Nokia 6670 mobile phone User guide

DECLARATION OF CONFORMITY

We, NOKIA CORPORATION declare under our sole responsibility that the product

RH-67 is in conformity with the provisions of the following Council Directive:

1999/5/EC. A copy of the Declaration of Conformity can be found at http://www.nokia.com/phones/declaration_of_conformity/

Copyright © 2004 Nokia. All rights reserved.

Reproduction, transfer, distribution or storage of part or all of the contents in this document in any form without the prior written permission of Nokia is prohibited.

Nokia, Nokia Connecting People and Xpress-on are trademarks or registered trademarks of Nokia Corporation. Other product and company names mentioned herein may be trademarks or tradenames of their respective owners.

Nokia tune is a sound mark of Nokia Corporation.

This product includes software licensed from Symbian Software Ltd © 1998-2004. Symbian and Symbian OS are trademarks of Symbian Ltd.

Java™ and all Java-based marks are trademarks or registered trademarks of Sun Microsystems, Inc.

Stac ®, LZS ®, ©1996, Stac, Inc., ©1994-1996 Microsoft Corporation. Includes one or more U.S. Patents: No. 4701745, 5016009, 5126739, 5146221, and 5414425. Other patents pending.

Hi/fn ®, LZS ®,©1988-98, Hi/fn. Includes one or more U.S. Patents: No. 4701745, 5016009, 5126739, 5146221, and 5414425. Other patents pending.

Part of the software in this product is © Copyright ANT Ltd. 1998. All rights reserved.

US Patent No 5818437 and other pending patents. T9 text input software Copyright (C) 1997-2004. Tegic Communications, Inc. All rights reserved.

Bluetooth is a registered trademark of Bluetooth SIG, Inc.

Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice.

Under no circumstances shall Nokia be responsible for any loss of data or income or any special, incidental, consequential or indirect damages howsoever caused.

The contents of this document are provided ‘as is’. Except as required by applicable law, no warranties of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy, reliability or contents of this document. Nokia reserves the right to revise this document or withdraw it at any time without prior notice

The availability of particular products may vary by region. Please check with the Nokia dealer nearest to you.

9234483

Issue 1 EN


Contents

For your safety ........................................ 7

General information ............................. 10

Essential indicators in standby mode .........................10

Menu ....................................................................................11

Switching between applications ..........................12

Actions common to all applications ...........................12

Volume control..................................................................13

Shared memory .................................................................14

Your phone ............................................ 15

Making a call .....................................................................15

Making a call using the Contacts directory ......15

Calling your voice mailbox (Network Service)..16

Speed dialling a phone number ............................16

Making a conference call (Network Service) ....16

Answering a call ...............................................................17

Options during a call ...............................................17

Call waiting (Network Service) .............................18

Diverting calls (Network Service).........................18

Log - Call register and general log..............................19

GPRS data counter ...................................................19

Recent calls register.................................................19

Call duration...............................................................20

Viewing the general log..........................................21

Personal information ............................ 22

Contacts..............................................................................22

Creating and editing contact cards.....................22

Copying contacts between the SIM card and phone memory........................................................................23

Adding a ringing tone for a contact card or group

23

Voice dialling .............................................................24

Assigning speed dialling keys................................25

Viewing subscribed contacts.................................25

Managing contact groups......................................26

Presence (Network Service)...........................................26

Changing your availability information .............27

Changing who can view your Presence information

27

Updating your Presence information..................29

Presence settings......................................................30

Positioning (Network Service) ......................................30

Calendar..............................................................................31

Creating calendar entries.......................................31

To-do....................................................................................32

Importing data from compatible Nokia phones ......33

Multimedia ............................................ 34


Camera................................................................................ 34

Taking pictures.......................................................... 34

Recording videos ...................................................... 36

Viewing images................................................................. 37

Zooming on a saved image.................................... 37

Keyboard shortcuts.................................................. 38

RealPlayer™........................................................................ 38

Playing media files................................................... 39

Changing the settings............................................. 40

Movie director................................................................... 40

Gallery ................................................................................. 41

Opening files.............................................................. 42

Other default folders............................................... 42

Downloading files .................................................... 43

Uploading images to an image server (Network

Service)........................................................................ 43

Messaging.............................................. 45

Writing text ....................................................................... 46

Using traditional text input .................................. 46

Using predictive text input.................................... 47

Copying text to the clipboard............................... 49

Writing and sending messages .................................... 50

Settings needed for multimedia messaging ..... 51

Settings needed for e-mail.................................... 51

Inbox - receiving messages........................................... 52

Viewing multimedia objects.................................. 52

Receiving smart messages..................................... 52


Receiving service messages (Network Service) 53

My folders ......................................................................... 54

Remote mailbox (Network Service) ............................ 54

Opening the mailbox ............................................... 54

Retrieving e-mail messages from the mailbox 54

Deleting e-mail messages...................................... 55

Disconnecting from mailbox ................................. 56

Outbox................................................................................. 56

Viewing messages on a SIM card ................................ 57

Cell broadcast (Network Service) ................................ 57

Service command editor ................................................ 58

Messaging settings.......................................................... 58

Settings for text messages .................................... 58

Settings for multimedia messages ...................... 59

Settings for e-mail................................................... 60

Settings for service messages............................... 62

Settings for Cell broadcast (Network Service). 62

Settings for the Other folder................................. 62

Tools........................................................64

Using the Setting Wizard............................................... 64

Settings............................................................................... 65

Changing general settings..................................... 65

Phone settings........................................................... 66

Call settings ............................................................... 67

Connection settings................................................. 68

Date and time............................................................ 72

Call barring (Network Service) ............................. 72

Network .......................................................................73

Enhancement settings.............................................73

Security................................................................................74

Phone and SIM ..........................................................74

Certif. management .................................................76

Device manager.................................................................77

File manager ......................................................................78

Viewing memory consumption .............................78

Voice commands...............................................................79

Adding a voice command to an application .....79

Starting an application using a voice command80

Replaying, erasing, or changing a voice command

81

Memory card......................................................................81

Format memory card................................................81

Backing up and restoring information................82

Locking the memory card .......................................82

Checking memory consumption ...........................83

Personalising your phone ..................... 84

Profiles.................................................................................84

Changing the profile ................................................84

Customising profiles ................................................84

Themes.................................................................................85

Editing themes...........................................................86

Extras ..................................................... 87

Wallet .................................................................................87

Entering the wallet code ........................................87

Storing personal card details ................................88

Creating personal notes..........................................89

Creating a wallet profile.........................................89

Retrieving information from the wallet to your browser........................................................................90

Viewing ticket details..............................................90

Wallet settings ..........................................................90

Resetting the wallet and wallet code.................91

Calculator ...........................................................................91

Converter ............................................................................91

Converting units .......................................................92

Setting a base currency and exchange rates....92

Notes....................................................................................93

Clock ....................................................................................93

Changing clock settings .........................................93

Setting an alarm .......................................................93

Recorder..............................................................................94

Chat (Network Service)...................................................94

Before using Chat.....................................................95

Connecting to a chat server ..................................95

Modifying your chat settings................................95

Joining and leaving a chat group ........................96

Searching for chat groups and users ..................97

Chatting in a chat group........................................97

Starting and viewing individual conversations 98

Chat contacts ............................................................99

Editing chat group settings ...................................99


Chat and Presence servers...................................100

Go to..................................................................................101

Adding shortcuts ....................................................101

Services and Applications .................. 102

Web (Mobile browser) ..................................................102

Basic steps for accessing .....................................102

Setting up the phone for the browser service103

Making a connection ............................................103

Viewing bookmarks................................................104

Browsing ...................................................................104

Downloading............................................................106

Ending a connection..............................................107

Browser settings .....................................................107

Application manager.....................................................109

Installing applications - general information 109

Removing an application .....................................111

Connectivity ........................................ 112

Bluetooth connection ...................................................112

Bluetooth settings..................................................113

Sending data via Bluetooth.................................113

Paired devices view................................................115

Receiving data via Bluetooth..............................115

Disconnecting Bluetooth......................................116

Connection manager.....................................................116

Viewing connection details .................................116

Ending connections ...............................................117

Connecting your phone to a compatible computer117

Sync - remote synchronisation ..................................117

Creating a new synchronisation profile...........118

Synchronising data ................................................119

Troubleshooting .................................. 120

Q&A....................................................................................121

Battery information ........................... 123

Care and Maintenance....................... 124

Additional safety information........... 125

Index .................................................... 128


For your safety

Read these simple guidelines. Breaking the rules may be dangerous or illegal. Further detailed information is given in this manual.

SWITCH ON SAFELY Do not switch the phone on when wireless phone use is prohibited or when it may cause interference or danger.

ROAD SAFETY COMES FIRST Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety.

INTERFERENCE All wireless phones may be subject to interference, which could affect performance.

SWITCH OFF IN HOSPITALS Follow any restrictions. Switch the phone off near medical equipment.

SWITCH OFF IN AIRCRAFT Follow any restrictions. Wireless devices can cause interference in aircraft.

SWITCH OFF WHEN REFUELLING Don’t use the phone at a refuelling point. Don’t use near fuel or chemicals.

SWITCH OFF NEAR BLASTING Follow any restrictions. Don't use the phone where blasting is in progress.

USE SENSIBLY Use only in the normal position as explained in the product documentation. Don’t touch the antenna unnecessarily.

QUALIFIED SERVICE Only qualified personnel may install or repair this product.

ENHANCEMENTS AND BATTERIES Use only approved enhancements and batteries. Do not connect incompatible products.

WATER-RESISTANCE Your phone is not water-resistant. Keep it dry.

BACKUP COPIES Remember to make backup copies or keep a written record of all important information stored in your phone.

CONNECTING TO OTHER DEVICES When connecting to any other device, read its user guide for detailed safety instructions. Do not connect incompatible products.


7

EMERGENCY CALLS Ensure the phone is switched on and in service. Press as many times as needed to clear the display and return to the start screen. Key in the emergency number, then press . Give your location.

Do not end the call until given premission to do so.

About your device

The wireless device described in this guide is approved for use on the EGSM 900 and GSM1800 and 1900 networks.

Contact your service provider for more information about networks.

When using the features in this device, obey all laws and respect privacy and legitimate rights of others.

Warning: To use any features in this device, other than the alarm clock, the device must be switched on. Do not switch the device on when wireless device use may cause interference or danger.

with your service provider before you can utilize Network

Services. Your service provider may need to give you additional instructions for their use and explain what charges will apply. Some networks may have limitations that affect how you can use Network Services. For instance, some networks may not support all languagedependent characters and services.

Your service provider may have requested that certain features be disabled or not activated in your device. If so, they will not appear on your device menu. Contact your service provider for more information.

This device supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP protocols. Some features of this device, such as MMS, browsing, e-mail, remote SyncML, and content downloading via browser or over MMS, require network support for these technologies.

Network Services

To use the phone you must have service from a wireless service provider. Many of the features in this device depend on features in the wireless network to function.

These Network Services may not be available on all networks or you may have to make specific arrangements

Chargers and enhancements

Note: Check the model number of any charger before use with this device. This device is intended for use when supplied with power from ACP-8,

ACP-12, LCH-9 and LCH-12.

WARNING! Use only batteries, chargers, and enhancements approved by Nokia for use with this particular model. The use of any other types may invalidate any approval or warranty, and may be dangerous.

8


For availability of approved enhancements, please check with your dealer. When you disconnect the power cord of any enhancement, grasp and pull the plug, not the cord.

Your device and its enhancements may contain small parts. Keep them out of reach of small children.


9

General information

Warning: To use any features in this device, other than the alarm clock, the device must be switched on. Do not switch the device on when wireless device use may cause interference or danger.

Your Nokia 6670 phone provides various functions that are ideal for daily use, such as

Camera, Video recorder, Messaging, E-mail, Wallet, Clock, Calculator, and Calendar.

Stickers in the sales package

• The stickers included on the warranty card, in the sales package, contain important information for service and customer support purposes. The sales package also includes instructions on how you should use these stickers.

Essential indicators in standby mode

- You have received one or several messages to the Inbox in Messaging.

- You have received one or several voice messages.

See “Calling your voice mailbox

(Network Service)” on page 16.

- There are messages waiting to be sent in Outbox.

-

Ringing type

has been set to

Silent

,

Message alert tone

to

Off

, and

Chat alert tone

to

On

in the currently active profile.

- The phone’s keypad is locked. See the Getting Started guide.

- You have an active alarm.

- You can make calls using phone line 2 only (Network Service). See “Line in use

(Network Service)” on page 68.

10


- All calls to the phone are diverted. - Indicates that all calls to the phone are

diverted to a voice mailbox. See “Diverting calls (Network Service)” on page 18.

If you have

two phone lines, the divert indicator for the first line is and for the second line .

- A data call is active.

- Shown instead of the antenna symbol (shown in the top left corner in standby mode) when there is an active GPRS connection. - Shown when the GPRS connection is put on hold during voice calls.

- Bluetooth is active. When data is transmitted via Bluetooth, is shown.

Menu

Press (Menu key) to display the main Menu. In the Menu, you can access all the applications in your phone.

Moving in the Menu

• Press the scroll key on the top , bottom , left and right (shown with blue arrows 1 to 4) to navigate the Menu.

Opening applications or folders

• Scroll to an application or a folder and press the centre of the scroll key (shown with blue arrow 5) to open it.

Closing applications

• Backstep by pressing

Back

or

Exit

as many times as needed to return to standby mode or select

Options

→

Exit

.

Options in the

Menu:

Open

,

List view

/

Grid view

,

Move

,

Move to folder

,

New folder

,

App. downloads

,

Memory details

,

Help

and

Exit

.

3

5

1

2

4

Fig. 1 Using the scroll key.


11

Fig. 2 Switching between applications.

Switching between applications

If you have several applications open and want to switch from one application to another, press and hold (Menu key). The application switching window opens showing a list of applications that are currently open. Scroll to an application and press to go to it.

Actions common to all applications

• Opening items for viewing - When you are viewing a list of files or folders, to open an item, scroll to an item and press , or select

Options

→

Open

.

• Editing items - To open an item for editing, you sometimes need to first open it for viewing and then select

Options

→

Edit

, if you want to change its contents. Use the scroll key to scroll through all fields of the item.

• Renaming items - To give a new name to a file or folder, scroll to it and select

Options

→

Rename

.

• Removing, deleting items - Scroll to the item and select

Options

→

Delete

or press .

To delete many items at a time, you first need to mark them. See the next paragraph:

‘Marking an item’.

• Marking an item - There are several ways to select items when you are in a list.

• To select one item at a time, scroll to it and select

Options

→

Mark/Unmark

→

Mark

or press and at the same time. A check mark is placed next to the item.

• To select all items in the list, select

Options

→

Mark/Unmark

→

Mark all

.

• Marking multiple items - Press and hold , then move the scroll key down or up.

As the selection moves, a check mark is placed next to the items. To end the selection, stop the scrolling with the scroll key and then release .

After you have selected all the items you want, you can move or delete them by selecting

Options

→

Move to folder

or

Delete

.

• To unmark an item, scroll to it and select

Options

→

Mark/Unmark

→

Unmark

or press

and at the same time.

• Creating folders - To create a new folder, select

Options

→

New folder

. You are asked to give a name to the folder (max. 35 letters).

12


• Moving items to a folder - To move items to a folder or between folders, select

Options

→

Move to folder

(not shown if there are no folders available). When you select

Move to folder

, a list of available folders opens and you can also see the root level of the application (for moving an item out of a folder). Select the location you want the item to be moved to and press

OK

.

• Sending items - To send items, to compatible devices, scroll to the item that you want to send, select

Options

→

Send

. Select the method, the choices are

Via multimedia

,

Via

Bluetooth

, and

Via e-mail

.

• If you choose to send the item in an e-mail or a multimedia message, an editor opens.

Press to select the recipient(s) from the Contacts directory or write the phone number or e-mail address of the recipient in the

To

: field. Add text or sound and select

Options

→

Send

. See “Writing and sending messages” on page 50.

• Via Bluetooth.

See “Sending data via Bluetooth” on page 113.

Copyright protections may prevent some images, ringing tones, and other content from being copied, modified, transferred or forwarded.

Volume control

When you have an active call or are listening to a sound, press or to increase or decrease the volume level, respectively.

The loudspeaker allows you to speak and listen to the phone from a short distance without having to hold the phone to your ear, for example, having it on a table nearby. The loudspeaker can be used during a call, with sound and video applications, and when viewing multimedia messages. Sound and video applications use the loudspeaker by default. Using the loudspeaker makes it easier to use other applications while in a call.

Voice volume icons:

- for earpiece mode,

- for loudspeaker mode.


13

Fig. 3 Volume indicators for earpiece and loudspeaker modes are shown in the navigation bar.

To start using the loudspeaker during an already active call, select

Options

→

Activate loudsp.

. A tone is played, is shown in the navigation bar, and the volume indicator changes.

The loudspeaker cannot be activated when you have connected a headset to the phone.

Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely loud.

To turn off the loudspeaker when you have an active call, select

Options

→

Activate handset

.

Shared memory

The following features in this device may share memory: contacts, text messages, and multimedia messages, images and ringing tones, Video recorder, RealPlayer TM , calendar and to-do notes, and downloaded applications. Use of one or more of these features may reduce the memory available for the remaining features sharing memory. For example, saving many multimedia messages may use all of the available memory. Your device may display a message that the memory is full when you try to use a shared memory feature.

In this case, delete some of the information or entries stored in the shared memory features before continuing. Some of the features, such as calendar and to-do notes may have a certain amount of memory specially allotted to them in addition to the memory shared with other features.

14


Your phone

Making a call

1 In standby mode, key in the phone number, including the area code. Press or to move the cursor. Press to remove a number.

• For international calls, press twice for the international prefix (the + character replaces the international access code) and then key in the country code, the area code without 0, and the phone number.

2 Press to call the number.

3 Press to end the call (or to cancel the call attempt).

Pressing will always end a call, even if another application is active and displayed.

When the keypad lock is on, calls still may be possible to the official emergency number programmed into your device. Key in the emergency number and press .

You can make a call using your voice so that you do not need to look at the display to key in the number.

See “Voice dialling” on page 24.

Making a call using the Contacts directory

1 To open the Contacts directory, go to

Menu

→

Contacts

.

2 To find a contact, scroll to the desired name, or key in the first letters of the name. The

Search field opens automatically and matching contacts are listed.

3 Press to start the call.

If the contact has more than one phone number, scroll to the number and press to start the call.

Fig. 4 Making a call.


15

To view the speed dialling grid, go to

Menu

→

Tools

→

Speed dial

.

Calling your voice mailbox (Network Service)

The voice mailbox is an answering service where callers who are unable to reach you can leave you voice messages.

• To call your voice mailbox, press and in standby mode.

• If the phone asks for the voice mailbox number, key it in and press

OK

. You can obtain this number from your service provider.

See “Diverting calls (Network Service)” on page 18.

Each phone line may have its own voice mailbox number. See “Line in use (Network

Service)” on page 68.

Changing the voice mailbox number

To change the phone number of your voice mailbox, go to

Menu

→

Tools

→

Voice mailbox

and select

Options

→

Change number

. Key in the number (obtained from your service provider) and press

OK

.

Speed dialling a phone number

1 Assign a phone number to one of the speed dialling keys (

“Assigning speed dialling keys” on page 25.

- ).

See

2 To call the number: In standby mode, press the corresponding speed dialling key and

. If the

Speed dialling

function is set to

On

: Press and hold the corresponding speed dialling key until the call is started.

Making a conference call (Network Service)

Your Nokia 6670 phone supports conference calling with up to six participants. See

Fig. 5 on page 17.

16


1 Make a call to the first participant.

2 To make a call to a new participant, select

Options

→

New call

. Key in or search the memory for the phone number of the participant and press

Call

. The first call is automatically put on hold.

3 When the new call has been answered, join the first participant in the conference call.

Select

Options

→

Conference

.

4 To add a new person to the call, repeat step 2 and then select

Options

→

Conference

→

Add to conference

.

• To have a private conversation with one of the participants: Select

Options

→

Conference

→

Private

. Scroll to the desired participant and press

Private

. The conference call is put on hold in your phone, and the other participants can still continue talking with each other while you have a private discussion with one participant only. Once you have finished the private conversation, press

Cancel

to return to the conference call.

• To drop one participant from the conference call, select

Options

→

Conference

→

Drop participant

, then scroll to the participant and press

Drop

.

5 To end the active conference call, press .

Fig. 5 Conference call with two participants.

Answering a call

• To answer an incoming call, press .

• To end the call, press .

If you do not want to answer a call, press . The caller will hear a ’line busy’ tone.

When a call comes in, press

Silence

to quickly mute the ringing tone.

Options during a call

Press

Options

during a call for some of the following options:


17

Fig. 6 Options during a call.

Go to

Menu

→

Settings

→

Call divert

.

Mute

or

Unmute

,

End active call

,

End all calls

,

Hold

or

Unhold

,

New call

,

Conference

,

Private

,

Drop participant

,

Answer

, and

Reject

.

Swap

is used to switch between the active call and the call on hold.

Transfer

is used to connect an incoming call or a call on hold with an active call and to disconnect yourself from both calls.

Send DTMF

is used to send DTMF tone sequences, for example, passwords or bank account numbers.

You may not have all of these options. Contact your service provider for more details.

1 Key in the digits with - . Each keystroke generates a DTMF tone, which is transmitted while the call is active. Press repeatedly to produce: *, p (inserts a pause of approximately two seconds before, or between DTMF characters.), and w (if you use this character, the remaining sequence is not sent until you press

Send

again during the call). Press

2 To send the tone, press

OK

.

to produce #.

Call waiting (Network Service)

If you have activated the Call waiting service, the network will notify you of a new incoming call while you have a call in progress.

1 During a call, press to answer the waiting call. The first call is put on hold.

To switch between the two calls, press

Swap

.

2 To end the active call, press .

Diverting calls (Network Service)

When this network service is activated, you can direct your incoming calls to another number, for example, to your voice mailbox number. For details, contact your service provider.

18


• Select one of the divert options, for example, select

If busy

to divert voice calls when your number is busy or when you reject incoming calls.

• Select

Options

→

Activate

to set the divert setting on,

Cancel

to set the divert setting off, or

Check status

to check whether the divert is activated or not.

• To cancel all active diverts, select

Options

→

Cancel all diverts

.

See “Essential indicators in standby mode” on page 10.

You cannot have barring of incoming calls and call diverting active at the same time. See

“Call barring (Network Service)” on page 72.

Log - Call register and general log

In the log you can monitor phone calls, text messages, packet data connections, and data calls registered by the phone. You can filter the log to view just one type of event and create new contact cards based on the log information.

Connections to your remote mailbox, multimedia messaging centre, or browser pages are shown as data calls or packet data connections in the general communications log.

GPRS data counter

The GPRS data counter allows you to check the amount of data sent and received during packet data (GPRS) connections. This can be beneficial as you may be charged for your

GPRS connections by the amount of data sent and received.

Recent calls register

The phone registers the phone numbers of missed, received, and dialled calls, and the approximate duration of your calls. The phone registers missed and received calls only if the network supports these functions, and the phone is switched on and is within the network’s service area.

Go to

Menu

→

Log

.

Go to

Menu

→

Log

→

GPRS counter

.

Go to

Menu

→

Log

→

Recent calls

.


19

Options in the

Missed, Received, Dialled views:

Call

,

Create message

,

Use number

,

Request presence

,

Delete

,

Clear list

,

Add to

Contacts

,

Help

, and

Exit

.

Missed calls and received calls

To view a list of the last 20 phone numbers from which somebody has tried to call you without success (Network Service), go to

Log

→

Recent calls

→

Missed calls

.

Tip! When you see a note in standby mode about missed calls, press

Show

to access the list of missed calls. To call back, scroll to the number or name you want and press

.

To view a list of the 20 numbers or names from which you have most recently accepted calls (Network Service), go to

Log

→

Recent calls

→

Received calls

.

Dialled numbers

To view the 20 phone numbers that you have most recently called or attempted to call, go to

Log

→

Recent calls

→

Dialled nos.

.

Erasing recent call lists

• To clear all recent call lists, select

Options

→

Clear recent calls

in the Recent calls main view.

• To clear one of the call registers, open the register you want to erase and select

Options

→

Clear list

.

• To clear an individual event, open a register, scroll to the event, and press .

Fig. 7 The Dialled numbers view.

Go to

Menu

→

Log

→

Call duration

.

Call duration

Allows you to view the duration of your incoming and outgoing calls.

Note: The actual time invoiced for calls by your service provider may vary, depending on network features, rounding off for billing, and so forth.

Erasing call duration timers - Select

Options

→

Clear timers

. For this you need the lock

code. See “Security” on page 74.

20


Viewing the general log

In the general log, for each communication event, you can see the sender or recipient name, phone number, name of the service provider, or access point.

See Fig. 8 on page 21.

Sub-events, such as a text message sent in more than one part and packet data connections, are logged as one communication event.

Filtering the log

1 Select

Options

→

Filter

. A list of filters opens.

2 Scroll to a filter and press

Select

.

Erasing the contents of the log

• To erase all the log contents, Recent calls register, and Messaging delivery reports permanently, select

Options

→

Clear log

. Confirm by pressing

Yes

.

Packet data counter and connection timer

• To view how much data, measured in kilobytes, has been transferred and how long a certain GPRS connection has lasted, scroll to an Incoming or Outgoing event with the access point icon and select

Options

→

View details

.

Log settings

• Select

Options

→

Settings

. The list of settings opens.

•

Log duration

- The log events remain in the phone memory for a set number of days after which they are automatically erased to free memory.

If you select

No log

, all the log contents, Recent calls register, and Messaging delivery reports are permanently deleted.

•

Show call duration

.

See “Call duration” on page 20.

Go to

Menu

→

Log

and press .

Fig. 8 General log of communication events.


21

Personal information

Options in the

Contacts main view:

Open

,

Call

,

Create message

,

New contact

,

Open conversation

,

Edit

,

Delete

,

Duplicate

,

Add to group

,

Belongs to groups

,

Mark/Unmark

,

Copy to

SIM direct.

,

Go to web address

,

Send

,

Contacts info

,

SIM directory

,

Service numbers

,

Settings

,

Help

, and

Exit

.

Options when editing a contact card:

Add thumbnail

/

Remove thumbnail

,

Add detail

,

Delete detail

,

Edit label

,

Help

, and

Exit

.

Contacts

In Contacts, you can store and manage contact information, such as names, phone numbers, and addresses.

You can also add a personal ringing tone, voice tag, or a thumbnail image to a contact card.

You can create contact groups, which allow you to send text messages or e-mail to many recipients at the same time.

Contact information can only be sent to or received from compatible devices.

Creating and editing contact cards

1 Press in standby mode or go to

Menu

→

Contacts

.

2 Open Contacts and select

Options

→

New contact

.

3 Fill in the fields you want and press

Done

.

• To edit contact cards,

See “Actions common to all applications” on page 12.

• To delete contact cards, in the Contacts directory, scroll to the contact card and select

Options

→

Delete

.

• To attach a small thumbnail image to a contact card, open a contact card, select

Options

→

Edit

and then select

Options

→

Add thumbnail

. The thumbnail image is also shown when the contact is calling you. After you attach a thumbnail image to a contact card, you can select

Add thumbnail

to replace the image with a different thumbnail or

Remove thumbnail

to remove the thumbnail from the contact card.

22


• To assign default numbers and addresses to a contact card, open a contact card and select

Options

→

Defaults

. A pop-up window opens, listing the different options.

Copying contacts between the SIM card and phone memory

• To copy names and numbers from a SIM card to your phone, select

Options

→

SIM directory

, scroll to the name(s) you want to copy and select

Options

→

Copy to

Contacts

.

• If you want to copy a phone, fax, or pager number from Contacts to your SIM card, go to Contacts, open a contact card, scroll to the number, and select

Options

→

Copy to

SIM direct.

Adding a ringing tone for a contact card or group

You can set a ringing tone for each contact card and group. When that contact or group member calls you, the phone plays the chosen ringing tone (if the caller’s telephone number is sent with the call and your phone recognises it).

1 Press to open a contact card or go to the Groups list and select a contact group.

2 Select

Options

→

Ringing tone

. A list of ringing tones opens.

3 Use the scroll key to select the ringing tone you wish to use for the contact or group and press

Select

.

• To remove the ringing tone, select

Default tone

from the list of ringing tones.

Tip! For an individual contact, the phone uses the ringing tone that was assigned last. So, if you first change a group ringing tone and then the ringing tone of a single contact that belongs to that group, the ringing tone of the single contact is used.


23

Voice dialling

You can make a phone call by saying a voice tag that has been added to a contact card.

Any spoken word(s) can be a voice tag.

• When recording, hold the phone at a short distance away from your mouth. After the starting tone, clearly pronounce the word, or words, you want to record as a voice tag.

Before using voice tags, note that:

• Voice tags are not language-dependent. They are dependent on the speaker's voice.

• You must say the name exactly as you said it when you recorded it.

• Voice tags are sensitive to background noise. Record voice tags and use them in a quiet environment.

• Very short names are not accepted. Use long names and avoid similar names for different numbers.

Note: Using voice tags may be difficult in a noisy environment or during an emergency, so you should not rely solely upon voice dialling in all circumstances.

Adding a voice tag to a phone number

Voice tags can only be added to phone numbers stored in the phone’s memory.

See

“Copying contacts between the SIM card and phone memory” on page 23.

1 In the Contacts main view, scroll to the contact that you want to add a voice tag to, and press to open the contact card.

2 Scroll to the number that you want to add the voice tag to, and select

Options

→

Add voice tag

.

3 Press

Start

to record a voice tag. After the starting tone, clearly pronounce the word(s) you want to record as a voice tag.

4 After recording, the phone plays the recorded tag and the note

Playing voice tag

is displayed.

5 When the voice tag has been successfully saved, the note

Voice tag saved

is displayed and a beep sounds. A symbol can be seen next to the number in the contact card.

24


Making a call by saying a voice tag

1 In standby mode, press and hold is displayed.

. A short tone is played and the note

Speak now

2 When you are making a call by using a voice tag, hold the phone at a short distance away from your mouth and face and pronounce the voice tag clearly.

3 The phone plays the original voice tag, displays the name and number, and after a few seconds dials the number of the recognised voice tag.

• If the phone plays the wrong voice tag, or you want to retry voice dialling, press

Retry

.

Voice dialling cannot be used when a data call or a GPRS connection is active.

Assigning speed dialling keys

Speed dialling is a quick way to call frequently used numbers. You can assign speed dialling keys to eight phone numbers. Number 1 is reserved for the voice mailbox.

1 Open the contact card for which you want a speed dialling key and select

Options

→

Assign speed dial

. The speed dialling grid opens, showing you the numbers from 1-9.

2 Scroll to a number and press

Assign

. When you return to the contact information view, you can see the speed dial icon next to the number.

• To call the contact by speed dialling, go to standby mode and press the speed dialling key and .

Viewing subscribed contacts

In the Contacts directory, scroll right to the second tab to open the subscribed contacts list. This list allows you to view presence data, including availability and instant messaging

(chat) status, for all subscribed contacts.

See “Presence (Network Service)” on page 26.

See

“Chat (Network Service)” on page 94.

Options in the

Subscribed contacts view:

Open

,

Call

,

Create message

,

Open conversation

,

Unsubscribe

,

Subscribe new

,

Mark/Unmark

,

My Presence

,

Settings

,

Help

, and

Exit

.


25

Options in the

Groups list view:

Open

,

New group

,

Delete

,

Rename

,

Ringing tone

,

Contacts info

,

Settings

,

Help

, and

Exit

.

Managing contact groups

Creating contact groups

1 In the Contacts directory, press to open the Groups list.

2 Select

Options

→

New group

.

3 Write a name for the group or use the default name

Group 1

and press

OK

.

Adding members to a group

1 In the Contacts directory, scroll to the contact you want to add to a group and select

Options

→

Add to group:

. A list of available groups opens.

2 Scroll to the group to which you want to add the contact and press .

Go to

Menu

→

Extras

→

Presence

.

Options in the

Presence view:

Open

,

My availability

,

Viewers

,

Update presence

,

Login

,

Logout

,

Settings

,

Help

, and

Exit

.

Presence (Network Service)

Use Presence to inform others when, where and how you want to be contacted. Presence allows you to view and create a dynamic profile of your contact details, visible to other users of the service, to share information or control services. Presence information can include your availability, whether you prefer people to call or send messages, where you are and what you are doing.


Before you can use Presence, you need to find a service that you want to use and then save the settings of that service. You may receive the settings in a special text message, called

a smart message, from the service provider that offers the Presence service. See “Receiving smart messages” on page 52.

For more information, contact your service provider.

The Presence application allows you to change your own published information and manage who is authorised to see your presence. To view the presence information of others, you must use Contacts.

See “Contacts” on page 22.

26


Changing your availability information

Select

Options

→

My availability

and select:

•

Available

- You are available for people to call or send you messages, for example, your

phone is in general profile. See “Profiles” on page 84.

•

Busy

- You may be available for people to call or send you messages, for example, your phone is in meeting profile.

•

Not available

- You are not available for people to call or send you messages, for example, your phone is in silent profile.

Changing who can view your Presence information

Select

Options

→

Viewers

and select:

•

Public pres.

- Displays limited information, for managing ways for people to contact you.

This is available to anyone you have not blocked.

•

My availability

- Select

Available

,

Busy

, or

Not available

.

•

Viewers

- Opens the

Current viewers

view of your

Public pres.

.

See “Public viewers” on page 28.

•

Update presence

- Updates your presence information to the presence server.

•

Login

/

Logout

- Connect to or disconnect from the presence server.

See “Chat and

Presence servers” on page 100.

•

Settings

- To manage the publishing of your presence information.

•

Private pres.

- Displays private information, so you can share more personal information.

This is only available to those that you have authorised to view your private information. You can select the following options:

•

My availability

- Select

Available

,

Busy

, or

Not available

.

•

My presence msg.

- You can write a text message of up to 40 characters to describe your current availability.

•

My presence logo

- You can add a logo to your availability information. Logo files are stored in the Gallery.

See “Gallery” on page 41.

Fig. 9 The Private

Presence view.


27

•

Viewers

- Opens the

Private list

view of your

Private pres.

.

See “Private viewers” on page 28.

•

Update presence

- Updates your presence information to the presence server.

•

Login

/

Logout

- Connect to or disconnect from the presence server.

See “Chat and

Presence servers” on page 100.

•

Settings

- To manage the publishing of your presence.

•

Blocked pres.

- Displays a screen containing no personal details.

See “Blocked viewers” on page 29.

Public viewers

Go to

Public pres.

and select

Options

→

Viewers

→

Current viewers

to see the names, phone numbers, or user IDs of the viewers who you do not allow to view your private presence messages, but who are currently viewing your public presence. You can scroll to a viewer, press

Options

, and select:

•

Add to private list

- Allows the viewer to also see your private presence.

•

Block

- Prevents the viewer from seeing your presence information.

•

Add to contacts

- Adds the viewer to your Contacts directory.

•

Refresh lists

- Connect to the presence server to update the viewer lists. This option is only available when you are offline.

Private viewers

Go to

Private pres.

and select

Options

→

Viewers

→

Private list

to see the names, phone numbers, or user IDs of the viewers who you allow to view your private presence messages.

To prevent a viewer from seeing your private presence messages, scroll to the viewer and press . You can scroll to a viewer, press

Options

, and select:

•

Add new

- Add a new viewer manually or from your Contacts directory.

You can only select a contact who has a user ID in the contact card.

•

Block

- Prevents the viewer from seeing your presence information.

•

Add to contacts


28


•

Remove from list

- Removes the viewer from the private list. The option is available also when there are marked items as selected. If the list is empty the option is not available.

•

View details

- Shows the user ID information of the viewer.

•

Refresh lists


Blocked viewers

Go to

Options

→

Viewers

→

Blocked pres.

to see the viewers you prevented from seeing your public and private presence messages. To allow a viewer to see your presence information, scroll to a viewer and press . You can scroll to a viewer, press

Options

, and select:

•

Add to private list

- Allows the viewer to also see your private presence.

•

Add new

- Add a new viewer manually or from your Contacts directory.

You can only select a contact who has a user ID in the contact card.

•

Add to contacts


•

View details

- Shows the user ID information of the viewer.

•

Refresh lists


Updating your Presence information

Go to

Menu

→

Extras

→

Presence

.

Once the connection has been established:

1 Key in your user ID and password and press to login.

You obtain the user ID and password from your service provider.

2 Select

Options

→

Update presence

. The option is available when you are logged into the server and have changed your presence information in

Private pres.

or

Public pres.

view and not updated it.

3 To logout, select

Options

→

Logout

.


29

Go to

Menu

→

Tools

→

Positioning

.

Presence settings

Select

Options

→

Settings

from the Presence main menu.

See “Chat and Presence servers” on page 100.

•

Show to

- Select:

•

Private & public

- Both public and private presence is published.

•

Private viewers

- Only private viewers can see your presence information.

•

Public viewers

- Both public and private viewers see your public presence information.

•

No one

- Your presence information is not published.

•

Sync. with Profiles

- Defines which Presence attributes are changed when you change your profile. Select:

•

Off

- The presence attributes are not changed, even if you change your profile.

•

On

- Both

My availability

and

My presence msg.

are changed when you change your profile.

•

Availability only

-

My presence msg.

is not changed when you change your profile.

•

Private msg. only

-

My availability

is not changed when you change your profile.

Positioning (Network Service)

Positioning

allows the network to detect the position of your phone. By enabling or disabling

Positioning

, you choose when your position information is provided to the network.

To enable

Positioning

in your phone, select

Settings

→

Positioning

→

On

.

When you receive a

Position request

, a message is displayed showing the service that is making the request. Press

Accept

to allow your position information to be sent, or press

Reject

to deny the request.

Position request

messages are logged in the

Recv. requests

list. To view them, select

Menu

→

Positioning

→

Recv. requests

. The icon beside each request indicates whether the request is

30


new, rejected, or accepted. If you want to see details of a request, scroll to the request and press . If you want to clear the

Recv. requests

list, select

Options

→

Clear list

.

Calendar

In Calendar, you can keep track of your appointments, meetings, birthdays, anniversaries, and other events. You can also set a calendar alarm to remind you of upcoming events.

Calendar uses shared memory.

See “Shared memory” on page 14.

Creating calendar entries

1 Go to

Menu

→

Calendar

2 Select

Options

→

New entry

and select:

•

Meeting

to remind you of an appointment that has a specific date and time.

•

Memo

to write a general entry for a day.

•

Anniversary

to remind you of birthdays or special dates. Anniversary entries are repeated every year.

3 Fill in the fields. Use the scroll key to move between fields.

•

Subject

/

Occasion

- Write a description of the event.

•

Location

- The place of a meeting, optional.

•

Start time

,

End time

,

Start date

, and

End date

.

•

Alarm

- Press to activate the fields for

Alarm time

and

Alarm date

.

•

Repeat

- Press to change the entry to be repeating. Shown with in the Day view.

•

Repeat until

- You can set an ending date for the repeated entry, for example, the ending date of a weekly course you are taking. This option is shown only if you have selected to repeat the event.

•

Synchronisation

-

Private

- After synchronisation the calendar entry can be seen only by you and it will not be shown to others even if they have online access to view the calendar.

Public

- The calendar entry is shown to others who have access to view your


31

32

Options in the different calendar views:

Open

,

New entry

,

Week view

/

Month view

,

Delete

,

Go to date

,

Send

,

Settings

,

Help

, and

Exit

.

calendar online.

None

- The calendar entry will not be copied when you synchronise your calendar.

4 To save the entry, press

Done

.

If you are editing or deleting a repeated entry, choose how you want the changes to take effect:

All occurrences

- all repeated entries are changed /

This entry only

- only the current entry will be changed.

Calendar views

Press in the Month, Week, or Day views to automatically highlight today’s date.

To write a calendar entry, press any number key ( - ) in any calendar view.

A Meeting entry is opened and the characters you keyed in are added to the

Subject

field.

• To go to a certain date, select

Options

→

Go to date

. Write the date and press

OK

.

• Icons in Day and Week views: -

Memo

, and -

Anniversary

.

• Synchronisation icons in Month view:

-

Private

,

None

, and - the day has more than one entry.

To-do

In To-do you can keep a list of tasks that you need to do. The To-do list uses shared memory.


Go to

Menu

→

To-do

.

1 To start to write a to-do note, press any digitkey ( and the cursor blinks after the letters you have keyed in.

- ). The editor opens

2 Write the task in the

Subject

field. Press to add special characters.

• To set the due date for the task, scroll to the

Due date

field and key in a date.

• To set a priority for the to-do note, scroll to the

Priority

field and press .

3 To save the to-do note, press

Done

. If you remove all characters and press

Done

, the note will be deleted, even if you edit a previously saved note.

• To open a to-do note, scroll to it and press .

• To delete a to-do note, scroll to it and select

Options

→

Delete

or press .


• To mark a to-do note as completed, scroll to it and select

Options

→

Mark as done

.

• To restore a to-do note, select

Options

→

Mark as not done

.

Importing data from compatible Nokia phones

You can move calendar, contacts, and to-do data from compatible Nokia phones to your phone using the Nokia PC Suite 6.3 Content Copier application on a compatible PC.

Instructions for using the application can be found in the help function of PC Suite on the

CD-ROM.


33

Multimedia

Press in standby mode or go to

Menu

→

Camera

.

Camera

With the

Camera

application you can take pictures and record videos while on the move.

The images are automatically saved in the Gallery application, where you can rename them and organise them in folders. You can also send images in a multimedia message, as an email attachment, or via a Bluetooth connection. The camera produces JPEG images and video clips are recorded in the 3GPP file format with the .3gp file extension.

Options before taking a picture:

Capture

,

Activate night mode

/

Deact. night mode

,

Go to

Gallery

,

Self-timer

,

Settings

,

Help

, and

Exit

.

Taking pictures

1 Press in standby mode and press or to move to the

Image

tab. The

Camera

application opens and you can see the view to be captured.

You can see the viewfinder and the cropping lines, which show you the image area to be captured.

You can also see the image counter, which shows you how many images, depending on the selected picture quality, fit in the memory of your phone or memory card, if you use one.

2 Press to zoom in on your subject before taking the picture. Press to zoom out again. The zoom indicator on the display shows the zoom level.

Tip! The resolution of a zoomed picture is lower than that of a non-zoomed picture, but the image remains the same size. You may notice the difference in image quality if viewed on a PC, for example.

3 To take a picture, press . Do not move the phone before the

Camera

application starts to save the image. The image is saved automatically in the Gallery.


34


Tip! To take a photo immediately after another, select

Options

→

Settings

→

Image

→

Show captured image

. Select

No

. The photos do not remain on the display after being taken, are saved in the Gallery, and the camera is ready for use again.

Camera

goes into battery saving mode if there have been no key presses within a minute.

To continue taking pictures, press .

After the image has been saved:

• If you do not want to save the image, select

Options

→

Delete

.

• To return to the viewfinder to take a new picture, press .

You can insert an image into a contact card. See “Creating and editing contact cards” on page 22.

Self-timer

Use the self-timer to delay the taking of a picture, so that you can include yourself in the picture.

1 Select

Options

→

Self-timer

.

2 Select the delay

10 seconds

,

20 seconds

, or

30 seconds

.

3 Press

Activate

. The camera will take the picture after the selected delay has elapsed.

Settings

In the

Camera

application settings, you can adjust the image quality setting, select whether photos remain on the display after being taken, change the default image name, and change the memory location of saved images.

1 Select

Options

→

Settings

→

Image

.

2 Scroll to the setting you want to change:

•

Image quality

-

High

,

Normal

, and

Basic

. The better the image quality, the more memory the image consumes.

•

Show captured image

- To take a photo immediately after another, select

No

. The photos do not remain on the display after being taken, are saved in the Gallery, and the camera is ready for use again.

Options after a picture has been taken:

New

,

Delete

,

Send

,

Set as wallpaper

,

Rename image

,

Go to Gallery

,

Settings

,

Help

, and

Exit

.


35

Options before recording a video:

Record

,

Activate night mode

/

Deact. night mode

,

Mute

/

Unmute

,

Go to Gallery

,

Settings

,

Help

, and

Exit

.

Options after you have recorded a video:

New

,

Play

,

Delete

,

Send

,

Rename

,

Go to Gallery

,

Settings

,

Help

, and

Exit

.

•

Default image name

- By default,

Camera

names images in the format ‘Image.jpg’.

Default image name

allows you to set a name for the images stored.

•

Memory in use

- Select whether you want to store your images in the phone memory or on the memory card, if you use one.

Recording videos

Press

Camera

in standby mode and press or to move to the

Video

tab.

• Press to start recording.

• To pause recording at any time, press . Press again, to resume recording.

• Press to zoom in on your subject before, or during, recording. Press to zoom out again.

• Press to stop recording.

The video clip is saved to either the phone’s memory or the memory card, depending on the setting of your

Memory in use

.

See “Setting up your Video recorder” on page 36.

• To immediately play the video clip you just recorded, select

Options

→

Play

.

• To play previously saved video clips, go to the Gallery.


Setting up your Video recorder

Use the following settings to define how videos are recorded.

1 Select

Options

→

Settings

→

Video

.

2 Scroll to the setting you want to change:

•

Length

- Select:

•

Maximum

- The length of the video recording is restricted to 10 minutes.

•

Short

- To record video clips up to 95 kB in size, which relates to approximately 10 seconds in duration, so that they can be conveniently sent as a multimedia message.

•

Video resolution

- Select 128x96 or 176x144.

•

Default video name

- Define a default name.

36


•

Memory in use

- Define the memory store. Choices are phone’s memory or memory card, if one is used.

Viewing images

Pictures taken with the

Camera

application are stored as images in the Gallery. See

“Gallery” on page 41.

Images can be sent to you in a multimedia or picture message, as an e- mail attachment, or via Bluetooth. After receiving an image in Inbox, you need to save it in the phone memory or on a memory card. You can save graphics sent to you in picture

messages to the Picture messages folder. See “Picture messages folder” on page 42.

Select an image from the list of images in the

Images

folder in the Gallery to start the image viewer and display the image.

When viewing an image, pressing or takes you to the next or previous image in the current folder.

In the images thumbnail view:

1 Press or to move between the phone and memory card.

2 To browse the list of images, press and .

3 Press to open an image. When the image is open, you can see the name of the image.

You can view animated GIF files in the same way as other images.

Options when viewing an image:

Send

,

Set as wallpaper

,

Rotate

,

Zoom in

,

Zoom out

,

Full screen

,

Delete

,

Rename

,

View details

,

Add to ’Go to’

,

Help

, and

Exit

.

Zooming on a saved image

1 Select

Options

→

Zoom in

or

Zoom out

. You can see the zooming ratio at the top of the display.

See “Keyboard shortcuts” on page 38.

2 Press to return to the initial view. The zooming ratio is not stored permanently.


37

38

Full screen

When you select

Options

→

Full screen

, the panes around the image are removed so that you can see more of the image. Press to return to the initial view.

Moving the focus

When you are zooming an image, use the scroll key to move the focus to the left, right, up, or down, so that you can take a closer look at one part of the image, for example, its upper right corner.

Keyboard shortcuts

•

•

• Rotate 90 degrees: not stored permanently.

- zoom in,

- anticlockwise, - clockwise. The rotation status is

- zoom out, press and hold to return to the normal view.

- change between full screen and normal view.

Go to

Menu

→

RealPlayer

.

RealPlayer™

With RealPlayer™, you can play local media files stored in the phone memory, or memory card, or stream media files over the air from a streaming link. The streaming link can be activated during a browsing session or stored in the phone memory, or memory card.

Media files are video, music or audio clips. Files with the extensions .3gp, .amr, .mp4, .ra,

.rv, .rm and .ram are supported by RealPlayer.

RealPlayer does not necessarily support all file formats or all the variations of a file formats. For example, RealPlayer will attempt to open all .mp4 files. However, some .mp4 files may include content that is not compliant with 3GPP standards and, therefore, is not supported by this phone. In this case, the operation might fail and result in partial playback or in an error message.

RealPlayer uses shared memory.



Playing media files

• To play a media file stored in your phone’s memory or memory card, select

Options

→

Open

and:

•

Most recent clips

- To play one of the last 6 files played in RealPlayer, or

•

Saved clip

- To play a file saved in the Gallery.


Scroll to a file and press to play the file.

• To stream content over the air:

• Select a streaming link saved in the Gallery. Before your live content begins streaming, your phone will connect to the site and load the file.

• Open the link to a file in the browser.

To stream live content, you must first configure your default access point.

See “Access points” on page 68.

Many service providers will require you to use an Internet Access Point (IAP) for your default access point. Other service providers allow you to use a WAP access point. Contact your service provider for more information.

In RealPlayer, you can only open an rtsp:// URL address. You cannot open an http:// URL address, however RealPlayer will recognise an http link to a .ram file since a .ram file is a text file containing a rtsp link.

Shortcuts during play

When a media file is playing use the scroll key to seek (move quickly through the media file), and to mute the sound, as follows:

Press and hold to seek forwards, or press and hold to seek backwards through the media file.

Press and hold until the indicator is displayed to mute the sound.

Press and hold until you see the indicator to turn on the sound.

Options in

RealPlayer when a clip has been selected (the available options may vary):

Play

,

Continue

,

Stop

,

Mute

,

Unmute

,

Clip details

,

Send

,

Settings

,

Help

, and

Exit

.


39

Changing the settings

Select

Options

→

Settings

then either

Video

,

Audio

or

Connection

.

Select

Video

to change the following settings:

•

Contrast

- Open the slider view to change the contrast.

•

Repeat

- Choose

On

to have the playing video file restart automatically once it has finished.

Select

Audio

to change the following settings:

•

Repeat

- Choose

On

to have the playing audio file restart automatically once it has finished.

•

Random play

- Choose

On

to select a random order for playlist items.

Select

Connection

to change the connection settings.

Go to

Menu

→

Movie director

.

Movie director

Use

Movie director

to create edited video clips which may contain video, sound, and text.

Editing is carried out automatically according to the style that you select. The style determines the transitions and visual effects that are used in the video clip.

Open

Movie director

and press or to move between the tab and the tab.

In the tab, you can select:

•

Quick muvee

- Creates video clips suitable to be sent via multimedia (MMS). You can select several video clips and the style you want to apply to them. The duration of the

Quick muvee

video clip is typically less than 10 seconds.

•

Custom muvee

- You can select video clips and apply a style, music and message, set the duration and preview the video clip before saving. Define the following:

•

Viideo

- Select the source file or files you want to use. Select

Mark/Unmark

,

Play

or

Capture

.

40


•

Style

- Select a style from the list. Styles determine the effects and message caption.

Each style is associated with default music and message text.

•

Music

- Select a music clip from the list.

•

Message

- Adds a caption to the beginning and ending of the video clip. You can enter a message or select one from the template. You can edit the default message text.

•

Create muvee

- You are prompted to set the duration for the video clip. Select

Multimedia message

to create a video size suitable to be sent via MMS,

Same as music

to create a video of the same duration as the selected music clip or

User defined

to manually enter the video duration.

After the video preview is prepared the

Preview muvee

view opens, where you can

Play

,

Recreate

(to make a new variation of the video clip) and

Save

the new video clip.

•

Style downloads

- Download and install new styles.

•

Settings

- Scroll to the setting you want to change:

•

Memory in use

- Select

Phone memory

or

Memory card

•

Resolution

- Select

High

,

Low

or

Automatic

•

Default muvee name

- Enter a default name for your video clips.

The tab contains a list of video clips that you can

Play

,

Send

,

Rename

and

Delete

.

Gallery

Use the Gallery to store and organise your images, sound clips, playlists, and video clips, streaming links and RAM files.

Gallery uses shared memory.


Open the Gallery to see a list of the folders in the phone memory. Press to see the folders on the memory card, if you use one.

Select a folder

Images

,

Sound clips

, or

Video clips

(or other folder that you have created) and press to open it.

In the open folder you can see:

Go to

Menu

→

Gallery

.


41

42

Options:

Open

(folder or item),

Send

,

Delete

,

Create new

,

Move to folder

,

Copy to folder

,

New folder

,

Mark/Unmark

,

Edit

,

Rename

,

Gallery downloads

,

Image uploader

,

View details

,


,

Settings

,

Help

, and

Exit

.

Options in the

Picture messages folder:

Open

,

Send

,

Delete

,

Mark/

Unmark

,

Rename

,

View details

,

Help

, and

Exit

.

• an icon depicting the type of each file in the folder, or in the case of an image, a small thumbnail picture; a preview of the image

• the name of the file

• the date and time a file was saved or the size of the file

• subfolders, if present.

You can browse, open, and create folders, mark, copy and move items to folders. See

“Actions common to all applications” on page 12.

The options vary according to the content of the list of media files.

Opening files

Select any file and press to open it. Each file will open in its corresponding application as follows:

• Images - Open in the Image viewer.

See “Viewing images” on page 37.

• Sound clips - Open and play in the RealPlayer application.

See “RealPlayer™” on page 38.

• Video clips, RAM files, and streaming links - Open and play in the RealPlayer

application. See “RealPlayer™” on page 38.

• Subfolders - Open to display contents.

Other default folders

Picture messages folder

Use this folder to store pictures sent to you in picture messages.

• Select the folder

Images

→

Picture msgs.

.

To save a picture that you have received in a picture message, go to

Messaging

→

Inbox

, open the message, and select

Options

→

Save picture

.


Wallpapers folder

Use this folder to store pictures that you want to use as background images for multimedia messages.


Images

→

Wallpapers

.

Presence logos folder

Use this folder to store logos for Presence.

See “Presence (Network Service)” on page 26.


Images

→

Presence logos

.

Downloading files

To download files into the Gallery using the browser:

• Select

Options

→

Gallery downloads

and choose from

Graphic downloads

,

Video downloads

, or

Tone downloads

. The browser opens and you can choose a bookmark for

the site to download from. See “Viewing bookmarks” on page 104.

To download files, you must first configure your default access point.


Once items have been downloaded, the browser closes and the phone returns to the Gallery view.

Uploading images to an image server (Network Service)

You can send your pictures to an image server to allow others to share your pictures online.

Before you can upload images, you must enter the settings for the image server.

See

“Setting up the image server” on page 44.

You can get these settings from your service

provider.

1 Select

Options

→

Image uploader

.

2 To begin an upload, mark the images and select

Upload

.


43

3 Enter a name for the folder on the image server that the images will be stored in and press .

Setting up the image server

1 Select

Settings

→

Image servers

and press

“Access points” on page 68.

2 Press .

. Fill in the details for each field.

See

44


Messaging

In Messaging you can create, send, receive, view, edit, and organise: text messages, multimedia messages, e-mail messages, and smart messages. Smart messages are special text messages that can be picture messages, or messages containing ring tones, configuration settings, bookmarks, contact details or calendar items. You can also receive messages and data via a Bluetooth connection, receive service messages, cell broadcast messages, and send service commands.

Note: Picture message function can be used only if it is supported by your network operator or service provider. Only devices that offer picture message features can receive and display picture messages.

Text messages and multimedia messages (MMS) use shared memory.


When you open Messaging, you can see the

New message

function and a list of default folders:

Inbox

- Contains received messages except e-mail and cell broadcast messages. Email messages are stored in the

Mailbox

. You can read cell broadcast messages by selecting

Options

→

Cell broadcast

.

My folders

- For organising your messages into folders.

Mailbox

- When you open this folder, you can either connect to your remote mailbox to retrieve your new e-mail messages or view your previously retrieved e-mail messages offline. After you have defined settings for a new mailbox, the name given to that mailbox will replace

Mailbox

in the main view.

See “Settings for e-mail” on page 60.

Drafts

- Stores draft messages that have not been sent.

Go to

Menu

→

Messaging

.

Options in the

Messaging main view:

Create message

,

Connect

(shown if you have defined settings for the mailbox), or

Disconnect

(shown if there is an active connection to the mailbox),

SIM messages

,

Cell broadcast

,

Service command

,

Settings

,

Help

, and

Exit

.


45

Sent

- Stores the last 20 messages that have been sent. You can change the number of messages to be saved.

See “Settings for the Other folder” on page 62.

Messages or data that have been sent via a Bluetooth connection are not saved in the Draft or Sent folders.

Outbox

- Is a temporary storage place for messages waiting to be sent.

Reports

(Network Service) - You can request the network to send you a delivery report of the text messages, smart messages, and multimedia messages you have sent. To turn on delivery report reception, select

Options

→

Settings

→

Text message

or


, scroll to

Receive report

, and select

Yes

.

Receiving a delivery report of a multimedia message that has been sent to an e-mail address might not be possible.

Note: When sending messages, your device may display the words "

Data Sent!

". This is an indication that the message has been sent by your device to the message centre number programmed into your device. This is not an indication that the message has been received at the intended destination. For more details about messaging services, check with your service provider.

Before you create a multimedia message, write an e-mail, or connect to your remote mailbox, you must have the correct connection settings in place.

See “Settings needed for e-mail” on page 51.

See “Settings needed for multimedia messaging” on page 51.

Writing text

Using traditional text input

The indicator is shown on the top right of the display when you are writing text using traditional text input.

46


• Press a number key ( - ), repeatedly until the desired character appears.

Note that there are more characters available for a number key than are printed on the key.

Icons:

and indicate the selected case. means that the first letter of the next word is written in upper case, and all other letters will automatically be written in lower case. indicates number mode.

• To insert a number, press and hold the number key.

To switch between letter and number mode, press and hold .

• If the next letter is located on the same key as the present one, wait until the cursor appears (or press to end the time-out period), and then key in the letter.

• If you make a mistake, press to remove a character. Press and hold to clear more than one character.

• The most common punctuation marks are available under . Press repeatedly to reach the desired punctuation mark.

Press to open a list of special characters. Use the scroll key to move through the list and press

Select

to select a character.

• To insert a space, press . To move the cursor to the next line, press times.

• To switch between upper and lower case, press .

three

Using predictive text input

You can key in any letter with a single keypress using the predictive text input. To activate predictive text input, press and select

Dictionary on

. This will activate predictive text input for all editors in the phone. The


indicator is shown at the top of the display.


47

48

Fig. 10 Predictive text input.

1 Write the desired word by pressing the keys - for one letter. The word changes after every key press.

. Press each key only once

For example, to write ‘Nokia’ when the English dictionary is selected, press

for N, for o, for k, for i, and for a.

The word suggestion changes after each key press.


2 When you have finished the word, check that it is correct.

• If the word is correct, you can confirm it by pressing or by pressing to insert a space. The underlining disappears and you can begin to write a new word.

• If the word is not correct, you have the following options:

• Press repeatedly to view the matching words the dictionary has found one by one.

• Press and select

Dictionary

→

Matches

to view a list of matching words. Scroll to the word you want to use and press to select it.

• If the ? character is shown after the word, the word you intended to write is not in the dictionary. To add a word to the dictionary, press

Spell

, key in the word (max. 32 letters) using traditional text input, and press

OK

. The word is added to the dictionary. When the dictionary becomes full, a new word replaces the oldest added word.

• To remove the ? and clear characters one by one from the word, press .

Tips on using predictive text input

• To erase a character, press . Press and hold to clear more than one character.

• To change between the different character cases Abc, abc, and ABC, press . Note that if you press twice quickly the predictive text input is turned off.

• To insert a number in letter mode, press and hold the desired number key, or press and select number mode, key in the numbers you want, and press

OK

.

• The most common punctuation marks are available under . Press repeatedly to reach the desired punctuation mark.


Press to open a list of special characters. Use the scroll key to scroll through the list and press

Select

to select a character. Or press and select

Insert symbol

.

The predictive text input will try to guess which commonly used punctuation mark

(.,?!‘) is needed. The order and availability of the punctuation marks depend on the language of the dictionary.

• Press repeatedly to view the matching words the dictionary has found one by one.

When a word has been entered with predictive text on, you can press , select

Dictionary

and select:

•

Matches

- To view a list of words that correspond to your key presses. Scroll to the desired word and press .

•

Insert word

- To add a word (max. 32 letters) to the dictionary by using traditional text input. When the dictionary becomes full, a new word replaces the oldest added word.

•

Edit word

- To open a view where you can edit the word, available only if the word is active (underlined).

•

Off

- To turn off predictive text input for all editors in the phone.

Writing compound words

• Write the first half of a compound word and confirm it by pressing . Write the last part of the compound word and complete the compound word by pressing to add a space.

Copying text to the clipboard

If you want to copy text to the clipboard, the following are the easiest methods:

1 To select letters and words, press and hold . At the same time, press or . As the selection moves, text is highlighted.

To select lines of text, press and hold . At the same time press or .

2 To end the selection, release pressing the scroll key while still holding .

3 To copy the text to the clipboard, while still holding , press

Copy

.


49

Or, release and then press it once to open a list of editing commands, for example,

Copy

or

Cut

.

If you want to remove the selected text from the document, press .

4 To insert the text into a document, press and hold and press

Paste

.

Or, press once and select

Paste

.

Options in the text message editor:

Send

,

Add recipient

,

Insert

,

Delete

,

Check contacts

,

Message details

,

Sending options

,

Help

, and

Exit

.

Writing and sending messages

Before you can create a multimedia message, or write an e-mail, or connect to your remote mailbox, you must have the correct connection settings in place.



1 Select

New message

. A list of message options opens. Select:

•

Create:

→

Text message

if you want to create a text message

To send a picture message, select

Options

→

Insert

→

Picture

.

Each picture message is made up of several text messages. Therefore, sending one picture message may cost more than sending one text message.

•

Create:

→


if you wish to send a multimedia message (MMS).


•

Create:

→

E-mail

to send e-mail. If you have not set up your e-mail account, you will be prompted to do so.

2 Press to select the recipient(s) from the Contacts directory or write the phone number or e-mail address of the recipient in the

To:

field if you are sending an MMS or e-mail to the recipient. Press to add a semicolon (;) to separate each recipient.

3 Press to move to the message field.

4 Write the message.

Your device supports the sending of text messages beyond the normal 160-character limit. If your message exceeds 160 characters, it will be sent as a series of two or more messages.

50


In the navigation bar, you can see the message length indicator counting backwards from 160. For example, 10 (2) means that you can still add 10 characters for the text to be sent as two messages.

Note that using special (Unicode) characters such as ë, â, á, ì take up more space.

• To add a media object to a multimedia message, select

Options

→

Insert new

→

Image

,

Sound clip

,

Video clip

or

Slide

. Select the item you wish to add.

5 To send the message, select

Options

→

Send

or press .

Settings needed for multimedia messaging

You may receive the settings as a smart message from your network operator or service

provider. See “Receiving smart messages” on page 52.

For availability of and subscription to data services, please contact your network operator or service provider.

• Go to

Messaging

→

Options

→

Settings

→


. Open

Access point in use

and select the access point you created. See “Settings for multimedia messages” on page 59.

Settings needed for e-mail

Before you can send, receive, retrieve, reply to, and forward e-mail to a separate e-mail account, you must:

• Configure an Internet Access Point (IAP) correctly. See “Connection settings” on page 68.

• Define your e-mail settings correctly.

See “Settings for e-mail” on page 60.

Follow the instructions given by your remote mailbox and Internet service provider.

Tip! Start to key in a name in the

To:

field and select

Options

→

Check contacts

. The phone will retrieve all matching entries from the Contacts directory. If only one entry is found, it is added automatically. If more than one entry is found, select a contact from the list.


51

Options in Inbox:

Open

,

Create message

,

Delete

,

Message details

,

Move to folder

,

Mark/

Unmark

,

Help

, and

Exit

.

Options in the

Objects view:

Open

,

Save

,

Send

,

Help

, and

Exit

.

Inbox - receiving messages

When there are unread messages in Inbox, the icon changes to .

In Inbox, the message icons tell you what kind of a message it is. Here are some of the icons that you may see:

for an unread text message and for an unread smart message

for an unread multimedia message

for an unread service message

for data received via Bluetooth

for an unknown message type.

Viewing multimedia objects

• To see what kinds of media objects have been included in the multimedia message, open the message and select

Options

→

Objects

. In the Objects view you can view files that have been included in the multimedia message. You can choose to save the file in your phone or to send it, for example, via Bluetooth to another compatible device.

Important: Multimedia message objects may contain viruses or otherwise be harmful to your device or PC. Do not open any attachment if you are not sure of the trustworthiness of the sender.

See “Certif. management” on page 76.

Receiving smart messages

Your phone can receive many kinds of smart messages, text messages that contain data

(also called Over-The-Air (OTA) messages). To open a received smart message, open Inbox, scroll to the smart message ( ), and press .

52


•

Picture message

- To save the picture in the

Picture messages

folder in the Gallery for later use, select

Options

→

Save picture

.

•

Business card

- To save the contact information, select

Options

→

Save business card

.

Tip: If certificates or sound files are attached to business cards, they will not be saved.

•

Ringing tone

- To save the ringing tone to the Gallery, select

Options

→

Save

.

•

Operator logo

- To save the logo, select

Options

→

Save

. The operator logo can now be seen in standby mode instead of the network operator’s own identification.

•

Calendar entry

- To save the invitation to Calendar, select

Options

→

Save to Calendar

.

•

Web message

- To save the bookmark, select

Options

→

Save to bookmarks

. The bookmark is added to the Bookmarks list in browser services.

If the message contains both browser access point settings and bookmarks, to save the data select

Options

→

Save all

. Or, select

Options

→

View details

to view the bookmark and access point information separately. If you do not want to save all data, select a setting or bookmark, open the details, and select

Options

→

Save to Settings

or

Save to bookmarks

depending on what you are viewing.

•

E-mail notification

- Tells you how many new e-mails you have in your remote mailbox.

An extended notification may list more detailed information such as subject, sender, attachments, and so on.

• In addition, you can receive a text message service number, voice mailbox number, profile settings for remote synchronisation, access point settings for the browser, multimedia messaging or e-mail, access point login script settings, or e-mail settings.

To save the settings, select

Options

→

Save to SMS sett.

,

Save to Voice mail

,

Save to

Settings

, or

Save to e-mail sett.

.

Receiving service messages (Network Service)

Service messages are notifications of, for example, news headlines and they may contain a text message or address of a browser service. For availability and subscription, contact your service provider.


53

My folders

In My folders you can organise your messages into folders, create new folders, and rename and delete folders.

Remote mailbox (Network Service)

When you open this folder, you can either connect to your remote mailbox to:

• retrieve new e-mail headings or messages, or

• view your previously retrieved e-mail headings or messages offline.

If you select

New message

→

Create:

→

E-mail

or

Mailbox

in the Messaging main view and you have not set up your e-mail account, you will be prompted to do so.


When you create a new mailbox, the name you give to the mailbox automatically replaces

Mailbox

in the Messaging main view. You can have several mailboxes (max. six).

Opening the mailbox

When you open the mailbox, you can choose whether you want to view the previously retrieved e-mail messages and e-mail headings offline or connect to the e-mail server.

• When you scroll to your mailbox and press , the phone asks you if you want to

Connect to mailbox?

Select

Yes

to connect to your mailbox or

No

to view previously retrieved e-mail messages offline.

• Another way to start a connection is to select

Options

→

Connect

.

Retrieving e-mail messages from the mailbox

• If you are offline, select

Options

→

Connect

to start a connection to a remote mailbox.

54


1 When you have an open connection to a remote mailbox, select

Options

→

Retrieve email

→:

•

New

- To retrieve all new e-mail messages to your phone.

•

Selected

- To retrieve only the e-mail messages that have been marked. Use the

Mark/

Unmark

→

Mark

/

Unmark

commands to select messages one by one. See “Actions common to all applications” on page 12.

•

All

- To retrieve all messages from the mailbox.

To cancel retrieving, press

Cancel

.

2 After you have retrieved the e-mail messages, you can continue viewing them online.

Select

Options

→

Disconnect

to close the connection and to view the e-mail messages offline.

3 To open an e-mail message, scroll to the e-mail you want to view and press . If the e-mail message has not been retrieved (arrow in the icon is pointing outwards) and you are offline and select

Open

, you will be asked if you want to retrieve this message from the mailbox.

• To view e-mail attachments, open a message that has the attachment indicator and select

Options

→

Attachments

. In the Attachments view, you can retrieve, open, or save attachments, in supported formats. You can also send attachments via

Bluetooth.

If your mailbox uses the IMAP4 protocol, you can decide whether to retrieve e-mail headings only, messages only, or messages and attachments. With the POP3

protocol, the options are e-mail headings only or messages and attachments. See

“Settings for e-mail” on page 60.

Important: Multimedia message objects may contain viruses or otherwise be harmful to your device or PC. Do not open any attachment if you are not sure of the trustworthiness of the sender.

Deleting e-mail messages

• To delete an e-mail from the phone while still retaining it in the remote mailbox:


55

Select

Options

→

Delete

→

Phone only

.

The phone mirrors the e-mail headings in the remote mailbox. So, although you delete the message content, the e-mail heading stays in your phone. If you want to remove the heading as well, you have to first delete the e-mail message from your remote mailbox and then make a connection from your phone to the remote mailbox again to update the status.

• To delete an e-mail from both the phone and the remote mailbox:

Select

Options

→

Delete

→

Phone and server

.

If you are offline, the e-mail will be deleted first from your phone. During the next connection to the remote mailbox, it will be automatically deleted from the remote mailbox.

If you are using the POP3 protocol, messages marked to be deleted are removed only after you have closed the connection to the remote mailbox.

Undeleting e-mail messages when offline

To cancel deleting an e-mail from both the phone and server, scroll to an e-mail that has been marked to be deleted during the next connection ( ), and select

Options

→

Undelete

.

Disconnecting from mailbox

When you are online, select

Options

→

Disconnect

to end the data call or GPRS connection to the remote mailbox.

Outbox

Outbox is a temporary storage place for messages that are waiting to be sent.

Status of the messages in Outbox:

•

Sending

- A connection is being made and the message is being sent.

56


•

Waiting

/

Queued

- For example, if there are two similar types of messages in Outbox, one of them is waiting until the first one is sent.

•

Resend at

(time) - Sending has failed. The phone will try to send the message again after a time-out period. Press

Send

if you want to restart the sending immediately.

•

Deferred

- You can set documents to be ‘on hold’ while they are in Outbox. Scroll to a message that is being sent and select

Options

→

Defer sending

.

•

Failed

- The maximum number of sending attempts has been reached. If you were trying to send a text message, open the message and check that the Sending settings are correct.

Viewing messages on a SIM card

Before you can view SIM messages, you need to copy them to a folder in your phone. See


Cell broadcast (Network Service)

You may be able to receive messages on various topics, such as weather or traffic conditions from your service provider. For available topics and relevant topic numbers, contact your service provider. In the main view you can see:

• the status of the topic: - for new, subscribed messages and - for new, unsubscribed messages.

• the topic number, topic name, and whether it has been flagged ( ) for follow-up. You will be notified when messages belonging to a flagged topic have arrived.

A packet data (GPRS) connection may prevent cell broadcast reception. Contact your network operator for the correct GPRS settings.

In the Messaging main view, select

Options

→

Cell broadcast

.

Options in Cell broadcast:

Open

,

Subscribe

/

Unsubscribe

,

Hotmark

/

Remove hotmark

,

Topic

,

Settings

,

Help

, and

Exit

.


57

58

Service command editor

Select

Messaging

→

Options

→

Service command

. Key in and send service requests (also known as USSD commands) such as activation commands, for network services, to your service provider.

Options when editing message centre settings:

New msg. centre

,

Edit

,

Delete

,

Help

, and

Exit

.

Messaging settings

Settings for text messages

Go to

Messaging

and select

Options

→

Settings

→

Text message

to open the following list of settings:

•

Message centres

- Lists all the message centres that have been defined.

•

Msg. centre in use

(Message centre in use) - Defines which message centre is used for delivering text messages and smart messages such as picture messages.

•

Receive report

(delivery report) - When this network service is set to

Yes

, the status of the sent message (

Pending

,

Failed

,

Delivered

) is shown in the Reports (Network Service).

Receiving a delivery report of a multimedia message that has been sent to an e-mail address might not be possible.

•

Message validity

- If the recipient of a message cannot be reached within the validity period, the message is removed from the message service centre. Note that the network must support this feature.

Maximum time

is the maximum amount of time allowed by the network.

•

Message sent as

- The options are

Text

,

Fax

,

Paging

, and

E-mail

. For further information, contact your network operator.

Tip: Change this option only if you are sure that your message centre is able to convert text messages into these other formats.

•

Preferred connection

- You can send text messages via the normal GSM network or via

GPRS, if supported by the network.


•

Reply via same ctr.

(network service) - By setting this option to

Yes

, if the recipient replies to your message, the return message is sent using the same message service centre number. Note that this may not work between all operators.

Settings for multimedia messages

Go to

Messaging

and select

Options

→

Settings

→



•


(

Must be defined

) - Select which access point is used as the preferred connection for the multimedia message centre.


If you receive multimedia message settings in a smart message and save them, the received settings are automatically used for the Access point.

See “Receiving smart messages” on page 52.

•

Multimedia reception

- Select:

•

Only in home net.

- If you want to receive multimedia messages only when you are in your home network. When you are outside your home network, multimedia message reception is turned off.

•

Always on

- If you always want to receive multimedia messages.

•

Off

- If you do not want to receive multimedia messages or advertisements at all.

Tip: If the settings

Only in home net.

or

Always on

have been selected, your phone can make an active data call or GPRS connection without your knowledge

•

On receiving msg.

- Select:

•

Retr. immediately

- If you want the phone to try to retrieve multimedia messages instantly. If there are messages with Deferred status, they will be retrieved as well.

•

Defer retrieval

- If you want the multimedia messaging centre to save the message to be retrieved later. When you want to retrieve the message, set

On receiving msg.

to

Retr. immediately

.


59

Options when editing e-mail settings:

Editing options

,

New mailbox

,

Delete

,

Help

, and

Exit

.

•

Reject message

- If you want to reject multimedia messages. The multimedia message centre will delete the messages.

•

Allow anon. messages

- Select

No

, if you want to reject messages coming from an anonymous sender.

•

Receive adverts

- Define whether you want to allow reception of multimedia message advertisements or not.

•

Reports

- Set to

Yes

, if you want the status of the sent message (

Pending

,

Failed

,

Delivered

) to be shown in the Reports.

•

Deny report sending

- Choose

Yes

, if you do not want your phone to send delivery reports of received multimedia messages.

•

Message validity

(Network Service) - If the recipient of a message cannot be reached within the validity period, the message is removed from the multimedia message centre.

Maximum time

is the maximum amount of time allowed by the network.

•

Image size

- Define the size of the image in a multimedia message. The options are:

Small

(max. of 160*120 pixels) and

Large

(max. 640*480 pixels).

Settings for e-mail

Go to

Messaging

and select

Options

→

Settings

→

E-mail

.

Open

Mailbox in use

to select which mailbox you want to use.

Settings for Mailboxes

Select

Mailboxes

to open a list of mailboxes that have been defined. If no mailboxes have been defined, you will be prompted to do so. The following list of settings is shown (this information is available from your e-mail service provider):

•

Mailbox name

- Write a descriptive name for the mailbox.

•


(

Must be defined

) - The Internet Access Point (IAP) used for the

mailbox. Choose an IAP from the list. See “Connection settings” on page 68.

60


•

My e-mail address

(

Must be defined

) - Write the e-mail address given to you by your service provider. The address must contain the @ character. Replies to your messages are sent to this address.

•

Outgoing mail server:

(

Must be defined

) - Write the IP address or host name of the computer that sends your e-mail.

•

Send message

(Network Service) - Define how e-mail is sent from your phone.

Immediately

- A connection to the mailbox is started immediately after you have selected

Send

.

During next conn.

- E-mail is sent when you connect to your remote mailbox the next time.

•

Send copy to self

- Select

Yes

to save a copy of the e-mail to your remote mailbox and to the address defined in

My e-mail address

.

•

Include signature

- Select

Yes

if you want to attach a signature to your e-mail messages and to start to write or edit a signature text.

•

User name:

- Write your user name, given to you by your service provider.

•

Password:

- Write your password. If you leave this field blank, you will be prompted for the password when you try to connect to your remote mailbox.

•

Incoming mail server:

(

Must be defined

) - The IP address or host name of the computer that receives your e-mail.

•

Mailbox type:

- Defines the e-mail protocol your remote mailbox service provider recommends. The options are

POP3

and

IMAP4

.

This setting can be selected only once and cannot be changed if you have saved or exited from the mailbox settings.

•

Security

- Used with the POP3, IMAP4, and SMTP protocols to secure the connection to the remote mailbox.

•

APOP secure login

- Used with the POP3 protocol to encrypt the sending of passwords to the remote e-mail server. Not shown if IMAP4 is selected for

Mailbox type:

.

•

Retrieve attachment

(not shown if the e-mail protocol is set to POP3) - To retrieve e-mail with or without attachments.

•

Retrieve headers

- To limit the number of e-mail headers you want to retrieve to your phone. The options are

All

and

User defined

. Used with the IMAP4 protocol only.


61

Settings for service messages

When you go to

Messaging

and select

Options

→

Settings

→

Service message

, the following list of settings opens:

•

Service messages

- Choose whether or not you want to allow reception of service messages.

•

Authentic. needed

- Choose if you want to receive service messages only from authorised sources.

Settings for Cell broadcast (Network Service)

Check with your service provider whether Cell broadcast is available and what the available topics and related topic numbers are. Go to

Messaging

→

Options

→

Settings

→

Cell broadcast

to change the settings:

•

Reception

-

On

or

Off

.

•

Language

-

All

allows you to receive cell broadcast messages in every possible language.

Selected

allows you to choose in which languages you wish to receive cell broadcast messages. If the language you prefer could not be found in the list, select

Other

.

•

Topic detection

- If you receive a message that does not belong to any of the existing topics,

Topic detection

→

On

allows you to save the topic number automatically. The topic number is saved to the topic list and shown without a name. Choose

Off

if you do not want to save new topic numbers automatically.

Settings for the Other folder

Go to

Messaging

and select

Options

→

Settings

→

Other


•

Save sent messages

- Choose if you want to save a copy of every text message, multimedia message, or e-mail that you have sent to the Sent items folder.

62


•

No. of saved msgs.

- Define how many sent messages will be saved to the Sent items folder at a time. The default limit is 20 messages. When the limit is reached, the oldest message is deleted.

•

Memory in use

- Define the memory store. Choices are phone’s memory or memory card, if one is used.


63

64

Tools

Go to

Menu

→

Setting Wizard

.

Using the Setting Wizard

Use the Setting Wizard to configure your phone’s settings to enable you to use the browsers and to send and receive Multimedia Messages and e-mails. Because the Setting

Wizard configures GPRS and other settings for WAP, MMS and Internet access, the application should be run before manually configuring any other browser or messaging settings.

Ensure that all other applications are closed.

Select

Options

→

Open

. When you run the application for the first time, you will be asked to accept the Disclaimer in the End User Licence Agreement.

After accepting the Disclaimer, the Setting Wizard displays the instruction screen. Press

OK

to continue or

Exit

to return to the application menu.

The Setting Wizard automatically detects your network operator by reading the details from your SIM card. If the Setting Wizard does not recognise your SIM card, you will be asked to select your country and network operator from a list.

Select

Options

→

Change

to access the country list. Once the country is selected, you may then choose the network operator.

Scroll down to highlight the Operator. Select

Options

→

Change

to access the network operator list.

Once the country and operator have been chosen, select

Options

→

OK

.

The Setting Wizard will then confirm that you want to create the settings for your chosen network operator. Select

OK

to proceed or

Cancel

to return to the country and network operator lists.


The Setting Wizard will then program your phone. Progress bars will be visible for approximately 5-10 seconds. Your phone is now configured for MMS, WAP and Internet access. Select

OK

to close the Setting Wizard.

Please note that to use these services, you may have to contact your network operator or service provider to activate GPRS. Where possible, the Setting Wizard will display the telephone number to call.

Please note that not all network operators support all services.

E-mail configuration settings can be sent directly to your phone via Nokia’s Phone Settings web site at http://www.nokia.com/phonesettings.

Should you experience any problems with the Setting Wizard, please visit Nokia’s Phone

Settings web site at http://www.nokia.com/phonesettings to have your network operator’s latest settings sent directly to your phone via a text message.

Settings

Changing general settings

1 Scroll to a setting group and press to open it.

2 Scroll to a setting you want to change and press to:

• switch between options if there are only two (On/Off),

• open a list of options or an editor,

• open a slider view and press or to increase or decrease the value respectively.

See Fig. 11 on page 67. You may be able to receive some settings from your service

provider in a short message.


Go to

Menu

→

Settings

.


65

Phone settings

General

•

Phone language

- You can change the language for the display texts in your phone. This change may also affect the format used for date and time and the separators used, for example, in calculations. If you select

Automatic

, the phone selects the language according to the information on your SIM card. After you have changed the display text language, you must restart the phone.

Changing the settings for

Phone language

or

Writing language

affects every application in your phone and the change remains effective until you change these settings again.

•

Writing language

- You can change the writing language of your phone. Changing the language affects:

• the characters available when you press any key (

• the predictive text dictionary used

- )

• the special characters that are available when you press the and keys.

•

Dictionary

- To set predictive text input

On

or

Off

for all editors in the phone. Select a language for entering predictive text from the list available. You can also change this setting when you are in an editor. Press and select

Dictionary

→

Dictionary on

or

Off

.

•

Welcome note or logo

- The welcome note or logo is displayed briefly each time you switch on the phone. Select

Default

if you want to use the default image or animation.

Select

Text

to write a welcome note (max. 50 letters). Select

Image

to select a photo or picture from the Gallery.

•

Orig. phone settings

- You can reset some of the settings to their original values. To do this, you need the lock code.

See “Security” on page 74.

After resetting the settings, the phone may take a longer time to power on. All documents and files that you have created are left as they are.

66


Standby mode

•

Left selection key

and

Right selection key

- You can change the shortcuts that appear over the left and right selection keys in standby mode. In addition to the applications, you can have the shortcut point to a function, for example,

New message

.

•

Navigation key right

,

Navigation key left

,

Navigation key down

,

Navigation key up

, and

Selection key

- To have shortcuts available in standby mode when you press the scroll key in any direction, scroll to the desired application or function and press the scroll key.

Display

•

Screen saver timeout

- The screen saver is activated when the screen saver time-out period is over. When the screen saver is active, the display is cleared and you can see the screen saver bar.

• To deactivate the screen saver press any key.

Call settings

Send my caller ID (Network Service)

• This allows you to set your phone number to be displayed (

Yes

) or hidden (

No

) from the person to whom you are calling. Or, the value may be set by your network operator or service provider when you make a subscription.

Call waiting (Network Service)

• The network will notify you of a new incoming call while you have a call in progress.

Select

Activate

to request the network to activate call waiting,

Cancel

to request the network to deactivate call waiting, or

Check status

to check if the function is active or not.

Automatic redial

• When this setting is activated, your phone will make a maximum of ten attempts to connect the call after an unsuccessful call attempt. Press to stop automatic redialling.

Fig. 11 The Settings main view.


67

68

Summary after call

• Activate this setting if you want the phone to briefly display the approximate duration of the last call.

Speed dialling

• Select

On

and the numbers assigned to the speed dialling keys ( - ) can

be dialled by pressing and holding the key. See “Assigning speed dialling keys” on page 25.

Anykey answer

• Select

On

, and you can answer an incoming call by briefly pressing any key, except

Line in use (Network Service)

• This setting is shown only if the SIM card supports two subscriber numbers, that is, two phone lines. Select which phone line (

Line 1

or

Line 2

) you want to use for making calls and sending short messages. Calls on both lines can be answered irrespective of the selected line.

You will not be able to make calls if you select

Line 2

and have not subscribed to this network service.

To prevent line selection, select

Line change

→

Disable

if supported by your SIM card. To change this setting, you need the PIN2 code.

Connection settings

Access points

Here you can see a short explanation for every setting that may be needed for different data connections and access points. If you have not yet used your phone to make a WAP connection, you may need to contact your service provider for assistance with the firsttime connection or visit www.nokia.com/phonesettings.


Many service providers will require you to use an IAP for your default access point. Other service providers allow you to use a WAP access point. Contact your service provider for more information.

Start to fill in the settings from the top because depending on what data connection you select (

Data bearer

) only certain setting fields are available.

•

Connection name

- Give a descriptive name for the connection.

•

Data bearer

- The options are

GPRS

or

Data call

. Depending on what data connection you select, only certain setting fields are available. Fill in all fields marked with

Must be defined

, or with an asterisk. Other fields can be left empty, unless you have been instructed otherwise by your service provider.

To be able to use a data connection, the network operator or service provider must support this feature, and if necessary, activate it for your SIM card.

•

Access point name

(for packet data only) - The access point name is needed to establish a connection to the GPRS network. You obtain the access point name from your network operator or service provider.

•

Dial-up number

(for Data call only) - The modem telephone number of the access point.

•

User name

- Write a user name if required by the service provider. The user name may be needed to make a data connection, and is usually provided by the service provider.

The user name is often case-sensitive.

•

Prompt password

- If you must key in a new password every time you log onto a server, or if you do not want to save your password to the phone, choose

Yes

.

•

Password

- A password may be needed to make a data connection, and is usually provided by the service provider. The password is often case-sensitive. When you are writing the password, the characters you enter are shown briefly and then changed to asterisks (*). The easiest way to enter numbers is to press and hold the digit you want to enter, and then continue entering letters.

•

Authentication

-

Normal

/

Secure

.

•

Homepage

- Depending on what you are setting up, write either:

• the service address, or


69

70

• the address of the multimedia messaging centre.

•

Data call type

(for Data call only) -

Analogue

,

ISDN v.110

, or

ISDN v.120

defines whether the phone uses an analogue or digital connection. This setting depends on both your

GSM network operator and Internet Service Provider (ISP), because some GSM networks do not support certain types of ISDN connections. For details, contact your ISP. If ISDN connections are available, they establish connections more quickly than analogue methods.

•

Maximum data speed

(for Data call only) - The options are 9600 or 14400, depending on what you have chosen in

Data call type

. This option allows you to limit the maximum connection speed when GSM data is used. Higher data rates may cost more, depending on the service provider.

The speeds above represent the maximum speed at which your connection will operate.

During the connection, the operating speed may be less, depending on network conditions.

Options

→ Advanced settings

•

Phone IP address

- The IP address of your phone.

•

Primary name server

- The IP address of the primary DNS server.

•

Second. name server

- The IP address of the secondary DNS server.

•

Proxy serv. address

- The IP address of the proxy server.

•

Proxy port number

- The port number of the proxy server.

If you need to enter these settings, contact your Internet service provider.

The following settings are shown if you have selected data call as the connection type:

•

Use callback

- This option allows a server to call you back once you have made the initial call. Contact your service provider to subscribe to this service.

The phone expects the callback call to use the same data call settings that were used in the callback-requesting call. The network must support that type of call in both directions, to and from the phone.

•

Callback type

- The options are

Use server no.

/

Use other no.

. Ask your service provider for the correct setting to use; it will depend on the service provider’s configuration.


•

Callback number

- Key in your phone’s data phone number which the dial back server uses. Usually, this number is the data call phone number of your phone.

•

Use PPP compression

- When set to

Yes

, this option speeds up the data transfer, if supported by the remote PPP server. If you have problems with establishing a connection, try setting this to

No

. Contact your service provider for guidance.

•

Use login script

- The options are

Yes

/

No

.

•

Login script

- Insert the login script.

•

Modem initialisation

(Modem initialisation string) - Controls your phone using modem

AT commands. If required, enter characters specified by your service provider or Internet service provider.

GPRS

The GPRS settings affect all access points using a packet data connection.

GPRS connection

- If you select

When available

and you are in a network that supports packet data, the phone registers to the GPRS network and sending short messages will be done via GPRS. Also, starting an active packet data connection, for example, to send and receive e-mail, is quicker. If you select

When needed

, the phone will use a packet data connection only if you start an application or action that needs it. The GPRS connection can be closed after it is not used by any application.

If there is no GPRS coverage and you have chosen

When available

, the phone will periodically try to establish a packet data connection.

Access point - The access point name is needed when you want to use your phone as a packet data modem to your computer.

Data call

The

Data call

settings affect all access points using a GSM data call.

Online time

- If there are no actions the data call is dropped automatically after a time-out period. The options are

User defined

, in which case you enter a time, or

Unlimited

.

Go to

Settings

→

Connection

→

GPRS

.

Go to

Settings

→

Connection

→

Data call

.


71

Date and time

The

Date and time

settings allow you to define the date and time used in your phone, as well as change the date and time format and separators.

•

Clock type

→

Analogue

or

Digital

- To change the clock shown in standby mode.

See

“Clock” on page 93.

•

Auto time update

- To allow the network to update time, date, and time zone information to your phone (Network Service). For the

Auto time update

setting to take effect, the phone needs to be restarted. Check any alarms as these may be affected by

Auto time update

.

•

Clock alarm tone

- To change the tone played when the clock alarm time is reached.

•

GMT offset

- To change the time zone for the clock time.

•

Daylight-saving

- To set daylight saving time on or off.

Call barring (Network Service)

Call barring allows you to restrict the making and receiving of calls with your phone. For this function, you need the barring password, which you can obtain from your service provider.

1 Scroll to one of the barring options.

2 Select

Options

→

Activate

to request the network to set call restriction on,

Cancel

to set the selected call restriction off, or

Check status

to check if the calls are barred or not.

• Select

Options

→

Edit barrings passw.

to change the barring password.

• Select

Options

→

Cancel all barrings

to cancel all active call barrings.

When calls are barred, calls still may be possible to certain official emergency numbers.

72


Network

Operator selection

• Choose

Automatic

to set the phone to automatically search for and select one of the cellular networks available in your area.

• Choose

Manual

, if you want to select the desired network manually from a list of networks. If the connection to the manually selected network is lost, the phone will sound an error tone and ask you to select a network again. The selected network must have a roaming agreement with your home network, that is, the operator whose SIM card is in your phone.

Cell info display

• Select

On

to set the phone to indicate when it is used in a cellular network based on

Micro Cellular Network (MCN) technology and to activate cell info reception (Network

Service).

Enhancement settings

Scroll to an enhancement folder and open the settings:

• Select

Default profile

to select the profile you want to activate each time you connect a certain enhancement to your phone.

See “Changing the profile” on page 84.

• Select

Automatic answer

to set the phone to answer an incoming call automatically after five seconds time when you connect a certain enhancement to your phone. If the

Incoming call alert

is set to

Beep once

or

Silent

, automatic answer cannot be used, and you must answer the phone manually.


73

Security

Phone and SIM

Explanations for the different security codes that may be needed:

• PIN code (4 to 8 digits) - The PIN (Personal Identification Number) code protects your

SIM card against unauthorised use. The PIN code is usually supplied with the SIM card.

After three consecutive incorrect PIN code entries, the PIN code is blocked. If the PIN code is blocked, you need to unblock the PIN code before you can use the SIM card again. See the information about the PUK code.

• PIN2 code (4 to 8 digits) - The PIN2 code, supplied with some SIM cards, is required to access some functions.

• Lock code (5 digits) - The lock code can be used to lock the phone and keypad to avoid unauthorised use.

The factory setting for the lock code is 12345. To avoid unauthorised use of your phone, change the lock code. Keep the new code secret and in a safe place separate from your phone.

• PUK and PUK2 codes (8 digits) - The PUK (Personal Unblocking Key) code is required to change a blocked PIN code. The PUK2 code is required to change a blocked PIN2 code.

If the codes are not supplied with the SIM card, contact the operator whose SIM card is in your phone for the codes.

You can change the following codes: lock code, PIN code, and PIN2 code. These codes can only include the numbers from 0 to 9.

Avoid using access codes similar to emergency numbers, such as 112, to prevent accidental dialling of the emergency number.

PIN code request

- When the PIN code request is active, the code is requested each time the phone is switched on. Note that deactivating the PIN code request may not be allowed by some SIM cards.

74


PIN code

/

PIN2 code

/

Lock code

- Open this setting if you want to change the code.

Autolock period

- You can set an autolock period, a time-out after which the phone is automatically locked and can be used only if the correct lock code is entered. Key in a number for the time-out in minutes or select

None

to turn off the autolock period.

• To unlock the phone, key in the lock code.

When the device is locked, calls still may be possible to the official emergency number programmed into your device.

Lock if SIM changed

- Select

Yes

if you want the phone to prompt for the lock code when an unknown, new SIM card is inserted into your phone. The phone maintains a list of SIM cards that are recognised as the owner’s cards.

Fixed dialling

- You can restrict your outgoing calls to selected phone numbers, if supported by your SIM card. You need the PIN2 code for this function. When this function is active, you can only call those phone numbers that are included in the fixed dialling list or which begin with the same digit(s) as a phone number on the list.

• Press to set

Fixed dialling

on.

When fixed dialling is activated, calls still may be possible to the official emergency number programmed into your device.

• To add new numbers to the Fixed dialling list, select

Options

→

New contact

or

Add from

Contacts

.

Closed user group

(Network Service) - You can specify a group of people to whom you can call and who can call you. For more information, contact your network operator or service provider. Select:

Default

to activate the default group agreed on with the network operator,

On

if you want to use another group (you need to know the group index number), or

Off

.

When calls are limited to closed user groups, calls still may be possible to the official emergency number programmed into your device.

Options in the

Fixed dialling view:

Open

,

Call

,

Activ. fixed dialling

/

Deact. fixed dialling

,

New contact

,

Edit

,

Delete

,

Add to

Contacts

,

Add from

Contacts

,

Find

,

Mark/

Unmark

,

Help

, and

Exit

.


75

Options in the certificate management main view:

Certificate details

,

Delete

,

Trust settings

,

Mark/Unmark

,

Help

, and

Exit

.

Confirm SIM services

(Network Service) - To set the phone to display confirmation messages when you are using a SIM card service.

Certif. management

In the Certificate management main view, you can see a list of authority certificates that have been stored in your phone. Press to see a list of personal certificates, if available.

Authority certificates are used by some browser services, such as banking services, for checking signatures or server certificates or other authority certificates.

Server certificates are used to improve security in the connection between the phone and the gateway. The phone receives the server certificate from the service provider before the connection is established and its validity is checked using the authority certificates saved in the phone. Server certificates are not saved.

Server certificates may be needed when you, for example:

• want to connect to an online bank or another site or remote server for actions that involve transferring confidential information, or

• want to decrease the risk of viruses or other malicious software and be sure of the authenticity of software when downloading and installing software.

Important: Note that even if the use of certificates makes the risks involved in remote connections and software installation considerably smaller, they must be used correctly in order to benefit from increased security. The existence of a certificate does not offer any protection by itself; the certificate manager must contain correct, authentic, or trusted certificates for increased security to be available. Certificates have a restricted lifetime. If

Expired certificate

or

Certificate not valid yet

is shown even if the certificate should be valid, check that the current date and time in your device are correct.

Before changing any certificate settings, you must make sure that you really trust the owner of the certificate and that the certificate really belongs to the listed owner.

76


Changing the trust settings of an authority certificate

• Scroll to an authority certificate and select

Options

→

Trust settings

. Depending on the certificate, a list of the applications that can use the selected certificate is shown. For example:

Application manager

/

Yes

- The certificate is able to certify the origin of new software.

Internet

/

Yes

- The certificate is able to certify e-mail and imaging servers.

Device manager

Device manager allows a third party, such as your service provider, to assist you directly with phone settings. To allow device management, your phone must establish a connection and synchronise with the third party’s server. You can start the synchronisation session from your phone, and you can accept or reject server-initiated synchronisation attempts.

This feature is operator dependent and may not be available on all phones. Contact your service provider for information and availability.

A device manager profile must be defined before you can connect to a server. The third party who is assisting you can help define the profile settings:

Server name

— Display name of the server.

Server ID

— Remote device manager server ID.

Server password

— Password used in server alerts. Enter the password that must be provided by the device manager server when synchronising with your phone.

Access point

— Internet access point your phone uses to establish the server connection.

Choose from the list of access points defined in your phone.

Host address

— Device management server URL.

Port

— Device management server port.

User name

— Your user name for this profile.

Go to

Menu

→

Tools

→

Device manager

Options in the

Device manager main view:

Start configuration

,

New server profile

,

Edit profile

,

Delete

,

Enable config.

/

Disable config.

,

View log

,

Help

, and

Exit

.


77

78

Password

— Your password for this profile.

Server will start configuration. Continue?

— Device management allowed on this server. Select

Yes

or

No

.

Auto-accept all reqs.

— Automatic or approved device management on this server. Select

Yes

to allow synchronisation without your verification, or select

No

to verify each synchronisation attempt.

Go to

Menu

→

Tools

→

File manager

Options in the File manager main view:

Open

,

Send

,

Delete

,

Move to folder

,

Copy to folder

,

New folder

,

Mark/Unmark

,

Rename

,

Find

,

View details

,

Memory details

,

Help

, and

Exit

.

File manager

In File manager you can browse, open, and manage files and folders in the phone memory or on the memory card, if you use one.

Open File manager to see a list of the folders in the phone memory. Press to see the folders on the memory card, if you use one.

You can browse, open, and create folders, mark, copy and move items to folders. See


Viewing memory consumption

If you have a memory card installed on your phone, you will have a choice of two memory views, one for the phone memory and one for the memory card.

Press or to move from one memory tab to another.

• To check memory consumption of the current memory select

Options

→

Memory details

.

The phone calculates the approximate amount of free memory for storing data and installing new applications.

In the memory views, you can view the memory consumption of the different data groups:

Calendar

,

Contacts

,

Documents

,

Messages

,

Images

,

Sound files

,

Video clips

,

Applications

,

Mem. in use

, and

Free memory

.


If the phone memory is getting low, remove some files, or move them to the memory card.

See “Troubleshooting” on page 120.

Voice commands

You can use Voice commands to start applications and profiles, and to dial numbers from

Contacts, without having to look at your phone’s display. You record a word, or words,

(voice command) and then pronounce this voice command to open an application, activate a profile, or dial a number.

You can have only one voice command per item.

Any spoken word(s) can be a voice command.

• When recording, hold the phone at a short distance away from your mouth. After the starting tone, clearly pronounce the word, or words, you want to record as a voice command.

Before using voice tags, note that:

• Voice tags are not language-dependent. They are dependent on the speaker's voice.

• You must say the name exactly as you said it when you recorded it.

• Voice tags are sensitive to background noise. Record voice tags and use them in a quiet environment.

• Very short names are not accepted. Use long names and avoid similar names for different numbers.

Note: Using voice tags may be difficult in a noisy environment or during an emergency, so you should not rely solely upon voice dialling in all circumstances.

Go to

Menu

→

Tools

→

Voice commands

.

Options in the

Voice commands main view:

Add voice command

,

Open

,

New application

,

Playback

,

Change

,

Delete

,

Delete all

,

Help

, and

Exit

.

Adding a voice command to an application

1 In the Voice commands main view, scroll to the application that you want to add a voice command to, and select

Options

→

Add voice command

.


79

To add a voice command to a profile, the Profiles folder must be opened and a specific profile selected.

2 The text

Press ’Start’, then speak after tone

is displayed.

• Press

Start

to record a voice command. The phone sounds a starting tone and the note

Speak now

is displayed.

3 Pronounce the voice command. The phone will stop recording after approximately 5 seconds.

4 After recording, the phone plays the recorded command and the note

Playing voice command

is displayed. If you do not want to save the recording, press

Quit

.

5 When the voice command has been successfully saved, the note

Voice command saved

is displayed and a beep sounds. A symbol can be seen next to the application.

Adding an application to the list

Assign voice commands to other applications that are not listed in the Voice commands main view.

1 In the Voice commands main view, select

Options

→

New application

.

2 Available applications are displayed. Scroll to the application that you want to add and press

Select

.

3 Add a voice command to the new application.

See “Adding a voice command to an application” on page 79.

Starting an application using a voice command

1 In standby mode, press and hold is displayed.

. A short tone is played and the note

Speak now

2 When you are starting an application by saying a voice command, hold the phone at a short distance away from your mouth and pronounce the voice command clearly.

3 The phone plays the original voice command and starts the application. If the phone plays the wrong voice command, press

Retry

.

80


Replaying, erasing, or changing a voice command

To replay, erase, or change a voice command, scroll to the item that has a voice command

(indicated by ), select

Options

, and then either:

•

Playback

- To listen to the voice command again.

•

Delete

- To erase the voice command.

•

Change

- To record a new voice command. Press

Start

to record.

Memory card

For details on inserting a memory card into the phone, see the Getting Started guide. You can use it to store your multimedia files such as video clips and sound files, photos, messaging data, and to backup information from your phone’s memory.

Included with your Nokia 6670 phone is a Reduced Size MultiMediaCard (RS-MMC) that may contain add-on applications from independent developers. These applications are designed by the devlopers to be compatible with your phone.

Details of how you can use the memory card with other features and applications of your phone are given in the sections describing these features and applications.

Keep all memory cards out of the reach of small children.

Use only compatible MultiMediaCards (MMC) with this device. Other memory cards, such as Secure Digital (SD) cards, do not fit in the MMC card slot and are not compatible with this device. Using an incompatible memory card may damage the memory card as well as the device, and data stored on the incompatible card may be corrupted.

Format memory card

When a memory card is formatted, all data on the card is permanently lost.

Go to

Menu

→

Tools

→

Memory card

..

Options in the memory card:

Backup phone mem.

,

Restore from card

,

Format mem. card

,

Memory card name

,

Set password

,

Change password

,

Remove password

,

Unlock memory card

,

Memory details

,

Help

, and

Exit

.


81

82

Some memory cards are supplied pre-formatted and others require formatting. When formatting, the memory card should always be formatted in your Nokia 6670 phone to ensure correct operation. The memory access and performance cannot be guaranteed when formatting with another operating system.

• Select

Options

→

Format mem. card

.

Select

Yes

to confirm. When formatting is complete, key a name for the memory card (max.

11 letters or numbers).

Backing up and restoring information

To back up information from your phone’s memory to the memory card, select

Options

→

Backup phone mem.

. To restore information from the memory card to the phone’s memory, select

Options

→

Restore from card

.

You can only back up the phone memory and restore it to the same phone.

Locking the memory card

To set a password to lock your memory card against unauthorised use, select

Options

→

Set password

.

You will be asked to enter and confirm your password. The password can be up to eight characters long.

The password is stored in your phone and you don’t have to enter it again while you are using the memory card on the same phone. If you want to use the memory card on another phone, you will be asked for the password.

Unlocking a memory card

If you insert another password-protected memory card in your phone, you will be prompted to enter the password of the card. To unlock the card:

• Select

Options

→

Unlock memory card

.


Once the password is removed, the memory card is unlocked and can be used on another phone without a password.

Checking memory consumption

You can check the memory consumption of different data groups and the available memory for installing new applications or software on your memory card:

• Select

Options

→

Memory details

.


83

Personalising your phone

Go to

Menu

→

Profiles

.

Options in the

Profiles main view:

Activate

,

Personalise

,

Create new

,

Delete profile

,

Tone downloads

,

Help

, and

Exit

.

Profiles

In Profiles, you can adjust and customise the phone tones for different events, environments, or caller groups. You can see the currently selected profile at the top of the display in standby mode. If the General profile is in use, only the current date is shown.

Changing the profile

1 Go to

Menu

→

Profiles

. A list of profiles opens.

2 In the Profiles list, scroll to a profile and select

Options

→

Activate

.

Shortcut! To change the profile, press in standby mode, scroll to the profile you want to activate and press

OK

.

Customising profiles

1 To modify a profile, scroll to the profile in the Profiles list and select

Options

→

Personalise

. To create a new profile, select

Options

→

Create new

. A list of profile settings opens.

2 Scroll to the setting you want to change and press to open the choices:

•

Ringing tone

- To set the ringing tone for voice calls, choose a ringing tone from the list.

Press any key to stop the sound. If a memory card is used, tones stored on it have the

icon next to the tone name. Ringing tones use shared memory.


You can also change ringing tones in Contacts. See “Adding a ringing tone for a contact card or group” on page 23.

84


•

Ringing type

- When

Ascending

is selected, the ringing volume starts from level one and increases level by level to the set volume level.

•

Ringing volume

- To set the volume level for the ringing and message alert tones.

•

Message alert tone

- To set the tone for messages.

•

Chat alert tone

- To set the tone for instant messages.

•

Vibrating alert

- To set the phone to vibrate at incoming voice calls and messages.

•

Keypad tones

- To set the volume level for keypad tones.

•

Warning tones

- The phone sounds a warning tone, for example, when the battery is running low of power.

•

Alert for

- To set the phone to ring only upon calls from phone numbers that belong to a selected contact group. Phone calls coming from people outside the selected group will have a silent alert. The choices are

All calls

/ (list of contact groups, if you have

created them). See “Creating contact groups” on page 26.

•

Availability

- Select

Available

,

Busy

, or

Not available

. See “Presence settings” on page 30.

•

User availab. alerts

- Key in a message to display your current presence status.

See

“Presence settings” on page 30.

•

Profile name

- You can rename a profile and give it any name you want. The General profile cannot be renamed.

Tip! When you scroll through the list, you can stop on a tone to listen to it before you make your selection.

Themes

You can change the look of your phone’s display by activating a theme. A theme can include the idle screen wallpaper, colour palette, screen saver, and background image in

’Go to’. Edit a theme for more detailed personalisation.

When you open

Themes

you will see a list of the available themes. The currently active theme is indicated by a check mark. Press to see the themes on the memory card, if you use one.

Go to

Menu

→

Themes

.

Options in the

Themes main view:

Preview

,

Apply

,

Edit

,

Theme downloads

,

Help

, and

Exit

.


85

86

Fig. 12 The Themes main view.

• To preview a theme, scroll to the theme and select

Options

→

Preview

to view the theme. Press to activate the theme. You can activate the theme without previewing it by selecting

Options

→

Apply

from the main view.

Tip! You can copy themes that you have downloaded. To copy a theme from your memory card to the phone memory, scroll to the theme and select

Options

→

Copy to phone mem.

. To copy a theme from your phone memory to the memory card, scroll to the theme and select

Options

→

Copy to mem. card

.

Editing themes

Group together elements from other themes, or images from the Gallery to personalise themes further.

1 Scroll to a theme, select

Options

→

Edit

, and select:

•

Wallpaper

- To select an image from one of the available themes, or select your own image from the Gallery, to use as a background image in standby mode.

•

Colour palette

- To change the colour palette used on the display.

•

Screen saver

- To select what is shown on the screen saver bar: the time and date or a text you have written yourself. The location and background colour of the screen saver bar changes in one minute intervals. Also, the screen saver changes to indicate the number of new messages or missed calls. You can set the time that elapses before the screen saver is activated.

See “Phone settings” on page 66.

•

Image in ’Go to’

- To select an image from one of the available themes, or select your own image from the Gallery, to use as a background image in Go to.

2 Scroll to the element to be edited and select

Options

→

Change

.

3 Select

Options

→

Set

to select the current setting. You can also preview the selected element by selecting

Options

→

Preview

. Note that you cannot preview all elements.

Restoring themes

To restore the currently selected theme back to its original settings, select

Options

→

Restore orig. theme

when editing a theme.


Extras

Wallet

Wallet provides you with a storage area for your personal information, such as credit and debit card numbers, addresses and other useful data, for example, user names and passwords.

The information stored in the wallet can be easily retrieved while browsing to automatically fill in online forms on browser pages, for example, when the service asks for credit card details. Data in the wallet is encrypted and protected with a wallet code that you define.

You can group wallet data into profiles that can be accessed, for example, for making purchases online.

Due to the nature of the wallet, it will automatically close after 5 minutes. Enter the wallet code to regain access to the contents. You can change this automatic time-out period, if required.

See “Wallet settings” on page 90.

Go to

Menu

→

Extras

→

Wallet

.

Entering the wallet code

Each time you open the wallet you will be prompted for a wallet code.

When you open the wallet for the first time, you must create your own access code:

1 Enter a code of your choice (4 - 10 alphanumeric characters), and press

OK

.

Fig. 13 The wallet main view.

Options in the wallet main view:

Open

,

Settings

,

Help

, and

Exit

.


87

2 You will be prompted to verify the code. Enter the same code and press

OK

. Do not give your wallet code to anyone else.

Enter the code that you have created and press

OK

.

If you enter the wallet code incorrectly on three consecutive occasions, the wallet application is blocked for five minutes. The block time increases if further incorrect wallet codes are entered.

If you forget your wallet code, you will have to reset the code, and you will lose all information stored in the wallet.

See “Resetting the wallet and wallet code” on page 91.

Storing personal card details

1 Select the

Cards

category from the main wallet menu and press .

2 Select a type of card from the list and press .

•

Payment cards

- Credit and debit cards.

•

Loyalty cards

- Membership and store cards.

•

Online acc. cards

- Personal user names and passwords to online services.

•

Address cards

- Basic contact details for home/office.

•

User info cards

- Customised personal preferences for online services.

3 Select

Options

→

Create new

. An empty form opens.

4 Fill in the fields and press

Done

.

You can also receive card information directly to the phone from a card issuer or service provider (if they offer this service). You will be notified which category the card belongs to.

Either save or discard the card. You can view and rename a saved card, but you cannot edit it.

You can open, edit or delete the fields in the card. Any changes will be saved upon exiting.

88


Creating personal notes

Personal notes are a means of storing sensitive information, for example, a bank account number. You can access the data in a personal note from the browser. You can also send a note as a message.

• Select the

Personal notes


• Select

Options

→

Create new

. An empty note opens.

• Press - to start writing. Press to clear characters. Press

Done

to save.

Options when viewing or editing card details:

Delete

,

Help

, and

Exit

.

Creating a wallet profile

Once you have stored your personal details, you can combine them together into a wallet profile. Use a wallet profile to retrieve wallet data from different cards and categories to the browser.

1 Select the

Wallet profiles


2 Select

Options

→

Create new

. A new wallet profile form opens.

3 Fill in the fields as indicated below and press

Done

.

Some of the fields must contain data selected from the wallet. You must save the data under the relevant category before creating a wallet profile, or the profile cannot be created.

•

Profile name

- Choose and enter a name for the profile.

•

Payment card

- Select a card from the Payment card category.

•

Loyalty card

- Select a card from the Loyalty card category.

•

Online access card

- Select a card from the Online acc. card category.

•

Shipping address

- Select an address from the Address card category.

•

Billing address

- By default this is the same as the Shipping address. If you require a different address, select one from the Address card category.

•

User info card

- Select a card from the User info card category.

•

Receive e-receipt

- Select a destination from the Address card category.


89

Options in the

Tickets main view:

View

,

Delete

,

Rename

,

Mark/

Unmark

,

Help

, and

Exit

.

•

Deliver e-receipt

- Select

To phone

,

To e-mail

, or

To pho. & e-mail

.

•

RFID sending

- Set to

On

or

Off

. Defines whether, or not, your unique phone identification is sent with the wallet profile (for future development dependent on

RFID-based ticketing).

Retrieving information from the wallet to your browser

When using online mobile services supporting the wallet functionality, you can upload the data stored in your wallet to automatically enter your details into an online form. For example, by uploading your payment card details you do not need to key in the card number and expiry date each time you need them (depending on the content being browsed). Also, you can retrieve your user name and password stored as an access card

when connecting to a mobile service that requires authentication. See “Purchasing an item” on page 106.

Viewing ticket details

You can receive notifications of tickets purchased online via the browser. Received notifications are stored in the wallet. To view the notifications:

1 Select the

Tickets


2 Select

Options

→

View

.

Wallet settings

Select

Options

→

Settings

from the main wallet menu:

•

Wallet code

- Change your wallet code. You will be prompted to enter the current code, create a new code, and verify the new code.

•

RFID

- Set the phone ID code, type, and sending options (for future development dependent on RFID-based ticketing).

90


•

Automatic close

- Change the automatic time-out period (1 - 60 minutes). After the time-out period has elapsed, the wallet code must be re-entered to gain access to the contents.

Resetting the wallet and wallet code

To reset both the contents of the wallet and the wallet code:

1 Key in *#7370925538# in standby mode.

2 Enter the phone’s lock code, and press

OK

.

See “Security” on page 74.

3 You will be asked to confirm the erasing of data. Press

OK

.

When opening the wallet again, you must enter a new wallet code. See “Entering the wallet code” on page 87.

Calculator

1 Enter the first number of your calculation. If you make a mistake, press to erase it.

2 Scroll to an arithmetic function and press to select it.

3 Enter the second number.

4 To execute the calculation, scroll to and press .

Note: This calculator has limited accuracy and is designed for simple calculations.

• To add a decimal, press .

• Press and hold to clear the result of the previous calculation.

• Use and to view previous calculations and move in the sheet.

Go to

Menu

→

Extras

→

Calculator

.

Options in

Calculator:

Last result

,

Memory

,

Clear screen

,

Help

, and

Exit

.

Converter

In Converter, you can convert measures such as

Length

from one unit to another, for example,

Yards

to

Metres

.

Go to

Menu

→

Extras

→

Converter

.


91

Options in

Converter:

Conversion type

,

Currency rates

(not applicable to other units),

Help

, and

Exit

.

The Converter has limited accuracy and rounding errors may occur.

Converting units

To make currency conversion you must first set the exchange rate. See “Setting a base currency and exchange rates” on page 92.

1 Scroll to the

Type

field and press to open a list of measures. Scroll to the measure you want to use and press

OK

.

2 Scroll to the first

Unit

field and press to open a list of available units. Select the unit from which you want to convert and press

OK

.

3 Scroll to the next

Unit

field and select the unit to which you want to convert.

4 Scroll to the first

Amount

field and key in the value you want to convert. The other

Amount

field changes automatically to show the converted value.

Press to add a decimal and press

(exponent) symbols.

for the +, - (for temperature), and E

The conversion order changes if you write a value in the second

Amount

field. The result is shown in the first

Amount

field.

Setting a base currency and exchange rates

Before you can make currency conversions, you need to choose a base currency (usually your domestic currency) and add exchange rates.

The rate of the base currency is always 1. The base currency determines the conversion rates of the other currencies.

1 Select

Currency

as the measure type and select

Options

→

Currency rates

. A list of currencies opens and you can see the current base currency at the top.

2 To change the base currency, scroll to the currency (usually your domestic currency), and select

Options

→

Set as base curr.

.

92


Tip: When you change the base currency, all previously set exchange rates are set to 0 and you need to key in new rates.

3 Add exchange rates, scroll to the currency, and key in a new rate, that is, how many units of the currency equal one unit of the base currency you have selected.

4 After you have inserted all the required exchange rates, you can make currency

conversions. See “Converting units” on page 92.

Notes

You can link notes to Go to and send them to other devices. Plain text files (TXT format) you receive can be saved to Notes.

• Press - to start to write. Press to clear letters. Press

Done

to save.

Go to

Menu

→

Extras

→

Notes

.

Clock

Changing clock settings

• To change the time or date, select

Options

→

Settings

in Clock.

Setting an alarm

1 To set a new alarm, select

Options

→

Set alarm

.

2 Enter the alarm time and press

OK

. When the alarm is active, the indicator is shown.

• To cancel an alarm, go to clock and select

Options

→

Remove alarm

.

Turning off the alarm

• Press

Stop

to turn off the alarm.

• Press

Snooze

to stop the alarm for five minutes, after which it will resume. You can do this a maximum of five times.

Go to

Menu

→

Extras

→

Clock

.

Options in Clock:

Set alarm

,

Reset alarm

,

Remove alarm

,

Settings

,

Help

, and

Exit

.


93

If the alarm time is reached while the phone is switched off, the phone switches itself on and starts sounding the alarm tone. If you press

Stop

, the phone asks whether you want to activate the phone for calls. Press

No

to switch off the phone or

Yes

to make and receive calls. Do not press

Yes

when wireless phone use is prohibited or when it may cause interference or danger

Personalising the alarm tone

1 To personalise the alarm tone, select

Options

→

Settings

.

2 Scroll to

Clock alarm tone

and press .

3 When you scroll through the list of tones, you can stop on a tone to listen to it before you make your selection. Press

Select

to select the current tone.

Go to

Menu

→

Extras

→

Recorder

.

Options in

Recorder:

Record sound clip

,

Delete

,

Rename sound clip

,

Send

,

Go to Gallery

,

Settings

,


,

Help

, and

Exit

.

Recorder

The voice recorder allows you to record telephone conversations and voice memos. If you are recording a telephone conversation, both parties will hear a tone every five seconds during recording.

Recorded files are stored in the Gallery.


• Select

Options

→

Record sound clip

and scroll to a function and press to select it.

Use: - to record, - to pause, - to stop, - to fast forward, - to fast rewind, or - to play an opened sound file.

Recorder cannot be used when a data call or a GPRS connection is active.

Go to

Menu

→

Extras

→

Chat

.

Chat (Network Service)

Chat allows you to converse with other people using instant messages, and join discussion forums (chat groups) with specific topics. Once you have registered with a chat service, you

can log into the service provider’s chat server. See Fig. 14 on page 95.

94


Check the availability of chat services, pricing, and tariffs with your network operator and/ or service provider. Service providers will also give you instructions on how to use their services.

Before using Chat

To access a chat service you need to save the settings for that service. You may receive the

settings from the network operator or service provider that offers the service. See

“Receiving smart messages” on page 52.

You can also key in the settings manually.

See

“Chat and Presence servers” on page 100.

Connecting to a chat server

1 Go to

Menu

→

Chat

to connect to a chat server. You can change the chat server to connect to.

See “Chat and Presence servers” on page 100.

2 Once the connection has been established, key in your user ID and password and press

, or press

Cancel

to stay offline. When you are offline, your phone is not connected to the chat server and you cannot send or receive messages. To log in later, select

Options

→

Login

.

You obtain the user ID and password from your service provider.

To log out, select

Options

→

Logout

.

Modifying your chat settings

Select

Options

→

Settings

→

Chat settings

.

•

Use screen name

- Select

Yes

to key in a nickname (max. 10 characters).

•

Chat presence

- To prevent others from seeing if you are online, select

Not active

.

•

Allow messages from

- Select

All

,

From chat contacts

or

None

.

•

Allow invitations from

- Select

All

,

From chat contacts

or

None

.

•

Message speed

- Select the speed at which new messages are displayed.

Options in the

Chat main view:

Open

,

Login

,

Logout

,

Settings

,

Help

, and

Exit

.

Fig. 14 The Chat main view.


95

Fig. 15 The Chat groups view.

Options in the

Chat groups view:

Open

,

Join group

,

Create new group

,

Leave chat group

,

Chat group

,

Search

,

Settings

,

Help

, and

Exit

.

•

Auto-reload availab.

- To choose how to update information about whether your chat contacts are online or offline. Select

Automatically

or

Manually

.

•

Reload user availab.

- Select

For all contacts

or

For sel. contacts

.

Joining and leaving a chat group

Go to the

Chat groups

view. A list of chat groups that you have saved or are currently

joined to is shown. See Fig. 15 on page 96. The icon next to a group indicates what type it

is:

• - A group that you have created and are currently joined to.

•

•

- A group that you have created but are not currently joined to.

- A group that you have saved and are currently joined to.

• - A group that you have saved but are not currently joined to.

• - A group that you are currently joined to but have not saved.

To join a chat group: Scroll to a group on the list and press . To join a chat group not on the list but for which you know the group ID, select

Options

→

Join group

. Key in the group ID and press .

You can scroll to a group, press

Options

→

Chat group

and then select:

Save group

,

Delete

,

View members

to see who are currently joined to the group,

Chat group details

to see the group ID, topic, members, editing rights in the group, and whether sending private messages is allowed in the group, and

Chat group settings

to view and edit the chat group’s settings.

See “Editing chat group settings” on page 99.

To leave the chat group: Select

Options

→

Leave chat group

.

96


Searching for chat groups and users

Go to the

Chat groups

view and select

Options

→

Search

→

Groups

or

Users

.

• You can search for

Groups

by

Group name

,

Topic

, and

Members

(user ID). For groups that you have found you can select

New search

,

Join

and

Save group

.

• You can search for

Users

by

User's name

,

User ID

,

Phone number

, and

E-mail address

. For users that you have found you can select

New search

,

Open conversation

,

Add to Chat contact

to save the contact,

Send invitation

, and

Add to blocked list

to block (or unblock) messages from the contact.

When the search result is displayed, you can select

Options

→

New search

,

More results

from the same search, and

Previous results

to see your previous search result.

Chatting in a chat group

Once you have joined a chat group, you can view the messages that are exchanged in the group, and send your own messages.

• To send a message, write the message and press .

• To send a private message to a member (if allowed in the group), select

Options

→

Send private msg.

, select the recipient, write the message, and press .

To reply to a private message sent to you, select

Options

→

Reply

.

To invite chat contacts who are online to join the chat group (if allowed in the group), select

Options

→

Send invitation

, select the contacts you want to invite, write the invitation message, and press

Done

.

Recording messages

To record the messages that are exchanged in a chat group or during an individual conversation, select

Options

→

Record convers.

. Key in the name for the message file and press . To stop recording, select

Options

→

Stop recording

.

The recorded message files are saved to Notes.

See “Notes” on page 93.

Options while chatting:

Send

,

Send private msg.

,

Reply

,

Send invitation

,

Leave chat group

,

Save group

,

Record convers.

/

Stop recording

,

Help

, and

Exit

.


97

Blocking messages

To prevent receiving messages from certain chat users, select

Options

→

Blocking options

and then select:

•

Add to blocked list

- To block messages from the currently selected user.

•

Add ID to list manually

- Key in the user ID of the user and press .

•

View blocked list

- To see the users whose messages are blocked.

•

Unblock

- Select the user that you want to remove from the blocked list and press .

Fig. 16 The Conversations view.

Options in the

Conversations view:

Send

,

Add to chat contact

,

Forward

,

Record convers.

/

Stop recording

,

Blocking options

,

End conversation

,

Help

, and

Exit

.

Icon: next to a user indicates that you have received a new message from that user.

Starting and viewing individual conversations

Go to the

Conversations

view for a list of the chat users with whom you have an ongoing

conversation. See Fig. 16 on page 98.

To start a new conversation, select

Options

→

New conversation

and then select:

•

Select recipient

- To see a list of your saved chat contacts that are currently online. Scroll to the contact and press .

•

Enter user ID

- Key in the user ID and press . The user ID is provided by the service provider to those who register to the service.

To view an ongoing conversation, scroll to the user and press . To continue the conversation, write your message and press . To return to the conversations list without closing the conversation, press

Back

.

To close the conversation, select

Options

→

End conversation

.

Ongoing conversations are automatically closed when you exit Chat.

To save a user to your chat contacts, scroll to the user and select

Options

→

Add to Chat contact

.

To send automatic replies to incoming messages, select

Options

→

Set auto reply on

. Key in the text and press

Done

.

98


Chat contacts

Go to the

Chat contacts

view to see a list of your saved chat contacts. is shown next to contacts that are currently online, and for contacts that are offline.

To create a new contact, select

Options

→

New chat contact

. Fill in the

Name

and

User ID

fields and press

Done

.

You can scroll to a contact and press to view contact details. Press

Options

and select:

•

Edit

- To edit the contact’s details.

•

Open conversation

- To start a new conversation or continue an ongoing conversation with the contact.

•

Switch tracking on

- To be notified every time the chat contact goes online or offline.

•

Belongs to groups

- To see which groups the chat contact has joined.

•


- To update information about whether contacts are online or offline. This option is not available if you have set the

Auto-reload availab.

to

Automatically

in

Chat settings

.

Editing chat group settings

You can edit the settings for a chat group if you have created the group or if the creator of the group has given you editing rights. Go to the

Chat groups

view, scroll to the desired group and select

Options

→

Chat group

→


.

See “Creating a new chat group” on page 99.

Creating a new chat group

Go to the

Chat groups

view and select

Options

→

Create new group

. Key in the settings for the group:

•

Group name

,

Group topic

, and a

Welcome note

that the participants see when they join the group.

•

Group size

- Maximum number of members allowed to join the group.

•

Allow search

- To define if others can find the chat group by searching.


99

Options in the

Chat contacts view:

Open

,

Open conversation

,

Switch tracking on

,

Belongs to groups

,

New chat contact

,

Edit

,

Delete

,


,

Blocking options

,

Search

,

Settings

,

Help

, and

Exit

.

•

Editing rights

- Scroll to the chat group members to whom you want to give editing rights and permission to invite contacts to join the group.

•

Group members

-

See “Restricting access to a chat group” on page 100.

•

Banned

- Displays a list of banned users.

•

Allow private msgs.

- To allow or prevent private messaging between members.

•

Group ID

- Is created automatically and cannot be changed.

Restricting access to a chat group

You can make a chat group closed by creating a

Group members

list. Only the users on the list are allowed to join the group. Go to the

Chat groups

view, scroll to the group and select

Options

→

Chat group

→


→

Group members

→

Selected only

.

• To add a user to the list, select

Add

and

Chat contact

or

Enter user ID

.

• To remove a user from the list, scroll to the user and select

Remove

.

• To clear the list and allow all chat users to join the group again select

Remove all

.

Chat and Presence servers

Select

Options

→

Settings

→

Server settings

. You may receive the settings as a smart message from the service provider that offers the chat service.

• To change the chat or presence server you wish to connect to, select

Server in use

.

• To change the Presence login type, select

Login type

and select

Automatic

,

Aut. in home net.

, or

Manual

.

• To change the Chat login type, select

Login type

and select

Automatic

or

Manual

.

• To add a new server, select

Options

→

New server

. Key in or select the settings:

Server name

and


to connect to the server,

Web address

of the chat server, your

User ID

and login

Password

. See “Connection settings” on page 68.

You obtain the user ID and password from your service provider when you register to the service. If you do not know your user ID or password, contact your service provider.

100


Go to

Use Go to for storing shortcuts, links to your favourite photos, video clips, notes, Recorder sound files, browser bookmarks, and saved browser pages.

The default shortcuts: - opens the Notes editor, - opens the Calendar to the current date, and - opens the Messaging Inbox.

Adding shortcuts

Shortcuts can be added only from pre-installed applications and functions. Not all applications have this functionality.

1 Open the application and scroll to the item that you want to add as a shortcut.

2 Select

Options

→


and press

OK

.

Shortcut! A shortcut in Go to is automatically updated if you move the item it is pointing to, for example, from one folder to another.

Using shortcuts:

• To open a shortcut, scroll to the icon and press . The file is opened in the corresponding application.

• To delete a shortcut, scroll to the shortcut you want to remove and select

Options

→

Delete shortcut

. Removing a shortcut does not affect the file it is referring to. The default shortcuts can not be deleted.

• To change the shortcut name, select

Options

→

Edit shortcut name

. Write the new name. This change affects only the shortcut, not the file or item the shortcut refers to.

Press

Go to

in standby mode or go to

Menu

→

Extras

→

Go to

.

Options in the Go to main view:

Open

,

Edit shortcut name

,

Move

,

List view

/

Grid view

,

Help

, and

Exit

.


101

Services and Applications

Go to

Menu

→

Web

or press and hold in standby mode.

Web (Mobile browser)

Various service providers maintain pages specifically designed for mobile phones, offering services that can be, for example, news, weather reports, banking, travel information, entertainment, and games. With the mobile browser you can view these services as WAP pages written in WML, XHTML pages written in XHTML, or a mixture of both. If you have not yet used your phone to make a WAP connection, you may need to contact your service provider for assistance with the first-time connection or visit www.nokia.com/ phonesettings.

A cache is a memory location that is used to store data temporarily. If you have tried to access or have accessed confidential information requiring passwords, empty the cache after each use. The information or services you have accessed is stored in the cache. To empty the cache, select

Options

→

Navigation options

→

Clear cache

.

Check the availability of services, pricing, and tariffs with your network operator and/or service provider. Service providers will also give you instructions on how to use their services.

Basic steps for accessing

• Save the settings that are needed to access the browser service that you want to use.

See “Setting up the phone for the browser service” on page 103.

• Make a connection to the service. See “Making a connection” on page 103.

• Start browsing the web pages. See “Browsing” on page 104.

• End the connection to the service.

See “Ending a connection” on page 107.

102


Setting up the phone for the browser service

Receiving settings in a smart message

You may receive service settings in a special text message, a so-called smart message, from the network operator or service provider that offers the service.


For more information, contact your network operator or service

provider.

Keying in the settings manually

Follow the instructions given to you by your service provider.

1 Go to

Settings

→

Connection

→

Access points

and define the settings for an access point.

See “Connection settings” on page 68.

2 Go to

Web

→

Options

→

Bookmark manager

→

Add bookmark

. Write a name for the bookmark and the address of the browser page defined for the current access point.

Making a connection

Once you have stored all the required connection settings, you can access browser pages.

There are three different ways to access browser pages:

• Select the homepage ( ) of your service provider.

• Select a bookmark from the Bookmarks view.

• Press the keys - to start to write the address of a browser service. The Go to field at the bottom of the display is immediately activated and you can continue writing the address there.

After you have selected a page or written the address, press to start to download the page.


103

Options in the

Bookmarks view (when a bookmark or folder is selected):

Open

,

Download

,

Back to page

,

Bookmark manager

,

Mark/

Unmark

,


,

Advanced options

,

Send

,

Find bookmark

,

Details

,

Settings

,

Help

, and

Exit

.

Viewing bookmarks

Your device may have some bookmarks loaded for sites not affiliated with Nokia. Nokia does not warrant or endorse these sites. If you choose to access them, you should take the same precautions, for security or content, as you would with any Internet site.

In the Bookmarks view, you can see bookmarks pointing to different kinds of browser pages. Bookmarks are indicated by the following icons:

- The starting page defined for the browser access point. If you use another browser access point for browsing, the starting page is changed accordingly.

- The last visited page. When the phone is disconnected from the service, the address of the last visited page is kept in memory until a new page is visited during the next connection.

When you scroll through bookmarks, you can see the address of the highlighted bookmark in the Go to field at the bottom of the display.

- A bookmark showing the title.

Adding bookmarks manually

1 In the Bookmarks view, select

Options

→

Bookmark manager

→

Add bookmark

.

2 Start to fill in the fields. Only the address must be defined. The default access point is

to enter special assigned to the bookmark if no other one is selected. Press characters such as /, ., :, and @. Press to clear characters.

3 Select

Options

→

Save

to save the bookmark.

Browsing

On a browser page, new links appear underlined in blue and previously visited links in purple. Images that act as links have a blue border around them.

104


Keys and commands used in browsing

• To open a link, press .

• To scroll the view, use the scroll key.

• To enter letters and numbers in a field, press the keys - . Press to enter special characters such as /, ., :, and @. Press to clear characters.

• To go to the previous page while browsing, press

Back

. If

Back

is not available, select

Options

→


→

History

to view a chronological list of the pages you have visited during a browsing session. The history list is cleared each time a session is closed.

• To check boxes and make selections, press .

• To retrieve the latest content from the server, select

Options

→


→

Reload

.

• To open a sublist of commands or actions for the currently open browser page, select

Options

→

Service options

.

• Press and hold to disconnect from a browser service and to quit browsing.

Saving bookmarks

• To save a bookmark while browsing, select

Options

→

Save as bookmark

.

• To save a bookmark received in a smart message, open the message in the Inbox in

Messaging and select

Options

→

Save to bookmarks

. See “Receiving smart messages” on page 52.

Viewing saved pages

If you regularly browse pages containing information which doesn’t change very often, you can save and then browse them when offline.

• To save a page, while browsing select

Options

→

Advanced options

→

Save page

.

Saved pages are indicated by the following icon:

- The saved browser page.

In the saved pages view you can also create folders to store your saved browser pages.


Options when browsing:

Open

,

Service options

,

Bookmarks

,

Save as bookmark

,

View image

,


,

Advanced options

,

Send bookmark

,

Find

,

Details

,

Settings

,

Help

, and

Exit

.

Options in the

Saved pages view:

Open

,

Back to page

,

Reload

,

Saved pages mngr.

,

Mark/Unmark

,


,

Advanced options

,

Details

,

Settings

,

Help

, and

Exit

.


105

Fig. 17 The Saved pages view.

Folders are indicated by the following icon:

- Folder containing saved browser pages.

• To open the Saved pages view, press in the Bookmarks view. In the Saved pages view, press to open a saved page.

To start a connection to the browser service and to retrieve the page again, select

Options

→


→

Reload

.

The phone stays online after you reload the page.

Downloading

You can download items such as ringing tones, images, operator logos, software, and video clips through the mobile browser. These items can be provided free or you can purchase them.

Once downloaded, items are handled by the respective applications on your phone, for example, a downloaded photo will be saved in the Gallery.

Important: Only install applications from sources that offer adequate protection against harmful software.

A cache is a memory location that is used to store data temporarily. If you have tried to access or have accessed confidential information requiring passwords, empty the cache after each use. The information or services you have accessed is stored in the cache. To empty the cache, select

Options

→


→

Clear cache

.

Purchasing an item

To download the item:

1 Scroll to the link and select

Options

→

Open

.

2 Choose the appropriate option to purchase the item, for example, Buy.

Carefully read all the information provided.

106


If the online content is compatible, you can use your wallet information to make the purchase:

1 Select

Open wallet

. You will be prompted for your wallet code. See “Entering the wallet code” on page 87.

2 Select the appropriate card category from your wallet.

3 Select

Fill in

. This will upload the selected wallet information.

If the wallet does not contain all information necessary for the purchase, you will be requested to enter the remaining details manually.


Checking an item before downloading

You can see details about an item before you download it. Details about an item may include the price, a brief description and size.


• Scroll to the link and select

Options

→

Open

.

Details about the item are displayed on your phone.

• If you want to continue with the downloading, press

Accept

, or if you want to cancel the download, press

Cancel

.

Ending a connection

• Select

Options

→

Advanced options

→

Disconnect

, or

• Press and hold to quit browsing and to return to standby mode.

Browser settings

Select

Options

→

Settings

:

Fig. 18 Example of details in a content file.


107

•

Default access point

- If you want to change the default access point, press to open a list of available access points. The current default access point is highlighted.

See

“Connection settings” on page 68.

•

Show images

- Choose if you want to view pictures when you are browsing. If you choose

No

, you can later load images during browsing by selecting

Options

→

Show images

.

•

Font size

- You can choose five text sizes in the browser:

Smallest

,

Small

,

Normal

,

Large

, and

Largest

.

•

Default encoding

- To make sure your browser pages display text characters correctly, select the appropriate language type.

•

Automatic bookmarks

- To turn the automatic completion of addresses in

Bookmarks On

or

Off

. To hide the

Auto. bookmarks

folder in

Bookmarks

, select

Hide folder

.

•

Screen size

- To use the whole display area for viewing Web pages, select

Full screen

.

•

Rendering

- Select

By quality

to have good image quality while browsing but at a slower page download speed, or

By speed

to download pages faster but have lower image quality.

•

Cookies

-

Allow

/

Reject

. You can enable or disable the receiving and sending of cookies

(a means of content providers to identify users and their preferences for frequently used content).

•

Security warnings

- Choose to hide or show security notifications.

•

Conf. DTMF sending

-

Always

/

First time only

. Choose whether you want to confirm before the phone sends DTMF tones during a voice call.

See “Options during a call” on page 17.

For example, you can make a voice call while you are viewing a browser page, send

DTMF tones while a voice call is in progress, and save in Contacts a name and phone number from a browser page.

•

Wallet

- Choose

On

if you want the wallet to open automatically when a compatible browser page is opened.

108


Application manager

In Application manager you can install new compatible Symbian operating system applications (SIS files) and Java™ applications (Java MIDlets and MIDlet suites). You can also update and uninstall applications from the phone, and monitor the installation history.


Applications in Application manager use shared memory.


When you open Application manager, you can see a list of:

• Applications saved in Application manager.

• Partially installed applications (indicated by ).

• Fully installed applications that you can remove (indicated by ).

You can only use Symbian operating system applications with a .SIS extension.

Your phone supports J2ME™Java applications. Do not download PersonalJava™ applications to your phone as they cannot be installed.

Go to

Menu

→

Tools

→ App. manager

Options in the

Application manager main view:

Install

,

View details

,

View certificate

,

Update

,

Go to web address

,

Remove

,

View log

,

Send log

,

Settings

,

App. downloads

,

Help

, and

Exit

.

Installing applications - general information

You can install applications that are specifically intended for this phone and suitable for the Symbian operating system.

If you install an application that is not intended specifically for this phone, it may function and look different from what was originally intended.

Applications may be downloaded to your phone during browsing, received as attachments in multimedia messages or e-mails, or received via Bluetooth from another device, for example, a phone or a compatible PC.

Important: Only install applications from sources that offer adequate protection against harmful software.


109

Fig. 19 The Application manager main view.

To increase protection, the application installation system uses digital signatures and certificates for applications. Do not install the application if Application manager gives a security warning during installation.

If you install an application that contains an update or repair to an existing application, you can only restore the original application if you have the original application or a full backup copy of the removed application. To restore the original application, first remove the updated or repaired application and then install again from the original application or the backup copy.

During installation, the phone checks the integrity of the application to be installed. The phone shows information about the checks being carried out and you are given options whether to continue or cancel the installation. Once the phone has checked the integrity of the application, it is installed on your phone.

Installing applications

• Open Application manager, scroll to the application, and select

Options

→

Install

to start the installation.

• Alternatively, search the phone memory or the memory card, select the application, and press to start the installation.

Some applications may give the option of partial installation allowing you to select the particular components of an application that you want to install. If you are installing an application without a digital signature or a certificate, the phone warns you of the risks.

Continue installation only if you are absolutely sure of the origin and contents of the application

Installing Java™

The .JAR file is required for installation. If it is missing, the phone may ask you to download it. If there is no access point defined for Application manager, you will be asked to select one. When you are downloading the .JAR file, you may need to enter a user name and

110


password to access the server. You obtain these from the supplier or manufacturer of the application.

• To start a data connection and to view extra information about the application, scroll to it and select

Options

→

Go to web address

.

• To start a data connection and to check if there is an update available for the application, scroll to it and select

Options

→

Update

.

Java settings

• To change the default access point that a Java application uses for downloading extra data, select

Options

→

Settings

→

Access point

.


• To change the security settings that determine the actions that a Java application is permitted to do, select

Options

→

Settings

.

Not all Java applications permit you to change the security settings.

Removing an application

1 To remove an application, scroll to it and select

Options

→

Remove

.

2 Press

Yes

to confirm the removal.

If you remove an application, you can only re-install it if you have the original application or a full backup of the removed application. If you remove an application, you may no longer be able to open documents created with that application. If another application depends on the application that you removed, the other application may stop working.

Refer to the documentation of the installed application for details.


111

Go to

Menu

→

Connectivity

→

Bluetooth

Connectivity

Bluetooth connection

This device is compliant with Bluetooth Specification 1.1 supporting the following profiles:

Dial-up networking profile (DUN) as a gateway, object push profile (OPP) as a client and server, File transfer profile (FTP) as a server, Hands-free profile (HFP) as an audio gateway,

Generic object exchange profile (GOEP), Generic access profile (GAP), and serial port profile

(SPP) with the PC connectivity software. To ensure interoperability between other devices supporting Bluetooth technology, use Nokia approved enhancements for this model. Check with the manufacturers of other devices to determine their compatibility with this device.

There may be restrictions on using Bluetooth technology in some locations. Check with your local authorities or service provider.

Features using Bluetooth technology, or allowing such features to run in the background while using other features, increase the demand on battery power and reduces the battery life.

Bluetooth technology enables wireless connections between electronic devices within a maximum range of 10 metres. A Bluetooth connection can be used to send images, videos, texts, business cards, calendar notes, or to connect wirelessly to compatible devices using

Bluetooth technology, such as computers.

Since devices using Bluetooth technology communicate using radio waves, your phone and the other devices do not need to be in direct line-of-sight. The two devices only need to be within a maximum of 10 metres of each other, although the connection can be subject to interference from obstructions such as walls or from other electronic devices.

112


When you activate Bluetooth for the first time, you are asked to give a name to your phone.

Bluetooth settings

•

Bluetooth

-

On

/

Off

.

•

My phone's visibility

-

Shown to all

- Your phone can be found by other Bluetooth devices or

Hidden

- Your phone cannot be found by other devices.

•

My phone’s name

- Define a name for your phone.

After you have set Bluetooth as active and changed

My phone's visibility

to

All

, your phone and this name can be seen by other Bluetooth device users.

Sending data via Bluetooth

There can be only one active Bluetooth connection at a time.

1 Open an application where the item you wish to send is stored. For example, to send a photo to another device, open the Gallery application.

2 Scroll to the item you want to send and select

Options

→

Send

→

Via Bluetooth

.

3 The phone starts to search for devices within range. Devices using Bluetooth technology that are within range start to appear on the display one by one. You can see a device icon, the device’s name, the device type, or a short name. Paired devices are shown with

. A paired device is one where a Bluetooth connection already exists between your phone and the other device.

• To interrupt the search, press

Stop

. The device list freezes and you can start to form a connection to one of the devices already found.

When searching for devices, some devices may show only the unique device addresses.

To find out the unique address of your phone, enter the code *#2820# in standby mode.

If you have searched for devices earlier, a list of the devices that were found previously is shown first. To start a new search, select

More devices

. If you switch off the phone, the list of devices is cleared and the device search needs to be started again before sending data.

Fig. 20 Using Bluetooth.


113

Fig. 21 Sending an image via Bluetooth, the phone starts to search for devices.

4 Scroll to the device you want to connect with and press

Select

. The item you are sending is copied to Outbox and the note

Connecting

is shown.

5 Pairing (if not required by the other device, go to step 6.)

• If the other device requires pairing before data can be transmitted, a tone sounds and you are asked to enter a passcode.

• Create your own passcode (1-16 characters long, numeric) and agree with the owner of the other device to use the same code. This passcode is used only once and you do not have to memorise it.

• After pairing, the device is saved to the Paired devices view.

6 When the connection has been successfully established, the note

Sending data

is shown.


Data received via Bluetooth can be found in the Inbox folder in Messaging.

See “Inbox - receiving messages” on page 52.

Tip: Pairing means authentication. The users of the devices using Bluetooth technology should agree together what the passcode is, and use the same passcode for both devices in order to pair them. Devices that do not have a user interface have a preset passcode.

Icons for different devices:

-

Computer

,

Audio/video

, and -

Bluetooth device

.

If sending fails, the message or data will be deleted. The Drafts folder in Messaging does not store messages sent via Bluetooth.

Checking the status of the Bluetooth connection

• When is shown in standby mode, Bluetooth is active.

• When is blinking, your phone is trying to connect to the other device.

• When is shown continuously, the Bluetooth connection is active.

114


Paired devices view

Paired devices are easier to recognise, they are indicated by in the search result list. In the Bluetooth main view, press to open a list of paired devices ( ).

• To pair with a device: Select

Options

→

New paired device

. The phone starts a device search. Scroll to the device you want to pair with and press

Select

. Exchange passcodes.

The device is added to the Paired devices list.

• To cancel pairing: Scroll to the device whose pairing you want to cancel and press or select

Options

→

Delete

. If you want to cancel all pairings, select

Options

→

Delete all

.

If you are currently connected to a device, and delete the pairing with that device, the pairing is removed and the device connection is terminated, but Bluetooth remains active on the handset.

• To set a device to be authorised or unauthorised: Scroll to the device and select

Options

→

Set as authorised

- Connections between your phone and this device can be made without your knowledge. No separate acceptance or authorisation is needed. Use this status for your own devices, for example, your PC, or devices that belong to someone you trust. The icon is added next to authorised devices in the Paired devices view.

Set as unauthorised

- Connection requests from this device need to be accepted separately every time.

• To assign a short name to a device: Select

Options

→

Assign short name

. Enter a name for the device.

Receiving data via Bluetooth

When you receive data via Bluetooth, a tone sound is played and you are asked if you want to accept the message. If you accept, the item is placed in the Inbox folder in Messaging.

Messages received via Bluetooth are indicated by .

See “Inbox - receiving messages” on page 52.


115

Go to

Menu

→

Connectivity

→

Connection manager

Disconnecting Bluetooth

A Bluetooth connection is disconnected automatically after sending or receiving data.

Connection manager

In Connection manager you can identify the status of multiple data connections, view details on the amount of data sent and received, and end unused connections.

See

Fig. 22 on page 116.

You can view details of data connections only. Voice calls are not listed.

When you open Connection manager, you can see a list of:

• Open data connections, -

Data call GPRS

• The status of each connection.

• Amount of data uploaded and downloaded for each connection (GPRS connections only).

• The duration of each connection (Data call connections only).

Note: The actual time invoiced for calls by your service provider may vary, depending on network features, rounding off for billing, and so forth.

116

Fig. 22 The Connection manager main view.

Options in the

Connection manager main view when there are one or more connections:

Details

,

Disconnect

,

Disconnect all

,

Help

and

Exit

.

Viewing connection details

To view the details of a connection, scroll to a connection and select

Options

→

Details

The following is displayed:

•

Name

- The name of the Internet Access Point (IAP) in use.

•

Bearer

- The type of data connection:

Data call

or

GPRS

.

•

Status

- The current status of the connection.


•

Received

- The amount of data, in bytes, received to the phone.

•

Sent

- The amount of data, in bytes, sent from the phone.

•

Duration

- The length of time that the connection has been open.

•

Speed

- The current speed of both sending and receiving data in kB/s (kilobytes per second).

•

Dial-up

(GSM) - The dial-up number used, or

Name

(GPRS) - access point name used.

•

Shared

(not displayed if the connection is not shared) - The number of applications using the same connection.

Ending connections

• Scroll to a connection and select

Options

→

Disconnect

to end that connection only.

• Select

Options

→

Disconnect all

to close all currently open connections.

Connecting your phone to a compatible computer

For further information on how to make a connection to a compatible computer via USB or Bluetooth, and how to install Nokia PC Suite 6.3, see the User’s Guide for Nokia PC Suite on the CD-ROM. For further information on how to use Nokia PC Suite, see the help function on PC Suite or visit the support pages at www.nokia.com.

Sync - remote synchronisation

The Sync application enables you to synchronise your calendar or contacts with various calendar and address book applications on a compatible computer or on the Internet.

Synchronisation takes place over a GSM data call or packet data connection.

Go to

Menu

→

Connectivity

→

Sync


117

Options in the

Remote sync main view:

Synchronise

,

New sync profile

,

Edit sync profile

,

Delete

,

View log

,

Help

, and

Exit

.

The synchronisation application uses SyncML technology for synchronisation. For information on SyncML compatibility, please contact the supplier of the calendar or address book application you want to synchronise your phone data with.

Creating a new synchronisation profile

1 If no profiles have been defined, the phone asks you if you want to create a new profile.

Select

Yes

.

To create a new profile in addition to existing ones, select

Options

→

New sync profile

.

Choose whether you want to use the default setting values or copy the values from an existing profile to be used as the basis for the new profile.

2 Define the following:

Sync profile name

- Write a descriptive name for the profile.

Access point

- Select an access point you want to use for the data connection.

Host address

- Contact your service provider or system administrator for the correct values.

Port

- Contact your service provider or system administrator for the correct values.

User name

- Your user ID for the synchronisation server. Contact your service provider or system administrator for your correct ID.

Password

- Write your password. Contact your service provider or system administrator for the correct value.

Press to select:

Calendar

- Select

Yes

if you want to synchronise your calendar.

Remote calendar

- Enter a correct path to the remote calendar on the server. Must be defined if the previous setting

Calendar

has been set to

Yes

.

Contacts

- Select

Yes

if you want to synchronise your contacts.

Remote contacts

- Enter a correct path to the remote address book on the server. It must be defined if the previous setting

Contacts

has been set to

Yes

.

3 Press

Done

to save the settings.

118


Synchronising data

In the Sync main view, you can see the different profiles, and what kind of data will be synchronised: Calendar, Contacts, or both.

1 In the main view, scroll to a profile and select

Options

→

Synchronise

. The status of the synchronisation is shown at the bottom of the screen.

To cancel synchronisation before it is finished, press

Cancel

.

2 You are notified when the synchronisation has been completed.

• After synchronisation is complete, press

View log

or select

Options

→

View log

to open a log file showing the synchronisation status (

Complete

or

Incomplete

) and how many calendar or contact entries have been added, updated, deleted, or discarded (not synchronised) in the phone or on the server.


119

Troubleshooting

Memory low

When the following notes are shown, the phone memory is low and you must start to delete some data:

Not enough memory to perform operation. Delete some data first.

or

Memory low. Delete some data.

To view what kind of data you have and how much memory the different data groups consume, go to

File manager

and select

Options

→

Memory details

.

You may want to delete the following items regularly to avoid memory getting low:

• Messages from the Inbox, Drafts, and Sent folders in

Messaging.

• Retrieved e-mail messages from the phone memory.

• Saved browser pages.

• Images and photos in Images.

If you want to delete contact information, calendar notes, call timers, call cost timers, game scores, or any other data, go to the respective application to remove the data.

If you are deleting multiple items and another of the following notes are shown:

Not enough memory to perform operation. Delete some data first.

or

Memory low. Delete some data.,

try deleting items one by one (starting from the smallest item).

Clearing calendar memory - To remove more than one event at a time, go to the Month view and select

Options

→

Delete entry

→ and either:

•

Before date

- to delete all calendar notes which take place before a certain date. Enter the date before which all calendar notes will be deleted.

•

All entries

- to delete all calendar notes.

Erasing log information - To erase all the log contents,

Recent calls register, and Messaging delivery reports permanently, go to Logs and select

Options

→ to

Settings

→

Log duration

→

No log

.

Clear log

or go

Different ways to store data:

• Use Nokia PC Suite 6.3 to make a backup copy of all data to a compatible computer.

• Send images to your e-mail address and then save the images to your computer.

• Send data via Bluetooth to a compatible device.

• Store data on a compatible memory card.

120


Q&A

Phone display

• Q. Why do missing, discoloured or bright dots appear on the screen every time I turn on my phone?

A. This is a characteristic of this type of display. Some displays may contain pixels or dots that remain on or off.

This is normal, not a fault.

Camera

• Q: Why do images look smudgy?

A: Check that the camera lens protection window is clean.

Bluetooth

• Q: Why can’t I end a Bluetooth connection?

A: If another device is connected to your phone, you can either end the connection using the other device or by deactivating Bluetooth. Go to Bluetooth and select the setting

Bluetooth

→

Off

.

• Q: Why can’t I find my friend’s Bluetooth-enabled device.

A: Check that both have activated Bluetooth.

Check that the distance between the two devices is not over 10 metres or that there are no walls or other obstructions between the devices.

Check that the other device is not in ‘Hidden’ mode.

Check that both devices are compatible.

Multimedia messaging

• Q: What should I do when the phone tells me that it cannot receive a multimedia message because memory is full?

A: The amount of memory needed is indicated in the error message:

Not enough memory to retrieve message. Delete some data first.

To view what kind of data you have and how much memory the different data groups consume, go to

File manager

and select

Options

→

Memory details

.

• Q: How can I end the data connection when the phone starts a data connection again and again? The notes:

Retrieving message

or

Trying to retrieve message again

are shown briefly. What is happening?

A: The phone is trying to retrieve a multimedia message from the multimedia messaging centre.

Check that the settings for multimedia messaging have been defined correctly and that there are no mistakes in phone numbers or addresses. Go to

Messaging

and select

Options

→

Settings

→


.

To stop the phone from making a data connection, you have the following options. Go to

Messaging

and select

Options

→

Settings

→


, and then:

• Select

On receiving msg.

→

Defer retrieval

if you want the multimedia messaging centre to save the message to be retrieved later, for example, after you have checked the settings. After this change, the phone still needs to send information notes to the network. To retrieve the message later, select

Retr. immediately

.

• Select

On receiving msg.

→

Reject message

- if you want to reject all incoming multimedia messages. After this change, the phone needs to send information notes to the network and the multimedia messaging centre will


121

delete all multimedia messages that are waiting to be sent to you.

• Select

Multimedia reception

→

Off

- if you want to ignore all incoming multimedia messages. After this change the phone will not make any network connections related to multimedia messaging.

Messaging

• Q: Why can’t I select a contact?

A: If you cannot select a contact in the Contacts directory, the contact card does not have a phone number or an email address. Add the missing information to the contact card in the Contacts application.

Calendar

• Q: Why are the week numbers missing?

A: If you have changed the Calendar settings so that the week starts on a day other than Monday, then the week numbers will not be shown.

Browser Services

• Q:

No valid access point defined. Define one in Services settings.

A: Insert proper browser settings. Contact your service provider for instructions.

Log

• Q: Why does the log appear empty?

A: You may have activated a filter, and no communication events fitting that filter have been logged. To see all events, select

Options

→

Filter

→

All communication

.

PC connectivity

• Q: Why do I have problems in connecting the phone to my

PC?

A: Make sure that Nokia PC Suite 6.3 is installed and running on your PC. See the User’s Guide for Nokia PC

Suite on the CD-ROM. For further information on how to use Nokia PC Suite, see the help function on PC Suite or visit the support pages at www.nokia.com

.

Access codes

• Q: What is my password for the lock, PIN, or PUK codes?

A: The default lock code is 12345. If you forget or lose the lock code, contact your phone dealer.

If you forget or lose a PIN or PUK code, or if you have not received such a code, contact your network service provider.

For information about passwords, contact your access point provider, for example, a commercial Internet Service

Provider (ISP), service provider, or network operator.

Application not responding

• Q: How do I close an application that is not responding?

A: Open the application switching window by pressing and holding . Then scroll to the application, and press to close the application.

122


Battery information

Charging and Discharging

Your device is powered by a rechargeable battery. The full performance of a new battery is achieved only after two or three complete charge and discharge cycles. The battery can be charged and discharged hundreds of times but it will eventually wear out. When the talk and standby times are noticeably shorter than normal, buy a new battery. Use only

Nokia approved batteries, and recharge your battery only with

Nokia approved chargers designated for this device.

Unplug the charger from the electrical plug and the device when not in use. Do not leave the battery connected to a charger. Overcharging may shorten its lifetime. If left unused, a fully charged battery will lose its charge over time.

Temperature extremes can affect the ability of your battery to charge.

Use the battery only for its intended purpose. Never use any charger or battery that is damaged.

Do not short-circuit the battery. Accidental short-circuiting can occur when a metallic object such as a coin, clip, or pen causes direct connection of the positive (+) and negative (-) terminals of the battery. (These look like metal strips on the battery.) This might happen, for example, when you carry a spare battery in your pocket or purse. Short-circuiting the terminals may damage the battery or the connecting object.

Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions, will reduce the capacity and lifetime of the battery. Always try to keep the battery between 15°C and 25°C (59°F and 77°F). A device with a hot or cold battery may not work temporarily, even when the battery is fully charged. Battery performance is particularly limited in temperatures well below freezing.

Do not dispose of batteries in a fire! Dispose of batteries according to local regulations. Please recycle when possible.

Do not dispose as household waste.


123

Care and Maintenance

Your device is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help you protect your warranty coverage.

• Keep the device dry. Precipitation, humidity and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet, remove the battery and allow the device to dry completely before replacing it.

• Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged.

• Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics.

• Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards.

• Do not attempt to open the device other than as instructed in this guide.

• Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics.

• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.

• Do not paint the device. Paint can clog the moving parts and prevent proper operation.

• Use a soft, clean, dry cloth to clean any lenses (such as camera, proximity sensor, and light sensor lenses).

• Use only the supplied or an approved replacement antenna. Unauthorised antennas, modifications, or attachments could damage the device and may violate regulations governing radio devices.

All of the above suggestions apply equally to your device, battery, charger, or any enhancement. If any device is not working properly, take it to the nearest authorized service facility for service.

124


Additional safety information

A few practical rules about accessories and enhancements

• Keep all accessories and enhancements out of the reach of small children.

• When you disconnect the power cord of any accessory or enhancement, grasp and pull the plug, not the cord.

• Check regularly that enhancements installed in a vehicle are mounted and are operating properly.

• Installation of any complex car enhancements must be made by qualified personnel only.

Operating environment

Remember to follow any special regulations in force in any area and always switch off your device when its use is prohibited or when it may cause interference or danger. Use the device only in its normal operating positions. To maintain compliance with radio frequency exposure guidelines only use enhancements approved by Nokia for use with this device.

When the device is on and being worn on the body, always use an approved holder or carrying case.

Parts of the device are magnetic. Metallic materials may be attracted to the device, and persons with a hearing aid should not hold the device to the ear with the hearing aid. Always secure the device in its holder, because metallic materials may be attracted by the earpiece. Do not place credit cards or other magnetic storage media near the device, because information stored on them may be erased.

Medical devices

Operation of any radio transmitting equipment, including wireless phones, may interfere with the functionality of inadequately protected medical devices. Consult a physician or the manufacturer of the medical device to determine if they are adequately shielded from external RF energy or if you have any questions. Switch off your device in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy.

Pacemakers

Pacemaker manufacturers recommend that a minimum separation of 6 in. (15.3 cm) be maintained between a wireless phone and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with the independent research by and recommendations of Wireless Technology Research. Persons with pacemakers should:

• always keep the device more than 6 in. (15.3 cm) from their pacemaker when the device is switched on;

• not carry the device in a breast pocket; and

• hold the device to the ear opposite the pacemaker to minimise the potential for interference.

If you have any reason to suspect that interference is taking place, switch off your device immediately.


125

Hearing aids

Some digital wireless devices may interfere with some hearing aids. If interference occurs, consult your service provider.

Vehicles

RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles such as electronic fuel injection systems, electronic antiskid (antilock) braking systems, electronic speed control systems, air bag systems. For more information, check with the manufacturer or its representative of your vehicle or any equipment that has been added.

Only qualified personnel should service the device, or install the device in a vehicle. Faulty installation or service may be dangerous and may invalidate any warranty that may apply to the device. Check regularly that all wireless device equipment in your vehicle is mounted and operating properly. Do not store or carry flammable liquids, gases, or explosive materials in the same compartment as the device, its parts, or enhancements. For vehicles equipped with an air bag, remember that air bags inflate with great force. Do not place objects, including installed or portable wireless equipment in the area over the air bag or in the air bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result.

Using your device while flying in aircraft is prohibited. Switch off your device before boarding an aircraft. The use of wireless teledevices in an aircraft may be dangerous to the operation of the aircraft, disrupt the wireless telephone network, and may be illegal.

Potentially explosive environments

Switch off your device when in any area with a potentially explosive atmosphere and obey all signs and instructions.

Potentially explosive atmospheres include areas where you would normally be advised to turn off your vehicle engine.

Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Switch off the device at refuelling points such as near gas pumps at service stations.

Observe restrictions on the use of radio equipment in fuel depots, storage, and distribution areas, chemical plants or where blasting operations are in progress. Areas with a potentially explosive atmosphere are often but not always clearly marked. They include below deck on boats, chemical transfer or storage facilities, vehicles using liquefied petroleum gas (such as propane or butane), and areas where the air contains chemicals or particles such as grain, dust or metal powders.

Emergency calls

Important: Wireless phones, including this device, operate using radio signals, wireless networks, landline networks, and user-programmed functions. Because of this, connections in all conditions cannot be guaranteed. You should never rely solely on any wireless device for essential communications like medical emergencies.

To make an emergency call:

1

If the device is not on, switch it on. Check for adequate signal strength.

Some networks may require that a valid SIM card is properly inserted in the device.

126


2

Press as many times as needed to clear the display and ready the device for calls.

3

Key in the official emergency number for your present location. Emergency numbers vary by location.

4

Press the key.

If certain features are in use, you may first need to turn those features off before you can make an emergency call. Consult this guide or your service provider for more information.

When making an emergency call, give all the necessary information as accurately as possible. Your wireless device may be the only means of communication at the scene of an accident. Do not end the call until given permission to do so.

Certification information (SAR)

THIS DEVICE MEETS INTERNATIONAL GUIDELINES FOR

EXPOSURE TO RADIO WAVES

Your mobile device is a radio transmitter and receiver. It is designed and manufactured not to exceed the limits for exposure to radio frequency (RF) recommended by international guidelines (ICNIRP). These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines were developed by independent scientific organisations through periodic and thorough evaluation of scientific studies. The guidelines include a substantial safety margin designed to assure the safety of all persons, regardless of age and health.

The exposure standard for mobile devices employs a unit of measurement known as the Specific Absorption Rate, or SAR.

The SAR limit stated in the international guidelines is 2.0 W/ kg*. Tests for SAR are conducted using standard operating positions with the device transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual

SAR of the device while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a base station, the lower the power output of the device.

The highest SAR value for this device when tested for use at the ear is 0.67 W/kg.

This device meets RF exposure guidelines when used either in the normal use position against the ear or when positioned at least 2.2 cm away from the body. When a carry case, belt clip or holder is used for body-worn operation, it should not contain metal and should position the product at least 2.2 cm away from your body.

In order to transmit data files or messages, this device requires a quality connection to the network. In some cases, transmission of data files or messages may be delayed until such a connection is available. Ensure the above separation distance instructions are followed until the transmission is completed.

* The SAR limit for mobile devices used by the public is 2.0 watts/kilogram (W/kg) averaged over ten grams of body tissue. The guidelines incorporate a substantial margin of safety to give additional protection for the public and to account for any variations in measurements. SAR values may vary depending on national reporting requirements and the network band. For SAR information in other regions please look under product information at www.nokia.com.


127

128

Index

A

Access points

Settings

68

Alarm clock

Snooze

93

Animations

37

Applications

Installing

110

Removing files

111

Automatic answer

73

B

Background images

43

Bluetooth

112

Closing the connection

116

Connection requests

114

Connection status indicators

114

Device icons

114

Pairing

114

Pairing requests

114

Passcode, glossary explanation

114

Preset passcode

114

Receiving data

115

Sending data

113

Unique device address

113

Browser

Connecting

103


Ending connections

107

Icons

104

Service messages

53

,

54

WAP pages

102

XHTML pages

102

Browsing

104

C

Call register

See Log

Calls

Answering

17

Conference calls

16

Dialled

20

Diverting

17

Duration

20

International

15

Missed

20

Options during a call

17

Received

20

Rejecting

17

Settings

67

Transferring

18

Cell broadcast messages

57

Cell info display

73

Certificates

Trust settings

77

Chat

Sending messages

97

Clearing memory

Log information

120

Closed chat group

100

Computer connections

117

Conference calls

16

Connecting to a PC

117

Connection

Viewing

116

Connection indicators

Bluetooth

114

Contact cards

Removing ringing tones

23

Contact groups

26

Contacts

Data Import

33

Copying

Contacts between the SIM card and phone memory

23

Text

49

Creating

Contact cards

22

D

Data connections to network

Ending

117

Viewing

116

Data Import

Contacts

33

Dialled numbers

20

Digital rights management

106

Diverting calls

17

E

E-mail

Deleting

55

Retrieving from mailbox

54

Erasing

Recent calls register

20

F

Favourites

Adding a shortcut

101

File formats

RealPlayer

38

SIS file

109

File manager

78

Folders

Creating

12

Organising

12

G

Gallery

Picture messages

43

Uploading images

43

GIF animations

37

GPRS

See Packet data

GPRS connections

116

GSM data connections

116

I

Image server

43

Importing data from other Nokia phones

33

Indicators

10

Info service

57

Installing applications

110

Installing Java files

110

J

Java

Installing Java applications

110

See Applications.

L

Language for writing

66

Listening to messages

16

M

Media files

File formats

38

Mute

39

Seek

39

Media gallery

41

Background images

43

Memory

Viewing memory details

78

Memory low

Viewing memory consumption

83

Menu

11

Menu key

11

Missed calls

20

Mobile browser

102

Music files

See Media files

Mute

39

N

Nickname in chat

95

P

Packet data

Connection timer

21

Data counter

21

Settings

71

Pairing, glossary explanation

114

Password

Memory card

82

PC Suite

117

Personalisation

85

Personalise

85

Alarm

94

Phonebook

See Contacts

Picture messages

42

,

43

Pictures

42

,

43

PIN code

Unblocking

74

Predictive text input

Tips

48

Turning off

49


129

130

Profiles

84

Adding voice commands

80

Renaming

85

R

Received calls

20

Receiving

Data via Bluetooth

115

Ringing tones, Operator logos, and settings, see Smart messages

Recent calls register

Call duration

20

Dialled numbers

20

Erasing call lists

20

Missed calls

20

Received calls

20

Recorder, recording sounds

94

Recording video

36

Rejecting calls

17

Remote synchronisation

117

Removing an application

111

Removing software

111

Ringing tones

Muting

17

Receiving in a smart message

53

S

Screen saver

Settings

67

Seek

39

Sending

Data via Bluetooth

113


Service command editor

58

Shared memory

14

Shortcuts in Favourites

101

SIM card

Copying names and numbers

23

SIS file

109

Smart messages

Receiving

52

Snooze

93

Software

Removing

111

Transferring a .SIS file to your phone

109

Sound clips

42

Sound files

See Media files

Sounds

Removing a personal ringing tone

23

Standby mode

Indicators

10

Settings

67

Stopping

Alarm clock

93

Switching between applications

12

Synchronisation

See Remote synchronisation.

T

Transferring calls

18

U

Uploading images

43

USSD commands

58

V

Video clips

42

See Media files

Video player

See Real Player

Video recorder

Memory card

37

Saving video clips

36

Settings

36

Viewing

Connection details

116

GIF animations

37

Network data connection details

116

Voice commands

79

Voice mailbox

16

Changing the number

16

Voice messages

16

Voice recorder

94

Voice tags

Making calls

25

Volume control

13

W

WAP pages

Browser

102

Writing

Predictive text input, turning off

49

X

XHTML pages

Browser

102


131

Nokia 6670 mobile phone User guide

Assistant Bot

Contents

For your safety

About your device

Network Services

Chargers and enhancements

General information

Essential indicators in standby mode

Menu

Switching between applications

Actions common to all applications

Volume control

Shared memory

Your phone

Making a call

Making a call using the Contacts directory

Calling your voice mailbox (Network Service)

Changing the voice mailbox number

Speed dialling a phone number

Making a conference call (Network Service)

Answering a call

Options during a call

Call waiting (Network Service)

Diverting calls (Network Service)

Log - Call register and general log

GPRS data counter

Recent calls register

Call duration

Viewing the general log

Personal information

Contacts

Creating and editing contact cards

Copying contacts between the SIM card and phone memory

Adding a ringing tone for a contact card or group

Voice dialling

Adding a voice tag to a phone number

Making a call by saying a voice tag

Assigning speed dialling keys

Viewing subscribed contacts

Managing contact groups

Creating contact groups

Adding members to a group

Presence (Network Service)

Changing your availability information

Changing who can view your Presence information

Public viewers

Private viewers

Blocked viewers

Updating your Presence information

Presence settings

Positioning (Network Service)

Calendar

Creating calendar entries

Calendar views

To-do

Importing data from compatible Nokia phones

Multimedia

Camera

Taking pictures

Self-timer

Settings

Recording videos

Setting up your Video recorder

Viewing images

Zooming on a saved image

Keyboard shortcuts

RealPlayer™

Playing media files

Shortcuts during play

Changing the settings

Movie director

Gallery

Opening files

Other default folders

Picture messages folder

Wallpapers folder

Presence logos folder

Downloading files

Uploading images to an image server (Network Service)