Yamaha | CDX-E100 | Owner's Manual | Yamaha RX-E100 Owner's manual

BG
RX-E100 / CDX-E100
Natural Sound Stereo Receiver/Natural Sound Compact Disc Player
Récepteur Stéréo/Lecteur Compact Disque
L
R
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
SUPPLIED ACCESSORIES •
ACCESSOIRES FOURNIS
•
MITGELIEFERTES ZUBEHÖR •
MEDFÖLJANDE TILLBEHÖR •
ACCESSORI IN DOTAZIONE •
After unpacking, check that the following parts are contained.
Après le déballage, vérifier que les pièces suivantes sont incluses.
Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind.
Kontrollera efter det apparaten packats upp att följande delar finns med.
Verificare che tutte le parti seguenti siano contenute nell’imballaggio
dell’apparecchio.
ACCESORIOS INCLUIDOS • Desembale el aparato y verificar que los siguientes accesorios están en la caja.
BIJGELEVERDE ACCESSOIRES • Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.
<RX-E100>
•
•
•
•
•
•
•
Remote control
Télécommande
Fernbedienungseinheit
Fjärrkontrollen
Telecomando
Mando a distancia
Afstandbediening
SLEEP
REP
AM loop antenna
Antenne cadre AM
MW-Rahmenantenne
AM ramantenn
Antenna AM ad uso interno
Antena de cuadro de AM
AM ringantenne
•
•
•
•
•
•
•
Indoor FM antenna
Antenne intérieure FM
UKW-Innenantenne
FM inomhusantenn
Antenna FM per interni
Antena interior de FM
FM binnenantenne
•
•
•
•
•
•
•
Batteries (size AAA, UM-4, R03)
Piles (format AAA, UM-4, R03)
Batterien (Größe AAA, UM-4, R03)
Batterier (Storl. AAA, UM-4, R03)
Batterie (size AAA, o UM-4, o R03)
Pilas (tamaño AAA, tipo UM-4, R03)
Batterijen (maat AAA, UM-4, R03)
•
•
•
•
•
•
•
System Control Cable
Câble de commande du système
Systemsteuerkabel
Systemkontrollkabel
Cavo di telecomando del sistema
Cable de control del sistema
Systeembedieningskabel
DISP
TIME
A
C
PROG
B
RNDM
D
•
•
•
•
•
•
•
PEAK
E
TAPE
FREQ PS/PTY/RT/CT
PTY SEEK
MODE
START
VOLUME
TAPE
MD
AUX
CD
TUNER
MD REC
PRESET
PTY SELECT
TAPE REC
TAPE
MODE
START
DUBBING
<CDX-E100>
•
•
•
•
•
•
•
RCA Pin Cable
Câble de raccordement RCA
RCA-Stiftkabel
RCA stiftkabel
Cavo con spinotti a spillo RCA
Cable con clavijas RCA
RCA (tulpstekker) kabel
ENGLISH
Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment. For the
best performance, read this manual carefully. It will guide you in operating your YAMAHA product.
FEATURES
<RX-E100>
<CDX-E100>
• Minimum RMS Output Power per Channel
40 W + 40 W (6Ω, 20 - 20,000Hz, 0.1% THD)
• Full Operation System Remote Control
• 40-Station FM/AM Preset Tuning
• Multi-Function RDS Reception
• SUBWOOFER Output Terminal
•
•
•
•
•
•
S-bit DAC and 8fs Digital Filter
Optical Digital Output
Random, Repeat, and Program Play
CD TEXT Display
Peak Level Search
Tape Programming
The receiver (RX-E100) and CD player (CDX-E100) are the main units of the YAMAHA E100 series. You could upgrade
the system by adding the cassette deck (KX-E100) and MD recorder (MDX-E100)*.
* MD recorder (MDX-E100) may not be available for some areas.
CONTENTS
PRECAUTIONS ................................................... 2
<CDX-E100>
GETTING STARTED
The remote control ............................................... 3
Connecting the speakers ....................................... 4
Connecting the system .......................................... 5
NAMES OF BUTTONS AND CONTROLS ..... 17
<RX-E100>
NAMES OF BUTTONS AND CONTROLS ....... 6
BASIC OPERATIONS
Listening to a source ............................................. 8
TUNER OPERATIONS
Listening to the radio ............................................ 9
Presetting stations ............................................... 10
RECEIVING RDS STATIONS
Receiving RDS data ........................................... 11
PTY SEEK mode ................................................ 12
Optional settings for RDS functions ................... 13
USING THE BUILT-IN TIMER
Setting the clock ................................................. 14
Adjusting the brightness of the display .............. 14
Before using the timer ........................................ 15
Timer play and recording ................................... 15
Sleep timer .......................................................... 16
COMPACT DISC PLAYER OPERATIONS
CD playback ....................................................... 19
Selecting the time display and CD TEXT .......... 20
Random-sequence play ....................................... 20
Repeat play ......................................................... 21
Program play ...................................................... 21
Peak level search ................................................ 22
ADD KX-E100 AND/OR MDX-E100 TO YOUR
SYSTEM
Operating the cassette deck, KX-E100 and MD
recorder, MDX-E100 with the remote control ... 23
Before recording ................................................. 24
Dubbing setting .................................................. 24
TAPE programming ............................................ 25
ADDITIONAL INFORMATION
CD preventive care ............................................. 26
Troubleshooting .................................................. 26
Specifications ..................................................... 28
E-1
English
INTRODUCTION
PRECAUTIONS: READ THIS BEFORE OPERATING THE UNIT
CAUTIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
Install your unit in a well ventilated, cool, dry, clean
place – away from windows, heat sources, vibration,
dust, moisture, or cold. To avoid humming sounds,
locate the unit away from other electrical appliances,
motors, and transformers. To prevent fire or electrical
shock, do not expose to rain and water.
(U.K. and Europe models only)
Be sure to allow at least 10 cm of ventilation space at
the top, on left, right, and back sides of RX-E100.
Do not operate the unit upside-down. It may overheat,
possibly causing damage.
Never open the cabinet. If something drops into the set,
contact your dealer.
Do not use force on switches, knobs or cords.
Always set the VOLUME control to minimum before
starting playback of an audio source: increase the
volume gradually to an appropriate level after play has
started.
When not planning to use this unit for long periods of
time (i.e., vacation, etc.), disconnect the AC power plug
from the wall outlet.
Grounding or polarization – Precautions should be taken
so that the grounding or polarization of the unit is not
defeated.
Do not clean the unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
Be sure to read the “Troubleshooting” section on
common operating errors before concluding that your
unit is faulty.
Do not place another component on top of this unit, as
damage or discoloration on the surface of the unit may
result.
To prevent damage by lightning, disconnect the power
cord from the wall outlet during an electrical storm.
When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
Do not plug the AC power plug to the wall outlet before
you finish all connections.
The voltage to be used must be the same as that
specified on this unit. Using this unit with a higher
voltage than that which is specified is dangerous and
may result in a fire or other type of accident causing
damage. YAMAHA will not be held responsible for any
damage resulting from use of this unit with a voltage
other than that which is specified.
When listening to the receiver at a high volume level for
a long time, the temperature inside the unit rises. To
prevent overheating and possible damage to this unit,
the internal fan starts running.
Sudden temperature changes and storage or operation in
an extremely humid environment may cause
condensation inside the cabinet.
The unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off. This state is called the standby
mode. In this state, this unit is designed to consume a
very small quantity of power.
CAUTION FOR CARRYING THE UNIT
Before carrying the unit, first remove all discs from
the unit, press STANDBY/ON to turn the unit off,
then disconnect the AC power plug from the wall
outlet.
SPECIAL INSTRUCTIONS FOR U.K. MODEL
IMPORTANT:
The wires in the mains lead are coloured in accordance
with the following code:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows: The wire which is coloured BLUE
must be connected to the terminal which is marked
with the letter N or coloured BLACK. The wire which
is coloured BROWN must be connected to the terminal
which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
For U.K. customers
If the socket outlets in the home are not suitable for the
plug supplied with this appliance, it should be cut off and
an appropriate 3 pin plug fitted. For details, refer to the
instructions described above.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous
if engaged in a live socket outlet.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
CLASS 1 LASER PRODUCT
This compact disc player is
classified as a CLASS 1
LASER product.
The CLASS 1 LASER
PRODUCT label is located
on the rear exterior.
Laser component in this product is capable of
emitting radiation exceeding the limit for Class 1.
E-2
GETTING STARTED
This remote control controls a whole system: not only
RX-E100 but also CDX-E100. Moreover, a cassette deck
(KX-E100) and MD recorder (MDX-E100) that level up
your system can be operated by it. Operating buttons for
each unit are explained on the pages below:
Receiver, RX-E100:
CD player, CDX-E100:
Cassette deck, KX-E100:
MD recorder, MDX-E100:
p.7
p.18
p.23
p.23
Notes
• Use only AAA, UM-4, R03 batteries for replacement.
• Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
• Remove the batteries if the remote control will not be used for
an extended period of time.
• If batteries leak, dispose of them immediately. Avoid touching
the leaked material or letting it come in contact with clothing,
etc. Clean the battery compartment thoroughly before
installing new batteries.
Remote control operation range
NATURAL SOUND STEREO RECEIVER RX-E100
Loading the batteries for the remote control
1
VOLUME
DISPLAY
Remove the battery compartment cover.
MEMORY
AUTO/MAN'L
TIME ADJ
TIMER
PRESET/BAND
PRESET/TUNING
MIN
STANDBY/ON
HOUR
BASS
PHONES
-
+
TREBLE
MIN
BALANCE
-
L
+
MAX
INPUT
R
Remote control
sensor
2
Within approximately
6 m (20 feet)
Insert 4 batteries into the battery compartment.
30°
30°
Notes
3
Replace the battery compartment cover.
• There should be no large obstacles between the remote control
and the main unit.
• If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp, etc.),
it might cause the remote control not to work correctly. In this
case, reposition the main unit to avoid direct lighting.
Battery replacement
If you find that the remote control must be used closer to
the main unit than usual, the batteries are weak. Replace
batteries with new ones.
E-3
English
The remote control
GETTING STARTED
Connecting the speakers
Never plug the AC power cord to the wall outlet until all connections are completed.
Follow the steps as shown below to connect the system using the supplied cords and accessories.
Right speaker
Left speaker
3 FM antenna
2 AM loop antenna
75 Ω UNBAL
FREQUENCY
STEP
FM ANT
B
A
GND
AM ANT
E
R
L
L
CD
TAPE
R
OUT
IN
IN
L
SUBWOOFER
SYSTEM
CONNETOR
AUX
MD
OUT
R
6 Ω MIN./SPEAKER
D
C
SPEAKERS
1
1
Connect the Speakers.
1 Unscrew the knob.
2 Remove approx. 5 mm (1/4”) of insulation from
each of the speaker wires and insert the bare wire
into the terminal.
3 Tighten the knob to secure the wire.
Red: positive(+)
Black: negative(–)
3
75 Ω UNBAL
FM ANT
4
2
Connect the FM Antenna.
Connect the AC power cord to a wall outlet.
1
3
2
4 To wall outlet
Connect the AM Antenna.
Set up the AM loop antenna, then connect it.
• Use external FM/AM antennas if you need better reception.
Consult your dealer.
• The AM loop antenna should be placed apart from the main
unit. The antenna may be hung on a wall.
To Connect the Subwoofer (optional)
You can reinforce the bass frequencies by adding a
subwoofer (optional).
Connect the SUBWOOFER OUT terminal of the unit to
the INPUT terminal of the subwoofer.
GND
E-4
AM ANT
GETTING STARTED
English
Connecting the system
Connecting RX-E100 and CDX-E100
1
2
3
Connect ‰ to ‰ using the RCA pin cable.
Insert the plugs into the jacks of the same colour.
Connect RX-E100 and CDX-E100 with the system control cable.
The other SYSTEM CONNECTOR of CDX-E100 is for connecting MDX-E100 or KX-E100.
Connect the AC power plug of CDX-E100 to AC OUTLET of RX-E100.
<CDX-E100>
To RX-E100
3
ANALOG
DIGITAL
OPTICAL
E OUT
L
SYSTEM
CONNECTOR
OUT
R
1
System control cable
RCA pin cable
<RX-E100>
75 Ω UNBAL
FREQUENCY
STEP
FM ANT
B
A
GND
AM ANT
E
R
L
L
CD
TAPE
2
R
OUT
IN
IN
L
SUBWOOFER
SYSTEM
CONNETOR
AUX
MD
OUT
R
6 Ω MIN./SPEAKER
D
C
SPEAKERS
To wall outlet
Adding KX-E100 and MDX-E100 to the above system (For details, refer to the owner's manual
supplied with the respective component.)
1
2
3
4
Connect Å and ı of RX-E100 to Å and ı of KX-E100.
Connect Ç and Î of RX-E100 to Ç and Î of MDX-E100.
Connect an external component to the AUX terminal of RX-E100.
Connect DIGITAL OPTICAL OUT of CDX-E100 to DIGITAL OPTICAL IN of MDX-E100.
Take off the covers of the optical fiber cable plug, the DIGITAL OPTICAL OUT jack, and the DIGITAL OPTICAL
IN jack before making digital connections. Be sure to replace the terminal’s cover when the terminal on the rear panel
is not being used, in order to protect from dust.
5
AC OUTLET (CDX-E100)
Connect the AC power plug of MDX-E100 or KX-E100 (Except for the UK model).
E-5
RX-E100 NAMES OF BUTTONS AND CONTROLS
Front panel
NATURAL SOUND STEREO RECEIVER RX-E100
VOLUME
TIMER
STANDBY
DISPLAY
MEMORY
AUTO/MAN'L
TIME ADJ
TIMER
PRESET/BAND
PRESET/TUNING
MIN
STANDBY/ON
HOUR
BASS
PHONES
-
~
Ÿ
!
⁄
@
¤
#
‹
$
+
PTY SELECT
MIN
TREBLE
BALANCE
-
+
L
MAX
INPUT
R
› VOLUME (P.8)
% PRESET/TUNING / PTY SELECT
(P.9/P.12)
HOUR/MIN (P.14)
fi PRESET/BAND (P.9)
^ Display (P.6)
fl Remote Control Sensor (P.3)
& TIMER indicator (P.15)
‡ STANDBY indicator (P.8)
STANDBY/ON (P.8)
PHONES (P.8)
DISPLAY (P.14)
MEMORY/TIME ADJ (P.10/P.14)
AUTO/MAN’L/TIMER (P.9/P.15)
BASS (P.8)
TREBLE (P.8)
BALANCE (P.8)
INPUT (P.8)
Display
PRESET
STEREO
TUNED
~
Ÿ
!
⁄
@
¤
Multi-information display
PRESET indicator (P.10)
STEREO indicator (P.9)
TUNED indicator (P.9)
AUTO indicator (P.9)
MEMORY indicator (P.10)
E-6
AUTO RDS PS PTY RT CT
MEMORY
PTY HOLD
#
‹
$
›
%
TIMER
SLEEP
RDS indicator (P.11)
RDS mode indicators (P.11)
PTY HOLD indicator (P.12)
TIMER indicator (P.15)
SLEEP indicator (P.16)
RX-E100 NAMES OF BUTTONS AND CONTROLS
SLEEP
DISP
TIME
A
REP
RNDM
D
C
PROG
B
PEAK
E
TAPE
FREQ PS/PTY/RT/CT
PTY SEEK
MODE
START
TAPE
AUX
~
Ÿ
!
⁄
@
¤
#
‹
$
›
%
fi
SLEEP (P.16)
DISP (Display) (P.13)
A/B/C/D/E (P.10)
POWER (P.8)
Preset numbers (P.10)
FREQ PS/PTY/RT/CT (P.11)
PTY SEEK MODE (P.12/P.13)
PTY SEEK START (P.12/P.13)
VOLUME + – (P.8)
TAPE (KX-E100) (P.23)
MD (MDX-E100) (P.23)
AUX (The equipment connected to the AUX
terminal) (P.5)
^ CD (CDX-E100) (P.19)
fl TUNER (RX-E100) (P.10)
& PRESET/PTY SELECT / (P.10/P.12)
Note
• ›~fl are operation buttons and input selectors for each
component.
VOLUME
MD
English
Remote control
CD
TUNER
MD REC
PRESET
PTY SELECT
TAPE REC
TAPE
MODE
START
DUBBING
E-7
RX-E100 BASIC OPERATIONS
Listening to a source
PHONES
TREBLE
4
Play the source. (Refer to the owner’s manual
supplied with each selected component.)
5
Adjust the volume level by turning VOLUME on the
front panel or pressing VOLUME + on the remote
control.
6
If desired, adjust BASS, TREBLE, and BALANCE.
VOLUME
NATURAL SOUND STEREO RECEIVER RX-E100
VOLUME
TIMER
STANTBY
DISPLAY
MEMORY
AUTO/MAN'L
TIME ADJ
TIMER
PRESET/BAND
PRESET/TUNING
MIN
STANDBY/ON
HOUR
BASS
PHONES
-
STANDBY/ON
+
PTY SELECT
MIN
TREBLE
BALANCE
-
BASS
R
TIME
C
PROG
B
RNDM
PEAK
BASS: Turn this control clockwise to increase (or
counterclockwise to decrease) the low frequency
response.
TREBLE: Turn this control clockwise to increase (or
counterclockwise to decrease) the high frequency
response.
BALANCE: Adjust the balance of the output volume
from the left and right speakers to compensate for
sound imbalance caused by the speaker location or
listening room conditions
DISP
A
D
L
BALANCE INPUT
SLEEP
REP
+
MAX
INPUT
E
TAPE
POWER
FREQ PS/PTY/RT/CT
When you use headphones
PTY SEEK
MODE
• These controls are only effective for the sound from the main
speakers.
START
VOLUME
VOLUME –/+
TAPE
MD
AUX
MD REC
PRESET
PTY SELECT
CD
Connect the headphones to the PHONES jack. You can
listen to the sound from the main speakers through the
headphones.
TUNER
TAPE REC
When you have finished using this
unit
TAPE
MODE
START
DUBBING
• The STANDBY indicator lights up.
1
Set the volume to “MIN” by turning VOLUME.
2
Turn on the power by pressing STANDBY/ON on
the front panel, or POWER on the remote control.
• RX-E100 can be used to turn on or put in standby mode
the system connected E100 series components depending
on their prior standby/on status.
3
Press STANDBY/ON on the front panel again or
POWER on the remote control to set this unit to the
standby mode.
Select the desired input source by turning INPUT so
that the source appears on the display.
• When you operate the component connected to the AUX
terminal, turn INPUT to select AUX.
E-8
Auto power off function
RX-E100 will be put automatically into the standby mode
under the following conditions:
• The component connected to RX-E100 is in stop mode
and not operated for 30 minutes.
• TUNER or AUX is not selected as an input source.
TUNER OPERATIONS
Manual tuning
1
Follow steps 1 and 2 described in “Automatic
tuning.”
2
Press AUTO/MAN’L so that “AUTO” disappears
from the display.
3
Press TUNING
(For a higher frequency) or
(For a lower frequency) to select your desired station.
You can find radio stations automatically and manually.
PRESET/TUNING
AUTO/MAN’L
/
NATURAL SOUND STEREO RECEIVER RX-E100
VOLUME
DISPLAY
MEMORY
AUTO/MAN'L
PRESET/BAND
PRESET/TUNING
MIN
TIME ADJ
STANDBY/ON
HOUR
TIMER
BASS
PHONES
-
+
PTY SELECT
MIN
TREBLE
BALANCE
-
+
L
MAX
English
Listening to the radio
• Each time you press TUNING
changes step by step.
or
, the frequency
INPUT
R
PRESET/BAND
INPUT
Automatic tuning
1
Select TUNER by turning INPUT so that the
frequency of a radio station appears in the display.
2
Press PRESET/BAND to select the reception band.
Do not select the preset tuning mode (in which
“PRESET” appears on the display).
3
Press AUTO/MAN’L so that “AUTO” appears in the
display.
4
Press PRESET/ TUNING
(For a higher
frequency) or
(For a lower frequency).
5
The unit starts searching for a station.
STEREO
AUTO
TUNED
When the unit finds a station, the unit stops searching
and “TUNED” appears on the display.
6
If the located station is not the one you want, repeat
steps 4 and 5 until a station you want is tuned.
Notes
• If automatic tuning search does not find the desired station, try
manual tuning as described next.
• When an FM stereo broadcast with sufficient signal strength is
received, “STEREO” appears on the display and you can listen
to stereo sound.
E-9
TUNER OPERATIONS
5
Presetting stations
The unit can preset station frequencies selected by
Automatic tuning or Manual tuning. Up to 40 stations can
be stored. With this function, you can select any desired
station by pressing the corresponding preset station
number.
PRESET/TUNING
/
NATURAL SOUND STEREO RECEIVER RX-E100
VOLUME
DISPLAY
MEMORY
AUTO/MAN'L
PRESET/BAND
PRESET/TUNING
MIN
TIME ADJ
STANDBY/ON
HOUR
TIMER
BASS
PHONES
-
+
MIN
PTY SELECT
TREBLE
BALANCE
-
+
L
MEMORY PRESET/BAND
MAX
INPUT
Notes
• A new setting can be preset in place of a previous one.
• The preset stations are retained for a week after you disconnect
the AC power cord or a power failure occurs.
To preset stations automatically
1
Select TUNER as input source by turning INPUT.
2
Press MEMORY for about 2 seconds.
• The unit starts presetting stations, “AUTO” and
“MEMORY” will flash on the display.
R
INPUT
To preset stations manually
1
Repeat steps 1 to 4 until all desired stations are
preset.
Tune in a desired station.
(Refer to the previous page for the tuning procedure.)
2
Press MEMORY.
3
Within about 5 seconds, use PRESET/TUNING
/ to select a desired preset number. Continue
pressing PRESET/TUNING / to select the
group of the preset stations (A, B, C, D, and E).
Received stations are stored to A1, A2...A8 sequentially.
After 40 stations or all FM and AM stations are stored, the
display will show the preset station A1.
To recall a preset station
Press TUNER and select the desired number by pressing
PRESET/BAND and PRESET/TUNING / on the
front panel or PRESET / , A/B/C/D/E and 1-8 on
the remote control.
SLEEP
DISP
TIME
A
REP
PROG
B
RNDM
D
PEAK
PRESET
C
A/B/C/D/E
E
TAPE
STEREO
1~8
TUNED MEMORY
FREQ PS/PTY/RT/CT
4
Press MEMORY.
PRESET
TAPE
MD
AUX
MD REC
PRESET
PTY SELECT
TUNER
CD
TUNER
PRESET
TAPE REC
TAPE
STEREO
TUNED MEMORY
MODE
START
DUBBING
E-10
START
VOLUME
• “MEMORY”, “PRESET”, and preset number will appear
on the display.
The arrow will appear for a second when
it is preset.
PTY SEEK
MODE
RECEIVING RDS STATIONS
RDS (Radio Data System) is a data transmission system
which has been introduced by FM stations in many
European countries. Stations using this system transmit an
inaudible stream of data in addition to the normal radio
signal. RDS data contains various types of information,
such as PS (Program Service), PTY (Program Type), RT
(Radio Text), and CT (Clock Time).
SLEEP
REP
The name of the RDS station being received is displayed.
• If the unit cannot find a station with PS data, the unit stops
searching and “NO PS” appears on the display.
RDS PS PTY RT CT
PTY
The type of the program on the RDS station now being
received is displayed. You can make this unit search for a
Playing
Started
CDs
station which is broadcasting a programGetting
of a desired
program type. (Refer to PTY program mode in the next
section for details.)
DISP
TIME
A
C
PROG
B
RNDM
D
PS
PEAK
E
RDS PS PTY RT CT
TAPE
RT
FREQ PS/
PTY/RT/CT
FREQ PS/PTY/RT/CT
PTY SEEK
MODE
START
VOLUME
TAPE
MD
AUX
MD REC
PRESET
PTY SELECT
TUNER
CD
Information about the program (such as the title of the
track, artist name, etc.) on the RDS station being received
is displayed using a maximum of 64 alphabetical
characters, including umlaut sign. If other characters are
used in the RT data, they are displayed with an under-bar.
• If the unit cannot find a station with RT data, the unit stops
searching and “NO RT” appears on the display.
TUNER
TAPE REC
RDS PS PTY RT CT
TAPE
CT
MODE
START
DUBBING
Current time is displayed.
• If the unit cannot find a station with CT data, the unit stops
searching and “NO CT” appears on the display.
RDS PS PTY RT CT
1
2
Tune in the FM station. (Refer to page 9, or you can
simply press TUNER on the remote control.)
Press FREQ PS/PTY/RT/CT to choose the mode.
Each time you press FREQ PS/PTY/RT/CT, the
type changes as follows:
English
Receiving RDS data
Note
• RDS may not work properly if the station you are tuned to is
not transmitting the RDS signal properly or if the signal
strength is weak.
• Some FM stations do not offer RDS service. Of those that do,
not all provide the same types of services. The types provided
by the received RDS station are dimmed on the display. Check
with your local radio stations for details on RDS services in
your area.
E-11
RECEIVING RDS STATIONS
To locate a station
PTY SEEK mode
You can locate a desired station by selecting a program
type. The unit searches all preset stations into the type of
programs currently being broadcast from the RDS
stations.
SLEEP
REP
Tune in the FM station. (Refer to page 9, or you can
simply press TUNER on the remote control.)
2
Press PTY SEEK MODE once so that “PTY” and a
PTY program flashes on the display.
DISP
TIME
A
C
PROG
B
RNDM
D
1
PEAK
E
PTY
TAPE
FREQ PS/PTY/RT/CT
Within about 20 seconds, press PTY SELECT
(for a higher frequency) or
(for a lower
frequency) until the desired program type appears on
the display.
4
Within about 20 seconds, press PTY SEEK START.
PTY SEEK MODE
PTY SEEK START
PTY SEEK
MODE
3
START
VOLUME
TAPE
MD
AUX
MD REC
PRESET
PTY SELECT
• If a station broadcasting the selected program type is
found, the unit stops searching and the Program Service
name appears on the display.
“PTY HOLD” appears on the display.
CD
TUNER
TAPE REC
TAPE
PTY SELECT
/
PRESET
RDS
PTY
PTY HOLD
MODE
START
DUBBING
5
List of PTY (Program Type)
NEWS
VARIED
News
Light Entertainment
AFFAIRS
POP M
Current Affairs
Pops
INFO
ROCK M
General Information
Rock
SPORT
M.O.R. M
Sports
Middle of the Road
Music (Easy-listening)
EDUCATE
Education
LIGHT M
DRAMA
Light Classics
Drama
CLASSICS
CULTURE
Serious Classics
Culture
OTHER M
SCIENCE
Other Music
Science
E-12
Repeat step 4 until the desired station is located.
If there is no station broadcasting the program type
you select, “NO PTY” appears on the display, then
the Program Service name or frequency appears on
the display.
RECEIVING RDS STATIONS
The tuner has the following functions which make use of
the RDS data service. These are originally in operation
ON. However, you can turn these functions OFF, if so
desired.
SLEEP
DISP
TIME
A
REP
B
PEAK
DISP
C
Getting
Playing
Started
CDs
E
TAPE
FREQ PS/PTY/RT/CT
FREQ PS/
PTY/RT/CT
2. LOCAL = CT (ON/OFF)
If the RDS station being received employs the
local time (summer time, etc.) data service, its time
is displayed in the CT mode.
PROG
RNDM
D
PTY SEEK
MODE
START
3. A.M. = RDS (ON/OFF)
RDS stations are searched instead of all FM
stations by the automatic preset tuning operation
when the setting is ON. (Refer to page 10.)
PTY SEEK MODE
PTY SEEK START
VOLUME
TAPE
MD
AUX
MD REC
PRESET
PTY SELECT
TUNER
CD
TUNER
TAPE REC
4. RT SPEED: ±0
Changes the scrolling speed of the radio text
decreasing the value and, in turn, reducing the
speed.
TAPE
MODE
English
• If you receive an RDS station of some other country, the
built-in clock is synchronized with the time setting of the
country.
• If the built-in clock is not yet set for the current time or
reset due to a power failure, etc., it will be set for the time
defs
of the CT data automatically, whether this setting is ON
or OFF.
Optional settings for
RDS functions
START
DUBBING
Control Range: ±0 to ±3 (Preset value: ±0)
1
Select the FM band by pressing TUNER.
2
Press DISP to display the current time.
3
Press FREQ PS/PTY/RT/CT.
4
Each time you press PTY SEEK MODE the display
will change as follows:
5
1. CT = CLOCK (ON/OFF)
The tuner corrects the time of the built-in clock
automatically by synchronizing it with the CT data
on the RDS station being received.
Choose the function ON or OFF by pressing PTY
SEEK START, confirming it in the display.
Press PTY SEEK START repeatedly to change the
value for RT SPEED.
• If there is no operation for about 20 seconds, this mode is
cancelled and turns into the frequency display. If the
station has PS data, it turns into the PS mode.
6
Press FREQ PS/PTY/RT/CT again to restore the
frequency display mode.
E-13
USING THE BUILT-IN TIMER
Setting the clock
You must set the clock before you use the timer functions.
The clock is based on a 24-hour system.
DISPLAY
HOUR
Adjusting the brightness
of the display
You can adjust the brightness of the display. If you have
connected the CD player (CDX-E100), cassette deck
(KX-E100), and/or MD recorder (MDX-E100) to this
unit, the brightness of the displays is automatically
adjusted to that of this unit.
MIN
NATURAL SOUND STEREO RECEIVER RX-E100
VOLUME
DISPLAY
DISPLAY
MEMORY
AUTO/MAN'L
PRESET/BAND
PRESET/TUNING
MIN
TIME ADJ
STANDBY/ON
HOUR
TIMER
BASS
PHONES
PTY SELECT
MIN
TREBLE
BALANCE
MAX
INPUT
NATURAL SOUND STEREO RECEIVER RX-E100
-
+
-
+
L
VOLUME
R
DISPLAY
MEMORY
AUTO/MAN'L
TIME ADJ
TIMER
PRESET/BAND
PRESET/TUNING
MIN
TIME ADJ
PRESET/BAND
STANDBY/ON
HOUR
BASS
PHONES
-
1
+
PTY SELECT
MIN
TREBLE
BALANCE
-
+
L
MAX
INPUT
R
While the power is on, press DISPLAY to display
the time.
INPUT
2
While holding TIME ADJ, press HOUR to set the
hour.
• If you want to move the time in the reverse direction,
press HOUR while holding TIME ADJ and PRESET/
BAND.
3
Press and hold DISPLAY for about two seconds so that
“Dimmer ±0” appears on the display. While holding
DISPLAY, turn INPUT clockwise to increase or
counterclockwise to decrease brightness.
While holding TIME ADJ, press MIN to set the
minutes.
• If you want to move the time in the reverse direction,
press MIN while holding TIME ADJ and PRESET/
BAND.
Control Range: ±0 to –6 (Preset value: ±0)
To display the clock
Press DISPLAY.
The current time appears for about 8 seconds, then the
normal display returns.
Note
• In the event of a power failure or when the AC power cord is
disconnected for more than five minutes, you must reset the
clock.
E-14
USING THE BUILT-IN TIMER
If you want to use the cassette deck, KX-E100 or the MD
Recorder, MDX-E100 for timer play or recording, you
must first make the connections as shown in “Connecting
the system” on page 5. For details, refer to the instructions
supplied with the MDX-E100 or KX-E100.
(Example)
4. ON Time
“ON Time” appears on the display for a second,
and changed to the time setting mode.
Press HOUR to set the hour.
Press MIN to set the minute.
Timer play and recording
By using the built-in timer, you can have the unit turn on
at a specified time and begin playing or recording
automatically. You can also specify the turn off time.
DISPLAY
MIN
5. OFF Time
Set the time the same way as above.
If you set the ON time but not OFF time, the timer
play or recording will finish automatically after an
hour.
NATURAL SOUND STEREO RECEIVER RX-E100
VOLUME
DISPLAY
MEMORY
AUTO/MAN'L
TIME ADJ
TIMER
PRESET/BAND
PRESET/TUNING
MIN
STANDBY/ON
HOUR
BASS
PHONES
PTY SELECT
MIN
TREBLE
BALANCE
MAX
INPUT
Notes
-
TIMER
1
+
-
+
HOUR
L
R
• The display mode will change in about 8 seconds. If the
mode is changed before the setting is completed, call the
mode again by pressing DISPLAY once or more.
• If you select the input other than TUNER and AUX on
“2. Timer Input”, “3. Timer REC” is skipped.
INPUT
Press DISPLAY.
Whenever DISPLAY is pressed, the display mode
changes as follows:
2
Press TIMER to complete the timer setting.
The system is put in the standby mode.
• The STANDBY and TIMER indicators light up.
1. Clock Time (TIMER on/off mode)
If you have not set the clock yet “Set Clock”
appears. You need to set the current time as
described on page 14.
If you continue using the system, press STANDBY/
ON to turn on this unit.
To cancel the timer play setting
2. Timer Input
Select the source to be played by turning INPUT.
• Timer recording is possible only when you select
TUNER or AUX.
Press DISPLAY to show the current time, then press
TIMER so that “TIMER” goes off from the display. You
can also cancel by pressing TIMER in standby mode.
Note
• In the event of a power failure or when the AC power cord is
disconnected for more than five minutes, you must reset the
clock.
E-15
English
3. Timer REC
Select the recording component by turning INPUT.
If you like to enjoy timer play with TUNER or
AUX, select “REC Mode OFF”.
Before using the timer
USING THE BUILT-IN TIMER
Sleep timer
The unit can be turned off automatically at a selected
SLEEP time.
SLEEP
SLEEP
DISP
TIME
A
REP
B
RNDM
D
C
PROG
E
PEAK
TAPE
1
Play the desired sound source.
2
Press SLEEP repeatedly until the desired sleep time
appears in the display.
Each time you press SLEEP, the sleep time changes
as follows:
SLEEP 2h00m
SLEEP 1h30m
SLEEP 1h00m
SLEEP 0h30m
SLEEP OFF
About 4 seconds after setting, the normal display will
resume.
• “SLEEP” will appear in the display.
E-16
3
The unit will turn off automatically when the selected
sleep time is reached.
CDX-E100 NAMES OF BUTTONS AND CONTROLS
English
Front panel
NATURAL SOUND COMPACT DISC PLAYER CDX-E100
STANDBY/ON
~ STANDBY/ON (P.19)
Ÿ Display (this page)
! $/! (Skip/Search Backward)
⁄/› (Skip/Search Forward) (P.19)
⁄ ^ (Play/Pause) (P.19)
@ & (Stop) (P.19)
¤ (Open/Close) (P.19)
# Disc Tray (P.19)
Display
REPEAT S F PROGRAM RANDOM 1 2 3 4 5 6 7 8 9 10
TITLE ARTIST TRACK CD-TEXT 11 12 13 14 15 16 17 18 19 20
~
Ÿ
!
⁄
@
Multi-information Display
* Pause indicator
# Play indicator
B Tape side indicator (P.25)
A
Music calendar
¤
#
‹
$
A
B
RANDOM indicator (P.20)
PROGRAM indicator (P.21)
REPEAT S/F (Single or Full) indicator (P.21)
CD-TEXT indicator (P.20)
E-17
CDX-E100 NAMES OF BUTTONS AND CONTROLS
Remote control
DISP
SLEEP
TIME
A
REP
RNDM
D
C
PROG
B
PEAK
E
TAPE
FREQ PS/PTY/RT/CT
PTY SEEK
MODE
START
VOLUME
TAPE
MD
AUX
CD
TUNER
MD REC
PRESET
PTY SELECT
TAPE REC
TAPE
MODE
START
DUBBING
E-18
~
Ÿ
!
⁄
@
¤
#
‹
$
›
%
fi
^
TIME (P.20)
REP (Repeat) (P.21)
PROG (Program) (P.21)
RNDM (Random) (P.20)
PEAK (Peak Search) (P.22)
TAPE (P.25)
POWER (P.19)
Numeric buttons (P.19)
CD input (P.19)
$/! (Skip/Seach Backward) (P.19)
›/⁄ (Skip/Seach Forward) (P.19)
^ (Play/Pause) (P.19)
& (Stop) (P.19)
COMPACT DISC PLAYER OPERATIONS
Press
tray.
to open the disc tray, and place a CD on the
& ^
100
X-E
CD
NATURAL SOUND COMPACT DISC PLAYER CDX-E100
D
UN
SO
T
AC
MP
CO
C
DIS
YER
PLA
AL
TUR
NA
/ON
DBY
STAN
STANDBY/ON
4
Press ^ to start playback.
The unit starts playback of the CD.
To pause playback
$/! ⁄/›
STANDBY/ON
SLEEP
REP
Press &.
C
PROG
B
RNDM
D
To stop playback
DISP
TIME
A
PEAK
Press ^.
To resume play, press ^ again.
E
To eject the CD
TAPE
POWER
Press to open the disc tray, and remove the CD from
the tray.
Numeric
buttons
FREQ PS/PTY/RT/CT
To play a specific track on the disc
(Skip)
PTY SEEK
MODE
START
VOLUME
Direct play
TAPE
MD
AUX
CD
CD
TUNER
$/!/›/⁄
MD REC
PRESET
PTY SELECT
TAPE REC
Skip play
TAPE
^
MODE
Select a desired track using the numeric button.
(Example: To select 35, press +10 three times so that
“3 –” appears in the display, then press 5.)
START
&
DUBBING
To play CDs
Press › to skip forward or $ to skip backward. Press
once for each track to be skipped.
Notes
• You cannot enter a number that is higher than the last track
number on the disc.
• These operations can also be performed when the unit is in the
pause or stop mode.
• During stop mode, if › or $ is pressed, the track number
successively changes to higher numbers (or lower numbers).
1
Press STANDBY/ON to turn on this unit and also
RX-E100.
To advance or reverse playback
rapidly (Search)
2
Press CD on the remote control in order to operate
the CD player by the remote control.
Press and hold ⁄ to advance playback rapidly, and !
to reverse playback rapidly.
E-19
English
3
CD playback
COMPACT DISC PLAYER OPERATIONS
Selecting the time
display and CD TEXT
Random-sequence play
The unit can play all the tracks in a random sequence.
You can select any of four time displays by pressing
TIME. When you play a CD with CD TEXT, the disc
title, artist name, and track name are also displayed.
DISP
SLEEP
TIME
A
REP
DISP
SLEEP
TIME
A
REP
B
RNDM
D
PEAK
RNDM
D
PEAK
TIME
C
B
C
PROG
RNDM
E
TAPE
PROG
E
TAPE
Press RNDM.
• “RANDOM” appears on the display.
The unit starts random sequence play.
Each time you press TIME, the display changes as
follows:
Elapsed time of the
current track
To cancel random-sequence play
mode
Press & or RNDM.
• “RANDOM” disappears from the display.
Remaining time of the
current track
Total disc play time
Total remaining time of
the disc
• “CD-TEXT” appears on the display if a
CD has CD TEXT.
Disc title
Artist name
Track name
Note
• The disc title, artist names, or track names may not be
displayed with some CD TEXT discs. In this case, “(NO
ENTRY)” appears on the display.
E-20
Notes
• This feature will not function during programming, or during
programmed play.
• If › is pressed during random-sequence play, the next
randomly programmed track will be played.
If $ is pressed, play will return to the beginning of the
current track.
• Total remaining time on the disc will not be displayed during
random-sequence play.
COMPACT DISC PLAYER OPERATIONS
You can play any desired track or disc repeatedly.
Press REP to select the repeat mode.
SLEEP
REP
B
RNDM
D
PEAK
By creating a program, you can enjoy listening to your
favourite tracks in any desired order. As many as 30
tracks can be programmed in sequence.
DISP
TIME
A
REP
Program play
SLEEP
DISP
TIME
A
C
REP
PROG
PROG
B
RNDM
D
C
PEAK
PROG
E
TAPE
E
TAPE
Numeric
buttons
FREQ PS/PTY/RT/CT
PTY SEEK
MODE
START
VOLUME
TAPE
SINGLE REPEAT
The current track is played repeatedly.
MD
AUX
MD REC
PRESET
PTY SELECT
CD
TUNER
REPEAT
TAPE REC
›/$
S
TAPE
^
MODE
START
&
DUBBING
FULL REPEAT
The current disc is played repeatedly.
• In random-sequence play mode, all randomly sequenced tracks
are played repeatedly in the same order.
REPEAT
1
Press & to stop the unit.
2
Press PROG.
F
• “PROGRAM” appears in the display.
To cancel repeat play mode
PROGRAM
Press REP successively until “REPEAT F” disappears
from the display.
3
Use the numeric buttons to select a track number
until the desired track number appears on the display.
PROGRAM
4
Repeat step 3 to program more tracks. You can select
the same track again.
5
Press ^ to start program play.
E-21
English
Repeat play
COMPACT DISC PLAYER OPERATIONS
To stop program play mode
Peak level search
Press &.
Note
• › or $ can be used during program play to skip to tracks
within the program.
This unit can find the peak sound level on the CD for
optimum adjustment of the recording volume level.
To check program data
DISP
SLEEP
1.
2.
Press & to stop program play.
Press PROG. Then each time you press › / $,
the track number and the program number are
displayed in the order of the program.
TIME
A
REP
RNDM
D
PEAK
B
PEAK
C
PROG
E
TAPE
To change program data
1.
2.
3.
Follow the preceding procedure described in “To
check program data.”
Display the track number to be changed by pressing
› / $.
Press the numeric button of the desired track. The
previously programmed track will be cleared from
memory and the new one will be programmed.
Press PEAK while the player is stopped or the tray is
opened.
• It takes a few minutes to search for the peak level. When
found, the unit plays the peak level for 4 seconds repeatedly.
To cancel searching
Press &.
To delete all program data
When program play is stopped, press &.
E-22
ADD KX-E100 AND/OR MDX-E100 TO YOUR SYSTEM
English
Operating the cassette deck, KX-E100 and MD
recorder, MDX-E100 with the remote control
MDX-E100
DISP
SLEEP
TIME
A
REP
RNDM
D
C
PROG
B
PEAK
E
TAPE
,
FREQ PS/PTY/RT/CT
PTY SEEK
MODE
KX-E100
START
VOLUME
AUX
1
2
3
4
5
6
POWER
TAPE input
TAPE REC/PAUSE
@# (Tape Direction)
$/! (Rewind/Music Search Backward)
›/⁄ (Fast Forward/Music Search Fast
Forward)
7 & (Stop)
8 ^ (Play)**
*
TAPE
MD
CD
TUNER
MD REC
~ TIME (Same function as DISPLAY on
MDX-E100 remote control)
Ÿ REP (Repeat)
! PROG (Program)
⁄ RNDM (Random)
@ POWER
¤ Numeric buttons
# MD input
‹ MD REC/PAUSE
$ $/! (Skip/Search Backward)
› ›/⁄ (Skip/Search Forward)
% & (Stop)
fi ^ (Play/Pause)
PRESET
PTY SELECT
TAPE REC
TAPE
,
,
,
* Input selectors when recording.
**There is no pause function on KX-E100.
,
MODE
START
DUBBING
E-23
ADD KX-E100 AND/OR MDX-E100 TO YOUR SYSTEM
2
Before recording
When you record by using MDX-E100 or KX-E100, you
must first make the connections as shown in “Connecting
the system” on page 5. For details, refer to the instructions
supplied with the MDX-E100 or KX-E100. A source from
the component which is connected to the AUX terminal
component can be recorded on a tape or MD.
• Only the first track is recorded. After recording the
CD tray opens automatically.
3
Dubbing setting
4
There are six different combinations of components. Once
you choose a certain mode, recording starts and ends
automatically in a certain way for each mode.
MD REC
• Same as CD (Tr1) = TAPE
TAPE REC
TAPE
5
DUBBING
MODE
MODE
START
DUBBING
DUBBING
START
Record unit
• Same as CD = TAPE
6
1
Play unit
Play unit
Record unit
Decide the combination of the components. Each
time you press DUBBING MODE, the mode will
change in the below order.
• Recording automatically starts at the beginning of
the tape. (By pressing DUBBING START, the
tape automatically rewinds to the beginning if it is
in the middle.)
1
• Recording automatically starts from the beginning
of the tape. (By pressing DUBBING START, the
tape automatically rewinds to the beginning if it is
in the middle.)
• When the recording on side A finishes while a
track is being played back, the recording on side B
starts from the beginning of the same track.
• The sound is automatically faded out when it gets
close to the end of side B.
E-24
2
Press DUBBING START to start recording.
Note
• The displays 1~6 which include the component you have not
connected to your receiver (RX-E100) will be skipped.
ADD KX-E100 AND/OR MDX-E100 TO YOUR SYSTEM
By specifying the length of the tape, the CD player,
CDX-E100 programs tracks or helps you to program
tracks so they will fit onto the tape with the least amount
of unrecorded space remaining at each end of the tape.
There are three ways of programming.
1 Manual TAPE programming
Press PROG to start programming.
• “A
B” appears in the display to indicate the direction
of the tape.
4
Select the desired track number using numeric
buttons.
• Repeat step 4 to continue programming tracks.
• The remaining time is shown on the display. If the track is
longer than the remaining time, “Error” appears on the
display.
5
Press TAPE to continue programming tracks on side
B.
• Repeat step 4.
SLEEP
DISP
TIME
A
REP
RNDM
REP
C
PROG
PROG
B
RNDM
D
PEAK
TAPE
TAPE
FREQ PS/PTY/RT/CT
6
Press PROG to confirm the program.
7
Choose CD = TAPE by pressing DUBBING
MODE, and press DUBBING START to start
recording.
E
2 Automatic TAPE programming
PTY SEEK
MODE
START
VOLUME
TAPE
MD
AUX
TUNER
MD REC
PRESET
PTY SELECT
1
Repeat steps 1 and 2 of “Manual TAPE
programming”.
2
Press REP to start programming.
CD
• Programming is done in the order on the CD from side A
to side B. When complete, the programmed track number
and total time are indicated in the display for 3 seconds.
TAPE REC
TAPE
DUBBING
MODE
MODE
DUBBING
START
START
DUBBING
1
Insert the desired disc into the CD player, and load a
blank tape into the KX-E100.
2
Press TAPE repeatedly to select the length of tape to
be used. Each time you press TAPE, the length of the
tape changes as follows:
46
3
Press PROG to confirm the program.
4
Choose CD = TAPE by pressing DUBBING
MODE, and press DUBBING START to start
recording.
3 Random TAPE programming
1
Repeat steps 1 and 2 of “Manual TAPE
programming”.
2
Press RNDM to start programming.
• Programming of CD tracks is done randomly from side A
to side B. When complete, the programmed track number
and total time are indicated in the display for 3 seconds.
54
90
60
• You can use numeric buttons to input the length of the
tape.
3
Press PROG to confirm the program.
4
Choose CD = TAPE by pressing DUBBING
MODE, and press DUBBING START to start
recording.
E-25
English
TAPE Programming
3
ADDITIONAL INFORMATION
CD preventive care
• This compact disc player is designed for playing
compact discs bearing the
or
mark only. Never
attempt to load any other type of disc into the unit.
The unit will also play 8-cm (3-inch) compact discs.
• Compact discs are not affected by small particles of
dust or fingerprints on their playing surface, but even so
they should be kept clean. Wipe by using a clean, dry
cloth. Do not wipe with a circular motion; wipe straight
outward from the center.
,,,
,,
,,,
,,
,, ,,,
,,,
• Compact discs are not subjected to wear during play,
but damage to the disc surface when the disc is being
handled can adversely affect the disc’s play.
• Do not use cleaning discs or warped discs. All of these
could damage the unit.
To prevent a malfunction of this unit
• Do not use any non standard shaped CD (heart, etc.)
available on the market, because it may damage the
unit.
• Do not try to clean the disc’s surface by using any type
of disc cleaner, record spray, antistatic spray or liquid,
or any other chemical-based liquid, because such
substances might irreparably damage the disc’s surface.
• Do not expose discs to direct sunlight, high temperature
or high humidity for a long period of time, because
these might warp or otherwise damage the disc.
• Do not use a CD with tape, seals, or paste on it, because
damage to the unit may result.
No!
Troubleshooting
RX-E100 RECEIVER
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the
simple measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the
power cord and contact your authorized YAMAHA dealer or service center for help. When taking the service, the
MDX-E100 or KX-E100 may be needed. For details, contact your authorized YAMAHA dealer or service center.
E-26
SYMPTOM
CAUSE
REMEDY
The unit does not switch ON when
the STANDBY/ON switch is pressed.
The AC power cord is not connected or not
completely connected.
Securely connect the power cord.
No sound from one speaker.
Loose speaker connections.
Connect properly.
No sound from speakers.
Internal protection circuit is functioning.
Unplug the AC power cord from the wall outlet, and
then plug in again.
No sound from an external unit
connected with this unit or play does
not begin.
Incorrect cord connections.
Connect the cords properly. If the problem persists,
the cords may be defective.
Input source selection is not proper.
Make a proper input source selection.
ADDITIONAL INFORMATION
CAUSE
REMEDY
Excessive static in FM broadcasts.
Interference from starting motor of a nearby
car.
Position the FM antenna as high and as far away
from nearby roads as possible. Connect using a
coaxial cable.
Interference from the thermostat of a nearby
electrical appliance.
RX-E100 RECEIVER
Noise increases during stereo
broadcasts.
Antenna input is too weak due to obstructions
or excessive distance from the broadcasting
station.
Check the antenna connection.
Stereo broadcasts are noisy and
STEREO indicator blinks on and off.
Insufficient antenna input.
Install an antenna appropriate for the electric field
strength of your area.
Cannot select preset stations.
Preset memory has been erased.
Reprogram memory presets.
Buzzing or static during AM
broadcasts.
Interference from sources such as lightning,
fluorescent lights, electric motors or
thermostat of nearby electrical appliance.
The problem is difficult to eliminate, but can be
lessened by grounding AM loop antenna.
TV or microprocessor is being used nearby.
Move away from TV or microprocessor.
Radio signal is weak or the antenna is not
properly connected.
Properly connect the AM loop antenna.
AM broadcast sensitivity is poor.
Install a multi-element type FM antenna if possible.
Change orientation of the AM loop antenna.
REMOTE CONTROL
CDX-E100 CD PLAYER
Install an external AM loop antenna.
Cannot set timer.
Current time is not set.
Set current time.
The unit does not work normally.
The internal microcomputer has been frozen
by an external electric shock (lightning,
excessive static electricity, etc.) or the power
supply with low voltage.
Unplug the AC power cord from the wall outlet, and
then plug in again after about one minute.
Play does not begin.
The disc is damaged.
Check the disc carefully; replace it if necessary.
There is moisture on the laser pick-up.
Wait 20 to 30 minutes after switching the unit ON
before trying to play a disc.
The disc has been loaded upside down.
Reload the disc with the label side facing up.
The disc is dirty.
Clean the disc.
Play is delayed, or begins at the
wrong place.
The disc may be scratched or damaged.
Check the disc carefully; replace it if necessary.
CD synchronized recording or
Automatic recording function does
not work.
The system cable is not connected securely.
Connect the system cable properly.
Sound “skips.”
The unit is being subjected to vibrations or
impacts.
Relocate the unit.
The disc is dirty.
Clean the disc.
Sound “hums.”
Improper cable connections.
Securely connect the audio cables. If the problem
persists, the cables may be defective.
Noise from inside of the unit.
The disc may be warped.
Replace the disc.
The remote control does not work.
The batteries of the remote control are too
weak.
Replace the batteries with new ones.
Remote control is too far away or is being
used at an incorrect angle.
Use within 6 meters and 60 degree radius.
Direct sunlight or lighting (of an inverter type
of fluorescent lamp, etc.) is striking the
remote control sensor of the unit.
Change the position of the unit.
Remote control is being used near TV set
with a remote control sensor.
Relocate this unit away from the TV or cover the
TV’s remote control sensor.
TV functions strangely when the
remote control is being used.
E-27
English
SYMPTOM
ADDITIONAL INFORMATION
Specifications
<RX-E100>
<CDX-E100>
Amplifier section
CD player section
Minimum RMS output power per channel
.............................................. 50 W + 50 W (6Ω 1kHz 0.07% THD)
.................................. 40 W + 40 W (6Ω 20 - 20,000Hz 0.1% THD)
DIN Standard output power per channel (Europe model)
................................................ 60 W + 60 W (4Ω 1kHz 0.7% THD)
Input sensitivity/Impedance
CD/TAPE/MD/AUX
............................................................................ 150 mV/47 k-ohms
D/A converter
.......................................................................................... S-bit DAC
Frequency response (2 – 20,000 Hz)
............................................................................................. ±0.5 dB
S/N ratio
............................................................................................... 102 dB
Tuner section
Tuning range
FM
[U.S.A. and Canada models]
.............................................................................. 87.5 – 107.9 MHz
[U.K., Europe, Australia, and General models]
.......................................................................... 87.50 – 108.00 MHz
AM
[U.S.A. and Canada models]
................................................................................. 530 – 1710 kHz
[U.K., Europe, and Australia models]
................................................................................. 531 – 1611 kHz
[General model]
................................................................. 530/531 – 1710/1611 kHz
Sensitivity
FM (S/N 30dB)
................................................................................................ 1.5 µV
FM (S/N 26dB) (DIN)
................................................................................................ 1.8 µV
AM
.......................................................................................... 300 µV/m
General
Power supply
[U.S.A. and Canada models]
............................................................................... AC 120 V, 60 Hz
[Australia model]
............................................................................... AC 240 V, 50 Hz
[U.K. and Europe models]
............................................................................... AC 230 V, 50 Hz
[General model]
.................................................... AC 110/120/220/240 V, 50/60 Hz
Power consumption
[U.S.A. and Canada models]
................................................................................................ 110 W
[U.K., Europe, Australia, and General models]
................................................................................................ 100 W
Dimensions (W x H x D)
.......................................................................... 217 x 108 x 312 mm
Weight
................................................................................................. 4.5 kg
Accessories
.................................................................................. Remote control
Batteries
Indoor FM antenna
AM loop antenna
E-28
Laser Diode Properties
•
•
•
•
Material: GaAIAs
Wavelength: 780 nm
Emission duration: continuous
Laser output: max. 44.6 µW*
* This output is the value measured at a distance of about 200 mm
from the objective lens surface on the Optical Pick-up Block.
General
Power supply
[U.S.A. and Canada models]
............................................................................... AC 120 V, 60 Hz
[Australia model]
............................................................................... AC 240 V, 50 Hz
[U.K. and Europe models]
............................................................................... AC 230 V, 50 Hz
[General model]
.................................................... AC 110/120/220/240 V, 50/60 Hz
Power consumption
.................................................................................................. 13 W
Dimensions (W x H x D)
.......................................................................... 217 x 108 x 290 mm
Weight
................................................................................................. 3.0 kg
Accessories
................................................................................... RCA pin cable
System control cable
Specifications are subject to change without notice.
AANVULLENDE INFORMATIE
Technische gegevens
<RX-E100>
<CDX-E100>
Versterkergedeelte
CD-speler gedeelte
Minimaal RMS uitgangsvermogen per kanaal
........................................ 50 W + 50 W (6 Ohm 1kHz 0,07% THD)
............................ 40 W + 40 W (6 Ohm 20 - 20.000Hz 0,1% THD)
DIN standaard uitgangsvermogen per kanaal (Modellen voor Europa)
.......................................... 60 W + 60 W (4 Ohm 1kHz 0,7% THD)
Ingangsgevoeligheid/Impedantie
CD/TAPE/MD/AUX
.......................................................................... 150 mV/47 kiloOhm
D/A converter
.......................................................................................... S-bit DAC
Frequentierespons (2 - 20.000 Hz)
............................................................................................. ±0,5 dB
S/R verhouding
............................................................................................... 102 dB
Tunergedeelte
Afstembereik
FM
[Modellen voor U.S.A. en Canada]
.............................................................................. 87,5 – 107,9 MHz
[Modellen voor Groot-Brittannië, Europa, Australië en algemene
modellen]
.......................................................................... 87,50 – 108,00 MHz
AM
[Modellen voor U.S.A. en Canada]
................................................................................. 530 – 1710 kHz
[Modellen voor Groot-Brittannië, Europa en Australië]
................................................................................. 531 – 1611 kHz
[Algemene modellen]
................................................................. 530/531 – 1710/1611 kHz
Gevoeligheid
FM (S/R 30 dB)
.................................................................................... 1,5 microWatt
FM (S/R 26 dB) (DIN)
.................................................................................... 1,8 microWatt
AM
............................................................................... 300 microWatt/m
Algemeen
Stroomvoorziening
[Modellen voor U.S.A. en Canada]
............................................... 120 VIEWCAM wisselstroom, 60 Hz
[Modellen voor Australië]
............................................... 240 VIEWCAM wisselstroom, 50 Hz
[Modellen voor Groot-Brittannië en Europa]
............................................... 230 VIEWCAM wisselstroom, 50 Hz
[Algemene modellen]
.................... 110/120/220/240 VIEWCAM wisselstroom, 50/60 Hz
Stroomverbruik
[Modellen voor U.S.A. en Canada]
................................................................................................ 110 W
[Modellen voor Groot-Brittannië, Europa, Australië en algemene
modellen]
................................................................................................ 100 W
Afmetingen (B x H x D)
.......................................................................... 217 x 108 x 312 mm
Gewicht
................................................................................................. 4,5 kg
Accessoires
.............................................................................. Afstandbediening
Batterijen
FM binnenantenne
AM ringantenne
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
Eingenschappen laserdiode
•
•
•
•
Materiaal: GaAIAs
Golflengte: 780 nm
Emissieduur: continu
Laser uitgangsvermogen: max. 44,6 microWatt*
* Dit uitgangsvermogen is de waarde op ongeveer 200 mm afstand
van het oppervlak van de lens op het Optische pick-up blok.
Algemeen
Stroomvoorziening
[Modellen voor U.S.A. en Canada]
............................................... 120 VIEWCAM wisselstroom, 60 Hz
[Modellen voor Australië]
............................................... 240 VIEWCAM wisselstroom, 50 Hz
[Modellen voor Groot-Brittannië en Europa]
............................................... 230 VIEWCAM wisselstroom, 50 Hz
[Algemene modellen]
.................... 110/120/220/240 VIEWCAM wisselstroom, 50/60 Hz
Stroomverbruik
.................................................................................................. 13 W
Afmetingen (B x H x D)
.......................................................................... 217 x 108 x 290 mm
Gewicht
................................................................................................. 3,0 kg
Accessoires
.................................................................... RCA (tulpstekker) kabel
Systeembedieningskabel
Technische gegevens kunnen zonder voorafgaande berichtgeving
gewijzigd worden.
ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in Malaysia
V423480
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising