Lorex | L114V251 | Instruction manual | Lorex L114V251 digital video recorder

Lorex L114V251 digital video recorder
DIGITAL VIDEO
SURVEILLANCE RECORDER
WITH MOTION DETECTION AND AUDIO RECORDING
INSTRUCTION MANUAL
English Version 2.0
MODEL:
L114V SERIES
www.lorexcctv.com
Copyright © 2008 Lorex Technology Inc.
Thank you for purchasing the L114 Digital Video Surveillance Recorder. Lorex is committed
to providing our customers with a high quality, reliable security product.
The L114 series offers excellent performance at a value price. This small form (9x12x2")
surveillance DVR provides real time recording in quad mode and single channel, as well as
audio recording and motion detection. The L114 also has a remote control and password
protection.
To learn more about the DVR, and to learn about our complete range of accessory products,
please visit our website at:
www.lorexcctv.com
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RICK OF ELECTRIC SHOCK DO
NOT REMOVE COVER. NO USER SERVICABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the products ' enclosure that may be of
sufficient magnitude to constitute a risk of electric shock
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF THE PLUG TO THE WIDE SLOT AND FULLY
INSERT.
Important Safeguards
Important Safeguards
In addition to the careful attention devoted to quality standards in the manufacture process of your video
product, safety is a major factor in the design of every instrument. However, safety is your responsibility too.
This sheet lists important information that will help to assure your enjoyment and proper use of the video
product and accessory equipment. Please read them carefully before operating and using your video product.
Installation
1. Read and Follow Instructions - All the safety and
operating instructions should be read before the
video product is operated. Follow all operating
instructions.
2. Retain Instructions - The safety and operating
instructions should be retained for future reference.
3. Heed Warnings - Comply with all warnings on the
video product and in the operating instructions.
4. Polarization - Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other.
A grounding type plug has two blades
and a third grounding prong.
The wide blade or the third prong are
provided for your safety.
If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet
5. .Power Sources - This video product should be
operated only from the type of power source
indicated on the marking label. If you are not sure of
the type of power supply to your location, consult
your video dealer or local power company. For video
products intended to operate from battery power, or
other sources, refer to the operating instructions.
6. Overloading - Do not overload wall outlets of
extension cords as this can result in the risk of fire
or electric shock. Overloaded AC outlets, extension
cords, frayed power cords, damaged or cracked wire
insulation, and broken plugs are dangerous. They
may result in a shock or fire hazard. Periodically
examine the cord, and if its appearance indicates
damage or deteriorated insulation, have it replaced
by your service technician.
7. Power-Cord Protection - Power supply cords should
be routed so that they are not likely to be walked on
or pinched by items placed upon or against them,
paying particular attention to cords at plugs,
convenience receptacles, and the point where they
exit from the video product.
8.
Ventilation - Slots and openings in the case are
provided for ventilation to ensure reliable operation
of the video product and to protect it from
overheating. These openings must not be blocked
or covered. The openings should never be blocked
by placing the video equipment on a bed, sofa, rug,
or other similar surface. This video product should
never be placed near or over a radiator or heat
register. This video product should not be placed in
a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the video
product manufacturer’s instructions have been
followed.
9. Attachments - Do not use attachments unless
recommended by the video product manufacturer as
they may cause a hazard.
10. Water and Moisture - Do not use this video product
near water. For example, near a bath tub, wash bowl,
kitchen sink or laundry tub, in a wet basement, near
a swimming pool and the like.
Caution: Maintain electrical safety. Powerline
operated equipment or accessories connected to
this unit should bear the UL listing mark of CSA
certification mark on the accessory itself and should
not be modified so as to defeat the safety features.
This will help avoid any potential hazard from
electrical shock or fire. If in doubt, contact qualified
service personnel.
11. Accessories - Do not place this video equipment
on an unstable cart, stand, tripod, or table. The video
equipment may fall, causing
serious damage to the video
product. Use this video product
only with a cart, stand, tripod,
bracket, or table recommended by
the manufacturer or sold with the
video product. Any mounting of the
product
should
follow
the
manufacturer’s instructions and
use a mounting accessory recommended by the
manufacturer.
iii
Important Safeguards
Service
Use
13. Servicing - Do not attempt to service this video
equipment yourself as opening or removing covers
may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service
personnel.
19. Cleaning - Unplug the video product from the wall
outlet before cleaning. Do not use liquid cleaners or
aerosol cleaners. Use a damp cloth for cleaning.
14. Conditions Requiring Service - Unplug this video
product from the wall outlet and refer servicing to
qualified service personnel under the following
conditions.
A. When the power supply cord or plug is
damaged.
B. If liquid has been spilled or objects have fallen
into the video product.
C. If the video product has been exposed to rain
or water.
D. If the video product does not operate normally
by following the operating instructions. Adjust
only those controls that are covered by the
operating instructions. Improper adjustment of
other controls may result in damage and will often
require extensive work by a qualified technician
to restore the video product to its normal
operation.
E. If the video product has been dropped or the
cabinet has been damaged.
F. When the video product exhibits a distinct
change in performance. This indicates a need for
service.
15. Replacement Parts - When replacement parts are
required, have the service technician verify that the
replacements used have the same safety
characteristics as the original parts. Use of
replacements specified by the video product
manufacturer can prevent fire, electric shock or other
hazards.
16. Safety Check - Upon completion of any service or
repairs to this video product, ask the service
technician to perform safety checks recommended
by the manufacturer to determine that the video
product is in safe operating condition.
17. Wall or Ceiling Mounting - The cameras provided
with this system should be mounted to a wall or
ceiling only as instructed in this guide, using the
provided mounting brackets.
18. Heat - The product should be situated away from
heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that
produce heat.
iv
20. Product and Cart Combination - Video and cart
combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may
cause the video product and car combination to
overturn.
21. Object and Liquid Entry - Never push objects for
any kind into this video product through openings as
they may touch dangerous voltage points or
“short-out” parts that could result in a fire or electric
shock. Never spill liquid of any kind on the video
product.
22. Lightning - For added protection for this video
product during a lightning storm, or when it is left
unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the
antenna or cable system. This will prevent damage
to the video product due to lightning and power line
surges.
General Precautions
General Precautions
1. All warnings and instructions of this manual should be followed.
2. Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents. Use a
water dampened cloth for cleaning.
3. Do not use this unit in humid or wet places.
4. Keep enough space around the unit for ventilation. Slots and openings in the storage cabinet
should not be blocked.
5. During lightning storms, or when the unit is not used for a long time, disconnect the power
supply, antenna, and cables to protect the unit from electrical surge.
FCC CLASS B NOTICE
Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not in-stalled and used in accordance with the instruction, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception (which can be determined by turning the equipment
on and off), the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or an experienced radio or television technician for assistance
This equipment has been certified and found to comply with the limits regulated by FCC, EMC,
and LVD. Therefore, it is designated to provide reasonable protection against interference and will
not cause interference with other appliance usage.
However, it is imperative that the user follows this manuals guideline to avoid improper usage
which may result in damage to the unit, electrical shock and fire hazard injury
In order to improve the feature functions and quality of this product, the specifications are subject
to change without notice from time to time.
www.lorexcctv.com
v
Features
Features
• Simultaneous Recording and Playback
• Up to 60 fps recording speed
• Backup to USB flash drive
• Adjustable screen position
• Quad and single channel recording
• NTSC / PAL
• MJPEG video compression
• Motion Detection with Adjustable Time Duration
• Date / Time search
• Power Recovery and Auto-Restore Record Mode
• Audio Recording
vi
Table of Contents
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Basic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Connect the Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Connect the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Connect the Power Adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Menu Navigation Tips & Tricks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Installing Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installation Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Assembling the Camera Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connecting BNC Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Camera Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Starting the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Display Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Auto Sequence Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Logging in to the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Entering Your Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Setting the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Motion Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Manual Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Recording Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Searching for Recorded Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Time Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Event List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Covert Channel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Motion Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Hard Disk Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Password Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Time Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Event List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Loss Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
vii
F/W Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Load Setup Default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
USB Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Event List (System Menu) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Using USB Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Using Lorex Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Launching Lorex Client . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Playing Saved Video Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Playback Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Sub-Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Exporting to AVI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
32
33
34
Appendix 1: System Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Appendix 2: Full Connectivity Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Appendix 3: Using Listen-in Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Appendix 4: Replacing the Hard Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Removing the Hard Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Replacing the Hard Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Formatting the Hard Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Appendix 5: Compression Codecs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
viii
Getting Started
Getting Started
The system comes with the following components:
1 X DVR
1 X REMOTE CONTROL
1 X POWER ADAPTOR
1 X POWER CABLE
INSTRUCTION MANUAL,
QUICK START GUIDE, AND
SOFTWARE CD
HARD DRIVE SIZE, NUMBER OF CHANNELS, AND CAMERA CONFIGURATION MAY VARY
BY MODEL. PLEASE REFER TO YOUR PACKAGE FOR SPECIFIC CONTENT DETAILS.
CHECK YOUR PACKAGE TO CONFIRM THAT YOU HAVE RECEIVED THE COMPLETE
SYSTEM, INCLUDING ALL COMPONENTS SHOWN ABOVE.
1
Basic Setup
Basic Setup
1. Connect the Cameras
a. Connect up to four BNC cameras to the BNC
(female) ports on the rear panel of the system.
2. Connect the Monitor
a. Connect the VGA cable from your monitor to the
VGA port on the rear panel of the system.
Figure 1.0 Connect up to four BNC cameras
3. Connect the Power Adaptor
a. Connect the power cable to the power adaptor.
b. Connect the power cable to the DC12V port on
the rear panel of the system.
c. Connect the power adaptor to a wall outlet.
Optional
You can connect line-in audio (RCA) from an audio
capable camera or microphone (not included). Use the
audio-out port (RCA) to connect speakers (not included).
Figure 1.1 Connect a VGA monitor
LINE IN AUDIO /
AUDIO CAPABLE CAMERA
(not included)
AUDIO OUT /
SPEAKERS
(not included)
2
Figure 1.2 Connect the power cable
Front Panel
Front Panel
1
2
3
4
5
7
8
9
10
6
11
12
1. USB 2.0 port: Connect a USB flash drive for backup.
2. Up / CH 1: In menus, move cursor up; during live viewing, view channel 1 in full-screen.
3. Down / CH 2: In menus, move cursor down; during live viewing, view channel 2 in
full-screen.
4. Right / CH 3: In menus, move cursor right; during live viewing, view channel 3 in full-screen.
5. Left/ CH 4: In menus, move cursor left; during live viewing, view channel 4 in full-screen.
6. Menu: Press to open system Menu; closes/exits options/menus.
7. Play/Pause: During live viewing, press to open the Event List and select a recorded event;
during playback, press to play/pause video.
8. Rew/Mute: During playback, press to increase reverse playback speed (2X, 4X, 8X); in Live
Mode, press to Mute/Unmute audio; in menus, press to enter/confirm selections.
9. FF/Sequence: During playback, press to increase forward playback speed (2X, 4X, 8X);
during live viewing, press to start/stop Auto-Sequence mode (system displays each channel
in full-screen in sequence).
10. Record/Stop: During playback, press to stop playback; during live viewing, press to start/
stop manual recording (recording Schedule must be disabled).
11. IR Receiver: Receives infrared signal from the remote control.
12. Power / HDD Indicators: LED indicator for system power: when system is powered on, LED
is red; LED indicator for internal hard disk: when in continuous recording mode, LED pulses
green.
3
11
Rear Panel
Rear Panel
1
2
3
4
5
6
1. XGA: Port to connect a VGA (VGA or XVGA output) monitor (not included).
2. Video Out: BNC (female) port to connect the system to a DVR or observation system.
3. Video In: BNC (female) inputs for cameras 1~4.
4. Audio In: RCA (female) port for audio recording (audio capable cameras or microphone).
5. Audio Out: RCA (female) port to connect the system to external speakers, a DVR, or an
observation system
6. DC 12V: Power port for the included power adaptor.
4
Remote Control
Remote Control
The remote control is the primary input method for
navigating the user interface of the system.
1. CH 1~4: During live viewing, press to view
cameras 1~4 in single channel full-screen; press 4
to return to quad split-screen; during USB Backup,
1=Start Time, 2=End Time, 3=N/A, 4=Start backup.
2.
: Press to move cursor UP when navigating
menus or while in Search mode.
3.
: Press to move cursor DOWN when navigating
menus or while in Search mode.
4.
/+: During playback, press to increase reverse
6
1
playback speed (2X, 4X, 8X); press to mute/
unmute volume to a connect audio output device; in
the Event List, press to switch pages.
5.
6.
/-: During playback, press to increase forward
playback speed (2X, 4X, 8X); in the Event List,
press to switch pages.
2
7
3
8
4
9
5
/„: Start/stop manual recording—recording
schedule must be disabled.
7. MENU: Press to open system menu; closes/exits
options/menus; during playback, press to open
USB Backup menu.
Figure 3.0 Remote Control
8. ENTER: Confirm menu selections; during playback of saved video.
9.
/: During playback, press to play/pause video; during live viewing, press to open the Event
List; in the Event List, press to playback selected file.
Menu Navigation Tips & Tricks
When navigating the system menus with the remote control, the following buttons are most
commonly used on the remote control:
• 1
•
•
2
3
4
: Move cursor UP
•
/
: Move cursor DOWN
•
: Confirm selection
: Move cursor RIGHT
•
: Close/exit options/menus.
/
/-
/
/+
/
: Move cursor LEFT
ATTENTION: This manual refers to basic navigation (up, down, left, right) as
can use buttons 1~4 and the
buttons for basic navigation.
. You
5
Installing Cameras
Installing Cameras
Before you install the camera, carefully plan where and how it will be positioned, and where you
will route the cable that connects the camera to the DVR or observation system.
Installation Warning
• Select a location for the camera that provides a clear view of the area you want to monitor, which
is free from dust, and is not in line-of-sight to a strong light source or direct sunlight.
• Plan the cables' route so that it is not close to power or telephone lines, transformers, microwave
ovens or other electrical equipment that could interfere with the DVR.
• Select a location for the camera that has an ambient temperature between 14°F~113°F
(-10°C~45°C).
• If you plan to install the camera in a location that has conditions not recommended in this manual,
consult with a professional installer and consider use of a separate camera cover or housing.
• Before starting permanent installation, have another person hold the camera for you while you
verify its performance by observing the image on a monitor.
Assembling the Camera Stand
To assemble the camera stand:
1. Attach the pedestal to the ceiling, wall,
or other surface by the base using the
provided screws.
2. Attach the camera to the pedestal.
Adjust the angle of the camera, and
tighten the thumbscrew to set the
position.
Note: You can attach the camera to the
stand using the screw point on the top or
the bottom of the camera (to maintain
proper camera alignment). This prevents
the image from becoming inverted.
Figure 4.0 Attach camera to base
6
Installing Cameras
Connecting BNC Cameras
Use a BNC/Power extension cable (not
included) to connect your BNC cameras to a
monitor, DVR, or observation system and
power source.
To connect the extension cable:
1. Connect the extension cable to the
camera:
• Connect the BNC cable to the camera.
• Connect the power cable (male) to the
camera.
2. Connect the extension cable to the DVR/
monitor/observation system:
Figure 5.0 Male and female ends of BNC/Power extension cable
• Connect the BNC cable to BNC port (female) on the DVR.
• Connect the power cable to a power adaptor.
ATTENTION - The ends of the extension cable are NOT THE SAME: one end has a male
connector and the other end has a female connector. Before permanaently running the
cable, make sure you have oriented the extension cable correctly between the camera and
the DVR, monitor, or observation system.
Power cable—male: Connect the male
power cable to the camera.
Power cable—female: Connect the
female power cable to the power adaptor.
Camera Connections
Figure 5.1 Full connectivity diagram
7
Starting the System
Starting the System
To power the system On/Off:
• Connect the power cable to the DC 12V port on the rear panel of the system
Note: Make sure all cameras and cables are properly connected prior to powering on the system.
At startup, the system performs a basic system check and runs an initial loading sequence. After
a few moments, the system loads a live Quad split-screen display view—Live Viewing: you can
also view in full-screen single channel. See “Display Modes” on page 9.
Camera Title, Status Icons, and Date / Time bar appear on the On-Screen Display.
1
CH1
CH2
CH3
CH4
5
2
3
2008/11/20 10:32:30
4
6
Figure 6.0 Live viewing with on-screen display
1. Camera Title: CH1~4 appears in the top-left corner of each channel.
2. Main Display: Displays both full-screen single channel and Quad split-screen.
3. Status Icons: Status icons for Motion recording and Video Loss.
4. Motion Alarm Icon: Icon for triggered motion alarm.
5. Recording Icon: Shown during active recording (manual and scheduled recording).
6. Date / Time:Year/month/day and hour/minute/second appear in a black bar in the bottom-left corner of
the main display screen.
8
Starting the System
On-Screen Display
The following makeup the on-screen display of the system:
•
Recording: Indicates active recording on each channel (manual and scheduled
recording).
•
Motion: Indicates motion recording or motion detected on active channel.
•
Motion Alarm: Indicates motion has been detected on active channel.
Note: Sensitivity and Alarm Duration must be enabled for the selected channel.
•
Video Loss: Indicates that a camera is not connected or has been disconnected.
• Date / Time bar: The date appears as yyyy/mm/dd; the time appears as hh/mm/ss.
Note: You cannot change the date and time format.
2008/11/20 10:32:30
Display Modes
The system can display channels in full-screen single channel and quad split-screen. It also
features an Auto Sequence Mode, where all four channels are displayed in sequence in
full-screen.
Note: By default, the system loads the quad split-screen at startup.
To change display modes:
1. Press buttons 1
full-screen.
2. Press the
4
2
3
4
on the remote control to view each respective channel in
button to return to Quad split-screen.
CH1
CH1
CH3
2008/11/20 10:32:30
Single Channel Full-Screen
CH2
CH4
2008/11/20 10:32:30
Quad Split-Screen
Figure 6.1 Display modes
9
Starting the System
Auto Sequence Mode
In Auto Sequence Mode, the system automatically switches between full-screen channels 1~4 in
sequence.
CH1
AUTO
2008/11/20 10:32:30
CH4
AUTO
CH2
2008/11/20 10:32:30
AUTO
2008/11/20 10:32:30
CH3
AUTO
2008/11/20 10:32:30
Figure 6.2 Auto Sequence Mode
To enable/disable Auto Sequence Mode:
1. Press the
button on the front panel. "AUTO" appears in the bottom-right corner of the
main display screen; the system begins displaying full-screen channels in sequence.
Note: Auto Sequence can be started in both full-screen single channel and quad split-screen
modes.
2. Press the
button again to stop Auto Sequence Mode. By default, the system returns to
quad split-screen mode.
You can customize the dwell time for Auto Sequence mode. For more details, see “Screen” on
page 23.
10
Logging in to the System
Logging in to the System
You must login to the system with a 6-character password every time you access the system
Setup Menu.
ATTENTION: The default system password is 111111
Entering Your Password
If your press the
screen will appear.
button on the front panel or
on the remote control, the password
To enter your password:
1. Press the following buttons on the remote control to move the cursor and input selections:
• 1
•
•
2
3
/
: Move cursor UP
•
/
: Move cursor DOWN
•
/
/-
/
/+
: Move cursor LEFT
: Confirm selection
: Move cursor RIGHT
2. Select Shift and press
3. Select
4
+ and press
to change to uppercase characters and symbols.
to delete/backspace.
4. When finished, select Enter and press
.
For more details on changing your password, see “Password Change” on page 25.
11
Setting the Date and Time
Setting the Date and Time
It is highly recommended to immediately set the date and time when first setting up your system.
To set the date and time:
1. Click
to open the Setup Menu. Login with your system password (by default, 111111).
2. Select System and press
3. Select Time Set and press
.
. The Time Set menu appears.
Figure 6.3 Time Set screen
4. Under Time Set, press
to select the date and time (yyyy/mm/dd and hh/mm/ss)
and press
to change values.
5. Press
and then select Apply and press
6. Press
repeatedly to exit all menus.
12
. The new time is saved.
Recording
Recording
By default, the system is set to immediately record video from connected cameras in continuous
Time Record Mode.
The system automatically records and saves events in 4-hour blocks. Active recording is indicated
by the red Record Icon in the top-right corner of each channel.
CH1
CH2
CH3
2008/11/20 10:32:30
Figure 7.0 Recording on all four channels
Motion Recording
You can configure the system to only record when motion is detected on selected cameras.
Motion Recording is indicated by the green Motion Icon in the top-right corner of the channel.
You can configure both Time Recording and Motion Recording in the Record Schedule in the
Setup Menu. See “Record” on page 21.
Manual Recording
/„
Press
on the remote control or press
on all four channels.
on the front panel to start/stop manual recording
Note: "No Recording" must be selected in the Record Schedule in order to use manual
recording. See “Record” on page 21.
Recording Audio
The system can record one audio channels. You must have audio enabled cameras or
microphones connected to the system in order to use this function.
13
Playback
Playback
View recorded video on the system through playback mode.
CH1
2008/11/20 10:32:30
Figure 8.0 Playback display view
To begin playback:
1. Press
/
. The Event List opens. For more details, see “Event List” on page 17.
Figure 8.1 Event List
2. Press
to select a record event from the list (press
Playback begins for the selected event.
Note: Please allow a few seconds for the event file to load.
3. During playback, you have access to the following:
14
to turn pages) and press
/
.
Playback
•
•
•
/
/+
/-
: Press to pause playback; press again to resume playback
: Click to increase reverse playback speed (2X, 4X, 8X).
: Click to increase forward playback speed (2X, 4X, 8X).
CH1
2008/11/20 10:32:30
Figure 8.2 Icons for 8X reverse playback
4. Press
/„
to stop playback.
During playback, you can select start/stop times for a selected clip and backup the data to a USB
flash drive (not included). For more details on USB Backup, see “USB Backup” on page 27.
15
Searching for Recorded Video
Searching for Recorded Video
You can search for recorded video on the system using Time Search or the Event List.
Time Search
Use Time Search to manually select a time for the system to search for record video.
To use Time Search:
1. Press
to open the Setup Menu. Login with your system password (by default, 111111).
2. From the Setup Menu, select Search and press
. The Time Search menu opens.
Figure 9.0 Time Search menu
to select the date and time (yyyy/mm/dd and hh/mm/ss) and press
to change values.
3. Press
4. Press
/
. Playback begins for the selected time.
Note: Please allow a few moments for the system to search for the requested data.
5. During playback, you have access to the following:
•
•
•
/
/+
/-
6. Press
16
: Press to pause playback; press again to resume playback
: Click to increase reverse playback speed (2X, 4X, 8X).
: Click to increase forward playback speed (2X, 4X, 8X
/„
to stop playback.
Searching for Recorded Video
Event List
You can also search for recorded video data by using the Event List.
Note: The Event List contains events which have occured over the last 4 hours.
Event List
3
1
2
068 08/12/17 12:07:00 MOT OXXX
067 08/12/17 12:06:33 TIME
066 08/12/17 12:05:46 REC START
065 08/12/17 12:05:40 MOT OXXX
064 08/12/17 12:03:17 MOT OXXX
063 08/12/17 12:03:12 MOT OXXX
062 08/12/17 12:02:48 MOT OXXX
061 08/12/17 12:01:12 MOT OXXX
060 08/12/17 12:00:00 MOT OXXX
059 08/12/17 11:59:34 MOT OXXX
PAGE (01/07)
4
5
6
Figure 9.1 Event List
1. Event Number: The system tags each event with a number; the highest number indicates the most
recent event.
2. Date: The date the event occured (yy/mm/dd).
3. Time: The time the event occured (hh/mm/ss).
4. Message: System messages for particular instances:
• REC START: Recording started on the system
• REC STOP: Recording stopped on the system.
• TIME: time changed on system’s internal clock (the system saves a 4-hour block for each recorded
event).
• POWER ON: The system has been powered on.
5. MOT Status: Motion status for channels 1~4. 0 = motion detection enabled; X = motion detetction
disabled.
6. Page: There are ten events for page; press
to turn pages in the Event List.
17
Searching for Recorded Video
To use the Event List:
1. Press
/
2. Press
. The Event List opens.
to select a record event from the list (press
to turn pages) and press
/
.
Playback begins for the selected event.
Note: Please allow a few seconds for the event file to load.
3. During playback, you have access to the following:
•
•
•
/
/+
/-
: Press to pause playback; press again to resume playback
: Click to increase reverse playback speed (2X, 4X, 8X).
: Click to increase forward playback speed (2X, 4X, 8X).
CH1
2008/11/20 10:32:30
Figure 9.2 Playback from Event List
4. Press
/„
to stop playback.
During playback (from Time Search or from the Event List), you can select start/stop times for a
selected clip and backup the data to a USB flash drive (not included). For more details on USB
Backup, see “USB Backup” on page 27.
18
Using the Setup Menu
Using the Setup Menu
The Setup menu allows you to configure various settings on the system, including date/time,
camera settings, and motion detection.
To open the Setup menu:
• Press
. You must login with your system password (by default, 111111).
Figure 10.0 Setup Menu
The Setup Menu contains the following options:
• Camera
• Record
• Motion Detection
• Screen
• Audio
• System
TIP!
• Search
• Exit
When navigating menus:
• Press
• Press
to select options.
or
to confirm
selections.
19
Using the Setup Menu
Camera
Covert Channel Display
Configure settings for each camera and
enable/disable display on the main display
screen (covert display).
You can turn off a channel from the main
display screen from the system Main Menu.
Use this function as a covert camera display.
CH1
CH2
CH3
Figure 11.0 Camera menu
2008/11/20 10:32:30
To configure camera settings:
Figure 11.1 Diabled/covert camera display
1. From the Setup Menu, select Camera and
press
. The Camera menu opens.
2. Under Channel, press
camera 1, 2, 3, or 4.
to select
1. From the Camera menu, select Channel
to channel 1~4.
and press
2. Select Display and press
On/Off.
3. Select the following options and press
to increase/decrease the sliders:
3. Press
• Brightness
• Contrast
• Hue
• Saturation
4. Press
To enable/disable covert camera display:
to select
until the Exit menu appears.
Select Save & Exit and press
to
save your settings. The disabled channel
will appear black.
until the Exit menu appears.
Select Save & Exit and press
save your settings.
to
TIP!
If your monitor is in a public
viewing area, use the disable
display feature for covert
recording. The system will
continue to record from the
connected camera, but the
display on the monitor gives
the appearance that a camera
is not connected
20
Using the Setup Menu
Record
• Event Rec Duration:
Set record speed, quality, record schedule and
recording duration for triggered events.
Event Record Duration is the length of
time the system will record when motion
is detected on a selected camera. Set
from 5, 10, 15, 20, 25, or 30 seconds (by
default, 10 seconds).
• Record Schedule:
Press
to select each hour from
to set the record
0~23. Press
method (Red=Time/Continuous
Recording, Green=Motion Recording,
Grey=No recording).
Figure 12.0 Record Menu
Note: In order to use Manual Recording,
you must apply "No Recording" to a selected
hour block in the record Schedule.
To configure record settings:
1. From the Setup Menu, select Record and
press
. The Record menu opens.
2. Select the following options and press
to configure settings:
• Record Speed:
Select channels 1~4 and press
to
set the frames per second (FPS) for
each channel. NTSC: by default, 15 fps;
max. 60 fps. PAL: by default, 12 fps,
max. 50 fps.
Figure 12.2 Record Schedule
3. Press
until the Exit menu appears.
Select Save & Exit and press
save your settings.
to
Figure 12.1 Record Speed menu
• Record Quality:
Set as Normal, High, or Highest.
21
Using the Setup Menu
Motion Detection
Motion Area
Configure settings for motion sensitivity,
motion grid, and the motion alarm for channels
1~4.
Motion Area allows you set the specific area of
the channel for motion detection. This can be
useful in both high traffic and static areas.
ATTENTION: The Motion Area can only be
set using the buttons on the front panel.
CH3
Motion Area
Figure 13.0 Motion Detection Setup menu
To apply motion detection:
1. From the Setup Menu, select Motion
(CH1, CH2, CH3, CH4) MOVE
(MUTE, SELECT) SET (MENU) EXIT
. The Motion
Detection and press
Detection Setup menu opens.
2. Select Channel, and press
channels 1~4.
to select
3. Select Sensitivity and press
to select
1~4, or Off (1=lowest sensitivity, 4=highest
sensitivity).
4. Select Alarm Duration and press
select 5, 10, 15, 20, 25, 30, CONT
(continuous), or Off.
to
until the Exit menu appears.
Select Save & Exit and press
save your settings.
to
Note: Sensitivity and Alarm Duration must
be enabled in order to see the Alarm icon
when motion is detected on a selected
channel.
22
Figure 13.1 Motion Area
To configure the motion area:
1. From the Setup Menu, select Motion
. The Motion
Detection and press
Detection Setup menu opens.
2. Select Motion Area and press
Note: Alarm Duration enables a buzzer to
accompany motion detection. Set the time
(in seconds) for the buzzer to sound when
motion is detected on a selected camera.
5. Press
2008/11/20 10:32:30
3. Press
to move the cursor to a
desired area. Press
4. Press
to set the cursor.
to apply the blue motion
area. When finished, press
5. Press
.
to set.
until the Exit menu appears.
Select Save & Exit and press
save your settings.
to
Using the Setup Menu
Screen
Audio
Use the Screen menu to set resolutions, turn
the channel border on/off, adjust the main
display position, and set the dwell time for Auto
Sequence Mode..
Use the Audio menu to enable/disable audio
recording, change audio input/output volume,
and enable/disable mute.
Figure 15.0 Audio menu
Figure 14.0 Screen menu
To configure audio settings:
To configure screen settings:
1. From the Setup Menu, select Audio and
1. From the Setup Menu, select Screen and
press
press
. The Screen menu opens.
2. Select Border and press
to select
On/Off. If On, a white border appears in
Quad mode dividing the quadrants of the
main display screen.
3. Select Video Adjustment and press
.
The menu disappears. Press
to
adjust the vertical and horizontal position
of the main display.
4. Select Auto Switching and press
to
set the dwell time for Auto Sequence
mode from 1~10 seconds or Off. The
higher the time, the longer the single
channel will remain on-screen during Auto
Sequence mode.
5. Select Resolution and press
to set
the display resolution at 640x480,
800x600, 1024x768 (default), or
1280x1024.
6. Press
. The Audio menu opens.
2. Select Record and press
audio recording On/Off.
to turn
Note: If audio recording is enabled, you
must connect line-in audio (RCA) to the
Audio-In port on the rear panel of the
system.
3. Select Mute and press
to Mute On/
Off. If off, all audio on the system will be
disabled (input and output).
4. Select Input Volume and press
increase/decrease the slider.
to
5. Select Output Volume and press
increase/decrease the slider.
6. Press
to
until the Exit menu appears.
Select Save & Exit and press
save your settings.
to
until the Exit menu appears.
Select Save & Exit and press
save your settings.
to
23
Using the Setup Menu
System
Overwrite Enable
Use the Sytem menu to configure the internal
hard drive, change your password, set the
date/time, view the event list, enable/disable
the video loss alarm, and upgrade system
firmware.
• From the Hard Disk Setup menu, select
to
Overwrite Enable and press
select Yes or No.
Note: If Yes, the system will overwrite the
oldest recorded video data on the hard drive
once the hard drive is full (the system stores
the last 4 hours of any recorded event). If
No, the system will prompt you that the hard
drive is full and will stop recording.
Format HDD
Use Hard Disk Setup to format the internal
hard drive.
Figure 16.0 System menu
To configure system settings:
• From the Setup Menu, select System and
press
. The System menu opens.
Note: You must stop recording before
attempting to format the hard drive.
ATTENTION: Formatting erases all
recorded video data on the hard drive.
Formatting cannot be undone.
System settings are not affected by
fornatting.
Hard Disk Setup
The Hard Disk Setup menu displays the size of
the internal hard drive (Disk 0) and amount of
drive space currently consumed (in MB).
To format the hard drive:
1. Select Format HDD and press
.
Note: If you have not already stopped
recording, you will be prompted to press
CH4( ) to stop recording prior to
formatting.
Figure 16.1 Hard Disk Setup menu
Use Hard Disk Setup to enable/disable disk
overwrite.
24
2. Enter your 6-character system
password. The system begins formatting
the hard drive. This could take several
moments depending on the size of your
system’s hard drive.
Once formatting is complete, the system will
return to Live Mode.
Using the Setup Menu
Event List
Password Change
Use Hard Disk Setup to change your system
password (by default, 111111).
You can access the Event List from the System
menu. For more details on using the Event List,
see “Event List” on page 17.
Loss Alarm
Enable/disable the buzzer when a camera is
disconnected.
To enable/disable the loss alarm:
1. From the System menu, select Loss
Alarm and press
to select On/Off.
Figure 16.2 Password Change screen
To change your system password:
1. From the Hard Disk Setup menu, select
Password Change and press
.
2. Enter your current password.
Note: Enter your new 6-character
password. Select Shift to view uppercase
characters and symbols.
3. Re-enter your new 6-character password
to confirm. The password screen closes
and returns you to the System menu.
4. Press
Note: If On, a short buzzer will sound if a
camera is disconnected; the loss icon will
also appear in the top-right corner of the
affected channel. If Off, the buzzer will not
sound, but the loss icon will appear in the
top-right corner of the affected channel.
F/W Upgrade
Firmware upgrades can provide improved
functionality to your system. You can download
these free upgrades from www.lorexcctv.com
Note: You must disable recording on the
system prior to updating the firmware.
until the Exit menu appears.
Select Save & Exit and press
save your settings.
to
ATTENTION: You must save your
settings from the Exit menu for your new
password to take effect.
Figure 16.3 Firmware upgrade screen
Time Set
You should always set the date and time when
first starting up the system. For details on
setting the time, see “Setting the Date and
Time” on page 12.
To upgrade firmware:
1. Download the update from
www.lorexcctv.com to your PC. The
firmware carries the file extension, .FWI
25
Using the Setup Menu
2. Connect a USB flash drive to your PC.
Copy the .FWI file to the connect USB
flash drive.
3. Connect the USB flash drive to the USB
port on the front panel of the system
Exit
Use the Exit menu to save changes to system
settings and load factory defaults.
4. Open the Setup menu. Login with your
system password (by default 111111).
5. From the Setup menu select System and
.
press
Note: The current firmware version appears
under F/W Update in the System menu.
6. Select F/W Update and press
.
Figure 16.4 Exit menu
To open the Exit menu and save your changes:
Note: If you have not already stopped
recording, the system will prompt you to
press 4 to stop recording.
/
7. Press
to start the firmware update.
The screen closes and the system
updates the firmware automatically.
Please allow 3 minutes for the update to
take place.
ATTENTION: DO NOT operate the
system or remove the USB flash drive
while the update is in progress.
1. From any open system menu, press
until the Exit menu appears.
OR
1. From the System menu, select Exit and
press
.
2. Select Save & Exit and press
save your settings.
to
Load Setup Default
You can restore your system to factory settings
from the Exit menu.
To load factory settings:
1. From the Main Menu, select System and
8. Disconnect and then re-connect the power
cable from the rear panel to reset the
system. Remove the USB flash drive. The
new firmware version should appear in the
top-left corner of the initial loading screen.
Search
You can search for recorded video on your
system according to a specific time. For more
details on using Time Search, see “Searching
for Recorded Video” on page 16.
26
press
. The System menu opens.
2. Select Exit and press
.
3. From the Exit menu, select Load Setup
. The system
Default and press
immediately begins restoring the system to
factory settings.
USB Backup
USB Backup
2. Select a file and press
You can backup recorded video data from the
system to a USB flash drive (not included). You
can access USB Backup through direct
Playback, or through Search and Event List in
the system menus.
Note: You must connect a USB flash drive
to the USB port on the front panel in order
to use USB Backup.
Playback
/
button to open the Event
List.
2. Select a file and press
/
to begin
playback.
3. Press
opens.
to begin
playback.
3. Press
opens.
. The USB Backup screen
Using USB Backup
To use USB Backup:
1. Connect a USB flash drive to the USB port
on the front panel.
To open USB Backup:
1. Press the
/
. The USB Backup screen
2. Begin Playback through direct Playback,
Search, or the Event List.
3. During playback, press
Backup screen opens.
. The USB
4. Press 1 to set a Start Time. You can
pause/play video, and increase/decrease
playback speeds.
5. Press 2 to set a Stop Time. The size of
the backup file appears.
OR
Search
1. Open the Setup menu. Login with your
system password (by default, 111111).
2. Select Search and press
. The Time
6. Press 4 to start backup. The system
scans the USB flash drive.
Note: If there is not enough space on the
USB flash drive, the following message will
appear: "CAPACITY IS NOT ENOUGH."
Search screen opens.
3. Enter a Start and End Time and press
/
to begin playback.
7. Press 4 again to copy data to the USB
flash drive. The system displays the
estimated time remainng for file transfer.
8. Once the system displays the message
4. Press
opens.
. The USB Backup screen
"COMPLETE, press
Backup menu.
OR
Event List (System Menu)
/„
to exit the
Note: Copied video files are saved as .VVF
files.
1. Open the System Menu, select Event List
and press
.
27
USB Backup
Lorex Client Software
The system comes with the Lorex Client application that lets you playback video files you have
saved to a USB flash drive (not included)..
Figure 17.0 DVR Viewer main window
System Requirements
Prior to using Lorex Client, make sure your PC meets or exceeds the following system
requirements:
Description
Requirement
CPU
Pentium™ 4 or above
Operating
System
Windows XP/Vista
Memory
512 MB RAM
Video
16 MB of video memory
28
Using Lorex Client
Using Lorex Client
Prior to using Lorex Client, make sure you have copied video data from the system to a USB flash
drive (not included).
Launching Lorex Client
To open DVR Viewer:
1. Insert the software CD included with your system into your PC’s CD-ROM or DVD-R/RW
drive.
2. Double-click the file, VVF Player.exe. DVR Viewer opens.
Note: You can also copy this file to your PC.
1
2
4
5
6
3
Figure 18.0 Lorex Client main screen
1. Main Display Screen: Displays video in single channel and Quad mode.
2. Display Information: Shows playback speed and date/stamp.
3. Control Buttons: Primary control buttons include the following:
•
•
•
: Click to open a saved video file (.VVF).
: Increase reverse playback speed (2X,
4X, 8X).
: Rewind one frame and pause.
•
: Click to pause playback.
•
: Advance one frame and pause.
•
: Click to start forward playback.
•
: Increase forward playback (2X, 4X, 8X).
4. Volume: Volume slider.
Note: Line-in audio required during original recording in order to hear volume during playback.
5. Playback Slider: Move the playback slider to jump forward or backward in the video file.
29
Using Lorex Client
6. Still Capture & View mode buttons: Snapshot & View buttons include the following:
•
: Click to take a screenshot of the DVR Viewer display screen—copy the image to MS Paint,
Photoshop or another imaging application.
•
: Click to view in full-screen single channel.
•
: Click to view in Quad split-screen.
Playing Saved Video Files
Use Lorex Client to playback saved/backed up video files copied from the system a USB flash
drive.
To playback saved files:
1. Connect a USB flash drive with saved video data to your PC.
2. Launch Lorex Client.
3. Click
. In the new window, select the .VVF file and click Open. The file immediately begins playing
(at 1X speed) in DVR Viewer.
Note: You can also right-click anywhere on the DVR Viewer main window and select Open
file... or press F2 on your keyboard.
Playback Options
During playback, you have access to the following options:
Playback control buttons: Click any of the buttons along
the bottom of the DVR Viewer main window to increase/
decrease forward and reverse playback, pause, and play
video frame-by-frame.
Change Display Mode On-the-Fly: From the DVR Viewer main window (by default, Quad
split-screen mode), double click channels 1~4 to view the respective channel in single-channel.
Double-click again to return to Quad mode.
Note: You can also click a channel in Quad mode and then click
Click
to return to Quad mode.
to view it in single-channel.
Playback Slider: Click and drag the slider to jump forward or backward in the file.
30
Using Lorex Client
Sub-Menu
The sub-menu lets you access several options.
Figure 18.1 Lorex Client sub menu
To open the sub-menu:
1. Right-click anywhere on the main window to open the sub-menu. The sub-menu includes the
following:
• Open File: Select to open a .VVF file
• Audio: Volume up/down; Mute on/off.
• Open Disk: Select to view data from a
connected hard drive previously installed in
a DVR system (hard drive must be set as
slave).
• Full-Screen: View Lorex Client channel display
in full screen (controls hidden).
• Export: Select to convert the .VVF file to an
.AVI file. AVI files are compatible with media
players such a VLC and DiVx.
• Show Time: Show/hide the time from all
channels during playback.
• Always On Top: Keep the Lorex Client window
on top of other application windows.
• Playback: Open the playback menu (same
playback options as on the main window).
• Capture: Add markers to save a portion of the
saved video as a .VVF file. See “Capture”
on page 32.
• Maximize: View Lorex Client main window in
large window (controls along bottom of
window).
• Aspect Ratio: Set the screen size as either
640x448 or 640x544.
• Split-Mode: Set the display mode to Split 1
(single channel) or Split 4 (Quad
split-screen).
• Options: Select to open the Lorex Client
options menu. See “Options” on page 34.
• About Viewer: View application infomation for
Lorex Client.
• Exit: Close Lorex Client.
31
Using Lorex Client
Capture
Use the capture feature to save a portion of
video from the original VVF file.
To capture video:
1. Open Lorex Client. Open a saved video
file.
2. During playback, select a portion of the
video you want to save. Pause
playback.
3. Right-click anywhere on the main
window and select Capture>Marker In.
Play video.
4. Advance the video/select the end-point
for the video. Right-click anywhere on
the main window and select
Capture>Marker Out.
Figure 18.2 Capture sub menu
5. Right-click anywhere on the main
window and select Capture>Export.
6. In the Save As dialogue window, select
a file name and save location and click
Save.
Note: Captured files carry the file
extension .VVF.
Please allow a few moments to save the captured video. This could take several moments
depending on the size of the capture.
With the captured video now saved to your PC, you can use Lorex Client to export the file as an
AVI for greater flexibility of playback among other media players.
32
Using Lorex Client
Exporting to AVI
Lorex Client allows you export .VVF files to .AVI for increased flexibilty when playing back the
video in third-party media players, such as VLC™ and DivX Player™. Converting the file to AVI
can be particularly useful if you need to provide authorities with copies of your video data if there
is a security incident at your business or home.
Note: The DivX or XviD codec (not included) is required if viewing AVIs in Windows Media
Player™.
Figure 18.3 Exporting to AVI
To export video files:
1. Open Lorex Client.
2. Right-click anywhere on the main display screen and select Export>AVI.
3. In the Export window, under Input File, click Browse to select the file to be exported (.VVF).
4. Under Output File, click Browse to select a save location for the exported file (by default,
output files are saved to the save location as the input file).
Note: Output files carry the default naming convention, CAPTURE-CH(channelnumber).avi.
5. Under Export Channel, check/uncheck the boxes for channels 1~4.
6. Under Audio, check/uncheck the box to include/exclude audio in the file conversion.
7. Under Compression, click Select. In the Video Compression window, select a compression
type from the drop-down menu and click OK. See “Appendix 5: Compression Codecs” on
page 41.
8. In the Export window, click OK. File conversion begins. Exporting to AVI could take several
moments depending on the number of channels being exported, the inclusion of audio, and
the size of the original file.
Note: Depending on your compression type, windows may open windows showing the progress
of the file conversion for each channel. When the files are finished exporting to AVI, you can
close these windows.
Note: Lorex Client creates a placeholder file, dummy.avi in the Output folder.
33
Using Lorex Client
Options
Use the Options window to configure general options, on-screen display, and the default path for
still capture.
Figure 18.4 Options menu
To configure options:
1. Under General, check/uncheck the boxes to enable/disable the following:
• Always on Top: Keep the Lorex Client window on top of other application windows. Shortcut Key, A.
• Show playback time: During playpack, show/hide the date-stamp. Shortcut Key, T.
• Repeat playback: Repeat (loop) playback. Shortcut key, R.
• Use DirectDraw: Enable/disable DirectDraw to enhance visual quality during playback.
Note: DirectDraw is part of Microsoft DirectX.
2. Under On screen display date/time format, select your desired format for the date and time
from the drop-down menu. For example, yyyy/mm/dd, hh/mm/ss; or Month Day, AM/PM, hh/
mm/ss yyyy.
3. Under Path for still capture, click Browse to select a save location for the still image bitmap
(.BMP) files. By default, C:\VxCapture.
4. When you are finished, click OK to save your settings, or click Cancel to exit without saving.
34
Appendix 1: System Specifications
Appendix 1: System Specifications
Description
Specification
Video Format
NTSC / PAL
Operating System
RTOS
VGA Output
VGA
Video Input
4 x BNC (1Vp-p 75 ohms)
Audio Input
1 x RCA line-in
Video Output
1 x BNC (Monitor Out)
Audio Output
1 x RCA line-out
Language
Multi-language
Display Frame
NTSC: 120 fps (4 x 30 fps)
PAL: 100 fps (4 x 25 fps)
Recording Frame
NTSC: 60 fps max.
PAL: 50 fps max.
Recording
Resolution
NTSC: 640x224
Display Resolution
NTSC: 640x448
PAL: 640x272
PAL: 640x544
Compression
Format
MJPEG
Hard Disk
3.5" SATA (1 TB max.)
Backup
USB (front panel)
Power Supply
12V DC / 4 A (AC 100V~240V 50/60 Hz)
Dimensions
220 mm x 228 mm x 48 mm
(WxDxH)
8.66" x 8.99" x 1.89"
Weight
1.5 kg / 3.31 lbs
Normal: 12KB/frame; High: 15KB/frame; Highest: 20KB/frame
As our products are subject to continuous improvement, Lorex Technology Inc. and its
subsidiaries reserve the right to modify product design, specifications, and prices without notice
and without incurring any obligation.
E&OE
35
Appendix 2: Full Connectivity Diagram
Appendix 2: Full Connectivity Diagram
The following diagram outlines a general set of connections available with the DVR.
LINE IN AUDIO /
SPEAKERS
(not included)
VGA MONITOR
(not included)
DVR
POWER
(to power
adaptor)
OBSERVATION SYSTEM,
MONITOR, TV
(not included)
Figure 19.0 Full connectivity diagram
36
BNC CAMERAS
Appendix 3: Using Listen-in Audio
Appendix 3: Using Listen-in Audio
Listen-in audio allows you to listen to, and record live audio on the system.
You can record one audio channel (mono) with an RCA (male) audio cable.
LINE IN AUDIO /
AUDIO CAPABLE CAMERA
(not included)
DVR
AUDIO OUT /
SPEAKERS
(not included)
Figure 20.0 Audio connection diagram
To enable listen-in audio:
1. Connect an RCA audio cable (male) from an audio capable camera to the AUDIO IN port on
the rear panel.
2. Connect an RCA audio out cable (male) to the AUDIO OUT port on the rear panel.
3. From the Setup Menu, select Audio and press
4. Select Record and press
5. Press
settings.
. The Audio menu opens.
to turn audio recording On.
until the Exit menu appears. Select Save & Exit and press
to save your
37
Appendix 4: Replacing the Hard Drive
Appendix 4: Replacing the Hard Drive
The system comes with a pre-installed 3.5" SATA hard drive, however the unit will work with a
replacement single hard drive (up to 1 TB).
Note: Make sure that the system is OFF and the power cable has been disconnected before
changing the hard drive.
Removing the Hard Drive
To remove the hard drive:
1. Remove seven screws from the cover of the
housing: three from the top half of each side
panel; one from the top near the rear panel.
2. Gently lift off the cover.
3. With your hand supporting the hard drive, turn
the unit upside down. Remove the four
mounting screws from the bottom of the unit.
Turn the unit right side up.
Figure 21.1 Remove cover.
4. Disconnect the power and data cables.
5. Remove the hard drive.
Note: Make sure to keep the two sets of screws
(cover, mounting) in a safe place.
Figure 21.2 Support the HDD with your hand and remove
mounting screws.
Figure 21.0 Remove seven screws from cover
38
Figure 21.3 Carefully remove the HDD from housing.
Appendix 4: Replacing the Hard Drive
Replacing the Hard Drive
To replace the hard drive:
1. Firmly connect the power and data cables to the replacement SATA hard drive—each cable
can only connect in one way.
Figure 21.4 Connect the power and data cables.
2. Carefully place the hard drive in the housing.
Note: Make sure not to damage any of the cables when placing the hard drive in the housing.
Note: Make sure no cables are caught beneath the drive.
3. With your hand supporting the hard drive, turn the housing upside down: replace the four
screws on the bottom of the housing.
4. Turn the housing right side up. Replace the cover, making sure to slide the cover toward the
front panel until flush.
5. Replace the screw on the top panel (x1) and side panels (x6).
6. Reconnect all cameras and cables.
7. Power on the system. If you have installed a new hard drive, you must format the drive
before using the system.
Note: The system will detect the hard drive a few seconds after powering on the system. The
system will prompt you if the hard drive is not detected.
39
Appendix 4: Replacing the Hard Drive
Formatting the Hard Drive
Use Hard Disk Setup in the System menu to format the internal hard drive.
Note: You must stop recording before attempting to format the hard drive.
ATTENTION: Formatting erases all recorded video data on the hard
drive. Formatting cannot be undone.
System settings are not affected by fornatting.
To format the hard drive:
1. Open the Setup menu. Select System and press
. The System menu opens.
2. From the System menu, select Hard Disk Setup and press
3. Select Format HDD and press
.
.
4. Enter your 6-character system password. The system begins formatting the hard drive.
This could take several moments depending on the size of your system’s hard drive.
Once formatting is complete, the system will return to Live Mode.
40
Appendix 5: Compression Codecs
Appendix 5: Compression Codecs
When exporting a .VVf file to .AVI, you can choose any of the following codecs for compression:
• Cinepak Codec by Radius
• Intel 4:2:0 Video V2.50
• Intel Indeo(R) Video R3.2
• Intel IYUV Codec
• Microsoft RLE
• Microsoft Video 1
• Microsoft H.263 Video Codec
• Microsoft H.261 Video Codec
• Indeo® Video 5.10
• Sunplus 32-bit Compressor
• DivX® 6.1.1 Codec (1 Logical)
• DivX® 6.1.1 YV12 Decoder
• Xvid MPEG-4 Codec
• Full Frames (uncompressed)
Note: Video Codecs for playback are NOT supplied with this software. Codecs can be
downloaded from such sites as www.microsoft.com or www.divx.com
41
Troubleshooting
Troubleshooting
When a malfunction occurs, it may not be serious and can be corrected easily. The following
describes the most common problems and solutions. Please refer to the following before calling
Lorex Technical Support:
Error
Possible Causes
Solutions
• DVR Unit is not
receiving power, or is
not powering up
• Cable from power adaptor is
loose or is unplugged
• Confirm that all cables are connected correctly
• Cables are connected, but DVR
unit is not receiving sufficient
power
• Confirm that the unit is powered on (LED
indicators on the front should be ON)
• Confirm that the power adaptor is securely
connected to the back of the unit
• If the unit is connected through a power bar or
surge protector, try bypassing the bar and
connecting the power directly to the wall outlet
• Confirm that there is power at the outlet:
• Connecting the power cable to another outlet
• Test the outlet with another plugged device
(such as an electric calculator or phone
charger)
• Remote control is
not detected by the
system
• Batteries in the remote control
are drained
•
• There are no batteries in the
remote control
• Hard drive is not
detected by the
system
• Hard drive cables are loose or
not properly connected
• Remove the houseing and check that hard drive
cables are firmly connected
• There is no hard drive in the
system
• Open the housing and install a 3.5" SATA hard
drive
• Overwrite is not enabled
• Turn Overwrite on. Setup>System>Hard Disk
Setup.
Hard drive is full (0%)
and the unit is no
longer recording
42
• Install a fresh CR2025 lithium battery in the
remote control
Troubleshooting (cont’d.)
Troubleshooting (cont’d.)
Error
Possible Causes
Solutions
• There is no picture
on selected channels
/ camera picture is
not being displayed
• Camera cables are loose or
have become disconnected
• Check the camera video cable and connections
• Disconnect and reconnect the cable at the DVR
and at the Camera
• Try moving the camera to another channel or use
another cable
• The image on the
DVR appears, but
does not have sound
• Audio cables are loose or have
been disconnected
• Check the AUDIO connections to the DVR
• Audio channels are disabled in
the system menu
• Check the Configurations: Setup Menu>Audio
• Volume on external speakers
(not included) is low or off
• Increase volume on external speakers (not
included)
43
LOREX PRODUCT LIMITED WARRANTY
Revision 1.0
1 year (Warranted parts do not include Bulbs, LED’s and Batteries)
Lorex warrants, to the original retail purchaser only (the “Purchaser”), that this item (the “Product”) if properly used
and installed, and where applicable, the CD-ROM on which the accompanying software is provided, is free from
manufacturing defects in material and workmanship, provided the Product is used in normal conditions and is
installed and used in strict accordance with the instructions contained.
This warranty shall be for the following warranty periods (the “Warranty Period”), commencing on the date the
Purchaser buys the Product at retail in an unused condition.
Parts and Labor:
Lorex’s obligations under this warranty shall be limited to
• The repair and or replacement of the product by means of hardware and/or software (at option of Lorex);
• The replacement of any warranted parts found by Lorex to be defective in the Product or, in Lorex’s sole
discretion, the replacement of the Product found be Lorex to be defective.
• If Lorex is unable to repair or replace the Product or CD-ROM, refund the then-current value of the Product.
Any replacement parts furnished by Lorex in connection with this warranty shall be warranted to the Purchaser for
a period equal to the un expired portion of Warranty Period for the Product.
Warranty Exclusions
This warranty does not apply to Bulbs, LED’s and Batteries supplied with or forming part of the product.
This warranty is invalidated if other than Lorex accessories are or have been used in or in connection with the
Product or in any modification or repair is made to the Product by other than a service depot authorized by Lorex.
This warranty does not apply to defects or damages arising by use of the Product in other than normal (including
normal atmospheric, moisture and humidity) conditions or by installation or use of the Product other than in strict
accordance with the instructions contained in the Product’s Owner’s Manual.
This warranty does not apply to defects in or damages to the Product caused by (i) negligent use of the Product,
(ii) misuse, abuse, neglect, alteration, repair or improper installation of the Product, (iii) electrical short circuits or
transients, (iv) Purchaser usage not in accordance with product installation, (v) use of replacement parts not
supplied by Lorex (vi) improper Product maintenance, or (viii) accident, fire, flood or other Acts of God.
This warranty does not cover the performance or functionality of any computer software included in the package
with the Product. This warranty only covers defects in the CD-ROM media such as a broken or a defect in the
CD-ROM that would prevent the CD-ROM from being read by your personal computer’s CD-ROM drive. Lorex
makes no warranty that the software provided with the Product will function without interruption or otherwise be
free of anomalies, errors or ‘Bugs’. Lorex makes no warranty with regard to any software provided with the
Product unless specifically set forth otherwise in a license agreement accompanying such software. This warranty
does not cover any costs relating to removal or replacement of any Product, CD-ROM, or software installed on
your computer.
Lorex reserves the right to make changes in design or to make additions to or improvements in its products
without incurring any obligation to modify any product which has already been manufactured. Lorex will make
every effort to provide updates and fixes to its software via its website. This warranty does not cover any
alteration or damage to any other software that may be or may become resident on the users system as a result
of installing the software provided. This warranty is in lieu of other warranties, express or implied, and Lorex
neither assumes nor authorizes any person to assume for it any other obligation or liability in correction with the
sale or service of the Product. In no event shall Lorex be liable for any special or consequential damages arising
from the use of the Product or arising from the malfunctioning or non-functioning of the Product, or for any delay
in the performance of this warranty due to any cause beyond its control.
This warranty shall not apply to the appearance or accessory items including, but not limited to cabinets, cabinet
parts, knobs etc., and the uncrating, setup, installation or the removal and reinstallation of products after repair.
Lorex does not make any claims or warranties of any kind whatsoever regarding the Product’s potential, ability or
effectiveness to prevent minimize, or in any way affect personal or property damage or injury. Lorex is not
responsible for any personal damage, loss or theft related to the Product or to its use for any harm, whether
physical or mental related thereto. Any and all claims or statements, whether written or verbal, by salespeople,
retailers, dealers or distributors to the contrary are not authorized by Lorex, and do not affect this provision of this
warranty.
Lorex’s responsibility under this, or any other warranty, implied or expressed, is
limited to repair, replacement or refund, as set forth above. These remedies are the
sole and exclusive remedies for any breach of warranty. Lorex is not responsible for
direct, special, incidental, or consequential damages resulting from any breach of
warranty or under any other legal theory including but not limited to, loss profits,
downtime, goodwill, damage to or replacement of equipment and property and any
costs of recovering, reprogramming or reproducing any program or data stored in or
used with a system containing the Product CD-ROM or accompanying software.
Lorex does not warrant that the software will operate with any other software except
that which is indicated. Lorex cannot be responsible for characteristics of third party
hardware or software which may effect the operation of the software included.
The purchaser may have other rights under state, provincial, or federal laws and
where the whole or part of any item of this warranty is prohibited by such laws, it
shall be deemed null and void, but the remainder of the warranty shall remain in
effect.
All expressed and implied warranties are limited in duration to the limited warranty
period. No warranties apply after that period. Some states do not allow limitation on
how long an implied warranty lasts, so this limitation may not apply to you. Some
states do not allow the exclusion or limitation of incidental or consequential
damages, so the above warranty may not apply to you. This limited warranty gives
you specific legal rights and you may also have other rights that vary from state to
state.
Obtaining Service
In order to obtain service, please make sure that you have registered your product
on-line (www.lorexcctv.com) in the warranty registration section. Should the
Product require service under this warranty, the Purchaser must provide Lorex with
a copy of his/ her original, dated bill of sale; receipt or invoice, failing which Lorex
will not perform any of its obligations under this warranty. If you return the Product
and/or CD-ROM to Lorex, you must assume the risk of damage or loss during
shipment. You must use the original packaging or the equivalent, and you must pay
postage.
To claim on this warranty, proceed with the following steps.
ii). If the unit was purchased in Canada proceed as follows:
Please contact our customer service department to obtain a return
authorization number.
Return the unit to:
Lorex Service Center.
300 Alden Road, Markham, Ont. L3R 4C1
iii) If the unit was purchased in Europe please visit:
1 Pack the Product in a well-padded sturdy carton.
2.
i). If the unit was purchased in the United States proceed as follows:
a.
Please contact our customer service department to obtain a return
authorization number.
Return the unit to:
Lorex Service Center
2375 Hadley Rd, Plainfield, IN 46168
b.
a.
b.
www.lorexinternational.com for return instructions.
TOLL FREE CUSTOMER SUPPORT
North America: 1-888-42-LOREX (1-888-425-6739)
Local: 905-940-5355
International: 800-42-LOREX 0 (800-425-67390)
www.lorexcctv.com
Always use discretion when installing video and/or audio surveillance equipment especially
when there is perceived privacy. Inquire regarding federal, state and/or local regulations
www.strategicvista.com
applicable to the lawful installation
of video and or audio recording or surveillance. Party
consent may be required.
GARANTIE LIMITÉE DES PRODUITS LOREX
Lorex garantit à l'acheteur original (ci-après désigné comme étant "l'acheteur") dans un magasin au
détail seulement, et que ce produit (ci-après désigné comme étant le "produit"), s'il est installé
correctement et - s’il y a lieu - utilisé conformément aux instructions ci-incluses, et le disque CDROM qui comporte le logiciel, seront libres de tout défaut de fabrication, tant dans les pièces que la
main-d'oeuvre, pourvu que le produit soit utilisé dans des conditions normales et installé et utilisé
strictement selon les instructions incluses dans le guide qui l'accompagne.
Cette garantie couvrira la période mentionnée ci-dessous (ci-après désignée comme étant la
"période de garantie"), commençant le jour où l'acheteur se procure le produit à l'état neuf dans un
magasin au détail.
Pièces et main-d'oeuvre :
1 année (les pièces couvertes n'incluent
pas les ampoules, voyants à DEL ni les
piles).
Les obligations de Lorex selon les termes de cette garantie se limitent exclusivement aux points
suivants :
•
Lorex se réserve le droit de réparer ou de remplacer, sa seule discrétion, le logiciel et/ou le
matériel.
•
Le remplacement des pièces sous garantie que Lorex estime être défectueuses dans le
produit ou le disque CD-ROM ou, à sa seule discrétion, le remplacement du produit jugé
défectueux.
•
Si Lorex ne peut réparer ni remplacer le produit ou le disque CD-ROM, rembourser la valeur
monétaire du produit ou du disque CD-ROM en cours au moment de l'achat.
Toutes les pièces remplacées par Lorex seront couvertes pendant la période résiduelle de la
garantie dudit produit.
Exclusions de la garantie
Pour obtenir du service, veuillez vous assurer que vous avez inscrit votre produit en ligne
(www.lorexcctv.com) dans la section d'abonnement à la garantie. Cette garantie ne couvre pas
les ampoules, voyants à DEL ni les piles incluses avec le produit ou faisant partie de celui-ci.
Cette garantie deviendra nulle si des accessoires autres que ceux vendus ou distribués par Lorex
sont utilisés ou ont été utilisés conjointement avec le produit ou si des modifications ou des
réparations ont été effectuées au produit par une entité autre qu'un centre de service autorisé par
Lorex.
Cette garantie ne s'applique pas aux défauts ni aux dommages survenus suite à une utilisation
anormale du produit (incluant des conditions atmosphériques et des taux d'humidité anormaux) ou
suite à une installation ou une utilisation du produit autre que celle décrite dans le guide
accompagnant le produit.
Cette garantie ne s'applique pas aux défauts ni aux dommages causés au produit suite à (i) une
utilisation insouciante du produit, (ii) mauvaise utilisation, abus, négligence, modification ou
mauvaise installation du produit, (iii) court-circuits ou transitoires électriques, (iv) tout usage de
l'acheteur qui ne correspond pas à l'installation prescrite du produit, (v) l'utilisation de pièces non
fournies par Lorex, (vi) un entretien inadéquat du produit, ou (vii) tout accident, incendie, inondation
ou autres désastres naturels.
Cette garantie ne couvre pas la performance ni la fonctionnalité de tout logiciel informatique inclus
avec le produit. Cette garantie ne couvre pas les défauts que pourrait contenir le support optique
(disque CD-ROM) ou magnétique (disquette), tel qu'un CD-ROM brisé ou comportant un défaut qui
l'empêcherait d'être lu adéquatement par le lecteur de disque de votre ordinateur. Lorex ne garantit
pas que le logiciel fourni avec le produit fonctionnera sans interruption ni qu'il sera libre de tout
défaut, d'erreurs ou de 'bogues'. Lorex ne garantit pas le logiciel inclus à moins que cela ne le soit
mentionné spécifiquement dans l'entente de la licence incluse avec le produit. Cette garantie ne
couvre pas les frais se rapportant à l'enlèvement ni à la réinsertion de tout produit, logiciel,
périphérique ou disque CD-ROM installé sur votre ordinateur.
Lorex se réserve le droit de modifier la conception ou d'apporter des ajouts ou des améliorations à
ses produits, sans obligation de sa part de modifier les produits déjà fabriqués. Lorex fera tout en
son pouvoir pour fournir des améliorations et des réparations à son logiciel via son site web.
Cette garantie ne couvre pas les altérations ni les dommages effectues tout autre logiciel, ni les
bogues pouvant résider de fa on permanente sur le système de l'utilisateur suite l'installation du
logiciel ci-inclus.
Cette garantie a préséance sur toutes les autres garanties tacites ou explicites, incluant la garantie en qualité
loyale et marchande et les aptitudes visant toute autre obligation ou responsabilité de la part de Lorex, et par les
présentes, Lorex n’autorise aucune personne ni entité à assumer pour elle nulle autre responsabilité en rapport
avec la vente de ce produit. Lorex ne sera pas tenue responsable, en aucune circonstance, des dommagesintérêts directs ou indirects survenant de l'utilisation du produit ou suite au mauvais fonctionnement ou à l'absence
de fonctionnement dudit produit, ainsi que pour tout délai dans l'exécution de cette garantie suite à des
circonstances hors du contrôle de Lorex.
Lorex ne garantit d’aucune manière l'apparence extérieure du produit, ni les pièces ou accessoires incluant, mais
ne s'y limitant pas, le boîtier, les pièces du boîtier, les boutons, etc., ainsi que le déballage, l'installation,
l'enlèvement et la réinstallation du produit après une réparation.
Lorex ne garantit pas et ne fait aucune revendication en ce qui a trait au potentiel, à la capacité ou l'efficacité de
prévenir, réduire ou d'une façon quelconque, d'influer sur les dommages à la propriété privée ou sur les blessures
corporelles. Lorex ne sera pas tenue responsable des blessures corporelles, dommages à la propriété
personnelle, perte ni au vol se rapportant de près ou de loin au produit ou son usage dans un cadre malveillant,
qu'il soit physique ou mental. Lorex n'autorise aucunement les représentants, détaillants ou grossistes, à faire des
revendications ou des énoncés de la part de Lorex, tant par voie écrite que verbale et ces énoncés n'influent
d'aucune manière sur les clauses de cette garantie.
La seule responsabilité de Lorex, selon les termes de cette garantie, qu'ils soient tacites ou explicites, se limite à
une réparation, un remplacement ou un remboursement, selon les clauses décrites dans les présentes. Ces
recours constituent les seuls auxquels a droit l'acheteur pour les bris des clauses de la garantie. Lorex ne sera pas
responsable des dommages-intérêts spéciaux, directs ou indirects, qui résulteraient d'un bris des clauses de cette
garantie ou de toute autre convention législative, incluant mais ne s'y limitant pas, les pertes de profits, pannes de
courant immobilisant des équipements, la valeur ajoutée des biens incorporels, les dommages effectués au produit
et à la propriété ou les coûts reliés à leur remplacement, ainsi que les frais de recouvrement, reprogrammation ou
reproduction d'un programme ou des données stockées dans un système contenant le disque CD-ROM du produit
ou le logiciel qui accompagne celui-ci.
L'acheteur peut bénéficier de certains droits provinciaux ou fédéraux additionnels et toute clause de cette garantie
qui soit prohibée par de telles lois sera jugée nulle et sans effet mais les autres clauses demeureront en vigueur.
Lorex ne garantit pas que ce logiciel fonctionnera conjointement avec tout autre logiciel ou suite logicielle, ˆ
moins que cela ne soit indique. Lorex ne sera pas tenue responsable des caractéristiques ni des fonctions du
matériel ou des logiciels d'un tiers pouvant entrer en conflit avec le fonctionnement du logiciel ci-inclus.
Toutes les garanties tacites ou explicites se limitent à la durée de la garantie limitée. Aucune garantie ne sera
applicable après cette période de temps. Certains états ou provinces ne permettent pas de restrictions en ce qui a
trait aux termes d’une garantie tacite, ni d’exclusions aux dommages-intérêts directs ou indirects et il se peut que
ces restrictions ne s'appliquent pas à vous. Cette garantie donne à l’acheteur original des droits spécifiques et il se
peut que d’autres droits, variant d’un état ou d’une province à l’autre, puissent lui être conférés.
Obtention du service
Si l'acheteur a besoin de service pour son produit, selon les termes de cette garantie limitée, il doit fournir à Lorex
une copie de la facture d'achat affichant clairement la date et l'endroit où le produit a été acheté. Sans cette
preuve d'achat, Lorex ne sera pas dans l'obligation de remplir ses obligations envers l'acheteur. Si vous retournez
le produit et/ou le disque CD-ROM à Lorex, vous devez assumer le risque que ceux-ci soient endommagés ou
perdus au cours de l'expédition. Vous devez emballer le produit dans sa boîte originale ou un emballage adéquat
et vous devez défrayer les coûts d'expédition à l'une des adresses mentionnées ci-dessous.
Pour bénéficier du service sous garantie, vous devez suivre les étapes ci-dessous :
1.
Emballez le produit dans une boîte solide et remplie de matériau d'expédition.
2.
i) Si l'appareil a été acheté aux États-Unis, suivez ces étapes-ci :
a. Veuillez contacter notre département de service à la clientèle pour obtenir un numéro
d'autorisation pour le retour.
b. Retournez le produit à : Lorex Customer Service
2375 Hadley Rd, Plainfield, IN 46168
ii) Si l'appareil a été acheté au Canada, suivez ces
étapes-ci :
a. Veuillez contacter notre département de service à la clientèle pour obtenir un numéro
d'autorisation pour le retour.
b.
Retournez le produit à : Lorex Customer Service
300 Alden Road, Markham, ON L3R 4C1
iii) Si l'unité a été achetée dans Europe veuillez visiter : www.lorexinternational.com pour les
instructions de retour
COMPOSEZ LA LIGNE D’ASSISTANCE SANS FRAIS AUS CONOMMATEURS:
L'Amérique du nord: 1-888-42-LOREX (1-888-425-6739)
Local : 905-940-5355
International : 800-42-LOREX 0 (800-425-67390)
www.lorexcctv.com
Soyez toujours très discret lorsque vous installez des systèmes de surveillance, surtout dans les endroits plus retirés. Informezvous au sujet des lois et règlements municipaux, provinciaux ou fédéraux qui s’appliquent à l’installation d’appareils de
surveillance audio et vidéo. Il se peut que le consentement de la partie surveillée soit exigé.
GARANTÍA LIMITADA DEL PRODUCTO LOREX
Lorex garantiza, sólo al comprador original al por menor (el “Comprador”) que este artículo
(el “Producto”), si se usa e instala debidamente, y – si hay lugar - el CD-ROM en el que se proporciona el
software asociado, está libre de defectos de fabricación en materiales y mano de obra, sujeto a que el Producto
sea usado en condiciones normales y que sea instalado y usado estrictamente de acuerdo con las instrucciones
contenidas.
Esta garantía será para los siguientes períodos de garantía (el “Período de Garantía”), a partir de la fecha en que
el Comprador adquiera el Producto al por menor en la condición de no haber sido usado previamente.
Repuestos y Mano de Obra:
1 año (Las piezas garantizadas no incluyen bombillas, LEDs y baterías)
Las obligaciones de Lorex bajo esta garantía estarán limitadas a:
•
la reparación o el reemplazo del producto por medio de hardware y/o software (a opción de Lorex).
•
el reemplazo de cualquier parte garantizada que Lorex determine que está defectuosa en el Producto o
CD-ROM o, por decisión única de Lorex, al reemplazo del Producto que Lorex encuentre defectuoso.
•
Si a Lorex no le es posible reparar o reemplazar el Producto o el CD-ROM, se devolverá el valor vigente
en ese momento del Producto o CD-ROM.
Se garantizará al Comprador cualquier pieza de repuesto provista por Lorex en conexión con esta garantía por
un período igual a la parte no vencida del Período de Garantía del Producto.
Exclusiones de la garantía
Esta garantía no se aplica a las bombillas, LEDs y baterías suministradas con el producto o que formen parte del
mismo.
Esta garantía quedará nula si se han usado accesorios que no son Lorex en el Producto o en relación con el
mismo o si se hace alguna modificación o reparación al Producto en algún taller que no sea un local de servicio
autorizado por Lorex.
Esta garantía no se aplica a defectos o daños resultantes del uso del producto en condiciones diferentes a las
normales (incluyendo condiciones atmosféricas o de humedad normales) o por la instalación o uso del Producto
en forma distinta a seguir estrictamente las instrucciones contenidas en el Manual del Propietario del Producto.
Exclusiones de la garantía
Esta garantía no se aplica a las bombillas, LEDs y baterías suministradas con el producto o que formen parte del
mismo.
Esta garantía quedará nula si se han usado accesorios que no son Lorex en el Producto o en relación con el
mismo o si se hace alguna modificación o reparación al Producto en algún taller que no sea un local de servicio
autorizado por Lorex.
Esta garantía no se aplica a defectos o daños resultantes del uso del producto en condiciones diferentes a las
normales (incluyendo condiciones atmosféricas o de humedad normales) o por la instalación o uso del Producto
en forma distinta a seguir estrictamente las instrucciones contenidas en el Manual del Propietario del Producto.
Esta garantía no se aplica a defectos o daños al Producto causados por (i) uso negligente del Producto, (ii) mal
uso, abuso, negligencia, alteración, reparación o instalación incorrecta del Producto, (iii) cortocircuitos o
corrientes eléctricas transitorias, (iv) uso por el Comprador que no está de acuerdo con la instalación del
producto, (v) uso de piezas de repuesto no suplidas por Lorex (vi) inadecuado mantenimiento del Producto, o
(vii) accidente, incendio, inundación u otros accidentes naturales.
Esta garantía no cubre el rendimiento o funcionalidad de ningún software de computadora incluido en el paquete
con el Producto. Esta garantía sólo cubre defectos en el material de CD-ROM, tal como roturas o defectos en el
CD-ROM que impida que sea leído por la unidad de CD-ROM de su computadora personal. Lorex no garantiza
que el software provisto con el Producto funcione sin interrupción o que de otra forma esté libre de anomalías,
errores o “bugs”. Lorex no ofrece ninguna garantiza con respecto a algún software provisto con el equipo a
menos que específicamente se establezca de otra forma en un acuerdo de licencia que acompañe a dicho
software.
Esta garantía no cubre ningún costo relativo a la remoción o reemplazo de algún Producto, CD-ROM, o software
instalado en su computadora.
Lorex se reserva el derecho de hacer cambios en el diseño o hacer adiciones o mejoras a sus productos sin
incurrir en ninguna obligación de modificar algún producto que ya haya sido fabricado.
Lorex tratará en lo posible de proporcionar actualizaciones y arreglos a su software por medio de su página en la
red.
Esta garantía no cubre ninguna alteración ni daño a algún otro software que pueda ser instalado o pueda quedar
instalado en el sistema del usuario como resultado de la instalación del software provisto.
Esta garantía es el reemplazo de otras garantías, expresas o implícitas, y Lorex no asume ni autoriza a ninguna
persona a asumir por ella ninguna obligación en relación con la venta o servicio del producto. En ningún caso
Lorex será responsable por ningún daño o perjuicio especial o consecuente resultante del uso del Producto o de
su mal funcionamiento o incapacidad de funcionar, o por cualquier demora en la atención de esta garantía
debida a causas fuera de su control.
Esta garantía no se aplicará a la apariencia o artículos accesorios incluyendo, sin estar limitado a ellos,
gabinetes, piezas de gabinetes, perillas, etc., y el desembalaje, instalación, configuración, o remoción y
reinstalación del producto después de ser reparado.
Lorex no hace ninguna de cada declaración ni garantía de ninguna clase con respecto al potencial, capacidad o
eficacia del Producto para evitar, minimizar o en alguna forma afectar a los daños o lesiones personales o a la
propiedad. Lorex no es responsable por ningún daño personal, siniestro o robo relacionado con el Producto o a su
uso para cualquier daño, sea físico o mental relacionado con el mismo. Cualquier afirmación o declaración, sea
escrita o verbal, hecha por vendedores, minoristas o distribuidores en sentido contrario no es autorizada por
Lorex y no afecta esta disposición de esta garantía.
La responsabilidad de Lorex según ésta o cualquier otra garantía, implícita o explícita, está limitada a la
reparación, reemplazo o reembolso, como se establece anteriormente. Estas compensaciones son el único y
exclusivo remedio por cualquier incumplimiento de garantía. Lorex no es responsable por daños y perjuicios
directos, especiales, incidentes, o consecuentes resultantes de algún incumplimiento de garantía o bajo cualquier
otra teoría legal, incluyendo pero sin estar limitada a: pérdida de utilidades, paralización, plusvalía, daños o
reemplazo de equipos y propiedad y cualquier costo de recuperar, reprogramar o reproducir cualquier programa o
datos almacenados o usados con un sistema que contenga el CD-ROM del Producto o el software que lo
acompaña.
Lorex no garantiza que el software operará con ningún otro software excepto con el que se indica. Lorex no
puede ser responsable de las características de hardware o software de terceras personas que puedan afectar la
operación del software incluido.
El comprador puede tener otros derechos de acuerdo con las leyes federales, provinciales o estatales y cuando
toda esta garantía o parte de la misma sea prohibida por dichas leyes, será considerada nula, pero el resto de la
garantía permanecerá vigente.
Todas las garantías expresadas e implícitas están limitadas en duración al período de garantía limitada. Ninguna
garantía se aplicará después de dicho período. Algunos estados no permiten limitación a la duración de una
garantía implícita, de modo que esta limitación puede no serle de aplicación. Algunos estados no permiten la
exclusión o limitación de daños y perjuicios incidentes o consecuentes, por lo que la garantía anterior puede no
serle de aplicación. Esta garantía limitada le otorga derechos legales específicos y usted puede también tener
otros derechos que varía de un estado a otro.
Cómo obtener servicio
ii). Si la unidad fue comprada en Canadá proceda en la siguiente forma:
Para devoluciones por favor contacte nuestro departamento de servicio para obtener un número de
autorización.
Devuelva la unidad a:
Lorex Customer Service.
300 Alden Road, Markham, Ont. L3R 4C1
Para devoluciones por favor contacte nuestro departamento de servicio para obtener un número de
autorización
Devuelva la unidad a:
Lorex Customer Service
2375 Hadley Rd, Plainfield, IN 46168
Empaque el Producto en una caja robusta bien acolchada.
i). Si la unidad fue comprada en Estados Unidos proceda en la siguiente forma:
Con el fin de obtener servicio, por favor asegúrese de registrar haber registrado su producto en nuestra pagina
web www.lorexcctv.com en la sección de registro de garantía. Si el Producto necesitase servicio bajo esta
garantía, el Comprador debe hacer llegar a Lorex una copia del recibo o factura de compra, con su fecha
respectiva, sin lo cual Lorex no estará obligada a cumplir con ninguna de sus obligaciones bajo esta garantía. Si
devuelve el Producto y/o el CD-ROM a Lorex, debe usted asumir el riesgo de daño o pérdida durante el envío.
Debe usar el envase original o equivalente y debe pagar el flete.
Para hacer un reclamo bajo esta garantía, proceda con los siguientes pasos.
1.
2.
1.
a.
b.
a.
b.
iii) Si la unidad fue adquirida en Europa y desea devolver el producto por favor visite:
www.lorexinternational.com para obtener instrucciones.
NUMERO GRATUITO DE SERVICIO A CLIENTES:
Norteamérica: 1-888-42-LOREX (1-888-425-6739)
Internacional: 800-42-LOREX 0 (800-425-67390)
Local : 905-940-5355
www.lorexcctv.com
Use siempre discreción cuando instale equipo de vigilancia por video y/o audio especialmente cuando se
percibe privacidad. Consulte acerca de las regulaciones federales, estatales y /o locales aplicables a la
instalación legal de equipos de grabación o vigilancia por video y/o audio. Puede requerirse el
consentimiento de las partes.
It’s all on the Web!
Tout est sur le Web!
¡Todo está en la Web!
Product Information
Information sur le produit
Información acerca del producto
Specification Sheets
Fiches signalétiques
Fichas de especificaciones
User Manuals
Guides de l’utilisateur
Guías del usuario
Software Upgrades
Mises à jour du logiciel
Actualizaciones del programa
Quick Start Guides
Guides de démarrage rapide
Guías de arranque rápido
Firmware Upgrades
Mises à jour du micro-logiciel
Actualizaciones del microprograma
VISIT / VISITEZ / VISITA
www.lorexcctv.com
www.lorexcctv.com
Lorex Technology Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising