PC CHIPS P53G (V1.0)
Motherboard User’s Guide
This publication, including photographs, illustrations and software, is under the
protection of international copyright laws, with all rights reserved. Neither this
user’s guide, nor any of the material contained herein, may be reproduced
without the express written consent of the manufacturer.
The information in this document is subject to change without notice. The
manufacturer makes no representations or warranties with respect to the
contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, the manufacturer reserves
the right to revise this publication and to make changes from time to time in the
content hereof without obligation of the manufacturer to notify any person of
such revision or changes.
Trademarks
IBM, VGA, and PS/2 are registered trademarks of International Business
Machines.
Intel, Pentium/II/III, Pentium 4, Celeron and MMX are registered trademarks of
Intel Corporation.
Microsoft, MS-DOS and Windows 2000/XP/Vista are registered trademarks of
Microsoft Corporation.
AMI is a trademark of American Megatrends Inc.
It has been acknowledged that other brands or product names in this manual are
trademarks or the properties of their respective owners.
Static Electricity Precautions
1. Don’t take this motherboard and components out of their original staticproof package until you are ready to install them.
2. While installing, please wear a grounded wrist strap if possible. If you
don’t have a wrist strap, discharge static electricity by touching the bare
metal of the system chassis.
3. Carefully hold this motherboard by its edges. Do not touch those
components unless it is absolutely necessary. Put this motherboard on
the top of static-protection package with component side facing up
while installing.
Pre-Installation Inspection
1. Inspect this motherboard whether there are any damages to components
and connectors on the board.
2. If you suspect this motherboard has been damaged, do not connect
power to the system. Contact your motherboard vendor about those
damages.
Copyright © 2007
All Rights Reserved
P53G Series, V1.0
August 2007
i
Motherboard User’s Guide
Table of Contents
Trademark ............................................................................................................ i
Static Electricity Precautions ......................................................................................... i
Pre-Installation Inspection ............................................................................................. i
Chapter 1: Introduction ..................................................................................... 1
Key Features .................................................................................................................... 1
Package Contents ........................................................................................................... 4
Chapter 2: Motherboard Installation .............................................................. 5
Motherboard Components ............................................................................................ 6
I/O Ports .......................................................................................................................... 7
Installing the Processor ................................................................................................. 8
Installing Memory Modules .......................................................................................... 9
Jumper Settings ............................................................................................................ 1 0
Install the Motherboard ............................................................................................... 1 2
Connecting Optional Devices ..................................................................................... 1 3
Install Other Devices .................................................................................................... 1 5
Expansion Slots ............................................................................................................ 1 8
Chapter 3: BIOS Setup Utility ....................................................................... 20
Introduction .................................................................................................................. 2 0
Running the Setup Utility ................................................... …………………………...20
Standard CMOS Setup Page ....................................................................................... 2 1
Advanced Setup Page .................................................................................................. 2 2
Advanced Chipset Setup Page .................................................................................... 2 4
Integrated Peripherals Page ....................................................................................... 2 5
Power Management Setup Page ................................................................................ 2 6
PCI/PnP Setup Page .................................................................................................... 2 8
PCI Health Status Page ............................................................................................... 2 8
Frequency/Voltage Control Page ............................................................................... 2 9
Load Default Settings ................................................................................................... 3 0
Supervisor Password Page .......................................................................................... 3 0
User Password Page .................................................................................................... 3 1
Save & Exit Setup ......................................................................................................... 3 1
Exit Without Saving ...................................................................................................... 3 1
Chapter 4: Software & Applications .............................................................. 32
Introduction .................................................................................................................. 3 2
Installing Support Software ........................................................................................ 3 2
Bundled Software Installation .................................................................................... 3 6
ii
Motherboard User’s Guide
Chapter 5: VIA VT8237 RAID Setup Guide .................................................. 37
VIA RAID Configuration ............................................................................................. 3 7
Installing RAID Software & Drivers ........................................................................... 4 5
Using VIA RAID Tool ................................................................................................... 4 7
Notice:
1
Owing to Microsoft’s certifying schedule is various to every supplier,
we might have some drivers not certified yet by Microsoft. Therefore, it
might happen under Windows XP that a dialogue box (shown as below)
pop out warning you this software has not passed Windows Logo
testing to verify its compatibility with Windows XP. Please rest assured
that our RD department has already tested and verified these drivers.
Just click the “Continue Anyway” button and go ahead the installation.
iii
Chapter 1: Introduction
Chapter 1 Introduction
This motherboard has a LGA775 socket for latest * Intel® CoreTM 2 Quad/
TM
Intel® Core 2 Duo/Pentium® 4/Celeron® D processors with HyperThreading Technology and Front-Side Bus (FSB) speeds up to 1066 MHz.
Hyper-Threading Technology, designed to take advantage of the multitasking
features, giving you the power to do more things at once.
It integrates the P4M900 CD Northbridge and VT8237S Southbridge that
supports the Serial ATA interface for high-performance and mainstream desktop
PCs; the built-in USB 2.0 providing higher bandwidth, implementing Universal
Serial Bus Specification Revision 2.0 and is compliant with UHCI 1.1 and
EHCI 1.0. It supports High Definition Audio Codec and provides Ultra
DMA 133/100/66 function. It has one PCI Expressx16, one PCI Expressx1 and
two 32-bit PCI slots. There is a full set of I/O ports including two PS/2 ports for
mouse and keyboard, οne serial port, one VGA port, one LAN port (optional),
four back-panel USB 2.0 ports and Audio jacks for microphone, line-in and lineout and onboard USB headers providing extra ports by connecting the Extended
USB Module to the motherboard.
It is a Micro ATX motherboard and has power connectors for an ATX power
supply.
“ * ” stands for this motherboard is ready to support Intel® CoreTM2 Quad
processor Q6700 (G0) and below.
Key Features
The key features of this motherboard include:
LGA775 Socket Processor
•
•
TM
Supports the latest * Intel® CoreTM 2 Quad/Intel® Core 2 Duo/
Pentium® 4/Celeron® D processors with Hyper-Threading Technology
Supports up to 1066 MHz Front-Side Bus
Note: Hyper-Threading technology enables the operating system into
thinking it’s hooked up to two processors, allowing two threads to be
run in parallel, both on separate ‘logical’ processors within the same
physical processor.
1
Motherboard User’s Guide
Chipset
There are P4M900 CD Northbridge and VT8237S in the chipsets in accordance
with an innovative and scalable architecture with proven reliability and performance.
•
•
•
•
•
•
•
•
High Performance Host Interface: Supports * Intel® CoreTM 2 Quad/
TM
Intel® Core 2 Duo/Pentium® 4/Celeron® D processor family with
FSB 1066 MHz
Hyper-Threading Technology
System Memory Controller Support: DDR2 SDRAM with up to
maximum memory of 4 GB.
PCI Express Graphics Interface Support: One PCI Express x16 port
PCI Bus Interface Support: PCI Revision 2.3 Specification at 33MHz
Integrade Serial ATA Host Controller: Independent DMA operation on
two ports with Data transfer rates up to 3.0 Gb/s
Intgrated IDE Controller: Ultra DMA-133/100/66 Bus Master EIDE
Controller
USB 2.0: Integrated USB 2.0 interface, supporting up to eight functional
ports
Memory Support
•
Two 240-pin DIMM sockets for DDR2 SDRAM memory modules
•
Supports DDR2 667/533/400 memory bus
•
Maximum installed memory is 4 GB
Expansion Slots
•
Two 32-bit PCI slots
•
One PCI Expressx16 slot
•
One PCI Expressx1 slot
Onboard IDE channels
•
One IDE Connector
•
Supports PIO (Programmable Input/Output) and DMA (Direct Memory
Access) modes
•
Supports IDE Ultra DMA bus mastering with transfer rates of 133/100/
66 MB/sec
Serial ATA
•
Two Serial ATA Connectors
•
Transfer rate exceeding best ATA (3.0 Gb/s) with scalability to higher
rates
•
Low pin count for both host and devices
2
Chapter 1: Introduction
Audio
•
•
•
•
•
5.1Channel High Definition Audio Codec
ADCs support 44.1k/48k/96k sample rate
High-quality analog differential CD input
Meet Microsoft WHQL/WLP 3.0x audio requirements
Direct Sound 3DTM compatible
LAN (Optional)
•
•
•
Supports 10 Mb/s and 100 Mb/s N-way Auto-negotiation operation
Single Chip 100Base-TX/10Base-T Physical Layer Solution
Half/Full Duplex capability
Onboard I/O Ports
•
Two PS/2 ports for mouse and keyboard
•
One serial port
•
One VGA port
•
One LAN port (optional)
•
Four back-panel USB2.0 ports
•
Audio jacks for microphone, line-in and line-out
BIOS Firmware
This motherboard uses AMI BIOS that enables users to configure many system
features including the following:
•
Power management
•
Wake-up alarms
•
CPU parameters and memory timing
•
CPU and memory timing
The firmware can also be used to set parameters for different processor clock
speeds.
Dimensions
•
Micro ATX form factor of 244 x 200 mm
Note: Hardware specifications and software items are subject to change
without notification.
3
Motherboard User’s Guide
Package Contents
Your motherboard package ships with the following items:
‰ The motherboard
‰ The User’s Guide
‰ One diskette drive ribbon cable (optional)
‰ One IDE drive ribbon cable
‰ The Software support CD
Optional Accessories
You can purchase the following optional accessories for this
motherboard.
‰ The Extended USB module
‰ The CNR v.90 56K Fax/Modem card
‰ The Serial ATA cable
‰ The Serial ATA power cable
Note: You can purchase your own optional accessories from the third party,
but please contact your local vendor on any issues of the specification
and compatibility.
4
Chapter 2: Motherboard Installation
Chapter 2 Motherboard Installation
To install this motherboard in a system, please follow these instructions in this
chapter:
‰ Identify the motherboard components
‰ Install a CPU
‰ Install one or more system memory modules
‰ Make sure all jumpers and switches are set correctly
‰ Install this motherboard in a system chassis (case)
‰ Connect any extension brackets or cables to headers/connectors on the
motherboard
‰ Install peripheral devices and make the appropriate connections to
headers/connectors on the motherboard
Note:
1.
2.
Before installing this motherboard, make sure jumper CLR_CMOS is
under Normal setting. See this chapter for information about locating
CLR_CMOS and the setting options.
Never connect power to the system during installation; otherwise, it
may damage the motherboard.
5
Motherboard User’s Guide
Motherboard Components
ITEM
LABEL
1
CPU Socket
COMPONENTS
®
®
®
2
CPU_FAN
Pentium 4/Celeron D CPUs
CPU cooling fan connector
3
DDRII1~2
240-pin DDR2 SDRAM slots
4
ATX1
Standard 24-pin ATX pow er connector
5
SATA1~2
Serial ATA connectors
6
BIOS_WP
BIOS flash protect jumper
7
IDE1
Primary IDE connector
8
SPK1
Speaker header
9
IR1
Infrared header
10
PANEL1
Front panel sw itch/LED header
11
CLR_CMOS
Clear CMOS jumper
12
USB3~4
14
Front Panel USB headers
USBPWR_F2 Front Panel USB Pow er Select Jumper
FDD
Floppy disk drive connector
15
CD_IN1
Analog audio input connector
16
F_AUDIO1
Front panel audio header
17
SPDIFO1
SPDIF out header
18
PCI1~2
32-bit add-on card slots
19
PCIEX1
PCI Express x1 slot
20
PCIEX16
13
23
PCI Express slot for graphics interface
USBPWR_R1 Real Panel USB PS/2 Pow er Select Jumper
SYS_FAN
System cooling fan connector
LPT1
Parallel port header
24
ATX_12V1
21
22
®
LGA775 socket for *Intel CoreTM2 Quad/Intel CoreTM2 Duo/
Auxiliary 4-pin pow er connector
6
Chapter 2: Motherboard Installation
I/O Ports
The illustration below shows a side view of the built-in I/O ports on the
motherboard.
PS/2 Mouse
Use the upper PS/2 port to connect a PS/2 pointing
device.
PS/2 Keyboard
Use the low er PS/2 port to connect a PS/2
keyboard.
COM1
Use the COM port to connect serial devices such
as mice or fax/modems. COM1 is identified by the
system as COM1.
VGA Port
Use the VGA port to connect VGA devices.
LAN Port (optional)
Connect an RJ-45 jack to the LAN port to connect
your computer to the Netw ork.
USB Ports
Use the USB ports to connect USB devices.
Audio Ports
Use these three audio jacks to connect audio
devices. The first jack is for stereo Line-In signal,
the second jack for stereo Line-Out signal, and the
third jack for Microphone.
7
Motherboard User’s Guide
Installing the Processor
This motherboard has a LGA775 socket for the latest * Intel® CoreTM 2 Quad/
TM
Intel® Core 2 Duo/Pentium® 4/Celeron® D processors. When choosing a
processor, consider the performance requirements of the system. Performance is
based on the processor design, the clock speed and system bus frequency of the
processor, and the quantity of internal cache memory and external cache
memory.
CPU Installation Procedure
Follow these instructions to install the CPU:
A. Read and follow the instructions
shown on the sticker on the CPU cap.
B. Unload the cap
• Use thumb & forefinger to hold the
lifting tab of the cap.
• Lift the cap up and remove the cap
completely from the socket.
C. Open the load plate
• Use thumb & forefinger to hold the
hook of the lever, pushing down and
pulling aside unlock it.
• Lift up the lever.
• Use thumb to open the load plate.
Be careful not to touch the contacts.
D. Install the CPU on the socket
• Orientate CPU package to the socket.
Make sure you match triangle marker
to pin 1 location.
8
Chapter 2: Motherboard Installation
E. Close the load plate
• Slightly push down the load plate onto
the tongue side, and hook the lever.
• CPU is locked completely.
F. Apply thermal grease on top of the CPU.
G. Fasten the cooling fan supporting base
onto the CPU socket on the motherboard.
H. Make sure the CPU fan is plugged to the CPU
fan connector. Please refer to the CPU cooling fan
user’s manual for mor detail installation procedure.
Note 1: To achieve better airflow rates and heat dissipation, we suggest that
you use a high quality fan with 3800 rpm at least. CPU fan and
heatsink installation procedures may vary with the type of CPU fan/
heatsink supplied. The form and size of fan/heatsink may also vary.
Note 2: The fan connector supports the CPU cooling fan of 1.1A~2.2A (26.4W
max.) at +12V.
Note 3: Do Not remove the CPU cap from the socket before installing a CPU.
Note 4: Return Material Authorization (RMA) requests will be accepted only if
the motherboard comes with the cap on the LGA775 socket.
Installing Memory Modules
This motherboard accommodates two 240-pin DIMM sockets (Dual Inline
Memory Module) for unbuffered DDR2 667/533/400 memory modules (Double
Data Rate SDRAM), and maximum 4 GB installed memory.
Over its predecessor, DDR-SDRAM, DDR2-SDRAM offers greater bandwith
and density in a smaller packahe along with a reduction in power consumption.
In addition, DDR2-SDRAM offers new features and functions that enable a
higher clock rate and data rate operations of 400 MHz, 533 MHz and 667 MHz.
DDR2 transfer 64 bits of data twice every clock cycle.
9
Motherboard User’s Guide
Memory Module Installation Procedure
These modules can be installed with up to 4 GB system memory. Refer to the
following to install the memory module.
1.
Push down the latches on both sides of the DIMM socket.
2.
Align the memory module with the socket. There is a notch on the
DIMM socket that you can install the DIMM module in the correct
direction. Match the cutout on the DIMM module with the notch on
the DIMM socket.
3.
Install the DIMM module into the socket and press it firmly down
until it is seated correctly. The socket latches are levered upwards and
latch on to the edges of the DIMM.
4.
Install any remaining DIMM modules.
Jumper Settings
Connecting two pins with a jumper cap is SHORT; removing a jumper cap from
these pins, OPEN.
10
Chapter 2: Motherboard Installation
CLR_CMOS: Clear CMOS Jumper
Use this jumper to clear the contents of the CMOS memory. You may need to
clear the CMOS memory if the settings in the Setup Utility are incorrect and
prevent your motherboard from operating. To clear the CMOS memory,
disconnect all the power cables from the motherboard and then move the jumper
cap into the CLEAR setting for a few seconds.
1
CLR_CMOS
Function
Jum per Setting
Normal
Short Pins 1-2
Clear CMOS Short Pins 2-3
Note: To avoid the system unstability after clearing CMOS, we recommend
users to enter the main BIOS setting page to “Load Optimal De-faults”
and then “Save Changes and Exit”.
BIOS_WP: BIOS FLASH PROTECT Jumper
Use this jumper to set the BIOS FLASH PROTECT function.
1
BIOS_WP
Function
Jum per Setting
WRITE ENABLE
OPEN
WRITE DISABLE
SHORT
USBPWR_F2: FRONT PANEL USB POWER SELECT Jumper
1
USBPWR_F2
Function
VCC
5VSB
Jum per Setting
Short Pins 1-2
Short Pins 2-3
USBPWR_R1: REAR USB PS/2 POWER SELECT Jumper
Use this jumper to set the Rear USB PS/2 Power function.
1
USBPWR_R1
Function
VCC
5VSB
Jum per Setting
Short Pins 1-2
Short Pins 2-3
Note: Make sure the power supply provides enough SB5V voltage before
selecting the SB5V function.
11
Motherboard User’s Guide
Install the Motherboard
Install the motherboard in a system chassis (case). The board is a Micro ATX
size motherboard. You can install this motherboard in an ATX case. Make sure
your case has an I/O cover plate matching the ports on this motherboard.
Install the motherboard in a case. Follow the case manufacturer’s instructions to
use the hardware and internal mounting points on the chassis.
Connect the power connector from the power supply to the ATX1 connector on
the motherboard. The ATX_12V1 is a +12V connector for CPU Vcore power.
If there is a cooling fan installed in the system chassis, connect the cable from the
cooling fan to the SYS_FAN fan power connector on the motherboard.
Connect the case switches and indicator LEDs to the PANEL1 header.
Here is a list of the PANEL1 pin assignments.
Pin
1
3
5
7
9
Signal
HD_LED_P(+)
HD_LED_N(-)
RESET_SW_N(-)
RESET_SW_P(+)
RSVD_DNU
Pin
2
4
6
8
10
12
Signal
FP PWR/SLP(+)
FP PWR/SLP(-)
POWER_SW_P(+)
POWER_SW_N(-)
KEY
Chapter 2: Motherboard Installation
Connecting Optional Devices
Refer to the following for information on connecting the motherboard’s optional
devices:
SPK1: Speaker Header
Connect the cable from the PC speaker to the SPK1 header on the motherboard.
Pin
1
3
Signal
VCC
NC
Pin
2
4
Signal
Key
Signal
SPDIFO1: S/PIF Out Header
S/PDIF (Sony/Plilips Digital Interface) is a standard audio transfer file format
and allows the transfer of digatal audio signals from one device to another
without having to be converted first to an analog format. Via a specific audio
cable, you can connect the SPDIFO1 header (S/PDIF output) on the
motherboard to the S/PDIF digital input on the external speakers or AC Decode
devices.
Pin
1
3
Signal
SPDIFOUT
KEY
Pin
2
4
13
Signal
5VA
GDN
Motherboard User’s Guide
F_AUDIO1: Front Panel Audio Header
This header allows the user to install auxiliary front-oriented microphone and
line-out ports for easier access.
Pin
1
3
5
7
9
Signal
PORT1L
PORT1R
PORT2R
SENSE_SEND
PORT2L
Pin
2
4
6
8
10
Signal
GND
PRESENCE#
Sense1_return
KEY
Sense2_return
USB3/USB4: Front panel USB Headers
The motherboard has USB ports installed on the rear edge I/O port array.
Additionally, some computer cases have USB ports at the front of the case. If
you have this kind of case, use auxiliary USB headers USB3/USB4 to connect
the front-mounted ports to the motherboard.
Pin
1
3
5
7
9
1.
2.
3.
Sig n al
V ERG_FP_USBPW R0
USB_FP_P0(-)
USB_FP_P0(+)
GROUND
KEY
Pin
2
4
6
8
10
Sig n a l
V ERG_ FP_USBPW R0
USB_FP_P1(- )
USB_FP_P1(+)
GROUND
NC
Locate the USB3/USB4 header on the motherboard.
Plug the bracket cable onto the USB3/USB4 header.
Remove a slot cover from one of the expansion slots on the system
chassis. Install an extension bracket in the opening. Secure the
extension bracket to the chassis with a screw.
IR1: Infrared Header
The infrared port allows the wireless exchange of information between your
computer and similarly equipped devices such as printers, laptops, Personal
Digital Assistants (PDAs), and other computers.
Pin
1
3
5
1.
2.
Signal Pin
NC
2
+5V
4
IRTX
6
Signal
KEY
GND
IRRX
Locate the infrared port-IR1 header on the motherboard.
If you are adding an infrared port, connect the ribbon cable from the
port to the IR1 header and then secure the port to an appropriate
place in your system chassis.
14
Chapter 2: Motherboard Installation
LPT1: Onboard parallel port Header
This header allows the user to connect to the printer, scanner or devices.
Pin
Signal
Pin
Signal
1
STROBE
2
PD0
3
PD1
4
PD2
5
PD3
6
PD4
7
PD5
8
PD6
9
PD7
10
ACK
11
BUSK
12
PE
13
SLCT
14
ALF
15
ERROR
16
INIT
17
SLCTIN
18
Ground
19
Ground
20
Ground
21
Ground
22
Ground
23
Ground
24
Ground
25
Ground
26
Key
Install Other Devices
Install and connect any other devices in the system following the steps below.
15
Motherboard User’s Guide
Floppy Disk Drive
The motherboard ships with a floppy disk drive cable that can support one or
two drives. Drives can be 3.5" or 5.25" wide, with capacities of 360 K, 720 K,
1.2 MB, 1.44 MB, or 2.88 MB.
Install your drives and connect power from the system power supply. Use the
cable provided to connect the drives to the floppy disk drive connector FDD1.
IDE Devices
IDE devices include hard disk drives, high-density diskette drives, and CD-ROM
or DVD-ROM drives, among others.
The motherboard ships with an IDE cable that can support one or two IDE
devices. If you connect two devices to a single cable, you must configure one of
the drives as Master and one of the drives as Slave. The documentation of the
IDE device will tell you how to configure the device as a Master or Slave device.
The Master device connects to the end of the cable.
Install the device(s) and connect power from the system power supply. Use the
cable provided to connect the device(s) to the Primary IDE channel connector
IDE1 on the motherboard.
Serial ATA Devices
The Serial ATA (Advanced Technology Attachment) is the standard interface for
the IDE hard drives, which is designed to overcome the design limitations while
enabling the storage interface to scale with the growing media rate demands of PC
platforms. It provides you a faster transfer rate of 3.0 Gb/s. If you have installed a
Serial ATA hard drive, you can connect the Serial ATA cables to the Serial ATA hard
drive or the connector on the motherboard.
On the motherboard, locate the Serial ATA connectors SATA1/2, which support
new Serial ATA devices for the highest data transfer rates, simpler disk drive cabling
and easier PC assembly.
It eliminates limitations of the current Parallel ATA interface, but maintains register
compatibility and software compatibility with Parallel ATA.
16
Chapter 2: Motherboard Installation
Analog Audio Input Connector
If you have installed a CD-ROM drive or DVD-ROM drive, you can connect
the drive audio cable to the onboard sound system.
When you first start up your system, the BIOS should automatically detect
your CD-ROM/DVD drive. If it doesn’t, enter the Setup Utility and configure
the CD-ROM/DVD drive that you have installed. On the motherboard, locate
the 4-pin connector CD_IN1.
Pin
1
2
3
Signal
CD IN L
GND
GND
4
CD IN R
17
Motherboard User’s Guide
Expansion Slots
This motherboard has one PCI Ex16, one PCI Ex1 and two 32-bit PCI slots.
18
Chapter 2: Motherboard Installation
Follow the steps below to install an PCI Express/CNR/PCI expansion card.
1
Locate the PCI Express, CNR or PCI slots on the motherboard.
2
Remove the blanking plate of the slot from the system chassis.
3
Install the edge connector of the expansion card into the slot. Ensure
the edge connector is correctly seated in the slot.
4
Secure the metal bracket of the card to the system chassis with a
screw.
PCI Express Slot
You can install an external PCI Express graphics card that is fully compliant to the
PCI Express Base Specification revsion 1.0a.
PCI Slots
You can install the 32-bit PCI interface expansion cards in the slots.
19
Motherboard User’s Guide
Chapter 3 BIOS Setup Utility
Introduction
The BIOS Setup Utility records settings and information of your computer, such
as date and time, the type of hardware installed, and various configuration
settings. Your computer applies the information to initialize all the components
when booting up and basic functions of coordination between system components.
If the Setup Utility configuration is incorrect, it may cause the system to
malfunction. It can even stop your computer booting properly. If it happens,
you can use the clear CMOS jumper to clear the CMOS memory which has
stored the configuration information; or you can hold down the Page Up key
while rebooting your computer. Holding down the Page Up key also clears the
setup information.
You can run the setup utility and manually change the configuration. You might
need to do this to configure some hardware installed in or connected to the
motherboard, such as the CPU, system memory, disk drives, etc.
Running the Setup Utility
Every time you start your computer, a message appears on the screen before the
operating system loading that prompts you to “Hit <DEL>if you want to run
SETUP”. Whenever you see this message, press the Delete key, and the Main
menu page of the Setup Utility appears on your monitor.
CMOS Setup Utility – Copyright (C) 1985-2005, American Megatrends, Inc
Standard CMOS Setup
Advanced Setup
Advanced Chipset Setup
Integrated Peripherals
Power Management Setup
PCI / PnP Setup
PC Health Status
Frequency/Voltage Control
Load Default Settings
Supervisor Password
User Password
Save & Exit Setup
Exit Without Saving
: Move Enter: Select +/-/: Value
F10: Save Esc: Exit
F1: General Help
F9: Optimized Defaults
V02.59 (C) Copyright 1985-2005, American Megatrends, Inc.
You can use cursor arrow keys to highlight anyone of options on the main menu
page. Press Enter to select the highlighted option. Press the Escape key to leave
the setup utility. Press +/-/ to modify the selected field’s values.
20
Chapter 3: BIOS Setup Utility
Some options on the main menu page lead to tables of items with installed values
that you can use cursor arrow keys to highlight one item, and press PgUp and
PgDn keys to cycle through alternative values of that item. The other options on
the main menu page lead to dialog boxes requiring your answer OK or Cancel by
selecting the [OK] or [Cancel] key.
If you have already changed the setup utility, press F10 to save those changes
and exit the utility. Press F1 to display a screen describing all key functions.
Press F9 to load optimtimal settings.
Standard CMOS Setup Page
This page displays a table of items defining basic information of your system.
CMOS Setup Utility – Copyright (C) 1985-2005, American Megatrends, Inc.
Standard CMOS Setup
Date
Time
Wed 07/18/2007
03:08:56
Primary IDE Master
Primary IDE Slave
S-ATA1
S-ATA2
Help Item
While entering setup, BIOS
auto detects the presence of
IDE devices. This displays
the status of auto detection of
IDE devices.
ATAPI CDROM
Not Detected
Hard Disk
Hard Disk
IDE BusMaster
Enabled
Drive A
1.44 MB 31/ 2
: Move Enter: Select +/-/: Value
F10: Save Esc: Exit
F1: General Help
F9: Optimized Defaults
Date & Time
These items set up system date and time.
Primary IDE Master/Primary IDE Slave
Use these items to configure devices connected to the Primary IDE channels. To
configure an IDE hard disk drive, choose Auto. If the Auto setting fails to find a
hard disk drive, set it to User, and then fill in the hard disk characteristics (Size,
Cyls, etc.) manually. If you have a CD-ROM drive, select the setting CDROM.
If you have an ATAPI device with removable media (e.g. a ZIP drive or an LS120), select Floptical.
S-ATA1/2
These items display the status of auto detection of saa devices when “Onboard
SATA-IDE” sets to “IDE”.
IDE BusMaster
This item enables or disables the DMA under DOS mode. We recommend you to
leave this item at the default value.
Drive A
The item defines the characteristics of any diskette drive attached to the system.
You can connect one or two diskette drives.
21
Motherboard User’s Guide
Advanced Setup Page
This page sets up more advanced information about your system. Handle this
page with caution. Any changes can affect the operation of your computer.
CMOS Setup Utility – Copyright (C) 1985-2005, American Megatrends, Inc.
Advanced Setup
TM Status
Limit CPUID MaxVal
Hyper-Threading Technology
Quick Power on Self Test
Bootup NumLock Status
APIC Mode
1st Boot Device
2nd Boot Device
3rd Boot Device
Hard Disk Drives
Removable Drives
CD/DVD Drives
Boot Other Device
BIOS Protect
TM1
Disabled
Enabled
Enabled
On
Enabled
1st FLOPPY DRIVE
ST3120023AS
DVD-ROM DDU1632
Press Enter
Press Enter
Press Enter
Yes
Disabled
Help Item
Disabled for WindowsXP
: Move Enter: Select +/-/: Value
F10: Save Esc: Exit
F1: General Help
F9: Optimized Defaults
TM Status
This item display CPU Thermal Monitor status.
Limit CPUID MaxVal
This item can support Prescott CPUs for old OS. Users please note that under
NT 4.0, it must be set “Enabled”, while under WinXP, it must be set “Disabled”
Hyper-Threading Technology
This item is only available when the chipset supports Hyper-Threading and you
areusing a Hyper-Threading CPU.
Quick Power On Self Test
Enable this item to shorten the power on self testing (POST) and have your
system start up faster. You might like to enable this item after you confident that
your system hardware is operating smoothly.
Boot Up NumLock Status
This item determines if the NumLock key is active or inactive at system start-up
time.
APIC Mode
This item allows you to enable or disable the APIC (Advanced Programmable
Interrupt Controller) mode. APIC provides symmetric multi-processing (SMP)
for systems, allowing support for up to 60 processors.
1st/2nd/3rd Boot Device
Use these items to determine the device order the computer uses to look for an
operating system to load at start-up time.
22
Chapter 3: BIOS Setup Utility
f Hard Disk Drives (Press Enter)
Scroll to this item and press <Enter> to view the following screen:
CMOS Setup Utility – Copyright (C) 1985-2005, American Megatrends, Inc.
Hard Disk Drives
Help Item
Hard Disk Drives
1st FLOPPY DRIVE
WDC WD2500JS-08NCB1
1st Drive
2nd Drive
Specifies the boot
sequence from the
available devices.
: Move Enter: Select +/-/: Value
F10: Save Esc: Exit
F1: General Help
F9: Optimized Defaults
Press <Esc> to return to Advanced Setup screen.
f Removable Drives (Press Enter)
Scroll to this item and press <Enter> to view the following screen:
CMOS Setup Utility – Copyright (C) 1985-2005, American Megatrends, Inc.
Removable Drives
Help Item
Removable Drives
1st FLOPPY DRIVE
1st Drive
Specifies the boot
sequence from the
available devices.
: Move Enter: Select +/-/: Value
F10: Save Esc: Exit
F1: General Help
F9: Optimized Defaults
Press <Esc> to return to Advanced Setup screen.
f CD/DVD Drives (Press Enter)
Scroll to this item and press <Enter> to view the following screen:
CMOS Setup Utility – Copyright (C) 1985-2005, American Megatrends, Inc.
CD/DVD Drives
Help Item
CD-DVD Drives
1st Drive
DVD-ROM DDU1632
Specifies the boot
sequence from the
available devices.
: Move Enter: Select +/-/: Value
F10: Save Esc: Exit
F1: General Help
F9: Optimized Defaults
Press <Esc> to return to Advanced Setup screen.
23
Motherboard User’s Guide
Boot Other Device
When enabled, the system searches all other possible locations for operating
system if it fails to find one in the devices specified under the First, Second, and
Third boot devices.
BIOS Protect
This item enables or disables BIOS protect.
Press <Esc> to return to the main menu page.
Advanced Chipset Setup Page
This page sets up more advanced chipset information about your system.
Handle this page with caution. Any changes can affect the operation of your
computer.
CMOS Setup Utility – Copyright (C) 1985-2005, American Megatrends, Inc.
Advanced Chipset Setup
DRAM Timing
VGA Share Memory Size
Help Item
Auto
256MB
Options
Manual
Auto
Turbo
Ultra
: Move Enter: Select +/-/: Value
F10: Save Esc: Exit
F1: General Help
F9: Optimized Defaults
DRAM Timing
This item allows you to enable or disable the DRAM timing defined by the Serial
Presence Detect electrical. Users please note that if setting this item to auto, the
following two items are not available.
VGA Share Memory Size
This item shows the VGA memory size borrowed from main memory capability.
In this case, 256MB is borrowed, which in the meanwhile the same the main
memory loses.
Press <Esc> to return to the main menu page.
24
Chapter 3: BIOS Setup Utility
Integrated Peripherals Page
This page sets up some parameters for peripheral devices connected to the
system.
CMOS Setup Utility – Copyright (C) 1985-2005, American Megatrends, Inc.
Integrated Peripherals
OnBoard Floppy Controller
Serial Port1 Address
Serial Port2 Adress
Serial Port2 Mode
Parallel Port Address
Parallel Port Mode
ECP Mode DMA Channel
Parallel Port IRQ
SATA Controller
HDAC Audio Controller
LAN Controller
LAN Option ROM
OnBoard USB Function
USB Function For DOS
Enabled
3F8/IRQ4
2F8/IRQ3
Normal
378
ECP
DMA3
IRQ7
IDE
Auto
Enabled
Disabled
Enabled
Enabled
Help Item
Allow BIOS to Enable
or Disable Floppy
Controller.
: Move Enter: Select +/-/: Value
F10: Save Esc: Exit
F1: General Help
F9: Optimized Defaults
OnBoard Floppy Controller
Use this item to enable or disable the onboard floppy disk drive interface.
Serial Port1/2 Address
Use this item to enable or disable the onboard COM1 serial port, and to assign a
port address.
Serial Port2 Mode
If Serial Port 2 Address is not disabled, it allows you to set the Serial Port 2 Mode.
Parallel Port Address
Use this item to enable or disable the onboard Parallel port, and to assign a port
address.
Parallel Port Mode
Use this item to select the parallel port mode. You can select Normal (Standard
Parallel Port), ECP (Extended Capabilities Port), EPP (Enhanced Parallel Port),
or BPP (Bi-Directional Parallel Port).
ECP Mode DMA Channel
Use this item to assign the DMA Channel under ECP Mode function.
Parallel Port IRQ
Use this item to assign IRQ to the parallel port.
SATA Controller
Use this item to enable or disable the onboard SATA controller.
25
Motherboard User’s Guide
HDAC Audio Controller
Use this item to enable or disable the onboard Audio controller.
LAN Controller
This option allows you to enable or disable the onboard LAN controller.
LAN Option ROM
Use this item to enable or disable the booting from the onboard LAN with a
remote boot ROM installed.
Onboard USB Function
Enable this item if you plan to use the USB ports on this motherboard.
USB Function For DOS
Enable this item if you plan to use the USB ports on this motherboard in a DOS
environment.
Press <Esc> to return to the main menu setting page.
Power Management Setup Page
This page sets some parameters for system power management operation.
CMOS Setup Utility – Copyright (C) 1985-2005, American Megatrends, Inc.
Power Management Setup
ACPI Suspend Type
Suspend Time Out
Resume on RTC Alarm
Resume On Ring
Resume On PME#
Resume by WOL
Resume On PS/2 Mouse
Resume by PCI-E PME
PWRON After PWR-Fail
Soft-Off by PWR-BTTN
USB Device Wakeup Function
Resume On KBC
Wake-Up Key
S1
Disabled
Disabled
Disabled
Enabled
Disabled
Disabled
Disabled
Power Off
Instant Off
Enabled
Disabled
Any Key
Help Item
Select the ACPI
state used for
System Suspend.
: Move Enter: Select +/-/: Value
F10: Save Esc: Exit
F1: General Help
F9: Optimized Defaults
ACPI Suspend Type
Use this item to define how your system suspends. In the default, S3 (STR), the
suspend mode is a suspend to RAM, i.e., the system shuts down with the
exception of a refresh current to the system memory.
Suspend Time Out
This item sets up the timeout for Suspend mode in minutes. If the time selected
passes without any system activity, the computer will enter power-saving Suspend mode.
26
Chapter 3: BIOS Setup Utility
Resume On RTC Alarm
The system can be turned off with a software command. If you enable this item,
the system can automatically resume at a fixed time based on the system’s RTC
(realtime clock). Use the items below this one to set the date and time of the
wake-up alarm. You must use an ATX power supply in order to use this feature.
Resume On Ring
The system can be turned off with a software command. If you enable this item,
the system can automatically resume if there is an incoming call on the Modem.
You must use an ATX power supply in order to use this feature.
Resume On PME#
The system can be turned off with a software command. If you enable this item,
the system can automatically resume if there is an incoming call on the PCI
Modem or PCI LAN card. You must use an ATX power supply in order to use
this feature. Use this item to do wake-up action if inserting the PCI card.
Resume by WOL
This item specifies whether the system will be awakened from power saving
modes when activity or input signal of the specified WOL device is detected.
Resume On PS/2 Mouse
This item enables or disables you to allow mouse activity to awaken the system
from power saving mode.
Resume by PCI-E PME
This item specifies whether the system will be awakened from power saving
modes when activity or input signal of the specified WOL device is detected.
PWRON After PWR-Fail
This item enables your computer to automatically restart or return to its last
operating status.
Soft-Off By PWR- BTTN
If the item is set to Instant-Off, then the power button causes a software power
down. If the item is set to Delay 4 Sec. then you have to hold the power button
down for four seconds to cause power down.
USB Device Wakeup Function
This item allows you to enable or disable the USB device Wakeup function.
Resume On KBC
This item enables or disables you to allow keyboard activity to awaken the
system.
•
Wake-Up key: When Keyboard Power On is set to Enable, this item is
available and users can enter any key, or hot key on the keyboard or
type in the password.
Press <Esc> to return to the main menu setting page.
27
Motherboard User’s Guide
PCI / PnP Setup Page
This page sets up some parameters for devices installed on the PCI bus and
those utilizing the system plug and play capability.
CMOS Setup Utility – Copyright (C) 1985-2005, American Megatrends, Inc.
PCI / PnP Setup
Init Display First
Allocate IRQ to PCI VGA
PCI
Yes
Help Item
Options
PCI
PCI Express Card
: Move Enter: Select +/-/: Value
F10: Save Esc: Exit
F1: General Help
F9: Optimized Defaults
Init Dispaly First
This item allows you to choose the primary display card.
Allocate IRQ to PCI VGA
If this item is enabled, an IRQ will be assigned to the PCI VGA graphics system.
You set this value to No to free up an IRQ.
PCI Health Status Page
This page helps you monitor the parameters for critical voltages, temperatures
and fan speeds.
CMOS Setup Utility – Copyright (C) 1985-2005, American Megatrends, Inc.
PC Health Status
Hardware Health Event Monitoring
Vcore
: 1.296V
Vdimm
: 1.592V
Vcc5V
: 1.296V
CPU FAN Speed
: 1962RPM
CPU Temperature
: 162°C/143°F
CPU SMART Fan Control
Disabled
Help Item
Options
Disabled
Enabled
: Move Enter: Select +/-/: Value
F10: Save Esc: Exit
F1: General Help
F9: Optimized Defaults
28
Chapter 3: BIOS Setup Utility
System Component Characteristics
These fields provide you with information about the system current operating
status.
•
•
•
•
•
•
CPU Temperature
System Temperature
CPU Fan Speed
System Fan Speed
CPU Vorce
VDIMM
CPU SMART Fan Control
This item allows users to enable or disable smart fan control function.
Press <Esc> to return to the main menu setting page.
Frequency/Voltage Control Page
This page helps you to set the clock speed and system bus for your system. The
clock speed and system bus are determined by the kind of processor you have
installed in your system.
CMOS Setup Utility – Copyright (C) 1985-2005, American Megatrends, Inc.
Frequncey/Voltage Control
Manufacturer : Intel
Ratio Actual Value : 15
DRAM Frequency
CPU Over-clocking Func.:
CPU Frequency
:
Auto Detect DIMM/PCI Clk
Spread Spectrum
Help Item
Auto
Disabled
200MHz
Enabled
Enabled
Options
Auto
400MHz
533 MHz
667 MHz
: Move Enter: Select +/-/: Value
F10: Save Esc: Exit
F1: General Help
F9: Optimized Defaults
Manufacturer
This item indicates the brand of the CPU installed in your system.
Ratio Actual Value
This item determinese the actual value of ratio.
DRAM Frequency
This item enables users to adjust the DRAM frequency. The default setting is
auto and we recommend users leave the setting unchanged. Modify it at will may
cause the system to be unstable.
29
Motherboard User’s Guide
CPU Over-clocking Func.
This item decides the CPU over-clocking function/frequencyinstalled in your
system. If the over-clocking fails, please turn offthe system power. And then,
hold the PageUp key (similar to theClear CMOS function) and turn on the power,
the BIOS willrecover the safe default.
CPU Frequency
This item indicates the current CPU frequency. Users can not make any change to
this item. Please noted that the frequency will be varied with different CPU.
Auto Detect DIMM/PCI Clk
When this item is enabled, BIOS will disable the clock signal of free DIMM/PCI
slots.
Spread Spectrum
If you enable spread spectrum, it can significantly reduce the EMI (ElectroMagnetic interface) generated by the system.
Load Default Settings
This option opens a dialog box to ask if you are sure to install optimized
defaults or not. You select [OK], and then <Enter>, the Setup Utility loads all
default values; or select [Cancel], and then <Enter>, the Setup Utility does not
load default values.
Note: It is highly recommend that users enter this option to load optimal default
values for accessing the best performance.
Supervisor Password Page
This page helps you set up some parameters for the hardware monitoring
function of this motherboard.
CMOS Setup Utility – Copyright (C) 1985-2005, American Megatrends, Inc.
Supervisor Password
Supervisor Password : Not Installed
Change Supervisor Password
Help Item
Press Enter
Installed or Change the
password
: Move Enter: Select +/-/: Value
F10: Save Esc: Exit
F1: General Help
F9: Optimized Defaults
Supervisor Password
This item indicates whether a supervisor password has been set. If the password
has been installed , Installed displays. If not, Not Installed dispalys.
30
Chapter 3: BIOS Setup Utility
Change Supervisor Password
You can select this option and press<Enter> to access the sub menu. You can use
the sub menu to change the supervisor password.
Press <Esc> to return to the main menu setting page.
User Password Page
This page helps you set up some parameters for the hardware monitoring
function of this motherboard.
CMOS Setup Utility – Copyright (C) 1985-2005, American Megatrends, Inc.
User Password
User Password : Not Installed
Change User Password
Help Item
Press Enter
Installed or Change the
password
: Move Enter: Select +/-/: Value
F10: Save Esc: Exit
F1: General Help
F9: Optimized Defaults
User Password
This item indicates whether a user password has been set. If the password has
been installed , Installed displays. If not, Not Installed dispalys.
Change User Password
You can select this option and press<Enter> to access the sub menu. You can use
the sub menu to change the supervisor password.
Save & Exit Setup
Highlight this item and press <Enter> to save the changes that you have made in
the Setup Utility and exit the Setup Utility. When the Save and Exit dialog box
appears, press [Y] to save and exit, or press [N] to return to the main menu.
Exit Without Saving
Highlight this item and press <Enter> to discard any changes that you have made
in the Setup Utility and exit the Setup Utility. When the Exit Without Saving
dialog box appears, press [Y] to discard changes and exit, or press [N] to return
to the main menu.
Note: If you have made settings that you do not want to save, use the “Exit
Without Saving” item and presst [Y] to discard any changes you have
made.
31
Motherboard User’s Guide
Chapter 4 Software & Applications
Introduction
This chapter describes the contents of the support CD-ROM that comes with the
motherboard package.
The support CD-ROM contains all useful software, necessary drivers and utility
programs to properly run our products. More program information is available in
a README file, located in the same directory as the software.
To run the support CD, simply insert the CD into your CD-ROM drive. An Auto
Setup screen automatically pops out, and then you can go on the auto-installing or
manual installation depending on your operating system.
If your operating system is Windows 2000/XP/Vista, it will automatically install
all the drivers and utilities for your motherboard.
Installing Support Software
1
2
3
Insert the support CD-ROM disc in the CD-ROM drive.
When you insert the CD-ROM disc in the system CD-ROM drive,
the CD automatically displays an Auto Setup screen.
The screen displays three buttons of Setup, Browse CD and Exit on
the right side, and three others Setup, Application and ReadMe at
the bottom. Please see the following illustration.
The Setup button runs the software auto-installing program as explained in next
section.
The Browse CD button is a standard Windows command that you can check the
contents of the disc with the Windows file browsing interface.
32
Chapter 4: Software & Applications
The Exit button closes the Auto Setup window. To run the program again, reinsert
the CD-ROM disc in the drive; or click the CD-ROM driver from the Windows
Explorer, and click the Setup icon.
The Application button brings up a software menu. It shows the bundled software
that this mainboard supports.
The ReadMe brings you to the Install Path where you can find out path names of
software driver.
Auto-Installing under Windows 2000/XP/Vista
If you are under Windows 2000/XP, please click the Setup button to run the
software auto-installing program while the Auto Setup screen pops out after
inserting the support CD-ROM:
1
The installation program loads and displays the following screen.
Click the Next button.
2
Select the items that you want to setup by clicking on it (the default
options are recommended). Click the Next button to proceed.
33
Motherboard User’s Guide
3
The support software will automatically install.
Once any of the installation procedures start, software is automatically installed in
sequence. You need to follow the onscreen instructions, confirm commands and
allow the computer to restart as few times as needed to complete installing whatever software you selected. When the process is finished, all the support software
will be installed and start working.
During the Windows Vista Driver Auto Setup Procedure, users should use one of
the following two methods to install the driver after the system restart.
Method 1. Run Reboot Setup
Windows Vista will block startup programs by default when installing drivers
after the system restart. You must select taskbar icon Run Blocked Program
and run Reboot Setup to install the next driver, until you finish all drivers
installation.
Method 2. Disable UAC (User Account Control)
* For administrator account only. Standard user account can only use Method 1.
Disable Vista UAC function before installing drivers, then use CD driver to install
drivers, it will continue to install drivers after system restart without running blocked
programs.
34
Chapter 4: Software & Applications
Follow these instructions to Disable Vista UAC function:
1.
Go to Control Panel.
2.
Select Classic View.
3.
Set User Account.
35
Motherboard User’s Guide
4.
Select Turn User Account Control on or off and press Continue.
5. Disable User Account Control (UAC) to help protect your computer item and
press OK, then press Restart Now. Then you can restart your computer and continue to
install drivers without running blocked programs.
Bundled Software Installation
All bundled software available on the CD-ROM is for users’ convenience. You can
install bundled software as follows:
1
Click the Application button while the Auto Setup screen pops out
after inserting the support CD-ROM.
2
A software menu appears. Click the software you want to install.
3
Follow onscreen instructions to install the software program step by
step until finished.
36
Chapter 5: VIA VT8237 SATA RAID Setup Guide
Chapter 5 VIA VT8237 SATA RAID Setup Guide
VIA RAID Configurations
The motherboard includes a high performance Serial ATA RAID controller
integrated in the VIA VT8237 Southbridge chipset. It supports RAID 0, RAID
1 and JBOD with two independent Serial ATA channels.
RAID: (Redundant Array of Independent Disk Drives) use jointly several hard
drives to increase data transfer rates and data security. It depends on the number
of drives present and RAID function you select to fulfill the seurity or performance pruposes or both.
RAID 0 (called data striping) optimizes two identical hard disk drives to read
and write data in parallel, interleaved stacks. Two hard disks perform the same
work as a single drive but at a sustained data transfer rate, double that of a single
disk alone, thus improving data access and storage.
RAID 1 (called data mirroring) copies and maintains an identical image of data
from one drive to a second drive. If one drive fails, the disk array management
software directs all applications to the surviving drive as it contains a complete
copy of the data in the other drive. This RAID configuration provides data
protection and increases fault tolerance to the entire system.
JBOD: (Just a Bunch of Drives) Also known as “Spanning”. Two or more hard
drives are required. Several hard disk types configured as a single hard disk. The
hard drives are simply hooked up in series. This expands the capacity of your
drive and results in a useable total capacity. However, JBOD will not increase
any performance or data security.
Install the Serial ATA (SATA) hard disks
The VIA VT8237 Southbridge chipset supports Serial ATA hard disk drives. For
optimal performance, install identical drives of the same model and capacity
when creating a RAID set.
•
If you are creating a RAID 0 (striping) array of performance, use two
new drives.
•
If you are creating a RAID 1 (mirroring) array for protection, you can
use two new drives or use an existing drive and a new drive (the new
drive must be of the same size or larger than the existing drive). If you
use two drives of different sizes, the smaller capacity hard disk will be
the base storage size. For example, one hard disk has an 80 GB storage
capacity and the other hard disk has 60 GB storage capacity, the
maximum storage capacity for the RAID 1 set is 60 GB.
37
Motherboard User’s Guide
Follow these steps to install the SATA hard disks for RAID configuration.
i Before setting up your new RAID array, verify the status of your hard
disks. Make sure the Master/Slave jumpers are configured properly.
ii Both the data and power SATA cables are new cables. You cannot use
older 40-pin 80-conductor IDE or regular IDE power cables with Serial
ATA drives. Installing Serial ATA (SATA) hard disks require the use of
new Serial ATA cable (4-conductor) which supports the Serial ATA
protocol and a Serial ATA power cable.
iii Either end of the Serial ATA data cable can be connected to the SATA
hard disk or the SATA connector on the motherboard.
1 Install the Serial ATA hard disks into the drive bays.
2 Connect one end of the Serial ATA cable to the motherboard’s primary
Serial ATA connector (SATA1).
3 Connect the other end of Serial ATA cable to the master Serial ATA hard
disk.
4 Connect one end of the second Serial ATA cable to the motherboard’s
secondary Serial ATA connector (SATA2).
5 Connect the other end of Serial ATA cable to the secondary Serial ATA
hard disk.
6 Connect the Serial ATA power cable to the power connector on each
drive.
7 Proceed to section “Entering VIA Tech RAID BIOS Utility” for the next
procedure.
Entering VIA Tech RAID BIOS Utility
1 Boot-up your computer.
2 During POST, press <TAB> to enter VIA RAID configuration utility.
The following menu options will appear.
The RAID BIOS information on the setup screen shown is for
reference only. What you see on your screen may not by exactly
the same as shown.
38
Chapter 5: VIA VT8237 SATA RAID Setup Guide
On the upper-right side of the screen is the message and legend box. The keys on
the legend box allow you to navigate through the setup menu options. The
message describes the function of each menu item. The following lists the keys
found in the legend box with their corresponding functions.
F1
View Array
mn
Move to the next item
Enter
Confirm the selection
ESC
Exit
Create Array
1 In the VIA RAID BIOS utility main menu, select Create Array then
press the <Enter> key. The main menu items on the upper-left corner of
the screen are replaced with create array menu options.
RAID 0 for performance
1 Select the second option item Array Mode, then press the <Enter> key.
The RAID system setting pop-up menu appears.
2
3
Select RAID 0 for performance from the menu and press <Enter>.
From this point, you may choose to auto-configure the RAID array by
selecting Auto Setup for Performance or manually configure the RAID
array for stripped sets. If you want to manually configure the RAID
array continue with next step, otherwise, proceed to step #5.
Select Select Disk Drives, then press <Enter>. Use arrow keys to
select disk drive/s, then press <Enter> to mark selected drive. An
asterisk is placed before the selected drive.
39
Motherboard User’s Guide
4
Select Block Size, then press <Enter> to set array block size. Lists of
valid array block sizes are displayed on a pop-up menu.
Tip
For server systems, it is recommended to use a
lower array block size. For multimedia computer
systems used mainly for audio and video editing,
a higher array block size is recommended for
optimum performance.
Use arrow keys to move selection bar on items and press <Enter> to select.
5
Select Start Create Process and press <Enter> to setup hard disk for
RAID system. The following confirmation appears:
The same confirmation message appears when
the Auto Setup for Performance option is selected.
Press “Y” to confirm or “N” to return to the configuration options.
RAID 1 for data protection
1
Select the second option item Array Mode, then press the <Enter> key.
The RAID system setting pop-up menu appears.
2
Select RAID 1 for data protection from the menu and press <Enter>.
Select next task from pop-up menu. The task Create only creates the
mirrored set without creating a backup. Create and duplicate creates
both mirrored set and backup.
40
Chapter 5: VIA VT8237 SATA RAID Setup Guide
3
4
5
Select task and press <Enter>. The screen returns to Create Array menu
items. From this point, you may choose to auto-configure the RAID
array by selecting Auto Setup for Data Security or manually configure
the RAID array for mirrored sets. If you want to manually configure the
RAID array continue with next step, otherwise, proceed to step #5.
Select Select Disk Drives, then press <Enter>. Use arrow keys to select
disk drive/s, then press <Enter> to mark selected drive. (An asterisk is
placed before a selected drve.)
Select Start Create Process and press <Enter> to setup hard disk for
RAID system. The following confirmation message appears:
The same confirmation message appears when
the Auto Setup for Performance option is selected.
Press “Y” to confirm or “N” to return to the configuration options.
Delete Array
1 In the VIA RAID BIOS utility main menu, select Delete Array then
press the <Enter> key. The focus is directed to the list of channel used for
IDE RAID arrays.
2 Press the <Enter> key to select a RAID array to delete. The following
confirmation message appears.
Press “Y” to confirm or “N” to return to the configuration options.
Select Boot Array
1
2
In the VIA RAID BIOS utility main menu, select Select Boot Array then
press the <Enter> key. The focus is directed to the list of channel used
for IDE RAID arrays.
Press the <Enter> key to select a RAID array for boot. The Status of the
selected array will change to Boot. Press <ESC> key to go return to
menu items. Follow the same procedure to deselect the boot array.
41
Motherboard User’s Guide
Serial Number View
1 In the VIA RAID BIOS utility main menu, select Serial Number View
then press the <Enter> key. The focus is directed to the list of channel
used for IDE RAID arrays. Move the selection bar on each item and the
serial number is displayed at the bottom of the screen. This option is
useful for identifying same model disks.
Duplicate Critical RAID 1 Array
When booting up the system, BIOS will detect if the RAID 1 array has any
inconsistencies between user data and backup data. If BIOS detects any
inconsistencies, the status of the disk array will be marked as critical, and BIOS
will prompt the user to duplicate the RAID 1 in order to ensure the backup data
consistency with the user data.
If user selects Continue to boot, it will enable duplicating the array after
booting into OS.
42
Chapter 5: VIA VT8237 SATA RAID Setup Guide
Rebuild Broken RAID 1 Array
When booting up the system, BIOS will detect if any member disk drives of
RAID has failed or is absent. If BIOS detects any disk drive failures or missing
disk drives, the status of the array will be marked as broken.
If BIOS detects a broken RAID 1 array but there is a spare hard drive available
for rebuilding the broken array, the spare hard drive will automatically become
the mirroring drive. BIOS will show a main interface just like a duplicated
RAID 1. Selecting Continue to boot enables the user to duplicate the array
after booting into operating system.
If BIOS detects a broken RAID 1 array but there is no spare hard drive available
for rebuilding the array, BIOS will provide several operations to solve such
1. Power off and Check the Failed Drive:
This item turns off the computer and replaces the failed hard drive with a good
one. If your computer does not support APM, you must turn off your
computer manually. After replacing the hard drive, boot into BIOS and select
Choose replacement drive and rebuild to rebuild the broken array.
2. Destroy the Mirroring Relationship:
This item cancels the data mirroring relationship of the broken array. For broken
RAID 1 arrays, the data on the surviving disk will remain after the destroy
operation. However, Destroy the Mirroring Relationship is not recommended because the data on the remaining disk will be lost when the hard drive is
used to create another RAID 1 array.
43
Motherboard User’s Guide
3. Choose Replacement Drive and Rebuild:
This item enables users to select an already-connected hard drive to rebuild the
broken array. After choosing a hard drive, the channel column will be activated.
Highlight the target hard drive and press <Enter>, a warning message will appear.
Press Y to use that hard drive to rebuild, or press N to cancel. Please note
selecting option Y will destroy all the data on the selected hard drive.
4. Continue to boot:
This item enables BIOS to skip the problem and continue booting into OS.
44
Chapter 5: VIA VT8237 SATA RAID Setup Guide
Installing RAID Software & Drivers
Install Driver in Windows OS
New Windows OS (2000/XP/NT4) Installation
The following details the installation of the drivers while installing Windows XP.
1 Start the installation:
Boot from the CD-ROM. Press F6 when the message “Press F6 if you
need to install third party SCSI or RAID driver’ appears.
2 When the Windows Setup window is generated, press S to specify an
Additional Device(s).
3 Insert the driver diskette VIA VT8237 Disk Driver into drive A: and
press <Enter>.
4 Depending on your operation system, choose VIA Serial ATA RAID
Controller (Windows XP), VIA Serial ATA RAID Controller
(Windows 2000) or VIA Serial ATA RAID Controller (Windows
NT4) from the list that appears on Windows XP Setup screen, press the
<Enter> key.
5 Press <Enter> to continue with installation or if you need to specify any
additional devices to be installed, do so at this time. Once all devices are
specified, press <Enter> to continue with installation.
6 From the Windows XP Setup screen press the <Enter> key. Setup will
now load all device files and the continue the Windows XP installation.
Existing Windows XP Driver Installation
1
2
3
4
Insert the supported CD into the CD-ROM drive.
The CD will auto-run and the setup screen will appear.
Under the Driver tab, click on VIA SATA RAID Utility.
The drivers will be automatically installed.
Confirming Windows XP Driver Installation
1
2
3
From Windows XP, open the Control Panel from My Computer
followed by the System icon.
Choose the Hardware tab, then click the Device manager tab.
Click the “+” in front of the SCSI and RAID Controllers hardware
type. The driver VIA IDE RAID Host Controller should appear.
45
Motherboard User’s Guide
Installation of VIA SATA RAID Utility
The VIA SATA RAID Utility is the software package that enables highperformance RAID 0 arrays in the Windows*XP operating system. This
version of VIA SATA RAID Utility contains the following key features:
• Serial ATA RAID driver for Windows XP
• VIA SATA RAID utility
• RAID0 and RAID1 functions
Insert the supported CD and click on the Setup to install the software.
The InstallShield Wizard will begin automatically for installation. Click on the
Next button to proceed the installation in the welcoming window.
46
Chapter 5: VIA VT8237 SATA RAID Setup Guide
Put a check mark in the check box to install the feature you want. Then click
Next button to proceed the installation.
Using VIA RAID Tool
Once the installation is complete, go to Start---> Programs---> VIA--->
raid_tool.exe to enable VIA RAID Tool.
After the software is finished installation, it will
automatically started every time Windows is
initiated. You may double-click on the
icon shown in the system tray of the tool bar to
launch the VIA RAID Tool utility.
47
Motherboard User’s Guide
The main interface is divided into two windows and the toolbar above contain
the main functions. Click on these toolbar buttons to execute their specific
functions. The left windowpane displays the controller and disk drives and the
right windowpane displays the details of the controller or disk drives. The
available features are as following:
View by Controller
View by Devices
View Event log
Help Topics
It means that VT8237 SATA RAID only has the feature of monitoring the
statuses of RAID 0 and RAID 1.
Click on
or
button to determine the viewing type of left windowpane. There are two viewing types: By controllers and by device. Click on the
object in the left windowpane to display the status of the object in the right
windowpane. The following screen shows the status of Array 0-RAID 0.
48
Chapter 5: VIA VT8237 SATA RAID Setup Guide
Click on the plus (+) symbol next to Array 0--RAID 0 to see the details of each
disk.
You may also use the same
Array 0--RAID 1.
or
button to view the statuses of
49
Motherboard User’s Guide
Click on the plus (+) symbol next to Array 0; RAID 1 to see the details of each
disk.
50
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement