Directed DBALL2 CHRYSLER door lock and override module Installation guide
Below you will find brief information for door lock and override module DBALL2 CHRYSLER. This document details installation and programming instructions for the DBALL2 CHRYSLER door lock and override module, a comprehensive device compatible with a wide range of Chrysler, Dodge, Jeep, and Volkswagen vehicles.
advertisement
Platform: DBALL2
Firmware: CHRYSLER
Rev.: 20160907
Update Alert: Firmware updates are posted to the web on a regular basis. We recommend
that you check for firmware and/or install guide updates prior to installing this product.
Installation Guide
The CHRYSLER firmware for DBALL2 is an all-in-one door lock and override module compatible with specific Chrysler, Dodge, Jeep and Volkswagen vehicles.
This module can only be flashed and configured using DirectLink at www.directechs.com or using the Directechs Mobile application for smartphones. Refer to the Module Programming section on pages 21-22 for more information.
Index
Vehicle Application Guide................................................................................................................................................
02
Installation
Type 1a (with CHTHD1/THCHD1 T-Harness R7)..........................................................................................................
Type 1b (with CHTHD1/THCHD1 T-Harness R1-R6)....................................................................................................
Type 1c (without T-Harness)..........................................................................................................................................
Vehicle wiring reference chart (Type 1)...........................................................................................................................
Type 2a (with CHTHD1/THCHD1 T-Harness R7)..........................................................................................................
Type 2b (with CHTHD1/THCHD1 T-Harness R1-R6)....................................................................................................
Type 2c (without T-Harness)..........................................................................................................................................
Vehicle wiring reference chart (Type 2)...........................................................................................................................
Type 3a (with CHTHD2/THCHD2 T-Harness R9)..........................................................................................................
Type 3b (with CHTHD2/THCHD2 T-Harness R1-R6)....................................................................................................
Type 3c (without T-Harness)..........................................................................................................................................
Vehicle wiring reference chart (Type 3)...........................................................................................................................
Type 4..............................................................................................................................................................................
Vehicle wiring reference chart (Type 4)...........................................................................................................................
Type 5..............................................................................................................................................................................
Vehicle wiring reference chart (Type 5)...........................................................................................................................
14
15
17
18
19
20
10
11
12
13
03
04
05
06
08
09
Programming
Module Programming - Vehicles WITH Factory Keyless................................................................................................
Module Programming - Vehicles WITHOUT Factory Keyless........................................................................................
Module Reset..................................................................................................................................................................
Hard Reset.......................................................................................................................................................................
Feature & Option List.......................................................................................................................................................
Feature Programming......................................................................................................................................................
21
22
23
23
24
25
LED Diagnostics & Troubleshooting................................................................................................................................
26
Limited One-Year Consumer Warranty............................................................................................................................
27
Quick Reference Guide...................................................................................................................................................
28
® Chrysler, Dodge, Jeep and Volkswagen are registered trademarks and property of their respective companies.
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Rev.: 20160907
Page 2
Vehicle Application Guide
The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle.
Ve hicle s
Chrysle r
200
300/300c
300/300c
Aspen
PT Cruiser
Sebring
Sebring Convertible
Sebring Sedan
Town & Country
Dodge /Ra m
1500
2500
3500
Avenger
C/V
Caliber
Caravan
Challenger
Challenger (Smart Key)
Charger
Charger
Dakota
Dakota
Durango
Durango
Durango
Grand Caravan
Journey
Magnum
Magnum
Nitro
RAM
RAM
Je e p
Commander
Compass
Grand Cherokee
Grand Cherokee
Grand Cherokee
Grand Cherokee (Smart Key)
Liberty
Patriot
W rangler
Mitsubishi
Raider
Raider
Volksw a ge n
Routan
1 1 1 1 1
3
3
4
3
1 1
3
3
3
4
3
1
1 1
1
3 3 3
1
1
1 1 1
3
1
1
1
3 3
1 1 1
1 1 1
3 3
1
1 1
1 1
2
3
1
1
3
1
2
1 1 1 1 1 1 1
1
1
1
3 3 3 3 3
1 1
2
3 3
1
2
2
3
2
3 3
3 3
1 1
3
3 3 3
3 3 3
1
3 3
3 3
3 3
3
3
3
Legend:
•: D2D & Wire-to-Wire (W2W)
W: Wire-to-Wire
AV: Horn & Lights Controls
PK: Transponder & Immobilizer Override
CC: Comfort & Convenience Control
3 3 3 3
2 2
3 3 3
1 1 1
3
3 3
1
3
1
3
1 1 1 1 1
2
3
3
3
4
3
1
3
3
3
1
2
3
3 or 4*
2
3
3
3
1
1
3
1
2
2
3
3
4
3
4
3
4
3
3
3 or 4*
3
3
4
3
4
3
3
4
4
4
5
5
4
3 or 4* 3 or 4*
4
3
4
4
5
RS: Remote Start & Engine Controls
DL: OE Door Lock & Alarm Controls
SS: Integrated Security & Monitoring
ST: Function/Feature Status
4
5
5
4
4
5
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
• •
•
•
•
•
•
•
•
•
• W
W
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
W
W
W
W
W
W
W
W
W
W
W
W
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
W
W
•
•
•
•
•
•
•
•
•
•
•
•
• W
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
D
D
D
D
D
D
D
D
D
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
D
D
D
D
D
D
D
D
D
•
•
•
•
•
•
•
•
• D
D
D
D
D
D
D
D
D
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
D
•
D
D
D
D
D
D
D
D
D
•
•
•
•
•
•
•
•
•
• •
D
D
D
•
•
•
•
•
•
•
• •
D
D
D •
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
* To select the proper install type, locate the ignition switch connector and select your install type as illustrated below:
Pin 4 empty
(+) Starter wire in pin 4
Type 3 vehicles do not have a (+) Starter wire at the ignition switch
5 or 6
1
Connector side view at ignition switch
OR
Type 4 vehicles have a
(+) Starter wire at pin 4 of the ignition switch
5 or 6 1
Connector side view at ignition switch
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Installation Type 1a (with CHTHD1/THCHD1 T-Harness R7)
Refer to the Vehicle Wiring Reference Charts on pages 6-7 for wire color and location.
See page 6 for wiring information
Parking
Lights
OR
Connect for Dodge
Journey only.
This is the only connection required for parking light output for the Dodge Journey, and the
DBALL MUX connection is not required.
[2]
(+) Parking Light Output
[1]
(AC) Tach Input
Rev.: 20160907
Page 3
(-) Ground
(+) 12V
(-) Ground
(+) 12V
(-) Hood Switch
(+) Ignition Input/Output
(-) Hood Switch
D2D only
Pink
Remote Start Safety
Override Switch is inactive
(used for RSR only)
[1]
(AC) Tach Output: Violet/White: 5
(MUX) Parking Lights: Violet/Green: 8
(MUX) Parking Lights: Violet/Brown: 9
RAP Off: Yellow/Black: 10
(-) Driver door trigger
Violet wire in driver kick panel
RF
Prog. Button
LED
Do
NOT
connect
DBALL2
(+)12V
RX
(-) Ground
TX
P#: XKD2D65
CHTHD1/THCHD1 R7
(optional)
12-pin Connector
(harness side)
12-pin Connector
(harness side)
12-pin Connector
(Vehicle side)
Ignition
Barrel
(vehicle side)
[1]
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2]
Connection only required for Dodge Journey.
Wires not listed in this diagram are not required for the installation.
All adapters are displayed from the wire side (unless specified otherwise).
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Installation Type 1b (with CHTHD1/THCHD1 T-Harness R1-R6)
Refer to the Vehicle Wiring Reference Charts on pages 6-7 for wire color and location.
See page 6 for wiring information
(-) Ground
Parking
Lights
OR
Connect for Dodge
Journey only.
This is the only connection required for parking light output for the Dodge Journey, and the
DBALL MUX connection is not required.
[2]
(+) Parking Light Output
(+) 12V
(-) Hood Switch
[1]
(AC) Tach Input
(+) Ignition Input/Output
(-) Ground
(+) 12V
(-) Hood Switch
Rev.: 20160907
Page 4
D2D only
Remote Start Safety
Override Switch is inactive
(used for RSR only)
[1]
(AC) Tach Output: Violet/White: 5
(MUX) Parking Lights: Violet/Green: 8
(MUX) Parking Lights: Violet/Brown: 9
RAP Off: Yellow/Black: 10
(-) Driver door trigger
Violet wire in driver kick panel
RF
Prog. Button
LED
Do
NOT
connect
DBALL2
(+)12V
RX
(-) Ground
TX
P#: XKD2D65
CHTHD1/
THCHD1 R1-R6
(optional)
Connect to White/Red wire, pin 3
12-pin Connector
(harness side)
12-pin Connector
(harness side)
12-pin Connector
(Vehicle side)
Ignition
Barrel
(vehicle side)
[1]
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2]
Connection only required for Dodge Journey.
Wires not listed in this diagram are not required for the installation.
All adapters are displayed from the wire side (unless specified otherwise).
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Installation Type 1c (without T-Harness)
Refer to the Vehicle Wiring Reference Charts on pages 6-7 for wire color and location.
(+) Brake Input
[1]
(AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(-) E-Brake Status Input
(-) Ground
(+) 12V
(-) Hood Switch
(-) Lock Output
(-) Unlock Output
(-) Trunk Output
(-) Aux1 Right Sliding Door
(-) Aux2 Left Sliding Door
(+) Starter Output
(-) GWR (Status)
(+) Parking Lights Output
[2]
(+) Ignition Input/Output
(-) Ground
(+) 12V
(-) Hood Switch
See page 6 for wiring information
Parking
Lights
OR
Connect for Dodge
Journey only.
This is the only connection required for parking light output for the Dodge Journey, and the DBALL MUX connection is not required
Rev.: 20160907
Page 5
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
Ignition Isolation (veh. side): Yellow: 8
Ignition Isolation (conn. side): Orange/Yellow: 9
(+) 12V (+) 12V: Red: 13
(-) Ground (-) Ground: Black: 14
(-) E-Brake Output: Black/White: 1
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
[1]
(AC) Tach Output: Violet/White: 5
(+) Brake Output: Gray: 6
(MUX) Parking Lights: Violet/Green: 8
(MUX) Parking Lights: Violet/Brown: 9
RAP Off: Yellow/Black: 10
Refer to the Vehicle
Wiring Reference
Charts on page 7 for
CAN wire colors and location.
RF
Prog. Button
LED
DBALL2
10: Blue/White: (-) GWR (Status) Input
9: Pink: (+) Ignition Input
8: Violet: (+) Starter Input
7: Pink/White: (+) Parking Input
5: Violet/Black: (-) Aux2 Input
4: White/Violet: (-) Aux1 Input
3: Red/White: (-) Trunk Input
2: Blue: (-) Unlock Input
1: Green: (-) Lock Input
(+)12V
RX
(-) Ground
TX
P#: XKD2D65
(-) Driver door trigger
Violet wire in driver kick panel
Ignition
Barrel
6
Connector side view at ignition switch
12
1
7
Not required in D2D mode.
[1]
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2]
Connection required for Dodge Journey.
All adapters are displayed from the wire side (unless specified otherwise).
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
2500
3500
C/V
Caravan 2008-10 White/Green Black connector at light switch, pin 3
Challenger 2008+ White/Brown Black connector at light switch, pin 1
Challenger
Black connector at light switch, pin 1
(Smart Key)
Durango 2011+ White/Green Black connector at light switch, pin 3
Grand Caravan 2011+ White/Green Black connector at light switch, pin 3
Grand Caravan
2011+ White
2011+ White
Black connector at light switch, pin 1
Black connector at light switch, pin 1
2012-16 White/Lt. Green Black connector at light switch, pin 3
2008-10 White/Brown Black connector at light switch, pin 1
Passenger kick panel
Black connector at light switch, pin 1
Rev.: 20160907
Page 6
Parking Light Vehicle Wiring Reference Chart (Type 1)
Town & Country
Dodge/Ram
1500
2008-10 White/Brown Black connector at light switch, pin 1
2011+ White Black connector at light switch, pin 1
MUX
8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
MUX
MUX
MUX
MUX
MUX
MUX
MUX
MUX
MUX
MUX
(+)
MUX
8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
Remote Starter (+) Parking Lights
8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
Journey 2009-10 White/Violet
RAM
Jeep
Grand Cherokee
Grand Cherokee
(Smart Key)
Volkswagen
Routan
2009-10 White
2011+ White/Green
2011+ White/Green
2011+ White/Green
Routan
Black connector at light switch, pin 1
Black connector at light switch, pin 1
Black connector at light switch, pin 3
2009-10 White/Brown Black connector at light switch, pin 1
MUX
MUX
8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
MUX
MUX
8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
8: Violet/Green: (MUX) Parking Lights
9: Violet/Brown: (MUX) Parking Lights
Light switch, black 10-pin plug
1
6
2 3 4
7 8 9
5
10
3
2
1
6
5
4
Light switch, black 6-pin plug
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
CAN Vehicle Wiring Reference Chart (Type 1)
Vehicle
Chrysler
Years HS CAN High Pin HS CAN Low
Town & Country
Dodge/Ram
2008+
White/Lt. Blue
5
White/Brown
1500
2500
3500
2011+
White/Lt. Green
5
White/Lt. Blue
2011+
White/Lt. Green
5
White/Lt. Blue
2011+
White/Lt. Green
5
White/Lt. Blue
2012-2015 White/Lt. Blue 5
White/Brown C/V
Caravan
Challenger
2008-10
White/Lt. Blue
5
White/Brown
2008+
White/Black
Challenger (Smartkey)
2008+
White/Black
5
5
White/Lt. blue
White/Lt. blue
Durango
Grand Caravan
Journey
RAM
2011+
White/Lt. Blue
5
White/Brown
2008-11
White/Lt. Blue
5
White/Brown
2009-10
White/Lt. Blue
5
White/Brown
2009-10
White/Lt. Blue
5
White/Brown
Jeep
Grand Cherokee
Grand Cherokee
(Smartkey)
Volkswagen
Routan
2011+
2011+
White/Lt. Blue
White/Lt. Blue
2009-2011 White/Lt. Blue
5
5
5
White/Brown
White/Brown
White/Brown
Pin
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
Rev.: 20160907
Page 7
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Installation Type 2a (with CHTHD1/THCHD1 T-Harness R7)
Refer to the Vehicle Wiring Reference Charts on page 11 for wire color and location.
See page 10 for wiring information
Connect for Jeep
Commander &
Grand Cherokee only.
[2]
(-) Parking Light Output
Parking
Lights
OR
[1]
(AC) Tach Input
(-) Ground
(+) 12V
(-) Hood Switch
(+) Ignition Input/Output
Twisted pair in the steering column or behind radio
White/Orange
White/Gray, White or White/Pink
FT CAN High: White/Orange: 5
FT CAN Low: White: 6
(-) Ground
(+) 12V
(-) Hood Switch
Remote Start Safety
Override Switch is inactive
(used for RSR only)
Rev.: 20160907
Page 8
D2D only
Pink
[1]
(AC) Tach Output: Violet/White: 5
(MUX) Parking Lights: Violet/Green: 8
(MUX) Parking Lights: Violet/Brown: 9
RAP Off: Yellow/Black: 10
(-) Driver door trigger
Violet wire in driver kick panel or driver door (Jeeps ONLY).
RF
Prog. Button
LED
Do
NOT
connect
DBALL2
(+)12V
RX
(-) Ground
TX
P#: XKD2D65
CHTHD1/THCHD1 R7
(optional)
12-pin Connector
(harness side)
12-pin Connector
(harness side)
12-pin Connector
(Vehicle side)
Ignition
Barrel
(vehicle side)
[1]
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2]
Connection only required for Jeep Commander & Jeep Grand Cherokee
Wires not listed in this diagram are not required for the installation.
All adapters are displayed from the wire side (unless specified otherwise).
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Installation Type 2b (with CHTHD1/THCHD1 T-Harness R1-R6)
Refer to the Vehicle Wiring Reference Charts on page 11 for wire color and location.
(-) Ground
See page 10 for wiring information
Connect for Jeep
Commander &
Grand Cherokee only.
[2]
(-) Parking Light Output
(+) 12V
Parking
Lights
OR
(-) Hood Switch
[1]
(AC) Tach Input
Twisted pair in the steering column or behind radio
White/Orange
White/Gray, White or White/Pink
(+) Ignition Input/Output
(-) Ground
(+) 12V
(-) Hood Switch
Rev.: 20160907
Page 9
D2D only
FT CAN High: White/Orange: 5
FT CAN Low: White: 6
Remote Start Safety
Override Switch is inactive
(used for RSR only)
[1]
(AC) Tach Output: Violet/White: 5
(MUX) Parking Lights: Violet/Green: 8
(MUX) Parking Lights: Violet/Brown: 9
RAP Off: Yellow/Black: 10
(-) Driver door trigger
Violet wire in driver kick panel or driver door (Jeeps Only).
RF
Prog. Button
LED
Do
NOT
connect
DBALL2
(+)12V
RX
(-) Ground
TX
P#: XKD2D65
CHTHD1/
THCHD1 R1-R6
(optional)
12-pin Connector
(harness side)
Connect to Red/White wire, pin 3
12-pin Connector
(harness side)
12-pin Connector
(Vehicle side)
Ignition
Barrel
(vehicle side)
[1]
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2]
Connection only required for Jeep Commander & Jeep Grand Cherokee
Wires not listed in this diagram are not required for the installation.
All adapters are displayed from the wire side (unless specified otherwise).
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Rev.: 20160907
Page 10
Installation Type 2c (without T-Harness)
Refer to the Vehicle Wiring Reference Charts on page 11 for wire color and location.
(+) Brake Input
[1]
(AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(-) E-Brake Status Input
[2]
(-) Parking Light Output
(-) Ground
(+) 12V
(-) Hood Switch
(-) Lock Output
(-) Unlock Output
(-) Trunk Output
(+) Starter Output
(-) GWR (Status)
(+) Parking Lights Output
(+) Ignition Input/Output
(-) Ground
(+) 12V
(-) Hood Switch
See page 11 for wiring information
Parking lights output for
Jeep Commander &
Grand Cherokee only.
OR
Parking
Lights
(-) Driver door trigger
Twisted pair in the steering column or behind radio
White/Orange
White/Gray, White or White/Pink
HS CAN High: Tan/Black: 3
HS CAN Low: Tan: 4
FT CAN High: Orange/Green: 5
FT CAN Low: Orange/Brown: 6
Ignition Isolation (veh. side): Yellow: 8
Ignition Isolation (conn. side): Orange/Yellow: 9
(+) 12V (+) 12V: Red: 13
(-) Ground (-) Ground: Black: 14
(-) E-Brake Output: Black/White: 1
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
[1]
(AC) Tach Output: Violet/White: 5
(+) Brake Output: Gray: 6
(MUX) Parking Lights: Violet/Green: 8
(MUX) Parking Lights: Violet/Brown: 9
RAP Off: Yellow/Black: 10
RF
Prog. Button
LED
DBALL2
10: Blue/White: (-) GWR (Status) Input
9: Pink: (+) Ignition Input
8: Violet: (+) Starter Input
7: Pink/White: (+) Parking Lights Input
3: Red/White: (-) Trunk Input
2: Blue: (-) Unlock Input
1: Green: (-) Lock Input
(+)12V
RX
(-) Ground
TX
P#: XKD2D65
Violet wire in driver kick panel or driver door
(Jeeps ONLY).
Ignition
Barrel
6
1
12
Connector side view at ignition switch
7
Not required in D2D mode.
[1]
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
[2]
Connection only required for Jeep Commander & Jeep Grand Cherokee
All adapters are displayed from the wire side (unless specified otherwise).
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Parking Light Vehicle Wiring Reference Chart (Type 2)
Vehicle
Chrysler
300/300c
Dodge
Charger
Years Vehicle Wire Location on vehicle
2008-10 White/Brown Black connector at light switch, pin 1
2008-10 White/Brown Black connector at light switch, pin 1
Magnum 2008 White/Brown Black connector at light switch, pin 1
Jeep
Commander 2008-10 White/Dk. Blue Hazard light switch
Grand Cherokee 2008-10 White/Dk. Blue Hazard light switch
Refer to DirectWire for additional parking light locations.
Polarity
DBALL Output from
12 Pin connector
MUX
8: Violet/Green: (MUX ) Parking Lights
9: Violet/Brown: (MUX ) Parking Lights
MUX
MUX
8: Violet/Green: (MUX ) Parking Lights
9: Violet/Brown: (MUX ) Parking Lights
8: Violet/Green: (MUX ) Parking Lights
9: Violet/Brown: (MUX ) Parking Lights
(-)
(-)
(-) Parking Lights Output
(-) Parking Lights Output
Rev.: 20160907
Page 11
Light switch, black 10-pin plug
1
6
2
7
3
8
4 5
9 10
Jeep Commander & Jeep Grand
Cherokee
ALTERNATIVE parking light connection
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Installation Type 3a (with CHTHD2/THCHD2 T-Harness R9-R10)
Refer to the Vehicle Wiring Reference Charts on pages 15-16 for wire color and location.
Rev.: 20160907
Page 12
(+) Parking Lights
See page 15 for wiring information
D2D only
(-) Ground
(+) 12V
(-) Hood Switch
(+) Ignition Input/Output
(-) Ground
(+) 12V
(-) Hood Switch
[1]
(AC) Tach Input
Remote Start Safety
Override Switch is inactive
(used for RSR only)
Pink
[1]
(AC) Tach Output: Violet/White: 5
RAP Off: Yellow/Black: 10
(-) Driver door trigger
Violet or Violet/Dk. Blue wire in driver kick panel or at driver door module
Do
NOT
connect
RF
Prog. Button
LED
DBALL2
(+)12V
RX
(-) Ground
TX
P#: XKD2D65
Sentry Key Module
Near Ignition Switch
(vehicle side)
CHTHD2/
THCHD2 R9-R10
(optional)
N.C.
T-04
8-pin Connector
(harness side)
8-pin Connector
(harness side)
8-pin Connector at Sentry Key Module Near
Ignition Switch (vehicle side)
[1]
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Wires not listed in this diagram are not required for the installation.
All adapters are displayed from the wire side (unless specified otherwise).
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Installation Type 3b (with CHTHD2/THCHD2 T-Harness R1-R6)
Refer to the Vehicle Wiring Reference Charts on pages 15-16 for wire color and location.
See page 15 for wiring information
(-) Ground
(+) 12V
(-) Hood Switch
(+) Ignition Input/Output
(-) Ground
(+) 12V
(-) Hood Switch
[1]
(AC) Tach Input
(+) Parking Lights
(-) Lock Output
(-) Unlock Output
(-) Trunk Output
(+) Starter Output
(+) Ignition Input/Output
(-) GWR (Status)
Rev.: 20160907
Page 13
D2D only
[1]
(AC) Tach Output: Violet/White: 5
(-) Driver door trigger
RAP Off: Yellow/Black: 10
Violet or Violet/Dk. Blue wire in driver kick panel or at driver door module
Sentry Key Module
Near Ignition Switch
(vehicle side)
CHTHD2/
THCHD2 R1-R6
(optional)
RF
Prog. Button
LED
DBALL2
10: Blue/White: (-) GWR (Status) Input
9: Pink: (+) Ignition Input
8: Violet: (+) Starter Input
3: Red/White: (-) Trunk Input
2: Blue: (-) Unlock Input
1: Green: (-) Lock Input
(+)12V
RX
(-) Ground
TX
P#: XKD2D65
8-pin Connector at Sentry Key Module Near
Ignition Switch (vehicle side)
8-pin Connector
(harness side)
8
8-pin Connector
(harness side)
Connect to Red/White wire, pin 3 (male plug)
3
1
Wire side view
(T-Harness 8-pin Conn.)
[1]
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
Wires not listed in this diagram are not required for the installation.
All adapters are displayed from the wire side (unless specified otherwise).
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Installation Type 3c (without T-Harness)
Refer to the Vehicle Wiring Reference Charts on pages 15-16 for wire color and location.
(-) Ground
(+) 12V
(-) Hood Switch
(+) Brake Input
[1]
(AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(-) E-Brake Status Input
(-) Ground
(+) 12V
(-) Hood Switch
(+) Parking Lights
(-) Lock Output
(-) Unlock Output
(-) Trunk Output
(+) Starter Output
(+) Ignition Input/Output
(-) GWR (Status)
See page 15 for wiring information
Rev.: 20160907
Page 14
(+) 12V
(-) Ground
FT CAN High: Tan/Black: 3
FT CAN Low: Tan: 4
(+) 12V: Red: 13
(-) Ground: Black: 14
(-) E-Brake Output: Black/White: 1
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
[1]
(AC) Tach Output: Violet/White: 5
(+) Brake Output: Gray: 6
Multiplex Output: Violet/Green: 8
Multiplex Output: Violet/Brown: 9
RAP Off: Yellow/Black: 10
RF
Prog. Button
LED
(-) Driver door trigger
DBALL2
10: Blue/White: (-) GWR (Status) Input
9: Pink: (+) Ignition Input
8: Violet: (+) Starter Input
3: Red/White: (-) Trunk Input
2: Blue: (-) Unlock Input
1: Green: (-) Lock Input
(+)12V
RX
(-) Ground
TX
P#: XKD2D65
Violet or Violet/Dk. Blue wire in driver kick panel or at driver door module
Refer to the Vehicle
Wiring Reference
Charts on page 16 for CAN wire colors and location.
1 8
Sentry Key Module Near Ignition Switch
(connector side view)
Not required in D2D mode.
[1]
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
All adapters are displayed from the wire side (unless specified otherwise).
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Rev.: 20160907
Page 15
Parking Light Vehicle Wiring Reference Chart (Type 3)
Vehicle Years Wire
Chrysler
200
Aspen
Sebring
2011-14 White/Violet
2007-09 Pink/Red
2007-10 White/Violet
Sebring Convertible 2008-10 White/Violet
Sebring Sedan 2007-10 White/Violet
Dodge
Avenger 2008+ White/Violet
Caliber
Dakota
Durango
Nitro
2007-12 White/Violet
2007-11 Pink/Red
2007-09 Pink/Red
2007-11 White/Violet
RAM
White/Yellow (L),
White/Gray
2006-08
OR
White/Lt.Green
Polarity Location
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
(+)
Driver kick panel
Driver kick fuse box, black 40-pin plug, pin 6
Driver kick panel
Driver kick panel
Driver kick panel
Driver kick panel
Driver kick panel
Underhood fuse box, black 20-pin plug, pin 15
Driver kick fuse box, black 40-pin plug, pin 6
Driver kick panel
Totally Integrated Power Module under hood, connector C9 pin 8,10
Use (2) 6 Amp diodes to isolate left and right parking lights.
MUX
Headlight switch.
Use a resitor and relay, see Tech Tip 1082
Multiplex Light Circuit Integration.
Jeep
Compass
Liberty
Patriot
Wrangler
Wrangler Limited
Driver kick fuse box, black 40-pin plug
2007+ White/Violet
2008-12 White/Violet
2007+ White/Violet
2007+ White/Violet
2007+ White/Violet
(+)
(+)
(+)
(+)
(+)
Driver kick panel
Driver kick panel
Driver kick panel
Passenger kick panel
Passenger kick panel
Underhood fuse box, black 20-pin plug
Above driver kick, gray 74-pin plug
1 7 38 44
10 9 8 7 6 5 4 3 2 1
20 19 18 17 16 15 14 13 12 11
39
37
36 24
29
25 9
33 21
28 12
17 5
20
13
8
1
3
Module-Totally Integrated Power C9
6
12
1
7
3
10
11
20
29
14
15
16
17
58
59
60
61
46
55
64
65
38 4 72
40 32
16
2
31 37 68 74
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
CAN Vehicle Wiring Reference Chart (Type 3)
FT CAN High FT CAN Low Vehicle
Chrysler
200
Years
Aspen
Sebring
2011-14
2007-09
2007-10
Sebring Convertible 2007-10
Sebring Sedan
Dodge/Ram
2007-10
Avenger
Caliber
Dakota
Durango
2008-14
2007-12
2007-11
2007-09
Nitro 2007-11
RAM
Jeep
Compass
Liberty
Patriot
Wrangler
Mitsubishi
Raider
2006-08
2007-16
2008-12
2007-16
2007-16
2007-09
White/Orange White
White/Orange White
White/Orange White
White/Orange White
White/Orange White
White/Orange White
White/Orange White/Pink
White/Orange White
White/Orange White
White/Black or
White/Lt.Green
White/Lt.Blue
White/Orange White
White/Orange White/Pink
White/Black White/Lt.Blue
White/Orange White/Pink
White/Black White/Lt.Blue
White/Orange White
Rev.: 20160907
Page 16
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Installation Type 4
(-) Ground
(+) 12V
(-) Hood Switch
(+) Brake Input
[1]
(AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(-) E-Brake Status Input
(-) Ground
(+) 12V
(-) Hood Switch
Rev.: 20160907
Page 17
Parking Lights
See page 18 for wiring & polarity information
(-) Lock Output
(-) Unlock Output
(-) Trunk Output
(-) Aux 2 Heated Seat Activation
(+) Starter Output
(+) Ignition Input/Output
(-) GWR (Status)
(+) 12V
(-) Ground
FT CAN High: Tan/Black: 3
FT CAN Low: Tan: 4
(+) 12V: Red: 13
(-) Ground: Black: 14
(-) E-Brake Output: Black/White: 1
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
[1]
(AC) Tach Output: Violet/White: 5
(+) Brake Output: Gray: 6
Multiplex Output: Violet/Green: 8
Multiplex Output: Violet/Brown: 9
RF
Prog. Button
LED
DBALL2
10: Blue/White: (-) GWR (Status) Input
9: Pink: (+) Ignition Input
8: Violet: (+) Starter Input
5: Violet/Black: (-) Aux2 Input
3: Red/White: (-) Trunk Input
2: Blue: (-) Unlock Input
1: Green: (-) Lock Input
(+)12V
RX
(-) Ground
TX
P#: XKD2D65
5 or 6
Refer to the Vehicle
Wiring Reference
Charts on page 18 for
Start wire colors.
1
Sentry Key Module
Near Ignition Switch
(connector side view)
8
Ignition Switch
(connector side view)
1
Not required in D2D mode.
[1]
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
All adapters are displayed from the wire side (unless specified otherwise).
© 2016 Directed. All rights reserved.
3
10
11
20
29
14
15
16
17
Platform: DBALL2
Firmware: CHRYSLER
Parking Light Vehicle Wiring Reference Chart (Type 4)
Vehicle
Chrysler
300/300c
PT Cruiser
Dodge
Caliber
Charger
Magnum
RAM
Jeep
Commander
Grand Cherokee
Above driver kick, gray 74-pin plug
1 7 38 44
Years Wire
2005-07 White/Violet
2006-10 White/Violet
2007 White/Violet
2006-07 White/Violet
2005-07 White/Violet
2006 White/Gray
2006-07 White/Dk. Blue
2005-07 White/Dk. Blue
Polarity Location
(+)
(+)
(+)
(+)
(+)
(+)
(-)
(-)
Passenger kick panel
Driver kick panel
Driver kick panel
Passenger kick panel
Passenger kick panel
Above driver kick, gray 74-pin plug, pin 19
Hazard light switch
Hazard light switch
58
59
60
61
46
55
64
65
72
31 37 68 74
Start - Vehicle Wiring Reference Chart (Type 4)
Vehicle
Chrysler
300/300c
PT Cruiser
Dodge
Caliber
Charger
Magnum
RAM
Jeep
Commander
Grand Cherokee
Years Wire
2005-07 Pink/Dk. Green
2006-10 Pink/Lt.Blue
2007 Pink/Lt.Blue
2006-07 Pink/Dk. Green
2005-07 Pink/Dk. Green
2006 Dk. Green/Yellow
2006-07 Pink/Orange
2005-07 Pink/Orange
Polarity Location
(+) At ignition switch, black 5-pin plug
(+) At Ignition harness
(+) At ignition switch, black 5-pin plug
(+) At ignition switch, black 5-pin plug
(+) At ignition switch, black 5-pin plug
(+) At ignition harness or starter button (SRT-10)
(+) At Ignition harness
(+) At Ignition harness
Rev.: 20160907
Page 18
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Installation Type 5
See page 20 for the ignition switch wiring information
Ignition Switch
(black connector)
(-) Keysense: Violet/Tan, pin 5
4
3
2
1
7
6
5
11
10
9
8
14
13
12
*Pin 1 or 8 depending on the vehicle (see page 20).
(+) 12V
86 87
87a
30
85
(+) 12V or (-) Ground (see page 20)
(-) Ground (-) Ground
(+) 12V
(+) Accessory 1
(+) Starter
(+) Ignition 1
(+) Ignition 2
(-) Accessory 2
(+) Brake Input
[1]
(AC) Tach Input
(-) Trunk Status Input
(-) Door Status Input
(-) E-Brake Status Input
Connect Keysense wire only if vehicle is equipped with OEM alarm.
Diode
Rev.: 20160907
Page 19
(-) Hood Switch (-) Hood Switch
See page 20 for wiring information
(+) Parking Lights
(-) Lock Output
(-) Unlock Output
(-) GWR (Status)
(+) 12V
(-) Ground
FT CAN High: Tan/Black: 3
FT CAN Low: Tan: 4
(+) 12V: Red: 13
(-) Ground: Black: 14
(-) E-Brake Output: Black/White: 1
(-) Door Status Output: Green/White: 3
(-) Trunk Status Output: Red/Black: 4
[1]
(AC) Tach Output: Violet/White: 5
(+) Brake Output: Gray: 6
10: Blue/White: (-) GWR (Status) Input
2: Blue: (-) Unlock Input
1: Green: (-) Lock Input
RF
Prog. Button
LED
DBALL2
(+)12V
RX
(-) Ground
TX
P#: XKD2D65
1 8
Sentry Key Module
Near Ignition Switch
(connector side view)
Not required in D2D mode.
[1]
Tach wire is an optional connection required on some remote starters, which do not support a tach signal in D2D.
All adapters are displayed from the wire side (unless specified otherwise).
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Rev.: 20160907
Page 20
Vehicle Wiring Reference Chart (Type 5)
* Vehicle may not have an Accessory 2 wire in pin 1 or 8. If that is the case, this connection is unnecessary.
Vehicle Years
Wire
Dodge
Dakota 2005 Pink/Red
Parking Lights
Polarity Location
(+)
Dakota
Durango
Durango 2005-06 Pink/Red
Mitsubishi
2006
2004
Pink/Red
Pink/Red
(+)
(+)
(+)
12 V Starter Ignition Ignition 2
Underhood fuse box, black
20-pin plug, pin 15
Underhood fuse box, black
20-pin plug, pin 15
Driver kick fuse box, black
40-pin plug, pin 6
Driver kick fuse box, black
40-pin plug, pin 6
Red, pin 7
Red, pin 7
Red/Dk. Blue, pin 7
Red/Dk. Blue, pin 7
Pink/Lt. Blue, pin 13
Pink/Lt. Blue, pin 13
Pink/Lt. Blue, pin 13
Pink/Lt. Blue, pin 13
Pink/Lt. Green,
Pink, pin 2 pin 3
Pink/Lt. Green,
Pink, pin 2 pin 3
Pink/Lt. Green,
Pink, pin 2 pin 3
Pink/Lt. Green,
Pink, pin 2 pin 3
Accessory
Ignition Switch, black 14-pin plug
Pink/White, pin 14
Pink/White, pin 14
Pink/Yellow, pin 14
Pink/Yellow, pin 14
Raider 2006 Pink/Red (+)
Underhood fuse box, black
20-pin plug, pin 15
Red, pin 7
Pink/Lt. Blue, pin 13
Pink/Lt. Green,
Pink, pin 2 pin 3
Pink/White, pin 14
Accessory 2*
Dk. Blue (+), pin 8
Violet (-), pin 1
Dk. Blue (+), pin 8
Violet (-), pin 1
Violet (-), pin 1
Driver kick fuse box, black 40-pin plug
Ignition switch, black 14-pin plug
Underhood fuse box, black 20-pin plug
10 9 8 7 6 5 4 3 2 1
20 19 18 17 16 15 14 13 12 11
39
37
38
40
25 9
33 21
28 12
17 5
36 24
29
32
20
13
8
16
4
2
1
3
3
2
1
7
6
5
4
10
9
8
14
13
12
11
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Rev.: 20160907
Page 21
Module Programming
Refer to the LED Diagnostics section on page 26 for more information and for troubleshooting purposes.
Important
Make all the required connections to the vehicle, as described in the wiring diagram(s) found in this guide, and double check to ensure everything is correct prior to moving onto the next step.
Warning!
To take advantage of advanced features, you must use XpressVIP 4.5 (and higher) or the Directechs Mobile app.
Flashing a module using your computer:
1. Connect the interface module to your computer using the
XKLoader2.
2. Go to www.directechs.com using Internet Explorer, and select the Flash Module button.
3. Follow the instructions to select your vehicle, installation type, and configure your options.
4. Once you have configured the firmware options, click on the
FLASH button.
Flashing a module using your smartphone or tablet
1. Connect the interface module to your XKLoader3.
2. Launch the Directechs Mobile app on your smartphone or tablet.
3. Select FLASH YOUR MODULE and follow the on screen instructions.
When the flashing operation is successful, you can proceed with the programming instructions below.
D2D Installation
If required for your installation, connect the 10-pin, 12-pin and 14-pin harnesses to the module, then connect the 4-pin D2D harness.
4 th
1 st
OR
W2W Installation
If required for your installation, connect the 10-pin and 12-pin harnesses to the module, then connect the 14-pin harness to the module.
1 st
D2D
10-pin
3 rd
2 nd
3 rd
2 nd
14-pin
12-pin
14-pin
12-pin
Vehicles WITH Factory Keyless
(Refer to the next page for programming instructions WITHOUT factory keyless.)
1
Wait until the LED turns ON solid red.
2
Solid
Key Ignition
Insert the key into the ignition barrel and turn it to the ON position.
It is important to wait for the LED to start flashing green. Refer to the LED Diagnostics section on page 25 for troubleshooting if the LED does not flash green within 15 seconds.
or
Key IN
O
N
START
&
Flashes Green
Push-to-Start (PTS) Ignition
Important: Do NOT press the brake pedal.
Press the Push-to-Start (PTS) button twice to turn the ignition ON.
Do NOT press the brake pedal
2X
ENGINE
START
STOP
PUSH
It is important to wait for the LED to start flashing green. Refer to the LED
Diagnostics section on page 25 for troubleshooting if the LED does not flash green within 15 seconds.
Flashes Green
Go to the next page to complete the module programming.
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Rev.: 20160907
Page 22
3
Turn the key to the OFF position and remove it from the ignition barrel.
Key OUT
IG
N
START
or
Press the Push-to-Start
(PTS) button once more to turn the ignition OFF.
4
Press LOCK or UNLOCK on the
factory transmitter. The LED turns ON solid green OR orange for 3 seconds and then turns off.
or
You have successfully completed the module programming sequence.
1X
ENGINE
START
STOP
PUSH
& or
Solid Green Solid Orange
&
Off
Vehicles WITHOUT Factory Keyless
(Refer to the previous page for programming instructions WITH factory keyless.)
1
Wait until the LED turns ON solid red.
2
Insert the key into the ignition barrel and turn it to the ON position.
It is important to wait for the LED to start flashing green.*
* Refer to the LED Diagnostics section on page 25 for troubleshooting
if the LED does not flash green within 15 seconds.
3
Turn the key to the OFF position and remove it from the ignition barrel.
Key IN
Solid
O
N
START
&
Flash Green
Key OUT
IG
N
START
4
Press and release the Programming Button. The LED turns ON solid green OR orange for 3 seconds and then turns OFF.
Press & Release
&
Solid
or
Solid
&
Off
You have successfully completed the module programming sequence.
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Rev.: 20160907
Page 23
Module Reset
A module reset will erase the module programming only (bypass, convenience and vehicle detection). All the settings configured on the module using the web config tool will remain untouched.
1
D2D Installation
If required for your installation, connect the 10-pin, 12-pin &
14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.
OR
W2W Installation
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
5 th
1 st
1 st
3 rd
2 nd
4 th
4 th
2 nd
3 rd
14-pin
12-pin
2
Wait 3 seconds until the LED turns ON solid orange then release the programming button. The LED then turns ON solid red.
Solid
&
Release
&
Solid
Hard Reset
Warning Against Executing a Hard Reset!
A hard reset will revert the flashed firmware back to its default settings. Depending on the installation, some settings (such as RFTD and D2D options) may have to be reconfigured. See the Feature & Option List section of this guide.
D2D Installation
If required for your installation, connect the 10-pin, 12-pin &
14-pin harnesses to the module. Press and hold the programming button, then connect the 4-pin D2D harness.
1
OR
W2W Installation
If required for your installation, connect the 10-pin & 12-pin harnesses to the module. Press and hold the programming button, then connect the 14-pin harness to the module.
5 th
1 st
1 st
3 rd
2 nd
4 th
4 th
2 nd
3 rd
14-pin
12-pin
2
Wait 3 seconds until the LED turns ON solid orange, and wait 10 more seconds until the LED starts to flash orange and red.
Solid
&
Flashes
3
Release the programming button. The LED turns ON solid red.
Release
&
Solid
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Rev.: 20160907
Page 24
Feature & Option List
It is recommended to configure all the features and options listed below using the configuration tool found on the module flashing page on www.directechs.com. The web offers more options; however, manual configuration of the features is possible using the information on this page.
* Default option
Feature Operation
1
2
3
4
5
6
7
8
9
RF Output Type
1. Driver Priority*
Unlock Driver Priority
Trunk
Aux1
2. All
1. Trunk*
2. Right Sliding Door
3. Left Sliding Door
1. Trunk
2. Right Sliding Door*
3. Left Sliding Door
1. Disabled
1. Trunk
Aux2
2. Right Sliding Door
3. Left Sliding Door*
Heated Seats
1. Disabled*
2. Enabled
Heated Seats/Defrost Temperature
Control
1. 32° Farenheit (0° Celsius)*
(Feature 6 must be enabled )
2. 23° Farenheit (-5° Celsius)
Note: If the Heated Steats feature is activated, it can always be turned on using the Aux2 command, regardless of the temperature setting.
Heated Seats Temperature Level
(Feature 6 must be enabled )
3. 41° Farenheit (5° Celsius)
4. Always ON
1. High*
2. Low
Smart OEM Alarm Control
Flashes / Option
1. Disabled*
2. RFTD Output
3. SmartStart
1. Disabled
2. Safelock
3. Enabled*
Description
Module is connected to a remote starter using a standard installation.
Module is connected to an XL202 using an RSR or RXT installation (when available).
Module is connected to SmartStart using an RSR or RXT installation (when available).
Unlocks only the driver door on first press and unlocks all doors on a second press within 5 seconds.
Unlocks all doors on first press.
Will pop the trunk if available.
When available, will operate the right sliding door.
When available, will operate the left sliding door.
Trunk: Will pop the trunk if available.
When available, will operate the right sliding door.
When available, will operate the left sliding door.
3./4. Right/Left Sliding Door: When available, will operate the sliding door.
Will pop the trunk if available.
When available, will operate the right sliding door.
When available, will operate the left sliding door.
No operation.
If available, it will activate the Heated Seats Control feature (see feature #7)
When feature #6 (Heated Seats) is enabled, it will activate the heated seats upon remote start when temperature is below 32 °F (0 °C).
When feature #6 (Heated Seats) is enabled, it will activate the heated seats upon remote start when temperature is below 23 °F (-5 °C).
When feature #6 (Heated Seats) is enabled, it will activate the heated seats upon remote start when temperature is below 41 °F (5 °C).
When feature #6 (Heated Seats) is enabled, it will activate the heated seats at any temperature.
When Heated Seats are activated, they will be set to HIGH.
When Heated Seats are activated, they will be set to LOW.
The OEM alarm will not be controlled by DBALL upon remote start. No disarm or arm command will be executed at the beginning or end of the sequence; it must be controlled by the Remote Starter.
Smart OEM Alarm Control will behave like a standard Safelock feature on a remote starter. It will unlock at the beginning of the sequence, and relock after start and shutdown.
Smart OEM Alarm Control will synchronize with the OEM alarm so that it will disarm and rearm the vehicle in the remote start sequence, only when required. The reason for this is, factory alarm control must often be done by lock or unlock operation. This could create unnecessary actions on door lock modules, such as the horn to honk. When possible, Smart OEM Alarm
Control will monitor the alarm and door lock status to detect if the disarm or rearm is required. If the vehicle is unlocked or is not equipped with factory alarm, the disarm/rearm will not be executed. Smart OEM Alarm Control will also monitor the remote starter actions so that the factory alarm control is not done twice. A remote starter, for which the Safelock feature is active, will work perfectly with this option and will make it invisible to the user.
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Rev.: 20160907
Page 25
Feature Programming
Programming
Button
To enter feature programming routine
Turn the ignition ON, then OFF.
Within 5 seconds, press and HOLD the programming button until the LED turns ON orange (after 3 seconds). Release the
-
Programming button.
The LED will flash green once slowly to indicate the feature number is 1. After a short delay, the LED flashes red rapidly to indicate the current option of feature 1 (i.e. 1x green followed by 1x red indicates feature 1 is set to option 1). The flashing sequence will repeat until a new command is entered.
Changing feature options
Press the lock/arm or unlock/disarm button on aftermarket transmitter to change the option of the selected feature.
The LED flashes red rapidly the number of times equal to the current option number. After a short delay, the LED flashes green slowly the number of times to indicate the current feature. The flashing sequence will repeat until a new command is entered.
Accessing another feature
Press and release the programming button a number of times to advance from the current feature to the next desired feature.
-
The LED flashes green slowly the number of times equal to the feature number. After a short delay, the LED flashes red rapidly to indicate the current option of the current feature. The flashing sequence will repeat until a new command is entered.
When the maximum number of features or options is reached, the LED will start flashing again from the first feature or option.
Once a feature is programmed
Other features can be programmed.
-
The feature programming can be exited.
Exiting feature programming
No activity for 30 seconds; after 30 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence.
-
OR
Press and HOLD the programming button for 3 seconds. After 3 seconds, the LED will turn ON orange for 2 seconds to confirm the end of the programming sequence.
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
LED Diagnostics & Troubleshooting
Troubleshooting LED Description
Module Programming
Off
Module has no power.
Check the power connections.
Solid red
Flashes orange
The bus type cannot be detected.
Make sure the connections to the data bus are correct and insert the key in the ignition switch.
The vehicle type cannot be detected.
Insert the key in the ignition switch and turn to the ON position.
You may need to wait up to 10 seconds.
Flashes green
Waiting for keyless.
Remove the key from the ignition switch and press a keyless button.
Solid green x3 secs
Solid orange x3 secs
Flashes red & orange
Module was successfully programmed or is already programmed.
Module was successfully programmed without diagnostics.
Active Ground While Running
Flashes green
GROUND OUT ON (GWR) command received.
IGNITION ON command received.
Normal operation.
Normal operation.
Otherwise, the Ground While Running (status) signal was lost or was never received by the module.
Commands can come from RF, D2D or W2W.
Otherwise, the ignition signal was not received by the module. In a W2W install, it will show only if the ignition input wire is used.
Flashes green quickly
START ON command received.
External Module Synchronization
Otherwise, the start signal was not received by the module. In a W2W install, it will show only if the ignition input wire is used.
OBDII feature not supported.
Diagnostic data bus not detected.
(Flashes red, red, then orange) x 10
D2D and W2W Commands
Flashes orange x1
LOCK command has been received
Some features are not supported by SmartStart. This can be caused by missing wire connections or module hardware limitation. Refer to the wiring installation section to check the connections.
Flashes orange x2
Flashes orange x3
UNLOCK command has been received
TRUNK command has been received
Normal operation.
Flashes orange x4
AUX1 command has been received
Rev.: 20160907
Page 26
Flashes orange x5
AUX2 command has been received
© 2016 Directed. All rights reserved.
Platform: DBALL2
Firmware: CHRYSLER
Rev.: 20160907
Page 27
Limited One Year Consumer Warranty
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed
Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the “Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING
BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY,
FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL
PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY
PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS
PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF
THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR
INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS,
AND DIRECTED HEREBY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION,
LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING
DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF
CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE
DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED
TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL NOT BE
RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL
DAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL
LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE
MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION THE
PART AS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of
America or Canada are sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in connection with this Part.
For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website at: www.directed.com
920-10012-01 2013-07
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.: Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product only.
Protected by U.S. Patents: 5,719,551; 6,011,460 B1 *; 6,243,004 B1; 6,249,216 B1; 6,275,147 B1; 6,297,731 B1; 6,346,876
B1; 6,392,534 B1; 6,529,124 B2; 6,696,927 B2; 6,756,885 B1; 6,756,886 B2; 6,771,167 B1; 6,812,829 B1; 6,924,750 B1;
7,010,402 B1; 7,015,830 B1; 7,031,826 B1; 7,046,126 B1; 7,061,137 B1; 7,068,153 B1; 7,205,679 B1; Cdn. Patent:
2,320,248; 2,414,991; 2,415,011; 2,415,023; 2,415,027; 2,415,038; 2,415,041; 2,420,947; 2,426,670; 2,454,089; European
Patent: 1,053,128; Pat. Pending: 2,291,306. Made in Canada.
© 2016 Directed. All rights reserved.
Quick Reference Guide
DBALL/DBALL2-CHRYSLER
Vehicle Takeover
The Vehicle Takeover and Pit Stop Mode with Push-to-Start (PTS) is applicable only to vehicles with a smart key.
Pit Stop Mode
The Pit Stop Mode feature is practical when you need to stop and run an errand, but wish to keep the engine running.
1
Press the remote start button on the transmitter to start the vehicle.*
Press remote start button*
1
Stop the vehicle in a safe parking spot and put the gear in Park (P).
&
P
Stop & put vehicle in Park (P)
2
Enter the vehicle, while making sure the key is inside with you.
Enter vehicle with Smart Key
3
Important: Do NOT press the brake pedal.
Press the PTS button twice to turn the ignition ON.
Do NOT press brake pedal
2X
ENGINE
START
STOP
PUSH
4
Press the brake pedal, put the car in gear and drive off.
Ready to drive off
* Your remote may differ from the model shown in the illustrations.
2
3
Press the button to remote start the vehicle.*
Press the PTS button once.
Press remote start button*
ENGINE
START
STOP
PUSH
4
It is now safe to leave the engine running and exit the vehicle with the Smart Key in hand.
Note: We recommend that you always lock the doors of your vehicle when leaving it unattended.
Exit vehicle with
Smart Key
* Your aftermarket remote may differ from the model shown in the illustrations.
Notes
© 2016 Directed. All rights reserved.
advertisement
Key Features
- All-in-one door lock and override module
- Compatible with Chrysler, Dodge, Jeep, and Volkswagen vehicles
- Can be flashed and configured using DirectLink or the Directechs Mobile app
- Offers features like remote start, parking lights control, and immobilizer bypass
- Provides detailed wiring diagrams for different vehicle types
- Includes troubleshooting and diagnostic information
- Features a limited one year consumer warranty
Frequently Answers and Questions
What vehicles are compatible with the DBALL2 CHRYSLER?
How do I flash and program the DBALL2 CHRYSLER module?
What are the different installation types available for the DBALL2 CHRYSLER?
How can I troubleshoot any issues with the DBALL2 CHRYSLER module?
Related manuals
advertisement