Encore ENHWI-N3, N150 User manual

Encore ENHWI-N3, N150 User manual
ENHWI-N3
802.11n Wireless Router
User Manual
1
TABLE OF CONTENTS
1
INTRODUCTION ........................................................................................................................3
2
KEY FEATURES..........................................................................................................................4
3
PACKAGE CONTENTS..............................................................................................................5
4
PRODUCT LAYOUT ...................................................................................................................6
5
NETWORK + SYSTEM REQUIREMENTS.............................................................................8
6
ENHWI-N3 PLACEMENT..........................................................................................................8
7
SETUP LAN, WAN .......................................................................................................................9
8
PC NETWORK ADAPTER SETUP (WINDOWS XP) ............................................................10
9
BRING UP ENHWI-N3..............................................................................................................12
10
SMART WIZARD ......................................................................................................................12
11
INITIAL SETUP ENHWI-N3....................................................................................................26
12
AP ROUTER MODE..................................................................................................................27
13
REPEATER MODE ..................................................................................................................84
APPENDIX A – FCC INTERFERENCE STATEMENT..................................................................96
APPENDIX B – IC INTERFERENCE STATEMENT .....................................................................97
2
I - Introduction
Congratulations on your purchase of ENHWI-N3 802.11n Wireless Router.
ENHWI-N3 is backward compatible with wireless devices running under the
802.11g and 802.11b technologies. ENHWI-N3 is not only a Wireless Access
Point, but also a wireless Repeater that extends your wireless coverage when
used as a Repeater Mode in a established Local Area Networking or LAN, as
well as 4-port 10/100 Mbps full-duplex Switch that connects your wired Ethernet
LAN devices together at incredible speed.
At 150 Mbps wireless transmission rate, the Access Point built into the router
uses advanced MIMO (Multi-Input, Multi-Output) technology to transmit multiple
streams of data into a single wireless channel providing a seamless access to
multimedia contents. Its robust RF signal travels farther, eliminates dead spots
and extends network range. For data protection, wireless security and privacy,
the ENHWI-N3 encodes all wireless transmissions with WEP, WPA, and WPA2
data encryptions.
With built-in DHCP Server & a powerful SPI firewall, the ENHWI-N3 protects
your computers against intruders and known Internet attacks, and still provides
safe and secured VPN pass-through. With data rate at incredible speed and QoS
function, the ENHWI-N3 is ideal for media-centric applications such as streaming
video, internet gaming, and VoIP telephony to run multiple media-intense data
streams through the network at the same time, with no degradation in
performance.
3
II - Key Features
Features
Incredible Data Rate up to 150 Mbps**
Advantages
Easily handled heavy data loads
such as MPEG audio / video
streaming,
IEEE 802.11b/g/n Compliant
Fully Interoperable with IEEE
802.11b/g/n compliant devices
with legacy protection
Four 10/100 Mbps Fast Switch RJ-45
Scalability. Extend your network
Ports (with Auto-Crossover)
computers.
Firewall supports, DMZ, MAC Filter, IP
Use to prevent attacks from
Filter, URL Filter, ICMP Blocking, SPI,
hackers or viruses from the
Port Mapping, Port Forwarding, Port
internet
Trigger
Support 802.1x Authenticator, 802.11i
Provide mutual authentication
(WPA/WPA2, AES), VPN pass-through
(Client and dynamic encryption
keys to enhance security)
WDS (Wireless Distribution System)
Make Wireless AP and Bridge
mode simultaneously as a
wireless repeater
** Theoretical wireless signal rate based on IEEE standard of 802.11a, b, g, n chipset used. Actual
throughput may vary. Network conditions and environmental factors lower actual throughput rate.
All specifications are subject to change without notice.
4
III - Package Contents
Check and make sure that none of the items listed below are missing. Do not
discard the packing materials, in case of return; the unit must be shipped back in
its original packaging.
1. ENHWI-N3 Wireless 802.11n Router
2. 100V~240V Power Adapter (Use only the supplied power adapter)
3. One piece 2 dBi 2.4 GHz SMA Upgradeable Antenna
4. Quick Installation Guide
5. CD-ROM (Smart Install and User’s Manual)
5
IV - Product Layout
Front Panel View
LED Lights
Description
Lights up in Red when powered ON.
POWER
Blinks on TEST/RESET
Lights up in Green when Wireless LAN is
WLAN
enabled. Blinks on traffic
Blinks in Green on data traffic
1 to 4
Lights up in Green when WAN port is use
WAN
6
Rear View
Item
Description
Press and release this button to reboot the
Reset
device.
Press and hold this button for 10 seconds
to load the factory default settings of the
system.
WPS™
Click this button to start WPS™ function.
Power connector, connects to DC 12V 1As
DC 12V
Power Adapter
Ports
LAN1 ~ LAN4
1
to
4
Local
Area
Network
(LAN)10/100 Mbps RJ-45 ports
Wide Area Network (WAN) port or
WAN
Internet Port. Connects to xDSL or Cable
Modem
7
V - Network + System Requirements
To begin using the ENHWI-N3, make sure you meet the following as minimum
requirements:
h
PC / Notebook Computer
h
Operating System – Microsoft™
Windows® 98SE/ME/XP/2000/
Windows Vista™
h
1 Free Ethernet port
h
Wi-Fi adapter card – optional.
h
External xDSL (ADSL) or Cable modem with an Ethernet port (RJ-45).
h
A Web Browser (Internet Explorer, Safari, Firefox, Opera etc.)
h
Few Ethernet compatible CAT5 or better cables.
VI - ENHWI-N3 - Where to place
You can place ENHWI-N3 on a desk or other flat surface, or you can mount it on
a wall. For optimal performance, place your ENHWI-N3 Wireless Router in the
center of your office (or your home) in a location that is away from any potential
source of interference, such as a metal wall or microwave oven. This location
must be close to a power connection and your ADSL/Cable modem. If the
antennas are not positioned correctly, performance loss can occur.
8
VII - Setup LAN, WAN
LAN connection:
Connect Ethernet cable between your PC/Notebook LAN port
& one of the 4 available LAN ports on ENHWI-N3.
WAN connection:
Connect
Ethernet
cable
between
WAN
port
of
your
ADSL/CABLE modem & WAN port of ENHWI-N3. Make sure
your ADSL/CABLE modem is already setup and working well.
Contact your ISP (Internet Service Provider) if you have any
questions.
9
VIII - PC Network Adapter Setup (Windows XP)
•
Assuming your PC or Laptop is equipped with a Network Interface Card. Click
on START Æ select “Control panel” Æ From the Control Panel Window
select “Network Connections”
•
Right-click (Use the right button of your mouse) the “Local Area
Connection” icon then select and click “Properties”
10
•
Click to Highlight the “Internet Protocol (TCP/IP)” then click “Properties”
button
•
Select the “General” tab.
a. ENHWI-N3 supports the DHCP function, please select both “Obtain an IP
address automatically” and “Obtain DNS server address automatically”
11
IX - Power up the ENHWI-N3
Connect the supplied power-adapter to the power port and connect it to a wall
power outlet. The ENHWI-N3 automatically enters and run the self-test phase.
The Power LED will light a steady red light indicating that the ENHWI-N3 is
ready for operation.
X - Smart Wizard
Before you start the ENHWI-N3 router’s Smart Wizard check for the followings:
•
Internet connection should be setup & ready to use (ADSL or cable modem).
•
Modem must provide an RJ-45 port to connect with a ENHWI-N3 Router
•
Microsoft Windows compatible PC/Notebook with UPnP enabled Network
Interface Card adapter. (This can be found in your network cards advanced
properties within MS Windows)
•
CAT 5 network cable(s), RJ-45 port on PC/Notebook.
Step 1: Connect ENHWI-N3 “WAN” port & your Modem’s LAN port with RJ45
cable.
Step 2: Power-up the ENHWI-N3. The red power LED in the front the panel should
light up & stay on to indicate that the router is ready
Step 3: Connect one of the four available LAN ports to the PC/Notebook RJ-45 NIC
port with a CAT 5 RJ-45 network cable.
Step 4: Insert the ENHWI-N3 CD into your CDROM drive and the “SMART
WIZARD” should run automatically after just a few seconds. If not, open the
Windows Explorer, go to the root directory of the CD. Double click on the
Wizard.exe file.
12
A welcome screen will pop up a few seconds and then will disappear.
13
NOTE: The product picture may be different from what you have
Click Setup Wizard to run basic setup settings of your ENHWI-N3.
Click User Manual to open the user manual.
Click Adobe Reader to install Adobe Acrobat reader on your PC/Notebook.
Click EXIT when finish or anytime you want to abort.
14
Setup Wizard
Click
to proceed. Click <Exit> to abort.
15
Make sure your DSL/CABLE modem is setup and working prior to this installation
procedures. If not, call your Internet Service Provider and have them check and help
you in setting up your DSL/Cable modem.
Click
to proceed.
16
Check the MODEM and ENHWI-N3 connection. It should be as shown below.
17
Check power connection for modem as well as ENHWI-N3.
Make sure the antenna is connected to rear panel of ENHWI-N3.
Click <Next> to proceed.
Notice the LED will light up at this stage. If not, check your procedures again.
18
Click
to configure WAN & Wireless settings.
19
Enter the factory default username is admin and password is also admin. Click
to continue. Your default browser screen will connect to the ENHWI-N3 User
Interface screen using the factory default address http://192.168.0.1 .
Click
to enter the mode selection screen.
20
Select the mode your ENHWI-N3 is going to use. The Setup Wizard will skip the
WAN configuration under AP Repeater Mode.
Click
and your ENHWI-N3 will automatically detect your “Internet” Network
settings.
21
The Smart Wizard will detect the DHCP and PPPoE connections automatically. In
the picture above it shows that the Smart Wizard detected a DHCP server. You can
choose the detected service type or select “Others” to setup the WAN settings
manually.
22
Here, you can configure the host name and MAC address of the ENHWI-N3. The
“Clone MAC Address” button clones the MAC address of your PC and use it as the
MAC address of your ENHWI-N3 router instead of the real MAC address of the
router.
The Smart Wizard has finished setting up the WAN Configuration portion. Click
to proceed to other portions.
23
Setting up Wireless LAN
Enter the name for your wireless network SSID (the default is ENCORE59FE74) and
security key (default is 1234567890). Move and point your mouse over to the
security level blocks from the weakest (red block) to the strongest (green block), and
click on the selected block to select the level of security you desired. The “Key” type
will depend on the wireless security you selected. If you choose WEP as the wireless
security you will be prompted whether an ASCII or Hexadecimal is your preferred key
type. Hexadecimal requires 10 character digits on the KEY: field.
Click
to proceed
24
To save configuration changes click
NOTE:
After the Wireless settings are saved and the ENHWI-N3 is rebooted, you
need to reconnect your WLAN client using the new security settings you just
changed. You will need to reenter the new wireless security key for the client
and the ENHWI-N3 reestablish wireless connections.
25
XI – How to login to the ENHWI-N3 web
based Graphical User Interface
The ENHWI-N3 use a web based user interface for setting up your router’s
configuration, it can be access through your web browser such as Internet
Explorer or Mozilla Firefox.
ENHWI-N3 web based user interface login procedure
1. OPEN your browser (Example: Internet Explorer, Mozilla, Netscape, etc).
2. Type-in http://192.168.0.1 exactly in address field and hit the [Enter] key on
your keyboard.
3. Type-in the ENHWI-N3 Username and Password (the factory default is admin
and admin)
4. Click
to navigate into the ENHWI-N3 configuration home page.
5. You will see the configuration home page of the ENHWI-N3 as follows.
26
ENHW-N3 Home Page Screen
XII - The AP Router Mode
„ SYSTEM
Shows the Uptime, Hardware information, Serial number as well as the Firmware
version information and other vital information
z Status Tab
This page allows you to monitor the status of your router.
27
1. WAN Settings: Scroll down to see the full information. This section displays
whether the WAN port is connected to a Cable / DSL modem. It also displays
the router’s WAN IP address, Subnet Mask, ISP Gateway, MAC address and
the Primary DNS.
28
2. LAN Settings: Scroll down to see this section. Displays the ENHWI-N3 Router
LAN port’s current information. It also shows whether the DHCP Server is enabled or
disabled.
2. WLAN Settings: Scroll down to see this section. This section displays the
current WLAN configuration settings. The wireless configuration details such as
the SSID, Security settings, ESSID, BSSID, Channel number and wireless
clients connected info are briefly shown.
z LAN Tab
29
The LAN Tab is where LAN settings can be change. If you are an entry level user,
after hooking up the cables, try to access the internet from your computer. If you can
open a website with no problem, leave the settings as it is. If changes were made,
click the
button to save the changed configurations.
LAN IP
IP address: 192.168.0.1 is the router’s LAN manufacturers default IP address (this
will also be the “Default Gateway” IP address of your LAN clients). It
can be change based on your LAN design and configurations. Typical
designs don’t need to change this IP address.
IP Subnet Mask: 255.255.255.0 specifies the Subnet Mask address for your LAN
segment. This is based on the IP address range used.
802.1d Spanning Tree: This is disabled by default. If 802.1d Spanning Tree
function is enabled, this router will use the spanning
tree protocol to prevent network loops.
30
DHCP Server
DHCP Server: This can be enabled or disabled, “Enabled” by default.
Lease time: Lease time assigned to all IP address by the DHCP server.
Start IP: This is the first IP address in the IP pool range in which are being
assigned and leased to DHCP clients.
End IP: This is the end of the IP address pool range
Domain Name: The Domain Name for the existing or customized network.
z DHCP Tab
This is where to view the current LAN clients that have assigned or leased IP
address by the DHCP server. This screen also shows all the DHCP clients that are
currently connected to your network. The table shows the assigned or leased IP
address, MAC address and the lease expiration data for each DHCP clients. Use
31
the <Refresh> button to update the available information. Click the <Refresh>
button to get the updated table.
You can click to put a check mark on “Enable Static DHCP IP“. It is possible to
add more static DHCP IP addresses. They are listed in the table “Current Static
DHCP Table“. IP address can be deleted if wanted to.
Click the <Apply> button to save the changes made to the configuration.
z Schedule Tab
This page allows users to set up a scheduled function for the Firewall and Power
Saving features of the ENHWI-N3 router.
.
Edit the scheduled function to allow configuration for firewall or power savings
services. Fill in the schedule and select type of service you desired. Click <Apply>
to
save
the
32
settings.
The “Schedule” table screen lists the pre-scheduled services. Select any of the
schedules by using the check box located on the right side of each line to edit or
Delete selected schedule line.
z Event Log Tab
33
On this “Event Log” screen, it displays all events and events information occurred
after the start-up. Scroll down to see more. The Event Log can be saved to the
local file-storage device such as hard disc drive by using the <Save> button, or
the Event Log can be emptied using the <Clear> button. Use the <Refresh>
button to reset the Event Log and to get the most updated information. When the
router is powered OFF, the Event Log will be wiped out and will come up empty.
The saved logs can be uploaded and viewed again.
z Monitor Tab
This screen shows the histogram of the network connection on WAN, LAN &
WLAN. Auto refresh keeps information updated frequently.
34
z Language Tab
This is where you select preferred language.
35
„ WIZARD
Click Wizard to configure the basic functionalities of the ENHWI-N3 Router. A popup
Setup Wizard Window will be immediately displayed. If the popup window for Setup
Wizard failed to appear check your Popup Settings and make sure popup is allowed
at least temporarily for this purpose. Before you continue, check all the needed
cables if they are properly hooked up. Check your DSL or Cable Modem if working
properly and is connected to your ISP and then click <Next>. Refer to the Smart
Wizard section for more details.
„ INTERNET
- Status
This page shows the current Internet connection type and status
36
- Dynamic IP
Use the MAC address when registering for the Internet service, and do not change
it unless required by your ISP. If your ISP use the MAC address of the Ethernet
card as an identifier, connect only the PC with the registered MAC address to the
broadband router and click the <Clone MAC Address> button. This will replace
the current MAC address with the already registered Ethernet card MAC address.
37
Host Name: This is optional.
MAC address: The default value is set to the WAN’s physical address or MAC of
the broadband router.
- Static IP
If your ISP Provider has assigned a fixed public IP address for you to use, enter the
assigned IP address, Subnet Mask, Default Gateway IP address, Primary and
Secondary DNS (if available) of your ISP provider.
38
- Point-to-Point Protocol over Ethernet(PPPoE)
39
Login / Password: Enter the PPPoE username and password assigned by your
ISP Provider.
Service Name: This is optional.
Maximum Transmission Unit (MTU): This is the maximum size of the packets.
Type: Keep Connection - will stay connected to the Internet
Automatic Connection - automatically connects to the Internet when
an application needs it, and drops the connection after the designated
idle time period.
Manual Connection – manually connect and disconnect to the internet
by the user
Idle Timeout (available only under Automatic Connection): This is a
maximum period of time for which the Internet connection is maintained
during inactivity. If the application is inactive for certain time designated
here the internet connection will be automatically dropped.
- Point-to-Point Tunneling Protocol (PPTP)
40
PPTP allows the secure connection over the Internet by simply dialing in to a local
point provided by your ISP provider. The image screen allows client PCs to establish
a normal PPTP session and provides hassle-free configuration of the PPTP client on
each client PC.
Click <Apply> to save configuration and connect to ISP provider.
„ WIRELESS
- Basic
In basic setting page, you can set wireless Radio, Mode, Band, SSID, and Channel.
41
Radio: You can turn on/off wireless radio. If wireless Radio is turned off, the
ENHWI-N3 will not take wireless connections.
Mode: Three operation modes for selections, the AP router and AP router
with WDS. If you choose AP Router Mode, there will be two selections
under it, the AP or WDS function in the drop-down menu.
Band: You can select the wireless standards running on your network
environment such as the following:
2.4 GHz(B): If all your clients are using 802.11b
2.4 GHz(N): If all your clients are using 802.11n
2.4 GHz(B+G): If both 802.11b or a 802.11g
2.4 GHz(G): If all your clients are using 802.11g
2.4 GHz(B+G+N): If your clients are mixed using 802.11b,
802.11g, or 802.11n
Enable ESSID: ENHWI-N3 supports up to 4 SSID. Use the down arrow to
select the number of SSID you wanted to have in your wireless
LAN. Once established you can set the security policy settings
for each. See “Policy” section for more details.
42
ESSID1 to ESSID4: ESSID is the name of your wireless network. It is
recommended to use a unique name to identify your wireless
device in the LAN. This is case sensitive and up to 32 printable
characters.
Auto Channel: Disable by default. If Enabled will automatically search all
channels and automatically change to the clearest channel
detected. Different items are visible below the Auto Channel.
Channel: Channel 11 by default. This is visible only when the Auto Channel is
disabled. You can enter your preferred channel number here for the
ENHWI-N3 wireless LAN.
Check Channel Time: This menu is visible only when the Auto Channel is
enabled. Selections are from One Hour to One Week.
This is the duration of when will the ENHWI-N3 check
for and use the clearest channel in the area
automatically.
- WDS with AP Router
Wireless Distribution System. The WDS is a way of interconnecting wireless
routers and allow an extended wireless network coverage using multiple wireless
routers without the use of a wired backbone. Each WDS AP requires the same
channel and encryption type to work.
43
MAC address 1~4: Please enter the MAC address(es) of the neighboring APs
that participates in the WDS. A maximum of 4 devices are
allowed.
Set Security: WDS Security depends on your AP security settings. Note: It
does not support mixed mode such as WPA-PSK/WPA2-PSK
Mixed mode.
44
- Advanced
On this tab you can set the advanced wireless settings. If you’re in doubt what to
enter or use here, leave these settings as it is. This is for advance users only. Wrong
parameters can make the router un-operational.
Fragment Threshold: Default value is 2346.Specifies the maximum size of a
packet during the fragmentation of data to be transmitted. If you set this value
too low, it will result in a bad performance.
RTS Threshold: Default value is 2347. When the packet size is smaller than
the RTS threshold, the wireless router will not use the RTS/CTS mechanism to
send this packet.
Beacon Interval: Default value is 100. This is the interval of time that this
wireless router broadcasts a beacon. A Beacon is used to synchronize the
wireless network.
45
DTIM Period: Default value is 1. Enter a value between 1 and 255 for the
Delivery Traffic Indication Message (DTIM). A DTIM is a
countdown informing clients of the next window for listening to
broadcast and multicast messages.
Data Rate: The “Data Rate” is the rate that this access point uses to transmit
data packets. The access point will use the highest possible
selected transmission rate to transmit the data packets.
N Data Rate: The “Data Rate” is the rate that this access point uses to transmit
data packets for N compliant wireless nodes. Highest to lowest
data rate can be fixed.
Channel Bandwidth: This is the range of frequencies that will be used.
Preamble Type: The “Long Preamble” can provide better wireless LAN
compatibility while the “Short Preamble” can provide better
wireless LAN performance.
CTS Protection: It is recommended to enable the protection mechanism. This
mechanism can decrease the rate of data collision between
802.11b and 802.11g wireless stations. When the protection
mode is enabled, the throughput of the AP will be a lower due
to an increase of data frame transmission.
TX Power: 10% to 100%. Default value is 100%.
- Security
ENHWI-N3 provides complete wireless LAN security types. Selections are WEP,
IEEE 802.1x, IEEE 802.1x with WEP, WPA with pre-shared key or PSK and
WPA with RADIUS. With these wireless securities, unauthorized access can be
prevented. Make sure all other wireless stations use the same security type, and
were setup with the same security key.
46
ESSID Selection: ENHWI-N3 router supports multiple ESSID, you can name your
wireless ESSID here.
Broadcast ESSID: If you enabled “Broadcast ESSID”, every wireless station located
within the coverage of this Router can see this ESSID. If you are
building a public wireless network, enabling this feature is
recommended. Disabling “Broadcast ESSID” can provide better
security.
WMM: Wi-Fi Multi Media if enabled supports QoS to dedicate line and other resource
for better audio, video and voice streaming to a particular station and
applications.
Encryption: If set to Disable, the router will have no protection against uninvited
wireless guests, your LAN will be prone to hackers. It is highly
recommended to Enable this function and set your own wireless
security.
Enable 802.1x Authentication
47
IEEE 802.1x is an authentication protocol using RADIUS server. When this is
Enabled, every LAN user must use an account to login to this Access Point
before accessing the wireless LAN. The authentication is processed by a
RADIUS server. This mode only authenticates users by IEEE 802.1x, but it does
not encrypt the data during communication.
WEP Encryption
When you select 64-bit or 128-bit WEP key, you have to enter WEP keys to
encrypt data. You can generate the key by yourself. You can enter up to four
WEP keys and select one of them as a default key. The AP can receive any
packet encrypted by one of the four keys.
48
Authentication Type: There are two authentication types: "Open System" and
"Shared Key". Both AP and wireless client must be
configured with the same authentication type.
Key Length: You can select the WEP key length for encryption, 64-bit or 128-bit.
The larger the key will be the higher level of security is used, but
the throughput will be lower.
Key Type: You may select ASCII Characters (alphanumeric format) or
Hexadecimal Digits (in the "A-F", "a-f" and "0-9" range) to be the
WEP Key.
Default Key: It’s the key used to encrypt data.
Key1 - Key4: The WEP keys are used to encrypt data transmitted in the wireless
network. Use the following rules to setup a WEP key on the
device.
49
64-bit WEP: input 10-digits Hex values (in the "A-F", "a-f" and "0-9" range)
or 5-digit ASCII character as the encryption keys.
128-bit WEP: input 26-digit Hex values (in the "A-F", "a-f" and "0-9" range)
or 13-digit ASCII characters as the encryption keys.
Click <Apply> at the bottom of the screen to save the above configurations.
WPA Pre-Shared Key Encryption
Wi-Fi Protected Access (WPA) is an advanced security standard. You can use a
pre-shared key to authenticate wireless stations and encrypt data during
communication. It uses TKIP or CCMP (AES) to change the encryption key
frequently. The encryption key is not easy to be cracked by hackers. This is the
best security available.
50
WPA-RADIUS Encryption
Wi-Fi Protected Access (WPA) is an advanced security standard. You can use
an external RADIUS server to authenticate wireless stations and provide the
session key to encrypt data during communication.
It uses TKIP or CCMP (AES) to change the encryption key frequently. Press
<Apply> button when you are done.
51
- MAC Address Filtering
This
wireless
router
supports
MAC
Address
Control,
which
prevents
unauthorized clients from accessing your wireless network.
Enable wireless access control: Enable the wireless access control function
Adding an address into the list
Enter the "MAC Address" and "Description" of the wireless station to be
added and then click <Add>. The wireless station will now be added into
the "MAC Address Filtering Table" below. If you are having any difficulties
filling in the fields, just click "Reset" and both "MAC Address" and
"Description" fields will be cleared.
Remove an address from the list
If you want to remove a MAC address from the "MAC Address Filtering
Table", select the MAC address that you want to remove in the list and
then click "Delete Selected". If you want to remove all the MAC addresses
from the list, just click the <Delete All> button. Click <Reset> will clear
your current selections.
52
Click <Apply> at the bottom of the screen to save the above configurations.
- Wi-Fi Protected Setup™ (WPS™)
WPS™ is the simplest way to establish a connection between the wireless clients
and the wireless router. You don’t have to select the encryption mode and fill in a
long encryption passphrase every time when you try to setup a wireless
connection. You only need to press a button on both wireless client and wireless
router, and the WPS will do the rest for you.
The wireless router supports two types of WPS, the WPS via Push Button and
WPS via PIN code. If you want to use the Push Button, you have to push a
specific button on the wireless client or in the utility of the wireless client to start
the WPS mode, and switch the wireless router to WPS mode. You can simply
push the WPS button of the wireless router, or click the ‘Start to Process’ button
in the web configuration interface. If you want to use the PIN code, you have to
know the PIN code of the wireless client and switch it to WPS mode, then fill-in
the PIN code of the wireless client through the web configuration interface of the
wireless router.
WPS: Check the box to enable WPS function and uncheck it to disable the WPS
function.
53
WPS Current Status: If the wireless security (encryption) function of this
wireless router is properly set, you’ll see a ‘Configured’
message here. Otherwise, you’ll see ‘UnConfigured’.
Click the “Release Configuration” can clear the security
settings of the 1st SSID.
Self Pin Code: This is the WPS PIN code of the wireless router. You may need
this information when connecting to other WPS-enabled
wireless devices.
SSID: This is the network broadcast name (SSID) of the router.
Authentication Mode: It shows the active authentication mode for the wireless
connection.
Passphrase Key: It shows the passphrase key that is randomly generated by
the wireless router during the WPS process. You may need
this information when using a device which doesn’t support
WPS.
Interface: If device is set to repeater mode, you can choose “Client” interface to
connect with other AP by using WPS, otherwise you may choose
“AP” interface to do WPS with other clients.
WPS via Push Button: Press the button to start the WPS process. The router
will wait for the WPS request from the wireless devices
within 2 minutes.
WPS via PIN: You can fill-in the PIN code of the wireless device and press the
button to start the WPS process. The router will wait for the WPS
request from the wireless device within 2 minutes.
54
- Client List
WLAN Client Table shows the Wireless clients associated to this Wireless
Router.
- Policy
The Broadband router can allow you to set up the Wireless Access Policy up to 4
SSID’s.
55
„ FIREWALL
The Broadband router provides extensive firewall protection by restricting connection
parameters, thus limiting the risk of hacker attacks, and defending against a wide
array of common Internet attacks. However, for applications that require unrestricted
access to the Internet, you can configure a specific client/server as a Demilitarized
Zone (DMZ).
Note:
To enable the Firewall settings select Enable and click Apply
- Advanced
You can allow the VPN packets to pass through this Broadband router.
56
- Demilitarized Zone (DMZ)
If you have a client PC that cannot run an Internet application (e.g. Games)
properly behind the NAT firewall, then you can open up the firewall restrictions to
unrestricted two-way Internet access by defining a DMZ Host. The DMZ function
allows you to re-direct all packets going to your WAN port IP address to a
particular IP address in your LAN. The difference between the virtual server and
the DMZ function is that the virtual server re-directs a particular service/Internet
application (e.g. FTP, websites) to a particular LAN client/server, whereas DMZ
re-directs all packets (regardless of services) from your WAN IP address to a
particular LAN client/server.
Enable DMZ: Enable / Disable DMZ
LAN IP Address: Fill-in the IP address of a particular host in your LAN Network
or select a PC from the list on the right that will receive all the
packets originally from the WAN port/Public IP address.
Click <Apply> at the bottom of the screen to save the above configurations.
- Denial of Service (DoS)
57
The Broadband router's firewall can block common hacker attacks, including Denial
of Service, Ping of Death, Port Scan and Sync Flood. If Internet attacks occur the
router can log the events.
Flood: Protects the router from Sync Flood attack.
- MAC Filter
If you want to restrict users from accessing certain Internet applications / services
(e.g. Internet websites, email, FTP etc.), and then this is the place to set that
configuration. MAC Filter allows users to define the traffic type permitted in your
LAN. You can control which PC client can have access to these services.
58
Enable MAC Filtering: Check to enable or disable MAC Filtering.
Deny: If you select “Deny” then all clients will be allowed to access Internet
except the clients in the list below.
Allow: If you select “Allow” then all clients will be denied to access Internet
except the PCs in the list below.
59
Add PC MAC Address
Fill in “LAN MAC Address” and <Description> of the PC that is allowed /
denied to access the Internet, and then click <Add>. If you find any typo
before adding it and want to retype again, just click <Reset> and the fields
will be cleared.
Remove PC MAC Address
If you want to remove some PC from the "MAC Filtering Table", select the
PC you want to remove in the table and then click <Delete Selected>. If
you want to remove all PCs from the table, just click the <Delete All>
button. If you want to clear the selection and re-select again, just click
<Reset>.
Click <Apply> at the bottom of the screen to save the above configurations.
60
- IP Filter
Enable IP Filtering: Check to enable or uncheck to disable IP Filtering.
Deny: If you select “Deny” then all clients will be allowed to access Internet
except for the clients in the list below.
Allow: If you select “Allow” then all clients will be denied to access Internet
except for the PCs in the list below.
Add PC IP Address
You can click <Add> PC to add an access control rule for users by an IP address
or IP address range.
Remove PC IP Address
If you want to remove some PC IP from the <IP Filtering Table>,
61
select the PC you want to remove in the table and then click <Delete Selected>. If
you want to remove all PCs from the table, just click the <Delete All> button.
Click <Apply> at the bottom of the screen to save the above configurations.
- URL Filter
You can block access to some Web sites from particular PCs by entering a full
URL address or just keywords of the Web site.
Enable URL Blocking: Enable or disable URL Blocking
Add a URL Keyword
Fill-in the “URL/Keyword” field with your ur l/ keyword, and then click <Add>. You
can enter the full URL address or the keyword of the web site you want to block. If
you happen to make a mistake and want to retype again, just click "Reset" and the
field will be cleared.
62
Remove URL Keyword
If you want to remove some URL keywords from the "Current URL Blocking Table",
select the URL keyword you want to remove in the table and then click <Delete
Selected>. If you want remove all URL keywords from the table, click <Delete All>
button. If you want to clear the selection and re-select again, just click <Reset>.
Click <Apply> to save the above configurations
63
„ ADVANCED
- Network Address Translation (NAT)
Network Address Translation (NAT) allows multiple users at your local LAN site
to access the Internet using a single Public IP Address or multiple Public IP
Addresses. NAT provides Firewall protection from hacker attacks and has the
flexibility to allow you to map Private IP Addresses to Public IP Addresses for key
services such as Websites and FTP. Select Disable to disable the NAT function.
- Port Mapping
Port Mapping allows you to re-direct a particular range of service port numbers
(from the Internet / WAN Port) to a particular LAN IP address. It helps you to host
servers behind the router NAT firewall.
64
Enable Port Mapping: Enable or disable port mapping function.
Description: description of this setting.
Local IP: This is the local IP of the server behind the NAT firewall.
Protocol: This is the protocol type to be forwarded. You can choose to forward
“TCP” or “UDP” packets only, or select “BOTH” to forward both “TCP” and
“UDP” packets.
Port Range: The range of ports to be forward to the private IP.
Add Port Mapping
65
Fill in the "Local IP", “Protocol”, “Port Range” and "Description" of the setting to
be added and then click "Add". Then this Port Mapping setting will be added into the
"Current Port Mapping Table" below. If you find any typo before adding it and want
to retype again, just click <Reset> and the fields will be cleared.
Remove Port Mapping
If you want to remove a Port Mapping setting from the "Current Port Mapping
Table", select the Port Mapping setting that you want to remove in the table and then
click D<Delete Selected>. If you want to remove all Port Mapping settings from the
table, click <Delete All> button. Click <Reset> will clear your current selections.
Click <Apply> at the bottom of the screen to save the above configurations.
- Port Forwarding (Virtual Server)
Use the Port Forwarding (Virtual Server) function when you want different
servers/clients in your LAN to handle different service/Internet application type (e.g.
Email, FTP, Web server etc.) from the Internet. Computers use numbers called port
numbers to recognize a particular service/Internet application type. The Virtual
Server allows you to re-direct a particular service port number (from the
Internet/WAN Port) to a particular LAN private IP address (See Glossary for an
explanation on Port number).
66
Enable Port Forwarding: Enable or disable Port Forwarding.
Description: The description of this setting.
Local IP / Local Port: This is the LAN Client/Host IP address and Port number
that the Public Port number packet will be sent to.
Protocol: Select the port number protocol type (TCP, UDP or both). If you are
unsure, then leave it to the default “both” setting. Public Port enters the
service (service/Internet application) port number from the Internet that will be
re-directed to the above Private IP address host in your LAN Network.
Public Port: Port number will be changed to Local Port when the packet enters
your LAN Network.
Add Port Forwarding
67
Fill in the "Description" , "Local IP", "Local Port", "Protocol" and “Public Port”
of the setting to be added and then click <Add> button. Then this Virtual
Server setting will be added into the "Current Port Forwarding Table"
below. If you find any typo before adding it and want to retype again, just
click <Reset> and the fields will be cleared.
Remove Port Forwarding
If you want to remove Port Forwarding settings from the "Current Port
Forwarding Table", select the Port Forwarding settings you want to
remove in the table and then click "Delete Selected". If you want to remove
all Port Forwarding settings from the table, just click the <Delete All>
button. Click <Reset> will clear your current selections.
Click <Apply> at the bottom of the screen to save the above configurations.
- Port Triggering (Special Applications)
Some applications require multiple connections, such as Internet games, video
Conferencing, Internet telephony and others. In this section you can configure
the router to support multiple connections for these types of applications.
68
Enable Trigger Port: Enable or disable the Port Trigger function.
Trigger Port: This is the outgoing (Outbound) range of port numbers for this
particular application.
Trigger Type: Select whether the outbound port protocol is “TCP”, “UDP” or
“BOTH”.
Public Port: Enter the In-coming (Inbound) port or port range for this type of
application (e.g. 2300-2400, 47624)
Public Type: Select the Inbound port protocol type: “TCP”, “UDP” or “BOTH”
Popular Applications: This section lists the more popular applications that
require multiple connections. Select an application
from the Popular Applications selection. Once you
have selected an application, select a location (1-5) in
the “Add” selection box and then click the <Add>
button. This will automatically list the Public Ports
required for this popular application in the location (1-5)
you specified.
69
Add Port Triggering
Fill in the "Trigger Port", "Trigger Type”, “Public Port”, "Public Type",
"Public Port" and "Description" of the setting to be added and then Click
<Add>. The Port Triggering setting will be added into the "Current TriggerPort Table" below. If you happen to make a mistake, just click <Reset>
and the fields will be cleared.
Remove Port Triggering
If you want to remove Special Application settings from the "Current
Trigger-Port Table", select the Port Triggering settings you want to remove
in the table and then click <Delete Selected>. If you want remove all Port
Triggering settings from the table, just click the <Delete All> button. Click
<Reset> will clear your current selections.
- Application Layer Gateway (ALG)
You can select applications that need ALG support. The router will let the selected
application to correctly pass through the NAT gateway.
70
- UPNP
With UPnP, all PCs in you Intranet will discover this router automatically. So, you
don’t have to configure your PC and it can easily access the Internet through this
router.
71
Enable / Disable UPnP: You can enable or Disable the UPnP feature here.
After you enabled the UPnP feature, all client systems
that support UPnP, like Windows XP, can discover this
router automatically and access the Internet through this
router without having to configure anything. The NAT
Traversal
function
provided
by
UPnP
can
let
applications that support UPnP connect to the internet
without having to configure the virtual server sections.
- Quality of Service (QoS)
QoS can let you classify Internet application traffic by source/destination IP
address and port number. You can assign priority for each type of application
and reserve bandwidth for it. The packets of applications with higher priority will
always go first. Lower priority applications will get bandwidth after higher priority
applications get enough bandwidth. This can let you have a better experience in
using critical real time services like Internet phone, video conference …etc. All
the applications not specified by you are classified as rule “Others”.
Priority Queue
This can put the packets of specific protocols in High/Low Queue. The packets in
High Queue will process first.
72
Unlimited Priority Queue: The LAN IP address will not be bounded in the QoS
limitation.
High/Low Priority Queue: This can put the packets in the protocol and port
range to High/Low QoS Queue.
Bandwidth Allocation:
This can reserve / limit the throughput of specific protocols and port range. You
can set the upper bound and Lower bound.
73
Type: Specify the direction of packets. Upload / Download or both.
IP range: Specify the IP address range. You could also fill one IP address
Protocol: Specify the packet type. The default ALL will put all packets in the QoS
priority Queue.
Port range: Specify the Port range. You could also fill one Port.
Policy: Specify the policy of QoS, Min option will reserve the selected data rate
in QoS queue. Max option will limit the selected data rate in QoS queue.
Rate: The data rate of QoS queue.
Disabled: This turn off QoS Service.
74
- Routing
You can set Enable Static Routing to let the router forward packets using your routing
policy.
Destination LAN IP: Specify the destination LAN IP address of static routing rule.
75
Subnet Mask: Specify the Subnet Mask of static routing rule.
Default Gateway: Specify the default gateway of static routing rule.
Hops: Specify the Max Hops number of static routing rule.
Interface: Specify the Interface of static routing rule.
„ TOOLS
- Admin
You can change the password required to log into the broadband router's system
web-based management. By default, the password is: admin. Passwords can
contain 0 to 12 alphanumeric characters, and are case sensitive.
Old Password: Fill in the current password to allow changing to a new
password.
New Password: Enter your new password and type it again in Repeat New
Password for verification purposes
76
Remote management
Allows you to designate a host in the Internet. The ability to configure the
Broadband router from a remote site. Enter the designated host IP Address
in the Host IP Address field.
Host Address: This is the IP address of the host in the Internet that will have
management/configuration access to the Broadband router from
a remote site. If the Host Address is left 0.0.0.0 this means
anyone can access the router’s web-based configuration from a
remote location, providing they know the password.
Port: The port number of the remote management web interface.
Enabled: Check to enable the remote management function.
Click <Apply> at the bottom of the screen to save the above configurations.
- Time
The Time Zone allows your router to refer or base its time on the settings
configured here, which will affect functions such as Log entries and Firewall
settings.
Setting Up Time:
Synchronize with the NTP server
77
Time Zone: Select the time zone of the country you are currently located. The
router will set its time based on your selection.
NTP Time Server: The router can be set up to use external NTP Time Server.
Daylight Savings: The router can also be set to automatically adjust to the
Daylight Savings changes. If you wish to use this function,
you must select the Daylight Savings Time period and put a
checkmark on the Enable box to enable your daylight
savings time configuration.
Click <Apply> at the bottom of the screen to save the above configurations.
Synchronize with your PC
You could synchronize timer with your computers time.
78
PC Date and Time: This field would display your computer’s date and time.
Daylight Savings: The router can also take Daylight Savings into account. If you
wish to use this function, you must select the Daylight
Savings Time period and check/tick the enable box to enable
your daylight saving configuration.
Click <Apply> at the bottom of the screen to save the above configurations.
- DDNS
DDNS allows you to map the static domain name to a dynamic IP address. You
must register to a DDNS services and to get an account, password and your
static domain name from the DDNS service providers. This router supports
DynDNS, TZO and other common DDNS service providers.
79
Enable/Disable DDNS: Enable or disable the DDNS function of this router
Server Address: Select a DDNS service provider
Host Name: Fill in your static domain name that uses DDNS.
Username: The account that your DDNS service provider assigned to you.
Password: The password you set for the DDNS service account above.
Click <Apply> at the bottom of the screen to save the above configurations.
- Power
Saving power in WLAN mode can be enabled / disabled in this page.
80
- Diagnosis
In this page lets you run diagnosis to your network status.
- Firmware
This page allows you to upgrade the router’s firmware. To upgrade the firmware
of your Broadband router, you need to download the firmware file to your local
hard disk, and enter that file name and path in the appropriate field on this page.
You can also use the Browse button to find the firmware file in your PC.
81
Once you’ve selected the new firmware file, click <Apply> at the bottom of the
screen to start the upgrade process
- Back-up
This page allows you to save the current router configurations. When you save the
configurations, you also can restore the saved configurations into the router through
the Restore Settings. If extreme problems occur you can use the Restore to
Factory Defaults to set all configurations to its original default settings. Warning:
You will loose any saved data and settings when you set back to the manufacturer’s
default settings, but you can re-enter your previous settings manually.
82
Backup Settings: This can save the current Broadband router configuration to a file
named "config.bin" on your PC. You can also use the <Upload> button to restore
the saved configuration to the Broadband router. Alternatively, you can use the
"Restore to Factory Defaults" tool to force the Broadband router to perform a
power reset and restore the original factory settings.
- Reset
You can reset the broadband router when system stops responding correctly or stop
functions.
83
XIII - Repeater Mode
Repeater mode has limited settings compared to the AP mode. Choose “Repeater
mode” on the top right corner of the configuration page.
System restarts and connects to the IP address http://192.168..0.1
You will see the configuration homepage under “REPEATER” mode now.
„ System
- Status
System status section allows you to monitor the current status of your router.
You can see the Uptime, hardware information, serial number as well as firmware
version information.
84
LAN Settings: This page displays the Broadband router LAN port’s current LAN
information.
WLAN
Settings:
Wireless
configuration
details
such
as
SSID,
Status(Connected/Disconnected), Security and Channel are briefly shown.
- LAN
The LAN Tabs shows LAN settings. LAN settings can be change as needed. If you
are an entry level user, try opening a website from your computer. If you’re
successful and able to connect and browse the web site you opened without any
problem, do not change any of the settings.
Click <Apply> at the bottom of this screen to save the changed configurations.
IP address: This is the router’s LAN IP address (Your LAN clients default gateway
IP address). It can be changed based on your network architecture.
IP Subnet Mask: Specify a Subnet Mask IP address for your LAN segment.
85
802.1d Spanning Tree: This is disabled by default. If 802.1d Spanning Tree
function is enabled, this router will use the spanning
tree protocol to prevent network loops.
86
- Event Log
View operations log of the ENHWI-N3. This page shows the current system log
of the ENHWI-N3 router. It displays any event occurred after system start up.
Use the scroll bar to go down to the bottom of the page, the system log can be
saved <Save> to a local file for future use or the system log can be cleared
<Clear> or it can be refreshed <Refresh> to get the most updated information.
When the system is powered down, the system log will disappear if not saved to
a local file.
- Monitor
The Monitor Tab shows the bandwidth monitoring feature of each network
interface of the ENHWI-N3 router, wireless or wired and of the network packet
histogram for the network connection on WLAN. Auto refresh keeps information
updated frequently.
87
- Language
This Wireless Router supports multiple languages for user interface. Select your
preferred language.
„ Wireless
- Basic
You can set parameters use by the wireless stations to connect to this router. The
parameter includes Mode, ESSID, Channel Number and Associated Client.
88
Radio: Enable or Disable Wireless function
Band: Allows you to set the frequency band of the router. Fix at 802.11b,
802.11g or 802.11n modes. You can also select B+G mode to allow
802.11b and 802.11g clients at the same time.
Enable ESSID: You can specify the maximum ESSID number.
ESSID1~3: Allow you to specify ESSID of WLAN.
Site Survey: Click this button to scan the available wireless routers that can be
set as this router’s parent router. By doing so this ENHWI-N3 router will
become a wireless extender / repeater of the selected parent router. Select
one router from the list for that router to become this router’s parent router.
89
- Client List
This WLAN Client Table shows the Wireless client associated to this Wireless
Router.
- Policy
The Broadband router allows you to set up the Wireless Access Policy. If multiple
SSID is created, this is the place to set the policy for each SSID.
Communication between Wireless clients:
This function is to allow other Wireless Client to communicate with another Wireless
Client on the LAN connected on the same SSID.
90
Communication between Wireless clients and wired clients:
This function allows the Wireless Client to communicate with other Wireless Client in
the LAN on specific SSID as well as the Wired Client connected to the switch portion
of this router.
„ Tools
- Admin
You can change the password that is required to log into the broadband router's
system web-based management. By default, the password is: admin. Passwords
can contain 0 to 12 alphanumeric characters, and are case sensitive.
91
Old Password: Fill-in the current password to be replaced. This is required to
allow changing to a new password.
New Password: Enter your new password and again in Repeat New Password
for verification purpose
Click <Apply> at the bottom of the screen to save the above configurations
- Time
The Time Zone allows your router to use external source to time
synchronizations. This affects other functions such as Event Log entries and
Schedule settings that use time to do its tasks.
How to Set up Time:
Synchronize with the NTP server
Time Zone: Select the time zone of the country you are located. The router
will set its time based on your selection.
92
NTP Time Server: Enter the NTP Time Server address or URL here. This
also accepts local the IP address if the NTP Time
Server is on the same LAN.
Daylight Savings: The router can also setup to automatically adjust the
Daylight Savings Time changes each time DST
changes. To use this feature, click to put a checkmark
on the Enable box then enter the dates the DST would
starts and ends.
Click <Apply> at the bottom of the screen to save the above configurations
Synchronize and use your computer’s clock
The ENHWI-N3 can be synchronized the time to your computer’s time.
PC Date and Time: This field would display the user computers date and time.
Daylight Savings: The router can also setup to automatically adjust the Daylight
Savings Time changes each time DST changes. To use this
feature, click to put a checkmark on the Enable box then enter
the dates the DST would starts and ends.
Click <Apply> at the bottom of the screen to save the above configurations.
93
- Diagnosis
This page lets you diagnose the connection problem and the network status by
executing the Ping function. The result tells you whether the connection is broken or
successful.
- Firmware
This page allows you to upgrade the router’s firmware. To upgrade the firmware of
your Broadband router, you need to download the firmware file to your local hard
disk, and enter that file name and path in the appropriate field on this page. You can
also use the Browse button to find the firmware file on your PC.
Once you’ve selected the new firmware file, click <Apply> at the bottom of the
screen to start the upgrade process. Warning: Once the loading of the new
firmware started, do not power down the router.
- Back-up
The page allows you to save (Backup) the router’s current configuration settings.
94
The saved backup can be restored again if needed by sing the Restore
Settings selection and browse the saved backup file to restore back to the
expected settings. If restore is not an option the Restore to Factory Default may
be the only way to recover the router from damage. Using Restore to Factory
Default will reset all configurations and settings to its original factory default
settings (e.g. when you first purchased the router).
Backup Settings: Use this function to save the router’s current settings and
configuration to a file named "config.bin" to your computer.
You can also use the <Upload> button to restore the saved
configuration to the router. Alternatively, you can use the
"Restore to Factory Defaults" to force the Broadband
router to perform a power reset and restore the original
factory settings.
95
- Reset
You can software reset the broadband router when system stops responding or
stop working. This is different from the hardware reset that can reset the settings
by physically pressing the button.
Appendix A – FCC Interference Statement
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
z
Reorient or relocate the receiving antenna.
z
Increase the separation between the equipment and receiver.
96
z
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
z
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
We declare that the product is limited in CH1~CH11 by specified firmware controlled in the USA.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Appendix B – IC Interference Statement
Industry Canada statement:
This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
This device has been designed to operate with an antenna having a maximum gain of 2 dBi. Antenna
having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna
impedance is 50 ohms.
97
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement