www.hatcocorp.com

Register Online!

(see page 2)

Convected Drawer Warmer

CDW-3N Series

Installation and Operating Manual

P/N 07.04.469.00

WARNING

Do not operate this equipment unless you have read and understood the contents of this manual! Failure to follow the instructions contained in this manual may result in serious injury or death. This manual contains important safety information concerning the maintenance, use, and operation of this product. If you’re unable to understand the contents of this manual, please bring it to the attention of your supervisor. Keep this manual in a safe location for future reference.

ADVERTENCIA

No opere este equipo al menos que haya leído y comprendido el contenido de este manual! Cualquier falla en el seguimiento de las instrucciones contenidas en este manual puede resultar en un serio lesión o muerte. Este manual contiene importante información sobre seguridad concerniente al mantenimiento, uso y operación de este producto. Si usted no puede entender el contenido de este manual por favor pregunte a su supervisor. Almacenar este manual en una localización segura para la referencia futura.

AVERTISSEMENT

Ne pas utiliser cet équipement sans avoir lu et compris le contenu de ce manuel !

Le non-respect des instructions contenues dans ce manuel peut entraîner de graves blessures ou la mort. Ce manuel contient des informations importantes concernant l'entretien, l'utilisation et le fonctionnement de ce produit. Si vous ne comprenez pas le contenu de ce manuel, veuillez le signaler

à votre supérieur. Conservez ce manuel dans un endroit sûr pour pouvoir vous y référer plus tard.

© 2012 Hatco Corporation

CONTENTS

Important Owner Information ..............................................2

Introduction...........................................................................2

Important Safety Information...............................................3

Model Description.................................................................4

Model Designation................................................................4

Specifications........................................................................4

Plug Configurations .........................................................4

Electrical Rating Chart.....................................................5

Dimensions......................................................................5

Installation.............................................................................5

General............................................................................5

Installing Casters .............................................................6

Operation...............................................................................6

General............................................................................6

Changing the Setpoint Temperature................................7

Locking/Unlocking the Digital Temperature

Controller ......................................................................7

Maintenance ..........................................................................7

General............................................................................7

Cleaning ..........................................................................7

Troubleshooting Guide ........................................................8

Options and Accessories.....................................................9

Limited Warranty.................................................................10

Authorized Parts Distributors............................Back Cover

IMPORTANT OWNER INFORMATION

Record the model number, serial number, voltage, and purchase date of the unit in the spaces below (specification label located on the back of the unit). Please have this information available when calling Hatco for service assistance.

model No. ________________________________________

Serial No. ________________________________________

Voltage __________________________________________

Date of Purchase __________________________________

Business 8:00 am to 5:00

Pm

Hours: Central Standard Time (C.S.T.)

(Summer Hours: June to September –

8:00 am to 5:00

Pm

C.S.T. monday through Thursday

8:00 am to 2:30

Pm

C.S.T. Friday)

Telephone: (800) 558-0607; (414) 671-6350

E-mail: [email protected]

Fax: (800) 690-2966 (Parts and Service)

(414) 671-3976 (International)

Register your unit!

Completing online warranty registration will prevent delay in obtaining warranty coverage. access the Hatco website at

www.hatcocorp.com, select the Parts & Service pull-down menu, and click on “Warranty Registration”.

24 Hour 7 Day Parts and Service

Assistance available in the United States and Canada by calling (800) 558-0607.

additional information can be found by visiting our web site at

www.hatcocorp.com.

INTRODUCTION

The Hatco Convected Drawer Warmer is designed to keep foods at optimum serving temperatures without affecting quality.

It is built for tough kitchen duty with rugged stainless steel construction, heavy-duty hardware, stainless steel slides, and positive-closing drawers. The Convected Drawer Warmer’s unique air-flow forces warm air throughout the unit, creating a blanket-effect of dry heat around the food product.

The Convected Drawer Warmer is a product of extensive research and field testing. The materials used were selected for maximum durability, attractive appearance, and optimum performance. Every unit is inspected and tested thoroughly prior to shipment.

This manual provides the installation, safety, and operating instructions for the Convected Drawer Warmer. Hatco recommends all installation, operating, and safety instructions appearing in this manual be read prior to installation or operation of the unit.

Safety information that appears in this manual is identified by the following signal word panels:

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE

NOTICE is used to address practices not related to personal injury.

2

Form No. CDWm-0412

IMPORTANT SAFETy INFORMATION

Read the following important safety information before using this equipment to avoid serious injury or death and to avoid damage to equipment or property

.

WARNING

ELECTRIC ShOCK hAzARD:

• Plug unit into a properly grounded electrical receptacle of the correct voltage, size, and plug configuration. If plug and receptacle do not match, contact a qualified electrician to determine and install proper voltage and size electrical receptacle.

• Turn OFF power switch, unplug power cord, and allow unit to cool before performing any cleaning, adjustments, or maintenance.

• Unit is not weatherproof. Locate unit indoors where the ambient air temperature is a minimum of 70°F (21°C).

• DO NOT submerge or saturate with water. Unit is not waterproof. Do not operate if unit has been submerged or saturated with water.

• Do not steam clean or use excessive water on the unit.

• This unit is not “jet-proof” construction. Do not use jetclean spray to clean this unit.

• Do not pull unit by power cord.

• Discontinue use if power cord is frayed or worn.

• Do not attempt to repair or replace a damaged power cord. The cord must be replaced by hatco, an

Authorized hatco Service Agent, or a person with similar qualifications.

• This unit must be serviced by qualified personnel only.

Service by unqualified personnel may lead to electric shock or burn.

• Use only Genuine hatco Replacement Parts when service is required. Failure to use Genuine hatco

Replacement Parts will void all warranties and may subject operators of the equipment to hazardous electrical voltage, resulting in electrical shock or burn.

Genuine hatco Replacement Parts are specified to operate safely in the environments in which they are used. Some aftermarket or generic replacement parts do not have the characteristics that will allow them to operate safely in hatco equipment.

FIRE hAzARD:

• Locate unit a minimum of 1″ (25 mm) from combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur.

• Do not use harsh chemicals such as bleach

(or cleaners containing bleach), oven cleaners, or flammable cleaning solutions to clean this unit.

WARNING

Make sure food product has been heated to the proper foodsafe temperature before placing in unit. Failure to heat food product properly may result in serious health risks. This unit is for holding preheated food product only.

Make sure all operators have been instructed on the safe and proper use of the unit.

This unit is not intended for use by children or persons with reduced physical, sensory, or mental capabilities.

Ensure proper supervision of children and keep them away from the unit.

This unit has no “user-serviceable” parts. If service is required on this unit, contact an Authorized hatco Service

Agent or contact the hatco Service Department at

800-558-0607 or 414-671-6350; fax 800-690-2966; or

International fax 414-671-3976.

CAUTION

BURN hAzARD:

• Some exterior surfaces on the unit will get hot. Use caution when touching these areas.

• Use caution when opening drawer. hot air escapes when drawer is open.

Locate unit in an area that is convenient for use. The location should be level and strong enough to support the weight of the unit and contents.

NOTICE

Do not lay unit on front or back side. Damage to unit could occur.

Use non-abrasive cleaners and cloths only. Abrasive cleaners and cloths could scratch finish of unit, marring its appearance and making it susceptible to soil accumulation.

Form No. CDWm-0412

3

MODEL DESCRIPTION

All Models

Hatco Convected Drawer Warmers are designed to keep foods hot, flavor-fresh, and crisp until served. They are nonhumidified, single cavity/single temperature controlled units that provide even, dry heat for food product that does not require humidity or moisture. Convected Drawer Warmers are constructed of rugged stainless steel with durable nylon rollers,

12-gauge stainless steel slides, and heavy-duty hardware. The insulated top and sides of the drawer warmers provide maximum energy efficiency.

NOTE: Refer to the

OPTIONS aND aCCESSORIES section

for additional available features.

Model CDW-3N

The CDW-3N model has three individual drawers that each hold a full-size food pan up to 6″ (152 mm) deep. It features a digital temperature controller and a POWER ON/OFF switch that control the temperature and power for the entire unit.

POWER ON/OFF Switch

Digital

Temperature

Controller model CDW-3N

MODEL DESIGNATION

Convected Drawer Warmer

Quantity of Drawers

C D W - X N

Narrow Width Unit

SPECIFICATIONS

Plug Configurations

Units are supplied from the factory with an electrical cord and plug installed. Plugs are supplied according to the applications.

WARNING

ELECTRIC ShOCK hAzARD: Plug unit into a properly grounded electrical receptacle of the correct voltage, size, and plug configuration. If plug and receptacle do not match, contact a qualified electrician to determine and install proper voltage and size electrical receptacle.

NOTE: Specification label located on the back of the unit. See label for serial number and verification of unit electrical information.

NEMA 5-15P

BS-1363

CEE 7/7 Schuko AS 3112

Plug Configurations

NOTE: Receptacle not supplied by Hatco.

4

Form No. CDWm-0412

SPECIFICATIONS

Electrical Rating Chart

Model

CDW-3N

Voltage

120

230

Dimensions

Model

CDW-3N

Width

(A)

16-5/8''

(420 mm)

Watts

1015

933

Depth

(B)

30-1/2''

(774 mm)

Amps

8.5

4.1

height

(C)

30''

(762 mm)

Plug Configuration

NEma 5-15P

CEE 7/7 Schuko, aS 3112, BS-1363

Shipping Weight

179 lbs. (81 kg)

179 lbs. (81 kg)

A

B

C

Front View Side View

CDW-3N Dimensions

General

The Convected Drawer Warmer is shipped with most components pre-assembled. Casters must be installed on location. Care should be taken when unpacking the shipping carton to avoid damage to unit and the components enclosed.

WARNING

ELECTRIC ShOCK hAzARD: Unit is not weatherproof.

Locate the unit indoors where the ambient air temperature is a minimum of 70°F (21°C).

FIRE hAzARD: Locate unit a minimum of 1″ (25 mm) from combustible walls and materials. If safe distances are not maintained, discoloration or combustion could occur.

NOTE: The unit must be transported in the upright position.

INSTALLATION

1. Remove the unit from the carton.

NOTE: To prevent delay in obtaining warranty coverage, complete online warranty registration. See the

ImPORTaNT OWNER INFORmaTION section for

details.

2. Remove tape and protective packaging from all surfaces of the unit

3. Install the casters onto the unit. Refer to the installation procedure in this section.

4. Place the unit in the desired location.

• Locate the unit in an area where the ambient air temperature is constant and a minimum of 70°F (21°C).

avoid areas that may be subject to active air movements or currents (i.e., near exhaust fans/hoods and air conditioning ducts).

• make sure the unit is located on solid, level flooring.

• make sure the unit is at the proper height in an area convenient for use.

Form No. CDWm-0412

5

INSTALLATION

Installing Casters

Use the following procedure to install casters onto the bottom of the unit.

NOTICE

Do not lay unit on the front or back side or damage to the unit could occur.

1. Remove any pans from the drawers of the unit.

2. Carefully lay the unit on its left or right side (requires two people).

3. align the four holes on the caster plate with the four holes in the unit mounting bracket at one corner of the unit

4. Install a bolt through each of the holes in the caster plate and into the unit mounting bracket. Tighten securely.

OPERATION

General

Use the following procedures to operate a Convected Drawer

Warmer.

WARNING

Read all safety messages in the IMPORTANT SAFETy

INFORMATION section before operating this equipment.

1. Plug the unit into an electrical receptacle of the correct voltage, size, and plug configuration. See the

SPECIFICaTIONS section for details.

2. move the POWER ON/OFF (I/O) switch to the ON (I) position. The switch will illuminate.

• The digital temperature controller will energize and the current temperature of the unit will appear on the display.

• The phrase “out 1” will appear in the upper left corner of the display to show that the unit is in heat mode.

CAUTION

BURN hAzARD:

• Some exterior surfaces on unit will get hot. Use caution when touching these areas.

• Use caution when opening drawer. hot air escapes when drawer is open.

Caster Plate

Bolt

Mounting

Bracket

Installing Casters

5. Repeat steps 3 and 4 for the remaining three casters.

6. Return the unit to the upright position (requires two people).

3. Press and release the key on the digital temperature controller to verify the setpoint temperature.

• The setpoint temperature will be shown for 15 seconds.

after 15 seconds, the display will revert to the current temperature of the unit. To change the setpoint temperature, refer to “Changing the Setpoint

Temperature” in this section.

“out 1”

Fahrenheit

Symbol

SET

Key

Down Arrow

Key

Up Arrow

Key

Digital Temperature Controller

NOTE: The digital temperature controller is pre-set to a setpoint temperature of 195°F (91°C) at the factory. Once the setpoint temperature is changed, the new setpoint temperature will remain in memory until it is changed again. The maximum setpoint temperature is 195°F

(91°C).

4. allow the unit 15–20 minutes to reach operating temperature before loading preheated food product.

Digital Temperature Controller

POWER ON/OFF (I/O) Switch

CDW-3N Control Panel

6

Form No. CDWm-0412

Changing the Setpoint Temperature

Use the following procedure to change the setpoint temperature of the unit.

1. Press and release the key. The current setpoint temperature will be shown on the display and ”out 1” will flash in the upper left corner.

2. Press the key or key within 15 seconds to change the setpoint temperature. If no key is pressed within 15 seconds, the display will revert to the current temperature of the unit.

3. Press the key or wait 15 seconds to lock in the new setpoint temperature.

OPERATION

Locking/Unlocking the Digital Temperature

Controller

The keys on the digital temperature controller can be locked to prevent unauthorized changes to the settings.

To lock the keys of the digital temperature controller:

• Press and hold both the key and key at the same time for over two seconds. The message “Loc” will appear on the display.

To unlock the keys of the digital temperature controller:

• Press and hold both the key and key at the same time until the message “UnL” appears on the display.

General

The Hatco Convected Drawer Warmer is designed for maximum durability and performance with minimum maintenance.

WARNING

ELECTRIC ShOCK hAzARD:

• Turn OFF power switch, unplug power cord, and allow unit to cool before performing any cleaning, adjustments, or maintenance.

• DO NOT submerge or saturate with water. Unit is not waterproof. Do not operate if unit has been submerged or saturated with water.

• Do not steam clean or use excessive water on the unit.

• This unit is not “jet-proof” construction. Do not use jetclean spray to clean this unit.

This unit must be serviced by qualified personnel only.

Service by unqualified personnel may lead to electric shock or burn.

This unit has no “user-serviceable” parts. If service is required on this unit, contact an Authorized hatco Service

Agent or contact the hatco Service Department at

800-558-0607 or 414-671-6350; fax 800-690-2966; or

International fax 414-671-3976.

MAINTENANCE

Cleaning

To preserve the finish of the unit as well as maintain performance, it is recommended that the unit be cleaned daily.

1. Turn off the unit, unplug the power cord, and allow the unit to cool.

2. Remove and wash all food pans.

3. Wipe down all stainless steel surfaces using a damp cloth.

Stubborn stains may be removed with a good non-abrasive cleaner. Hard to reach areas should be cleaned with a small brush and mild soap.

NOTICE

Use non-abrasive cleaners and cloths only. Abrasive cleaners and cloths could scratch finish of unit, marring its appearance and making it susceptible to soil accumulation.

4. Wipe dry the entire unit using a dry, non-abrasive cloth.

Form No. CDWm-0412

7

TROUBLEShOOTING GUIDE

WARNING

This unit must be serviced by qualified personnel only.

Service by unqualified personnel may lead to electric shock or burn.

WARNING

ELECTRIC ShOCK hAzARD: Turn OFF power switch, unplug power cord, and allow unit to cool before performing any cleaning, adjustments, or maintenance.

Symptom

Unit too hot.

Unit not hot enough.

Unit not working at all.

Probable Cause

Setpoint temperature too high.

Corrective Action

Change the setpoint temperature to a lower setting.

Unit connected to incorrect power supply.

Verify with qualified personnel that power supply matches unit specification.

Digital temperature controller is defective.

Contact an authorized Hatco Service agent or

Hatco for assistance.

Unit not allowed enough time to preheat.

allow unit 15–20 minutes to reach operating temperature.

Setpoint temperature too low.

Drawer(s) not closed completely.

Change the setpoint temperature to a higher setting.

make sure all drawers are closed completely.

Digital temperature controller is defective.

Contact an authorized Hatco Service agent or

Hatco for assistance.

Unit not plugged in.

Plug unit into proper power supply.

Unit not turned on.

Circuit breaker tripped.

POWER ON/OFF (I/O) switch defective.

move POWER ON/OFF (I/O) switch to the ON position.

Reset circuit breaker.

Contact an authorized Hatco Service agent or

Hatco for assistance.

Digital temperature controller is defective.

Contact an authorized Hatco Service agent or

Hatco for assistance.

Heating element burned out.

Contact an authorized Hatco Service agent or

Hatco for assistance.

8

Form No. CDWm-0412

Food Pans

accessory stainless steel food pans are available in various sizes.

ST PAN 2................Full size stainless steel pan at 2-1/2″

(64 mm) deep — 12-3/4″W x 20-3/4″D x

2-1/2″H (324 x 527 x 64 mm)

ST PAN 4................Full size stainless steel pan at 4″ (102 mm) deep — 12-3/4″W x 20-3/4″D x 4″H

(324 x 527 x 102 mm)

hDW 6″ PAN..........Full size stainless steel pan at 6″ (152 mm) deep — 12-3/4″W x 20-3/4″D x 6″H

(324 x 527 x 152 mm)

OPTIONS AND ACCESSORIES

Trivets

accessory stainless steel or nickel-plated trivets are available in various sizes.

TRIVET (1/2)SS ....Half-size stainless steel trivet —

10-3/16″W x 7-5/8″D (259 x 194 mm)

TRIVET SS ............Full size stainless steel trivet —

10-1/8″W x 18″D (257 x 457 mm)

TRIVET (1/2) ..........Half-size nickel-plated trivet —

10-3/16″W x 7-5/8″D (259 x 194 mm)

TRIVET ..................Full size nickel-plated trivet —

10-1/8″W x 18″D (257 x 457 mm)

Full Pan, 2-1/2″ Deep Full Pan, 4″ Deep

Full Trivet

Full Pan, 6″ Deep

Stainless Steel Food Pans

1/2 Trivet

Trivets

Form No. CDWm-0412

9

LIMITED WARRANTy

1. PRODUCT WARRANTy

Hatco warrants the products that it manufactures (the

“Products”) to be free from defects in materials and workmanship, under normal use and service, for a period of one (1) year from the date of purchase when installed and maintained in accordance with Hatco’s written instructions or

18 months from the date of shipment from Hatco. Buyer must establish the Product’s purchase date by registering the Product with Hatco or by other means satisfactory to Hatco in its sole discretion.

Hatco warrants the following Product components to be free from defects in materials and workmanship from the date of purchase (subject to the foregoing conditions) for the period(s) of time and on the conditions listed below:

a) One (1) year Parts and Labor PLUS One (1)

Additional year Parts-Only Warranty:

Conveyor Toaster Elements (metal sheathed)

Drawer Warmer Elements (metal sheathed)

Drawer Warmer Drawer Rollers and Slides

Strip Heater Elements (metal sheathed)

Display Warmer Elements (metal sheathed air heating)

Holding Cabinet Elements (metal sheathed air heating)

Heated Well Elements — HWB Series (metal sheathed)

b) One (1) year Parts and Labor PLUS Four (4) years

Parts-Only Warranty on pro-rated terms that hatco will explain at Buyer’s request:

3CS and FR Tanks

c) One (1) year Parts and Labor PLUS Nine (9) years

Parts-Only Warranty on:

Electric Booster Heater Tanks

Gas Booster Heater Tanks

d) Ninety (90) Day Parts-Only Warranty:

Replacement Parts

THE FOREGOING WaRRaNTIES aRE EXCLUSIVE aND IN

LIEU OF aNY OTHER WaRRaNTY, EXPRESSED OR

ImPLIED, INCLUDING BUT NOT LImITED TO aNY ImPLIED

WaRRaNTY OF mERCHaNTaBILITY OR FITNESS FOR a

PaRTICULaR PURPOSE OR PaTENT OR OTHER

INTELLECTUaL PROPERTY RIGHT INFRINGEmENT.

Without limiting the generality of the foregoing, SUCH

WaRRaNTIES DO NOT COVER: Coated incandescent light bulbs, fluorescent lights, heat lamp bulbs, coated halogen light bulbs, halogen heat lamp bulbs, xenon light bulbs, LED light tubes, glass components, and fuses; Product failure in booster tank, fin tube heat exchanger, or other water heating equipment caused by liming, sediment buildup, chemical attack, or freezing; or Product misuse, tampering or misapplication, improper installation, or application of improper voltage.

2. LIMITATION OF REMEDIES AND DAMAGES

Hatco’s liability and Buyer’s exclusive remedy hereunder will be limited solely, at Hatco’s option, to repair or replacement using new or refurbished parts or Product by Hatco or a Hatcoauthorized service agency (other than where Buyer is located outside of the United States, Canada, United Kingdom, or australia, in which case Hatco’s liability and Buyer’s exclusive remedy hereunder will be limited solely to replacement of part under warranty) with respect to any claim made within the applicable warranty period referred to above. Hatco reserves the right to accept or reject any such claim in whole or in part.

In the context of this Limited Warranty, “refurbished” means a part or Product that has been returned to its original specifications by Hatco or a Hatco-authorized service agency.

Hatco will not accept the return of any Product without prior written approval from Hatco, and all such approved returns shall be made at Buyer’s sole expense. HaTCO WILL NOT BE

LIaBLE, UNDER aNY CIRCUmSTaNCES, FOR

CONSEQUENTIaL OR INCIDENTaL DamaGES, INCLUDING

BUT NOT LImITED TO LaBOR COSTS OR LOST PROFITS

RESULTING FROm THE USE OF OR INaBILITY TO USE THE

PRODUCTS OR FROm THE PRODUCTS BEING

INCORPORaTED IN OR BECOmING a COmPONENT OF aNY OTHER PRODUCT OR GOODS.

10

Form No. CDWm-0412

Form No. CDWm-0412

11

NOTES

hATCO AUThORIzED PARTS DISTRIBUTORS

ALABAMA

Birmingham 205-251-0159

ARIzONA

Service Solutions Group

Phoenix 602-234-2443

Byassee Equipment Co.

602-252-0402

CALIFORNIA

Industrial Electric

Chapman appl. Service

San Diego 619-298-7106

Commercial Parts & Service, Inc.

S. San Francisco 650-635-1900

COLORADO

Hawkins Commercial appliance

Englewood 303-781-5548

FLORIDA

Jacksonville 904-725-7800

3Wire Nass Service Co., Inc.

Orlando 407-425-2681

954-971-0456

Comm. appliance Service

Tampa 813-663-0313

GEORGIA

mableton 770-438-9797

Heritage Service Group

Norcross 866-388-9837

Southeastern Rest. Svc.

770-446-6177

hAWAII

Honolulu 808-848-1466

Food Equip Parts & Service

Honolulu 808-847-4871

ILLINOIS

Lombard 708-865-7278

Eichenauer Elec. Service

Decatur 217-429-4229

Cone’s Repair Service moline

INDIANA

Indianapolis

309-797-5323

317-545-9655

IOWA

Davenport 319-323-1823

Goodwin Tucker Group

Des moines 515-262-9308

KENTUCKy

Lexington 859-254-8854

Service Solutions Group

Louisville 502-451-5411

LOUISIANA

Baton Rouge 225-272-6620

MARyLAND

Baltimore

GCS Service

Silver Spring

MASSAChUSETTS

ace Service Co., Inc.

Needham

410-467-8080

301-585-7550

781-449-4220

MIChIGAN

Detroit 248-478-3320

Commercial Kitchen Service

Bay City 517-893-4561

MINNESOTA

GCS Service

Plymouth

MISSOURI

General Parts

Kansas City

Kaemmerlen Parts & Service

St. Louis 314-535-2222

NEBRASKA

Omaha 402-341-1414

NEVADA

Burney’s Commercial

Las Vegas 702-736-0006

NEW JERSEy

Jay Hill Repair

Fairfield

Service Plus

Flanders

800-345-4221

816-421-5400

973-575-9145

973-691-6300

NEW yORK

Brooklyn alpro Service Co.

Brooklyn

718-456-6544

718-386-2515

716-884-7425

Duffy’s Equipment Services, Inc.

Buffalo 800-836-1014

800-634-5005

Duffy’s Equipment Services, Inc.

Sauquoit 800-836-1014

315-422-9271

NORTh CAROLINA

authorized appliance

Charlotte 704-377-4501

OhIO

akron 330-753-6635

Service Solutions Group

513-772-6600

Commercial Parts and Service

Columbus 614-221-0057

E. a. Wichman Co.

Toledo

OKLAhOMA

Oklahoma City

Krueger, Inc.

Oklahoma City

419-385-9121

405-235-2184

405-528-8883

OREGON

Portland 503-624-0890

PENNSyLVANIA

Elmer Schultz Services

Philadelphia 215-627-5401

K & D Service Co.

Harrisburg

RhODE ISLAND

marshall Electric Co.

Providence

SOUTh CAROLINA

W. Columbia

TENNESSEE

Camp Electric memphis

717-236-9039

610-376-5444

401-331-1163

803-791-4420

901-527-7543

TEXAS

Fort Worth 800-433-1804 armstrong Repair Service

Houston 713-666-7100

Refrigerated Specialist, Inc.

mesquite 888-866-9276

UTAh

La monica’s Rest. Equip. Service murray 801-263-3221

VIRGINIA

Norfolk

Daubers

Springfield

757-855-4097

703-866-3600

WAShINGTON

3Wire Restaurant appliance

Seattle 800-207-3146

WISCONSIN

madison a.S.C., Inc.

milwaukee

608-246-3160

414-543-6460

CANADA

ALBERTA

Edmonton 780-438-1690

BRITISh COLUMBIA

Key Food Equipment Service

Vancouver 604-433-4484

MANITOBA

air Rite, Inc.

Winnipeg

NEW BRUNSWICK

moncton

ONTARIO

Toronto

Choquette - CKS, Inc.

Ottawa

QUÉBEC

montreal

Choquette - CKS, Inc.

Québec City

204-895-2300

506-855-4228

416-422-5580

613-739-8458

514-722-2000

418-681-3944

UNITED KINGDOM

marren Group

Northants +44(0)1933 666233

HATCO CORPORATION

P.O. Box 340500

Milwaukee, WI 53234-0500 U.S.A.

(800) 558-0607 (414) 671-6350

Parts and Service Fax (800) 690-2966

International Fax (414) 671-3976 [email protected]

www.hatcocorp.com

Printed in U.S.a. april 2012

Register online!

See ImPORTaNT OWNER INFORmaTION for more information.

Part No. 07.04.469.00 Form No. CDWm-0412