Yamaha BD-S1067 Owner's Manual
advertisement
BLU-RAY DISC PLAYER
BD-S1067
OWNER’S MANUAL
MANUAL DE INSTRUCCIONES
LVP
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.
2 Install this unit in a well ventilated, cool, dry, clean place – away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following minimum clearances.
Top: 10 cm (4 in)
Rear: 10 cm (4 in)
Sides: 10 cm (4 in)
3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and liquid may cause electrical shock to the user and/or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all connections are complete.
8 Do not operate this unit upside-down. It may overheat, possibly causing damage.
9 Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable.
11 Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury.
Yamaha will not be held responsible for any damage resulting from use of this unit with a voltage other than specified.
13 To prevent damage by lightning, keep the power cable disconnected from a wall outlet or this unit during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The cabinet should never be opened for any reasons.
15 When not planning to use this unit for long periods of time
(i.e. vacation), disconnect the AC power plug from the wall outlet.
16 Be sure to read the “TROUBLESHOOTING” section on common operating errors before concluding that this unit is faulty.
17 Before moving this unit, press p to set this unit to the standby mode, and disconnect the AC power plug from the wall outlet.
18 Condensation will form when the surrounding temperature changes suddenly. Disconnect the power cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may become warm. Turn the power off, then leave this unit alone for cooling.
20 Install this unit near the AC outlet and where the AC power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off by p. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
The laser component in this product is capable of emitting radiation exceeding the limit for Class 1.
LASER Specification:
Class 1 LASER Product
Wave length: 790 nm (CDs)/655 nm (DVDs)/405 nm (BDs)
Laser output: max. 1 mW
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a qualified service person should remove the cover or attempt to service this device.
DANGER
This unit emits visible laser radiation when open. Avoid direct eye exposure to beam. When this unit is plugged into the wall outlet, do not place your eyes close to the opening of the disc tray and other openings to look into inside.
CAUTION
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
Caution-i
En
1. INTRODUCTION
WHAT YOU CAN DO WITH THIS PLAYER........ 2
SUPPLIED PARTS .............................................. 2
ABOUT DISCS AND FILES................................. 3
Types of discs/files that can be used with this Player .... 3
Loading a disc................................................................. 4
Disc precautions ............................................................. 4
CONTROLS AND FUNCTIONS .......................... 5
Front panel...................................................................... 5
Remote control ............................................................... 6
2. CONNECTION
INTRODUCTION TO CONNECTIONS .............. 10
Rear panel ..................................................................... 10
HDMI CONNECTION ......................................... 12
Connecting to the HDMI terminal................................ 12
VIDEO CONNECTIONS .................................... 13
Connecting to the component/video jack ..................... 13
AUDIO CONNECTIONS .................................... 14
Connecting to the digital audio jack/terminal............... 14
Connecting to the audio jacks....................................... 15
NETWORK AND USB CONNECTION .............. 16
Connecting to the NETWORK terminal and
USB port .................................................................. 16
OTHER CONNECTIONS ................................... 17
Connecting to the REMOTE CONTROL jacks ........... 17
Connecting the power cable ......................................... 17
3. PLAYBACK
INITIAL WIZARD/EASY SETUP........................ 18
Setting with the Initial Wizard/Easy Setup................... 18
HOME/MEDIA MENU ........................................ 19
Playing back photo/music/video................................... 19
Using network content.................................................. 21
ADVANCED PLAYBACK OPERATION............ 22
On Screen menu............................................................ 22
Status menu................................................................... 23
Using Bookmark........................................................... 24
Program play................................................................. 24
Using search ................................................................. 24
Enjoying BONUSVIEW and BD-Live......................... 25
Using Picture in Picture function
(secondary audio/video playback) ........................... 25
Using the feature of BD-Live ....................................... 25
4. SETTINGS
SETUP MENU.................................................... 26
Example of SETUP menu operation ............................ 28
General Setting ............................................................. 29
Display Setting ............................................................. 31
Audio Setting................................................................ 33
System Information ...................................................... 33
About the audio output formats .................................... 34
About the video output formats .................................... 35
SOFTWARE UPGRADE.................................... 36
Upgrading the software ................................................ 36
CONTENTS
1
5. ADDITIONAL INFORMATION
TROUBLESHOOTING ....................................... 37
Power ............................................................................ 37
Basic operation.............................................................. 37
Disc playback ................................................................ 37
Picture ........................................................................... 38
Sound ............................................................................ 38
Network......................................................................... 39
Messages on the screen ................................................. 39
GLOSSARY ....................................................... 40
SPECIFICATIONS ............................................. 41
General .......................................................................... 41
Audio performance ....................................................... 41
Input/output ................................................................... 41
Copyright ...................................................................... 42
(at the end of this manual)
Information about software ....................................i
2
3
4
5
■ About this manual
– This manual describes how to operate this Player using a remote control except when it is not available. Some of these operations are also available using the front panel buttons.
– Notes contain important information about safety and operating instructions. Hint(s) indicates a tip for your operation.
– This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and the product, the product has priority.
The icons used in this manual
Icons are used to indicate available buttons/functions for a particular format.
BD : BD-Video
DVD
CD
: DVD-Video, DVD-VR, DVD+VR, DVD-Audio
: Audio CD, Super Audio CD
VIDEO
MUSIC
PHOTO
: AVCHD, WMV, DivX
: MP3, WMA
: JPEG
1
En
INTRODUCTION
WHAT YOU CAN DO WITH THIS PLAYER
Easy setting for language, resolution, screen aspect ratio
You can perform language and TV settings.
Play back commercially-released BD/DVD/CD/SA-CD/DVD-Audio discs
*
In addition to BD discs, this Player also supports playback of a variety of other discs.
\
p. 18
\
p. 22
Play back BONUSVIEW, BD-Live, etc.
*
You can enjoy additional movies on the latest BD discs.
\
p. 25
Play back Video, Music, Photo files on a disc
*
This Player can play back discs you recorded.
\
p. 19
Play back Video, Music, Photo files on a disc/USB memory device
* \
p. 19
Files recorded on discs/USB memory devices can be played back with this Player.
Play back Video, Music, Photo files on a Home Network Server
* ** \
p. 21
PC contents can be played back with TV or AV receiver by connecting this Player to a network server.
Operation with the remote control of TV, AV receiver, etc.
Connecting devices with an HDMI cable, you can control devices with a single remote control using the HDMI Control function.
\
p. 29
* For details on playable disc and format, see page 3.
** Network setting is needed to use this function.
SUPPLIED PARTS
Make sure the following accessories are provided with the product.
Remote control Batteries (×2)
(AAA, R03, UM-4)
Audio pin cable Video pin cable Power cable
2
En
ABOUT DISCS AND FILES
■ Types of discs/files that can be
used with this Player
– 12 cm (5”) and 8 cm (3”) discs can be played back in this Player. Do not use an 8 cm (3”) to 12 cm (5”) adapter.
– Use discs that conform to compatible standards as indicated by the presence of official logos on the disc label. Playback of discs not complying with these standards is not guaranteed. In addition, the image quality or sound quality is not guaranteed even if the discs can be played back.
Disc Type
Recording
Format
BD-Video BD-ROM/BD-R/
BD-RE
DVD-ROM
DVD-R/DVD-R DL/
DVD-RW
DVD+R/DVD+R
DL/DVD+RW
CD-ROM
CD-R/CD-RW
DVD-Video/DVD-
Audio
DVD-Video/DVD-
VR/AVCHD/Data
Disc
DVD-Video/
DVD+VR/AVCHD/
Data Disc
CDDA/HDCD
CDDA/Data Disc
--
--
Data Format
DivX/WMV/MP3/
WAV/WMA/JPEG
DivX/WMV/MP3/
WAV/WMA/JPEG
SA-CD
USB
Network
SA-CD
--
--
--
DivX/WMV/MP3/
WAV/WMA/JPEG
--
DivX/WMV/MP3/
WAV/WMA/JPEG
WMV/MP3/WMA/
WAV/JPEG
Asia
Region management information
Destination BD-Video DVD-Video
Region code “A” or
“ALL”
Region number “3” or “ALL”
Taiwan
Korea
3 ALL
Region code “A” or
“ALL”
Region number “3” or “ALL”
3 ALL
Region code “A” or
“ALL”
Region number “3” or “ALL”
3 ALL
Region management information
Destination
Central and South
America
BD-Video
Region code “A” or
“ALL”
DVD-Video
Region number “4” or “ALL”
Europe
Russia
4 ALL
Region code “B” or
“ALL”
Region number “2” or “ALL”
2 ALL
Region code “C” or
“ALL”
Region number “5” or “ALL”
5 ALL
– BD/DVD Video players and discs have region codes, which dictate the regions in which a disc can be played.
– BD/DVD Video operations and functions may be different from the explanations in this manual and some operations may be prohibited due to disc manufacturer’s settings.
– If a menu screen or operating instructions are displayed during playback of a disc, follow the operating procedure displayed.
Notes
– Playback for some of the discs in the left side column tables may not be possible depending on the disc.
– Finalize all recording media that is played back in this Player.
– “Finalize” refers to a recorder processing a recorded disc so that it will play in other players/recorders as well as this Player. Only finalized discs will play back in this Player. (This Player does not have a function to finalize discs.)
– Playback of all files on the disc, USB memory device and network is not guaranteed.
– A copyright protected file cannot be played back via
USB memory device and network.
MP3/WMA/WAV audio file requirement
– Sampling frequency: within 32 - 48 kHz (MP3/
WMA), LPCM 44.1 kHz/16 bit/Stereo (WAV)
– Bitrate: within 8 - 320 kbps (MP3), 32 - 192 kbps
(WMA)
1
3
En
ABOUT DISCS AND FILES
■ Disc precautions
WMV file requirement
– WMV9, maximum resolution is 1,920 × 1,080.
About Super Audio CD (SA-CD)
– Audio format based upon the current CD standards but includes a greater amount of information that provides higher quality sound. There are three types of discs: single layer, dual layer and hybrid discs.
The hybrid disc can be played on existing CD players as well as Super Audio CD players since it contains both standard audio CD and Super Audio
CD information.
Super Audio CD disc type
Single layer disc
Dual layer disc Hybrid layer disc
HD layer HD layer CD layer
HD layer
Be careful of scratches and dust
– BD, DVD and CD discs are sensitive to dust, fingerprints and especially scratches. A scratched disc may not be able to be played back. Handle discs with care and store them in a safe place.
Proper disc storage
Place the disc in the center of the disc case and store the case and disc upright.
Avoid storing discs in locations subject to direct sunlight, close to heating appliances or in locations of high humidity.
Do not drop discs or subject them to strong vibrations or impacts.
Avoid storing discs in locations where there are large amounts of dust or moisture.
Hybrid Super Audio CD disc
1
CD layer that plays on any
CD player
High Density layer containing:
2 - High Quality DSD Stereo
3
- High Quality DSD Multi-channel
Hint
– This player supports DSD data transmission via
HDMI using a compatible AV receiver.
Note
– This unit does not show the text data included in the discs on the front panel display.
■ Loading a disc
– Insert the disc with the label face up.
– In case of the disc recorded on both sides, face down the side to play back.
Handling precautions
– If the surface is soiled, wipe gently with a soft, damp (water only) cloth. When wiping discs, always move the cloth from the center hole toward the outer edge.
– Do not use record cleaning sprays, benzene, thinner, static electricity prevention liquids or any other solvent.
– Do not touch the surface.
– Do not stick paper or adhesive labels to the disc.
– If the playing surface of a disc is soiled or scratched, the Player may decide that the disc is incompatible and eject the disc tray, or it may fail to play the disc correctly. Wipe any dirt off the playing surface with a soft cloth.
Cleaning the pick up lens
– Never use commercially available cleaning discs.
The use of these discs can damage the lens.
– Request the nearest service center approved by
Yamaha to clean the lens.
Notes
– Playback may begin automatically, depending on the disc and setting of this Player.
– The menu may be displayed first, depending on the disc.
– The disc load time may vary depending on the disc.
4
En
■ Front panel
CONTROLS AND FUNCTIONS
1 2 3 4
1 p (On/Standby)
3 SA-CD indicator: Lights up when an SA-CD is
loaded and the SA-CD layer (p. 4) is selected.
4 Front panel display
6 (Eject): Opens/closes the disc tray.
7 (Search backward/Skip backward):
Press to skip backward, and press and hold to search backward.
5 6 7 8 9 0 A B
8 (Search forward/Skip forward):
Press to skip forward, and press and hold to search forward.
9 (Play)
0 (Pause)
A (Stop)
B PURE DIRECT: Press to change the Pure Direct
mode (p. 7) to mode 1/mode 2/off. This button lights
up when Pure Direct mode is set to mode 1/mode 2.
Loading the batteries in the remote control
2
3
1
Approximate operating range of remote control
Remote control sensor
30˚ 30˚
6 m (20 ft)
Notes
– Do not subject the remote control unit to shock, water or excessive humidity.
– The remote control unit may not function if the
Player’s remote sensor is in direct sunlight or any other strong light.
– Incorrect use of batteries may cause them to leak or burst. Read the battery warnings and use the batteries properly.
– Do not mix old and new batteries, or mix different brands.
– Remove the batteries if you will not use the remote control unit for an extended period of time.
– Dispose of batteries according to your regional regulations.
5
En
1
CONTROLS AND FUNCTIONS
■ Remote control
Note
– will appear on the top left corner of the screen when the pressed button is not available.
1 Infrared signal transmitter: Outputs infrared signal. Aim this window to the remote control sensor
a specified point of a movie. After Bookmark is set, to select the set point you want to jump to, press
DIGEST. You can set up to 12 Bookmarks.
3 : Opens/closes the disc tray.
4 PROGRAM Sets the order of playback
(p. 24). You can set up to 15 tracks (for an audio disc)
or titles/chapters (DVD-Video).
5 Color buttons BD on-screen instructions.
: Use these buttons according to
6 Number buttons: Enters numbers, or during playback, jumps to the track/chapter corresponding to the number you input. These buttons may not be available depending on the disc type and playback condition.
7 CLEAR: Clears entered number/set item.
8 SETUP: Displays SETUP menu screen (p. 26).
PIP Mark ( ) is displayed on the screen when this function is available. You can also select this item from
Note
– PIP Mark is displayed only when the PIP Mark is set
0 2ND AUDIO BD : Selects the secondary audio of
the Picture in Picture (p. 25) or audio commentaries.
The Secondary Audio Mark ( ) is displayed on the
screen when this function is available (p. 33). You can
also select this item from On Screen menu (p. 22).
Note
– Secondary Audio Mark is displayed only when
Secondary Audio Mark is set to on (p. 30).
6
En
A TOP MENU BD DVD : Displays the top menu
screen (p. 41) if the disc contains a menu. Select the
desired item using 5/a/2/3 and ENTER.
Note
– Specific operations may be different depending on the disc. Follow the instructions of each menu screen.
B Cursor buttons (5/a /2/3): Moves the focus in the menu screen.
ENTER: Selects the focused menu/item.
C RETURN: Returns to the previous menu or screen, etc.
D SUBTITLE :
languages (p. 41) if available . You can also select this
item from On Screen menu (p. 22).
E STATUS: Displays the playback information (p. 23).
F Control buttons
BD DVD CD VIDEO MUSIC PHOTO
/ : Searches backward/forward. The search speed will change each time you press the button
(search backward/forward: 5 steps each). Press to resume normal playback.
/ BD DVD CD VIDEO MUSIC :
Press and hold for instant search/replay. Instant search skips the content 30 seconds. Instant replay replays the content from 10 seconds before.
/ : Skips backward/forward.
: Stops playback. To stop playback completely, press this button twice.
: Pauses playback.
: Plays back contents.
( )/ ( )
BD DVD : Performs slow backward/forward. Slow playback speed will change each time you press the button (slow backward/forward: 4 steps each).
These buttons also perform frame advance/reverse playback during pause.
Press to resume normal playback.
Many DVD-Audio discs include slide show and page turn capabilities. Press / to move to a previous/ next page. This function is only for DVD-Audio.
Notes
– Some BD/DVD discs are not compatible with frame advance/reverse playback.
– Depending on the disc, this Player resumes playback from the point that where the Player was previously stopped. To play back from the beginning, press and then .
CONTROLS AND FUNCTIONS
G SA-CD/CD: Switches the playback layer of a hybrid
SA-CD between SA-CD and CD (p. 4).
1
Hint
– The SA-CD/CD indicator (p. 5) on the front panel
lights up when an SA-CD is loaded and the SA-CD
Notes
– Audio signals are only output from the AUDIO OUT
jacks (p. 11) while the SA-CD layer is selected.
– Audio signals recorded in DSD multi-channel format cannot be played on this Player.
H PURE DIRECT: Changes Pure Direct mode. Pure
Direct mode shown below will change each time you press the button. Pure Direct mode improves audio quality. PURE DIRECT on the front panel lights up when Pure Direct mode is set to mode 1/mode 2.
Mode 1: Front panel display is turned off, and video signals are not output. This mode is suitable listening audio.
Mode 2: Front panel display is turned off, and video signals from other than HDMI terminal are not output.
This mode is suitable for watching movies with high quality sound.
off: Normal play back.
I DIMMER: Changes brightness of the front panel display in 5 steps.
PHOTO
When thumbnails are displayed, you can proceed to the next/previous page with / .
DVD VIDEO
K p: Turns this Player on or sets it to the standby mode.
L ZOOM :
The size of the screen will change each time you press the button (zoom in/out: 3 steps each).
Continued to the next page.
\
7
En
CONTROLS AND FUNCTIONS
M SEARCH :
Jumps to a specified point during playback. For details
on this function, refer to “Using search” (p. 24). You
can also select this item from status menu (p. 23).
N HOME: Displays the HOME menu screen (p. 19).
O REPEAT :
Changes repeat mode. Repeat mode shown below will change each time you press the button.
: Repeats the title being played back.
: Repeats the chapter being played back.
: Repeats all tracks/files on the disc/folder.
: Repeats the track/file being played back.
P A/B : a specific part you want to repeat.
1 Press A/B at the scene where you want to set the start point. “A-” is displayed on the screen.
2 Press A/B again at the scene where you want to set the end point. “A-B” is displayed on the screen.
Repeat playback starts.
3 To cancel the repeat playback, press A/B. “A-B” disappears and the repeat playback is finished.
Note
– This function cannot be performed depending on the specifications of the disc.
menu. The menu contents displayed vary depending on the disc. For details on how to see and operate the pop-up menu, refer to the manual for the disc.
The top menu screen may be displayed by pressing
POP-UP/MENU depending on the DVD.
R ON SCREEN: Displays On Screen menu (p. 22).
BD DVD video is recorded with multiple angles. The Angle
Mark ( ) is displayed on the screen when this function is available. You can also select this item
Note
– Angle Mark is displayed only when the Angle Mark
BD DVD format. You can also select this item from On Screen
8
En
ID function
You can change the remote control ID to prevent unwanted operation of the other Yamaha player such as
DVD player. If you have changed the remote control ID, make sure that you select the same ID for the main unit.
The default setting is ID1.
1 Remote control setting
To change the ID from ID1 to ID2, press and hold the red color button and 2 of number button simultaneously for 3 seconds. To change the ID from ID2 to ID1, press and hold the red color button and 1 of number button simultaneously for 3 seconds.
2 Main unit setting
Press and hold and on the front panel simultaneously for 2 seconds to display current ID when:
– No disc is inserted in this Player.
– The disc tray is closed.
– Playback is stopped.
– “NO DISC” is displayed on the front panel display.
Keep pressing and holding the keys for another 2 seconds to change the ID between ID1 and ID2.
Note
– If the remote control is without batteries for a few minutes or if exhausted batteries remain in the remote control, the remote control ID is automatically set to ID1. If you want to use the remote control in ID2 setting, install new batteries and set the remote control ID again.
CONTROLS AND FUNCTIONS
1
9
En
CONNECTION
INTRODUCTION TO CONNECTIONS
Find the corresponding connection method on your video/audio equipment. We recommend that you use the HDMI terminal which provides high quality digital audio and video on a single connection. If you use the other terminals/jacks, connect the video first. Then connect the audio.
HDMI terminal on
AV receiver? *
HDMI terminal on TV?
Connect video and audio to AV receiver with HDMI cable.
Refer to owner’s manual of AV receiver.
START
Use AV receiver?
HDMI terminal on TV?
Connect video to TV with HDMI cable.
Connect video to AV receiver.
HDMI terminal on TV?
Connect video and audio to TV with HDMI cable.
Yes
No
■ Rear panel
Connect video to TV.
* When you connect to an AV receiver that cannot output the sound input via its HDMI terminal, refer to the owner’s manual of your AV receiver.
10
En
1 2 3 4 5 6 7 8 9 0 A
Video connection to TV
A’
to AV receiver
B
or
C
Video connection to TV
B’
or
C’
Connect audio to AV receiver.
Connect audio to TV.
Video and audio connection to
AV receiver
A
Audio connection to AV receiver
D
or
E
or
F
or
G
Video and audio connection to TV
A’
Audio connection to TV
D’
or
E’
or
F’
2
4 REMOTE CONTROL (IN/OUT/RS-232C) (p. 17)
5 7.1 ch surround (AUDIO OUT) (p. 15)
6 MIXED 2CH (AUDIO OUT) (p. 15)
11
En
HDMI CONNECTION
■ Connecting to the HDMI terminal
– You can enjoy high quality digital picture and sound through the HDMI terminal.
– Firmly connect an HDMI cable (commercially available) to the HDMI terminals.
– See page 34 for information on the audio/video output formats.
– Use HIGH SPEED HDMI cables that have the HDMI logo (as shown on the back cover).
Caution!
Do not connect the power cable of this Player until all connections are completed.
This Player
Hints
– When you use the HDMI Control function,
refer to the “HDMI Control” (p. 29).
– For information on the output mode of HDMI
terminal, refer to the “HDMI” (p. 33).
To HDMI terminal
HDMI cable
(commercially available)
A A’
AV receiver
To HDMI input terminal
HDMI IN
TV
12
En
VIDEO CONNECTIONS
■ Connecting to the component/video jack
– You can enjoy accurate color reproduction and high quality images through the component jacks.
– Firmly connect a component video cable (commercially available) or a video pin cable to the COMPONENT jacks/
VIDEO jack.
– See page 35 for information on the video output formats.
2
Caution!
Do not connect the power cable of this Player until all connections are completed.
This Player This Player
To COMPONENT jacks
B
Component video cable
(commercially available)
B’
To component input jacks
C
Video pin cable
(supplied)
(Yellow)
To VIDEO jack
To video input jack
COMPONENT IN
P
R
(Red)
P
B
(Blue)
(Green)
Y
(Yellow)
VIDEO
AV INPUT
AV receiver TV AV receiver
Note
– If you play back the image via VCR, the image may deteriorate due to the copy guard function.
TV
C’
13
En
AUDIO CONNECTIONS
■ Connecting to the digital audio jack/terminal
– You can connect audio equipment or the TV to the COAXIAL jack/OPTICAL terminal.
– Firmly connect a Coaxial digital audio cable (commercially available) or optical cable (commercially available) to the coaxial digital audio jack or optical digital audio terminal.
– See page 34 for information on the audio output formats.
Caution!
Do not connect the power cable of this Player until all connections are completed.
This Player This Player
To COAXIAL jack
To OPTICAL terminal
D
To coaxial input jack
Coaxial digital audio cable
(commercially available)
E
Optical cable
(commercially available)
E’
To optical input terminal
COAXIAL
AV INPUT
OPTICAL
DIGITAL AUDIO IN
AV receiver TV AV receiver TV
Hint
14
En
AUDIO CONNECTIONS
■ Connecting to the audio jacks
– You can connect audio equipment or the TV to the MIXED 2CH/7.1 ch surround jacks.
– Firmly connect audio pin cables (supplied and commercially available) to the MIXED 2CH jacks or 7.1 ch surround jacks.
– See page 34 for information on the audio output formats.
– If you want to reproduce multi-channel SA-CD and DVD-Audio, connect 7.1 ch surround jacks to the corresponding input jacks of your AV receiver using commercially available audio pin cables.
2
Caution!
Do not connect the power cable of this Player until all connections are completed.
This Player This Player
G
To AUDIO OUT
MIXED 2CH jacks
F
Audio pin cable
(supplied)
F’
To audio input jacks
(White) (Red)
AUDIO
L R
AUDIO IN
To 7.1 ch surround jacks
Audio pin cables
(supplied and commercially available)
To
MULTI
CH IN jacks
CENTER SUBWOOFER SURROUND BACK SURROUND FRONT
L R
(White) (Red)
MULTICH IN
L R L R
(White) (Red) (White) (Red)
AV receiver TV AV receiver
Hints
– You can connect a subwoofer to the SUBWOOFER jack directly. When you connect TV to this Player directly, connect an active subwoofer such as Yamaha Active Servo Processing Subwoofer System to this jack.
15
En
NETWORK AND USB CONNECTION
■ Connecting to the NETWORK terminal and USB port
– PC contents can be played back by connecting this Player to the network.
– You can enjoy a variety of contents with interactive functions by connecting to the internet when playing BD-Live
compatible discs. Refer to page 25 regarding further information on BD-Live functions.
– You can connect a USB memory device (2 GB or greater and formatted with FAT 32/16) for BD Local Storage to the USB port on the rear panel (or front panel) of the player to save the BD-Live data or to upgrade the software of
– Firmly connect a network cable (commercially available) and a USB memory device (commercially available) to the NETWORK terminal and USB port.
– Use only an STP (shielded twisted pair) network cable.
– When using the internet, a broadband internet connection as shown below is required.
– Connect the other connector of the network cable to the hub/broadband router.
Before using the USB memory device
This Player
CAUTION:
– Do not remove the USB memory device or unplug the power cable while the
operations for Local Storage (p. 29) or
software upgrade are being performed.
– Do not use a USB extension cable when connecting a USB memory device to the
USB port of the Player. Using a USB extension cable may prevent the Player from performing correctly.
Note
– Yamaha cannot guarantee that all brands’
USB memory devices will operate with this Player.
To NETWORK terminal To USB port
Network cable
(commercially available)
USB memory device
(commercially available)
Notes
– When using a broadband internet connection, a contract with an internet service provider is required. For more details, contact your nearest internet service provider.
– Refer to the operation manual of the equipment you have as the connected equipment and connection method may differ depending on your internet environment.
– Use a network cable/router supporting
10BASE-T/100BASE-TX.
To LAN terminal
LAN
Internet Modem Hub or broadband router
After connecting
– When you set the Network setting manually, refer to “Network” (p. 31).
– To play back the PC contents on your network, refer to “Using network content” (p. 21).
PC
16
En
OTHER CONNECTIONS
■ Connecting to the REMOTE
CONTROL jacks
– You can transmit and receive the remote control signals by connecting to the REMOTE CONTROL
(OUT/IN) jacks.
– Firmly connect monaural 3.5 mm mini plug cables
(commercially available) to the REMOTE
CONTROL (OUT/IN) jacks.
– If your AV receiver is a Yamaha product and has the capability to transmit SCENE control signals, you can control the Player with the SCENE function.
– You can connect a Yamaha component (such as CD player) supports the SCENE function to the
REMOTE CONTROL (OUT) jack of this Player.
– The RS-232C terminal is a control expansion terminal for commercial use. Consult your dealer for details.
■ Connecting the power cable
– After all connections are completed, plug the supplied power cable into the AC IN on the rear of the Player. Then plug into AC outlet.
2
Caution!
Do not connect the power cable of this
Player until all connections are completed.
This Player
To AC IN
To REMOTE
CONTROL
(OUT) jack
Monaural 3.5 mm mini plug cable
(commercially available)
To remote control in jack
REMOTE CONTROL IN
To REMOTE
CONTROL (IN) jack
Monaural 3.5 mm mini plug cable
(commercially available)
To remote control out jack
REMOTE CONTROL OUT
To AC outlet
Note
– TO PREVENT RISK OF ELECTRIC SHOCK, DO
NOT TOUCH THE UN-INSULATED PARTS OF
ANY CABLES WHILE THE POWER CABLE IS
CONNECTED.
Yamaha component Infrared signal receiver or Yamaha component
(such as AV receiver)
Hints
– For details about the SCENE function, refer to the owner’s manual supplied with your Yamaha AV receiver.
17
En
PLAYBACK
INITIAL WIZARD/EASY SETUP
■ Setting with the Initial Wizard/
Easy Setup
Initial Wizard/Easy Setup allows you to set language, resolution, and screen aspect ratio easily. Initial Wizard screen is displayed when you turn this Player on for the first time after purchase or upgrade. Same setting can be performed from SETUP menu = System = Easy Setup.
1 When Easy Setup screen is displayed, Press ENTER to start Easy Setup.
4 Press 5/a to select the screen aspect ratio, then press
ENTER. For details on setting items, see “TV Screen”
Easy Setup is completed.
2 Press 5/a to select the language you want to display on the screen, then press ENTER.
Note
– When no picture is displayed after Initial Wizard/
Easy Setup is completed, refer to
3 Press 5/a to select the resolution, then press ENTER.
For details on setting items, see “Resolution” (p. 31).
18
En
HOME/MEDIA MENU
HOME and MEDIA menus allow you to browse and play multi-media files on data discs, USB memory devices and your network.
Note
– For details on playable disc and format, see page 3.
■ Playing back photo/music/video
Common operations for playing back files in a selected folder
Example: Selecting a movie file on a USB memory device
Note
– Stop the playback of the video before you move to
MEDIA menu screen.
1 Press HOME to move to HOME menu screen.
Press 2/3 to select MEDIA, then press ENTER.
Basic operation
5/a: Moves the focus.
2: Returns to the parent folder.
3: Checks/unchecks single folder/file.
HOME: Moves to/exits HOME menu screen.
ENTER: Confirms the folder/file.
POP-UP/MENU: Opens Edit Menu.
HOME
2ND
AUDIO
TOP MENU
A/B
POP-UP/MENU
3
RETURN
ENTER
ON SCREEN
Icons on the top of MEDIA menu
: Plays back the disc on the tray, or displays contents in the data disc.
: Displays contents in the USB memory device connected to the USB port.
: Searches for a DLNA (p. 21) server on the network.
: Displays contents on the connected DLNA server.
2 MEDIA screen appears.
3 Select the item which contains the file you want to play back, then press ENTER.
19
En
HOME/MEDIA MENU
4 Select the Photo, Music, Video or AVCHD folder you want to play back, then press ENTER.
To return to the parent folder, press 2 or select .
Note
– Note that the only the file type selected on this step will be displayed in the following step. For example, if you selected Photo folder in this step, only photo files are displayed after this step. When you play back other than photo, return to this hierarchy and select file type again.
5 Select the folder(s) containing the file you want to play back.
Hint
– To enjoy slide show with music, press HOME to return to the HOME menu screen while music is played back, and select photo file.
Note
– The displayed file may not be played back depending on the content.
Operations for viewing photos
While viewing photos, the buttons on the remote control work as shown below.
: Stops slide show and returns to the file browser.
: Pauses a slide show.
: Plays a slide show.
: Moves to a next photo.
: Moves to a previous photo.
: Makes a slide show faster in 3 steps.
: Makes a slide show slower in 3 steps.
5: Inverts a photo.
a: Reflects a photo.
2: Rotates a photo counterclockwise.
3: Rotates a photo clockwise.
ZOOM: Zooms in/out a photo (zoom in/out: 3 steps each).
5/a/2/3: Pan in zoom mode when a photo is larger than the screen.
DIGEST: Switches to thumbnail mode (p. 7). When
thumbnails are displayed, you can proceed to the next/ previous page with / .
6 Select the file you want to play back, then press
ENTER.
When a video file is selected, playback starts.
When a music file is selected, status screen is displayed and playback starts.
When a photo file is selected, slide show starts.
20
En
■ Using network content
This Player is a DLNA certified digital media player. You can manage photo, music and video contents stored on
DLNA servers on your home network.
About DLNA
DLNA (Digital Living Network Alliance) provides easy sharing of digital media through network in the home, and you can enjoy digital contents stored on your DLNAserver-software-installed PC or other DLNA compatible device with your TV via this Player. To connect this
Player to your DLNA servers, some settings for the
DLNA server or device are required. For details, refer to your DLNA server software or DLNA device.
Playing back shared contents
1 To play back files on your PC, install a DLNA server software, such as Windows Media Player 12, and share files you want to play back.
2 Turn on the PC with DLNA server software installed or the DLNA device connected to your home network.
3 Press HOME to display HOME menu screen. Then select MEDIA to move to MEDIA menu. The DLNA servers connected to the network are listed on the screen.
Notes
– If your DLNA server is not listed, select DLNA
Search to find it.
– Depending on the DLNA server, this Player may need to be permitted from the server.
– To play the file on the DLNA server, this Player and the server must be connected to the same access point.
– The file requirements may not always be compatible.
There may be some restrictions depending on file features and DLNA sever capability.
4 Select the file you want to play back.
Notes
– The playback and operating quality may be affected by your home network condition.
– The files from removable media such as USB memory devices or DVD-drive on your media server, may not be shared properly.
HOME/MEDIA MENU
3
21
En
ADVANCED PLAYBACK OPERATION
This chapter explains playback of commercially available
BD and DVD discs, SA-CDs, CDs, and recorded DVD-
RW/R discs.
Note
– For the basic playback operation, see page 6.
■ On Screen menu
To display On Screen menu, press ON SCREEN. After that, press 5/a/2/3 to select an item, then press
ENTER to operate the desired function.
Hint
– When a DVD-Video is played back, you can select
Random All, Random TT (title), Random CH
(chapter), Shuffle All, Shuffle TT (title) and Shuffle
CH (chapter).
Audio : Shows audio language/ signal of BD/DVD disc currently selected. You can select the desired type of audio.
On Screen menu contains following items.
Title : Shows the title number being played back. You can skip to the desired title by selecting it from this item.
Chapter : Shows the chapter number being played back. You can skip to the desired chapter by selecting it from this item.
Track/File : Shows track/file number being played back. You can skip to the desired track/file by selecting it from this item.
Time : Shows the playback time. Select display type from the following:
– Elapsed playback time of the title, chapter, disc, track or file
– Remaining playback time of the title, chapter, disc, track or file
Mode/Play Mode
DVD CD VIDEO MUSIC PHOTO : Shows current playback mode. You can select playback mode from the following:
– Normal: Normal playback.
– Shuffle: Each track/file must play once without repetition.
– Random: Real random playback. Repetition may happen.
number. If the video is recorded with multiple angles, you can change the angle.
Subtitle : Shows the currentlyselected subtitle language when the subtitle is provided.
Subtitle Style BD : Shows the currently-selected subtitle style. This function is available only for Video-file external subtitle. You can select the desired text style of subtitle.
Bitrate : Shows bitrate of the audio/video signal.
Second Video BD
: Turns the PIP on/off (p. 6).
Second Audio
BD : Turns the secondary audio on/off
Ins Search
BD DVD CD VIDEO MUSIC : Skips 30 seconds.
Ins Replay
BD DVD CD VIDEO MUSIC from 10 seconds before.
: Replays the content
Slide Show PHOTO :
Shows slide show speed. You can select the slide show speed from Slow/Medium/Fast.
screen. You can select the transition type.
Code Page VIDEO : Selects character code of subtitle
you added to DivX video (p. 40).
22
En
ADVANCED PLAYBACK OPERATION
■ Status menu
This shows various settings, such as subtitles, angle settings and the title/chapter/track number currently played back. To display status menu, press STATUS.
Status menu contains following menus.
When playing BD-Video/DVD-Video or video file
Example: Icons when playing BD
1 2 3 4 5
When playing audio disc or music file
Example: Icons when playing music file
3
8 7 6
1
2
3
(Playback status)
(Repeat mode): Shows current repeat mode (p. 8).
(Disc type/music file icon)
1 (Playback status)
2 (Disc type/video file icon)
3 (Title number being played): You can jump to
specified title with SEARCH button (p. 8).
4 (Chapter number being played): You can
jump to specified chapter with SEARCH button (p. 8).
5 (Elapsed playback time): You can jump to
specified point with SEARCH button (p. 8).
6 (Subtitle currently selected): You can change the subtitle language with SUBTITLE button.
7 (Audio currently selected): You can change the audio language or format with AUDIO button.
8
(Repeat mode): Shows current repeat mode (p. 8).
contains it.
5 (Track/file number being played): You can
jump to specified track with SEARCH button (p. 8).
if the file contains them.
7 (Elapsed playback time): You can jump to
specified point with SEARCH button (p. 8).
8 (Progress bar) MUSIC current song.
: Shows progress status of
9 (Audio level meter): displays current volume level.
When viewing photo
1
2
(Playback status)
(Photo file icon)
3 (File number being displayed)
4
(Repeat mode): Shows current repeat mode (p. 8).
5 (Slide show speed)
23
En
ADVANCED PLAYBACK OPERATION
■ Using Bookmark
DVD VIDEO
This allows you to set Bookmark at the specified point of the video. After Bookmark is set, you can move to the point you set using this function. You can set up to 12
Bookmarks.
1 Press MARKER during playing back the movie to set
Bookmark. Bookmark number, and the status are displayed.
2 Press ENTER to program playback order.
For audio disc, press 5/a to select a desired track then press ENTER.
For DVD-Video disc, select a desired title (shown as
TT) and chapter (shown as CH) instead of a track.
To clear a set track, select the track you want to clear, then press CLEAR.
Press RETURN to cancel the Program play.
2 After Bookmark is set, press DIGEST to display
Bookmark select bar.
3 Press 2/3 to select the Bookmark you want to play back, then press ENTER.
Press CLEAR to delete the selected Bookmark.
Note
– When playback is finished (e.g., ejecting the disc, pressing twice), Bookmarks are automatically deleted.
■ Program play
DVD CD
This allows you to program playback order of audio disc tracks or DVD chapters.
Press PROGRAM during playback to display the
PROGRAM window to program playback order.
You can program up to 15 tracks/chapters.
Example: Programming the playback order of CD tracks
1 Press PROGRAM during playback.
3 After programming is finished, press to set and start program playback.
4 To cancel program play, stop playback completely by
■ Using search
BD DVD CD VIDEO MUSIC
This allows you to jump to the specified point during playback.
1 Press SEARCH during playback. Status bar appears.
2 Press 5/a /2/3 to select one of the item below, then press ENTER.
BD DVD :
– Title number (shown as )
– Chapter number (shown as )
– Elapsed title time (shown as )
– Elapsed chapter time (shown as
CD :
– Track number (shown as )
– Elapsed track time (shown as )
)
– Elapsed disc time (shown as
VIDEO MUSIC :
)
– File number (shown as )
– Elapsed file time (shown as )
3 Press 5/a or number buttons to set/adjust the value of the focused item, and press ENTER to jump to the specified point.
4 To close the status bar, press STATUS.
24
En
■ Enjoying BONUSVIEW and BD-
Live
This player supports BONUSVIEW (p. 40) (BD-ROM
Profile 1 Version 1.1) and BD-Live (p. 40) (BD-ROM
Profile 2) playback functions.
Note
– Functions and playback method vary depending on the disc. See the guidance on the disc or the supplied user’s manual.
■ Using Picture in Picture function
(secondary audio/video playback)
BD-Video that includes secondary audio and video compatible with Picture in Picture can be played back with secondary audio and video simultaneously as a small video in the corner.
Primary video Secondary video
ADVANCED PLAYBACK OPERATION
■ Using the feature of BD-Live
1.
Set the Network setting (p. 31).
2.
Connect the USB memory device
to this Player (p. 16).
BD-Live data is saved in Local Storage (p. 29) (USB
memory device connected to this Player). To enjoy these functions, connect a USB memory device
(2 GB or greater and formatted with FAT 32/16) supporting USB 2.0 High Speed (480 Mbit/s) to the
– BUDA folder is created automatically in the USB memory device when necessary.
– If there is insufficient storage space, the data will not be copied/downloaded. Delete unneeded data or use a new USB memory device.
– Some time may be required for the data to load
(read/write).
3
Notes
– Yamaha cannot guarantee that all brands’ USB memory devices will operate with this Player.
– Do not use a USB extension cable when connecting a USB memory device to the USB port of the player.
Using a USB extension cable may prevent the player from performing correctly.
3.
Play back the disc.
While PIP Mark ( ) or Secondary
Audio Mark ( ) is displayed, press
PIP to turn the Picture in Picture function on/off.
Notes
– To listen to secondary audio, make sure that the
Audio Output setting (Coaxial/Optical or HDMI) is
set to PCM or Reencode (p. 33).
– Depending on the disc, to listen to secondary audio, you may need to set secondary audio to on on the top
– The secondary audio and video for Picture in Picture may automatically play back and be removed depending on the content. Also, playable areas may be restricted.
4.
Run BD-Live according to the instructions on the disc.
Notes
– Regarding playback method of BD-Live contents, etc., perform the operations in accordance with the instructions in the BD disc manual.
– To enjoy BD-Live functions, perform the network
connection (p. 16) and Network settings (p. 31).
– Refer to “BD-Live Connection” (p. 31) regarding the
setup to restrict access to BD-Live contents.
– The time required to download the provided programs into the USB memory device connected to this Player varies depending on the internet connection speeds and the data volume of the programs.
– BD-Live programs provided through the internet may not be able to display the connection depending on the status (upgrading) of the provider. In such cases, take out the disc and try again.
– If the BD-Live screen does not appear for a while after you select the BD-Live function in the BD disc menu, the USB memory device may not have enough free space. In such cases, eject the disc from the player, and then erase the data in the USB memory device using the “Format” menu in the
25
En
SETTINGS
SETUP MENU
The SETUP menu enables various audio/visual settings and adjustments for functions using the remote control unit.
Menu/Submenu
System
General Setting
Language
Playback
Security
Network
Item
Screen Saver Sets screen saver on/off.
Function
Disc Auto Playback Sets this Player to start disc playback automatically.
HDMI Control Sets this Player to receive control signal from the remote control of your TV/AV receiver.
Network Control
Load Default
Sets the control via Ethernet to on/off.
Resets all settings to the default setting except Security setting.
Performs upgrade of this Player.
Upgrade
Easy Setup
Local Storage
OSD
Menu
Audio
Subtitle
Closed Caption
Angle Mark
PIP Mark
Sets language, resolution, screen aspect ratio.
Displays status of Local Storage (p. 29), formats Local
Storage and selects the front/rear USB port for Local Storage.
Selects the language for On Screen Display.
Prioritizes the language for disc menu.
Prioritizes the language for audio.
Prioritizes the language for subtitle.
Sets the closed caption to on/off.
Sets to display the Angle Mark when BD/DVD with multiple angles is played back.
Sets to display the PIP Mark when BD/DVD with Picture in
Picture is played back.
Secondary Audio
Mark
DivX(R) VOD
DRM
DVD-Audio Mode
Sets to display the Secondary Audio Mark when BD/DVD with secondary audio is played back.
Displays registration code for DivX(R) video.
Change Password
Parental Control
Country Code
Sets DVD-Audio mode to DVD-Audio/DVD-Video.
Changes password for Parental Control and Country Code.
Sets the Parental Control depending on the disc content.
Sets your Country Code.
Internet Connection Sets the internet connection to Enable/Disable.
Information Displays network information screen.
Connection Test
IP Setting
BD-Live
Connection
DLNA
Proxy Setting
Performs the network connection test.
Sets the IP setting to Auto/Manual.
Sets the BD-Live connection to Permitted/Partial Permitted/
Prohibited.
Sets the DLNA to Enable/Disable.
Sets the proxy setting.
Page
26
En
Menu/Submenu
TV
Display Setting
Audio Setting
Video Process
Audio Output
SACD Output
Speaker Setting
Post Process
SETUP MENU
Item
TV Screen
Resolution
TV System
Color Space
Function
Sets the screen aspect ratio of the connected TV, and adjust the video output.
Selects the resolution of output video.
Selects the TV System from NTSC/PAL/Multi.
Selects Color Space from RGB/YCbCr 4:4:4/YCbCr 4:2:2/
Full RGB.
HDMI Deep Color Selects HDMI Deep Color from 30 bits/36 bits/Off.
HDMI 1080p 24Hz Sets HDMI 1080p 24Hz to auto/off.
Lip Sync Adjusts the lag between video and audio, such as when the mouth movement is out of sync with the voice.
Video Mode
Color Adjust
Adjusts the visual image.
Adjusts Brightness/Saturation/Hue for each color.
Auto Contrast
Noise Reduction
De-interlacing
Mode
Coaxial/Optical
Adjusts contrast to optimize the played back image.
Sets the level of Noise Reduction.
Sets how to detect the video signal.
HDMI
Downsampling
DRC
SACD Priority
HDMI Output
Configuration
2ch Downmix
Selects the output mode of COAXIAL jack/OPTICAL terminal from Bitstream/PCM/Reencode/Off.
Selects the output mode of HDMI terminal from Bitstream/
PCM/Reencode/Off.
Selects the digital audio signal down sampling frequency from 48k/96k/192k.
Sets the DRC (Dynamic Range Compression).
Selects a contents when Hybrid SA-CD is played back.
Selects the output mode of HDMI terminal from DSD/PCM when SA-CD is played back.
Sets the audio output of 7.1 ch surround jack.
Selects down mix method to analog 2-ch.
Multi-channelizes the 2-channel audio signal.
Displays software version and MAC address (p. 41).
Page
4
System
Information
27
En
SETUP MENU
■ Example of SETUP menu
operation
You need to call up the SETUP menu screen to perform settings for this Player. The following is the explanation for basic operations of the SETUP menu.
3.
Select a menu item.
Press 5/a to select Parental Control, then press
ENTER or cursor 3.
CLEAR
PIP
TOP MENU
SEARCH
SETUP
HOME
REPEAT
POP-UP/MENU
ENTER
RETURN ON SCREEN
Example: Setting Parental Control
Note
– Some items cannot be set during playback. In this case, press twice to stop playback completely before setting.
1.
Display the SETUP menu screen.
Press SETUP to display the SETUP menu screen.
Press 2/3 to select General Setting, then press
ENTER or a .
4.
Enter password.
Enter your password with number buttons.
– The default password is 0000.
– You cannot move to the next setting screen until you have input the correct password.
– To change the password, refer to “Change
5.
Select a next item.
Press 5/a to select the Parental Control Level for
BD/DVD, then press ENTER.
2.
Select a Submenu.
Press 5/a to select Security, then press ENTER or cursor 3.
6.
Exit the menu screen.
Press 2 to return to the previous menu.
28
En
■ General Setting
The default settings are marked with “ * ”.
System
Screen Saver
You can set the screen saver to on/off.
When set to on, this Player will switch to screen saver mode if there is no operation for 3 minutes. After that, this
Player will turn to standby mode when there is no operation for 6 minutes.
On * , Off
Disc Auto Playback
You can set Disc Auto Playback to on/off. When set to on, a disc will play back automatically after loading.
On * , Off
HDMI Control
You can set the Player to receive control signal from a
TV/AV receiver compatible with the HDMI Control
function via an HDMI cable (p. 12).
On, Off *
Using HDMI Control function
Using the HDMI Control function, you can interactively operate this Player with your TV (HDMI Control function supported).
When you connect this Player to the TV compatible with the HDMI Control function using an HDMI cable and
set HDMI Control in the SETUP menu to on (p. 29), you
can perform the function listed below.
• Automatic input select function
When you start playback of this Player, the input selector of the TV (and an AV receiver if this Player is connected to the TV via the AV receiver) is switched to this Player automatically. TV Power is turned on automatically depending on the TV.
• Automatic power off function
When you turn off the TV while this Player is in stop mode and the SETUP menu screen is not displayed, the power of this Player is also turned off automatically.
Notes
– HDMI Control function may not work properly depending on the TV.
– Functions other than ones shown above may work depending on the TV or AV receiver.
– In order to make the HDMI Control function available, set up settings for the HDMI Control function on ALL components (this Player, TV, and AV receiver). Certain operation may also be required.
– Each function may be set independently to activate/deactivate depending on the TV.
– Refer to the operation manuals supplied with the
TV and/or AV receiver for details regarding setup.
SETUP MENU
Network Control
You can set control via Ethernet to on/off. This player employs Yamaha Network Control protocol (YNC).
On, Off *
Notes
– When set to on, power consumption during standby mode increases due to network control function.
– When set to on, the system startup time is increased.
Load Default
You can reset all settings of this Player to default setting
except Security setting (p. 30). For details on default
Upgrade
You can upgrade the software manually from Disc, USB
Storage or Network. For details on software upgrade, refer
to “SOFTWARE UPGRADE” (p. 36).
Easy Setup
You can perform Easy Setup (p. 18).
Local Storage
You can display Local Storage information, format Local
Storage, and select Front USB/Rear USB to save the BD-
Live data.
To format (empty) the BUDA folder in the USB memory device, select Information and press ENTER when
“Format” is focused on the screen.
Front USB, Rear USB *
Local Storage
It is used as an auxiliary memory when Blu-ray Disc is played back.
4
29
En
SETUP MENU
Language
OSD
You can select the language for On Screen Display which is the messages or menu displayed on the screen such as
SETUP menu.
English * , , , , ,
DVD-Audio Mode
Some DVD-Audio discs contain the DVD-Video content in addition to the DVD-Audio content. You can select
DVD-Audio mode or DVD-Video mode.
DVD-AUDIO * Both DVD-Audio/Video contents are played back.
Only the DVD-Audio content may be played back depending on the disc.
DVD-VIDEO Only the DVD-Video content is played back.
Menu
You can prioritize the language for disc menu.
English * Français Español Deutsch Italiano
Nederlandse , Portuguese, Danish, Svenska , Finnish,
Norwegian, , Korean, Japanese, More
Audio
You can prioritize the audio language for BD/DVD
playback. For details on setting items, see “Menu” (p. 30).
Subtitle
You can prioritize the language for Subtitle.
Français Español Deutsch Italiano
Nederlandse , Portuguese, Danish, Svenska , Finnish,
Norwegian, , Korean, Japanese, More, Off *
Playback
Closed Caption
You can set to display the closed caption (p. 40) when BD/
DVD with closed caption is played back.
On, Off *
Angle Mark
You can set to display the Angle Mark ( ) when BD/
DVD with multiple angles is played back.
On * , Off
PIP Mark
You can set to display the PIP Mark (
picture in picture (p. 25) is played back.
On * , Off
) when BD with
Secondary Audio Mark
You can set to display the Secondary Audio Mark ( when BD with secondary audio is played back.
On * , Off
DivX(R) VOD DRM
You can display registration code for DivX(R) video.
)
Note
– This setting is only available when no disc is loaded.
Security
Change Password
You can set the password for changing the Parental
Control Level and Country Code. Refer to “Parental
Control” (p. 30) and “Country Code” (p. 30).
Note
– The default password is 0000.
Parental Control
In some BD/DVD discs, a control level for disc viewing is set depending on the age of the viewer. You can set the
Parental Control shown on the screen depending on the disc content.
The password (see “Change Password” on p. 30) needs to
be entered before the Parental Control Levels is set.
After you set the Parental Control, when you play back a disc with level higher than current Parental Control Level, or you want to change the Parental Control Level, a dialog box will pop up to ask you to enter the password.
Off*, 1 to 8
Country Code
You can set the Country Code you live in. The password
(see “Change Password” on p. 30) needs to be entered
before the Country Code is set. This setting may be used for rating of Parental Control and disc playback.
30
En
SETUP MENU
Network
Internet Connection
Set this item to Enable when you use BD-Live (p. 25), DLNA
(p. 21) and software upgrade from the network (p. 36).
Enable * , Disable
Information
You can display network information screen. On this screen, you can view the information of Interface
(Ethernet), Address Type, IP Address, Subnet Mask,
Default Gateway, and DNS.
Connection Test
You can perform an internet connection test. If the test is
failed, please check “IP Setting” (p. 31) and perform the
test again.
IP Setting
You can set IP Setting to Auto/Manual. When set to Auto,
IP address is allocated automatically by system. When set to Manual, IP Address, Subnet Mask, Default Gateway and DNS should be set manually.
Auto * , Manual
BD-Live Connection
You can set access restriction to BD-Live contents.
Permitted
Partial
Permitted *
Allows all BD-Live discs to connect the network.
Allows only discs with owner certification.
Prohibited Prohibits all BD-Live discs to connect the network.
DLNA
You can set the DLNA (p. 21) to Enable/Disable. When
you do not use the DLNA function, set to Disable.
Enable * , Disable
Proxy Setting
You can set Proxy Setting. Set to Disable for normal use.
Set to Enable to set the proxy setting.
Enable
Disable *
Enables proxy host and proxy port setting.
Sets proxy server to disable. Select this item when proxy server is not used.
Proxy Host Sets proxy host.
Proxy Port Sets proxy port.
■ Display Setting
The default settings are marked with “ * ”.
TV
TV Screen
You can set the screen aspect ratio of the connected TV, and adjust the video output.
If you switch your TV (i.e. because you have bought a new one) and the screen aspect ratio of the connected TV changes, you will have to change the TV Screen setting.
16:9 Full Select this when this Player is connected to a TV with a 16:9 screen. When a 4:3 aspect ratio video is played back, the video is displayed as shown below.
16:9 Normal * Select this when this Player is connected to a TV with a 16:9 screen. When a 4:3 aspect ratio video is played back, the video is displayed as shown below.
4:3 Pan Scan Select this when this Player is connected to a TV with a 4:3 screen. When a 16:9 aspect ratio video is played back, the video is displayed as shown below.
4:3 Letterbox Select this when this Player is connected to a TV with a 4:3 screen. When a 16:9 aspect ratio video is played back, the video is displayed as shown below.
Original image size
4:3
Original image size
On 16:9 (wide screen) TV
16:9 Full 16:9 Normal
On 4:3 TV
4:3 Pan Scan 4:3 Letterbox
16:9
Resolution
You can select the video output resolution from Auto,
480i/576i, 480p/576p, 720p, 1080i, and 1080p. When set to Auto, resolution is set to the maximum resolution according to the connected TV. For more details on output
formats, refer to “About the video output formats” (p. 35).
Auto * , 480i/576i, 480p/576p, 720p, 1080i, 1080p
4
Note
– To output HD audio (such as Dolby TrueHD or
DTS-HD Master Audio) from HDMI terminal, set
Resolution to Auto or more than 720p.
31
En
SETUP MENU
TV System
You can select TV System from PAL, NTSC and Multi.
Set the same TV System as your TV set. For more details
on output formats, refer to “About the video output formats” (p. 35).
NTSC * , PAL,
Multi
(Korea, Taiwan and Central and South America models)
NTSC, PAL * ,
Multi
(Russia and Asia models)
Color Space
You can select the Color Space (p. 40) output from
HDMI. This function is available when this Player is connected with an HDMI cable.
RGB Outputs video signal at normal signal range.
YCbCr 4:4:4 * Sets Color Space to YCbCr 4:4:4.
YCbCr 4:2:2 Sets Color Space to YCbCr 4:2:2.
Full RGB When RGB is set and white and black on the screen are too faint, select this item. This setting is effective when a connected component supports RGB 0-255 range.
Note
– This function is only available on TVs that support this function.
HDMI Deep Color
When your TV and/or AV receiver is compatible with
Deep Color (p. 40), set this item according to your TV/AV
receiver. This function is available when this Player is connected with an HDMI cable.
30 bits, 36 bits, Off *
HDMI 1080p 24Hz
This outputs the BD-Video encoded in 24Hz frame rate in
HDMI 1080p 24Hz. Smoother video playback may be available with this function. This function is available when your TV/AV receiver support this function, and this
Player is connected with an HDMI cable. For more details
on output formats, refer to “About the video output formats” (p. 35).
Auto * , Off
Note
– This setting is disabled when output resolution is other than 1080p.
Lip Sync
You can set/adjust the Lip Sync (p. 41) function. To adjust
Lip Sync manually, select Manual, then press 2/3 to adjust the figure.
Auto * , Manual, Off
Video Process
Video Mode
You can select Video Mode below.
Standard* The image is most natural and well-balanced. This mode suits for normal use.
Vivid
Cinema
Custom
The image is more vivid and sharp.
The image suits for watching movie in dark room.
You can adjust the visual image manually. Press 5/ a to select the parameter, then press 2/3 to adjust the figure.
Brightness
Adjusts the overall brightness of the image.
Saturation
Adjusts the richness of the color in the projected image.
Hue
Adjusts the tint of the projected image.
Contrast
Adjusts the bright areas (white levels) in the image.
Sharpness
Adjusts the sharpness of objects in the video.
CTI
Smoothes out the edges of color images. Color images are rendered more distinct.
The default settings are 0.
Color Adjust
You can adjust Brightness/Saturation/Hue for each color
(Red/Green/Blue/Yellow/Cyan/Magenta). To use this function, set Video Mode to Custom. For details on the
setting items, see “Video Mode” (p. 32).
The default settings are 0.
Auto Contrast
Adjusts contrast to optimize the played back image.
Off * , On
Noise Reduction
You can set the Noise Reduction to a level of 0 to 3. 0 is off, and 3 is the maximum level.
0 * , 1, 2, 3
De-interlacing Mode
You can select how to detect the video signal. Set to Auto for normal use. When horizontal stripping noise appears on the screen, set this to Film/Video to remove the noise.
Auto * , Film, Video
32
En
■ Audio Setting
The default settings are marked with “ * ”.
Audio Output
Coaxial/Optical
You can select the output mode of COAXIAL jack and
OPTICAL terminal. For more details on output formats,
refer to “About the audio output formats” (p. 34).
Bitstream Outputs digital signal without any processing.
Secondary Audio is not output.
PCM Outputs 2-channel PCM.
Reencode * Outputs Bitstream with Secondary Audio. The audio signal is output in DTS signal.
Off Mutes sound.
HDMI
You can select the output mode of HDMI ternminal. For
details on setting items, see “Coaxial/Optical” (p. 33). For
more details on output formats, refer to “About the audio output formats” (p. 34).
Bitstream * , PCM, Reencode, Off
Note
– To output HD audio (such as Dolby TrueHD or
DTS-HD Master Audio) from HDMI terminal, set
Resolution to Auto or more than 720p (p. 31).
Downsampling
You can select digital audio signal down-sample frequency. This function is effective for the audio signal output from the COAXIAL jack/OPTICAL terminal.
48k *
96k
192k
The highest sampling rate of digital PCM output is
48 kHz.
The highest sampling rate of digital PCM output is
96 kHz.
The highest sampling rate of digital PCM output is
192 kHz.
DRC
You can set the DRC (Dynamic Range Compression)
(p. 40) to on/off/Auto. When set to Auto, DRC is
automatically turned on for a source with DRC information in Dolby TrueHD format. DRC makes the strong sound such as plosive sound lower, and conversations more audible. It is useful when you watch movies in the night.
Off * , On, Auto
SETUP MENU
HDMI Output
You can select audio signal output from HDMI terminal when SA-CD is played back.
DSD *
PCM
Outputs DSD raw signal. When this Player is connected to DSD compatible AV receiver, this item is recommended.
Outputs PCM signal decoded by this Player.
Speaker Setting
Configuration
You can set the output of 7.1 ch surround depending on the connected speaker or amplifier.
1 Press 5/a to select a speaker you want to configure, then press ENTER.
2 Adjust the figures below. Note that some of items are not displayed depend on the selected speaker.
Size When the woofer section of a speaker is 16 cm (6-1/
2 in) or larger, select Large. When smaller than 16 cm (6-1/2 in), select Small.
Trim
Large * , Small
-12 to 0 dB (in 0.5 dB step)
The default setting is 0 dB.
0.5 to 10 m (in 0.5 m step) Delay
The default setting is 3 m.
Disable When selected speaker is not in use, select Yes.
Yes, No *
3 Press RETURN to go back to speaker selection.
2ch Downmix
You can select down mix method to analog 2-ch from
Stereo or Lt/Rt.
Stereo *
Lt/Rt
Changes channel output to stereo, which only delivers sound from the two front speakers.
Select this item if this unit is connected to a Dolby
Pro Logic decoder. Sound from rear speakers is mixed to the 2 ch stereo sound.
Post Process
You can multi-channelize the 2-channel audio signal. To multi-channelize, select NEO6, then select Cinema or
Music mode.
Off * , NEO6
4
■ System Information
Software version and MAC address (p. 41) are displayed.
SACD Output
SACD Priority
You can select a content played back from multi-channel or stereo (2-channel) contents when a Hybrid SA-CD
(p. 4) including both is loaded.
Multi-ch * , 2-ch
33
En
SETUP MENU
■ About the audio output formats
Source format
PCM 2ch
PCM 5.1ch
PCM 7.1ch
HDMI
Bitstream PCM
PCM 2ch
PCM 5.1ch
PCM 7.1ch
Reencode Bitstream
COAXIAL/OPTICAL
Reencode
MIXED 2CH/
7.1 ch surround
PCM
PCM 2ch
PCM 2ch
PCM 2ch
2ch
2ch/5.1ch
2ch/7.1ch
Dolby Digital with SA * or
BCS **
Dolby Digital PCM 5.1ch
Dolby Digital Dolby Digital
Dolby Digital
Plus
Dolby
TrueHD with SA
BCS
BCS
** with SA
**
*
*
or
or
PCM 2ch Dolby Digital
Dolby Digital
Plus
PCM up to
7.1ch
Dolby Digital
Plus
Dolby Digital PCM 2ch Dolby Digital
Dolby Digital
Dolby
TrueHD
Dolby
TrueHD
PCM up to
7.1ch
Dolby Digital
Dolby Digital PCM 2ch Dolby Digital
2ch/5.1ch
2ch/7.1ch
DTS with SA * or
BCS **
DTS
PCM up to
5.1ch
DTS
DTS HD High
Resolution with SA * or
BCS **
DTS-HD
Master Audio with SA
BCS **
* or
DTS HD High
Resolution
PCM up to
7.1ch
DTS HD High
Resolution
DTS
DTS-HD
Master Audio
PCM up to
7.1ch
DTS-HD
Master Audio
DTS
DTS
DTS
DTS
PCM 2ch
PCM 2ch
PCM 2ch
DTS
DTS
DTS
2ch/5.1ch
2ch/7.1ch
* “SA” is a Secondary Audio.
** “BCS” is a button click sound, the sound effect for pop-up menus, etc.
SA-CD output formats
SACD Output settings
SACD Priority HDMI Output
Multi-ch
DSD
PCM
2-ch
DSD
PCM
HDMI
DSD up to 5.1ch
PCM up to 5.1ch
DSD 2ch
PCM 2ch
COAXIAL/OPTICAL
No output
No output
No output
No output
MIXED 2CH/7.1ch surround
2ch/5.1ch
2ch/5.1ch
2ch/2ch
2ch/2ch
Notes
– When Coaxial/Optical or HDMI is set to Bitstream, secondary audio is not output. (p. 33)
– To output HD audio (such as Dolby TrueHD or DTS-HD Master Audio) from HDMI terminal, set Resolution to
Auto or more than 720p (p. 31).
PCM.
34
En
SETUP MENU
■ About the video output formats
When TV System is set to NTSC
Auto 480i/576i 480p/576p
VIDEO
Resolution
HDMI
1080p 24Hz
Playback BD
HDMI
COMPONENT others
Playback commerciallyreleased DVD
Playback BD others
Playback BD others
–
Max
480i
480i
–
480i
480i
480i
–
480p
480p
480i
720p
–
1080i
–
1080p
On Off
720p 60 Hz 1080i 60 Hz
1080p 24 Hz
1080p 60 Hz
1080p 60 Hz
480p
480i
480p
720p 60 Hz 1080i 60 Hz
480i
480p off 1080i 60 Hz
1080i 60 Hz off
480i
480i
4
When TV System is set to PAL
Auto 480i/576i 480p/576p
VIDEO
Resolution
HDMI
1080p 24Hz
Playback BD
HDMI
COMPONENT others
Playback commerciallyreleased DVD
Playback BD others
Playback BD others
–
Max
576i
576i
–
576i
576i
576i
–
576p
576p
576i
720p
–
1080i
–
1080p
On Off
720p 50 Hz 1080i 50 Hz
1080p 24 Hz
1080p 50 Hz
1080p 50 Hz
576p
576i
576p
576i off off
576i
576p
576p
576p
576i
When TV System is set to Multi
When TV System is set to Multi, video signal is output at the same frequency as the source. Refer to the tables above for details on the frequency setting of the TV and resolution of the output video signal.
While a menu screen such as SETUP menu is displayed, video signal is output at the same frequency as the source.
Notes
– “Max” in the table means that resolution is set to the maximum resolution supported by the connected TV.
– HDMI 1080p 24Hz setting is disabled when output resolution is other than 1080p.
– When HDMI 1080p 24Hz setting is on, video signal is output from HDMI during BD playback.
– When commercially-released DVD is played back with component output, maximum resolution is 480p/576p.
– When TV System is set to NTSC and video source is not 60 Hz, the video output signal is converted to 60 Hz.
– When TV System is set to PAL and video source is not 50 Hz, the video output signal is converted to 50 Hz.
35
En
SOFTWARE UPGRADE
Some of the newly released BD discs cannot be played back unless you upgrade this Player software to the latest version. We recommend upgrading the software of this
Player with software upgrade so that this Player is operated based on the latest software.
3 Select the item which contains the upgrade file package from Disc/USB Storage/Network.
To check for the availability of a software upgrade, visit http://download.yamaha.com/downloads/service/top/
?site=europe.yamaha.com&language=en
Hint
– Software upgrade is automatically started after loading the disc which contains upgrade file package.
Note
– Do not remove the disc/USB memory device, set this
Player to standby mode or unplug the power cable/
LAN cable while the software upgrade is being performed.
■ Upgrading the software
3.
The system will search for upgrade file package.
1.
Prepare for the software upgrade.
When you upgrade the software from Disc/USB
Storage:
1 Save the upgrade file package to the appropriate folder on the disc/USB memory device. For more details, refer to the procedure document attached with the upgrade file package.
2 Load the disc or connect the USB memory device.
When the disc is loaded, software upgrade is started automatically. Skip step 2.
When you upgrade the software from Network:
Confirm that this Player is connected to the network.
4.
Press ENTER to start upgrade.
5.
Upgrade is completed. The system will restart.
2.
Select the upgrade method and start upgrade from SETUP menu.
1 Press SETUP to display SETUP menu screen.
2 Select General Setting = System = Upgrade.
36
En
ADDITIONAL INFORMATION
TROUBLESHOOTING
Refer to the table below when this Player does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off this Player, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center.
■ Power
Problem
No power.
The Player power is turned off.
Possible causes and solutions
– Connect the AC power cable properly.
– Press (p) on the front panel to turn on the power.
– The power will be automatically turned off after 10 continuous minutes of inactivity (no playback).
■ Basic operation
Problem
The remote control does not work.
Buttons do not work.
Password is forgotten.
Possible causes and solutions
– Use the remote control within its operating range. (p. 5)
– Replace the batteries. (p. 5)
– Check the ID settings for the main unit and the remote control. (p. 9)
– Press and hold p on the front panel for around 5 seconds to restart this Player.
– To completely reset this Player, unplug the power cable from the AC outlet for 5 - 10 seconds, plug the power cable to the AC outlet again, and then turn on this Player.
– Press and hold and on the front panel simultaneously when no disc is inserted
and playback is stooped to set the Player to default setting (Security setting (p. 30) is
also reset).
■ Disc playback
Problem
The Player cannot play a disc.
Video stops.
The Player makes a snapping sound when starting playback or loading a disc.
Possible causes and solutions
– Take out the disc and clean it. (p. 4)
– Make sure that the disc is loaded properly (aligned in disc tray and label-side up). (p. 4)
– Use a disc supported by the Player. (p. 3)
– Remove the disc and then check whether the Player supports the disc or not. (p. 3)
– Check the region code. (p. 3)
– Check whether the disc is defective by trying another disc.
– The CD-R/RW, DVD+R/RW/R DL, and DVD-R/RW/R DL must be finalized. (p. 3)
– The Player will stop if it senses shock or vibration.
– These sounds are not malfunctions of the Player but are normal operating conditions.
5
37
En
TROUBLESHOOTING
■ Picture
No picture.
Problem
Screen freezes and operation buttons do not work.
Video is not output with the desired resolution.
Widescreen video appears vertically stretched, or black bands appear at the top and bottom of the screen. Or 4:3 video appears horizontally stretched.
Square noise (mosaic) appears on the screen.
The playback screen will be disturbed if
DVD video is recorded to a VCR, or played back through a VCR.
Audio is not output, or images are not played back properly.
■ Sound
Problem
No sound, or sound is distorted.
Possible causes and solutions
– Make sure that the cables are connected correctly. (p. 10)
– Make sure that the connected TV or the AV receiver is set to the correct input. (p. 10)
– Connect this Player to the TV with VIDEO jack (p. 13) using the supplied video pin
cable and set Resolution properly. (p. 31)
– TV System is set to the incorrect setting. Press and hold DIMMER on the remote control to reset TV System setting to default setting.
– Press , then restart playback.
– Turn off the power and turn on the power again.
– Press and hold p on the front panel for around 5 seconds to restart this Player.
– Set to the desired resolution. (p. 31)
– Change the aspect ratio of your TV. (p. 31)
– Blocks in images may be visible in scenes with rapid movement due to the characteristics of digital image compression technology.
– This Player complies with analog copy protection. Some discs contain a copy prohibiting signal. If you try to play back such discs through a VCR, or record to a VCR and play back the signal, the copy protection will prevent normal playback.
– The audio may not be output or the images may not be played back properly for some discs in which copyright-protected contents are recorded.
Possible causes and solutions
– Turn the volume up.
– There is no sound during still mode, slow motion playback, fast forward and fast
– Check that the audio cable is connected correctly. (p. 10)
– Audio may not be output depending on the audio recording status, such as when audio
other than an audio signal or non-standard audio is recorded for the audio content. (p. 3)
– Check the audio connection. (p. 10)
Left and right channels of audio are reversed, or sound comes out of only one side.
Audio is not output, or images are not played back properly.
Cannot hear the desired audio type and/ or number of channels.
Cannot hear the sound of PIP
(secondary audio).
– The audio may not be output or the images may not be played back properly for some discs in which copyright-protected contents are recorded.
– Refer to Audio Output setting and “About the audio output formats”. (p. 33, 34)
– Set Coaxial/Optical or HDMI to PCM/Reencode. (p. 33)
– To hear secondary audio, press 2ND AUDIO. (p. 6)
– Depending on the disc, you may need to set secondary audio to on on the top menu of
38
En
TROUBLESHOOTING
■ Network
Problem
Cannot connect to the Internet.
Cannot download BD-Live contents.
Cannot detect the DLNA server.
Cannot a play the file on the home network server.
Possible causes and solutions
– Connect the Network cable properly.
– Turn on the connected equipment, such as broadband router or modem.
– Connect the broadband router and/or modem properly.
– Set the proper value(s) in the network setting. Check “Network”. (p. 31)
– Connect the Network cable properly. (p. 16)
– Connect USB memory device properly. Check that the USB memory device is
connected to the USB port of this Player. (p. 16)
– Check if the BD disc supports BD-Live.
– Check the setting for “Internet Connection”. (p. 31)
– Connect the USB memory device formatted in FAT16 or FAT32.
– It is recommended to connect the USB memory device with at least 2 GB of free space.
If there is not enough free space, format the USB memory device. (p. 29)
– Connect the network cable properly.
– Turn on the connected equipment, such as broadband router or the server.
– Confirm the Player and the server are connected to the same access point.
– Set the proper value(s) in the network setting. Check “Network”. (p. 31)
– Depending on the DLNA server, the Player may need to be permitted from the server.
– Make sure the file is playable. (p. 3)
– Check your DLNA server’s setting.
– The playback and operating quality may be affected by your home network condition.
■ Messages on the screen
– The following messages appear on the TV screen in case the disc you tried to play back is not appropriate or the operation is not correct.
Error message
Not Support This File!
Wrong region code!
Network has FAILED.
Network is OK, proxy has
FAILED.
The Setting is prohibited, please setup again.
No valid upgrade file is found!
Upgrade has failed for some reason!
Possible causes and solutions
– The disc is an incompatible region code. See “Region management information” (p. 3).
– This Player cannot be connected to the proxy server. See “Proxy Setting” (p. 31).
– BD-Live connection is prohibited. See “BD-Live Connection” (p. 31).
– Check if the upgrade file is in the appropriate folder.
– Upgrade is failed. Check if the upgrade file is corrupted or unreadable.
5
39
En
GLOSSARY
AVCHD
AVCHD is a new format (standard) for high definition video cameras that can be used to record and play highresolution HD images.
BD-Live
BD-Live is a BD standard that utilizes a network connection, enabling this Player to go online to download promotional videos and other data.
BDMV
BDMV (Blu-ray Disc Movie, BD-MV) refers to one of the application formats used for BD-ROM which is one of the Blu-ray Disc specifications. BDMV is a recording format equivalent to DVD-Video of the DVD specification.
BONUSVIEW
BONUSVIEW compatible discs let you simultaneously enjoy video sub-channel for two screens, audio subchannel and sub-titles. A small screen appears within the main screen during playback (Picture in Picture).
Closed caption
Closed captions are kind of subtitle, and the difference between subtitles and captions is that subtitles are intended for hearing persons and captions are for the hearing impaired. Subtitles rarely show all of the audio.
For example, captions show sound effects (e.g., “phone ringing” and “footsteps”), while subtitles do not. Before you select this setting, please ensure that the disc contains closed caption information.
Color Space
Color Space is a color range that can be represented.
RGB is a color space based on the RGB color model
(red, green and blue) and is typically used for PC monitors. YCbCr is a color space based on a luminance signal (Y) and two color difference signals (Cb and Cr).
Deep Color
Deep Color refers to the use of various color depths in displays, up from the 24-bit depths in previous versions of the HDMI specification. This extra bit depth allows
HDTVs and other displays go from millions of colors to billions of colors and eliminate on-screen color banding for smooth tonal transitions and subtle gradations between colors. The increased contrast ratio can represent many times more shades of gray between black and white. Also Deep Color increases the number of available colors within the boundaries defined by the
RGB or YCbCr color space.
DivX®
DivX® is a popular media technology created by DivX,
Inc. DivX® media files contain highly compressed video with high visual quality that maintains a relatively small file size. DivX® files can also include advanced media features like menus, subtitles, and alternate audio tracks. Many DivX® media files are available for download online, and you can create your own using your personal content and easy-to-use tools from
DivX.com.
Dolby Digital
A sound system developed by Dolby Laboratories Inc. that gives movie theater ambience to audio output when the product is connected to a Dolby Digital processor or amplifier.
Dolby Digital Plus
A sound system developed as an extension to Dolby
Digital. This audio coding technology supports 7.1 multi-channel surround sound.
Dolby TrueHD
Dolby TrueHD is a lossless coding technology that supports up to 8 channels of multi-channel surround sound for the next generation optical discs. The reproduced sound is true to the original source bit-forbit.
DRC (Dynamic Range Control)
DRC lets you adjust the range between the loudest and softest sounds (dynamic range) for playback at average volume. Use this when it is hard to hear dialog, or during times when playback may disturb neighbors.
DSD (Direct Stream Digital)
DSD technology stores audio signals on digital storage media, such as Super Audio CDs. Using DSD, signals are stored as single bit values at a high- frequency sampling rate of 2.8224 MHz, while noise shaping and oversampling are used to reduce distortion, a common occurrence with very high quantization of audio signals.
Due to the high sampling rate, better audio quality can be achieved than that offered by the PCM format used for normal audio CDs.
DTS
This is a digital sound system developed by DTS, Inc. for use in cinemas.
DTS-HD High Resolution Audio
DTS-HD High Resolution Audio is a new technology developed for the next generation high definition optical disc format.
DTS-HD Master Audio
DTS-HD Master Audio is a lossless audio compression technology developed for the next generation high definition optical disc format.
DTS-HD Master Audio | Essential
DTS-HD Master Audio | Essential is a lossless audio compression technology developed for the next generation high definition optical disc format.
HDMI
HDMI (High-Definition Multimedia Interface) is an interface that supports both video and audio on a single digital connection. The HDMI connection carries standard to high definition video signals and multichannel audio signals to AV components such as HDMI equipped TVs, in digital form without degradation.
Letterbox (LB 4:3)
A screen size with black bars on the top and bottom of the image to allow viewing of wide-screen (16:9) material on a connected 4:3 TV.
40
En
Linear PCM Sound
Linear PCM is a signal recording format used for Audio
CDs and on some DVD and Blu-ray discs. The sound on
Audio CDs is recorded at 44.1 kHz with 16 bits. (Sound is recorded between 48 kHz with 16 bits and 96 kHz with 24 bits on DVD discs and between 48 kHz with 16 bits and 192 kHz with 24 bits on BD discs.)
Lip Sync
Lip Sync, an abbreviation for lip synchronization, is a technical term that involves both a problem and a capability of maintaining audio and video signals synchronized during post-production and transmission.
Whereas the audio and video latency requires complex end-user adjustments, HDMI version 1.3 incorporates an automatic audio and video syncing capability that allows devices to perform this synchronization automatically and accurately without user interaction.
Mac address
The Mac address is a unique value assigned to a network device for identification purposes.
SPECIFICATIONS
Pan Scan (PS 4:3)
A screen size that cuts off the sides of the image to allow viewing of wide-screen (16:9) material on a connected
4:3 TV.
Subtitles
These are the lines of text appearing at the bottom of the screen which translate or transcribe the dialog. They are recorded on many DVD and BD discs.
Top menu
In a BD-Video/DVD-Video, this is the menu for selecting things like the chapter to be played back and the subtitle language. In some DVD-Videos, the top menu may be called the “Title Menu”.
x.v.Color
x.v.Color reproduces a greater range of color than before, showing almost all of the colors that the human eye can detect.
5
SPECIFICATIONS
■ General
Power supply
[Central and South America models] ................AC 110–240 V, 50/60 Hz
[Europe and Russia models]........................................... AC 230 V, 50 Hz
[Asia model]......................................................AC 220–240 V, 50/60 Hz
[Taiwan model] ................................................. AC 110-120 V, 50/60 Hz
[Korea model] ................................................................ AC 220 V, 60 Hz
Power consumption (Normal) .............................................................. 25 W
Power consumption (Standby) ............................................................ 0.5 W
Dimensions (W × H × D) ............................................. 435 × 96 × 316 mm
(17-1/8 × 3-3/4 × 12-1/2 in)
Weight ..............................................................................4.05 kg (8.93 lbs.)
■ Audio performance
Audio output level (1 kHz, 0 dB, BD/DVD/CD-DA) .................... 2 ± 0.3 V
Signal to nose ratio (BD/DVD/CD-DA) ..............................115 dB or more
Dynamic range
BD/DVD ...........................................................................105 dB or more
CD-DA ..............................................................................100 dB or more
Harmonic distortion (1 kHz)
BD/DVD ......................................................................... 0.0028 % or less
CD-DA .............................................................................. 0.003 % or less
Frequency response
BD/DVD ............................................ 2 Hz to 22 kHz (48 kHz Sampling)
2 Hz to 44 kHz (96 kHz Sampling)
CD-DA ...............................................................................2 Hz to 20 kHz
■ Input/output
HDMI output .............................................................. Type A connector × 1
480i/576i/480p/576p/720p/1080i/1080p/1080p@24Hz,
Deep Color, x.v. Color support
Component video output ..............................................Y: 1 Vp-p (75 ohms)
P
B
, P
R
: 0.7 Vp-p (75 ohms)
Video output......................................................................1 Vp-p (75 ohms)
Digital output.......................................................... Optical × 1, Coaxial × 1
Analog audio output ..................................................................... 7.1 ch × 1,
Mixed 2 ch × 1
USB ............................................................................ Type A connector × 2
Other output equipments ............................................. Remote IN/OUT × 1,
RS-232C × 1 (for custom installer),
Ethernet × 1
Specifications are subject to change without notice.
41
En
SPECIFICATIONS
■ Copyright
– Audio-visual material may consist of copyrighted works which must not be recorded without the authority of the owner of the copyright. Refer to relevant laws in your country.
– This item incorporates copy protection technology that is protected by U.S. patents and other intellectual property rights of Rovi Corporation.
Reverse engineering and disassembly are prohibited.
– Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
– Manufactured under license under U.S. Patent #’s:
5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535; 7,212,872; 7,333,929;
7,392,195; 7,272,567 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks, & DTS-HD, DTS-HD Master
Audio, and the DTS logos are trademarks of DTS,
Inc. Product includes software. © DTS, Inc. All
Rights Reserved.
– is a trademark.
– “BD-LIVE” logo is a trademark of Blu-ray Disc
Association.
– “BONUSVIEW” is a trademark of Blu-ray Disc
Association.
– is a trademark of DVD Format/Logo
Licensing Corporation.
– HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
– “x.v.Color” and “x.v.Color” logo are trademarks.
– “AVCHD” and the “AVCHD” logo are trademarks of Panasonic Corporation and Sony Corporation.
– Java and all Java-based trademarks and logos are trademarks or registered trademarks of Sun
Microsystems, Inc. in the United States and/or other countries.
– This product is licensed under the AVC patent portfolio license and VC-1 patent portfolio license for the personal and non-commercial use of a consumer to (i) encode video in compliance with the
AVC Standard and VC-1 Standard (“AVC/VC-1
Video”) and/or (ii) decode AVC/VC-1 Video that was encoded by a consumer engaged in a personal and non-commercial activity and/or was obtained from a video provider licensed to provide AVC/VC-
1 Video. No license is granted or shall be implied for any other use. Additional information may be obtained from MPEG LA, LLC.
See http://www.mpegla.com.
– Windows Media Player is a registered trademark or trademark of Microsoft corporation in the United
States and/or other countries.
– DLNA and DLNA CERTIFIED are trademarks and/ or service marks of Digital Living Network Alliance.
– “DivX®, DivX Certified®, DivX Plus™ HD and associated logos are registered trademarks of DivX,
Inc. and are used under license.”
– “DivX Certified® to play DivX® and DivX Plus™
HD (H.264/.MKV) video up to 1080p HD and premium content.”
ABOUT DIVX VIDEO: DivX® is a digital video format created by
DivX, Inc. This is an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand
(VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod.divx.com for more information on how to complete your registration.
42
En
PRECAUCIÓN: LEA LAS INDICACIONES SIGUIENTES ANTES DE
UTILIZAR ESTE APARATO
1 Para asegurar el mejor rendimiento de este aparato, lea atentamente este manual. Y luego guárdelo en un lugar seguro para poder consultarlo en el futuro en caso de ser necesario.
2 Instale esta unidad en un lugar bien ventilado, fresco, seco y limpio, alejado de la luz directa del sol, fuentes de calor, vibración, polvo, humedad y/o frío. Para una adecuada ventilación, permita que el equipo tenga el siguiente espacio libre mínimo:
Superior: 10 cm
Posterior: 10 cm
Laterales: 10 cm
3 Coloque este aparato lejos de otros aparatos eléctricos, motores o transformadores, para evitar así los ruidos de zumbido.
4 No exponga este aparato a cambios bruscos de temperaturas, del frío al calor, ni lo coloque en lugares muy húmedos (una habitación con deshumidificador, por ejemplo), para impedir así que se forme condensación en su interior, lo que podría causar una descarga eléctrica, un incendio, daños en el aparato y/o lesiones a las personas.
5 Evite instalar este aparato en un lugar donde puedan caerle encima objetos extraños y/o donde quede expuesto al goteo o a la salpicadura de líquidos. Encima de este aparato no ponga:
– Otros componentes, porque pueden causar daños y/o decoloración en la superficie de este aparato.
– Objetos con fuego (velas, por ejemplo), porque pueden causar un incendio, daños en el aparato y/o lesiones a las personas.
– Recipientes con líquidos, porque pueden caerse y derramar el líquido, causando descargas eléctricas al usuario y/o dañando el aparato.
6 No tape este aparato con un periódico, mantel, cortina, etc. para no impedir el escape del calor. Si aumenta la temperatura en el interior del aparato, esto puede causar un incendio, daños en el aparato y/o lesiones a las personas.
7 No enchufe este aparato a una toma de corriente hasta después de haber terminado todas las conexiones.
8 No ponga el aparato al revés. Podría recalentarse y posiblemente causar daños.
9 No utilice una fuerza excesiva con los conmutadores, los controles y/o los cables.
10 Cuando desconecte el cable de alimentación de la toma de corriente, sujete la clavija y tire de ella; no tire del propio cable.
11 No limpie este aparato con disolventes químicos porque podría estropear el acabado. Utilice un paño limpio y seco para limpiar el aparato.
12 Utilice solamente la tensión especificada en este aparato.
Utilizar el aparato con una tensión superior a la especificada resulta peligroso y puede producir un incendio, daños en el aparato y/o lesiones a las personas. Yamaha no se hará responsable de ningún daño debido al uso de este aparato con una tensión diferente de la especificada.
13 Para impedir daños debidos a relámpagos, desconecte el cable de alimentación de la toma de corriente durante una tormenta eléctrica.
14 No intente modificar ni arreglar este aparato. Póngase en contacto con el personal de servicio Yamaha cualificado cuando necesite realizar alguna reparación. La caja no deberá abrirse nunca por ninguna razón.
15 Cuando no piense utilizar este aparato durante mucho tiempo
(cuando se ausente de casa por vacaciones, por ejemplo) desconecte el cable de alimentación de la toma de corriente.
16 Asegúrese de leer la sección “RESOLUCIÓN DE
PROBLEMAS” antes de dar por concluido que su aparato está averiado.
17 Antes de trasladar este aparato, pulse p para ponerlo en el modo de espera, y luego desconecte el cable de alimentación de CA de la toma de corriente.
18 La condensación se formará cuando cambie de repente la temperatura ambiental. Desconecte en este caso el cable de alimentación de la toma de corriente y no utilice el aparato.
19 El aparato se calentará cuando la utilice durante mucho tiempo. Desconecte en este caso la alimentación y luego no utilice el aparato para permitir que se enfríe.
20 Instale este aparato cerca de la toma de CA y donde se pueda alcanzar fácilmente la clavija de alimentación.
21 Las baterías no deberán exponerse a un calor excesivo como, por ejemplo, el que producen los rayos del sol, el fuego y similares.
Este aparato no se desconecta de la fuente de alimentación de CA si está conectada a una toma de corriente, aunque la propia aparato esté apagada con p.
A este estado se le llama modo de espera. En este estado, este aparato ha sido diseñada para que consuma un cantidad de corriente muy pequeña.
ADVERTENCIA
PARA REDUCIR EL RIESGO DE INCENDIO O
DESCARGA ELÉCTRICA, NO EXPONGA ESTE
APARATO A LA LLUVIA NI A LA HUMEDAD.
El componente láser de este producto es capaz de emitir radiación que sobrepasa el límite establecido para la clase 1.
Especificaciones LÁSER:
Producto LÁSER de Clase 1
Longitud de onda: 790 nm (CD)/655 nm (DVD)/405 nm (BD)
Salida de láser: máxima de 1 mW
SEGURIDAD CONTRA LA RADIACIÓN LÁSER
Este aparato utiliza rayos láser. Debido a la posibilidad de que se produzcan daños en los ojos, la extracción de la cubierta del aparato o las reparaciones solamente deberán ser realizadas por un técnico cualificado.
PELIGRO
Este aparato emite radiación láser visible cuando se abre.
Evite la exposición directa a los rayos láser. Cuando se conecte este aparato a una toma de corriente no acerque sus ojos a la abertura de la bandeja del disco ni a otras aberturas para mirar al interior.
PRECAUCIÓN
El uso de los controles, los ajustes o los procedimientos que no se especifican enste manual pueden causar una exposición peligrosa a la radiación.
Precaución-i
Es
REPRODUCTOR ............................................. 2
PIEZAS INCLUIDAS............................................ 2
INFORMACIÓN SOBRE DISCOS Y ARCHIVOS........ 3
Para cargar un disco........................................................ 4
Precauciones con los discos............................................ 4
CONTROLES Y FUNCIONES ............................. 5
Panel delantero ............................................................... 5
Mando a distancia........................................................... 6
INTRODUCCIÓN A LAS CONEXIONES........... 10
Panel trasero ................................................................. 10
HDMI CONEXIONES ......................................... 12
Conexión con el terminal HDMI .................................. 12
CONEXIONES DE VÍDEO ................................. 13
Conexión a la toma de vídeo componente.................... 13
CONEXIONES DE AUDIO................................. 14
Conexión con el terminal/toma de audio digital........... 14
Conexión con las tomas de audio ................................. 15
CONEXIÓN DE RED Y USB.............................. 16
OTRAS CONEXIONES...................................... 17
Conexión a las tomas REMOTE CONTROL............... 17
Conexión del cable de alimentación............................. 17
ASISTENTE INICIAL/CONFIGURACIÓN
SENCILLA ..................................................... 18
Configuración con el Asistente inicial/
Configuración Sencilla............................................. 18
MENÚ HOME/MEDIA ........................................ 19
Reproducción de Foto/Música/Vídeo........................... 19
Uso del contenido de red .............................................. 21
FUNCIONAMIENTO DE REPRODUCCIÓN
AVANZADO ................................................... 22
Menú en pantalla .......................................................... 22
Menú de estado............................................................. 23
Uso de Marcador .......................................................... 24
Reproducción de programa........................................... 24
Uso de la búsqueda ....................................................... 24
Disfrute de BONUSVIEW y BD-Live ......................... 25
Utilización de la función Imagen en Imagen
(reproducción de audio/vídeo secundario) ............... 25
Utilización de la función de BD-Live........................... 25
MENÚ SETUP.................................................... 26
Ejemplo de funcionamiento del menú SETUP............. 28
Configuración General ................................................. 29
Configuración de pantalla............................................. 31
Configuración de audio ................................................ 33
Sistema de Información ................................................ 33
Formatos de salida de audio ......................................... 34
Acerca de los formatos de salida de vídeo ................... 35
ACTUALIZACIÓN DE SOFTWARE .................. 36
Actualización del software ........................................... 36
CONTENIDO
1
RESOLUCIÓN DE PROBLEMAS...................... 37
Alimentación ................................................................. 37
Funcionamiento básico ................................................. 37
Reproducción de disco .................................................. 37
Imagen........................................................................... 38
Sonido ........................................................................... 38
Red ................................................................................ 39
Mensajes en pantalla ..................................................... 39
GLOSARIO ........................................................ 40
ESPECIFICACIONES ........................................ 41
Generalidades................................................................ 41
Rendimiento de audio ................................................... 41
Entrada/salida................................................................ 41
Propiedad intelectual..................................................... 42
(al final de este manual)
Information about software ....................................i
2
3
4
5
■ Acerca de este manual
– Este manual describe cómo utilizar este reproductor con un mando a distancia, excepto cuando no esté disponible. También se puede acceder a algunas de estas operaciones mediante los botones del panel delantero.
– Las notas contienen información importante sobre seguridad e instrucciones de funcionamiento. Las indicaciones señalan consejos de funcionamiento.
– Este manual se ha impreso antes de la fabricación.
El diseño y las especificaciones están sujetos a cambios en parte como resultado de mejoras, etc. En caso de diferencias entre el manual y el producto, este último tiene prioridad.
Iconos utilizados en este manual
Los iconos se utilizan para indicar botones/funciones disponibles para un formato particular.
BD : Vídeo BD
DVD
CD
: Vídeo DVD, DVD-VR, DVD+VR, DVD-Audio
: Audio CD, Super Audio CD
VIDEO
MUSIC
PHOTO
: AVCHD, WMV, DivX
: MP3, WMA
: JPEG
1
Es
INTRODUCCIÓN
QUÉ PUEDE HACER CON ESTE REPRODUCTOR
Configuración sencilla de idioma, resolución, relación de aspecto de la pantalla
Puede ajustar la configuración de idioma y TV.
\
pág. 18
Reproducción de discos BD/DVD/CD/SA-CD/DVD-Audio lanzados comercialmente
*
Además de discos BD, este reproductor también admite la reproducción de otros discos diversos.
\
pág. 22
Reproducción de BONUSVIEW, BD-Live, etc.
*
Puede disfrutar de películas adicionales en los discos BD más recientes.
\
pág. 25
Reproducción de archivos de Vídeo, Música, Foto de un disco
Este reproductor puede reproducir los discos que usted grabe.
* \
pág. 19
Reproducción de archivos de Vídeo, Música, Foto de un disco/ dispositivos de memoria USB
*
Con este reproductor se pueden reproducir archivos grabados en discos/dispositivos de memoria USB.
\
pág. 19
Reproducción de archivos de Vídeo, Música, Foto de un servidor doméstico de red
* **
El contenido del PC se puede reproducir en el televisor o el receptor de A/V conectando este reproductor a un servidor de red.
\
pág. 21
Funcionamiento con el mando a distancia del televisor, receptor de A/V, etc.
Puede conectar dispositivos con un cable HDMI y controlarlos con un único mando a distancia utilizando la función Control HDMI.
\
pág. 29
** Para utilizar esta función es necesaria la configuración de red.
PIEZAS INCLUIDAS
Asegúrese de que con el producto se han suministrado los siguientes accesorios.
Mando a distancia
Pilas (×2)
(AAA, R03, UM-4)
Cable de clavijas de audio
Cable de clavijas de vídeo
Cable de alimentación
2
Es
INFORMACIÓN SOBRE DISCOS Y ARCHIVOS
■ Tipos de discos/archivos que se
pueden utilizar con este reproductor
– En este reproductor se pueden reproducir discos de 12 cm y 8 cm. No utilice un adaptador de 8 cm a 12 cm.
– Utilice discos que sean compatibles con los estándares que se indican con la presencia de logotipos oficiales marcados en la etiqueta del disco.
La reproducción de discos que no cumplan con estos estándares no está garantizada. Además, la calidad de imagen o sonido no está garantizada incluso si tales discos se pueden reproducir.
Formato de datos
Tipo de disco
Formato de grabación
Vídeo BD BD-ROM/BD-R/
BD-RE
DVD-ROM
DVD-R/DVD-R DL/
DVD-RW
DVD+R/DVD+R
DL/DVD+RW
CD-ROM
CD-R/CD-RW
SA-CD
USB
Vídeo DVD/DVD-
Audio
Vídeo DVD/DVD-
VR/AVCHD/disco de datos
Vídeo DVD/
DVD+VR/AVCHD/ disco de datos
CDDA/HDCD
CDDA/disco de datos
SA-CD
--
Red --
--
--
DivX/WMV/MP3/
WAV/WMA/JPEG
DivX/WMV/MP3/
WAV/WMA/JPEG
--
DivX/WMV/MP3/
WAV/WMA/JPEG
--
DivX/WMV/MP3/
WAV/WMA/JPEG
WMV/MP3/WMA/
WAV/JPEG
Asia
Información de gestión de la región
Destino Vídeo BD Vídeo DVD
Código de región
“A” o “ALL”
Número de región
“3” o “ALL”
Taiwán
Corea
Código de región
“A” o “ALL”
Código de región
“A” o “ALL”
3 ALL
Número de región
“3” o “ALL”
3 ALL
Número de región
“3” o “ALL”
Información de gestión de la región
Destino
América Central y del Sur
Vídeo BD
Código de región
“A” o “ALL”
Vídeo DVD
Número de región
“4” o “ALL”
Europa
Rusia
Código de región
“B” o “ALL”
Código de región
“C” o “ALL”
4 ALL
Número de región
“2” o “ALL”
2 ALL
Número de región
“5” o “ALL”
5 ALL
– Los discos y los reproductores de vídeo BD/DVD tienen códigos de región que dictan las regiones en las que se puede reproducir un disco.
– Las operaciones y funciones de vídeo BD/DVD pueden ser diferentes de las explicaciones que aparecen en este manual y algunas operaciones pueden estar prohibidas debido a las configuraciones del fabricante del disco.
– Si se visualiza una pantalla de menú o instrucciones de funcionamiento durante la reproducción de un disco, siga el procedimiento de funcionamiento visualizado.
Notas
– Según el disco, puede que no sea posible la reproducción de algunos de los discos de las tablas de la columna izquierda.
– Finalice todos los medios de reproducción que se reproduzcan en este reproductor.
– “Finalizar” hace referencia a un procesamiento del grabador sobre un disco grabado para que se pueda reproducir en otros reproductores/grabadores, así como en este reproductor. Sólo se podrán reproducir en el reproductor los discos que se hayan finalizado.
(Este reproductor no dispone de función para finalizar discos.)
– No se garantiza la reproducción de todos los archivos del disco, dispositivo de memoria USB y red.
– Un archivo con propiedad intelectual protegida no se puede reproducir a través de un dispositivo de memoria USB o red.
3 ALL
Requisitos de archivos de audio MP3/
WMA/WAV
– Frecuencia de muestreo: entre 32 – 48 kHz (MP3/
WMA), LPCM 44,1 kHz/16 bits/estéreo (WAV)
– Bitrate: entre 8 – 320 kbps (MP3), 32 – 192 kbps
(WMA)
1
3
Es
INFORMACIÓN SOBRE DISCOS Y ARCHIVOS
■ Precauciones con los discos
Requisitos de archivo WMV
– WMV9, la resolución máxima es 1.920 × 1.080.
Acerca de Super Audio CD (SA-CD)
– Formato de audio basado en los estándares actuales de CD pero con mayor cantidad de información, lo que se traduce en un sonido de una calidad superior.
Existen tres tipos de discos: de una capa, de doble capa e híbridos. El disco híbrido puede reproducirse en los reproductores de CD existentes y en los reproductores de Super Audio CD, ya que contiene información de CD de audio estándar y de Super
Audio CD.
Tipo de disco Super Audio CD
Disco de doble capa
Disco de capa híbrida
Disco de una capa
Capa de HD Capa de HD
Disco Super Audio CD híbrido
Capa de CD
Capa de HD
Tenga cuidado con los arañazos y el polvo
– Los discos BD, DVD y CD son sensibles al polvo, a las huellas dactilares y especialmente, a los arañazos.
Es posible que no se pueda reproducir un disco con arañazos. Maneje los discos con cuidado y almacénelos en un lugar seguro.
Almacenamiento apropiado de los discos
Ponga el disco en el centro de la caja y almacene la caja y el disco en posición vertical.
Evite guardar los discos en lugares con luz solar directa, cerca de dispositivos de calefacción o en lugares con alta humedad.
No deje caer los discos ni los someta a vibraciones o impactos fuertes.
Evite almacenar los discos en lugares donde haya mucha cantidad de polvo o humedad
1
Capa de CD que se reproduce en cualquier reproductor de CD
Capa de alta densidad que
2 - DSD estéreo de alta calidad
3
- DSD multicanal de alta calidad
Consejo
– Este reproductor admite la transmisión de datos DSD a través de HDMI con un receptor A/V compatible.
Nota
– Esta unidad no muestra los datos de texto incluidos en los discos en el visor del panel delantero.
■ Para cargar un disco
– Inserte el disco con la etiqueta hacia arriba.
– En el caso de un disco grabado por ambos lados, ponga boca abajo el lado que va a reproducir.
Notas
– La reproducción podría iniciarse automáticamente, dependiendo del disco y la configuración del reproductor.
– El menú podrá visualizarse primero, según el disco.
– El tiempo para cargar el disco puede variar dependiendo del disco.
Precauciones para el manejo
– Si la superficie tiene manchas, límpiela suavemente con un paño suave humedecido (con agua solamente).
Cuando limpie los discos, mueva siempre el paño desde el orificio central hacia el borde exterior.
– No utilice pulverizadores de limpieza de discos de vinilo, bencina, diluyente, líquidos para prevención de electricidad estática u otros disolventes.
– No toque la superficie.
– No adhiera papel ni etiquetas adhesivas en el disco.
– Si la superficie de reproducción de un disco está manchada o raspada, el reproductor podrá decidir que el disco es incompatible y expulsar la bandeja portadiscos, o podría no reproducir el disco correctamente. Limpie cualquier mancha de la superficie de reproducción con un paño suave.
Limpieza de la lente lectora
– No utilice nunca discos de limpieza de venta en el comercio. La utilización de esos discos podría dañar la lente.
– Solicite la limpieza de la lente en el centro de atención al cliente aprobado por Yamaha más cercano.
4
Es
■ Panel delantero
CONTROLES Y FUNCIONES
1 2 3 4
1 p (Encendido/En espera)
3 Indicador SA-CD: Se enciende cuando se carga un
SA-CD y se selecciona la capa SA-CD (pág. 4).
4 Visor del panel delantero
5 Bandeja portadiscos (pág. 4)
5
6 (Expulsar): Abre/cierra la bandeja portadiscos.
7 (Búsqueda hacia atrás/Salto hacia
atrás): Pulse para saltar hacia atrás y mantenga pulsado para buscar hacia atrás.
6 7 8 9 0 A B
8 (Búsqueda hacia adelante/Salto hacia adelante):
Pulse para saltar hacia adelante y mantenga pulsado para buscar hacia adelante.
9
0
(Reproducción)
(Pausa)
A (Detener)
B PURE DIRECT: Pulse esta opción para cambiar el
modo Pure Direct (pág. 7) a modo 1/modo 2/
desactivado. Este botón se enciende cuando el modo
Pure Direct se sitúa en modo 1/modo 2.
Instalación de las pilas en el mando a distancia
2
3
1
Alcance aproximado de funcionamiento del mando a distancia
Sensor del mando a distancia
30˚
6 m
30˚
Notas
– No someta al mando a distancia a golpes, agua ni humedad excesiva.
– El mando a distancia podría no funcionar si el sensor del reproductor está expuesto a la luz solar directa o cualquier otra luz fuerte.
– El uso incorrecto de las pilas puede provocar que revienten o tengan fugas. Lea las advertencias para las pilas y utilícelas correctamente.
– No mezcle pilas viejas y nuevas, ni mezcle diferentes marcas.
– Extraiga las pilas si no va a utilizar el mando a distancia durante un periodo de tiempo prolongado.
– Deshágase de las pilas según la normativa de su región.
5
Es
1
CONTROLES Y FUNCIONES
■ Mando a distancia
Nota
– En la esquina superior izquierda de la pantalla aparecerá
cuando la tecla pulsada no esté disponible.
1 Transmisor de señales infrarrojas: Emite la señal infrarroja. Oriente esta ventana al sensor del
(pág. 24) en un punto especificado de una película.
Tras definir un Marcador, para seleccionar el punto de ajuste al que desea saltar, pulse DIGEST. Puede definir hasta 12 marcadores.
3 : Abre/cierra la bandeja portadiscos.
4 PROGRAM Establece el orden de
reproducción (pág. 24). Puede configurar hasta
15 pistas (para discos de audio) o títulos/capítulos
(Vídeo DVD).
5 Teclas de colores BD : Utilice estas teclas según las instrucciones en pantalla.
6 Teclas numéricas: Permiten introducir números, o durante la reproducción, saltar a la pista/capítulo correspondiente al número introducido. Es posible que estos botones no estén disponibles en función del tipo de disco y la situación de reproducción.
7 CLEAR: Borra el número introducido o elemento establecido.
8 SETUP: Muestra la pantalla de menú SETUP
en imagen (pág. 25). Marca PIP (
) se muestra en pantalla cuando esta función está disponible. También puede seleccionar este elemento desde el menú en
Nota
– Marca PIP se muestra sólo cuando la Marca PIP está
0 2ND AUDIO BD : Selecciona el audio secundario de
la función Imagen en imagen (pág. 25) o los
comentarios de audio. Cuando esta función está disponible se muestra en pantalla Marca Audio
Secundario (
seleccionar este elemento desde el menú en pantalla
Nota
– Marca Audio Secundario se muestra sólo cuando la
Marca Audio Secundario está encendida (pág. 30).
6
Es
CONTROLES Y FUNCIONES
A TOP MENU BD DVD : Muestra la pantalla de
menú principal (pág. 41) si el disco contiene un menú.
Seleccione el elemento deseado mediante 5/a /2/3 y ENTER.
Nota
– Las operaciones concretas pueden diferir dependiendo del disco. Siga las instrucciones de cada pantalla de menú,
B Teclas de cursor (5/a/2/3): Permiten mover la selección en la pantalla de menú.
ENTER: Elige el menú/elemento seleccionado.
C RETURN: Permite volver al menú o pantalla anterior, etc.
D SUBTITLE :
el idioma de los subtítulos (pág. 41) si está disponible.
También puede seleccionar este elemento desde el
E STATUS: Muestra la información de reproducción
F Teclas de control
BD DVD CD VIDEO MUSIC PHOTO
/ : Permite buscar hacia atrás/hacia adelante.
La velocidad de búsqueda cambiará cada vez que pulse la techa (buscar hacia atrás/adelante: 5 pasos cada una).
Pulse para reanudar la reproducción normal.
/ BD DVD CD VIDEO MUSIC :
Manténgalo pulsado para realizar una búsqueda o una repetición instantánea. La búsqueda instantánea salta
30 segundos en el contenido. La repetición instantánea reproduce el contenido desde 10 segundos antes.
/ : Permite saltar hacia atrás/hacia adelante.
: Detiene la reproducción. Para detener la reproducción completamente, pulse este botón dos veces.
: Pausa la reproducción.
: Reproduce el contenido.
( )/ ( )
BD DVD : Realiza una ejecución lenta hacia atrás/ hacia adelante. La velocidad de reproducción lenta cambiará cada vez que pulse la tecla (reproducción lenta hacia atrás/adelante: 4 pasos cada una).
Estos botones también permiten la reproducción de avance/retroceso de fotograma durante la pausa.
Pulse para reanudar la reproducción normal.
Muchos discos de DVD-Audio permiten reproducir pases de diapositivas y girar páginas. Pulse / para pasar a una página anterior o siguiente. Esta función sirve solamente para los DVD-Audio.
Notas
– Algunos discos BD/DVD no son compatibles con la reproducción de avance/retroceso de fotograma.
– En función del disco, el reproductor reanuda la reproducción desde el punto en el que se paró anteriormente el reproductor. Para reproducir desde el principio, pulse y después .
G SA-CD/CD: Cambia la capa de reproducción de un
SA-CD híbrido entre SA-CD y CD (pág. 4).
1
Consejo
– El indicador SA-CD/CD (pág. 5), situado en el panel
delantero, se enciende cuando se carga un SA-CD
y se selecciona la capa SA-CD (pág. 33).
Notas
– Las señales de audio solamente se emiten desde las
tomas AUDIO OUT (pág. 11) si la capa SA-CD está
seleccionada.
– No es posible reproducir en este reproductor señales de audio grabadas en formato DSD multicanal.
H PURE DIRECT: Permite cambiar el modo Pure
Direct. El modo Pure Direct mostrado a continuación cambiará cada vez que se pulse el botón. El modo Pure
Direct mejora la calidad del sonido. En el panel delantero, se enciende PURE DIRECT cuando el modo Pure Direct está en modo 1/modo 2.
Modo 1: el panel delantero se apaga y no se emiten señales de vídeo. Este modo es ideal para escuchar audio.
Modo 2: el visor del panel delantero se apaga y no se emiten las señales de vídeo que no sean del terminal
HDMI. Este modo es adecuado para ver películas con sonido de alta calidad.
desactivado: Reproducción normal.
I DIMMER: Cambia el brillo del visor del panel delantero en 5 pasos.
PHOTO miniatura. Cuando se muestran las miniaturas, puede continuar a la página siguiente o anterior con /
DVD VIDEO
K p: Enciende el reproductor o lo pone en modo de espera.
.
L ZOOM : zoom. El tamaño de la pantalla cambiará cada vez que pulse la tecla (ampliar/reducir zoom: 3 pasos cada uno).
Continúa en la página siguiente.
\
7
Es
CONTROLES Y FUNCIONES
M SEARCH :
Permite saltar a un punto especificado durante la reproducción. Para conocer los detalles sobre esta
función, consulte “Uso de la búsqueda” (pág. 24).
También puede seleccionar este elemento desde el
N HOME: Muestra la pantalla de menú HOME (pág. 19).
O REPEAT :
Permite cambiar el modo de repetición. El modo de repetición mostrado a continuación cambiará cada vez que se pulse el botón.
: Permite repetir el título que se está reproduciendo.
: Permite repetir el capítulo que se está reproduciendo.
: Repite todas las pistas o los archivos del disco o carpeta.
: Repite la pista o el archivo que se está reproduciendo.
P A/B : reproducir una parte específica que desee repetir.
1 Pulse A/B en la escena donde desee establecer el punto inicial. En la pantalla se muestra “A-”.
2 Vuelva a pulsar A/B en la escena donde desee establecer el punto final. En la pantalla se muestra
“A-B”. Se inicia la reproducción de repetición.
3 Para cancelar la reproducción de repetición, pulse
A/B. “A-B” desaparece y finaliza la reproducción de repetición.
Nota
– Es posible que esta función no se pueda realizar dependiendo de las especificaciones del disco.
emergente. Los contenidos del menú que se visualiza varían en función del disco. Consulte los detalles sobre cómo ver y operar el menú emergente en el manual del disco.
La pantalla del menú principal se puede mostrar pulsando POP-UP/MENU, dependiendo del DVD.
R ON SCREEN: Muestra el menú en pantalla (pág. 22).
BD DVD cámara si el vídeo se ha grabado con varios ángulos.
Cuando esta función está disponible se muestra en pantalla
Marca de Angulo ( ). También puede seleccionar este
elemento desde el menú en pantalla (pág. 22).
Nota
– Marca de Angulo se muestra sólo cuando la Marca
de Angulo está encendida (pág. 30).
BD DVD o formato de audio. También puede seleccionar este
elemento desde el menú en pantalla (pág. 22).
8
Es
Función ID
Puede modificar el ID del mando a distancia para evitar una utilización no deseada de otro reproductor Yamaha, como un reproductor de DVD. Si modifica el ID del mando a distancia, seleccione el mismo ID para la unidad principal. La configuración predeterminada es ID1.
1 Configuración del mando a distancia
Para modificar el ID de ID1 a ID2, mantenga pulsado el botón de color rojo y el botón 2 de los botones numéricos simultáneamente durante
3 segundos. Para modificar el ID de ID2 a ID1, mantenga pulsado el botón de color rojo y el botón 1 de los botones numéricos simultáneamente durante 3 segundos.
2 Configuración de la unidad principal
Mantenga pulsado y panel delantero simultáneamente durante
en el
2 segundos para mostrar el ID actual si:
– No hay ningún disco en el reproductor.
– La bandeja portadiscos está cerrada.
– Se detiene la reproducción.
– “NO DISC” aparece en el visor del panel delantero.
Mantenga pulsadas las teclas durante 2 segundos más para cambiar el ID de ID1 a ID2.
Nota
– Si el mando a distancia está sin pilas durante unos minutos o si se dejan pilas agotadas en el mando a distancia, el ID del mando a distancia se ajusta automáticamente en ID1. Si desea utilizar el mando a distancia con el ajuste ID2, coloque pilas nuevas y vuelva a configurar el ID del mando a distancia.
CONTROLES Y FUNCIONES
1
9
Es
CONEXIONES
INTRODUCCIÓN A LAS CONEXIONES
Encuentre el método de conexión que corresponde a su equipo de vídeo/audio. Le recomendamos que utilice el terminal
HDMI que ofrece audio y vídeo digital de alta calidad en una única conexión. Si utiliza los demás terminales/conectores, conecte el vídeo en primer lugar. A continuación, conecte el audio.
Conecte el vídeo y audio al receptor de A/V mediante cable
HDMI.
¿Terminal HDMI en el receptor de A/V? *
¿Terminal HDMI en el televisor?
INICIO
Consulte el manual de instrucciones del receptor de A/V.
¿Terminal HDMI en el televisor?
Conecte el vídeo al televisor mediante cable HDMI.
¿Utilizar receptor de A/V?
Conecte el vídeo al receptor de AV.
¿Terminal HDMI en el televisor?
Conecte el vídeo y el audio al televisor mediante cable HDMI.
Sí
No
■ Panel trasero
Conecte el vídeo al televisor.
* Cuando conecte a un receptor de A/V que no pueda dar salida a la entrada de sonido a través de su terminal HDMI, consulte el manual de instrucciones del receptor de A/V.
10
Es
1 2 3 4 5 6 7 8 9 0 A
Conexiones para vídeo al televisor
A’
al receptor de A/V
B
o
C
Conexiones de vídeo al televisor
B’
o
C’
Conecte el audio al receptor de AV.
Conecte el audio al televisor.
Conexión de audio y vídeo al receptor de A/V
A
Conexiones de audio para el receptor de A/V
D
o
E
o
F
o
G
Sonido envolvente de 7.1 canales (pág. 15)
Conexiones de vídeo y audio al televisor
A’
Conexiones de audio al televisor
D’
o
E’
o
F’
2
4 REMOTE CONTROL (IN/OUT/RS-232C)
5 Sonido envolvente de 7.1 canales
6 MIXED 2CH (AUDIO OUT) (pág. 15)
11
Es
HDMI CONEXIONES
■ Conexión con el terminal HDMI
– Puede disfrutar de imagen y sonido digital de alta calidad a través del terminal HDMI.
– Conecte con firmeza un cable HDMI (de venta en el comercio) a los terminales HDMI.
– Consulte la página 34 para obtener información sobre los formatos de salida de audio/vídeo.
– Utilice cables HIGH SPEED HDMI que dispongan del logotipo HDMI (tal como se muestra en la cubierta trasera).
¡Precaución!
No conecte el cable de alimentación del reproductor hasta haber finalizado todas las conexiones.
Este reproductor
Consejos
– Cuando utilice la función Control HDMI,
consulte “Control HDMI” (pág. 29).
– Para más información sobre el modo de salida
del terminal HDMI, consulte “HDMI” (pág. 33).
Al terminal
HDMI
Cable HDMI
(de venta en el comercio)
A A’
Receptor de A/V
Al terminal de entrada
HDMI
HDMI IN
TV
12
Es
CONEXIONES DE VÍDEO
■ Conexión a la toma de vídeo componente
– Puede disfrutar de una reproducción de color precisa y de imágenes de alta calidad a través de las tomas de componente.
– Conecte con firmeza un cable de vídeo componente (vendido en comercios) o un cable de clavijas de vídeo a la toma COMPONENT/toma de VIDEO.
– Consulte la página 35 para obtener información sobre los formatos de salida de vídeo.
2
¡Precaución!
No conecte el cable de alimentación del reproductor hasta haber finalizado todas las conexiones.
Este reproductor Este reproductor
A la toma
COMPONENT
B
Cable de vídeo componente
(de venta en el comercio)
B’
A las tomas de entrada de componente
Cable de clavijas de vídeo
(suministrado)
C
(Amarillo)
A la toma
VIDEO
A la toma de entrada de vídeo
COMPONENT IN
P
R
(Rojo)
P
B
(Azúl)
(Verde)
Y
(Amarillo)
VIDEO
AV INPUT
Receptor de A/V TV Receptor de A/V TV
Nota
– Si reproduce la imagen mediante una vídeograbadora, la imagen puede deteriorarse debido a la función de protección contra la copia.
C’
13
Es
CONEXIONES DE AUDIO
■ Conexión con el terminal/toma de audio digital
– Puede conectar el equipo de audio o el televisor en la toma COAXIAL o el terminal OPTICAL.
– Conecte con firmeza un cable de audio digital coaxial (de venta en el comercio) o un cable óptico (de venta en el comercio) a la toma de audio digital coaxial o al terminal de audio digital óptico.
– Consulte la información sobre los formatos de salida de audio en la página 34.
¡Precaución!
No conecte el cable de alimentación del reproductor hasta haber finalizado todas las conexiones.
Este reproductor Este reproductor
A la toma
COAXIAL
Al terminal
OPTICAL
D
Cable de audio digital coaxial
(de venta en el comercio)
E
A la toma de entrada coaxial
Cable óptico
(de venta en el comercio)
E’
Al terminal de entrada óptica
COAXIAL
AV INPUT
OPTICAL
DIGITAL AUDIO IN
Receptor de A/V TV Receptor de A/V TV
Consejo
14
Es
CONEXIONES DE AUDIO
■ Conexión con las tomas de audio
– Puede conectar el equipo de audio o el televisor en las tomas MIXED 2CH/sonido envolvente de 7.1 canales.
– Conecte con firmeza cables de clavijas de audio (suministrados o vendidos en comercios) a las tomas MIXED 2CH o las tomas de sonido envolvente de 7.1 canales.
– Consulte la información sobre los formatos de salida de audio en la página 34.
– Si desea reproducir audio SA-CD y DVD-Audio multicanal, conecte las tomas de sonido envolvente de 7.1 canales a las tomas de entrada correspondientes del receptor de A/V mediante cables de clavijas de audio vendidos en comercios.
2
¡Precaución!
No conecte el cable de alimentación del reproductor hasta haber finalizado todas las conexiones.
Este reproductor Este reproductor
G
A las tomas
AUDIO OUT
MIXED 2CH
F
A la toma de entrada de audio
(Blanco) (Rojo)
AUDIO
L R
AUDIO IN
Cable de clavijas de audio
(suministrado)
A las tomas de sonido envolvente de 7.1 canales
Cables de clavijas de audio (suministrados y vendidos en comercios)
F’
A la toma
MULTI CH IN
CENTER SUBWOOFER SURROUND BACK SURROUND FRONT
L R
(Blanco) (Rojo)
L R L R
(Blanco) (Rojo) (Blanco) (Rojo)
MULTICH IN
Receptor de A/V TV Receptor de A/V
Consejos
– Puede conectar un altavoz de graves directamente a la toma SUBWOOFER. Si conecta el televisor directamente a este reproductor, conecte un altavoz de graves activo, como el Yamaha Active Servo Processing Subwoofer
System, a esta toma.
15
Es
CONEXIÓN DE RED Y USB
■ Conexión con el terminal NETWORK y el puerto USB
– El contenido del PC se puede reproducir conectando este reproductor a la red.
– Puede disfrutar de una variedad de contenido con funciones interactivas gracias a la conexión a Internet cuando
funciones de BD-Live.
– Puede conectar un dispositivo de memoria USB (2 GB o superior y formateado con FAT 32/16) para BD
Almacenamiento Local al puerto USB del panel posterior (o delantero) del reproductor para guardar los datos
BD-Live o para actualizar el software de este reproductor. Para guardar los datos en el dispositivo de memoria USB
del panel frontal, consulte “Almacenamiento Local” (pág. 29).
– Conecte con firmeza un cable de red (vendido en comercios) y un dispositivo de memoria USB
(vendido en comercios) al terminal NETWORK y al puerto USB.
– Utilice sólo un cable de red STP (par trenzado blindado).
– Cuando se emplee Internet, se necesita una conexión a Internet de banda ancha como se muestra más abajo.
– Conecte el otro conector del cable de red al nodo/enrutador de banda ancha.
Antes de utilizar el dispositivo de memoria USB
Este reproductor
PRECAUCIÓN:
– No desconecte el dispositivo de memoria
USB ni desenchufe el cable de alimentación mientras se estén realizando las operaciones
de Almacenamiento Local (pág. 29) o se
esté llevando a cabo la actualización del software.
– No utilice un cable de extensión USB cuando conecte un dispositivo de memoria
USB al puerto USB del reproductor. El uso de un cable de extensión USB podría impedir que el reproductor funcione correctamente.
Al terminal
NETWORK Al puerto USB
Nota
– Yamaha no puede garantizar que todas las marcas de dispositivos de memoria
USB funcionen con este reproductor.
Cable de red
(de venta en el comercio)
Dispositivo de memoria USB
(de venta en el comercio)
Notas
– Cuando utilice una conexión a Internet de banda ancha, es necesario un contrato con un proveedor de servicios de Internet. Para más información, póngase en contacto con su proveedor de servicios de Internet más cercano.
– Consulte el manual de manejo de su equipo ya que el equipo conectado y el método de conexión pueden variar dependiendo de su entorno de Internet.
– Emplee un cable de red/enrutador compatible con 10BASE-T/100BASE-TX.
Internet
Al terminal LAN
Módem
LAN
Nodo o enrutador de banda ancha
Después de la conexión
– Para establecer el parámetro de Red manualmente, consulte “Red” (pág. 31).
– Para reproducir el contenido del PC en su red, consulte “Uso del contenido de red” (pág. 21).
PC
16
Es
OTRAS CONEXIONES
■ Conexión a las tomas REMOTE
CONTROL
– Puede transmitir y recibir las señales del mando a distancia conectando a las tomas REMOTE
CONTROL (OUT/IN).
– Conecte con firmeza cables con mini clavija mono de 3,5 mm (de venta en el comercio) en los terminales REMOTE CONTROL (OUT/IN).
– Si su receptor de AV es un producto Yamaha y tiene la capacidad de transmitir señales de control
SCENE, puede controlar el reproductor con la función SCENE.
– Puede conectar un componente Yamaha (como, por ejemplo, un reproductor de CD) que sea compatible con la función SCENE a la toma REMOTE
CONTROL (OUT) de este reproductor.
– El terminal RS-232C es un terminal de ampliación de control para usos comerciales. Solicite más información a su distribuidor.
■ Conexión del cable de
alimentación
– Después de realizar todas las conexiones, enchufe el cable de alimentación suministrado a la AC IN de la parte trasera del reproductor. A continuación enchúfelo en una toma de CA.
2
¡Precaución!
No conecte el cable de alimentación del reproductor hasta haber finalizado todas las conexiones.
Este reproductor
A AC IN
A la toma
REMOTE
CONTROL (OUT)
Cable con mini clavija mono de 3,5 mm
(de venta en el comercio)
A la toma de salida del mando a distancia
REMOTE CONTROL IN
A la toma
REMOTE
CONTROL (IN)
Cable con mini clavija mono de 3,5 mm
(de venta en el comercio)
A la toma de entrada del mando a distancia
REMOTE CONTROL OUT
A la toma de CA
Nota
– PARA PREVENIR EL RIESGO DE DESCARGAS
ELÉCTRICAS, NO TOQUE LAS PARTES SIN
AISLAMIENTO DE NINGÚN CABLE CUANDO EL
CABLE DE ALIMENTACIÓN ESTÉ CONECTADO.
Componente Yamaha Receptor de señales infrarrojas o componente Yamaha
(por ejemplo, un receptor A/V)
Consejos
– Para más detalles sobre la función SCENE, consulte el manual de instrucciones de su receptor de A/V
Yamaha.
17
Es
REPRODUCCIÓN
ASISTENTE INICIAL/CONFIGURACIÓN SENCILLA
■ Configuración con el Asistente
inicial/Configuración Sencilla
Asistente inicial/Configuración Sencilla le permite establecer con facilidad el idioma, la resolución y la relación de aspecto de pantalla. La pantalla Asistente inicial se muestra cuando enciende el reproductor por primera vez después de la compra o actualización. El mismo ajuste se puede realizar desde el menú SETUP = Sistema = Configuración Sencilla.
1 Cuando se muestre la pantalla Configuración Sencilla, pulse ENTER para iniciar Configuración Sencilla.
4 Pulse 5/a para seleccionar la relación de aspecto de pantalla, a continuación pulse ENTER. Para más detalles sobre la configuración de elementos, consulte
La Configuración Sencilla se ha completado.
2 Pulse 5/a para seleccionar el idioma que desea ver en la pantalla y, después, pulse ENTER.
Nota
– Si no se muestra la imagen tras completar Asistente inicial/Configuración Sencilla, consulte
“RESOLUCIÓN DE PROBLEMAS” (pág. 38).
3 Pulse 5/a para seleccionar la resolución, a continuación pulse ENTER. Para obtener detalles sobre la configuración de elementos, consulte
18
Es
MENÚ HOME/MEDIA
Los menús HOME y MEDIA le permiten examinar y reproducir archivos multimedia en discos de datos, dispositivos de memoria USB y su red.
Nota
– Para conocer los detalles sobre los discos y formatos
que se pueden reproducir, consulte la página 3.
■ Reproducción de Foto/Música/
Vídeo
Operaciones comunes para la reproducción de archivos en una carpeta seleccionada
Ejemplo: Selección de un archivo de película en un dispositivo de memoria USB
Nota
– Detenga la reproducción del vídeo antes de desplazarse a la pantalla de menú MEDIA.
1 Pulse HOME para pasar a la pantalla del menú HOME.
Pulse 2/3 para seleccionar MEDIA y pulse ENTER.
3
Funcionamiento básico
5/a: Mueve la selección.
2: Vuelve a la carpeta principal.
3: Activa/desactiva el archivo/carpeta simple.
HOME: Permite entrar/salir de la pantalla de menú HOME.
ENTER: Confirma la carpeta/archivo.
POP-UP/MENU: Se abre Menú de Edición.
HOME
2ND
AUDIO
TOP MENU
A/B
POP-UP/MENU
RETURN
ENTER
ON SCREEN
Iconos sobre el menú MEDIA
: Reproduce el disco que hay en la bandeja o muestra el contenido del disco de datos.
: Muestra el contenido del dispositivo de memoria
USB conectado al puerto USB.
: Busca un servidor DLNA (pág. 21) en la red.
: Muestra el contenido del servidor DLNA conectado.
2 Aparece la pantalla MEDIA.
3 Seleccione el elemento que contiene el archivo que desea reproducir, a continuación pulse ENTER.
19
Es
MENÚ HOME/MEDIA
4 Seleccione la carpeta Foto, Música, Vídeo o AVCHD que desea reproducir, a continuación pulse ENTER.
Para volver a la carpeta principal, pulse 2 o seleccione .
Nota
– Tenga en cuenta que en el siguiente paso sólo se mostrarán los archivos del tipo que seleccione en este paso. Por ejemplo, si selecciona la carpeta Foto en este paso, sólo se mostrarán archivos de fotos después de este paso. Cuando desee reproducir un tipo de archivo distinto a foto, vuelva a esta jerarquía y seleccione de nuevo el tipo de archivo.
5 Seleccione las carpetas que contienen el archivo que desea reproducir.
Consejo
– Para disfrutar del pase de diapositivas con música, pulse HOME para volver a la pantalla de menú HOME mientras se reproduce la música y seleccione archivo de fotos.
Nota
– Es posible que el archivo mostrado no se reproduzca dependiendo del contenido.
Operaciones para visualización de fotos
Mientras se ven fotos los botones del mando a distancia funcionan como se indica a continuación.
: Detiene el pase de diapositivas y vuelve al explorador de archivos.
: Establece una pausa en un pase de diapositivas.
: Reproduce un pase de diapositivas.
: Pasa a la fotografía siguiente.
: Pasa a la fotografía anterior.
: Acelera un pase de diapositivas en 3 pasos.
: Ralentiza un pase de diapositivas en 3 pasos.
5: Invierte una foto.
a: Muestra la foto reflejada.
2: Gira una foto en sentido contrario a las agujas del reloj.
3: Gira una foto en el sentido de las agujas del reloj.
ZOOM: Amplía/reduce una foto (ampliar/reducir zoom:
3 pasos cada uno).
5/a/2/3: Permite desplazarse en modo de zoom cuando la foto es mayor que la pantalla.
DIGEST: Cambia a modo de miniaturas (pág. 7). Cuando
se muestran las miniaturas, puede continuar a la página siguiente o anterior con / .
6 Seleccione el archivo que desea reproducir, a continuación pulse ENTER.
Cuando se selecciona un archivo de vídeo se inicia la reproducción.
Cuando se selecciona un archivo de música, se muestra la pantalla de estado y se inicia la reproducción.
Cuando se selecciona un archivo de fotografía se inicia el pase de diapositivas.
20
Es
■ Uso del contenido de red
Este reproductor es un reproductor multimedia digital certificado para DLNA. Puede administrar contenido de fotos, música y vídeo almacenado en servidores DLNA en su red doméstica.
Acerca de DLNA
DLNA (Digital Living Network Alliance) permite compartir de forma sencilla medios digitales a través de una red doméstica y puede disfrutar del contenido digital almacenado en su software, PC instalado, servidor DLNA u otro dispositivo compatible con DLNA con su TV a través de este reproductor. Para conectar este reproductor a sus servidores
DLNA se requieren algunos ajustes del dispositivo o del servidor DLNA. Para más detalles, consulte el software del servidor DLNA o el dispositivo DLNA.
Reproducción de contenido compartido
1 Para reproducir archivos en el PC, instale un software de servidor DLNA como, por ejemplo Windows Media
Player 12 y comparta los archivos que desee reproducir.
2 Encienda el PC con el software de servidor DLNA instalado o el dispositivo DLNA conectado a su red doméstica.
3 Pulse HOME para mostrar la pantalla de menú HOME.
Seleccione MEDIA para pasar al menú MEDIA. Los servidores DLNA conectados a la red aparecen en pantalla.
MENÚ HOME/MEDIA
Notas
– La calidad de funcionamiento y reproducción podría verse afectada por las condiciones de la red doméstica.
– Es posible que los archivos de medios extraíbles tales como dispositivos de memoria USB o unidades de DVD del servidor de medios no se compartan correctamente.
3
Notas
– Si su servidor DLNA no aparece en la lista, seleccione Buscar DLNA para buscarlo.
– Dependiendo del servidor DLNA, es posible que sea necesario autorizar al reproductor desde el servidor.
– Para reproducir el archivo en el servidor DLNA, el reproductor y el servidor deben estar conectados al mismo punto de acceso.
– Es posible que los requisitos de archivo no siempre sean compatibles. Podría haber algunas restricciones dependiendo de las características de los archivos y de la capacidad del servidor DLNA.
4 Seleccione el archivo que desee reproducir.
21
Es
FUNCIONAMIENTO DE REPRODUCCIÓN AVANZADO
En este capítulo se explica la reproducción de discos BD y DVD vendidos en comercios, SA-CD, CD y discos
DVD-RW/R grabados.
Nota
– Para conocer el funcionamiento básico de reproducción,
■ Menú en pantalla
Para mostrar el menú en pantalla, pulse ON SCREEN.
A continuación, pulse 5/a/2/3 para seleccionar un elemento, después pulse ENTER para utilizar la función deseada.
Consejo
– Cuando se reproduce un DVD-Vídeo, puede seleccionar Aleatorio All, Aleatorio TT (título),
Aleatorio CH (capítulo), Shuffle All, Shuffle TT
(título) y Shuffle CH (capítulo).
Audio : Muestra el idioma/señal de audio del disco BD/DVD seleccionado actualmente.
Puede seleccionar el tipo de audio deseado.
El menú en pantalla consta de los siguientes elementos.
Título : Muestra el número del título que se está reproduciendo. Puede saltar al título deseado seleccionándolo desde este elemento.
Capítulo : Muestra el número del capítulo que se está reproduciendo. Puede saltar al capítulo deseado seleccionándolo desde este elemento.
Pista/Archivo
Muestra el número de la pista o archivo que se está
: reproduciendo. Puede saltar a la pista o al archivo deseado seleccionándolo desde este elemento.
Hora : Muestra el tiempo de reproducción. Seleccione el tipo de visualización entre los siguientes:
– Tiempo de reproducción transcurrido del título, capítulo, disco, pista o archivo
– Tiempo de reproducción restante del título, capítulo, disco, pista o archivo
Modo/Modo de reproducción
DVD CD VIDEO MUSIC PHOTO : Muestra el modo de reproducción actual. Puede seleccionar uno de los modos de reproducción siguientes:
– Normal: Reproducción normal.
– Shuffle: Cada pista/archivo se debe reproducir una vez sin repetición.
– Aleatorio: Reproducción aleatoria real. Se pueden producir repeticiones.
seleccionado actualmente. Si el vídeo se ha grabado con varios ángulos, puede cambiar el ángulo.
Subtítulo : Muestra el idioma de los subtítulos seleccionados actualmente si hay subtítulos.
Estilo subtítulos BD : Muestra el estilo de los subtítulos seleccionados actualmente. Esta función sólo está disponible para subtítulos externos de archivo de vídeo. Puede seleccionar el estilo de texto deseado de los subtítulos.
Bitrate CD : Muestra el bitrate de la señal de audio/vídeo.
Video secundario BD
: Activa o desactiva PIP (pág. 6).
Audio Secundario
BD : Activa o desactiva el audio
Búsqueda Ins
BD DVD CD VIDEO MUSIC : Salta 30 segundos.
Repetición Ins
BD DVD CD VIDEO MUSIC contenido desde 10 segundos antes.
: Reproduce el
Pase de diapositivas PHOTO :
Muestra la velocidad del pase de diapositivas. Puede seleccionar la velocidad del pase de diapositivas entre
Lento/Medio/Rápido.
la pantalla. Puede seleccionar el tipo de transición.
Code Page VIDEO : Permite seleccionar el código de caracteres de los subtítulos que ha agregado al vídeo DivX
22
Es
FUNCIONAMIENTO DE REPRODUCCIÓN AVANZADO
■ Menú de estado
Muestra varios ajustes, cómo los subtítulos, el ángulo y el número de título/capítulo/pista reproducido actualmente.
Para mostrar el menú de estado, pulse STATUS. El menú de estado consta de los siguientes menús.
Al reproducir Vídeo BD/Vídeo DVD o archivo de vídeo
Ejemplo: Iconos cuando se reproduce BD
1 2 3 4 5
Cuando se reproduce un disco de audio o archivos de música
Ejemplo: Iconos cuando se reproduce un archivo de música
1 2 3 4 5 6 7
3
8 7 6
1
9 8
(Estado de reproducción)
2 (Modo repetición): Muestra el modo repetición
3 (Icono de tipo de disco/archivo de música)
1 (Estado de reproducción)
2 (Icono de tipo de disco/archivo de vídeo)
3 (Número de título que se reproduce): Puede saltar al título especificado con la tecla SEARCH
4 (Número de capítulo que se reproduce):
Puede saltar al capítulo especificado con la
5 (Tiempo de reproducción transcurrido):
Puede saltar al punto especificado con la
6 (Subtítulos seleccionados actualmente):
Puede cambiar el idioma de los subtítulos con la tecla SUBTITLE.
7 (Audio seleccionado actualmente): Puede cambiar el formato o idioma de audio con la tecla AUDIO.
8 (Modo repetición): Muestra el modo repetición
contenidos en el archivo.
5 (Número de pista/archivo que se
reproduce): Puede saltar a la pista especificada con
musical si está contenida en el archivo.
7 (Tiempo de reproducción transcurrido):
Puede saltar al punto especificado con la tecla
8 (Barra de progreso) MUSIC progreso de la canción actual.
: Muestra el estado de
9 (Medidor de nivel de audio): Muestra el nivel de volumen actual.
Cuando se visualizan fotos
1
2
(Estado de reproducción)
(Icono de archivo de fotos)
3 (Número de archivo que se muestra)
4 (Modo repetición): Muestra el modo repetición
5 (Velocidad de pase de diapositivas)
23
Es
FUNCIONAMIENTO DE REPRODUCCIÓN AVANZADO
■ Uso de Marcador
DVD VIDEO
Le permite establecer un Marcador en un punto especificado del vídeo. Después de establecer el
Marcador, puede saltar al punto utilizando esta función.
Puede definir hasta 12 marcadores.
1 Pulse MARKER durante la reproducción de la película para definir el Marcador. Se muestran el número de
Marcador y el estado.
2 Pulse ENTER para programar el orden de reproducción.
Para un disco de audio, pulse 5/a para seleccionar una pista deseada y, a continuación, pulse ENTER.
Para un disco DVD-Vídeo, seleccione un título deseado (mostrado como TT) y capítulo (mostrado como CH) en lugar de una pista.
Para borrar una pista establecida, seleccione la pista que desea borrar y, a continuación, pulse CLEAR.
Pulse RETURN para cancelar la reproducción del programa.
2 Después de establecer el Marcador, pulse DIGEST para mostrar la barra de selección de Marcador.
3 Pulse 2/3 para seleccionar el Marcador que desee reproducir, a continuación pulse ENTER.
Pulse CLEAR para eliminar el Marcador seleccionado.
Nota
– Cuando finaliza la reproducción (por ejemplo, al expulsar el disco o al presionar dos veces), los marcadores se eliminan automáticamente.
■ Reproducción de programa
DVD CD
Esta opción le permite programar el orden de reproducción de las pistas de un disco de audio o de los capítulos de DVD.
Pulse PROGRAM durante la reproducción para mostrar la ventana PROGRAMA para programar el orden de reproducción.
Puede programar hasta 15 pistas/capítulos.
Ejemplo: Programación del orden de reproducción de pistas de CD
1 Pulse PROGRAM durante la reproducción.
3 Una vez finalizada la programación, pulse para definir e iniciar la reproducción del programa.
4 Para cancelar la reproducción del programa, detenga la reproducción por completo pulsando dos veces.
■ Uso de la búsqueda
BD DVD CD VIDEO MUSIC
Esta opción le permite saltar a un punto específico durante la reproducción.
1 Pulse SEARCH durante la reproducción. Aparece la barra de estado.
2 Pulse 5/a /2/3 para seleccionar uno de los elementos siguientes, a continuación pulse ENTER.
BD DVD :
– Número de título (mostrado como )
– Número de capítulo (mostrado como )
– Tiempo de título transcurrido (mostrado como )
– Tiempo de capítulo transcurrido (mostrado como
CD :
– Número de pista (mostrado como )
)
– Tiempo de pista transcurrido (mostrado como
– Tiempo de disco transcurrido (mostrado como
VIDEO MUSIC :
– Número de archivo (mostrado como )
– Tiempo de archivo transcurrido (mostrado como )
3 Pulse 5/a o las teclas de número para definir o ajustar el valor del elemento seleccionado y pulse ENTER para saltar al punto especificado.
4 Para cerrar la barra de estado, pulse STATUS.
)
)
24
Es
■ Disfrute de BONUSVIEW y BD-Live
Este reproductor admite las funciones de reproducción de
BONUSVIEW (pág. 40) (BD-ROM Perfil 1 Versión 1.1) y BD-Live (pág. 40) (BD-ROM Perfil 2).
Nota
– Las funciones y el método de reproducción varían según el disco. Siga las indicaciones del disco o del manual de usuario suministrado.
■ Utilización de la función Imagen
en Imagen (reproducción de audio/vídeo secundario)
El Vídeo BD que incluye audio y vídeo secundario compatible con Imagen en Imagen se puede reproducir con audio y vídeo secundario simultáneamente como un vídeo pequeño en la esquina.
Vídeo principal Vídeo secundario
FUNCIONAMIENTO DE REPRODUCCIÓN AVANZADO
■ Utilización de la función de BD-Live
1.
Ajuste de la configuración de red
(pág. 31).
2.
Conecte el dispositivo de memoria
USB al reproductor (pág. 16).
Los datos de BD-Live se guardan en Almacenamiento
Local (pág. 29) (dispositivo de memoria USB conectado
al reproductor). Para disfrutar de estas funciones, conecte un dispositivo de memoria USB (2 GB o superior y formateado con FAT 32/16) compatible con USB 2.0
de alta velocidad (480 Mbit/s) al puerto USB (pág. 16).
– La carpeta BUDA se crea automáticamente en el dispositivo de memoria USB cuando es necesario.
– Si el espacio de almacenamiento es insuficiente, los datos no se copiarán/descargarán. Elimine datos innecesarios o utilice un nuevo dispositivo de memoria USB.
– Puede requerirse algún tiempo para que se carguen
(lectura/escritura) los datos.
3
Notas
– Yamaha no puede garantizar que todas las marcas de dispositivos de memoria USB funcionen con este reproductor.
– No utilice un cable de extensión USB cuando conecte un dispositivo de memoria USB al puerto USB del reproductor. El uso de un cable de extensión USB podría impedir que el reproductor funcione correctamente.
3.
Reproducción del disco.
Mientras se muestra Marca PIP ( ) o Marca Audio Secundario ( ), pulse PIP para activar o desactivar la función Imagen en imagen.
Notas
– Para escuchar audio secundario, asegúrese de que el ajuste Salida de audio (Coaxial/Optica o HDMI) se
ha definido en PCM o Recodificar (pág. 33).
– Dependiendo del disco, para escuchar audio secundario, es posible que tenga que activar el audio
secundario en el menú principal del disco (pág. 7).
– Dependiendo del contenido, el audio y el vídeo secundario para Imagen en Imagen pudiera reproducirse y desaparecer automáticamente.
Además, pudiera haber restricción respecto a las
áreas que pueden visualizarse.
4.
Ejecute BD-Live siguiendo las instrucciones del disco.
Notas
– En relación con el método de reproducción de contenidos
BD-Live, etc., lleve a cabo las operaciones de acuerdo con las instrucciones del manual del disco BD.
– Para disfrutar de las funciones de BD-Live, realice la
conexión de red (pág. 16) y los ajustes de Red (pág. 31).
– Consulte la “Conexión BD-Live” (pág. 31) en
relación con la configuración para restringir el acceso a contenidos BD-Live.
– El tiempo que se necesita para descargar los programas que se ofrecen al dispositivo de memoria
USB conectado en este reproductor depende de las velocidades de conexión a Internet y del volumen de datos de los programas.
– Los programas BD-Live suministrados a través de
Internet podrían no ser capaces de mostrar la conexión dependiendo del estado (actualización) del proveedor.
En tal caso, extraiga el disco y vuelva a intentarlo.
– Si la pantalla BD-Live no aparece durante un rato después de seleccionar la función BD-Live en el menú del disco BD, es posible que el dispositivo de memoria
USB no tenga suficiente espacio libre. En tal caso, expulse el disco del reproductor y, a continuación, borre los datos del dispositivo de memoria USB utilizando el
menú “Formato” de “Almacenamiento Local” (pág. 29).
25
Es
AJUSTES
MENÚ SETUP
El Menú SETUP permite realizar diversos ajustes y configuraciones audiovisuales en las funciones utilizando el mando a distancia.
Menú/Submenú
Sistema
Configuración
General
Idioma
Reproducción
Seguridad
Red
Elemento
Protector de pantalla
Reproducción
Automática Disco
Control HDMI
Control de Red
Cargar configuración por defecto
Actualizar
Configuración
Sencilla
Almacenamiento
Local
OSD
Menú
Audio
Subtítulo
Función
Activa/desactiva el protector de pantalla.
Ajusta el reproductor para que inicie automáticamente la reproducción del disco.
Configura el reproductor para que reciba la señal de control desde el mando a distancia de su receptor de TV/AV.
Activa o desactiva el control a través de Ethernet.
Restablece todos los ajustes a los valores predeterminados, excepto el ajuste Seguridad.
Realiza la actualización del reproductor.
Ajusta el idioma, la resolución y la relación de aspecto de la pantalla.
Muestra el estado de Almacenamiento Local (pág. 29),
formatea Almacenamiento Local y selecciona el puerto
USB delantero o posterior de Almacenamiento Local.
Selecciona el idioma del menú en pantalla.
Permite dar prioridad al idioma del menú del disco.
Permite dar prioridad al idioma del audio.
Permite dar prioridad al idioma de los subtítulos.
Subtítulos
Marca de Angulo
Marca PIP
Marca Audio
Secundario
DivX(R) VOD
DRM
Activa o desactiva los subtítulos.
Ajuste para mostrar la Marca de Angulo cuando se reproducen
BD/DVD con ángulos múltiples.
Ajuste para mostrar la Marca PIP cuando se reproducen BD/
DVD con Imagen en imagen.
Ajuste para mostrar la Marca Audio Secundario cuando se reproducen BD/DVD con audio secundario.
Muestra el código de registro del vídeo DivX(R).
Modo DVD-Audio Ajusta el modo DVD-Audio en DVD-Audio/DVD-Vídeo.
Cambiar
Contraseña
Permite cambiar la contraseña de Control Paterno y Código de país.
Control Paterno Establece el Control Paterno en función del contenido del disco.
Código de país Establece el Código de país.
Conexión a Internet Permite definir la conexión a Internet en Permitir/Desactivar.
Información Muestra la pantalla de información de red.
Prueba de conexión Realiza la prueba de conexión de red.
Configuración IP
DLNA
Configuración
Proxy
Permite definir la configuración IP en Auto/Manual.
Conexión BD-Live Permite definir la conexión a BD-Live en Autorizada/
Permitida Parcialmente/Prohibido.
Permite definir la conexión a DLNA en Permitir/Desactivar.
Permite definir la configuración proxy.
Página
26
Es
MENÚ SETUP
Configuración de audio
Menú/Submenú
Configuración de pantalla
TV
Ajuste de altavoz
Postprocesamiento
Elemento
Pantalla de TV
Resolución
Sistema de TV
Función
Ajusta la relación de aspecto de la pantalla del televisor conectado, y ajusta la salida de vídeo.
Selecciona la resolución del vídeo de salida.
Permite seleccionar el Sistema de TV entre NTSC/PAL/Multi.
Color Space Selecciona el espacio de color entre las opciones RGB/YCbCr
4:4:4/YCbCr 4:2:2/Full RGB.
HDMI Deep Color Permite seleccionar HDMI Deep Color entre 30 bits/36 bits/
Desactivar.
Procesamiento de Video
HDMI 1080p 24Hz Activa o desactiva HDMI 1080p 24Hz.
Sincronismo de labios
Ajusta el retardo entre vídeo y audio, como por ejemplo cuando el movimiento de la boca no se corresponde con la voz.
Modo de Vídeo
Ajuste de color
Contraste automático
Ajusta la imagen visual.
Ajusta Brillo/Saturación/Tonalidad para cada color.
Ajusta el contraste para optimizar la imagen reproducida.
Reducción de ruido Ajusta el nivel de Reducción de ruido.
Modo desentrelazado
Ajusta cómo detectar la señal de vídeo.
Salida de audio Coaxial/Optica Permite seleccionar el modo de salida de la toma COAXIAL/ terminal OPTICAL entre Bitstream/PCM/Recodificar/
Desactivar.
HDMI Permite seleccionar el modo de salida del terminal HDMI entre
Bitstream/PCM/Recodificar/Desactivar.
Downsampling
Salida SACD
DRC
Prioridad SACD
Salida HDMI
Permite seleccionar la frecuencia de submuestreo de la señal de audio digital entre 48k/96k/192k.
Define el DRC (Control de gama dinámica).
Selecciona un contenido cuando se reproduce un SA-CD híbrido.
Selecciona el modo de salida del terminal HDMI entre DSD/
PCM cuando se reproduce un SA-CD.
Configuración
Mezcla descendente
2 Canales
Establece la salida de audio de la toma sonido envolvente de
7.1 canales.
Selecciona el método de mezcla descendente de 2 canales analógico.
Convierte la señal de audio de 2 canales en multicanal.
Muestra la versión de software y la dirección MAC (pág. 41).
Página
4
Sistema de
Información
27
Es
MENÚ SETUP
■ Ejemplo de funcionamiento del
menú SETUP
Debe llamar a la pantalla de menú SETUP para realizar los ajustes en el reproductor. A continuación se explican las operaciones básicas del menú SETUP.
3.
Seleccione un elemento del menú.
Pulse 5/a para seleccionar Control Paterno, a continuación pulse ENTER o el cursor 3.
CLEAR
PIP
TOP MENU
SEARCH
SETUP
HOME
REPEAT
POP-UP/MENU
RETURN
ENTER
ON SCREEN
Ejemplo: Ajuste de Control Paterno
Nota
– Algunos elementos no se pueden ajustar durante la reproducción. En este caso, pulse dos veces para detener la reproducción completamente antes de realizar el ajuste.
1.
Muestre la pantalla de menú SETUP.
Pulse SETUP para mostrar la pantalla de menú SETUP.
Pulse 2/3 para seleccionar Configuración General, a continuación pulse ENTER o a.
4.
Introduzca la contraseña.
Introduzca la contraseña con las teclas numéricas.
– La contraseña predeterminada es 0000.
– No puede ir a la siguiente pantalla de configuración hasta que no haya introducido la contraseña correcta.
– Para cambiar la contraseña, consulte “Cambiar
5.
Seleccione un elemento siguiente.
Pulse 5/a para seleccionar el nivel de Control
Paterno para BD/DVD, a continuación pulse ENTER.
2.
Seleccione un submenú.
Pulse 5/a para seleccionar Seguridad, a continuación pulse ENTER o el cursor 3.
6.
Salga de la pantalla del menú
Pulse 2 para volver al menú anterior.
28
Es
■ Configuración General
Los ajustes predeterminados están marcados con “ * ”.
Sistema
Protector de pantalla
Puede definir el protector de pantalla en activado o desactivado.
Cuando se activa, el reproductor pasará a modo de protector de pantalla si no se utiliza durante 3 minutos. Posteriormente, el reproductor pasará a modo de espera cuando no se utilice durante 6 minutos.
Activar * , Desactivar
Reproducción Automática Disco
Puede activar o desactivar la Reproducción Automática
Disco. Cuando se activa, el disco se reproducirá automáticamente después de cargarlo.
Activar * , Desactivar
Control HDMI
Puede ajustar el reproductor para que reciba una señal de control desde un receptor de TV/AV compatible con la
función Control HDMI a través de un cable HDMI (pág. 12).
Activar, Desactivar *
Utilización de la función Control HDMI
Con la función de Control HDMI, puede operar interactivamente este reproductor con su televisor
(si soporta la función de Control HDMI).
Cuando se conecta el reproductor al televisor compatible con la función de Control HDMI mediante un cable HDMI
y se activa el Control HDMI en el menú SETUP (pág. 29),
puede realizar las funciones indicadas a continuación.
• Función de selección de entrada automática
Cuando inicie la reproducción en este reproductor, el selector de entrada del televisor (y de un receptor A/V si este reproductor esta conectado con el televisor mediante un receptor A/V) cambia automáticamente a este reproductor. La alimentación del televisor se enciende automáticamente dependiendo del televisor.
• Función de apagado automático
Si apaga el televisor cuando este reproductor está en modo de parada y no se visualiza menú SETUP, este reproductor también se apagará automáticamente.
Notas
– Es posible que la función de Control HDMI no funcione correctamente dependiendo del televisor.
– Otras funciones, aparte de las que se han mencionado anteriormente, pueden funcionar según el televisor o receptor A/V.
– Para hacer que la función de Control HDMI esté disponible, configure los ajustes de la función de
Control HDMI en TODOS los componentes (este reproductor, el televisor y el receptor de A/V). Es posible que también sean necesarias determinadas operaciones.
– Cada función se puede configurar de forma independiente para activar o desactivar según el televisor.
– Consulte los detalles relacionados con la configuración en los manuales de funcionamiento que se proporcionan con el televisor y/o el receptor A/V.
MENÚ SETUP
Control de Red
Puede activar el control a través de Ethernet. Este reproductor utiliza el protocolo Yamaha Network
Control (YNC).
Activar, Desactivar *
Notas
– Cuando está activado, el consumo de energía durante el modo de espera aumenta por la función de control de red.
– Cuando está activado, aumenta el tiempo de inicio del sistema.
Cargar configuración por defecto
Puede restablecer todos los ajustes de este reproductor al
ajuste predefinido, excepto el ajuste Seguridad (pág. 30).
Para conocer detalles sobre los ajustes predeterminados,
Actualizar
Puede actualizar el software manualmente desde Disc,
USB Storage o Network. Para conocer detalles sobre la
actualización de software, consulte “ACTUALIZACIÓN
Configuración Sencilla
Puede realizar la Configuración Sencilla (pág. 18).
Almacenamiento Local
Puede mostrar información de Almacenamiento Local, formatear Almacenamiento Local y seleccionar USB
Frontal/USB Trasera para guardar los datos de BD-Live.
Para formatear (vaciar) la carpeta BUDA en el dispositivo de memoria USB, seleccione Información y pulse
ENTER mientras “Formato” está seleccionado en la pantalla.
USB Frontal, USB Trasera *
Almacenamiento Local
Se utiliza como memoria auxiliar cuando se reproduce el disco Blu-ray.
4
29
Es
MENÚ SETUP
Idioma
OSD
Puede seleccionar el idioma de pantalla, es decir, el menú o los mensajes mostrados en pantalla como, por ejemplo, el menú SETUP.
English * , , , , ,
Modo DVD-Audio
Algunos discos DVD-Audio contienen información de
DVD-Vídeo además del contenido de DVD-Audio. Puede seleccionar el modo DVD-Audio o DVD-Vídeo.
DVD-AUDIO * Se reproducen los contenidos de DVD-Audio y Vídeo. En función del disco, tal vez solamente pueda reproducirse el contenido de DVD-Audio.
DVD-VÍDEO Solamente se reproduce el contenido de DVD-Vídeo.
Menú
Puede dar prioridad al idioma del menú del disco.
English * Français Español Deutsch Italiano
Nederlandse , Portugués, Danés, Svenska , Finlandés,
Noruega, , Corea, Japonés, Más
Audio
Puede dar prioridad al idioma del audio para la reproducción de BD/DVD. Para obtener detalles sobre la configuración de
elementos, consulte “Menú” (pág. 30).
Subtítulo
Puede dar prioridad al idioma de los Subtítulo.
Français Español Deutsch Italiano
Nederlandse , Portugués, Danés, Svenska , Finlandés,
Noruega, , Corea, Japonés, Más, Desactivar *
Reproducción
Subtítulos
Puede ajustar que se visualicen los subtítulos (pág. 40)
cuando se reproducen BD/DVD con subtítulos.
Activar, Desactivar *
Marca de Angulo
Puede ajustar la visualización de Marca de Angulo ( ) cuando se reproducen BD/DVD con ángulos múltiples.
Activar * , Desactivar
Marca PIP
Puede ajustar la visualización de Marca PIP ( ) cuando
se reproducen BD (pág. 25) con Imagen en imagen.
Activar * , Desactivar
Marca Audio Secundario
(
Puede ajustar la visualización de Marca Audio Secundario
) cuando se reproducen BD con audio secundario.
Activar * , Desactivar
DivX(R) VOD DRM
Puede mostrar el código de registro del vídeo DivX(R).
Nota
– Este ajuste solamente está disponible si no hay ningún disco cargado.
Seguridad
Cambiar Contraseña
Puede ajustar la contraseña para cambiar el nivel de
Control Paterno y Código de país. Consulte “Control
Paterno” (pág. 30) y “Código de país” (pág. 30).
Nota
– La contraseña predeterminada es 0000.
Control Paterno
En algunos discos de BD/DVD, existe un nivel de control para la visualización del disco en función de la edad del espectador. Puede ajustar el Control Paterno mostrado en pantalla en función del contenido del disco.
Es necesario introducir la contraseña (consulte “Cambiar
Contraseña” en pág. 30) antes de ajustar los niveles
de Control Paterno.
Después de ajustar el Control Paterno, si reproduce un disco con un nivel más alto del nivel de Control Paterno actual o si desea cambiar el nivel de Control Paterno, aparecerá un cuadro de diálogo solicitando que introduzca la contraseña.
Desactivar*, 1 a 8
Código de país
Puede ajustar el Código de país en el que vive.
Es necesario introducir la contraseña (consulte “Cambiar
Contraseña” en pág. 30) antes de ajustar el Código de país.
Este parámetro podría utilizarse para la calificación de Control Paterno y reproducción de discos.
30
Es
Red
Conexión a Internet
Defina este elemento en Permitir cuando utilice BD-Live
(pág. 25), DLNA (pág. 21) y actualice el software desde la
Permitir * , Desactivar
Información
Puede mostrar la pantalla de información de red. En esta pantalla puede ver información de Interfaz (Ethernet),
Tipo de dirección, Dirección IP, Máscara de subred,
Puerta de enlace predeterminada y DNS.
Prueba de conexión
Puede realizar una prueba de conexión a Internet. Si la
prueba falla, compruebe la “Configuración IP” (pág. 31)
y vuelva a realizar la prueba.
Configuración IP
Puede definir la Configuración IP en Auto/Manual.
Cuando se define en Auto, la dirección IP es asignada automáticamente por el sistema. Cuando se define en
Manual, la dirección IP, la máscara de subred, la puerta de enlace predeterminada y la DNS se deben ajustar manualmente.
Auto * , Manual
Conexión BD-Live
Puede definir la restricción de acceso al contenido de BD-Live.
Autorizada Permite que todos los discos de BD-Live se conecten a la red.
Permitida Permite únicamente los discos con certificación
Parcialmente * de propietario.
Prohibido Prohíbe que todos los discos de BD-Live se conecten a la red.
DLNA
Puede definir la función DLNA (pág. 21) en Permitir/
Desactivar. Cuando no utilice la función DLNA, defínala en Desactivar.
Permitir * , Desactivar
Configuración Proxy
Puede definir Configuración Proxy. Defínalo en
Desactivar para uso normal. Seleccione Permitir para definir la configuración del proxy.
Permitir Activa los ajustes del host y el puerto proxy.
Desactivar * Desactiva el servidor proxy. Seleccione esta opción cuando no utilice el servidor proxy.
Host Proxy Define el host proxy.
Puerto proxy Define el puerto proxy.
4:3
Tamaño de imagen original
MENÚ SETUP
■ Configuración de pantalla
Los ajustes predeterminados están marcados con “ * ”.
TV
Pantalla de TV
Puede ajustar la relación de aspecto de la pantalla del televisor conectado, y ajustar la salida de vídeo.
Si cambia de televisor, por ejemplo, porque ha adquirido uno nuevo, y la relación de aspecto de la pantalla del televisor conectado cambia, también tendrá que cambiar el ajuste Pantalla de TV.
16:9 Lleno Selecciónelo cuando conecte el reproductor a un televisor con pantalla 16:9. Cuando se reproduce vídeo con una relación de aspecto 4:3, el vídeo se muestra como aparece en la ilustración.
16:9 Normal * Selecciónelo cuando conecte el reproductor a un televisor con pantalla 16:9. Cuando se reproduce vídeo con una relación de aspecto 4:3, el vídeo se muestra como aparece en la ilustración.
4:3
Panorámico
4:3 Buzón
Selecciónelo cuando conecte el reproductor a un televisor con pantalla 4:3. Cuando se reproduce vídeo con una relación de aspecto 16:9, el vídeo se muestra como aparece en la ilustración.
Selecciónelo cuando conecte el reproductor a un televisor con pantalla 4:3. Cuando se reproduce vídeo con una relación de aspecto 16:9, el vídeo se muestra como aparece en la ilustración.
Tamaño de imagen original
En televisor 16:9 (pantalla panorámica)
16:9 Lleno 16:9 Normal
En televisor 4:3
4:3 Panorámico 4:3 Buzón
16:9
Resolución
Puede seleccionar la resolución de salida de vídeo entre
Auto, 480i/576i, 480p/576p, 720p, 1080i y 1080p. Cuando se define en Auto, la resolución se ajusta a la resolución máxima según el televisor conectado. Para obtener detalles adicionales sobre los formatos de salida, consulte
“Acerca de los formatos de salida de vídeo” (pág. 35).
Auto * , 480i/576i, 480p/576p, 720p, 1080i, 1080p
4
Nota
– Para emitir audio HD (como Dolby TrueHD o DTS-HD Master Audio) desde un terminal HDMI, configure Resolución como Auto o un ajuste superior a 720p.
31
Es
MENÚ SETUP
Sistema de TV
Puede seleccionar el valor de Sistema de TV entre PAL,
NTSC y Multi. Ajuste el mismo valor de Sistema de TV que su televisor. Para obtener detalles adicionales sobre
los formatos de salida, consulte “Acerca de los formatos de salida de vídeo” (pág. 35).
NTSC*, PAL,
Multi
NTSC, PAL*,
Multi
(Modelos para Corea, Taiwán y América Central y del Sur)
(Modelos para Rusia y Asia)
Color Space
Puede seleccionar la salida Color Space (pág. 40) desde
HDMI. Esta función está disponible cuando el reproductor se conecta con un cable HDMI.
RGB Permite la salida de la señal de vídeo con el rango normal de señal.
YCbCr 4:4:4 * Permite definir Color Space en YCbCr 4:4:4.
YCbCr 4:2:2 Permite definir Color Space en YCbCr 4:2:2.
Full RGB Si se ha configurado RGB y el blanco y negro de la pantalla está demasiado difuminado, seleccione este elemento. Esta opción se aplica si un componente conectado admite el intervalo RGB 0-255.
Nota
– Esta función sólo está disponible en televisores que admitan dicha función.
HDMI Deep Color
Si su televisor y/o receptor de A/V es compatible con
Deep Color (pág. 40), ajuste este elemento según su
televisor o receptor de A/V. Esta función está disponible cuando el reproductor se conecta con un cable HDMI.
30 bits, 36 bits, Desactivar *
HDMI 1080p 24Hz
Permite la salida del Vídeo BD codificado con una velocidad de fotogramas de 24 Hz en HDMI 1080p 24Hz. Con esta función es posible que disponga de una reproducción de vídeo más suave. Esta función está disponible si el receptor de A/V o el televisor admiten esta función y el reproductor está conectado con un cable HDMI. Para obtener detalles
Auto * , Desactivar
Nota
– Este parámetro está desactivado cuando la resolución de salida es diferente de 1080p.
Sincronismo de labios
Puede definir o ajustar la función Sincronismo de labios
(pág. 41). Para ajustar manualmente Sincronismo de labios,
seleccione Manual y pulse 2/3 para ajustar la cifra.
Auto * , Manual, Desactivar
Procesamiento de Video
Modo de Vídeo
Puede seleccionar Modo de Vídeo más abajo.
Estándar* La imagen es más natural y equilibrada. Este modo es adecuado para usos normales.
Rico
Cine
La imagen es más viva e intensa.
La imagen es adecuada para ver películas en una habitación a oscuras.
Particularizado Puede ajustar la imagen visual manualmente. Pulse
5/a para seleccionar el parámetro, a continuación pulse 2/3 para ajustar la figura.
Brillo
Ajusta el brillo global de la imagen.
Nitidez
Ajusta la nitidez de los elementos del vídeo.
Tonalidad
Ajusta el tono de la imagen proyectada.
Saturación
Ajusta la riqueza de color de la imagen proyectada.
Contraste
Ajusta las áreas claras (niveles blancos) de la imagen.
CTI
Suaviza los bordes de las imágenes en color.
De este modo, las imágenes en color se distinguen más.
Los valores predeterminados son 0.
Ajuste de color
Ajusta Brillo/Saturación/Tonalidad para cada color (Rojo/
Verde/Azul/Amarillo/Cian/Magenta). Para utilizar esta función, configure Modo de Vídeo como Particularizado.
Para obtener detalles sobre la configuración de elementos,
consulte “Modo de Vídeo” (pág. 32).
Los valores predeterminados son 0.
Contraste automático
Ajusta el contraste para optimizar la imagen reproducida.
Desactivar * , Activar
Reducción de ruido
Puede configurar la Reducción de ruido a un nivel entre 0 y 3. 0 equivale a desactivado y 3 es el nivel máximo.
0 * , 1, 2, 3
Modo desentrelazado
Puede seleccionar cómo detectar la señal de vídeo.
Defínalo en Auto para uso normal. Cuando aparece en la pantalla un ruido de desgarro horizontal, configure esta opción en Película/Vídeo para eliminar el ruido.
Auto * , Película, Vídeo
32
Es
■ Configuración de audio
Los ajustes predeterminados están marcados con “ * ”.
Salida de audio
Coaxial/Optica
Puede seleccionar el modo de salida de la toma COAXIAL y del terminal OPTICAL. Para obtener detalles adicionales
sobre los formatos de salida, consulte “Formatos de salida de audio” (pág. 34).
Bitstream Permite la salida de la señal digital sin ningún procesamiento. No se produce la salida del audio secundario.
PCM Permite la salida de PCM de 2 canales.
Recodificar * Permite la salida de Bitstream con audio secundario. La salida de la señal de audio se realiza como señal DTS.
Desactivar Silencia el sonido.
HDMI
Puede seleccionar el modo de salida del terminal HDMI.
Para obtener detalles sobre la configuración de elementos,
consulte “Coaxial/Optica” (pág. 33). Para obtener detalles
adicionales sobre los formatos de salida, consulte “Formatos de salida de audio” (pág. 34).
Bitstream * , PCM, Recodificar, Desactivar
MENÚ SETUP
Salida HDMI
Puede seleccionar la salida de la señal de audio desde el terminal HDMI cuando se reproduce un SA-CD.
DSD *
PCM
Emite una señal DSD en bruto. Al conectar el reproductor a un receptor A/V compatible con DSD, esta puede resultar una opción útil.
Emite una señal PCM descodificada por este reproductor.
Nota
– Para emitir audio HD (como Dolby TrueHD o DTS-HD Master Audio) desde un terminal HDMI, configure Resolución como Auto o un ajuste
Downsampling
Puede seleccionar la frecuencia de submuestreo de la señal de audio digital. Esta función está activa para la salida de señal de audio desde la toma COAXIAL/ terminal OPTICAL.
48k *
96k
192k
La tasa de muestreo más alta de la salida PCM digital es 48 kHz.
La tasa de muestreo más alta de la salida PCM digital es 96 kHz.
La tasa de muestreo más alta de la salida PCM digital es 192 kHz.
DRC
Puede activar, desactivar o poner en modo Auto el DRC
(Control de gama dinámica) (pág. 40). Cuando se define
en Auto, DRC se enciende automáticamente para una fuente con información DRC en formatoDolby TrueHD.
DRC hace que los sonidos fuertes como oclusivos suenen más bajo y que las conversaciones sean más audibles.
Resulta útil cuando se ven películas de noche.
Desactivar * , Activar, Auto
Post-procesamiento
Permite convertir la señal de audio de 2 canales en multicanal. Para realizar esta conversión, seleccione
NEO6, y seleccione el modo Cinema o Music.
Desactivar * , NEO6
Salida SACD
Prioridad SACD
Puede seleccionar un contenido reproducido desde datos multicanal o estéreo (2 canales) si se carga un SA-CD
Multi-ch * , 2-ch
Ajuste de altavoz
Configuración
Puede definir la salida de sonido envolvente de 7.1 canales dependiendo del altavoz o amplificador conectado.
1 Pulse 5/a para seleccionar el altavoz que desea configurar y, a continuación pulse ENTER.
2 Ajuste las cifras siguientes. En función del altavoz seleccionado algunos elementos no aparecen.
Tamaño Cuando la parte del altavoz de graves del altavoz mide 16 cm o más, seleccione Grande. Si es inferior a 16 cm, seleccione Pequeño.
Trim
Grande * , Pequeño
-12 a 0 dB (en pasos de 0,5 dB)
La configuración predeterminada es 0 dB.
Retraso 0,5 a 10 m (en pasos de 0,5 m)
La configuración predeterminada es 3 m.
Desactivar Cuando el altavoz seleccionado no se utiliza, seleccione Sí.
Sí, No *
3 Pulse RETURN para volver a la selección del altavoz.
Mezcla descendente 2 Canales
Puede seleccionar 2 canales analógico como método de mezcla descendente desde Estéreo o Lt/Rt.
Estéreo *
Lt/Rt
Cambia la salida del canal a estéreo, con lo que solamente se emite sonido desde los dos altavoces frontales.
Seleccione este elemento si la unidad está conectada a un descodificador Dolby Pro Logic. El sonido de los altavoces posteriores se mezcla con el sonido estéreo de 2 canales.
■ Sistema de Información
Se muestran la versión de software y la dirección MAC
4
33
Es
MENÚ SETUP
■ Formatos de salida de audio
Formato de origen
PCM 2 canales
PCM 5.1 canales
PCM 7.1 canales
HDMI COAXIAL/OPTICAL
MIXED 2CH/
Sonido envolvente de 7.1 canales
Bitstream PCM
PCM 2 canales
Recodificar Bitstream PCM
PCM 2 canales
Recodificar
PCM 5.1 canales
PCM 7.1 canales
PCM 2 canales
PCM 2 canales
2 canales
2 canales/
5.1 canales
2 canales/
7.1 canales
Dolby Digital
2 canales/
5.1 canales
Dolby Digital con AS * o SCB **
Dolby Digital
Plus con AS * o SCB **
Dolby Digital
PCM 5.1 canales
Dolby Digital Dolby Digital
Dolby Digital
Plus
PCM hasta 7.1 canales
Dolby Digital
Plus
Dolby Digital
Dolby Digital
Dolby
TrueHD
Dolby
TrueHD
PCM hasta 7.1 canales
Dolby Digital
Dolby Digital
PCM 2 canales
PCM 2 canales
Dolby
TrueHD con AS * o SCB **
PCM 2 canales
DTS con AS * o SCB **
DTS
PCM hasta 5.1 canales
DTS DTS
PCM 2 canales
DTS HD High
Resolution con AS * o SCB **
DTS-HD
Master Audio con AS * o SCB **
DTS HD High
Resolution
PCM hasta 7.1 canales
DTS HD High
Resolution
DTS
DTS-HD
Master Audio
PCM hasta 7.1 canales
DTS-HD
Master Audio
DTS
DTS
DTS
PCM 2 canales
PCM 2 canales
* “AS” es audio secundario.
** “SCB” es el sonido clic del botón, el efecto de sonido de los menús emergentes, etc.
Dolby Digital
Dolby Digital
DTS
DTS
DTS
2 canales/
7.1 canales
2 canales/
5.1 canales
2 canales/
7.1 canales
Formatos de salida SA-CD
Ajustes de salida SACD
Prioridad SACD Salida HDMI
Multi-ch
2-ch
DSD
PCM
DSD
PCM
HDMI
DSD hasta 5.1 canales
PCM hasta 5.1 canales
DSD 2 canales
PCM 2 canales
COAXIAL/OPTICAL
Sin salida
Sin salida
Sin salida
Sin salida
MIXED 2CH/7.1 canales sonido envolvente
2 canales/5.1 canales
2 canales/5.1 canales
2 canales/2 canales
2 canales/2 canales
Notas
– Para emitir audio HD (como Dolby TrueHD o DTS-HD Master Audio) desde un terminal HDMI, configure
Resolución como Auto o un ajuste superior a 720p (pág. 31).
HDMI está ajustada en PCM.
34
Es
MENÚ SETUP
■ Acerca de los formatos de salida de vídeo
Si Sistema de TV se define en NTSC
Auto 480i/576i 480p/576p Resolución
HDMI
1080p 24Hz
Reproducción de BD HDMI otros
Reproducción de DVD comercial
COMPONENT
Reproducción de BD otros
VIDEO
Reproducción de BD otros
–
Máx.
480i
480i
–
480i
480i
480i
–
480p
480p
480i
720p
–
480p
480i
1080i
–
480p
720p 60 Hz 1080i 60 Hz
480i
Activar
1080p
Desactivar
720p 60 Hz 1080i 60 Hz
1080p 24 Hz
1080p 60 Hz
1080p 60 Hz
480p desactivado 1080i 60 Hz
1080i 60 Hz desactivado
480i
480i
4
Si Sistema de TV se define en PAL
Auto 480i/576i 480p/576p
HDMI
Resolución
HDMI
1080p 24Hz
Reproducción de BD otros
Reproducción de DVD comercial
COMPONENT
Reproducción de BD otros
VIDEO
Reproducción de BD otros
–
Máx.
576i
576i
–
576i
576i
576i
–
576p
576p
576i
720p
–
576p
576i
1080i
–
576p
576i
Activar
1080p
Desactivar
720p 50 Hz 1080i 50 Hz
1080p 24 Hz
1080p 50 Hz
1080p 50 Hz
576p desactivado
576p
576p desactivado
576i
576i
Si Sistema de TV se define en Multi
Si Sistema de TV está configurado como Multi, la salida de la señal de vídeo tiene la misma frecuencia que la fuente.
Consulte las tablas anteriores para obtener información sobre la configuración de frecuencia del televisor y la resolución de la señal de vídeo de salida.
Si se muestra una pantalla de menú como, por ejemplo, SETUP la salida de la señal de vídeo tiene la misma frecuencia que el origen.
Notas
– “Máx.” en la tabla significa que la resolución se ha definido en la resolución máxima admitida por el televisor conectado.
– El parámetro HDMI 1080p 24Hz está desactivado cuando la resolución de salida es diferente de 1080p.
– Cuando el parámetro HDMI 1080p 24Hz está activado, se realiza la salida de la señal de vídeo desde HDMI durante la reproducción de BD.
– Cuando se reproduce un DVD comercial con salida de componente, la resolución máxima es 480p/576p.
– Cuando Sistema de TV se define en NTSC y el origen de vídeo no es 60 Hz, la salida de vídeo se convierte a 60 Hz.
– Cuando Sistema de TV se define en PAL y el origen de vídeo no es 50 Hz, la salida de vídeo se convierte a 50 Hz.
35
Es
ACTUALIZACIÓN DE SOFTWARE
Algunos de los discos BD recién lanzados no se pueden reproducir a menos que actualice el software del reproductor a la versión más reciente. Le recomendamos la actualización para que el reproductor funcione con el software más actual.
3 Seleccione el elemento que contiene el paquete de archivos de actualización desde Disc/USB
Storage/Network.
Para comprobar la disponibilidad de una actualización de software, visite http://download.yamaha.com/downloads/service/top/
?site=europe.yamaha.com&language=en
Consejo
– La actualización del software se inicia automáticamente tras cargar el disco que contiene el paquete de actualización.
Notas
– No saque el disco/dispositivo de memoria USB, no ponga el reproductor en modo de espera ni desenchufe el cable de alimentación o el cable LAN mientras se lleva a cabo la actualización de software.
■ Actualización del software
3.
El sistema buscará el paquete de archivos de actualización.
1.
Prepare la actualización de software.
Si actualiza el software desde Disc/USB Storage:
1 Guarde el paquete de archivos de actualización en la carpeta correspondiente en el disco/dispositivo de memoria USB. Para más información, consulte el documento de procedimientos adjunto con el paquete de archivos de actualización.
2 Cargue el disco o conecte el dispositivo de memoria USB.
Al cargar el disco, la actualización de software se inicia automáticamente. Omita el paso 2.
Si actualiza el software desde Network:
Confirme que el reproductor está conectado a la red.
2.
Seleccione el método de actualización e inicie la actualización desde el menú SETUP.
1 Pulse SETUP para mostrar la pantalla de menú
SETUP.
2 Seleccione Configuración General = Sistema =
Actualizar.
4.
Pulse ENTER para iniciar la actualización.
5.
La actualización se ha completado. El sistema se reiniciará.
36
Es
INFORMACIÓN ADICIONAL
RESOLUCIÓN DE PROBLEMAS
Consulte la tabla inferior cuando el equipo no funcione correctamente. Si el problema que usted tiene no aparece en la lista inferior o las instrucciones no le sirven de ayuda, apague este reproductor, desenchufe el cable de alimentación y póngase en contacto con un centro de servicio o concesionario Yamaha autorizado.
■ Alimentación
Problema
No hay alimentación.
La alimentación del reproductor está apagada.
■ Funcionamiento básico
Causas posibles y soluciones
– Conecte correctamente el cable de alimentación de CA.
– Pulse (p) en el panel delantero para encender la alimentación.
– La alimentación se desconectará automáticamente pasados 10 minutos continuos de inactividad (sin reproducción).
Problema
El mando a distancia no funciona.
Las teclas no funcionan.
Se ha olvidado la contraseña.
Causas posibles y soluciones
– Utilice el mando a distancia dentro de su alcance operativo. (pág. 5)
– Compruebe la configuración de ID de la unidad principal y el mando a distancia. (pág. 9)
– Mantenga pulsado p en el panel delantero durante unos 5 segundos para reiniciar el reproductor.
– Para reiniciar completamente el reproductor, desenchufe el cable de alimentación de la toma de CA durante 5 – 10 segundos, vuelva a enchufarlo y, a continuación, encienda el reproductor.
– Mantenga pulsado y en el panel delantero a la vez si no hay ningún disco insertado y con la reproducción detenida para situar el reproductor en la configuración
predeterminada (el ajuste de Seguridad (pág. 30) también se restablece).
■ Reproducción de disco
Problema
El reproductor no puede reproducir un disco.
El vídeo se para.
El reproductor hace un sonido de chasquido cuando comienza la reproducción o al cargar un disco.
Causas posibles y soluciones
– Extraiga el disco y límpielo. (pág. 4)
– Asegúrese de que se ha cargado correctamente el disco (alineado en la bandeja
portadiscos y con la cara de la etiqueta hacia arriba). (pág. 4)
– Utilice un disco admitido por el reproductor. (pág. 3)
– Extraiga el disco y compruebe si es un disco admitido por el reproductor o no. (pág. 3)
– Compruebe el código de región. (pág. 3)
– Compruebe si el disco está defectuoso probando con otro disco.
– Los discos CD-R/RW, DVD+R/RW/R DL y DVD-R/RW/R DL deben estar finalizados.
– El reproductor se parará si detecta golpes o vibraciones.
– Estos sonidos no son averías sino condiciones normales de funcionamiento del reproductor.
5
37
Es
RESOLUCIÓN DE PROBLEMAS
■ Imagen
No hay imagen.
Problema
La pantalla se congela y las teclas de operación no responden.
Causas posibles y soluciones
– Asegúrese de que los cables están correctamente conectados. (pág. 10)
– Asegúrese de que el televisor o receptor de A/V conectado está ajustado a la entrada
– Conecte el reproductor al televisor con la toma VIDEO (pág. 13) mediante el cable
de clavijas de vídeo suministrado y definiendo correctamente la Resolución. (pág. 31)
– El sistema de TV está mal ajustado. Mantenga pulsado DIMMER en el mando a distancia para restablecer la configuración predeterminada del sistema de TV.
– Pulse y, después, reinicie la reproducción.
– Desconecte la alimentación y conéctela de nuevo.
– Mantenga pulsado p en el panel delantero durante unos 5 segundos para reiniciar el reproductor.
– Ajuste la resolución deseada. (pág. 31)
La salida de vídeo no tiene la resolución deseada.
El vídeo de ancho horizontal aparece estirado verticalmente, o aparecen bandas negras en las partes superior e inferior de la pantalla. O el vídeo 4:3 aparece estirado horizontalmente.
Aparece ruido cuadrado (mosaicos) en la pantalla.
La pantalla de reproducción se perturbará si se graba vídeo DVD en una videograbadora, o se reproduce a través de una videograbadora.
No hay salida de audio o las imágenes no se reproducen adecuadamente.
– Cambie la relación de aspecto del televisor. (pág. 31)
– Se podrían ver bloques en las imágenes en escenas que contengan movimientos rápidos debido a las características de la tecnología de compresión de imagen digital.
– Este reproductor cumple con la protección contra copias analógicas. Algunos discos contienen una señal de prohibición de copia. Si intenta reproducir tales discos a través de una videograbadora, o grabar a una videograbadora y reproducir la señal, la protección contra copia impedirá la reproducción normal.
– En algunos discos en los que se ha grabado contenido protegido por derechos de autor es posible que no haya salida de audio o que las imágenes no se reproduzcan adecuadamente.
■ Sonido
Problema
No hay sonido o está distorsionado.
Causas posibles y soluciones
– Suba el volumen.
– No hay sonido durante el modo de reproducción fija, cámara lenta, avance rápido
– Compruebe que el cable de audio está correctamente conectado. (pág. 10)
– El audio puede no salir dependiendo del estado de grabación del audio, por ejemplo, cuando se haya grabado como contenido de audio, audio que no sea una señal de audio
– Compruebe la conexión de audio. (pág. 10)
Los canales de audio izquierdo y derecho están invertidos o el sonido sólo sale por uno de ellos.
No hay salida de audio o las imágenes no se reproducen adecuadamente.
– En algunos discos en los que se ha grabado contenido protegido por derechos de autor es posible que no haya salida de audio o que las imágenes no se reproduzcan adecuadamente.
– Consulte el ajuste Salida de audio y “Formatos de salida de audio”. (pág. 33, 34)
No se puede escuchar el tipo de audio que se desea y/o el número de canales.
No se escucha el sonido de PIP
(audio secundario).
– Ajuste Coaxial/Optica o HDMI en PCM/Recodificar. (pág. 33)
– Para escuchar el audio secundario, pulse 2ND AUDIO. (pág. 6)
– Dependiendo del disco, es posible que tenga que activar el audio secundario en el menú
38
Es
RESOLUCIÓN DE PROBLEMAS
■ Red
Problema
No se puede conectar a Internet.
Causas posibles y soluciones
– Conecte correctamente el cable de red.
– Encienda el equipo conectado como, por ejemplo, un módem o enrutador de banda ancha.
– Conecte correctamente el módem y/o el enrutador de banda ancha.
– Configure correctamente el valor o valores de la red. Compruebe “Red”. (pág. 31)
No se pueden descargar contenidos
BD-Live.
– Conecte correctamente el cable de red. (pág. 16)
– Conecte el dispositivo de memoria USB correctamente. Compruebe que el dispositivo
de memoria USB está conectado al puerto USB del reproductor. (pág. 16)
– Compruebe si el disco BD admite BD-Live.
– Compruebe el ajuste de “Conexión a Internet”. (pág. 31)
– Conecte el dispositivo de memoria USB formateado en FAT16 o FAT32.
– Se recomienda conectar el dispositivo de memoria USB con al menos 2 GB de espacio libre.
Si no hay suficiente espacio libre, formatee el dispositivo de memoria USB. (pág. 29)
No se puede detectar el servidor DLNA.
– Conecte correctamente el cable de red.
– Encienda el equipo conectado como, por ejemplo un enrutador de banda ancha o el servidor.
– Asegúrese de que el reproductor y el servidor están conectados al mismo punto de acceso.
– Configure correctamente el valor o valores de la red. Compruebe “Red”. (pág. 31)
– Dependiendo del servidor DLNA, es posible que sea necesario autorizar al reproductor desde el servidor.
No se puede reproducir el archivo en el servidor doméstico de red.
– Asegúrese de que el archivo se puede reproducir. (pág. 3)
– Compruebe la configuración del servidor DLNA.
– La calidad de funcionamiento y reproducción podría verse afectada por las condiciones de la red doméstica.
■ Mensajes en pantalla
– Los mensajes siguientes aparecerán en la pantalla del televisor si el disco que intenta reproducir no es apropiado o la operación no es correcta.
Mensaje de error
Not Support This File!
¡Código de región erróneo!
La red ha fallado.
Causas posibles y soluciones
– El disco tiene un código de región incompatible. Consulte “Información de gestión de la región”
– El reproductor no se puede conectar al servidor proxy. Consulte “Configuración Proxy” (pág. 31).
Red está bien, proxy ha fallado.
The Setting is prohibited, please setup again.
¡No se encuentra un fichero válido para actualización!
¡La actualización ha fallado por alguna razón!
– La conexión de BD-Live está prohibida. Consulte “Conexión BD-Live” (pág. 31).
– Compruebe si el archivo de actualización está en la carpeta apropiada.
– La actualización ha fallado. Compruebe si el archivo de actualización está dañado o es ilegible.
5
39
Es
AVCHD
AVCHD es un nuevo formato (estándar) para cámaras de vídeo de alta definición que se puede utilizar para grabar y reproducir imágenes de alta definición (HD).
BD-Live
BD-Live es un estándar de BD que utiliza una conexión de red y permite al reproductor conectarse a la red para descargar vídeos promocionales y otros datos.
BDMV
BDMV (Blu-ray Disc Movie, BD-MV=Películas en disco Blu-ray BD-MV) se refiere a uno de los formatos de aplicación utilizados para BD-ROM que constituye una de las especificaciones de los discos Blu-ray.
BDMV es un formato de grabación equivalente al Vídeo
DVD de la especificación DVD.
BONUSVIEW
Los discos compatibles con BONUSVIEW le permiten disfrutar simultáneamente de subcanal de vídeo para dos pantallas, subcanal de audio y subtítulos. Aparece una pequeña pantalla dentro de la pantalla principal durante la reproducción (Imagen en imagen).
Buzón (LB 4:3)
Un tamaño de pantalla con barras negras en las partes superior e inferior de la imagen para permitir la visualización de material en pantalla ancha (16:9) en un televisor 4:3 conectado.
Color Space
El Color Space es una gama de colores que se puede representar. RGB es un espacio de color basado en el modelo de color RGB (rojo, verde y azul) y se utiliza normalmente para monitores de PC. YCbCr es un espacio de color basado en una señal de luminancia (Y) y dos señales de diferencia de color (Cb y Cr).
Deep Color
Deep Color se refiere al uso de diversas profundidades de color en pantallas, a partir de las profundidades de 24 bits de versiones anteriores de la especificación HDMI. Esta profundidad de bits adicional permite que las pantallas
HDTV y otros tipos de pantallas pasen de millones a miles de millones de colores y eliminan la aparición de bandas de color en pantallas permitiendo unas transiciones tonales suaves y una gradación ligera entre colores. La mayor relación de contraste permite representar muchos más tonos de gris entre blanco y negro. Además Deep Color aumenta el número de colores disponibles dentro de los límites definidos por el espacio de color RGB o YCbCr.
Dirección MAC
La dirección MAC es un valor único asignado a un dispositivo de red para fines identificativos.
DivX®
DivX® es una tecnología multimedia popular creada por
DivX, Inc. Los archivos multimedia DivX® contienen vídeo muy comprimido con una alta calidad visual que mantiene un tamaño de archivo relativamente pequeño.
Los archivos DivX® también pueden incluir características multimedia avanzadas como menús, subtítulos y pistas de audio alternativas. Muchos archivos multimedia DivX® están disponibles para descarga en línea y puede crear sus propios archivos utilizando su propio contenido y herramientas fáciles de utilizar de DivX.com.
GLOSARIO
Dolby Digital
Un sistema de sonido desarrollado por Dolby Laboratories
Inc. que da un ambiente de sala de cine a la salida de audio cuando el producto está conectado con un amplificador o procesador Dolby Digital.
Dolby Digital Plus
Un sistema de sonido desarrollado como una extensión de Dolby Digital. Esta tecnología de codificación de audio soporta sonido envolvente de 7.1 multicanales.
Dolby TrueHD
Dolby TrueHD es una tecnología de codificación sin pérdidas que soporta hasta 8 canales de sonido envolvente multicanal para los discos ópticos de próxima generación.
El sonido reproducido conserva fielmente, bit a bit, la fuente original.
DRC (Control de gama dinámica)
DRC le permite ajustar la gama entre los sonidos más alto y más bajo (gama dinámica) para reproducir a un volumen intermedio. Utilícela cuando sea difícil escuchar los diálogos o durante las horas en que la reproducción pueda molestar a los vecinos.
DSD (Direct Stream Digital)
La tecnología DSD guarda señales de vídeo en soportes de almacenamiento digitales, como Super Audio CD.
Mediante DSD, las señales se guardan como valores de un solo bit en frecuencias de muestreo altas, de 2,8224 MHz, mientras que el modelado del ruido y el sobremuestreo se utilizan para reducir la distorsión, un fenómeno habitual en situaciones de alta cuantificación de señales de audio.
Debido a la elevada frecuencia de muestreo, es posible obtener una calidad de audio superior a la que ofrece el formato PCM utilizado para CD de audio normales.
DTS
Un sistema de sonido digital desarrollado por DTS, Inc. para su uso en salas de cine.
DTS-HD High Resolution Audio
DTS-HD High Resolution Audio es una nueva tecnología desarrollada para el formato de disco óptico de alta definición de próxima generación.
DTS-HD Master Audio
DTS-HD Master Audio es una tecnología de compresión de audio sin pérdidas desarrollada para el formato de disco
óptico de alta definición de próxima generación.
DTS-HD Master Audio | Essential
DTS-HD Master Audio | Essential es una tecnología de compresión de audio sin pérdidas desarrollada para el formato de disco óptico de alta definición de próxima generación.
HDMI
HDMI (High-Definition Multimedia Interface, Interfaz
Multimedia de Alta Definición) es una interfaz que soporta vídeo y audio en una sola conexión digital. La conexión HDMI lleva señales de vídeo, lo mismo estándar que de alta definición, y señales de audio en multicanal a componentes A/V, por ejemplo, televisores equipados con HDMI en forma digital y sin degradación.
40
Es
Sonido PCM lineal
PCM lineal es un formato de grabación de señales utilizado para CD de audio y en algunos discos DVD y Blu-ray. El sonido de CD de audio se graba a 44,1 kHz con 16 bits. (El sonido se graba entre 48 kHz con 16 bits y 96 kHz con 24 bits en discos DVD y entre 48 kHz con
16 bits y 192 kHz con 24 bits en discos BD.)
Sincronismo de labios
Sincronismo de labios, una abreviatura de “lip synchronization”, o sincronización de labios, es un término que hace referencia tanto a un problema habitual como a la posibilidad de mantener sincronizadas las señales de audio y vídeo durante la posproducción y la transmisión. La latencia de audio y vídeo requiere complejos ajustes por parte del usuario, pero la versión
1.3 de HDMI incorpora una función de sincronización automática de audio y vídeo que permite a los dispositivos sincronizarse de forma automática y precisa y sin la intervención del usuario.
Panorámico (PS 4:3)
Un tamaño de pantalla que recorta los costados de la imagen para permitir la visualización de material de pantalla ancha (16:9) en un televisor 4:3 conectado.
ESPECIFICACIONES
Subtítulos
Son las líneas de texto que aparecen en la parte inferior de la pantalla y que traducen o transcriben el diálogo.
Están grabadas en muchos discos de vídeo DVD y BD.
Subtítulos
La audiodescripción es un tipo de subtítulos, la diferencia entre los subtítulos y la audiodescripción es que los primeros están diseñados para personas sin problemas auditivos, mientras que los segundos lo están para personas que no oyen. Los subtítulos no suelen mostrar todo el audio. La audiodescripción muestra efectos de sonido (por ejemplo, un “suena el teléfono” y “ruido de pasos”), mientras que los subtítulos no lo hacen.
Antes de seleccionar este ajuste, asegúrese de que el disco contiene información de audiodescripción.
Menú principal
En un Vídeo BD/Vídeo DVD es el menú para seleccionar elementos tales como el capítulo que se va a reproducir y el idioma de los subtítulos. En algunos vídeos DVD, al menú principal también se le denomina
“Menú de títulos”.
x.v.Color
x.v.Color reproduce una gama de colores más amplia que antes, mostrando casi todos los colores que puede detectar el ojo humano.
5
ESPECIFICACIONES
■ Generalidades
Alimentación
[Modelos para América Central y del Sur] .....110 – 240 V CA, 50/60 Hz
[Modelos para Europa y Rusia]...................................... CA 230 V, 50 Hz
[Modelo para Asia] .........................................CA 220 – 240 V, 50/60 Hz
[Modelo para Taiwán].....................................CA 110 – 120 V, 50/60 Hz
[Modelo para Corea] ...................................................... CA 220 V, 60 Hz
Consumo de energía (normal) .............................................................. 25 W
Consumo (en espera) ........................................................................... 0,5 W
Dimensiones (Ancho × Alto × Largo) .......................... 435 × 96 × 316 mm
Peso ................................................................................................... 4,05 kg
■ Rendimiento de audio
Nivel de salida de audio (1 kHz, 0 dB, BD/DVD/CD-DA) ........... 2 ± 0,3 V
Relación señal/ruido (BD/DVD/CD-DA) ............................... 115 dB o más
Rango dinámico
BD/DVD .............................................................................. 105 dB o más
CD-DA ................................................................................. 100 dB o más
Distorsión armónica (1 kHz)
BD/DVD ....................................................................... 0,0028% o menos
CD-DA ........................................................................... 0,003 % o menos
Respuesta de frecuencia
BD/DVD ........................................... 2 Hz a 22 kHz (muestreo a 48 kHz)
2 Hz a 44 kHz (muestreo a 96 kHz)
CD-DA ................................................................................ 2 Hz a 20 kHz
■ Entrada/salida
Salida HDMI ................................................................. Conector tipo A × 1
480i/576i/480p/576p/720p/1080i/1080p/1080p@24Hz,
Soporte Deep Color, x.v. Color
Salida de vídeo componente......................................Y: 1 Vp-p (75 ohmios)
P
B
, P
R
: 0,7 Vp-p (75 ohmios)
Salida de vídeo ...............................................................1 Vp-p (75 ohmios)
Salida digital.............................................................Óptica × 1, Coaxial × 1
Salida de audio analógica ...................................................... 7.1 canales × 1
Mixed 2 canales × 1
Conectores USB ...........................................................................Tipo A × 2
Otros equipos de salida ................................................ Remote IN/OUT × 1
RS-232C × 1 (instalación personalizada),
Ethernet × 1
Las especificaciones están sujetas a cambio sin previo aviso.
41
Es
ESPECIFICACIONES
■ Propiedad intelectual
– El material audio-visual puede consistir de productos con propiedad intelectual que no se deben grabar sin la autorización del poseedor de dicha propiedad intelectual. Remítase a las leyes aplicables en su país.
– Este producto contiene tecnología de protección de copia que está protegida por patentes de los EE. UU. y otros derechos de propiedad intelectual de Rovi
Corporation. Se prohíbe la ingeniería inversa o el desarmado de la unidad.
– Fabricado bajo licencia de Dolby Laboratories.
“Dolby” y el símbolo de la doble D son marcas comerciales de Dolby Laboratories.
– Fabricado con licencia bajo las patentes de EE.UU. número: 5,451,942; 5,956,674; 5,974,380;
5,978,762; 6,226,616; 6,487,535; 7,212,872;
7,333,929; 7,392,195; 7,272,567 y otras patentes de los EE.UU. e internacionales emitidas o pendientes.
DTS y el símbolo son marcas registradas y los logotipos DTS-HD, DTS-HD Master Audio y DTS son marcas comerciales de DTS, Inc.. El producto comprende también el software. © DTS, Inc. Todos los derechos reservados.
– es una marca comercial.
– El logotipo “BD-LIVE” es una marca comercial de
Blu-ray Disc Association.
– El logotipo “BONUSVIEW” es una marca comercial de Blu-ray Disc Association.
– es una marca comercial de DVD Format/Logo
Licensing Corporation.
– HDMI, el logotipo HDMI y High-Definition
Multimedia Interface son marcas comerciales o marcas registradas de HDMI Licensing LLC.
– “x.v.Color” y el logotipo “x.v.Color” son marcas comerciales.
– “AVCHD” y el logotipo “AVCHD” son marcas comerciales de Panasonic Corporation y Sony
Corporation.
– Java y todas las marcas comerciales y logotipos basados en Java son marcas comerciales o marcas registradas de Sun Microsystems, Inc. en los Estados
Unidos y/o otros países.
– Este producto se otorga con licencia bajo la licencia de cartera de patentes AVC y la licencia de cartera de patentes VC-1 para su uso personal y no comercial por parte de un consumidor para (i) codificar vídeo que cumpla con las normas AVC y VC-1 (“AVC/VC-1 Video”) y/o (ii) descodificar vídeo AVC/VC-1 codificado por un consumidor dedicado a una actividad personal y no comercial y/o que se obtuvo de un proveedor de vídeo con licencia para proporcionar vídeo AVC/VC-1. No se otorga o se da por supuesta licencia alguna para cualquier otro uso. Se puede obtener información adicional de
MPEG LA, LLC.
Consulte http://www.mpegla.com.
– Windows Media Player es una marca comercial o una marca comercial registrada de Microsoft
Corporation en Estados Unidos y/o en otros países.
– DLNA y DLNA CERTIFIED son marcas comerciales y/o marcas de servicio de Digital Living
Network Alliance.
– “DivX®, DivX Certified®, DivX Plus™ HD y los logotipos asociados son marcas comerciales registradas de DivX, Inc. y se utilizan con licencia.”
– “DivX Certified® para reproducir vídeo DivX® y DivX Plus™ HD (H.264/.MKV) hasta 1080p HD y contenido de calidad.”
ABOUT DIVX VIDEO: DivX® es un formato de vídeo digital creado por DivX, Inc. Este equipo es un dispositivo DivX Certified® oficial que reproduce vídeo DivX. Visite divx.com para obtener más información y conseguir herramientas de software para convertir sus archivos a vídeo DivX.
ABOUT DIVX VIDEO-ON-DEMAND: este dispositivo DivX
Certified® debe registrarse para poder reproducir películas DivX
Video-on-Demand (VOD) compradas. Para obtener el código de registro, busque el apartado DivX VOD en el menú de configuración del dispositivo. Visite el sitio vod.divx.com para obtener más información sobre el proceso de registro.
42
Es
i
Information about software
This product uses the following software.
For information (copyright, etc) about each software, read the original sentences stated below.
■ About Linux, Busybox, SquashFS, LIRC, U-boot
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc.
51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public License is intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This General Public License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free
Software Foundation software is covered by the GNU Library General Public License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General
Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary. To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the
Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components
(compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.
GNU GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND
MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General
Public License. The “Program”, below, refers to any such program or work, and a
“work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language.
(Hereinafter, translation is included without limitation in the term “modification”.)
Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this
License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program).
Whether that is true depends on what the Program does.
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this
License. Therefore, by modifying or distributing the Program (or any work based on the Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.
1. You may copy and distribute verbatim copies of the Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this
License.
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License.
c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you
(whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the
General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free
Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free
Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO
WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE
PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED
TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER
PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS
PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING
ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE
PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA
BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR
THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH
ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the public, the best way to achieve this is to make it free software which everyone can redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found.
<one line to give the program’s name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software
Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public
License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc., 51 Franklin St,
Fifth Floor, Boston, MA 02110-1301 USA
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it starts in an interactive mode:
Gnomovision version 69, Copyright (C) year name of author Gnomovision comes with ABSOLUTELY NO WARRANTY; for details type ‘show w’. This is free software, and you are welcome to redistribute it under certain conditions; type
‘show c’ for details.
The hypothetical commands ‘show w’ and ‘show c’ should show the appropriate parts of the General Public License. Of course, the commands you use may be called something other than ‘show w’ and ‘show c’; they could even be mouse-clicks or menu items--whatever suits your program.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the program, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program
‘Gnomovision’ (which makes passes at compilers) written by James Hacker.
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into proprietary programs. If your program is a subroutine library, you may consider it more useful to permit linking proprietary applications with the library. If this is what you want to do, use the GNU Library General
Public License instead of this License..
■ About glibc, libmtp, libusb, libusb-compat, DirectFB
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc.
59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.
This license, the Lesser General Public License, applies to some specially designated software packages--typically libraries--of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not price. Our
General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/or modify the library.
To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be affected by problems that might be introduced by others.
Finally, software patents pose a constant threat to the existence of any free program.
We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license.
Most GNU software, including some libraries, is covered by the ordinary GNU General
Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public
License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.
When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General Public License permits more lax criteria for linking other code with the library.
We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.
For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library. A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser
General Public License.
In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library.
The precise terms and conditions for copying, distribution and modification follow.
Pay close attention to the difference between a “work based on the library” and a “work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the library in order to run.
ii
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND
MODIFICATION
0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called “this License”). Each licensee is addressed as “you”.
A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables.
The “Library”, below, refers to any such software library or work which has been distributed under these terms. A “work based on the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing the
Library or a portion of it, either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term “modification”.)
“Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library.
Activities other than copying, distribution and modification are not covered by this
License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does.
1. You may copy and distribute verbatim copies of the Library’s complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.
c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library.
In addition, mere aggregation of another work not based on the Library with the Library
(or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General
Public License, version 2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary
GNU General Public License applies to all subsequent copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion or derivative of it, under
Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you accompany it with the complete corresponding machinereadable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange.
If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.
5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.
However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because it contains portions of the Library), rather than a “work that uses the library”. The executable is therefore covered by this License.
Section 6 states terms for distribution of such executables.
When a “work that uses the Library” uses material from a header file that is part of the
Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.
6. As an exception to the Sections above, you may also combine or link a ‘work that uses the Library” with the Library to produce a work containing portions of the
Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer’s own use and reverse engineering for debugging such modifications.
You must give prominent notice with each copy of the work that the Library is used in it and that the Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this License. Also, you must do one of these things: a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in the work
(which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable “work that uses the Library”, as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the Library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that (1) uses at run time a copy of the library already present on the user’s computer system, rather than copying library functions into the executable, and (2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interfacecompatible with the version that the work was made with.
c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.
d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place.
e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.
For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components
(compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system. Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.
7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the Library and of the other library facilities is otherwise permitted, and provided that you do these two things: a) Accompany the combined library with a copy of the same work based on the
Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above.
b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
iii
9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this
License. Therefore, by modifying or distributing the Library (or any work based on the Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.
10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions.
You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this License.
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you
(whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License.
12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
13. The Free Software Foundation may publish revised and/or new versions of the
Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number. If the Library specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free
Software Foundation.
14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this.
Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO
WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE
LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE
LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED
TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER
PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS
PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING
ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE
LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA
BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR
THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH
ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License).
To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source file to most effectively convey the exclusion of warranty; and each file should have at least the “copyright” line and a pointer to where the full notice is found.
<one line to give the library’s name and a brief idea of what it does.> Copyright (C)
<year> <name of author>
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software
Foundation; either version 2 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public
License for more details.
You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 59 Temple
Place, Suite 330, Boston, MA 02111-1307 USA
Also add information on how to contact you by electronic and paper mail.
You should also get your employer (if you work as a programmer) or your school, if any, to sign a “copyright disclaimer” for the library, if necessary. Here is a sample; alter the names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the library ‘Frob’ (a library for tweaking knobs) written by James Random Hacker.
<signature of Ty Coon>, 1 April 1990 Ty Coon, President of Vice
That’s all there is to it!
■ About Fusion
DirectFB Fusion kernel module: introduction and API by Niels Roest
Copyright (C) 2009 Niels Roest
This documentation is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
General Public License for more details.
You should have received a copy of the GNU General Public License along with this program; if not, write to the Free Software Foundation, Inc.,
59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
For more details see the ?le COPYING in the source distribution of Linux.
■ About openssl
Copyright (C) 1998-2008 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgment:
“This product includes software developed by the OpenSSL Project for use in the
OpenSSL Toolkit. (http://www.openssl.org/)”
4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact [email protected].
5. Products derived from this software may not be called “OpenSSL” nor may
“OpenSSL” appear in their names without prior written permission of the OpenSSL
Project.
6. Redistributions of any form whatsoever must retain the following acknowledgment:
‘This product includes software developed by the OpenSSL Project for use in the
OpenSSL Toolkit (http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT “AS IS” AND ANY
EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF
LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF
THE USE OF THIS SOFTWARE, EVEN IF ADVISEDOF THE POSSIBILITY OF
SUCH DAMAGE.
This product includes cryptographic software written by Eric Young
([email protected]). This product includes software written by Tim Hudson
iv
Original SSLeay License
Copyright (C) 1995-1998 Eric Young ([email protected]) All rights reserved.
This package is an SSL implementation written by Eric Young ([email protected]).
The implementation was written so as to conform with Netscapes SSL.
This library is free for commercial and non-commercial use as long as the following conditions are aheared to. The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The
SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson ([email protected]).
Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed. If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgement:
“This product includes cryptographic software written by Eric Young
([email protected])” The word ‘cryptographic’ can be left out if the rouines from the library being used are not cryptographic related :-).
4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement:
“This product includes software written by Tim Hudson ([email protected])”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG “AS IS” AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
The licence and distribution terms for any publically available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution licence [including the GNU Public Licence.]
■ About zlib
Copyright notice:
(C) 1995-2004 Jean-loup Gailly and Mark Adler
This software is provided ‘as-is’, without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software.
Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.
Jean-loup Gailly Mark Adler [email protected] [email protected]
If you use the zlib library in a product, we would appreciate *not* receiving lengthy legal documents to sign. The sources are provided for free but without warranty of any kind. The library has been entirely written by Jean-loup Gailly and Mark Adler; it does not include third-party code.
If you redistribute modified sources, we would appreciate that you include in the file
ChangeLog history information documenting your changes. Please read the FAQ for more information on the distribution of modified source versions.
■ About FreeType
The FreeType Project LICENSE
2006-Jan-27
Copyright 1996-2002, 2006 by
David Turner, Robert Wilhelm, and Werner Lemberg
Introduction
The FreeType Project is distributed in several archive packages; some of them may contain, in addition to the FreeType font engine, various tools and contributions which rely on, or relate to, the FreeType Project.
This license applies to all files found in such packages, and which do not fall under their own explicit license. The license affects thus the FreeType font engine, the test programs, documentation and makefiles, at the very least.
This license was inspired by the BSD, Artistic, and IJG (Independent JPEG Group) licenses, which all encourage inclusion and use of free software in commercial and freeware products alike. As a consequence, its main points are that: o We don’t promise that this software works. However, we will be interested in any kind of bug reports. (‘as is’ distribution) o You can use this software for whatever you want, in parts or full form, without having to pay us. (‘royalty-free’ usage) o You may not pretend that you wrote this software. If you use it, or only parts of it, in a program, you must acknowledge somewhere in your documentation that you have used the FreeType code. (‘credits’)
We specifically permit and encourage the inclusion of this software, with or without modifications, in commercial products. We disclaim all warranties covering The
FreeType Project and assume no liability related to The FreeType Project.
Finally, many people asked us for a preferred form for a credit/disclaimer to use in compliance with this license. We thus encourage you to use the following text:
Portions of this software are copyright (C) <year> The FreeType Project
(www.freetype.org). All rights reserved.
Please replace <year> with the value from the FreeType version you actually use.
Legal Terms
0. Definitions
Throughout this license, the terms ‘package’, ‘FreeType Project’, and ‘FreeType archive’ refer to the set of files originally distributed by the authors (David Turner,
Robert Wilhelm, and Werner Lemberg) as the ‘FreeType Project’, be they named as alpha, beta or final release.
‘You’ refers to the licensee, or person using the project, where ‘using’ is a generic term including compiling the project’s source code as well as linking it to form a ‘program’ or ‘executable’. This program is referred to as ‘a program using the FreeType engine’.
This license applies to all files distributed in the original FreeType Project, including all source code, binaries and documentation, unless otherwise stated in the file in its original, unmodified form as distributed in the original archive. If you are unsure whether or not a particular file is covered by this license, you must contact us to verify this.
The FreeType Project is copyright (C) 1996-2000 by David Turner, Robert Wilhelm, and Werner Lemberg. All rights reserved except as specified below.
1. No Warranty
THE FREETYPE PROJECT IS PROVIDED ‘AS IS’ WITHOUT WARRANTY OF
ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED
TO, WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. IN NO EVENT WILL ANY OF THE AUTHORS OR
COPYRIGHT HOLDERS BE LIABLE FOR ANY DAMAGES CAUSED BY THE
USE OR THE INABILITY TO USE, OF THE FREETYPE PROJECT.
2. Redistribution
This license grants a worldwide, royalty-free, perpetual and irrevocable right and license to use, execute, perform, compile, display, copy, create derivative works of, distribute and sublicense the FreeType Project (in both source and object code forms) and derivative works thereof for any purpose; and to authorize others to exercise some or all of the rights granted herein, subject to the following conditions: o Redistribution of source code must retain this license file (‘FTL.TXT’) unaltered; any additions, deletions or changes to the original files must be clearly indicated in accompanying documentation. The copyright notices of the unaltered, original files must be preserved in all copies of source files.
o Redistribution in binary form must provide a disclaimer that states that the software is based in part of the work of the FreeType Team, in the distribution documentation.
We also encourage you to put an URL to the FreeType web page in your documentation, though this isn’t mandatory.
These conditions apply to any software derived from or based on the FreeType Project, not just the unmodified files. If you use our work, you must acknowledge us. However, no fee need be paid to us.
3. Advertising
Neither the FreeType authors and contributors nor you shall use the name of the other for commercial, advertising, or promotional purposes without specific prior written permission.
We suggest, but do not require, that you use one or more of the following phrases to refer to this software in your documentation or advertising materials: ‘FreeType
Project’, ‘FreeType Engine’, ‘FreeType library’, or ‘FreeType Distribution’.
As you have not signed this license, you are not required to accept it. However, as the
FreeType Project is copyrighted material, only this license, or another one contracted with the authors, grants you the right to use, distribute, and modify it. Therefore, by using, distributing, or modifying the FreeType Project, you indicate that you understand and accept all the terms of this license.
4. Contacts
There are two mailing lists related to FreeType: o [email protected]
Discusses general use and applications of FreeType, as well as future and wanted additions to the library and distribution. If you are looking for support, start in this list if you haven’t found anything to help you in the documentation.
Discusses bugs, as well as engine internals, design issues, specific licenses, porting, etc.
Our home page can be found at http://www.freetype.org
v
■ About Expat
Copyright (C) 1998, 1999, 2000 Thai Open Source Software Center Ltd and Clark Cooper
Copyright (C) 2001, 2002, 2003, 2004, 2005, 2006 Expat maintainers.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions:
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS
OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR
OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR
OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
■ About cURL
COPYRIGHT AND PERMISSION NOTICE
Copyright (C) 1996 - 2009, Daniel Stenberg, <[email protected]>.
All rights reserved.
Permission to use, copy, modify, and distribute this software for any purpose with or without fee is hereby granted, provided that the above copyright notice and this permission notice appear in all copies.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO
EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR
ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION
OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
THE SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Software without prior written authorization of the copyright holder.
■ About Independent JPEG group
The Independent JPEG Group’s JPEG software
README for release 7 of 27-Jun-2009
This distribution contains the seventh public release of the Independent JPEG Group’s free JPEG software. You are welcome to redistribute this software and to use it for any purpose, subject to the conditions under LEGAL ISSUES, below.
This software is the work of Tom Lane, Guido Vollbeding, Philip Gladstone, Bill
Allombert, Jim Boucher, Lee Crocker, Bob Friesenhahn, Ben Jackson, Julian
Minguillon, Luis Ortiz, George Phillips, Davide Rossi, Ge’ Weijers, and other members of the Independent JPEG Group.
IJG is not affiliated with the official ISO JPEG standards committee.
DOCUMENTATION ROADMAP
This file contains the following sections:
OVERVIEW
LEGAL ISSUES
General description of JPEG and the IJG software.
Copyright, lack of warranty, terms of distribution.
REFERENCES
ARCHIVE LOCATIONS
ACKNOWLEDGMENTS
FILE FORMAT WARS
Where to learn more about JPEG.
Where to find newer versions of this software.
Special thanks.
Software *not* to get.
TO DO Plans for future IJG releases.
Other documentation files in the distribution are:
User documentation: install.txt
usage.txt
How to configure and install the IJG software.
Usage instructions for cjpeg, djpeg, jpegtran, rdjpgcom, and wrjpgcom.
*.1
wizard.txt
Unix-style man pages for programs (same info as usage.txt).
Advanced usage instructions for JPEG wizards only.
change.log
Version-to-version change highlights.
Programmer and internal documentation: libjpeg.txt
example.c
How to use the JPEG library in your own programs.
Sample code for calling the JPEG library.
structure.txt
Overview of the JPEG library’s internal structure.
filelist.txt
Road map of IJG files.
coderules.txt
Coding style rules --- please read if you contribute code.
Please read at least the files install.txt and usage.txt. Some information can also be found in the JPEG FAQ (Frequently Asked Questions) article. See ARCHIVE
LOCATIONS below to find out where to obtain the FAQ article.
If you want to understand how the JPEG code works, we suggest reading one or more of the REFERENCES, then looking at the documentation files (in roughly the order listed) before diving into the code.
OVERVIEW
This package contains C software to implement JPEG image encoding, decoding, and transcoding. JPEG (pronounced “jay-peg”) is a standardized compression method for full-color and gray-scale images.
This software implements JPEG baseline, extended-sequential, and progressive compression processes. Provision is made for supporting all variants of these processes, although some uncommon parameter settings aren’t implemented yet. We have made no provision for supporting the hierarchical or lossless processes defined in the standard.
We provide a set of library routines for reading and writing JPEG image files, plus two sample applications “cjpeg” and “djpeg”, which use the library to perform conversion between JPEG and some other popular image file formats. The library is intended to be reused in other applications.
In order to support file conversion and viewing software, we have included considerable functionality beyond the bare JPEG coding/decoding capability; for example, the color quantization modules are not strictly part of JPEG decoding, but they are essential for output to colormapped file formats or colormapped displays.
These extra functions can be compiled out of the library if not required for a particular application.
We have also included “jpegtran”, a utility for lossless transcoding between different
JPEG processes, and “rdjpgcom” and “wrjpgcom”, two simple applications for inserting and extracting textual comments in JFIF files.
The emphasis in designing this software has been on achieving portability and flexibility, while also making it fast enough to be useful. In particular, the software is not intended to be read as a tutorial on JPEG. (See the REFERENCES section for introductory material.) Rather, it is intended to be reliable, portable, industrial-strength code. We do not claim to have achieved that goal in every aspect of the software, but we strive for it.
We welcome the use of this software as a component of commercial products. No royalty is required, but we do ask for an acknowledgement in product documentation, as described under LEGAL ISSUES.
LEGAL ISSUES
In plain English:
1. We don’t promise that this software works. (But if you find any bugs, please let us know!)
2. You can use this software for whatever you want. You don’t have to pay us.
3. You may not pretend that you wrote this software. If you use it in a program, you must acknowledge somewhere in your documentation that you’ve used the IJG code.
In legalese:
The authors make NO WARRANTY or representation, either express or implied, with respect to this software, its quality, accuracy, merchantability, or fitness for a particular purpose. This software is provided “AS IS”, and you, its user, assume the entire risk as to its quality and accuracy.
This software is copyright (C) 1991-2009, Thomas G. Lane, Guido Vollbeding.
All Rights Reserved except as specified below.
Permission is hereby granted to use, copy, modify, and distribute this software (or portions thereof) for any purpose, without fee, subject to these conditions:
(1) If any part of the source code for this software is distributed, then this README file must be included, with this copyright and no-warranty notice unaltered; and any additions, deletions, or changes to the original files must be clearly indicated in accompanying documentation.
(2) If only executable code is distributed, then the accompanying documentation must state that “this software is based in part on the work of the Independent JPEG Group”.
(3) Permission for use of this software is granted only if the user accepts full responsibility for any undesirable consequences; the authors accept NO LIABILITY for damages of any kind.
These conditions apply to any software derived from or based on the IJG code, not just to the unmodified library. If you use our work, you ought to acknowledge us.
Permission is NOT granted for the use of any IJG author’s name or company name in advertising or publicity relating to this software or products derived from it. This software may be referred to only as “the Independent JPEG Group’s software”.
We specifically permit and encourage the use of this software as the basis of commercial products, provided that all warranty or liability claims are assumed by the product vendor.
ansi2knr.c is included in this distribution by permission of L. Peter Deutsch, sole proprietor of its copyright holder, Aladdin Enterprises of Menlo Park, CA. ansi2knr.c is
NOT covered by the above copyright and conditions, but instead by the usual distribution terms of the Free Software Foundation; principally, that you must include source code if you redistribute it. (See the file ansi2knr.c for full details.) However, since ansi2knr.c is not needed as part of any program generated from the IJG code, this does not limit you more than the foregoing paragraphs do.
The Unix configuration script “configure” was produced with GNU Autoconf. It is copyright by the Free Software Foundation but is freely distributable. The same holds for its supporting scripts (config.guess, config.sub, ltmain.sh). Another support script, install-sh, is copyright by X Consortium but is also freely distributable.
The IJG distribution formerly included code to read and write GIF files. To avoid entanglement with the Unisys LZW patent, GIF reading support has been removed altogether, and the GIF writer has been simplified to produce “uncompressed GIFs”.
This technique does not use the LZW algorithm; the resulting GIF files are larger than usual, but are readable by all standard GIF decoders.
We are required to state that
“The Graphics Interchange Format(c) is the Copyright property of
CompuServe Incorporated. GIF(sm) is a Service Mark property of
CompuServe Incorporated.”
REFERENCES
We recommend reading one or more of these references before trying to understand the innards of the JPEG software.
The best short technical introduction to the JPEG compression algorithm is
Wallace, Gregory K. “The JPEG Still Picture Compression Standard”, vi
Communications of the ACM, April 1991 (vol. 34 no. 4), pp. 30-44.
(Adjacent articles in that issue discuss MPEG motion picture compression, applications of JPEG, and related topics.) If you don’t have the CACM issue handy, a PostScript file containing a revised version of Wallace’s article is available at http://www.ijg.org/files/ wallace.ps.gz. The file (actually a preprint for an article that appeared in IEEE Trans.
Consumer Electronics) omits the sample images that appeared in CACM, but it includes corrections and some added material. Note: the Wallace article is copyright
ACM and IEEE, and it may not be used for commercial purposes.
A somewhat less technical, more leisurely introduction to JPEG can be found in “The
Data Compression Book” by Mark Nelson and Jean-loup Gailly, published by M&T
Books (New York), 2nd ed. 1996, ISBN 1-55851-434-1. This book provides good explanations and example C code for a multitude of compression methods including
JPEG. It is an excellent source if you are comfortable reading C code but don’t know much about data compression in general. The book’s JPEG sample code is far from industrial-strength, but when you are ready to look at a full implementation, you’ve got one here...
The best currently available description of JPEG is the textbook “JPEG Still Image
Data Compression Standard” by William B. Pennebaker and Joan L. Mitchell, published by Van Nostrand Reinhold, 1993, ISBN 0-442-01272-1. Price US$59.95,
638 pp. The book includes the complete text of the ISO JPEG standards (DIS 10918-1 and draft DIS 10918-2).
Although this is by far the most detailed and comprehensive exposition of JPEG publicly available, we point out that it is still missing an explanation of the most essential properties and algorithms of the underlying DCT technology.
If you think that you know about DCT-based JPEG after reading this book, then you are in delusion. The real fundamentals and corresponding potential of DCT-based JPEG are not publicly known so far, and that is the reason for all the mistaken developments taking place in the image coding domain.
The original JPEG standard is divided into two parts, Part 1 being the actual specification, while Part 2 covers compliance testing methods. Part 1 is titled “Digital
Compression and Coding of Continuous-tone Still Images, Part 1: Requirements and guidelines” and has document numbers ISO/IEC IS 10918-1, ITU-T T.81. Part 2 is titled “Digital Compression and Coding of Continuous-tone Still Images, Part 2:
Compliance testing” and has document numbers ISO/IEC IS 10918-2, ITU-T T.83.
The JPEG standard does not specify all details of an interchangeable file format. For the omitted details we follow the “JFIF” conventions, revision 1.02. A copy of the JFIF spec is available from:
Literature Department
C-Cube Microsystems, Inc.
1778 McCarthy Blvd.
Milpitas, CA 95035 phone (408) 944-6300, fax (408) 944-6314
A PostScript version of this document is available at http://www.ijg.org/files/jfif.ps.gz.
There is also a plain text version at http://www.ijg.org/files/jfif.txt.gz, but it is missing the figures.
The TIFF 6.0 file format specification can be obtained by FTP from ftp://ftp.sgi.com/ graphics/tiff/TIFF6.ps.gz. The JPEG incorporation scheme found in the TIFF 6.0 spec of 3-June-92 has a number of serious problems. IJG does not recommend use of the
TIFF 6.0 design (TIFF Compression tag 6). Instead, we recommend the JPEG design proposed by TIFF Technical Note #2 (Compression tag 7). Copies of this Note can be obtained from http://www.ijg.org/files/. It is expected that the next revision of the TIFF spec will replace the 6.0 JPEG design with the Note’s design. Although IJG’s own code does not support TIFF/JPEG, the free libtiff library uses our library to implement TIFF/
JPEG per the Note.
ARCHIVE LOCATIONS
The “official” archive site for this software is www.ijg.org. The most recent released version can always be found there in directory “files”. This particular version will be archived as http://www.ijg.org/files/jpegsrc.v7.tar.gz, and in Windows-compatible
“zip” archive format as http://www.ijg.org/files/jpegsr7.zip.
The JPEG FAQ (Frequently Asked Questions) article is a source of some general information about JPEG. It is available on the World Wide Web at http://www.faqs.org/ faqs/jpeg-faq/ and other news.answers archive sites, including the official news.answers archive at rtfm.mit.edu: ftp://rtfm.mit.edu/pub/usenet/news.answers/ jpeg-faq/. If you don’t have Web or FTP access, send e-mail to [email protected] with body send usenet/news.answers/jpeg-faq/part1 send usenet/news.answers/jpeg-faq/part2
ACKNOWLEDGMENTS
Thank to Juergen Bruder of the Georg-Cantor-Organization at the Martin-Luther-
University Halle for providing me with a copy of the common DCT algorithm article, only to find out that I had come to the same result in a more direct and comprehensible way with a more generative approach.
Thank to Istvan Sebestyen and Joan L. Mitchell for inviting me to the ITU JPEG (Study
Group 16) meeting in Geneva, Switzerland.
Thank to Thomas Wiegand and Gary Sullivan for inviting me to the Joint Video Team
(MPEG & ITU) meeting in Geneva, Switzerland.
Thank to John Korejwa and Massimo Ballerini for inviting me to fruitful consultations in Boston, MA and Milan, Italy.
Thank to Hendrik Elstner, Roland Fassauer, and Simone Zuck for corresponding business development.
Thank to Nico Zschach and Dirk Stelling of the technical support team at the Digital
Images company in Halle for providing me with extra equipment for configuration tests.
Thank to Richard F. Lyon (then of Foveon Inc.) for fruitful communication about JPEG configuration in Sigma Photo Pro software.
Last but not least special thank to Thomas G. Lane for the original design and development of this singular software package.
FILE FORMAT WARS
The ISO JPEG standards committee actually promotes different formats like JPEG-
2000 or JPEG-XR which are incompatible with original DCT-based JPEG and which are based on faulty technologies. IJG therefore does not and will not support such momentary mistakes (see REFERENCES). We have little or no sympathy for the promotion of these formats. Indeed, one of the original reasons for developing this free software was to help force convergence on common, interoperable format standards for
JPEG files. Don’t use an incompatible file format! (In any case, our decoder will remain capable of reading existing JPEG image files indefinitely.)
TO DO v7 is basically just a necessary interim release, paving the way for a major breakthrough in image coding technology with the next v8 package which is scheduled for release in the year 2010.
Please send bug reports, offers of help, etc. to [email protected].
■ About International Components for Unicode
ICU License - ICU 1.8.1 and later
COPYRIGHT AND PERMISSION NOTICE
Copyright (C) 1995-2003 International Business Machines Corporation and others
All rights reserved.
Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the “Software”), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, provided that the above copyright notice(s) and this permission notice appear in all copies of the Software and that both the above copyright notice(s) and this permission notice appear in supporting documentation.
THE SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY
KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT OF THIRD PARTY RIGHTS. IN NO
EVENT SHALL THE COPYRIGHT HOLDER OR HOLDERS INCLUDED IN THIS
NOTICE BE LIABLE FOR ANY CLAIM, OR ANY SPECIAL INDIRECT OR
CONSEQUENTIAL DAMAGES, OR ANY DAMAGES WHATSOEVER
RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION,
ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE
OF THIS SOFTWARE.
Except as contained in this notice, the name of a copyright holder shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Software without prior written authorization of the copyright holder.
All trademarks and registered trademarks mentioned herein are the property of their respective owners.
■ About libpng
This copy of the libpng notices is provided for your convenience. In case of any discrepancy between this copy and the notices in the file png.h that is included in the libpng distribution, the latter shall prevail.
COPYRIGHT NOTICE, DISCLAIMER, and LICENSE:
If you modify libpng you may insert additional notices immediately following this sentence.
libpng versions 1.2.6, August 15, 2004, through 1.2.35, February 14, 2009, are
Copyright (C) 2004, 2006-2008 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.2.5 with the following individual added to the list of Contributing Authors
Cosmin Truta libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright
(C) 2000-2002 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-1.0.6 with the following individuals added to the list of Contributing Authors
Simon-Pierre Cadieux
Eric S. Raymond
Gilles Vollant and with the following additions to the disclaimer:
There is no warranty against interference with your enjoyment of the library or against infringement. There is no warranty that our efforts or the library will fulfill any of your particular purposes or needs. This library is provided with all faults, and the entire risk of satisfactory quality, performance, accuracy, and effort is with the user.
libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright (C)
1998, 1999 Glenn Randers-Pehrson, and are distributed according to the same disclaimer and license as libpng-0.96, with the following individuals added to the list of
Contributing Authors:
Tom Lane
Glenn Randers-Pehrson
Willem van Schaik libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (C) 1996, 1997
Andreas Dilger Distributed according to the same disclaimer and license as libpng-0.88, with the following individuals added to the list of Contributing Authors:
John Bowler
Kevin Bracey
Sam Bushell
Magnus Holmgren vii
Greg Roelofs
Tom Tanner libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (C) 1995,
1996 Guy Eric Schalnat, Group 42, Inc.
For the purposes of this copyright and license, “Contributing Authors” is defined as the following set of individuals:
Andreas Dilger
Dave Martindale
Guy Eric Schalnat
Paul Schmidt
Tim Wegner
The PNG Reference Library is supplied “AS IS”. The Contributing Authors and Group
42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the warranties of merchantability and of fitness for any purpose. The Contributing Authors and Group 42, Inc. assume no liability for direct, indirect, incidental, special, exemplary, or consequential damages, which may result from the use of the PNG
Reference Library, even if advised of the possibility of such damage.
Permission is hereby granted to use, copy, modify, and distribute this source code, or portions hereof, for any purpose, without fee, subject to the following restrictions:
1. The origin of this source code must not be misrepresented.
2. Altered versions must be plainly marked as such and must not be misrepresented as being the original source.
3. This Copyright notice may not be removed or altered from any source or altered source distribution.
The Contributing Authors and Group 42, Inc. specifically permit, without fee, and encourage the use of this source code as a component to supporting the PNG file format in commercial products. If you use this source code in a product, acknowledgment is not required but would be appreciated.
A “png_get_copyright” function is available, for convenient use in “about” boxes and the like: printf(“%s”,png_get_copyright(NULL));
Also, the PNG logo (in PNG format, of course) is supplied in the files “pngbar.png” and
“pngbar.jpg (88x31) and “pngnow.png” (98x31).
Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a certification mark of the Open Source Initiative.
Glenn Randers-Pehrson glennrp at users.sourceforge.net
February 14, 2009
■ About tinyxml www.sourceforge.net/projects/tinyxml
Original code (2.0 and earlier )copyright (C) 2000-2006 Lee Thomason
(www.grinninglizard.com)
This software is provided ‘as-is’, without any express or implied warranty. In no event will the authors be held liable for any damages arising from the use of this software.
Permission is granted to anyone to use this software for any purpose, including commercial applications, and to alter it and redistribute it freely, subject to the following restrictions:
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required.
2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.
■ About dtoa and strtod
The author of this software is David M. Gay.
Copyright (C) 1991, 2000, 2001 by Lucent Technologies.
Permission to use, copy, modify, and distribute this software for any purpose without fee is hereby granted, provided that this entire notice is included in all copies of any software which is or includes a copy or modification of this software and in all copies of the supporting documentation for such software.
THIS SOFTWARE IS BEING PROVIDED “AS IS”, WITHOUT ANY EXPRESS OR
IMPLIED WARRANTY. IN PARTICULAR, NEITHER THE AUTHOR NOR
LUCENT MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND
CONCERNING THE MERCHANTABILITY OF THIS SOFTWARE OR ITS
FITNESS FOR ANY PARTICULAR PURPOSE.
■ About gSOAP gSOAP Public License
Version 1.3b
The gSOAP public license is derived from the Mozilla Public License (MPL1.1). The sections that were deleted from the original MPL1.1 text are 1.0.1, 2.1.(c),(d), 2.2.(c),(d), 8.2.(b), 10, and 11.
Section 3.8 was added. The modified sections are 2.1.(b), 2.2.(b), 3.2 (simplified), 3.5 (deleted the last sentence), and 3.6 (simplified).
This license applies to the gSOAP software package, with the exception of the wsdl2h source code located in gsoap/wsdl, all code generated by wsdl2h, the UDDI source code gsoap/uddi2, and the
Web server sample source code samples/webserver. To use all of the software commercially, a commercial license has to be obtained from www.genivia.com.
1 DEFINITIONS.
1.0.1.
1.1. “Contributor” means each entity that creates or contributes to the creation of
Modifications.
1.2. “Contributor Version” means the combination of the Original Code, prior
Modifications used by a Contributor, and the Modifications made by that particular
Contributor.
1.3. “Covered Code” means the Original Code, or Modifications or the combination of the Original Code, and Modifications, in each case including portions thereof.
1.4. “Electronic Distribution Mechanism” means a mechanism generally accepted in the software development community for the electronic transfer of data.
1.5. “Executable” means Covered Code in any form other than Source Code.
1.6. “Initial Developer” means the individual or entity identified as the Initial
Developer in the Source Code notice required by Exhibit A.
1.7. “Larger Work” means a work which combines Covered Code or portions thereof with code not governed by the terms of this License.
1.8. “License” means this document.
1.8.1. “Licensable” means having the right to grant, to the maximum extent possible, whether at the time of the initial grant or subsequently acquired, any and all of the rights conveyed herein.
1.9. “Modifications” means any addition to or deletion from the substance or structure of either the Original Code or any previous Modifications. When Covered Code is released as a series of files, a Modification is: A.
Any addition to or deletion from the contents of a file containing Original Code or previous Modifications. B.
Any new file that contains any part of the Original Code, or previous Modifications.
1.10. “Original Code” means Source Code of computer software code which is described in the Source Code notice required by Exhibit A as Original Code, and which, at the time of its release under this License is not already Covered Code governed by this License.
1.10.1. “Patent Claims” means any patent claim(s), now owned or hereafter acquired, including without limitation, method, process, and apparatus claims, in any patent
Licensable by grantor.
http://www.cs.fsu.edu/~engelen/license.html
1.11. “Source Code” means the preferred form of the Covered Code for making modifications to it, including all modules it contains, plus any associated interface definition files, scripts used to control compilation and installation of an Executable, or source code differential comparisons against either the Original Code or another well known, available Covered Code of the Contributor’s choice. The Source Code can be in a compressed or archival form, provided the appropriate decompression or de-archiving software is widely available for no charge.
1.12. “You” (or “Your”) means an individual or a legal entity exercising rights under, and complying with all of the terms of, this License or a future version of this License issued under Section 6.1. For legal entities, “You” includes any entity which controls, is controlled by, or is under common control with You. For purposes of this definition,
“control” means (a) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (b) ownership of more than fifty percent (50%) of the outstanding shares or beneficial ownership of such entity.
2 SOURCE CODE LICENSE.
2.1. The Initial Developer Grant. The Initial Developer hereby grants You a worldwide, royalty-free, non-exclusive license, subject to third party intellectual property claims:
(a) under intellectual property rights (other than patent or trademark) Licensable by Initial
Developer to use, reproduce, modify, display, perform, sublicense and distribute the
Original Code (or portions thereof) with or without Modifications, and/or as part of a
Larger Work; and
(b) under patents now or hereafter owned or controlled by Initial Developer, to make, have made, use and sell (“offer to sell and import”) the Original Code, Modifications, or portions thereof, but solely to the extent that any such patent is reasonably necessary to enable You to utilize, alone or in combination with other software, the Original Code,
Modifications, or any combination or portions thereof.
(c)
(d)
2.2. Contributor Grant.
Subject to third party intellectual property claims, each Contributor hereby grants You a world-wide, royalty-free, non-exclusive license
(a) under intellectual property rights (other than patent or trademark) Licensable by
Contributor, to use, reproduce, modify, display, perform, sublicense and distribute the
Modifications created by such Contributor (or portions thereof) either on an unmodified basis, with other Modifications, as Covered Code and/or as part of a Larger Work; and
(b) under patents now or hereafter owned or controlled by Contributor, to make, have made, use and sell (“offer to sell and import”) the Contributor Version (or portions thereof), but solely to the extent that any such patent is reasonably necessary to enable
You to utilize, alone or in combination with other software, the Contributor Version (or portions thereof).
(c)
(d)
3 DISTRIBUTION OBLIGATIONS.
3.1. Application of License.
The Modifications which You create or to which You contribute are governed by the terms of this License, including without limitation Section 2.2. The Source Code version of Covered Code may be distributed only under the terms of this License or a future version of this License released under Section 6.1, and You must include a copy of this License with every copy of the Source Code You distribute. You may not offer or impose any terms on any Source Code version that alters or restricts the applicable version of this License or the recipients’ rights hereunder. However, You may include an additional document offering the additional rights described in Section 3.5.
3.2. Availability of Source Code.
viii
Any Modification created by You will be provided to the Initial Developer in Source
Code form and are subject to the terms of the License.
3.3. Description of Modifications.
You must cause all Covered Code to which You contribute to contain a file documenting the changes You made to create that Covered Code and the date of any change. You must include a prominent statement that the Modification is derived, directly or indirectly, from Original Code provided by the Initial Developer and including the name of the Initial Developer in (a) the Source Code, and (b) in any notice in an Executable version or related documentation in which You describe the origin or ownership of the Covered Code.
3.4. Intellectual Property Matters.
(a) Third Party Claims.
If Contributor has knowledge that a license under a third party’s intellectual property rights is required to exercise the rights granted by such Contributor under Sections 2.1 or 2.2, Contributor must include a text file with the Source Code distribution titled
“LEGAL” which describes the claim and the party making the claim in sufficient detail that a recipient will know whom to contact. If Contributor obtains such knowledge after the Modification is made available as described in Section 3.2, Contributor shall promptly modify the LEGAL file in all copies Contributor makes available thereafter and shall take other steps (such as notifying appropriate mailing lists or newsgroups) reasonably calculated to inform those who received the Covered Code that new knowledge has been obtained.
(b) Contributor APIs.
If Contributor’s Modifications include an application programming interface and
Contributor has knowledge of patent licenses which are reasonably necessary to implement that API, Contributor must also include this information in the LEGAL file.
(c) Representations.
Contributor represents that, except as disclosed pursuant to Section 3.4(a) above,
Contributor believes that Contributor’s Modifications are Contributor’s original creation(s) and/or Contributor has sufficient rights to grant the rights conveyed by this
License.
3.5. Required Notices.
You must duplicate the notice in Exhibit A in each file of the Source Code. If it is not possible to put such notice in a particular Source Code file due to its structure, then You must include such notice in a location (such as a relevant directory) where a user would be likely to look for such a notice. If You created one or more Modification(s) You may add your name as a Contributor to the notice described in Exhibit A. You must also duplicate this License in any documentation for the Source Code where You describe recipients’ rights or ownership rights relating to Covered Code. You may choose to offer, and to charge a fee for, warranty, support, indemnity or liability obligations to one or more recipients of Covered Code. However, You may do so only on Your own behalf, and not on behalf of the Initial Developer or any Contributor.
3.6. Distribution of Executable Versions.
You may distribute Covered Code in Executable form only if the requirements of
Section 3.1-3.5 have been met for that Covered Code. You may distribute the
Executable version of Covered Code or ownership rights under a license of Your choice, which may contain terms different from this License, provided that You are in compliance with the terms of this License and that the license for the Executable version does not attempt to limit or alter the recipient’s rights in the Source Code version from the rights set forth in this License. If You distribute the Executable version under a different license You must make it absolutely clear that any terms which differ from this License are offered by You alone, not by the Initial Developer or any
Contributor. If you distribute executable versions containing Covered Code as part of a product, you must reproduce the notice in Exhibit B in the documentation and/or other materials provided with the product.
3.7. Larger Works.
You may create a Larger Work by combining Covered Code with other code not governed by the terms of this License and distribute the Larger Work as a single product. In such a case, You must make sure the requirements of this License are fulfilled for the Covered Code.
3.8. Restrictions.
You may not remove any product identification, copyright, proprietary notices or labels from gSOAP.
4 INABILITY TO COMPLY DUE TO STATUTE OR REGULATION.
If it is impossible for You to comply with any of the terms of this License with respect to some or all of the Covered Code due to statute, judicial order, or regulation then You must: (a) comply with the terms of this License to the maximum extent possible; and
(b) describe the limitations and the code they affect. Such description must be included in the LEGAL file described in Section 3.4 and must be included with all distributions of the Source Code. Except to the extent prohibited by statute or regulation, such description must be sufficiently detailed for a recipient of ordinary skill to be able to understand it.
5 APPLICATION OF THIS LICENSE.
This License applies to code to which the Initial Developer has attached the notice in
Exhibit A and to related Covered Code.
6 VERSIONS OF THE LICENSE.
6.1. New Versions.
Grantor may publish revised and/or new versions of the License from time to time.
Each version will be given a distinguishing version number.
6.2. Effect of New Versions.
Once Covered Code has been published under a particular version of the License, You may always continue to use it under the terms of that version. You may also choose to use such Covered Code under the terms of any subsequent version of the License.
6.3. Derivative Works.
If You create or use a modified version of this License (which you may only do in order to apply it to code which is not already Covered Code governed by this License), You must (a) rename Your license so that the phrase “gSOAP” or any confusingly similar phrase do not appear in your license (except to note that your license differs from this
License) and (b) otherwise make it clear that Your version of the license contains terms which differ from the gSOAP Public License. (Filling in the name of the Initial
Developer, Original Code or Contributor in the notice described in Exhibit A shall not of themselves be deemed to be modifications of this License.)
7 DISCLAIMER OF WARRANTY.
COVERED CODE IS PROVIDED UNDER THIS LICENSE ON AN “AS IS” BASIS,
WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED OR
STATUTORY, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF MERCHANTABILITY, OF FITNESS FOR A PARTICULAR
PURPOSE, NONINFRINGEMENT OF THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS, AND ANY WARRANTY THAT MAY ARISE BY REASON
OF TRADE USAGE, CUSTOM, OR COURSE OF DEALING. WITHOUT
LIMITING THE FOREGOING, YOU ACKNOWLEDGE THAT THE SOFTWARE
IS PROVIDED “AS IS” AND THAT THE AUTHORS DO NOT WARRANT THE
SOFTWARE WILL RUN UNINTERRUPTED OR ERROR FREE. LIMITED
LIABILITY THE ENTIRE RISK AS TO RESULTS AND PERFORMANCE OF THE
SOFTWARE IS ASSUMED BY YOU. UNDER NO CIRCUMSTANCES WILL THE
AUTHORS BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL,
EXEMPLARY OR CONSEQUENTIAL DAMAGES OF ANY KIND OR NATURE
WHATSOEVER, WHETHER BASED ON CONTRACT, WARRANTY, TORT
(INCLUDING NEGLIGENCE), STRICT LIABILITY OR OTHERWISE, ARISING
OUT OF OR IN ANY WAY RELATED TO THE SOFTWARE, EVEN IF THE
AUTHORS HAVE BEEN ADVISED ON THE POSSIBILITY OF SUCH DAMAGE
OR IF SUCH DAMAGE COULD HAVE BEEN REASONABLY FORESEEN, AND
NOTWITHSTANDING ANY FAILURE OF ESSENTIAL PURPOSE OF ANY
EXCLUSIVE REMEDY PROVIDED. SUCH LIMITATION ON DAMAGES
INCLUDES, BUT IS NOT LIMITED TO, DAMAGES FOR LOSS OF GOODWILL,
LOST PROFITS, LOSS OF DATA OR SOFTWARE, WORK STOPPAGE,
COMPUTER FAILURE OR MALFUNCTION OR IMPAIRMENT OF OTHER
GOODS. IN NO EVENT WILL THE AUTHORS BE LIABLE FOR THE COSTS OF
PROCUREMENT OF SUBSTITUTE SOFTWARE OR SERVICES. YOU
ACKNOWLEDGE THAT THIS SOFTWARE IS NOT DESIGNED FOR USE IN ON-
LINE EQUIPMENT IN HAZARDOUS ENVIRONMENTS SUCH AS OPERATION
OF NUCLEAR FACILITIES, AIRCRAFT NAVIGATION OR CONTROL, OR LIFE-
CRITICAL APPLICATIONS. THE AUTHORS EXPRESSLY DISCLAIM ANY
LIABILITY RESULTING FROM USE OF THE SOFTWARE IN ANY SUCH ON-
LINE EQUIPMENT IN HAZARDOUS ENVIRONMENTS AND ACCEPTS NO
LIABILITY IN RESPECT OF ANY ACTIONS OR CLAIMS BASED ON THE USE
OF THE SOFTWARE IN ANY SUCH ON-LINE EQUIPMENT IN HAZARDOUS
ENVIRONMENTS BY YOU. FOR PURPOSES OF THIS PARAGRAPH, THE
TERM “LIFE- CRITICAL APPLICATION” MEANS AN APPLICATION IN
WHICH THE FUNCTIONING OR MALFUNCTIONING OF THE SOFTWARE
MAY RESULT DIRECTLY OR INDIRECTLY IN PHYSICAL INJURY OR LOSS
OF HUMAN LIFE. THIS DISCLAIMER OF WARRANTY CONSTITUTES AN
ESSENTIAL PART OF THIS LICENSE. NO USE OF ANY COVERED CODE IS
AUTHORIZED HEREUNDER EXCEPT UNDER THIS DISCLAIMER.
8 TERMINATION.
8.1.
This License and the rights granted hereunder will terminate automatically if You fail to comply with terms herein and fail to cure such breach within 30 days of becoming aware of the breach. All sublicenses to the Covered Code which are properly granted shall survive any termination of this License. Provisions which, by their nature, must remain in effect beyond the termination of this License shall survive.
8.2.
8.3.
If You assert a patent infringement claim against Participant alleging that such
Participant’s Contributor Version directly or indirectly infringes any patent where such claim is resolved (such as by license or settlement) prior to the initiation of patent infringement litigation, then the reasonable value of the licenses granted by such
Participant under Sections 2.1 or 2.2 shall be taken into account in determining the amount or value of any payment or license.
8.4.
In the event of termination under Sections 8.1 or 8.2 above, all end user license agreements (excluding distributors and resellers) which have been validly granted by
You or any distributor hereunder prior to termination shall survive termination.
9 LIMITATION OF LIABILITY.
UNDER NO CIRCUMSTANCES AND UNDER NO LEGAL THEORY, WHETHER
TORT (INCLUDING NEGLIGENCE), CONTRACT, OR OTHERWISE, SHALL
YOU, THE INITIAL DEVELOPER, ANY OTHER CONTRIBUTOR, OR ANY
DISTRIBUTOR OF COVERED CODE, OR ANY SUPPLIER OF ANY OF SUCH
PARTIES, BE LIABLE TO ANY PERSON FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY CHARACTER
INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF GOODWILL,
WORK STOPPAGE, COMPUTER FAILURE OR MALFUNCTION, OR ANY AND
ALL OTHER COMMERCIAL DAMAGES OR LOSSES, EVEN IF SUCH PARTY
SHALL HAVE BEEN INFORMED OF THE POSSIBILITY OF SUCH DAMAGES.
THIS LIMITATION OF LIABILITY SHALL NOT APPLY TO LIABILITY FOR
DEATH OR PERSONAL INJURY RESULTING FROM SUCH PARTY’S
NEGLIGENCE TO THE EXTENT APPLICABLE LAW PROHIBITS SUCH
LIMITATION. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THIS
EXCLUSION AND LIMITATION MAY NOT APPLY TO YOU.
10 U.S. GOVERNMENT END USERS.
11 MISCELLANEOUS.
12 RESPONSIBILITY FOR CLAIMS.
As between Initial Developer and the Contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under this
License and You agree to work with Initial Developer and Contributors to distribute such responsibility on an equitable basis. Nothing herein is intended or shall be deemed to constitute any admission of liability.
EXHIBIT A.
“The contents of this file are subject to the gSOAP Public License Version 1.3 (the
“License”); you may not use this file except in compliance with the License. You may obtain a copy of the License athttp://www.cs.fsu.edu/ engelen/soaplicense.html
ix
Software distributed under the License is distributed on an “AS IS” basis, WITHOUT
WARRANTY OF ANY KIND, either express or implied. See the License for the specific language governing rights and limitations under the License.
The Original Code of the gSOAP Software is: stdsoap.h, stdsoap2.h, stdsoap.c, stdsoap2.c, stdsoap.cpp, stdsoap2.cpp, soapcpp2.h, soapcpp2.c, soapcpp2_lex.l, soapcpp2_yacc.y, error2.h, error2.c, symbol2.c, init2.c, soapdoc2.html, and soapdoc2.pdf, httpget.h, httpget.c, stl.h, stldeque.h, stllist.h, stlvector.h, stlset.h.
The Initial Developer of the Original Code is Robert A. van Engelen. Portions created by Robert A. van Engelen are
Copyright (C) 2001-2004 Robert A. van Engelen, Genivia inc. All Rights Reserved.
Contributor(s):
“________________________.”
[Note: The text of this Exhibit A may differ slightly form the text of the notices in the
Source Code files of the Original code. You should use the text of this Exhibit A rather than the text found in the Original Code Source Codefor Your Modifications.]
EXHIBIT B.
“Part of the software embedded in this product is gSOAP software.
Portions created by gSOAP are Copyright (C) 2001-2009 Robert A. van Engelen,
Genivia inc. All Rights Reserved. THE SOFTWARE IN THIS PRODUCT WAS IN
PART PROVIDED BY GENIVIA INC AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.” http://www.cs.fsu.edu/~engelen/license.html
■ About fonts
Fonts are (c) Bitstream (see below). DejaVu changes are in public domain.
Glyphs imported from Arev fonts are (c) Tavmjong Bah (see below)
Bitstream Vera Fonts Copyright
------------------------------
Copyright (c) 2003 by Bitstream, Inc. All Rights Reserved. Bitstream Vera is a trademark of Bitstream, Inc.
Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts accompanying this license (“Fonts”) and associated documentation files (the “Font
Software”), to reproduce and distribute the Font Software, including without limitation the rights to use, copy, merge, publish, distribute, and/or sell copies of the Font
Software, and to permit persons to whom the Font Software is furnished to do so, subject to the following conditions:
The above copyright and trademark notices and this permission notice shall be included in all copies of one or more of the Font Software typefaces.
The Font Software may be modified, altered, or added to, and in particular the designs of glyphs or characters in the Fonts may be modified and additional glyphs or characters may be added to the Fonts, only if the fonts are renamed to names not containing either the words “Bitstream” or the word “Vera”.
This License becomes null and void to the extent applicable to Fonts or Font Software that has been modified and is distributed under the “Bitstream Vera” names.
The Font Software may be sold as part of a larger software package but no copy of one or more of the Font Software typefaces may be sold by itself.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF
ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT,
TRADEMARK, OR OTHER RIGHT. IN NO EVENT SHALL BITSTREAM OR THE
GNOME FOUNDATION BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
LIABILITY, INCLUDING ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES, WHETHER IN AN ACTION OF CONTRACT,
TORT OR OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO
USE THE FONT SOFTWARE OR FROM OTHER DEALINGS IN THE FONT
SOFTWARE.
Except as contained in this notice, the names of Gnome, the Gnome Foundation, and
Bitstream Inc., shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Font Software without prior written authorization from the Gnome
Foundation or Bitstream Inc., respectively. For further information, contact: fonts at gnome dot org.
Arev Fonts Copyright
------------------------------
Copyright (c) 2006 by Tavmjong Bah. All Rights Reserved.
Permission is hereby granted, free of charge, to any person obtaining a copy of the fonts accompanying this license (“Fonts”) and associated documentation files (the “Font
Software”), to reproduce and distribute the modifications to the Bitstream Vera Font
Software, including without limitation the rights to use, copy, merge, publish, distribute, and/or sell copies of the Font Software, and to permit persons to whom the
Font Software is furnished to do so, subject to the following conditions:
The above copyright and trademark notices and this permission notice shall be included in all copies of one or more of the Font Software typefaces.
The Font Software may be modified, altered, or added to, and in particular the designs of glyphs or characters in the Fonts may be modified and additional glyphs or characters may be added to the Fonts, only if the fonts are renamed to names not containing either the words “Tavmjong Bah” or the word “Arev”.
This License becomes null and void to the extent applicable to Fonts or Font Software that has been modified and is distributed under the “Tavmjong Bah Arev” names.
The Font Software may be sold as part of a larger software package but no copy of one or more of the Font Software typefaces may be sold by itself.
THE FONT SOFTWARE IS PROVIDED “AS IS”, WITHOUT WARRANTY OF
ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE AND NONINFRINGEMENT OF COPYRIGHT, PATENT,
TRADEMARK, OR OTHER RIGHT. IN NO EVENT SHALL TAVMJONG BAH BE
LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, INCLUDING
ANY GENERAL, SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, WHETHER IN AN ACTION OF CONTRACT, TORT OR
OTHERWISE, ARISING FROM, OUT OF THE USE OR INABILITY TO USE THE
FONT SOFTWARE OR FROM OTHER DEALINGS IN THE FONT SOFTWARE.
Except as contained in this notice, the name of Tavmjong Bah shall not be used in advertising or otherwise to promote the sale, use or other dealings in this Font Software without prior written authorization from Tavmjong Bah. For further information, contact: tavmjong @ free. fr.
x
© 2010 Yamaha Corporation Printed in Malaysia WV60880
advertisement