Lenco | LED-2411 | Specifications | Lenco LED-2411 24" Full HD Black LED TV

Lenco LED-2411 24
Contents
Introduction
Warning
Caution
Main Unit Description
Remote Control
OSD basic adjustment
DTV Features
USB Features
PVR Opration ( Optional )
Specifications
Trouble Shooting
1
Introduction
Thank you very much for your purchase of our product of LED TV. It serves as a normal
colour TV and PC monitor. To enjoy your TV to the full from the very beginning, read this manual
carefully and keep it handy for ready reference.
INSTALLATION
ķ Locate the TV in a room where direct light does not strike the screen. Totaldarkness or a
reflection on the picture screen can cause eyestrain. Soft and indirectlighting is recommended for
comfortable viewing.
ĸAllow enough space between the receiver and the wall to permit ventilation.
Ĺ Avoid excessively warm locations to prevent possible damage to the cabinet orpremature
component failure.
ĺThis TV can be connected to AC100-240V 50/60HZ.
ĻDo not install the TV in a location near heat sources such as radiator, air ducts,direct sunlight,
or in a place somewhere like close compartment and close area. Do notcover the ventilation
openings when using the TV.
ļ The indicator light will last about 30 seconds to go out after cutting off the electricity, during
this period, you cannot repower it on until the indicator light goes out, thanks a lot for your
attention!
2
Warning
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER- SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to avoid the risk
of electric shock, do not disassemble this equipment by anyone
except a qualified service personnel.
This symbol is intended to alert the user to the presence
of important operation and maintenance instructions in
the literature accompanying the equipment.
3
Caution
Caution
-
High voltages are used in the operation of this product.
Do not open the product's casing. Refer servicing
to qualified service personnel .
Caution
To prevent fire or electrical shock hazard, Do not expose
the main unit to moisture.
Caution
Do not drop or push objects into the television cabinet
slots or openings. Never spill any kind of liquid on the
television receiver.
Caution
Avoid exposing the main unit to direct sunlight and other
sources of heat. Do not stand the television receiver
directly on other products which give off heat. E. g. video
cassette players, Audio amplifiers. Do not block the
ventilation holes in the back cover. Ventilation is essential
to prevent failure of electrical component. Do not squash
power supply cord under the main unit or other heavy objects.
4
Caution
Caution
Never stand on, lean on, push suddenly the product
or its stand. You should Pay special attention to
children.
Caution
Do not place the main unit on an unstable cart stand,
shelf or table. Serious injury to an individual, and
damage to the television, may result if it should fall.
Caution
When the product is not used for an extended period
of time, it is advisable to disconnect the AC power
cord from the AC outlet.
Caution
The LED panel used in this product is made of glass.
Therefore, it can break when the product is dropped
or applied with impact. Be careful not to be injured
by broken glass pieces in case the LED panel breaks.
5
Main unit description
Control Panel Button Function
VOL+ : Volume up.
VOL- : Volume down.
CH+ : TV channel up.
CH- : TV channel down.
MENU : Press to select the main menu.
TV/AV : Select the input signal.
POWER : Switch on when in standby mode or enter the standby mode.
TV Terminal Connections
1. USB input terminal.
2. HDMI input terminal.
3. VGA input terminal of simulation signal of PC.
4. PC AUDIO terminal.
5. SCART terminal.
6. HEADPHONE output terminal.
7. Component (YPbPr\YCbCr) input terminal .
8. Video input terminal.
9. AUDIO input terminal.
10. .ATV antenna/close circuit TV network port or DTV antenna port.
Power Input Configuration
AC
POWER
Optional Configuration as below:
Connect the USB to the USB jack on the set.
6
NOTE
ƽIt is only 500 mA MAX of DC current output when you connect with USB jack
ƽTo ensure the Mobile HD works well, you should use other power supply for the Mobile HD.
And do not use the USB jack in the same time.
ƽ It supports Mobile HD by connecting with USB jack (must more than 2GB). The partitions of
the Mobile HD can’t be more than 4 partitions. The max partition is 2TB. It supports FAT/FAT32
document. The max FAT document is 4GB and the max FAT32 document is 2TB.
7
Remote control
POWER: Power on/off button, press once to turn the TV on
and press again to turn the TV off.
MUTE: Press this button to mute or restore sound.
NICAM/A2: In the TV mode, press this key to select the
sound effects.
SLEEP: Set the sleep timer.
ASPECT: Press to adjust picture ratio.
MEDIA: Press to select the MEDIA signal source.
DISPLAY: Display TV information.
AUTO: Adjust the picture automatically in PC mode.
PMODE: Select picture mode.
SMODE: Select sound mode.
DTV: Press to switch to DTV (Digital TV) mode
SOURCE: Press to open signal source.
MENU: Press this button to enter the main menu.
EXIT: Exit the OSD (On-screen display).
ENTER: Enter the selected option or perform the selected
operation.
0-9: Select and switch to a channel using 0 - 9.
-/--: Display the “Channel List” menu.
: Switch back and front between the current and previous
channels.
CH+/CH-: Change the channel up and down
VOL+/VOL-: Adjust the volume.
INFO: Display some information of current program in DTV
mode.
(Used for models with DTV function only)
AUDIO: Press to select the DTV audio.
(Used for models with DTV function only)
FAV: Switch Favourite List when customer have setted
Favourite channel "
(Used for models with DTV function only)
TV/RADIO: Switch between DTV program and radio
program (Only audio but not image).
(Used for models with DTV function only)
EPG: Enter electronic program guide.
(Used for models with DTV function only)
SUBTITLE: Open or close subtitle.
(Used for models with DTV function only)
8
TEXT: Press to enter or exit the Teletext mode.
(Used for European region only)
INDEX: Press this button to go to the index page in Teletext ˈ
and press this button to display “Record” list in DTV.
(Used for European region only)
HOLD: Freeze a multi-page passage on screen in Teletext mode.
(Used for European region only)
˖Press to play backward.
(Used for models with MEDIA , DTV function only)
SIZE: Display the top, bottom or all of page to read easily in
Teletext mode.
(Used for European region only)
˖Press to play forward.
(Used for models with MEDIA , DTV function only)
REVEAL: Press this button to reveal the hidden information in
Teletext page. Press again to hide the information.
(Used for European region only)
˖Skip to previous chapter
(Used for models with MEDIA , DTV function only)
SUBPAGE: Carry out the function of SUBCODE in the text
while enter the text display mode.
(Used for European region only)
˖Skip to next chapter
(Used for models with MEDIA , DTV function only)
PALY
˖Press to start playing the disc or MEDIA , or to
pause playing.
(Used for models with MEDIA)
STOP ˖Stop playing the disc or MEDIA.
(Used for models with MEDIA , DTV function only)
REPEAT
: Start to record.
( The U disk will be formatted when in burning , please do not
store important files in the U disk )
T.SHIFT: press the button to pause current DTV program and
start record background
RED,GREEN,YELLOW,CYAN:Correspond to the different
menu item colours.
9
OSD basic adjustment
Installation Guide
If this is the first time you are turning on the TV
and there are no programs in the TV memory, the
“Installation Guide” menu will appear on the
screen.
1. Press the “ /!” button to select the local
language.
2. Press “"/#” button to select “Auto Scan” and
press the “!” button or “ENTER” button to enter ,
press “#” button to select start and press
“ENTER” to confirm, or press the “EXIT” button
to exit if necessary.
Note: Searching for platform will take a long time ,
please be patient!
PICTURE
You can select the type of picture, which best corresponds to your viewing.
1. Press the “MENU” button to enter the OSD
menu. Then press “ /!” button to select the
“PICTURE” menu. Enter the “PICTURE”
menu by pressing “#” button or “ENTER”
button.
2. Press “"/#” button to select “Picture Mode”
and press the “ /!” button to select the
picture mode .
3. Press “"/#” button to select “Contrast” and
press the “ /!” button to enter contrast
adjustment menu to adjust contrast.
4. Press “"/#” button to select “Brightness” and press the “ /!” button to enter brightness
adjustment menu to adjust brightness.
5. Press “"/#” button to select “Color” and press the “ /!” button to enter color adjustment
menu to adjust color.
6. Press “"/#” button to select “Sharpness” and press the “ /!” button to enter sharpness
adjustment menu to adjust sharpness.
7. Press “"/#” button to select “Tint” and press the “ /!” button to enter hue adjustment menu
to adjust tint.
Note: The 'Tint' item is used in NTSC mode only
8. Press “"/#” button to select “Color Temperature” and press the “ /!” button to select the
10
color temp.
9. Press “"/#” button to select “Red” and press the “ /!” button to adjust.
10. Press “"/#” button to select “Green” and press the “ /!” button to adjust .
11. Press “"/#” button to select “Blue” and press the “ /!” button to adjust .
12. Press “"/#” button to select “Aspect Ratio” and press the “ /!” button to select the size
which you desire.
Note: When the current source is “PC”, the “Aspect Ratio” item only has two options for
“16:9” and “4:3”.
13. Press “"/#” button to select “Noise Reduction” and press the “ /!” button to select open or
close the noise reduction function .
SOUND
You can select the type of sound, which best
corresponds to your listening.
1. Press the “MENU” button to enter the OSD
menu. Then press “ /!” button to select the
“SOUND” menu. Enter the “SOUND” menu
by pressing “#” button or “ENTER” button.
2. Press “"/#” button to select “Sound Mode”
and press the “ /!” button to select the
sound mode.
3. Press “"/#” button to select “Treble” and
press the “ /!” button to adjust.
4. Press “"/#” button to select “Bass” and press the “ /!” button to adjust.
5. Press “"/#” button to select “Balance” and press the “ /!” button to adjust.
6. Press “"/#” button to select “Auto Volume” and press the “ /!” button to select “On” or
“Off” .This reduces the effect of sudden changes in volume of the source.
7. Press “"/#” button to select “Surround Sound” and press the “ /!” button to select
“Surround” or “Off”.
Note: This creates a surround sound effect, but is not true surround sound.
TIME
1. Press the “MENU” button to enter the OSD
menu. Then press “ /!” button to select the
“TIME” menu. Enter the “TIME” menu by
pressing “#” button or “ENTER” button.
2. Press “"/#” button to select “Clock” and
press the “!” button or “ENTER” button to
enter to setup the local time.
11
3.
4.
5.
6.
7.
Press “"/#” button to select “Off Time” and press the “!” button or “ENTER” button to set
the time at which you want the TV to turn off.
Press “"/#” button to select “On Time” and press the “!” button or “ENTER” button to set
the time at which you want the TV to turn on (from standby mode).
Press “"/#” button to select “Sleep Timer” and press the “ /!” button to select sleep time .
Press “"/#” button to select “Auto Sleep” and press the “ /!” button to select the function
“On” or “Off”.
Press “"/#” button to select “Time Zone” and press the “ /!” button to select the local time
zone.
OPTION
1. Press the “MENU” button to enter the OSD
menu. Then press “ /!” button to select the
“OPTION” menu. Enter the “OPTION”
menu by pressing “#” button or “ENTER”
button.
2. Press “"/#” button to select “Language”
and press the “ /!” button to select the
OSD language which you desire.
3. Press “"/#” button to select “Audio
Language” and press the “!” button or
“ENTER” button to set the “Audio Language”. This function is only used for DTV source.
4. Press “"/#” button to select “Subtitle Language” and press the “!” button or “ENTER”
button to set the “Subtitle Language”. This
function is only used for DTV source.
5. Press “"/#” button to select “Courtry”. The
Country is set to default state., setting is can
not be changed.
6. Press “"/#” button to select “Restore
Setting” menu and press the “!” button or
“ENTER” button to enter. Press the “ /!”
button to select “YES” or “NO”, press
“ENTER” button to reset when select “YES”,
press “ENTER” button to return back to the
previous menu when select “NO”.
12
LOCK
1. Press the “MENU” button to enter the OSD
menu. Then press “ /!” button to select the
“LOCK” menu. Enter the “LOCK” menu by
pressing “#” button. The default password is
“0000”. The administrator password is
“8899”.
2. Press “"/#” button to select “Lock
Channel” and press the “ /!” button to
select “On” or “Off” .Setting to On to close “CHANNEL”MENU and enables Program
Blocking
3. Press “"/#” button to select “Change
Password” and press the “!” button or
“ENTER” button to enter to change
password .
4. Press “"/#” button to select “Block
Programme ” and press the “!” button or
“ENTER” button to enter.
Press “"/#” button to select the item
which you want to lock . Press “GREEN”
button to lock the item and press “GREEN” button
again to unlock. Press “MENU” button to return the
previous menu. Press “EXIT” button to exit the
menu.
5. Press “"/#” button to select “Parental Guidance”
and
6. press the “ /!” button to select “Parental
Guidance” choose rating or turn off .
ATV CHANNEL
1. Press the “MENU” button to enter the OSD menu. Then press “ /!” button to select the
“CHANNEL” menu. Enter the “CHANNEL” menu by pressing “#” button or “ENTER”
button.
2. Press “"/#” button to select “Auto Scan” and press
the “!” button or “ENTER” button to do auto
search . Press “MENU” button to return the previous
menu. Press “EXIT” button to exit.
Note: Searching for platform will take a long time ,
please be patient!
13
3. Press “"/#” button to select “DTV Manual Scan” and press the “!” button or “ENTER”
button to do DTV manual search. Press “MENU” button to return the previous menu. Press
“EXIT” button to exit the menu (This function is only used for DTV source ).
4. Press “"/#” button to select “ATV Manual Scan” and press the “!” button or “ENTER”
button to do ATV manual search. Press “MENU”
button to return the previous menu. Press “EXIT”
button to exit the menu. Press “RED” button to save
the program.
5. Press “"/#” button to select “Programme Edit” and
press the “!” button or “ENTER” button to enter.
a. DELETE
Press “"/#” button to select the program and press
“RED” button twice to delete the program.
b. RENAME
Press “"/#” button to select the program and press
“GREEN” button to rename the program. Press
“ /!” button to select the item which you want to
change and press the “"/#” button to select the
different item . Press “MENU” button to confirm.
c. MOVE
Press “"/#” button to select the channel and press the
“YELLOW” button to MOVE . Then press the “"/#”
button to select the channel with which you want to
MOVE . Press “YELLOW” button again to confirm.
d. SKIP
Press “"/#” button to select the channel which you
want to skip and press the “CYAN” button to skip .
Press “CYAN” button again to cancel the setting.
e. FAV
Press “"/#” button to select the channel
and press the “FAV” button to label the
channel for favourite.
14
PC ˄When signal source is PC˅
1. Press the “MENU” button to enter the OSD menu. Then press “ /! button to select the
“PICTURE” menu. Press “"/#” button to select “PC Setup”. Enter the “PC Setup” menu by
pressing “!” or “ENTER” button.
2. Press “"/#” button to select “Auto Adjust” menu and press the “! button or “ENTER” button
to do auto adjustment.
3. Press “"/#” button to select “Horizontal Pos.” and press the “ /!” button to adjust.
4. Press “"/#” button to select “Vertical Pos.” and press the “ /!” button to adjust.
5. Press “"/#” button to select “Size” and press the “ /!” button to adjust.
6. Press “"/#” button to select “Phase” and press the “ /!” button to adjust.
DTV CHANNEL
1. Press the “MENU” button to enter the OSD menu.
Then press “ /!” button to select the
“CHANNEL” menu. Enter the “CHANNEL” menu
by pressing “#” button or “ENTER” button.
2. Press “"/#” button to select “Auto Scan” and press
the “!” button or “ENTER” button to do auto
search. Press “MENU” button to return the previous
menu. Press “EXIT” button to exit.
Note: Searching for platform will take a long time ,
please be patient!
3. Press “"/#” button to select “DTV Manual Scan” and press the “!” button or “ENTER”
button to do DTV manual search. Press “MENU” button to return the previous menu. Press
“EXIT” button to exit the menu.
4. Press “"/#” button to select “ATV Manual Scan” and press the “!” button or “ENTER”
button to do ATV manual search. Press “MENU” button to return the previous menu. Press
“EXIT” button to exit the menu. Press “RED” button to save the program (This function is
only used for ATV source ).
5. Press “"/#” button to select “Programme Edit” and press the “!” button or “ENTER” button
to enter.
6. Press “"/#” button to select “PVR File System” and press the “!” button or “ENTER”
button to enter.
15
DTV Features
Favourite List
When the source is selected as DTV, users can
enter FAVOURITE LIST by pressing “FAV” button.
The “Favourite LIST” window is illustrated as follows:
Program Information
When the source is selected as DTV, you can
press “INFO” button to display the channel’s
information. The PROGRAM INFORMATION
window is illustrated as follows:
Audio
When the source is selected as DTV, users can
enter “Audio channel” by pressing “AUDIO” button.
The “channel audio” window is illustrated as follows:
Press “ /!” button to select the “Sound Mode” such
as “L&R”, “R&R”, “L&L”.
16
Electronic Program Guide˄EPG˅
Electronic Program Guide provides program information which will be broadcasted now or
in the future. The system will display EPG window by pressing “EPG” button. DATE and TIME
information is displayed on the right of the window. The left side shows all channels. The right
side shows the programs in the channel. The selected program is also displayed on the top of
the screen. When you have selected a program, you can press “INFO” button to display the
program’s detail. Press “YELLOW” button to select the data and press the “ /!” button to
change the day . Press “REPEAT
” button to enter record mode.
Note: The U disk will be formatted when in burning , please do not store important files in
the U disk.
DTV / Radio Switch
“TV / RADIO” button is used to switch between
DTV programs and Digital Radio broadcasts.
Subtitle
When the source is selected as DTV, users can
view subtitles (broadcast dependent)
by pressingĀSUBTITLEābutton.
17
USB Features
1. Press the “MEDIA” button to enter the
“MEDIA” menu.
2. Press the “ /!” button enter the “PHOTO”
option, and press “ENTER” button to confirm .
You can press the “"/#” button to enter the file
of Memory to play the corresponding document,
and then press “ENTER” button to play.
3. Press the “ /!” button to enter the
“MUSIC” option, and press “ENTER” button to confirm . You should press the “"/#” button to
enter the file of Memory to play the corresponding document, and then press “ENTER” button to
play.
4. Press the “ /!”button to play the “MOVIE” option, and press “ENTER” button to confirm .
You should press the “"/#” button to enter the file of Memory to play the corresponding
document, and then press “ENTER” button to play.
5. If you want to save electricity ,press the “CYAN” button to turn off panel power.
6. Press “REPEAT” button to enter repeat mode.
Note: The pics about function are provided for reference only which will be in accordance
with exact circumstances .
18
PVR Opration ( Optional )
1.Press the “MENU” button to enter the OSD
menu. Then press “ /!” button to select the
“CHANNEL” menu . Enter the “CHANNEL” menu
by pressing “#” button or “ENTER” button.
2.Press “"/#” button to select “PVR File System”
and press the “!” button or “ENTER” button to
enter.
a ) Press “"/#” button to select “Select Disk” and press the “!” button or “ENTER” button to
choice disk.
b ) Press “"/#” button to select “Check PVR File
System” and press the “!” button or “ENTER”
button to check PVR file system.
c ) Press “"/#” button to select “Format” and
press the “!” button or “ENTER” button to format
disk.
d ) Press “"/#” button to select “Max record
time” and press the “!” button or “ENTER” button
to select the max record time.
3. Press “"/#” button to select “Recorder Mode”
and press the “!” button or “ENTER” button to enter.
19
4. Press “"/#” button to select “Recorder Schedule List” and press the “!” button or “ENTER”
button to enter.
Note:
1. The U disk will be formatted when in burning , please do not store important files in the U
disk.
2. When you play recording files , press “T.SHIFT” button to paused.
3. Press “ ” button for the first time to start recording, for the second time, the sign of
recorder will be slimmed down, but it's still under recording .
20
SPECIFICATIONS
RGB INPUT
Vertical
Frequency
(HZ)
Mode
Resolution
Horizontal
Frequency
(KHz)
DOS
720x400
31.5
70
VGA
640x480
31.5
60
SVGA
800x600
37.9
60
XGA
1024x768
48.4
60
WXGA
1920 x 1080
67.5
60
HDMI INPUT
Vertical
Frequency
(HZ)
Mode
Resolution
Horizontal
Frequency
(KHz)
VGA
640 x 480
31.47
59.94
480i
720 x480i
15.73
59.94/60
576i
720 x 576i
15.63
50
480p
720 x480p
31.47
59.94/60
576p
720 x 576p
31.26
50
720p
1280 x 720p
37.50
44.96
50
59.94/60
1080i
1920 x 1080i
28.13
33.75
50
59.94/60
1080p
1920 x 1080p
56.25
67.5
50
59.94/60
COMPONENT VIDEO (YPbPr) INPUT
Mode
Resolution
Horizontal Frequency
(KHz)
Vertical Frequency
(HZ)
480i
720 x480i
15.73
59.94/60
576i
720 x 576i
15.63
50
480p
720 x480p
31.47
59.94/60
576p
720 x 576p
31.26
50
720p
1280 x 720p
37.50
44.96
50
59.94/60
1080i
1920 x 1080i
28.13
33.75
50
59.94/60
1080p
1920 x 1080p
56.25
67.5
50
59.94/60
21
Trouble Shooting
Before consulting service personnel, check the following chart for possible solutions.
PROBLEM
TV will not turn on
SOLUTION
ƽMake sure the power cord is plugged in.
ƽThe batteries in the remote control may be
Exhausted ; replace the batteries.
ƽCheck the cable between TV and antenna/ external AV
device.
No picture, no sound
ƽPress the power button on the remote.
ƽPress the SOURCE button the remote, then press the
Ā /!ābutton repeatedly to select the TV source.
ƽCheck the cable between TV and antenna/ external AV
device.
Poor picture, sound OK
ƽTry another channel, the station may have broadcast
difficulties.
ƽAdjust the brightness/contrast in the Video menu. Check
that the unit is set to PAL
Audio noise
ƽMove any infrared equipment away from the TV.
The LED panel uses a panel consisting of sub pixels which requires sophisticated technology to
produce. However, there may be a small number of bright or dark pixels on the screen. These pixels
will have no impact on the performance of the product.
22
If at any time in the future you should need to dispose of this product please
note that: Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or retailer for
recycling advice. (Waste Electrical and Electronic Equipment Directive)
23
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising