KWA AKG 74M Airsoft gun Operator's Manual

MM24_AKG74M_V01 R2012.10.02
MAGAZINE DIAGRAM AND PARTS LIST
219
201
®
228
228
210
206
218
200
202
203
204
216
229
OPERATOR’S MANUAL
223
231
225
207
209
213
226
227
221
226
232
226
227
215
208
214
226
220
232
222
226
232
226
232
222
224
220
205
217
230
211
Parts #
Description
Parts #
Description
AKG74M-200
MAGAZINE SLEEVE BODY
AKG74M-217
MAGAZINE BASE SEAL
AKG74M-201
MAGAZINE STOP DIAL
AKG74M-218
MAGAZINE NOZZLE SEAL
AKG74M-202
MAGAZINE STOP LEVER
AKG74M-219
MAGAZINE STOP DIAL SPACER
AKG74M-203
MAGAZINE STOP INDICATOR
AKG74M-220
MAGAZINE INNER POST
AKG74M-204
MAGAZINE STOP SELECTOR
AKG74M-221
MAGAZINE GAS EXPANSION TUBE
AKG74M-205
MAGAZINE BASE PLATE STOP
AKG74M-222
MAGAZINE BASE PINS
AKG74M-206
MAGAZINE FOLLOWER
AKG74M-223
MAGAZINE STOP SPRING
AKG74M-207
MAGAZINE STOP KEY
AKG74M-224
MAGAZINE BASE PLATE STOP SPRING
AKG74M-208
MAGAZINE BASE PLATE
AKG74M-225
MAGAZINE FOLLOWER SPRING
AKG74M-209
MAGAZINE BODY
AKG74M-226
MAGAZINE INNER POST SCREWS
AKG74M-210
MAGAZINE FEED LIP
AKG74M-227
MAGAZINE BASE SCREWS
AKG74M-211
MAGAZINE BASE
AKG74M-228
MAGAZINE FEED LIP SCREW
AKG74M-213
MAGAZINE RELEASE VALVE BLOCK
AKG74M-229
MAGAZINE STOP DIAL DÉTENTE
AKG74M-214
MAGAZINE FOLLOWER STOP
AKG74M-230
MAGAZINE CHARGING VALVE
AKG74M-215
MAGAZINE FOLLOWER STOP PIN
AKG74M-231
MAGAZINE RELEASE VALVE
AKG74M-216
MAGAZINE FEED LIP PIN
AKG74M-232
MAGAZINE INNER POST SEAL
KWA Performance Industries, Inc.
19
Copyright © October, 2012 KWA Performance Industries, Inc. All Rights Reserved.
AKG 74M
AKG 74M
TABLE OF CONTENTS
PARTS LIST
Parts #
Description
Parts #
Description
Parts #
AKG74M-1
PISTOL GRIP
AKG74M-54
HAND GUARD SPRING
AKG74M-106 FRONT TRUNNION PIN SCREW
AKG74M-2
UPPER HAND GUARD
AKG74M-55
REAR SIGHT LEAF SPRING
AKG74M-107 REAR SIGHT LEAF SCREW
AKG74M-3
BOLT
AKG74M-56
RECOIL SPRING GUIDE (2X)
AKG74M-108 REAR SIGHT BASE SCREW
AKG74M-4
INNER PISTON
AKG74M-57
SELECTOR LEVER
AKG74M-110 GAS BLOCK SCREW
Specifications ..................................................................................................4
AKG74M-5
FRONT LATCH BASE
AKG74M-58
IMPACT HAMMER STOP
AKG74M-111 INNER BARREL BASE SCREWS
AKG74M-6
FRONT LATCH DÉTENTE
AKG74M-59
IMPACT HAMMER STOP SPRING
AKG74M-112 CHAMBER SCREW
Package Contents............................................................................................4
AKG74M-7
FRONT LATCH
AKG74M-60
OUTER BARREL
AKG74M-114 REAR TRUNNION BASE SCREW
AKG74M-8
INNER BARREL BASE
AKG74M-61
GAS TUBE
AKG74M-115 SIDE RAIL SCREWS
AKG74M-9
INNER BARREL CLAMP
AKG74M-62
GAS PISTON
AKG74M-117 GAS PLUG PIN
AKG74M-10
HOP-UP CYLINDER
AKG74M-63
INNER BARREL
AKG74M-118 IMPACT HAMMER RESET PIN
AKG74M-11
HOP-UP ADJUSTMENT DIAL
AKG74M-64
CLEANING ROD
AKG74M-119 INNER PISTON PIN
AKG74M-12
JET NOZZLE
AKG74M-65
SELECTOR LEVER PIN
AKG74M-120 CYLINDER PLUG PIN
AKG74M-13
LOWER HAND GUARD
AKG74M-66
FIRE CONTROL GROUP PINS
AKG74M-121 BOLT CARRIER PIN
AKG74M-15
HOP-UP NUB
AKG74M-67
IMPACT HAMMER SLEEVE
AKG74M-122 MAGAZINE CATCH PIN
AKG74M-16
RECOIL BUFFER
AKG74M-68
TRIGGER SLEEVE
AKG74M-123 RECOIL BUFFER PIN
AKG74M-17
BOLT BASE
AKG74M-69
IMPACT HAMMER RESET PIN
AKG74M-124 CYLINDER PLUG SEAL
Blank Fire Feature............................................................................................8
AKG74M-18
RECIEVER
AKG74M-70
FRONT LATCH SCREW
AKG74M-125 CYLINDER PLUG SPACER
AKG74M-19
REAR SIGHT BASE
AKG74M-71
TRUNNION SCREWS
AKG74M-126 INNER PISTON SEAL
Fire Selector Switch.........................................................................................9
AKG74M-20
REAR TRUNNION
AKG74M-72
GRIP SCREW
AKG74M-127 LONG BOLT CARRIER SCREW
AKG74M-21
BOLT CARRIER
AKG74M-73
STOCK HINGE PIN
AKG74M-128 IMPACT HAMMER E-CLIP
AKG74M-22
PISTON STOP
AKG74M-74
REAR SIGHT BLOCK PIN
AKG74M-500 POLYMER STOCK
AKG74M-23
UPPER HAND GUARD RETAINER
AKG74M-75
HOP-UP NUB SPACER
AKG74M-501 STOCK RELEASE BUTTON
AKG74M-24
HAND GUARD STOP
AKG74M-76
FRONT TRUNNION PIN
AKG74M-502 STOCK TRAPDOOR
AKG74M-25
IMPACT BLOCK BASE
IMPACT HAMMER
AKG74M-77
AKG74M-503 STOCK BUTTPLATE
AKG74M-26
IMPACT BLOCK RESET SPRING
PIN
AKG74M-27
IMPACT HAMMER LOCK
AKG74M-78
SHORT BOLT CARRIER SCREW
AKG74M-505 STOCK SLING SWIVEL BASE
AKG74M-28
INTERRUPTER
AKG74M-79
RECOIL SPRING GUIDE SET PIN
AKG74M-506 STOCK SLING SWIVEL
AKG74M-29
TRIGGER
AKG74M-81
PISTON RETURN SPRING PIN
AKG74M-507 STOCK SLING SWIVEL CAP
Hop-Up System .............................................................................................12
AKG74M-30
SEAR
AKG74M-82
JET NOZZLE PIN
AKG74M-508 STOCK SLING LOOP
AKG74M-31
HAMMER
AKG74M-85
HOP-UP BUCKING
AKG74M-509 STOCK TRAPDOOR SPRING
Cleaning................................................................................................... 13-14
AKG74M-32
SELECTOR BASE
AKG74M-86
PISTON SEAL
AKG74M-510 STOCK SLING SWIVEL SCREW
AKG74M-33
STOCK LOCKING LATCH
AKG74M-87
RECOIL SPRING
AKG74M-511 STOCK HINGE SCREW
AKG74M-34
STOCK LATCH RELEASE BUTTON
AKG74M-88
HAMMER SPRING
AKG74M-512 STOCK BUTTPLATE SCREW
AKG74M-35
RECOIL SPRING GUIDE BASE
AKG74M-89
SEAR SPRING
AKG74M-520 FRONT SIGHT POST SPACER
AKG74M-36
RECOIL SPRING GUIDE STOP
AKG74M-90
INTERRUPTER SPRING
AKG74M-521 MUZZLE BRAKE
AKG74M-37
LOWER HAND GUARD RETAINER
AKG74M-91
IMPACT HAMMER LOCK SPRING
AKG74M-522 MUZZLE BRAKE SPACER
AKG74M-38
HAND GUARD RETAINER LEVER
AKG74M-92
IMPACT HAMMER RESET SPRING
AKG74M-523 FRONT SIGHT
AKG74M-39
HAND GUARD RELEASE LEVER
AKG74M-93
HAMMER GROUP LOCK SPRING
AKG74M-524 FRONT SIGHT POST
AKG74M-40
CYLINDER PLUG
AKG74M-94
FRONT LATCH SPRING
AKG74M-525 MUZZLE BRAKE DETENTE
AKG74M-45
GAS BLOCK
AKG74M-95
STOCK LATCH SPRING
AKG74M-46
REAR SIGHT LEAF
AKG74M-96
JET NOZZLE SPRING
AKG74M-47
REAR SIGHT ADJUSTMENT
BUTTON
AKG74M-97
PISTON RETURN SPRING
AKG74M-527 THREADED BARREL NUT
AKG74M-99
REAR SIGHT SLIDER SPRING
AKG74M-528 BARREL NUT SCREW
AKG74M-48
REAR SIGHT SLIDER
AKG74M-100 MAGAZINE CATCH SPRING
AKG74M-49
MAGAZINE CATCH
AKG74M-101 RECOIL BUFFER PAD
AKG74M-50
OPTICS SIDE RAIL
AKG74M-102 PISTON STOP SCREW
AKG74M-52
DUST COVER
AKG74M-103 TRIGGER SPRING
AKG74M-53
TRIGGER GUARD
AKG74M-105 SELECTOR LEVER PIN
Use of this manual............................................................................................2
Safety Guidelines......................................................................................... 2-3
Charging Gas...................................................................................................5
Discharging Gas...............................................................................................6
Loading BBs................................................................................................. 6-7
Folding Stock..................................................................................................10
Front Sight Adjustment ..................................................................................10
Disassembly...................................................................................................11
Troubleshooting .............................................................................................15
Operating Under Unusual Conditions.............................................................15
Diagram and Parts Lists .......................................................................... 16-19
1
Description
AKG74M-504 STOCK HINGE
AKG74M-526
AKG74M-529
MUZZLE BRAKE DETENTE
SPRING
MUZZLE BRAKE DETENTE
SCREW
AKG74M-530 FRONT SIGHT SCREW
18
AKG 74M
Parts Diagram
USE OF THIS MANUAL
52
36
26
94
6118
18
5
128
94
5
7
91
27
58 25
3088
69
103
30
68
92
29
25
77
106
57
29
115
66
115
7
95
71
95
115
53
100
10071
Eye Protection
Eye protection should be worn at all times when both shooting and maintaining your Airsoft
gun. Protect your eyes from BBs under spring pressure while performing maintenance on
your Airsoft gun.
16
35
105
73
Assume Every Gun is Always Loaded
Until you are certain the chamber is empty, treat every gun as if it were loaded. Do not
assume the chamber is empty based on your memory or someone else’s words. Always
remove the magazine and visually check to confirm the chamber is empty.
33
Beware of Barrel Obstructions
73
71
71114
Ensure the Airsoft gun barrel is free of obstructions before you fire the gun. Even the
smallest obstruction such as dirt, dust or a stuck cleaning patch can cause a jam, misfire
or malfunction.
20
71
34
49
122
123
71
71
34 66
101
33 65
71
66
115
5049
105
32
66
79
35
71
66
50
101
The effective shooting range is approximately 175 feet. BBs fired from this Airsoft gun may
travel further than intended. Make certain that you have an adequate backstop.
56
16
57
32
66
70115
101
65
93
7 115
123
103
89
93
68
70
76
101
114
20
Muzzle Control
53
71
Always keep the muzzle of the gun pointed in a safe direction. Never point the muzzle at a
person or object that you do not intend to shoot.
122
71
71
512
509
Keep Your Safety On
512
509
508
503
502
508
511
511
17
502
501
506
504
507
507
504
512
501
510
511
511
511
512 503
500
506
505
511
Keep the gun’s safety on until your sights are aligned on your target and you are ready to
fire.
Keep Your Finger Off The Trigger
500
505
WARNING! Failure to follow safety guidelines may result
in serious injury.
Safety Distance
79
87
31 89
77
67 106
18
56
31
90
92
59
87
88
69
91
6
76
!
56
90
27
58
59
28
128
2667
118
SAFETY GUIDELINES
56
36
28
Before operating the Airsoft gun, read this manual in its entirety. Important safety topics
and tips are discussed throughout all of the chapters. It’s important that the operator know
the principles of gun handling safety and operation prior to firing the Airsoft gun.
52
510
Keep your finger off the trigger and out of the trigger guard until your sights are aligned on
your target and you are ready to fire.
!
WARNING! Airsoft BBs can be a choking hazard. Keep
them away from children.
2
AKG 74M
SAFETY GUIDELINES
Parts Diagram
Identify Your Target and Backstop
Before you pull the trigger, make certain of your target and what is beyond it. The Airsoft
gun should never be fired at surfaces such as rocks, glass, water, or other hard surfaces
where BBs are likely to ricochet in unpredictable directions.
!
62
121
WARNING! Adult supervision is required for any person
under the age of 18.
21
3
Failure To Fire
96 -1
82
If the Airsoft gun fails to fire, misfires, or malfunctions, do not look into the gun barrel. BBs
can become lodged into the chamber, and serious eye injury may occur.
119
81
Maintain Your Gun Properly
97
17
124
120
520
528
521
527
24
61
523
522
525
528
526
54
529
45
530
63
46
38
60
37
64
55
110
19
107
107
99
47
48
39
108
74
13
9
112
111
15
111
8
Alcohol, Medications and Drugs
Your Responsibility
102
524
The orange tip on Airsoft guns helps Law Enforcement distinguish between the replica
guns from their real firearm counterparts. Altering the coloration or markings required by
state or Federal law so as to make the product look more like a firearm is dangerous and
may be a crime. Operator assumes all risks and responsibility when doing so.
Do not handle or operate your Airsoft gun while under the influence of alcohol, medication
or drugs.
127
22
125
2
23
Orange Tip
Airsoft guns have been mistaken by Police and Law Enforcement as real firearms. A
confrontation with law enforcement while carrying an Airsoft gun can result in serious injury
or even death. It is strongly advised to operate the Airsoft gun at a safe and legal location.
In the event that you are approached by Law Enforcement personnel, you must comply with
their instructions immediately to avoid an incident.
4
78
117
Store Your Gun Safely
Hazards of Being Mistaken for a Real Firearm
86
40
Performing proper maintenance, as outlined in this manual, ensures that your Airsoft
gun will be safe to shoot and will perform to its designed specifications for many years.
Alterations, modifications or adjustments may damage your Airsoft gun, make it unsafe to
shoot, and will void all warranty claims.
Always store the Airsoft gun in a safe place, and out of the reach of children. Always
transport the Airsoft gun in a carrying case. Never display the Airsoft gun in a public place.
Keep the safety engaged, and remove the magazine before storing the Airsoft gun.
Note: it is your responsibility to take every reasonable precaution to
ensure the safe storage and transportation of your Airsoft gun.
126
12 -1
75
112
85
10
11
1
72
Your Airsoft gun is well-engineered and manufactured to the highest standards. It was
carefully inspected before it was packaged and shipped from our factory. Its safe use
depends on you alone. You are the ultimate safety device. Like many other devices, your
Airsoft gun is safe unless handled in an irresponsible or uneducated manner.
3
16
AKG 74M
BASIC TROUBLESHOOTING GUIDE
SYMPTOMS
POSSIBLE CAUSE
SOLUTIONS
Slide jams / Will not complete cycle
Dry internals
Add silicone to cylinder / main seal/ rails
Double feeds BBs into
chamber / BB’s roll out of barrel
Hop-up adjustment too tight
Release hop-up or replace bucking
BBs will not release from magazine /
bent mag lip/ check bb condition
Bent magazine lip
Replace magazine lip
Leaking release valve & charging valve
Dry O-ring
Add silicone oil to valves / Replace valves
Slide stop engages while shooting BBs
Weak slide stop spring
Adjust tension
Magazine base plate will not lock
Broken base plate lock
Replace base plate lock
Magazine base leaking air
Worn out base seal
Replace magazine base seal
Cylinder will not load BBs into chamber
Broken cylinder tab
Replace cylinder
Trigger will not reset
Worn out trigger spring /
trigger bar spring
Replace trigger spring / trigger bar spring
Operating Under Unusual Conditions
Unusual conditions are defined as any condition requiring special maintenance.
Perform maintenance outlined for the climate similar to your operational area
Extreme Cold:
Operating an Airsoft gas gun in extremely cold temperatures is not recommended. Cold
temperatures will cause the Hop-up Bucking to harden, reducing its effectiveness. Gas
will not expand properly in cold temperatures, so both the cycling rate and power will be
dramatically reduced.
Extreme Heat:
Operating an Airsoft gas gun in extremely hot temperatures is also not recommended.
Leaving the gun in direct sunlight for long periods of time, or operating in extremely hot
areas will cause the gas to over-expand, damaging the internal workings of the gun. The
increase in internal pressure from the expanding gas can also damage the seals and cause
leaks in the magazine.
SPECIFICATIONS
• Overall Length (Retracted) = 70.5 cm [27.76”]
• Overall Length (Extended) = 94.5 cm [37.20”]
• Inner Barrel Length = 420 mm
• Inner Barrel Diameter = 6.05 mm
• Weight = 3.52 kg [7.76 lbs]
• Barrel Thread = -14 mm
• Caliber = 6 mm
• Magazine Capacity = 40 rounds
• Rate of Fire = 14+ RPS
• Velocity = 118-125 MPS [390-410 FPS]
• Energy Output with 0.20g BB = 1.49 Joules
• Gas System = Force Velocity
• Propellant = Green Gas
*Individual test results may vary depending on brand of BBs, and chronograph used.
Special Features:
• Gas operated recoil blow back
• Realistic construction & field stripping
• Fully metal alloy receiver
• AK side rail
• Folding stock
• Blank fire mode
• Semi and full auto select fire
• Adjustable hop-up
PACKAGE CONTENTS
1 AKG 74M Airsoft Gun
1 Safety Cap
1 Sight Adjustment Tool
1 Cleaning Rod
1 Owners Manual
1 Oil Bottle
Dust or Sand:
Dust or sand can get into a gas gun and cause malfunctions and/or excessive wear. Keep
the gun covered whenever possible. Use lubricant sparingly, as lube naturally attracts dirt
and other particles. After use in a dusty area, always field strip the gun (refer to Disassembly
Section) and clean any areas you can reach with a soft, lint-free cloth.
15
4
AKG 74M
6. Use a clean cotton cloth to wipe down the surface of the charging handle and bolt carrier.
CHARGING GAS
1.Release the magazine by pressing the magazine catch lever towards the magazine.
2. Push the gas canister nozzle into the charging valve. Make sure the canister is in
a vertical position when charging.
7. Use a clean cotton cloth to clean inside the upper receiver and magazine well.
8. Clean the remainder of the Airsoft gun with cotton-tipped swab, or general purpose
cleaning cloths.
3. Charge the magazine for approximately 30-40 seconds.
Cotton Cloth
!
WARNING: Avoid dropping the magazine. Sudden impact with a
hard surface may cause damage to the magazine.
Bolt carrier
Note: It is normal to have minor leaking from the charging valve during charging due to
high pressure built up inside the magazine. It is recommended to keep the gas release valve
slightly oiled. Room temperature is the ideal temperature for shooting. You may experience
a delayed action if the surrounding temperature drops below 68º F.
Cotton Cloth
Upper receiver
Note: Do not expose the magazine to direct sunlight or incinerate the magazine, as this
Cotton Cloth
may cause the magazine to burst. It is strongly recommended to empty the gas from the
magazine after shooting. Be certain that the gas does not make contact with eyes or skin
while being released, as any contact will cause cold burns.
Magazine well
9. Oil the cylinder and hammer.
1
Magazine
2
Magazine Catch Lever
Nozzle
Charging
Valve
Lubricating dry seals and o-rings are essential. Unload BBs from the magazine. Make sure
the magazine is free of gas before lubricating the magazine’s charging valve and release
valve.
Use only the recommended 100% silicone oil, available for purchase at the Airsoft dealer
where you purchased your KWA products. Any other type of lubricant may damage the
products.
!
5
DO NOT use spray silicone oil as a
cleaning solution for the inner barrel.
WARNING!
14
AKG 74M
Cleaning
!
DISCHARGING GAS
WARNING! Unload and clear the Airsoft gun before cleaning.
Hold the magazine at the bottom. Press the valve.
Residual gas may now be discharged.
Press on
valve
Green Gas safety tips:
Cleaning Procedure
The Airsoft gun barrel should be cleaned after each shooting session. Regular cleaning
prevents the effects of BB residue buildup that can hinder performance or jam the gun.
1. Ensure that the safety is engaged
2. Remove the magazine and clear the chamber of loaded BBs
• Check the canister for any cracks or leaks before using.
• Do not expose the canister to temperature over 104º F.
• Do not leave the canister directly over fire.
• Do not heat the canister.
• Keep the canister away from direct sunlight.
• Do not leave the canister in any type of vehicle.
BB LOADING BBs
3. Disable Hop-Up by dialing to the normal position (see Hop-Up section)
OPTION ONE - USING STANDARD BB LOADER
4. Disassemble the receiver (see Disassembly section)
1.Release the magazine from the Airsoft gun by pressing the magazine catch button.
5.Steps to use cleaning rod:
a. Cut a piece of clean cotton cloth to 1 inch by 0.5 inch size. Insert one end
of the cloth into the hole in the cleaning rod (adjust the length of cloth for
smooth entry into the barrel)
b. Wind the cloth around the cleaning rod
c. Insert the cleaning rod into the inner barrel, and push the rod through.
d.Remove the cleaning rod and check the cotton cloth for dirt. Repeat steps
a. through c. when necessary.
2. Fit the standard BB loader over the magazine feed lip.
3. Load the BBs into the BB loader.
4. Insert the plunger into the BB loader and push down to load BBs into the magazine.
WARNING: Always use high quality 6mm BBs, weighting 0.2g
or heavier. For best result use 0.25g KWA Perfect BBs. Never
use recycled or low grade BBs to prevent damage to your gun.
!
4
cleaning rod
3
cotton
cloth
!
13
DO NOT use spray silicone oil as a
cleaning solution for the inner barrel.
WARNING!
2
6
AKG 74M
OPTION TWO - USING KWA HIGH PERFORMANCE BB LOADER
HOP–UP SYSTEM
1.Release the magazine from the Airsoft gun by pressing the magazine catch
button.
The Hop-Up device is one of KWA’s standard features, giving Airsoft BBs greater stability,
further travel, and increased accuracy. Airsoft BBs are light-weight and can be affected by
wind when fired. With the Hop-Up system, the trajectory of the Airsoft BBs can be adjusted
according to the shooting environment or surroundings.
2. Slide open the trap door on top of the BB loader. Fill the BB loader with BBs.
*Do Not Overfill.
HOP-UP ADJUSTMENT
3. Slide open the accessory trap door and remove the GBBR attachment.
1. Test fire the gun to determine the amount of hopup needed.
4. Flip down the dust cover to reveal the loading nozzle.
2. Remove the Magazine.
5. Attach the GBBR attachment to the loading nozzle.
2
6. Fit BB loader over the magazine feed lip.
6. Test fire and adjust as needed.
!
4
5
loading
nozzle
4. Turn the Hop-Up Dial to adjust hop.
5. Left for more hop, right for less hop.
7. Press on BB loader plunger to load BB into magazine.
3
3. Pull the bolt back to access the Hop-Up Dial. WARNING: Do not release the bolt with hand in the chamber.
More
Hop
Less
Hop
GBBR
attachment
Bolt
6
Hop-Up Dial
7
HOP-UP ADJUSTMENT POINT
HOP UP
EFFECTIVENESS
!
WARNING: Always use high quality 6mm BBs, weighting 0.2g
or heavier. For best result use 0.25g KWA Perfect BBs. Never
use recycled or low grade BBs to prevent damage to your gun.
BB loading safety tips:
• Switch the selector to safe
• Be sure the safety cap is on
• Keep your finger off the trigger at all times
7
BB TRAJECTORY PATTERN
ADJUSTMENTS
NOT
EFFECTIVE
BB DROPS FREELY
TURN KNOB
TO LEFT
SLIGHTLY
BB TRAVELS AT SHORT TRAJECTORY
PATH
TURN KNOB
SLIGHTLY TO
LEFT
PROPERLY
BB TRAVELS DISTANCE AT A FLAT
TRAJECTORY PATH
NO
ADJUSTMENT
MADE
BB TRAVELS FLAT IN SHORT
DISTANCE, THEN GOES UP IN CURVE
AND DROPS FREELY
TURN KNOB
SLIGHTLY TO
RIGHT
BB TRAVELS AT UNSTABLE SPEED AND
IRREGULAR PATH
TURN KNOB
TO RIGHT
OVERLY
EXTREMELY
EFFECTIVE
12
AKG 74M
BLANK FIRE MODE
DISASSEMBLY
!
WARNING: Always place the safety cap on the barrel tip when
servicing your gun.
2
1.Remove magazine.
One of the standard features of the KWA AKG-74 Series is the Integrated Blank Fire
Device implemented in every AKG-74 magazine. This allows for the AKG-74 to be fired
continuously without ammunition for training use.
1. Push down and hold the Base Plate Stop to release the Magazine Base Plate.
2. Set the selector to semi-automatic.
0A
2. Slide the Base Plate backwards to reveal the Blank Fire Key.
3. Charge the bolt to reset the hammer.
Note: Check and clear the chamber of BB’s.
3. Insert the key into the Indicator Wheel.
4. Depress the spring guide to lift the cover.
4. Turn the Indicator Wheel to the desired position as shown.
5. Push the spring guide forward then left
to remove the spring guide.
!
6. Pull the bolt back then remove the bolt.
7. Flip up the take-down lever then remove the
hand guard.
Bolt
3
WARNING! Any loaded rounds can still fire with the Blank Fire
Device activated. Always make sure the gun is unloaded by
inspecting BOTH the chamber and magazine. Failure to do so
may result in serious injury and/or damage to property.
Push and Hold the
Base Plate Stop
1
Base Plate
2
Blank Fire Key
4
3
5
0
S
B
Indicator Wheel
7
Blank fire engaged
4
6
Stopper engaged
11
8
AKG 74M
FOLDING STOCK
FIRE SELECTOR SWITCH
1. Safe
In Safe mode the gun will not fire. For safety reasons, you should keep the switch in
Safe mode at all times when you are not ready to fire.
• Press the stock lock button and swing the stock into folding position until it click
into place.
• Press the stock release button to release the stock and swing the stock outward
until it click into position.
0A
Press STOCK
LOCK button
2. Semi-Auto
In Semi-Auto mode the gun will fire one shot for each time you squeeze the trigger.
0A
3. Full Auto
In Full Auto mode the gun will fire continuously as long as the trigger is depressed.
Press STOCK RELEASE button
FRONT SIGHT ADJUSTMENT
0A
• The front sight can be moved up and down to zero the sights.
• Turn counter clockwise to lower the point of Impact.
!
9
WARNING: Do not squeeze the trigger when switching the fire
selector.
!
WARNING! If turned too far, the front sight will come off.
10