Husqvarna 122HD 45, 60 hedge trimmer Operator’s manual

H1153993-26,122HD45,60,#6DE7.fm Page 1 Friday, March 2, 2012 10:05 AM
GB
SE
DK
FI
DE
FR
NL
ES
PT
IT
RU
Operator’s manual 2-20
Bruksanvisning 21-39
Brugsanvisning 40-58
Käyttöohje 59-77
Bedienungsanweisung 78-97
Manuel d’utilisation 98-117
Gebruiksaanwijzing 118-137
Manual de instrucciones 138-157
Instruções para o uso 158-177
Istruzioni per l’uso 178-197
óêîâîäñòâî ïî
ýêñïëóàòàöèè 198-218
BG úêîâîäñòâî çà
åêñïëîàòàöèß 219-237
RO Instrucöiuni de utilizare 238-257
GR
EE
LV
LT
CZ
SK
PL
HU
HR
NO
SI
BA
RS
TR
√‰ËÁ›Â˜ ¯Ú‹Ûˆ˜ 258-277
Käsitsemisõpetus 278-295
Lieto‰anas pamÇc¥ba 296-314
Naudojimosi instrukcijos 315-333
Návod k pouÏití 334-353
Návod na obsluhu 354-372
Instrukcja obs∏ugi 373-392
Használati utasítás 393-412
Priruãnik 413-431
Bruksanvisning 432-451
Navodila za uporabo 452-470
Uputstvo o upotrebi 471- 490
Priruãnik 491- 510
Kullanım kılavuzu 511- 530
122HD45
122HD60
H1153993-26,122HD45,60#4ACBF.fm Page 2 Tuesday, January 4, 2011 8:31 AM
KEY TO SYMBOLS
Symbols
WARNING! Incorrect or careless use of a
hedge trimmer can turn it into a
dangerous tool that can cause serious or
even fatal injury. It is extremely important
that you read and understand the
contents of this operator’s manual.
Please read the operator’s manual
carefully and make sure you
understand the instructions before
using the machine.
The engine is switched off by moving the
stop switch to the stop position.
CAUTION! The stop switch
automatically returns to the start
position. In order to prevent
unintentional starting, the spark plug
cap must be removed from the spark
plug when assembling, checking and/or
performing maintenance.
Always wear approved protective
gloves.
Always wear:
•
Approved hearing protection
•
Approved eye protection
This product is in accordance with
applicable EC directives.
Regular cleaning is required.
Visual check.
Always wear approved protective gloves.
Protective goggles or a visor must be
worn.
Wear sturdy, non-slip boots or shoes.
Noise emission to the environment
according to the European Community’s
Directive. The machine’s emission is
specified in chapter Technical data and on
label.
Starting instructions See
the instructions under the
heading Start and stop.
Other symbols/decals on the machine refer to special
certification requirements for certain markets.
2 – English
H1153993-26,122HD45,60#4ACBF.fm Page 3 Tuesday, January 4, 2011 8:31 AM
CONTENTS
Contents
KEY TO SYMBOLS
Symbols ................................................................
CONTENTS
Contents ...............................................................
Note the following before starting: ........................
INTRODUCTION
Dear Customer, ....................................................
WHAT IS WHAT?
What is what? .......................................................
GENERAL SAFETY PRECAUTIONS
Important ..............................................................
Personal protective equipment .............................
Machine′s safety equipment .................................
FUEL HANDLING
Fuel safety ............................................................
Fuel ......................................................................
Fuelling .................................................................
STARTING AND STOPPING
Check before starting ...........................................
Starting and stopping ...........................................
WORKING TECHNIQUES
General working instructions ................................
MAINTENANCE
Carburettor ...........................................................
Muffler ..................................................................
Cooling system .....................................................
Spark plug ............................................................
Air filter .................................................................
Gear .....................................................................
Cutting unit ...........................................................
Cleaning and lubrication .......................................
Maintenance schedule .........................................
TECHNICAL DATA
Technical data ......................................................
EC-declaration of conformity ................................
Note the following before starting:
Please read the operator’s manual carefully.
2
3
3
!
4
5
!
6
6
7
10
10
11
12
12
!
WARNING! Long-term exposure to noise
can result in permanent hearing
impairment. So always use approved
hearing protection.
WARNING! Under no circumstances may
the design of the machine be modified
without the permission of the
manufacturer. Always use genuine
accessories. Non-authorized
modifications and/or accessories can
result in serious personal injury or the
death of the operator or others.
WARNING! Incorrect or careless use of a
hedge trimmer can turn it into a
dangerous tool that can cause serious or
even fatal injury. It is extremely important
that you read and understand the
contents of this operator’s manual.
14
16
16
16
16
17
17
17
17
18
19
20
English – 3
H1153993-26,122HD45,60#4ACBF.fm Page 4 Tuesday, January 4, 2011 8:31 AM
INTRODUCTION
Dear Customer,
Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689,
when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production
of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the waterpowered plant. During the more than 300 years of beeing, the Husqvarna factory has produced a lot of different products,
from wood stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the first motor
driven lawn mowers appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working today.
Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our
highest priority. The business concept is to develop, manufacture and market motor driven products for forestry and
gardening as well as for building and construction industry. Husqvarna′s aim is also to be in the front edge according to
ergonomics, usability, security and environmental protection. That is the reason why we have developed many different
features to provide our products within these areas.
We are convinced that you will appreciate with great satisfaction the quality and performance of our product for a very
long time to come. The purchase of one of our products gives you access to professional help with repairs and service
whenever this may be necessary. If the retailer who sells your machine is not one of our authorised dealers, ask for the
address of your nearest service workshop.
It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this
operator′s manual as a valuable document. By following its′ content (using, service, maintenance etc) the life span and
the second-hand value of the machine can be extended. If you will sell this machine, make sure that the buyer will get
the operator′s manual.
Thank you for using a Husqvarna product.
Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and
appearance of products without prior notice.
4 – English
H1153993-26,122HD45,60#4ACBF.fm Page 5 Tuesday, January 4, 2011 8:31 AM
WHAT IS WHAT?
What is what?
1
Operator′s manual
12 Lock for handle 122HD60
2
Handle
13 Throttle control
3
Throttle lock
14 Spark plug cap and spark plug
4
Fuel cap
15 Cylinder cover
5
Choke control
16 Starter handle
6
Front handle
17 Stop switch
7
Blade and blade guard
18 Lubricant filler cap, gear
8
Transport guard
19 Gear
9
Air filter cover
20 Hand guard
10 Air purge
21 Combination spanner
11 Fuel tank
22 Tube of grease
English – 5
H1153993-26,122HD45,60#4ACBF.fm Page 6 Tuesday, January 4, 2011 8:31 AM
GENERAL SAFETY PRECAUTIONS
Important
Personal protective equipment
IMPORTANT!
IMPORTANT!
The machine is only designed for cutting branches and
twigs.
Incorrect or careless use of a hedge trimmer can turn it
into a dangerous tool that can cause serious or even
fatal injury. It is extremely important that you read and
understand the contents of this operator’s manual.
Never use a machine that has been modified in any way
from its original specification.
Never use the machine if you are tired, if you have drunk
alcohol, or if you are taking medication that could affect
your vision, your judgement or your co-ordination.
Wear personal protective equipment. See instructions
under the heading ”Personal protective equipment”.
Never use the machine in extreme weather conditions
such as severe cold, very hot and/or humid climates.
Never use a machine that is faulty. Carry out the checks,
maintenance and service instructions described in this
manual. Some maintenance and service measures
must be carried out by trained and qualified specialists.
See instructions under the heading Maintenance.
All covers and guards must be fitted before starting.
Ensure that the spark plug cap and ignition lead are
undamaged to avoid the risk of electric shock.
!
!
!
!
6 – English
WARNING! This machine produces an
electromagnetic field during operation.
This field may under some
circumstances interfere with active or
passive medical implants. To reduce the
risk of serious or fatal injury, we
recommend persons with medical
implants to consult their physician and
the medical implant manufacturer before
operating this machine.
You must use approved personal protective equipment
whenever you use the machine. Personal protective
equipment cannot eliminate the risk of injury but it will
reduce the degree of injury if an accident does happen.
Ask your dealer for help in choosing the right equipment.
!
HEARING PROTECTION
Wear hearing protection that provides adequate noise
reduction.
EYE PROTECTION
Always wear approved eye protection. If you use a visor
then you must also wear approved protective goggles.
Approved protective goggles must comply with standard
ANSI Z87.1 in the USA or EN 166 in EU countries.
WARNING! Running an engine in a
confined or badly ventilated area can
result in death due to asphyxiation or
carbon monoxide poisoning.
GLOVES
WARNING! Never allow children to use or
be in the vicinity of the machine. As the
machine is equipped with a springloaded stop switch and can be started by
low speed and force on the starter
handle, even small children under some
circumstances can produce the force
necessary to start the machine. This can
mean a risk of serious personal injury.
Therefore remove the spark plug cap
when the machine is not under close
supervision.
BOOTS
WARNING! Faulty blades can increase
the risk of accidents.
WARNING! Listen out for warning signals
or shouts when you are wearing hearing
protection. Always remove your hearing
protection as soon as the engine stops.
Gloves should be worn when necessary, e.g., when fitting
cutting attachments.
Wear sturdy, non-slip boots or shoes.
H1153993-26,122HD45,60#4ACBF.fm Page 7 Tuesday, January 4, 2011 8:31 AM
GENERAL SAFETY PRECAUTIONS
CLOTHING
Wear clothes made of a strong fabric and avoid loose
clothing that can catch on twigs and branches. Always
wear heavy, long pants. Do not wear jewellery, shorts
sandals or go barefoot. Secure hair so it is above shoulder
level.
FIRST AID KIT
Always have a first aid kit nearby.
Make sure the throttle control is locked at the idle setting
when the throttle lockout is released.
Press the throttle lockout and make sure it returns to its
original position when you release it.
Machine′s safety equipment
This section describes the machine′s safety equipment,
its purpose, and how checks and maintenance should be
carried out to ensure that it operates correctly. See the
”What is what?” section to locate where this equipment is
positioned on your machine.
The life span of the machine can be reduced and the risk
of accidents can increase if machine maintenance is not
carried out correctly and if service and/or repairs are not
carried out professionally. If you need further information
please contact your nearest service workshop.
Check that the throttle control and throttle lockout move
freely and that the return springs work properly.
See instructions under the heading Start. Start the hedge
trimmer and apply full throttle. Release the throttle trigger
and check that the blades stop and remain stationary. If
the blades move when the throttle trigger is in the idle
position then the carburettor idle setting must be adjusted.
See instructions under the heading Maintenance.
IMPORTANT!
All servicing and repair work on the machine requires
special training. This is especially true of the machine′s
safety equipment. If your machine fails any of the checks
described below you must contact your service agent.
When you buy any of our products we guarantee the
availability of professional repairs and service. If the
retailer who sells your machine is not a servicing dealer,
ask him for the address of your nearest service agent.
Stop switch
!
WARNING! Never use a machine with
faulty safety equipment. The machine’s
safety equipment must be checked and
maintained as described in this section. If
your machine fails any of these checks
contact your service agent to get it
repaired.
Throttle lockout
The throttle lockout is designed to prevent accidental
operation of the throttle control. When you press the lock
(A) (i.e. when you grasp the handle) it releases the throttle
control (B). When you release the handle the throttle
control and the throttle lockout both move back to their
original positions. This movement is controlled by two
independent return springs. This arrangement means that
the throttle control is automatically locked at the idle
setting.
Use the stop switch to switch off the engine.
Start the engine and make sure the engine stops when
you move the stop switch to the stop setting. The stop
switch automatically returns to the start position. In order
to prevent unintentional starting, the spark plug cap must
be removed from the spark plug when assembling,
checking and/or performing maintenance.
English – 7
H1153993-26,122HD45,60#4ACBF.fm Page 8 Tuesday, January 4, 2011 8:31 AM
GENERAL SAFETY PRECAUTIONS
Hand guard
Muffler
The hand guard prevents hands from coming into contact
with the moving blades, for example, if the operator loses
grip on the front handle.
The muffler is designed to keep noise levels to a minimum
and to direct exhaust fumes away from the user. A muffler
fitted with a catalytic converter is also designed to reduce
harmful exhaust gases.
Check that the hand guard is fitted correctly.
In countries that have a warm and dry climate there is a
significant risk of fire. We therefore fit certain mufflers with
a spark arrestor mesh. Check whether the muffler on your
machine is fitted with this kind of mesh.
Check that the hand guard is undamaged.
Vibration damping system
Your machine is equipped with a vibration damping
system that is designed to minimize vibration and make
operation easier.
For mufflers it is very important that you follow the
instructions on checking, maintaining and servicing your
machine.
Never use a machine that has a faulty muffler.
The machine′s vibration damping system reduces the
transfer of vibration between the engine unit/cutting
equipment and the machine′s handle unit.
The engine body, including the blades, is suspended on
the handlebar using four rubber bushings.
Regularly check that the muffler is securely attached to
the machine.
Regularly check the vibration damping units for cracks or
deformation. Check that the vibration damping element is
undamaged and securely attached.
!
8 – English
WARNING! Overexposure to vibration
can lead to circulatory damage or nerve
damage in people who have impaired
circulation. Contact your doctor if you
experience symptoms of overexposure
to vibration. Such symptoms include
numbness, loss of feeling, tingling,
pricking, pain, loss of strength, changes
in skin colour or condition. These
symptoms normally appear in the
fingers, hands or wrists. The risk
increases at low temperatures.
If the muffler on your machine is fitted with a spark
arrestor mesh this must be cleaned regularly. A blocked
mesh will cause the engine to overheat and may lead to
serious damage.
!
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.
This also applies at idle speed. Contact
can result in burns to the skin.
Remember the risk of fire!
H1153993-26,122HD45,60#4ACBF.fm Page 9 Tuesday, January 4, 2011 8:31 AM
GENERAL SAFETY PRECAUTIONS
!
!
WARNING! The inside of the muffler
contain chemicals that may be
carcinogenic. Avoid contact with these
elements in the event of a damaged
muffler.
WARNING! Bear in mind that: The
exhaust fumes from the engine are hot
and may contain sparks which can start
a fire. Never start the machine indoors or
near combustible material!
Blade and blade guard
The outer part of the blades (1) are shaped as blade
guards. The blade guard is intended to protect against
any part of the body coming into contact with the blades.
Check that the blade guard is not damaged or distorted.
Replace the cutting unit if it is bent or damaged.
Gear
The gear housing gets hot when the machine has been in
use. To avoid burning yourself do not touch the gear
housing.
English – 9
H1153993-26,122HD45,60#4ACBF.fm Page 10 Tuesday, January 4, 2011 8:31 AM
FUEL HANDLING
Fuel safety
Petrol
Never start the machine:
1
If you have spilt fuel on it. Wipe off the spillage and
allow remaining fuel to evaporate.
2
If you have spilt fuel on yourself or your clothes,
change your clothes. Wash any part of your body that
has come in contact with fuel. Use soap and water.
3
If the machine is leaking fuel. Check regularly for
leaks from the fuel cap and fuel lines.
Transport and storage
•
Store and transport the machine and fuel so that there
is no risk of any leakage or fumes coming into contact
with sparks or naked flames, for example, from
electrical machinery, electric motors, electrical relays/
switches or boilers.
CAUTION! Always use a quality petrol/oil mixture at least
90 octane (RON). If your machine is equipped with a
catalytic converter (see chapter on Technical data) always
use a good quality unleaded petrol/oil mixture. Leaded
petrol will destroy the catalytic converter.
Use low-emission petrol, also known as alkylate petrol, if
it is available.
•
The lowest octane recommended is 90 (RON). If you
run the engine on a lower octane grade than 90 socalled knocking can occur. This gives rise to a high
engine temperature, which can result in serious
engine damage.
When working at continuous high revs a higher octane
rating is recommended.
•
When storing and transporting fuel always use
approved containers intended for this purpose.
•
When storing the machine for long periods the fuel
tank must be emptied. Contact your local petrol
station to find out where to dispose of excess fuel.
•
•
Ensure the machine is cleaned and that a complete
service is carried out before long-term storage.
Two-stroke oil
•
The transport guard must always be fitted to the
cutting attachment when the machine is being
transported or in storage.
•
For best results and performance use HUSQVARNA
two-stroke engine oil, which is specially formulated for
our air-cooled two-stroke engines.
•
Secure the machine during transport.
•
Never use two-stroke oil intended for water-cooled
engines, sometimes referred to as outboard oil (rated
TCW).
•
Never use oil intended for four-stroke engines.
•
A poor oil quality and/or too high oil/fuel ratio may
jeopardise function and decrease the life time of
catalytic converters.
•
Mixing ratio
!
WARNING! Take care when handling fuel.
Bear in mind the risk of fire, explosion
and inhaling fumes.
Fuel
CAUTION! The machine is equipped with a two-stroke
engine and must always been run using a mixture of
petrol and two-stroke oil. It is important to accurately
measure the amount of oil to be mixed to ensure that the
correct mixture is obtained. When mixing small amounts
of fuel, even small inaccuracies can drastically affect the
ratio of the mixture.
!
WARNING! Fuel and fuel fumes are
highly inflammable and can cause
serious injury when inhaled or allowed to
come in contact with the skin. For this
reason observe caution when handling
fuel and make sure there is adequate
ventilation.
10 – English
1:50 (2%) with HUSQVARNA two-stroke oil.
1:33 (3%) with oils class JASO FB or ISO EGB
formulated for air-cooled, two-stroke engines.
Petrol, litre
Two-stroke oil, litre
2% (1:50)
3% (1:33)
5
0,10
0,15
10
0,20
0,30
15
0,30
0,45
20
0,40
0,60
H1153993-26,122HD45,60#4ACBF.fm Page 11 Tuesday, January 4, 2011 8:31 AM
FUEL HANDLING
Fuelling
Mixing
•
Always mix the petrol and oil in a clean container
intended for fuel.
•
Always start by filling half the amount of the petrol to
be used. Then add the entire amount of oil. Mix
(shake) the fuel mixture. Add the remaining amount of
petrol.
•
!
Mix (shake) the fuel mixture thoroughly before filling
the machine’s fuel tank.
WARNING! Taking the following
precautions, will lessen the risk of fire:
Do not smoke or place hot objects near
fuel.
Always shut off the engine before
refuelling.
Refuel in a well ventilated area. Never
fuel the machine indoors.
Always stop the engine and let it cool for
a few minutes before refuelling.
•
Do not mix more than one month’s supply of fuel at a
time.
•
If the machine is not used for some time the fuel tank
should be emptied and cleaned.
!
WARNING! The catalytic converter
muffler gets very hot during and after
use. This also applies during idling. Be
aware of the fire hazard, especially when
working near flammable substances and/
or vapours.
When refuelling, open the fuel cap slowly
so that any excess pressure is released
gently.
Tighten the fuel cap carefully after
refuelling.
Always move the machine away from the
refuelling area and source before
starting.
•
Always use a fuel container with an anti-spill valve.
•
Clean the area around the fuel cap. Contamination in
the tank can cause operating problems.
•
Ensure that the fuel is well mixed by shaking the
container before filling the tank.
English – 11
H1153993-26,122HD45,60#4ACBF.fm Page 12 Tuesday, January 4, 2011 8:31 AM
STARTING AND STOPPING
Check before starting
•
•
•
•
•
•
•
•
Inspect the working area. Remove any objects that
could be thrown out.
Check the cutting attachment. Never use blades that
are dull, cracked or damaged.
Check that the machine is in perfect working order.
Check that all nuts and screws are tight.
Make sure the gear housing is lubricated correctly.
See instructions under the heading Gear housing.
Check that the cutting attachment always stops when
the engine is idling.
Only use the machine for the purpose it was intended
for.
Make sure that the handle and safety features are in
good working order. Never use a machine that lacks a
part or has been modified outside its specifications.
All covers must be correctly fitted and undamaged
before you start the machine.
Starting and stopping
!
Primer bulb: Press the air purge diaphragm repeatedly
until fuel begins to fill the diaphragm (about 6 times). The
diaphragm need not be completely filled.
Starting
Hold the body of the machine on the ground using your
left hand (CAUTION! Not with your foot!). Grip the starter
handle, slowly pull out the cord with your right hand until
you feel some resistance (the starter pawls grip), now
quickly and powerfully pull the cord. Never twist the
starter cord around your hand.
WARNING! The complete gear housing
must be fitted before the machine is
started, otherwise the clutch may loosen
and cause personal injury.
Always move the machine about 3
metres from the refuelling position
before starting. Place the machine on a
firm surface. Remember that the blades
may start to move when the engine is
started. Make sure the blades cannot
come into contact with any object. Make
sure that no unauthorised persons are in
the working area, otherwise there is a
risk of serious personal injury. The safety
distance is 15 metres.
Cold engine
Choke:
Set the choke control in the choke position.
12 – English
Push the choke control back to its original position as
soon as the engine fires, and continue trying to start until
the engine starts.
CAUTION! When the choke control is pushed back to its
original position, the engine runs at a heightened speed,
the so called start throttle position, and the blades then
move. Start throttle position is released by throttling using
the throttle lever.
CAUTION! Do not pull the starter cord all the way out and
do not let go of the starter handle when the cord is fully
extended. This can damage the machine.
H1153993-26,122HD45,60#4ACBF.fm Page 13 Tuesday, January 4, 2011 8:31 AM
STARTING AND STOPPING
Warm engine
Hold the body of the machine on the ground using your
left hand (CAUTION! Not with your foot!). Grip the starter
handle, slowly pull out the cord with your right hand until
you feel some resistance (the starter pawls grip), now
quickly and powerfully pull the cord. Never twist the
starter cord around your hand.
Stopping
The engine is switched off by moving the stop switch to
the stop position.
CAUTION!
The stop switch automatically returns to the start position.
In order to prevent unintentional starting, the spark plug
cap must be removed from the spark plug when
assembling, checking and/or performing maintenance.
English – 13
H1153993-26,122HD45,60#4ACBF.fm Page 14 Tuesday, January 4, 2011 8:31 AM
WORKING TECHNIQUES
General working instructions
Safety instructions while working
IMPORTANT!
This section takes up the basic safety precautions for
working with a hedge trimmer.
If you encounter a situation where you are uncertain
how to proceed you should ask an expert. Contact your
dealer or your service workshop.
Avoid all usage which you consider to be beyond your
capability.
!
WARNING! The machine can cause
serious personal injury. Read the safety
instructions carefully. Learn how to use
the machine.
!
WARNING! Cutting tool. Do not touch the
tool without first switching off the
engine.
Safety instructions regarding the
surroundings
•
Never allow children to use the machine.
•
Observe your surroundings and make sure that there
is no risk of people or animals coming into contact
with the cutting equipment.
•
Ensure that no-one comes closer than 15 m while you
are working.
•
Never allow anyone else to use the machine without
first ensuring that they have understood the contents
of the operator’s manual.
•
Never work from a ladder, stool or any other raised
position that is not fully secured.
•
•
Always ensure you have a safe and stable working
position.
•
Never leave the machine unsupervised with the motor
running.
•
Always use both hands to hold the machine. Hold the
machine in front of your body.
•
Make sure that your hands and feet do not come near
the cutting attachment when the engine is running.
•
When the engine is switched off, keep your hands and
feet away from the cutting attachment until it has
stopped completely.
•
Watch out for stumps of branches that can be thrown
out during cutting.
•
Do not cut too close to the ground. Stones and other
objects can be thrown out.
•
Check the working area for foreign objects such as
electricity cables, insects and animals, etc, or other
objects that could damage the cutting attachment,
such as metal items.
•
If any foreign object is hit or if vibrations occur stop the
machine immediately. Disconnect the HT lead from
the spark plug. Check that the machine is not
damaged. Repair any damage.
•
If anything jams in the blades while you are working,
switch off the engine and wait until it has stopped
completely before cleaning the blades. Disconnect the
HT lead from the spark plug.
Keep in mind that the operator is responsible for
accidents or hazards occuring to other people or their
property.
14 – English
H1153993-26,122HD45,60#4ACBF.fm Page 15 Tuesday, January 4, 2011 8:31 AM
WORKING TECHNIQUES
If the blades get stuck, they can be loosened by
sticking the combination spanner into the gear
housing. Remove the lubricant plug and stick the
combination spanner into the gearing and turn it back
and forth.
Basic working techniques
•
Work with a swinging action from the bottom upwards
when trimming sides.
•
Adjust the throttle setting to suit the load.
•
When trimming a hedge the engine should always
face away from the hedge.
•
Hold the machine as close to your body as possible to
get the best balance.
•
Make sure that the tip does not touch the ground.
•
Do not rush the work, but work steadily until all the
branches have been cut back cleanly.
Safety instructions after completing work
•
The transport guard should always be fitted to the
cutting attachment when the machine is not in use.
•
Make sure the cutting attachment has stopped before
cleaning, carrying out repairs or an inspection.
Disconnect the HT lead from the spark plug.
•
Always wear heavy-duty gloves when repairing the
cutting attachment. This is extremely sharp and can
easily cause cuts.
122HD60
•
Store the machine out of reach of children.
•
Use only original spare parts for repairs.
The hedge trimmer’s rear handle can be set in five
positions by pulling out the catch. See figure. When the
handle is adjusted, the hedge trimmer must be idling or
not running.
•
While working the handle should always be facing
upwards irrespective of how the hedge trimmer is
directed.
English – 15
H1153993-26,122HD45,60#4ACBF.fm Page 16 Tuesday, January 4, 2011 8:31 AM
MAINTENANCE
Carburettor
Adjustment of the idle speed
Before any adjustments are made, make sure that the air
filter is clean and the air filter cover is fitted. Make sure the
start throttle position is disengaged.
Adjust the idle speed using the idle adjustment screw T, if it
is necessary to readjust. First turn the T screw clockwise until
the cutting attachment starts to move. Then turn the screw
anticlockwise until the cutting attachment stops. The idle
speed is correctly adjusted when the engine runs smoothly
in every position. The idle speed should also be well below
the speed at which the cutting attachment starts to move.
Rec. idle speed: See the Technical data section.
On mufflers fitted with a catalytic converter, the mesh
must be checked, and if necessary cleaned, monthly. If
the mesh is damaged it must be replaced. If the mesh
is frequently blocked, this can be a sign that the
performance of the catalytic converter is impaired.
Contact your dealer to inspect the muffler. A blocked
mesh will cause the machine to overheat and result in
damage to the cylinder and piston.
CAUTION! Never use a machine with a defective muffler.
!
WARNING! Mufflers fitted with catalytic
converters get very hot during use and
remain so for some time after stopping.
This also applies at idle speed. Contact
can result in burns to the skin.
Remember the risk of fire!
Cooling system
!
WARNING! If the idle speed cannot be
adjusted so that the cutting attachment
stops, contact your dealer/service
workshop. Do not use the machine until
it has been correctly adjusted or
repaired.
To keep the working temperature as low as possible the
machine is equipped with a cooling system.
Muffler
CAUTION! Some mufflers are fitted with a catalytic
converter. See chapter on Technical data to see whether
your machine is fitted with a catalytic converter.
The muffler is designed to reduce the noise level and to
direct the exhaust gases away from the operator. The
exhaust gases are hot and can contain sparks, which may
cause fire if directed against dry and combustible material.
Some mufflers are equipped with a special spark arrestor
mesh. If your machine has this type of muffler, the mesh must
be cleaned. This is best done with a wire brush.
On mufflers without a catalytic converter, the mesh should be
cleaned or replaced if necessary once a week. If the mesh
is damaged it must be replaced. If the mesh is frequently
blocked, this can be a sign that the carburettor is incorrectly
adjusted or that too much oil has been mixed with the petrol.
16 – English
The cooling system consists of:
1 Cooling fins on the cylinder.
2 Cylinder cover (directs cold air over the cylinder).
3 Air intake through the crankcase (inside the tank).
Clean the cooling system with a brush once a week, more
often in demanding conditions. A dirty or blocked cooling
system results in the machine overheating which causes
damage to the piston and cylinder.
Spark plug
The spark plug condition is influenced by:
• Incorrect carburettor adjustment.
• An incorrect fuel mixture (too much or incorrect type
of oil).
• A dirty air filter.
These factors cause deposits on the spark plug
electrodes, which may result in operating problems and
starting difficulties.
If the machine is low on power, difficult to start or runs
poorly at idle speed: always check the spark plug first
before taking any further action. If the spark plug is dirty,
clean it and check that the electrode gap is 0,5 mm. The
H1153993-26,122HD45,60#4ACBF.fm Page 17 Tuesday, January 4, 2011 8:31 AM
MAINTENANCE
spark plug should be replaced after about a month in
operation or earlier if necessary.
Gear
There is a plug for filling lubricant on the gear housing.
Use the grease tube to fill with grease and repeat every
25 hours. Use Husqvarna’s special grease.
CAUTION! Always use the recommended spark plug type!
Use of the wrong spark plug can damage the piston/cylinder.
Check that the spark plug is fitted with a suppressor.
Air filter
The air filter must be regularly cleaned to remove dust
and dirt in order to avoid:
• Carburettor malfunctions
• Starting problems
• Loss of engine power
• Unnecessary wear to engine parts.
• Excessive fuel consumption.
Clean the filter every 25 hours, or more regularly if
conditions are exceptionally dusty.
Cleaning the air filter
Remove the air filter cover and take out the filter. Wash it
clean in warm, soapy water. Allow the filter to dry and then
oil it in according to the instructions.
An air filter that has been in use for a long time cannot be
cleaned completely. The filter must therefore be replaced
with a new one at regular intervals. A damaged air filter
must always be replaced.
Oiling the air filter
CAUTION! The gear housing must not be filled
completely with grease. The grease expands as the
machine heats up during operation. If the gear housing
was completely filled with grease it could damage the
seals and lead to leakage of grease.
The grease in the bevel gear does not normally need to
be changed except if repairs are carried out.
Cutting unit
Check that the cutting units' screws are fitted correctly.
Tighten them with a tightening torque of 7-10 Nm.
Cleaning and lubrication
Clean any resin and plant residue from the blades using
cleaning agent 531 00 75-13 (UL22) before and after
using the machine.
Check that the blade edges are not damaged or
deformed. File away any burrs.
Check that the blades move freely. Remove the
lubrication plug in the gear housing and stick in the
combination spanner and turn back and forth.
Always use HUSQVARNA filter oil, art. no. 531 00 92-48.
The filter oil contains a solvent to make it spread evenly
through the filter. You should therefore avoid skin contact.
Put the filter in a plastic bag and pour the filter oil over it.
Knead the plastic bag to distribute the oil. Squeeze the
excess oil out of the filter inside the plastic bag and pour
off the excess before fitting the filter to the machine. Never
use common engine oil. This would drain through the filter
quite quickly and collect in the bottom.
Lubricate the blade bars with special grease, part no. 531
00 75-12 (UL 21) before long periods of storage.
English – 17
H1153993-26,122HD45,60#4ACBF.fm Page 18 Tuesday, January 4, 2011 8:31 AM
MAINTENANCE
Maintenance schedule
The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the
Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s
Manual. More extensive work must be carried out by an authorized service workshop.
After 40
hours in use
After 100
hours in use
Maintenance
Before use:
Clean the outside of the machine.
After each time the machine is used
Make sure the throttle trigger lock and the throttle function correctly
from a safety point of view.
X
In order to reduce the risk of fire, dirt, leaves and surplus lubricant, etc
must be cleaned from the muffler, exhaust pipe and engine.
X
Check that the stop switch works correctly.
X
Check that the blades do not move when the engine is idling.
X
Check that the blades are undamaged and show no signs of cracking
or other damage. Replace the blades if necessary.
X
Check that the blade guard is not damaged or distorted. Replace the
blade if the blade guard is bent or damaged.
X
Replace the cutting unit if it is bent or damaged.
X
Check that the hand guard is not damaged. Replace the guard if
damaged.
X
Check that nuts and screws are tight.
X
Check that there are no fuel leaks from the engine, tank or fuel lines.
X
Clean the air filter and oil it in.
Clean more often if conditions are exceptionally dusty.
(25 tim).
Check the starter and starter cord.
X
Check that the vibration damping elements are not damaged.
X
Clean the outside of the spark plug. Remove it and check the electrode
gap. Adjust the gap to 0.5 mm or replace the spark plug. Check that
the spark plug is fitted with a suppressor.
X
Clean the machine’s cooling system.
X
Clean the outside of the carburettor and the space around it.
X
Fill the gear housing with grease. This should be carried out
approximately every 25 working hours.
X
Check that the screws that hold the blades together are correctly
tightened.
X
Check and clean the spark arrestor mesh on the muffler (only applies
to mufflers fitted with a catalytic converter).
X
Clean the inside of the fuel tank.
X
Check the inside of the fuel filter for any dirt or if the fuel hose has any
cracks or other defects. Replace if necessary.
X
Check all cables and connections.
X
Check the clutch, clutch springs and the clutch drum for wear. Replace
if necessary by an autorized service workshop.
X
Replace the spark plug. Check that the spark plug is fitted with a
suppressor.
X
18 – English
H1153993-26,122HD45,60#4ACBF.fm Page 19 Tuesday, January 4, 2011 8:31 AM
TECHNICAL DATA
Technical data
Technical data
122HD45
122HD60
Engine
Cylinder displacement, cm3
21,7
21,7
Cylinder bore, mm
32
32
Stroke, mm
27
27
Idle speed, rpm
2900
2900
Recommended max. speed, rpm
9000
9000
Max. engine output, acc. to ISO 8893, kW/ rpm
0,6/7800
0,6/7800
Catalytic converter muffler
Yes
Yes
Speed-regulated ignition system
Yes
Yes
Spark plug
NGK CMR6A
NGK CMR6A
Electrode gap, mm
0,5
0,5
0,3
0,3
4,7
4,9
Sound power level, measured dB(A)
100
100
Sound power level, guaranteed LWA dB(A)
101
101
93
94
2,9/4,9
4,1/3,6
Type
Double sided
Double sided
Length, mm
450
590
Blade speed, cuts/min
4050
4050
Ignition system
Fuel and lubrication system
Fuel tank capacity, litre
Weight
Weight without fuel, kg
Noise emissions
(see note 1)
Sound levels
(see note 2)
Equivalent sound pressure level at the operator’s ear, measured
according to EN ISO 10517, dB(A):
Vibration levels
(see note 3)
Equivalent vibration levels (ahv,eq) at handles, measured according to
EN ISO 10517, m/s2
Front/rear handles:
Blades
Note 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/14/
EC. Reported sound power level for the machine has been measured with the original cutting attachment that gives the
highest level. The difference between guaranteed and measured sound power is that the guaranteed sound power also
includes dispersion in the measurement result and the variations between different machines of the same model
according to Directive 2000/14/EC.
Note 2: Reported data for equivalent sound pressure level for the machine has a typical statistical dispersion (standard
deviation) of 1 dB (A).
Note 3: Reported data for equivalent vibration level has a typical statistical dispersion (standard deviation) of 1 m/s2.
English – 19
H1153993-26,122HD45,60#4ACBF.fm Page 20 Tuesday, January 4, 2011 8:31 AM
TECHNICAL DATA
EC-declaration of conformity (Applies to Europe only)
Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that the hedge
trimmers Husqvarna 122HD45 and 122HD60 from 2011’s serial numbers and onwards (the year is clearly stated in
plain text on the type plate with subsequent serial number), are in conformity with the standards or or other normative
documents following the provisions in the COUNCIL’S DIRECTIVES:
- of May 17, 2006 "relating to machinery" 2006/42/EC
- of December 15, 2004 ”relating to electromagnetic compatibility” 2004/108/EC.
- of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. Conformity assessment according
to Annex V.
For information relating to noise emissions, see the chapter Technical data. The following standards have been applied:
EN ISO 12100-2:2009, CISPR 12:2007, EN ISO 10517:2009
SMP Svensk Maskinprovning AB, Fyrisborgsgatan 3, SE-754 50 Uppsala, Sweden, has performed voluntary type
examination on behalf of Husqvarna AB. The certificates are numbered: SEC/10/2280 - 122HD45, SEC/10/2280 122HD60
Huskvarna December 1, 2010
Bo Jonsson, Development manager
(Authorized representative for Husqvarna AB and responsible for technical documentation.)
20 – English