ECS 865-M7 (V1.1)
Preface
Copyright
This publication, including all photographs, illustrations and software, is protected under
international copyright laws, with all rights reserved. Neither this manual, nor any of the
material contained herein, may be reproduced without written consent of the author.
Version 1.0
Disclaimer
The information in this document is subject to change without notice. The manufacturer
makes no representations or warranties with respect to the contents hereof and specifically
disclaims any implied warranties of merchantability or fitness for any particular purpose.
The manufacturer reserves the right to revise this publication and to make changes from
time to time in the content hereof without obligation of the manufacturer to notify any
person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel Corporation.
Other product names used in this manual are the properties of their respective owners and
are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment onto an outlet on a circuit different from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interconnect cables and a shielded AC power cable must be employed with this
equipment to ensure compliance with the pertinent RF emission limits governing this
device. Changes or modifications not expressly approved by the system’s manufacturer
could void the user’s authority to operate the equipment.
Preface
ii
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the following
conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received, including interference that
may cause undesired operation.
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian Interference-causing
Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le
matériel brouilieur du Canada.
About the Manual
The manual consists of the following:
Chapter 1
Describes features of the motherboard.
Introducing the Motherboard
Go to
H
page 1
Describes installation of motherboard
components.
Chapter 2
Installing the Motherboard
Go to
H
page 7
Provides information on using the BIOS
Setup Utility.
Chapter 3
Using BIOS
Go to
H
page 31
Chapter 4
Describes the motherboard software
Using the Motherboard Software
Go to
Preface
H
page 53
iii
TABLE OF CONTENTS
Preface
i
Chapter 1
1
Introducing the Motherboard
1
Introduction................................................................................................1
Features.......................................................................................................2
Motherboard Components.......................................................................4
Chapter 2
7
Installing the Motherboard
7
Safety Precautions......................................................................................7
Choosing a Computer Case.......................................................................7
Installing the Motherboard in a Case......................................................7
Checking Jumper Settings.........................................................................8
Setting Jumpers..............................................................................8
Checking Jumper Settings..............................................................9
Jumper Settings..............................................................................9
Connecting Case Components...............................................................10
Front Panel Connector.................................................................11
Installing Hardware...................................................................................12
Installing the Processor...............................................................12
Installing Memory Modules.........................................................14
Installing a Hard Disk Drive/CD-ROM......................................16
Installing a Floppy Diskette Drive...............................................18
Installing Add-on Cards..............................................................19
Dual Monitor Installation (For Windows XP).............................23
Dual Monitor Installation (For Windows 2000).........................24
Connecting Optional Devices......................................................26
Connecting I/O Devices..........................................................................29
Chapter 3
31
Using BIOS
31
About the Setup Utility............................................................................31
The Standard Configuration........................................................31
Entering the Setup Utility..............................................................31
Updating the BIOS.......................................................................33
Using BIOS................................................................................................33
Standard CMOS Features...........................................................34
Advanced BIOS Features.............................................................36
iv
Advanced Chipset Features.........................................................39
Integrated Peripherals.................................................................41
Power Management Setup...........................................................46
PNP/PCI Configurations.............................................................48
PC Health Status..........................................................................49
Frequency/Voltage Control..........................................................50
Load Fail-Safe Defaults................................................................51
Load Optimized Defaults.............................................................51
Set Supervisor/User Password....................................................51
Save & Exit Setup Option.............................................................51
Exit Without Saving......................................................................52
53
Chapter 4
Using the Motherboard Software
53
About the Software CD-ROM................................................................53
Auto-installing under Windows 98/ME/2000/XP................................53
Running Setup..............................................................................54
Manual Installation..................................................................................56
Utility Software Reference.......................................................................56
Multi-Language Translation
1
Chapter 1
Introducing the Motherboard
Introduction
Thank you for choosing 865-M7 motherboard of great performance and with enhanced
function. 865-M7 motherboard carries a Micro-ATX form factor of 244 x 244 mm. This
motherboard is a high performance, enhanced function motherboard that supports LGA775
socket for the latest Intel Pentium 4/Celeron processors for high-end business or personal
desktop markets.
The motherboard incorporates the 865GV Northbridge (NB) and ICH5 Southbridge (SB)
chipsets. The Northbridge supports a Front Side Bus (FSB) frequency of 800/533MHz
using a scalable FSB VCC_CPU. The memory controller supports DDR memory DIMM
frequencies of 400/333/266MHz. It supports four DDR SDRAM up to maximum memory
of 4GB. DDR Maximum memory bandwidth of 3.2GB/s in single-channel mode (DDR400)
and 6.4GB/s in dual-channel mode (DDR400) are supported. One AGP Express slot is used
to installed an AGP graphics card that emulates the AGP function.
The ICH5 Southbridge supports three PCI slots which are PCI 2.3 compliant. This
motherboard accommodates eight USB 2.0 ports for serial transfers at 480Mb/s (four
ports at the rear I/O & two headers onboard). This motherboard complies with AC’97 2.3
CODEC and supports up to six channels of PCM audio output (full AC3 decode). Two
onboard IDE connectors support 4 IDE devices in ATA-100/66/33 mode. The Southbridge
integrates two Serial ATA host controllers that are SATA v1.0 compliant, supporting two
SATA ports with maximum transfer rate up to 150MB/s each. One optional CNR slot
allow users to insert CNR cards with Modem and Audio functionality.
There is an advanced full set of I/O ports in the rear panel, including PS/2 mouse and
keyboard connectors, COM1, LPT1, VGA port, and four USB ports, one optional 1394a
port, one optional LAN port, and audio jacks for microphone, line-in, and line-out. In
addition to its excellent performance and stability, the motherboard is highly suited for
surfing the Internet and for rich multimedia applications, including streaming video download and are ideal for workstations and high-end home use.
Introducing the Motherboard
2
Features
Processor
The 865-M7 uses an LGA775 type of Pentium 4 that carries the following features:
•
•
•
Accommodates the latest Intel P4/Celeron processors
Supports a system bus (FSB) of 800/533MHz
Supports “Hyper-Threading” technology CPU
“Hyper-Threading” technology enables the operating system into thinking it’s hooked
up to two processors, allowing two threads to be run in parallel, both on separate
“logical” processors within the same physical processor.
Chipset
Intel’s 865GV (GMCH) Northbridge (NB) and 82801EB (ICH5) Southbridge (SB) chipsets
are based on an innovative and scalable architecture with proven reliability and performance.
865GV (NB)
ICH5 (SB)
•
Supports P4/Celeron processors with data transfer rate up to 800/
533/400MHz
•
Supports DDR SDRAM at 400/333/266MHz
•
AGTL+Host Bus with Integrated Termination Supporting 32-Bits
Host Addressing
•
8-bits/66MHz 8X Hub Interface to the Intel ICH5
•
Provides an integrated graphics accelerator delivering cost-effective 3D, 2D and video capabilities.
•
Supports up to six PCI Masters fully compliant with PCI 2.3 specificaiton
at 33MHz
•
Supports 2 channels Ultra ATA 100 bus master IDE controllers
•
Supports two Serial ATA Host Controllers
•
Compliant with AC’97 v2.3 supporting 6 Channels of audio outputs
•
Supports eight USB 2.0 ports for serial transfers at 480Mb/s maximum
Memory
This memory controller can accommodate up to four 2.5V DIMM DDR SDRAM, supporting DDR400/333/266MHz with maximum memory size of 4GB capability.
Audio CODEC
•
16-bit Stereo full-duplex CODEC with 48KHz sampling rate
•
Compliant with AC’97 2.3 specifications
•
Supports double sampling rate (96KHz) of DVD audio playback
•
Support S/PDIF input and output function
•
Direct Sound 3DTM compatible
Introducing the Motherboard
3
Graphics
•
3D setup and render engine
•
2D/3D graphics enhancement
•
Video DVD/PV-VCR
•
High quality texture engine
•
Zone Rendering support
•
Video Overlay
Expansion Options
The motherboard comes with the following expansion options:
•
Three 32-bit PCI slots
•
One AGP Express slot
•
Two 7-pin SATA connectors
•
Two IDE connectors which support four IDE devices
•
One floppy disk drive interface
•
One optional CNR slot
The motherboard supports Ultra DMA bus mastering with transfer rates of 100/66
33MB/s.
Onboard LAN (optional)
•
•
•
•
Supports 10Mb/s and 100Mb/s N-Way Auto-negotiation operation
Half and Full Duplex
Supports Wake-on-LAN (WOL) function and remote wake-up
Supports Full Duplex Flow Control (IEEE 802.3x)
Integrated I/O
The motherboard has a full set of I/O ports and connectors:
•
Two PS/2 ports for mouse and keyboard
•
One serial port
•
One parallel port
•
Four USB ports
•
One VGA port
•
One LAN port (optional)
•
One 1394 port (optional)
•
Audio jacks for microphone, line-in and line-out
BIOS Firmware
This motherboard uses Award BIOS that enables users to configure many system
features including the following:
•
Power management
•
CPU parameters
•
CPU and memory timing
The firmware can also be used to set parameters for different processor clock speeds.
Some hardware specifications and software items are subject to change
without prior notice.
Introducing the Motherboard
4
Motherboard Components
Introducing the Motherboard
5
Table of Motherboard Components
LABEL
1 CPU Socket
2 CPU_FAN
3 DIMM1~DIMM4
4 IR1
5 FDD1
6 ATX1
7 IDE1
8 IDE2
9 SPK1
10 PWR_FAN
11 CLR_CMOS
12 SATA1~2
13 PANEL1
14 BIOS_WP
15 USB3-4
16 1394A2*
17 COM2
18 CNR1*
19 SPDIFO1
20 CD_IN
21 PCI1~PCI3
COMPONENT
LGA775 socket for P4/Celeron CPUs
CPU cooling fan connector
184-pin DDR SDRAM slots
Onboard infrared header
Floppy disk drive connector
Standard 20-pin ATX power connector
Primary IDE connector
Secondary IDE connector
Speaker header
Power cooling fan connector
Clear CMOS jumper
Serial ATA connectors
Front panel switch/LED header
BIOS flash protect jumper
Front Panel USB headers
Onboard 1394a header
Onboard serial port header
Communications Networking Riser slot
SPDIF out header
Analog audio input connector
32-bit add-on card slots
22 JP4
LAN Enable/Disable jumper
23 AGP1
24 AUDIO1
AGP Express slot
Front panel audio header
25 SYS_FAN
Case cooling fan connector
26 ATX12V
4-pin +12V power connector
“*” stands for optional components.
This concludes Chapter 1. The next chapter explains how to install the motherboard.
Introducing the Motherboard
6
Memo
Introducing the Motherboard
7
Chapter 2
Installing the Motherboard
Safety Precautions
•
•
•
•
•
Follow these safety precautions when installing the motherboard
Wear a grounding strap attached to a grounded device to avoid damage from
static electricity
Discharge static electricity by touching the metal case of a safely grounded
object before working on the motherboard
Leave components in the static-proof bags they came in
Hold all circuit boards by the edges. Do not bend circuit boards
Choosing a Computer Case
There are many types of computer cases on the market. The motherboard complies with
the specifications for the Micro-ATX system case. First, some features on the motherboard
are implemented by cabling connectors on the motherboard to indicators and switches on
the system case. Make sure that your case supports all the features required. Secondly, 865M7 supports one or two floppy diskette drives and four enhanced IDE drives. Make sure
that your case has sufficient power and space for all drives that you intend to install.
Most cases have a choice of I/O templates in the rear panel. Make sure that the I/O
template in the case matches the I/O ports installed on the rear edge of the motherboard.
This motherboard carries a Micro-ATX form factor of 244 x 244 mm. Choose a case that
accommodates this form factor.
Installing the Motherboard in a Case
Refer to the following illustration and instructions for installing the motherboard in a case.
Most system cases have mounting brackets installed in the case, which correspond the holes
in the motherboard. Place the motherboard over the mounting brackets and secure the
motherboard onto the mounting brackets with screws.
Ensure that your case has an I/O template that supports the I/O ports and expansion slots
on your motherboard.
Installing the Motherboard
8
Do not over-tighten the screws as this can stress the motherboard.
Checking Jumper Settings
This section explains how to set jumpers for correct configuration of the motherboard.
Setting Jumpers
Use the motherboard jumpers to set system configuration options. Jumpers with more than
one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on
the correct pins.
The illustrations show a 2-pin jumper. When
the jumper cap is placed on both pins, the
jumper is SHORT. If you remove the jumper
cap, or place the jumper cap on just one pin,
the jumper is OPEN.
SHORT
This illustration shows a 3-pin jumper. Pins
1 and 2 are SHORT
Installing the Motherboard
OPEN
9
Checking Jumper Settings
The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled.
Jumper Settings
Jumper
Type
Description
Setting (default)
1-2: NORMAL
2-3: CLEAR
CLR_CMOS 3-pin
CLEAR CMOS
BIOS_WP 2-pin
BIOS PROTECT
Clear CMOS
1
Before clearing the CMOS,
make sure to turn off the system.
OPEN:
DISABLE
BIOS_WP
1
SHORT: ENABLE
JP4
JP4
3-pin
LAN FUNCTION
1-2: ENABLE
2-3: DISABLE
Installing the Motherboard
1
10
Connecting Case Components
After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following:
1
2
3
3
4
5
6
Connect the CPU cooling fan cable to CPU_FAN.
Connect the case cooling fan connector to SYS_FAN.
Connect the power cooling fan connector to PWR_FAN.
Connect the case speaker cable to SPK1.
Connect the case switches and indicator LEDs to the PANEL1.
Connect the standard power supply connector to ATX1.
Connect the auxiliary case power supply connector to ATX12V.
CPUFAN1: FAN Power Connectors
Pin
Signal Name
Function
1
2
3
GND
Sense
System Ground
Power +12V
Sensor
4
PWM
CPU FAN control
+12V
Users please note that the fan connector supports the CPU cooling
fan of 1.1A~2.2A (26.4W max.) at +12V.
SYS_FAN/PWR_FAN: FAN Power Connectors
Pin
Signal Name
Function
1
GND
System Ground
2
3
+12V
Power +12V
Sensor
Sense
Installing the Motherboard
11
SPK1: Internal speaker
Pin
Signal Name
Signal
1
2
3
Key
Ground
4
VCC
ATX1: ATX 20-pin Power Connector
Pin
Signal Name
Pin
Signal Name
1
2
+3.3V
+3.3V
+3.3V
11
12
3
Ground
13
Ground
4
+5V
14
PS ON#
5
6
7
8
9
10
Ground
+5V
Ground
15
16
17
18
19
20
Ground
Ground
Ground
PWRGD
+5VSB
+12V
-12V
-5V
+5V
+5V
ATX12V: ATX 12V Power Connector
Pin
Signal Name
Ground
1
2
3
4
Ground
+12V
+12V
Front Panel Header
The front panel header (PANEL1) provides a standard set of switch and LED headers
commonly found on ATX or micro-ATX cases. Refer to the table below for information:
Pin Signal Name
Function
Pin Signal Name
Function
Hard disk LED(+) 2
FP PWR/SLP
*MSG LED(+)
HD_LED_N Hard disk LED(-)
RST_SW_N Reset Switch(-)
RST_SW_P Reset Switch(+)
4
6
8
FP PWR/SLP
PWR_SW_P
PWR_SW_N
*MSG LED(-)
Power Switch(+)
Power Switch(-)
RSVD
10 Key
1
HD_LED_P
3
5
7
9
Reserved
No pin
* MSG LED (dual color or single color)
Hard Drive Activity LED
Connecting pins 1 and 3 to a front panel mounted LED provides visual indication that data
is being read from or written to the hard drive. For the LED to function properly, an IDE
drive should be connected to the onboard IDE interface. The LED will also show activity
for devices connected to the SCSI (hard drive activity LED) connector.
Installing the Motherboard
12
Power/Sleep/Message waiting LED
Connecting pins 2 and 4 to a single or dual-color, front panel mounted LED provides power
on/off, sleep, and message waiting indication.
Reset Switch
Supporting the reset function requires connecting pin 5 and 7 to a momentary-contact
switch that is normally open. When the switch is closed, the board resets and runs POST.
Power Switch
Supporting the power on/off function requires connecting pins 6 and 8 to a momentarycontact switch that is normally open. The switch should maintain contact for at least 50 ms
to signal the power supply to switch on or off. The time requirement is due to internal debounce circuitry. After receiving a power on/off signal, at least two seconds elapses before
the power supply recognizes another on/off signal.
Installing Hardware
Installing the Processor
Caution: When installing a CPU heatsink and cooling fan make sure that
you DO NOT scratch the motherboard or any of the surface-mount
resistors with the clip of the cooling fan. If the clip of the cooling fan
scrapes across the motherboard, you may cause serious damage to the
motherboard or its components.
On most motherboards, there are small surface-mount resistors near the
processor socket, which may be damaged if the cooling fan is carelessly
installed.
Avoid using cooling fans with sharp edges on the fan casing and the
clips. Also, install the cooling fan in a well-lit work area so that you can
clearly see the motherboard and processor socket.
Before installing the Processor
This motherboard automatically determines the CPU clock frequency and system bus
frequency for the processor. You may be able to change these settings by making changes
to jumpers on the motherboard, or changing the settings in the system Setup Utility. We
strongly recommend that you do not over-clock processors or other components to run
faster than their rated speed.
Warning: Over-clocking components can adversely affect the reliability of
the system and introduce errors into your system. Over-clocking can
permanently damage the motherboard by generating excess heat in
components that are run beyond the rated limits.
This motherboard has an LGA775 processor socket. When choosing a processor, consider
the performance requirements of the system. Performance is based on the processor design,
the clock speed and system bus frequency of the processor, and the quantity of internal
cache memory and external cache memory.
Installing the Motherboard
13
CPU Installation Procedure
The following illustration shows CPU installation components.
A. Unload the cap
· Use thumb & forefinger to hold the
lifting tab of the cap.
· Lift the cap up and remove the cap
completely from the socket.
B. Open the load plate
· Use thumb & forefinger to hold the
hook of the lever, pushing down and pulling
aside unlock it.
· Lift up the lever.
· Use thumb to open the load plate. Be
careful not to touch the contacts.
C. Install the CPU on the socket
· Orientate CPU package to the socket.
Make sure you match triangle marker
to pin 1 location.
D. Close the load plate
· Slightly push down the load plate onto the
tongue side, and hook the lever.
· CPU is locked completely.
E. Apply thermal grease on top of the CPU.
F.
Fasten the cooling fan supporting base onto
the CPU socket on the motherboard.
G. Make sure the CPU fan is plugged to the
CPU fan connector. Please refer to the CPU
cooling fan user’s manual for more detail
installation procedure.
To achieve better airflow rates and heat dissipation, we suggest that you use
a high quality fan with 3800 rpm at least. CPU fan and heatsink installation procedures may vary with the type of CPU fan/heatsink supplied. The
form and size of fan/heatsink may also vary.
Installing the Motherboard
14
Installing Memory Modules
865-M7 accommodates four 184-pin 2.5V unbuffered Double Data Rate (DDR) SDRAM
(Synchronous Dynamic Random Access Memory) memory modules, and supports up to
DDR400/333/266. Each module can be installed with 1GB of memory, the total maximum
memory size is 4GB.
DDR SDRAM memory module table
Memory module
DDR266
Memory Bus
133MHz
DDR333
166MHz
DDR400
200MHz
Do not remove any memory module from its antistatic packaging until
you are ready to install it on the motherboard. Handle the modules only
by their edges. Do not touch the components or metal parts. Always wear
a grounding strap when you handle the modules.
Installation Procedure
Refer to the following to install the memory modules.
1
2
3
4
5
6
This motherboard supports unbuffered DDR SDRAM only.
Push the latches on each side of the DIMM slot down.
Align the memory module with the slot. The DIMM slots are
keyed with notches and the DIMMs are keyed with cutouts so that
they can only be installed correctly.
Check that the cutouts on the DIMM module edge connector
match the notches in the DIMM slot.
Install the DIMM module into the slot and press it firmly down
until it seats correctly. The slot latches are levered upwards and
latch on to the edges of the DIMM.
Install any remaining DIMM modules.
Installing the Motherboard
15
Table A: DDR (memory module) QVL (Qualified Vendor List)
The following DDR400 memory modules have been tested and qualified for use with this
motherboard.
Size
Vendor
Module Name
128MB
Infineon
HYS64D16301GU-5-B
NANYA
NT128D64SH4B1G-5T
Infineon
HYS64D32300GU-5-B
Infineon
HYS64D32300HU-5-C
Micron
MT16VDDT3264AG-403B2
Micron
MT8VDDT3264AG-40BC4
256MB
512MB
NANYA
NT256D64S88B1G-5T
SAMSUNG
M368L3223DTM-CC4
Infineon
HYS64D64320HU-5-C
Micron
MT16VDDT6464AG-40BC4
NANYA
NT512D64S8HB1G-5T
SAMSUNG
M368L6423DTM-CC4
SAMSUNG
M368L6423ETM-CCC
Installing the Motherboard
16
Installing a Hard Disk Drive/CD-ROM
This section describes how to install IDE devices such as a hard disk drive and a CD-ROM
drive.
About IDE Devices
Your motherboard has a primary and secondary IDE channel interface (IDE1 and IDE2).
An IDE ribbon cable supporting two IDE devices is bundled with the motherboard.
You must orient the cable connector so that the pin1 (color) edge of the
cable correspoinds to the pin 1 of the I/O port connector.
IDE1: Primary IDE Connector
The first hard drive should always be connected to IDE1.
IDE2: Secondary IDE Connector
The second drive on this controller must be set to slave mode. The cinfiguration is the same
as IDE1.
IDE devices enclose jumpers or switches used to set the IDE device as MASTER or SLAVE.
Refer to the IDE device user’s manual. Installing two IDE devices on one cable, ensure that
one device is set to MASTER and the other device is set to SLAVE. The documentation of
your IDE device explains how to do this.
About UltraDMA
This motherboard supports UltraDMA 100/66/33. UDMA is a technology that accelerates
the performance of devices in the IDE channel. To maximize performance, install IDE
devices that support UDMA and use 80-pin IDE cables that support UDMA 100/66.
Installing the Motherboard
17
About SATA Connectors
Your motherboard features two SATA connectors supporting a total of two drives. SATA , or
Serial ATA (Advanced Technology Attachment) is the standard interface for the IDE hard
drives which are currently used in most PCs. These connectors are well designed and will
only fit in one orientation. Locate the SATA connectors on the motherboard and follow the
illustration below to install the SATA hard drives.
Installing Serial ATA Hard Drives
To install the Serial ATA (SATA) hard drives, use the SATA cable that supports the Serial
ATA protocol. This SATA cable comes with an SATA power cable. You can connect either
end of the SATA cable to the SATA hard drive or the connector on the motherboard.
SATA cable
Refer to
1
2
3
(optional)
SATA power cable
(optional)
the illustration below for proper installation:
Attach either cable end to the connector on the motherboard.
Attach the other cable end to the SATA hard drive.
Attach the SATA power cable to the SATA hard drive and connect the other
end to the power supply.
This motherboard does not support the “Hot-Plug” function.
Installing the Motherboard
18
Installing a Floppy Diskette Drive
The motherboard has a floppy diskette drive (FDD) interface and ships with a diskette drive
ribbon cable that supports one or two floppy diskette drives. You can install a 5.25-inch
drive and a 3.5-inch drive with various capacities. The floppy diskette drive cable has one
type of connector for a 5.25-inch drive and another type of connector for a 3.5-inch drive.
You must orient the cable connector so that the pin 1 (color) edge of the
cable corresponds to the pin 1 of the I/O port connector.
FDD1: Floppy Disk Connector
This connector supports the provided floppy
drive ribbon cable. After connecting the single
end to the onboard floppy connector, connect
the remaining plugs on the other end to the
floppy drives correspondingly.
Installing the Motherboard
19
Installing Add-on Cards
The slots on this motherboard are designed to hold expansion cards and connect them to the
system bus. Expansion slots are a means of adding or enhancing the motherboard’s features
and capabilities. With these efficient facilities, you can increase the motherboard’s capabilities by adding hardware that performs tasks that are not part of the basic system.
AGP Express The AGP Express slot is used to install a graphics adapter that emulates
Slot
the AGP function. In order to get better performance and compability on
our special design AGP Express slot, we recommend users use one of the
AGP graphics cards that have been tested by our company. Please refer to
page 21 for the “supported list”.
PCI Slot
This motherboard is equipped with three standard PCI slots. PCI stands
for Peripheral Component Interconnect and is a bus standard for expansion cards, which for the most part, is a supplement of the older ISA bus
standard. The PCI slots on this board are PCI v2.3 compliant.
CNR1 Slot
(optional)
This slot is used to insert CNR cards with Modem and Audio functionality.
Before installing an add-on card, check the documentation for the card
carefully. If the card is not Plug and Play, you may have to manually
configure the card before installation.
Installing the Motherboard
20
Follow these instructions to install an add-on card:
1
2
3
Remove a blanking plate from the system case corresponding to the slot you
are going to use.
Install the edge connector of the add-on card into the expansion slot. Ensure
that the edge connector is correctly seated in the slot.
Secure the metal bracket of the card to the system case with a screw.
For some add-on cards, for example graphics adapters and network adapters, you have to install drivers and software before you can begin using the
add-on card.
Installing the Motherboard
21
Table A: Supported List of AGP Express Slot
The following VGA chipsets have been tested and qualified for use with this motherboard.
VGA
Chip
Model name
GAWWARD Geforce3 TI200 128MB
Leadtek A250TDT TI4400 128MB
Leadtek WinFast A250 LE TD GF4 TI4200 64MB
BiTC GeForce4 MX440 64MB
Gigabyte GeForce FX5700U 128MB
NVIDIA Leadtek WinFast A350 GeForce FX5900-TDH 256MB
Leadtek WinFast A380 GeForce FX5950 Ultra TDM 256MB
Leadtek WinFast A280 LE TD GF4 TI4200 128MB
MSI GeForce FX5800-TD 128MB
Millennium Silver TI4600 128MB
Triplex GeForce FX5200 64MB
ATI R7000 64MB
ATI R7500 64MB
ATI ATI R9000 128MB
ATI Radeon 9500 64MB
ATI Radeon 9700PRO 128MB
ECS R9200LE-64T
AGP
4X/8X
4X
8X
4X
For the latest supported AGP graphics list, please visit our website:
www.ecs.com.tw/ECSWeb/Support/agp.aspx
Installing the Motherboard
22
Once the AGP VGA card is properly installed under Windows 2000 or Windows XP, the
below picture will be shown. And users will see the icon
if the driver is not well-installed
in the system.
1. It is normal to see the icon
as the onboard VGA card is “Disabled”.
2. To install the system with an add-on AGP VGA card, users must make
sure to install the driver of add-on AGP VGA card before you install
the onboard VGA driver. If the onboard VGA driver has already been
installed before you install the add-on AGP VGA card, the system will
set the onboard VGA as the primary graphics adapter automatically. In
this situation, if you want to install the add-on AGP VGA card, you
need to remove the onboard VGA driver first, then install the add-on AGP
VGA card and its driver, or it will “no display” when your monitor connects to AGP VGA card.
3. Please note that if both of the the onboard VGA and the AGP Express Slot
are connected to the monitors, the system will set the AGP Express slot as
the primary graphics adapter automatically, and the onboard VGA will
be functionless.
Installing the Motherboard
23
Dual Monitor
In order to enable “Dual Monitor” Function, users must have “Two Monitors”, “Two
Graphics Devices” (one is for AGP VGA card; the other one is for onboard VGA) and
Windows 2000 or Windows XP that supports the Dual Monitor Function. Users must
follow the “Dual Monitor Installation” shown as below.
Dual Monitor Installation (For Windows XP)
If the onboard VGA is already installed, and you want to use the add-on AGP VGA card, you
may follow the installation step 1-6 as the following.
However, users may go to Step 4 directly if the add-on AGP VGA card is already installed;
then turned on the onboard VGA devies for “secondary display”.
Step 1: Remove the Onboard VGA Driver
Go to “Control Panel”
Choose “Add or Remove Programs”
Choose “Intel ® Extreme Graphics Driver”
Click “Remove”
Shut down the computer
Step 2: Install the Add-on AGP VGA Card
Shut down the system
Install the add-on AGP VGA card in the AGP Express slot
Turn on the computer
When you turn on the system, windows might report Found New Hardware
Wizard, “Video Controller (VGA Compatible)” or “Video Controller”. When
you see the Found New Hardware Wizard dialogue box, DO NOT insert any
disk in your CD/DCD ROM before clicking on the “Next” button. The Windows Auto-search will not be finished till it can’t search the related driver.
Step 3: Install the Add-on AGP VGA Card Driver
Install the add-on AGP VGA Card driver
Restart the computer
Step 4: Install the Onboard VGA Driver
Install the onboard VGA driver from our support CD to utilize Dual Monitor
Function. Please refer to the follow path.
CD-ROM:\VGA\Intel845_865\Win2K&XP\Graphics\Setup.exe
Restart the computer.
If the add-on AGP VGA card driver and onboard VGA drivers are installed,
the dual-monitor display will be enabled. As soon as it is enabled, follow the
instructions to view the status of the dual-monitor display or adjust the parameters of the two monitors.
Installing the Motherboard
24
Step 5: Right click the desktop. Select “Properties” as shown in the below.
Step 6: Select “Display Properties”. Click “Settings”
Then the parameters of the two minitors can be adjusted.
Dual Monitor Installation (For Windows 2000)
If the onboard VGA is already installed, and you want to use the add-on AGP VGA card, you
may follow the installation step 1-6 as the following.
However, users may go to Step 4 directly if the add-on AGP VGA card is already installed;
then turned on the onboard VGA devies for “secondary display”.
Step 1: Install the Add-on AGP VGA Card
Shut down the system
Install your add-on AGP VGA card in the AGP Express slot
Turn on the computer
Step 2: Install the Add-on AGP VGA Card Driver
Install the add-on AGP VGA card driver
Restart the computer
Windows might report Found New Hardware Wizard once the system is
turned on. When you see the Found New Hardware Wizard dialogue
box, please click on “Cancel” and DO NOT install the onboard VGA
driver.
Step 3: Remove the Onboard VGA Driver
Go to “Control Panel”
Choose “Add or Remove Programs”
Choose “Intel
®
Extreme Graphics Driver”
Click “Remove” and Restart the computer
When you turn on the system, windows might report Found New Hardware
Wizard, “Video Controller (VGA Compatible)” or “Video Controller”.
When you see the Found New Hardware Wizard dialogue box, DO NOT
insert any disk in your CD/DVD-ROM before clicking on the “Next” button.
The Windows Auto-search will not be finished until it can’t search the
related driver.
Installing the Motherboard
25
Step 4: Install the Onboard VGA Driver
Install the Onboard VGA driver from our support CD to utilize Dual Monitor
Function. Please refer to the below path.
CD-ROM:\VGA\Intel845_865\Win2K&XP\Graphics\Setup.exe
Restart the computer
If the add-on AGP VGA card driver and onboard VGA drivers are installed, the dual-monitor display will be enabled. As sonn as it is enabled,
follow the instructions to view the status of the dual-monitor display or
adjust the parameters of the two monitors.
Step 5: Right clock the desktop. Select “Properties” as shown in the below.
Step 6: Select “Display Properties”, then click “Settings”.
Then the parameters of the two monitors can be adjusted.
Installing the Motherboard
26
Connecting Optional Devices
Refer to the following for information on connecting the motherboard’s optional devices:
SPDIFO1: SPDIF out header
This is an optional header that provides an S/PDIF (Sony/Philips Digital Interface) output
to digital multimedia device through optical fiber or coaxial connector.
Pin
1
2
3
4
Signal Name
Function
SPDIF digital output
5V analog Power
No pin
Ground
SPDIF
+5VA
Key
GND
AUDIO1: Front Panel Audio header
This header allows the user to install auxiliary front-oriented microphone
and line-out ports for easier access.
Pin
Pin
Signal Name
Signal Name
Function
1
2
3
4
5
6
7
AUD_MIC
Front Panel Microphone input signal
AUD_GND
Ground used by Analog Audio Circuits
8
9
10
Key
No Pin
AUD_F_L
Left Channel Audio signal to Front Panel
AUD_RET_L
Left Channel Audio signal to Return from Front Panel
AUD_MIC_BIAS Microphone Power
AUD_VCC
Filtered +5V used by Analog Audio Circuits
AUD_F_R
Right Channel audio signal to Front Panel
AUD_RET_R
RightChannelAudiosignaltoReturnfromFrontPanel
REVD
Reserved
Installing the Motherboard
27
USB3/4: Front Panel USB headers
The motherboard has four USB ports installed on the rear edge I/O port array. Additionally,
some computer cases have USB ports at the front of the case. If you have this kind of case,
use auxiliary USB connector to connect the front-mounted ports to the motherboard.
Pin
Signal Name
Function
1
2
3
4
5
6
7
USBPWR
Front Panel USB Power
USBPWR
Front Panel USB Power
USB_FP_P0-
USB Port 0 Negative Signal
USB_FP_P1-
USB Port 1 Negative Signal
USB_FP_P0+
USB Port 0 Positive Signal
USB_FP_P1+
USB Port 1 Positive Signal
GND
Ground
8
9
10
GND
Ground
Key
No pin
USB_FP_OC0
Overcurrent Signal
Please make sure that the USB cable has the same pin assignment as
indicated above. A different pin assignment may cause damage or system
hang-up.
SATA1/2: Serial ATA connectors
These connectors are use to support the new Serial ATA devices for the highest date transfer
rates (150 MB/s), simpler disk drive cabling and easier PC assembly. It eliminates limitations
of the current Parallel ATA interface. But maintains register compatibility and software
compatibility with Parallel ATA.
Pin
Pin
1
3
5
7
Signal Name
Signal Name
Ground
Pin
2
4
6
-
TXRXGround
Signal Name
Function
TX+
Ground
RX+
-
COM2: Onboard serial port header
Connect a serial port extension bracket to this header to add a second serial port to your
system.
Pin
Signal Name
1
2
3
4
5
6
7
NDCDB
8
9
10
Function
Data carry detect
NSINB
Serial Data In
NSOUTB
Serail Data Out
NDTRB
Data terminal ready
GND
Ground
NDSRB
Date set ready
NRTSB
Request to send
NCTSB
Clear to send
NRIB
Ring Indicator
KEY
Key
Installing the Motherboard
28
IR1: Infrared header
The mainboard supports an Infrared (IR1) data port. Infrared ports allow the wireless
exchange of information between your computer and similarly equipped devices such as
printers, laptops, Personal Digital Assistants (PDAs), and other computers.
Pin
Signal Name
Function
1
Not Assigned
2
Key
No pin
3
+5V
IR Power
4
GND
Ground
5
IRTX
IrDA serial output
6
IRTX
IrDA serial input
Not assigned
CD_IN: Analog Audio Input header
Pin
1
2
3
4
Signal Name
Function
CD in_L
CD In left channel
Ground
Ground
CD In right channel
GND
GND
CD in_R
1394A2: Onboard IEEE 1394a header (optional)
Connect this header to any device with IEEE 1394a interface.
Pin
Pin
1
3
5
7
9
Signal Name
Signal Name
TPA+
GND
TPB+
Cable-Power
Key Pin
Pin
2
4
6
8
10
Signal Name
Function
TPAGND
TPBCable-Power
GND
Installing the Motherboard
29
Connecting I/O Devices
The backplane of the motherboard has the following I/O ports:
(optional)
PS2 Mouse
Use the upper PS/2 port to connect a PS/2 pointing device.
PS2 Keyboard
Use the lower PS/2 port to connect a PS/2 keyboard.
Parallel Port (LPT1)
Use LPT1 to connect printers or other parallel communications
devices.
Serial Port (COM1)
Use the COM port to connect serial devices such as mice or fax/
modems. COM1 is identified by the system as COM1/3.
VGA Port
Connect your monitor to the VGA port.
LAN Port (optional)
Connect an RJ-45 jack to the LAN port to connect your computer to the Network.
USB Ports
Use the USB ports to connect USB devices.
1394 Port (optional)
Connect your 1394a device to any device with Firewire interface.
Audio Ports
Use the three audio ports to connect audio devices. The first
jack is for stereo line-in signal. The second jack is for stereo
line-out signal. The third jack is for microphone.
This concludes Chapter 2. The next chapter covers the BIOS.
Installing the Motherboard
30
Memo
Installing the Motherboard
31
Chapter 3
Using BIOS
About the Setup Utility
The computer uses the latest Award BIOS with support for Windows Plug and Play. The
CMOS chip on the motherboard contains the ROM setup instructions for configuring the
motherboard BIOS.
The BIOS (Basic Input and Output System) Setup Utility displays the system’s configuration status and provides you with options to set system parameters. The parameters are
stored in battery-backed-up CMOS RAM that saves this information when the power is
turned off. When the system is turned back on, the system is configured with the values you
stored in CMOS.
The BIOS Setup Utility enables you to configure:
•
Hard drives, diskette drives and peripherals
•
Video display type and display options
•
Password protection from unauthorized use
•
Power Management features
The settings made in the Setup Utility affect how the computer performs. Before using the
Setup Utility, ensure that you understand the Setup Utility options.
This chapter provides explanations for Setup Utility options.
The Standard Configuration
A standard configuration has already been set in the Setup Utility. However, we recommend
that you read this chapter in case you need to make any changes in the future.
This Setup Utility should be used:
•
when changing the system configuration
•
when a configuration error is detected and you are prompted to make changes
to the Setup Utility
•
when trying to resolve IRQ conflicts
•
when making changes to the Power Management configuration
•
when changing the password or making other changes to the Security Setup
Entering the Setup Utility
When you power on the system, BIOS enters the Power-On Self Test (POST) routines.
POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are
completed, the following message appears:
Using BIOS
32
Press DEL to enter SETUP
Pressing the delete key accesses the BIOS Setup Utility:
Phoenix-AwardBIOS CMOS Setup Utility:
f Standard CMOS Features
f Advanced BIOS Features
f Advanced Chipset Features
f Integrated Peripherals
fPower Management Setup
f PnP/PCI Configurations
f PC Health Status
fFrequency Control
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
mnlk
Esc: Quit
F10: Save & Exit Setup
: Select Item
Time, Date, Hard Disk Type...
BIOS Navigation Keys
The BIOS navigation keys are listed below:
KEY
ESC
FUNCTION
Exits the current menu
oqrt
Scrolls through the items on a menu
+/-/PU/PD
Modifies the selected field’s values
F10
Saves the current configuration and exits setup
F1
Displays a screen that describes all key functions
F5
Loads previously saved values to CMOS
F6
Loads a minimum configuration for troubleshooting
F7
Loads an optimum set of values for peak performance
Using BIOS
33
Updating the BIOS
You can download and install updated BIOS for this motherboard from the manufacturer’s
Web site. New BIOS provides support for new peripherals, improvements in performance,
or fixes for known bugs. Install new BIOS as follows:
1
If your motherboard has a BIOS protection jumper, change the setting to allow
BIOS flashing.
2
If your motherboard has an item called Firmware Write Protect in Advanced
BIOS features, disable it. (Firmware Write Protect prevents BIOS from being
overwritten.
3
Create a bootable system disk. (Refer to Windows online help for information
on creating a bootable system disk.)
4
Download the Flash Utility and new BIOS file from the manufacturer’s Web
site. Copy these files to the system diskette you created in Step 3.
5
Turn off your computer and insert the system diskette in your computer’s
diskette drive. (You might need to run the Setup Utility and change the boot
priority items on the Advanced BIOS Features Setup page, to force your
computer to boot from the floppy diskette drive first.)
6
At the A:\ prompt, type the Flash Utility program name and press <Enter>.
7
Type the filename of the new BIOS in the “File Name to Program” text box.
Follow the onscreen directions to update the motherboard BIOS.
8
When the installation is complete, remove the floppy diskette from the diskette
drive and restart your computer. If your motherboard has a Flash BIOS jumper,
reset the jumper to protect the newly installed BIOS from being overwritten.
Using BIOS
When you start the Setup Utility, the main menu appears. The main menu of the Setup
Utility displays a list of the options that are available. A highlight indicates which option is
currently selected. Use the cursor arrow keys to move the highlight to other options. When
an option is highlighted, execute the option by pressing <Enter>.
Some options lead to pop-up dialog boxes that prompt you to verify that you wish to
execute that option. Other options lead to dialog boxes that prompt you for information.
Some options (marked with a triangle f ) lead to submenus that enable you to change the
values for the option. Use the cursor arrow keys to scroll through the items in the submenu.
In this manual, default values are enclosed in parenthesis. Submenu items are denoted by a
triangle f .
Using BIOS
34
Standard CMOS Features
This option displays basic information about your system.
Phoenix-AwardBIOS CMOS Setup Utility
Standard CMOS Features
f
f
f
f
Date (mm:dd:yy)
Time (hh:mm:ss)
IDE Channel 0 Master
IDE Channel 0 Slave
IDE Channel 1 Master
IDE Channel 1 Slave
Mon, Sep 17 2004
13 : 4 : 54
Item Help
Menu Level
Drive A
Floppy 3 Mode Support
[1.44M, 3.5 in.]
[Disabled]
Video
Halt On
[EGA/VGA]
[All Errors]
Base Memory
Extended Memory
Total Memory
640K
65535K
1024K
: Move
Enter: Select +/-/PU/PD:Value
mnlkF5:Previous
Values
F6:Fail-Safe Defaults
f
Change the day, month,
year and century.
F10:Save ESC:Exit F1: General Help
F7:Optimized Defaults
Date and Time
The Date and Time items show the current date and time on the computer. If
you are running a Windows OS, these items are automatically updated whenever you make
changes to the Windows Date and Time Properties utility.
fIDE Devices (None)
Your computer has two IDE channels (Primary and Secondary) and each channel can be
installed with one or two devices (Master and Slave). In addition, this motherboard supports
two SATA channels (Primary and Secondary) and each channel allows one SATA device to
be installed. Use these items to configure each device on the IDE channel.
Press <Enter> to display the IDE submenu:
Phoenix-AwardBIOS CMOS Setup Utility
IDE Primary Master
IDE HDD Auto-Detection
IDE Channel 0 Master
Access Mode
Capacity
Cylinder
Head
Precomp
Landing Zone
Sector
[ Press Enter]
[Auto]
[Auto]
0 MB
0
0
0
0
0
Item Help
Menu Level
ff
To auto-detect the HDD’s
size, head...on this channel
mnlk: Move
Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
IDE HDD Auto-Detection
Press <Enter> while this item is highlighted to prompt the Setup Utility to automatically
detect and configure an IDE device on the IDE channel.
If you are setting up a new hard disk drive that supports LBA mode, more
than one line will appear in the parameter box. Choose the line that lists
LBA for an LBA drive.
Using BIOS
35
IDE Channel 0/1 Master/Slave (Auto)
Leave this item at Auto to enable the system to automatically detect and configure
IDE devices on the channel. If it fails to find a device, change the value to Manual and
then manually configure the drive by entering the characteristics of the drive in the
items described below.
Refer to your drive’s documentation or look on the drive casing if you need to obtain
this information. If no device is installed, change the value to None.
Before attempting to configure a hard disk drive, ensure that you have the
configuration information supplied by the manufacturer of your hard drive.
Incorrect settings can result in your system not recognizing the installed
hard disk.
Access Mode (Auto)
This item defines ways that can be used to access IDE hard disks such as LBA (Large
Block Addressing). Leave this value at Auto and the system will automatically decide
the fastest way to access the hard disk drive.
Press <Esc> to return to the Standard CMOS Features page.
Drive A (1.44M, 3.5 in./None)
These items define the characteristics of any diskette drive attached to the system.
You can connect one or two diskette drives.
Floppy 3 Mode Support (Disabled)
Floppy 3 mode refers to a 3.5-inch diskette with a capacity of 1.2 MB. Floppy 3 mode is
sometimes used in Japan.
Video (EGA/VGA)
This item defines the video mode of the system. This motherboard has a built-in VGA
graphics system; you must leave this item at the default value.
Halt On (All Errors)
This item defines the operation of the system POST (Power On Self Test) routine. You
can use this item to select which types of errors in the POST are sufficient to halt the
system.
Base Memory, Extended Memory, and Total Memory
These items are automatically detected by the system at start up time. These are
display-only fields. You cannot make changes to these fields.
Using BIOS
36
Advanced BIOS Features
This option defines advanced information about your system.
f CPU Feature
Disk Boot Priority
f Hard
CPU L3 Cache
Item Help
Menu Level
f
123
123
123
123
f
Hyper-Threading Technology
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Boot Up Floppy Seek
Boot Up NumLock Status
Gate A20 Option
Typematic Rate Setting
X Typematic Rate (Chars/Sec )
X Typematic Delay (Msec)
Security Option
APIC Mode
OS Select For DRAM > 64MB
HDD S.M.A.R.T. Capability
[Press Enter]
[Press Enter]
[Enabled]
[Enabled]
[Enabled]
[Floppy]
[Hard Disk]
[CDROM]
[Enabled]
[Disabled]
[On]
[Fast]
[Disabled]
6
250
[Setup]
[Enabled]
[Non-OS2]
[Disabled]
f
Phoenix-AwardBIOS CMOS Setup Utility
Advanced BIOS Features
mnlk : Move
Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values F6:Fail-Safe Defaults
F7:Optimized Defaults
f CPU Feature (Press Enter)
Users please note that this function is only available for Prescott CPUs. Scroll to this
item and press <Enter> to view the following screen:
Phoenix-AwardBIOS CMOS Setup Utility
CPU Feature
Delay Prior to thermal
Thermal Management
TM2 Bus Ratio
TM2 Bus VID
Limit CPUID MaxVal
NX BIOS Control
[16 Min]
[Thermal Monitor 1]
[0 X]
[0.8375V]
[Disabled]
[Disabled]
Item Help
Menu Level
ff
Thermal Monitor 1 (On die
throtting)
Thermal Monitor 2 Ratio
& VID transition
mnlk : Move
Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6”Fail-Safe Defaults
F7:Optimized
Delay Prior to Thermal (Thermal Monitor 1)
This item enables you to set the delay time before the CPU enters auto
thermal mode.
Thermal Management (Thermal Monitor 1)
This item displays CPU’s temperature and enables you to set a safe
temperature to Prescott CPU.
Using BIOS
37
TM2 Bus Ratio (0X)
This item helps you to set the frequency (bus ratio) of the throttled
performance that will be initiated when the on-die sensor goes from not
hot to hot. You may set the bus ratio number from 0-255. This feature is
available when CPU supports Thermal Monitor 2.
TM2 Bus VID (0.8375V)
This item helps you to set the voltage of the throttled performance that
will be initiated when the on-die sensor goes from not hot to hot. This
feature is available when CPU supports Thermal Monitor 2.
Limit CPUID MaxVal (Disabled)
This item can support Prescott CPUs for old OS. Users please note that under NT 4.0,
it must be set “Enabled”, while under WinXP, it must be set “Disabled”.
NX BIOS Control (Disabled)
Users please leave this item in its default setting under Windows XP OS. Change the value
to “Disabled” if users are to install Linux OS.
Press <Esc> to return to the Advanced BIOS Features screen.
f Hard Disk Boot Priority (Press Enter)
Scroll to this item and press <Enter> to view the following screen:
Phoenix-AwardBIOS CMOS Setup Utility
Hard Disk Boot Priority
1. Pri. Master:
2. Pri. Slave:
3. Sec. Master:
4. Sec. Slave:
5. USBHDD0:
6. USBHDD1:
7. USBHDD2:
8. Bootable Add-in Cards
mn
: Move
Item Help
Menu Level
m
ff
n
Use < > or < > to select
a device, then press <+> to
move it up, or <-> to move it
down the list. Press <ESC>
to exit this menu.
PU/PD/+/-/: Change Priority
F10:Save
ESC:Exit
CPU L3 Cache (Enabled)
All Prescott processors that can be installed in this mainboard use Level 3 (L3) cache
memory to improve performance. Leave this item at the default value for better performance. This item is only available when you use L3 cache supported CPU.
Hyper-Threading Technology (Enabled)
This item is only available when the chipset supports Hyper-Threading and you are
using a Hyper-Threading CPU.
Quick Power On Self Test (Enabled)
Enable this item to shorten the power on testing (POST) and have your system start
up faster. You might like to enable this item after you are confident that your system
hardware is operating smoothly.
Using BIOS
38
First/Second/Third Boot Device (Floppy/Hard Disk/CDROM)
Use these three items to select the priority and order of the devices that your system
searches for an operating system at start-up time.
Boot Other Device (Enabled)
When enabled, the system searches all other possible locations for an operating system if
it fails to find one in the devices specified under the First, Second, and Third boot devices.
Boot Up Floppy Seek (Disabled)
If this item is enabled, it checks the size of the floppy disk drives at start-up time. You
don’t need to enable this item unless you have a legacy diskette drive with 360K capacity.
Boot Up NumLock Status (On)
This item defines if the keyboard Num Lock key is active when your system is started.
Gate A20 Option (Fast)
This item defines how the system handles legacy software that was written for an earlier
generation of processors. Leave this item at the default value.
Typematic Rate Setting (Disabled)
If this item is enabled, you can use the following two items to set the typematic rate and the
typematic delay settings for your keyboard.
•
Typematic Rate (Chars/Sec): Use this item to define how many characters per second are generated by a held-down key.
•
Typematic Delay (Msec): Use this item to define how many milliseconds
must elapse before a held-down key begins generating repeat characters.
Security Option (Setup)
If you have installed password protection, this item defines if the password is required at
system start up, or if it is only required when a user tries to enter the Setup Utility.
APIC Mode (Enabled)
This item allows you to enable or disable the APIC (Advanced Programmable Interrupt
Controller) mode. APIC provides symmetric multi-processing (SMP) for systems, allowing
support for up to 60 processors.
OS Select For DRAM > 64 MB (Non-OS2)
This item is only required if you have installed more than 64 MB of memory and you are
running the OS/2 operating system. Otherwise, leave this item at the default.
HDD S.M.A.R.T Capability (Disabled)
The S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) system is a
diagnostics technology that monitors and predicts device performance. S.M.A.R.T.
software resides on both the disk drive and the host computer.
Report No FDD For WIN 95 (Yes)
This item determines whether the BIOS will report no FDD for Windows 95 OS.
Using BIOS
39
Delay for HDD (Secs) (0)
Users may set a delay from 1 to 15 seconds in the cold boot process. Some hard disk
drives need extra time to spin up in order to identify correctly. If the system does not
start after the memory test, try to add tomes in this field.
Small Logo (EPA) Show (Disabled)
Enables or disables the display of the EPA logo during boot.
Advanced Chipset Features
These items define critical timing parameters of the motherboard. You should leave the
items on this page at their default values unless you are very familiar with the technical
specifications of your system hardware. If you change the values incorrectly, you may
introduce fatal errors or recurring instability into your system.
[By SPD]
[2]
[8]
[4]
[4]
[Auto]
[Disabled]
[Disabled]
[128]
[PCI Slot]
** Photon Acceleration Technology **
Fast Chip Select
CPC Addr/Control
Turbo Mode
[Auto]
[Auto]
[Auto]
** On-Chip VGA Setting **
On-Chip VGA
On-Chip Frame Buffer Size
[Enabled]
[8MB]
Item Help
Menu Level
f
123
123
123
123
f
DRAM Timing Selectable
CAS Latency Time
Active to Precharge Delay
DRAM RAS# to CAS# Delay
DRAM RAS# Precharge
Memory Frequency For
System BIOS Cacheable
Video BIOS Cacheable
AGP Aperature Size (MB)
Init Display First
f
Phoenix-AwardBIOS CMOS Setup Utility
Advanced Chipset Features
mnlk : Move
Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
DRAM Timing Selectable (By SPD)
Enables you to select the CAS latency time in HCLKs of 2, 2.5, or 3. The value is set at the
factory depending on the DRAM installed. Do not change the values in this field unless you
change specifications of the installed DRAM or the installed CPU.
CAS Latency Time (2)
This item controls the timing delay (in clock cycles) before the DRAM starts a read
command after receiving it.
Active to Precharge Delay (8)
This precharge time is the number of cycles it takes for DRAM to accumulate its charge
before refresh.
DRAM RAS# to CAS# Delay (4)
This field lets you insert a timing delay between the CAS and RAS strobe signals, used
when DRAM is written to, read from, or refreshed. Disabled gives faster performance;
and Enabled gives more stable performance.
Using BIOS
40
DRAM RAS# Precharge (4)
Select the number of CPU clocks allocated forthe Row Address Strobe (RAS#) signal to
accumulate its charge before the DRAM is refreshed. If insufficient time is allowed,
refresh may be incomplete and data lost.
Memory Frequency For (Auto)
This item sets the main memory frequency. When you used an external graphics card,
you can adjust this to enable the best performance for your system.
System BIOS Cacheable (Disabled)
When this item is enabled, the System BIOS will be cached for faster execution.
Video BIOS Cacheable (Disabled)
When this is enabled, the Video RAM will be cached resulting to better performance.
However, if any program was written to this memory area, this may result to system error.
AGP Aperture Size (MB) (128)
This item defines the size of the aperture if you use an AGP graphics adapter. The AGP
aperture refers to a section of the PCI memory address renge used for graphics memory. We
recommend that you leave this item at the default value.
Init Display First (PCI Slot)
This item allows you to choose the primary display card.
Fast Chip Select (Auto)
This item allows you to read the Data transfer from CPU to GMCH.
CPC Addr/Control (Auto)
This item allows you to increase the performance when DDR400 DIMM is installed and set
this item to “Enabled”. However, this might cause the system to become UNSTEADY.
Turbo Mode (Auto)
This item allows you to increase the performance of CPU L2 cache timing at high speed.
On-Chip VGA (Enabled)
This item allows you to enable or disable the onboard VGA function.
On-Chip Frame Buffer Size (8MB)
This item allows you to set the onboard frame buffer size, ranging from 1MB, 8MB, to
16MB.
Boot Display (Auto)
This item allows you to set the boot display function to be “Auto”, “CRT”, “EFP”, “TV”,
“CRT+EFP”, or “CRT+TV”.
Using BIOS
41
Integrated Peripherals
These options display items that define the operation of peripheral components on the
system’s input/output ports.
Phoenix-AwardBIOS CMOS Setup Utility
Integrated Peripherals
f OnChip IDE Device
f Onboard Device
f SuperIO Device
Item Help
[Press Enter]
[Press Enter]
[Press Enter]
Menu Level
f
mnlk : Move
Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults F7:Optimized Defaults
fOnChip IDE Device
Scroll to this item and press <Enter> to view the following screen:
Phoenix-AwardBIOS CMOS Setup Utility
OnChip IDE Device
IDE HDD Block Mode
On-chip Primary PCI IDE
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
On-chip Secondary PCI IDE
IDE Secondary Master PIO
IDE Secondary Slave PIO
IDE Secondary Master UDMA
IDE Secondary Slave UDMA
ATA 66/100 Cable Msg
[Enabled]
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Enabled]
*** On-Chip Serial ATA Setting***
SATA Mode
On-chip Serial ATA
Serial ATA Port0 Mode
Serial ATA Port1 Mode
[IDE]
[Disabled]
[Primary Master]
Primary Master
Item Help
Menu Level
ff
mnlk : Move
Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults F7:Optimized Defaults
IDE HDD Block Mode (Enabled)
Block mode is also called block transfer, multiple commands, or multiple sector read/write.
If your IDE hard drive supports block mode (most new drives do), select Enabled for
automatic detection of the optimal number of block read/write per sector the drive can
support.
On-Chip Primary/Secondary PCI IDE (Enabled)
This integrated peripheral controller contains an IDE interface with support for two IDE
channels. Select Enabled to activate each channel seperately.
Using BIOS
42
IDE Primary/Secondary Master/Slave PIO (Auto)
Each IDE channel supports a master device and a slave device. These four items let you
assign the kind of PIO (Programmed Input/Output) was used by the IDE devices. Choose
Auto to let the system auto detect which PIO mode is best, or select a PIO mode from 0-4.
IDE Primary/Secondary Master/Slave UDMA (Auto)
Each IDE channel supports a master device and a slave device. This mainboard supports
UltraDMA technology, which provides faster access to IDE devices. If you install a device
that supports UltraDMA, change the appropriate item on this list to Auto. You may have
to install the UltraDMA driver supplied with this mainboard in order to use an UltraDMA
device.
ATA 66/100 Cable Msg (Enabled)
This item enalbes or disabled the display of the ATA 66/100 Cable Msg. If you install a
device that supports UDMA, change the appropriate item on this list to Auto. You may
have to install the UDMA driver supplied with this motherboard in order to use an UDMA
device.
SATA Mode (IDE)
Use this item to select the mode of the Serial ATA.
On-Chip Serial ATA (Disabled)
Enables or disables the built-in on-chip Serial ATA.
Serial ATA Port0/Port1 Mode (Primary Master)
Use this item to select the SATA0 master or SATA1 master.
Press <Esc> to return to the Integrated Peripherals screen.
fOnboard Device
Scroll to this item and press <Enter> to view the following screen:
Phoenix-AwardBIOS CMOS Setup Utility
Onboard Device
USB Controller
USB 2.0 Controller
USB Keyboard Support
USB Mouse Support
AC97 AUDIO
Onboard LAN Device
Onboard LAN Boot ROM
Onboard 1394 Device
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Auto]
[Enabled]
[Disabled]
[Enabled]
Item Help
Menu Level
ff
mnlk : Move
Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
USB Controller (Enabled)
This item enables the USB controller. Leave this at the default “Enabled” if you want to
connect USB devices to your computer.
USB 2.0 Controller (Enabled)
Enable this item if want to use the USB 2.0.
Using BIOS
43
USB Keyboard Support (Enabled)
This item allows the BIOS to interact with a USB keyboard or mouse to work with MS-DOS
based utilities and non-Windows modes.
USB Mouse Support (Enabled)
Enable this item if you plan to use a mouse connected through the USB port in a legacy
operating system (such as DOS) that does not support Plug and Play.
AC97 AUDIO (Enabled)
This option allows you to control the onboard AC97 audio. Disable this item if you are
going to install a PCI audio add-on card.
Onboard LAN Device (Enabled)
This option allows you to enable or disable the onboard LAN function.
Onboard LAN Boot ROM (Disabled)
Use this item to enable and disable the booting from the onboard LAN or a network add-in
card with a remote boot ROM installed.
Onboard 1394 Device (Enabled)
This option allows you to enable or disable the onboard 1394 function.
Press <Esc> to return to the Integrated Peripherals screen.
fSuperIO Device
Scroll to this item and press <Enter> to view the following screen:
Phoenix-AwardBIOS CMOS Setup Utility
SuperIO Device
POWER ON Function
KB Power ON Password
Hot key Power ON
Onboard FDC Controller
Onboard Serial Port1
UART 2 Mode Control
UART Mode Select
RxD , TxD Active
IR Transmission Delay
UR2 Duplex Mode
Use IR Pins
Onboard Parallel Port
Parallel Port Mode
ECP Mode Use DMA
Power On After Power Fail
[Hot Key]
[Enter]
[Ctrl-F12]
[Enabled]
[3F8/IRQ4]
[Disabled]
[Normal]
[Hi, Lo]
[Enabled]
[Half]
[IR-Rx2Tx2]
[378/IRQ7]
[ECP]
[3]
[Off]
Item Help
Menu Level
ff
mnlk : Move
Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
POWER ON Function (Hot Key)
This feature allows you to set the method by which your system can be turned on.
KB Power ON Password (Enter)
When the POWER ON Function is set to Password, use this item to set the passowrd.
Using BIOS
44
Hot Key Power On (Ctrl-F12)
When the POWER ON Function is set to Hot Key, use this item to set the hot key
combination that turns on the system.
Onboard FDC Controller (Enabled)
Select Enabled if your system has a floppy disk controller (FDC) installed on the system
board and you wish to use it. If you install an add-in FDC or the system has no floppy drive,
select Disabled in this field.
Onboard Serial Port1 (3F8/IRQ4)
This option is used to assign the I/O address and interrupt request (IRQ) for onboard serial
port1 (COM1).
UART 2 Mode Control (Disabled)
This item allows users to enable or disable the onboard UART2 mode control.
UART Mode Select (2F8/IRQ3)
This field is available if the “Onboard Serial Port 2” is set to any option but Disabled. UART
Mode Select enables you to select the infrared communication protocol-Normal (default),
IrDA, or ASKIR. IrDA is an infrared communication protocol with a maximum baud rate up
to 115.2K bps. ASKIR is Sharp’s infrared communication protocol with a maximum baud
rate up to 57.6K bps.
RxD , TxD Active (Hi, Lo)
This feature enables you to set the IR reception/transmission polarity as High or Low
IR Transmission Delay (Enabled)
This field enables you to set the whether the IR transmission rate will be delayed while
converting to receiving mode.
UR2 Duplex Mode (Half)
This field is available when UART 2 Mode is set to either ASKIR or IrDA. This item enables
you to determine the infrared function of the onboard infrared chip. The options are Full
and Half (default). Full-duplex means you can transmit and receive data simultaneously.
Half-duplex is the transmission of data in either transmitting or receiving, only one direction at a time.
Use IR Pins (IR-Rx2Tx2)
Please consult your IR peripheral documentation to select the correct setting of the
TxD and RxD signals.
Onboard Parallel Port (378/IRQ7)
This option is used to assign the I/O address and interrupt request (IRQ) for the onboard
parallel port.
Parallel Port Mode (ECP)
Enables you to set the data transfer protocol for your parallel port. There are four options:
SPP (Standard Parallel Port), EPP (Enhanced Parallel Port), ECP (Extended Capabilities
Port), and ECP+EPP.
SPP allows data output only. Extended Capabilities Port (ECP) and Enhanced Parallel Port
(EPP) are bi-directional modes, allowing both data input and output. ECP and EPP modes
are only supported with EPP- and ECP-aware peripherals.
Using BIOS
45
ECP Mode Use DMA (3)
When the onboard parallel port is set tp ECP mode, the parallel port can use DMA3 or
DMA1.
Power On After Power Fail (Off)
This item enables your computer to automatically restart or return to its last operating
status after power returns from a power failure.
Press <Esc> to return to the Integrated Peripherals screen.
Using BIOS
46
Power Management Setup
This option lets you control system power management. The system has various powersaving modes including powering down the hard disk, turning off the video, suspending to
RAM, and software power down that allows the system to be automatically resumed by
certain events.
The power-saving modes can be controlled by timeouts. If the system is inactive for a time,
the timeouts begin counting. If the inactivity continues so that the timeout period elapses,
the system enters a power-saving mode. If any item in the list of Reload Global Timer
Events is Enabled, then any activity on that item will reset the timeout counters to zero.
If the system is suspended or has been powered down by software, it can be resumed by a
wake up call that is generated by incoming traffic to a modem, a LAN card, a PCI card,
or a fixed alarm on the system realtime clock
Phoenix-AwardBIOS CMOS Setup Utility
Power Management Setup
x
x
ACPI Suspend Type
Run VGABIOS if S3 Resume
Video Off Method
Video Off In Suspend
Suspend Type
Modem Use IRQ
Suspend Mode
HDD Power Down
Soft-Off by PWR-BTTN
Resume by PCI PME
Resume by Ring
Resume by USB (S3)
Resume by Alarm
Date (of Month) Alarm
Time (hh:mm:ss) Alarm
[S3 (STR)]
[Auto]
[DPMS]
[Yes]
[Stop Grant]
[3]
[Disabled]
[Disabled]
[Instant-Off]
[Enabled]
[Disabled]
[Disabled]
[Disabled]
0
0 0 0
** Reload Global Timer Evernts **
Primary IDE 0
Primary IDE 1
[Disabled]
[Disabled]
Item Help
Menu Level
f
12
12
12
12
Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
mnlk : Move
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
ACPI Suspend Type (S3(STR))
Use this item to define how your system suspends. In the default, S1 (POS), the suspend
mode is equivalent to a software power down. If you select S3 (STR), the suspend mode is
suspend to RAM, i.e., the system shuts down with the exception of a refresh current to the
system memory.
Run VGABIOS if S3 Resume (Auto)
Use this item to initialize the VGA BIOS from S3 (Suspend to RAM) sleep state.
Video Off Method (DPMS)
This item defines how the video is powered down to save power. This item is set to DPMS
(Display Power Management Software) by default.
Video Off In Suspend (Yes)
This option defines if the video is powered down when the system is put into suspend mode.
Using BIOS
47
Suspend Type (Stop Grant)
If this item is set to the default Stop Grant, the CPU will go into Idle Mode during power
saving mode.
MODEM Use IRQ (3)
If you want an incoming call on a modem to automatically resume the system from a
power-saving mode, use this item to specify the interrupt request line (IRQ) that is used by
the modem. You might have to connect the fax/modem to the motherboard Wake On
Modem connector for this feature to work.
Suspend Mode (Disabled)
The CPU clock will be stopped and the video signal will be suspended if no Power Management events occur for a specified length of time. Full power function will return when a
Power Management event is detected. Options are from 1 Min to 1 Hour and Disabled.
HDD Power Down (Disabled)
The IDE hard drive will spin down if it is not accessed within a specified length of time.
Options are from 1 Min to 15 Min and Disable.
Soft-Off by PWR-BTTN (Instant-Off)
Under ACPI (Advanced Configuration and Power management Interface) you can create a
software power down. In a software power down, the system can be resumed by Wake Up
Alarms. This item lets you install a software power down that is controlled by the power
button on your system. If the item is set to Instant-Off, then the power button causes a
software power down. If the item is set to Delay 4 Sec. then you have to hold the power
button down for four seconds to cause a software power down.
Resume by PCI PME (Enabled)
This item specifies whether the system will be awakened from power saving modes when
activity or input signal of the specified hardware peripheral or component is detected.
Resume by Ring (Disabled)
An input signal on the serial Ring indicator (RI) line (in other words, and incoming call on
the modem) awakens the system from a soft off state.
Resume by USB (S3) (Disabled)
This option allows the activity of the USB devices (keyboard and mouse) to wake-up the
system from S3 sleep state.
Resume by Alarm (Disabled)
When set to Enabled, additional fields become available and you can set the date (day of the
month), hour, minute and second to turn on your system. When set to 0 (zero) for the day
of the month, the alarm will power on your system every day at the specified time.
** Reload Global Timer Events **
This field indicates which events waken the system from power saving mode.
Primary/Secondary IDE 0/1 (Disabled)
When this item is enabled, the system power will resume the system from a power saving
mode if there is any activity on primary or secondary IDE channel 0 or 1.
Using BIOS
48
FDD, COM, LPT Port (Disabled)
When this item is enabled, the system power will resume the system from a power saving
mode if there is any activity on FDD, COM, or LPT port.
PCI PIRQ [A-D] # (Disabled)
When this item is enabled, the system power will resume the system from a power saving
mode if there is any activity on PCI or PIRQ devices.
PNP/PCI Configurations
This section describes configuring the PCI bus system. PCI (Peripheral Component Interconnect) is a system, which allows I/O devices to operate at speeds nearing CPU’s when they
communicate with own special components. All the options describes in this section are
important and technical and it is strongly recommended that only experienced users should
make any changes to the default settings.
Phoenix-AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
Reset Configuration Data
[Disabled]
Resources Controlled By
x IRQ Resources
[Auto(ESCD)]
Press Enter
PCI/VGA Palette Snoop
Assign IRQ For USB
INT Pin 1 Assignment
INT Pin 2 Assignment
INT Pin 3 Assignment
INT Pin 4 Assignment
INT Pin 5 Assignment
INT Pin 6 Assignment
INT Pin 7 Assignment
INT Pin 8 Assignment
[Disabled]
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
mnlk : Move
Enter: Select +/-/PU/PD:Value
F5:Previous Values
F6:Fail-Safe Defaults
Item Help
Menu Level
ff
Default is Disabled. Select
Enabled to reset Extended
System Configuration Data
(ESCD) when you exit Setup
if you have installed a new
add-on and the system
reconfiguration has caused
such a serious conflict that
the OS cannot boot
F10:Save ESC:Exit F1: General Help
F7:Optimized Defaults
Reset Configuration Data (Disabled)
When you enable this item and restart the system, any Plug and Play configuration data
stored in the BIOS Setup is cleared from memory.
Resources Controlled By (Auto(ECSD))
You should leave this item at the default Auto(ESCD). Under this setting, the system
dynamically allocates resources to Plug and Play devices as they are required. If you cannot
get a legacy ISA (Industry Standard Architecture) expansion card to work properly, you
might be able to solve the problem by changing this item to Manual, and then opening up
the IRQ Resources submenu.
•
In the IRQ Resources submenu, if you assign an IRQ to Legacy ISA, then that
Interrupt Request Line is reserved for a legacy ISA expansion card. Press
<Esc> to close the IRQ Resources submenu.
Using BIOS
49
PCI/VGA Palette Snoop (Disabled)
This item is designed to overcome problems that can be caused by some non-standard VGA
cards. This board includes a built-in VGA system that does not require palette snooping so
you must leave this item disabled.
Assign IRQ For USB (Enabled)
“Enable” or “Disable” this item when users are to assign IRQ for the USB interface onboard.
INT Pin1~8 Assignment (Auto)
Identifies the interrupt request (IRQ) line assigned to a device connected to the PCI interface of your system.
PC Health Status
On motherboards that support hardware monitoring, this item lets you monitor the parameters for critical voltages, critical temperatures, and fan speeds.
Phoenix-AwardBIOS CMOS Setup Utility
PC Health Status
Target Temperature
Shutdown Temperature
Vcore (V)
3.30 V
5.00 V
12.00 V
1.50 V
5VSB (V)
VBT (V)
Current System Temperature
Current CPU Temperature
Current System FAN Speed
Current CPU FAN Speed
Current Power FAN Speed
[Disabled]
[Disabled]
Item Help
Menu Level
f
mnlk: Move
Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1: General Help
F5:Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Target Temperature (Disabled)
This item enables throttling when CPU targets the temperature.
Shutdown Temperature (Disabled)
Enables you to set the maximum temperature the system can reach before powering down.
System Component Characteristics
These items allow end users and technicians to monitor data provided by the BIOS on this
motherboard. You cannot make changes to these fields.
•
Current CPU/System Temperature
•
CPU Fan Speed
•
CPU Core Voltage
•
Battery Voltage
Using BIOS
50
Frequency Control
This item enables you to set the clock speed and system bus for your system. The clock
speed and system bus are determined by the kind of processor you have installed in your
system.
Phoenix-AwardBIOS CMOS Setup Utility
Frequency Control
CPU Clock Ratio
Auto Detect PCI Clk
Spread Spectrum
Async AGP/PCI CLK
CPU Clock
[8X]
[Enabled]
[Enabled]
[Disabled]
[100MHz]
mnlk : Move
Enter: Select +/-/PU/PD:Value
F5:Previous Values
F6:Fail-Safe Defaults
Item Help
Menu Level
f
F10:Save ESC:Exit F1: General Help
F7:Optimized Defaults
CPU Clock Ratio (8X)
Enables you to set the CPU clock. The CPU clock ratio times the CPU Host/PCI Clock
should equal the core speed of the installed processor. (For unlock Ratio CPU only.)
Example:
CPU Clock Ratio
CPU Frequency
Installed CPU Clock Speed
8
X100
800 MHz
Auto Detect DIMM/PCI Clk (Enabled)
When this item is enabled, BIOS will disable the clock signal of free DIMM and PCI slots.
Spread Spectrum (Enabled)
If you enable spread spectrum, it can significantly reduce the EMI (Electro-Magnetic
Interference) generated by the system.
Async AGP/PCI CLK (Disabled)
This item allows you to select the fixed clock to generate the output to AGP/PCI frequency.
CPU Clock (100MHz)
Use the CPU Host Clock to set the frontside bus frequency for the installed processor
(usually 133 MHz, 100 MHz, or 66 MHz).
Using BIOS
51
Load Fail-Safe Defaults Option
This option opens a dialog box that lets you install fail-safe defaults for all appropriate
items in the Setup Utility:
Press <Y> and then <Enter> to install the defaults. Press <N> and then <Enter> to not
install the defaults. The fail-safe defaults place no great demands on the system and are
generally stable. If your system is not functioning correctly, try installing the fail-safe
defaults as a first step in getting your system working properly again. If you only want to
install fail-safe defaults for a specific option, select and display that option, and then press
<F6>.
Load Optimized Defaults Option
This option opens a dialog box that lets you install optimized defaults for all appropriate
items in the Setup Utility. Press <Y> and then <Enter> to install the defaults. Press <N> and
then <Enter> to not install the defaults. The optimized defaults place demands on the
system that may be greater than the performance level of the components, such as the CPU
and the memory. You can cause fatal errors or instability if you install the optimized defaults
when your hardware does not support them. If you only want to install setup defaults for a
specific option, select and display that option, and then press <F7>.
Set Supervisor/User Password
When this function is selected, the following message appears at the center of the screen to
assist you in creating a password.
ENTER PASSWORD
Type the password, up to eight characters, and press <Enter>. The password typed now
will clear any previously entered password from CMOS memory. You will be asked to
confirm the password. Type the password again and press <Enter>. You may also press
<Esc> to abort the selection.
To disable password, just press <Enter> when you are prompted to enter
password. A message will confirm the password being disabled. Once the password is
disabled, the system will boot and you can enter BIOS Setup freely.
PASSWORD DISABLED
If you have selected “System” in “Security Option” of “BIOS Features Setup” menu, you
will be prompted for the password every time the system reboots or any time you try to
enter BIOS Setup.
If you have selected “Setup” at “Security Option” from “BIOS Features Setup” menu, you
will be prompted for the password only when you enter BIOS Setup.
Supervisor Password has higher priority than User Password. You can use Supervisor Password when booting the system or entering BIOS Setup to modify all settings. Also you can
use User Password when booting the system or entering BIOS Setup but can not modify any
setting if Supervisor Password is enabled.
Save & Exit Setup Option
Highlight this item and press <Enter> to save the changes that you have made in the Setup
Utility and exit the Setup Utility. When the Save and Exit dialog box appears, press <Y> to
save and exit, or press <N> to return to the main menu:
Using BIOS
52
Exit Without Saving
Highlight this item and press <Enter> to discard any changes that you have made in the
Setup Utility and exit the Setup Utility. When the Exit Without Saving dialog box appears,
press <Y> to discard changes and exit, or press <N> to return to the main menu.
If you have made settings that you do not want to save, use the “Exit Without
Saving” item and press <Y> to discard any changes you have made.
This concludes Chapter 3. Refer to the next chapter for information on the software
supplied with the motherboard.
Using BIOS
53
Chapter 4
Using the Motherboard Software
About the Software CD-ROM
The support software CD-ROM that is included in the motherboard package contains all the
drivers and utility programs needed to properly run the bundled products. Below you can find
a brief description of each software program, and the location for your motherboard
version. More information on some programs is available in a README file, located in the
same directory as the software.
Never try to install all software from folfer that is not specified for use with your
motherboard.
Before installing any software, always inspect the folder for files named README.TXT,
INSTALL.TXT, or something similar. These files may contain important information that
is not included in this manual.
Auto-installing under Windows 98/ME/2000/XP
The Auto-install CD-ROM makes it easy for you to install the drivers and software for your
motherboard.
If the Auto-install CD-ROM does not work on your system, you can still install
drivers through the file manager for your OS (for example, Windows Explorer). Refer to the Utility Folder Installation Notes later in this chapter.
The support software CD-ROM disc loads automatically under Windows 98/ME/2000/XP.
When you insert the CD-ROM disc in the CD-ROM drive, the autorun feature will automatically bring up the install screen. The screen has three buttons on it, Setup, Browse CD and
Exit.
If the opening screen does not appear; double-click the file “setup.exe” in
the root directory.
Using the Motherboard Software
54
Setup Tab
Setup
Click the Setup button to run the software installation program. Select
from the menu which software you want to install.
Browse CD The Browse CD button is the standard Windows command that allows
you to open Windows Explorer and show the contents of the support
CD.
Before installing the software from Windows Explorer, look for a file
named README.TXT, INSTALL.TXT or something similar. This file
may contain important information to help you install the software
correctly.
Some software is installed in separate folders for different operating
systems, such as DOS, WIN NT, or WIN98/95. Always go to the correct
folder for the kind of OS you are using.
In install the software, execute a file named SETUP.EXE or INSTALL.EXE
by double-clicking the file and then following the instructions on the
screen.
Exit
The EXIT button closes the Auto Setup window.
Application Tab
Lists the software utilities that are available on the CD.
Read Me Tab
Displays the path for all software and drivers available on the CD.
Running Setup
Follow these instructions to install device drivers and software for the motherboard:
1.
Click Setup. The installation program begins:
The following screens are examples only. The screens and driver lists will be
different according to the motherboard you are installing.
The motherboard identification is located in the upper left-hand corner.
Using the Motherboard Software
55
2.
Click Next. The following screen appears:
3.
Check the box next to the items you want to install. The default options are recommended.
4.
Click Next run the Installation Wizard. An item installation screen appears:
5.
Follow the instructions on the screen to install the items.
Drivers and software are automatically installed in sequence. Follow the onscreen instructions, confirm commands and allow the computer to restart a few times to complete the
installation.
Using the Motherboard Software
56
Manual Installation
Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root directory.
This file contains the information needed to locate the drivers for your motherboard.
Look for the chipset and motherboard model; then browse to the directory and path to
begin installing the drivers. Most drivers have a setup program (SETUP.EXE) that automatically detects your operating system before installation. Other drivers have the setup
program located in the operating system subfolder.
If the driver you want to install does not have a setup program, browse to the operating
system subfolder and locate the readme text file (README.TXT or README.DOC) for
information on installing the driver or software for your operating system.
Utility Software Reference
All the utility software available from this page is Windows compliant. They are provided
only for the convenience of the customer. The following software is furnished under license
and may only be used or copied in accordance with the terms of the license.
These software(s) are subject to change at anytime without prior notice.
Please refer to the support CD for available software.
AWARD Flash Memory Utility
This utility lets you erase the system BIOS stored on a Flash Memory chip on the motherboard,
and lets you copy an updated version of the BIOS to the chip. Proceed with caution when
using this program. If you erase the current BIOS and fail to write a new BIOS, or write a
new BIOS that is incorrect, your system will malfunction. Refer to Chapter 3, Using BIOS for
more information.
WinFlash Utility
The Award WinFlash utility is a Windows version of the DOS Award BIOS flash writer utility.
The utility enables you to flash the system BIOS stored on a Flash Memory chip on the
motherboard while in a Windows environment. This utility is currently available for
WINXP\ME\2000\98SE. To install the WinFlash utility, run WINFLASH.EXE from the
following directory: \UTILITY\WINFLASH 1.51
PC-CILLIN
The PC-CILLIN software program provides anti-virus protection for your system. This
program is available for Windows 2000/ME/98SE/XP and Windows NT. Be sure to check
the readme.txt and install the appropriate anti-virus software for your operating system.
We strongly recommend users to install this free anti-virus software to help protect your
system against viruses.
This concludes Chapter 4.
Using the Motherboard Software
Cette carte mère utilise un type LGA775 de Pentium 4 présentant les fonctionnalités
suivantes :
•
Peut recevoir les derniers processeurs Intel P4/Celeron
•
Prend en charge un bus système (FSB) de 800/533 MHz
•
Prend en charge le CPU de technologie " Hyper-Threading"
La technologie “Hyper-Threading” permet au système d’exploitation de penser qu’il est
connecté à deux processeurs, permettant d’exécuter deux threads en parallèle, à la fois sur des
processeurs «logiques» séparés dans le même processeur physique.
Chipset
Les chipsets Intel 865GV(GMCH) Northbridge (NB) et 82801EB(ICH5) Southbridge
(SB) sont basés sur une architecture novatrice et dimensionnable avec une fiabilité et des
performances prouvées.
865GV (NB)
•
•
•
•
•
ICH5 (SB)
•
•
•
•
•
Prend en charge les processeurs P4/Celeron avec vitesse
de transfert allant jusqu’à 800/533/400MHz
Prend en charge la DDR-SDRAM à 400/333/266MHz
AGTL+bus d’hôte avec terminaison intégrée prenant en
charge l’adressage d’hôte de 32 bits
Interface hub 8 bits/66MHz 8X sur Intel ICH5
Comprend un accélérateur graphique intégré offrant des
capacités 3D, 2D et vidéo d’un bon rapport qualité-prix.
Prend en charge jusqu’à six Maîtres PCI entièrement conformes aux spécifications PCI 2.3 à 33MHz
Prend en charge 2 Contrôleurs IDE de Maître Bus à canaux
Ultra ATA 100
Prend en charge deux contrôleurs d’hôte ATA Série
Conforme à AC’97 v2.3 prenant en charge 6 canaux de
sorties audio
Prend en charge huit ports USB 2.0 pour transfets en série
à 480Mb/s maximum
Mémoire
Ce contrôleur de mémoire peut recevoir jusqu’à quatre SDRAM DDR DIMM 2.5V,
prenant en charge les DDR400/333/266MHz avec une taille mémoire maximum d’une
capacité de 4Go.
CODEC Audio
•
•
•
•
•
CODEC full-duplex 16 bits avec vitesse d’échantillonnage de 48KHz
Conforme aux spécifications AC’97 v2.3
Prend en charge la vitesse d’échantillonnage double (96KHz) de la lecture
audio DVD
Prend en charge la fonction d’entrée et sortie S/PDIF
Compatible Direct Sound 3DTM
Multi-Language Translation
Français
Caractéristiques
Processeur
Français
Graphique
•
•
•
•
•
•
Configuration 3D et moteur de rendu
Amélioration graphique 2D/3D
DVD/PV-VCR Vidéo
Moteur de texture de haute qualité
Prise en charge du rendu de zone
Superposition vidéo
Options d’extension
La carte mère est livrée avec les options d’extensions suivantes:
•
Trois logements PCI 32 bits
•
Un logement AGP Express
•
Deux connecteurs SATA à 7 broches
•
Deux connecteurs IDE prenant en charge quatre périphériques IDE
•
Une interface de lecteur de disquette
•
Un logement CNR optionnel
Cette carte mère prend en charge la maîtrise de bus Ultra DMA avec des vitesses de transfert de
100/66/33 Mo/s.
LAN interne (optionnel)
Le LAN interne offre les caractéristiques suivantes:
•
Supporte le fonctionnement en Auto-négociation N-Way en 10Mb/s et 100Mb/
s
•
Half et Full Duplex
•
Prend en charge la fonction Wake-On-LAN (WOL) (réveil par appel réseau)
et le réveil à distance
•
Prend en charge le Contrôle de Flux Full Duplex (IEEE 802.3x)
E/S intégrées
La carte mère possède un jeu complet de ports d’E/S et de connecteurs:
•
Deux ports PS/2 pour souris et clavier
•
Un port série
•
Un port parallèle
•
Quatre ports USB
•
Un port VGA
•
Un port LAN (optionnel)
•
Un port 1394 (optionnel)
•
Prises audio pour microphone, ligne d’entrée et ligne de sortie
Microprogramme BIOS
Cette carte mère utilise Award BIOS qui permet aux utilisateurs de configurer de nombreuses
caractéristiques du système comprenant les suivantes :
•
Gestion de l’alimentation
•
Paramètres de CPU
•
Synchronisation du CPU et de la mémoire
Le microprogramme peut aussi être utilisé pour définir les paramètres pour les vitesses d’horloges
de différents processeurs.
Certaines spécifications matérielles et éléments de logiciels peuvent être modifiés
sans avertissement.
Multi-Language Translation
Feature
Das Motherboard verwendet einen LGA775 Typ Pentium 4 mit den folgenden Eigenschaften:
•
Nimmt die neuesten P4/Celeron Prozessoren auf
•
Unterstützt einen Systembus (FSB) mit 800/533MHz
•
Unterstützt eine CPU mit „Hyper-Threading“ Technologie
Bei der „Hyper-Threading” Technologie „denkt” das Betriebssystem, dass es an zwei
Prozessoren angeschlossen ist. Dadurch können im selben physikalischen Prozessor zwei
Threads parallel auf separaten „logischen“ Prozessoren laufen.
Chipsatz
Intel 865GV(GMCH) Northbridge (NB) und) 82801EB(ICH5) Southbridge (SB) Chipsätze
basieren auf einer innovativen und skalierbaren Architektur mit bewiesener Zuverlässigkeit
und Leistung.
865GV (NB)
•
•
•
•
•
ICH5 (SB)
•
•
•
•
•
Unterstützt P4/Celeron Prozessoren mit Datentransferraten
bis zu 800/533/400MHz
Unterstützt DDR SDRAM bei 400/333/266MHz
AGTL+Host Bus mit Integrated Termination unterstützt 32Bit Host Addressing
8-Bit/66MHz 8X Hub Interface zum Intel ICH5
Bietet einen integrierten Grafikbeschleuniger mit
kostengünstiger 3D-, 2D- und Videofähigkeit.
Unterstützt bis zu sechs PCI Masters; vollständige
Entsprechung zu PCI 2.3 Spezifikation bei 33MHz
Unterstützt 2-Kanal Ultra ATA 100 Bus Master IDEController
Unterstützt zwei Serial ATA Host-Controller
Entspricht AC’97 v2.3 und unterstützt 6-KanalAudioausgaben
Unterstützt acht USB 2.0 Ports für serielle Übertragungen
mit bis zu 480Mb/s
Speicher
Der Speicher-Controller kann bis zu vier 2.5V DIMM DDR SDRAM aufnehmen und
unterstützt DDR400/333/266MHz mit einer maximalen Speicherkapazität von 4GB.
Audio CODEC
•
•
•
•
•
16-Bit Stereo-Vollduplex CODEC mit einer Samplingrate von 48KHz
Entspricht AC’97 v2.3 Spezifikation
Unterstützt bei der DVD-Audiowiedergabe die doppelte Samplingrate
(96KHz)
Unterstützt S/PDIF-Eingabe- und Ausgabe-Funktion
Kompatibel mit Direct Sound 3DTM
Multi-Language Translation
Deutsche
Prozessor
Grafik
Deutsche
•
•
•
•
•
•
3D-Setup und Render Engine
2D/3D-Grafikerweiterung
Video DVD/PV-VCR
Qualitativ hochwertiger Texture Engine
Unterstützt Zone Rendering
Video-Overlay
Erweiterungsoptionen
Das Motherboard bietet die folgenden Erweiterungsoptionen:
•
Drei 32-Bit PCI-Steckplätze
•
Ein AGP-Express-Steckplatz
•
Zwei 7-Pin SATA-Stecker
•
Zwei IDE-Stecker, die vier IDE-Geräte unterstützen
•
Ein Steckplatz für ein Diskettenlaufwerk
•
Ein optionaler CNR-Steckplatz
Dieses Motherboard unterstützt Ultra DMA Bus-Mastering mit Transferraten von 100/66/33MB/
s.
Integriertes LAN (optional)
Das integrierte LAN bietet folgende Features:
•
Unterstützt den Betrieb bei 10Mb/s und 100Mb/s N-Way Auto-Negotiation
•
Halb- und Vollduplex
•
Unterstützt Wake-On-LAN-Funktion und Remote-Wake-up
•
Unterstützt Vollduplex-Flusskontrolle (IEEE 802.3x)
Integrierte I/O-Schnittstellen
Das Motherboard verfügt über einen kompletten Satz von I/O-Schnittstellen und Anschlüssen:
•
Zwei PS/2-Schnittstellen für Tastatur und Maus
•
Eine serielle Schnittstelle
•
Eine parallele Schnittstelle
•
Vier USB- Schnittstellen
•
Eine VGA- Schnittstelle
•
Eine LAN-Schnittstelle (optional)
•
Eine 1394-Steckplatz (optional)
•
Audiobuchsen für Mikrofon, Line-In und Line-Out
BIOS Firmware
Dieses Motherboard setzt das Award BIOS ein, mit dem der Anwender viele Systemeigenschaften
selbst konfigurieren kann, einschließlich der folgenden:
•
Energieverwaltung
•
CPU-Parameter
•
CPU- und Speichertiming
Mit der Firmware können auch Parameter für verschiedene Prozessortaktgeschwindigkeiten
eingestellt werden.
Einige Hardware- und Software-Spezifikationen können jederzeit und ohne
vorherige Ankündigung geändert werden.
Multi-Language Translation
La scheda madre utilizza un tipo LGA775 di Pentium 4 che offre le seguenti caratteristiche:
•
Compatibilità con i più recenti processori Intel P4/Celeron
•
Supporto di un bus di sistema (FSB) da 800/533 MHz
•
Supporto di CPU con tecnologia “Hyper-Threading”
La tecnologia “Hyper-Threading” simula per il sistema operativo una sorta di doppio
processore e consente a due processi di essere eseguiti in parallelo, ciascuno su un diverso
processore “logico” all’interno del medesimo processore fisico.
Chipset
I chipset 865GV (GMCH) Northbridge (NB) e 82801EB (ICH5) Southbridge (SB) di
Intel sono basati su un’innovativa architettura scalabile e offrono collaudata affidabilità e
prestazioni comprovate.
865GV (NB)
•
•
•
•
•
ICH5 (SB)
•
•
•
•
•
Supporto di processori P4/Celeron con velocità di trasferimento dati fino a 800/533/400 MHz
Supporto di DDR SDRAM a 400/333/266 MHz
AGTL+Host Bus con terminazione integrata compatibile
con indirizzamento host a 32 bit
Interfaccia hub 8X a 8 bit/66 MHz per Intel ICH5
Acceleratore grafico integrato con funzionalità 3D, 2D e
video a un costo concorrenziale.
Supporto di fino a sei master PCI conformi alla specifica
PCI 2.3 a 33 MHz
Supporto di controller IDE Bus Master Ultra ATA 100 a 2
canali
Supporto di due controller host ATA seriali
Conforme alla specifica AC’97 v2.3 con supporto di 6
canali audio in uscita
Supporto di otto porte USB 2.0 per trasferimenti seriali a
480 Mbit/s
Memoria
Il controller di memoria è supporta fino a quattro SDRAM DDR DIMM a 2,5 V e fino a
4 GB di memoria con DDR a 400/333/266 MHz.
CODEC Audio
•
•
•
•
•
CODEC full-duplex stereo a 16 bit con velocità di campionamento di 48
KHz
Conforme alla specifica AC’97 v2.3
Supporto di velocità di campionamento doppia (96 KHz) per la riproduzione
audio di DVD
Supporto di funzionalità S/PDIF in ingresso e in uscita
Compatibile con Direct Sound 3DTM
Multi-Language Translation
Italiano
Caratteristiche
Processore
Grafica
Italiano
•
•
•
•
•
•
Setup 3D e motore di rendering
Funzionalità avanzate di grafica 2D/3D
Video DVD/PV-VCR
Motore di trama ad alta qualità
Supporto di rendering delle aree
Supporto di Video Overlay
Opzioni di espansione
La scheda madre è dotata delle seguenti opzioni di espansione:
•
Tre slot PCI a 32 bit
•
Uno slot AGP Express
•
Due connettori SATA a 7 pin
•
Due connettori IDE per il supporto di 4 componenti IDE
•
Un’interfaccia per unità disco floppy
•
Uno slot CNR opzionale
La scheda madre supporta la funzionalità di bus mastering Ultra DMA con velocità di
trasferimento di 100/66/33 MB/s.
LAN integrata (opzionale)
La funzionalità LAN integrata sulla scheda offre le seguenti caratteristiche:
•
Supporto di NWay Auto-negotiation a 10 Mb/s e 100 Mb/s
•
Half/Full Duplex
•
Supporto di funzionalità Wake-On-LAN e riattivazione remota del sistema
•
Supporto di controllo flusso full duplex (IEEE 802.3x)
I/O integrati
La scheda madre offre una serie completa di porte e connettori I/O:
•
Due porte PS/2 per mouse e tastiera
•
Una porta seriale
•
Una porta parallela
•
Quattro porte USB
•
Una porta VGA
•
Una porta LAN (opzionale)
•
Una porta 1394 (opzionale)
•
Prese jack audio per microfono, line-in e line-out
Firmware BIOS
Questa scheda madre si avvale del BIOS Award che consente la configurazione personalizzata di
molte funzionalità del sistema, tra cui:
•
Gestione dell’alimentazione
•
Parametri CPU
•
Sincronizzazione di CPU e memoria
Il firmware consente inoltre di impostare i parametri per diverse velocità di clock del
processore.
Alcune specifiche hardware e voci di software possono essere modificate senza
preavviso.
Multi-Language Translation
Característica
Procesador
La tecnología “Hyper-Threading” habilita el sistema operativo en pensar que está conectado
a dos procesadores, que permite dos hilos a correr en paralelo, ambos en procesadores
"lógicos" separados dentro de un mismo procesador físico.
Chipset
Los chipsets 865GV(GMCH) Northbridge (NB) y 82801EB(ICH5) Southbridge (SB) de
Intel se basan de una arquitectura innovadora y escalable con la fiablidad y rendimiento
comprobados.
865GV (NB)
•
•
•
•
•
ICH5 (SB)
•
•
•
•
•
Soporta procesadores P4/Celeron con índice de transferencia de datos hasta 800/533/400MHz
Soporta DDR SDRAM en 400/333/266MHz
AGTL+Bus Anfitrión con Terminación Integrada que
soporta Dirección Anfitriona de 32-Bits
Interfaz de Hub 8X de 8-bits/66MHz al Intel ICH5
Provee un acelerador de gráficas integrado que entrega
capacidades de vídeo, 3D, 2D eficientes de costo.
Soporta hasta seis PCI Masters con conformidad total de la
especificación PCI 2.3 en 33MHz
Soporta controladores IDE másters de bus Ultra ATA 100
de 2 canales.
Soporta dos controladores Anfitriones ATA Serial
Conforme con AC’97 v2.3 que soporta 6 canales de
salidas de audio
Soporta ocho puertos USB 2.0 para las transferencias
seriales en máximo de 480Mb/s
Memoria
Este controlador de memoria puede acomodar hasta cuatro 2.5V DIMM DDR SDRAM,
que soporta DDR400/333/266MHz con el tamaño de memoria máximo de 4GB.
CODEC de audio
•
•
•
•
•
CODEC de full dulplex de estéreo 16-bit con índice de muestreo de
48KHz
Conformidad con la especificación AC’97 v2.3
Soporta índice de muestreo doble (96KHz) de la reproducción de audio
DVD
Soporta la función de entrada y salida S/PDIF
Compatible con Direct Sound 3DTM
Multi-Language Translation
Español
Esta placa principal usa un tipo LGA775 de Pentium 4 que lleva las sigtes. características:
•
Acomoda los últimos procesadores Intel P4/Celeron
•
Soporta un bus de sistema (FSB) de 800/533MHz
•
Soporta la CPU con tecnología "Hyper-Threading"
Gráficas
•
•
•
•
•
•
3D setup y motor de rendimiento
Meojamiento de gráficas 2D/3D
Vídeo DVD/PV-VCR
Motor de textura de alta calidad
Soporte de Rendimiento de Zona
Solapado de Vídeo
Opciones de Expansión
Español
La placa principal viene con las sigtes. opciones de expansión:
•
Tres ranuras PCI de 32-bit
•
Una ranura AGP Express
•
Dos conectores SATA de 7-pin
•
Dos conectores IDE que soporta hasta cuatro dispositivos IDE
•
Una interfaz de la unidad de disco floppy
•
Una ranura CNR optativa
Esta placa principal soporta Ultra DMA bus mastering con índices de transferencia de 100/66/
33MB/s.
LAN Abordo (optativo)
El LAN abordo provee las sigtes. características:
•
Soporta operación de Autonegociación N-Way de 10Mb/s y 100Mb/s
•
Medio y Full Duplex
•
Soporta la función Wake-On-LAN y despertar remoto
•
Soporta Full Duplex Flow Control (IEEE 802.3x)
I/O Integrado
La placa principal tiene un juego completo de puertos y conectores I/O:
•
Dos puertos PS/2 para ratón y teclado
•
Un puerto serial
•
Un puerto paralelo
•
Cuatro puertos USB
•
Un puerto VGA
•
Un puerto LAN (optativo)
•
Un puerto 1394 (optativo)
•
Clavijas de audio para micrófono, entrada y salida de línea
BIOS Firmware
Esta placa principal usa Award BIOS que permite a los usuarios a configurar muchas
características de sistema que incluyen las sigtes.:
•
Administración de Alimentación
•
Parámetros de CPU
•
Cronometraje de CPU y de memoria
También se lo puede usar el firmware para configurar los parámetros para diferentes velocidades
de reloj de procesador.
Algunas especificaciones de hardware e ítems de software son sujetos a cambio
sin aviso previo.
Multi-Language Translation
Características
Processador
Conjunto de Chips
Os conjuntos de chips 865GV(GMCH) Northbridge (NB) da Intel e 82801EB(ICH5)
Southbridge (SB) são baseados numa arquitectura inovadora e escalável com fiabilidade e
performance provadas.
•
Suporta processadores P4/Celeron com taxa de transferência
865GV (NB)
de dados até 800/533/400MHz
•
Suporta DDR SDRAM a 400/333/266MHz
•
AGTL+Host Bus com Terminação Integrada Suportando
Endereçamento Host de 32 Bits
•
Interface Hub de 8 bits/66MHz 8X para Intel ICH5
•
Fornece um acelerador de gráficos integrado permitindo 3D,
2D rentáveis e capacidades de vídeo.
ICH5 (SB)
•
•
•
•
•
Suporta até seis PCI Masters que cumprem na totalidade
com a especificação PCI 2.3 a 33MHz
Suporta 2 canais com controladores IDE Ultra ATA 100 bus
master
Suporta dois Controladores Host ATA de Série
Cumpre com a AC’97 v2.3 suportando 6 Canais de saídas
áudio
Suporta oito portas USB 2.0 para transferências de série a
480Mb/s no máximo
Memória
Este controlador de memória pode acomodar até quatro 2.5V DIMM DDR SDRAM,
suportando DDR400/333/266MHz com uma capacidade máxima de memória de
4GB.
Codec Áudio
•
•
•
•
•
CODEC duplo completo estéreo de 16 bit com taxa de amostragem de
48KHz
Cumpre com especificação AC’97 v2.3
Suporta taxa de amostragem dupla (96KHz) de reprodução áudio de DVD
Suporta entrada S/PDIF e função de saída
Compatível com Direct Sound 3DTM
Multi-Language Translation
Português
Esta motherboard usa um tipo de Pentium 4 LGA775 que possui as seguintes características:
•
Acomoda os processadores Intel P4/Celeron mais recentes
•
Suporta um bus de sistema (FSB) de 800/533MHz
•
Suporta CPU de tecnologia “Hyper Threading”
Tecnologia “Hyper Threading” que permite ao sistema funcionar de forma interligada até
dois processadores, permitindo que os dois fios possam funcionar em paralelo, ambos em
processadores “lógicos” separados dentro do mesmo processador físico.
Gráficos
•
•
•
•
•
•
Instalação 3D e dispositivo de distribuição
Melhoramento de gráficos 2D/3D
Vídeo DVD/PV-VCR
Dispositivo de textura de elevada qualidade
Suporte de Distribuição de Zona
Cobertura de Vídeo
Opções de Expansão
Português
A motherboard é fornecida com as seguintes opções de expansão:
•
Três ranhuras PCI de 32 bit
•
Uma ranhura AGP Express
•
Dois conectores SATA de 7 pin
•
Dois conectores IDE que suportam até quatro dispositivos IDE
•
Um interface com drive de disco flexível
•
Uma ranhura CNR opcional
Esta motherboard suporta mastering bus Ultra DMA com taxas de transferência de 100/66/33MB/
s.
Onboard LAN (opcional)
O onboard LAN fornece as seguintes características:
•
Suporta operação de Auto-negociação N-Way 100Mb/s e10Mb/s
•
Duplo e Duplo Completo
•
Suporta função LAN de Despertar e despertar remoto
•
Suporta Controlo de Fluxo Duplo Completo (IEEE 802.3x)
I/O Integrado
A motherboard possui um conjunto completo de portas I/O e conectores:
•
Duas portas PS/2 para rato e teclado
•
Uma porta de série
•
Uma porta paralela
•
Quatro portas USB
•
Uma porta VGA
•
Uma porta LAN (opcional)
•
Uma porta 1394 (opcional)
•
Fichas áudio para microfone, entrada de linha e saída de linha
Microprogramação BIOS
Esta motherboard usa Award BIOS que permitem aos utilizadores configurar muitas características
do sistema incluindo as seguintes:
•
Gestão de corrente
•
Parâmetros CPU
•
Temporização de memória e CPU
A microprogramação poderá ser também usada para estabelecer parâmetros para diferentes
velocidades de relógio do processador.
Algumas especificações de hardware e itens de software poderão ser sujeitos a
alteraçõessem aviso prévio.
Multi-Language Translation
機能
プロセッサ
このマザーボードにはLGA775 タイプのPentium 4 を取り付け可能で、次の特徴があ
ります:
•
Intel P4 /Celeron プロセッサに対応
•
800/533 MHzのシステムバス(FSB)をサポート
•
“ハイパースレッド” 技術をサポート
ハイパースレッド(HT) 技術というのは、オペレーションシステムに2つのプロセッサが存
在すると認識させることで、実際には2つのスレッドを1つのプロセッサで同時に執行させ
、平行利用を可能とする技術です。
チップセット
865GV (NB)
• データ転送率が800/533/400MHzのP4/Celeron プロセッサ
に対応
• 400/333/266 MHz の DDR-SDRAM に対応
• 終端統合済みのAGTL+ホストバスで32ビットのホストアドレシン
グをサポート
• Intel ICH5への8ビット/66MHz 8X ハブインターフェースを導
入
• 統合型グラフィックアクセラレータを搭載し、手軽に3D、2D、お
よびビデオなどの機能を入手可能に
ICH5 (SB)
•
6つのPCI Masterに対応、33MHzではPCI 2.3 規格に完全
準拠
2 チャネルのUltra ATA 100 バスマスタ IDE コントローラ
をサポート
2つのシリアル ATA ホストコントローラをサポート
6つチャネルのオーディオ出力をサポートするAC’97 v2.3に
準拠
最大480Mb/秒のシリアル転送率可能の8つのUSB2.0ポー
ト
•
•
•
•
メモリ
このメモリコントロールでは、4つまでの2.5V DIMM DDR SDRAMを搭載可能で、
DDR400/333/266MHzをサポートします。最大4GBまでのメモリー容量を搭載可能で
す。
Audio CODEC
•
•
•
•
•
16ビットのステレオ全二重CODECで、48KHzサンプリングレートを導入
AC’97 v2.3仕様に準拠
DVDオーディオ信号再生のダブルサンプリングレート(96KHz) をサポート
S/PDIF入出力機能に対応
Direct Sound 3DTM に対応
Multi-Language Translation
日本語
Intel 865GV(GMCH)Northbridge (NB)と82801EB Southbridge (SB)チップセッ
トは、実証された信頼性と性能を持つ革新的で拡張性のあるアーキテクチャに基づいて
います。
グラフィック
•
•
•
•
•
•
3Dセットアップ&レンダーエンジンを導入
2D/3D グラフィック強化機能を導入
ビデオDVD/PV-VCRに対応
高品質テクスチャエンジンを導入
ゾーンレンダリング機能をサポート
ビデオオーバーレイ(Video Overlay)機能を導入
拡張オプション
本マザーボードでは、次の拡張機能が利用できます。
日本語
• 32ビットPCIスロット x3
• AGP Expressスロットx1
• 7ピンSATAコネクタ X2
• IDEヘッダー x2 (4つのIDEデバイスの接続を可能)
• フロッピーディスクドライブインターフェイス x1
• オプションのCNRスロットx1
このマザーボードは、100/66/33MB/秒の転送速度でのUltra DMAバスマスタリングを
サポートします。
オンボードLAN (オプション)
オンボードLANは、次の機能を提供します。
•
•
•
•
10Mb/秒および100Mb/秒N-way自動ネゴシエーション操作をサポート
半/全二重の動作が可能
Wake-On-LANと遠隔wake-up機能をサポート
全二重フロー制御(IEEE 802.3x)をサポート
統合の入出力ポート
マザーボードには、次のI/Oポートやコネクタを揃えています。
•
•
•
•
•
•
•
•
マウスとキーボード用のPS/2ポート x2
シリアルポート x1
パラレルポート x1
USBポート x4
VGAポート x1
LANポート x1(オプション)
1394ポート x1(オプション)
マイク、ラインイン、ラインアウト用オーディオジャック
BIOSファームウェア
本マザーボードはAward BIOSを採用し、次の機能を含む多様なシステムの構成ををサ
ポートします。
• 電源管理
• CPUパラメータ
• CPUとメモリとのタイミング
さらに、所定のパラメータを設定することによって、プロセッサのクロック速度を変更す
ることもできます。
一部のハードウェア仕様とソフトウェアアイテムは、予告なしに変更すること
があります。
Multi-Language Translation
특성
프로세서
본 마더보드는 팬티엄 4 의 LGA775 을 사용하며 다음과 같은 특성을 지닙니다:
•
최신 인텔 P4/샐러론 프로세서 사용
•
800/533MHz 의 시스템 버스 (FSB) 지원
•
"Hyper-Threading" 기술의 CPU 지원
“Hyper-Threading" 기술은 운영 체제가 두개의 프로세서에 연결되어 있는 것처럼,
두 트래드가 동일한 물리적 프로세서 안에 있으면서도 각기 다른 "논리적" 프로세서에
서 패러럴로 실행되게 한다.
칩셋
865GV (NB)
•
•
•
•
•
ICH5 (SB)
•
•
•
•
•
최대 데이터 전송 속도 800/533/400MHz 의 P4/샐러론 프로
세서 지원
400/333/266MHz 로 DDR SDRAM 지원
통합 터미네이션 지원 32 비트 호스트 어드레싱의
AGTL+Host Bus
인텔 ICH5의 8 비트/66MHz 8X 허브 인터페이스
비용 효율적인 3D, 2D 및 비디오 기능을 지닌 통합 그래픽 가
속기 제공.
33MHz 에서 PCI 2.3 사양과 부합하는 최대 6 개의 PCI 마
스터 지원
2 채널 Ultra ATA 100 버스 마스터 IDE 컨트롤러 지원
2 개의 Serial ATA 호스트 컨트롤러 지원
오디오 출력 6 채널을 지원하는 AC’97 v2.3 와 부합
최대 480Mb/s 로 시리얼 전송을 실행하는 8 개의 USB 2.0
포트 지원
메모리
본 메모리 컨트롤러는 최대 4 개의 2.5V DIMM DDR SDRAM를 사용하여, DDR400/
333/266MHz, 최대 메모리 용량 4GB 지원
오디오 코덱
•
•
•
•
•
샘플링 속도 48KHz 의 16 비트 스테레오 full-duplex 코덱
AC’97 v2.3 사양 부합
DVD 오디오 재생에 더블 샘플링 속도 (96KHz) 지원
S/PDIF 입력 및 출력 기능 지원
Direct Sound 3DTM 호환
Multi-Language Translation
한국어
인텔의 865GV(GMCH) Northbridge (NB) 및 82801EB(ICH5) Southbridge (SB) 칩셋
은 혁신적이고 범위성을 지닌 아키텍쳐를 바탕으로 하여 인정된 신뢰성과 성능을 지
닌다.
그래픽
•
•
•
•
•
•
3D 설정 및 랜더 엔진
2D/3D 그래픽 강화
비디오 DVD/PV-VCR
고품질 텍스처 엔진
Zone 랜더링 지원
비디오 오버레이
확장 옵션
본 마더보드의 확장 옵션은 다음과 같다:
•
32 비트 PCI 슬롯 3 개
•
AGP Express 슬롯 1 개
•
7 핀 SATA 커넥터 2 개최대
•
4 개의 IDE 장치를 지원하는 IDE 커넥터 2 개
•
플로피 디스크 드라이브 인터페이스 1 개
•
선택적 CNR 슬롯 1 개
본 마더보드는 전송 속도 100/66/33MB/s 로 Ultra DMA 버스 마스터링을 지원한다.
한국어
보드 내장 LAN (선택 사항)
보드 내장 LAN 은 다음과 같은 특성이 있다:
•
10Mb/s 및 100Mb/s N-Way Auto-negotiation 작업 지원
•
Half 및 Full 듀플렉스
•
Wake-On-LAN 기능 및 원격 wake-up 지원
•
Full Duplex Flow Control (IEEE 802.3x) 지원
통합 I/O
본 마더보드는 풀 셋트의 I/O 포트 및 커넥터가 있다:
•
마우스 및 키보드용 PS/2 포트 2 개
•
시리얼 포트 1 개
•
패러럴 포트 1 개
•
USB 포트4 개
•
VGA 포트1 개
•
LAN 포트 1 개 (선택 사항)
•
1394 포트 1 개 (선택 사항)
•
마이크, 라인 입력 및 라인 출력용 오디오 잭
BIOS 펌웨어
본 마더보드는 다음과 같은 시스템 특성을 구성할 수 있는 Award BIOS 를 사용한다:
•
전원 관리
•
CPU 파라미터
•
CPU 및 메모리 타이밍
펌웨어로 다른 프로세서 클록 속도의 파라미터를 설정할 수도 있다.
몇 하드웨어 사양 및 소프트웨어 아이템은 사전 통보 없이 변경될 수 있습
니다.
Multi-Language Translation
功能
處理器
本主機板㊜用於LGA775 型Pentium 4 且具㈲如㆘功能:
•
支援Intel P4 /Celeron 處理器;
•
支援高達800/533MHz之系統匯流排(FSB);
•
支援使用超執行緒(Hyper-Threading)技術之CPU。
利用“超執行緒(HT)”技術,可使作業系統在相當於裝㆖了兩具處理器的狀態㆘運作
:利用㆒個”實體”處理器模擬出兩個獨立的”邏輯”處理器,同時執行兩個工作緒
。
晶片組
865GV (NB)
•
•
•
•
•
支援傳輸率高達800/533/400MHz的P4/Celeron 處理器;
支援400/333/266 MHz的DDR-SDRAM;
具㈲內建終結的AGTL+主控匯流排,支援32位元主控定址;
具㈲8位元/66MHz 8X 匯流排介面,連接Intel ICH5;
整合㈲㆒繪圖加速器,藉此提供低成本3D、2D 及視訊相容
性。
ICH5 (SB)
•
支援高達6個的PCI 主控擴充槽,完全相容於33MHz的 PCI
2.3 規格;
支援2通道的Ultra ATA 100 匯流排主IDE 控制器;
支援2個Serial ATA主控器;
相容於AC'97 v2.3,可支援6聲道之音訊輸出;
支援8個USB 2.0埠,提供高達480Mb/秒之串列傳輸速度。
•
•
•
•
記憶體
在本記憶體控制器㆖,可安裝4組2.5V DIMM DDR SDRAM,支援DDR400/333/266MHz,最
大可安裝記憶體容量為4GB。
音頻編碼器
‧
‧
‧
‧
‧
16位元立體聲全雙工CODEC,提供48KHz取樣率;
相容於AC'97 v2.3規格;
支援DVD音訊播放時的雙採樣率 (96KHz);
支援 S/PDIF輸出入功能;
Direct Sound 3DTM 相容。
Multi-Language Translation
繁體㆗文
Intel 865GV(GMCH)北橋(NB)及82801EB(ICH5)南橋(SB)晶片組在研發設計㆖採用了創新
且具擴充性之架構,具備㊝良的可靠性及性能。
繪圖卡
‧
‧
‧
‧
‧
‧
3D算圖引擎;
2D/3D圖形強化功能;
視訊DVD/PV-VCR;
高品質紋理引擎;
支援區域繪圖成形(Zone Rendering)功能
影像重疊(Video Overlay)功能
擴充選㊠
本主機板包括㆘列擴充選㊠:
•
•
•
•
•
•
3
1
2
2
1
1
個 32-bit PCI 插槽;
個 AGP Express 插槽 ;
個7針SATA插頭
個 IDE 接頭,支援 4個 IDE 裝置;
個軟碟機介面;
個選㊠CNR槽。
本主機板支援傳輸率100/66/33 MB/秒㆘的Ultra DMA 匯流排主控功能。
內建區域網路 (選購)
繁體㆗文
內建區域網路提供㆘列功能:
•
•
•
•
支援 10Mb/s 及 100Mb/s N-way ㉂動㈿調作業;
支援半/全雙工;
支援區域網路喚醒(Wake-On-LAN)及遠端喚醒功能;
支援全雙工流量控制(IEEE 802.3x)。
整合 I/O
主機板具㈲㆒組齊全的 I/O 連接埠及連接頭:
• 2 個 PS/2 埠,供滑鼠與鍵盤使用;
• 1 個串列埠;
• 1 個平行埠;
• 4 個USB埠;
• 1 個VGA埠;
• 1 個區域網路埠(選購);
• 1 個1394埠(選購);
• 麥克風音頻插座、線級輸入及線級輸出。
BIOS 韌體
本主機板使用Award BIOS,使用者可以組態設定許多系統功能,包括如㆘:
• 電源管理;
• CPU參數;
• CPU及記憶體的時脈定時。
此外,也可藉由參數的設定,調整處理器的時脈速度。
部份硬體規格和軟體內容可能會在未經通知的情況㆘更動,敬請見諒。
Multi-Language Translation
功能
处理器
此主板使用 LGA775 型 Pentium 4 CPU,具备以下特点:
•
支持最新的 Intel P4/Celeron 处理器
•
支持 800/533 MHz 系统总线 (FSB)
•
支持“多线程”技术 CPU
“多线程”技术可以让操作系统认为自己连接了两个处理器,允许两个线程并行运行
,每个线程位于同一处理器中的单独“逻辑”处理器中。
芯片组
Intel 865GV(GMCH) 北桥 (NB) 和 82801EB(ICH5) 南桥 (SB) 芯片组是基于一种新型
的、可扩展的架构,能提供已经证明的可靠性和高性能。
•
•
•
•
•
ICH5 (SB)
•
•
•
•
•
支持 P4/Celeron 处理器,数据传输速率可达 800/533/
400MHz
支持在 400/333/266MHz 下工作的 DDR-SDRAM
AGTL+ 带有综合终端的主控总线,支持 32 位主机寻址
到 Intel ICH5 的 8-位/66MHz 8X 集线器接口
提供集成图形加速器,高性价比 3D、2D 和视频功能
支持 6 个 PCI 主控器,完全符合 PCI 2.3 规格(
33MHz)
支持 2 通道 Ultra ATA 100 总线主控 IDE 控制器
支持 2 个串行 ATA 主控器
符合 AC’97 v2.3 规格,支持 6 声道音频输出
支持 8 个用于串行传输的 USB 2.0 端口,最大速率
480Mb/s
内存
此内存控制器可以支持 4 个 2.5V DIMM DDR SDRAM,支持 DDR400/333/266MHz,
最大内存可支持 4GB。
音频编解码器
•
•
•
•
•
具有
兼容
支持
支持
符合
48KHz 采样速率的 16 位全双工 CODEC(编解码器)
AC’97 v2.3 规格
DVD 音频播放的双采样速率 (96KHz)
S/PDIF 输入和输出功能
Direct Sound 3DTM 规格
Multi-Language Translation
简体中文
865GV (NB)
图形
•
•
•
•
•
•
3D 设置和着色引擎
2D/3D 增强图形
视频 DVD/PV-VCR
高性能纹理引擎
支持区域着色
视频覆盖
扩展选项
此主板提供如下扩展选项:
•
3 个 32 位 PCI 扩展插槽
•
1 个AGP Express 槽
•
2 个 7-pin SATA 接口
•
2 个 IDE 接口,可支持 4 个 IDE 设备
•
1 个软驱接口
•
1 个 可选 CNR 插槽
主板支持 Ultra DMA 总线控制,传输速率可达 100/66/33MB/s。
Onboard LAN(可选)
简体中文
板上集成的 LAN 提供以下功能:
•
支持 10Mb/s 和 100Mb/s N 路自协商工作
•
半双工和全双工
•
支持 LAN 唤醒 (WOL) 功能和远程唤醒功能
•
支持全双工流控制 (IEEE 802.3x)
集成 I/O
此主板具有完整的 I/O 端口和插孔:
•
2 个用于连接鼠标和键盘的 PS/2 端口
•
1 个串口
•
1 个并口
•
4个 USB 端口
•
1个 VGA 端口
•
1 个 LAN 端口(可选)
•
1 个 1394 端口(可选)
•
麦克风、线入和线出声音插孔
BIOS
此主板使用 Award BIOS,可以让用户自己配置以下系统功能:
•
电源管理
•
CPU 参数
•
CPU 和记忆定时
还可用于设置不同处理器时钟速度的参数。.
某些硬件规格和软件项目若有更改恕不另行通知。
Multi-Language Translation
Характеристики
Процессор
Плата построена на базе процессора Pentium 4 LGA775 и обладает следующими
характеристиками:
•
Поддерживает новейшие процессоры Intel P4/Celeron
•
Поддерживает системные шины (FSB) с частотой 800/533MHz
•
Поддерживает технологию CPU “Hyper-Threading”
Технология “Hyper-Threading” «убеждает» операционную систему в том, что в машине
имеется два процессора; это позволяет параллельно обслуживать два процесса, причем
каждый из процессов обслуживается отдельным «логическим» процессором в пределах
одного физического процессора.
Чипсет
ICH5 (SB)
•
Поддержка до шести устройств PCI Master при полной
совместимости со спецификацией PCI 2.3 / 33MHz
Поддержка 2 каналов IDE контроллера Ultra ATA 100
bus master
Поддержка двух хост-контроллеров Serial ATA
Совместимость с AC’97 v2.3, поддержка 6-канального
аудиовыхода
Поддержка восьми портов USB 2.0 для серийной
передачи данных с максимальной скоростью 480Mб/
сек
•
•
•
•
Память
Контроллер памяти может обслуживать до четырех 2.5V DIMM DDR SDRAM,
поддерживает DDR400/333/266MHz при максимальном объеме памяти 4GB.
Аудио CODEC
•
•
•
•
•
16-битовый стерео КОДЕК full-duplex с частотой сэмплирования
48KHz
Совместим со спецификацией AC’97 v2.3
Поддержка режима двойного сэмплирования (96KHz) при
прослушивании аудио-DVD
Поддержка функции входа/выхода S/PDIF
Совместимость с Direct Sound 3DTM
Multi-Language Translation
Русский
Чипсеты Intel 865GV(GMCH) «Северный мост» (Northbridge, NB) и 82801EB(ICH5)
«Южный мост» (Southbridge, SB) построены с использованием инновационной
масштабируемой архитектуры, обеспечивающей высокую надежность и
производительность.
865GV (NB)
•
Поддерживает процессоры P4/Celeron со скоростью
передачи данных до 800/533/400MHz
•
Поддерживает память DDR SDRAM с частотой 400/
333/266MHz
•
AGTL+Host Bus с интегрированной поддержкой
терминации 32-битной адресации хоста
•
Интерфейс 8-бит/66MHz 8X Hub для Intel ICH5
•
Интегрированный высокопроизводительный
акселератор 3D, 2D и видеографики
Графика
•
•
•
•
•
•
Процессор трехмерной графики (3D setup and render)
Расширение графики 2D/3D
Видео DVD/PV-VCR
Процессор высококачественных текстур
Поддержка технологии Zone Rendering
Поддержка режима Video Overlay
Возможности расширения
Существуют следуюшие опции расширения данной материнской платы:
•
Три 32-битовых слота PCI
•
Один слот AGP Express
•
Два разъема 7-pin SATA
•
Два разъема IDE с поддержкой до четырех устройств IDE
•
Один разъем для накопителя на гибких дисках
•
Опционально один слот CNR
Плата поддерживает захват управления шиной Ultra DMA со скоростью передачи 100/
66/33MБ/с.
Встроенный сетевой адаптер LAN (опционально)
Встроенный сетевой адаптер LAN обладает следующими характеристиками:
•
Поддерживает автоматическое определение скорости и режима
соединения 10Mb/s и 100Mb/s
•
Поддержка режимов Half и Full Duplex
•
Поддерживает функции Wake-On-LAN и remote wake-up
•
Поддерживает режим управления потоком Full Duplex Flow Control
(IEEE 802.3x)
Интегрированный вход/выход
Русский
Плата снабжена полным набором портов входа/выхода и разъемов:
•
Два порта PS/2 для подключения мыши и клавиатуры
•
Один серийный порт
•
Один параллельный порт
•
Четыре порта USB
•
Один порт VGA
•
Один порт LAN (опционально)
•
Один порт 1394 (опционально)
•
Гнездо для подключения микрофона, гнезда аудио-входа и выхода
BIOS
Плата работает под Award BIOS, который позволяет пользователю конфигурировать
различные характеристики системы:
•
Управление питанием
•
Параметры CPU
•
Время доступа для CPU и памяти
BIOS допускает также установку параметров для различных частот процессора.
Некоторые параметры платы и характеристики ее программного
обеспечения могут быть изменены без предварительного уведомления.
Multi-Language Translation
Cechy
Procesor
Ta płyta główna zaopatrzona jest w procesor Pentium 4 typu LGA775 i charakteryzuje się
następującymi cechami:
•
Obsługuje najnowsze procesory Intel P4/Celeron
•
Obsługuje szynę systemowa (FSB) 800/533MHz
•
Zabezpiecza technologię CPU “Hyper-Threading”
Technologia “Hyper-Threading” powoduje, że system "myśli”, że posiada dwa procesory i
wykonuje równolegle dwa procesy; za wykonanie każdego procesu odpowiedzialny jest jeden
z dwuch "logicznych" procesorów w ramach jednego fizycznego procesora
Chipset
Mostek północny (NB) Intel 865GV(GMCH) i mostek południowy 82801EB(ICH5) chipsetu
oparty jest na nowatorskiej i skalowalnej architekturze o sprawdzonej niezawodności i
funkcjonalności.
•
•
•
•
•
ICH5 (SB)
•
•
•
•
•
Współpracuje z procesorami P4/Celeron o szybkościach
transferu danych odpowiednio 800/533/400MHz
Obsługuje pamięć DDR SDRAM typu 400/333/266MHz
AGTL+Host Bus ze zintergrowanym zakończeniem
obsługującym 32-bitowe adresowanie hosta
8-bits/66MHz 8X interfejs dla Intelowskiego mostka ICH5
Zapewnia zintegrowany przyśpieszacz graficzny
zapewniający w niekosztowny sposób możliwości grafiki
3D, 2D i wideo
Obsługuje do sześciu urządzeń PCI, zgodny całkowicie ze
specyfikacją PCI 2.3 o częstotliwości 33MHz
Obsługuje 2 kanały Ultra ATA 100 szyny głównej kontrolera
IDE
Obsluguje dwa szeregowe kontrolery ATA
Zgodny z AC’97 v2.3, obsługuje 6-kanałowe wyjście audio
Obsługuje osiem gniazd USB 2.0 umożliwiających transfer
danych do szybkości 480Mb/s (maksymalnie)
Pamięć
Zastosowany kontroler pamięci może obsłużyć do czterech kostek pamięci typu
2.5V DIMM DDR SDRAM, pracujących na szybkościach DDR400/333/266MHz i
maksymalnej pojemności pamięci do 4 GB
Audio CODEC
•
•
•
•
•
16-bitowe stereo full-duplex CODEC z 48KHz próbkowaniem
Zgodny z AC’97 w wersji 2.3
Obsługuje podwójne próbkowanie (96KHz) DVD audio playback
Obsługuje funkcję S/PDIF wejścia i wyjścia
Zgodny z Direct Sound 3DTM
Multi-Language Translation
Polski
865GV (NB)
Grafika
•
•
•
•
•
•
Procesor 3D setup and render
Rozszerzona grafika 2D/3D
Video DVD/PV-VCR
Procesor tekstur wysokiej jakości
Obsługuje technologię Zone Rendering
Obsługuje tryb Video Overlay
Możliwości rozbudowy
Płyta głwna wyposażona jest w następujące gniazda:
•
Trzy 32-bitowe gniazda PCI
•
Jedno gniazdo AGP Express
•
Dwa 7-nóżkowe złącza SATA
•
Dwa złącza IDE mogące obsłużyć do czterech urządzeń IDE
•
Jedno złącze obsługujące stacje dyskietek
•
Jedno gniazdo CNR opcjonalnie
Płyta głwna obsługuje magistralę Ultra DMA o szybkościach przesyłu 100/66/33MB/s.
Zintegrowana obsługa sieci LAN (opcjonalnie)
Zintegrowana obsługa sieci LAN posiada następujące właściwości:
•
Obsluguje N-drożne automatycznie ustalane operacje z szybkościami 10Mb/s
i 100Mb/s
•
Zdolność Half/Full duplex
•
Obsługuje funkcję Wake-On-LAN i zdalnie sterowane wake-up
(uruchamianie komputera)
•
Obsługuje Full Duplex Flow Control (zgodnie ze standardem IEEE 802.3x)
Zintegrowane We/Wy
Polski
Płyta głwna wyposażona jest w pełny zestaw gniazd i złączy We/Wy:
•
Dwa gniazda PS/2 dla myszy i klawiatury
•
Jedno gniazdo szeregowe
•
Jedno gniazdo równoległe
•
Cztery gniazda USB
•
Jedno gniazdo VGA
•
Jedno gniazdo LAN (opcjonalnie)
•
Jedno gniazdo 1394 (opcjonalnie)
•
Gniazdo wejściowe mikrofonowe, gniazdo wejściowe i wyjściowe dzwięku
(audio)
Firmowy BIOS
Płyta głwna wyposażona jest w BIOS firmy Award, który pozwala użytkownikowi
konfigurować wiele cech systemu włączając w to następujące właściwości:
•
Zarządzanie poborem mocy
•
Parametry pracy procesora
•
Ustalenia szybkoœci pracy procesora i pamiêci
BIOS może być używany do ustalania parametrów wpływających na szybkości pracy zegara
procesora.
Niektóre parametry dotyczące płyty i jej oprogramowania mogą ulec zmianie
bez uprzedniego powiadomienia.
Multi-Language Translation
Vlastnosti
Procesor
Tato základní deska je určena pro procesory Pentium 4 LGA775 a může nabídnout následující
vlastnosti:
•
Základní deska je určena pro nejnovější procesy Intel P4/Celeron
•
Podporuje taktování systémové sběrnice (FSB) na frekvenci 800/533 MHz
•
Podporuje technologii CPU „Hyper-Threading“
Technologie „Hyper-Threading“ umožňuje operačnímu systému pracovat tak, jako by byl
připojen ke dvěma procesorům, protože je možné pracovat se dvěma toky programového
kódu (vlákny) paralelně najednou, přičemž jsou k dispozici samostatné „logické“ procesory
umístěné v rámci jednoho fyzického procesoru.
Čipová sada
Čipová sada Intel 865GV(GMCH) s northbridge (NB) a southbridge (SB) 82801EB(ICH5) je
založena na inovativní a škálovatelné architektuře s ověřenou spolehlivostí a výkonem.
•
•
•
•
•
ICH5 (SB)
•
•
•
•
•
Podporuje procesory P4/Celeron s přenosovými rychlostmi
800/533/400 MHz
Podporuje DDR SDRAM s frekvencí 400/333/266 MHz
Hostitelská sběrnice AGTL+ s integrovaným ukončením
podporujícím 32bitové adresování hostitele
8bitové/66 MHz 8x rozhraní rozbočovače dle Intel ICH5
Integrovaný grafický akcelerátor nabízející nákladově
efektivní možnosti 3D, 2D grafiky a přehrávání videa.
Podporuje až šest PCI Master, plně dle standardu PCI 2.3
na frekvenci 33 MHz
Podporuje 2 kanály sběrnice Ultra ATA 100 s řadičem IDE
Podporuje dva řadiče rozhraní Serial ATA
Splňuje požadavky standardu AC’97 v2.3, podporuje 6
výstupních audio kanálů
Podporuje osm portů USB 2.0 pro sériový přenos dat
maximální rychlostí 480 Mb/s
Paměť
Řadič operační paměti dokáže spolupracovat až se čtyřmi moduly DIMM DDR
SDRAM napájenými napětím 2,5 V, přičemž podporuje DDR400/333/266 MHz a
maximální kapacitu paměti až 4GB.
Audio kodek
•
•
•
•
•
16bitový stereo plně duplexní kodek se vzorkovací frekvencí 48 kHz
Splňuje požadavky standardu AC’97 v2.3
Podpora dvojnásobné vzorkovací frekvence (96 kHz) pro přehrávání DVD
audio
Podporuje vstupní a výstupní funkce S/PDIF
Kompatibilita s Direct Sound 3DTM
Multi-Language Translation
Česky
865GV (NB)
Grafika
•
•
•
•
•
•
Renderovací grafické jádro 3D
Funkce vylepšující zobrazení 2D/3D grafiky
Video DVD/PV-VCR
Jádro pro zobrazování textur ve vysoké kvalitě
Podpora zónového renderování
Překrývání videa
Možnosti rozšíření
Základní deska je dodávána s následujícími možnostmi rozšíření
•
Tři 32bitové patice PCI
•
Jedna patice AGP Express
•
Dva 7kolíkové konektor SATA
•
Dva konektory IDE, podporující připojení až 4 zařízení IDE
•
Jedno rozraní pro disketovou mechaniku
•
Jedna volitelná patice CNR
Základní deska podporuje řízení sběrnice Ultra DMA s přenosovými rychlostmi 100/66/33
MB/s.
Vestavění síťové rozhraní LAN (volitelně)
Vestavěné síťové rozhraní LAN nabízí následující možnosti:
•
Podpora 10Mb/s a 100Mb/s N–cestného automatického přepínání
provozu
•
Poloviční a plný duplex
•
Podpora funkce Wake–On–LAN a aktivace na dálku
•
Podpora plně duplexního řízení toku dat (IEEE 802.3x)
Integrovaný vstup/výstup
Česky
Základní deska je vybavena kompletní sadou vstupních portů a konektorů I/O:
•
Dva porty PS/2 pro myš a klávesnici
•
Jeden sériový port
•
Jeden paralelní port
•
Čtyři porty USB
•
Jeden port VGA
•
Jeden port LAN (volitelně)
•
Jeden port 1394 (volitelně)
•
Zvukové konektory pro mikrofon, zvukový vstup a výstup
Firmware BIOS
Základní deska využívá BIOS formy Award, který uživateli umožňuje nakonfigurovat mnoho
systémových parametrů, včetně následujících:
•
Řízení spotřeby
•
Parametry CPU
•
Časování CPU a paměti
Firmware může být rovněž použit k nastavení parametrů pro různé taktovací frekvence
procesoru.
Některé technické parametry hardware a software se mohou měnit bez
předchozího upozornění.
Multi-Language Translation
Caracteristici
Procesorul
Această placă de bază utilizează Pentium 4 de tipul LGA775, având următoarele
caracteristici:
•
Este destinată celor mai recente procesoare Intel P4/Celeron
•
Funcţionează cu bus sistem (FSB) de 800/533 MHz
•
Este compatibilă cu unităţi centrale dotate cu tehnologia „HyperThreading”
Tehnologia „Hyper-Threading” permite sistemului de operare să funcţioneze ca şi cum
ar exista două procesoare, putând fi rulate în paralel două fire, fiecare pe câte un procesor
„logic” separat, aflate pe acelaşi procesor fizic.
Setul de chipuri
Seturile de chipuri 865GV(GMCH) Northbridge (NB) şi 82801EB(ICH5) Southbridge (SB)
se bazează pe o arhitectură inovatoare şi scalabilă, care s-a impus deja prin fiabilitate şi
performanţă.
•
•
•
•
•
ICH5 (SB)
•
•
•
•
•
Funcţionează cu procesoare P4/Celeron, având o viteză de
transfer a datelor de până la 800/533/400 MHz.
Este compatibilă cu unităţi de memorie DDR SDRAM de
400/333/266 MHz.
AGTL+Host Bus cu terminaţie integrată, sprijinind Host
Addressing (adresare gazdă) de 32 biţi
Interfaţă Hub 8X de 8 biţi/66 MHz pentru Intel ICH5
Include un accelerator grafic prin care asigură posibilităţi
economice 3D, 2D şi video.
Poate deservi până la şase masteri PCI pe deplin compatibile
cu specificaţia PCI 2.3 la 33 MHz
Permite utilizarea a 2 canale de controler IDE Ultra ATA
100 bus master
Utilizează doi controleri gazdă Serial ATA
Compatibil cu AC’97, versiunea 2.3, suportând 6 canale
audio de ieşire
Permite utilizarea a până la opt porturi USB 2.0, cu viteza
de transfer serial de cel mult 480 Mb/s
Memoria
Controlerul pentru memorii poate deservi până la patru unităţi DIMM DDR SDRAM
de 2,5 V, DDR400/333/266MHz, capacitatea maximă fiind de 4 GB.
Audio CODEC
•
•
•
•
•
CODEC stereo cu duplex complet pe 16 biţi, cu viteză de eşantionare de
48 kHz
Compatibil cu specificaţia AC’97, versiunea 2.3
Suportă frecvenţă de comutare dublă (96 kHz) pentru redarea audio de pe
DVD
Permite utilizarea funcţiei S/PDIF de intrare şi ieşire
Compatibil cu Direct Sound 3DTM
Multi-Language Translation
Română
865GV(NB)
Grafică
•
•
•
•
•
•
Motor de configurare şi randare 3D
Intensificare grafici 2D/3D
Video DVD/PV-VCR
Motor de texturare de înaltă calitate
Permite randare de zone
Suprapunere video
Opţiuni de extindere
Placa de bază este dotată următoarele posibilităţi de extindere:
•
Trei sloturi PCI de 32 biţi
•
Un slot AGP Express
•
Două conectoare SATA 7
•
Două conectoare IDE care deservesc patru unităţi IDE
•
O interfaţă pentru unitate floppy
•
Un slot opţional CNR
Această placă de bază suportă Ultra DMA bus mastering cu viteza de transfer de 100/66/
33MB/s.
Onboard LAN (opţional)
Onboard LAN are următoarele caracteristici:
•
Suportă operaţii de autonegociere N-way de 10 Mb/s şi 100 Mb/s
•
Posibilitate semi-duplex şi duplex complet
•
Suportă funcţia Wake-On-LAN şi trezirea de la distanţă
•
Suportă controlul proceselor de duplex total (IEEE 802.3x)
I/O integrată
Placa de bază este dotată cu un set complet de porturi şi conectoare I/O:
•
Două porturi PS/2, pentru mouse şi tastatură
•
Un port serial
•
Un port paralel
•
Patru porturi USB
•
Un port VGA
•
Un port LAN (opţional)
•
Un port 1394 (opţional)
•
Mufe audio pentru microfon, intrare şi ieşire audio
Română
Firmware BIOS
Această placă de bază utilizează Award BIOS, care permite utilizatorului să configureze mai
mulţi parametri ai sistemului, cum ar fi:
•
Gestionarea energiei
•
Parametri CPU
•
Temporizare CPU şi memorie
Acest firmware poate fi utilizat şi pentru a seta parametrii diferitelor frecvenţe de comandă ale
procesorului.
Anumite specificaţii hardware şi elemente de software pot fi modificate fără
înştiinţare prealabilă.
Multi-Language Translation
Спецификация
Процесор
Тази дънна платка използва Pentium 4 тип LGA775 със следните спецификации:
•
поддръжка на последни модели процесори Intel P4/Celeron
•
поддръжка на системна шина със скорост 800/533MHz
•
поддръжка на процесори с технология “Hyper-Threading"
Технологията “Hyper-Threading" позволява да се “излъже” операционната система, че
работи на два процесора, което дава възможност за паралелното изпълнение на две
задачи на два отделни “логически” процесора в един и същ физически процесор.
Чипсет
Чŕпсетът със северен мост Intel 865GV(GMCH) и южен мост 82801EB(ICH5) е
изграден на базата на оригинална архитектура с възможност за надстройка с доказана
надеждност и производителност.
865GV (NB)
•
•
•
•
•
ICH5 (SB)
•
•
•
•
•
поддръжка на процесори P4/Celeron с трансфер на данни
до 800/533/400MHz
поддържка на DDR SDRAM на скорост 400/333/266MHz
шина AGTL+Host с интегрирано завършване с
поддръжка на 32-Bits адресация
8-bits/66MHz 8X Hub интерфейс за Intel ICH5
Интегриран графичен ускорител, обезпечаващ
високоефективни 3D, 2D и видео възможности.
пълна съвместимост със спецификацията PCI 2.3
(на скорост 33MHz) с поддръжка до 6 PCI Master
устройства
поддръжка на двуканални Ultra ATA 100 bus master IDE
контролери
поддръжка на два Serial ATA Host контролера
съвместимост с AC’97 v2.3 с поддръжка на 6-канално
аудио
поддръжка на осем порта USB 2.0 за сериен трансфер
на максимална скорост 480Mb/s
Памет
Audio CODEC
•
•
•
•
•
16-bit Stereo full-duplex CODEC с честота 48KHz
съвместимост със спецификацията AC’97 v2.3
едновременно възпроизвеждане на 2 звукови потока (96KHz) на DVD
аудио
поддръжка на функцията S/PDIF вход/изход
съвместимост с Direct Sound 3DTM
Multi-Language Translation
Български
Контролерът на паметта поддържа четири 2.5V DIMM DDR SDRAM слота и
DDR400/333/266MHz с общ максимален капацитет 4GB.
Графичен чип
•
•
•
•
•
•
3D setup and render engine
подобрена графика 2D/3D
Video DVD/PV-VCR
висококачествено ядро за текстури
поддръжка на Zone Rendering
Video Overlay
Възможности за разширяване
Дънната платка има следните разширителни възможности:
•
три 32-bit PCI слота
•
един слот AGP Express
•
два 7-щифтови SATA конектораs
•
два IDE конектора с поддръжка до четири IDE устройства
•
един конектор за флопидисково устройство
•
един слот CNR (опция)
Дънната платка поддържа шина Ultra DMA 100/66/33MB/s.
Интегриран мрежов контролер (опция)
Спецификация на интегрирания мрежов контролер:
•
поддръжка на 10Mb/s и 100Mb/s, N-Way Auto-negotiation operation
•
Half и Full Duplex
•
поддръжка на функция за “събуждане” Wake-On-LAN и дистанционен
wake-up
•
поддръжка на Full Duplex Flow Control (IEEE 802.3x)
Интегриран Вход/Изход контролер
Дънната платка има пълен набор от I/O портове и конектори:
•
два PS/2 порта за мишка и клавиатура
•
един сериен порт
•
един паралелен порт
•
четири USB порта
•
един VGA порт
•
един LAN порт (опция)
•
един 1394 порт (опция)
•
Аудио жакове за микрофон, линеен вход и линеен изход
BIOS Firmware
Български
Дънната платка използва Award BIOS с възможност за различни системни настройки,
включително
•
управление на захранването
•
параметри на процесора
•
синхронизиране на процесора и паметта
настройка на скоростта на часовника на процесора
Хардуерните и софтуерни спецификации и параметри могат да бъдат
изменени без предупреждение.
Multi-Language Translation
Jellemző
Processzor
Ez az alaplap LGA775 típusú Pentium 4 számára készült, és a következő jellemzőkkel bír:
•
A legújabb Intel P4/Celeron processzorokkal működik
•
800/533 MHz sebességű rendszerbuszt (FSB) támogat
•
Támogatja a „Hyper-Threading” technológiát használó központi
egységeket
A „Hyper-Threading” technológia által az operációs rendszer úgy működik, mintha két
processzorral rendelkezne, ami két szál párhuzamos futását teszi lehetővé két független,
ugyanazon fizikai processzoron található „logikai” processzoron.
Lapkakészlet
Az Intel 865GV(GMCH) Northbridge (NB) és 82801EB(ICH5) Southbridge (SB)
lapkakészletek egy újító és méretezhető, nagy megbízhatóságú és teljesítőképességű
architektúrára épülnek.
865GV (NB)
•
•
•
•
•
ICH5 (SB)
•
•
•
•
•
P4/Celeron processzorokat támogat, 800/533/400 MHz-es
adatátviteli sebességgel
400/3330266 MHz-es DDR SDRAM memóriaegységeket
támogat
32 bites Host Addressing-et (gazdacímzés) támogató,
integrált lezárással rendelkező AGTL+Host Bus
8 bites/66 MHz-es 8X Hub interfész az Intel ICH5
esetében
Integrált grafikus gyorsítóval rendelkezik, amely
költséghatékony 3D, 2D és video lehetőségeket biztosít.
Akár hat, 33 MHz-en a 2.3-as PCI specifikációkkal teljesen
kompatibilis PCI mastert is támogat
2 Ultra ATA 100 bus master IDE vezérlő csatornát támogat
Két soros ATA gazdavezérlőt támogat
Kompatibilis az AC”97 2.3-as verziójával, maximum 6
audio kimenet csatornát támogat
Nyolc USB 2.0-s portot képes kiszolgálni, maximum
480 Mb/s soros átviteli sebességgel
Memória
A memóriavezérlő legtöbb négy 400/333/266 MHz átviteli sebességű, 2,5 V-os DIMM
DDR SDRAM memóriaegységet képes befogadni, maximális kapacitása 4 GB.
•
•
•
•
•
16 bites sztereo teljes duplex CODEC, 48 kHz-es mintavételezési
sebességgel
Kompatibilis az AC”97 2.3-as változatának szabványával
DVD audio lejátszás dupla mintavételezési arányú (96 kHz)
Támogatja az S/PDIF bemeneti és kimeneti funkciót
kompatibilis a Direct Sound 3DTM technológiával
Multi-Language Translation
Magyar
AC’97 Audio CODEC
Grafika
•
•
•
•
•
•
3D beállító és megjelenítő motor
2D/3D grafikus bővítés
Video DVD/PV-VCR
Kiváló minőségű mintázómotor
Zónamegjelenítés támogatása
Video átfedés
Bővítési lehetőségek
Az alaplap a következő bővítési lehetőségekkel rendelkezik:
•
Három 32 bites PCI foglalat
•
Egy AGP Express foglalat
•
Két 7 tűs SATA csatlakozó
•
Két IDE csatlakozó, amelyek négy IDE egységet tudnak kiszolgálni
•
Egy hajlékonylemez meghajtó interfész
•
Egy választható CNR foglalat
Ez az alaplap a 100/66/33MB/s átviteli sebességű Ultra DMA ’bus mastering’ megoldást is
támogatja.
Alaplapon levő LAN (választható)
Az alaplapon levő LAN jellemzői:
•
10Mb/s és 100Mb/s N-Way automatikus beállítással
•
Fél-/teljes duplex
•
Támogatja a Wake-On-LAN funkciót és a távoli ébresztést
•
Támogatja a teljes duplex folyamatvezérlést (IEEE 802.3x)
Beépített I/O
Az alaplapot az I/O portok és csatlakozók teljes készletével szerelték fel:
•
Két PS/2 port az egér és a billentyűzet számára
•
Egy soros port
•
Egy párhuzamos port
•
Négy USB port
•
Egy VGA port
•
Egy LAN port (választható)
•
Egy 1394-es port (választható)
•
Audio csatlakozók mikrofon, bemenet és kimenet számára
BIOS Firmware
Az alaplapon levő Award BIOS segítségével a felhasználó a rendszer sok paraméterét állíthatja
be, például:
•
Energiagazdálkodás
•
CPU paraméterek
•
CPU és memória időzítés
A firmware segítségével a processzor órajel-frekvenciáinak paramétereit is beállíthatják.
Magyar
Bizonyos hardverjellemzők és szoftverelemek előzetes bejelentés nélkül
módosulhatnak.
Multi-Language Translation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement