HD51P/PX Operation Manual

Add to my manuals
33 Pages

advertisement

HD51P/PX Operation Manual | Manualzz
 à READ AND KEEP THIS OPERATION MANUAL
Honeywell
Operation Manual
COLOR DOME CAMERA
HD51P/PX series
CCD,
DIGITAL COLOR
800-07009-B 07/11
Honeywell
Warnings
Installation and servicing should be performed only by qualified and experienced personnel
to conform to all local codes and to maintain your warranty.
WARNING! 12V DC models require the use of CSA Certified/UL Listed
Class 2 power adapters to ensure compliance with electrical
safety standards.
WEEE (Waste Electrical and Electronic Equipment).
Correct disposal of this product (applicable in the European Union and
other European countries with separate collection systems).
This product should be disposed of, at the end of its useful life, as per
E applicable local laws, regulations, and procedures.
FCC Compliance Statement
Information to the User: This equipment has been tested and found to comply with the limits
for a Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed
to provide reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area
Is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Caution Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Manufacturer's Declaration of Conformance
The manufacturer declares that the equipment supplied with this guide is compliant with the
essential protection requirements of the EMC Directive 2004/108/EC and the General Product Safety
Directive GPSD 2001/95/EC, conforming to the requirements of standards EN 55022 for emissions,
EN 50130-4 for immunity, and EN 60950 for Electrical Equipment safety.
WARNING: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Need Help?
Call 1.800.796.CCTV for sales, service and customer support.
www. honeywellvideo.com
J m
CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of un-Insulated "dangerous voltage” within the products enclosure
that may be of sufficient magnitude to constitute a risk of electric shock t&o persons.
>
The exclamation point within an equilateral triangle Is intended to alert the user to the presence
of important operating instructions in the literature accompanying the appliance.
>
Thank you for purchasing this COLOR VIDEO CAMERA.
Before using this camera, please read this operation manual carefully
to obtain the best result and keep this manual for future reference.
. SAFETY INSTRUCTIONS -----------------------=—emeeennen one EEE EEE EEE EEE EEE
. PRECAUTIONS -------------==-neeeeoraneona enanos
. FEATURES ----——=—=e—=nmennana nana naaa nannno nan enann enana nana enana anna nana nana
. SUPPLIED ACCESSORIES --------------------0--0eeeenennonnaon nen nan
INSTALLATION -----------<......ercereceorereseeeeseere rare esenee sera eaeacene ace
. NAME AND FUNCTIONS -----------------=-====eeeeeenoo nen EEE EEE EEE
. CONNECTIONS -------------------eeeeoneen ones
. OPERATING CAMERA ----------------------==-=-e=-eeeeeeeenen ene nemnee,
Yo {To (oS
10. TROUBLESHOOTING ------------=mssssmeassmemsamemsmamemsememsamame mens ame mame nenace.
© © ~N a AL UN =
Read Instructions
+
Read all of the safety and operating Instructions
before using the product.
Retain Instructions
Save these instructions for later use.
Cleaning.
Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
Power source
+
This product should be operated only from
a 12V DC power source as indicated on the
marking label.
о Do not install the camera in extreme temperature conditions.
Operate the camera under conditions where temperatures are within +14°F to +122°F (-10°C to +50°C).
Ensure there is enough ventilation in high temperature environments.
9 Do not disassemble the camera.
There are no user repairable parts inside.
2 Do not drop the camera or subject them to physical shocks.
It can cause malfunctions to occur.
9 Never keep the camera face to strong light directly.
It can damage CCD.
NOTE When this camera is installed near wireless communication devices
that emit strong electromagnetic field, irregularity such as noise
on the monitor may appear.
1/3” High Sensitivity CCD
Min lllumination (F1.4, 50 IRE, AGC Max)
- 0.3 LUX (COLOR)
User-friendly menus
- Ultra High Resolution (600 TVL)
- SBLC (Super Back Light Compensation)
- DNR (Digital Moise Reduction)
- Privacy zone selectable
- Mirror (Horizontal)
- Flickerless On/Off
LAA
Service Monitor Cable
я -
( .
TN
\_ b Guide Pattern
©
9 a =
Stick the guide pattern on the wall or ceiling and mark Ceiling
the mounting holes.
Drill four holes according to the guide pattern, then insert
anchors into the drilled holes.
> Guide Pattern
P Rubber
Attach the camera base to the ceiling or wall using f à
the supplied four screws. J » Dome Base
Aim and focus by tuming and moving the 3-axis camera / /
bracket by hand. / / * Mounting Screw
Align the dome cover over the base.
EEE EEE EEE EEF EEE EEE EEE EEE IEEE EEE EEE TE E Dome Cover
Secure the dome cover to the base using the supplied
L-wrench.
L-Wrench
CD” Camera Layout JF,
D Tilt rotation : Adjusting the vertical angle. :
(2 Pan rotation : Adjusting the horizontal angle. :
(3) Horizontal rotation : Adjusting the horizontal :
position of the screen. :
(A) Focus handle : Focus (Far or Near)
(5) Zoom handle: Zoom (Tele or Wide)
1. Connecting to Monitor and Power
- Connect the video-out jack of the camera to the video-in jack of the monitor using a BNC cable.
- Connect the power adapter to the power input connector.
- Use 12V DC power source.
Remark
Video Output Yellow 10Vp.p
#2| Power Input Red 12V DC(+10%), Max 2.2 W/180 mA
4
O 8. OPERATING CAMERA
BRIGHTNESS
FLE,
О-20
a ELK
SHUTTER
RED
BLUE
WHITE BAL MANUAL
0-160
ON LEVEL
AGC
DAY / NIGHT
OFF LOW, MIDD
OFF LOW, MIDD
HIGH
HIGH
0~20
IMAGE ADJ
1-24
TOP 8-126 | 10~146
IMAGE ADJ MOTION BOTTOM B--126 / 11-149
(NTSC/PAL) LEFT 4-191 / 8191
4.191 /9-192
RETURN +
13
1-4
4-63 / 6-74
9-64 / P75
18-205 / 22-206
19-206 / 23-207
PRIVACY
(NTSC/PAL)
4
0-0
0-0
COLOR GAIN
+!
CAM TITLE
VERSION
Use the joystick to navigate through the menus. MAIN MENU - GENERAL
Press MENU button to access the SETUP menu.
Select each sub-menu by using the q». A, Y button.
Press the MENU(SET) button to select.
… as ii i
3 ESC + i
+ VINE DAL ATW 3:
i AGC ON + À
,[ ;Ç + IMAGE +! :
@ DOWN : Move down / (9 UP: Move up E GENERAL = $
O LEFT : Move left INITIAL ON Ei
E) RIGHT : Move right "Е EXIT + 1
O MENU(SET):
Press the Joystick in its straight position.
@ Sevice Monitor Connecter :
Use service monitor connector to set camera
F
- Cpe a
rey EE EEE ERENT ETE FSFE NESE REFEREE RNA я
A OR E ON LA LA TI NE NL
If the OSD MENU is changed then INITIAL will be OFF
angle & focus when installing. (EXCEPT : LENS)
Press the MENU button to access the SETUP menu.
stress pan pire pu née en ane <
Г. Bull BEE EEE EEE FFE EEE EEE EEE EEE EEE AE :
x т = в
E
E
ta LENS DC a
Select DC and press the MENU button to have Hi DC LEVEL | i:
LENS DC activated. | tac or; $
| SHUTTER 1/60(50) |
1. DC LEVEL (Adjusts brightness of the image.)
- Select DC LEVEL using the UP or DOWN button. You can adjust between 0 to 20 level using
the LEFT or RIGHT button.
2. FLK (FLICKERLESS)
- Select FLK using the UP or DOWN button. You can select between ON / OFF using the LEFT or
RIGHT button.
> OFF : You will be allowed to adjust the shutter speed.
3. SHUTTER (Adjusts the shutter speed of the lens.)
- Select SHUTTER using the UP or DOWN button. You can adjust from 1/60(1/50), 1/120(1/100),
1/250, 1/500, 1/700, 1/1kK, 1/1600, 1/2500, 1/6K, 1/7K, 1/10kK, 1/30K, 1/60K, 1/120K(sec) level
using the LEFT or RIGHT button.
WHITE BAL (White Balance)
=
clar
Select WHITE BAL using the UP or DOWN button. You can select from ATW, MANUAL,
PUSH using the LEFT or RIGHT button.
1. ATW : Color temperature is automatically adjusted for light sources in the 2,000°K to 10,000°K range
2. MANUAL : To adjust the white balance manually
- Select MANUAL using the UP or DOWN button and press the MENU button to activate WB MANUAL
option.
a E A E WEEE
" AE EE EEE == A A
+
ги EEE AEREA +
: RED | $
1 Mi
НОВЫЕ FA i
4 EXIT - MENU +
„+ ET н “oll |
i
FETE ERE EERE EER EEE canes EATER
EEE EEE ERRE
1. RED : To adjust density of RED (0 to 160)
2. BLUE : To adjust density of BLUE (0 to 160)
3. PUSH : Push Lock mode fixes the white balance based on current lighting. For best results,
place a white surface (such as a piece of paper) in front of the camera during adjustment.
AGC (Automatic Gain Control )
select AGC using the UP or DOWN button. You can select between OFF, ON using the
LEFT or RIGHT button.
1. ON : Select ON using the LEFT or RIGHT button and press the MENU button to activate
the AGC option.
= a ;
= E
* в
i ä
nr a
= E
=
= all nN
a Pues FR DR BR ER ETE +
EERE AFFERENTS RAR RFE FEARS RAPP REE
1. LEVEL : You can adjust between О 10 20 using the LEFT or RIGHT button.
2. OFF : Disable the AGC
20
IMAGE ADJ (Image Adjust)
Select IMAGE ADJ using the UP or DOWN button and press the MENU button to activate
the IMAGE ADJ mode.
LISSA ОеаайаеаааЕ ~~
: ul IMAGE ADJ
E SBLC OFF
i § DNR LOW
+ SHARPNESS +
Е MIRROR OFF
.i MOTION +
+ PRIVACY +
4 COLOR GAIN +!
: GAMMA 0.45 :
: INITIAL ON
- ETT 0 -
1. SBLC (Super Back Light Compensation) : To lighten a darker part of the image
- Select SBLC using the UP or DOWN button. You can select between OFF, LOW, MIDDLE,
HIGH using the LEFT or RIGHT button.
- SBLC turns to OFF automatically at night.
2. DNR (Digital Noise Reduction) : To reduce the image noise especially during low ambient
lighting conditions.
- Select DNR using the UP or DOWN button. You can adjust between OFF, LOW MIDDLE, HIGH
using the LEFT or RIGHT button.
3. SHARPNESS : To adjust SHARFMESS of the image.
- Select SHARPNESS using the UP or DOWN button.
- Select « and press the MENU button to activate
SHARPNESS option.
- You can adjust the sharpness from 0 to 20 using the
LEFT or RIGHT button.
4. MIRROR
- Select MIRROR using the UP or DOWN button.
You can select from ON/OFF using the LEFT or RIGHT
button.
(1) ON : Horizontal image flip.
(2) OFF : default
5. MOTION (Motion Detect) Display only (No output signal)
- Select MOTION using the UP or DOWN button and
press MENU button to activate the MOTION DETECT
option.
E re О °
3 -
Ш |: 3
P EXIT - MENU р 3
Speers ETE rr Treas
NTSC(PAL)
AA‘
i:
1 i
oF IE:
5 +
19 (27 ..
27 i
13(25)
80 (95) |.
oN i
al +
1) AREA : To specify MOTION DETECTION area
- Select AREA using the UP or DOWN button.
You can select from area 1 to 4 position using the LEFT or RIGHT button.
2) DISPLAY : To display MOTION DETECTED area on the video — N )
- Select DISPLAY using the UP or DOWN button. | | 1
You can select between ON/OFF using the LEFT or RIGHT button.
(1) ON : display the MOTION DETECTED area on the screen
(2) OFF : disable
= EA
3) SENSITIVITY : To set up the motion sensitivity
- Select SENSITIVITY using the UP or DOWN button.
You can adjust the motion sensitivity of a movement from 1 to 24 using the LEFT or RIGHT button.
(1) 1: most sensitive (highest)
(2) 24 : least sensitive (lowest)
4) TOP / BOTTOM / LEFT / RIGHT : Users can specify MOTION DETECTED area.
- Select TOP, BOTTOM, LEFT, or RIGHT using the UP or DOWN button. You can adjust the AREA
using the LEFT or RIGHT button.
(NTSC/PAL)
(1) TOP : extend or reduce the upper area of the MOTION DETECTED area (8 to 126 / 10 to 146)
(2) BOTTOM : extend or reduce the bottom area of the MOTION DETECTED area (8 to126/ 11 to 149)
(3) LEFT : extend or reduce the left side of the MOTION DETECTED area (4 to 191 / 810191)
(4) RIGHT : extend or reduce the right side of the MOTION DETECTED area (4 to 191 /9to 192)
TOP reduce RIGHT extend
ge) '
a Gt an FEET EEE EE mE ona a ~
' # ue ; ,
u E il
LEFT & 1 RIGHT Ÿ +
; i — |! lem | =;
i + ; :
AR EA Re, i ;
Е J 05
BOTTOM '
5) INITIAL : To reset the MOTION DETECT mode.
- Select INITIAL using the UP or DOWN button. You can reset the MOTION DETECT mode using
the MENU button.
6) RETURN :To return to IMAGE ADJ MENU
- Select RETURN using the UP or DOWN button. You can return to IMAGE ADJ MENU using
the MENU button.
y
i
-
a
-
6. PRIVACY
- select PRIVACY using the UP or DOWN button and
press the MENU button to active the PRIVACY option.
1) AREA : To specify the PRIVACY area
- Select AREA using the UP or DOWN button. You can
select area from 1 to 4 position using the LEFT or RIGHT
button.
2) DISPLAY : To display the Privacy Zone area
- Select DISPLAY using the UP or DOWN button. You can
select between ON/OFF using the LEFT or RIGHT button.
(1) ON : display the Privacy Zone area
(2) OFF : disable
3) COLOR : To change the color of the privacy zone
- Select COLOR using the UP or DOWN button.
You can adjust from WHITE, YELLOW, GREEN, BLUE, RED,
BLACK, or GRAY using the LEFT or RIGHT button.
HERE nee
ñ = fC i
=
a A
и я = = LL В
PRIVACY
AREA 1
DISPLAY OFF
COLOR WHITE
TOP 15 (16)
BOTTOM 31 (38
LEFT 44
RIGHT 104
INITIAL ON
RETURN +
©
B
4) TOP / BOTTOM / LEFT / RIGHT : Users can specify a PRIVACY ZONE area
- Select TOP, BOTTOM, LEFT, or RIGHT using the UP or DOWN button. You can adjust the privacy
zone using the LEFT or RIGHT button.
(NTSC/PAL)
(1) TOP : extend or reduce the upper area of the PRIVACY area (4 to 63 / 6 to 74)
(2) BOTTOM : extend or reduce the bottom area of the PHIVACY area (5 to 64 / 7 to 75)
(3) LEFT : extend or reduce the left side of the PRIVACY area (18 to 205 / 22 to 206)
(4) RIGHT : extend or reduce the right side of the PRIVACY area (19 to 206 / 23 to 207)
TOP reduce RIGHT extend
:
tr “=== $ 0008 res
8 4 LL :
LEFT € 1 € RIGHT Ч i
т ; N
Mi... 1 MB ;
Вс. + A ь
BOTTOM
5) INITIAL : To reset to factory default only on the PRIVACY mode.
- Select INITIAL using the UP or DOWN button. You can reset the PRIVACY mode using the MENU
button.
6) RETURN :To return to IMAGE ADJ MENU
- Select RETURN using the UP or DOWN button. You can return to IMAGE ADJ MENU using the MENU
button.
E
7. COLOR GAIN
- Select COLOR GAIN using the UP or DOWN button and
then press the MENU button to activate the COLOR MODE
option.
8. GAMMA
- When you use CRT or LCD monitor, you can select between
0.35, 0.45, 0.6, 0.75, using the LEFT or RIGHT button.
9. INITIAL :
To reset to factory default only on the IMAGE ADJ mode.
- Select INITIAL using the UP or DOWN button and reset
the IMAGE ADJ mode using the MENU button.
10. RETURN :
To return to MAIN MENU
- Select RETURN using the UP or DOWN button and return
to MENU using the MENU button.
|
|
Ш.
COLOR GAIN |
ео НО
er Hs
0 E Г
RY: -- To adjust density of RED (0 to 201
B-Y : To adjust density of BLUE (0 to 20)
| GENERAL Fu
3 GENERAL
Select GENERAL using the UP or DOWN button and | SI a TITLE
press the MENU button to activate the GENERAL mode. i ei
110 RETURN
te PA AA
1. CAM TITLE ¡MU ei LES 1
- Select CAM TITLE using the UP or DOWN button. HE
You can adjust ON/OFF using the LEFT or RIGHT button. ‘8
(1) ON : To display the camera title on the screen Е
(2) OFF : disable 3 LEI - POSITION
E EXIT - MENU
- Select ON and Press MENU button to display CAM TITLE. ees
(1) UF/DN : To select character using the UP or DOWN button (0 to 9,4 to Z)
(2) LE/RI : To select position using the LEFT or RIGHT button.
2. LANGUAGE - English LANGUAGE.
3. VERSION - Displays the firmware version.
4. INITIAL : To reset to factory default only on the GENERAL mode.
- Select INITIAL using the UP or DOWN button.
You can reset to factory default for GENERAL mode using the MENU button.
5. RETURN : To return to MENU
- Select RETURN using the UP or DOWN button. You can return to the MENU using the MENU button.
(EN: V 0 - To reset to factory default.
- Select INITIAL using the UP or DOWN button and reset to factory default using the MENU button.
SAI : To exit the OSD setup menu.
- Select EXIT using the UP or DOWN button and close the OSD setup menu by pressing the MENU
button.
30
O 9. SPECIFICATION
MODEL
Signal System
Image Sensor
HIGH RESOLUTION
NTSC PAL
1/3” High Sensitivity CCD
Effective Рон 752H)x582)
Video Output
Sync. System
S/N Ratio
Horizontal Resolution
Min lllumination
(F1.4, 50 IRE, AGC Max)
Composite : 1.0V p-p, 75 Ohms
Internal Sync
50 dB Min. (SHARPNESS, AGC off)
800 TVLines
0.3 Lux (Color)
ESC 50 - 120,000
Manual Shutter
DNR
1/ 80(1/50), 1/120(1/100), 1/ 250, 1/ 500, 1/ 700, 1/ 1K,
1/ 1.6K, 1/ 2.5K, 1/ 5K, 1/ 7K, 1/ 10K, 1/ 30K, 1/ 60K, 1/ 120K
OFF, LOW, MIDDLE, HIGH
White Balance
SBLC
AGC
Motion Detection
Privacy
Mirror
sharpness
GAMMA
OSD Language
Applicable Lens
supply Voltage
Power Consumption
Operating Temperature/ Humidity
Storage Temperature/ Humidity
ATW, MANUAL , PUSH
OFF, LOW, MIDDLE, HIGH
ON, OFF, selectable
ON, OFF (4 Programmable Zone)
ON, OFF (4 Programmable Zone)
ON (HORIZONTAL), OFF
1to 20
0.35, 0.45, 0.6, 0.75
English
DC Iris Lens
12V DC (+10 %)
180 mA / 2.2 W (Max)
+14°F to +122°F (-10°C to +50°C) / 30% to 80% RH
-4°F to +140°F (-20°C to +00°C) / 20% to 00% RH
31
If you have trouble operating your camera, refer to the following guidelines. If the guidelines do
not help you to solve the problem, contact an authorized technician.
Nothing appears on the screen
Y Check that the power cord and the video cable between the camera and monitor are properly connected.
+" Check that you have properly connected the VIDEO cable to the camera VIDEO output jack.
The image on the screen is dim
+" If the lens is obstructed (for example, with dirt), clean the lens with a soft, clean cloth.
Y Set the monitor to proper condition.
Y |f the camera is exposed to too strong light, change the camera position.
+" Adjust the lens’ focus properly.
The image on the screen is dark
+ Adjust the contrast feature of the monitor.
+ If you loop through an intermediate device, set the termination (75 Ohms / Hi-Z) properly.
3-AXIS
COLOR DOME CAMERA
Need Help”
Call 1.800.796.CCTV for sales, service and customer support.
www.honeywellvideo.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement