ANZZI L-AZ007 lavatory faucet Installation guide
Below you will find brief information for lavatory faucet L-AZ007. This faucet is designed for use in a bathroom and has a wide spread design. It features two handles which allow for independent control of the hot and cold water flow. The faucet also includes a pop-up drain stopper which can be used to close off the drain. To use this faucet, you can easily control the water flow and temperature by using the two handles. The pop-up drain stopper can be used to stop and release water from the basin. Install and use it with caution, read through all of the instructions to avoid potential damage.
advertisement
1
2
3
4
5
20
10
13
14
15
6
7
8
9
11
12
16
17
18
19
L-AZ007
Installation Guide
For more information visit www.ANZZI.com or call 1-844-44-ANZZI
RECOMMENDED TOOLS
11
12
13
9
10
7
8
5
6
3
4
NO.
1
2
18
19
20
14
15
16
17
PART NAME
Handle assembly
Adapter
Lock nut
O-ring
Water valve assembly
Gasket assembly
Lock nut
Screw
Clamp spring
Spout
Washer
Aerator
O-ring
Gasket assembly
Lock nut
Flexible hose
Plastic lock ring
Aerator wrench
Allen key
Diverter cover
WIDE SPREAD LAVATORY FAUCET
ASME A112.18.1/CSA B125.1
The tools m ight b e applied t o t he following p laces:
Silicone Screw Knife Channel Locks Goggles screwdriver Adjustable Wrench Teflon tape Allen key
WARNING:
Please keep the tool for future use!
Attention: for easy installation, you will need:
1.To read all the installation instruction completely before
beginning.
2.To read all the warning, attention and maitenance
information.
3.To purchase the proper supply lines.
Step 1 Faucet and pop-up installation
Faucet installation
1 2 3 4
4.Insert lift rod through hole on faucet body. Connect extend rod to lift rod. Attach horizontal rod to extend rod using
fittings, tighten screw.
HOT
1/2”( 13mm) IPS
COLD
WARNING:
DON'T OVERTIGHTEN!
Step 2 Checking and testing
1 2
1.Position the body with o-ring in the installation surface as shown and secure it with gasket assembly and tighten
the lock nut with adjustable wrench.
2.Position the handle in installation surface as shown and secure it with fixing kit and tighten the screw with
screwdriver. Repeat the above steps for the other handle.
Caution: please be caution with the position of hot and cold handles.
3.Position the flexible hose as shown and fix it to the faucet as shown with clamp spring .
4.Connect the water supply lines to faucet and water supply valve and tighten it with wrench.
Warning: The water supply valve mentioned above are not included, please purchase them from plumbshop.
Pop-up installation
1 flange top rubber washer drain body sink base
2 flange washer locknut bottom rubber washer
3 align hole in drain stopper with guide rod opening
(pointed toward back wall) drain stopper o-ring sink drain body drain body drain stopper hole tailpiece horizontal rod rod ball plastic gasket rod guide nut
4 lift rod faucet body screw fittings extend rod horizontal rod
1.Remove pop-up drain stopper, and flange with top rubber washer for pop-up assembly. Insert drain body from
underneath of sink drain hole. Replace flange and top rubber washer back to drain body. Tighten flange as far as
possible. Remove and put silicone along bottom of. (Optional) Slide bottom rubber washer on drain body up against
bottom of sink. Tighten washer and locknut firmly against base for tight seal. Remove tailpiece from drain body, add
Teflon tape, replace tailpiece.
2.Replace pop-up drain stopper to drain body with o-ring in place, and align stopper hole with guide rod opening.
3.Remove rod guide nut and rod ball plastic gasket. Insert horizontal rod into drain body and through hole in drain
stopper. Replace rod guide nut with rod ball plastic gasket and tighten it.
1.
Remove the aerator by aerator wrench. Turn the faucet handle all the way on, turn on hot and cold water supply
and flush water lines for one minute. Reinstall aerator by aerator wrench.
2.Check all connections at arrows for leaks, re-tighten it if necessary.
BUT DON'T OVERTIGHTEN
Step 3 Cleaning and care
Daily cleaning and care are required in order to keep the product shining and properly working.
1 Clean it with water and dry it with soft cloth.
2 Clean the product with gentle liquid or glass cleaner.
3 Don't use acid cleaner.
4 Don't clean with abrasive material, abrasive paper or knife.
advertisement
Key Features
- Wide spread design
- Two handles for independent control
- Pop-up drain stopper
- Easy to control water flow and temperature
Frequently Answers and Questions
What tools are needed to install the faucet?
Where can I purchase the water supply lines?
How do I clean and care for the faucet?
Related manuals
advertisement