MB 1000 L
.
MB 1000 H
Neodymium Dynamic
Cardioid Microphones
Description
The MB 1000 is a wide-range moving coil dynamic mic with a cardioid pickup pattern. It features a high-output neodymium magnet for maximum performance with all equipment.
The MB 1000 is designed specifically for close-up vocal and instrumental use. A special internal shock mount system minimizes handling and case noise. The microphone also features the MagnaLock ™ on/off switch for silent operation. The switch may be locked in the “on” position to prevent accidental turnoff during use.
The cardioid pickup pattern of the MB 1000 is useful in reducing unwanted background noise and controlling feedback, especially when used extremely close. Miking instruments or vocalists at very close range also effectively reduces “leakage” from one performer to the next. Low-frequency noise is also reduced by a low-frequency roll-off of sounds more than one foot distant from the microphone.
The high-output neodymium design and low-mass diaphragm and voice coil assure excellent signal-to-noise ratios with microphone mixers, tape recorders, and other electronic inputs. The
MB 1000 is capable of undistorted output even in very intense sound fields.
Enclosed in a rugged die-cast housing, the MB 1000 features a special, baked-on “Midnight Blues” finish. In addition to being attractive and comfortable to hold, this special finish further reduces handling noise and increases durability.
A multi-stage windscreen reduces wind noise and “popping” when performers work extremely close. The included microphone clamp permits mounting on any microphone stand with 5 /
8
"-27 threads.
Operation and Maintenance
The MB 1000 is available in low- and high-impedance versions.
In both versions, the 3-pin microphone output connector mates with XLRF-type cable connectors.
In the low-impedance MB 1000 L , the Lo-Z balanced signal appears across Pins 2 and 3, while the ground (shield) connection is Pin 1. Output is phased so that positive acoustic pressure produces positive voltage at Pin 2 in accordance with industry convention.
In the high-impedance MB 1000 H , the Hi-Z unbalanced output requires the use of a cable with XLRF-type to 1 /
4
" phone plug connectors. Pin 2 connection is to the 1 /
4
" phone plug tip, and
Pins 3 and 1 connect to ground. As with all high-impedance microphones, the use of cables longer than 20' is not recommended, since the added cable capacitance will create unacceptable high frequency losses and greater possibility of hum and noise pickup.
These Midnight Blues microphones utilize a MagnaLock on/off switch. This specially-designed switch operates silently and may be locked in the “on” position to prevent accidental turnoff during use. To lock, slide the switch up into the “on” position
(Fig. 1a). Using a small flathead screwdriver, rotate the small screw in the center of the switch 90 degrees ( 1 /
4 turn) counterclockwise (Fig. 1b). Never force the screw. When the screw slot position is horizontal (“across” the microphone body), the switch is locked. To unlock the switch, turn the screw 90 degrees clockwise until the screw slot position is again vertical (in line with the microphone body). Never try to turn the switch more than 90 degrees or 1 /
4 rotation. The switch may only be locked in the “on” position. Do not try to turn the screw when the switch is in the “off” position.
Unlocked
Position
O N
Fig. 1a
Locked
Position
O N
Fig. 1b
Do not turn
Do not try to lock switch screw clockwise in the “off ” to lock position
O N
Fig.1c
OFF
Fig. 1d
While every effort has been made to provide an extremely rugged microphone, reasonable care should be taken to avoid abuse. The microphone can withstand a wide range of temperatures and humidity without damage. Take care to keep foreign particles from entering the windscreen. If the microphone is exposed to an environment with small iron or steel filings
(on a workbench, for example) these fine metal particles can accumulate on the diaphragm, reducing low-frequency response.
Excessive accumulation of dirt on the windscreen will reduce high-frequency response.
Midnight Blues
®
MB 1000 L MB 1000 H
SPECIFICATIONS
†
Element
Polar Pattern
Frequency Response
Open Circuit Sensitivity
Impedance
Switch
Weight (less clamp)
Dimensions
Output Connector
Accessory Furnished
Neodymium Dynamic
Cardioid (Unidirectional)
70-15,000 Hz
MB1000L: 3.5 mV (–49 dBV) at 1 Pa*
MB1000H: 12.5 mV (–38 dBV) at 1 Pa*
MB1000L: 500 ohms (Lo-Z)
MB1000H: 10,000 ohms (Hi-Z)
MagnaLock ™ on/off
MB1000L: 9.3 oz (264 grams)
MB1000H: 9.6 oz (272 grams)
6.75" (171.5 mm) long, 2.16" (54.9 mm) head diameter, 1.38" to .87" (35.0 mm to 22.0 mm) tapered body diameter
Integral 3-pin XLRM-type
Tapered slip-in stand clamp for
5 /
8
"-27 threaded stands
† In the interest of standards development, A.T.U.S.
offers full details on its test methods to other industry professionals on request.
* 1 Pascal = 10 dynes/cm 2 = 10 microbars = 94 dB SPL
300
Polar Pattern
0
30
330
60
Frequency Response
10 dB
OPTIONAL ACCESSORIES
MBC 15 H 15' 2- conductor, shielded, vinyl-jacketed cable with XLRF-type connector at microphone end, 1 /
4
" phone plug at equipment end.
MBC 15 L 15' 2- conductor, shielded, vinyl-jacketed cable with XLRF-type connector at microphone end, XLRM-type connector at equipment end.
AT 8114 foam windscreen (slip-on).
CP 8201 line matching transformer
(Lo-Z to 50,000 ohms).
AT 8202 adjustable in-line attenuator for use with balanced Lo-Z microphones.
AT 8312 2- conductor, shielded, vinyl-jacketed, broadcast-type cable with XLRF-type connector at microphone end, 1 /
4
" phone plug at equipment end.
Available in 10', 20' & 25' lengths.
AT 8314 2- conductor, shielded, vinyl-jacketed, broadcast-type cable with
XLRF-type connector at microphone end,
XLRM-type connector at equipment end.
Available in 10', 20', 25', 30', 50' & 100' lengths.
AT 8407 universal “clothes-pin” clamp fits both tapered and cylindrical microphones.
AT 8410a shock mount for boom or stand operation. Universal “clothes-pin” clamp fits tapered and cylindrical microphones.
AT 8415 low-profile shock mount for boom or stand operation.
270 90
50
LEGEND
100 200 500 1k
Frequency in Hertz
2k
12" or more on axis
5k 10k 20k
240
LEGEND
1 kHz
210 150
180
SCALE IS 5 DECIBELS PER DIVISION
120
XLRM-type Plug Wiring
Lo-Z Balanced
1 /
4
" Phone Plug Wiring
Lo-Z and Hi-Z Unbalanced
RED WIRE WHITE WIRE
TIP SLEEVE SHIELD
One-Year Limited Warranty
Audio -Technica microphones and accessories purchased in the U.S.A. are warranted for one year from date of purchase by Audio -Technica U.S., Inc. (A.T.U.S.) to be free of defects in materials and workmanship. In event of such defect, product will be repaired promptly without charge or, at our option, replaced with a new product of equal or superior value if delivered to A.T.U.S. or an authorized service center prepaid, together with the sales slip or other proof of purchase date. Prior approval from A.T.U.S.
is required for return. This warranty excludes defects due to normal wear, abuse, shipping damage, or failure to use product in accordance with instructions. This warranty is void in the event of unauthorized repair or modification.
For return approval and shipping information, contact the Service Department, Audio-Technica U.S., Inc., 1221
Commerce Drive, Stow, Ohio 44224.
Except to the extent precluded by applicable state law,
A.T.U.S. will have no liability for any consequential, incidental, or special damages; any warranty of merchantability or fitness for particular purpose expires when this warranty expires.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
Outside the U.S.A., please contact your local dealer for warranty details.
Audio-Techinca U.S., Inc., 1221 Commerce Drive, Stow, Ohio 44224
Audio-Technica Limited, Old Lane, Leeds LS11 8AG England
Form No. 0323-9401- 02 © 1996 Audio-Technica U.S., Inc. Printed in U.S.A.