VIVOTEK FD8133 surveillance camera Specification

Add to my manuals
146 Pages

advertisement

VIVOTEK FD8133 surveillance camera Specification | Manualzz
VIVOTEK
Table of Contents
Overview������������������������������������������������������������������������������������������������������������������������������������������������������3
Read Before Use�������������������������������������������������������������������������������������������������������������������������������������3
Package Contents�����������������������������������������������������������������������������������������������������������������������������������3
Physical Description��������������������������������������������������������������������������������������������������������������������������������4
Installation����������������������������������������������������������������������������������������������������������������������������������������������������5
Hardware Installation�������������������������������������������������������������������������������������������������������������������������������5
Network Deployment�������������������������������������������������������������������������������������������������������������������������������7
Software Installation������������������������������������������������������������������������������������������������������������������������������10
Ready to Use����������������������������������������������������������������������������������������������������������������������������������������� 11
Adjusting the Lens��������������������������������������������������������������������������������������������������������������������������������� 11
Completion��������������������������������������������������������������������������������������������������������������������������������������������12
Accessing the Network Camera�����������������������������������������������������������������������������������������������������������������13
Using Web Browsers�����������������������������������������������������������������������������������������������������������������������������13
Using RTSP Players������������������������������������������������������������������������������������������������������������������������������15
Using 3GPP-compatible Mobile Devices�����������������������������������������������������������������������������������������������16
Using VIVOTEK Recording Software����������������������������������������������������������������������������������������������������17
Main Page��������������������������������������������������������������������������������������������������������������������������������������������������18
Client Settings��������������������������������������������������������������������������������������������������������������������������������������������21
Configuration����������������������������������������������������������������������������������������������������������������������������������������������23
System��������������������������������������������������������������������������������������������������������������������������������������������������24
Security�������������������������������������������������������������������������������������������������������������������������������������������������26
HTTPS���������������������������������������������������������������������������������������������������������������������������������������������������27
SNMP����������������������������������������������������������������������������������������������������������������������������������������������������32
Network�������������������������������������������������������������������������������������������������������������������������������������������������33
DDNS����������������������������������������������������������������������������������������������������������������������������������������������������47
Access List��������������������������������������������������������������������������������������������������������������������������������������������49
Video�����������������������������������������������������������������������������������������������������������������������������������������������������52
Motion Detection�����������������������������������������������������������������������������������������������������������������������������������62
Camera Tampering Detection ���������������������������������������������������������������������������������������������������������������65
Homepage Layout���������������������������������������������������������������������������������������������������������������������������������66
Application���������������������������������������������������������������������������������������������������������������������������������������������69
Recording����������������������������������������������������������������������������������������������������������������������������������������������82
Local Storage����������������������������������������������������������������������������������������������������������������������������������������86
System Log�������������������������������������������������������������������������������������������������������������������������������������������90
View Parameters�����������������������������������������������������������������������������������������������������������������������������������91
Maintenance������������������������������������������������������������������������������������������������������������������������������������������92
Appendix ���������������������������������������������������������������������������������������������������������������������������������������������������96
URL Commands for the Network Camera���������������������������������������������������������������������������������������������96
Technical Specifications����������������������������������������������������������������������������������������������������������������������144
Technology License Notice������������������������������������������������������������������������������������������������������������������145
Electromagnetic Compatibility (EMC)��������������������������������������������������������������������������������������������������146
2 - User's Manual
VIVOTEK
Overview
Read Before Use
The use of surveillance devices may be prohibited by law in your country. The Network Camera is not
only a high-performance web-ready camera but can also be part of a flexible surveillance system. It is
the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for
its intended use.
It is important to first verify that all contents received are complete according to the Package Contents
listed below. Take note of the warnings in the Quick Installation Guide before the Network Camera is
installed; then carefully read and follow the instructions in the Installation chapter to avoid damage due to
faulty assembly and installation. This also ensures the product is used properly as intended.
The Network Camera is a network device and its use should be straightforward for those who have basic
networking knowledge. It is designed for various applications including video sharing, general security/
surveillance, etc. The Configuration chapter suggests ways to best utilize the Network Camera and
ensure proper operations. For creative and professional developers, the URL Commands of the Network
Camera section serves as a helpful reference to customizing existing homepages or integrating with the
current web server.
Package Contents
■ FD8133 or FD8134
■ Power Adapter
■ Software CD
■ Alignment Sticker
■ Quick Installation Guide / Warranty Card
■ RJ45 Female/Female Coupler / Screws / Clamp Core
User's Manual - 3
VIVOTEK
Physical Description
Black Cover
Light Sensor
IR LEDs (8 units, distance 10m)
(FD8134 only)
Lens
MicroSD/SDHC
Card Slot
General I/O Terminal Block
Ethernet 10/100
RJ45 Plug
Reset Button
Status LED
Power Cord Socket
General I/O Terminal Block
This Network Camera provides a general I/O terminal block which is used to connect external
input / output devices. The pin definitions are described below.
Pin
+
-
Name
Digital Iutput +
Digital Iutput -
MicroSD/SDHC Card Capacity
This network camera is compliant with MicroSD/SDHC 32GB and other preceding standard SD
cards.
Hardware Reset
The reset button is used to reset the system or restore the factory default settings. Sometimes
resetting the system can return the camera to normal operation. If the system problems remain
after reset, restore the factory settings and install again.
Reset: Press and release the recessed reset button with a paper clip or thin object. Wait for the
Network Camera to reboot.
Restore: Press and hold the recessed reset button until the status LED rapidly blinks. Note that
all settings will be restored to factory default. Upon successful restore, the status LED will blink
green and red during normal operation.
4 - User's Manual
VIVOTEK
Installation
Hardware Installation
First, follow the instructions below to remove the dome cover.
Dome Cover
Network Camera
Record the MAC address before
installing the camera.
Model No: FD8134
MAC:0002D107258A
V I
RoHS
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Pat. 6,930,709
Made in Taiwan
Then remove the black cocer as shown below.
Tilt Adjustment Screw
User's Manual - 5
VIVOTEK
With idiot-proof mechanism design and very compact size, this Network Camera is very easy for
user to install in diverse indoor environment.
1.Attach the alignment sticker to the ceilling/wall.
2.Through the two circles on the sticker, drill two pilot holes into the ceilling/wall.
3. The Network Camera can be mounted with the cable routed through the ceiling/wall or from
the side. If you want to feed the cable through the ceiling/wall, drill a cable hole A as shown in
the above picture.
4.Hammer the supplied plastic anchors into the holes.
5.Align the two holes on each side of the camera base with the two plastic anchors on the ceilling/wall, insert the supplied screws to corresponding holes and secure them with a screwdriver.
A
Ceiling Mount
A
Wall Mount
6. Buckle the supplied clamp core onto the cable to against the EMI radiation.
The clamp core should be away
from the device at least 5 cm.
5 cm
6 - User's Manual
VIVOTEK
Network Deployment
Setting up the Network Camera over the Internet
This section explains how to configure the Network Camera to an Internet connection.
1. If you have external devices such as sensors and alarms, make the connection from the
general I/O terminal block.
+ : Digital input
- : Digital input
2. Use the supplied RJ45 female/female coupler to connect the Network Camera to a switch.
Use a Category 5 Cross Cable when Network Camera is directly connected to PC.
3. Connect the power cable from the Network Camera to a power outlet.
Ethernet Switch
POWER
COLLISION
1
2
3
4
5
LINK
RECEIVE
PARTITION
2
1
3
There are several ways to set up the Network Camera over the Internet. The first way is to set
up the Network Camera behind a router. The second way is to utilize a static IP. The third way is
to use PPPoE.
Internet connection via a router
Before setting up the Network Camera over the Internet, make sure you have a router and follow
the steps below.
1. Connect your Network Camera behind a router, the Internet environment is illustrated below.
Regarding how to obtain your IP address, please refer to Software Installation on page 11 for
details.
User's Manual - 7
VIVOTEK
WAN (Wide Area Network )
Internet
Router IP address : from ISP
POWER
COLLISION
1
2
3
4
5
IP address : 192.168.0.3
Subnet mask : 255.255.255.0
Default router : 192.168.0.1
LINK
RECEIVE
PARTITION
LAN (Local Area Network)
Router IP address : 192.168.0.1
Cable or DSL Modem
IP address : 192.168.0.2
Subnet mask : 255.255.255.0
Default router : 192.168.0.1
2. In this case, if the Local Area Network (LAN) IP address of your Network Camera is
192.168.0.3, please forward the following ports for the Network Camera on the router.
■ HTTP port
■ RTSP port
■ RTP port for video
■ RTCP port for video
If you have changed the port numbers on the Network page, please open the ports accordingly
on your router. For information on how to forward ports on the router, please refer to your
router’s user’s manual.
3. Find out the public IP address of your router provided by your ISP (Internet Service Provider).
Use the public IP and the secondary HTTP port to access the Network Camera from the
Internet. Please refer to Network Type on page 33 for details.
Internet connection with static IP
Choose this connection type if you are required to use a static IP for the Network Camera.
Please refer to LAN on page 33 for details.
Internet connection via PPPoE (Point-to-Point over Ethernet)
Choose this connection type if you are connected to the Internet via a DSL Line. Please refer to
PPPoE on page 34 for details.
8 - User's Manual
VIVOTEK
Set up the Network Camera through Power over Ethernet (PoE) (FD8134 only)
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data via a single
Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled
switch via Ethernet cable.
power + data transmission
POWER
COLLISION
1
2
3
4
LINK
RECEIVE
PARTITION
5
PoE Switch
When using a non-PoE switch
If your switch/router does not support PoE, use a PoE power injector (optional) to connect
between the Network Camera and a non-PoE switch.
PoE Power Injector
(optional)
POWER
COLLISION
1
2
3
4
5
LINK
RECEIVE
PARTITION
Non-PoE Switch
User's Manual - 9
VIVOTEK
Software Installation
Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up
your Network Camera on the LAN.
1. Install IW2 under the Software Utility directory from the software CD.
Double click the IW2 shortcut on your desktop to launch the program.
2. The program will conduct an analysis of your network environment.
After your network environment is analyzed, please click Next to continue the program.
3. The program will search for all VIVOTEK network devices on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC and model name
which matches the product label on your device to connect to the Network Camera via
Internet Explorer.
Network Camera
Model No: FD8134
MAC:0002D107258A
V I
RoHS
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Pat. 6,930,709
10 - User's Manual
Made in Taiwan
00-02-D1-73-02-02
0002D1730202
192.168.5.151
FD8134
VIVOTEK
Ready to Use
1. Access the Network Camera on the LAN.
2. Retrieve live video through a web browser or recording software.
Adjusting the Lens
Based on the live image retrieved from the camera, adjust the camera lens to the desired
viewing angle:
1.Turn the lens module left and right.
2. Loosen the tilt adjustment screws on both sides of the camera and then turn the lens module
up and down. Upon completion, tighten the screws.
Rotate the screw
3. Turn the lens to adjust the image orientation.
Turn the lens
Pan 350°
1
Tighten
Loosen
2
Tilt 85°
3
Rotate 350°
User's Manual - 11
VIVOTEK
3-axis Mechanism Design
The sophisticated 3-axis mechanism design offers very flexible, easy hardware installation for
either ceiling or wall mount.
Pan 350°
Tilt Adjustment Screw
Rotate 350°
Tilt 85°
DO NOT over rotate the lens.
Doing so will damage the
camera lens module.
Completion
1.Align the inner side of the black cover with the notch on both sides of the lens, fix the black
cover.
2.If you choose to the feed the cable through the ceiling/wall, arrange the cable neatly through
the cable hole. If you choose to feed the cable from the side, remove plate B.
3.Attach the dome cover to the camera as the direction shown below. With idiot-proof
mechanism design, the dome cover cannot be attatched if the angle does not fit. You will hear
a crisp sound when the dome cover is assembled successfully.
4.Finally, make sure all parts of the camera are securely installed.
2
1
Be aware of the cable route!
B
12 - User's Manual
3
VIVOTEK
Accessing the Network Camera
This chapter explains how to access the Network Camera through web browsers, RTSP players,
3GPP-compatible mobile devices, and VIVOTEK recording software.
Using Web Browsers
Use Installation Wizard 2 (IW2) to access to the Network Cameras on the LAN.
If your network environment is not a LAN, follow these steps to access the Network Camera:
1. Launch your web browser (ex. Microsoft® Internet Explorer, Mozilla Firefox, or Netscape).
2. Enter the IP address of the Network Camera in the address field. Press Enter.
3. The live video will be displayed in your web browser.
4. If it is the first time installing the VIVOTEK network camera, an information bar will pop up as
shown below. Follow the instructions to install the required plug-in on your computer.
NOTE
► For Mozilla Firefox or Netscape users, your browser will use Quick Time to stream the live
video. If you do not have Quick Time on your computer, please download it first, then launch
the web browser.
User's Manual - 13
VIVOTEK
► By default, the Network Camera is not password-protected. To prevent unauthorized access,
it is highly recommended to set a password for the Network Camera.
For more information about how to enable password protection, please refer to Security on
page 26.
► If you see a dialog box indicating that your security settings prohibit running ActiveX ®
Controls, please enable the ActiveX ® Controls for your browser.
1. Choose Tools > Internet Options > Security > Custom Level.
2. Look for Download signed ActiveX ® controls; select Enable or Prompt. Click OK.
3. Refresh your web browser, then install the Active X ® control. Follow the instructions to
complete installation.
14 - User's Manual
VIVOTEK
Using RTSP Players
To view the MPEG-4 streaming media using RTSP players, you can use one of the following
players that support RTSP streaming.
Quick Time Player
Real Player
VLC media player
1. Launch the RTSP player.
mpegable
Player
2. Choose
File > Open
URL. A URL dialog box will pop up.
3. The address format is rtsp://<ip address>:<rtsp port>/<RTSP streaming access name for
pvPlayer
stream1 or stream2>
As most ISPs and players only allow RTSP streaming through port number 554, please set the
RTSP port to 554. For more information, please refer to RTSP Streaming on page 45.
For example:
rtsp://192.168.5.151:554/live.sdp
4. The live video will be displayed in your player.
For more information on how to configure the RTSP access name, please refer to RTSP
Streaming on page 45 for details.
Video 16:38:01 2010/03/23
User's Manual - 15
VIVOTEK
Using 3GPP-compatible Mobile Devices
To view the streaming media through 3GPP-compatible mobile devices, make sure the Network
Camera can be accessed over the Internet. For more information on how to set up the Network
Camera over the Internet, please refer to Setup the Network Camera over the Internet on page 7.
To utilize this feature, please check the following settings on your Network Camera:
1. Because most players on 3GPP mobile phones do not support RTSP authentication, make
sure the authentication mode of RTSP streaming is set to disable.
For more information, please refer to RTSP Streaming on page 45.
2. As the the bandwidth on 3G networks is limited, you will not be able to use a large video size.
Please set the video streaming parameters as listed below.
For more information, please refer to Viewing Window on page 57.
Video Mode
Frame size
Maximum frame rate
Intra frame period
Video quality (Constant bit rate)
MPEG-4
176 x 144
5 fps
1S
40kbps
3. As most ISPs and players only allow RTSP streaming through port number 554, please set
the RTSP port to 554. For more information, please refer to RTSP Streaming on page 45.
4. Launch the player on the 3GPP-compatible mobile devices (ex. Real Player).
5. Type the following URL commands into the player.
The address format is rtsp://<public ip address of your camera>:<rtsp port>/<RTSP streaming
access name for stream 3>.
For example:
rtsp://192.168.5.151:554/live.sdp
16 - User's Manual
VIVOTEK
Using VIVOTEK Recording Software
The product software CD also contains recording software, allowing simultaneous monitoring
and video recording for multiple Network Cameras. Please install the recording software; then
launch the program to add the Network Camera to the Channel list. For detailed information
about how to use the recording software, please refer to the user’s manual of the software or
download it from http://www.vivotek.com.
User's Manual - 17
VIVOTEK
Main Page
This chapter explains the layout of the main page. It is composed of the following sections:
VIVOTEK INC. Logo, Host Name, Camera Control Area, Configuration Area, Menu, and Live
Video Window.
VIVOTEK INC. Logo
Camera Control Area
Configuration Area
Host Name
Live View Window
VIVOTEK INC. Logo
Click this logo to visit the VIVOTEK website.
Host Name
The host name can be customized to fit your needs. For more information, please refer to System on page
24.
Camera Control Area
Video Stream: This Network Cmera supports multiple streams (stream 1 ~ 4) simultaneously. You can
select either one for live viewing. For more information about multiple streams, please refer to page 57
for detailed information.
Configuration Area
Client Settings: Click this button to access the client setting page. For more information, please refer to
Client Settings on page 21.
Configuration: Click this button to access the configuration page of the Network Camera. It is suggested
that a password be applied to the Network Camera so that only the administrator can configure the
Network Camera. For more information, please refer to Configuration on page 23.
Language: Click this button to choose a language for the user interface. Language options are available
in: English, Deutsch, Español, Français, Italiano, 日本語, Português, 簡体中文, and 繁體中文.
18 - User's Manual
VIVOTEK
Live Video Window
■ The following window is displayed when the video mode is set to H.264 / MPEG-4:
MPEG-4 Protocol and Media Options
Video Title
Title and Time
2010/03/23 13:44:17
Time
Video 13:44:17 2010/03/23
Video Control Buttons
Video Title: The video title can be configured. For more information, please refer to Video Settings on
page 52.
H.264 / MPEG-4 Protocol and Media Options: The transmission protocol and media options for H.264 /
MPEG-4 video streaming. For further configuration, please refer to Client Settings on page 21.
Time: Display the current time. For further configuration, please refer to Video Settings on page 52.
Title and Time: The video title and time can be stamped on the streaming video. For further configuration,
please refer to Video Settings on page 52.
Video Control Buttons: Depending on the Network Camera model and Network Camera configuration,
some buttons may not be available.
Snapshot: Click this button to capture and save still images. The captured images will be displayed
in a pop-up window. Right-click the image and choose Save Picture As to save it in JPEG (*.jpg) or BMP
(*.bmp) format.
Digital Zoom: Click and uncheck “Disable digital zoom” to enable the zoom operation. The navigation
screen indicates the part of the image being magnified. To control the zoom level, drag the slider bar. To
move to a different area you want to magnify, drag the navigation screen.
Pause: Pause the transmission of the streaming media. The button becomes the
after clicking the Pause button.
Stop: Stop the transmission of the streaming media. Click the
transmission.
Resume button
Resume button to continue
Start MP4 Recording: Click this button to record video clips in MP4 file format to your computer.
Stop MP4 Recording button to end recording. When you exit the web browser, video
Press the
recording stops accordingly. To specify the storage destination and file name, please refer to MP4 Saving
Options on page 22 for details.
User's Manual - 19
VIVOTEK
Full Screen: Click this button to switch to full screen mode. Press the “Esc” key to switch back to normal
mode.
■ The following window is displayed when the video mode is set to MJPEG:
Video Title
Title and Time
2010/03/23 13:44:17
Time
Video 13:44:17 2010/03/23
Video Control Buttons
Video Title: The video title can be configured. For more information, please refer to Video Settings on
page 52.
Time: Display the current time. For more information, please refer to Video Settings on page 52.
Title and Time: Video title and time can be stamped on the streaming video. For more information, please
refer to Video Settings on page 52.
Video Control Buttons: Depending on the Network Camera model and Network Camera configuration,
some buttons may not be available.
Snapshot: Click this button to capture and save still images. The captured images will be displayed
in a pop-up window. Right-click the image and choose Save Picture As to save it in JPEG (*.jpg) or BMP
(*.bmp) format.
Digital Zoom: Click and uncheck “Disable digital zoom” to enable the zoom operation. The navigation
screen indicates the part of the image being magnified. To control the zoom level, drag the slider bar. To
move to a different area you want to magnify, drag the navigation screen.
Start MP4 Recording: Click this button to record video clips in MP4 file format to your computer.
Stop MP4 Recording button to end recording. When you exit the web browser, video
Press the
recording stops accordingly. To specify the storage destination and file name, please refer to MP4 Saving
Options on page 22 for details.
Full Screen: Click this button to switch to full screen mode. Press the “Esc” key to switch back to
normal mode.
20 - User's Manual
VIVOTEK
Client Settings
This chapter explains how to select the stream transmission mode and saving options on the
local computer. When completed with the settings on this page, click Save on the page bottom
to enable the settings.
H.264 / MPEG-4 Protocol Options
H.264/MPEG-4 Protocol Options
Depending on your network environment, there are four transmission modes of H.264 or MPEG-4
streaming:
UDP unicast: This protocol allows for more real-time video streams. However, network packets may be
lost due to network burst traffic and images may be broken. Activate UDP connection when occasions
require time-sensitive responses and the video quality is less important. Note that each unicast client
connecting to the server takes up additional bandwidth and the Network Camera allows up to ten
simultaneous accesses.
UDP multicast: This protocol allows multicast-enabled routers to forward network packets to all clients
requesting streaming media. This helps to reduce the network transmission load of the Network Camera
while serving multiple clients at the same time. Note that to utilize this feature, the Network Camera must
be configured to enable multicast streaming at the same time. For more information, please refer to
RTSP Streaming on page 45.
TCP: This protocol guarantees the complete delivery of streaming data and thus provides better video
quality. The downside of this protocol is that its real-time effect is not as good as that of the UDP protocol.
HTTP: This protocol allows the same quality as TCP protocol without needing to open specific ports for
streaming under some network environments. Users inside a firewall can utilize this protocol to allow
streaming data through.
User's Manual - 21
VIVOTEK
MP4 Saving Options
Users can record live video as they are watching it by clicking
page. Here, you can specify the storage destination and file name.
Start MP4 Recording on the main
Folder: Specify a storage destination for the recorded video files.
File name prefix: Enter the text that will be appended to the front of the video file name.
Add date and time suffix to the file name: Select this option to append the date and time to the end of the
file name.
CLIP_20100323-180853
File name prefix Date and time suffix
The format is: YYYYMMDD_HHMMSS
Local Streaming Buffer Time
Due to the unsteady bandwidth flow, the live streaming may lag and not be very smoothly. If you enable
this option, the live streaming will be stored on the camera’s buffer area for a few seconds before playing
on the live viewing window. This will help you see the streaming more smoothly.
If you enter 3000 Millisecond, the streaming will delay 3 seconds.
22 - User's Manual
VIVOTEK
Configuration
Click Configuration on the main page to enter the camera setting pages. Note that only
Administrators can access the configuration page.
VIVOTEK offers an easy-to-use user interface that helps you set up your network camera with
minimal effort. To simplify the setting procedure, two types of user interfaces are available:
Advanced Mode for professional users and Basic Mode for entry-level users. Some advanced
functions (HTTPS/ Access list/ Homepage layout/ Application/ Recording/ System log/ View
parameters) are not displayed in Basic Mode.
If you want to set up advanced functions, please click [Advanced Mode] on the bottom of the
configuration list to quickly switch to Advanced Mode.
In order to simplify the user interface, the detailed information will be hidden unless you click on
the function item. When you click on the first sub-item, the detailed information for the first subitem will be displayed; when you click on the second sub-item, the detailed information for the
second sub-item will be displayed and that of the first sub-item will be hidden.
The following is the interface of the Basic Mode and the Advanced Mode:
Basic Mode
Configuration List
Click to switch to Advanced Mode
Firmware Version
User's Manual - 23
VIVOTEK
Advanced Mode
Configuration List
Click to switch to Basic Mode
Firmware Version
Each function on the configuration list will be explained in the following sections. Those functions that are
displayed only in Advanced Mode are marked with Advanced Mode . If you want to set up advanced
functions, please click [Advanced Mode] on the bottom of the configuration list to quickly switch over.
System
This section explains how to configure the basic settings for the Network Camera, such as the
host name and system time. It is composed of the following three columns: System, System
Time and DI and DO. When finished with the settings on this page, click Save at the bottom of
the page to enable the settings.
System
Host name: Enter a desired name for the Network Camera. The text will be displayed at the top of the
main page.
Turn off the LED indicators: If you do not want to let others know that the network camera is in operation,
you can select this option to turn off the LED indicators.
24 - User's Manual
VIVOTEK
System Time
Keep current date and time: Select this option to preserve the current date and time of the Network
Camera. The Network Camera’s internal real-time clock maintains the date and time even when the
power of the system is turned off.
Synchronize with computer time: Select this option to synchronize the date and time of the Network
Camera with the local computer. The read-only date and time of the PC is displayed as updated.
Manual: The administrator can enter the date and time manually. Note that the date and time format are
[yyyy/mm/dd] and [hh:mm:ss].
Automatic: The Network Time Protocol is a protocol which synchronizes computer clocks by periodically
querying an NTP Server.
NTP server: Assign the IP address or domain name of the time-server. Leaving the text box blank
connects the Network Camera to the default time servers.
Update interval: Select to update the time using the NTP server on an hourly, daily, weekly, or monthly
basis.
Time zone Advanced Mode : Select the appropriate time zone from the list. If you want to upload
Daylight Savings Time rules on the Maintenance page, please refer to Upload / Export Daylight Saving
Time Configuration File on page 92 for details.
Digital Input
Digital input: Select High or Low to define normal status for the digital input. The Network Camera will
report the current status.
User's Manual - 25
VIVOTEK
Security
This section explains how to enable password protection and create multiple accounts.
Root Password
The administrator account name is “root”, which is permanent and can not be deleted. If you want to add
more accounts in the Manage User column, please apply the password for the “root” account first.
1. Type the password identically in both text boxes, then click Save to enable password protection.
2. A window will be prompted for authentication; type the correct user’s name and password in their
respective fields to access the Network Camera.
Manage Privilege Advanced Mode
Allow anonymous viewing: If you check this item, any client can access the live stream without entering a
User ID and Password.
Manage User
Administrators can add up to 20 user accounts.
1. Input the new user’s name and password.
2. Select the privilege level for the new user account. Click Add to enable the setting.
Access rights are sorted by user privilege (Administrator, Operator, and Viewer). Only administrators can
access the Configuration page. Though operators cannot access the Configuration page, they can use
the URL Commands to get and set the value of parameters. For more information, please refer to URL
Commands of the Network Camera on page 95. Viewers access only the main page for live viewing.
Here you also can change a user’s access rights or delete user accounts.
1. Select an existing account to modify.
2. Make necessary changes and click Update or Delete to enable the setting.
26 - User's Manual
VIVOTEK
HTTPS (Hypertext Transfer Protocol over SSL)
Advanced Mode
This section explains how to enable authentication and encrypted communication over SSL
(Secure Socket Layer). It helps protect streaming data transmission over the Internet on higher
security level.
Enable HTTPS
Check this item to enable HTTPS communication, then select a connection option: "HTTP & HTTPS"
or "HTTPS only". Note that you have to create and install a certificate first in the second column before
clicking the Save button.
Create and Install Certificate Method
Before using HTTPS for communication with the Network Camera, a Certificate must be created first.
There are three ways to create and install a certificate:
Create self-signed certificate automatically
1. Select this option.
2. In the first column, check Enable HTTPS secure connection, then select a connection option: “HTTP
& HTTPS” or “HTTPS only”.
3. Click Save to generate a certificate.
User's Manual - 27
VIVOTEK
4. The Certificate Information will automatically be displayed in the third column as shown below. You can
click Property to view detailed information about the certificate.
5. Click Home to return to the main page. Change the address from “http://” to “https://“ in the address
bar and press Enter on your keyboard. Some Security Alert dialogs will pop up. Click OK or Yes to
enable HTTPS.
https://
https://192.168.5.151/index.html
28 - User's Manual
VIVOTEK
Create self-signed certificate manually
1. Select this option.
2. Click Create to open the Create Certificate page, then click Save to generate the certificate.
3. The Certificate Information will automatically be displayed in the third column as shown below. You
can click Property to see detailed information about the certificate.
Create certificate and install : Select this option if you want to create a certificate from a certificate
authority.
1. Select this option.
2. Click Create to open the Create Certificate page, then click Save to generate the certificate.
User's Manual - 29
VIVOTEK
3. If you see the following Information bar, click OK and click on the Information bar at the top of the page
to allow pop-ups.
4. The pop-up window shows an example of a certificate request.
30 - User's Manual
VIVOTEK
5. Look for a trusted certificate authority that issues digital certificates. Enroll the Network Camera.
Wait for the certificate authority to issue a SSL certificate; click Browse... to search for the issued
certificate, then click Upload in the second column.
NOTE
► How do I cancel the HTTPS settings?
1. Uncheck Enable HTTPS secure connection in the first column and click Save; a warning dialog
will pop up.
2. Click OK to disable HTTPS.
3. The webpage will redirect to a non-HTTPS page automatically.
► If you want to create and install other certificates, please remove the existing one. To remove the
signed certificate, uncheck Enable HTTPS secure connection in the first column and click Save.
Then click Remove to erase the certificate.
User's Manual - 31
VIVOTEK
SNMP (Simple Network Management Protocol)
Advanced Mode
This section explains how to use the SNMP on the network camera. The Simple Network
Management Protocol is an application layer protocol that facilitates the exchange of
management information between network devices. It helps network administrators to remotely
manage network devices and find, solve network problems with ease.
■ The SNMP consists of the following three key components:
1. Manager: Network-management station (NMS), a server which executes applications that monitor and
control managed devices.
2. Agent: A network-management software module on a managed device which transfers the status of
managed devices to the NMS.
3. Managed device: A network node on a managed network. For example: routers, switches, bridges,
hubs, computer hosts, printers, IP telephones, network cameras, web server, and database.
Before configuring SNMP settings on the this page, please enable your NMS first.
SNMP Configuration
Enable SNMPv1, SNMPv2c
Select this option and enter the names of Read/Write community and Read Only community according to
your NMS settings.
Enable SNMPv3
This option contains cryptographic security, a higher security level, which allows you to set the
Authentication password and the Encryption password.
■ Security name: According to your NMS settings, choose Read/Write or Read Only and enter the
community name.
■ Authentication type: Select MD5 or SHA as the authentication method.
■ Authentication password: Enter the password for authentication (at least 8 characters).
■ Encryption password: Enter a password for encryption (at least 8 characters).
32 - User's Manual
VIVOTEK
Network
This section explains how to configure a wired network connection for the Network Camera.
Network Type
LAN
Select this option when the Network Camera is deployed on a local area network (LAN) and is intended
to be accessed by local computers. The default setting for the Network Type is LAN. Rememer to click
Save when you complete the Network setting.
Get IP address automatically: Select this option to obtain an available dynamic IP address assigned by
the DHCP server each time the camera is connected to the LAN.
Use fixed IP address: Select this option to manually assign a static IP address to the Network Camera.
1. You can make use of VIVOTEK Installation Wizard 2 on the software CD to easily set up the Network
Camera on LAN. Please refer to Software Installation on page 12 for details.
2. Enter the Static IP, Subnet mask, Default router, and Primary DNS provided by your ISP.
Subnet mask: This is used to determine if the destination is in the same subnet. The default value is
“255.255.255.0”.
Default router: This is the gateway used to forward frames to destinations in a different subnet. Invalid
router setting will fail the transmission to destinations in different subnet.
User's Manual - 33
VIVOTEK
Primary DNS: The primary domain name server that translates hostnames into IP addresses.
Secondary DNS: Secondary domain name server that backups the Primary DNS.
Primary WINS server: The primary WINS server that maintains the database of computer name and IP
address.
Secondary WINS server: The secondary WINS server that maintains the database of computer name
and IP address.
Enable UPnP presentation: Select this option to enable UPnPTM presentation for your Network Camera
so that whenever a Network Camera is presented to the LAN, shortcuts of connected Network Cameras
will be listed in My Network Places. You can click the shortcut to link to the web browser. Currently,
UPnPTM is supported by Windows XP or later. Note that to utilize this feature, please make sure the
UPnPTM component is installed on your computer.
Mega-pixel Network Camera (192.168.5.151)
Enable UPnP port forwarding: To access the Network Camera from the Internet, select this option to
allow the Network Camera to open ports on the router automatically so that video streams can be sent
out from a LAN. To utilize of this feature, make sure that your router supports UPnPTM and it is activated.
PPPoE (Point-to-point over Ethernet)
Select this option to configure your Network Camera to make it accessible from anywhere as long as
there is an Internet connection. Note that to utilize this feature, it requires an account provided by your
ISP.
Follow the steps below to acquire your Network Camera’s public IP address.
1. Set up the Network Camera on the LAN.
2. Go to Home > Configuration > Application > Server Settings (please refer to Server Settings on page
75) to add a new email or FTP server.
3. Go to Configuration > Application > Media Settings (please refer to Media Settings on page 78). Select
System log so that you will receive the system log in TXT file format which contains the Network
Camera’s public IP address in your email or on the FTP server.
4. Go to Configuration > Network > Network Type. Select PPPoE and enter the user name and password
provided by your ISP. Click Save to enable the setting.
5. The Network Camera will reboot.
6. Disconnect the power to the Network Camera; remove it from the LAN environment.
34 - User's Manual
VIVOTEK
NOTE
► If the default ports are already used by other devices connected to the same router, the Network
Camera will select other ports for the Network Camera.
► If UPnP TM is not supported by your router, you will see the following message:
Error: Router does not support UPnP port forwarding.
► Steps to enable the UPnP TM user interface on your computer:
Note that you must log on to the computer as a system administrator to install the UPnP TM
components.
1. Go to Start, click Control Panel, then click Add or Remove Programs.
2. In the Add or Remove Programs dialog box, click Add/Remove Windows Components.
3. In the Windows Components Wizard dialog box, select Networking Services and click Details.
User's Manual - 35
VIVOTEK
4. In the Networking Services dialog box, select Universal Plug and Play and click OK.
5. Click Next in the following window.
6. Click Finish. UPnP TM is enabled.
► How does UPnP TM work?
UPnP TM networking technology provides automatic IP configuration and dynamic discovery of devices
added to a network. Services and capabilities offered by networked devices, such as printing and file
sharing, are available among each other without the need for cumbersome network configuration. In
the case of Network Cameras, you will see Network Camera shortcuts under My Network Places.
► Enabling UPnP port forwarding allows the Network Camera to open a secondary HTTP port on the
router-not HTTP port-meaning that you have to add the secondary HTTP port number to the Network
Camera’s public address in order to access the Network Camera from the Internet. For example,
when the HTTP port is set to 80 and the secondary HTTP port is set to 8080, refer to the list below for
the Network Camera’s IP address.
From the Internet
http://203.67.124.123:8080
In LAN
http://192.168.4.160 or
http://192.168.4.160:8080
► If the PPPoE settings are incorrectly configured or the Internet access is not working, restore the
Network Camera to factory default; please refer to Restore on page 91 for details. After the Network
Camera is reset to factory default, it will be accessible on the LAN.
36 - User's Manual
VIVOTEK
Enable IPv6
Select this option and click Save to enable IPv6 settings.
Please note that this only works if your network environment and hardware equipment support IPv6. The
browser should be Microsoft® Internet Explorer 6.5, Mozilla Firefox 3.0 or above.
When IPv6 is enabled, by default, the network camera will listen to router advertisements and be
assigned with a link-local IPv6 address accordingly.
IPv6 Information: Click this button to obtain the IPv6 information as shown below.
If your IPv6 settings are successful, the IPv6 address list will be listed in the pop-up window. The IPv6
address will be displayed as follows:
Refers to Ethernet
Link-global IPv6 address/network mask
Link-local IPv6 address/network mask
User's Manual - 37
VIVOTEK
Please follow the steps below to link to an IPv6 address:
1. Open your web browser.
2. Enter the link-global or link-local IPv6 address in the address bar of your web browser.
3. The format should be:
http://[2001:0c08:2500:0002:0202:d1ff:fe04:65f4]/
IPv6 address
4. Press Enter on the keyboard or click Refresh button to refresh the webpage.
For example:
NOTE
► If you have a Secondary HTTP port (the default value is 8080), you can also link to the webpage in
the following address format: (Please refer to HTTP on page 43 for detailed information.)
http://[2001:0c08:2500:0002:0202:d1ff:fe04:65f4]/:8080
IPv6 address
Secondary HTTP port
► If you choose PPPoE as the Network Type, the [PPP0 address] will be displayed in the IPv6
information column as shown below.
Manually setup the IP address: Select this option to manually set up IPv6 settings if your network
environment does not have DHCPv6 server and advertisements-enabled routers.
If you check this item, the following blanks will be displayed for you to enter the corresponding
information:
38 - User's Manual
VIVOTEK
IEEE 802.1x Advanced Mode
Enable this function if your network environment uses IEEE 802.1x, which is a port-based network
access control. The network devices, intermediary switch/access point/hub, and RADIUS server must
support and enable 802.1x settings.
The 802.1x standard is designed to enhance the security of local area networks, which provides
authentication to network devices (clients) attached to a network port (wired or wireless). If all certificates
between client and server are verified, a point-to-point connection will be enabled; if authentication fails,
access on that port will be prohibited. 802.1x utilizes an existing protocol, the Extensible Authentication
Protocol (EAP), to facilitate communication.
■ The components of a protected network with 802.1x authentication:
Supplicant
(Network Camera)
Authenticator
(Network Switch)
Authentication Server
(RADIUS Server)
1. Supplicant: A client end user (camera), which requests authentication.
2. Authenticator (an access point or a switch): A “go between” which restricts unauthorized end users
from communicating with the authentication server.
3. Authentication server (usually a RADIUS server): Checks the client certificate and decides whether to
accept the end user’s access request.
■ VIVOTEK Network Cameras support two types of EAP methods to perform authentication: EAP-PEAP
and EAP-TLS.
Please follow the steps below to enable 802.1x settings:
1. Before connecting the Network Camera to the protected network with 802.1x, please apply a digital
certificate from a Certificate Authority (ie. MIS of your company) which can be validated by a RADIUS
server.
2. Connect the Network Camera to a PC or notebook outside of the protected LAN. Open the
configuration page of the Network Camera as shown below. Select EAP-PEAP or EAP-TLS as the
EAP method. In the following blanks, enter your ID and password issued by the CA, then upload
related certificate(s).
User's Manual - 39
VIVOTEK
3. When all settings are complete, move the Network Camera to the protected LAN by connecting it to an
802.1x enabled switch. The devices will then start the authentication automatically.
NOTE
► The authentication process for 802.1x:
1. The Certificate Authority (CA) provides the required signed certificates to the Network Camera (the
supplicant) and the RADIUS Server (the authentication server).
2. A Network Camera requests access to the protected LAN using 802.1X via a switch (the authenticator).
The client offers its identity and client certificate, which is then forwarded by the switch to the RADIUS
Server, which uses an algorithm to authenticate the Network Camera and returns an acceptance or
rejection back to the switch.
3. The switch also forwards the RADIUS Server’s certificate to the Network Camera.
4. Assuming all certificates are validated, the switch then changes the Network Camera’s state to
authorized and is allowed access to the protected network via a pre-configured port.
1
Certificate
Certificate Authority
(CA)
1
Certificate
2
4
VIVOTEK
Network Camera
Network Switch
3
RADIUS Server
Protected LAN
40 - User's Manual
VIVOTEK
QoS (Quality of Service) Advanced Mode
Quality of Service refers to a resource reservation control mechanism, which guarantees a certain quality
to different services (voice, data, video, etc) on the network. Quality of service guarantees are important
if the network capacity is insufficient, especially for real-time streaming multimedia applications. Quality
can be defined as, for instance, a maintained level of bit rate, low latency, no packet dropping, etc.
The following are the main benefits of a QoS-aware network:
■ The ability to prioritize traffic and guarantee a certain level of performance to the data flow.
■ The ability to control the amount of bandwidth each application may use, and thus provide higher
reliability and stability on the network.
Requirements for QoS
To utilize QoS in a network environment, the following requirements must be met:
■ All network switches and routers in the network must include support for QoS.
■ The network video devices used in the network must be QoS-enabled.
QoS models
CoS (the VLAN 802.1p model)
IEEE802.1p defines a QoS model at OSI Layer 2 (Data Link Layer), which is called CoS, Class of
Service. It adds a 3-bit value to the VLAN MAC header, which indicates the frame priority level from 0
(lowest) to 7 (highest). The priority is set up on the network switches, which then use different queuing
disciplines to forward the packets.
Below is the setting column for CoS. Enter the VLAN ID of your switch (0~4095) and choose the priority
for each application (0~7).
If you assign Video the highest level, the switch will handle video packets first.
NOTE
► The VLAN Switch (802.1p) is required. The web browsing may fail if the CoS setting is incorrect.
► Class of Service technologies do not guarantee a level of service in terms of bandwidth and delivery
time; they offer a "best-effort." Users can think of CoS as "coarsely-grained" traffic control and QoS as
"finely-grained" traffic control.
► Though CoS is simple to manage, it lacks scalability and does not offer end-to-end guarantees since it
is based on L2 protocol.
User's Manual - 41
VIVOTEK
QoS/DSCP (the DiffServ model)
DSCP-ECN defines QoS at Layer 3 (Network Layer). The Differentiated Services (DiffServ) model is
based on packet marking and router queuing disciplines. The marking is done by adding a field to the
IP header, called the DSCP (Differentiated Services Codepoint). This is a 6-bit field that provides 64
different class IDs. It gives an indication of how a given packet is to be forwarded, known as the Per Hop
Behavior (PHB). The PHB describes a particular service level in terms of bandwidth, queueing theory,
and dropping (discarding the packet) decisions. Routers at each network node classify packets according
to their DSCP value and give them a particular forwarding treatment; for example, how much bandwidth
to reserve for it.
Below are the setting options of DSCP (DiffServ Codepoint). Specify the DSCP value for each application
(0~63).
42 - User's Manual
VIVOTEK
HTTP Advanced Mode
To utilize HTTP authentication, make sure that your have set a password for the Network Camera first;
please refer to Security on page 26 for details.
Authentication: Depending on your network security requirements, the Network Camera provides two
types of security settings for an HTTP transaction: basic and digest.
If basic authentication is selected, the password is sent in plain text format and there can be potential
risks of being intercepted. If digest authentication is selected, user credentials are encrypted using MD5
algorithm and thus provide better protection against unauthorized accesses.
HTTP port / Secondary HTTP port: By default, the HTTP port is set to 80 and the secondary HTTP port is
set to 8080. They can also be assigned to another port number between 1025 and 65535. If the ports are
incorrectly assigned, the following warning messages will be displayed:
To access the Network Camera on the LAN, both the HTTP port and secondary HTTP port can be used
to access the Network Camera. For example, when the HTTP port is set to 80 and the secondary HTTP
port is set to 8080, refer to the list below for the Network Camera’s IP address.
On the LAN
http://192.168.4.160 or
http://192.168.4.160:8080
Access name for stream 1 ~ 5: This Network camera supports multiple streams simultaneously. The
access name is used to differentiate the streaming source. Users can click Configuration > Video >
Video Settings to set up the video quality of linked streams. For more information about how to set up
the video quality, please refer to Viewing Windows on page 57.
When using Mozilla Firefox or Netscape to access the Network Camera and the video mode is set to
JPEG, users will receive video comprised of continuous JPEG images. This technology, known as “server
push”, allows the Network Camera to feed live pictures to Mozilla Firefox and Netscape.
User's Manual - 43
VIVOTEK
URL command -- http://<ip address>:<http port>/<access name for stream 1 ~ 5>
For example, when the Access name for stream 2 is set to video2.mjpg:
1. Launch Mozilla Firefox or Netscape.
2. Type the above URL command in the address bar. Press Enter.
3. The JPEG images will be displayed in your web browser.
http://192.168.5.151/video2.mjpg
NOTE
► Microsoft ® Internet Explorer does not support server push technology; therefore, using http://<ip
address>:<http port>/<access name for stream 1 ~ 5> will fail to access the Network Camera.
► Users can only use URL commands to request the stream 5. For more information about URL
commands, please refer to page 95.
HTTPS
By default, the HTTPS port is set to 443. It can also be assigned to another port number between 1025
and 65535.
FTP
The FTP server allows the user to save recorded video clips. You can utilize VIVOTEK's Installation
Wizard 2 to upgrade the firmware via FTP server. By default, the FTP port is set to 21. It also can be
assigned to another port number between 1025 and 65535.
44 - User's Manual
VIVOTEK
RTSP Streaming
To utilize RTSP streaming authentication, make sure that you have set a password for the Network
Camera first; please refer to Security on page 26 for details.
Authentication: Depending on your network security requirements, the Network Camera provides three
types of security settings for streaming via RTSP protocol: disable, basic, and digest.
If basic authentication is selected, the password is sent in plain text format, but there can be potential
risks of it being intercepted. If digest authentication is selected, user credentials are encrypted using
MD5 algorithm, thus providing better protection against unauthorized access.
The availability of the RTSP streaming for the three authentication modes is listed in the following table:
Disable
Basic
Digest
Quick Time player
Real Player
O
O
O
O
O
X
Access name for stream 1 ~ 5: This Network Camera supports multiple streams simultaneously. The
access name is used to differentiate the streaming source.
If you want to use an RTSP player to access the Network Camera, you have to set the video mode to
H.264 / MPEG-4 and use the following RTSP URL command to request transmission of the streaming
data.
rtsp://<ip address>:<rtsp port>/<access name for stream1 ~ 5>
For example, when the access name for stream 1 is set to live.sdp:
1. Launch an RTSP player.
2. Choose File > Open URL. A URL dialog box will pop up.
3. Type the above URL command in the text box.
rtsp://192.168.5.151:554/live.sdp
4. The live video will be displayed in your player as shown
below.
Video 16:38:01 2010/03/23
User's Manual - 45
VIVOTEK
RTSP port /RTP port for video/ RTCP port for video
■ RTSP (Real-Time Streaming Protocol) controls the delivery of streaming media. By default, the port
number is set to 554.
■ The RTP (Real-time Transport Protocol) is used to deliver video data to the clients. By default, the RTP
port for video is set to 5556.
■ The RTCP (Real-time Transport Control Protocol) allows the Network Camera to transmit the data by
monitoring the Internet traffic volume. By default, the RTCP port for video is set to 5557.
The ports can be changed to values between 1025 and 65535. The RTP port must be an even number
and the RTCP port is the RTP port number plus one, and thus is always an odd number. When the RTP
port changes, the RTCP port will change accordingly.
If the RTP ports are incorrectly assigned, the following warning message will be displayed:
Multicast settings for stream 1 ~ 4: Click the items to display the detailed configuration information.
Select the Always multicast option to enable multicast for stream 1 ~ 4.
Unicast video transmission delivers a stream through point-to-point transmission; multicast, on the other
hand, sends a stream to the multicast group address and allows multiple clients to acquire the stream at
the same time by requesting a copy from the multicast group address. Therefore, enabling multicast can
effectively save Internet bandwith.
The ports can be changed to values between 1025 and 65535. The multicast RTP port must be an even
number and the multicast RTCP port number is the multicast RTP port number plus one, and thus is
always odd. When the multicast RTP port changes, the multicast RTCP port will change accordingly.
If the multicast RTP video ports are incorrectly assigned, the following warning message will be
displayed:
Multicast TTL [1~255]: The multicast TTL (Time To Live) is the value that tells the router the range a
packet can be forwarded.
46 - User's Manual
VIVOTEK
DDNS
This section explains how to configure the dynamic domain name service for the Network
Camera. DDNS is a service that allows your Network Camera, especially when assigned with a
dynamic IP address, to have a fixed host and domain name.
DDNS: Dynamic domain name service
Enable DDNS: Select this option to enable the DDNS setting.
Provider: Select a DDNS provider from the provider drop-down list.
VIVOTEK offers Safe100.net, a free dynamic domain name service, to VIVOTEK customers. It is
recommended that you register Safe100.net to access VIVOTEK’s Network Cameras from the Internet.
Additionally, we offer other DDNS providers, such as Dyndns.org(Dynamic), Dyndns.org(Custom), TZO.
com, DHS.org, CustomSafe100, dyn-interfree.it.
Note that before utilizing this function, please apply for a dynamic domain account first.
■ Safe100.net
1. In the DDNS column, select Safe100.net from the drop-down list. Click I accept after reviewing the
terms of the Service Agreement.
2. In the Register column, fill in the Host name (xxxx.safe100.net), Email, Key, and Confirm Key, and
click Register. After a host name has been successfully created, a success message will be displayed
in the DDNS Registration Result column.
[Register] Successfully Your account information has
been mailed to registered e-mail address
3. Click Copy and all the registered information will automatically be uploaded to the corresponding fields
in the DDNS column at the top of the page as seen in the picture.
User's Manual - 47
VIVOTEK
[Register] Successfully Your account information has
been mailed to registered e-mail address
4. Select Enable DDNS and click Save to enable the setting.
■ CustomSafe100
VIVOTEK offers documents to establish a CustomSafe100 DDNS server for distributors and system
integrators. You can use CustomSafe100 to register a dynamic domain name if your distributor or system
integrators offer such services.
1. In the DDNS column, select CustomSafe100 from the drop-down list.
2. In the Register column, fill in the Host name, Email, Key, and Confirm Key; then click Register. After a
host name has been successfully created, you will see a success message in the DDNS Registration
Result column.
3. Click Copy and all for the registered information will be uploaded to the corresponding fields in the
DDNS column.
4. Select Enable DDNS and click Save to enable the setting.
Forget key: Click this button if you have forgotten the key to Safe100.net or CustomSafe100. Your
account information will be sent to your email address.
Refer to the following links to apply for a dynamic domain account when selecting other DDNS
providers:
■ Dyndns.org(Dynamic) / Dyndns.org(Custom): visit http://www.dyndns.com/
■ TZO.com: visit http://www.tzo.com/
■ DHS.org: visit http://www.dhs.org/
■ dyn-interfree.it: visit http://dyn-interfree.it/
48 - User's Manual
VIVOTEK
Access List
Advanced Mode
This section explains how to control access permission by verifying the client PC’s IP address.
General Settings
Maximum number of concurrent streaming connection(s) limited to: Simultaneous live viewing for 1~10
clients (including stream 1 ~ stream 5). The default value is 10. If you modify the value and click Save, all
current connections will be disconnected and automatically attempt to re-link (IE Explore or Quick Time
Player).
View Information: Click this button to display the connection status window showing a list of the current
connections.
For example:
Connection status
IP address
Elapsed time
192.168.1.147
12:20:34
root
61.22.15.3
00:10:09
anonymous
192.168.3.25
45:00:34
greg
Refresh
Add to Deny List
User ID
Disconnect
■ IP address: Current connections to the Network Camera.
■ Elapsed time: How much time the client has been at the webpage.
■ User ID: If the administrator has set a password for the webpage, the clients have to enter a user name
and password to access the live video. The user name will be displayed in the User ID column. If the
administrator allows clients to link to the webpage without a user name and password, the User ID
column will be empty.
There are some situations which allow clients access to the live video without a user name and
password:
1. The administrator does not set up a root password. For more information about how to set up a root
password and manage user accounts, please refer to Security on page 26.
2. The administrator has set up a root password, but set RTSP Authentication to “disable“. For more
information about RTSP Authentication, please refer to RTSP Streaming on page 45.
3. The administrator has set up a root password, but allows anonymous viewing. For more information
about Allow Anonymous Viewing, please refer to Security on page 26.
User's Manual - 49
VIVOTEK
■ Refresh: Click this button to refresh all current connections.
■ Add to deny list: You can select entries from the Connection Status list and add them to the Deny List
to deny access. Please note that those checked connections will only be disconnected temporarily
and will automatically try to re-link again (IE Explore or Quick Time Player). If you want to enable the
denied list, please check Enable access list filtering and click Save in the first column.
■ Disconnect: If you want to break off the current connections, please select them and click this
button. Please note that those checked connections will only be disconnected temporarily and will
automatically try to re-link again (IE Explore or Quick Time Player).
Enable access list filtering: Check this item and click Save if you want to enable the access list filtering
function.
Filter Type
Select Allow or Deny as the filter type. If you choose Allow Type, only those clients whose IP addresses
are on the Access List below can access the Network Camera, and the others cannot access. On the
contrary, if you choose Deny Type, those clients whose IP addresses are on the Access List below will
not be allowed to access the Network Camera, and the others can access.
Filter
Then you can add a rule to the following Access List. Please note that the IPv6 access list column will not
be displayed unless you enable IPv6 on the Network page. For more information about IPv6 Settings,
please refer to page 37 for detailed information.
There are three types of rules:
Single: This rule allows the user to add an IP address to the Allowed/Denied list.
For example:
50 - User's Manual
VIVOTEK
Network: This rule allows the user to assign a network address and corresponding subnet mask to the
Allow/Deny List.
For example:
IP address 192.168.2.x will be blocked.
Range: This rule allows the user to assign a range of IP addresses to the Allow/Deny List.
Note: This rule is only applied to IPv4.
For example:
Administrator IP address
Always allow the IP address to access this device: You can check this item and add the Administrator’s
IP address in this field to make sure the Administrator can always connect to the device.
User's Manual - 51
VIVOTEK
Video
This section explains how to configure the video settings of the Network Camera.
Video Settings
Video title: Enter a name that will be displayed on the title bar of the live video.
Video Title
Title and Time
2010/03/23 13:44:17
Video 13:44:17 2010/03/23
Color: Select to display color or black/white video streams.
Power line frequency: Set the power line frequency consistent with local utility settings to eliminate image
flickering associated with fluorescent lights. Note that after the power line frequency is changed, you
must disconnect and reconnect the power cord of the Network Camera in order for the new setting to
take effect.
Select caching stream: This Network Camera supports time shift cache stream on the Network Camera.
Select one stream and check the below option Enable time shift caching stream.
Enable time shift caching stream Advanced Mode : Check this item to enable the time shift cache
stream on the Network Camera, which will stores video in the camera’s embedded memory for a period
of time depending on the cache memory of each Network Camera. This function can work seamlessly
with VIVOTEK’s recording software. When an event occurs, the recording software can request time shift
cache stream from the camera, which allows the user to get an earlier video data.
Video orientation: Flip--vertically reflect the display of the live video; Mirror--horizontally reflect the display
of the live video. Select both options if the Network Camera is installed upside-down (ex. on the ceiling)
to correct the image orientation. Please note that the preset locations will be cleared after flip/mirror.
52 - User's Manual
VIVOTEK
Overlay title and time stamp on video: Select this option to place the video title and time on the video
streams.
Note that when the frame size is set to 176 x 144 as shown in the picture below, only the time will be
stamped on the video streams.
2010/03/23 13:44:17
13:44:17 2010/03/23
Image Settings Advanced Mode
Click Image Settings to open the Image Settings page. On this page, you can tune the White balance,
Brightness, Saturation, Contrast, and Sharpness settings for the video.
2010/03/23 13:44:17
User's Manual - 53
VIVOTEK
White balance: Adjust the value for the best color temperature.
■ Auto
The Network Camera automatically adjusts the color temperature of the light in response to different light
sources. The white balance setting defaults to Auto and works well in most situations.
■ Keep current value
Follow the steps below to manually set the white balance to compensate for the ambient lighting
conditions.
1. Set the White balance to Auto and click Save.
2. Place a sheet of white paper in front of the lens, then allow the Network Camera to adjust the color
temperature automatically.
3. Select Keep Current Value to confirm the setting while the white balance is being measured.
4. Click Save to enable the new setting.
Image Adjustment
■ Brightness: Adjust the image brightness level, which ranges from -5 to +5.
■ Saturation: Adjust the image saturation level, which ranges from -5 to +5.
■ Contrast: Adjust the image contrast level, which ranges from -5 to +5.
■ Sharpness: Adjust the image sharpness level, which ranges from -5 to +5.
You can click Preview to fine-tune the image, or click Restore to recall the original settings without
incorporating the changes. When completed with the settings on this page, click Save to enable the
setting and click Close to exit the page.
Privacy Mask Advanced Mode
Click Privacy Mask to open the settings page. On this page, you can block out sensitive zones to
address privacy concerns.
2010/03/23 13:44:17
2010/03/23 13:44:17
■ To set the privacy mask windows, follow the steps below:
1. Click New to add a new window.
2. Use the mouse to size and drag-drop the window, which is recommended to be at least twice the size
of the object (height and width) you want to cover.
3. Enter a Window Name and click Save to enable the setting.
4. Select Enable privacy mask to enable this function.
54 - User's Manual
VIVOTEK
NOTE
► Up to 5 privacy mask windows can be set up on the same screen.
► If you want to delete the privacy mask window, please click the ‘x’ on the upper right-hand corner of
the window.
Sensor Settings Advanced Mode
Click Sensor Settings to open the Sensor Settings page. On this page, you can set the maximum
exposure time, exposure level, and AGC (Auto Gain Control) settings.
You can configure two sets of sensor settings: one for normal situations, the other for special situations,
such as day/night/schedule mode.
2010/03/23 13:44:17
Sensor Setting 1:
For normal situations
Sensor Setting 2:
For special situations
Exposure
■ Maximum Exposure Time: Select a proper maximum exposure time according to the light source of
the surroundings. Shorter exposure times result in less light. The exposure times are selectable for the
following durations: 1/30 second, 1/15 second, and 1/5 second.
■ Exposure level: You can manually set the Exposure level, which ranges from 1 to 8 (dark to bright).The
default value is 4.
■ Max gain (Auto Gain Control): You can manually set the AGC level (2X 4X, or 8X). The default value is
4X.
■ Enable BLC (Back Light Compensation): Enable this option when the object is too dark or too bright
to recognize. It allows the camera to adjust to the best light conditions in any environment and
automatically give the necessary light compensation.
User's Manual - 55
VIVOTEK
You can click Preview to fine-tune the image, or click Restore to recall the original settings without
incorporating the changes. When completed with the settings on this page, click Save to enable the
settings and click Close to exit the page.
If you want to configure another sensor setting for day/night/schedule mode, please click Profile to open
the Sensor Settings Profile Settings page as shown below.
2010/03/23 13:44:17
Please follow the steps beolw to setup a profile:
1. Check Enable this profile.
2. Select the applied mode: Day mode, Night mode, or schedule mode. Please manually enter a range of
time if you choose Schedule mode.
3. Configure Exposure settings in the second column. Please refer to the last page for detailed
information.
4. Click Save to enable the setting and click Close to exit the page.
56 - User's Manual
VIVOTEK
Viewing Window Advanced Mode
Click Viewing Window to open the Viewing Window Settings page.
This Network Camera supports multiple streams with frame size ranging from 176 x 144 to 1280 x 800.
The definition of multiple streams:
■ Stream 1: Users can define the "Region of Interest" (viewing region) and the "Output Frame Rate" (size
of the live view window).
■ Stream 2: Users can define the "Region of Interest" (viewing region) and the "Output Frame Rate" (size
of the live view window).
■ Stream 3: Users can define the "Region of Interest" (viewing region) and the "Output Frame Rate" (size
of the live view window).
■ Stream 4 (Global view stream): This stream captures the full view of the video and users can also
define the "Output Frame Rate" (size of the live view window).
Click Viewing Window to open the viewing region settings page. On this page, you can set the Region
of Interest and the Output Frame Size for stream 1 ~ 3.
Please follow the steps below to set up those settings for a stream:
1. Select a stream which you want to set up the viewing region.
2. Select a Region of Interest from the drop-down list, the floating frame will resize accordingly. If you
want to set up a customized viewing region, you can also resize and drag the floating frame to a
desired position with your mouse.
3. Choose a proper Output Frame Size from the drop-down list according to the size of your monitoring
device.
NOTE
► All the items in the “Region of Interest” should not be greater than the “Output Frame Size“ (current
maximum resolution).
User's Manual - 57
VIVOTEK
■ The parameters of the multiple streams:
Stream 1
Stream 2
Stream 3
Stream 4
Region of Interest
Output frame size
1280 X 800 ~ 176 x 144 (Selectable)
1280 X 800 ~ 176 x 144 (Selectable)
1280 X 800 ~ 176 x 144 (Selectable)
1280 X 800 (Fixed)
1280 X 800 ~ 176 x 144 (Selectable)
1280 X 800 ~ 176 x 144 (Selectable)
1280 X 800 ~ 176 x 144 (Selectable)
1280 X 800 ~ 176 x 144 (Selectable)
When completed with the settings in the Viewing Window, click Save to enable the settings and click
Close to exit the window. The selected Output Frame Size will immediately be applied to the Frame
size of video stream. Then you can go back to the home page to test the settings.
Output Frame Size
58 - User's Manual
VIVOTEK
Video Quality Settings Advanced Mode
Click the stream item to display the detailed information. This Network Camera offers real-time H.264,
MPEG-4 and MJEPG compression standards (Triple Codec) for real-time viewing. The maximum frame
size will follow your settings in the above Viewing Window sections.
If H.264 / MPEG-4 mode is selected, the video is streamed via RTSP protocol. There are four parameters
for you to adjust the video performance:
■ Frame size
You can set up different video resolution for different viewing devices. For example, set a smaller
frame size and lower bit rate for remote viewing on mobile phones and a larger video size and a higher
bit rate for live viewing on web browsers. Note that a larger frame size takes up more bandwidth.
■ Maximum frame rate
This limits the maximum refresh frame rate per second. Set the frame rate higher for smoother video
quality.
If the power line frequency is set to 50Hz, the frame rates are selectable at 1fps, 2fps, 3fps, 5fps,
8fps, 10fps, 15fps, 20fps, and 25fps. If the power line frequency is set to 60Hz, the frame rates are
selectable at 1fps, 2fps, 3fps, 5fps, 8fps, 10fps, 15fps, 20fps, 25fps, and 30fps. You can also select
Customize and manually enter a value. The frame rate will decrease if you select a higher resolution.
User's Manual - 59
VIVOTEK
■ Intra frame period
Determine how often to plant an I frame. The shorter the duration, the more likely you will get better
video quality, but at the cost of higher network bandwidth consumption. Select the intra frame period
from the following durations: 1/4 second, 1/2 second, 1 second, 2 seconds, 3 seconds, and 4 seconds.
■ Video quality
A complex scene generally produces a larger file size, meaning that higher bandwidth will be needed
for data transmission. Therefore, if Constant bit rate is selected, the bandwidth utilization is fixed at
a selected level, resulting in mutable video quality performance. The bit rates are selectable at the
following rates: 20Kbps, 30Kbps, 40Kbps, 50Kbps, 64Kbps, 128Kbps, 256Kbps, 512Kbps, 768Kbps,
1Mbps, 2Mbps, 3Mbps, 4Mbps, 6Mbps, and 8Mbps. You can also select Customize and manually
enter a value.
On the other hand, if Fixed quality is selected, all frames are transmitted with the same quality;
bandwidth utilization is therefore unpredictable. The video quality can be adjusted to the following
settings: Medium, Standard, Good, Detailed, and Excellent. You can also select Customize and
manually enter a value.
If JPEG mode is selected, the Network Camera continuously sends JPEG images to the client, producing
a moving effect similar to a filmstrip. Every single JPEG image transmitted guarantees the same
image quality, which in turn comes at the expense of variable bandwidth usage. Because the media
contents are a combination of JPEG images, no audio data is transmitted to the client. There are three
parameters provided in MJPEG mode to control the video performance:
■ Frame size
You can set up different video resolution for different viewing devices. For example, set a smaller
frame size and lower bit rate for remote viewing on mobile phones and a larger video size and a higher
bit rate for live viewing on web browsers. Note that a larger frame size takes up more bandwidth.
■ Maximum frame rate
This limits the maximum refresh frame rate per second. Set the frame rate higher for smoother video
quality.
If the power line frequency is set to 50Hz, the frame rates are selectable at 1fps, 2fps, 3fps, 5fps,
8fps, 10fps, 15fps, 20fps, and 25fps. If the power line frequency is set to 60Hz, the frame rates are
selectable at 1fps, 2fps, 3fps, 5fps, 8fps, 10fps, 15fps, 20fps, 25fps, and 30fps. You can also select
Customize and manually enter a value. The frame rate will decrease if you select a higher resolution.
■ Video quality
The video quality can be adjusted to the following settings: Medium, Standard, Good, Detailed, and
Excellent. You can also select Customize and manually enter a value.
NOTE
► Video quality and fixed quality refers to the compression rate, so a lower value will produce higher
quality.
► Converting high-quality video may significantly increase the CPU loading, and you may encounter
streaming disconnection or video loss while capturing a complicated scene. In the event of occurance,
we suggest you customize a lower video resolution or reduce the frame rate to obtain smooth video.
60 - User's Manual
VIVOTEK
Day/Night Settings (FD8134 only)
Switch to B/W in night mode
Select this to enable the Network Camera to automatically switch to B/W during night mode.
IR cut filter
With a removable IR-cut filter, this Network Camera can automatically remove the filter to let IR light into
the sensor during low light conditions.
■ Auto mode
The Network Camera automatically removes the filter by judging the level of ambient light.
■ Day mode
In day mode, the Network Camera switches on the IR cut filter at all times to block infrared light from
reaching the sensor so that the colors will not be distorted.
■ Night mode
In night mode, the Network Camera switches off the IR cut filter at all times for the sensor to accept
infrared light, thus helping to improve low light sensitivity.
■ Synchronize with digital input
The Network Camera automatically removes the IR cut filter when DI triggers.
■ Schedule mode
The Network Camera switches between day mode and night mode based on a specified schedule.
Enter the start and end time for day mode. Note that the time format is [hh:mm] and is expressed in
24-hour clock time. By default, the start and end time of day mode are set to 07:00 and 18:00.
Light sensor sensitivity
Select Low, Normal, or High sensitivity for the light sensor.
Disable IR LED
If you do not want to use the IR illuminators, you can select this option to turn it off.
User's Manual - 61
VIVOTEK
Motion Detection
This section explains how to configure the Network Camera to enable motion detection. A total
of three motion detection windows can be configured.
2010/03/23 13:44:17
Motion Detection Setting 1:
For normal situations
Follow the steps below to enable motion detection:
Follow the steps below to enable motion detection:
Motion Detection Setting 2:
For special situations
1. Click New to add a new motion detection window.
2. In the Window Name text box, enter a name for the motion detection window.
■ To move and resize the window, drag and drop your mouse on the window.
■ To delete window, click X on the top right corner of the window.
3. Define the sensitivity to moving objects and the space ratio of all alerted pixels by moving the
Sensitivity and Percentage slider bar.
4. Click Save to enable the settings.
5. Select Enable motion detection to enable this function.
For example:
Video(TCP-AV)
2010/03/23 13:44:17
The Percentage Indicator will rise or fall depending on the variation between sequential images. When
motions are detected by the Network Camera and are judged to exceed the defined threshold, the
red bar rises. Meanwhile, the motion detection window will be outlined in red. Photos or videos can be
captured instantly and configured to be sent to a remote server (Email, FTP) by utilizing this feature as a
trigger source. For more information on how to set an event, please refer to Application on page 69.
62 - User's Manual
VIVOTEK
A green bar indicates that even though motions have been detected, the event has not been triggered
because the image variations still fall under the defined threshold.
Percentage = 30%
If you want to configure other motion detection settings for day/night/schedule mode, please click Profile
to open the Motion Detection Profile Settings page as shown below. A total of three motion detection
windows can be configured on this page as well.
Video(TCP-AV)
2010/03/23 13:44:17
Please follow the steps below to set up a profile:
1. Create a new motion detection window.
2. Check Enable this profile.
3. Select the applicable mode: Day mode, Night mode, or Schedule mode. Please manually enter a time
range if you choose Schedule mode.
4. Click Save to enable the settings and click Close to exit the page.
This motion detection window will also be displayed on the Event Settings page. You can go to
Application > Event Settings > Trigger to choose it as a trigger source. Please refer to page 71 for
detailed information.
User's Manual - 63
VIVOTEK
NOTE
► How does motion detection work?
A
C
B
D
There are two motion detection parameters: Sensitivity and Percentage. In the illustration above,
frame A and frame B are two sequential images. Pixel differences between the two frames are
detected and highlighted in gray (frame C) and will be compared with the sensitivity setting. Sensitivity
is a value that expresses the sensitivity to moving objects. Higher sensitivity settings are expected to
detect slight movements while smaller sensitivity settings will neglect them. When the sensitivity is set
to 70%, the Network Camera defines the pixels in the purple areas as “alerted pixels” (frame D).
Percentage is a value that expresses the proportion of “alerted pixels” to all pixels in the motion
detection window. In this case, 50% of pixels are identified as “alerted pixels”. When the percentage is
set to 30%, the motions are judged to exceed the defined threshold; therefore, the motion window will
be outlined in red.
For applications that require a high level of security management, it is suggested to use higher
sensitivity settings and smaller percentage values.
64 - User's Manual
VIVOTEK
Camera Tampering Detection
This section explains how to set up camera temper detection. With tamper detection, the
camera is capable of detecting incidents such as redirection, blocking or defocusing, or even
spray paint.
Please follow the steps below to set up the camera tamper detection function:
1. Check Enable camera tampering detection.
2. Enter the tamper trigger duration. (10 sec. ~ 10 min.) The tamper alarm will be triggered only when the
tampering factor (the difference between current frame and pre-saved background) exceeds the trigger
threshold.
3. Set up the event source as Camera Tampering Detection on Application page > Event Settings /
Server Settings (how to send alarm message) / Media Settings (send what type of alarm
message). Please refer to page 71 for detailed information.
User's Manual - 65
VIVOTEK
Homepage Layout
Advanced Mode
This section explains how to set up your own customized homepage layout.
Preview
This column shows the settings of your hompage layout. You can manually select the background and
font colors in Theme Options (the third column on this page). The settings will be displayed automatically
in this Preview field. The following shows the homepage using the default settings:
■ Hide Powered by VIVOTEK: If you check this item, it will be removed from the homepage.
Logo
Here you can change the logo at the top of your homepage.
Follow the steps below to upload a new logo:
1. Click Custom and the Browse field will appear.
2. Select a logo from your files.
3. Click Upload to replace the existing logo with a new one.
4. Enter a website link if necessary.
5. Click Save to enable the settings.
66 - User's Manual
VIVOTEK
Theme Options
Here you can change the color of your homepage layout. There are three types of preset patterns for you
to choose from. The new layout will simultaneously appear in the Preview filed. Click Save to enable the
settings.
Preset Patterns
Font Color of the Video
Title
Font Color
Background Color of the
Control Area
Font Color of the Configuration Area
Background Color of the
Configuration Area
Background Color of the
Video Area
Frame Color
User's Manual - 67
VIVOTEK
■ Follow the steps below to set up the customed homepage:
1. Click Custom on the left column.
2. Click the field where you want to change the color on the right column.
Color Selector
Custom
Pattern
3. The palette window will pop up as shown below.
2
3
1
4
4. Drag the slider bar and click on the left square to select a desired color.
5. The selected color will be displayed in the corresponding fields and in the Preview column.
6. Click Save to enable the settings.
68 - User's Manual
VIVOTEK
Application
Advanced Mode
This section explains how to configure the Network Camera to responds to particular situations
(event). A typical application is that when a motion is detected, the Network Camera sends
buffered images to an FTP server or e-mail address as notifications.
In the illustration on the right, an event can be
Action
triggered by many sources, such as motion detection Event Trigger
or external digital input devices. When an event is ex. Motion Detection,
Digital Input,
triggered, you can specify what type of action that will System Reboot
be performed. You can configure the Network Camera
Media
Server
(what to send)
(where to send)
to send snapshots or videos to your email address or
ex. Snapshot, Video Clips,
ex. Email, FTP, HTTP Server,
System Log, Digital Output
FTP site.
Network Storage
Customized Script
This function allows you to upload a sample script (.xml file) to the webpage, which will save your time on
configuring the settings. Please note that there is a limited number of customized scripts you can upload;
if the current amount of customized scripts has reached the limit, an alert message will pop up. If you
need more information, please ask for VIVOTEK technical support.
Click to upload a file
Click to modify the
script online
User's Manual - 69
VIVOTEK
Event Settings
In the Event Settings column, click Add to open the Event Settings page. On this page, you can
arrange three elements -- Trigger, Schedule, and Action to set an event. A total of 3 event settings can be
configured.
Event name: Enter a name for the event setting.
Enable this event: Select this option to enable the event setting.
Priority: Select the relative importance of this event (High, Normal, or Low). Events with a higher priority
setting will be executed first.
Detect next event after
motion is detected.
70 - User's Manual
seconds: Enter the duration in seconds to pause motion detection after a
VIVOTEK
An event is an action initiated by a user-defined trigger source; it is the causal arrangement of the
following three elements: Trigger, Event Schedule, and Action.
Trigger
This is the cause or stimulus which defines when to trigger the Network Camera. The trigger source can
be configured to use the Network Camera’s built-in motion detection mechanism or external digital input
devices.
There are several choices of trigger sources as shown below. Select the item to display the detailed
configuration options.
■ Video motion detection
This option makes use of the built-in motion detection mechanism as a trigger source. To enable this
function, you need to configure a Motion Detection Window first. For more information, please refer to
Motion Detection on page 62 for details.
■ Periodically
This option allows the Network Camera to trigger periodically for every other defined minute. Up to 999
minutes are allowed.
■ Digital input
This option allows the Network Camera to use an external digital input device or sensor as a trigger
source. Depending on your application, there are many choices of digital input devices on the market
which helps to detect changes in temperature, vibration, sound, and light, etc.
■ System boot
This option triggers the Network Camera when the power to the Network Camera is disconnected.
■ Recording notify
This option allows the Network Camera to trigger when the recording disk is full or when recording
starts to rewrite older data.
User's Manual - 71
VIVOTEK
■ Camera tampering detection
This option allows the Network Camera to trigger when the camera detects that is is being tampered
with. To enable this function, you need to configure the Tampering Detection option first. Please refer
to page 65 for detailed information.
Event Schedule
Specify the period for the event.
■ Select the days of the week.
■ Select the recording schedule in 24-hr time format.
Action
Define the actions to be performed by the Network Camera when a trigger is activated.
To set an event with recorded video or snapshots, it is necessary to configure the server and
media settings so that the Network Camera will know what action to take (such as which server
to send the media files to) when a trigger is activated.
■ Add Server / Add Media
Click Add Server to configure Server Settings. For more information, please refer to Server Settings
on page 75.
Click Add Media to configure Media Settings. For more information, please refer to Media Settings on
page 78.
72 - User's Manual
VIVOTEK
Here is an example of the Event Settings page:
When completed, click Save to enable the settings and click Close to exit Event Settings page. The new
event settings / server settings / media settings will appear in the event drop-down list on the Application
page.
User's Manual - 73
VIVOTEK
Here is an example of the Application page with an event setting:
When the Event Status is ON, once an event is triggered by motion detection, the Network Camera will
automatically send snapshots via e-mail.
If you want to stop the event trigger, you can click ON to turn it to OFF status or click Delete to remove
the event setting.
To remove a server setting from the list, select a server name from the drop-down list and click Delete.
Note that only when the server setting is not being applied to an event setting can it be deleted.
To remove a media setting from the list, select a media name from the drop-down list and click Delete.
Note that only when the media setting is not being applied to an event setting can it be deleted.
74 - User's Manual
VIVOTEK
Server Settings
Click Add Server on Event Settings page to open the Server Setting page. On this page, you can specify
where the notification messages are sent when a trigger is activated. A total of 5 server settings can be
configured.
Server name: Enter a name for the server setting.
Server Type
There are four choices of server types available: Email, FTP, HTTP, and Network storage. Select the item
to display the detailed configuration options. You can configure either one or all of them.
Email: Select to send the media files via email when a trigger is activated.
■ Sender email address: Enter the email address of the sender.
■ Recipient email address: Enter the email address of the recipient.
■ Server address: Enter the domain name or IP address of the email server.
■ User name: Enter the user name of the email account if necessary.
■ Password: Enter the password of the email account if necessary.
■ Server port: The default mail server port is set to 25. You can also manually set another port.
If your SMTP server requires a secure connection (SSL), check This server requires a secure
connection (SSL).
To verify if the email settings are correctly configured, click Test. The result will be shown in a pop-up
window. If successful, you will also receive an email indicating the result.
Click Save to enable the settings, then click Close to exit the page.
User's Manual - 75
VIVOTEK
FTP: Select to send the media files to an FTP server when a trigger is activated.
■ Server address: Enter the domain name or IP address of the FTP server.
■ Server port
By default, the FTP server port is set to 21. It can also be assigned to another port number between
1025 and 65535.
■ User name: Enter the login name of the FTP account.
■ Password: Enter the password of the FTP account.
■ FTP folder name
Enter the folder where the media file will be placed. If the folder name does not exist, the Network
Camera will create one on the FTP server.
■ Passive mode
Most firewalls do not accept new connections initiated from external requests. If the FTP server
supports passive mode, select this option to enable passive mode FTP and allow data transmission to
pass through the firewall.
To verify if the FTP settings are correctly configured, click Test. The result will be shown in a pop-up
window as shown below. If successful, you will also receive a test.txt file on the FTP server.
Click Save to enable the settings, then click Close to exit the page.
76 - User's Manual
VIVOTEK
HTTP: Select to send the media files to an HTTP server when a trigger is activated.
■ URL: Enter the URL of the HTTP server.
■ User name: Enter the user name if necessary.
■ Password: Enter the password if necessary.
To verify if the HTTP settings are correctly configured, click Test. The result will be shown in a pop-up
window as below. If successful, you will receive a test.txt file on the HTTP server.
Click Save to enable the settings, then click Close to exit the page.
Network storage: Select to send the media files to a network storage location when a trigger is activated.
Please refer to Network Storage Setting on page 82 for details.
Click Save to enable the settings, then click Close to exit the page.
When completed, the new server settings will automatically be displayed on the Event Settings page.
For example:
User's Manual - 77
VIVOTEK
Media Settings
Click Add Media on the Event Settings page to open the Media Settings page. On this page, you can
specify the type of media that will be sent when a trigger is activated. A total of 5 media settings can be
configured.
Media name: Enter a name for the media setting.
Media Type
There are three choices of media types available: Snapshot, Video Clip, and System log. Select the item
to display the detailed configuration options. You can configure either one or all of them.
Snapshot: Select to send snapshots when a trigger is activated.
■ Source: Select to take snapshots from stream 1 ~ 4.
■ Send pre-event images
The Network Camera has a buffer area; it temporarily holds data up to a certain limit. Enter a number
to decide how many images to capture before a trigger is activated. Up to 7 images can be generated.
■ Send post-event images
Enter a number to decide how many images to capture after a trigger is activated. Up to 7 images can
be generated.
For example, if both the Send pre-event images and Send post-event images are set to 7, a total of 15
images are generated after a trigger is activated.
1 pic.
2 pic.
3 pic.
4 pic.
5 pic.
6 pic.
7 pic.
8 pic.
9 pic.
10 pic.
11 pic. 10 pic.
12 pic. 13 pic.
Trigger Activation
■ File name prefix
Enter the text that will be appended to the front of the file name.
■ Add date and time suffix to the file name
Select this option to add a date/time suffix to the file name.
For example:
Snapshot_20100323_100341
File name prefix Date and time suffix
The format is: YYYYMMDD_HHMMSS
Click Save to enable the settings, then click Close to exit the page.
78 - User's Manual
14 pic.
15 pic.
VIVOTEK
Video clip: Select to send video clips when a trigger is activated.
■ Source: Select a source of video clip.
■ Pre-event recording
The Network Camera has a buffer area; it temporarily holds data up to a certain limit. Enter a number
to decide the duration of recording before a trigger is activated. Up to 9 seconds can be set.
■ Maximum duration
Specify the maximum recording duration in seconds. Up to 20 seconds can be set.
For example, if pre-event recording is set to 5 seconds and the maximum duration is set to 10
seconds, the Network Camera continues to record for another 4 seconds after a trigger is activated.
1 sec.
2 sec.
3 sec.
4 sec.
5 sec.
6 sec.
7 sec.
8 sec.
9 sec.
10 sec.
Trigger Activation
■ Maximum file size
Specify the maximum file size allowed.
■ File name prefix
Enter the text that will be appended to the front of the file name.
For example:
Video Clip_20100323_100341
File name prefix Date and time suffix
The format is: YYYYMMDD_HHMMSS
Click Save to enable the settings, then click Close to exit the page.
System log: Select to send a system log when a trigger is activated.
Click Save to enable the settings, then click Close to exit the page.
When completed, click Save to enable the settings and click Close to exit this page. The new media
settings will appear on the Event Settings page.
User's Manual - 79
VIVOTEK
You can continue to select a server and media type for the event. Please go back to page 66 for detailed
information.
■ SD Test: Click to test your SD card. The system will display a message indicating success or failure. If
you want to use your SD card for on board storage, please format it before use. Please refer to page
82 for detailed information.
■ Create folders by date, time, and hour automatically: If you check this item, the system will generate
folders automatically by date.
■ View: Click this button to open a file list window. This function is only for SD card and Network
Storage.
If you click View button of SD card, a Local storage page will pop up for you to manage recorded files
on SD card. For more information about Local storage, please refer to page 85 for illustration.
If you click View button of Network storage, a file directory window will pop up for you to view
recorded data on Network storage. For detailed illustration, please refer to the next page.
80 - User's Manual
VIVOTEK
The following is an example of a file destination with video clips:
The format is: YYYYMMDD
Click to open the directory
20100323
20100324
20100325
Click to delete all recorded data
Click to delete selected items
Click 20100323 to open the directory:
The format is: HH (24r)
Click to open the file list for that hour
Video Clip_58.mp4
2010/03/23
Video Clip_59.mp4
2010/03/23
Click to go back to the previous
level of the directory
Click to delete
selected items
Click to delete all
recorded data
Video Clip_58.mp4
2010/03/23
Video Clip_59.mp4
2010/03/23
The format is: File name prefix + Minute (mm)
You can set up the file name prefix on Media Settings (Video Clip) page.
Please refer to page 78 for detailed information.
User's Manual - 81
VIVOTEK
Recording
Advanced Mode
This section explains how to configure the recording settings for the Network Camera.
Recording Settings
Insert your SD card and click here to test
NOTE
► Before setting up this page, please set up the Network Storage on the Server Settings page first.
► Please remember to format your SD card when using for the first time. Please refer to page 85 for
detailed information.
Network Storage Setting
Click Server to open the Server Settings page and follow the steps below to set up:
1. Fill in the information for your server.
For example:
3
Network storage path
(\\server name or IP address\folder name)
1
2
4
User name and password for your server
2. Click Test to check the setting. The result will be shown in the pop-up window.
82 - User's Manual
VIVOTEK
If successful, you will receive a test.txt file on the network storage server.
3. Enter a server name.
4. Click Save to complete the settings and click Close to exit the page.
Recording Settings
Click Add to open the recording setting page. On this page, you can define the adaptive recording,
recording source, recording schedule, and recording capacity. A total of 2 recording settings can be
configured.
Recording name: Enter a name for the recording setting.
Enable this recording: Select this option to enable video recording.
With adaptive recording: Select this option will activate the frame rate control according to alarm trigger.
The frame control means that when there is alarm trigger, the frame rate will raise up to the value you’ve
set on Video page. Please refer to page 52 for more informaiton.
If you enable adaptive recording and enable time-shift cache stream on Camera A, only when an event
is triggered on Camera A will the server record the full frame rate streaming data; otherwise, it will only
request the I frame data during normal monitoring, thus effectively save lots of bandwidths and storage.
When there is no alarm trigger:
- JEPE mode: record 1 frame per second.
- H.264 mode: record I frame only.
- MPEG-4 mode: record I frame only.
Bandwidth
When the I frame period is >1s on Video settings
page, it should force to make the I frame period to
1s when adaptive recording is activated.
I frame ---> Full frame rate ---> I frame
Bandwidth
Activity Adaptive Streaming
for Dynamic Frame Rate Control
Continuous recording
Time
User's Manual - 83
VIVOTEK
The alarm trigger includes: motion detection, PIR detection, tampering detection, DI detection, IVA
detection, temperature detection, video loss, and network loss. Please refer to Event Settings on page 70.
■ Pre-event recording and post-event recording
The Network Camera has a buffer area; it temporarily holds data up to a certain limit. Enter a number
to decide the duration of recording before and after a trigger is activated.
NOTE
► To enable adaptive recording, please also enable time shift caching stream and select a caching
stream on Video page. Please refer to page 52 for detailed instrction.
Priority: Select the relative importance of this recording setting (High, Normal, and Low).
Source: Select the recording source (stream 1 ~ 4).
Trigger: Select a trigger source.
■ Schedule: The server will start to record files on the local storage or network storage (NAS).
■ Network fail: Since network fail, the server will start to record files on the local storage (SD card).
Recording Schedule: Specify the recording duration.
■ Select the days of the week.
■ Select the recording start and end times in 24-hr time format.
84 - User's Manual
VIVOTEK
Destination: You can select the SD card or network storage that was set up for the recorded video files.
Capacity: You can choose either the entire free space available or limit the reserved space. The
recording size limit must be larger than the reserved amount for cyclic recording.
File name prefix: Enter the text that will be appended to the front of the file name.
Enable cyclic recording: If you check this item, when the maximum capacity is reached, the oldest file
will be overwritten by the latest one. The reserved amount is reserved for cyclic recording to prevent
malfunction. This value must be larger than 15 MBytes.
If you want to enable recording notification, please click Application to set up. Please refer to Trigger >
Recording notify on page 72 for detailed information.
When completed, select Enable this recording. Click Save to enable the setting and click Close to exit
this page. When the system begins recording, it will send the recorded files to the Network Storage.
The new recording name will appear in the drop-down list on the recording page as shown below.
To remove a recording setting from the list, select a recording name from the drop-down list and click
Delete.
■ Click Video (Name): Opens the Recording Settings page to modify.
■ Click ON (Status): The Status will become OFF and stop recording.
■ Click NAS (Destination): Opens the file list of recordings as shown below. For more information about
folder naming rules, please refer to page 81 for details.
20100323
20100324
20100325
User's Manual - 85
VIVOTEK
Local Storage
Advanced Mode
This section explains how to manage the SD card for on board storage. Here you can view SD
card status, search for recorded files to playback, download, etc.
no SD card
SD Card Management
SD card status: This column shows the status and reserved space of your SD card. Please remember to
format the SD card when using for the first time.
86 - User's Manual
VIVOTEK
SD card control
■ Enable cyclic storage: Check this item if you want to enable cyclic recording. When the maximum
capacity is reached, the oldest file will be overwritten by the latest one.
■ Enable automatic disk cleanup: Check this item and enter the number of days you wish to retain a file.
For example, if you enter “7 days”, the recorded files will be stored on the SD card for 7 days.
Click Save to enable your settings.
Searching and Viewing the Records
This column allows the user to set up search criteria for recorded data. If you do not select any criteria
and click Search button, all recorded data will be listed in the Search Results cloumn.
File attributes: Select one or more items as your search criteria.
Trigger time: Manually enter the time range you want to search.
Click Search and the recorded data corresponding to the search criteria will be listed in Search Results
window.
User's Manual - 87
VIVOTEK
Search Results
The following is an example of search results. There are four columns: Trigger time, Media type, Trigger
type, and Locked. Click
to sort the search results in either direction.
Enter a key word to filter the
Numbers of entries displayed on one page
search results
Highlight an
item
Click to switch
pages
View: Click on a search result which will highlight the selected item in purple as shown above. Click the
View button and a media window will pop up to play back the selected file.
For example:
2010/03/23 13:44:17
Click to adjust the image size
88 - User's Manual
VIVOTEK
Download: Click on a search result to highlight the selected item in purple as shown above. Then click
the Download button and a file download window will pop up for you to save the file.
JPEGs to AVI: This functions only applies to “JPEG“ format files such as snapshots. You can select
several snapshots from the list, then click this button. Those snapshots will be converted into an AVI file.
Lock/Unlock: Select the desired search results, then click this button. The selected items will become
Locked, which will not be deleted during cyclic recoroding. You can click again to unlock the selections.
For example:
Remove: Select the desired search results, then click this button to delete the files.
User's Manual - 89
VIVOTEK
System Log
Advanced Mode
This section explains how to configure the Network Camera to send the system log to the
remote server as backup.
Remote Log
You can configure the Network Camera to send the system log file to a remote server as a log backup.
Before utilizing this feature, it is suggested that the user install a log-recording tool to receive system log
messages from the Network Camera. An example is Kiwi Syslog Daemon. Visit http://www.kiwisyslog.
com/kiwi-syslog-daemon-overview/.
Follow the steps below to set up the remote log:
1. In the IP address text box, enter the IP address of the remote server.
2. In the port text box, enter the port number of the remote server.
3. When completed, select Enable remote log and click Save to enable the setting.
Current Log
This column displays the system log in chronological order. The system log is stored in the Network
Camera’s buffer area and will be overwritten when reaching a certain limit.
90 - User's Manual
VIVOTEK
View Parameters
Advanced Mode
The View Parameters page lists the entire system’s parameters in alphabetical order. If you
need technical assistance, please provide the information listed on this page.
User's Manual - 91
VIVOTEK
Maintenance
This chapter explains how to restore the Network Camera to factory default, upgrade firmware
version, etc.
Reboot
This feature allows you to reboot the Network Camera, which takes about one minute to complete. When
completed, the live video page will be displayed in your browser. The following message will be displayed
during the reboot process.
If the connection fails after rebooting, manually enter the IP address of the Network Camera in the
address field to resume the connection.
Restore
This feature allows you to restore the Network Camera to factory default settings.
Network Type: Select this option to retain the Network Type settings (please refer to Network Type on
page 33).
Daylight Saving Time: Select this option to retain the Daylight Saving Time settings (please refer to
System on page 24)
Custom Language: Select this option to retain the Custom Language settings.
If none of the options is selected, all settings will be restored to factory default.
The following message is displayed during the restoring process.
92 - User's Manual
VIVOTEK
Export / Upload Files Advanced Mode
This feature allows you to Export / Upload daylight saving time rules, custom language files, and setting
backup files.
Export daylight saving time configuration file: Click to set the start and end time of DST.
Follow the steps below to export:
1. In the Export files column, click Export to export the daylight saving time configuration file from the
Network Camera.
2. A file download dialog will pop up as shown below. Click Open to review the XML file or click Save to
store the file for editing.
3. Open the file with Microsoft® Notepad and locate your time zone; set the start and end time of DST.
When completed, save the file.
In the example below, DST begins each year at 2:00 a.m. on the second Sunday in March and ends at
2:00 a.m. on the first Sunday in November.
User's Manual - 93
VIVOTEK
Upload daylight saving time rule: Click Browse… and specify the XML file to upload.
If the incorrect date and time are assigned, you will see the following warning message when uploading
the file to the Network Camera.
The following message is displayed when attempting to upload an incorrect file format.
Export language file: Click to export language strings. VIVOTEK provides nine languages: English,
Deutsch, Español, Français, Italiano, 日本語, Português, 簡体中文, and 繁體中文.
Upload custom language file: Click Browse… and specify your own custom language file to upload.
Export setting backup file: Click to export all parameters for the device and user-defined scripts.
Upload setting backup file: Click Browse… to upload a setting backup file. Please note that the model
and firmware version of the device should be the same as the setting backup file. If you have set up a
fixed IP or other special settings for your device, it is not suggested to upload a settings backup file.
Upgrade Firmware
This feature allows you to upgrade the firmware of your Network Camera. It takes a few minutes to
complete the process.
Note: Do not power off the Network Camera during the upgrade!
Follow the steps below to upgrade the firmware:
1. Download the latest firmware file from the VIVOTEK website. The file is in .pkg file format.
2. Click Browse… and specify the firmware file.
3. Click Upgrade. The Network Camera starts to upgrade and will reboot automatically when the upgrade
completes.
If the upgrade is successful, you will see “Reboot system now!! This connection will close”. After that, reaccess the Network Camera.
94 - User's Manual
VIVOTEK
The following message is displayed when the upgrade has succeeded.
Reboot system now!!
This connection will close.
The following message is displayed when you have selected an incorrect firmware file.
Starting firmware upgrade...
Do not power down the server during the upgrade.
The server will restart automatically after the upgrade is
completed.
This will take about 1 - 5 minutes.
Wrong PKG file format
Unpack fail
User's Manual - 95
VIVOTEK
Appendix
URL Commands for the Network Camera
1. Overview
For some customers who already have their own web site or web control application, the Network
Camera/Video Server can be easily integrated through URL syntax. This section specifies the external
HTTP-based application programming interface. The HTTP-based camera interface provides the
functionality to request a single image, control camera functions (PTZ, output relay etc.), and get and set
internal parameter values. The image and CGI-requests are handled by the built-in Web server.
2. Style Convention
In URL syntax and in descriptions of CGI parameters, text within angle brackets denotes content that
is to be replaced with either a value or a string. When replacing the text string, the angle brackets
should also be replaced. An example of this is the description of the name for the server, denoted with
<servername> in the URL syntax description below, that is replaced with the string myserver in the URL
syntax example further down in the page.
URL syntax is denoted with the word "Syntax:" written in bold face followed by a box with the referenced
syntax as shown below. For example, name of the server is written as <servername> and is intended to
be replaced with the name of the actual server. This can either be a name, e.g., "mywebcam" or "thecam.
adomain.net" or the associated IP number for the server, e.g., 192.168.0.220.
Syntax:
http://<servername>/cgi-bin/viewer/video.jpg
Description of returned data is written with "Return:" in bold face followed by the returned data in a box. All data is
returned in HTTP format, i.e., each line is separated with a Carriage Return and Line Feed (CRLF) printed as \r\n.
Return:
HTTP/1.0 <HTTP code> <HTTP text>\r\n
URL syntax examples are written with "Example:" in bold face followed by a short description and a light grey box
with the example.
Example: request a single snapshot image
http://mywebserver/cgi-bin/viewer/video.jpg
96 - User's Manual
VIVOTEK
3. General CGI URL Syntax and Parameters
When the CGI request includes internal camera parameters, these parameters must be written exactly as
they are named in the camera or video server. The CGIs are organized in functionally-related directories
under the cgi-bin directory. The file extension .cgi is required.
Syntax:
http://<servername>/cgi-bin/<subdir>[/<subdir>...]/<cgi>.<ext>
[?<parameter>=<value>[&<parameter>=<value>...]]
Example: Set digital output #1 to active
http://mywebserver/cgi-bin/dido/setdo.cgi?do1=1
User's Manual - 97
VIVOTEK
4. Security Level
SECURITY LEVEL
SUB-DIRECTORY
DESCRIPTION
0
anonymous
Unprotected.
1 [view]
anonymous, viewer,
1. Can view, listen, talk to camera.
dido, camctrl
2. Can control DI/DO, PTZ of the camera.
anonymous, viewer,
Operator access rights can modify most of the camera’s
dido, camctrl, operator
parameters except some privileges and network options.
anonymous, viewer,
Administrator access rights can fully control the camera’s
dido, camctrl, operator,
operations.
4 [operator]
6 [admin]
admin
7
N/A
Internal parameters. Unable to be changed by any external
interfaces.
98 - User's Manual
VIVOTEK
5. Get Server Parameter Values
Note: The access right depends on the URL directory.
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/anonymous/getparam.cgi?[<parameter>]
[&<parameter>…]
http://<servername>/cgi-bin/viewer/getparam.cgi?[<parameter>]
[&<parameter>…]
http://<servername>/cgi-bin/operator/getparam.cgi?[<parameter>]
[&<parameter>…]
http://<servername>/cgi-bin/admin/getparam.cgi?[<parameter>]
[&<parameter>…]
Where the <parameter> should be <group>[_<name>]. If you do not specify any parameters, all the
parameters on the server will be returned. If you specify only <group>, the parameters of the related group
will be returned.
When querying parameter values, the current parameter values are returned.
A successful control request returns parameter pairs as follows:
Return:
HTTP/1.0 200 OK\r\n
Content-Type: text/html\r\n
Context-Length: <length>\r\n
\r\n
<parameter pair>
where <parameter pair> is
<parameter>=<value>\r\n
[<parameter pair>]
<length> is the actual length of content.
Example: Request IP address and its response
Request:
http://192.168.0.123/cgi-bin/admin/getparam.cgi?network_ipaddress
User's Manual - 99
VIVOTEK
Response:
HTTP/1.0 200 OK\r\n
Content-Type: text/html\r\n
Context-Length: 33\r\n
\r\n
network_ipaddress=192.168.0.123\r\n
100 - User's Manual
VIVOTEK
6. Set Server Parameter Values
Note: The access right depends on the URL directory.
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/anonymous/setparam.cgi? <parameter>=<value>
[&<parameter>=<value>…][&return=<return page>]
http://<servername>/cgi-bin/viewer/setparam.cgi? <parameter>=<value>
[&<parameter>=<value>…][&return=<return page>]
http://<servername>/cgi-bin/operator/setparam.cgi? <parameter>=<value>
[&<parameter>=<value>…][&return=<return page>]
http://<servername>/cgi-bin/admin/setparam.cgi? <parameter>=<value>
[&<parameter>=<value>…][&return=<return page>]
PARAMETER
VALUE
DESCRIPTION
<group>_<name> value to assigned
Assign <value> to the parameter <group>_<name>.
return
Redirect to the page <return page> after the parameter is
<return page>
assigned. The <return page> can be a full URL path or relative
path according to the current path. If you omit this parameter, it
will redirect to an empty page.
(Note: The return page can be a general HTML file (.htm, .html).
It cannot be a CGI command or have any extra parameters. This
parameter must be placed at the end of the parameter list
Return:
HTTP/1.0 200 OK\r\n
Content-Type: text/html\r\n
Context-Length: <length>\r\n
\r\n
<parameter pair>
where <parameter pair> is
<parameter>=<value>\r\n
[<parameter pair>]
Only the parameters that you set and are readable will be returned.
User's Manual - 101
VIVOTEK
Example: Set the IP address of server to 192.168.0.123:
Request:
http://myserver/cgi-bin/admin/setparam.cgi?network_ipaddress=192.168.0.123
Response:
HTTP/1.0 200 OK\r\n
Content-Type: text/html\r\n
Context-Length: 33\r\n
\r\n
network_ipaddress=192.168.0.123\r\n
102 - User's Manual
VIVOTEK
7. Available Parameters on the Server
This chapter defines all the parameters which can be configured or retrieved from VIVOTEK network camera
or video server. The general format of description is listed in the table below
Valid values:
VALID VALUES
DESCRIPTION
string[<n>]
Text strings shorter than ‘n’ characters. The characters “,’, <,>,& are invalid.
string[n~m]
Text strings longer than `n’ characters and shorter than `m’ characters. The
characters “,’, <,>,& are invalid.
password[<n>]
The same as string but displays ‘*’ instead.
integer
Any number between (-231 – 1) and (231 – 1).
positive integer
Any number between 0 and (232 – 1).
<m> ~ <n>
Any number between ‘m’ and ‘n’.
domain name[<n>]
A string limited to a domain name shorter than ‘n’ characters (eg.
www.ibm.com).
email address [<n>]
A string limited to an email address shorter than ‘n’ characters (eg.
[email protected]).
ip address
A string limited to an IP address (eg. 192.168.1.1).
mac address
A string limited to contain a MAC address without hyphens or colons.
boolean
A boolean value of 1 or 0 represents [Yes or No], [True or False], [Enable or
Disable].
<value1>,
Enumeration. Only given values are valid.
<value2>,
<value3>,
…
blank
A blank string.
everything inside <>
A description
integer primary key
SQLite data type. A 32-bit signed integer. The value is assigned a unique
integer by the server.
text
SQLite data type. The value is a text string, stored using the database
encoding (UTF-8, UTF-16BE or UTF-16-LE).
coordinate
x, y coordinate (eg. 0,0)
window size
window width and height (eg. 800x600)
NOTE: The camera should not be restarted when parameters are changed.
User's Manual - 103
VIVOTEK
7.1 System
Group: system
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
hostname
string[40]
1/6
Host name of server
(Network Camera,
Wireless Network Camera,
Video Server,
Wireless Video Server).
date
time
datetime
<yyyy/mm/dd>,
6/6
Current date of system. Set to ‘keep’ to keep
keep,
date unchanged. Set to ‘auto’ to use NTP to
auto
synchronize date.
<hh:mm:ss>,
6/6
Current time of the system. Set to ‘keep’ to
keep,
keep time unchanged. Set to ‘auto’ to use NTP
auto
to synchronize time.
<MMDDhhmmYYYY
6/6
Another current time format of the system.
6/6
NTP server.
.ss>
ntp
timezoneindex
<domain name>,
<ip address>,
*Do not use “skip to invoke default server” for
<blank>
default value.
-489 ~ 529
6/6
Indicate timezone and area.
-480: GMT-12:00 Eniwetok, Kwajalein
-440: GMT-11:00 Midway Island, Samoa
-400: GMT-10:00 Hawaii
-360: GMT-09:00 Alaska
-320: GMT-08:00 Las Vegas, San_Francisco,
Vancouver
-280: GMT-07:00 Mountain Time, Denver
-281: GMT-07:00 Arizona
-240: GMT-06:00 Central America, Central
Time, Mexico City, Saskatchewan
-200: GMT-05:00 Eastern Time, New York,
Toronto
-201: GMT-05:00 Bogota, Lima, Quito, Indiana
-180: GMT-04:30 Caracas
-160: GMT-04:00 Atlantic Time, Canada, La
Paz, Santiago
-140: GMT-03:30 Newfoundland
104 - User's Manual
VIVOTEK
-120: GMT-03:00 Brasilia, Buenos Aires,
Georgetown, Greenland
-80: GMT-02:00 Mid-Atlantic
-40: GMT-01:00 Azores, Cape_Verde_IS.
0: GMT Casablanca, Greenwich Mean Time:
Dublin, Edinburgh, Lisbon, London
40: GMT 01:00 Amsterdam, Berlin, Rome,
Stockholm, Vienna, Madrid, Paris
41: GMT 01:00 Warsaw, Budapest, Bern
80: GMT 02:00 Athens, Helsinki, Istanbul, Riga
81: GMT 02:00 Cairo
82: GMT 02:00 Lebanon, Minsk
83: GMT 02:00 Israel
120: GMT 03:00 Baghdad, Kuwait, Riyadh,
Moscow, St. Petersburg, Nairobi
121: GMT 03:00 Iraq
140: GMT 03:30 Tehran
160: GMT 04:00 Abu Dhabi, Muscat, Baku,
Tbilisi, Yerevan
180: GMT 04:30 Kabul
200: GMT 05:00 Ekaterinburg, Islamabad,
Karachi, Tashkent
220: GMT 05:30 Calcutta, Chennai, Mumbai,
New Delhi
230: GMT 05:45 Kathmandu
240: GMT 06:00 Almaty, Novosibirsk, Astana,
Dhaka, Sri Jayawardenepura
260: GMT 06:30 Rangoon
280: GMT 07:00 Bangkok, Hanoi, Jakarta,
Krasnoyarsk
320: GMT 08:00 Beijing, Chongging, Hong
Kong, Kuala Lumpur, Singapore, Taipei
360: GMT 09:00 Osaka, Sapporo, Tokyo, Seoul,
Yakutsk
380: GMT 09:30 Adelaide, Darwin
400: GMT 10:00 Brisbane, Canberra,
Melbourne, Sydney, Guam, Vladivostok
440: GMT 11:00 Magadan, Solomon Is., New
Caledonia
User's Manual - 105
VIVOTEK
480: GMT 12:00 Aucklan, Wellington, Fiji,
Kamchatka, Marshall Is.
520: GMT 13:00 Nuku'Alofa
daylight_enable
<boolean>
6/6
Enable automatic daylight saving time in time
zone.
daylight_dstactualm
<boolean>
6/7
ode
Check if current time is under daylight saving
time.
(Used internally)
daylight_auto_begin
string[19]
6/7
time
daylight_auto_endti
(product dependent)
string[19]
6/7
me
daylight_manual_off
Display the current daylight saving start time.
Display the current daylight saving end time.
(product dependent)
<integer>
6/6
Manually set daylight saving time with offset.
string[19]
6/6
Manually set daylight saving time beginning.
string[19]
6/6
Manually set daylight saving time end.
string
6/6
List time zone index which support daylight
set
daylight_manual_be
gintime
daylight_manual_en
dtime
daylight_timezones
saving time.
updateinterval
0,
6/6
0 to Disable automatic time adjustment,
3600,
otherwise, it indicates the seconds between NTP
86400,
automatic update intervals.
604800,
2592000
restore
0,
7/6
<positive integer>
reset
0,
values after <value> seconds.
7/6
<positive integer>
restoreexceptnet
<Any value>
Restore the system parameters to default
Restart the server after <value> seconds if
<value> is non-negative.
7/6
Restore the system parameters to default
values except (ipaddress, subnet, router, dns1,
dns2, pppoe).
This command can cooperate with other
“restoreexceptXYZ” commands. When
cooperating with others, the system parameters
will be restored to the default value except for a
union of the combined results.
restoreexceptdst
<Any value>
7/6
Restore the system parameters to default
values except all daylight saving time settings.
106 - User's Manual
VIVOTEK
This command can cooperate with other
“restoreexceptXYZ” commands. When
cooperating with others, the system parameters
will be restored to default values except for a
union of combined results.
restoreexceptlang
<Any Value>
7/6
Restore the system parameters to default
values except the custom language file the user
has uploaded.
This command can cooperate with other
“restoreexceptXYZ” commands. When
cooperating with others, the system parameters
will be restored to the default value except for a
union of the combined results.
7.1.1 System Info.
Subgroup of system: info (The fields in this group are unchangeable.)
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
modelname
string[40]
0/7
Internal model name of the server (eg. IP7139)
extendedmodelname
string[40]
0/7
ODM specific model name of server (eg.
DCS-5610). If it is not an ODM model, this field
will be equal to “modelname”
serialnumber
<mac
0/7
12 characters MAC address (without hyphens).
0/7
Firmware version, including model, company,
address>
firmwareversion
string[40]
and version number in the format:
<MODEL-BRAND-VERSION>
language_count
<integer>
0/7
Number of webpage languages available on the
server.
language_i<0~(count-1)>
string[16]
0/7
Available language lists.
customlanguage_maxcount
<integer>
0/6
Maximum number of custom languages
supported on the server.
customlanguage_count
<integer>
0/6
Number of custom languages which have been
uploaded to the server.
customlanguage_i<0~(max
string
0/6
Custom language name.
count-1)>
User's Manual - 107
VIVOTEK
7.2 Status
Group: status
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
di_i<0~(ndi-1)>
<boolean>
1/7
0 => Inactive, normal
1 => Active, triggered
onlinenum_rtsp
integer
6/7
Current number of RTSP connections.
onlinenum_httppush
integer
6/7
Current number of HTTP push server connections.
eth_i0
<string>
1/99
Get network information from mii-tool.
7.3 Digital Input Behavior Define
Group: di_i<0~(ndi-1)> (capability.ndi > 0)
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
normalstate
high,
1/1
Indicates open circuit or closed circuit (inactive status)
low
7.4 Security
Group: security
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
user_i0_name
string[64]
6/7
User name of root
user_i<1~20>_name
string[64]
6/7
User name
user_i0_pass
password[64]
6/6
Root password
user_i<1~20>_pass
password[64]
7/6
User password
user_i0_privilege
viewer,
6/7
Root privilege
6/6
User privilege
operator,
admin
user_i<1~20>_
viewer,
privilege
operator,
admin
108 - User's Manual
VIVOTEK
7.5 Network
Group: network
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
type
lan,
6/6
Network connection type.
6/6
1 => Get ipaddress, subnet, router, dns1, dns2 from DHCP
pppoe
resetip
<boolean>
server at next reboot.
0 => Use preset ipaddress, subnet, rounter, dns1, and dns2.
ipaddress
<ip address>
6/6
IP address of server.
subnet
<ip address>
6/6
Subnet mask.
router
<ip address>
6/6
Default gateway.
dns1
<ip address>
6/6
Primary DNS server.
dns2
<ip address>
6/6
Secondary DNS server.
wins1
<ip address>
6/6
Primary WINS server.
wins2
<ip address>
6/6
Secondary WINS server.
7.5.1 802.1x
Subgroup of network: ieee8021x
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
enable
<boolean>
6/6
Enable/disable IEEE 802.1x
eapmethod
eap-peap,
6/6
Selected EAP method
eap-tls
identity_peap
String[64]
6/6
PEAP identity
identity_tls
String[64]
6/6
TLS identity
password
String[254]
6/6
Password for TLS
privatekeypassword
String[254]
6/6
Password for PEAP
ca_exist
<boolean>
6/6
CA installed flag
ca_time
<integer>
6/7
CA installed time. Represented in EPOCH
ca_size
<integer>
6/7
CA file size (in bytes)
certificate_exist
<boolean>
6/6
Certificate installed flag (for TLS)
certificate_time
<integer>
6/7
Certificate installed time. Represented in EPOCH
certificate_size
<integer>
6/7
Certificate file size (in bytes)
privatekey_exist
<boolean>
6/6
Private key installed flag (for TLS)
privatekey_time
<integer>
6/7
Private key installed time. Represented in EPOCH
privatekey_size
<integer>
6/7
Private key file size (in bytes)
User's Manual - 109
VIVOTEK
7.5.2 QoS
Subgroup of network: qos
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
cos_enable
<boolean>
6/6
Enable/disable CoS (IEEE 802.1p)
cos_vlanid
1~4095
6/6
VLAN ID
cos_video
0~7
6/6
Video channel for CoS
cos_eventalarm
0~7
6/6
Event/alarm channel for CoS
cos_management
0~7
6/6
Management channel for CoS
cos_eventtunnel
0~7
6/6
Event/Control channel for CoS
dscp_enable
<boolean>
6/6
Enable/disable DSCP
dscp_video
0~63
6/6
Video channel for DSCP
dscp_eventalarm
0~63
6/6
Event/alarm channel for DSCP
dscp_management
0~63
6/6
Management channel for DSCP
dscp_eventtunnel
0~63
6/6
Event/Control channel for DSCP
7.5.3 IPv6
Subgroup of network: ipv6
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
enable
<boolean>
6/6
Enable IPv6.
addonipaddress
<ip address>
6/6
IPv6 IP address.
addonprefixlen
0~128
6/6
IPv6 prefix length.
addonrouter
<ip address>
6/6
IPv6 router address.
addondns
<ip address>
6/6
IPv6 DNS address.
allowoptional
<boolean>
6/6
Allow manually setup of IP address setting.
SECURITY
DESCRIPTION
7.5.4 FTP
Subgroup of network: ftp
NAME
VALUE
(get/set)
Port
110 - User's Manual
21, 1025~65535
6/6
Local ftp server port.
VIVOTEK
7.5.5 HTTP
Subgroup of network: http
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
port
80, 1025 ~ 65535
6/6
HTTP port.
alternateport
1025~65535
6/6
Alternate HTTP port.
authmode
basic,
1/6
HTTP authentication mode.
1/6
HTTP server push access name for stream 1.
digest
s0_accessname
string[32]
(capability.protocol.spush_mjpeg =1 and
video.stream.count>0)
s1_accessname
string[32]
1/6
HTTP server push access name for stream 2.
(capability.protocol.spush_mjpeg =1 and
video.stream.count>1)
s2_accessname
string[32]
1/6
Http server push access name for stream 3
(capability.protocol.spush_mjpeg =1 and
video.stream.count>2)
s3_accessname
string[32]
1/6
Http server push access name for stream 4
(capability.protocol.spush_mjpeg =1 and
video.stream.count>3)
s4_accessname
string[32]
1/6
Http server push access name for stream 5
(capability.protocol.spush_mjpeg =1 and
video.stream.count>4)
anonymousviewing
<boolean>
1/6
Enable anoymous streaming viewing.
7.5.6 HTTPS Port
Subgroup of network: https_port
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
port
443, 1025 ~ 65535
6/6
HTTPS port.
7.5.7 RTSP
Subgroup of network: rtsp
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
port
554, 1025 ~ 65535
1/6
RTSP port.
User's Manual - 111
VIVOTEK
(capability.protocol.rtsp=1)
anonymousviewing
<boolean>
1/6
Enable anoymous streaming viewing.
authmode
disable,
1/6
RTSP authentication mode.
basic,
(capability.protocol.rtsp=1)
digest
s0_accessname
string[32]
1/6
RTSP access name for stream1.
(capability.protocol.rtsp=1 and
video.stream.count>0)
s1_accessname
string[32]
1/6
RTSP access name for stream2.
(capability.protocol.rtsp=1 and
video.stream.count>1)
s2_accessname
string[32]
1/6
RTSP access name for stream3
(capability.protocol.rtsp=1 and
video.stream.count>2)
s3_accessname
string[32]
1/6
RTSP access name for stream4
(capability.protocol.rtsp=1 and
video.stream.count>3)
S4_accessname
string[32]
1/6
RTSP access name for stream5
(capability.protocol.rtsp=1 and
video.stream.count>4)
7.5.7.1 RTSP Multicast
Subgroup of network_rtsp_s<0~(n-1)>: multicast, n is stream count
(capability.protocol.rtp.multicast=1)
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
alwaysmulticast
<boolean>
4/4
Enable always multicast.
ipaddress
<ip address>
4/4
Multicast IP address.
videoport
1025 ~ 65535
4/4
Multicast video port.
ttl
1 ~ 255
4/4
Multicast time to live value.
7.5.8 SIP Port
Subgroup of network: sip
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
Port
112 - User's Manual
1025 ~ 65535
1/6
SIP port. (capability.protocol.sip=1)
VIVOTEK
7.5.9 RTP Port
Subgroup of network: rtp
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
videoport
1025 ~ 65535
6/6
Video channel port for RTP.
(capability.protocol.rtp_unicast=1)
7.5.10 PPPoE
Subgroup of network: pppoe
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
user
string[128]
6/6
PPPoE account user name.
pass
password[64]
6/6
PPPoE account password.
7.6 IP Filter
Group: ipfilter
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
enable
<boolean>
6/6
Enable access list filtering.
admin_enable
<boolean>
6/6
Enable administrator IP address.
admin_ip
String[44]
6/6
Administrator IP address.
maxconnection
1~10
6/6
Maximum number of concurrent streaming
connection(s).
allow_i<0~9>_start
1.0.0.0 ~
6/6
Allowed starting IPv4 address for connection.
6/6
Allowed ending IPv4 address for connection.
6/6
Denied starting IPv4 address for connection.
6/6
Denied ending IPv4 address for connection.
255.255.255.255
allow_i<0~9>_end
1.0.0.0 ~
255.255.255.255
deny_i<0~9>_start
1.0.0.0 ~
255.255.255.255
deny_i<0~9>_end
1.0.0.0 ~
255.255.255.255
ipv6_allow_i<0~9>
String[44]
6/6
Allowed IPv6 address for connection.
ipv6_deny_i<0~9>
String[44]
6/6
Denied IPv6 address for connection.
User's Manual - 113
VIVOTEK
7.7 Video Input
7.7.1 Video Input Setting per Channel
Group: videoin_c<0~(n-1)> for n channel products, and m is stream number
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
cmosfreq
50, 60
4/4
CMOS frequency.
(videoin.type=2)
(product dependent)
whitebalance
auto, manual
4/4
“auto” indicates auto white balance.
“manual” indicates keep current value.
exposurelevel
1~8
4/4
Exposure level (product dependent)
enableblc
<boolean>
4/4
Enable backlight compensation.
agc
0~2
4/4
Set auto gain control to normal level or MAX level.
daynight
auto, schedule,
6/6
auto => auto daynight
on, off
on => ircut filter on
off => ircut filter off
schedule => scheduled ircut filter
(FD8134 only)
color
0, 1
4/4
0 =>monochrome
1 => color
flip
<boolean>
4/4
Flip the image.
mirror
<boolean>
4/4
Mirror the image.
ptzstatus
<integer>
1/7
A 32-bit integer, each bit can be set separately as
follows:
Bit 0 => Support camera control function; 0(not
support), 1(support)
Bit 1 => Built-in or external camera; 0
(external), 1(built-in)
Bit 2 => Support pan operation; 0(not support),
1(support)
Bit 3 => Support tilt operation; 0(not support),
1(support)
Bit 4 => Support zoom operation; 0(not support),
1(support)
Bit 5 => Support focus operation; 0(not support),
1(support)
text
114 - User's Manual
string[16]
1/4
Enclose caption.
VIVOTEK
imprinttimestamp
<boolean>
4/4
Overlay time stamp on video.
maxexposure
1~30
4/4
Maximum exposure time.
whitebalance
0~1
4/4
0: auto tracking white balance
<product dependent>
enableblc
1: white balance control
0~1
4/4
Enable backlight compensation
s<0~(m-1)>_codecty
mpeg4,
1/4
Video codec type.
pe
mjpeg,
1/4
Video resolution in pixels.
4/4
Intra frame period in milliseconds.
4/4
cbr, constant bitrate
<product dependent>
h264
s<0~(m-1)>_resoluti
1M CMOS
on
176x144,
320x200
640x400
1280x720
1280x800
s<0~(m-1)>_mpeg4_
250, 500,
intraperiod
1000, 2000,
3000, 4000
s<0~(m-1)>_mpeg4_
cbr, vbr
ratecontrolmode
s<0~(m-1)>_mpeg4_
vbr, fix quality
0, 1~5
4/4
quant
Quality of video when choosing vbr in
“ratecontrolmode”.
0 is the customized manual input setting.
1 = worst quality, 5 = best quality.
s<0~(m-1)>_mpeg4_
1000~800000
bitrate
0
s<0~(m-1)>_h264_in
250, 500,
traperiod
1000, 2000,
4/4
Set bit rate in bps when choosing cbr in
“ratecontrolmode”.
4/4
Intra frame period in milliseconds.
4/4
cbr, constant bitrate
3000, 4000
s<0~(m-1)>_h264_r
cbr, vbr
atecontrolmode
s<0~(m-1)>_h264_q
vbr, fix quality
1~5,99
4/4
uant
Quality of video when choosing vbr in
“ratecontrolmode”.
0 is the customized manual input setting.
1 = worst quality, 5 = best quality.
s<0~(m-1)>_h264_q
0~51
4/4
value
Manual video quality level input - choose customize
input “h264_quant = 0” (for MPEG-4).
s<0~(m-1)>_h264_bi
1000~800000
trate
0
4/4
Set bit rate in bps when choosing cbr in
“ratecontrolmode”.
User's Manual - 115
VIVOTEK
s<0~(m-1)>_h264_m
1~25,
axframe
26~30 (only
1/4
Set maximum frame rate in fps (for MPEG-4).
1/4
Indicate H264 profiles
for NTSC or
60Hz CMOS)
s<0~(m-1)>_h264_p
0~2
rofile
0: baseline
1: main profile
2: high profile
s<0~(m-1)>_mpeg4_
1~25,
maxframe
26~30 (only
1/4
Set maximum frame rate in fps (for MPEG-4).
4/4
Manual video quality level input - choose customize
for NTSC or
60Hz CMOS)
s<0~(m-1)>_mpeg4_
1~31
qvalue
input “mpeg4_quant = 0” (for MPEG-4).
s<0~(m-1)>_mjpeg_
0~5
4/4
quant
Quality of JPEG video.
0 is the customized manual input setting.
1 = worst quality, 5 = best quality.
s<0~(m-1)>_mjpeg_
1~25,
maxframe
26~30 (only
1/4
Set maximum frame rate in fps (for JPEG).
4/4
Manual video quality level input - choose customize
for NTSC or
60Hz CMOS)
s<0~(m-1)>_mjpeg_
10~200
qvalue
s<0~(m-1)>_forcei
input “mjpeg_quant = 0” (for MJPEG).
1
7/6
Force I frame.
7.7.1.1 Alternative Video Input Profiles per Channel
In addition to the primary setting of video input, there can be alternative profile video input setting for each
channel which might be for different scene of light (daytime or nighttime).
Group: videoin_profile_i<0~(m-1)> (product dependent)
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
enable
<boolean>
4/4
Enable/disable this profile setting
policy
day,
4/4
The mode which the profile is applied to.
night,
schedule
begintime
hh:mm
4/4
Begin time of schedule mode.
endtime
hh:mm
4/4
End time of schedule mode.
exposurelevel
1~8
4/4
Exposure level
maxexposure
1~30
4/4
Maximum exposure time.
116 - User's Manual
VIVOTEK
agc
0~2
4/4
Auto gain control
enableblc
<boolean>
4/4
Enable backlight compensation.
7.8 Video Input Preview
The temporary settings for video preview
Group: videoinpreview
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
enableblc
<boolean>
4/4
Preview of enable backlight compensation.
agc
0~2
4/4
Preview of set auto gain control to normal level
or MAX level.
0->normal,
1->max
exposurelevel
1~8
4/4
Preview of exposure level (product dependent)
whitebalance
0~1
4/4
0: auto tracking white balance
1: white balance control
enableblc
0~1
4/4
Enable backlight compensation
7.9 IR Cut Control (FD8134 only)
Group: ircutcontrol
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
mode
auto,
6/6
Set IR cut control mode
day,
night,
di,
schedule
daymodebegintime
00:00~23:59
6/6
Day mode begin time
daymodeendtime
00:00~23:59
6/6
Day mod end time
disableirled
<boolean>
6/6
Enable/disable IR led
bwmode
<boolean>
6/6
Switch to B/W in night mode if enabled
sensitivity
low,
6/6
Sensitivity of light sensor
normal,
high
User's Manual - 117
VIVOTEK
7.10 Image Setting per Channel
Group: image_c<0~(n-1)> for n channel products
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
brightness
-5 ~ 5
4/4
Adjust brightness of image according to mode settings.
saturation
-5 ~ 5
4/4
Adjust saturation of image according to mode settings.
contrast
-5 ~ 5
4/4
Adjust contrast of image according to mode settings.
sharpness
-3 ~ 3
4/4
Adjust sharpness of image according to mode settings.
mode
preview,
7/4
Preview => Apply the parameters of image without saving.
restore,
Restore => Restore the previous saved image parameters.
save
Save => Directly save the adjust image parameters.
7.11 Image Setting for Preview
Group: imagepreview_c<0~(n-1)> for n channel products
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
brightness
-5 ~ 5
4/4
Preview of brightness adjustment of image according to mode settings.
saturation
-5 ~ 5
4/4
Preview of saturation adjustment of image according to mode settings.
contrast
-5 ~ 5
4/4
Preview of contrast adjustment of image according to mode settings.
sharpness
-3 ~ 3
4/4
Preview of sharpness adjustment of image according to mode settings.
Group: imagepreview
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
videoin_whitebalance
auto,
4/4
Preview of adjusting white balance of image according
manual
videoin_restoreatwb
0, 1~
to mode settings
4/4
Restore of adjusting white balance of image according
to mode settings
7.12 Time Shift Settings
Group: timeshift, c for n channel products, m is stream number (product dependent)
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
enable
<boolean>
4/4
Enable time shift streaming.
c<0~(n-1)>_s<0~(
<boolean>
4/4
Enable time shift streaming for specific stream.
m-1)>_allow
118 - User's Manual
(product dependent)
VIVOTEK
7.13 Motion Detection Settings
Group: motion_c<0~(n-1)> for m profile and n channel product
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
enable
<boolean>
4/4
Enable motion detection.
win_i<0~2>_enable
<boolean>
4/4
Enable motion window 1~3.
win_i<0~2>_name
string[14]
4/4
Name of motion window 1~3.
win_i<0~2>_left
0 ~ 320
4/4
Left coordinate of window position.
win_i<0~2>_top
0 ~ 240
4/4
Top coordinate of window position.
win_i<0~2>_width
0 ~ 320
4/4
Width of motion detection window.
win_i<0~2>_height
0 ~ 240
4/4
Height of motion detection window.
win_i<0~2>_objsize
0 ~ 100
4/4
Percent of motion detection window.
win_i<0~2>_sensitivity
0 ~ 100
4/4
Sensitivity of motion detection
window.
profile_i<0~(m-1)>_enable
<boolean>
4/4
Enable profile 1 ~ (m-1).
profile_i<0~(m-1)>_policy
day,
4/4
The mode which the profile is
night,
applied to.
schedule
profile_i<0~(m-1)>_begintime
hh:mm
4/4
Begin time of schedule mode.
profile_i<0~(m-1)>_endtime
hh:mm
4/4
End time of schedule mode.
profile_i<0~(m-1)>_win_i<0~2>_enab
<boolean>
4/4
Enable motion window.
string[14]
4/4
Name of motion window.
profile_i<0~(m-1)>_win_i<0~2>_left
0 ~ 320
4/4
Left coordinate of window position.
profile_i<0~(m-1)>_win_i<0~2>_top
0 ~ 240
4/4
Top coordinate of window position.
profile_i<0~(m-1)>_win_i<0~2>_widt
0 ~ 320
4/4
Width of motion detection window.
0 ~ 240
4/4
Height of motion detection window.
0 ~ 100
4/4
Percent of motion detection window.
0 ~ 100
4/4
Sensitivity of motion detection
le
profile_i<0~(m-1)>_win_i<0~2>_nam
e
h
profile_i<0~(m-1)>_win_i<0~2>_heig
ht
profile_i<0~(m-1)>_win_i<0~2>_objsi
ze
profile_i<0~(m-1)>_win_i<0~2>_sensi
tivity
window.
<product dependent>
User's Manual - 119
VIVOTEK
7.14 Tampering Detection Settings
Group: tampering_c<0~(n-1)> for n channel product (product dependent)
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
enable
<boolean>
4/4
Enable or disable tamper detection.
threshold
0 ~ 255
4/4
Threshold of tamper detection.
duration
10 ~ 600
4/4
If tampering value exceeds the ‘threshold’ for
more than ‘duration’ second(s), then tamper
detection is triggered.
7.15 DDNS
Group: ddns
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
enable
<boolean>
6/6
Enable or disable the dynamic DNS.
provider
Safe100,
6/6
Safe100 => safe100.net
DyndnsDynamic,
DyndnsDynamic => dyndns.org (dynamic)
DyndnsCustom,
DyndnsCustom => dyndns.org (custom)
TZO,
TZO => tzo.com
DHS,
DHS => dhs.org
DynInterfree,
DynInterfree =>dyn-interfree.it
CustomSafe100
CustomSafe100 =>
Custom server using safe100 method
<provider>_hostname
string[128]
6/6
Your DDNS hostname.
<provider>_usernameem
string[64]
6/6
Your user name or email to login to the
ail
DDNS service provider
<provider>_passwordkey
string[64]
6/6
Your password or key to login to the DDNS
service provider.
<provider>_servername
string[128]
6/6
The server name for safe100.
(This field only exists if the provider is
customsafe100)
7.16 UPnP Presentation
Group: upnppresentation
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
enable
120 - User's Manual
<boolean>
6/6
Enable or disable the UPnP presentation service.
VIVOTEK
7.17 UPnP Port Forwarding
Group: upnpportforwarding
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
enable
<boolean>
6/6
Enable or disable the UPnP port forwarding service.
upnpnatstatus
0~3
6/7
The status of UPnP port forwarding, used internally.
0 = OK, 1 = FAIL, 2 = no IGD router, 3 = no need for
port forwarding
7.18 System Log
Group: syslog
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
enableremotelog
<boolean>
6/6
Enable remote log.
serverip
<IP address>
6/6
Log server IP address.
serverport
514, 1025~65535
6/6
Server port used for log.
level
0~7
6/6
Levels used to distinguish the importance of the
information:
0: LOG_EMERG
1: LOG_ALERT
2: LOG_CRIT
3: LOG_ERR
4: LOG_WARNING
5: LOG_NOTICE
6: LOG_INFO
7: LOG_DEBUG
7.19 SNMP
Group: snmp (capability.snmp) (product dependent)
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
v2
0~1
6/6
SNMP v2 enabled. 0 for disable, 1 for enable
v3
0~1
6/6
SNMP v3 enabled. 0 for disable, 1 for enable
secnamerw
string[31]
6/6
Read/write security name
secnamero
string[31]
6/6
Read only security name
authpwrw
string[8~128]
6/6
Read/write authentication password
authpwro
string[8~128]
6/6
Read only authentication password
User's Manual - 121
VIVOTEK
authtyperw
MD5,SHA
6/6
Read/write authentication type
authtypero
MD5,SHA
6/6
Read only authentication type
encryptpwrw
string[8~128]
6/6
Read/write passwrd
encryptpwro
string[8~128]
6/6
Read only password
encrypttyperw
DES
6/6
Read/write encryption type
encrypttypero
DES
6/6
Read only encryption type
rwcommunity
string[31]
6/6
Read/write community
rocommunity
string[31]
6/6
Ready only community
Group: snmp (capability.snmp) (product dependent, VS7101)
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
versions
1~3
6/6
SNMP version to use.
rocomm
string[14]
6/6
V1, V2c Read only community.
rwcomm
string[14]
6/6
V1, V2c Read write community.
adminauthtype
0~2
6/6
Authority type for root authentication.
admindpvcy
string[64]
6/6
Root data encryption key.
enableadpvcy
<boolean>
6/6
Enable root data encryption key.
userauthtype
0~2
6/6
User authority authentication.
userdpvcy
string[64]
6/6
User data encryption key.
enableudpvcy
<boolean>
6/6
Enable user data encryption key.
trapserver
<ip address>,
6/6
Trap server
<domain
name>
[128]
trapcomm
string[14]
6/6
Trap community
objectid
string[40]
6/6
Object ID
7.20 Layout Configuration
Group: layout (Old version) (Only for VS7100, EM7100)
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
layouttype
1, 2
1/4
Layout type of main page:
1: image mode
2: text mode
fontcolor
0 ~ 15
1/4
Font color of main page.
backgroundcolor
0 ~ 15
1/4
Background color of the main page.
logotype
1~3
1/4
Source type of logo:
1: default
122 - User's Manual
VIVOTEK
2: blank
3: user defined
backgroundtype
1~3
1/4
Source type of background:
1: default
2: blank
3: user defined
logolinktype
1~3
1/4
Type of logo link:
1: default
2: blank
3: user defined
logosource
string[128]
1/4
URL logo
backgroundsource
string[128]
1/4
URL background
logolink
string[128]
1/4
URL link for the logo
videolinkname
string[40]
1/4
Customized video name in text mode
Group: layout (New version)
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
logo_default
<boolean>
1/6
0 => Custom logo
1 => Default logo
logo_link
string[40]
1/6
Hyperlink of the logo
logo_powerbyvvtk_hidden
<boolean>
1/6
0 => display the power by vivotek logo
1 => hide the power by vivotek logo
theme_option
1~4
1/6
1~3: One of the default themes.
4: Custom definition.
theme_color_font
string[7]
1/6
Font color
theme_color_configfont
string[7]
1/6
Font color of configuration area.
theme_color_titlefont
string[7]
1/6
Font color of video title.
theme_color_controlbackground
string[7]
1/6
Background color of control area.
theme_color_configbackground
string[7]
1/6
Background color of configuration area.
theme_color_videobackground
string[7]
1/6
Background color of video area.
theme_color_case
string[7]
1/6
Frame color
custombutton_manualtrigger_s
<boolean>
1/6
Show or hide manual trigger (VI) button in
how
homepage
0 -> Hidden
1 -> Visible
User's Manual - 123
VIVOTEK
7.22 Privacy Mask
Group: privacymask_c<0~(n-1)> for n channel product
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
enable
<boolean>
4/4
Enable privacy mask.
win_i<0~4>_enable
<boolean>
4/4
Enable privacy mask window.
win_i<0~4>_name
string[14]
4/4
Name of the privacy mask window.
win_i<0~4>_left
0 ~ 320/352
4/4
Left coordinate of window position.
win_i<0~4>_top
0 ~ 240/288
4/4
Top coordinate of window position.
win_i<0~4>_width
0 ~ 320/352
4/4
Width of privacy mask window.
win_i<0~4>_height
0 ~ 240/288
4/4
Height of privacy mask window.
7.23 Capability
Group: capability
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
api_httpversion
0200a
0/7
The HTTP API version.
bootuptime
<positive integer>
0/7
Server bootup time.
nir
0,
0/7
Number of IR interfaces.
0/7
Number of PIRs.
0/7
Number of digital inputs.
0/7
Number of digital outputs.
0/7
Number of audio inputs.
0/7
Number of audio outputs.
<positive integer>
npir
0,
<positive integer>
ndi
0,
<positive integer>
ndo
0,
<positive integer>
naudioin
0,
<positive integer>
naudioout
0,
<positive integer>
nvideoin
<positive integer>
0/7
Number of video inputs.
nmediastream
<positive integer>
0/7
Number of media stream per channels.
nvideosetting
<positive integer>
0/7
Number of video settings per channel.
naudiosetting
<positive integer>
0/7
Number of audio settings per channel.
nuart
0,
0/7
Number of UART interfaces.
<positive integer>
124 - User's Manual
VIVOTEK
nmotionprofile
<positive integer>
0/7
Number of motion profiles.
ptzenabled
<positive integer>
0/7
An 32-bit integer, each bit can be set
separately as follows:
Bit 0 => Support camera control function;
0(not support), 1(support)
Bit 1 => Built-in or external camera;
0(external), 1(built-in)
Bit 2 => Support pan operation, 0(not
support), 1(support)
Bit 3 => Support tilt operation; 0(not
support), 1(support)
Bit 4 => Support zoom operation;
0(not support), 1(support)
Bit 5 => Support focus operation;
0(not support), 1(support)
Bit 6 => Support iris operation;
0(not support), 1(support)
Bit 7 => External or built-in PT; 0(built-in),
1(external)
Bit 8 => Invalidate bit 1 ~ 7;
0(bit 1 ~ 7 are valid),
1(bit 1 ~ 7 are invalid)
Bit 9 => Reserved bit; Invalidate lens_pan,
Lens_tilt, lens_zoon, lens_focus, len_iris.
0(fields are valid),
1(fields are invalid)
eptz
<positive integer>
0/7
A 32-bit integer, each bit can be set
separately as follows:
Bit 0 => stream 1 supports ePTZ or not.
Bit 1 => stream 2 supports ePTZ or not.
The rest may be deduced by analogy
npreset
<positive integer>
0/7
Number of preset locations.
protocol_https
< boolean >
0/7
Indicate whether to support HTTP over SSL.
protocol_rtsp
< boolean >
0/7
Indicate whether to support RTSP.
protocol_sip
<boolean>
0/7
Indicate whether to support SIP.
protocol_maxconnecti
<positive integer>
0/7
The maximum allowed simultaneous
on
protocol_maxgenconn
ection
connections.
<positive integer>
0/7
The maximum general streaming
connections .
User's Manual - 125
VIVOTEK
protocol_maxmegaco
<positive integer>
0/7
nnection
protocol_rtp_multicast
connections.
<boolean>
0/7
_scalable
protocol_rtp_multicast
The maximum megapixel streaming
Indicate whether to support scalable
multicast.
<boolean>
0/7
_backchannel
Indicate whether to support backchannel
multicast.
protocol_rtp_tcp
<boolean>
0/7
Indicate whether to support RTP over TCP.
protocol_rtp_http
<boolean>
0/7
Indicate whether to support RTP over HTTP.
protocol_spush_mjpe
<boolean>
0/7
Indicate whether to support server push
g
MJPEG.
protocol_snmp
<boolean>
0/7
Indicate whether to support SNMP.
protocol_ipv6
<boolean>
0/7
Indicate whether to support IPv6.
videoin_type
0, 1, 2
0/7
0 => Interlaced CCD
1 => Progressive CCD
2 => CMOS
videoin_resolution
<a list of available
0/7
Available resolutions list.
0/7
Available maximum frame list.
0/7
Available codec list.
0/7
Indicate transmission mode of the machine:
resolution separated
by commas>
videoin_maxframerate
<a list of available
maximum frame rate
separated by
commas>
videoin_codec
<a list of available
codec types
separated by
commas>
transmission_mode
Tx,
Rx,
TX = server, Rx = receiver box, Both = DVR.
Both
network_wire
<boolean>
0/7
Indicate whether to support Ethernet.
network_wireless
<boolean>
0/7
Indicate whether to support wireless.
wireless_s802dot11b
<boolean>
0/7
Indicate whether to support wireless
802.11b+.
wireless_s802dot11g
<boolean>
0/7
Indicate whether to support wireless
802.11g.
wireless_beginchannel
126 - User's Manual
1 ~ 14
0/7
Indicate the begin channel of wireless
VIVOTEK
network
wireless_endchannel
1 ~ 14
0/7
Indicate the end channel of wireless
network
wireless_encrypt_wep
<boolean>
0/7
Indicate whether to support wireless WEP.
wireless_encrypt_wpa
<boolean>
0/7
Indicate whether to support wireless WPA.
wireless_encrypt_wpa
<boolean>
0/7
Indicate whether to support wireless WPA2.
<boolean>
0/7
Indicate whether to support the upgrade
2
derivative_brand
function for the derivative brand. For
example, if the value is true, the VVTK
product can be upgraded to VVXX.
(TCVV<->TCXX is excepted)
joystick
<boolean>
0/7
Indicate whether to support joystick
control.
storage_dbenabled
<boolean>
0/7
Media files are indexed in database.
nanystream
<positive integer>
0/7
number of any media stream per channel
iva
<boolean>
0/7
Indicate whether to support Intelligent
Video analysis
whitelight
<boolean>
0/7
Indicate whether to support white light led.
tampering
<boolean>
0/7
Indicate whether to support tampering
detection.
temperature
<boolean>
0/7
Indicate whether to support temperature
detection.
version_onvifdaemon
<string>
0/7
Indicate ONVIF daemon version
7.24 Customized Event Script
Group: event_customtaskfile_i<0~2>
PARAMETER
VALUE
SECURITY
DESCRIPTION
(get/set)
name
string[41]
6/7
Custom script identification of this entry.
date
string[17]
6/7
Date of custom script.
time
string[17]
6/7
Time of custom script.
VALUE
SECURITY
DESCRIPTION
Group: custom_i<0~2>
PARAMETER
(get/set)
name
string[40]
6/6
Identification of customized event script file.
User's Manual - 127
VIVOTEK
7.25 Event Setting
Group: event_i<0~2>
PARAMETER
VALUE
SECURITY DESCRIPTION
(get/set)
name
string[40]
6/6
Identification of this entry.
enable
0, 1
6/6
Enable or disable this event.
priority
0, 1, 2
6/6
Indicate the priority of this event:
“0” = low priority
“1” = normal priority
“2” = high priority
delay
1~999
6/6
Delay in seconds before detecting the next event.
trigger
boot,
6/6
Indicate the trigger condition:
di,
“boot” = System boot
motion,
“di”= Digital input
seq,
“motion” = Video motion detection
recnotify,
“seq” = Periodic condition
tampering,
“recnotify” = Recording notification.
“tampering” = Tamper detection.
triggerstatus
String[40]
6/6
The status for event trigger
di
<integer>
6/6
Indicate the source id of di trigger.
This field is required when trigger condition is “di”.
One bit represents one digital input. The LSB indicates DI 0.
mdwin
<integer>
6/6
Indicate the source window id of motion detection.
This field is required when trigger condition is “md”.
One bit represents one window.
The LSB indicates the 1st window.
For example, to detect the 1st and 3rd windows, set mdwin as 5.
mdwin0
<integer>
6/6
Similar to mdwin. The parameter takes effect when profile 1 of
motion detection is enabled.
inter
1~999
6/6
Interval of snapshots in minutes.
This field is used when trigger condition is “seq”.
128 - User's Manual
VIVOTEK
weekday
0~127
6/6
Indicate which weekday is scheduled.
One bit represents one weekday.
bit0 (LSB) = Saturday
bit1 = Friday
bit2 = Thursday
bit3 = Wednesday
bit4 = Tuesday
bit5 = Monday
bit6 = Sunday
For example, to detect events on Friday and Sunday, set
weekday as 66.
begintime
hh:mm
6/6
Begin time of the weekly schedule.
endtime
hh:mm
6/6
End time of the weekly schedule.
(00:00 ~ 24:00 sets schedule as always on)
action_cf_enable 0. 1
6/6
Enable media write on CF or other local storage media
action_cf_folder string[128]
6/6
Path to store media.
action_cf_media NULL, 0~4
6/6
Index of the attached media.
action_cf_datefol <boolean>
6/6
Enable this to create folders by date, time, and hour
der
automatically.
action_server_i< 0, 1
6/6
Enable or disable this server action.
6/6
Index of the attached media.
6/6
Enable this to create folders by date, time, and hour
0~4>_enable
action_server_i< NULL, 0~4
0~4>_media
action_server_i< <boolean>
0~4>_datefolder
automatically.
7.26 Server Setting for Event Action
Group: server_i<0~4>
PARAMETER
VALUE
SECURITY
DESCRIPTION
(get/set)
name
string[40]
6/6
Identification of this entry
type
email,
6/6
Indicate the server type:
ftp,
“email” = email server
http,
“ftp” = FTP server
ns
“http” = HTTP server
“ns” = network storage
http_url
string[128]
6/6
URL of the HTTP server to upload.
http_username
string[64]
6/6
Username to log in to the server.
User's Manual - 129
VIVOTEK
http_passwd
string[64]
6/6
Password of the user.
ftp_address
string[128]
6/6
FTP server address.
ftp_username
string[64]
6/6
Username to log in to the server.
ftp_passwd
string[64]
6/6
Password of the user.
ftp_port
0~65535
6/6
Port to connect to the server.
ftp_location
string[128]
6/6
Location to upload or store the media.
ftp_passive
0, 1
6/6
Enable or disable passive mode.
0 = disable passive mode
1 = enable passive mode
email_address
string[128]
6/6
Email server address.
email_sslmode
0, 1
6/6
Enable support SSL.
email_port
0~65535
6/6
Port to connect to the server.
email_username
string[64]
6/6
Username to log in to the server.
email_passwd
string[64]
6/6
Password of the user.
email_senderemail
string[128]
6/6
Email address of the sender.
email_recipientemail
string[128]
6/6
Email address of the recipient.
ns_location
string[128]
6/6
Location to upload or store the media.
ns_username
string[64]
6/6
Username to log in to the server.
ns_passwd
string[64]
6/6
Password of the user.
ns_workgroup
string[64]
6/6
Workgroup for network storage.
7.27 Media Setting for Event Action
Group: media_i<0~4> (media_freespace is used internally.)
PARAMETER
VALUE
SECURITY
DESCRIPTION
(get/set)
name
string[40]
6/6
Identification of this entry
type
snapshot,
6/6
Media type to send to the server or store on the
systemlog,
server.
videoclip,
recordmsg
snapshot_source
<integer>
6/6
Indicate the source of media stream.
0 means the first stream.
1 means the second stream and etc.
2 means the third stream and etc.
3 means the fourth stream and etc.
snapshot_prefix
130 - User's Manual
string[16]
6/6
Indicate the prefix of the filename.
VIVOTEK
snapshot_datesuffix
0, 1
6/6
Add date and time suffix to filename:
1 = Add date and time suffix.
0 = Do not add.
snapshot_preevent
0~7
6/6
Indicates the number of pre-event images.
snapshot_postevent
0~7
6/6
The number of post-event images.
videoclip_source
<integer>
6/6
Indicate the source of media stream.
0 means the first stream.
1 means the second stream and etc.
2 means the third stream and etc.
3 means the fourth stream and etc.
videoclip_prefix
string[16]
6/6
Indicate the prefix of the filename.
videoclip_preevent
0~9
6/6
Indicates the time for pre-event recording in
seconds.
videoclip_maxduration
1 ~ 10
6/6
Maximum duration of one video clip in seconds.
videoclip_maxsize
50 ~ 4096
6/6
Maximum size of one video clip file in Kbytes.
SECURITY
DESCRIPTION
7.28 Recording
Group: recording_i<0~1>
PARAMETER
VALUE
(get/set)
name
string[40]
6/6
Identification of this entry.
enable
0, 1
6/6
Enable or disable this recording.
adaptive_enable
0, 1
6/6
Enable or disable adaptive recording
adaptive_preevent
0~9
6/6
Pre-time of adaptive recording
adaptive_postevent
0~9
6/6
Post-time of adaptive recording
priority
0, 1, 2
6/6
Indicate the priority of this recording:
“0” indicates low priority.
“1” indicates normal priority.
“2” indicates high priority.
source
<integer>
6/6
Indicate the source of media stream.
0 means the first stream.
1 means the second stream and etc.
2 means the third stream and etc.
3 means the fourth stream and etc.
limitsize
0,1
6/6
0: Entire free space mechanism
1: Limit recording size mechanism
cyclic
0,1
6/6
0: Disable cyclic recording
1: Enable cyclic recording
User's Manual - 131
VIVOTEK
notify
0,1
6/6
0: Disable recording notification
1: Enable recording notification
notifyserver
0~31
6/6
Indicate which notification server is scheduled.
One bit represents one application server
(server_i0~i4).
bit0 (LSB) = server_i0.
bit1 = server_i1.
bit2 = server_i2.
bit3 = server_i3.
bit4 = server_i4.
For example, enable server_i0, server_i2, and
server_i4 as notification servers; the notifyserver
value is 21.
weekday
0~127
6/6
Indicate which weekday is scheduled.
One bit represents one weekday.
bit0 (LSB) = Saturday
bit1 = Friday
bit2 = Thursday
bit3 = Wednesday
bit4 = Tuesday
bit5 = Monday
bit6 = Sunday
For example, to detect events on Friday and
Sunday, set weekday as 66.
begintime
hh:mm
6/6
Start time of the weekly schedule.
endtime
hh:mm
6/6
End time of the weekly schedule.
(00:00~24:00 indicates schedule always on)
prefix
string[16]
6/6
Indicate the prefix of the filename.
cyclesize
20~
6/6
The maximum size for cycle recording in Kbytes
when choosing to limit recording size.
reserveamount
15~
6/6
The reserved amount in Mbytes when choosing
cyclic recording mechanism.
dest
cf,
6/6
0~4
The destination to store the recorded data.
“cf” means CF card.
“0~4” means the index of the network storage.
cffolder
132 - User's Manual
string[128]
6/6
Folder name.
VIVOTEK
7.29 HTTPS
Group: https (product dependent)
NAME
VALUE
SECURITY
DESCRIPTION
(get/set)
enable
<boolean>
6/6
To enable or disable secure HTTP.
policy
<Boolean>
6/6
If the value is 1, it will force HTTP connection
redirect to HTTPS connection
method
auto,
6/6
auto => Create self-signed certificate
manual,
automatically.
install
manual => Create self-signed certificate manually.
install => Create certificate request and install.
status
-3 ~ 1
6/7
Specify the https status.
-3 = Certificate not installed
-2 = Invalid public key
-1 = Waiting for certificate
0 = Not installed
1 = Active
countryname
string[2]
6/6
Country name in the certificate information.
stateorprovincename
string[128]
6/6
State or province name in the certificate
information.
localityname
string[128]
6/6
The locality name in the certificate information.
organizationname
string[64]
6/6
Organization name in the certificate information.
unit
string[32]
6/6
Organizational unit name in the certificate
information.
commonname
string[64]
6/6
Common name in the certificate information.
validdays
0 ~ 9999
6/6
Valid period for the certification.
7.30 Storage Management Setting
Currently it’s for local storage (SD, CF card)
Group: disk_i<0~(n-1)> n is the total number of storage devices.
PARAMETER
VALUE
SECURITY
DESCRIPTION
(get/set)
cyclic_enabled
<boolean>
6/6
Enable cyclic storage method.
autocleanup_enabled
<boolean>
6/6
Enable automatic clean up method.
Expired and not locked media files will be deleted.
autocleanup_maxage
<positive
6/6
To specify the expired days for automatic clean up.
integer>
User's Manual - 133
VIVOTEK
7.31 Region of Interest
Group: roi_c<0~(n-1)> for n channel product, and m is the number of streams which support ROI.
PARAMETER
VALUE
SECURITY
DESCRIPTION
(get/set)
s<0~(m-1)>_home
<coordinate>
6/6
s<0~(m-1)>_size
<window size> 6/6
ROI left-top corner coordinate.
ROI width and height. The width value must be
multiples of 16 and the height value must be
multiples of 8
134 - User's Manual
VIVOTEK
Useful Functions
8.1 Query Status of the Digital Input
Note: This request requires Viewer privileges
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/dido/getdi.cgi?[di0][&di1][&di2][&di3]
If no parameter is specified, all of the digital input statuses will be returned.
Return:
HTTP/1.0 200 OK\r\n
Content-Type: text/plain\r\n
Content-Length: <length>\r\n
\r\n
[di0=<state>]\r\n
[di1=<state>]\r\n
[di2=<state>]\r\n
[di3=<state>]\r\n
where <state> can be 0 or 1.
Example: Query the status of digital input 1.
Request:
http://myserver/cgi-bin/dido/getdi.cgi?di1
Response:
HTTP/1.0 200 OK\r\n
Content-Type: text/plain\r\n
Content-Length: 7\r\n
\r\n
Di1=1\r\n
8.2 Capture Single Snapshot
Note: This request requires Normal User privileges.
Method: GET/POST
Syntax:
User's Manual - 135
VIVOTEK
http://<servername>/cgi-bin/viewer/video.jpg?[channel=<value>][&resolution=<value>]
[&quality=<value>][&streamid=<value>]
If the user requests a size larger than all stream settings on the server, this request will fail.
PARAMETER
VALUE
DEFAULT
DESCRIPTION
channel
0~(n-1)
0
The channel number of the video source.
resolution
<available resolution> 0
The resolution of the image.
quality
1~5
3
The quality of the image.
streamid
0~(m-1)
<product dependent> The stream number.
<product
dependent>
The server will return the most up-to-date snapshot of the selected channel and stream in JPEG format. The
size and quality of the image will be set according to the video settings on the server.
Return:
HTTP/1.0 200 OK\r\n
Content-Type: image/jpeg\r\n
[Content-Length: <image size>\r\n]
<binary JPEG image data>
8.3 Account Management
Note: This request requires Administrator privileges.
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/admin/editaccount.cgi?
method=<value>&username=<name>[&userpass=<value>][&privilege=<value>]
[&privilege=<value>][…][&return=<return page>]
PARAMETER
VALUE
DESCRIPTION
method
Add
Add an account to the server. When using this method, the “username” field
is necessary. It will use the default value of other fields if not specified.
Delete
Remove an account from the server. When using this method, the
“username” field is necessary, and others are ignored.
136 - User's Manual
VIVOTEK
edit
Modify the account password and privilege. When using this method, the
“username” field is necessary, and other fields are optional. If not specified,
it will keep the original settings.
username
<name>
The name for the user to add, delete, or edit.
userpass
<value>
The password of the new user to add or that of the old user to modify. The
default value is an empty string.
Privilege
Return
<value>
The privilege of the user to add or to modify.
viewer
Viewer privilege.
operator
Operator privilege.
admin
Administrator privilege.
<return page>
Redirect to the page <return page> after the parameter is assigned. The
<return page> can be a full URL path or relative path according to the
current path. If you omit this parameter, it will redirect to an empty page.
8.4 System Logs
Note: This request requires Administrator privileges.
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/admin/syslog.cgi
Server will return the most up-to-date system log.
Return:
HTTP/1.0 200 OK\r\n
Content-Type: text/plain\r\n
Content-Length: <syslog length>\r\n
\r\n
<system log information>\r\n
8.5 Upgrade Firmware
Note: This request requires Administrator privileges.
Method: POST
Syntax:
http://<servername>/cgi-bin/admin/upgrade.cgi
Post data:
User's Manual - 137
VIVOTEK
fimage=<file name>[&return=<return page>]\r\n
\r\n
<multipart encoded form data>
Server will accept the file named <file name> to upgrade the firmware and return with <return page> if
indicated.
8.6 IP Filtering
Note: This request requires Administrator access privileges.
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/admin/ipfilter.cgi?
method=<value>&[start=<ipaddress>&end=<ipaddress>][&index=<value>]
[&return=<return page>]
PARAMETER
VALUE
DESCRIPTION
Method
addallow
Add allowed IP address range to the server. Start and end parameters must be
specified. If the index parameter is specified, it will try to add starting from the
index position.
adddeny
Add denied IP address range to the server. Start and end parameters must be
specified. If the index parameter is specified, it will try to add starting from the
index position.
deleteallow
Remove allowed IP address range from server. If start and end parameters are
specified, it will try to remove the matched IP address. If index is specified, it
will try to remove the address from given index position. [start, end]
parameters have higher priority then the [index] parameter.
deletedeny
Remove denied IP address range from server. If start and end parameters are
specified, it will try to remove the matched IP address. If index is specified, it
will try to remove the address from given index position. [start, end]
parameters have higher priority then the [index] parameter.
start
<ip address>
The starting IP address to add or to delete.
end
<ip address>
The ending IP address to add or to delete.
index
<value>
The start position to add or to delete.
return
<return page> Redirect to the page <return page> after the parameter is assigned. The
<return page> can be a full URL path or relative path according to the current
path. If you omit this parameter, it will redirect to an empty page.
138 - User's Manual
VIVOTEK
8.7 Event/Control HTTP Tunnel Channel
Note: This request requires Administrator privileges.
Method: GET and POST
Syntax:
http://<servername>/cgi-bin/admin/ctrlevent.cgi
------------------------------------------------------------------------GET /cgi-bin/admin/ctrlevent.cgi
x-sessioncookie: string[22]
accept: application/x-vvtk-tunnelled
pragma: no-cache
cache-control: no-cache
------------------------------------------------------------------------POST /cgi-bin/admin/ ctrlevent.cgi
x-sessioncookie: string[22]
content-type: application/x-vvtk-tunnelled
pragma : no-cache
cache-control : no-cache
content-length: 32767
expires: Sun, 9 Jam 1972 00:00:00 GMT
User must use GET and POST to establish two channels for downstream and upstream. The x-sessioncookie
in GET and POST should be the same to be recognized as a pair for one session. The contents of upstream
should be base64 encoded to be able to pass through the proxy server.
This channel will help perform real-time event subscription and notification as well as camera control more
efficiently. The event and control formats are described in another document.
See Event/control tunnel spec for detail information
8.8 Get SDP of Streams
Note: This request requires Viewer access privileges.
Method: GET/POST
Syntax:
User's Manual - 139
VIVOTEK
http://<servername>/<network_rtsp_s<0~m-1>_accessname>
“m” is the stream number.
“network_accessname_<0~(m-1)>” is the accessname for stream “1” to stream “m”. Please refer to the
“subgroup of network: rtsp” for setting the accessname of SDP.
You can get the SDP by HTTP GET.
When using scalable multicast, Get SDP file which contains the multicast information via HTTP.
8.9 Open the Network Stream
Note: This request requires Viewer access privileges.
Syntax:
For HTTP push server (MJPEG):
http://<servername>/<network_http_s<0~m-1>_accessname>
For RTSP (MP4), the user needs to input the URL below into an RTSP compatible player.
rtsp://<servername>/<network_rtsp_s<0~m-1>_accessname>
“m” is the stream number.
For details on streaming protocol, please refer to the “control signaling” and “data format” documents.
8.10 Senddata (capability.nuart>0)
Note: This request requires Viewer privileges.
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/viewer/senddata.cgi?
[com=<value>][&data=<value>][&flush=<value>] [&wait=<value>] [&read=<value>]
PARAMETER
VALUE
DESCRIPTION
com
1 ~ <max. com port
The target COM/RS485 port number.
number>
data
flush
<hex decimal data>[,<hex The <hex decimal data> is a series of digits from 0 ~ 9, A ~ F.
decimal data>]
Each comma separates the commands by 200 milliseconds.
yes,no
yes: Receive data buffer of the COM port will be cleared before
140 - User's Manual
VIVOTEK
read.
no: Do not clear the receive data buffer.
wait
1 ~ 65535
Wait time in milliseconds before read data.
read
1 ~ 128
The data length in bytes to read. The read data will be in the
return page.
Return:
HTTP/1.0 200 OK\r\n
Content-Type: text/plain\r\n
Content-Length: <system information length>\r\n
\r\n
<hex decimal data>\r\n
Where hexadecimal data is digits from 0 ~ 9, A ~ F.
8.11 Storage managements
(capability.storage.dbenabled=1)
Note: This request requires administrator privileges.
Method: GET and POST
Syntax:
http://<servername>/cgi-bin/admin/lsctrl.cgi?cmd=<cmd_type>[&<parameter>=<value>…]
The commands usage and their input arguments are as follows.
PARAMETER VALUE
DESCRIPTION
cmd_type
Required.
<string>
Command to be executed, including search, insert, delete, update, and queryStatus.
Command: search
PARAMETER VALUE
label
DESCRIPTION
<integer primary key> Optional.
The integer primary key column will automatically be assigned a unique
integer.
triggerType
<text>
Optional.
Indicate the event trigger type.
Please embrace your input value with single quotes.
Ex. mediaType=’motion’
User's Manual - 141
VIVOTEK
Support trigger types are product dependent.
mediaType
<text>
Optional.
Indicate the file media type.
Please embrace your input value with single quotes.
Ex. mediaType=’videoclip’
Support trigger types are product dependent.
destPath
<text>
Optional.
Indicate the file location in camera.
Please embrace your input value with single quotes.
Ex. destPath =’/mnt/auto/CF/NCMF/abc.mp4’
resolution
<text>
Optional.
Indicate the media file resolution.
Please embrace your input value with single quotes.
Ex. resolution=’800x600’
isLocked
<boolean>
Optional.
Indicate if the file is locked or not.
0: file is not locked.
1: file is locked.
A locked file would not be removed from UI or cyclic storage.
triggerTime
<text>
Optional.
Indicate the event trigger time. (not the file created time)
Format is “YYYY-MM-DD HH:MM:SS”
Please embrace your input value with single quotes.
Ex. triggerTime=’2008-01-01 00:00:00’
If you want to search for a time period, please apply “TO” operation.
Ex. triggerTime=’2008-01-01 00:00:00’+TO+’2008-01-01 23:59:59’ is
to search for records from the start of Jan 1st 2008 to the end of Jan 1st
2008.
limit
<positive integer>
Optional.
Limit the maximum number of returned search records.
offset
<positive integer>
Optional.
Specifies how many rows to skip at the beginning of the matched
records.
Note that the offset keyword is used after limit keyword.
To increase the flexibility of search command, you may use “OR” connectors for logical “OR” search
operations. Moreover, to search for a specific time period, you can use “TO” connector.
Ex. To search records triggered by motion or di or sequential and also triggered between 2008-01-01
00:00:00 and 2008-01-01 23:59:59.
http://<servername>/cgi-bin/admin/lsctrl.cgi?cmd=search&triggerType=’motion’+OR+’di’+OR+’seq’&trigge
rTime=’2008-01-01 00:00:00’+TO+’2008-01-01 23:59:59’
142 - User's Manual
VIVOTEK
Command: delete
PARAMETER
VALUE
DESCRIPTION
label
<integer primary key>
Required.
Identify the designated record.
Ex. label=1
Ex. Delete records whose key numbers are 1, 4, and 8.
http://<servername>/cgi-bin/admin/lsctrl.cgi?cmd=delete&label=1&label=4&label=8
Command: update
PARAMETER
VALUE
DESCRIPTION
label
<integer primary key>
Required.
Identify the designated record.
Ex. label=1
isLocked
<boolean>
Required.
Indicate if the file is locked or not.
Ex. Update records whose key numbers are 1 and 5 to be locked status.
http://<servername>/cgi-bin/admin/lsctrl.cgi?cmd=update&isLocked=1&label=1&label=5
Ex. Update records whose key numbers are 2 and 3 to be unlocked status.
http://<servername>/cgi-bin/admin/lsctrl.cgi?cmd=update&isLocked=0&label=2&label=3
Command: queryStatus
PARAMETER
VALUE
DESCRIPTION
retType
xml or javascript
Optional.
Ex. retype=javascript
The default return message is in XML format.
Ex. Query local storage status and call for javascript format return message.
http://<servername>/cgi-bin/admin/lsctrl.cgi?cmd=queryStatus&retType=javascript
User's Manual - 143
VIVOTEK
Ver 0�5
Technical Specifications
Specifications
Model
.FD8133 (Wired)
.FD8134 (PoE)
System
.CPU: TI DM365 SoC
.Flash: 128MB
.RAM: 256MB
.Embedded OS: Linux 2.6
Lens
.Board lens, Fixed, f = 3.6 mm, F1.8
.Removable IR-cut filter for day & night function
(FD8134)
Users
.Live viewing for up to 10 clients
Dimension
.Ø 110 mm x 80 mm
Weight
.Net: 463 g (FD8133)
.Net: 479 g (FD8134)
LED Indicator
.System power and status indicator
.System activity and network link indicator
Power
.12V DC
.Power consumption: Max. 3.5 W
.802.3af compliant Power-over-Ethernet (Class 2) (FD8134)
Approvals
.CE, LVD, FCC, VCCI, C-Tick
Angle of View
.56°(horizontal)
.41°(vertical)
Shutter Time
.1/5 sec. to 1/25,000 sec.
Image Sensor
.1/4”CMOS sensor in 1280x800 resolution
Operating
Environments
.Temperature: 0 ~ 50°C (32 ~ 122°F)
.Humidity: 90% RH
Minimum
Illumination
.0.3 Lux @ F1.8 (FD8133)
.0 Lux @ F1.8 (IR LED on) (FD8134)
Viewing System
Requirements
IR Illuminators
(FD8134)
.Built-in IR illuminators, effective up to 10 meters
.IR LED*8 (850nm)
.OS: Microsoft Windows 7/Vista/XP/2000
.Browser: Mozilla Firefox, Internet Explorer 6.x or above
.Cell phone: 3GPP player
.Real Player: 10.5 or above
.Quick Time: 6.5 or above
Video
.Compression: H.264, MJPEG & MPEG-4
.Streaming:
Simultaneous multi-streaming
H.264 streaming over UDP, TCP, HTTP or HTTPS
MPEG-4 streaming over UDP, TCP, HTTP or HTTPS
MPEG-4 multicast streaming
MJPEG streaming over HTTP or HTTPS
.Supports activity adaptive streaming for dynamic
frame rate control
.Supports 3GPP mobile surveillance
.Frame rates:
H.264: Up to 30/25 fps at 1280x800
MPEG-4: Up to 30/25 fps at 1280x800
MJPEG: Up to 30/25 fps at 1280x800
Installation,
Management,
and Maintenance
.3-axis mechanism for flexible ceiling and wall mount
installation
.Camera angle adjustment: pan 350°, tilt 85°, rotate 350°
.Installation Wizard 2
.32-CH ST7501 recording software
.Supports firmware upgrade
Applications
.SDK available for application development
and system integration
Warranty
.12 months
Image Settings
.Adjustable image size, quality and bit rate
.Time stamp and text caption overlay
.Flip & mirror
.Configurable brightness, contrast, saturation,
sharpness, white balance and exposure
.AGC, AWB, AES
.Automatic, manual or scheduled day/night mode
(FD8134)
.BLC (Backlight Compensation)
.Supports privacy masks
Networking
.10/100 Mbps Ethernet, RJ-45
.Onvif Support
.Protocols: IPv4, IPv6, TCP/IP, HTTP, HTTPS, UPnP,
RTSP/RTP/RTCP, IGMP, SMTP, FTP,DHCP, NTP,
DNS, DDNS, PPPoE, CoS, QoS, SNMP and 802.1X
Alarm and
Event Management
.Triple-window video motion detection
.Tamper detection
.One D/I for external sensor and alarm
.Event notification using HTTP, SMTP or FTP
.Local recording of MP4 file
On-Board Storage
.MicroSD/SDHC card slot
.Stores snapshots and video clips
Security
.Muilti-level user access with password protection
.IP address filtering
.HTTPS encrypted data transmission
.802.1X port-based authentication for network protection
All specifications are subject to change without notice. Copyright c 2010 VIVOTEK INC. All rights reserved.
Distributed by:
144 - User's Manual
6F, No.192, Lien-Cheng Rd., Chung-Ho, Taipei County, Taiwan
Tel: +886 2 8245 5282| Fax: +886 2 8245 5532| E-mail: [email protected]
VIVOTEK USA, INC.
470 Lakeside Drive Suite C, Sunnyvale, CA 94085 USA
Tel: 408-773-8686 | Fax: 408-773-8298 | E-mail: [email protected]
VIVOTEK
Technology License Notice
MPEG-4 AAC Technology
THIS PRODUCT IS LICENSED UNDER THE MPEG-4 AAC AUDIO PATENT LICENSE. THIS PRODUCT MAY
NOT BE DECOMPILED, REVERSE-ENGINEERED OR COPIED, EXCEPT WITH REGARD TO PC SOFTWARE,
OF WHICH YOU MAY MAKE SINGLE COPIES FOR ARCHIVAL PURPOSES. FOR MORE INFORMATION,
PLEASE REFER TO HTTP://WWW.VIALICENSING.COM.
MPEG-4 Visual Technology
THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE
PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN COMPLIANCE
WITH THE MPEG-4 VISUAL STANDARD ("MPEG-4 VIDEO") AND/OR (ii) DECODING MPEG-4 VIDEO THAT
WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/
OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO.
NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION
INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL AND COMMERCIAL USES AND LICENSING MAY
BE OBTAINED FROM MPEG LA, LLC. PLEASE REFER TO HTTP://WWW.MPEGLA.COM.
AMR-NB Standard
THIS PRODUCT IS LICENSED UNDER THE AMR-NB STANDARD PATENT LICENSE AGREEMENT. WITH
RESPECT TO THE USE OF THIS PRODUCT, THE FOLLOWING LICENSORS’ PATENTS MAY APPLY:
TELEFONAKIEBOLAGET ERICSSON AB: US PAT. 6192335; 6275798; 6029125; 6424938; 6058359. NOKIA
CORPORATION: US PAT. 5946651; 6199035. VOICEAGE CORPORATION: AT PAT. 0516621; BE PAT. 0516621;
CA PAT. 2010830; CH PAT. 0516621; DE PAT. 0516621; DK PAT. 0516621; ES PAT. 0516621; FR PAT. 0516621;
GB PAT. 0516621; GR PAT. 0516621; IT PAT. 0516621; LI PAT. 0516621; LU PAT. 0516621; NL PAT. 0516621;
SE PAT 0516621; US PAT 5444816; AT PAT. 819303/AT E 198805T1; AU PAT. 697256; BE PAT. 819303; BR PAT.
9604838-7; CA PAT. 2216315; CH PAT. 819303; CN PAT. ZL96193827.7; DE PAT. 819303/DE69611607T2; DK
PAT. 819303; ES PAT. 819303; EP PAT. 819303; FR PAT. 819303; GB PAT. 819303; IT PAT. 819303; JP PAT. APP.
8-529817; NL PAT. 819303; SE PAT. 819303; US PAT. 5664053. THE LIST MAY BE UPDATED FROM TIME TO
TIME BY LICENSORS AND A CURRENT VERSION OF WHICH IS AVAILABLE ON LICENSOR’S WEBSITE AT
HTTP://WWW.VOICEAGE.COM.
User's Manual - 145
VIVOTEK
Electromagnetic Compatibility (EMC)
FCC Statement
This device compiles with FCC Rules Part 15. Operation is subject to the following two conditions.
■ This device may not cause harmful interference, and
■ This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a partial
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
■ Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with emission limits.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
VCCI Warning
この装置は、情報処理装置等電波障害自主規制協議会(VCCI)の基準にづくクラスB情報技術装置
です。この装置は、家庭環境で使用することを目的としていますが、この装置がラジオやテレビジョン
受信機に近接して使用されると、受信障害を引き起こすことがあります。
取扱説明書に従って正しい取り扱いをして下さい
Liability
VIVOTEK Inc. cannot be held responsible for any technical or typographical errors and reserves the right
to make changes to the product and manuals without prior notice. VIVOTEK Inc. makes no warranty
of any kind with regard to the material contained within this document, including, but not limited to, the
implied warranties of merchantability and fitness for any particular purpose.
146 - User's Manual

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement