[email protected]
800-683-8353
Easy-Change Under-Sink Drinking Water Filter System
Installation and Operating Instructions
Model RV-EZ
Specifications
Range / Capacity
Level 1
Level 3
Level 4
Pressure Range:
30 – 100 psi (2.1 – 6.9 bar)
Temperature Range:
40–100 ° F (4.4 – 37.7 ° C)
Rated Service Flow:
0.5 gpm (1.9 Lpm)
Filter Capacity:
3000 gallons (11,356 L)
Turbidity:
500 gallons (1893 L)
5 NTU max
Parts Included:
Precautions
•
filter head with built-in bracket
•
filter cartridge
•
mounting screws
•
water supply adapter
•
lead-free faucet and fittings
•
1⁄4-inch plastic tubing
•
bypass fitting kit (RV-BYP) for winterization
•
cartridge change reminder sticker
WARNING: Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the system. Systems
certified for cyst reduction may be used on disinfected waters that may contain
filterable cysts.
CAUTION: This filter must be protected from freezing, which can cause cracking of
the filter and water leakage.
CAUTION: Because of the product’s limited service life and to prevent costly
repairs or possible water damage, we strongly recommend that the head of the filter be
replaced every ten years. If the head of your filter has been in use for longer than this
period, it should be replaced immediately. Date the top of any new head to indicate the
next recommended replacement date.
Tools Required
•
•
•
phillips screwdriver
hand or electric drill (cordless recommended)
utility knife (for plastic tubing)
towel
pencil
tape measure
•
•
•
adjustable wrench
safety glasses
Teflon® tape
center punch
1/4-inch & 9/16 or 5/8-inch drill bits
file
CAUTION: Turn off water supply to head without cartridge if it must be left
unattended for an extended period of time.
NOTE:
•
For cold water use only.
•
Make certain that installation complies with all state and local laws and regulations.
•
T he contaminants or other substances removed or reduced by the selected cartridge
are not necessarily in your water.
Optional Materials
•
3" x 3" x 1/2" wood block
• 1/8-inch drill bit
After prolonged periods of non-use (such as during a vacation) it is recommended
that the system be flushed thoroughly. Let water run for 10 minutes before using.
•
The filter cartridges used with this system have a limited service life. Changes in
taste, odor, and/or flow of the water being filtered indicate that the cartridge should
be replaced.
•
•
•
•
•
•
•
The RV-EZ-1 is tested and certified by NSF International to NSF/ANSI Standard 42 for
the aesthetic reduction of Chlorine Taste and Odor and Nominal Particulate Class III.
The RV-EZ-3 is tested and certified by NSF International to NSF/ANSI Standard 42 for
the aesthetic reduction of Chlorine Taste and Odor and Nominal Particulate Class 1.
Standard 53 for the reduction of Cysts, Turbidity, Lead, Lindane and Atrazine.
The RV-EZ-4 is tested and certified by NSF International to NSF/ANSI Standard 42 for the
aesthetic reduction of Chlorine Taste and Odor, Chloramines and Nominal Particulate
Class 1. Standard 53 for the reduction of Cysts, Lead, Mercury, VOC, MTBE and Turbidity.
[email protected]
146155 Rev C 12/06
800-683-8353
www.FridgeFilters.com
[email protected]
800-683-8353
Installation
•
For standard installation on 1/2-inch-14 NPS threads (most common thread on RV kitchen faucets)
cold water line.
•
Please read all instructions and precautions before installing and using the RV-EZ water filter.
•
Numbered diagrams correspond with numbered steps.
1
C
1. Selecting the Faucet Location
B
NOTE: The drinking water faucet should be positioned with function, convenience and appearance in mind.
An adequate flat area is required to allow faucet base to rest securely. The faucet fits through a 9/16-inch
hole. Most sinks have pre-drilled 13⁄8" or 11⁄2" diameter holes that may be used for faucet installation.
If these pre-drilled holes cannot be used or are in an inconvenient location, it will be necessary to drill a
9/16-inch or 5/8-inch hole in the sink to accommodate the faucet.
A
WARNING: This procedure may generate dusts which can cause severe irritation if inhaled or
come in contact with the eyes. The use of safety glasses and respirator for this procedure is recommended.
CAUTION: DO NOT ATTEMPT TO DRILL THROUGH AN ALL-PORCELAIN SINK. If you have an all-porcelain
sink, mount the faucet in pre-drilled sprayer hole or drill through counter top next to sink.
CAUTION: When drilling through a counter top make sure the area below the drilled area is free of
wiring and piping. Make certain that you have ample room to make the proper connections to the bottom
of the faucet.
2
CAUTION: Do not drill through a counter top that is more than 1-inch thick.
CAUTION: Do not attempt to drill through a tiled, marble, granite or similar counter top. Consult a
plumber or the counter top manufacturer for advice or assistance.
A
A) Line bottom of sink with newspaper to prevent metal shavings, parts or tools from falling
down the drain.
C
B) Place masking tape over the area to be drilled to prevent scratches if drill bit slips.
B
C) Mark hole with center punch. Use a 1/4-inch drill bit for a pilot hole, then, using a 9/16-inch or
5/8-inch drill bit, drill a hole completely through the sink. Smooth rough edges with a file.
2. Mounting the Faucet
A) Insert spout A into faucet body
the faucet body.
B) Slide black rubber gasket
D
B
. Tighten by screwing the spout nut
C
D
onto the threads on
onto threaded faucet stem. Lower faucet stem through hole in sink.
E
C) Accessing the faucet from underneath the sink, slide metal washer E up the faucet stem,
followed by the white plastic stem nut F . Tighten with fingers to secure faucet to sink.
F
NOTE: Do not use pliers to tighten stem nut. Pliers may strip the threads of the faucet stem.
3. Installing the Water Supply Adapter
3
The supply adapter fits 1/2-inch-14 NPS supply threads.
A) Turn off cold water supply line.
B) Turn on the cold water faucet and allow all water to drain from line.
C) Disconnect cold water line from 1/2-inch-14 NPS threaded stub on bottom of main faucet.
NOTE: If it is too difficult to access the threaded stub on the bottom of the cold water faucet, see
Alternate Installation on page 4.
B
D
C
A
D) Apply Teflon® tape onto male threads of faucet stub and supply adapter. Screw the water supply
adapter to the threaded faucet stub as shown.
E) Using the nut that previously connected the cold water line to the faucet, screw the cold water line
to the male supply adapter threads. Hand tighten nut and snug with wrench.
E
4. Mounting the Filter System
A) Select a location under the sink to mount the filter assembly. Choose a location where the filter will
be easily accessible.
NOTE: Allow 11⁄2-inches (38 mm) clearance below housing or 12-inch (305 mm) below filter head
to enable filter cartridge changes.
Technical Support: 1-800-721-9243, Monday-Friday, 8:00 a.m. – 4:30 p.m., CST
[email protected]
800-683-8353
www.FridgeFilters.com
[email protected]
800-683-8353
NOTE: Filter head should be mounted in vertical position, use mounting bracket as a template to
mark screw locations. Mount filter head in marked location using screws.
4A
4B
Wood
Block
Cabinet Wall
CAUTION: Filter head should be mounted on a stud or firm surface. The mounting bracket will
support the weight of the filter and help prevent strain on the cold water line.
B) If filter assembly is mounted on a side wall next to drawers, remove drawers. Cabinet wall may
be too thin to support filter assembly. We recommend that a 3" x 3" x 1/2" wood block be used
on the back side of the cabinet to allow the screws to penetrate through the cabinet and into the
wood block. This will allow the filter assembly to be fully supported. Using the filter head assembly
as a template, drill two 1/4-inch holes in the side wall. Position the block of wood behind these
two holes and drill two 1/8-inch holes into the block. Use the two screws provided to mount filter
assembly head to side wall and on the block of wood.
5. C
onnecting the Supply Adapter
and Inlet of Filter
A) Determine the length of plastic tubing needed to connect the inlet (left) side of the filter with the
supply adapter. Be sure to allow enough tubing to prevent kinking and cut the tubing squarely.
Place a mark 5/8-inch (16 mm) from both ends of the tubing.
A
5
5/8"
(16mm)
5/8"
(16mm)
B) Wet tubing with water and insert into the supply adapter, 5/8-inch (16 mm) until mark is flush
with fitting.
C) Wet tubing with water and insert into the filter inlet, 5/8-inch (16 mm) until mark is flush with
fitting.
B
NOTE: Disconnecting the Tubing from the Quick-Connect Fittings. Routine maintenance and cartridge
replacement will not require that you disconnect the tubing from the filter system; however, tubing
may be quickly and easily removed from the fitting if necessary. First, turn off the water supply to
the filter. Open faucet, then press in the grey collar around the fitting while pulling the tubing with
your other hand.
6. Connecting the Faucet
CAUTION: Do not over-tighten compression nut. Use caution not to bend or crimp tubes
when securing.
5C
A) Determine the length of plastic tubing needed to connect the outlet (right) side of the filter with the
faucet. Cut the tubing squarely.
CAUTION: Do not bend or crimp tube when inserting.
B) Slide plastic compression nut A over tubing followed by the ferrule
oriented properly, then place insert C into the end of tubing.
B
Inlet
Outlet
Insert
, make sure the ferrule is
C) Push the tubing firmly into the end of the faucet stem D and hand-tighten the compression nut
onto threads until secure. Then tighten approximately 1/2 turn with a wrench.
7. Installing the Cartridge
Hold cartridge from the bottom when installing or changing the cartridge. Use caution not to scrape
knuckles on bracket when locking the cartridge into place. Line up the arrow on the cartridge with unlocked
padlock symbol on head. Insert cartridge and turn arrow to locked padlock symbol. See the diagrams in
Filter Cartridge Replacement on page 4.
6
ferrule
orientation
8. Putting the Filter into Operation
C
A) Turn on water supply valve. Check for leaks. If it leaks, see Troubleshooting.
B) Rotate handle of drinking water faucet counter-clockwise to “on” position. Allow water to run for
10 minutes to flush air and carbon fines (very fine black powder).
A
B
D
C) Check for leaks before leaving installation. If it leaks, see Troubleshooting.
Technical Support: 1-800-721-9243, Monday-Friday, 8:00 a.m. – 4:30 p.m., CST
[email protected]
800-683-8353
www.FridgeFilters.com
[email protected]
800-683-8353
Filter Cartridge Replacement
NOTE: It is recommended that the EZ-1 filter be replaced every year and the EZ-3/EZ-4 filters every 6
months, or when you notice a change in taste, odor, or flow of the water being filtered.
R2
1) Relieve Water Pressure
A) Turn off water supply to the filter and dispense water from drinking water faucet until water flow
stops to relieve pressure.
2) Remove Old Cartridge
NOTE: Place towel under the system to catch any water drips.
A) Turn arrow from locked to unlocked position.
B) Gently pull down to remove cartridge.
b
3) Install New Cartridge
A) Line up arrow with unlocked position on head and insert cartridge.
B) Turn to locked position.
C) Turn on water and check for leaks. If it leaks, see Troubleshooting.
D) Flush water through drinking water faucet for 10 minutes to remove carbon fines. Check for
leaks before leaving installation. If it leaks, see Troubleshooting.
a
R3
Alternate Installation
This alternate installation will require the purchase of additional fittings to be used with the water supply
adapter. It will be necessary to remove a section of the cold water line to the main faucet. This cold water
line is typically 1/2-inch inner diameter and 5/8-inch outer diameter plastic tubing. Adapter fittings for this
tubing can be either barb type (based on the inner diameter), or compression or quick connect (based on
the outer diameter).
a
See Illustration A for possible fitting combination. If barb fittings are used, hose clamps must accompany
them. If compression fittings are used, tube inserts should also be used. Always use Teflon® tape on all
male threaded connections.
b
Illustration A
Cold Water Line
Winterization
Hose Clamp
CAUTION: Manufacturer’s instructions for winterizing should be followed.
CAUTION: Do not winterize with cartridge installed in unit.
1) Remove filter cartridge. See steps one and two of the Filter Cartridge Replacement. (above)
2) Dispose of old cartridge.
Barb Adaptor
3) Lubricate o-rings on RV-BYP-EZ fitting with clean silicone grease.
Line to inlet of
filter head
CAUTION: Do not use petroleum jelly.
4) Install RV-BYP-EZ fitting by lining up the arrow on the fitting with the “unlocked” position on the
head.
Supply Adaptor
(included)
5) Turn fitting to the locked position.
6) Check for leaks.
Female/Female Adaptor
Summer Start-up
CAUTION: Do not remove RV-BYP-EZ fitting until the system has been thoroughly flushed.
NOTE: Always use a new filter cartridge when starting up for summer.
Barb Adaptor
1) Remove RV-BYP-EZ fitting.
2) Install new filter cartridge. Follow step three under Filter Cartridge Replacement. (above)
3) Store bypass fitting in a manner such that it will stay clean and be easy to locate when it is time to
winterize your RV.
Hose Clamp
Cold Water Line
Technical Support: 1-800-721-9243, Monday-Friday, 8:00 a.m. – 4:30 p.m., CST
[email protected]
800-683-8353
www.FridgeFilters.com
[email protected]
800-683-8353
Replacement Parts
Troubleshooting, continued
RV-EZ
...on supply adapter connection
1
head assembly
2
RC-EZ-1 filter cartridge Level 1 filtration
3
RC-EZ-3 filter cartridge Level 3 filtration
4
RC-EZ-4 filter cartridge Level 4 filtration
5
lead-free faucet
6
clear 1/4 inch tubing
7
RV-BYP bypass fitting
8
small parts pack
Contact your area retailer or local water treatment professional for replacement cartridge
pricing. For replacement parts, contact your nearest Culligan water filter retailer or call
1-888-777-7962.
Turn off water supply valve and turn on drinking water faucet to release pressure
in system.
1
Loosen leaking threaded fitting on supply adapter or pull out leaking tubing from fitting.
Inspect to see if plastic tubing is scratched or supply adapter was properly attached. If
tubing is scratched, cut off 1/2-inch to 5/8-inch and reinstall per Step Five: Connecting
the Supply Adapter and Inlet of Filter. Reconnect tubing or tighten compression nut with
fingers, then tighten nut snugly 1/2-turn with wrench. Turn on water supply valve and
check for leaks.
...on faucet/tubing connection
Turn off water supply valve and turn on drinking water faucet to release pressure.
Loosen and remove compression nut fitting on faucet stem. Check if tubing is cut
squarely. Make sure tubing is inserted firmly into end of faucet stem, then retighten
compression nut with fingers until secure, then tighten nut snugly 1/2-turn with wrench.
Turn on water supply valve, then close faucet and check for leaks.
NOTE: If leaks persist, or if there are other leaks on system, turn off water supply. Call
our Technical Support Department at 1-800-721-9243.
2
3
4
Performance Data
6
7
8
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the system. Systems
certified for cyst reduction may be used on disinfected waters that may contain
filterable cysts.
5
NOTE: Substances reduced are not necessarily in your water. Filter must be maintained
according to manufacturer’s instructions, including replacement of filter cartridges.
Troubleshooting
Model RV-EZ
Leaks:
...between head and cartridge
Important Notice: Read this performance data and compare the capabilities of this
system with your actual water treatment needs. It is recommended that, before
installing a water treatment system, you have your water supply tested to determine
your actual water treatment needs.
1) Turn off the water supply to the filter and dispense water from drinking water
faucet until water and airflow stops.
This system has been tested according to NSF/ANSI 42 and 53 for the reduction of the
substances listed below. The concentration of the indicated substances in water entering
the system was reduced to a concentration less than or equal to the permissible limit for
water leaving the system, as specified in NSF/ANSI 42 and 53
2) Remove cartridge and inspect o-rings to make sure they are in place and clean.
3) Install cartridge and turn on water supply. If it still leaks, contact Technical
Support at 1-800-721-9243 M-F 8:00 AM - 4:30 PM CST.
...from fittings
RC-EZ-1 Cartridges
Turn off water supply to the filter and turn on drinking water faucet to release pressure in
system. Press in the grey collar around the fitting while pulling the tubing with the other
hand. Check if tubing is cut squarely or scratched. If tubing is scratched or uneven, cut
off 1/2” to 5/8” and re-install per step five of the installation; connecting the supply
adapter and inlet of filter. Open the water supply valve, then close faucet and check for
leaks. If the leaks persist, or if there are other leaks on the unit, turn off the water supply
then call Technical Support at 1-800-721-9243.
This system has been tested according to NSF/ANSI 42 for the reduction of the
substances listed below. The concentration of the indicated substances in water entering
the system was reduced to a concentration less than or equal to the permissible limit for
water leaving the system, as specified in NSF/ANSI 42.
Influent Challenge
Concentration
Reduction
Requirements
Minimum Reduction
Average Reduction
Chlorine
2.0 mg/L±10%
≥50%
94.8%
97.4%
Particulates, Class III
5µm to <15µm
at least 10,000
particles/mL
≥85%
99.8%
99.5%
Substance
Standard 42
Flow Rate=0.5 gpm (1.89 Lpm) Capacity=3000 gallons (11,356 L) or 12 months
Testing was performed under standard laboratory conditions, actual performance may vary.
Technical Support: 1-800-721-9243, Monday-Friday, 8:00 a.m. – 4:30 p.m., CST
[email protected]
800-683-8353
www.FridgeFilters.com
[email protected]
800-683-8353
RC-EZ-3 Cartridges
Performance Data - cont.
This system has been tested according to NSF/ANSI 42 and 53 for the reduction of the
substances listed below. The concentration of the indicated substances in water entering
the system was reduced to a concentration less than or equal to the permissible limit for
water leaving the system, as specified in NSF/ANSI 42 and 53.
Organic Chemicals Included by Surrogate Testing:
Applies to RV-EZ-4 Only
Influent Challenge
Concentration
Substance
Maximum
Permissible Product
Water Concentration
Substance
Reduction
Requirements
Minimum
Reduction
Average
Reduction
Standard 42
Chlorine
2.0 mg/L±10%
Particulates, Class I
0.5µm to <1µm
at least 10,000
particles/mL
≥50%
≥85%
96.2%
99.8%
97.4%
99.9%
Standard 53
Cyst
Minimum 50,000/L
99.95%
Influent Challenge
Concentration mg/L
Maximum permissible product water
concentration mg/L
alachor
0.050
0.001
atrazine
0.100
0.003
benzene
0.081
0.001
carbofuran
0.190
0.001
carbon tetrachloride
0.078
0.0018
chlorobenzene
0.077
0.001
0.0002
99.95%
99.9%
chloropicrin
0.015
Turbidity
11 mg/L ± 1 NTU
0.5 NTU
96.4%
98.5%
2,4-D
0.110
0.0017
Lead (pH 6.5)
0.15 mg/L ± 10%
0.010 mg/L
99.3%
99.3%
dibromochloropropane (DBCP)
0.052
0.00002
Lead (pH 8.5)
0.15 mg/L ± 10%
0.010 mg/L
94.8%
98.3%
o-dichlorobenzene
0.080
0.001
Atrazine
0.009 mg/L ± 10%
0.003 mg/L
94.1%
94.1%
p-dichlorobenzene
0.040
0.001
Lindane
0.002 mg/L ± 10%
0.0002 mg/L
94.5%
98.2%
1,2-dichloroethane
0.088
0.0048
1,1-dichloroethylene
0.083
0.001
cis-1,2-dichloroethylene
0.170
0.0005
Flow Rate=0.5 gpm (1.89 Lpm) Capacity=500 gallons (1893 L) or 6 months
Testing was performed under standard laboratory conditions, actual performance may vary
RC-EZ-4 Cartridges
This system has been tested according to NSF/ANSI 42 and 53 for the reduction of the
substances listed below. The concentration of the indicated substances in water entering
the system was reduced to a concentration less than or equal to the permissible limit for
water leaving the system, as specified in NSF/ANSI 42 and 53.
Influent Challenge
Concentration
Substance
Maximum
Permissible Product
Water Concentration
Reduction
Requirements
Minimum
Reduction
2.0 mg/L±10%
3.0 mg/L ± 10%
Particulates, Class I
0.5µm to <1µm
at least 10,000
particles/mL
≥50%
0.5 mg/L
≥85%
96.2
97.6%
99.9%
97.0%
98.0%
0.015 ± 20%
Minimum 50,000/L
11 mg/L ± 1 NTU
0.15 mg/L ± 10%
0.15 mg/L ± 10%
0.006 mg/L ± 10%
0.006 mg/L ± 10%
0.300 mg/L ± 10%
0.005 mg/L
99.95%
0.5 NTU
0.010 mg/L
0.010 mg/L
0.002 mg/L
0.002 mg/L
0.015 mg/L
96.8%
99.95%
96.6%
99.3%
94.1%
96.7%
96.6%
99.8%
99.9%
96.9%
99.9%
98.0%
99.3%
99.3%
96.7%
96.6%
cis-1,3-dichloropropylene
0.079
0.001
dinoseb
0.170
0.0002
0.00059
endrin
0.053
ethylbenzene
0.088
0.001
ethylene dibromide (EDB)
0.044
0.00002
bromochloroacetonitrile
0.022
0.0005
dibromoacetonitrile
0.024
0.0006
dichloroacetonitrile
0.0096
0.0002
trichloracetonitrile
0.015
0.0003
1,1-dichloro-2-propanone
0.0072
0.0001
1,1,1-trichloro-2-propanone
0.0082
0.0003
0.25
0.00001
heptachlor epoxide
0.0107
0.0002
hexachlorobutadiene
0.044
0.001
hexachlorocyclopentadiene
0.060
0.000002
heptachlor
99.8%
Flow Rate = 0.5 gpm (1.89 Lpm); Capacity = 500 gallons (1893 L) or 6 months
Testing was performed under standard laboratory conditions, actual performance may vary.
Test Conditions:
Flow Rate = 0.5 gpm
Inlet Pressure = 60 psi (4.1 bar)
= 7.5 ± 1
pH = 68° F ± 5° F (20° C ± 2.5° C)
Temperature Operating Requirements:
Pressure Temperature Turbidity 0.001
0.001
haloketones (HK):
Standard 53
MTBE
Cysts
Turbidity
Lead (pH 6.5)
Lead (pH 8.5)
Mercury (pH 6.5)
Mercury (pH 8.5)
Chloroform (VOC
surrogate chemical)
0.086
0.080
haloacetonitriles (HAN):
Average
Reduction
Standard 42
Chlorine
Chloramines
trans-1,2-dichloroethylene
1,2-dichloropropane
= 30 - 100 psi (2.1 - 6.9 bar)
= 40° - 100° F (4.4° -37.7° C)
= 5 NTU Max
lindane
0.055
0.00001
methoxychlor
0.050
0.0001
pentachlorophenol
0.096
0.001
simazine
0.120
0.004
styrene
0.150
0.0005
1,1,2,2,-tetrachloroethane
0.081
0.001
tetrachloroethylene
0.081
0.001
toluene
0.078
0.001
2,4,5-TP (silvex)
0.270
0.0016
tribromoacetic acid
0.042
0.001
1,2,4-trichlorobenzene
0.160
0.0005
1,1,1-trichloroethane
0.084
0.0046
1,1,2-trichloroethane
0.150
0.0005
trichloroethylene
0.180
0.0010
0.300
0.015
0.070
0.001
trihalomethanes (includes):
chloroform (surrogate chemical)
bromoform
bromodichloromethane
WARNING: Do not use with water that is microbiologically unsafe or
unknown quality without adequate disinfection before or after the system.
NOTE: Substances reduced are not necessarily in your water. Filter must be
maintained according to manufacturer’s instructions, including replacement of
filter cartridges.
chlorodibromomethane
xylenes (total)
Technical Support: 1-800-721-9243, Monday-Friday, 8:00 a.m. – 4:30 p.m., CST
[email protected]
800-683-8353
www.FridgeFilters.com
[email protected]
800-683-8353
Limited Warranty
This limited warranty applies to the Filter Housings only. It does NOT apply to any disposable filter cartridge, which has a life expectancy that varies with the water being filtered. This limited warranty covers
defects in materials and workmanship only for two full years from original date of delivery. Culligan will replace any part which in Culligan’s opinion is defective, unless: (1) any part of the system has been
subjected to any type of tampering, alteration, or improper use after delivery, or (2) any part of the system has been repaired by anyone not approved by Culligan. Our obligation does not include the cost
of shipment of materials. Culligan is not responsible for damage in transit, and claims for such damage should be presented to the carrier by the customer.
This product has been designed solely for use as a housing for a disposable filter cartridge. It is NOT warranted against freezing, and neither this product nor its parts is warranted against defects or
deterioration caused by uses for which this product was not expressly intended.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, WHETHER ORAL OR ARISING BY USAGE OF TRADE OR COURSE OF DEALING, INCLUDING,
WITHOUT LIMITATION, ANY WARRANTIES OF FITNESS OR MERCHANTABILITY. THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY. IN NO EVENT SHALL CULLIGAN BE LIABLE FOR ANY
ANTICIPATED OR LOST PROFITS, INCIDENTAL DAMAGES, CONSEQUENTIAL CHARGES OR OTHER LOSSES, WHETHER BASED ON BREACH OF CONTRACT, TORTIOUS CONDUCT OR ANY OTHER THEORY, INCURRED
IN CONNECTION WITH THE PURCHASE, INSTALLATION, REPAIR OR OPERATION OF THE OPAQUE FILTER HOUSING. CULLIGAN DOES NOT AUTHORIZE ANYONE TO ASSUME FOR IT ANY LIABILITY OR MAKE ON ITS
BEHALF ANY ADDITIONAL WARRANTIES IN CONNECTION WITH THE OPAQUE FILTER HOUSING OR ANY PART THEREOF.
For servicing under this warranty, return any defective part to YOUR RETAILER within the two-year period referred to above.
IOWA RESIDENTS ONLY:
Store or seller’s name:
Address:
City:
State:
Zip:
Telephone:
Seller’s signature:
Customer’s signature:
Culligan International Company
One Culligan Parkway • Northbrook, Illinois 60062
www.culligan.com
www.culligan-store.com
Customer Service M-F 8:00 a.m. – 4:30 p.m. CST
Phone: 1-800-721-7360 • Fax: 1-800-721-7390
International: Phone (920) 457-2726 • Fax (920) 457-7366
e-mail: [email protected]
© 2006 Culligan International Company, Printed in U.S.A.
[email protected]
Date:
Sales & Marketing Correspondence
P.O. Box 1086 • Sheboygan, WI 53082-1086
Fax (920) 457-7366
e-mail: [email protected]
146155 Rev C 12/06
800-683-8353
www.FridgeFilters.com
">
