ViewSonic | PJD7383 | User guide | Viewsonic PJD7583WI data projector

Viewsonic PJD7583WI data projector
ViewSonic
®
PJD7383/ PJD7383i
PJD7583w/PJD7583wi
DLP Projector
- User Guide
- Guide de l’utilisateur
- Bedienungsanleitung
- Guía del usuario
- Guida dell’utente
- Guia do usuário
- Användarhandbok
- Käyttöopas
- Podręcznik użytkownika
- Pyководство пользователя
- Kullanιcι kιlavuzu
- 使用手冊(繁中)
- 使用手冊 (簡中)
IMPORTANT: Please read this User Guide to obtain important
information on installing and using your product in a safe
manner, as well as registering your product for future service.
Warranty information contained in this User Guide will describe
your limited coverage from ViewSonic Corporation, which is also
found on our web site at http://www.viewsonic.com in English,
or in specific languages using the Regional selection box in the
upper right corner of our website.
“Antes de operar su equipo lea cuidadosamente las
instrucciones en este manual”
- 사용자 안내서
Model No. : VS13339
VS13340
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy, and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
For Canada
• This Class B digital apparatus complies with Canadian ICES-003.
• Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low Voltage Directive
2006/95/EC.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic Equipment Directive
2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment including any spent or
discarded batteries or accumulators as unsorted municipal waste, but use the return and
collection systems available.
If the batteries, accumulators and button cells included with this equipment, display the
chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal content of
more than 0.0005% Mercury or more than, 0.002% Cadmium, or more than 0.004% Lead.
Industry Canada Notice
This wireless module device complies with Canadian RSS-210.To prevent radio interference to the
licensed service, this device is intended to be operated indoors and away from windows to provide
maximum shielding. Equipment (or its transmitting antenna) that is installed outdoors is subject to
licensing. The installer of this radio equipment must ensure that the antenna is located or pointed such
that it does not emit RF field in excess of Health Canada limits for the general population; consult
Safety Code 6, obtainable from Health Canada’s web site www.hc-sc.gc.ca/rpb.
i
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean with a soft, dry cloth.
7. Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
devices (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade and the third prong are provided
for your safety. If the provided plug does not fit into your outlet, consult an electrician
for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs.
Convenience receptacles and the point where they exit from the unit. Be sure that the
power outlet is located near the unit so that it is easily accessible.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the unit. When a cart is used, use caution when
moving the cart/unit combination to avoid injury from tipping over.
13. Unplug this unit when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the unit
has been damaged in any way, such as: if the power-supply cord or plug is damaged,
if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or
moisture, or if the unit does not operate normally or has been dropped.
ii
Declaration of RoHS Compliance
This product has been designed and manufactured in compliance with Directive 2002/95/
EC of the European Parliament and the Council on restriction of the use of certain hazardous
substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply
with the maximum concentration values issued by the European Technical Adaptation
Committee (TAC) as shown below:
Proposed Maximum
Concentration
Actual Concentration
Lead (Pb)
0.1%
< 0.1%
Mercury (Hg)
0.1%
< 0.1%
Cadmium (Cd)
0.01%
< 0.01%
Hexavalent Chromium (Cr6+)
0.1%
< 0.1%
Polybrominated biphenyls (PBB)
0.1%
< 0.1%
Polybrominated diphenyl ethers (PBDE)
0.1%
< 0.1%
Substance
Certain components of products as stated above are exempted under the Annex of the RoHS
Directives as noted below:
Examples of exempted components are:
1. Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in other lamps
not specifically mentioned in the Annex of RoHS Directive.
2. Lead in glass of cathode ray tubes, electronic components, fluorescent tubes, and
electronic ceramic parts (e.g. piezoelectronic devices).
3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or
more lead).
4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium
containing up to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by
weight.
iii
Copyright Information
Copyright © ViewSonic® Corporation, 2010. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of
Microsoft Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks
of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC
are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequential damages resulting from
furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to
change product specifications without notice. Information in this document may change without
notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any
purpose without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes
available, please register your product on the Internet at: www.viewsonic.com. The ViewSonic®
Wizard CD-ROM also provides an opportunity for you to print the registration form, which you
may mail or fax to ViewSonic.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
PJD7383/PJD7383i/PJD7583w/PJD7583wi
ViewSonic DLP Projector
VS13339/VS13340
PJD7383/7383i/7583w/7583wi_UG_ENG
Rev. 1B 09-22-10
_______________________________
_______________________________
The lamp in this product contains mercury which can be dangerous to you and the environment.
Please use care and dispose of in accordance with local, state or federal laws.
ViewSonic respects the environment and is committed to working and living green.
Thank you for being part of Smarter, Greener Computing.
Please visit ViewSonic website to learn more.
1. USA: www.viewsonic.com/company/green/
2. Europe: www.viewsoniceurope.com/uk/support/recycling-information/
3. Taiwan: recycle.epa.gov.tw/recycle/index2.aspx
1
Table of contents
Important safety
instructions .......................3
Introduction......................5
Projector features ................................. 5
Shipping contents................................. 6
Projector exterior view......................... 7
Controls and functions ......................... 8
Positioning your
projector..........................12
Controlling the projector through
a LAN environment ........................... 39
Displaying images through
vsPresenter......................................... 46
Displaying pictures with a USB
storage device .................................... 50
Using the PointBlank pen
(PJD7383i/PJD7583wi only)............. 53
Using the projector in standby
mode .................................................. 57
Shutting down the projector .............. 58
Menu operation.................................. 59
Choosing a location............................ 12
Projection dimensions ........................ 13
Maintenance ...................68
Connection ......................15
Care of the projector .......................... 68
Lamp information .............................. 69
Connecting a computer or monitor .... 16
Connecting Video source devices ...... 17
Playing sound through the projector .. 19
Operation ........................21
Starting up the projector..................... 21
Using the menus................................. 23
Utilizing the password function ......... 24
Switching input signal........................ 26
Adjusting the projected image ........... 27
Magnifying and searching for details. 29
Selecting the aspect ratio ................... 29
Optimizing the image......................... 31
Hiding the image................................ 35
Locking control keys.......................... 35
Freezing the image ............................. 36
Operating in a high altitude
environment ....................................... 36
Creating your own startup screen....... 37
Setting the presentation timer ............ 38
2
Table of contents
Troubleshooting .............75
Specifications ..................76
Projector specifications...................... 76
Dimensions ........................................ 77
Ceiling mount installation ................. 77
Timing chart ...................................... 77
Copyright and Regulation
information .....................79
Appendix.........................80
IR control table .................................. 80
RS232 command table....................... 80
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that you
follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Please read this manual before you operate your projector. Save it for future
reference.
Do not look straight at the projector lens during operation. The intense light beam
may damage your eyes.
Refer servicing to qualified service personnel.
Always open the lens shutter or remove the lens cap when the projector lamp is
on.
In some countries, the line voltage is NOT stable. This projector is designed to operate
safely within a mains voltage between 100 to 240 volts AC, but could fail if power
cuts or surges of 10 volts occur. In areas where the mains voltage may fluctuate
or cut out, it is recommended that you connect your projector through a power
stabilizer, surge protector or uninterruptible power supply (UPS).
Do not block the projection lens with any objects when the projector is under
operation as this could cause the objects to become heated and deformed or even
cause a fire. To temporarily turn off the lamp, press BLANK on the projector or
remote control.
The lamp becomes extremely hot during operation. Allow the projector to cool for
approximately 45 minutes prior to removing the lamp assembly for replacement.
Do not operate lamps beyond the rated lamp life. Excessive operation of lamps
beyond the rated life could cause them to break on rare occasions.
Never replace the lamp assembly or any electronic components unless the projector is
unplugged.
Do not place this product on an unstable cart, stand, or table. The product may fall,
sustaining serious damage.
Do not attempt to disassemble this projector. There are dangerous high voltages inside
which may cause death if you should come into contact with live parts. The only user
serviceable part is the lamp which has its own removable cover.
Under no circumstances should you ever undo or remove any other covers. Refer
servicing only to suitably qualified professional service personnel.
Do not place this projector in any of the following environments.
- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls
and free flow of air around the projector.
- Locations where temperatures may become excessively high, such as the inside of a
car with all windows rolled up.
- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical
components, shortening the projector's life span and darkening the picture.
- Locations near fire alarms
- Locations with an ambient temperature above 40°C / 104°F
- Locations where the altitudes are higher than 3000 m (10000 feet).
Important safety instructions
3
13.
Do not block the ventilation holes. If the ventilation holes are seriously obstructed,
overheating inside the projector may result in a fire.
- Do not place this projector on a blanket, bedding or any other soft surface.
- Do not cover this projector with a cloth or any other item.
- Do not place inflammables near the projector.
14.
Always place the projector on a level, horizontal surface during operation.
- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of
more than 15 degrees front to back. Using the projector when it is not fully horizontal
may cause a malfunction of, or damage to, the lamp.
15.
16.
17.
18.
Do not stand the projector on end vertically. Doing so may cause the projector to fall
over, causing injury or resulting in damage to the projector.
Do not step on the projector or place any objects upon it. Besides probable physical
damage to the projector, doing so may result in accidents and possible injury.
Do not place liquids near or on the projector. Liquids spilled into the projector may
cause it to fail. If the projector does become wet, disconnect it from the power
supply's wall socket and call your local service center to have the projector serviced.
This product is capable of displaying inverted pictures for ceiling mount installation.
Use only qualified ceiling mount kit for mounting the projector and ensure it is
securely installed.
19.
20.
When the projector is under operation, you may sense some heated air and odor from
its ventilation grill. It is a normal phenomenon and not a product defect.
Do not use the Security bar for transporting or installation. It should be used with a
commercially available theft prevention cable.
Safety instructions for ceiling mounting of the
projector
We want you to have a pleasant experience using your projector, so we need to bring this
safety matter to your attention to prevent damage to person and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a
proper fitting projector ceiling mount kit and that you ensure it is securely and safely
installed.
If you use an inappropriate projector ceiling mount kit, there is a safety risk that the
projector may fall from the ceiling due to an improper attachment through the use of the
wrong gauge or length screws.
You can purchase a projector ceiling mount kit from the place you purchased your projector.
We recommends that you also purchase a separate Kensington lock compatible security
cable and attach it securely to both the Kensington lock slot on the projector and the base of
the ceiling mount bracket. This will perform the secondary role of restraining the projector
should its attachment to the mounting bracket become loose.
4
Important safety instructions
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Short throw lens to create larger images with less distance between the projector and the
screen
Presentation timer for better control of time during presentations
PointBlank pen for interactive function (PJD7383i/PJD7583wi only)
LAN Settings allowing management of projector status from a remote compute
LAN display available
USB display supports computer connection via a USB mini-B type to A type cable
Support USB flash drive for JPEG presentation
Support 3D DLP Link
Color management allowing color adjustments to your liking
12V output ready to trigger external device such as an electric screen
Microphone input with 10W speaker
Less then 1W power consumption in standby mode
Screen Color correction allowing projection on surfaces of several predefined colors
Quick auto search speeding up the signal detecting process
Up to 8 sets of picture modes providing multiple choices for different projection
purposes
One-key auto-adjustment to display the best picture quality
Digital keystone correction to correct distorted images
Adjustable color balance control for data/video display
High brightness projection lamp
Ability to display 16.7 million colors
Multi-language On-Screen Display (OSD) menus
Switchable normal and economic modes to reduce the power consumption
Component HDTV compatibility (YPbPr)
PJLink™ compatible
•
The apparent brightness of the projected image will vary depending on the ambient
lighting conditions, selected input signal contrast/brightness settings, and is directly
proportional to projection distance.
•
The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
Introduction
5
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these
items are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those
illustrated.
Projector
Power Cord
VGA Cable
Multi-language user manual
DVD
Quick Start Guide
Remote Control & Battery
PointBlank pen (PJD7383i/
PJD7583wi only)
USB Cable (PJD7383i/
PJD7583wi only)
Optional accessories
1.
2.
3.
6
Ceiling mount
Replacement lamp
Soft carry case
Introduction
Projector exterior view
1.
Front/upper side
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
1
2
3
4
6
7
5
8
Rear/lower side
9
10 11 12 13 14 15 16
17
18 19 20 21 22
18.
DC 12V OUT
19.
20.
23
21.
24
24
22.
25
23.
24.
25.
External control panel
(See "Projector" on page 8 for
details.)
Lamp cover
Vent (heated air exhaust)
Quick-release button
Lens cover
Front IR remote sensor
Focus ring
Projection lens
Kensington anti-theft lock slot
AC power cord inlet
Rear IR remote sensor
RJ45 LAN input port
Mini B USB port
Type A USB port
RS-232 control port
RGB signal output socket
RGB (PC)/Component video
(YPbPr/YCbCr) signal input
socket-1/2
Video input socket/
S-Video input socket
Audio signal input socket (L/R)
Audio signal input socket
Audio signal output socket
Microphone input socket
Connects a microphone with a 3.5
mm mini jack cable or wireless
module.
Security bar
Connects a commercially available
theft prevention cable.
12V DC output terminal
Used to trigger external devices
such as an electric screen or light
control, etc. Consult your dealer for
how to connect these devices.
Rear adjuster foot
Quick-release foot
Warning
•
THIS APPARATUS MUST BE EARTHED.
•
When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring,
or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should
occur during operation of the unit, operate the disconnect device to switch the power supply
off, or disconnect the power plug.
Introduction
7
Controls and functions
Projector
1.
1
2.
3.
2
3
7
4
8
5
9
4
10
6
11
4.
5.
6.
7.
8.
9.
10.
11.
8
Introduction
Focus ring
Adjusts the focus of the projected image.
TEMPerature indicator light
Lights up red if the projector's
temperature becomes too high.
POWER indicator light
Lights up or flashes when the projector is
under operation.
I
I POWER
Toggles the projector between standby
mode and on.
Keystone/Arrow keys ( / Up,
/
Down)
Manually corrects distorted images
resulting from an angled projection.
Left/Blank
Hides the screen picture.
SOURCE
Displays the source selection bar.
LAMP indicator light
Indicates the status of the lamp. Lights up
or flashes when the lamp has developed a
problem.
AUTO
Automatically determines the best picture
timings for the displayed image.
Right/
Activates panel key lock.
When the On-Screen Display (OSD)
menu is activated, the #4, #5, and #9 keys
are used as directional arrows to select the
desired menu items and to make
adjustments.
MENU/EXIT
Turns on the On-Screen Display (OSD)
menu. Goes back to previous OSD menu,
exits and saves menu settings.
MODE/ENTER
Selects an available picture setup mode.
Enacts the selected On-Screen Display
(OSD) menu item.
Remote control
1.
1
13
2.
2
14
15
3
4
3.
4.
16
5
5.
6
17
7
6.
8
18
9
10
19
11
20
7.
12
8.
To use the remote mouse control
keys (Page Up, Page Down,
, and
), see "Using the remote mouse
control" on page 10 for details.
9.
10.
11.
12.
I
I POWER
Toggles the projector between standby
mode and on.
Source selection keys (VGA 1/VGA
2/Video)
Selects an input source for display.
Source
Displays the source selection bar.
/ / /
Selects the desired menu items and
makes adjustments.
ENTER
Enacts the selected On-Screen Display
(OSD) menu item.
Menu/
Turns on the On-Screen Display
(OSD) menu.
Performs the same function as the left
mouse button when the mouse mode is
activated.
Magnify keys (+, -)
Magnifies or reduces the projected
picture size.
Keystone keys ( / )
Manually corrects distorted images
resulting from an angled projection.
Freeze
Freezes the projected image.
Timer
Displays the presentation timer
settings menu.
Mouse
Switches between the normal and
mouse modes.
Page Up, Page Down, , : active
after pressing Mouse. An icon appears
on the screen to indicate the activation
of the mouse mode.
Blank
Hides the screen picture.
Introduction
9
13.
14.
15.
16.
17.
18.
Laser
Emits visible laser pointer light for
presentation purposes.
Page Up/Page Down
Operates your display software program
(on a connected PC) which responds to
page up/down commands (like Microsoft
PowerPoint) when the mouse mode is
activated.
AUTO
Automatically determines the best picture
timings for the displayed image.
Right/
Activates panel key lock.
Exit/
Goes back to previous OSD menu, exits
and saves menu settings.
Performs the same function as the right
mouse button when the mouse mode is
activated.
Volume keys (+, -)
Magnifies or reduces the volume level.
19.
20.
Toggles the projector audio between on and
off.
Color Mode
Selects an available picture setup mode.
Using the remote mouse control
The capability of operating your computer with
the remote control gives you more flexibility
when delivering presentations.
1.
2.
3.
4.
Connect the projector to your PC or
notebook with a USB cable prior to using
the remote control in place of your
computer’s mouse.
Set the input signal to D-Sub / Comp. 1
or D-Sub / Comp. 2.
Press Mouse on the remote control to
switch from the normal mode to the
mouse mode. An icon appears on the
screen to indicate the activation of the
mouse mode.
Perform the desired mouse controls on
your remote control.
•
To move the cursor on the screen,
press / / / .
•
To left-click, press
•
To right-click, press
•
To drag-and-drop, press and hold
ENTER, press / / / to drag.
When it is where you want it, press
ENTER again.
•
To operate your display software
program (on a connected PC) which
responds to page up/down commands
(like Microsoft PowerPoint), press
Page Up/Page Down.
•
To return to the normal mode, press
Mouse again or other keys except for
the mouse related multi-function
keys.
Operating the Laser pointer
The Laser Pointer is a presentation aid for
professionals. It emits red colored light when you
press it and the indicator lights up red.
The laser beam is visible. It is necessary to press
and hold LASER for continuous output.
The laser pointer is not a toy. Parents should be
mindful of the dangers of laser energy and keep
this remote control out of the reach of children.
Do not look into the laser light window or
shine the laser light beam on yourself or
others. See the warning messages on the
back of the remote control prior to using it.
10
Introduction
.
.
Remote control effective range
Infra-Red (IR) remote control sensors are located on the front and the back of the projector.
The remote control must be held at an angle within 30 degrees perpendicular to the
projector's IR remote control sensors to function correctly. The distance between the remote
control and the sensors should not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote control and the IR sensors on the
projector that might obstruct the infra-red beam.
•
Operating the projector from the
front
•
Operating the projector from the
rear
°
15
.+
rox
p
Ap
Appr
o
x. 15
°
Replacing the remote control batteries
1.
2.
3.
To open the battery cover, turn the remote control over to view its back, push on the
finger grip on the cover and slide it in the direction of the arrow as illustrated. The
cover will slide off.
Remove any existing batteries (if necessary) and install two AAA batteries observing
the battery polarities as indicated in the base of the battery compartment. Positive (+)
goes to positive and negative (-) goes to negative.
Refit the cover by aligning it with the base and sliding it back down into position.
Stop when it clicks into place.
•
Avoid leaving the remote control and batteries in an excessive heat or humid environment
like the kitchen, bathroom, sauna, sunroom or in a closed car.
•
Replace only with the same or equivalent type recommended by the battery manufacturer.
•
Dispose of the used batteries according to the manufacturer's instructions and local
environment regulations for your region.
•
Never throw the batteries into a fire. There may be danger of an explosion.
•
If the batteries are dead or if you will not be using the remote control for an extended
period of time, remove the batteries to avoid damage to the remote control from possible
battery leakage.
Introduction
11
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
Your projector is designed to be installed in one of four possible installation locations:
1.
Front Table
Select this location with the projector placed near
the floor in front of the screen. This is the most
common way to position the projector for quick
setup and portability.
2.
Front Ceiling
Select this location with the projector suspended
upside-down from the ceiling in front of the
screen.
Purchase the projector ceiling mount kit from your
dealer to mount your projector on the ceiling.
Set Front Ceiling in the SYSTEM SETUP:
Basic > Projector Position menu after you turn
the projector on.
3.
Rear Ceiling
Select this location with the projector suspended
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the
projector ceiling mounting kit are required for this
installation location.
Set Rear Ceiling in the SYSTEM SETUP: Basic
> Projector Position menu after you turn the
projector on.
4.
Rear Table
Select this location with the projector placed near
the floor behind the screen.
Note that a special rear projection screen is
required.
Set Rear Table in the SYSTEM SETUP: Basic >
Projector Position menu after you turn the
projector on.
12
Positioning your projector
Projection dimensions
Refer to "Dimensions" on page 77 for the center of lens dimensions of this projector before
calculating the appropriate position.
PJD7383/PJD7383i
•
4:3 image on a 4:3 screen
(a)
(b)
(e)
(a)
(f)
(d)
(c)
(c)
(d)
(f)
(e)
•
(b)
16:9 image on a 4:3 screen
(b)
(a)
(a)
(e)
(f)
(d)
(c)
(c)
(d)
(f)
(b)
(e)
(e): Screen
(f): Center of lens
4:3 image
(a) Screen
(b) Projection
(c) Image (d) Vertical
Size
distance [m (inch)]
height
offset
[inch (m)]
[cm (inch)] [cm (inch)]
min.
max.
16:9 image
(b) Projection
distance [m (inch)]
min.
max.
(c) Image
height
[cm (inch)
(d) Vertical
offset
[cm (inch)]
30
(0.8) 0.4 (15) 0.4 (15)
46
(18)
7
(2.7) 0.4 (15) 0.4 (15)
34
(14)
12.6
(5.0)
40
(1.0) 0.5 (19) 0.5 (19)
61
(24)
9
(3.6) 0.5 (19) 0.5 (19)
46
(18)
16.8
(6.6)
50
(1.3) 0.6 (24) 0.6 (24)
76
(30)
11
(4.5) 0.6 (24) 0.6 (24)
57
(23)
21.0
(8.3)
60
(1.5) 0.7 (29) 0.7 (29)
91
(36)
14
(5.4) 0.7 (29) 0.7 (29)
69
(27)
25.1
(9.9)
70
(1.8) 0.9 (34) 0.9 (34)
107
(42)
16
(6.3) 0.9 (34) 0.9 (34)
80
(32)
29.3 (11.6)
80
(2.0) 1.0 (39) 1.0 (39)
122
(48)
18
(7.2) 1.0 (39) 1.0 (39)
91
(36)
33.5 (13.2)
90
(2.3) 1.1 (44) 1.1 (44)
137
(54)
21
(8.1) 1.1 (44) 1.1 (44)
103
(41)
37.7 (14.9)
100 (2.5) 1.2 (49) 1.2 (49)
152
(60)
23
(9.0) 1.2 (49) 1.2 (49)
114
(45)
41.9 (16.5)
120 (3.0) 1.5 (58) 1.5 (58)
183
(72)
27 (10.8) 1.5 (58) 1.5 (58)
137
(54)
50.3 (19.8)
150 (3.8) 1.9 (73) 1.9 (73)
229
(90)
34 (13.5) 1.9 (73) 1.9 (73)
171
(68)
62.9 (24.8)
200 (5.1) 2.5 (97) 2.5 (97)
305 (120) 46 (18.0) 2.5 (97) 2.5 (97)
229
(90)
83.8 (33.0)
250 (6.4) 3.1 (122) 3.1 (122) 381 (150) 57 (22.5) 3.1 (122) 3.1 (122) 286 (113) 104.8 (41.3)
300 (7.6) 3.7 (146) 3.7 (146) 457 (180) 69 (27.0) 3.7 (146) 3.7 (146) 343 (135) 125.7 (49.5)
Positioning your projector
13
PJD7583w/PJD7583wi
•
16:10 image on a 16:10 screen
(b)
(a)
(a)
(e)
(f)
(d)
(c)
(c)
(d)
(f)
(b)
(e)
•
16:10 image on a 4:3 screen
(b)
(a)
(a)
(e)
(f)
(d)
(c)
(c)
(d)
(f)
(b)
(e)
(e): Screen
(f): Center of lens
16:10 image
16:10 image
(a) 16:10
(a) 4:3
(b)
(b)
Screen Size Projection (c) Image (d) Vertical Screen Size Projection (c) Image (d) Vertical
height
offset
height
offset
[inch (m)] distance [m
[inch (m)] distance [m
[cm (inch)] [cm (inch)]
[cm (inch) [cm (inch)]
(inch)]
(inch)]
30
(0.8) 0.32
(12)
40
(16)
2
(0.8)
30
(0.8)
0.3
(12)
38
(15)
3.8
(1.5)
40
(1.0) 0.42
(17)
54
(21)
3
(1.1)
40
(1.0)
0.4
(16)
51
(20)
5.1
(2.0)
50
(1.3) 0.53
(21)
67
(26)
3
(1.3)
50
(1.3)
0.5
(20)
64
(25)
6.4
(2.5)
60
(1.5) 0.63
(25)
81
(32)
4
(1.6)
60
(1.5)
0.6
(23)
76
(30)
7.6
(3.0)
70
(1.8) 0.74
(29)
94
(37)
5
(1.9)
70
(1.8) 0.70
(27)
89
(35)
8.9
(3.5)
80
(2.0) 0.84
(33)
108
(42)
5
(2.1)
80
(2.0) 0.79
(31)
102
(40) 10.2 (4.0)
90
(2.3) 0.95
(37)
121
(48)
6
(2.4)
90
(2.3) 0.89
(35)
114
(45) 11.4 (4.5)
100
(2.5) 1.05
(41)
135
(53)
7
(2.6)
100
(2.5) 0.99
(39)
127
(50) 12.7 (5.0)
120
(3.0) 1.26
(50)
162
(64)
8
(3.2)
120
(3.0) 1.19
(47)
152
(60) 15.2 (6.0)
150
(3.8) 1.58
(62)
202
(79)
10
(4.0)
150
(3.8) 1.49
(59)
191
(75) 19.1 (7.5)
200
(5.1) 2.11
(83)
269 (106)
13
(5.3)
200
(5.1) 1.99
(78)
254 (100) 25.4 (10.0)
250
(6.4) 2.63 (104) 337 (132)
17
(6.6)
250
(6.4) 2.48
(98)
318 (125) 31.8 (12.5)
300
(7.6) 3.16 (124) 404 (159)
20
(7.9)
300
(7.6) 2.98 (117) 381 (150) 38.1 (15.0)
There is 3% tolerance among these numbers due to optical component variations. It is
recommended that if you intend to permanently install the projector, you should physically
test the projection size and distance using the actual projector in situ before you permanently
install it, so as to make allowance for this projector's optical characteristics. This will help you
determine the exact mounting position so that it best suits your installation location.
14
Positioning your projector
Connection
When connecting a signal source to the projector, be sure to:
1.
2.
3.
Turn all equipment off before making any connections.
Use the correct signal cables for each source.
Ensure the cables are firmly inserted.
•
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 6). They are commercially available from electronics stores.
•
The connection illustrations below are for reference only. The rear connecting jacks
available on the projector vary with each projector model.
•
For detailed connection methods, see pages 16-18.
Monitor
Notebook or
desktop computer
A/V device
Microphone
Speakers
(VGA)
(DVI)
1
or
2
3
1
8
4
8
5
6
8 9
7
10
LAN
TYPE B
USB
TYPE A
USB
RS 232
MONITOR OUT
S-VIDEO
AUDIO IN2 (R)
VIDEO
AUDIO IN2 (L)
AUDIO
IN1
AUDIO
OUT
COMPUTER IN1
MIC
COMPUTER IN2
1.
2.
3.
4.
5.
VGA cable
VGA to DVI-A cable
USB cable
Component Video to VGA (D-Sub)
adapter cable
S-Video cable
6.
7.
8.
9.
10.
Video cable
Audio L/R cable
Audio cable
Microphone 3.5 mini jack cable
USB flash drive/USB wireless dongle
Connection
15
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both
IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
• Using a VGA cable
1.
Take the supplied VGA cable and connect one end to the D-Sub output socket of the
computer.
2.
Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER
IN 2 signal input socket on the projector.
• Using a USB cable
1.
Take a USB mini-B type to USB A type cable and connect one end to the A type jack
of the computer.
2.
Connect the other end of the cable to the mini-B jack on the projector.
3.
Press Source to select USB B as the input signal.
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press
FN and the labeled function key simultaneously. Refer to your notebook's documentation to
find your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you
can connect the MONITOR OUT signal output socket on the projector to an external
monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1.
2.
3.
16
Connect the projector to a computer as described in "Connecting a computer" on page
16.
Take a suitable VGA cable (only one supplied) and connect one end of the cable to the
D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable
and connect the DVI end of the cable to the DVI input socket of the video monitor.
Connect the other end of the cable to the MONITOR OUT socket on the projector.
•
The MONITOR OUT output only works when COMPUTER IN 1 or COMPUTER IN 2 is made
to the projector.
•
To use this connection method when the projector is in standby mode, turn on the Active
VGA Out function under the SYSTEM SETUP: Advanced > Standby Settings menu.
Connection
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the
following output sockets:
• Component Video
• S-Video
• Video (composite)
You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:
Best video quality
The best available video connection method is Component Video (not to be confused with
composite Video). Digital TV tuner and DVD players output Component Video natively, so
if available on your devices, this should be your connection method of choice in preference
to (composite) Video.
See "Connecting a Component Video source device" on page 18 for how to connect the
projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video.
If you have both composite Video and S-Video output terminals on your Video source
device, you should elect to use the S-Video option.
See "Connecting an S-Video source device" on page 18 for how to connect the projector to
an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.
See "Connecting a composite Video source device" on page 19 for how to connect the
projector to a composite Video device.
Connection
17
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1.
2.
•
Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3
RCA type connectors to the Component Video output sockets of the Video source
device. Match the color of the plugs to the color of the sockets; green to green, blue to
blue, and red to red.
Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with a
D-Sub type connector) to the COMPUTER IN 1 or COMPUTER IN 2 socket on the
projector.
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
VGA-Component adapter
(ViewSonic P/N: CB-00008906)
•
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket
available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1.
2.
18
Take an S-Video cable and connect one end to the S-Video output socket of the Video
source device.
Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
•
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
•
If you have already made a Component Video connection between the projector and this
S-Video source device using Component Video connections, you need not connect to this
device using an S-Video connection as this makes an unnecessary second connection of
poorer picture quality. See "Connecting Video source devices" on page 17 for details.
Connection
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1.
2.
Take a Video cable and connect one end to the composite Video output socket of the
Video source device.
Connect the other end of the Video cable to the VIDEO socket on the projector.
•
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
•
You need only connect to this device using a composite Video connection if Component
Video and S-Video inputs are unavailable for use. See "Connecting Video source devices"
on page 17 for details.
Playing sound through the projector
You can make use of the projector (mixed mono) speaker in your presentations, and also
connect separate amplified speakers to the AUDIO OUT socket of the projector.
If you have a separate sound system, you will most likely want to connect the audio output
of your Video source device to that sound system, instead of to the mono audio projector.
You can also use a microphone to output the sound through the projector speaker.
Once connected, the audio can be controlled by the projector On-Screen Display (OSD)
menus. See "Audio Settings" on page 66 for details.
The table below describes the connection methods for different devices, and where the
sound is from.
Device
PC/Component Video
Video/S-Video
Audio input port
AUDIO IN 1
AUDIO IN 2 (L/R)
The projector can
play the sound
from...
AUDIO IN 1/MIC
Audio output port
AUDIO OUT
•
•
AUDIO IN 2 (L/R)/MIC
•
AUDIO OUT
Microphone
MIC
MIC
AUDIO IN 1/MIC
AUDIO IN 2 (L/R)/
MIC
AUDIO OUT
The selected input signal determines which sound will be played by the projector speaker,
and which sound will be output from the projector when AUDIO OUT is connected. If you
select a PC signal, the projector can play the sound received from AUDIO IN 1/MIC.
About the microphone input
•
•
If you wish to use a microphone, connect a 3.5 mini jack cable microphone to the
projector.
You can use a wireless microphone as long as a wireless module is attached to the
projector’s microphone input jack and it works well with the associated devices. To
Connection
19
ensure a quality use of the wireless microphone, it is recommended that your
microphone conforms to the specifications listed in the table below.
Signal
Parameter
Min
Type
Max
Transducer Principle
Microphone
•
•
•
•
20
Dynamic
Impedance
300
1K
ohm
Frequency response
600
16k
Hz
There are two ways to adjust microphone volumes.
•
Directly set microphone volume levels in the SYSTEM SETUP: Advanced > Audio
Settings > Microphone Volume menu.
•
Set projector volume levels in the SYSTEM SETUP: Advanced > Audio Settings >
Volume menu, or press Volume keys (+, -) on the remote control. (The projector
volume setting will affect the microphone volume.)
To make the microphone input available when the projector is in standby mode, turn on
the SYSTEM SETUP: Basic > Standby Settings > Microphone menu.
If the microphone is not working, check the volume setting and cable connection.
You might get feedback noise from the microphone when you are too close to the
speaker of the projector. Move the microphone away from the speaker of the projector.
The greater volume you require, the greater distance you need to be away from the
speaker to prevent the noise.
Connection
Operation
Starting up the projector
1.
Plug the power cord into the projector and into a
wall socket. Turn on the wall socket switch
(where fitted). Check that the POWER
indicator light on the projector flashes blue
after power has been applied.
2.
Remove the lens cap. If it is closed, it could
become deformed due to the heat produced by
the projection lamp.
3.
Press II POWER on the projector or remote
control to start the projector. The POWER
indicator light stays blue when the projector is
on.
(If necessary) Rotate the focus ring to adjust the
image clearness.
•
If the projector is still hot from previous activity, it
will run the cooling fan for approximately 90
seconds before energizing the lamp.
•
To maintain the lamp life, once you turn the
projector on, wait at least 5 minutes before turning
it off.
4.
If the projector is activated for the first time,
select your OSD language following the onscreen instructions.
Switch all of the connected equipment on.
5.
LAN
TYPE
USB B
TYPE
USB A
RS
Operation
21
6.
The projector will start to search for input signals. The current input signal being
scanned appears in the upper left corner of the screen. If the projector doesn't detect a
valid signal, the message 'No Signal' will continue to be displayed until an input
signal is found.
You can also press SOURCE on the projector or remote control to select your desired
input signal. See "Switching input signal" on page 26 for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen. Please change to an input signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
See "Timing chart" on page 77 for details.
22
Operation
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.
Below is the overview of the OSD menu.
Main menu icon
Screen Color
Aspect Ratio
Keystone
Position
Phase
H. Size
Zoom
Highlight
Sub-menu
Off
Auto
3D Sync
3D Sync Invert
Color Management
Current input
signal
Status
ENTER
16
0
Go to the
previous page
or to exit.
On
Disable
Analog RGB
MENU Exit
To use the OSD menus, please set them to your familiar language first.
1.
Press MENU/EXIT on the projector or
Menu on the remote control to turn the
OSD menu on.
Screen Color
Aspect Ratio
Keystone
Position
Phase
H. Size
Zoom
3D Sync
3D Sync Invert
Color Management
Analog RGB
2.
3.
Off
Auto
16
0
On
Disable
MENU Exit
English
Front Table
Disable
Disable
Off
ViewSonic
On
MENU Exit
English
Language
Projector Position
Auto Power Off
Blank Timer
Panel Key Lock
Splash Screen
Screen Capture
Message
LAN Control Settings
Standby Settings
Analog RGB
Use / to highlight the SYSTEM
SETUP: Basic menu.
Language
Projector Position
Auto Power Off
Blank Timer
Panel Key Lock
Splash Screen
Screen Capture
Message
LAN Control Settings
Standby Settings
Analog RGB
Press
to highlight
Language and press / to
select a preferred language.
4.
Front Table
Disable
Disable
Off
ViewSonic
On
MENU Exit
Press MENU/EXIT twice* on
the projector or Exit on the
remote control to leave and
save the settings.
*The first press leads you back
to the main menu and the
second press closes the OSD
menu.
: DISPLAY
: SYSTEM SETUP: Basic
: PICTURE
: SYSTEM SETUP: Advanced
: SOURCE
: INFORMATION
Operation
23
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option
for setting up password security. The password can be set through the On-Screen Display
(OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on
page 23.
You will be inconvenienced if you activate the password functionality and subsequently forget
the password. Print this user manual (if necessary) and write the password you used in this
manual, and keep it in a safe place for later use.
Setting a password
1.
2.
3.
4.
5.
Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security
Settings menu. Press MODE/ENTER on the projector or ENTER on the remote
control. The Security Settings page is displayed.
Highlight Power On Lock and select On by pressing / .
As pictured to the right, the four arrow keys ( ,
INPUT NEW PASSWORD
, , ) respectively represent 4 digits (1, 2,
3, 4). According to the password you desire to
set, press the arrow keys to enter six digits for the
password.
Confirm the new password by re-entering the
MENU Back
new password.
Once the password is set, the OSD menu returns to the Security Settings page.
To leave the OSD menu, press MENU/EXIT on the projector or Exit on the remote
control.
•
Once a password has been set, the projector cannot be used unless the correct password
is entered every time the projector is started.
•
The digits being input will be displayed as asterisks on-screen. Write your selected
password down here in this user manual in advance or right after the password is entered
so that it is available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
If you forget the password
If the password function is activated, you will be asked
to enter the six-digit password every time you turn on
Password Error
the projector. If you enter the wrong password, the
Please try again.
password error message as pictured to the right is
displayed lasting for three seconds, and the message
'INPUT PASSWORD' follows. You can retry by
entering another six-digit password, or if you did not
record the password in this user manual, and you absolutely do not remember it, you can use
the password recall procedure. See "Entering the password recall procedure" on page 25 for
details.
If you enter an incorrect password 5 times in succession, the projector will automatically
shut down in a short time.
24
Operation
Entering the password recall procedure
1.
2.
3.
Press and hold AUTO on the projector or remote
control for 3 seconds. The projector will display
a coded number on the screen.
Write down the number and turn off your
projector.
Seek help from the local service center to decode
the number. You may be required to provide
proof of purchase documentation to verify that
you are an authorized user of the projector.
RECALL PASSWORD
Please write down the recall code,
and contact ViewSonic
Customer Center.
Recall code:
0212
MENU Exit
Changing the password
1.
2.
3.
4.
5.
6.
7.
Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security
Settings > Change Password menu.
Press MODE/ENTER on the projector or ENTER on the remote control. The
message 'INPUT CURRENT PASSWORD' is displayed.
Enter the old password.
•
If the password is correct, another message 'INPUT NEW PASSWORD' is
displayed.
•
If the password is incorrect, the password error message is displayed lasting for
three seconds, and the message 'INPUT CURRENT PASSWORD' is
displayed for your retry. You can press MENU/EXIT on the projector or Exit
on the remote control to cancel the change or try another password.
Enter a new password.
Confirm the new password by re-entering the new password.
You have successfully assigned a new password to the projector. Remember to enter
the new password next time the projector is started.
To leave the OSD menu, press MENU/EXIT on the projector or Exit on the remote
control.
The digits being input will be displayed as asterisks on-screen. Write your selected password
down here in this user manual in advance or right after the password is entered so that it is
available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
Disabling the password function
To disable password protection, go back to the SYSTEM SETUP: Advanced > Security
Settings > Power On Lock menu after opening the OSD menu system. Select Off by
pressing
/ . The message 'INPUT PASSWORD' is displayed. Enter the current
password.
•
If the password is correct, the OSD menu returns to the Security Settings page
with 'Off' shown in the row of Power On Lock. You will not have to enter the
password next time you turn on the projector.
•
If the password is incorrect, the password error message is displayed lasting for
three seconds, and the message 'INPUT PASSWORD' is displayed for your
Operation
25
retry. You can press MENU/EXIT on the projector or Exit on the remote
control to cancel the change or try another password.
Though the password function is disabled, you need to keep the old password in hand should
you ever need to re-activate the password function by entering the old password.
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only
display one full screen at a time.
Be sure the Quick Auto Search function in the SOURCE menu is On if you want the
projector to automatically search for the signals.
You can also manually select the desired signal by
pressing one of the source selection keys on the
remote control, or cycle through the available input
signals.
1.
2.
26
Press SOURCE on the projector or remote
control. A source selection bar is displayed.
Press / until your desired signal is
selected and press MODE/ENTER on the
projector or ENTER on the remote control.
Once detected, the selected source information
will be displayed on the screen for seconds. If
there are multiple devices connected to the
projector, repeat steps 1-2 to search for another
signal.
•
The brightness level of the projected image will
change accordingly when you switch between
different input signals. Data (graphic) "PC"
presentations using mostly static images are
generally brighter than "Video" using mostly
moving images (movies).
•
The input signal type effects the options available
for the Color Mode. See "Selecting a picture
mode" on page 31 for details.
•
The native display resolution of this projector is in
a 4:3 aspect ratio. For best display picture results,
you should select and use an input signal which
outputs at this resolution. Any other resolutions
will be scaled by the projector depending upon
the 'aspect ratio' setting, which may cause some
image distortion or loss of picture clarity. See
"Selecting the aspect ratio" on page 29 for details.
Operation
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 2 rear adjuster feet. These
adjusters change the image height and projection angle. To adjust the projector:
1.
Press the quick-release button and lift the
front of the projector. Once the image is
positioned where you want it, release the
quick-release button to lock the foot in
position.
2.
Screw the rear adjuster feet to fine tune the
horizontal angle.
To retract the foot, hold up the projector while
pressing the quick-release button, then slowly
lower the projector. Screw the rear adjuster feet
in a reverse direction.
2
1
2
If the projector is not placed on a flat surface or
the screen and the projector are not
perpendicular to each other, the projected image
becomes trapezoidal. To correct this situation,
see "Correcting keystone" on page 28 for details.
•
Do not look into the lens while the lamp is on.
The strong light from the lamp may cause
damage to your eyes.
•
Be careful when you press the adjuster button
as it is close to the exhaust vent where hot air
comes from.
Auto-adjusting the image
In some cases, you may need to optimize the
picture quality. To do this, press AUTO on the
projector or remote control. Within 3 seconds,
the built-in Intelligent Auto Adjustment
function will re-adjust the values of Frequency
and Clock to provide the best picture quality.
The current source information will be
displayed in the upper left corner of the screen
for 3 seconds.
•
The screen will be blank while AUTO is
functioning.
•
This function is only available when PC
signal (analog RGB) is selected.
Operation
27
Fine-tuning the image clarity
Sharpen the image by rotating the focus ring.
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the height of the projector, you will need to manually
correct it following one of these steps.
• Using the remote control
Press / on the projector or remote control to
display the Keystone correction page. Press
to
correct keystoning at the top of the image. Press
to correct keystoning at the bottom of the image.
• Using the OSD menu
1.
Press MENU/EXIT on the projector or
Menu on the remote control and then press
/ until the DISPLAY menu is
highlighted.
2.
Press
to highlight Keystone and press
MODE/ENTER on the projector or ENTER
on the remote control. The Keystone
correction page is displayed.
3.
Press
to correct keystoning at the top of
the image or press
to correct keystoning at
the bottom of the image.
28
Operation
Press
/
.
Press
/
.
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the
direction arrow keys for navigating the picture.
• Using the remote control
1.
Press Magnify +/- to display the Zoom bar.
2.
Press Magnify + to magnify the center of the
picture. Press the key repeatedly until the
picture size is suitable for your need.
3.
Use the directional arrows ( , , , ) on
the projector or remote control to navigate the
picture.
4.
To restore the picture to its original size, press
AUTO. You can also press Magnify -. When
the key is pressed again, the picture is further
reduced until it is restored to the original size.
• Using the OSD menu
1.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/ until the DISPLAY menu is highlighted.
2.
Press
to highlight Zoom and press MODE/ENTER on the projector or ENTER
on the remote control. The Zoom bar is displayed.
3.
Repeat steps 2-4 in the section of Using the remote control above. Or if you are using
the projector control panel, continue to the following steps.
4.
Press
on the projector repeatedly to magnify the picture to a desired size.
5.
To navigate the picture, press MODE/ENTER on the projector or ENTER on the
remote control to switch to the paning mode and press the directional arrows ( , ,
, ) to navigate the picture.
6.
Use the directional arrows ( , , , ) on the projector or remote control to
navigate the picture.
7.
To reduce size of the picture, press MODE/ENTER on the projector or ENTER on
the remote control to switch back to the zoom in/out functionality, and press AUTO to
restore the picture to its original size. You can also press
repeatedly until it is
restored to the original size.
The picture can only be navigated after the picture is magnified. You can further magnify the
picture while searching for details.
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and
computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input signal.
To change the projected image ratio (no matter what aspect the source is):
1.
2.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/ until the DISPLAY menu is highlighted.
to highlight Aspect Ratio.
Press
Operation
29
3.
Press / to select an aspect ratio to suit the format of the video signal and your
display requirements.
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active
areas. OSD menus can be displayed on those unused black areas.
1.
2.
3.
Auto: Scales an image proportionally to fit the
projector's native resolution in its horizontal
width. This is suitable for the incoming image
which is neither in 4:3 nor 16:9 and you want to
make most use of the screen without altering the
image's aspect ratio.
15:9 picture
4:3: Scales an image so that it is displayed in the
center of the screen with a 4:3 aspect ratio. This
is most suitable for 4:3 images like computer
monitors, standard definition TV and 4:3 aspect
DVD movies, as it displays them without aspect
alteration.
4:3 picture
16:9: Scales an image so that it is displayed in
the center of the screen with a 16:9 aspect ratio.
This is most suitable for images which are
already in a 16:9 aspect, like high definition TV,
as it displays them without aspect alteration.
16:9 picture
4.
30
16:10 (PJD7583w/PJD7583wi only): Scales an
image so that it is displayed in the center of the
screen with a 16:10 aspect ratio. This is most
suitable for images which are already in a 16:10
aspect as it displays them without aspect
alteration.
Operation
16:10 picture
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined
picture modes so that you can choose one to suit
your operating environment and input signal
picture type.
To select an operation mode that suits your need,
you can follow one of the following steps.
•
•
Press MODE/ENTER on the projector or
Color Mode on the remote control repeatedly
until your desired mode is selected.
Go to the PICTURE > Color Mode menu and press
/
to select a desired mode.
Picture modes for different types of signals
The picture modes available for different types of signals are listed below.
PC input signals: D-Sub / Comp. 1/2 (analog RGB)
1.
Brightest mode: Maximizes the brightness of the projected image. This mode is
suitable for environments where extra-high brightness is required, such as using the
projector in well lit rooms.
2.
PC mode: Is designed for presentations under daylight environment to match PC and
notebook coloring.
3.
ViewMatch mode: Switches between high brightness performance and accurate color
performance.
4.
Cinema mode: Is appropriate for playing colorful movies, video clips from digital
cameras or DVs through the PC input for best viewing in a blackened (little light)
environment.
5.
User 1/User 2 mode: Recalls the settings customized based on the current available
picture modes. See "Setting the User 1/User 2 mode" on page 32 for details.
Video input signals: S-Video, Video, D-Sub / Comp. 1/2 (YPbPr)
1.
Brightest mode: Optimized for daylight viewing, with living room level ambient
brightness.
2.
Gaming mode: Suitable for all types of entertainment media, including gaming and
movies.
3.
ViewMatch mode: Switches between high brightness performance and accurate color
performance.
4.
Cinema mode: Is suitable for enjoying dark movies or DVD movies best viewed in a
blackened (little light) home cinema or lounge room environment.
5.
User 1/User 2 mode: Recalls the settings customized based on the current available
picture modes. See "Setting the User 1/User 2 mode" on page 32 for details.
Operation
31
Setting the User 1/User 2 mode
There are two user-definable modes if the current available picture modes are not suitable
for your need. You can use one of the picture modes (except the User 1/User 2) as a starting
point and customize the settings.
1.
2.
3.
4.
Press MENU/EXIT on the projector or Menu on the remote control to open the OnScreen Display (OSD) menu.
Go to the PICTURE > Color Mode menu.
Press / to select User 1 or User 2.
Press
to highlight Reference Mode.
This function is only available when User 1 or User 2 mode is selected up in the Color Mode
sub-menu item.
5.
6.
7.
8.
Press / to select a picture mode that is closest to your need.
Press
to select a sub-menu item to be changed and adjust the value with / .
See Fine-tuning the image quality in user modes below for details.
When all settings have been done, highlight Save Settings and press MODE/ENTER
on the projector or ENTER on the remote control to store the settings.
The confirmation message 'Setting Saved' is displayed.
Using Screen Color
In the situation where you are projecting onto a colored surface such as a painted wall which
may not be white, the Screen Color feature can help correct the projected picture’s colors to
prevent possible color difference between the source and projected pictures.
To use this function, go to the DISPLAY > Screen Color menu and press / to select a
color which is closest to the color of the projection surface. There are several precalibrated
colors to choose from: Whiteboard, Greenboard, and Blackboard.
This function is only available when a PC type input signal is selected.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available
when User 1 or User 2 mode is selected. You can make adjustments to these functions
based on your needs.
Adjusting Brightness
Highlight the PICTURE > Brightness menu and press
/
.
The higher the value, the brighter the image. And the
lower the setting, the darker the image. Adjust this
control so the black areas of the image appear just as
black and that detail in the dark areas is visible.
+30
+50
+70
0
+30
Adjusting Contrast
Highlight the PICTURE > Contrast menu and press
The higher the value, the greater the contrast. Use this
to set the peak white level after you have previously
adjusted the Brightness setting to suit your selected
input and viewing environment.
32
Operation
/
.
-30
Adjusting Color
Highlight the PICTURE > Color menu and press
/
.
Lower setting produces less saturated colors. If the setting is too high, colors on the image
will be overpowering, which makes the image unrealistic.
Adjusting Tint
Highlight the PICTURE > Tint menu and press
/
.
The higher the value, the more reddish the picture becomes. The lower the value, the more
greenish the picture becomes.
Adjusting Sharpness
Highlight the PICTURE > Sharpness menu and press
/
.
The higher the value, the sharper the picture becomes. The lower the value, the softer the
picture becomes.
Adjusting Brilliant Color
Highlight the PICTURE > Brilliant Color menu and press
/
.
This feature utilizes a new color-processing algorithm and system level enhancements to
enable higher brightness while providing truer, more vibrant colors in the projected picture.
It enables a greater than 50% brightness increase in mid-tone images, which are common in
video and natural scenes, so the projector reproduces images in realistic and true colors. If
you prefer images with that quality, select On. If you don’t need it, select Off.
When Off is selected, the Color Temperature function is not available.
Selecting a Color Temperature
Highlight the PICTURE > Color Temperature menu and press
/
.
The options available for color temperature* settings vary according to the signal type
selected.
1.
T1: With the highest color temperature, T1 makes the image appear the most bluish
white than other settings.
2.
T2: Makes images appear bluish white.
3.
T3: Maintains normal colorings for white.
4.
T4: Makes images appear reddish white.
*About color temperatures:
There are many different shades that are considered to be "white" for various purposes. One
of the common methods of representing white color is known as the “color temperature”. A
white color with a low color temperature appears to be reddish white. A white color with a
high color temperature appears to have more blue in it.
Operation
33
Color Management
Only in permanent installations with controlled lighting levels such as boardrooms, lecture
theaters, or home theaters, should color management be considered. Color management
provides fine color control adjustment to allow for more accurate color reproduction, should
you require it.
If you have purchased a test disc which contains various color test patterns and can be used
to test the color presentation on monitors, TVs, projectors, etc., you can project any image
from the disc on the screen and enter the Color Management menu to make adjustments.
To adjust the settings:
1.
Go to the DISPLAY menu and highlight Color Management.
2.
Press MODE/ENTER on the projector or ENTER on the remote control and the
Color Management page is displayed.
3.
Highlight Primary Color and press / to select a color from among Red, Yellow,
Green, Cyan, Blue, or Magenta.
4.
Press
to highlight Hue and press / to select its range. Increase in the range
will include colors consisted of more proportions of its two adjacent colors.
Please refer to the illustration to the right for
how the colors relate to each other.
For example, if you select Red and set its
Yellow
range at 0, only pure red in the projected
GREEN
RED
picture will be selected. Increasing its range
will include red close to yellow and red close
to magenta.
Cyan
Magenta
5.
Press
to highlight Saturation and adjust
its values to your preference by pressing /
BLUE
. Every adjustment made will reflect to the
image immediately.
For example, if you select Red and set its
value at 0, only the saturation of pure red will
be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation
is too high, that color will be overpowering and unrealistic.
6.
7.
8.
9.
34
Press to highlight Gain and adjust its values to your preference by pressing / .
The contrast level of the primary color you select will be affected. Every adjustment
made will reflect to the image immediately.
Repeat steps 3 to 6 for other color adjustments.
Make sure you have made all of the desired adjustments.
Press MENU/EXIT on the projector or Exit on the remote control to exit and save the
settings.
Operation
Hiding the image
In order to draw the audience's full attention to the
presenter, you can use
on the projector or Blank
on the remote control to hide the screen image. Press
any key on the projector or remote control to restore
the image. The word 'BLANK' appears at the lower
right corner of the screen while the image is hidden.
You can set the blank time in the SYSTEM SETUP:
Basic > Blank Timer menu to let the projector
return the image automatically after a period of time
when there is no action taken on the blank screen.
CAUTION
Do not block the projection lens from projecting as this
could cause the blocking object to become heated and
deformed or even cause a fire.
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings from
being changed accidentally (by children, for example). When the Panel Key Lock is on, no
control keys on the projector will operate except
I
I
POWER.
1.
Press
on the projector or remote control, or
go to the SYSTEM SETUP: Basic > Panel
Key Lock menu, and select On by pressing
/ on the projector or remote control.
2.
A confirmation message is displayed. Select
Yes to confirm.
To release panel key lock, press and hold
for 3
seconds on the projector.
You can also use the remote control to enter the
SYSTEM SETUP: Basic > Panel Key Lock menu
and press / to select Off.
•
Keys on the remote control are still functional
when panel key lock is enabled.
•
If you press I POWER to turn off the projector
without disabling panel key lock, the projector will
still be in locked status the next time it is turned
on.
I
Operation
35
Freezing the image
Press Freeze on the remote control to freeze the
image. The word 'FREEZE' will be displayed in the
upper left corner of the screen. To release the
function, press any key on the projector or remote
control.
Even if an image is frozen on the screen, the pictures
are running on the video or other device. If the
connected devices have active audio output, you will
still hear the audio even though the image is frozen on
screen.
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 1500
m–3000 m above sea level, and temperature is between 0°C–35°C.
CAUTION
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature
is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under
such a condition.
To activate the High Altitude Mode:
Notice
1.
Press MENU/EXIT on the projector or Menu on
We recommend you use the High Altitude
mode by selecting it whenever your
the remote control and then press
/ until
environment is higher than 1500 m.
the SYSTEM SETUP: Advanced menu is
Do you want to turn High Altitude Mode
ON?
highlighted.
2.
Press
to highlight High Altitude Mode and
No
Yes
press
/ to select On. A confirmation
message is displayed.
3.
Highlight Yes and press MODE/ENTER on the projector or ENTER on the remote
control.
Operation under "High Altitude Mode" may cause a higher decibel operating noise level
because of increased fan speed necessary to improve overall system cooling and
performance.
If you use this projector under other extreme conditions excluding the above, it may display
auto shut-down symptoms, which is designed to protect your projector from over-heating.
In cases like this, you should switch to High Altitude Mode to solve these symptoms.
However, this is not to state that this projector can operate under any and all harsh or
extreme conditions.
36
Operation
Creating your own startup screen
In addition to selecting the projector preset startup screen from among ViewSonic logo,
Black or Blue screen, you can make your own startup screen that is a picture projected from
your computer or video source.
To create your own startup screen, project the picture you want to use as your startup screen
from either a computer or video source. The rest of the steps are as follows.
1.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/ until the SYSTEM SETUP: Basic menu is highlighted.
2.
Press to highlight Screen Capture and press MODE/ENTER on the projector or
ENTER on the remote control.
3.
A confirmation message is displayed. Press MODE/ENTER on the projector or
ENTER on the remote control again.
4.
The message 'Screen Capturing...' is displayed while the projector is processing the
picture. Please wait.
5.
If the action is successful, you see the message 'Capture Succeeded' on the screen.
The captured picture is saved as Screen Capture.
6.
To view the captured picture displayed as the startup screen, set Screen Capture in
the SYSTEM SETUP: Basic > Splash Screen menu and restart the projector.
In the unlikely event that the capturing action fails, change your target picture.
Operation
37
Setting the presentation timer
Presentation timer can indicate the presentation time on the screen to help you achieve
better time management when giving presentations. Follow these steps to utilize this
function:
1.
2.
Press Timer on the remote control to access the Presentation
Timer menu, or go to the SYSTEM SETUP: Advanced >
Presentation Timer menu and press MODE/ENTER on the
projector or ENTER on the remote control to display the
Presentation Timer page.
Highlight Timer Period and decide the time period by pressing
/ . The length of time can be set from 1 to 5 minutes in 1minute increments and 5 to 240 minutes in 5-minute increments.
If the timer is already on, the timer will restart whenever the Timer Period is reset.
3.
Press
to highlight Timer Display and choose if you want the timer to show up on
the screen by pressing / .
Selection
Description
Displays the timer on screen throughout the presentation
Always
time.
1 min/2 min/3 min Displays the timer on screen in the last 1/2/3 minute(s).
Never
Hides the timer throughout the presentation time.
4.
Press
to highlight Timer Position and set the timer position by pressing
Top-Left
5.
7.
8.
38
Top-Right
.
Bottom-Right
Press to highlight Timer Counting Direction and select your desired counting
direction by pressing / .
Selection
Count Up
Count Down
6.
Bottom-Left
/
Description
Increases from 0 to the preset time.
Decreases from the preset time to 0.
Press
to highlight Sound Reminder and decide if you want to activate sound
reminder by pressing / . If you select On, a double beep sound will be heard at
the last 30 seconds of counting down/up, and a triple beep sound will be produced
when the timer is up.
To activate the presentation timer, press and press / to highlight On and press
MODE/ENTER on the projector or ENTER on the remote control.
A confirmation message displays. Highlight Yes and press MODE/ENTER on the
projector or ENTER on the remote control to confirm. You will see the message
“Timer is On” displaying on the screen. The timer starts counting when the timer is
on.
Operation
Controlling the projector through a LAN
environment
You can manage and control the projector from one or more remote computers when they
are properly connected to the same local area network.
Internet
Cable/ADSL
modem
Wired LAN connection
If you are in a DHCP environment:
1.
2.
3.
4.
5.
6.
7.
8.
Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector
and the other end to the RJ45 port on your Ethernet or router.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/ until the SYSTEM SETUP: Basic menu is highlighted.
Press to highlight LAN Control Settings and press MODE/ENTER on the
projector or ENTER on the remote control. The LAN Control Settings page is
displayed.
Highlight Wired LAN and press MODE/ENTER on the projector or ENTER on the
remote control.
Make sure the Status is Connect.
Press to highlight DHCP and press / to select On.
Press to highlight Apply and press MODE/ENTER on the projector or ENTER
on the remote control.
Please wait for around 15 - 20 seconds, and then re-enter the Wired LAN page. The
IP Address, Subnet Mask, Default Gateway, and DNS settings will be displayed.
Note down the IP address displayed in the IP Address row.
•
If the Projector IP Address still does not appear, contact your network administrator.
•
If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default
Gateway, and DNS settings will display 0.0.0.0. Make sure the cables are properly
connected and perform the procedures above again.
•
If you wish to connect to the projector in its standby mode, be sure you have selected
RJ45 and obtained the IP Address, Subnet Mask, Default Gateway, and DNS information
when the projector is on.
If you are in a non-DHCP environment:
1.
2.
3.
Repeat steps 1-5 above.
Press to highlight DHCP and press / to select Off.
Contact your ITS administrator for information on the IP Address, Subnet Mask,
Default Gateway, and DNS settings.
Operation
39
4.
5.
6.
7.
Press to select the item you want to modify and press MODE/ENTER on the
projector or ENTER on the remote control.
Press / to move the cursor and the press / to enter the value.
To save the settings, press MODE/ENTER on the projector or ENTER on the remote
control. If you do not want to save the settings, press MENU/EXIT on the projector
or Exit on the remote control.
Press to highlight Apply and press MODE/ENTER on the projector or ENTER
on the remote control.
•
If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, Default
Gateway, and DNS settings will display 0.0.0.0. Make sure the cables are properly
connected and perform the procedures above again.
•
If you wish to connect to the projector in its standby mode, be sure you have selected
RJ45 and obtained the IP Address, Subnet Mask, Default Gateway, and DNS information
when the projector is on.
Wireless LAN connection
To connect to the projector wirelessly, you have to plug a ViewSonic wireless dongle
(optional) to the USB Type A connector on the projector, and then only a few OSD
configuration steps are required.
1.
2.
Make sure the projector is turned on.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/ until the SYSTEM SETUP: Basic menu is highlighted.
3.
Press to highlight LAN Control Settings and press MODE/ENTER on the
projector or ENTER on the remote control. The LAN Control Settings page is
displayed.
4.
Highlight Wireless LAN Status and press MODE/ENTER on the projector or
ENTER on the remote control.
5.
Check the information displayed on the menu.
You can change the wireless settings on the Network Control > Administrator Login >
Network Setup page. To access the page, see page 42 for details.
About AP and Infrastructure modes
In AP mode, you need to use your computer’s wireless connection utility to search for the
projector’s SSID and connect to it. Then you can search for the projector with vsPresenter.
In Infrastructure mode, you should connect both your computer and projector to the same
AP router and make connections with the IP address.
The following diagram describes how to access the Internet in AP and Infrastructure
modes.
(AP mode)
(Infrastructure mode)
Internet
Internet
40
Operation
If you need more information about AP and Infrastructure modes, please refer to user
documentations for Wireless Routers which are usually available on 3C stores.
Resetting the network settings
If you encounter a malfunctiom of network connection and need to reset the network
settings, you can go into the SYSTEM SETUP: Basic > LAN Control Settings >
Network Reset menu to return the network settings to default values.
If you want to return the network settings to default values and reset the passwords for the
network related software, press +SOURCE+MODE/ENTER on the projector control
panel.
Controlling the projector through a web browser
Once you have the correct IP address for the projector and the projector is on or in standby
mode, you can use any computer that is on the same local area network to control the
projector.
•
If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher.
•
The screen shots in this manual are for reference only, and may differ from the actual
design.
1.
Enter the address of the projector in the address bar of your browser and press Enter.
2.
The main page of the Network Control appears.
3
5
6
4
3.
4.
5.
To change the language for the web pages, click the down arrow (v) to reveal a drop
down list and select a desired language.
To download vsPresenter, click Download. See "Displaying images through
vsPresenter" on page 46 for details.
The Crestron (eControl) page displays the Crestron eControl user interface. See
"About Crestron control" on page 42 for details.
Operation
41
6.
To have access to the Administrator page, you need to enter a password. The default
password is “0000”.
•
System Status: Displays the system information.
•
General Setup: Allows you to turn on/off the projector, switch the input signal
for the projector, and change the password for the Administrator page.
•
Picture Setup/Image Setup: Provides some OSD menu items for adjusting the
projected pictures. See "Menu operation" on page 59 for details.
•
Alert Setup/Mail Setup: Allows you to setup the mail server and send system
error messages to your ITS administrator.
•
Network Setup: Provides wired and wireless network settings.
•
Reset to Default: Allows you to restore the device to the factory default settings.
About Crestron control
The eControl page provides a variety of virtual keys to control the projector or adjust the
projected pictures.
i
ii
You can
press / to
reveal more
buttons.
42
Operation
i
i
iii
i. These buttons function the same as the ones on the OSD menus or
remote control. See "2. PICTURE menu" on page 64 and "Projector" on
page 8 for details.
ii. To switch between input signals, click on your desired signal.
iii. The software is available in multiple languages.
•
The Menu button can also be used to go back to previous OSD menus, exit and save menu
settings.
•
The source list varies according to the connectors available on the projector.
•
When you use the projector control panel or remote control to change the OSD menu
settings, it may take a while for the web browser to synchronize these changes with the
projector.
The tools page allows you to manage the projector, configure the LAN control settings and
secure access of remote network operation on this projector.
iv
v
vii
vi
viii
ix
x
iv. This section is only used with the Crestron Control System. Please
contact Crestron or refer to its user manual for setup information.
v. You can name the projector, keep track of its location and the person in
charge of it.
vi. You can adjust the LAN Control Settings.
vii. Once set, access to the remote network operation on this projector has
been password-protected.
viii.Once set, access to the tools page has been password-protected.
•
To prevent errors, only input the English alphabet and digits on the tools page.
•
After making the adjustments, press the Send button and the data will be saved for the
projector.
ix. Press Exit to go back to the remote network operation page.
x. The software is available in multiple languages, though only English
letters and digits are allowed to be input.
Operation
43
Please pay attention to the limitation of input length (including space and other punctuation
keys) in the list blow:
Category Item
Crestron Control
Projector
Network Configuration
User Password
Admin Password
Input Length
Maximum Number of
Characters
IP Address
15
IP ID
2
Port
5
Projector Name
10
Location
9
Assigned To
9
DHCP (Enabled)
(N/A)
IP Address
15
Subnet Mask
15
Default Gateway
15
DNS Server
15
Enabled
(N/A)
New Password
20
Confirm
2
Enabled
(N/A)
New Password
20
Confirm
20
The info page displays the information and status of this projector.
Press exit to
go back to the
remote network
operation page.
After pressing the button “Contact IT Help”, the HELP DESK window will appear in the
upper right corner of the screen. You will be able to deliver messages to RoomView™
software administrators/users who connect to the same local area network.
Please only deliver the messages in English letters and digits.
44
Operation
For more information, visit http://www.crestron.com & www.crestron.com/getroomview.
**Crestron RoomView
On the “Edit Room” page, enter the IP Address (or hostname) as shown on the projector’s
on-screen display (OSD) menu, and “02” for IPID, “41794” for the reserved Crestron
control port.
About Crestron RoomView setting and command method, please access below website to
get RoomView User Guide and more information:
http://www.crestron.com/features/roomview_connected_embedded_projectors_devices/
resources.asp
Operation
45
Displaying images through vsPresenter
Downloading and installing vsPresenter
The vsPresenter is an application running on the host PC. It helps connect your computer to
an available network projector and transfer the desktop content to the network projector via
local network connection.
1.
2.
3.
4.
5.
Enter the main page of Network Control. See steps 1-2 on page 41 for details.
Download vsPresenter.
When the download is complete, install the software to your computer by clicking the
exe file. Follow the on-screen instructions to complete the installation.
If you see the following dialog box, give a name to your computer. The name will
show on the vsPresenter Management. See page 49 for details.
Launch vsPresenter.
Using vsPresenter
1
7
6
4 & 5
2
3
1.
The Search page allows you to search and connect to a projector.
•
To connect to a projector, do the following:
i.
46
Operation
Type the projector IP address.
ii.
iii.
If you want to project your computer screen after connection, click
Directly. If you want to connect to the projector via Network Control
system, click Connect to webpage. The main page of Network Control
will be displayed after connection.
Click Connect.
•
To search for projectors, simply click Search to list all the projectors on the
same local area network. Click the desired projector in the Search result list, and
click Connect directly. You can also type a desired projector name and click
Search.
•
If you are the first time user, choose your identity as a Normal user or
Administrator. Both require no password. But if you choose to be an
Administrator, you have the authority to set a password for connecting to the
projector. That password should be kept and used next when you try to connect
to the same projector.
•
If there are multiple computers connected to the projector, you can decide a
display zone by clicking 1, 2, 3, 4, L, R, All, or Background.
2.
If you want to freeze the projected image on the screen, press
3.
movements will be not been seen on the screen until
You can choose a capture mode from here.
. Any further
is pressed.
•
To display a full screen, click FullScreen.
•
To display a partial screen, click FixedSize. A square appears on your screen.
You can place it where you want to project. If you wish to change the square,
click Alterable.
Operation
47
4.
5.
48
The Basic Setting page allows you to configure vsPresenter.
•
To allow notification messages to appear, click Yes. Click Apply.
•
The Software Information is available on this page.
The Advanced Setting page allows you to configure vsPresenter.
•
To adjust the image quality, click the down arrow to reveal a drop-down list and
select a desired quality level. The higher image quality you select, the higher
network transfer speed is required. Select a YUV sample format between
YUV444 and YUV420. Compared to format YUV420, format YUV 444
provides better effect but may slow the transport and playing speed. Click Apply
after your selections.
•
To adjust the capture rate, move the slider. The network bandwidth may also
affect the performance.
Operation
6.
You can manage the connected projectors listed under Device Management.
•
Under a conference mode:
1. Only the administrator can take control.
2. A projector can display up to 4 computer screens.
•
You can set the name of your computer under vsPresenter Management.
•
For details about the icons, please see the following:
Icon
Description
Icon
Description
You are a normal user and
have no access to change
the password.
Disconnects from the
projector.
You are an administrator
and have authority to
change the password.
Opens the web page of the
Network Control.
You are the user of the
projector.
There is another user of the
projector.
You are an administrator of
the projector.
You are a normal user of the
projector.
Sets a display zone for the projector.
7.
Disconnect
To disconnect from the projector(s), click the Disconnect icon.
Be sure to turn off other virtual network control programs before using vsPresenter.
Operation
49
Displaying pictures with a USB storage device
The projector is built-in an application which can display packaged images on a USB
storage device. It can eliminate the need for a computer source.
The projector supports the following image formats:
File format
Maximum pixel size
JPEG
10000 x 10000
GIF/TIFF/PNG/BMP
1280 x 800
•
Progressive JPEG files are not supported.
•
Some JPEG files may not be displayed clearly.
To display the images on a USB storage device:
1.
2.
3.
4.
Plug the USB storage device into the Type A USB socket.
The projector automatically displays the main screen. Or your can manually select
USB A from the source selection bar.
Press MODE/ENTER on the projector or ENTER on the remote control to display
the content of your USB storage device.
Folders and supported files are represented in thumbnail mode.
•
To scroll through the thumbnails, use the four directional arrow keys.
•
To open a folder/file, press MODE/ENTER or ENTER.
•
To go back to the previous screen, select the thumbnail with an up arrow in the
top right corner of the screen, and press MODE/ENTER or ENTER.
•
To obtain more functions, press AUTO to open the menu. To leave the menu,
press MODE/ENTER or ENTER again.
When viewing thumbnails
Next
50
Operation
Previous
Thumbnail
NameOrder
EXIF OFF
PathDisp OFF
•
Next: Selects the next folder/image.
•
Previous: Selects the previous folder/image.
•
Thumbnail/Full Screen/SlideShow: Displays the selected image in thumbnail/
Full Screen/SlideShow mode.
•
NameOrder/ExtendOrder/SizeOrder/TimeOrder: Sets the images to be
displayed in the order of filenames, filename extension, file sizes, or time the
photos were taken.
•
EXIF OFF/EXIF ON: Sets whether to display the image in EXIF format.
•
PathDisp OFF/PathDisp ON: Sets whether to display the folder’s path.
When viewing slide shows
Stop
Fast
Slide Right
Repeat On
•
Stop/Next/Previous: Stops the slide show/Displays the next image/Displays the
previous image.
•
Fast/Medium/Slow: Sets the interval between the two images display.
•
Slide Right/Slide Up/Right down/Random: Sets the way the slide show is
displayed.
•
Repeat On/Off: Sets whether to repeat the slide shows.
When viewing full screen images
Full Screen
Actual Size
EXIFDisp OFF
Rotate +90
Rotate -90
•
Thumbnail/Full Screen/SlideShow: Displays the selected image in thumbnail/
Full Screen/SlideShow mode.
•
Best Fit/Actual Size: Sets the display size of the image.
•
EXIFDisp OFF/EXIFDisp ON: Sets whether to display the EXIF data.
Operation
51
•
Rotate + 90: Rotates the image 90 degrees clockwise.
•
Rotate -90: Rotates the image 90 degrees counterclockwise.
•
USB 2.0 compliant USB storage media (Mass Storage Class) is supported.
•
It is strongly recommended to use an AC power adaptor with the USB hard disk.
•
The following formats are recommended for the USB hard disk: FAT12/FAT16/FAT32 (NTFS
format is not supported).
•
Some USB flash drives may not work correctly with the projector.
•
The security USB flash drive is not supported.
•
Do not connect any apparatus other than USB storage devices and other equipment for
battery charge through USB. It may caused malfunction.
•
The projector plays up to 200 files in a folder.
•
The filenames are displayed in the following order: symbols, digits, letters.
•
The projector can display the filenames up to 16 characters including the file extension.
•
The application is best to display the filenames in English. If the files are named in other
languages, the filenames may not show properly, but the content still can be displayed.
•
Folders in the USB storage device can be recognized up to 3 layers. The priority of
thumbnail display for image files is as follows:
A
File display priority in folder: A > B > C > D > E > F.
: Current directory: A
Folder G: Cannot be displayed because it is in the 4th
layer.
B : Folder B
D : Folder D
E
C
: Folder C
F
•
52
: Folder E
G
: Folder G
: Folder F
Response time may vary depending on image contents when switching pages, loading
and playing files.
Operation
Using the PointBlank pen (PJD7383i/PJD7583wi
only)
The PointBlank pen can work in place of your regular computer mouse. Just hold the pen in
your hand, and point it at the projected image to point, click, and drag. It gives you more
flexibility to operate your computer without standing next to it.
Preparations
1.
Connect the projector and your computer with a VGA cable, and a USB cable.
LAN
TYPE B
USB
TYPE A
USB
RS 232
MONITOR OUT
S-VIDEO
AUDIO IN2 (R)
VIDEO
AUDIO IN2 (L)
AUDIO
IN1
AUDIO
OUT
COMPUTER IN1
MIC
COMPUTER IN2
2.
3.
4.
Turn on your computer and the PointBlank-compatible projector. Make sure the
projector is displaying the computer’s screen.
Enable the pen by selecting “Yes” in the SOURCE > PointBlank > Enabled menu.
The pen’s link light starts to blink.
Point the pen at the screen to point, click, and drag. Observe the pen’s light. It should
blink at a slower pace when it links to the projector.
Overview of the PointBlank pen
Tip
Sensor
Right mouse button
Left mouse button
Middle button
Link light
Battery light
USB connector
Reset button
Using the PointBlank pen
Hold the pen the way you hold a remote control or a pen.
More settings are available on the SOURCE > PointBlank menu.
You can adjust the click speed of your pen with the Click Speed menu to make it response
faster or slower to meet your needs.
Operation
53
If there are multiple projectors, you can set a channel with the Link Channel menu to
differentiate between projectors and communicate with the pen.
To meet the needs of left-handers and right-handers, you can set your handwriting mode on
the Handwriting Mode menu. When selecting User for the mode, you need to further
adjust the pointer’s Horizontal and Vertical positions.
You can change the function of the Middle button with the M Button menu. If you want to
annotate during Microsoft PowerPoint slide shows, do the following:
1.
2.
3.
Set PwrPnt Annotate
Click the middle button to show a red dot.
Click the left mouse button or click the pen’s tip against the projection surface to draw
or write.
4.
To turn off the annotation function, click the middle button. The red dot changes back
to a normal pointer.
To use the Interactive software, you need to install the provided Interactive software
(included on a disc) to your computer, select Interactive Software on the M Button menu,
and then click the middle button to activate it.
•
If the pen is far away from the screen, be sure to press the left mouse button to click and
drag.
•
When the PointBlank pen is activated, the 3D Sync and Color Mode menus are not
available.
•
Avoid standing too far from the screen. The closer you are to the screen, the better
performance the pen has.
•
Avoid shadows! The pen cannot work if its tip is in a shadow or it is pointing at a shadow.
Using the quick menu
1.
2.
3.
Simply click the middle button to activate the quick menu.
Rotate the middle button to select a desired function.
To perform the selected function, click the middle button again.
Charging the battery
1.
54
To charge the battery, open the flap on the back of the pen to expose the USB
connector.
Operation
2.
Take a USB cable, and connect the smaller end to the pen and the larger end to a
computer. Make sure the computer is powered on.
3.
The battery light stays amber while the battery is charging. When charging is finished,
the battery lights off. You can disconnect the USB cable or keep it connected.
Do not use the pen while the pen is in charging. A full battery charge takes 4-7 hours
and will allow 20-50 hours non-stop use.
Do not disassemble the pen yourself. Refer all servicing to your dealer.
The lithium battery is only rechargeable, and is not user serviceable or user
replaceable.
4.
5.
6.
Troubleshooting PointBlank
1.
2.
If the pen doesn’t work at all, or it works intermittently, try one of these solutions:
•
Try holding down one of the pen’s buttons while moving the pen.
•
Press the tip, L, or R button on the pen to turn it on.
•
If the pen’s green Link light never blinks, then the pen’s battery is fully
discharged; connect the pen to your computer by using a USB cable.
•
Make sure the pen is not pointing at a shadow or its tip is not in a shadow.
•
If the room is brightly lit, reduce the room illumination.
•
Point the pen away from the screen while using the computer’s mouse.
•
If someone is using a different pen with the same projector, they must stop using
it before you can use your own.
•
Change the value in the SOURCE > PointBlank > Link Channel menu.
•
Reset the pen by pushing the end of a paper clip into the reset opening on the
pen.
If the mouse pointer is in the wrong place on the screen, or the mouse pointer’s
movement is restricted to only part of the screen, try one of these solutions:
•
Make sure your projector is displaying the computer’s screen and not some
other source (such as DVD, VCR, etc.). To change the source, press the Source
button on the projector or its remote control.
Operation
55
•
3.
If the battery light does not turn on when the pen is being charged, try one of the
following:
•
56
Make sure the projector is displaying the same image as the computer’s main or
built-in monitor (don’t extend your desktop into multiple monitors.)
Operation
Make sure a USB cable is connected between the pen and your computer. And
your computer is powered on.
Using the projector in standby mode
Some of the projector functions are available in standby mode (plugged in but not turned
on). To use these functions, be sure you have turned on the corresponding menus under
SYSTEM SETUP: Basic > Standby Settings, and the cable connections are correctly
made. For the connection methods, see the Connection chapter.
LAN Control
Select On when you wish to control the projector over a network when it is in standby
mode.
Microphone
Select On when you wish to use a microphone in standby mode. Be sure you have adjusted
the SYSTEM SETUP: Advanced > Audio Settings > Microphone Volume menu to a
desired level before the projector is turned off.
Active VGA Out
Selecting On outputs a VGA signal when the COMPUTER IN 1 and COMPUTER OUT
sockets are correctly connected to devices. The projector outputs the signal received only
from COMPUTER IN 1.
Active Audio Out
Selecting On outputs an audio signal when the AUDIO IN 1 and AUDIO OUT sockets are
correctly connected to devices. The projector outputs the audio signal received only from
AUDIO IN 1.
Operation
57
Shutting down the projector
1.
Press II POWER and a confirmation message
is displayed prompting you.
If you don't respond in a few seconds, the
message will disappear.
2.
3.
Press II POWER a second time.
Disconnect the power cord from the wall
socket if the projector will not be used in an
extended period of time.
CAUTION
58
•
To protect the lamp, the projector will not respond
to any commands during the cooling process.
•
Do not unplug the power cord before the projector
shutdown sequence is complete.
Operation
LAN
TYPE
USB B
TYPE
USB A
RS
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type
selected.
The menu items are available when the projector detects at least one valid signal. If there is
no equipment connected to the projector or no signal detected, limited menu items are
accessible.
Main menu
Sub-menu
Screen Color
Aspect Ratio
1.
DISPLAY
Keystone
Position
Phase
H. Size
Zoom
3D Sync
3D Sync Invert
Options
Off/Whiteboard/Greenboard/
Blackboard
• Auto/4:3/16:9
(PJD7383/PJD7383i only)
• Auto/4:3/16:9/16:10
(PJD7583w/PJD7583wi
only)
TI 3D DLP Link/Off
Disable/Invert
R/G/B/C/M/Y
Primary Color
Hue
Saturation
Gain
PC source: Brightest/PC/ViewMatch/Cinema/User
1/User 2
Color Mode
Video source: Brightest/Gaming/ViewMatch/
Cinema/User 1/User 2
PC source: Brightest/PC/ViewMatch/Cinema
Reference Mode Video source: Brightest/Gaming/ViewMatch/
Cinema
Brightness
Contrast
Color
Tint
Sharpness
Brilliant Color
On/Off
Color Temperature
T1/T2/T3/T4
Save Settings
Color
Management
2.
PICTURE
Operation
59
Main menu
Sub-menu
Quick Auto Search
Enabled
PointBlank
Click Speed
Fast/Medium/Slow
Link Channel
Auto/1/2/3/.../28
Lefthand 1/Lefthand 2/
Righthand 1/Righthand 2/User
Handwriting
Mode
Horizontal
Vertical
3. SOURCE (PJD7383i/
PJD7583wi
only)
M Button
60
Operation
Options
On/Off
Yes/No
Normal/Draw
Alt-Tab
Alt-Esc
Command-Tab
Left Mouse
Right Mouse
Middle Mouse
Double Click
PwrPnt Annotate
Interactive Software
Main menu
Sub-menu
Options
Language
Projector Position
Front Table/Rear Table/Rear
Ceiling/Front Ceiling
Auto Power Off
Disable/5 min/10 min/20 min/
30 min/40 min/50 min/60 min
Blank Timer
Disable/5 min/10 min/15 min/
20 min/25 min/30 min
Panel Key Lock
On/Off
Splash Screen
Black/Blue/ViewSonic/Screen
Capture/Off
Screen Capture
Message
On/Off
4.
SYSTEM
SETUP:
Basic
Status
Connect/
Disconnect
DHCP
On/Off
IP Address
Wired LAN
Subnet Mask
Default
Gateway
LAN Control
Settings
DNS
Apply
Status
Wireless LAN
Status
(Read only)
Standby
Settings
Connect/
Disconnect
SSID
IP Address
Connection
Mode
LAN Control
On/Off
Microphone
On/Off
Active VGA Out
On/Off
AP/
Infrastructure
Active Audio Out On/Off
Operation
61
Main menu
Sub-menu
Options
High Altitude Mode
On/Off
DCR
On/Off
Mute
Audio Settings
On/Off
Volume
Microphone Volume
Menu Settings
5.
SYSTEM
SETUP:
Advanced
Menu Display
Time
5 sec/10 sec/15 sec/20 sec/25
sec/30 sec
Menu Position
Center/Top-Left/Top-Right/
Bottom-Left/Bottom-Right
Closed Caption
Closed Caption Enable
Caption Version
Lamp Mode
Lamp Settings
On/Off
CC1/CC2/CC3/CC4
Normal/Economic
Reset Lamp Timer
Equivalent Lamp Hour
Presentation
Timer
Timer Period
1~240 minutes
Timer Display
Always/1 min/2 min/3 min/
Never
Timer Position
Top-Left/Bottom-Left/TopRight/Bottom-Right
Timer Counting
Direction
Count Down/Count Up
Sound Reminder On/Off
On/Off
Security
Settings
Change Password
Power On Lock
Reset All Settings
6.
Current System Status
INFORMATION
62
Operation
On/Off
On/Off
• Source
• Color Mode
• Resolution
• Color System
• Equivalent Lamp Hour
• MAC Address
Description of each menu
Function
Description
the projected picture’s color when the projection surface
Screen Color Corrects
is not white. See "Using Screen Color" on page 32 for details.
Aspect Ratio
Keystone
Position
Phase
There are three options to set the image's aspect ratio depending
on your input signal source. See "Selecting the aspect ratio" on
page 29 for details.
Corrects any keystoning of the image. See "Correcting keystone"
on page 28 for details.
Displays the position adjustment page. To move the projected
image, use the directional arrow keys. The values shown on the
lower position of the page change with every key press you made
until they reach their maximum or minimum.
Adjusts the clock phase to reduce image
distortion.
1. DISPLAY menu
H. Size
Adjusts the horizontal width of the image.
Zoom
Magnifies or reduces the projected image. See "Magnifying and
searching for details" on page 29 for details.
This projector features a 3D function which enables you to enjoy
the 3D movies, videos, and sporting events in a more realistic
way by presenting the depth of the images.
You need to wear a pair of 3D glasses to view the 3D images.
• TI 3D DLP Link:
Enables projector for TI 3D DLP Link.
3D Sync
• Off:
Disables 3D.
When the 3D Sync function is on:
•
The brightness level of the projected image will decrease.
•
The Color Mode cannot be adjusted.
•
The Keystone can only be adjusted within limited degrees.
•
The Zoom can only magnify the pictures to limited sizes.
•
And the input signal is 120Hz, the PointBlank menu is not
available.
3D Sync
Invert
When you discover the inversion of the image depth, enable this
function to correct the problem. (For TI 3D DLP Link only)
Color
Management
See "Color Management" on page 34 for details.
Operation
63
Function
Color Mode
Reference
Mode
Brightness
Contrast
2. PICTURE menu
Color
Tint
Sharpness
Brilliant
Color
Description
Pre-defined picture modes are provided so you can optimize
your projector image set-up to suit your program type. See
"Selecting a picture mode" on page 31 for details.
Selects a picture mode that most suits your need for the image
quality and further fine-tune the image based on the selections
listed on the same page below. See "Setting the User 1/User 2
mode" on page 32 for details.
Adjusts the brightness of the image. See "Adjusting Brightness"
on page 32 for details.
Adjusts the degree of difference between dark and light in the
image. See "Adjusting Contrast" on page 32 for details.
Adjusts the color saturation level -- the amount of each color in a
video image. See "Adjusting Color" on page 33 for details.
Adjusts the red and green color tones of the image. See
"Adjusting Tint" on page 33 for details.
The function is only available when Video or S-Video with
NTSC system is selected.
Adjusts the image to make it look sharper or softer. See
"Adjusting Sharpness" on page 33 for details.
Adjusts white peaking while maintaining correct color
presentation. See "Adjusting Brilliant Color" on page 33 for
details.
Color
See "Selecting a Color Temperature" on page 33 for details.
Temperature
3. SOURCE
menu
64
Save
Settings
Saves the settings made for the User 1 or User 2 mode.
Quick Auto
Search
See "Switching input signal" on page 26 for details.
PointBlank
See "Using the PointBlank pen (PJD7383i/PJD7583wi only)" on
page 53 for details.
Operation
Function
Language
Projector
Position
Auto Power
Off
4. SYSTEM SETUP: Basic menu
Blank Timer
Description
Sets the language for the On-Screen Display (OSD) menus. See
"Using the menus" on page 23 for details.
The projector can be installed on a ceiling or behind a screen, or
with one or more mirrors. See "Choosing a location" on page 12
for details.
Allows the projector to turn off automatically if no input signal
is detected after a set period of time. See "Setting Auto Power
Off" on page 69 for details.
Sets the image blank time when the Blank feature is activated,
once elapsed the image will return to the screen. See "Hiding the
image" on page 35 for details.
Panel Key
Lock
Disables or enables all panel key functions except II POWER
on the projector and keys on the remote control. See "Locking
control keys" on page 35 for details.
Splash
Screen
Allows you to select which logo screen will be displayed during
projector start-up.
Screen
Capture
Captures and stores the projected picture as Screen Capture.
See "Creating your own startup screen" on page 37 for details.
Message
Selecting On displays the current information on the screen
when the projector is detecting or searching for a signal.
LAN Control
Settings
See "Controlling the projector through a LAN environment" on
page 39 for details.
Standby
Settings
See "Using the projector in standby mode" on page 57 for
details.
5. SYSTEM SETUP: Advanced menu
High Altitude A mode for operation in high altitude areas. See "Operating in a
high altitude environment" on page 36 for details.
Mode
DCR
Enables or disables the DCR (Dynamic Contrast Ratio) function.
Selecting On enables the function and the projector will
automatically switch the lamp mode between normal and
economic modes according to the input image detected.
This function is only available when a PC source is in use.
After enabling DCR, frequent lamp mode switching may
shorten lamp life and noise level will vary during operation.
Operation
65
Function
Description
The sound adjustments made as below will have an effect on the
projector speaker. Be sure you have made a correct connection to
the projector audio input/output jacks. See "Connection" on page
15 and "Playing sound through the projector" on page 19 for
more details.
Audio
Settings
Mute
Mutes the sound received from AUDIO IN 1 and AUDIO IN 2
(L/R). It will not affect the microphone sound level.
5. SYSTEM SETUP: Advanced menu
Volume
Adjusts the sound level received from AUDIO IN 1 and AUDIO
IN 2 (L/R).
Menu
Settings
Microphone Volume
Adjusts the microphone sound level.
Menu Display Time
Sets the length of time the OSD will remain active after your last
key press. The range is from 5 to 30 seconds in 5-second
increments.
Menu Position
Sets the On-Screen Display (OSD) menu position.
Closed Caption Enable
Activates the function by selecting On when the selected input
signal carries closed captions.
•
Closed
Caption
Captions: An on-screen display of the dialogue, narration,
and sound effects of TV programs and videos that are closed
captioned (usually marked as "CC" in TV listings).
This function is only available when a Composite video or
S-Video input signal is selected and its system format is
NTSC.
Caption Version
Selects a preferred closed captioning mode. To view captions,
select CC1, CC2, CC3, or CC4 (CC1 displays captions in the
primary language in your area).
66
Operation
Function
Description
Lamp Mode
See "Setting Lamp Mode as Economic" on page 69 for details.
5. SYSTEM SETUP: Advanced menu
Lamp
Settings
Reset Lamp Timer
See "Resetting the lamp timer" on page 73 for details.
Presentation
Timer
See "Setting the presentation timer" on page 38 for details.
Security
Settings
See "Utilizing the password function" on page 24 for details,
Reset All
Settings
Equivalent Lamp Hour
See "Getting to know the lamp hour" on page 69 for details on
how the total lamp hour is calculated.
Returns all settings to the factory preset values.
The following settings will still remain: Phase, H. Size, User
1, User 2, Language, Projector Position, High Altitude
Mode, Security Settings.
Source
Shows the current signal source.
6. INFORMATION menu
Color Mode
Shows the selected mode in the PICTURE menu.
Current
System
Status
Resolution
Shows the native resolution of the input signal.
Color System
Shows input system format, NTSC, PAL, SECAM, or RGB.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used.
MAC Address
Shows the MAC Address of your projector.
MAC Address stands for Media Access Control Address,
which is a physical layer address used to uniquely identify
a network node.
Operation
67
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is
to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts
need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
•
•
Use a canister of compressed air to remove dust.
If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens
cleaner and gently wipe the lens surface.
CAUTION
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as
described in "Shutting down the projector" on page 58 and unplug the power cord.
•
•
To remove dirt or dust, wipe the case with a soft, lint-free cloth.
To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
CAUTION
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
•
•
•
•
Make sure the temperature and humidity of the storage area are within the
recommended range for the projector. Please refer to "Specifications" on page 76 or
consult your dealer about the range.
Retract the adjuster feet.
Remove the battery from the remote control.
Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent.
68
Maintenance
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically
calculated by the built-in timer.
To obtain the lamp hour information:
1.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/ until the SYSTEM SETUP: Advanced menu is highlighted.
2.
Press to highlight Lamp Settings and press MODE/ENTER on the projector or
ENTER on the remote control. The Lamp Settings page is displayed.
3.
You will see the Equivalent lamp hour information on the menu.
4.
To leave the menu, press MENU/EXIT on the projector or Exit on the remote
control.
You can also get the lamp hour information on the INFORMATION menu.
Extending lamp life
The projection lamp is a consumable item. To keep the lamp life as long as possible, you
can do the following settings via the OSD menu.
Setting Lamp Mode as Economic
Using Economic mode reduces system noise and power consumption by 20%. If the
Economic mode is selected, the light output will be reduced and result in darker projected
pictures.
Setting the projector in Economic mode also extends the lamp operation life. To set
Economic mode, go into the SYSTEM SETUP: Advanced > Lamp Settings > Lamp
Mode menu and press / .
Setting Auto Power Off
This function allows the projector to turn off automatically if no input source is detected
after a set period of time to prevent unnecessary waste of lamp life.
To set Auto Power Off, go into the SYSTEM SETUP: Basic > Auto Power Off menu and
press / . If the preset time lengths are not suitable for your presentation, select Disable.
The projector will not automatically shut down in a certain time period.
Maintenance
69
Timing of replacing the lamp
When the Lamp indicator lights up red or a message appears suggesting it is time to
replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
CAUTION
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too
hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator
still lights up after turning the power back on, please contact your dealer. See "Indicators" on
page 74 for details.
The following lamp warning displays will remind you to change the lamp.
Status
Message
Install a new lamp for optimal performance. If the
projector is normally run with Economic selected
(See "Setting Lamp Mode as Economic" on page
69), you may continue to operate the projector
until the next hour lamp warning appears.
Notice
Order Replacement Lamp
Lamp > ____ Hours
OK
A new lamp should be fitted to avoid the
inconvenience when the projector runs out of lamp
time.
Notice
Replace Lamp Soon
Lamp > ____ Hours
OK
It is strongly recommended that you replace the
lamp at this age. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished. If the lamp is not
replaced beforehand, it must be replaced when
you see this message.
The lamp MUST be replaced before the projector
will operate normally.
Notice
Replace Lamp Now
Lamp > ____ Hours
Lamp usage time exceeded
OK
Notice
Lamp usage time exceeded
Replace lamp (refer to User Manual)
Then reset lamp timer
OK
70
Maintenance
Replacing the lamp
To prepare a new lamp, contact your dealer and tell the lamp type number.
Type number: RLC-057
WARNING
Hg - Lamp contains mercury. Manage in accordance with local disposal
laws. See www.lamprecycle.org
•
To reduce the risk of electrical shock, always turn the projector off and disconnect the
power cord before changing the lamp.
•
To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes
before replacing the lamp.
•
To reduce the risk of injuries to fingers and damage to internal components, use caution
when removing lamp glass that has shattered into sharp pieces. Before replacing the
lamp, clean the lamp compartment and dispose of cleaning materials. Be careful of sharp
edges in the lamp compartment. Wash hands after lamp replacement.
•
Only ViewSonic certified lamps are tested with this projector. Use of other lamps may
cause electrical shock and fire.
1.
2.
3.
Turn the power off and disconnect the
projector from the wall socket. If the
lamp is hot, avoid burns by waiting for
approximately 45 minutes until the
lamp has cooled.
Loosen the screws that secure the lamp
cover on the both sides of the projector
until the lamp cover loosens.
Remove the lamp cover from the
projector.
1
WARNING
•
Do not turn the power on with the lamp
cover removed.
•
Do not insert your fingers between the
lamp and the projector. The sharp edges
inside the projector may cause injuries.
4.
5.
6.
2
Remove and dispose of the lamp
protection film.
Pull out the lamp connector from a slot
in the lamp compartment. Disconnect it
from the projector as illustrated.
Loosen the screw that secures the lamp.
1
3
2
1
Maintenance
71
7.
Lift the handle so that it stands up. Use
the handle to slowly pull the lamp out
of the projector.
CAUTION
•
Pulling it too quickly may cause the lamp
to break and scatter broken glass in the
projector.
•
Do not place the lamp in locations where
water might splash on it, children can
reach it, or near flammable materials.
•
Do not insert your hands into the projector
after the lamp is removed. If you touch the
optical components inside, it could cause
color unevenness and distortion of the
projected images.
8.
Insert the new lamp into the lamp
compartment and make sure it fits in
the projector.
Reconnect the lamp connector and
place it back into its slot to be flush
with the projector.
9.
10.
Tighten the screw that secures the lamp.
CAUTION
•
Loose screw may cause a bad connection,
which could result in malfunction.
•
Do not over tighten the screw.
11.
Ensure the handle is fully laid flat and
locked in place.
12.
Place the lamp protection film supplied
with the new lamp on the lamp
compartment.
Replace the lamp cover on the
projector.
13.
2
2
1
72
Maintenance
14.
Tighten the screws that secure the lamp
cover.
CAUTION
•
Loose screw may cause a bad connection,
which could result in malfunction.
•
Do not over tighten the screws.
15.
Restart the projector.
CAUTION
Do not turn the power on with the lamp cover removed.
Resetting the lamp timer
16.
17.
18.
19.
After the startup logo, open the On-Screen
Display (OSD) menu.
Go to the SYSTEM SETUP: Advanced >
Lamp Settings menu. Press MODE/ENTER
on the projector or ENTER on the remote
control. The Lamp Settings page is
displayed.
Press to highlight Reset lamp timer and
press MODE/ENTER on the projector or
ENTER on the remote control. A warning
message is displayed asking if you want to
reset the lamp timer.
Highlight Reset and press MODE/ENTER
on the projector or ENTER on the remote
control. The lamp time will be reset to '0'.
Notice
Reset Lamp Timer?
Reset
Cancel
CAUTION
Do not reset if the lamp is not new or replaced as this
could cause damage.
Maintenance
73
Indicators
Light
Power
Temp
Status & Description
Lamp
Power events
Blue
Flashing
Off
Off
Stand-by mode
Blue
Off
Off
Blue
Off
Off
Powering up
Normal operation
Lamp events
Purple
Flashing
Off
Red
Off
Off
Red
The projector has shut down automatically. If you try to restart the projector, it will shut down again. Please contact
your dealer for assistance.
1.
The projector needs 90 seconds to cool down. Or
2.
Please contact your dealer for assistance.
Thermal events
74
Off
Red
Off
Off
Red
Red
Green
Off
Red
Red
Red
Red
Red
Red
Green
Blue
Red
Red
Blue
Red
Green
Purple
Red
Red
Purple
Red
Green
Off
Green
Red
Maintenance
The projector has shut down automatically. If you try to restart the projector, it will shut down again. Please contact
your dealer for assistance.
Troubleshooting
The projector does not turn on.
Cause
Remedy
There is no power from the power
cord.
Plug the power cord into the AC inlet on the
projector, and plug the power cord into the
power outlet. If the power outlet has a switch,
make sure that it is switched on.
Attempting to turn the projector on
again during the cooling process.
Wait until the cooling down process has
completed.
No picture
Cause
Remedy
The video source is not turned on or
connected correctly.
Turn the video source on and check that the
signal cable is connected correctly.
The projector is not correctly
connected to the input signal device.
Check the connection.
The input signal has not been
correctly selected.
Select the correct input signal with the
SOURCE key on the projector or remote
control.
The lens cover is still closed.
Open the lens cover.
Blurred image
Cause
Remedy
The projection lens is not correctly
focused.
Adjust the focus of the lens using the focus
ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as
well as the height of the projector if necessary.
The lens cover is still closed.
Open the lens cover.
Remote control does not work
Cause
Remedy
The battery is out of power.
Replace the battery with a new one.
There is an obstacle between the
remote control and the projector.
Remove the obstacle.
You are too far away from the
projector.
Stand within 8 meters (26 feet) of the
projector.
Troubleshooting
75
Specifications
Projector specifications
All specifications are subject to change without notice.
General
Product name
PJD7383/PJD7383i
PJD7583w/PJD7583wi
1024 x 768 XGA
1-CHIP DMD
F = 2.6, f = 6.9 mm
210 W lamp
1280 x 800 WXGA
Optical
Resolution
Display system
Lens F/Number
Lamp
Electrical
Power supply
Power consumption
AC100–240V, 3.29 A, 50/60 Hz (Automatic)
329 W (Max); < 1 W (Standby)
Mechanical
Weight
3.5 Kg (7.7 lbs)
Input terminal
Computer input
RGB input
Video signal input
S-VIDEO
VIDEO
SD/HDTV signal input
Audio signal input
USB port
D-Sub 15-pin (female) x 2
Mini DIN 4-pin port x 1
RCA jack x 1
Analog – D-Sub <–> Component RCA jack x 3
(through RGB input)
PC audio jack x 1/RCA audio jack (L/R) x 1
Microphone x 1
Type A x 1; Mini B x 1
Output terminal
RGB output
Speaker
DC 12 V (Max. 1A)
D-Sub 15-pin (female) x 1
10 watt x 1 (Amp approx. 10 w)
Control terminal
RS-232 serial control
LAN
IR receiver x 2
9 pin x 1
RJ45 x 1
Environmental Requirements
Operating temperature
Operating relative humidity
Operating altitude
76
Specifications
0°C–40°C at sea level
10%–90% (without condensation)
• 0–1499 m at 0°C–35°C
• 1500–3000 m at 0°C–30°C (with High Altitude Mode
on)
Dimensions
290 mm (W) x 126 mm (H) x 254 mm (D)
290
254
126
61
72
Ceiling mount installation
84
149.5
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
14.04
228
Unit: mm
Timing chart
Supported timing for PC input
Resolution
720 x 400
640 x 480
800 x 600
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel
Frequency
(MHz)
Mode
31.469
31.469
37.861
37.5
43.269
24.688
61.91
37.879
48.077
46.875
53.674
30.998
77.425
70.087
59.94
72.809
75
85.008
49.673
119.518
60.317
72.188
75
85.061
49.916
119.854
28.3221
25.175
31.5
31.5
36
19.75
52.5
40
50
49.5
56.25
30.75
83
720 x 400_70
VGA_60
VGA_72
VGA_75
VGA_85
VGA_50
VGA_120
SVGA_60
SVGA_72
SVGA_75
SVGA_85
SVGA_50
SVGA_120
Specifications
77
1024 x 768
1280 x 800
1280 x 960
1440 x 900
1400 x 1050
1600 x 1200
640 x 480@67Hz
832 x 624@75Hz
1024 x 768@75Hz
1152 x 870@75Hz
48.363
56.476
60.023
68.667
39.634
98.958
49.702
62.795
71.554
60
85.938
55.935
65.317
75
35
49.722
60.241
68.68
60.004
70.069
75.029
84.997
49.98
119.804
59.81
74.934
84.88
60
85.002
59.887
59.978
60
66.667
74.546
75.02
75.06
65
75
78.75
94.5
52
137.75
83.5
106.5
122.5
108
148.5
106.5
121.75
162
30.24
57.28
80
100
XGA_60
XGA_70
XGA_75
XGA_85
XGA_50
XGA_120
WXGA_60
WXGA_75
WXGA_85
1280 x 960_60
1280 x 960_85
WXGA+_60
SXGA+_60
UXGA
MAC13
MAC16
MAC19
MAC21
Supported timing for Component-YPbPr input
Signal Format
Horizontal Frequency
(kHz)
Vertical Frequency (Hz)
480i(525i)@60Hz
480p(525p)@60Hz
576i(625i)@50Hz
576p(625p)@50Hz
720p(750p)@60Hz
720p(750p)@50Hz
1080i(1125i)@60Hz
1080i(1125i)@50Hz
1080P@60Hz
1080P@50Hz
15.73
31.47
15.63
31.25
45.00
37.50
33.75
28.13
67.5
56.26
59.94
59.94
50.00
50.00
60.00
50.00
60.00
50.00
60
50
Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image
vibration.
Supported timing for Video and S-Video inputs
78
Video mode
Horizontal
Frequency (kHz)
Vertical Frequency
(Hz)
Color sub-carrier
Frequency (MHz)
NTSC
PAL
SECAM
PAL-M
PAL-N
PAL-60
NTSC4.43
15.73
15.63
15.63
15.73
15.63
15.73
15.73
60
50
50
60
50
60
60
3.58
4.43
4.25 or 4.41
3.58
3.58
4.43
4.43
Specifications
Copyright and Regulation information
Copyright
Copyright 2010. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic Corporation makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Further, ViewSonic Corporation
reserves the right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or changes.
*DLP and Digital Micromirror Device (DMD) are trademarks of Texas Instruments. Others
are copyrights of their respective companies or organizations.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by ViewSonic Corporation may void
authority to operate the equipment.
Copyright and Regulation information
79
Appendix
IR control table
Key
format
Power
NEC
Byte1 Byte2 Byte3 Byte4
83
F4
17
Freeze
NEC
83
F4
03
fc
Up
NEC
83
F4
0b
f4
Down
NEC
83
F4
0c
f3
Left
NEC
83
F4
0e
f1
Right/Key Lock
NEC
83
F4
0f
f0
Color Mode
NEC
83
F4
10
ef
Volume+
NEC
83
F4
21
DE
Volume-
NEC
83
F4
22
DD
Auto/Page Down
NEC
83
F4
08
f7
Source/Page Up
NEC
83
F4
04
fb
Blank
NEC
83
F4
07
f8
Menu/Mouse L key
NEC
83
F4
30
CF
Magnify +
NEC
83
F4
18
e7
Magnify -
NEC
83
F4
19
e6
Enter
NEC
83
F4
15
ea
D7
E8
Exit/Mouse R key
NEC
83
F4
28
Mute
NEC
83
F4
14
eb
VGA1
NEC
83
F4
41
be
VGA2
NEC
83
F4
45
ba
Video
NEC
83
F4
52
ad
Keystone +
NEC
83
F4
09
F6
Keystone -
NEC
83
F4
0a
F5
Mouse
NEC
83
F4
31
CE
Timer
NEC
83
F4
27
d8
RS232 command table
<Pin assignment for this two end>
80
Pin
Description
Pin
Description
1
NC
2
RX
3
TX
4
NC
5
GND
6
NC
7
RTSZ
8
CTSZ
9
NC
Appendix
<Interface>
RS-232 protocol
Baud Rate
115200 bps (default)
Data Length
8 bit
Parity Check
None
Stop Bit
1 bit
Flow Control
None
Function
Status
Write
Power
Read
Reset
cmd
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D
Turn off
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E
Power
status
(on/off)
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 0x5E
Execute
Write
Splash
Screen
Read
High
Altitude
Mode
Action
Turn on
Write
Read
Write
Lamp Mode
Read
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F
Splash
Screen
Black
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x00 0x67
Splash
Screen Blue
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x01 0x68
Splash
Screen
ViewSonic
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x02 0x69
Splash
Screen
Screen
Capture
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x03 0x6A
Splash
Screen Off
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x04 0x6B
Splash
Screen
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0A 0x68
High
Altitude
Mode Off
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x00 0x69
High
Altitude
Mode On
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x01 0x6A
High
Altitude
Mode status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0C
0x6A
Lamp Mode
Normal
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x00 0x6D
Lamp Mode
Economic
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x01 0x6E
Lamp Mode
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x10 0x6E
status
Appendix
81
Write
Message
Read
Write
Projector
Position
Read
Write
3D Sync
Read
Write
3D Sync
Invert
Read
Write
Contrast
Read
Brightness
Write
Read
Aspect ratio
Write
Read
Auto Adjust
Horizontal
position
Appendix
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x00 0x84
Message
On
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x01 0x85
Message
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x27 0x85
Front Table
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E
Rear Table
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F
Rear
Ceiling
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60
Front
Ceiling
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61
projector
position
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00 0x5F
OFF
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x00 0x7E
TI 3D DLP
Link
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x01 0x7F
3D Sync
Status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x20 0x7F
Off
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x00 0x7F
On
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x01 0x80
3D Sync
Invert
Status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x21 0x80
Contrast
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x00 0x60
Contrast
increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x01 0x61
Contrast
ratio
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x02 0x61
Brightness
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x00 0x61
Brightness
increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x01 0x62
Brightness 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x03 0x62
Aspect ratio
Auto
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62
Aspect ratio
4:3
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64
Aspect ratio
16:9
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65
Aspect ratio
16:10
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66
Aspect ratio 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x04 0x63
Execute
Write
Read
82
Message
Off
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x05 0x00 0x63
Horizontal
position
shift right
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x01 0x65
Horizontal
position
shift left
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x00 0x64
Horizontal
position
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x06 0x65
Write
Vertical
position
Read
Write
Color
temperature
Read
Blank
Write
Read
KeystoneVertical
Write
Read
Write
Color mode
Read
Primary
Color
Write
Read
Vertical
position
shift up
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x00 0x65
Vertical
position
shift down
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x01 0x66
read
Vertical
position
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x07 0x66
color
temperature
T1
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x00 0x66
color
temperature
T2
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x01 0x67
color
temperature
T3
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x02 0x68
color
temperature
T4
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x03 0x69
color
temperature 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x08 0x67
status
Blank on
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 0x68
Blank off
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x00 0x67
Blank status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09 0x68
Decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68
Increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69
Keystone
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A 0x69
Brightest
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69
Cinema
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x01 0x6A
User 1
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x02 0x6B
User 2
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x03 0x6C
PC/Gaming
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x04 0x6D
ViewMatch
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x05 0x6E
Preset
mode status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0B
0x6A
Primary
color R
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x00 0x6E
Primary
color G
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x01 0x6F
Primary
color B
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x02 0x70
Primary
color C
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x03 0x71
Primary
color M
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x04 0x72
Primary
color Y
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x05 0x73
Primary
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x10 0x6F
color status
Appendix
83
Hue
Write
Read
Saturation
Write
Read
Gain
Write
Read
Write
Freeze
Read
Source
input
Write
Read
Write
Quick Auto
Search
Read
Mute
Write
Read
Volume
Write
Read
84
Appendix
Hue
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x00 0x6F
Hue
increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x01 0x70
Hue
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x11 0x70
Saturation
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x00 0x70
Saturation
increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x01 0x71
Saturation
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x12 0x71
Gain
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x00 0x71
Gain
increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x01 0x72
Gain
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x13 0x72
Freeze on
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60
Freeze off
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x00 0x5F
Freeze
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x00 0x60
Input
source VGA
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60
Input
source
VGA2
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x08 0x68
Input
source
Composite
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65
Input
source
SVIDEO
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x06 0x66
Source
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x01 0x61
Quick Auto
Search on
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x01 0x62
Quick Auto
Search off
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x00 0x61
Quick Auto
Search
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x02 0x62
status
Mute on
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x01 0x61
Mute off
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x00 0x60
Mute status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x00 0x61
Increase
Volume
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x01 0x00 0x61
Decrees
Volume
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x02 0x00 0x62
Volume
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x03 0x64
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 0x66
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68
Language
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69
Write
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x09 0x6A
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0a 0x6B
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0b 0x6C
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0c 0x6D
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0d 0x6E
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0e 0x6F
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0f 0x70
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x10 0x71
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x11 0x72
Read
Language
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x00 0x62
Write
Reset Lamp
usage hour
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x01 0x00 0x62
Read
Lamp
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x01 0x63
usage hour
Read
Read error
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x0D
0x66
Disable
PointBlank
0x6 0x14 0x00 0x04 0x00 0x34 0x0C 0x2C 0x00 0x84
Enable
PointBlank
0x6 0x14 0x00 0x04 0x00 0x34 0x0C 0x2C 0x01 0x85
PointBlank
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x2C
0x85
Lamp Time
Error status
Write
PointBlank
Read
Appendix
85
Customer Support
For technical support or product service, see the table below or contact your reseller.
Note : You will need the product serial number.
Country/Region
Website
Australia/New
Zealand
www.viewsonic.com.au
Canada
www.viewsonic.com
Europe
Hong Kong
India
Ireland (Eire)
www.viewsoniceurope.
com
www.hk.viewsonic.com
www.in.viewsonic.com
www.viewsoniceurope.
com/uk/
www.kr.viewsonic.com
T = Telephone
F = FAX
AUS= 1800 880 818
NZ= 0800 008 822
T (Toll-Free)= 1-866-463-4775
T (Toll)= 1-424-233-2533
F= 1-909-468-3757
Email
service@au.viewsonic.com
service.ca@viewsonic.com
www.viewsoniceurope.com/uk/Support/Calldesk.htm
T= 852 3102 2900
T= 1800 11 9999
www.viewsoniceurope.com/uk/
support/call-desk/
T= 080 333 2131
service@hk.viewsonic.com
service@in.viewsonic.com
service_ie@
viewsoniceurope.com
service@kr.viewsonic.com
Korea
Latin America
www.viewsonic.com/la/ T= 0800-4441185
soporte@viewsonic.com
(Argentina)
Latin America
www.viewsonic.com/la/ T= 1230-020-7975
soporte@viewsonic.com
(Chile)
Latin America
www.viewsonic.com/la/ T= 01800-9-157235
soporte@viewsonic.com
(Columbia)
Latin America
www.viewsonic.com/la/ T= 001-8882328722
soporte@viewsonic.com
(Mexico)
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS
Electroser, Av Reforma No. 403Gx39 y 41, 97000 Mérida, Yucatán. Tel: 01.999.925.19.16
Other places please refer to http://www.viewsonic.com/la/soporte/index.htm#Mexico
Latin America
www.viewsonic.com/la/ T= 0800-54565
soporte@viewsonic.com
(Peru)
Macau
www.hk.viewsonic.com T= 853 2870 0303
service@hk.viewsonic.com
Middle East
ap.viewsonic.com/me/
Contact your reseller
service@ap.viewsonic.com
T= 1-800-688-6688 (English)
Puerto Rico &
service.us@viewsonic.com
www.viewsonic.com
T= 1-866-379-1304 (Spanish)
Virgin Islands
soporte@viewsonic.com
F= 1-909-468-3757
Singapore/
www.ap.viewsonic.com T= 65 6461 6044
service@sg.viewsonic.com
Malaysia/Thailand
South Africa
ap.viewsonic.com/za/
Contact your reseller
service@ap.viewsonic.com
www.viewsoniceurope. www.viewsoniceurope.com/uk/ service_gb@
United Kingdom
com/uk/
support/call-desk/
viewsoniceurope.com
T (Toll-Free)= 1-800-688-6688
United States
www.viewsonic.com
T (Toll)= 1-424-233-2530
service.us@viewsonic.com
F= 1-909-468-3757
86
Limited Warranty
VIEWSONIC® PROJECTOR
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship during
the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components.
Limited Three (3) year General Warranty
Subject to the more limited one (1) year warranty set out below, North and South America: Three (3) years
warranty for all parts excluding the lamp, three (3) years for labor, and one (1) year for the original lamp from
the date of the first consumer purchase; Europe except Poland: Three (3) years warranty for all parts excluding
the lamp, three (3) years for labor, and ninety (90) days for the original lamp from the date of the first consumer
purchase; Poland: Two (2) years warranty for all parts excluding the lamp, two (2) years for labor, and ninety (90)
days for the original lamp from the date of the first consumer purchase.
Limited One (1) year Heavy Usage Warranty:
Under heavy usage settings, where a projector’s use includes more than fourteen (14) hours average daily
usage, North and South America: One (1) year warranty for all parts excluding the lamp, one (1) year for
labor, and ninety (90) days for the original lamp from the date of the first consumer purchase; Europe: One
(1) year warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the original
lamp from the date of the first consumer purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic office for the warranty
information.
Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s installed
lamp only. All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration, failure, or malfunction resulting from:
a.Accident, abuse, misuse, neglect, fire, water, lightning, or other acts of nature, improper
maintenance, unauthorized product modification, or failure to follow instructions supplied with
the product.
b. Operation outside of product specifications.
c.Operation of the product for other than the normal intended use or not under normal conditions.
d. Repair or attempted repair by anyone not authorized by ViewSonic.
e. Any damage of the product due to shipment.
f. Removal or installation of the product.
g. Causes external to the product, such as electric power fluctuations or failure.
h. Use of supplies or parts not meeting ViewSonic’s specifications.
i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.
3. Removal, installation, and set-up service charges.
87
How to get service:
1. For information about receiving service under warranty, contact ViewSonic Customer Support
(please refer to “Customer Support” page). You will need to provide your product’s serial number.
2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name,
(c) your address, (d) a description of the problem, and (e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service
center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein
including the implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not
be liable for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience,
loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill,
interference with business relationships, or other commercial loss, even if advised of the possibility
of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of state law:
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state. Some states do not allow limitations on implied warranties and/or do not allow the exclusion of
incidental or consequential damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada,
contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan Excluded) is
subject to the terms and conditions of the Maintenance Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in www.viewsoniceurope.
com under Support/Warranty Information.
4.3: Projector Warranty
88
PRJ_LW01 Rev. 1h 06-25-07
Mexico Limited Warranty
®
VIEWSONIC PROJECTOR
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the
warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic
will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include
remanufactured or refurbished parts or components & accessories.
How long the warranty is effective:
3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of the first consumer purchase.
Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s installed lamp only.
All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a.Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification,
unauthorized attempted repair, or failure to follow instructions supplied with the product.
b.Any damage of the product due to shipment.
c.Causes external to the product, such as electrical power fluctuations or failure.
d. Use of supplies or parts not meeting ViewSonic’s specifications.
e. Normal wear and tear.
f. Any other cause which does not relate to a product defect.
3.Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is
displayed on the product for an extended period of time.
4.Removal, installation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the
attached Customer Support page). You will need to provide your product’s serial number, so please record the product
information in the space provided below on your purchase for your future use. Please retain your receipt of proof of
purchase to support your warranty claim.
For Your Records
Model Number: __________________________
Product Name: ________________________
Document Number: ____________________
Serial Number: ___________________________
Purchase Date: ________________________
Extended Warranty Purchase? _______________(Y/N)
If so, what date does warranty expire? _________
1.To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c)
your address, (d) a description of the problem, and (e) the serial number of the product.
2.Take or ship the product in the original container packaging to an authorized ViewSonic service center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein including the
implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:
1.Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of
the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business
relationships, or other commercial loss, even if advised of the possibility of such damages.
2.Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
89
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: disc2@hmo.megared.net.mx
Puebla, Pue. (Matriz):
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: datos@puebla.megared.net.mx
Chihuahua
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: Cefeo@soluglobales.com
Distrito Federal:
QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : gacosta@qplus.com.mx
Guerrero Acapulco
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
MERIDA:
ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: rrrb@sureste.com
Tijuana:
STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico
4.3: ViewSonic Mexico Limited Warranty
90
Villahermosa:
Compumantenimietnos Garantizados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: compumantenimientos@prodigy.net.mx
Veracruz, Ver.:
CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01-22-91-00-31-67
E-Mail: gacosta@qplus.com.mx
Cuernavaca
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: aquevedo@compusupportcva.com
Guadalajara, Jal.:
SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: mmiranda@servicrece.com
Monterrey:
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: aydeem@gps1.com.mx
Oaxaca, Oax.:
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Fax: 01(52)95-15-13-67-00
E-Mail. gpotai2001@hotmail.com
FOR USA SUPPORT:
ViewSonic Corporation
381 Brea Canyon Road, Walnut, CA. 91789 USA
Tel: 800-688-6688 (English); 866-323-8056 (Spanish);
Fax: 1-800-685-7276
E-Mail: http://www.viewsonic.com
PRJ_LW03 Rev. 1A 06-25-07
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising