warning - Butaca Segura
Para instrucciones en Español, llamar al: 1-800-233-5921
OWNER’S MANUAL
Keep for future use.
Momentum
TM
Child Restraint System
Child Requirements
Weight: 5 – 65 lbs (2.3 – 29.4 kg)
Height: 19 – 50 in. (48 – 127 cm)
WARNING
To reduce the
risk of SERIOUS INJURY
or DEATH, read this
owner’s manual prior to
installing and using this
child restraint.
© Evenflo Company, Inc. 2010
25700522 7/10
Warnings............................................................................. 2
Safe Practices....................................................................... 9
Registry and Recall Information.......................................... 10
Airplane Usage................................................................... 10
LATCH Information............................................................ 10
Symbol Legend.................................................................. 11
Visual Glossary................................................................... 12
Securing the Child in the Child Restraint............................ 14
Removing the Child from the Child Restraint..................... 16
Important Information
Important Information
Rear-facing Use
Installation Checklist.......................................................... 19
Moving LATCH Connectors to Rear-facing......................... 20
Installation with SureLatch™ Connectors...................... 22
Installation with Quick Connectors™.............................. 26
Installation with Vehicle Seat Belt................................... 28
Rear-facing Use
For children who are
5 – 40 lbs (2.3 – 18 kg)
Forward-facing Use
For children who are
20 – 65 lbs (9 – 29.4 kg)
Installation Checklist.......................................................... 33
Moving LATCH Connectors to Forward-facing................... 34
Installation with SureLatch™ Connectors...................... 36
Installation with Quick Connectors™.............................. 42
Installation with Vehicle Seat Belt................................... 45
General Information
Operating the SureLatch™ Connectors.............................. 50
Operating the Quick Connect™......................................... 51
Adjusting the Recline Position............................................ 52
Removing Seat Pad............................................................ 52
Installing the Locking Clip.................................................. 53
Installing the Accessories.................................................... 55
Care and Cleaning ............................................................ 57
Replacement Parts............................................................. 59
Limited Warranty............................................................... 60
Forward-facing Use
• NOTICE •
•This child restraint meets all applicable requirements of
Federal Motor Vehicle Safety Standard 213.
• No restraint can guarantee absolute protection from
injury in every crash.
• This child restraint is designed for use by children in
rear-facing and forward-facing modes. To use this child
restraint properly, children MUST meet weight/size specifications as follows:
For Rear-facing Use
• The child weighs 5 – 40 lbs (2.3 – 18 kg)
• Top of child’s head is at least 1 inch (25 mm) below
the top of the child restraint.
For Forward-facing Use
• The child weighs 20 – 65 lbs (9 – 29.4 kg)
• The child is 50 inches (127 cm) tall, or less, AND the
top of their ears are at (or below) the child restraint.
•Child is one year old or older
Table of Contents
General Information
More children are killed every year as passengers in
car crashes than by any other type of injury.
To reduce the risk of SERIOUS INJURY or DEATH, read
this owner’s manual and your vehicle owner’s manual
before installing and using this child restraint. Using a
child restraint makes a big difference. By properly using
this child restraint and following these instructions (and
the instructions that accompany your vehicle), you will
greatly reduce the risk of serious injury or death to your
child from a crash. Do not be misled by the commonly
used term “safety seat”; no restraint system can prevent all injuries in all crashes. Many properly restrained
adults and children are injured in motor vehicle crashes,
including relatively minor crashes. A properly used child
restraint is the best way to minimize injuries to your child
and to increase the chances for your child’s survival in
most crashes.
1
WARNING
Air Bag Warnings
General Warnings
Rear-facing and Forward-facing Use
Rear-facing and Forward-facing Use
• DO NOT use this child restraint in the front seat of a
vehicle equipped with an air bag. Interaction between
a rear-facing restraint and air bags may cause serious
injury or death. Air bags may cause serious injury or
death to children 12 and under.
If your vehicle has an air bag, refer to your vehicle
owner’s manual for child restraint installation.
• If the rear seat of your vehicle is equipped with side
air bags, refer to the following information for proper
usage.
Vehicles built prior to the 2002 model year:
DO NOT use this restraint in a vehicle seating position
equipped with a side air bag unless authorized by the
vehicle manufacturer.
Model year 2002 and newer vehicles:
Refer to your vehicle owner’s manual before placing this
restraint in a seating position equipped with a side air bag.
• DO NOT place any objects between the restraint and
the side air bag, as an expanding air bag may cause
the items to strike the child.
• Failure to follow installation instructions can result in
the child striking the vehicle’s interior during a sudden
stop or crash. Serious injury or death may result.
These instructions and the instructions in your vehicle
owner’s manual must be followed carefully. If there
is a conflict between the two, the vehicle owner’s
manual regarding child restraint installation must
be followed.
• NEVER leave child unattended.
• DO NOT use child restraint if it is damaged, broken,
or missing parts.
• DO NOT use this restraint if it has been involved in a
crash. It must be replaced.
• DO NOT remove back cover.
NO coloque el asiento infantil orientado
hacia atrás en el asiento delantero con
bolsa de aire.
Puede causar MUERTE o LESIONES
GRAVES. El asiento trasero es el lugar más
seguro para los niños de 12 años de edad y
2
Important Information
WARNING
Location Warnings
Rear-facing and Forward-facing Use
• ALWAYS read and follow exactly the instructions that
accompany your vehicle and child restraint.
• According to statistics, children are safer when properly
restrained in a rear seating position than in the front
seating position. Generally, the center rear position is
safest and should be used if available.
• Some child restraints do not fit all vehicles or all seating
locations. There are many thousands of combinations of
vehicle makes, models, child restraint configurations,
vehicle seat belt designs, and seat cushion shapes. The
easiest way to determine whether your child restraint is
suitable for a particular seating position is to check
for a tight installation. If the child restraint can not be
properly installed, DO NOT use the child
restraint. Consult vehicle owner’s manual, try a different
seating location or call Evenflo at 1-800-233-5921.
• ONLY use this child restraint on forward-facing
vehicle seats. DO NOT use this restraint with vehicle
seats that face the rear or side.
• ONLY use this child restraint on vehicle seats with
backs that lock into place.
3
WARNING
Premature Infants
Forward-facing Position Warnings
Rear-facing and Forward-facing Use
Forward-facing Use Only
• DO NOT use this or any child restraint with a
premature infant until after consulting your doctor.
Also, some infants may have difficulty breathing when
in a seated or semi-reclined position. Using additional
padding or pillows behind the infant’s head, or failure
to properly recline the child restraint may increase the
child’s risk of serious injury or death.
• When using the harness straps to secure a child who
is more than 40 lbs (18 kg), NEVER place the child
restraint in Recline Position #2. Use ONLY Recline
Position #3.
• Install this child restraint with a vehicle seat belt ONLY
(NOT Latch™ connectors) when using the restraint’s
harness straps to secure a child who weighs more
than 48 lbs (21.7 kg).
• If the child weighs more than 65 lbs (29.4 kg) OR
their shoulders are above the highest harness level,
you can not use this child restraint. You MUST use a
booster seat.
• Adjust, or remove, the vehicle headrest, in the seat
where the child restraint is to be installed, so that
the back of the child restraint rests against the vehicle
seat back.
• The headrest on the vehicle seat in front of the child
should be put in its lowest position. The vehicle seat
back that the child faces must be fully padded and
free of any hard objects.
Rear-facing Position Warnings
Rear-facing Use Only
• DO NOT use this child restraint rear-facing in a vehicle
equipped with lap belts that only lock during a sudden
stop or crash (emergency locking retractor – ELR). You
must use a seating location with a locking seat belt.
Check your vehicle owner’s manual to see if you have
lap belts with ELR’s.
• When using this restraint rear-facing, DO NOT loosen
the vehicle seat belt to provide more leg room as this will
prevent the child restraint from protecting the child.
• Fold-down armrests could pose a hazard to a rearfacing child in certain types of collisions. Consult your
vehicle owner’s manual before installing any rearfacing child restraint in front of a fold-down armrest.
• NEVER turn a child restraint forward-facing with an infant
weighing less than 20 lbs (9 kg) or less than one year of
age. Crash forces may cause serious injury or death.
• NEVER use Recline Position #2 or Recline Position #3
when using this child restraint rear-facing. Use ONLY
Recline Position #1.
• DO NOT use the tether strap when the child restraint
is in the rear-facing position.
• The headrest on the vehicle seat that the child faces
when sitting in the rear facing mode should be placed
in the lowest position. The vehicle seat back that the
child faces must be fully padded and free of any hard
objects.
4
Important Information
WARNING
Seat Belt Warnings
Rear-facing and Forward-facing Use
• DO NOT use this child restraint if it moves more than
1 inch (25 mm) forward or side-to-side at either
rear-facing or forward-facing belt path on the child
restraint. Serious injury or death may result from poor
installation. If you can not tightly secure the child
restraint, try again or move it to another location.
• DO NOT use this child restraint in a seating position
with door-mounted seat belts.
• DO NOT use this child restraint in a vehicle with seat
belts that automatically move along the vehicle frame
when the door is opened. These seat belts will not
hold a child restraint properly.
• If the vehicle seat belts are not routed and fastened
correctly, the child restraint may not protect the child
in a crash.
5
Seat Belt Warnings – cont.
Rear-facing and Forward-facing Use
• DO NOT allow the vehicle seat belt release button to
touch the child restraint. Accidental contact may cause
the seat belt to release. If necessary, turn the seat belt
release button away from the child restraint or move
the child restraint to a different location.
• Failure to adjust the harness or vehicle seat belts
snugly around the child may result in the child striking
the vehicle’s interior during a sudden stop or crash.
Serious injury or death may occur.
• Remove locking clip from vehicle seat belt
when not used with a child restraint, or the
Locking Clip
vehicle seat belt will not properly restrain
an adult or child. Serious injury or death may occur.
LATCH Warnings
Rear-facing and Forward-facing Use
• This LATCH system is intended to be used ONLY as
described in these instructions. Serious injury or death
may result from misuse.
• In addition to these instructions, read and follow your
vehicle owner’s manual regarding installation of the
child restraint and LATCH. If there is a discrepancy,
follow your vehicle owner’s manual.
• ONLY use for securing child restraint to lower LATCH
anchor points.
• NEVER attach two LATCH connectors to one vehicle lower
anchor point.
• NEVER use the vehicle seat belts when using the
LATCH system. Using both together can cause slack in
a sudden stop or crash.
• When not in use, the LATCH connectors should be
securely attached to the D-rings on child restraint seat
pad. Keep out of reach of children.
ALWAYS be sure that the LATCH connectors are fully
engaged onto the LATCH anchor points by pulling
hard on the LATCH straps. If they are not fully engaged, the LATCH system will not secure your child
restraint. Serious injury or death may result.
6
WARNING
• DO NOT use this child restraint if it moves more than
1 inch (25 mm) forward or side-to-side at either the
rear-facing or forward-facing belt path on the child
restraint. Serious injury or death may result from poor
installation. If you can not tightly secure the child
restraint, try again or move it to another location.
Tether Strap Warnings
Forward-facing Use Only
Important Information
WARNING
• To avoid a strangulation hazard, you MUST tightly roll
or fold excess or unused tether strap and secure with
a rubber band. Attach the tether hook to the storage
clip when not in use (p. 13). This will keep an unused
tether from hitting someone during a crash.
Additional Warnings
Rear-facing and Forward-facing Use
• In hot or sunny weather, ALWAYS check the seat, the
buckle and LATCH hooks, and adjuster for hot areas
before placing a child into the child restraint. The child
could be burned. Cover the child restraint with a light
colored blanket when you leave the vehicle.
• This child restraint must be securely fastened to the
vehicle, even when unoccupied, using the vehicle
seat belts or LATCH connectors. An unsecured child
restraint may injure someone if a crash occurs.
• DO NOT use the cup holder to store cans or hard
cups. Only for use with soft cups (such as styrofoam
or paper).
• DO NOT place any cups that contain hot liquids
(such as coffee or tea) in the cup holder.
• DO NOT attach additional padding, toys or other
devices not made by Evenflo or described in these
instructions to the child restraint. Items not tested with
the child restraint could injure the child. Additional
pads or pillows may interfere with the function of the
harness system, or cause breathing problems if the child’s
head falls forward, increasing the risk of serious injury
or death.
7
Additional Warnings – cont.
Rear-facing and Forward-facing Use
• Failure to follow installation instructions could result
in serious injury or death. These instructions and the
instructions in your vehicle owner’s manual must be
followed carefully. If there is a conflict between the
two, the vehicle owner’s manual regarding child
restraint installation must be followed.
• In cold weather, DO NOT dress the child in bulky
clothing like snowsuits if the child is riding in a child
restraint. Bulky coats/snowsuits make it difficult to
properly tighten the harness to the child which may
allow the child to be ejected from the restraint during
a crash. If necessary, place a blanket over the
harnessed child without interfering with the child
restraint harness system.
8
Safe Practices
• Everyone rides buckled up or the vehicle does
not go. Make no exceptions for adults or children.
If someone unbuckles, stop the vehicle. Being firm
and consistent from the start will mean fewer
discipline problems as children get older.
An unrestrained person can be thrown into and injure
other passengers.
• Many safety advocates and healthcare
professionals recommend that children ride
rear facing for as long as possible. See limitations
recommended on rear-facing use on the inside
front cover.
• NEVER try to tend to a crying baby’s needs while
driving. NEVER take a baby out of a child restraint for
comforting while the vehicle is moving.
• DO NOT allow a child in a vehicle to have objects
such as lollipops or ice cream on a stick. The object
can injure the child if the vehicle swerves or hits a
bump.
• DO NOT feed an infant who is riding in a child
restraint.
• Put sharp or heavy items in the trunk. Anything loose
can be deadly in a crash.
Important Information
WARNING
9
Symbol Legend
• Child restraints could be recalled for safety reasons.
You must register this restraint to be reached in a
recall. Send your name, address, the restraint’s
model number, and manufacturing date to
Evenflo Company, Inc.,
1801 Commerce Dr.,
Piqua, OH 45356
or call 1-800-233-5921.
You may also register on-line at
https://plweb.evenflo.com/productreg.aspx
• For recall information call the U.S. Government’s
Vehicle Safety Hotline at 1-888-327-4236
(TTY:1-800-424-9153), or go to
http://www.NHTSA.gov
Air Bag Symbol – Alerts you to important
information about air bag safety.
LATCH Symbol – Alerts you to important
information about LATCH safety.
Tether Anchor Symbol – Alerts you to
important information about tether anchor safety.
Important Information
Recall Information
Airplane Usage
This restraint is certified for use
in motor vehicles and aircraft.
Tip!
Check with
your airline before
departure to make sure
this restraint meets
their requirements.
Para instrucciones en Español, llamar al: 1-800-233-5921
LATCH Information
OWNER’S MANUAL
Keep for future use.
™
Momentum
Child Restraint System
WARNING
“LATCH” (Lower Anchors and Tethers for CHildren) is a
system for attaching the child restraint to your vehicle
seat. It can be used in place of the seat belts in vehicles
with LATCH anchors. Refer to your vehicle owner’s
manual for the locations of LATCH anchors. Note: Your
vehicle owner’s manual may refer to this system as
”ISOFIX.”
To reduce the risk
of SERIOUS INJURY or
DEATH, read this owner’s
manual prior to installing
and using this child
restraint.
© Evenflo Company, Inc. 2008
2570xxxx 7/08
Para instrucciones en Español, llamar al: 1-800-233-5921
OWNER’S MANUAL
Keep for future use.
For future reference, record the model number of your child
restraint AND the date of manufacture below.
Model Number:
Date of Manufacture:
10
™
Momentum
Child Restraint System
WARNING
To reduce the risk
of SERIOUS INJURY or
DEATH, read this owner’s
manual prior to installing
and using this child
restraint.
© Evenflo Company, Inc. 2008
2570xxxx 7/08
11
Visual Glossary
Your vehicle components may be significantly different than pictured.
Consult your owner’s manual to help you identify your vehicle components.
Rear
Headrests
Tether Anchors
Forward-facing
ONLY
Front Seat Lap
and Shoulder Belts
Fold-down Armrest
Consult your vehicle’s
owners manual.
Front
Headrests
10
Back Seat
Belt Buckles
120
NO coloque el asiento infantil orientado
hacia atrás en el asiento delantero con
bolsa de aire.
Puede causar MUERTE o LESIONES
GRAVES. El asiento trasero es el lugar más
seguro para los niños de 12 años de edad y
A
IR
B
A
G
Center Lap
Belt
Back Seat
Belt Retractor
4
30
20
Lap/Shoulder
Belt
Important Information
Visual Glossary
Important
Consult your vehicle
owner’s manual to determine
proper placement of child restraint
in your vehicle and familiarize
yourself with your vehicle’s
components.
LATCH
Anchors
Seat Crease
Front Seat
Retractor
IMPORTANT: If your vehicle has side air bags, please refer to the
warnings on page 2.
Back
Front
Tether Strap
and Hook
Chest Clip
Harness Tabs
(Shown fastened to
storage clip)
Instructions
Para instrucciones en Español, llamar al: 1-800-233-5921
Buckle
EZ Off Seat Pad
OWNER’S MANUAL
Keep for future use.
Harness
Release Button
Harness Straps
Harness
Adjust Strap
D-rings for
SureLatch™ Connector
SureLatch™ Connector
(Shown in Rear-facing
belt path)
™
Momentum
Child Restraint System
Forward-facing
Belt Path
WARNING
To reduce the risk
of SERIOUS INJURY or
DEATH, read this owner’s
manual prior to installing
and using this child
restraint.
© Evenflo Company, Inc. 2008
SureLatch™ Connector
Forward-facing
Belt Path
SureLatch™ Connector
(Shown in Rear-facing
belt path)
(Shown in Rear-facing
belt path)
Base
Base
2570xxxx 7/08
Locking Clip
Recline Lever
Quick Connector™
12
(Shown in Rear-facing
belt path)
13
Securing the Child in the Child Restraint
1. Loosen Harness.
Press the harness release
4.Buckle the harness.
Insert both buckle
button on the front of the
seat, then pull up on the
harness strap behind the
fastened chest clip.
tongues into the buckle.
Note: Pull up on the
harness straps to ensure
that the buckle tongues
are fastened securely.
Important Information
Securing the Child in the Child Restraint
2.Position harness
straps.
Unfasten chest clip and
place the child in the
child restraint.
Bring each harness strap
over the child’s shoulders.
IMPORTANT: The baby’s back and bottom should be flat
against the restraint. If there is a gap, the baby will not be
comfortable.
3.Adjust harness straps.
Grasping both red harness
tabs, slide downward until
the harness straps are at,
or slightly below, the child’s
shoulders.
5.Tighten harness.
Pull the harness adjuster strap to tighten the harness.
Note: Make sure the harness straps are snug against
the child with no more than two finger-widths
between the child and straps.
IMPORTANT: A snug strap should not allow any slack.
It lies in a relatively straight line without sagging. It does
not press on the child’s flesh or push the child’s body into
an unnatural position.
Check the harness straps near the shoulders for slack and
adjust as needed.
6.Fasten and adjust
chest clip.
Snap the two halves of
the chest clip together,
as shown, and slide to
armpit level.
14
15
1. Loosen harness
straps.
Press the harness release
button on the front of the
seat while pulling up on
the harness strap behind
the fastened chest clip.
This page is intentionally blank.
Important Information
Removing the Child from the Restraint
2.Disconnect chest clip.
Push the release button
and pull the chest clip
apart.
3.Unbuckle harness.
Press the red button on
the buckle and release
both buckle tongues.
16
You may now remove
your child.
17
Child Requirements
Weight: 5 – 40 lbs (2.3 – 18 kg)
Height: Top of child’s head is at least 1 inch (25 mm)
below the top of the child restraint.
1 inch (25 mm)
or more
Harness straps are
at, or slightly below,
child’s shoulders.
Rear-facing Installation Checklist
1.Secure child restraint to the vehicle seat.
aRestraint is securely locked into Recline Position #1
(p. 52).
aLocking clip is installed, if necessary (p. 53).
aThe level line is level with ground (p. 23, 27, or 30).
A towel/small blanket is rolled up and placed
beneath the front edge of the base, if necessary
(p. 23, 27, or 30).
aInstalled with LATCH System
(To determine which LATCH connectors are on your
child restraint, go to page 20.)
• Child restraint is securely installed with SureLatch™
Connectors (shown) through rear-facing belt
path (p. 20)
OR
• Child restraint is securely installed with Quick
Connectors™ through rear-facing belt path (p. 24)
aInstalled with vehicle seat belt
Child restraint is securely installed with vehicle
seat belt through rear-facing belt path (p. 28.)
Rear-facing Checklist
Using Momentum™ in
the Rear-facing Position
2.Place the child in the child restraint.
aThe child’s back and bottom are flat against the
back and bottom surfaces of the child restraint.
aTop of child’s head is at least 1 inch (25 mm)
below the top of the child restraint.
3.Make necessary adjustments.
aRed harness tabs MUST be at, or slightly below,
shoulder level (p. 14).
aHarness is no more than two-finger widths
from child (p. 15).
4.Fasten both buckle tongues. Refer to page 15.
5.Position and connect chest clip.
aChest clip MUST be placed at armpit level (p. 15).
6.Check your work.
aTo properly secure this child restraint, it MUST
NOT move more than 1 inch (25 mm) from
side-to-side or from front-to-back at the
rear-facing belt path.
18
Tip!
To make installation easier, watch the installation
video of this child restraint at www.evenflo.com.
19
In order to properly install your child restraint with the
LATCH system, you must first know which type of LATCH
connectors are present on your child restraint.
• If your child restraint has SureLatch™ Connectors,
begin installation by referring to “Moving SureLatch™
Connectors to the Rear-facing Belt Path,” below.
Moving SureLatch™ Connectors to the
Rear-facing Belt Path
1.Remove SureLatch™
connectors from
the forward-facing
belt path.
Reach through the
harness straps and
remove each SureLatch™
connector, one at a time.
• If your child restraint has the Quick Connectors™, begin
installation by referring to page 24, “Moving Quick
Connectors™ to the Rear-facing Belt Path.”
SureLatch™ Connector
Quick Connector™
Moving SureLatch™ Connectors to the
Rear-facing Belt Path
To install this child restraint properly in rear-facing position,
the SureLatch™ connectors must be in the rear-facing belt
path, as shown below (seat pad has been removed for clarity).
If the SureLatch™ connectors are in the forward-facing belt
path (shown below), use the following procedures to move
them to the rear-facing belt path.
To access the SureLatch™ connectors, you will first need to:
• Loosen internal harness straps (p. 16);
• Disconnect SureLatch™ connectors (p. 50);
• Remove seat pad (p. 52).
2.Place each
connector in the
rear-facing belt
path.
Install with SureLatch™
Which Type of LATCH Connector is on
Your Momentum Child Restraint?
3.Make sure the
buckle and crotch
strap is positioned
through the LATCH
harness straps,
as shown.
SureLatch™ Connectors in SureLatch™ Connectors in
Rear-facing Belt Path
Forward-facing Belt Path
CIN
R FA
REA
G
FO RW
20
AR D
FA CIN
G
Note: Don’t forget to install the seat pad before installing
the child restraint in your vehicle.
21
Rear-facing Installation with
SureLatch™ Connectors
Rear-facing Installation with
SureLatch™ Connectors
Recline
Positions
to the most reclined
position (Recline Position
#1, p. 52) then place it on
vehicle seat in the rearfacing position, as shown.
Near Side
UP
E
SID
IS
TH
1.Place the child
restraint in position.
Adjust the child restraint
1 Used for
Rear-facing ONLY.
2
3
Level
Line
&
Used for
Forward-facing ONLY.
Arrow must be level with ground
when used rear-facing.
Tightly rolled towel
or small blanket
If level line is not parallel
to the ground, disconnect
SureLatch™ connectors
and place a tightly rolled
towel/small blanket
beneath the front edge
of the child restraint.
Repeat Step 2.
IMPORTANT: Infants may have difficulty breathing when
in a sitting position. Make sure they recline enough for their
head to lie back comfortably and safely. Failure to properly
recline the child restraint could increase the child’s risk
of serious injury or death.
Far side
4.Secure the child
restraint.
Push downward on the
Install with SureLatch™
3.Increase recline
angle, if necessary.
IMPORTANT:
•If you are using the vehicle seat belt to secure the child
restraint, DO NOT use the LATCH system.
•DO NOT use the tether strap when the child restraint is
in the rear-facing position.
child restraint, as shown,
to set it in place.
LATCH Anchor
LATCH Anchor
2.Attach SureLatch™ Connectors.
Push a SureLatch™ connector onto each seat anchor.
Note: You may need to vary the angle of the SureLatch™
connectors, as shown above, to attach to the anchor.
Also, make sure LATCH strap is in the rear-facing
belt path (p. 20).
Strap
Rear-facing Belt Path
IMPORTANT: To properly secure this child restraint, it
MUST NOT move more than 1 in. (25 mm) from side-toside or from front-to-back at the rear-facing belt path.
If you can not tightly secure the child restraint, try again,
move it to another location, or install with vehicle seat belt.
IMPORTANT: Make sure both
SureLatch™ connectors are
facing upward and the straps
are not twisted.
22
Note: In some vehicles, you may
need to prop up the connector
while pushing downward on the
seat to secure it tightly. Repeat
for the other connector.
23
To install this child restraint properly in rear-facing
position, the Quick Connectors™ MUST be in the
rear-facing belt path, as shown below (seat pad has been
removed for clarity). If the Quick Connectors™ are in the
forward-facing belt path (shown below), use the following
procedures to move them to the rear-facing belt path.
To access the Quick Connectors™, you will first need to:
• Loosen internal harness straps (p. 16);
• Disconnect Quick Connectors™ (p. 51);
• Remove seat pad (p. 52).
Quick Connectors™ in
Rear-facing Belt Path
Quick Connectors™ in
Forward-facing Belt Path
Moving Quick Connectors™ to the
Rear-facing Belt Path
2.Place each connector
in the rear-facing
belt path.
3.Make sure the
LATCH strap is
positioned in front
of the buckle and
crotch strap,
as shown.
Install with Quick Connectors™
Moving Quick Connectors™ to the
Rear-facing Belt Path
Note: Don’t forget to install the seat pad before installing
the child restraint in your vehicle.
1.Remove Quick
Connectors™ from
the forward-facing
belt path.
Reach through the
harness straps and
remove each Quick
Connector, one at a time.
24
25
Rear-facing Installation with
Quick Connectors™
Rear-facing Installation with
Quick Connectors™
Recline
Positions
1.Place the child
restraint in position.
Adjust the child restraint
to the most reclined
position (Recline Position
#1, p. 52) then place it on
vehicle seat in the rearfacing position, as shown.
Near Side
2
3
Level
Line
&
Used for
Forward-facing ONLY.
Arrow must be level with ground
when used rear-facing.
Tightly rolled towel
or small blanket
IMPORTANT: Infants may have difficulty breathing when
in a sitting position. Make sure they recline enough for their
head to lie back comfortably and safely. Failure to properly
recline the child restraint could increase the child’s risk
of serious injury or death.
Far side
LATCH Anchor
LATCH Anchor
2.Attach Quick Connectors.
1 Used for
Rear-facing ONLY.
Push a Quick Connector onto each seat anchor.
Note: You may need to vary the angle of the Quick
Connectors, as shown above, to attach to the anchor.
Also, make sure LATCH strap is in the rear-facing
belt path (p. 24).
If level line is not parallel
to the ground, disconnect
Quick Connectors
and place a tightly rolled
towel/small blanket
beneath the front edge
of the child restraint.
Repeat Step 2.
4.Secure the child
restraint.
Using your full weight,
Install with Quick Connectors™
3.Increase recline
angle, if necessary.
IMPORTANT:
•If you are using the vehicle seat belt to secure the child
restraint, DO NOT use the LATCH system.
•DO NOT use the tether strap when the child restraint is
in the rear-facing position.
push the child restraint
firmly into the vehicle seat
while pulling up on the
LATCH strap to tighten.
Rear-facing Belt Path
IMPORTANT: To properly secure this child restraint, it
MUST NOT move more than 1 in. (25 mm) from side-toside or from front-to-back at the rear-facing belt path.
If you can not tightly secure the child restraint, try again,
move it to another location, or install with vehicle seat belt.
IMPORTANT: Make sure both LATCH Quick Connectors are
facing upward and the straps are not twisted.
Correct
26
Incorrect
27
Rear-facing Installation with
Vehicle Seat Belt
Rear-facing Installation with
Vehicle Seat Belt
IMPORTANT:
•If you are using SureLatch™ or Quick Connectors™ to
secure the child restraint, DO NOT use a vehicle seat belt.
•NEVER use the tether strap when the child restraint is in
the rear-facing position.
4.Remove all slack
from the seat belt.
Push downward on
1.Place the child
restraint in position.
Adjust the child restraint
to the most reclined
position (Recline Position
#1, p. 52) then place it on
vehicle seat in the rearfacing position, as shown.
5.Install locking clip,
if necessary.
2.Route seat belt
through rear-facing
belt path.
Unhook the front of the
seat pad and move it out
of the way.
Thread the vehicle seat
belt buckle tongue
through the rear-facing
belt path, as shown.
IMPORTANT: Make sure the vehicle seat belt is in front of
the crotch strap.
3.Buckle seat belt.
28
Locking Clip
installed properly
You MUST use a locking
clip if your vehicle has:
a) Lap/shoulder seat
belts with a buckle
tongue that slides freely
along the belt without
locking into place; or
b) Seat belts equipped
with an emergency
locking retractor (ELR).
Install with Vehicle Seat Belt
child restraint while
tightening the vehicle
seat belt to remove
excess slack.
Consult your vehicle owner’s manual before
installing the locking clip.
To see an example of seat belt types and to properly
install a locking clip, go to p. 53.
6.Connect seat pad
to the front of the
child restraint.
29
Rear-facing Installation with
Vehicle Seat Belt
This page is intentionally blank.
Recline
Positions
1 Used for
Rear-facing ONLY.
2
3
&
Used for
Forward-facing ONLY.
Arrow must be level with ground
when used rear-facing.
Recline
Positions
1 Used for
Rear-facing ONLY.
2
3
Level
Line
&
Used for
Forward-facing ONLY.
Arrow must be level with ground
when used rear-facing.
Tightly rolled towel
or small blanket
parallel to the ground,
disconnect the seat belt
and place a tightly rolled
towel/small blanket
beneath the front edge
of the child restraint.
Repeat Step 2.
IMPORTANT: Infants may have difficulty breathing when
in a sitting position. Make sure they recline enough for their
head to lie back comfortably and safely. Failure to properly
recline the child restraint could increase the child’s risk of
serious injury or death.
8.Ensure child
restraint is secure.
Try to move the child
Install with Vehicle Seat Belt
7.Increase recline
angle, if necessary.
If the level line is not
restraint in all directions.
Rear-facing
Belt Path
30
IMPORTANT: To properly
secure this child restraint, it
MUST NOT move more than
1 in. (25 mm) from side-toside or from front-to-back at
the rear-facing belt path.
If you can not tightly secure
the child restraint, try again,
move it to another location,
or install with the LATCH
system.
31
Using Momentum™ in the
Forward-facing Position
1.Secure child restraint to the vehicle seat.
aRestraint is securely locked into Recline Position #2
Child Requirements
or #3 (p. 52).
Weight: 20 – 65 lbs (9 – 29.4 kg)
Height: 50 inches (127 cm) tall,
or less AND the top of the
child’s ears are at, or below,
the top of the child restraint.
Age:
At least one year old
aLocking clip is installed, if necessary (p. 53).
aIf the child weighs 48 lbs (21.7 kg) or less, the
child restraint is securely installed with LATCH system.
(To determine which LATCH connectors are on your
child restraint, go to page 34.)
• Child restraint is securely installed with SureLatch™
IMPORTANT
Evenflo strongly recommends using the top
anchorage (tether) strap when securing a child in this
child restraint with the harness straps. Using the tether
strap will improve the stability of this child restraint
and may reduce the risk of injury.
Tether Strap
Forward-facing Installation Checklist
Harness straps are
at child’s shoulders.
Connectors (shown) through forward-facing belt
path (p. 34)
OR
• Child restraint is securely installed with Quick
Connectors™ through rear-facing belt path (p. 40)
aIf the child weighs more than 48 lbs (21.7 kg),
the child restraint is securely installed with the
vehicle seat belt through forward-facing belt path
(p. 45).
aTether strap is attached and tightened (p. 39, 44,
or 48).
2.Place the child in the child restraint.
back and bottom surfaces of the child restraint.
Forward-facing Checklist
aThe child’s back and bottom are flat against the
aThe top of the child’s ears MUST be below the
top of the child restraint.
3.Make necessary adjustments.
aRed harness tabs MUST be at shoulder level.
aHarness is no more than two-finger widths
from child (p. 15).
4.Fasten both buckle tongues. Refer to page 15.
5.Position and connect chest clip.
aChest clip MUST be at armpit level (p. 15).
6.Check your work.
aTo properly secure this child restraint, it MUST
WARNING
If the child weighs more than 65 lbs (29.4 kg) or
their shoulders are above the highest harness level,
you MUST use a Booster Seat.
32
NOT move more than 1 inch (25 mm) from
side-to-side or from front-to-back at the
forward- facing belt path.
Tip!
To make installation easier, watch the installation
video of this child restraint at www.evenflo.com.
33
Which Type of LATCH Connectors are
on Your Child Restraint?
Moving SureLatch™ Connectors to the
Forward-facing Belt Path
In order to properly install your child restraint with the
LATCH system, you must first know which type of LATCH
connectors are present on your child restraint.
• If your child restraint has SureLatch™ Connectors,
begin installation by referring to “Moving SureLatch™
Connectors to the Forward-facing Belt Path,” below.
1.Remove one SureLatch™
connector from the
rear-facing belt path.
• If your child restraint has the Quick Connectors™,
begin installation by referring to page 40, “Moving
Quick Connectors™ to the Forward-facing Belt Path.”
SureLatch™ Connector
Quick Connector™
2.Place the connector
in the forwardfacing belt path.
To install this child restraint properly in forward-facing
position, the SureLatch™ connectors must be in the
forward-facing belt path, as shown below (seat pad has
been removed for clarity). If the SureLatch™ connectors are
in the rear-facing belt path (shown below), use the following
procedures to move them to the forward-facing belt path.
To access the SureLatch™ connectors, you will first need to:
• Loosen internal harness straps (p. 16);
• Disconnect SureLatch™ connectors (p. 50);
• Remove seat pad (p. 52).
Pull the harness strap out
of the way and insert the
connector, behind the
straps, into the forwardfacing belt path opening,
as shown.
Repeat on the other side.
3.Make sure the
LATCH strap
does not interfere
with the internal
harness straps.
SureLatch™ Connectors in SureLatch™ Connectors in
Forward-facing Belt Path
Rear-facing Belt Path
FO RW
AR D
FA CI
NG
Install with SureLatch™
Moving SureLatch™ Connectors to the
Forward-facing Belt Path
Note: Don’t forget to install the seat pad before installing
the child restraint in your vehicle.
34
35
Forward-facing Installation with
SureLatch™ Connectors
IMPORTANT:
•If you are using the vehicle seat belt to secure the child
restraint, DO NOT use SureLatch™ connectors.
•Install this child restraint with the vehicle seat belt
(NOT LATCH connectors) if the child weighs more than
48 lbs (21.7 kg).
Note: Some vehicle manufacturers have lower maximum
weight ratings for LATCH anchors. Consult your vehicle
owner’s manual, or call the vehicle manufacturer, to
confirm the limits on your vehicle’s LATCH anchors.
1.Disconnect tether
hook from the back
of the child restraint.
Forward-facing Installation with
SureLatch™ Connectors
Near Side
LATCH Anchor
Far side
LATCH Anchor
3.Attach SureLatch™ Connectors.
Push a SureLatch™ connector onto each seat anchor.
Note: You may need to vary the angle of the SureLatch™
connectors, as shown above, to attach to the anchor.
Also, make sure LATCH strap is in the forward-facing belt
path (p. 34).
Tether
Strap
2.Place the child
restraint in position.
Make sure child restraint
is in Recline Position #2
or #3 (p. 52).
Set child restraint on
vehicle seat in forwardfacing position, as
shown. Lay the tether
strap over the back of
the vehicle seat.
IMPORTANT: Make sure both
SureLatch™ connectors are
facing upward and the straps
are not twisted.
Install with SureLatch™
Strap
IMPORTANT: NEVER use Recline Position #1 for forwardfacing, AND NEVER use Recline Position #2 with children
who weigh more than 40 lbs (18 kg).
36
37
Forward-facing Installation with
SureLatch™ Connectors
Forward-facing Installation with
SureLatch™ Connectors
4.Secure the child
restraint.
Push downward on the
child restraint, as shown,
to set it in place.
5.Connect and tighten
tether strap.
IMPORTANT: To properly secure this child restraint, it
MUST NOT move more than 1 inch (25 mm) from sideto-side or from front-to-back at the forward-facing
belt path. If you can not tightly secure the child restraint,
try again, move it to another location, or install with vehicle
seat belt.
Note: In some vehicles, you
may need to prop up the
connector while pushing
downward on the seat to
secure it tightly. Repeat for
the other connector.
38
IMPORTANT: If your tether strap is too short to reach
from your child restraint to your vehicle tether anchor,
you will need a Tether Extender. Please call ParentLink at
1-800-233-5921.
Install with SureLatch™
Forward-facing
Belt Path
Connect the tether hook
to the anchor behind the
vehicle seat, as shown.
Pull the strap and tighten
the tether securely.
39
To install this child restraint properly in forward-facing
position, the Quick Connectors™ MUST be in the
forward-facing belt path, as shown below (seat pad has
been removed for clarity). If the Quick Connectors™ are in
the rear-facing belt path (shown below), use the following
procedures to move them to the forward-facing belt path.
To access the Quick Connectors™, you will first need to:
• Loosen internal harness straps (p. 16);
• Disconnect Quick Connectors (p. 51);
• Remove seat pad (p. 52).
Quick Connectors™ in
Forward-facing Belt Path
Quick Connectors™ in
Rear-facing Belt Path
1.Remove one Quick
Connector™ from the
rear-facing belt path.
40
Moving Quick Connectors™ to the
Forward-facing Belt Path
2.Place the connector
in the forwardfacing belt path.
Pull the harness strap out
of the way and insert the
connector, behind the
straps, into the forwardfacing belt path opening,
as shown.
Repeat on the other side.
3.Make sure the
LATCH strap
does not interfere
with the internal
harness straps.
Note: Don’t forget to install the seat pad before installing
the child restraint in your vehicle.
Install with Quick Connectors™
Moving Quick Connectors™ to the
Forward-facing Belt Path
41
Forward-facing Installation with
Quick Connnectors™
1.Disconnect tether
hook from the back
of the child restraint.
Near Side
Far side
LATCH Anchor
LATCH Anchor
3.Attach Quick Connectors.
Push a Quick Connector onto each seat anchor.
Note: You may need to vary the angle of the Quick
Connectors, as shown above, to attach to the anchor.
Also, make sure LATCH strap is in the forward-facing belt
path (p. 24).
IMPORTANT: Make sure both LATCH Quick Connectors are
facing upward and the straps are not twisted.
Correct
Tether
Strap
2.Place the child
restraint in position.
Make sure child restraint
is in Recline Position #2
or #3 (p. 52).
Set child restraint on
vehicle seat in forwardfacing position, as
shown. Lay the tether
strap over the back of
the vehicle seat.
Incorrect
Install with Quick Connectors™
IMPORTANT:
•If you are using the vehicle seat belt to secure the child
restraint, DO NOT use the Quick Connectors™.
•Install this child restraint with the vehicle seat belt
(NOT LATCH connectors) if the child weighs more than
48 lbs (21.7 kg).
Note: Some vehicle manufacturers have lower maximum
weight ratings for LATCH anchors. Consult your vehicle
owner’s manual, or call the vehicle manufacturer, to
confirm the limits on your vehicle’s LATCH anchors.
Forward-facing Installation with
Quick Connnectors™
IMPORTANT: NEVER use Recline Position #1 for forwardfacing, AND NEVER use Recline Position #2 with children
who weigh more than 40 lbs (18 kg).
42
43
Forward-facing Installation with
Vehicle Seat Belt
Forward-facing Installation with
Quick Connnectors™
push the child restraint
firmly into the vehicle seat
while pulling up on the
LATCH strap to tighten.
Forward-facing
Belt Path
IMPORTANT:
•Before installing this child restraint forward-facing with
the vehicle seat belt, you MUST move the LATCH strap
to the rear-facing belt path so that is does not interfere
with the vehicle seat belt.
•If your child restraint has SureLath connectors, refer to
page 34. If your child restraint has Quick Connectors™,
refer to page 40.
Also, make sure the SureLatch™ or Quick Connectors™ are
attached to the storage D-rings on the seat pad.
1.Disconnect tether
hook from the back
of the child restraint.
IMPORTANT: To properly secure this child restraint, it
MUST NOT move more than 1 inch (25 mm) from sideto-side or from front-to-back at the forward-facing
belt path. If you can not tightly secure the child restraint,
try again, move it to another location, or install with vehicle
seat belt.
Tether
Strap
5.Connect and tighten
tether strap.
Connect the tether hook
to the anchor behind the
vehicle seat, as shown.
Pull the strap and tighten
the tether securely.
IMPORTANT: If your tether strap is too short to reach
from your child restraint to your vehicle tether anchor,
you will need a Tether Extender. Please call ParentLink at
1-800-233-5921.
44
2.Place the child
restraint in position.
Make sure child restraint
is in Recline Position #2
or #3 (p. 52).
Set child restraint on
vehicle seat in forwardfacing position, as
shown. Lay the tether
strap over the back of
the vehicle seat.
Install with Vehicle Seat Belt
4.Secure the child
restraint.
Using your full weight,
IMPORTANT: NEVER use Recline Position #1 for forwardfacing, AND NEVER use Recline Position #2 with children
who weigh more than 40 lbs (18 kg).
45
Forward-facing Installation with
Vehicle Seat Belt
Forward-facing Installation with
Vehicle Seat Belt
5.Remove all slack
from the seat belt.
Using your full weight,
Access Flap
push the child restraint
firmly into the vehicle
seat while tightening
seat belt to remove
excess slack.
Move the harness out of the way and raise the
access flap. Route the seat belt buckle tongue through
the forward-facing belt path, as shown.
4.Buckle seat belt.
Locking Clip
installed properly.
You MUST use a locking
clip if your vehicle has:
a) Lap/shoulder seat
belts with a buckle
tongue that slides freely
along the belt without
locking into place; or
b) Seat belts equipped
with an emergency
locking retractor (ELR).
Consult your vehicle owner’s manual before
installing the locking clip.
To see an example of seat belt types and to properly
install a locking clip, go to p. 53.
46
Install with Vehicle Seat Belt
3.Route seat belt through forward-facing
belt path.
6.Install locking clip,
if necessary.
47
Forward-facing Installation with
Vehicle Seat Belt
This page is intentionally blank.
7.Ensure child
restraint is secure.
Try to move the child
restraint in all directions.
8.Connect and tighten
tether strap.
Connect the tether hook
to the anchor behind the
vehicle seat, as shown.
Pull the strap and tighten
the tether securely.
IMPORTANT: If your tether strap is too short to reach from
your child restraint to your vehicle tether anchor, you will need
a Tether Extender. Please call ParentLink at 1-800-233-5921.
48
Install with Vehicle Seat Belt
Vehicle Belt
Path
IMPORTANT: To properly
secure this child restraint, it
MUST NOT move more than
1 inch (25 mm) from side-toside or from front-to-back at
the vehicle belt path.
If you can not tightly secure
the child restraint, try again,
move it to another location,
or install with the LATCH
system.
49
General Information
Operating the SureLatch™ Connectors
Operating the Quick Connectors™
Release Button
To remove the SureLatch™
connector from a LATCH
anchor or its storage D-ring,
press the red Release Button.
Release Button
When the LATCH strap is in
the rear-facing belt path,
store each SureLatch™ connector by snapping it onto the
rear D-rings.
When the LATCH strap is in
the rear-facing belt path,
store each Quick Connector™
by snapping it onto the
D-rings, as shown.
General Information
When the LATCH strap is
in the forward-facing belt
path, store each SureLatch™
connector by snapping it
onto the forward D-rings.
When the LATCH strap is
in the forward-facing belt
path, store each Quick
Connector™ by snapping it
onto the D-rings, as shown.
To remove the Quick
Connector™ from a LATCH
anchor or its storage D-ring,
press the red Release Button.
50
51
Adjusting the Recline Position
This child restraint can be adjusted into three positions.
Squeeze the recline lever at
the bottom of the child
restraint, as shown, and
select the desired recline
position.
IMPORTANT: After adjusing
the recline position, rock the
child restraint back and forth
to make sure it is securely
locked in the desired positon.
Recline Lever
CORRECT RECLINE POSITIONING
• In rear-facing position: Use Recline Position #1 ONLY.
• In forward-facing position: Use Recline Position #2
for children who weigh 20 – 40 lbs (9 – 18 kg); use
Recline Position #3 for children who weigh 20 – 65 lbs
(9 – 29.4 kg).
Removing Seat Pad
EZ Off Pad
Enclosure
1.Disconnect both
LATCH connectors
from D-rings on seat
pad.
Installing the Locking Clip
To view a video about installing a locking clip, go to www.
evenflo.com.
Use the locking clip with:
• Lap/shoulder seat belt
combinations that have a
buckle tongue that slides
freely along the belt
without locking into place;
or
• Seat belts equipped with an emergency locking
retractor (ELR). Some ELR vehicle belts can be switched so
that they lock when tightened.
Consult your vehicle owner’s manual before
installing the locking clip.
Locking Clip
WARNING
• Remove locking clip from vehicle
seat belt when not used with a
child restraint, or the vehicle seat
belt will not properly restrain an
adult or child. Serious injury could
occur.
• DO NOT use the locking clip in
booster mode.
1.Using your full weight,
press down on the child
restraint as you tighten
the seat belt.
enclosure.
3.Disconnect all seat
pad hooks. Remove
the seat pad.
52
General Information
2.Open “EZ Off” pad
53
Installing the Locking Clip
2.Hold the lap/shoulder
belts together just
behind the free sliding
buckle tongue while you
unfasten the seat belt.
3.While holding the belts
1/2 in.
(13 mm)
and buckle tongue,
thread the locking clip
onto the seat belt, and
slide it into place.
Note: Locking clip must
be placed within 1/2 in.
(13 mm) of seat belt
buckle.
Installing the Accessories
WARNING
• Use the fold-down cup holder with the child restraint in the
forward-facing position ONLY.
• DO NOT use the cup holder to store bottles or hard
containers. Only for use with soft cups (such as styrofoam
or paper).
• DO NOT place any cups that contain hot liquids
(such as coffee or tea) in the accessories.
• DO NOT attach any other item to this child restraint
unless it has been certified for use with this specific child
restraint.
4.Buckle the seat belt with
the locking clip in place.
General Information
Return to the installation procedure:
• Rear-facing installation – Step 6, page 30
• Forward-facing installation – Step 7, page 48
To install the fold-down cup holder on either side of
the restraint, move seat pad out of the way and install
on the side, as shown.
To use, flip it open.
54
55
Installing the Accessories
WARNING
Use the Body Pillow and Infant Head Support with the
child restraint in the rear-facing position ONLY.
To attach the head pillow,
insert the strap through
the seat pad, as shown,
and connect to the
Velcro™ tab beneath.
The optional body pillow is used to help support the
child by placing it in the restraint, as shown.
• DO NOT lubricate or immerse the SureLatch™ connectors,
the buckle, or any other part of this child restraint.
• Plastic and metal parts may be wiped clean with
mild soap and water and dried with a soft cloth.
Do not use abrasive cleaners or solvents.
• Take care not to damage any labels.
• The harness can be wiped clean with mild soap and
water. Allow harness to air dry. DO NOT immerse
buckle in water.
• The seat pad can be machine washed separately in
cold water, delicate cycle. Tumble dry 10 – 15 minutes
on low heat.
• NEVER use child restraint without the seat pad.
Tip!
•
To help protect the
vehicle upholstery, place a
towel beneath and behind
the child restraint.
General Information
IMPORTANT:
• The optional head pillow (Infant Head Support) should
lie flat against the seat back, as shown. Be sure to cut
off and discard the plastic attachment between the head
support and the seat pad. Small parts may be a choking
hazard.
• Support the child’s head. Infants may have difficulty
breathing when in a sitting position. Using additional
padding or pillows behind the infant’s head, or failure
to properly recline the child restraint could increase the
child’s risk of serious injury or death.
Care and Cleaning
56
57
Replacement Parts
Proper Disposal of this Child Restraint
At the end of this child restraint’s useful life, Evenflo
encourages you to dispose of it properly. Most of the
components in this child restraint are recyclable.
1. Remove all fabric and padding.
2. Remove all screws and disassemble the restraint.
3. Recycle all plastic/foam parts and discard the rest.
If your local recycling center won’t accept the padding,
you may dispose of it in the landfill.
Note: Evenflo uses recycled materials in the
manufacturing process whenever possible but never
for components that are critical for safety.
Not available on all models.
You can order replacement parts on-line at www.evenflo.com
or contact Evenflo at 1-800-233-5921. When you contact
us, please have the product model number and date of
manufacture (found on the back of the child restraint).
Cup
Holder
Locking
Clip
Upper Seat
Foam
To prevent injury due to hidden damage, lost instructions, outdated technology, etc., discontinue use of this
restraint after eight years, or if it has been involved in a
crash.
Body
Pillow
Head
Pillow
Lower Seat
Foam
Tether
Extender
Para instrucciones en Español, llamar al: 1-800-233-5921
OWNER’S MANUAL
Keep for future use.
™
Momentum
Child Restraint System
WARNING
To reduce the risk
of SERIOUS INJURY or
DEATH, read this owner’s
manual prior to installing
and using this child
restraint.
© Evenflo Company, Inc. 2008
2570xxxx 7/08
Para instrucciones en Español, llamar al: 1-800-233-5921
LATCH Strap with
SureLatch™ Connectors
Seat Pad
Keep for future use.
™
Momentum
Child Restraint System
WARNING
To reduce the risk
of SERIOUS INJURY or
DEATH, read this owner’s
manual prior to installing
and using this child
restraint.
© Evenflo Company, Inc. 2008
58
LATCH Strap with
Quick Connectors™
General Information
After thoroughly reading and
following these instructions,
store them in the slots provided
on the back of the child
OWNER’S MANUAL
restraint, as shown.
2570xxxx 7/08
59
Limited Warranty
For a period of 90 days from the original purchase of this Product, Evenflo warrants to the original end user (“Purchaser”) this
Product (including any accessories) against defects in material
or workmanship. Evenflo’s sole obligation under this express
limited warranty shall be, at Evenflo’s option, to repair or replace any Product that is determined to be defective by Evenflo
and determined to be covered by this warranty.
Repair or replacement as provided under this warranty is the
exclusive remedy of the Purchaser. Proof of purchase in the
form of a receipted invoice or bill of sale evidencing that the
Product is within the warranty period must be presented to obtain warranty service. This express limited warranty is extended
by Evenflo ONLY to the original Purchaser of the Product and is
not assignable or transferable to subsequent purchasers or end
users of the Product. For warranty service, contact Evenflo’s
ParentLink Consumer Resource Center at 1-800-233-5921 or
www.evenflo.com.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW,
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS HEREBY
DISCLAIMED. EVENFLO SHALL NOT BE LIABLE FOR ANY
INCIDENTAL, CONSEQUENTIAL, SPECIAL OR PUNITIVE DAMAGES OF ANY KIND FOR BREACH OF THE EXPRESS LIMITED
WARRANTY ON THIS PRODUCT, OR ANY WARRANTY IMPLIED
BY OPERATION OF LAW. OTHER THAN THE EXPRESS LIMITED
WARRANTY SET FORTH ABOVE, THERE ARE NO OTHER WARRANTIES THAT ACCOMPANY THIS PRODUCT AND ANY ORAL,
WRITTEN OR ANY OTHER EXPRESS REPRESENTATION OF ANY
KIND IS HEREBY DISCLAIMED.
Answers. Advice. Affirmation.™
60
• www.evenflo.com
• USA: 1-800-233-5921, 8 AM to 5 PM E.T.
• Mexico: 01-800-706-12-00
Answers. Advice. Affirmation.™
• www.evenflo.com
• USA: 1-800-233-5921, 8 AM to 5 PM E.T.
• Mexico: 01-800-706-12-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising