Topfield SBP-2000 User guide

TOPFIELD
SBP-2000
User Guide
High Definition
Digital Satellite Receiver
USB PVR-Ready
Common Interface
ii
CONTENTS
Contents
Contents
1
2
3
Introduction
1.1 Features . . . . . . . . . . . . .
1.2 Controlling the digital receiver .
1.2.1 Front panel . . . . . . .
1.2.2 Remote control . . . . .
1.3 Common Interface . . . . . . . .
ii
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
1
1
2
3
4
6
Setup
2.1 Unpacking . . . . . . . . . . . . . . . . . .
2.2 Safety precautions . . . . . . . . . . . . . .
2.3 Rear panel connections . . . . . . . . . . .
2.4 Connecting up your digital receiver . . . .
2.4.1 Connecting to the antenna . . . . .
2.4.2 Connecting to your television set .
2.4.3 Connecting to your video recorder
2.5 Switching on for the first time . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
8
8
8
10
11
12
12
15
15
Service Search
3.1 Searching for broadcasting services . . .
3.1.1 Configuring LNB settings . . . .
3.1.2 Configuring DiSEqC 1.2 settings
3.1.3 Configuring USALS settings . . .
3.1.4 Searching for services . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
17
17
18
20
21
22
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
CONTENTS iii
3.2
3.3
3.4
4
5
Editing the transponder list . . . . . . . . . . . . . . . . . . .
Resetting to factory settings . . . . . . . . . . . . . . . . . . .
Resetting to user settings . . . . . . . . . . . . . . . . . . . . .
Preference Settings
4.1 Language settings . . . . . . . . .
4.1.1 Menu language . . . . . .
4.1.2 Subtitle language . . . . .
4.1.3 Hard of Hearing . . . . .
4.1.4 Audio language . . . . . .
4.2 Video and audio settings . . . . .
4.2.1 High definition television
4.2.2 Television aspect ratio . .
4.2.3 Colour format . . . . . . .
4.2.4 Another video device . . .
4.2.5 Audio mode . . . . . . . .
4.3 Local time setting . . . . . . . . .
4.4 Parental control . . . . . . . . . .
4.5 Options for recording . . . . . . .
4.6 Options for playback . . . . . . .
4.7 Options for on-screen display . .
4.8 Options for standby mode . . . .
26
27
27
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
30
30
30
31
31
31
32
32
33
34
34
35
35
38
39
40
41
42
Every Day Use
5.1 Volume control . . . . . . . . . . . . . .
5.2 Watching television . . . . . . . . . . . .
5.2.1 The services list . . . . . . . . . .
5.2.2 The favourite service lists . . . .
5.2.3 Viewing programme information
5.2.4 Selecting audio tracks . . . . . .
5.2.5 Selecting subtitle tracks . . . . .
5.2.6 Viewing teletext . . . . . . . . . .
5.3 Viewing electronic programme guide . .
5.4 Watching multifeed programme . . . . .
5.5 Using time-shift . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
43
43
43
43
46
47
48
48
48
49
50
50
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
iv
CONTENTS
6
Organising Services
6.1 Editing the services list . . . . . . . . . . . . . . . . . . . . . .
6.2 Editing the favourite lists . . . . . . . . . . . . . . . . . . . . .
6.3 How to use on-screen keyboard . . . . . . . . . . . . . . . . .
52
52
54
56
7
Recording and Playback
7.1 Recording a programme . . . . . . . . . . . . . . . . . . . .
7.1.1 Instant recording . . . . . . . . . . . . . . . . . . . .
7.1.2 Timer recording . . . . . . . . . . . . . . . . . . . . .
7.1.3 Scheduling recordings using the programme guide .
7.1.4 Recording a pay service programme . . . . . . . . .
7.2 File archive . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.1 To delete a recording . . . . . . . . . . . . . . . . . .
7.2.2 To sort recordings . . . . . . . . . . . . . . . . . . . .
7.2.3 To lock a recording . . . . . . . . . . . . . . . . . . .
7.2.4 To rename a recording . . . . . . . . . . . . . . . . .
7.2.5 To make a new folder . . . . . . . . . . . . . . . . . .
7.2.6 To move a recording to another folder . . . . . . . .
7.3 Playing back a recording . . . . . . . . . . . . . . . . . . . .
7.3.1 To navigate using the progress bar . . . . . . . . . .
7.3.2 To play in slow motion . . . . . . . . . . . . . . . . .
7.3.3 To play in fast motion . . . . . . . . . . . . . . . . . .
7.3.4 To make a bookmark . . . . . . . . . . . . . . . . . .
7.3.5 To play back a recording repeatedly . . . . . . . . .
7.3.6 To play back recordings in sequence . . . . . . . . .
7.3.7 To play back a scrambled recording . . . . . . . . . .
7.4 Playing back a video file . . . . . . . . . . . . . . . . . . . .
7.5 Formatting the hard disk . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
57
57
58
59
62
62
63
64
64
64
64
65
65
65
66
66
66
67
67
68
68
69
70
Firmware Update
8.1 From a memory stick . . . . . . . . . . . . . . . . . . . . . . .
8.2 Over the air . . . . . . . . . . . . . . . . . . . . . . . . . . . .
71
71
72
8
1
Chapter 1
Introduction
The SBP-2000 digital receiver is fully compliant with the international Digital Video Broadcasting (DVB) standard, and thus
is able to receive digital broadcasts of that standard. For its
operation you need an antenna, which must be installed appropriately.
NOTE
In general we equate a channel with a frequency. However,
unlike analogue broadcasts, digital broadcasts are not all
assigned to their own frequencies; instead, multiple television broadcasts are transmitted through a single frequency.
The frequency in digital broadcasting is usually called transponder or multiplex. To reduce confusion in this manual,
the word service is preferably used than channel as a term
to indicate one television or radio broadcast.
1.1
Features
This digital receiver has the following features:
• Supports DiSEqC 1.0, DiSEqC 1.1, DiSEqC 1.2 and USALS protocols.
2
Introduction
• Can store up to 10,000 television and radio services.
• You can edit the services list.
• Can create lists of your favourite services.
• Can view information about the current television or radio programme.
• Has an electronic programme guide that provides an
overview of scheduled programmes.
• Time-shift is a special technical feature available on this
digital receiver. You can pause a programme you are
watching and resume it again at a later time. Then you
can quickly go to any part of the current programme by
fast forward or rewind search.
• If you have an external hard drive connected to the digital receiver via the USB port, you can record television
programmes into it.
• You can play back video files of various formats including DivX.
1.2
Controlling the digital receiver
You can operate the digital receiver with the remote control or
the buttons on the front panel.
NOTE
When the digital receiver is off but plugged into a wall
socket, we say that it is in standby mode; on the other hand,
when it is on, it is in active mode. Even when you are not
using the digital receiver, you should keep it plugged into
a wall socket to be in standby mode so that it can run timer
events at any time.
1.2 Controlling the digital receiver 3
1.2.1
Front panel
The front panel of the digital receiver has buttons to control
the digital receiver, specific lights and a display to indicate its
status. The following indicates what they mean.
button switches the digital receiver between standby mode
and active mode.
ca
CHANNEL ,
buttons switch to the previous or next service. They are also used to navigate in menus and interactive screens.
light blinks every time you press a button on the remote
control.
STANDBY light lights up while the digital receiver is in standby
mode.
Front display shows the current time in standby mode, and
displays the current service in active mode.
There is a USB port on the front panel for
firmware update and data transfer. If you
have an external hard drive connected to the
digital receiver via the USB port, you can
record television programmes into it.
4
Introduction
1.2.2
Remote control
..
1
.
1
14
15
4
18
16
..
2
.
7
..
3
.
6
10
12
11
2
13
20
5
17
..
4
..
5
.
3
8
21
33
5
9
34
32
35
27
26
22
23
36
25
28
29
24
31
19
30
is used to set a sleep timer in
10 minute increments.
V− , V+ buttons decrease or increase the volume. They are also
used to change values for menu
options.
.
3
button switches the digital
receiver between standby mode
and active mode.
mutes the sound. Press again
to switch it back on.
P− , P+ buttons switch to the
previous or next service. They are
also used to navigate in menus
and interactive screens.
..
6
.
..
7
.
..
8
.
switches over between the
current service and the previously viewed one.
Numeric buttons are used to enter a service number for service
change or to specify values for
menu options.
OK displays the services list. See
§5.2.1 for more details. It is also
used to select a menu item.
.. 9 FAV displays the favourite lists.
..
displays the service informa10
tion box. It is also used to display more information about a
programme.
.
.
1.2 Controlling the digital receiver 5
..
11
.
is used to select an audio track and a sound mode, or
a video track of multifeed programme.
..
is used to select a subtitle track.
12
..
displays teletext.
13
.. 14 V.Format changes video resolution. See §4.2.1 for more de.
.
.
tails.
.. 15 A/R changes aspect ratio. See §4.2.2 for more details.
..
switches over between television services and radio
16
.
.
services.
..
17
..
18
.
.
GUIDE displays the electronic programme guide.
AUX switches the output of the TV SCART socket over between the digital receiver and the device connected to the
VCR SCART socket. See §4.2.4 for more details.
..
19
..
20
.
.
SAT displays the satellites list with their services list.
MENU displays the main menu. It is also used to return to
the previous menu from a submenu.
.. 21 EXIT is used to exit a menu or to hide on-screen informa.
tion.
..
22
..
23
.
.
..
24
.
..
25
.
is used to start recording.
is used to stop playback, to stop recording, or to jump
back to live television from time-shifted television.
is used to display the list of recorded programmes that
are stored in the external hard drive. See §7.2 for more
details.
resumes normal playback speed, or displays the
progress bar for navigation on playback or time-shift. To
..
play a recorded programme, see button 24
.
.
..
26
.
..
27
.
pauses live television or playback of a recorded programme.
is used to start reverse playback. Subsequent presses
increase the rewind speed.
6
Introduction
..
28
.
..
29
.
..
30
.
..
31
..
32
..
33
..
34
..
35
..
36
is used to start fast forward playback. Subsequent
presses increase the playback speed.
is used to start slow motion playback. Subsequent
presses change the playback speed.
is used to jump back to the beginning of the recording
on playback.
is used to jump to the end of the recording on playback.
.
has different functions per menu.
.
.
.
.
is used to make a bookmark on playback or time-shift.
is used to jump to next bookmark position.
has different functions per menu.
has different functions per menu.
.
How to use the colour buttons will be guided by the on-screen
help.
NOTE
When using the remote control, point it at the remote sensor
on the front panel of the digital receiver.
1.3
Common Interface
There are pay TV services available; these
are accessible with the use of a Conditional
Access Module (CAM) and a subscription
card. A Common Interface (CI) is the slot
into which you can insert a CAM. The front
of the digital receiver has two common interface slots. To watch a pay service, you should
take the following steps:
1. Purchase a CAM and a subscription card for the pay service you want to watch.
2. Insert the subscription card into the CAM.
1.3 Common Interface
7
3. Insert the CAM into a common interface on the front of
the digital receiver.
To view the information about
the module and subscription
card which is inserted into the
digital receiver, select the Information > Common Interface
menu.
8
Setup
Chapter 2
Setup
2.1
Unpacking
Before going any further, check that you have received the following items with the digital receiver.
•
•
•
•
Remote control unit
Two batteries for the remote control (AAA 1.5 V)
One Component cable (RCA cable)
A copy of this user guide
NOTE
Accessories may vary according to your local area.
2.2
Safety precautions
Please read carefully the following safety precautions.
• The mains voltage must range between 90 and 250 volts.
Check it before plugging the digital receiver to the wall
socket. For the power consumption of the digital receiver, refer to Table 2.1.
2.2 Safety precautions
9
• The wall socket should be near the equipment. Do not
run an extension lead to the unit.
• The mains plug shall remain readily operable so that it
can be removed easily to disconnect the power.
• The digital receiver shall not be exposed to dripping or
splashing water, and no objects filled with liquids, such
as vases, shall be placed on it.
• Do not expose the digital receiver to any moisture. The
digital receiver is designed for indoor use only. Use dry
cloth to clean the digital receiver.
• Place the digital receiver on a firm and level surface.
• Do not place the digital receiver close to heat emitting
units or in direct sunlight, as this will impair cooling.
Do not lay any objects such as magazines on the digital receiver. When placed in a cabinet, make sure there
is a minimum space of 10 centimetres around it. For the
physical specification of the digital receiver, refer to Table 2.2.
• Protect the power cord from being walked on or pinched.
If the cord is damaged, do not use the digital receiver and
get the cord replaced.
• Never open the digital receiver casing under any circumstances, or the warranty will be void.
• Refer all servicing to a qualified service technician.
Table 2.1: Power specification
Input voltage
Power consumption
90 to 250 V AC, 50/60 Hz
35 W at maximum in active
Under 1 W in passive standby
10
Setup
Table 2.2: Physical specifications
Size
Weight
Operating temperature
Storage relative humidity
2.3
260× 46× 190 mm
1.2 kg
0 to 45 ◦C
5 to 90 %
Rear panel connections
The SBP-2000 has the following connections on the back:
Check what connections your television set has in comparison
with the digital receiver.
..
1 LNB IN
.
..
2 LNB OUT
.
..
3 VCR
.
..
4 TV
.
..
5 Y/Pb/Pr
.
Satellite broadcasting signal input socket
(Current: Max.500mA with overload protection)
Satellite broadcasting signal output socket
through the LNB IN socket for another digital receiver
Audio and video input/output socket for
another device such as a video recorder
Audio and video output socket for the television set
Component video output socket for the television set (green/blue/red)
2.4 Connecting up your digital receiver 11
..
6 AUDIO L/R Stereo audio output socket for the television set or the audio-video receiver (white/red)
..
Composite video output socket for the tele7 VIDEO
.
.
vision set (yellow)
..
8 S/PDIF
.
..
9 HDMI
.
Digital audio output socket for the audiovideo receiver
Audio and video output socket for the high
definition television set
Table 2.3: Connectors specifications
HDMI
TV
VCR
YPbPr
VIDEO
AUDIO
S/PDIF
USB
2.4
High definition video output
Left & right audio output
Digital audio output
CVBS/S-Video/RGB video output
Left & right audio output
CVBS video output
Left & right audio output
CVBS/S-Video/RGB/YUV video input for bypass
Left & right audio input for bypass
Component video output
Composite video (CVBS) output
Left & right audio output
Digital audio output
2.0 Host 5 V DC, 500 mA (on the front)
Connecting up your digital receiver
There are several ways to set up the digital receiver. Set up the
digital receiver suitably to your television and other devices.
If you have any problem with your setup or need help, contact
your dealer.
12
Setup
2.4.1
Connecting to the antenna
Whatever sort of connection you have between
the digital receiver and the television, you need
to connect the digital receiver to the antenna so
that it can receive digital television broadcasts.
Connect the antenna cable to the LNB IN connector.
NOTE
Perhaps you are expecting that the satellite antenna could
simultaneously catch all frequencies coming from a satellite
and send them to the digital receiver. However, the satellite
antenna only sends the frequencies that it can catch with the
LNB frequency and polarisation specified by the digital receiver. So if you have another digital receiver linked from
the LNB OUT connector, you can only use it limitedly. See
§3.1 for more details.
2.4.2
Connecting to your television set
For all the following connections of the digital receiver, we recommend you to use the first connector to get the best picture
quality. If your television does not have a matching connector,
then use the next connector in the following order for a better
picture quality.
1.
2.
3.
4.
HDMI connector (HDMI)
Component connector (YPbPr)
SCART connector (TV)
Composite connector (VIDEO)
You should configure audio and video settings after connecting up the digital receiver. See §4.2 for a detailed description.
2.4 Connecting up your digital receiver 13
To use the HDMI output
If you have a high definition television set,
you should use an HDMI cable for best results. Plug one end of the cable into the HDMI
socket on the digital receiver, and plug the
other end into the matching socket on your
television. In this case, you do not have to
make audio connection because it can output
stereo audio or digital audio as well.
To use the SCART output
For best results with a standard television set,
you should use a SCART cable. Plug one end
of the cable into the TV socket on the digital
receiver, and plug the other end into a free
SCART socket on your television.
If you connect with a standard SCART cable, you do not have
to make audio connection because it can output stereo audio
as well. But if you use a conversion cable such as SCART-toComponent, then you have to make audio connection.
NOTE
You cannot view high definition video by means of the
SCART output.
To use the Component video output
You need to obtain a Component video cable (RCA cable) to use the Component video
output. Plug one ends of the cable into the Y
(green), Pb (blue) and Pr (red) sockets on the
digital receiver, and plug the other ends into
the matching sockets on your television.
14
Setup
NOTE
When connecting with the Component video cable, remember to also plug in the additional white and red audio cables
from the digital receiver to the back of your television.
To use the Composite video output
You need to obtain a Composite video cable
(RCA cable) to use the Composite video output. Plug one end of the cable into the VIDEO
(yellow) socket on the digital receiver, and
plug the other end into the matching socket
on your television.
NOTE
You cannot view high definition video by means of the Composite video output.
To make the audio connection
You need to obtain an audio cable (RCA cable) to link the audio connectors. Plug one
ends of the cable into the AUDIO L (white)
and AUDIO R (red) sockets on the digital receiver, and plug the other ends into
the matching sockets on your television or
audio-video receiver.
2.5 Switching on for the first time
15
To enjoy Dolby Digital audio, your television
or audio-video receiver must be able to decode Dolby Digital audio, and you need to
obtain an S/PDIF cable.
Plug one end of the cable into the S/PDIF
socket on the digital receiver, and plug the
other end into the matching socket on your
audio-video receiver.
2.4.3
Connecting to your video recorder
The digital receiver can also output video through an auxiliary
SCART connector to another device such as a video recorder.
You need to obtain a SCART cable to link the
auxiliary SCART connector. Plug one end
of the cable into the VCR socket on the digital receiver, and plug the other end into the
matching socket on your video recorder or
suchlike.
2.5
Switching on for the first time
Now that you have your digital receiver connected, you should
plug it into a wall socket. Ensure that your television set is
turned on and on the correct video channel so that you will be
able to see the display from the digital receiver.
Before switching on the digital receiver, you should insert batteries into the remote control. Open the battery compartment
by removing the lid, and then insert the batteries observing the
polarity, which is marked on the base of the battery compartment.
Press the
button on the top left corner on the remote control. In a little time, you may see a picture displaying a menu.
If you do not see a picture, try pressing the V.Format button on
the remote control. If after several tries you still get no picture,
16
Setup
check that the television is set to the correct input. If the picture
is good, you can skip to §3.1 to search for available television
and radio services. Otherwise, you may need to temporarily
connect the Composite video connector (VIDEO) to your television set so that you can see the menu in order to configure
the video settings.
CAUTION
If the digital receiver no longer reacts properly to the remote
control commands, the batteries may be flat. Be sure to replace only with 1.5 V AAA size batteries, and observe the
following precautions.
• Do not mix different types of batteries, or new and old
batteries.
• Do not use rechargeable batteries.
• Do not recharge the old batteries.
• In order to avoid any risk of explosion, observe the polarities indicated inside the battery compartment.
• Do not subject to excessive heat such as the sun and
fire.
• If you are not using the remote control for a long period of time, remove the batteries. The manufacturer
accepts no liability for the damage resulting from leaking batteries.
• Batteries, including those which contain no heavy
metals, may not be disposed with other household
wastes. Please dispose of used batteries in an environmentally sound manner. Find out the legal regulations
which apply in your area.
17
Chapter 3
Service Search
After connecting up the digital receiver, you will need to perform a service search.
NOTE
If there is no service stored, you will be not able to access all
menus. A  is another name for a .
3.1
Searching for broadcasting services
This digital receiver can be operated with both fixed antenna
and motorized antenna. You have to configure antenna settings according to your antenna system in the following order:
1. Configure LNB settings. Refer to §3.1.1.
2. Set the position of your desired satellites if you have a
motorized antenna. You can control the antenna in DiSEqC 1.2 mode or USALS mode. Refer to §3.1.2 for DiSEqC 1.2, and refer to §3.1.3 for USALS.
3. Perform a service search.
18
Service Search
3.1.1
Configuring LNB settings
There are two large frequency bands for satellite broadcasts.
One is C band which ranges approximately from 4 to 6 GHz.
The other is Ku band which ranges approximately from 12 to
18 GHz.
The LNB (Low Noise Block converter)
is used to take a wide band of relatively high frequencies, amplify and
convert them to similar signals that
is carried at a much lower frequency,
which is called Intermediate Frequency
(IF). High frequencies from satellites
are converted into 950 to 2150 MHz by
a LNB.
Select the Installation > LNB
Setting menu to configure the
LNB settings. You should see a
screen like the left figure.
Pressing the OK button on the Satellite Name option displays
the satellite list in alphabetic order. Select the satellite toward
which your antenna is set to face. Even if you cannot find your
desired satellite, you can add your desired satellite to the satellite list. See §3.2 for a detailed description.
The digital receiver has a database of broadcasting satellites
and their transponders, containing the following information:
3.1 Searching for broadcasting services
19
satellite position, frequency range, symbol rate, polarization
and LNB frequency corresponding to the frequency range.
So you might not have to specify the LNB Frequency option.
However, if you have selected the Other entry at the Satellite
Name option to specify a satellite that is not in the satellite list,
you might have to fill in the correct LNB frequency. The absolute difference between a broadcasting frequency and its LNB
frequency must be within 950 to 2150 MHz. For example, if the
frequency band of your desired satellite ranges from 3660 to
4118 MHz, you have to set the LNB Frequency option to 5150
MHz.
The LNB has to be supplied with electric power to operate. Set
the LNB Power option to On if it does not have any other power
supply.
If you use a dual LNB or two antennas which is connected to
the 22 kHz tone switch box, set the 22 kHz option to On.
The digital receiver is designed to be compatible with DiSEqC
(Digital Satellite Equipment Control) switches. It is possible
to connect several antennas to one digital receiver by DiSEqC
switches. A DiSEqC 1.0 switch allows switching between up to
four satellite sources and a DiSEqc 1.1 switch allows switching
between up to 16 satellite sources.
Set the DiSEqC 1.0 option and the DiSEqC 1.1 option according to your antenna configuration.
For example, to select the antenna connected to the A5 input in the left figure, set
the DiSEqC 1.1 option to 2 of 4 and the DiSEqC 1.0 option to 1 of 4. If you have a mini
DiSEqC 1.0 switch which has only two inputs, you should set the DiSEqC 1.0 option
to Mini A instead of 1 of 4.
20
Service Search
3.1.2
Configuring DiSEqC 1.2 settings
Your motorized antenna will turn toward your desired satellites horizontally by DiSEqC 1.2.
When you switch to a service, if it is not
provided by the current satellite, it will take
longer time than usual because the antenna
has to turn to its position.
To use the DiSEqC 1.2 protocol,
select the Installation > Motorized DiSEqC 1.2 menu. You
should see a screen like the left
figure. At first you have to set the
Motorized DiSEqC 1.2 option to
Enable.
To get the correct position of your desired satellite, take the
following steps:
1. Choose your desired satellite at the Satellite Name option.
2. Set the DiSEqC Command Mode option to User.
3. Set the Motor Control option to Goto. Then the antenna
will turn toward your selected satellite by the position
data that the digital receiver has.
4. If the receiving quality, which is displayed at the bottom
right of the screen, is not good, tune the antenna finely
with the Movement option. If you set it to 2(E), the antenna will move to the east by two degrees. At this time
you had better check the receiving quality of every trans-
3.1 Searching for broadcasting services
21
ponder and choose the best one at the Transponder (or
Frequency) option. It will be helpful to your fine tuning.
5. Finally set the Motor Control option to Store to save the
tuned position when the receiving quality is best.
There are more motor control options for installers, but this
guide does not describe them. If you are an installer, refer them
to the manual about the STAB rotor.
3.1.3
Configuring USALS settings
USALS (Universal Satellite Automatic Location System), also
known as DiSEqC 1.3, calculates the positions of all available
satellites from your location. Compared to DiSEqC 1.2, it is
no longer required to manually search and store every satellite
position. Just pointing to a known satellite position is enough.
This position will act as a central point. The USALS will then
calculate positions of visible satellites.
To use the USALS protocol, select the Installation > USALS
Setting menu. You should see
a screen like the left figure. At
first you have to set the Motorized DiSEqC 1.3 option to Enable.
To get every satellite position calculated, take the following
steps:
1. Choose your desired satellite at the Satellite Name option.
2. Enter your location to the My Longitude option and the
My Latitude option with the V− , V+ and numeric buttons.
22
Service Search
3. Enter the position of your selected satellite to the Satellite
Angle option if it is not correct.
4. Select the Goto the position option, then the antenna will
turn toward your selected satellite as calculating its position.
5. If the receiving quality, which is displayed at the bottom
right of the screen, is not good, then tune the antenna
finely with the Move option. The changed position is
automatically saved. At this time you had better check
the receiving quality of every transponder and choose
the best one at the Transponder (or Frequency) option.
It will be helpful to your fine tuning.
3.1.4
Searching for services
To perform a service search, select the Installation > Searching
menu. You should see a screen
like the left figure.
There are in general four service search methods:
•
•
•
•
searching every service of a satellite,
searching every service of a transponder,
searching single service of a transponder,
searching every service of a SMATV (Satellite Master Antenna Television) system.
Searching every service of a satellite
To search every service of a satellite, take the following steps:
3.1 Searching for broadcasting services
23
1. Choose your desired satellite at the Satellite Name option.
2. Set the Search Mode option to Auto.
3. If you set the Network Search option to On, the digital
receiver will check up the up-to-date channel information while searching services, but it takes a rather longer
time.
With the Auto mode, the digital receiver tries to search every
service, relying on the transponder data which is stored at the
time of manufacture. It thus may happen to fail to search all actually available services since services are more often than not
launched, discontinued, or removed into another transponder.
To avoid such missing, you had better set the Search Mode
item to Blind. With the Blind mode, the digital receiver tries
to search every service, scrutinizing every transponder with
every possible combination of transponder elements. It thus
may require many minutes or even many hours.
It is possible to search several satellites one after another for
services. Set the Multi Sat Mode item to Multi, then the Satellite Name item becomes disabled and the Satellite List item be
comes enabled. Pressing the OK button at the Satellite List
item pops up the list of satellites. Select satellites you want
to search and exit with the EXIT button.
Searching every service of a transponder
To search every service of a transponder, take the following
steps:
1. Choose your desired satellite at the Satellite Name option.
2. Set the Search Mode option to Manual, and then press
the OK button to diaply additional options.
3. Choose your desired transponder at the Frequency option or enter it with the numeric buttons.
24
Service Search
4. Enter the symbol rate of your desired transponder to the
Symbol Rate option with the numeric buttons.
5. Set the Polarization option to match to that of your desired transponder.
6. If you set the Network Search option to On, the digital receiver will check up the up-to-date channel information
as searching services, but it takes rather longer time.
7. Set the Modulation option to match to that of your desired transponder. If the transponder is of the DVB-S2
standard, you should set this option to DVB-S2 QPSK or
DVB-S2 8PSK. Then the FEC option and the Pilot option
will become enabled. You also should set these options
correctly.
NOTE
You may get transponder information from a satellite magazine or website such as http://www.satbeams.com or http:
//www.lyngsat.com.
Searching single service of a transponder
To search single service of a transponder, take the following
steps:
1. Choose your desired satellite at the Satellite Name option.
2. Set the Search Mode option to Advanced, and then press
the OK button to diaply additional options.
3. Choose your desired transponder at the Frequency option or enter it with the numeric buttons.
4. Enter the symbol rate of your desired transponder to the
Symbol Rate option with the numeric buttons.
5. Set the Polarization option to match to that of your desired transponder.
3.1 Searching for broadcasting services
25
6. Set the Modulation option to match to that of your desired transponder. If the transponder is of the DVB-S2
standard, you should set this option to DVB-S2 QPSK or
DVB-S2 8PSK. Then the FEC option and the Pilot option
will become enabled. You also should set these options
correctly.
7. At the PID option, specify the audio and video packet
identification (PID) of your desired service with the numeric buttons.
Searching every service of SMATV system
To search every service of a SMATV system, if the digital receiver is connected to it, take the following steps:
1. Choose your desired satellite at the Satellite Name option.
2. Set the Search Mode option to SMATV, and then press
the OK button to diaply additional options.
3. Choose your desired transponder at the Frequency option or enter it with the numeric buttons.
4. Enter the symbol rate of your desired transponder to the
Symbol Rate option with the numeric buttons.
You can search pay services as well as free services as follows:
• To search only free services, set the FTA/Scrambled option to FTA only.
• To search only pay services, set it to CAS only.
• To search both free services and pay services, set it to FTA
+ CAS.
To start service search, move down to the Start Search item,
and press the OK button. The digital receiver will start to
search for services and display a list of television and radio
services as they are found. It is common for no channels to be
found until quite late in the process. When the scan is complete, you will see a message telling you how many services
have been found. Press the OK button to save the list.
26
3.2
Service Search
Editing the transponder list
If you failed to receive services of
a transponder because it consists
of wrong data, you can solve it
by correcting the data. Select the
Installation > SAT/TP Edit menu.
To change the data of a transponder, take the following steps:
1. Choose your desired satellite at the Satellite Name option.
2. Choose your desired transponder at the Frequency option.
3. Change the Polarization option to match to that of your
desired transponder.
4. Set the Modulation option to match to that of your desired transponder. If the transponder is of the DVB-S2
standard, you should set this option to DVB-S2 QPSK or
DVB-S2 8PSK. Then the FEC option and the Pilot option
will become enabled. You also should set these options
correctly.
5. To change a satellite entry’s name, select your desired
entry at the Satellite Name option and select the SAT
Name Edit option. Then the on-screen keyboard appears. Change the name and save it. See §6.3 as to how
to use the on-screen keyboard.
6. Select the Save option and press the OK button to save
the changes. To stop at any time or to exit without saving,
press the EXIT button.
3.3 Resetting to factory settings
3.3
27
Resetting to factory settings
The digital receiver maintains the following data:
•
•
•
•
•
Satellite list
Services list
Favourite list
Timer list
Preference settings
You can reset all data of the digital receiver. Select the Installation > System Recovery > Factory Setting menu, and then
you get asked for confirmation. With the choice of Yes, the
services list, favourite list and timer list will all be cleared, and
preference options will be reset to the manufacturer’s factory
settings.
NOTE
A factory reset will not delete any recorded programmes.
However, you have to search services again after a factory
reset.
3.4
Resetting to user settings
You can store your own data including the following:
•
•
•
•
Satellite list
Services list
Favourite lists
Preference settings
Also you can restore them at any time.
To store your data, select the Installation > System Recovery >
Store System Data menu, then you get asked for confirmation.
If you select Yes, your data will be stored. Whenever you store
your data, they are all overwritten.
To restore your data, select the Installation > System Recovery
> Recover System Data menu, then you get asked for confirmation. With the choice of Yes, your data will be restored.
28
Service Search
You can also store your data to an external storage. To store
your data to an external storage, select the Installation > System Recovery > Export System Data menu, then you get asked
for confirmation. With the choice of Yes, your data will be
stored. Every time you store your data, they are all overwritten.
To restore your data from an external storage, select the Installation > System Recovery > Import System Data menu, then
system data will be listed. Select a data and press the OK button, then your data will be restored.
You can edit the channel data on your computer by using a
channel editor software, Vega, which is available from Topfield’s website, http://www.i-topfield.com/eng/download/
utility_list.asp.
With Vega you can do the following:
• Adding, deleting or modifying satellite entries
3.4 Resetting to user settings
29
• Adding, deleting or modifying transponder entries
• Deleting or modifying service entries
• Adding, deleting or modifying favourite groups
As to how to use Vega, refer to its user guide, which is accompanied by the software.
30
Preference Settings
Chapter 4
Preference Settings
4.1
Language settings
You can select the language in
which the menu will be displayed. In addition to that, you
can select the language of audio
track and of subtitle track. Select
the Settings > Language menu.
You should see a screen like the
left figure.
4.1.1
Menu language
The digital receiver provides menus in several different languages. Set the Menu Language option to your desired language. Once you select a language, the menu will be immediately displayed in the selected language.
4.1 Language settings
4.1.2
31
Subtitle language
Set the 1st Subtitle Language option and the 2nd Subtitle Language option to your desired languages. When you watch a
programme, if the programme has a subtitle track of the language that is specified for the 1st Subtitle Language, it will be
displayed. If the first language is not available but the second
language is available, the subtitle of the second language will
be displayed. If there is no available language, no subtitle will
be displayed.
Apart from this setting, you can select a subtitle track with the
button. See §5.2.5 for a detailed description.
4.1.3
Hard of Hearing
Some broadcasters may send a subtitle track dedicated to the
hard-of-hearing. Even when a subtitle track or more is available, that subtitle track will be displayed prior to those you
have specified for the 1st Subtitle Language and the 2nd Subtitle Language options if the Hard of Hearing option is set to
On.
4.1.4
Audio language
Set the 1st Audio Language option and the 2nd Audio Language option to your desired languages. When you watch a
programme, if the programme has an audio track of the language that is specified for the 1st Audio Language, it will be
output. If the first language is not available but the second language is, the audio of the second language will be output.
Apart from this setting, you can select an audio track with the
button. See §5.2.4 for a detailed description.
32
Preference Settings
4.2
Video and audio settings
You have to configure the video
and audio settings appropriately
for your television set and other
devices. Select the Settings >
A/V Output menu. You should
see a screen like the left figure.
4.2.1
High definition television
The digital receiver supports various video resolutions from
576 to 1080. In general, a resolution of 720 or more is considered high definition. The higher the resolution is, the better
the quality is. However, if your television set does not support high definition, you cannot enjoy high definition quality
picture.
If you have the digital receiver linked to your television via the
Component video output (Y/Pb/Pr) or the HDMI output, you
have to set the HD Output option to Component. Otherwise,
you have to set it to SCART. The available values for the Video
Format option vary depending on how you set this option.
Set the Video Format option as you desire. If you set this option to 576P, the digital receiver will present even high definition programmes in resolution of 576. On the contrary, if you
set it to 1080I, the digital receiver will present even standard
definition programmes in resolution of 1080.
It is recommended to set it to Auto if you have a high definition
television. With that setting the digital receiver will present a
programme as it is without any resolution conversion. While
watching television you can change the resolution with the
4.2 Video and audio settings
33
V.Format button. Whenever you press it, the video resolution
is changed in turn.
NOTE
You can enjoy only standard definition video with the following video outputs:
• Composite video output (VIDEO)
• SCART output (TV)
4.2.2
Television aspect ratio
If you have a wide-screen television, set the TV Aspect Ratio
option to 16:9.
You can enjoy both wide-screen programmes and normalscreen programmes with your wide-screen television as the
above figures show. To watch normal-screen programmes
in full screen like the left figure, set the Display Format option
to Full. Normal-screen pictures then will be inflated to fit to
the width of the wide screen. Otherwise, to watch them in the
original ratio like the right figure, set it to Center. If you have
a normal-screen television, set the TV Aspect Ratio option to
4:3.
34
Preference Settings
You cannot fully enjoy wide-screen programmes with your
normal-screen television as the above figures show. The left
figure shows a normal picture displayed in the normal screen.
To watch wide-screen programmes in the shape like the centre figure, set the Display Format option to Letter Box. Widescreen pictures then will be reduced to fit to the width of the
normal screen. Otherwise, to watch them in the shape like the
right figure, set it to Center extract. Then wide-screen pictures
will be cut out on the left and right sides equally to fit to the
width of the normal screen.
4.2.3
Colour format
Through the TV SCART output, the digital receiver is able to
output video in various colour formats. If you have the digital
receiver linked to your television via this output, you should
set the SCART Output option to your desired colour format.
If you have connected via the RCA socket labeled VIDEO on
the back panel, you do not have to set this option because the
digital receiver outputs CVBS video through that RCA output
independently of the SCART output.
In general, it is known that the RGB colour format provides the
best video quality but the CVBS colour format does the least.
So RGB would be the most desirable option for this.
4.2.4
Another video device
You can have the digital receiver linked to another video device like a video recorder or a DVD player via the VCR SCART
output. In this case, the digital receiver will operate differently depending on the setting of the VCR SCART Type option. If the option is set to Standard, the digital receiver will
pass along the video from the video device to your television
when it starts playback. But if the option is set to External A/V,
the digital receiver will not pass the video automatically. You
have to press the AUX button to pass it along. It is impossible for the digital receiver to record the video from the video
4.3 Local time setting
35
device since the digital receiver is just a bypass for the video
recorder.
4.2.5
Audio mode
Basically, there are two audio sources as you can find two audio
sockets on the back panel of the digital receiver. You can enjoy
only one source or both of them in either stereo or mono. Set
the Sound Mode option as you desire.
Apart from this setting, you can change the sound mode with
the
button. See §5.2.4 for a detailed description.
The digital receiver can output two types of digital audio signals via the S/PDIF output. One is an encoded signal, and
the other is a decoded signal. If you have the digital receiver
linked to your audio-video receiver via the S/PDIF output, you
have to set the Dolby Digital option to Off, which means that the
digital receiver will output encoded Dolby Digital audio without decoding so that your audio-video receiver can decode it.
Otherwise, set it to On, then the digital receiver will output
decoded Dolby Digital audio, scaling it down to two channels.
NOTE
Only if the service you are currently watching provides
a Dolby Digital audio track, you can enjoy Dolby Digital
sound.
4.3
Local time setting
You should set your local time for timer events. If you do
not set the local time correctly, the programme time table provided by the programme guide may be distrustful. For the programme guide, refer to §5.3.
36
Preference Settings
Select the Settings > Time
menu. You should see a screen
like the left figure. You can set
the clock manually or use the
time signal, Greenwich Mean
Time (GMT), carried as part of
the digital television broadcast.
To use Greenwich Mean Time,
take the following steps:
1. Set the Mode option to Auto, then the Time Offset option
becomes enabled.
2. Set the Time Offset option to the time difference between
your time zone and GMT referring to Table 4.1.
3. To get Greenwich mean time, set the GMT Collection option to one among the followings:
Normal from all transponders
CAS Only from transponders of pay services
User Select from transponders specified by you
If you set it to User Select, then the Satellite option and
the Transponder option become enabled. Select your desired satellite and transponders at those options. With
the above settings, the digital receiver will scan all specified transponders one by one until it gets the Greenwich
Mean Time.
4. Make sure that your local time is correctly displayed on
the Local Time item.
To set the local time manually, set the Mode option to Manual and enter your local time to the Local Time option with
the numeric buttons. The time format is day/month/year 24hour:minute. To change the time format to 12-hour format, set
the Time Format option to 12 Hours.
4.3 Local time setting
37
If daylight saving time is observed in your state at the moment,
set the Daylight Saving Time option to On.
NOTE
Daylight saving time adds one hour to the time when the option is set to On. When setting the time offset from Greenwich Mean Time, make sure that time offset does not include
daylight saving time.
Table 4.1: Time offset table
Time offset
City
GMT − 12:00
GMT − 11:00
GMT − 10:00
GMT − 09:00
GMT − 08:00
GMT − 07:00
GMT − 06:00
GMT − 05:00
GMT − 04:00
GMT − 03:30
GMT − 03:00
GMT − 02:00
GMT − 01:00
GMT
GMT + 1:00
GMT + 2:00
GMT + 3:00
GMT + 3:30
GMT + 4:00
GMT + 4:30
GMT + 5:00
GMT + 5:30
GMT + 6:00
GMT + 7:00
GMT + 8:00
GMT + 9:00
GMT + 9:30
GMT + 10:00
GMT + 11:00
GMT + 12:00
Eniwetok, Kwajalein
Midway Island, Samoa
Hawaii
Alaska
Pacific Time US, Canada
Mountain Time US, Canada
Central Time US, Canada, Mexico City
Eastern Time US, Canada, Bogota, Lima
Atlantic Time Canada, La Paz
Newfoundland
Brazil, Georgetown, Buenos Aries
Mid-Atlantic
Azores, Cape Verde Islands
London, Lisbon, Casablanca
Paris, Brussels, Copenhagen, Madrid
South Africa, Kaliningrad
Baghdad, Riyadh, Moscow, St. Petersburg
Tehran
Abu Dhabi, Muscat, Baku, Tbilisi
Kabul
Ekaterinburg, Islamabad, Karachi, Tashkent
Bombay, Calcutta, Madras, New Delhi
Almaty, Dhaka, Colombo
Bangkok, Hanoi, Jakarta
Beijing, Perth, Singapore, Hong Kong
Tokyo, Seoul, Osaka, Sapporo, Yakutsk
Adelaide, Darwin
Eastern Australia, Guam, Vladivostok
Magadan, Solomon Islands, New Caledonia
Fiji, Auckland, Wellington, Kamchatka
38
4.4
Preference Settings
Parental control
In general, television programmes are classified according to
the level of violence, nudity and language of their content.
When you are watching a programme, you can check its programme classification on the information box. For the information box, see §5.2.3. You can prevent your children from
watching specific programmes by specifying a maximum permissible level.
Select the Settings > Parental
Control menu. You should see
a screen like the left figure,
and you will be asked your
Personal Identification Number
(PIN). The number is initially set
to ‘0000’ as default.
If you wish to block programmes for viewers aged 15 or above,
set the Censorship option to 15 (age). Setting it to No block
blocks no programme; on the other hand, setting it to Total
block blocks every programme.
NOTE
If a programme has no rating information, your censorship
setting will not take effect.
If anyone is trying to watch a programme that is of or above the
censorship setting, the person has to enter the personal identification number to override. To change the number, select the
Change PIN Code menu, then a box pops up, asking a new
PIN. Enter a desired number twice for confirmation.
You can also restrict uses of some menus. Selecting the Access
Control menu displays a list of menus that you can lock. If the
4.5 Options for recording
39
Time item is set to Locked, you have to enter the PIN when
accessing the Time menu. If you enter a wrong number, you
cannot use the menu. To release a locked item, set it to Unlocked.
4.5
Options for recording
To set the options for recording,
select the Settings > Recording
menu. You should see a screen
like the left figure.
To enable the time-shift function, you should set the Time Shifting option to anything other than Disable. The available range
for this option is 30 minutes to 5 hours. You will have the latest
of the current programme as long as the duration specified at
this option.
You can set the duration of the timer recording. Set the Timer
Recording Duration option as you desire. Its available range is
10 minutes to 3 hours.
Time padding is the feature of adding extra recording time to
the beginning or end of a programme, so that you do not miss
any part of the programme. Set the Time Padding of Timer
Recording option as you desire.
You can adjust the duration of the instant recording. Set the
Instant Recording Duration option as you desire. Its available
range is 30 minutes to 5 hours.
40
4.6
Preference Settings
Options for playback
To set the options for playback, select
the Settings > Playback menu. You
should see a screen like the left figure.
If you want to play back a recorded file from beginning, set
Starting Position option to Beginning. To play back a recorded
file from the part where you were watching, set this option to
Continuing.
To make a descrambled copy from a scrambled recording, set
the Descramble Mode option to Auto Recording; otherwise, set
this option to Normal.
You can adjust the jump interval that is for playback. Set the
Jump Time Interval option as you desire. Its available range is
10 seconds to 3 minutes.
If you want to enjoy more levels of playback speed, set the Trick
Mode Level option to 2x, 4x, 8x, 16x, 32x, 64x; otherwise, set
it to 4x, 16x, 64x.
NOTE
You can enjoy video files such as DivX with the digital receiver. However, the above options might not be effective
depending on the video files to be played. For detailed description on how to play back a video file, refer to §7.4.
If you have subtitle files such as .smi, .sub, .idx, and .srt, the
digital receiver can also display them. The Media Subtitle item
provides some options for video subtitle. When you play back
a video file with a subtitle file, if the subtitle does not match the
4.7 Options for on-screen display 41
video, then you can synchronise them by adjusting the value
of the Sync option. In addition, you can change the colour and
size of subtitle by setting the Font Color and Font Size options
to one you prefer.
4.7
Options for on-screen display
To set the options for the onscreen display (OSD), select the
Settings > OSD menu. You
should see a screen like the left
figure.
To adjust the transparency level of the OSD, set the OSD Transparency option as you desire. Its available range is 0 to 50 percent.
To adjust the display time of the information box, set the Info
Box Display Time option as you desire. Its available range is
1 to 30 seconds. If you set this option to No Info Box, the information box will not be displayed when you switch services.
However, pressing the
button will display the information
box. If you set this option to Never Hide, the information box
will always be displayed. For the information box, see §5.2.3.
In addition, you can raise or lower the position of the information box. Set the Info Box Position option as you desire. Its
available range is −10 to +3 lines. The higher you set the option, the lower the information box will be positioned.
If any service’s name is too long to fit the width of the service
name column on the services list screen, you can get it to scroll
by setting the Text Scroll option to anything other than Disable.
42
Preference Settings
With the choice of Full Scroll, it will be fully scrolled until its
end disappears; with the choice of Part Scroll, it will be scrolled
only to its end.
4.8
Options for standby mode
You can have the current time displayed on the front display
in standby mode. Select the Settings > Miscellaneous menu
and set the Standby Mode option to Active; otherwise, set it
to Passive. When you set the Standby Mode option to Active,
the receiver can also bypass the signal from the antenna. To
save power consumption, you might as well set the Automatic
Power Down option to Enable. With this option enabled, the
receiver will be turned off automatically when there is no manipulation over three hours.
43
Chapter 5
Every Day Use
5.1
Volume control
Use the V− and V+ buttons to alter the volume to a comfortable level. You may need to adjust the volume on your television set too. To temporarily switch off the sound, press the
button. Press it again to restore the sound to previous level.
5.2
Watching television
To change services, press the P− or P+ button. Pressing the
button switches to the previously viewed service. In addition, you can switch to your desired service by entering its
service number with the numeric buttons. You can also select
a service to watch in the services list.
5.2.1
The services list
To view the services list, press the OK button.
44
Every Day Use
On the services list, you can see
the service information as follows:
• Service number and name
• Transmitting satellite
• Multiplex information
A dollar sign ($) may be marked on some entries, indicating
pay service. To watch pay services, you need a subscription
card.
To select a desired service, put the highlight bar on its entry
with the P+ or P− button and press the OK button, then the
selected service will be presented.
Pressing the V− or V+ button skips over 10 entries up or
down. Entering a service number with the numeric buttons
puts the highlight bar on its entry.
You can switch between the television services list and the radio services list by pressing the
button.
To sort the services list by service name, press the
button.
Pressing this button once more makes it sorted by service number.
you can browse as a group the
services that have a same initial.
Press the
button at the services list screen, then you should
see a screen like the left figure.
5.2 Watching television
45
In the box on the left side, select a desired initial group by
putting the highlight bar on its entry, then all the services having the selected initial will be displayed in the box on the right
side. Move over to the right box with the
button, and then
select a service you want to view by putting the highlight bar
on its entry, then the selected service will be presented.
Pressing the
button displays additional options, with which
you can do the following:
• Select your desired satellite at the Satellite option, then
only services provided by the selected satellite will be
listed.
• By setting the Show Provider option to On, you can view
service entries by groups of broadcasters.
• To change the name of the highlighted service, select the
Rename option, then appears the on-screen keyboard
with which you can enter a new name. See §6.3 as to
how to use the on-screen keyboard.
• You can prevent other family members from watching
the highlighted service by setting the Lock option to
Locked. You have to enter your personal identification
number to watch or unlock it.
• To delete the highlighted service, select the Delete option, then you get asked for confirmation. With the
choice of Yes, the service will be deleted. If you want
to restore it as before, you have to perform service search
again. See §3.1 for service search.
• To add the highlighted service into a favourite group, select the Add to Fav option, then the favourite groups will
be displayed. Put the highlight bar on a desired group
and press the OK button.
• You can additionally sort the services list with the Sorting option as follows:
Default by service number
46
Every Day Use
Alphabetic by service name
Satellite by satellite
FTA–CAS from free services to pay services
CAS–FTA from pay services to free services
Provider by broadcaster
Fav–NoFav from favourite services to unfavourite services.
Transponder by transponder
5.2.2
The favourite service lists
You can select a service on a favourite list as well as on the
services list.
To display the favourite lists,
press the
button at the services list screen. For the services
list, see §5.2.1.
To select a favourite list, put
the highlight bar on a desired
favourite group list and press
the OK button, then the selected
favourite group’s services will be
listed.
As to how to edit the favourite lists, refer to §6.2.
To select a favourite service, put the hightlight bar on a desired
service and press the OK button, the it will be displayed. To
select another group, press the
button.
After you have selected a favourite service, if you then switch
to another service using the P+ or P− button, it will be also
another favourite service of the selected group. The digital receiver will remind you what group you have selected by displaying its name at the top right of the screen whenever you
switch services.
To return to the services list, press the
button. Besides that,
you can add or delete a favourite group or service.
5.2 Watching television
47
To add the service you are currently watching into a favourite
group, press the
button to display additional options, and
then select Add this service item.
To remove the currently highlighted favourite grop or service,
select Delete item in the additional option box, then you get
asked for confirmation; with the choice of Yes, it will be removed.
5.2.3
Viewing programme information
Pressing the
button displays the information box, on
which you can see all of the following:
•
•
•
•
•
•
•
•
•
Service number and name
Transmitting satellite
Transponder information
Signal level and quality
Programme name
Programme classification sign
Programme summary
Broadcasting time
Current time
In addition, you might see the following symbols:
• Subtitle symbol ( ) if subtitle tracks are provided on the
current programme.
• Teletext symbol (
current service.
) if teletext pages are provided on the
• Dolby Digital symbol (
) if a Dolby Digital audio
track is provided on the current programme.
• Lock symbol ( ) if the current service is locked.
• Dollar symbol ($) if the current service is a pay service.
• Multifeed symbol ( ) if the current programme is provided as a multifeed programme. To use this feature, refer to §5.4.
48
Every Day Use
If the electronic programme guide is provided on the current
service, you can see the information about the current and next
programmes with the V− or V+ button. You can also see the
information about other services with the P+ or P− . In this
case, you can change a service by pressing the OK button.
Pressing the
button once more displays detailed information about the current programme. To hide the information
box, press the EXIT button.
5.2.4
Selecting audio tracks
Some programmes are provided with audio tracks in one or
more languages. Pressing the
button displays available audio tracks. Once you select an audio track, that track will be
heard. In addition, you can enjoy audio tracks in four sound
modes: Stereo, Mono, Left or Right. However, if a multifeed
programme is provided at the moment, video tracks will be
displayed. In this case, you have to press the
button once
more to select an audio track.
5.2.5
Selecting subtitle tracks
Some programmes are provided with subtitle tracks in one or
more languages. If the current programme provides subtitle
tracks, the subtitle symbol ( ) will be marked on the information box. Pressing the
button displays available subtitle
tracks. Once you select a subtitle track, it will be displayed.
5.2.6
Viewing teletext
On some services, such information as weather reports, news
or stock quotations is provided by means of teletext. If the current service provides teletext, the teletext symbol ( ) will be
displayed on the information box. Press the
button to view
teletext pages.
Select a page to view by entering its page number with the numeric buttons. You can zoom into a teletext page with the
5.3 Viewing electronic programme guide
button, and adjust its transparency level with the
To clear the teletext screen, press the EXIT button.
5.3
49
button.
Viewing electronic programme guide
The Electronic Programme Guide (EPG) shows the current and
scheduled programmes that are or will be available on each
service with a short summary for each programme.
Pressing the GUIDE button displays the electronic programme
guide, on which you can see the
following:
•
•
•
•
Scheduled programmes
programme summary
Broadcasting date
Broadcasting time
To see detailed information of a desired programme, put the
highlight bar on the programme with the V− or V+ button
and press the
button. To switch to another service, press
the P− or P+ button.
You can travel over previous days with the
button.
travel over next days with the
button, and can
To see the programme guide for radio broadcasts, press the
button. To switch it back, press the
button again.
Pressing the
button will rearrange the form, swapping the
columns and rows. To switch it back, press the
button
again.
You can make a timer recording on the electronic programme
guide. See §7.1.3 for detailed description.
50
5.4
Every Day Use
Watching multifeed programme
Some broadcasts such as sports channels can provide a variety
of perspectives on a programme at the same time. We call it a
multifeed programme. You can select and watch a perspective
you prefer.
If a multifeed programme is provided on the current service,
the multifeed symbol ( ) will be marked on the information
box. Press the
button, then available video tracks will be
listed. Once you select one, it will be presented. At this time,
you have to press the
button once more to select audio
tracks.
5.5
Using time-shift
You can pause and resume a live television programme, and
even rewind and replay it. When you are watching a programme and you miss something, you can rewind and replay
it. Or when your attention is needed elsewhere, you can pause
a live TV and resume a short time later without losing any of
the programme.
When you do this, you are no
longer watching the live programme, instead you are watching a delayed presentation. This
is called time-shifted television.
You can skip commercials until
you catch up to the live broadcast.
In order to use the time-shift feature, set the Time Shifting option to desired duration of time. Then the digital receiver will
archive the programme as much time as you set in the option.
See §4.5.
5.5 Using time-shift
51
The time-shift will be reset each time you change to another
service. With the time-shift, the following operations are possible:
• To go back in time, hold down the
button; to go forward, hold down the
button. The progress bar is displayed momentarily with a preview window.
• You can navigate using the progress bar, refer to §7.3.1.
• You can jump backward and forward by pressing the
and
buttons. You can change the jump time at the
Jump Time Interval option. See §4.6.
• You can change playback speed. See §7.3.2 for slow motion. For fast motion, see §7.3.3.
• To check your current position in time-shift, press the
button. The time difference compared to live programme is displayed momentarily in top right corner of
the screen. A value of −02:00 means two minutes behind the live programme.
• To end time-shift, press the
gramme will be displayed.
button. The live pro-
NOTE
You can adjust some options for time-shift. Refer to §4.5.
52
Organising Services
Chapter 6
Organising Services
6.1
Editing the services list
You would have got the services list after service search. You
can rename, move, lock or delete service entries on the services
list.
Select the Edit Services > Edit
Service List menu. You should
see a screen like the left figure.
There are editing options on the
left column and service entries
on the right column.
Once you put the highlight bar on a desired option on the left
column and press the OK button, you can select a desired service to edit on the right column. To go over to the other column,
press the
button.
To edit the radio services list, press the
button, then radio
6.1 Editing the services list
53
service entries will be listed on the right column. To switch
back to the television services list, press it again.
To change the name of a service, select the Rename and select
a desired service; then the on-screen keyboard appears. See
§6.3 as to how to use the on-screen keyboard.
Unlike analogue broadcasts, each service does not have a
proper service number in digital broadcasts. Service numbers are just assigned to services in the order that they were
found in service search. So you can reassign a service number by moving a service entry. To move a service entry, select
the Move option and select a desired service; then the selected
service becomes darker. As you move it up or down, it gets
renumbered according to the position. Press the OK button to
fix it.
You can lock some services to prevent your children from
watching them. To lock a service, select the Lock option and
select a desired service; then the selected service gets marked
with a lock symbol ( ) on it. If anyone tries to watch a locked
service, the person has to enter the personal identification
number that is set to the Change PIN Code option. See §4.4
for this option. Pressing the OK button on a locked service
entry turns it back to be unlocked.
To delete a service, select the Delete option and select a desired
service with the OK button, and then press the EXIT button;
you get asked for confirmation. If you select Yes, the selected
service will be deleted. If you want to undo the deleted service,
there is nothing you can do but perform a service search again.
Once you select the Sort option on the left column, sorting options are displayed as follows:
Default by service number
Alphabetic by service name
Satellite by satellite
FTA–CAS from free services to pay services
CAS–FTA from pay services to free services
54
Organising Services
Fav–NoFav from favourite services to unfavourite services
Provider by broadcaster
Transponder by transponder
6.2
Editing the favourite lists
You can make your own favourite service lists. In fact, you can
define multiple favourite service lists, each being a ‘group’ of
chosen services.
Select the Edit Services > Edit
Favorite List menu. You should
see a screen like the left figure.
There are three columns:
• Group list (left)
• Favourites list (centre)
• Services list (right)
The services list contains all available services, whereas the
favourites list contains only chosen services that have been
added to the highlighted group. As you move the highlight
bar up or down on the group list, favourite services belonging
to the highlighted group get shown in the favourites list.
You can add up to 30 groups. To add a new group, select the
NEW item in the group list, then the on-screen keyboard appears. See §6.3 as to how to use the on-screen keyboard.
To rename a group, put the highlight bar on the group entry
you want and press the button, then the on-screen keyboard
likewise appears.
To delete a group, put the highlight bar on the group entry you
want and press the
button, then a message box appears,
asking you for confirmation. With the choice of Yes, it will be
deleted.
6.2 Editing the favourite lists
55
You can add a favourite service to a group by taking the following steps:
1. Put the highlight bar on a desired group entry in the
group list and press the OK button to select it. The highlight bar then moves to the services list.
2. To add a service to the selected group, put the highlight
bar on a desired service entry and press the OK button.
The selected service entry gets added to the favourite list.
Repeat this step to add more entries.
3. Press the
button, and the highlight bar gets moved to
the favourite list. You can delete a favourite entry with
the OK button.
4. To select another group, press the
button again, then
the highlight bar gets moved to each column.
Furthermore, you can rearrange a group’s favourites by moving a favourite entry. To move a favourite entry, put the highlight bar on the favourite entry you want and press the
but
ton. Move it to a desired place and press the OK button.
To add radio services, press the
button, then radio service
entries get listed in the services list. To recall the television
button
services list after adding radio services, press the
again.
As to how to use the favourite service lists you organised, refer
to §5.2.2.
56
6.3
Organising Services
How to use on-screen keyboard
You can move the highlight key
horizontally with the V− and
V+ buttons and vertically with
the P+ and P− buttons. Press
ing the OK button on a key enters its letter in the input line.
To type a space, select the Space key or alternatively press the
button. To type lower case letters or numerals, select the
Shift key or alternatively press the
button. To delete a letter, put the cursor to the right of the desired letter on the input
line and then select the Del key or alternatively press
button. You must select the Save key or alternatively press the
button to complete your typing; otherwise if you press the
EXIT
button, it will not be saved.
57
Chapter 7
Recording and Playback
If you want to record TV programmes, you have to
link an external hard drive to the USB port of the
digital receiver.
NOTE
The external hard drive should be formatted in
the NTFS file system.
7.1
Recording a programme
Once a recording gets started, a symbol like the left figure will be displayed at the top right of the screen for a
few seconds.
CAUTION
Do not move the digital receiver nor pull out the power
plug while it is running. It may cause damage to recorded
programmes. Topfield is not responsible for damages inflicted on files that are stored on the hard drive.
58
Recording and Playback
7.1.1
Instant recording
To instantly record a programme you are watching at present,
press the
button.
Pressing the
button will not pause the current recording
like it does with a video recorder. Instead, pressing the
button will pause the live show and begin time-shifting within the
current recording even with the Time Shifting option disabled.
In short, it is still possible to pause a recording, but literally
recording continues in the digital receiver.
After a recording has started,
button displays
pressing the
a menu like the left figure, in
which you can set the recording
duration.
To specify an arbitrary recording duration, set the Duration op
tion as you desire with the V− and V+ buttons and press the
OK button; the recording will end at the specified time.
If the information about the next programme is provided by
the electronic programme guide, the After this program and
After next program options will be enabled. Once the After this
program option is selected, the current recording will stop at
the time when the current programme is scheduled to end.
Likewise, once the After next program option is selected, the
current recording will stop at the time when the next programme is scheduled to end.
7.1 Recording a programme
59
To stop recording, press the
button; then a box like the
left figure appears, which shows
the programme currently being
recorded. Select recording by
using navigation buttons then
press OK button to stop the
recording.
While a recording is going on, you can play back one of the
recorded programmes.
To view the recorded programme
list, press the
button or alternatively select the Recorded
Program menu. See §7.2 for detailed description about the
recorded programme list.
7.1.2
Timer recording
You can set a programme to be recorded at a specific time.
Even if the digital receiver is in standby mode, it will switch
into active mode and start recording at a specified time. When
the recording comes to the end, the digital receiver will switch
back into standby mode again in one minute. However, if you
press any button on the remote control or on the front panel
even just one time, the digital receiver will not switch into
standby mode.
60
Recording and Playback
To add a timer recording, select
the Reservation menu, then the
timer list will be displayed. To
add a new timer event, press the
button, and a box like the left
figure appears. Take the following steps:
1. Set the Record option to On to make a recording. If this
option is set to Off, the digital receiver will turn on at the
specified time but not record; instead, you may record
with your video recorder or suchlike in this case.
2. You may have two sources for recording, TV and radio.
Set the Type option to your desired source.
3. Set the Satellite option to the satellite which transmits the
service you want. Pressing the OK button on this option
displays a satellite list, from which you can select your
desired satellite. Set the Tuner Select option to a tuner
to receive your desired service.
4. Set the Service option to the service which provides the
programme you want. Pressing the OK button on this
option displays a services list, from which you can select
your desired service.
5. Set the Mode option as you desire. There are five timer
modes:
One Time means literally ‘one time’.
Every Day means literally ‘every day’.
Every Weekend means ‘Saturday and Sunday every week’.
Weekly means ‘one day every week’.
Every Weekday means ‘from Monday to Friday every
week’.
7.1 Recording a programme
61
If your favourite programme is broadcast at weekends
and you wish to record every episode of the programme,
set the Mode option to Every Weekend.
6. Set the Date option to a desired date, on which the digital
receiver will turn on. The date format is day/month/yearday of the week.
Set the Start Time option to a desired time, at which the
recording will be started. The time format is hour:minute.
7. Set the Duration option to a desired time, in which the
recording will be finished.
8. Pressing the OK button on the File Name option displays
the on-screen keyboard, with which you can specify a
file name for the timer recording. If you do not specify
anything, it will be named after the service name. See
§6.3 as to how to use the on-screen keyboard.
9. To set a recording reservation with the above settings,
select the OK item; otherwise, it will not be saved and
will not occur.
You can also edit or delete timer events in the timer list. To edit
a timer entry, put the highlight bar on the entry you want and
press OK button; then appears a box in which you can change
its settings in the same manner as making a new one.
To delete a timer event, put the highlight bar on the entry you
want to remove and press the
button, then you get asked
for confirmation. With the choice of Yes, it will be deleted. To
delete all timer event, press the
button.
You can sort timer events by time with the
button.
62
Recording and Playback
7.1.3
Scheduling recordings using the programme guide
If the electronic programme
guide is properly provided,
you can make timer events on
it. The instructions on how to
make timer recordings using the
electronic programme guide are
as follows:
1. Press the GUIDE button to display the electronic programme guide.
2. Select a programme you want to record with the navigation buttons.
3. To make a timer event without recording, press the OK button; the letter P is displayed. To make a timer event
with recording, press it once more or alternatively press
the
button, then the letter R is displayed.
4. Pressing the OK button once more will cancel the timer.
7.1.4
Recording a pay service programme
You can record a pay service programme without the subscription card. However, you need the subscription card to play
it back because it has not been descrambled. So it is recommended to record pay service programmes with a proper subscription card so that they can be descrambled and recorded.
In that case, you can enjoy them without the subscription card
like free services.
To record a programme of a pay service in descrambled form,
take the following steps:
1. Select a programme of a pay service you want to record.
7.2 File archive 63
2. Make sure that the subscription card is inserted in the
slot on the front of the digital receiver.
3. Start recording.
4. Do not switch to other service nor use time-shift until
recording is finished.
NOTE
If you switch to other service or use time-shift in the middle
of recording a pay programme, it will be recorded without
descrambling from that moment. Even if the recording is
only partially descrambled, you need the subscription card
to play it back.
7.2
File archive
When a programme is recorded, it is stored as a file on the hard
drive of the digital receiver. You can select a recording to play
back from the recorded programme list.
Select the Recorded Program
menu or alternatively press
the
button to display the
recorded programme list. The
file information is comprised
of the following elements: file
number, file name, recording
time, running time, file size and
so on.
You can play, move, delete, rename and lock a recording file.
You can also sort the recording files by file name, running time
or file size. In addition, you can make a new folder.
64
Recording and Playback
7.2.1
To delete a recording
To delete a recording, put the highlight bar on it and press
the
button, then you get asked for confirmation. With the
choice of Yes, it will be deleted.
7.2.2
To sort recordings
To sort the recordings, take the following steps:
1. Press the
button to display additional options.
2. Set the Sorting option to Alphabetic, Time or Size as you
want.
3. Press the EXIT button.
4. They will be sorted by the specified option.
7.2.3
To lock a recording
To lock a recording so that other persons cannot play or delete
it, take the following steps:
1. Put the highlight bar on a desired recording.
2. Press the
button to display additional options.
3. Set the Lock option to Locked.
4. Press the EXIT button.
5. The lock symbol ( ) is displayed on it.
If you select a locked recording to play it back, you will be
asked for your personal identification number.
7.2.4
To rename a recording
To change a recording’s name, take the following steps:
1. Put the highlight bar on a desired recording.
2. Press the
button to display additional options.
3. Select the Rename option, and the on-screen keyboard
appears. Change the name and save it. See §6.3 as to
how to use the on-screen keyboard.
7.3 Playing back a recording
7.2.5
65
To make a new folder
To make a new folder, press the
button, then a new folder
named GROUP # is created. You can change its name in the
same manner as renaming a recording. See above.
7.2.6
To move a recording to another folder
To move a recording to another folder, put the highlight bar
on a desired recording and press the
button. If an external
hard drive is connected to the digital receiver, you get asked
to select between the built-in and external hard drive. Select
Internal, then the folders are listed. Once you choose a folder,
the recording is moved to it.
7.3
Playing back a recording
When a programme is recorded, its additional contents such
as audio track or subtitle track are also recorded together. So
you can enjoy them while playing back a recording.
The instructions on how to play a recording are as follows:
1. Select the Recorded Program menu or alternatively press
button to display the list of recorded programmes.
the
2. Put the highlight bar on a desired recording and press
the OK button, then an option box pops up.
3. To play from beginning, set the Starting Position option to Beginning; to play from the point that you have
stopped at the last time, set it to Continuing. To start playback, select the Play item.
4. To stop playback, press the
button.
During playback, you can enjoy the following tricks:
• To see the detailed information about the currently
played recording, press the
button; then the information box appears and shows its file name, running
time, programme information, and so on.
66
Recording and Playback
• To pause playback, press the
press the
button.
button. To resume it,
• To view the progress bar, press the
press the
button again.
button; to hide it,
• When the progress bar is hidden, you can move to a desired scene by entering a progress percentage with the
numeric buttons.
7.3.1
To navigate using the progress bar
First press the
button to display the progress bar.
• To go forward, hold down the V+ button; to go back
ward, hold down the V− button.
• If there are no bookmarks, you can jump forward by the
minute set to the Jump time Interval option with the
button. See §4.6 for that option. Refer to §7.3.4 as to how
to bookmark a position.
• To jump to the beginning, press the
• To jump to the end, press the
button.
• To hide the progress bar, press the
7.3.2
button.
button again.
To play in slow motion
To watch in slow motion during a playback, press the
button. If you press it repeatedly, the playback speed changes in 4
steps: 1/2, 1/4, 1/8 and 1/16 times. To resume normal speed,
press the
button.
7.3.3
To play in fast motion
To watch in fast motion during a playback, press the
button. If you press it repeatedly, the playback speed changes. To
resume normal speed, press the
button.
You can play not only forward but also backward in fast motion. To play backward, press the
button. If you press it
7.3 Playing back a recording
67
repeatedly, the playback speed changes. To resume normal
speed, press the
button.
You can change the playback speed in 3 steps (4, 16 and 64
times) or in 6 steps (2, 4, 8, 16, 32 and 64 times). See §4.6.
7.3.4
To make a bookmark
You can mark favourite parts of
a recording by creating bookmarks and then jump to them in
sequence. Bookmarks are stored
with the recording so that you
can use them again afterwards.
To make bookmarks, take the following steps during playback:
1. Press the
button to display the progress bar.
2. To add a bookmark, press the
button at a desired
scene, then you will see a small pointer appear above the
progress bar like in the picture above.
3. To jump forward to the next bookmark, press the
ton.
7.3.5
but-
To play back a recording repeatedly
You can play back a recording repeatedly both in whole and in
part.
To play back in whole, press the
button when the progress
bar is hidden, then the repetition symbol (
) is displayed on
the information box. To cancel it, press the
button again.
To play back in part, take the following steps:
1. Press the
button to display the progress bar.
68
Recording and Playback
2. Move to the beginning scene of the part you want to play
repeatedly by holding down the V− or V+ button.
3. Press the
button, then the pointer starts to blink.
4. Move to the end scene; the selected part is marked in
black.
5. Press the
button again to start repeated playback.
6. To cancel it, press the
is displayed.
7.3.6
button when the progress bar
To play back recordings in sequence
You can play several recordings continuously in sequence by
performing the following steps:
1. Press the
button or alternatively select the Recorded
Program menu to display the list of recorded programmes.
2. Select each desired recording with the
button. Once
a recording is selected, it gets numbered.
3. Press the
button to start playback.
4. The selected recordings are played in the sequence that
they are numbered.
5. To jump to the beginning of the next recording in the
queue, press the
button to display the progress bar,
then press the
button.
7.3.7
To play back a scrambled recording
If you have recorded a programme of a pay service with the
subscription card, you can play it as freely like that of a free
service. Otherwise you need the subscription card to play it
back because it has been recorded without descrambling even
though it may have been partially descrambled.
On the recorded programme list, a purely green $ indicates the
recording has been wholly descrambled; on the other hand, a
7.4 Playing back a video file
69
yellowish green $ indicates it has been partially descrambled,
and a purely yellow $ indicates it has not been descrambled at
all.
There are two ways to fully descramble a scrambled recording
so that you can play it back without the subscription card later
on. One is to make a copy while playing it back to the end; the
other is to make the copy job to be carried out as a timer event.
The first method is very easy to carry out. When you select
an entry to play in the recorded programme list, the playback
option box appears. Simply set the Descramble Mode option
to Auto Recording. Then a descrambled copy will be created
while you are watching it.
NOTE
You should get the scrambled recordings descrambled as
soon as possible. You could lose the chance to descramble forever if you hang around too long because broadcasting operators frequently changes the key signal for descrambling.
7.4
Playing back a video file
If you have media files such as photos, videos, and music, you
can also enjoy them with the digital receiver by simply selecting a file you want to display or play back. Media file formats
that you can play back with the digital receiver are as follows:
• video: DivX, XviD, vob, mkv, mp4, and avi;
• photo: jpg;
• music: MP3.
When playing a video file, if it has its own one or more subtitle files, you can select one you prefer with the
button to
display subtitle.
70
Recording and Playback
NOTE
This digital receiver supports only version 3.x, 4.x, 5.x, and
6.x of the Divx format.
7.5
Formatting the hard disk
If a new hard drive is installed, it must be formatted because
you can neither record nor use time-shift with an unformatted
hard disk.
You can delete permanently all contents stored in a hard drive
by formatting it. Select the Installation > System Recovery >
Format Hard Disk menu, and then select the hard drive you
want to format. To format the built-in hard drive, select the
option to Internal; otherwise to format the external hard drive
which is connected to the digital receiver, select the option to
External. With pressing the OK button, you get asked for confirmation. Formatting will start with the choice of Yes.
NOTE
The hard drive on the digital receiver will be formatted in
the NTFS file system.
71
Chapter 8
Firmware Update
The digital receiver has a stable and convenient firmware to
use. However, once in a while a new firmware may be released to improve the digital receiver. You can get the latest firmware and the firmware update tool, which runs on
most versions of Windows, from the Topfield website, http:
//www.i-topfield.com.
8.1
From a memory stick
If you have a USB memory stick, you can update the firmware
from it by taking the following steps:
1. Download a new firmware from the Topfield website.
2. Copy the firmware file to your memory
stick.
3. Insert the USB memory stick into the USB
port on the digital receiver.
4. Select the Installation > Firmware Upgrade > USB
Firmware Upgrade menu, and the files in the USB memory will be listed.
72
Firmware Update
5. Place the highlight bar on the right firmware file and
press the OK button, and a countdown will be displayed
on the front display of the digital receiver.
6. When the message of ‘END’ appears, restart the digital
receiver.
8.2
Over the air
You can get a new firmware over
the air.
Select the Installation > Firmware Upgrade > OTA
Firmware Upgrade menu. You
should see a screen like the left
figure.
Satellite
Frequency
Symbol Rate
Polarisation
PID
Astra (19.2° E)
12603 MHz
22000 KS/s
Horizontal
347
On the left table is presented
the transponder information
appointed by the manufacturer, Topfield, for firmware
update.
This transponder information can be changed. You can get the
information from the website, http://www.i-topfield.com.
Selecting the Start command starts firmware update.
Manufactured under license from Dolby Laboratories. “Dolby” and
the double-D symbol are trademarks of Dolby Laboratories.
R
is a digital video format created by DivX,Inc. This is an
DivX⃝
official DivX Certified device that plays DivX video. Visit http:
//www.divx.com for more information and software tools to convert
your files into DivX video.
R
About DivX Video-On-Demand: This DivX Certified⃝
device must
be registered in order to play DivX Video-on-Demand (VOD) content. To generate the registration code, locate the DivX VOD section
in the device setup menu. Go to http://vod.divx.com with this
code to complete the registration process and learn more about DivX
VOD.
Correct disposal of this product
This marking shown on the product or its literature indicates that
it should not be disposed with other household wastes at the end
of its working life. To prevent possible harm to the environment
or human health from uncontrolled waste disposal, please separate
this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources. Household users should
contact either the retailer where they purchased this product or their
local government office for details of where and how they can dispose this product for environmentally safe recycling. Business users
should contact their supplier and check the terms and conditions of
the purchase contract. This product should not be mixed with other
commercial wastes for disposal.
At any time during the life of a product Topfield Co., Ltd. may change or modify the hardware or software on any product to introduce new features or improve the functionality of
the product.
Copyright © 2010, Topfield Co., Ltd. All rights reserved.
http://www.i-topfield.com
English version
110S-F7A89-701-1
">