions
and lowering the air conditioning costs of the workplace.
FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size.
VESA Standard (FDMIv1) Mounting Interface: Allows users to connect their LCD monitor to any VESA standard (FDMIv1)
third party mounting arm or bracket. Allows for the monitor to be mounted on a wall or an arm using any third party compliant
device. NEC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America.
DVI-D: The digital-only subset of DVI ratified by the Digital Display Working Group (DDWG) for digital connections between
computers and displays. As a digital-only connector, analog support is not provided for a DVI-D connector. As a DVI-based
digital only connection, only a simple adapter is necessary for compatibility between DVI-D and other DVI-based digital
connectors such as DFP and P&D. The DVI interface of this display supports HDCP.
TILE MATRIX, TILE COMP: Shows one image over multiple screens with accuracy while compensating for bezel width.
ZOOM: Expands image size for horizontal and vertical direction.
RS-232C daisy chain: You can control the multiple monitors by controller or wireless remote controller.
Self-diagnosis: If an internal error should occur, a failure state will be indicated.
CableComp: Automatic long cable compensation prevents image quality degradation (color shift and dull signals) caused by
long cable lengths.
English-37
English
Features
Troubleshooting
No picture
• The signal cable should be completely connected to the
display card/computer.
•
The display card should be completely seated in its slot.
•
Front Power Switch and computer power switch should
be in the ON position.
•
Check to make sure that a supported mode has been
selected on the display card or system being used.
(Please consult display card or system manual to
change graphics mode.)
RED LED on monitor is blinking
• A certain failure might have occurred, please contact
your nearest authorized NEC DISPLAY SOLUTIONS
service facility.
Display image is not sized properly
• Use the OSD Image Adjust controls to increase or
decrease the coarse adjustment.
•
•
Check the monitor and your display card with respect to
compatibility and recommended settings.
•
Check the signal cable connector for bent or pushed-in
pins.
Power Button does not respond
• Unplug the power cord of the monitor from the AC outlet
to turn off and reset the monitor.
Image persistence
• Please be aware that LCD Technology may experience a
phenomenon known as Image Persistence. Image
Persistence occurs when a residual or “ghost” image of a
previous image remains visible on the screen. Unlike
CRT monitors, LCD monitors’ image persistence is not
permanent, but constant images being displayed for a
long period of time should be avoided. To alleviate image
persistence, turn off the monitor for as long as the
previous image was displayed. For example, if an image
was on the monitor for one hour and a residual image
remains, the monitor should be turned off for one hour to
erase the image.
NOTE: As with all personal display devices, NEC DISPLAY
SOLUTIONS recommends displaying moving
images and using a moving screen saver at regular
intervals whenever the screen is idle or turning off
the monitor when not in use.
Check to make sure that a supported mode has been
selected on the display card or system being used.
(Please consult display card or system manual to
change graphics mode.)
Selected resolution is not displayed properly
• Use OSD Display Mode to enter Information menu and
confirm that the appropriate resolution has been
selected. If not, select corresponding option.
No Sound
• Check to see if speaker cable is properly connected.
•
Check to see if mute is activated.
•
Check to see if volume is set at minimum.
Remote Control is not available
• Check the Remote Control’s batteries status.
•
Check if batteries are inserted correctly.
•
Check if the Remote Control is pointing at the monitor’s
remote sensor.
•
Check the Remote Control Mode status.
•
The remote control system may not function when direct
sunlight or strong illumination strikes the remote control
sensor of the LCD monitor, or when there is an object in
the path.
“SCHEDULE”/“OFF TIMER” function is not working
properly
• The “SCHEDULE” function will be disabled when the
“OFF TIMER” is set.
•
Image is unstable, unfocused or swimming is apparent
• Signal cable should be completely attached to the
computer.
If the “OFF TIMER” function is enabled and the power to
the LCD monitor is turned off when the power supply is
interrupted unexpectedly, then the “OFF TIMER” will be
reset.
•
Use the OSD Image Adjust controls to focus and adjust
display by increasing or decreasing the fine adjustment.
When the display mode is changed, the OSD Image
Adjust settings may need to be re-adjusted.
Snowy Picture, Poor Sound in TV
• Check antenna/cable connection. Use new cable if
necessary.
•
Check the monitor and your display card with respect to
compatibility and recommended signal timings.
•
If your text is garbled, change the video mode to noninterlace and use 60Hz refresh rate.
Interference in TV
• Check components for shielding, move away from
monitor if necessary.
Image of component signal is greenish
• Check to see if the DVD/HD input connector is selected.
Inactive area
• There is a 5 mm inactive area between the bezel and the
LCD panel. As a result, a gap is visible on the LCD panel
between the bezel and the actual picture.
LED on monitor is not lit
(no green or red color can be seen)
• Power Switch should be in the ON position and power
cord should be connected.
•
Make certain the computer is not in a power-saving
mode (touch the keyboard or mouse).
Inactive area
Either light vertical or horizontal stripes may appear, depending on the specific display pattern. This is no product fault or
degradation.
English-38
Product Specifications
LCD Module
Pixel Pitch:
Resolution:
Color:
Brightness:
Contrast Ratio:
Viewing Angle:
Design View Distance:
Frequency
Horizontal:
Vertical:
40" /101.6 cm diagonal
0.648 mm
1366 x 768 dots
Over 16 million colors (depending on video card used)
700 cd/m2 (Max.), 500 cd/m2 (Typ.)
2000:1
89° (typ) @ CR>10
1100 mm
15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)
31.5 kHz - 91.1 kHz (Digital Input)
50.0 - 85.0 Hz
Pixel Clock
25.2 MHz - 162.0 MHz
Viewable Size
885.168 x 497.664 mm
Input Signal
DVI
DVI-D 24pin
Digital RGB
DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080*1 (60Hz)
VGA
15pin Mini D-sub
Analog RGB
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080*1 (60Hz)
Sync
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
Analog RGB
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080*1 (60Hz)
Sync
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
RGB/HV
BNC (R,G,B,H,V)
HDMI*2
HDMI Connector
Digital RGB
HDMI
1080p*1, 1080i*1, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz
DVD/HD*2
RCA (Y, Cb/Pb, Cr/Pr)
Component
Y : 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr) : 0.7 Vp-p/75 ohm
HDTV/DVD:1080p*1, 1080i*1, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz
VIDEO*2
BNC
RCA
Composite
1.0 Vp-p/75 ohm
NTSC/PAL/SECAM/4.43NTSC/PAL60
S-VIDEO*2
Mini DIN 4 pin
S-VIDEO
Y: 1.0 Vp-p/75 ohm C: 0.286 Vp-p/75 ohm (NTSC), 0.3 Vp-p/75 ohm (PAL/SECAM)
NTSC/PAL/SECAM/4.43NTSC/PAL60
RGB/HV
BNC (R,G,B,H,V)
Analog RGB
0.7 Vp-p with 75 ohm terminated
Separate HV sync: TTL level (Posi / Nega)
VIDEO*2
BNC
Composite
1.0 Vp-p with 75 ohm terminated
AUDIO
Input
RCA (L/R) X2
STEREO Mini Jack
Analog Audio
Stereo L/R 0.5 Vrms
HDMI Connector
Digital Audio
PCM 32, 44.1, 48 KHz (16/20/24bit)
AUDIO
Output
STEREO Mini Jack
Analog Audio
Stereo L/R 0.5 Vrms
Output Signal
AUDIO*2
Speaker Output
External Speaker Jack 15 W + 15 W (8 ohm)
Control
RS-232C In:
RS-232C Out:
TV*2
Antenna:
Channel Coverage:
Power Supply
9 Pin D-sub
9 Pin D-sub (with daisy chain)
For U.S
F-connector Impedance 75 ohm
VHF: 2 - 13 ch
UHF: 14 - 69 ch
CATV: 1 - 130 ch
ATSC (8VSB): 2 - 69 ch
64/256 QAM : 1 - 135 ch
For Europe
F-connector Impedance 75 ohm
VHF: E2 to E12/R1 to R12
UHF: E21 to E69
CATV: S1 to S41
3.0 - 1.2 A @ 100-240VAC, 50/60Hz
Operational Environment
Temperature:
Humidity:
Altitude:
5 - 40°C (Default brightness), 5 - 20°C (Max brightness)
20 - 80% (without condensation)
0 - 3000 m
Storage Environment
Temperature:
Humidity:
-20 - 60°C
10 - 90% (without condensation)/ 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension
Net:
Gross:
919.7 (W) x 532.2 (H) x 140 (D) mm (without stand)
1147 (W) x 761 (H) x 312 (D) mm
Weight
Net:
Gross:
29.4 Kg (Without stand)
38.9 Kg
VESA compatible arm mounting interface
3 x 200 mm x 200 mm (8 Holes)
2 x 200 mm x 200 mm (6 Holes)
Complied Regulatory and Guidelines
UL60950-1/CSA C22.2 No.60950-1/ TUV-GS/EN60950-1/NOM
FCC- B/DOC-B/EN55022-B/EN55024/EN61000-3-2/EN61000-3-3/CE/GOST-R
Power Management
VESA DPM
Plug & Play
VESA DDC2B, DDC/CI
Accessories
User’s manual, Power Cord, Video Signal Cable, Remote Control, AA Battery x 2, Clamp x 3,
Screw x 9, CD-ROM, Thumbscrew for stand x 2, Cable cover
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image
English-39
*2: The product you purchased may not have this feature.
English
Specifications - LCD4020
Specifications - LCD4620
Product Specifications
LCD Module
Pixel Pitch:
Resolution:
Color:
Brightness:
Contrast Ratio:
Viewing Angle:
Design View Distance:
Frequency
Horizontal:
Vertical:
46" /116.8 cm diagonal
0.648 mm
1366 x 768 dots
Over 16 million colors (depending on video card used)
650 cd/m2 (Max.), 500 cd/m2 (Typ.)
2000:1
89° (typ) @ CR>10
1300 mm
15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)
31.5 kHz - 91.1 kHz (Digital Input)
50.0 - 85.0 Hz
Pixel Clock
25.2 MHz - 162.0 MHz
Viewable Size
1018.353 x 572.54 mm
Input Signal
DVI
DVI-D 24pin
Digital RGB
DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080*1 (60Hz)
VGA
15pin Mini D-sub
Analog RGB
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080*1 (60Hz)
Sync
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
Analog RGB
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080*1 (60Hz)
Sync
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
RGB/HV
BNC (R,G,B,H,V)
HDMI*2
HDMI Connector
Digital RGB
HDMI
1080p*1, 1080i*1, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz
DVD/HD*2
RCA (Y, Cb/Pb, Cr/Pr)
Component
Y : 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr) : 0.7 Vp-p/75 ohm
HDTV/DVD:1080p*1, 1080i*1, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz
VIDEO*2
BNC
RCA
Composite
1.0 Vp-p/75 ohm
NTSC/PAL/SECAM/4.43NTSC/PAL60
S-VIDEO*2
Mini DIN 4 pin
S-VIDEO
Y: 1.0 Vp-p/75 ohm C: 0.286 Vp-p/75 ohm (NTSC), 0.3 Vp-p/75 ohm (PAL/SECAM)
NTSC/PAL/SECAM/4.43NTSC/PAL60
RGB/HV
BNC (R,G,B,H,V)
Analog RGB
0.7 Vp-p with 75 ohm terminated
Separate HV sync: TTL level (Posi / Nega)
VIDEO*2
BNC
Composite
1.0 Vp-p with 75 ohm terminated
AUDIO
Input
RCA (L/R) X2
STEREO Mini Jack
Analog Audio
Stereo L/R 0.5 Vrms
HDMI Connector
Digital Audio
PCM 32, 44.1, 48 KHz (16/20/24bit)
AUDIO
Output
STEREO Mini Jack
Analog Audio
Stereo L/R 0.5 Vrms
Output Signal
AUDIO*2
Speaker Output
External Speaker Jack 15 W + 15 W (8 ohm)
Control
RS-232C In:
RS-232C Out:
TV*2
Antenna:
Channel Coverage:
Power Supply
9 Pin D-sub
9 Pin D-sub (with daisy chain)
For U.S
F-connector Impedance 75 ohm
VHF: 2 - 13 ch
UHF: 14 - 69 ch
CATV: 1 - 130 ch
ATSC (8VSB): 2 - 69 ch
64/256 QAM : 1 - 135 ch
For Europe
F-connector Impedance 75 ohm
VHF: E2 to E12/R1 to R12
UHF: E21 to E69
CATV: S1 to S41
3.4 - 1.35 A @ 100-240VAC, 50/60Hz
Operational Environment
Temperature:
Humidity:
Altitude:
5 - 40°C (Default brightness), 5 - 20°C (Max brightness)
20 - 80% (without condensation)
0 - 3000 m
Storage Environment
Temperature:
Humidity:
-20 - 60°C
10 - 90% (without condensation)/ 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension
Net:
Gross:
1055.4 (W) x 608.6 (H) x 140 (D) mm (without stand)
1278 (W) x 837 (H) x 312 (D) mm
Weight
Net:
Gross:
36.1 Kg (Without stand)
47.1 Kg
VESA compatible arm mounting interface
3 x 200 mm x 200 mm (8 Holes)
2 x 200 mm x 200 mm (6 Holes)
Complied Regulatory and Guidelines
UL60950-1/CSA C22.2 No.60950-1/ TUV-GS/EN60950-1/NOM
FCC-B/DOC-B/EN55022-B/EN55024/EN61000-3-2/EN61000-3-3/CE/GOST-R
Power Management
VESA DPM
Plug & Play
VESA DDC2B, DDC/CI
Accessories
User’s manual, Power Cord, Video Signal Cable, Remote Control, AA Battery x 2, Clamp x 3,
Screw x 9, CD-ROM, Thumbscrew for stand x 2, Cable cover
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image
English-40
*2: The product you purchased may not have this feature.
Product Specifications
LCD Module
Pixel Pitch:
Resolution:
Color:
Brightness:
Contrast Ratio:
Viewing Angle:
Design View Distance:
Frequency
Horizontal:
Vertical:
52" /132.1 cm diagonal
0.6 mm
1920 x 1080 dots
Over 16 million colors (depending on video card used)
700 cd/m2 (Max.), 500 cd/m2 (Typ.)
2000:1
89° (typ) @ CR>10
1400 mm
15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)
31.5 kHz - 91.1 kHz (Digital Input)
50.0 - 85.0 Hz
Pixel Clock
25.2 MHz - 162.0 MHz
Viewable Size
1192 x 688 mm
Input Signal
DVI
DVI-D 24pin
Digital RGB
DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
VGA
15pin Mini D-sub
Analog RGB
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
Sync
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
Analog RGB
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
Sync
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
RGB/HV
BNC (R,G,B,H,V)
HDMI*2
HDMI Connector
Digital RGB
HDMI
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz
DVD/HD*2
RCA (Y, Cb/Pb, Cr/Pr)
Component
Y : 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr) : 0.7 Vp-p/75 ohm
HDTV/DVD:1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz
VIDEO*2
BNC
RCA
Composite
1.0 Vp-p/75 ohm
NTSC/PAL/SECAM/4.43NTSC/PAL60
S-VIDEO*2
Mini DIN 4 pin
S-VIDEO
Y: 1.0 Vp-p/75 ohm C: 0.286 Vp-p/75 ohm (NTSC), 0.3 Vp-p/75 ohm (PAL/SECAM)
NTSC/PAL/SECAM/4.43NTSC/PAL60
RGB/HV
BNC (R,G,B,H,V)
Analog RGB
0.7 Vp-p with 75 ohm terminated
Separate HV sync: TTL level (Posi / Nega)
VIDEO*2
BNC
Composite
1.0 Vp-p with 75 ohm terminated
AUDIO
Input
RCA (L/R) X2
STEREO Mini Jack
Analog Audio
Stereo L/R 0.5 Vrms
HDMI Connector
Digital Audio
PCM 32, 44.1, 48 KHz (16/20/24bit)
AUDIO
Output
STEREO Mini Jack
Analog Audio
Stereo L/R 0.5 Vrms
Output Signal
AUDIO*2
Speaker Output
External Speaker Jack 15 W + 15 W (8 ohm)
Control
RS-232C In:
RS-232C Out:
TV*2
Antenna:
Channel Coverage:
Power Supply
9 Pin D-sub
9 Pin D-sub (with daisy chain)
For U.S
F-connector Impedance 75 ohm
VHF: 2 - 13 ch
UHF: 14 - 69 ch
CATV: 1 - 130 ch
ATSC (8VSB): 2 - 69 ch
64/256 QAM : 1 - 135 ch
For Europe
F-connector Impedance 75 ohm
VHF: E2 to E12/R1 to R12
UHF: E21 to E69
CATV: S1 to S41
4.7 - 1.9 A @ 100-240VAC, 50/60Hz
Operational Environment
Temperature:
Humidity:
Altitude:
5 - 40°C (Default brightness), 5 - 20°C (Max brightness)
20 - 80% (without condensation)
0 - 3000 m
Storage Environment
Temperature:
Humidity:
-20 - 60°C
10 - 90% (without condensation)/ 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension
Net:
Gross:
1200 (W) x 696 (H) x 147.5 (D) mm (without stand)
1481 (W) x 926 (H) x 334 (D) mm
Weight
Net:
Gross:
44.3 Kg (Without stand)
55.5 Kg
VESA compatible arm mounting interface
2 x 200 mm x 2 x 200 mm (8 Holes)
Complied Regulatory and Guidelines
UL60950-1/CSA C22.2 No.60950-1/ TUV-GS/EN60950-1
FCC-B/DOC-B/EN55022-B/EN55024/EN61000-3-2/EN61000-3-3/CE/GOST-R
Power Management
VESA DPM
Plug & Play
VESA DDC2B, DDC/CI
Accessories
User’s manual, Power Cord, Video Signal Cable, Remote Control, AA Battery x 2, Clamp x 3,
Screw x 9, CD-ROM, Thumbscrew for stand x 2, Cable cover
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image
English-41
*2: The product you purchased may not have this feature.
English
Specifications - LCD5220
Pin Assignment
1) Analog RGB input (MiniDsub15p): VGA
Pin No
Name
1
Video Signal Red
2
Video Signal Green
3
Video Signal Blue
4
GND
Mini D-SUB 15P
1
5
DDC-GND
6
Red-GND
7
Green-GND
8
Blue-GND
9
+5V (DDC)
10
SYNC-GND
11
GND
12
DDC-SDA
13
H-SYNC
14
V-SYNC
15
DDC-SCL
5
6
10
11
15
2) S-VIDEO input: VIDEO
Pin No
Name
1
GND
2
GND
3
Y (Luminance)
4
C (Chroma)
3) Digital RGB input (DVI-D): DVI
Pin - Assignment of DVI connector:
1
TX2-
9
TX1-
17
2
TX2+
3
Shield (TX2 / TX4)
10
TX1+
18
TX0+
11
Shield (TX1 / TX3)
19
Shield (TX0 / TX5)
4
NC
12
NC
20
NC
5
NC
13
NC
21
NC
6
DDC-Serial Clock
14
+5V power
22
Shield (TXC)
7
DDC-Serial Data
15
Ground
23
TXC+
8
NC
16
Hot plug detect
24
TXC-
8
TX0-
1
16
9
24
17
4) RS-232C input/output
Pin No
Name
1
connected to 7&8
2
RXD
3
TXD
4
connected to 6
5
GND
6
connected to 4
7
connected to 1&8
8
connected to 1&7
9
NC
D-SUB 9P
1
6
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
English-42
5
9
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s
top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentallyfriendly products, and always strive to help define and comply with the latest independent standards from agencies such as
ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).
Disposing of your old NEC product
The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of
material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely
disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling
procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end
of its life.
All required information concerning the disposal of the product and country-specific information on recycling facilities can be
found on our following websites:
http://www.nec-display-solutions.com/greencompany/ (in Europe),
http://www.nec-display.com (in Japan) or
http://www.necdisplay.com (in USA).
Energy Saving
This monitor features an advanced energy saving capability. When a VESA Display Power Management Signalling (DPMS)
Standard signal is sent to the monitor, the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.
Mode
Power consumption
LED color
Normal Operation
Approx. 300W (LCD4020)
Approx. 340W (LCD4620)
Approx. 420W (LCD5220)
Green
Energy Saving Mode
Less than 5W
Amber Blinking
Power Off
Less than 5W
Amber
Off Mode (Eco standby)
Less than 1W
Red
WEEE Mark (European Directive 2002/96/EC)
Within the European Union
EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic
products carrying the mark (left) must be disposed of separately from normal household waste. This includes
monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your
NEC display products, please follow the guidance of your local authority, or ask the shop where you
purchased the product, or if applicable, follow any agreements made between yourself and NEC.
The mark on electrical and electronic products only applies to the current European Union Member States.
Outside the European Union
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local
authority so as to comply with the correct disposal method.
English-43
English
Manufacturer’s Recycling and Energy Information
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising