Scosche CJ1278B mounting kit Manual

Add to my manuals
8 Pages

advertisement

Scosche CJ1278B mounting kit Manual | Manualzz
1996-98
CJ1278
Jeep Grand Cherokee
Read pages 2-4 for kit assembly.
Radio Removal:
1.
2.
3.
4.
5.
Extract (5) screws from along top of dash instrument bezel.
Carefully pop out wood grain trim panel around a/c heater control.
Carefully pop out wood grain trim panel around headlight switch.
Extract (4) screws from along bottom of dash instrument bezel, lift up and away to remove.
Extract (2) 3/8" hex heard bolts holding radio, unplug connectors and remove.
USE THESE SUPPORT
TABS AS REQUIRED
IN-DASH INSTALLATION KIT
FOR SELECT 1974-UP CHRYSLER AND JEEP
VEHICLES
REMOVE
ALIGNMENT
PIN - BOTTOM
TABLE OF CONTENTS
CHRYSLER
DODGE
1995-00
CIRRUS .......................... 4
1995-00
AVENGER .................... 10
1993-97
CONCORDE .................. 5
1996-00
CARAVAN .................... 11
1980-83
CORDOBA ..................... 5
1994-95
CARAVAN .................... 11
JEEP
1975-79
CORDOBA ..................... 6
1991-93
CARAVAN .................... 12
1996-98
1990-93
FIFTH AVENUE ............. 6
1984-90
CARAVAN .................... 12
1993-95
GRAND CHEROKEE ... 16
1979-89
FIFTH AVENUE ............. 7
1997-00
DAKOTA ....................... 13
1997-02
WRANGLER ................. 16
Radio Removal:
1990-93
IMPERIAL ....................... 6
1990-93
DAYTONA .................... 13
1. Extract two screws from above the radio securing the radio trim bezel.
2. Extract two screws from above the diagnostics display panel securing the
radio trim bezel.
USE THESE
3. Carefully remove the ashtray and extract two
SUPPORT TABS
screws located in the ashtray cavity securing the AS REQUIRED
radio trim bezel.
4. Pull the radio trim bezel away from the dash,
unplug all connectors and remove the bezel.
5. Extract two nuts securing the radio to the dash,
and pull the radio from the cavity; unplug all
connectors and remove the radio.
1981-83
IMPERIAL ....................... 8
1977-89
DIPLOMAT ..................... 7
PLYMOUTH
1984-86
LASER ............................ 8
1998-00
DURANGO ................... 13
1989-95
ACCLAIM ...................... 15
1977-81
LE BARON ..................... 7
1988-93
DYNASTY ....................... 6
1975-77
FURY .............................. 6
1987-93
LE BARON "COUPE" ..... 9
1993-97
INTREPID ....................... 4
1984-89
GRAN FURY .................. 7
1994-97
LHS ................................. 9
1980-83
MIRADA .......................... 5
1975-79
GRAN FURY ................ 10
1979-81
NEWPORT ..................... 8
1995-99
NEON ........................... 14
1995-99
NEON ........................... 14
1975-78
NEWPORT ................... 10
1998-01
RAM .............................. 14
1987-94
SUNDANCE ................. 15
1994-96
NEW YORKER ............... 9
1978-02
RAM VAN ...................... 15
1978-83
VAN .............................. 15
1988-93
NEW YORKER ............... 6
1994-97
RAM PICKUP ............... 14
1996-00
VOYAGER .................... 11
1984-87
NEW YORKER ............... 7
1975-77
ROYAL MONACO ........ 10
1994-95
VOYAGER .................... 11
1979-83
NEW YORKER ............... 8
1987-94
SHADOW ..................... 15
1991-93
VOYAGER .................... 12
1975-78
NEW YORKER ............. 10
1989-95
SPIRIT .......................... 16
1984-90
VOYAGER .................... 12
1996-00
SEBRING JX
1995-00
STRATUS ....................... 4
CONVERTIBLE .............. 4
1979-81
ST. REGIS ...................... 8
1995-00
SEBRING ..................... 10
1996-00
TOWN & COUNTRY .... 11
1994-95
TOWN & COUNTRY .... 11
1991-93
TOWN & COUNTRY .... 12
1990
TOWN & COUNTRY .... 12
USE THIS BRACKET
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
1993-95 Jeep Grand Cherokee
Read pages 2-4 for kit assembly.
USE THIS
BRACKET
(TOP)
USE THIS BRACKET
(BOTTOM)
USE THESE
SUPPORT TABS
AS REQUIRED
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
1997-02
Read pages 2-4 for kit assembly.
Jeep Wrangler
Radio Removal:
1. Extract (2) screws from dash bezel.
2. Pry on bezel to release spring clips and
remove.
3. Extract (2) screws holding radio, unplug
and remove.
USE THESE
SUPPORT TABS
AS REQUIRED
REMOVE
ALIGNMENT
PIN - BOTTOM
EAGLE
1993-97
VISION ........................... 5
GRAND CHEROKEE ... 16
CAR STEREO CONNECTORS
USE THIS
BRACKET
PROVIDE EASY
CONNECTION OF
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
YOUR CAR STEREO TO
FACTORY WIRING
HARNESS.
1989-95 Plymouth Acclaim
Read pages 2-4 for kit assembly.
CR01
Radio Removal:
1984-up Chrysler vehicles.
1. Carefully release the spring clips securing the radio/dash trim: three clips along the top
and two at the bottom. Disconnect the panel light and remove the trim piece.
2. Extract the two bolts securing the radio: one at
USE THESE
the top right, and one at the bottom left of the
SUPPORT TABS
AS REQUIRED
radio.
3. Pull the radio out of the dash cavity, disconnect
the antenna and all electrical connections, and
USE THIS
remove the radio.
BRACKET
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
16
LIABILITY DISCLAIMER
This instruction booklet is based on carefully documented data and research of automobile dash disassembly, wire harness/codes and information pertaining to installation of this kit (#CJ1278) in 1974-UP in Select
Chrysler and Jeep Vehicles. Scosche Industries, Inc. can not be held responsible for discrepancies/
inconsistencies that may occur due to the automobile manufacturing changes or options, or damage that
may occur in the automobile during the installation of components while using this booklet.
If you have any further questions, call
© 2005 SCOSCHE INDUSTRIES, INC.
TECH HELP 1-800-621-3695, ext. 3
SI 8/05 CJ1278 (3000356)
INTRODUCTION
The Scosche in-Dash Installation Kit for 1974-UP Chrysler and Jeep Vehicles provides the parts you need to
mount your car stereo/cassette player into your vehicle's dash. Refer to the individual instructions in this
manual to remove your vehicle's factory installed radio.
PRELIMINARY PARTS LIST
Your kit includes:
• 1 Mounting Panel
• 2 Snap Shaft Brackets
• 1 ISO Trim Ring
• 2 Spacers
• 2 ISO Mount Brackets
• 1 Snap-In Pocket
Read pages 2-4 for kit assembly.
1978-02 Dodge Ram Van
1978-83 Plymouth Van
Radio Removal:
1. Remove two screws securing the dash panel inside the glove box.
2. Remove four screws from the bottom edge of the dash panel and
one on the left side of the panel.
3. Carefully pull the panel from the dash and remove the panel.
4. Remove two screws securing the radio
USE THESE
SUPPORT TABS
to the dash. Pull the radio out.
AS REQUIRED
5. Disconnect power, antenna, and all
speaker and electrical connections.
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
CAUTION:
Disconnect your vehicle's negative battery terminal before the installation to help prevent electrical
damage. We recommend the use of a volt/ohm meter over a test light to check wiring. A test light or
grounded wire probe can cause damage to the vehicle's computer and/or diagnostic systems. Avoid all
factory airbag wiring. Airbags can accidentally deploy causing serious injury or death.
USE THIS
BRACKET
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
NOTES:
• See your vehicle's instructions for any special tools your installation might require.
• Read all instructions accompanying your car stereo/cassette player for proper wiring
and mounting instructions.
Read pages 2-4 for kit assembly.
1987-94 Dodge Shadow
1987-94 Plymouth Sundance
Radio Removal:
WIRE CODES
NOTE:For Factory WIring Codes go to:
www.scosche-cars.com
ASSEMBLING THE KIT
The instructions for each vehicle show which mounting panel
and brackets to use.
Use the shaded mounting tabs and indicated brackets. Carefully
break or cut off the unused brackets. Then assemble the radio
and the mounting panel as shown below, and secure the kit to
your dash using the supplied screws. Reassemble your dash,
and attach the radio's front panel and controls.
The following example shows a typical installation.
1. Remove the ashtray
2. Carefully pull outward on the edges of the trim panel to release
the snaps, and remove the panel.
3. Remove one retaining screw from above the right upper corner of
the radio.
4. Pull the dash trim towards the passenger side to gain access to
the upper right radio bolt; remove the top
USE THESE
right bolt and the lower left bolt.
SUPPORT TABS
AS REQUIRED
5. Pull out the radio. Disconnect the power,
antenna, speaker leads, and all other
electrical connections. Remove the radio.
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
1989-95 Dodge Spirit
ASSEMBLING THE POCKET
REMOVE
ALIGNMENT
PIN - BOTTOM
Read pages 2-4 for kit assembly.
Radio Removal:
1. Carefully release the spring type fasteners from the radio/console trim
panel - three from along the top and two from the bottom of the panel.
2. Remove two screws from along the top of the side console trim pieces,
and spread the side piece out slightly for access to the radio bolt.
3. After spreading the side piece, extract the top
right radio mounting bolt, then remove the
USE THESE
SUPPORT TABS
bottom left bolt.
AS REQUIRED
4. Spread the side piece once again to provide
clearance for pulling the radio out of the
cavity; pull the radio out, disconnect the
USE THIS
BRACKET
connectors, and remove the radio.
1. Locate and align bottom guides and top snaps of
the pocket to kit panel.
2. Slide pocket on bottom guides while the top
snaps are aligned.
3. When aligned properly, the top pocket snaps will
lock to kit panel.
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
15
2
15
ASSEMBLING THE KIT (Cont'd)
1995-99 Dodge Neon
1995-99 Plymouth Neon
Read pages 2-4 for kit assembly.
SHAFT MOUNT (DIN-C) RADIOS
Using the radio's knobs/hardware, secure the radio to the mounting panel and to the shaft radio faceplate as
shown.
Radio Removal:
1. Remove the ashtray from the dash.
2. Carefully pry outward on the radio trim bezel to release spring
clips then remove.
3. Extract the two 3/8" screws securing the radio to the dash, pull
the radio from the dash cavity, unplug all connectors,
disconnect the ground strap and remove the radio.
CAUTION:
REAR SUPPORTING THE RADIO ADDS TO
THE INSTALLATION'S STRUCTURAL
INTEGRITY.
REMOVE
ALIGNMENT
PIN - BOTTOM
CJ1278
MOUNTING
PANEL
USE THIS
BRACKET
REAR
SUPPORT
STRAP
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
1998-01 Dodge Ram
Read pages 2-4 for kit assembly.
SNAP SHAFT TABS
Radio Radio:
SHAFT RADIO
SPACER (OPTIONAL)
1. Extract (1) Screw from lighter socket area.
2. Carefully pryout on the radio dash bezel to release the fastening
clips, disconnect all connectors and remove the bezel.
3. Extract the (2) screws securing the radio to the dash,
pull the radio from the dash cavity, unplug all
connectors, diconnect the ground strap and remove the radio.
SUPPLIED WITH
YOUR NEW RADIO
DIN-ISO MOUNT: (DIN-E Radio with Side Mounting Holes)
USE THESE
SUPPORT TABS
AS REQUIRED
1. Snap the DIN iso side mounting brackets to the back of the mounting panel (1 left and
1 right). Use supplied hardware to bolt them to the back of the kit panel.
2. Snap the DIN-ISO Trim Ring into the radio opening.
3. Load the Radio from the REAR of the mounting panel until the nosepiece of
the radio comes through the front of the kit.
4. Use the 5MM screws to secure the radio from the sides.
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
REAR
SUPPORT
STRAP
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
1994-97 Dodge Ram Pickup
Read pages 2-4 for kit assembly.
Radio Removal:
1. Remove the ashtray from the dash, extract the two screws securing the ashtray bracket to the
dash and remove the bracket.
2. Open up the cup holder and extract the two screws securing it to the dash.
3. Carefully pry out on the perimeter radio dash bezel using a panel removal tool to release the
fastening clips, disconnect all connectors and remove the bezel.
4. Extract the two screws securing the radio to the dash, pull the radio from the dash cavity, unplug
all connectors, disconnect the ground strap and remove the radio.
USE THESE
SUPPORT TABS
AS REQUIRED
CAUTION:
REAR SUPPORTING THE RADIO ADDS TO
THE INSTALLATION'S STRUCTURAL
INTEGRITY.
DIN RADIO
5MM SCREWS
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
CJ1278
ISO
MOUNTING
BRACKETS
CJ1278
TRIM RING
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
14
3
CJ1278
MOUNTING
PANEL
ASSEMBLING THE KIT (Cont'd)
The kit panel comes DIN ready. Follow the instructions supplied with the radio, secure the mounting kit.
Install the assembly in the dash and use the rear support strap supplied with the radio to support the
rear of the radio.
REAR
SUPPORT
STRAP
CAUTION:
REAR SUPPORTING THE RADIO ADDS TO
THE INSTALLATION'S STRUCTURAL
INTEGRITY.
Read pages 2-4 for kit assembly.
1998-00 Dodge Durango
1997-00 Dodge Dakota
IN-DASH DIN PULLOUT, DETACHABLE FACEPLATE, (DIN-E) RADIOS
Radio Removal:
1. Remove eight screws from the dash trim panel.
2. Remove two screws from the underside of the
steering column trim, and remove the trim.
3. Remove two screws from the radio mounting
bracket, disconnect power antenna, speaker
leads, and all other electrical connections, and
remove the radio.
USE THESE
SUPPORT TABS
AS REQUIRED
RADIO'S
SUPPLIED
TRIMPLATE
REMOVE
ALIGNMENT
PIN - BOTTOM
CJ1278
MOUNTING
PANEL
RADIO'S
MOUNTING
SLEEVE
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
DIN RADIO
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
Read pages 2-4 for kit assembly.
1995-00
1995-00
1995-00
Chrysler Cirrus
Chrysler Sebring JX Convertible
Dodge Stratus
Read pages 2-4 for kit assembly.
1990-93 Dodge Daytona
Radio Removal:
1. Pull firmly outward on the console/radio trim panel secured by five metal spring clips, two at the top, two on
the right side and one on the left side.
2. Extract the top two screws from each side of the lower
console - this allows you to slightly spread the console,
providing clearance to remove the radio.
3. Remove the remaining two screws securing the radio,
disconnect the connectors and remove the radio.
Radio Removal:
1. Carefully pry out on the radio/heater control trim
bezel, unsnap to remove.
2. Extract two 3/8" bolts holding radio in, unplug and
remove radio.
NOTE: The rear of the aftermarket stereo should
be supported.
USE THESE
SUPPORT TABS
AS REQUIRED
REMOVE
ALIGNMENT
PIN - TOP
USE THESE
SUPPORT TABS
AS REQUIRED
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THIS
BRACKET
USE THESE SUPPORT
TABS AS REQUIRED
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
4
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
13
1991-93 Chrysler Town & Country
1991-93 Dodge Caravan
1991-93 Plymouth Voyager
Read pages 2-4 for kit assembly.
1993-97
1993-97
1993-97
Chrysler Concorde
Dodge Intrepid
Eagle Vision
Read pages 2-4 for kit assembly.
Radio Removal:
Radio Removal:
1. Pull the radio trim bezel out to release the snap clips,
and remove the bezel.
2. Extract the two bolts securing the radio, pull the radio
from the cavity, unplug all connectors and remove
the radio.
1. Remove the cigarette lighter.
2. Using a panel removal tool, carefully pry outward to release
the clips securing the dash bezel and remove the bezel.
3. Extract the two screws securing the rear hatch switch to the
dash bezel.
4. Extract the two 3/8" bolts securing the radio to the dash.
5. Pull the radio out of the dash, and unplug all the connectors.
Disconnect the ground strap and remove the radio.
USE THESE
SUPPORT TABS
AS REQUIRED
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
USE THESE
SUPPORT TABS
AS REQUIRED
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
1990
Chrysler Town & Country
1984-90 Dodge Caravan
1984-90 Plymouth Voyager
Read pages 2-4 for kit assembly.
1980-83
1980-83
Chrysler Cordoba
Dodge Mirada
Radio Removal:
Radio Removal:
1. Reach behind ashtray and unsnap the carrier housing to
remove the ashtray.
2. Remove three screws along the top edge of the radio trim
panel.
3. Remove two screws below the radio trim panel. Remove the
trim panel.
4. Remove two screws securing the radio to dash then pull the
radio out.
5. Disconnect the power, antenna, and all speaker and electrical
connections. Remove the radio.
1. Remove four screws securing the radio dash
panel: two above the radio and two above the
heater controls.
2. Remove the radio dash panel. Remove two
screws securing the radio to the dash. Pull the
radio out.
3. Disconnect power, antenna, and all speaker and
electrical connections.
USE THESE
SUPPORT TABS
AS REQUIRED
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
12
Read pages 2-4 for kit assembly.
USE THESE
SUPPORT TABS
AS REQUIRED
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
5
1975-79 Chrysler Cordoba
1975-77 Plymouth Fury
Read pages 2-4 for kit assembly.
1996-00 Chrysler Town & Country
1996-00 Dodge Caravan
1996-00 Plymouth Voyager
Read pages 2-4 for kit assembly.
Radio Removal:
Radio Removal:
1. Remove four securing screws from the bottom edge of the radio
dash panel.
2. Remove two securing screws from the top edge of the panel
above the radio.
3. Unscrew the retainer ring securing the remote mirror control
and remove the panel.
4. Remove two screws securing radio to the dash. Pull the radio
out.
5. Disconnect power, antenna and all speaker and electrical
connections.
USE THESE
SUPPORT TABS
AS REQUIRED
1. Extract two screws in the trim bezel from just
above the radio.
2. Pull the radio trim bezel away from the dash,
unplug the ac/heating control.
3. Extract the two screws securing the radio to the
dash, pull the radio from the cavity, disconnect
the ground strap, unplug all connectors and
remove the radio.
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT TABS
AS REQUIRED
R SPACER
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THIS
BRACKET
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
1990-93 Chrysler Fifth Avenue/Imperial
1988-93 Chrysler New Yorker
1988-93 Dodge Dynasty
Read pages 2-4 for kit assembly.
1. Remove five screws from along the top side of the
radio/instrument panel dash trim.
2. Lower the steering column, place the gear selector
in drive, then remove the trim panel.
3. Remove two bolts securing the radio, and pull the
radio out, disconnect wire harnesses, ground strap
and antenna lead, then remove the radio.
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
PRESS FIT ON ALIGNMENT 2 PLACES
USE THESE SUPPORT
TABS AS REQUIRED
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
1994-95 Chrysler Town & Country
1994-95 Dodge Caravan
1994-95 Plymouth Voyager
Read pages 2-4 for kit assembly.
Radio Removal:
Radio Removal:
USE THESE
SUPPORT TABS
AS REQUIRED
L SPACER
1. Using a panel removal tool carefully pry up on the dash panel at the
base of the windshield (speaker grille panel) to release the fastening
clips securing it to the dash and pull out on the panel to remove.
2. Pry up the piece of trim that looks like a vent in front of the instrument
light cluster on top of the dash us
ing a panel removal tool to
release and remove the trim.
3. Carefully pry out on the trim panel surrounding the heater controls using a panel removal
tool to release the fastening clips securing the trim to the dash and remove the trim.
4. Extract the three screws securing the bottom of the radio trim bezel to the dash.
5. Extract the three screws securing the front of the instrument light cluster to the top of the dash.
6. Extract the screw securing the back of the instrument light cluster to the dash, pry up on the
light cluster with a panel removal tool, unplug all connectors and remove.
7. Extract the three screws securing the top of the radio trim bezel to the dash on the drivers side of the dash.
8. Pull the radio trim bezel away from the dash, unplug all connectors, shift the gear select lever into Low, tilt
the steering wheel down and remove
the bezel.
USE THESE
9. Extract the two screwS securing the
SUPPORT TABS
AS REQUIRED
radio to the dash, pull the radio from
the cavity, disconnect the ground strap
unplug all connectors and remove the
REMOVE
ALIGNMENT
radio.
USE THIS
BRACKET
PIN - BOTTOM
USE THESE SUPPORT
TABS AS REQUIRED
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
6
11
1975-78 Chrysler Newport, New Yorker
1975-77 Dodge Royal Monaco
1975-79 Plymouth Gran Fury
Read pages 2-4 for kit assembly.
Radio Removal:
1. Remove three screws from the bottom edge of the dash panel.
2. Remove the ashtray and remove one screw retaining the dash
panel.
3. Disconnect the cigarette lighter and wiper wires.
4. Pull the dash panel out from the top. Place the gear
selector in low gear and remove the dash panel.
5. Release the radio rear support. Remove two screws
securing the radio to the dash. Pull the radio out.
6. Disconnect the power, antenna, and all speaker and electrical
connections.
USE THESE
SUPPORT TABS
AS REQUIRED
Chrysler Fifth Avenue
Chrysler Le Baron
Dodge Diplomat
Plymouth Gran Fury
Read pages 2-4 for kit assembly.
Radio Removal:
1. Remove four screws from the top edge of the
dash panel and four screws from the bottom
edge. Remove the panel.
2. Remove two screws securing the radio to the
dash and pull out.
3. Disconnect power, antenna, and all speaker,
and electrical connections.
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
1979-89
1977-81
1977-89
1984-89
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
USE THESE
SUPPORT TABS
AS REQUIRED
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
Read pages 2-4 for kit assembly.
1995-00 Chrysler Sebring
1995-00 Dodge Avenger
Read pages 2-4 for kit assembly.
1984-87 Chrysler New Yorker
Radio Removal:
Radio Removal:
1. Carefully pry out on radio/AC control trim bezel
to release the snap clips. Remove the bezel.
2. Extract the two screws holding radio in, unplug
connector, unbolt ground wire from rear of radio
and remove radio.
1. Remove nine securing screws from the top and
bottom of the radio trim panel. Remove the panel by
pulling it down and out.
2. Unhook the wiring harness.
3. Remove the two Chrysler anti-theft bolts retaining the
radio (use Snap-On bit TTW 12 for 1/4" drive) and
remove the radio. Disconnect power, ground cable,
antenna and speaker wires.
USE THIS
BRACKET
(TOP)
USE THESE
SUPPORT TABS
AS REQUIRED
USE THESE
SUPPORT TABS
AS REQUIRED
REMOVE
ALIGNMENT
PIN - TOP
USE THIS
BRACKET
USE THIS BRACKET
(BOTTOM)
USE THESE
SUPPORT TABS
AS REQUIRED
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
10
USE THESE SUPPORT
TABS AS REQUIRED
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
7
1981-83
1979-81
1979-83
1979-81
Read pages 2-4 for kit assembly.
Chrysler Imperial
Chrysler Newport
Chrysler New Yorker
Dodge St. Regis
1987-93 Chrysler Le Baron "Coupe"
Read pages 2-4 for kit assembly.
Radio Removal:
1. Remove two screws, one from each lower corner of the
radio/console trim panel.
2. Gently snap off the trim panel.
3. Remove two screws securing the right side panel of the
console, one at top, one at bottom; remove the side
panel.
4. Remove two screws from the radio mounting
bracket. Disconnect the wire harness, antenna
lead, and ground strap. Remove the radio.
Radio Removal:
1. Remove four screws securing the radio dash panel: two
above the radio and two above the heater controls.
2. Remove radio dash panel.
3. Remove two screws securing the radio to the dash. Pull
the radio out.
4. Disconnect power, antenna, and all speaker and electrical
connections.
USE THESE
SUPPORT TABS
AS REQUIRED
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
Read pages 2-4 for kit assembly.
1984-86 Chrysler Laser
Radio Removal:
1. Remove one screw from each side of the
ashtray.
2. Pull off the trim panel.
3. Remove two screws securing the radio to the
dash. Pull the radio out.
4. Disconnect the power, antenna, and all
speaker and electrical connections.
USE THESE
SUPPORT TABS
AS REQUIRED
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
Read pages 2-4 for kit assembly.
1994-97 Chrysler LHS
1994-96 Chrysler New Yorker
Radio Removal:
1. Remove the ashtray from the dash.
2. Carefully pry out on the perimeter radio dash bezel
using a panel removal tool to release the fastening
clips and remove the radio dash bezel.
3. Extract the two screws securing the radio to the
dash, pull the radio from the dash cavity, unplug all
connectors and remove the radio.
USE THESE
SUPPORT TABS
AS REQUIRED
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
8
USE THESE
SUPPORT TABS
AS REQUIRED
REMOVE
ALIGNMENT
PIN - BOTTOM
USE THESE
SUPPORT
TABS AS
REQUIRED
USE THIS
BRACKET
USE THE SHADED MOUNTING TABS AND THE INDICATED BRACKETS. CUT OFF THE REMAINING TABS AND DISCARD.
FOR DIN ISO AND SHAFT RADIO INSTALLATION, SEE PAGES 3 & 4.
9

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement