Biostar G41U3G motherboard User's manual

G41U3G Setup Manual

FCC Information and Copyright

This equipment has been tested and found to comply with the limits of a Class

B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand.

Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendor’s approval in writing.

The content of this user’s manual is subject to be changed without notice and we will not be responsible for any mistakes found in this user’s manual. All the brand and product names are trademarks of their respective companies.

Dichiarazione di conformità sintetica

Ai sensi dell’art. 2 comma 3 del D.M.

275 del 30/10/2002

Si dichiara che questo prodotto è conforme alle normative vigenti e soddisfa i requisiti essenziali richiesti dalle direttive

Short Declaration of conformity

We declare this product is complying with the laws in force and meeting all the essential requirements as specified by the directives

2004/108/CE, 2006/95/CE and

1999/05/CE whenever these laws may be applied

2004/108/CE, 2006/95/CE e

1999/05/CE quando ad esso applicabili

Table of Contents

Chapter 1: Introduction ............................................................ 1

1.1 Before You Start ................................................................................ 1

1.2

1.3

Package Checklist ............................................................................. 1

Motherboard Features...................................................................... 2

1.4

1.5

Rear Panel Connectors ..................................................................... 3

Motherboard Layout......................................................................... 4

Chapter 2: Hardware Installation ............................................. 5

2.1

2.2

Installing Central Processing Unit (CPU)....................................... 5

FAN Headers...................................................................................... 7

2.3 Installing System Memory................................................................ 8

2.4 Connectors and Slots ....................................................................... 10

Chapter 3: Headers & Jumpers Setup ..................................... 13

3.1 How to Setup Jumpers .................................................................... 13

3.2 Detail Settings.................................................................................. 13

Chapter 4: Useful Help ............................................................ 18

4.1 Driver Installation Note.................................................................. 18

4.2

4.3

4.4

4.5

Software............................................................................................ 19

Extra Information............................................................................ 23

AMI BIOS Beep Code....................................................................... 25

Troubleshooting............................................................................... 26

Appendix: SPEC In Other Languages ...................................... 28

German.................................................................................................................. 28

French .................................................................................................................... 30

Italian..................................................................................................................... 32

Spanish ................................................................................................................... 34

Portuguese ............................................................................................................ 36

Polish...................................................................................................................... 38

Russian ................................................................................................................... 40

Arabic..................................................................................................................... 42

Japanese ................................................................................................................ 44

G41U3G

CHAPTER 1: INTRODUCTION

1.1 B

EFORE

Y

OU

S

TART

Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below:

Prepare a dry and stable working environment with sufficient lighting.

Always disconnect the computer from power outlet before operation.

Before you take the motherboard out from anti-static bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge.

Avoid touching the components on motherboard or the rear side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board.

Do not leave any unfastened small parts inside the case after installation. Loose parts will cause short circuits which may damage the equipment.

Keep the computer from dangerous area, such as heat source, humid air and water.

1.2 P

ACKAGE

C

HECKLIST

HDD Cable X 1 (optional)

Serial ATA Cable X 2

Rear I/O Panel for ATX Case X 1

Installation Guide X 1

Fully Setup Driver CD X 1 (full version manual files inside)

FDD Cable X 1 (optional)

USB 2.0 Cable X1 (optional)

Serial ATA Power Cable X 1 (optional)

Note: The package contents may be different due to area or your motherboard version.

1

Motherboard Manual

1.3 M

OTHERBOARD

F

EATURES

CPU

SPEC

LGA 775

Intel Core2Duo / Core2Quad /

Pentium Dual-Core / Celeron Dual-Core /

Enhanced Intel SpeedStep® / Intel Architecture-64 /

Extended Memory 64 Technology / Virtualization

Celeron 4xx processor

Supports Hyper-Threading / Execute Disable Bit /

Technology

(Maximum Watt: 95W)

Support 800 / 1066 / 1333 MHz FSB

Chipset

Super I/O

Main

Memory

Graphics

IDE

SATA 2

Intel G41

Intel ICH7

ITE 8721 Environment Control initiatives,

Provides the most commonly used legacy Hardware Monitor Controller

Super I/O functionality.

Low Pin Count Interface

Fan Speed Controller

ITE's "Smart Guardian" function

DIMM Slots x 2

Each DIMM supports 256MB / 512MB /

1GB / 2GB / 4GB DDR3

Max Memory Capacity 8GB

Dual Channel Mode DDR3 memory module

Supports DDR3 800/1066/1333(OC)

Registered DIMM and ECC DIMM is not supported

(CPU with FSB 800 MHz only supports DDR3 800)

GMA X4500

Integrated IDE Controller

Integrated Serial ATA Controller

Max Shared Video Memory is 1984MB

(Depending on OS and memory size)

Ultra DMA 33 / 66 / 100 Bus Master Mode supports PIO Mode 0~4

Data transfer rates up to 3.0 Gb/s.

SATA Version 2.0 specification compliant

LAN Realtek RTL 8111DL 10 / 100 Mb/s / 1Gb/s auto negotiation

Sound

Codec

ALC662

USB3.0 Asmedia ASM1042

Slots

PCI slot

PCI Express x 16 slot

On Board Floppy Connector

Connectors

Printer Port Connector

Serial Port Connector

IDE Connector

5.1 channels audio out

High Definition Audio

Data transfer rates is limited to 250 MB/s due to spec of

PCIE1.0 x1 x2 Supports PCI expansion cards x1 Supports PCI-E x16 expansion cards x1 Each connector supports 2 Floppy drives x1 Each connector supports 1 Printer port x1 Connects to RS-232 Port x1 Each connector supports 2 IDE device

2

SATA Connector

Front Panel Connector

Front Audio Connector

CPU Fan Header

System Fan Header

Clear CMOS Header

USB 2.0 Connector

Power Connector (24pin)

Power Connector (4pin)

PS/2 Keyboard

PS/2 Mouse

VGA port

Back Panel LAN port

I/O

USB 2.0 Port

USB 3.0 Port

Audio Jack

G41U3G

SPEC x4 Each connector supports 1 SATA device x1 Supports front panel facilities x1 Supports front panel audio function x1 CPU Fan power supply (with Smart Fan function) x1 System Fan Power supply x1 Restore CMOS data to factory default x2 Each connector supports 2 front panel USB 2.0 ports x1 Connects to Power supply x1 x2 x2 x1 Connects to Power supply x1 Connects to PS/2 Keyboard x1 x1

Connects to PS/2 Mouse

Connect to D-SUB monitor x3

Connect to RJ-45 ethernet cable

Connect to USB 2.0 devices

Connect to USB3.0 devices (by Asmedia ASM1042) and USB2.0/USB1.X devices (by Intel ICH7)

Provide Audio-In/Out and microphone connection

Board Size 192 (W) x 235 (L) mm

Biostar reserves the right to add or remove support for

OS Support Windows 2000 / XP / Vista / 7 any OS with or without notice

1.4 R

EAR

P

ANEL

C

ONNECTORS

P S/2

M ouse

LA N

Line In/

S urround

US B 3.0X 2

Line Out

Mic In 1/

Bas s/ Center

PS /2 V GA US B 2.0X 2

K eyboard

NOTE: Since the audio chip supports High Definition Audio Specification, the function of each audio jack can be defined by software. The input / output function of each audio jack listed above represents the default setting. However, when connecting external microphone to the audio port, please use the Line In (blue) and Mic In (Pink) audio jack.

NOTE: USB3.0 ports are backward compatible with USB2.0/USB1.X devices. USB3.0 is controlled by Asmedia ASM1042, but, USB2.0/USB1.X is controlled by Intel ICH7.

3


1.5 M

OTHERBOARD

L

AYOUT

KBMS1

LGA775

CPU1

ATXPWR2

ATXPWR1

CPU_FAN1

USB3_0

JUSBV1

JUSBV2

Intel

G41

RJ45USB1

4

BIOS

AUD IO1

F_AUDIO1

PEX16_1

LAN

PCI1

Super

I/O

J_PRIN T1

PCI2

J_COM1

SYS_FAN1

F_USB2

JUSBV3

Codec

FDD1

Note: ■ represents the 1 st pin.

PANEL1

JCMOS1 SATA1

Intel

ICH7

SATA2

BAT1

SATA4

SATA3

CHAPTER 2: HARDWARE INSTALLATION

2.1 I

NSTALLING

C

ENTRAL

P

ROCESSING

U

NIT

(CPU)

G41U3G

Special Notice:

Remove Pin Cap before installation, and make good preservation for future use. When the CPU is removed, cover the Pin Cap on the

empty socket to ensure pin legs won’t be damaged.

Pin-Cap

Step 1: Pull the socket locking lever out from the socket and then raise the lever up to a 90-degree angle.

5


Step 2: Look for the triangular cut edge on socket, and the golden dot on

CPU should point forwards this triangular cut edge. The CPU will fit only in the correct orientation.

Step 2-2:

Step 3: Hold the CPU down firmly, and then lower the lever to locked position to complete the installation.

Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it on the retention frame. Connect the CPU FAN power cable into the CPU_FAN1. This completes the installation.

6

G41U3G

2.2 FAN H

EADERS

These fan headers support cooling-fans built in the computer. The fan cable and connector may be different due to the fan manufacturer.

Connect the fan cable to the connector while matching the black wire to pin#1.

CPU_FAN1: CPU Fan Header

1 4

Pin Assignment

1 Ground

2 Power

3 FAN RPM rate sense

4 Smart Fan Control

SYS_FAN1: System Fan Header

Pin Assignment

1 Ground

2 +12V

3 FAN RPM rate sense

3

1

Note:

CPU_FAN1 supports 4-pin head connector; SYS_FAN1, 3-pin head one. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin#2, and the black wire is Ground and should be connected to

GND.

7


2.3 I

NSTALLING

S

YSTEM

M

EMORY

A. DDR3 module

1. Unlock a DIMM slot by pressing the retaining clips outward. Align a

DIMM on the slot such that the notch on the DIMM matches the break on the Slot.

8

2. Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.

G41U3G

B. Memory Capacity

DIMM Socket

Location

DDR3 Module

Total Memory

Size

DDR3_B1 256MB/512MB/1GB/2GB/4GB

C. Dual Channel Memory Installation

Please refer to the following requirements to activate Dual Channel function:

Install memory module of the same density in pairs, shown in the table.

Dual Channel Status DDR3_A1 DDR3_B1

(O means memory installed; X, not installed.)

The DRAM bus width of the memory module must be the same(x8 or x16)

9


2.4 C

ONNECTORS AND

S

LOTS

FDD1: Floppy Disk Connector

The motherboard provides a standard floppy disk connector that supports 360K,

720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the provided floppy drive ribbon cables.

2

1

3 4

3 3

IDE1: Hard Disk Connector

The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO

Mode 0~4, Bus Master, and Ultra DMA 33/66/100 functionality.

The IDE connector can connect a master and a slave drive, so you can connect up to two hard disk drives.

40 39

2 1

10

G41U3G

ATXPWR1: ATX Power Source Connector

This connector allows user to connect 24-pin power connector on the ATX power supply.

12 24

Pin Assignment

13 +3.3V

14 -12V

15 Ground

16 PS_ON

17 Ground

18 Ground

19 Ground

20 NC

21 +5V

22 +5V

23 +5V

24 Ground

1 13

Pin Assignment

1 +3.3V

2 +3.3V

3 Ground

4 +5V

5 Ground

6 +5V

7 Ground

8 PW_OK

10 +12V

11 +12V

12 +3.3V

ATXPWR2: ATX Power Source Connector

This connector provides +12V to CPU power circuit.

2

3

1

4

Pin Assignment

1 +12V

2 +12V

3 Ground

4 Ground

Note:

Before you power on the system, please make sure that both ATXPWR1 and ATXPWR2 connectors have been plugged-in.

11


PEX16_1: PCI-Express x16 Slot

- PCI-Express 1.0a compliant.

-

-

-

Maximum theoretical realized bandwidth of 4GB/s simultaneously per direction, for an aggregate of 8GB/s totally.

PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.

2X bandwidth over the traditional PCI architecture.

PEX16_1

PCI1/PCI2: Peripheral Component Interconnect Slots

This motherboard is equipped with 2 standard PCI slots. PCI stands for

Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits.

PCI1

PCI2

12

G41U3G

CHAPTER 3: HEADERS & JUMPERS SETUP

3.1 H

OW TO

S

ETUP

J

UMPERS

The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is “close”, if not, that means the jumper is

“open”.

3.2 D

ETAIL

S

ETTINGS

PANEL1: Front Panel Header

This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and speaker connection. It allows user to connect the PC case’s front panel switch functions.

9

1

PWR_LED

On/Off

+ +

-

+

-

16

8

SPK

RST

HLED

Pin Assignment Function Function

1 +5V

2 N/A

3 N/A

4 Speaker

5

6

HDD LED (+)

HDD LED (-)

7 Ground

Speaker

Connector

Hard drive

LED

9 N/A

10 N/A

11 N/A

12 Power LED (+)

13

14

Power LED (+)

Power LED (-)

N/A

N/A

Power LED

Reset button Power-on button

16 Ground

13


F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel

This motherboard provides 2 USB 2.0 headers, which allows user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader.

Pin Assignment

F_USB1

F_USB2

2 1 0

1 9

3 USB-

4 USB-

5 USB+

6 USB+

7 Ground

8 Ground

9 Key

10 NC

JUSBV1/JUSBV2/JUSBV3: Power Source Headers for USB Ports

Pin 1-2 Close:

JUSBV1: +5V for USB ports at USB3_0.

JUSBV2: +5V for USB ports at RJ45USB1.

JUSBV3: +5V for USB ports at F_USB1/F_USB2.

Pin 2-3 Close:

JUSBV1: +5V STB for USB ports at USB3_0.

JUSBV2: +5V STB for USB ports at RJ45USB1.

JUSBV3: +5V STB for USB ports at F_USB1/F_USB2.

JUSBV1

JUSBV2

1 3

JUSBV3

1 3

Pin 1-2 close

1 3

Pin 2-3 close

14

G41U3G

JCMOS1: Clear CMOS Header

Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and the CMOS data. Please carefully follow the procedures to avoid damaging the motherboard.

1

3

Pin 1-2 Close:

Normal Operation

(Default).

1

1

3

Pin 2-3 Close:

Clear CMOS data. 3

※

Clear CMOS Procedures:

1.

2.

3.

4.

5.

Remove AC power line.

Set the jumper to “Pin 2-3 close”.

Wait for five seconds.

Set the jumper to “Pin 1-2 close”.

Power on the AC.

6. Reset your desired password or clear the CMOS data.

SATA1~SATA4: Serial ATA Connectors

The motherboard has a PCI to SATA Controller with 4channels SATA interface, it satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s.

Pin Assignment

1 Ground

2 TX+

3 TX-

4 Ground

5 RX-

6 RX+

7 Ground

SATA1 SATA2

SATA4

SATA3

1 4 7

15


F_AUDIO1: Front Panel Audio Header

This header allows user to connect the front audio output cable with the PC front panel. This header allows only HD audio front panel connector; AC’97 connector is not acceptable.

10 9

Pin Assignment

1 Mic Left in

2 Ground

3 Mic Right in

4 GPIO

5 Right line in

2 1

8 Key

9 Left line in

J_COM1: Serial port Connector

The motherboard has a Serial Port Connector for connecting RS-232 Port.

Pin Assignment

2

1

4 Data terminal ready

10

9

7

8

Request to send

Clear to send

10 Key

16

J_PRINT1: Printer Port Connector

This header allows you to connector printer on the PC.

G41U3G

2 26

1 25

Pin Assignment Pin Assignment

1 -Strobe 14 Ground

2 -ALF

16 Ground

4 -Error

6 -Init

8 -Scltin

18 Ground

19 -ACK

20 Ground

21 Busy

10 Ground

12 Ground

22 Ground

23 PE

24 Ground

25 SCLT

26 Key

17


CHAPTER 4: USEFUL HELP

4.1 D

RIVER

I

NSTALLATION

N

OTE

After you installed your operating system, please insert the Fully Setup

Driver CD into your optical drive and install the driver for better system performance.

You will see the following window after you insert the CD

18

The setup guide will auto detect your motherboard and operating system.

Note:

If this window didn’t show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation

To install the driver, please click on the Driver icon. The setup guide will list the compatible driver for your motherboard and operating system.

Click on each device driver to launch the installation program.

B. Software Installation

To install the software, please click on the Software icon. The setup guide will list the software available for your system, click on each software title to launch the installation program.

C. Manual

Aside from the paperback manual, we also provide manual in the Driver

CD. Click on the Manual icon to browse for available manual.

Note:

You will need Acrobat Reader to open the manual file. Please download the latest version of Acrobat Reader software from

http://www.adobe.com/products/acrobat/readstep2.html

G41U3G

4.2 S

OFTWARE

Installing Software

1. Insert the Setup CD to the optical drive. The drivers installation program would appear if the Autorun function has been enabled. title.

3. Follow the on-screen instructions to complete the installation.

Launching Software

After the installation process, you will see the software icon “eHOT Line” /

“BIOS Update” appears on the desktop. Double-click the icon to launch the utility.

eHot-Line (Optional)

eHot-Line is a convenient utility that helps you to contact with our

Tech-Support system. This utility will collect the system information which is useful for analyzing the problem you may have encountered, and then send these information to our tech-support department to help you fix the problem.

Before you use this utility, please set Outlook Express as your default e-mail client application program. informa ti on that you must provide. Wi thout this information, you may not be able to send out the mail.

This bl ock will show the i nformation which would be collected in the mail .

* Describe conditi on of your system.

* Select your area or the area cl ose to you.

Provide the e-ma il address that you would like to send the copy to.

* Provid e the name of the memory module manufacturer.

Send the mail out.

Exi t thi s dialog.

Save these in forma tion to a .txt file

Provide the name of the power suppl y manufacturer and the model no.

19


After filling up this information, click “Send” to send the mail out. A warning dialog would appear asking for your confirmation; click

“Send” to confirm or “Do Not Send” to cancel.

If you want to save this information to a .txt file, click “Save As…” and then you will see a saving dialog appears asking you to enter file name.

Enter the file name and then click

“Save”. Your system information will be saved to a .txt file.

Open the saved .txt file, you will see your system information including motherboard/BIOS/CPU/video/ device/OS information. This information is also concluded in the sent mail.

We will not share customer’s data with any other third parties, so please feel free to provide your system information while using eHot-Line service.

If you are not using Outlook Express as your default e-mail client application, you may need to save the system information to a .txt file and send the file to our tech support with other e-mail application.

Go to the following web http://www.biostar.com.tw/app/en-us/about/contact.php

for getting our contact information.

20

G41U3G

BIOS Update

BIOS Update is a convenient utility which allows you to update your motherboard BIOS under Windows system.

AWARD BIOS

Show current BIOS information

AMI BIOS

Clear CMOS function

(Only for AWARD BIOS)

Save current BIOS to a .bin file

Update BIOS with a BIOS file

<Backup BIOS>

Once click on this button, the saving dialog will show. Choose the position to save file and enter file name. (We recommend that the file name should be English/number and no longer than 7 characters.)

Then click Save.

21


<Update BIOS>

Before doing this, please download the proper BIOS file from the website.

For AWARD BIOS, update BIOS procedure should be run with Clear CMOS function, so please check on Clear CMOS first.

Then click Update BIOS button, a dialog will show for asking you backup current BIOS. Click Yes for BIOS backup and refer to the Backup BIOS procedure; or click No to skip this procedure.

After the BIOS Backup procedure, the open dialog will show for requesting the

BIOS file which is going to be updated.

Please choose the proper BIOS file for updating, then click on Open.

The utility will update BIOS with the proper BIOS file, and this process may take minutes. Please do not open any other applications during this process.

After the BIOS Update process, click on

OK to restart the system.

While the system boots up and the full screen logo shows, press key to enter BIOS setup.

<Delete>

In the BIOS setup, use the Load Optimized Defaults function and then Save and

Exit Setup to exit BIOS setup. BIOS Update is completed.

All the information and content above about the software are subject to be changed without notice. For better performance, the software is being continuously updated.

The information and pictures described above are for your reference only. The actual information and settings on board may be slightly different from this manual.

22

G41U3G

4.3 E

XTRA

I

NFORMATION

CPU Overheated

If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated.

When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again.

In this case, please double check:

1. The CPU cooler surface is placed evenly with the CPU surface.

2. CPU fan is rotated normally.

3. CPU fan speed is fulfilling with the CPU speed.

After confirmed, please follow steps below to relief the CPU protection function.

1. Remove the power cord from power supply for seconds.

2. Wait for seconds.

3. Plug in the power cord and boot up the system.

Or you can:

1. Clear the CMOS data.

(See “Close CMOS Header: JCMOS1” section)

2. Wait for seconds.

3. Power on the system again.

23


BIO-Flasher

BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to update your BIOS via USB pen drive or floppy disk.

The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>

during the Power-On Self Tests (POST) procedure while booting up.

Updating BIOS with BIO-Flasher

1. Go to the website to download the latest BIOS file for the motherboard.

2. Then, save the BIOS file into a USB pen drive or a floppy disk.

3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the

USB port or the floppy disk drive.

4. Power on or reset the computer and then press <F12> during the POST process.

A select dialog as the picture on the right appears.

Select the device contains the BIOS file and press <Enter> to enter the utility.

5. The utility will show the BIOS files and their respective information. Select the proper

BIOS file and press <Enter> then <Y> to perform the BIOS update process.

6. After the update process, the utility will ask you to reboot the system.

Press <Y> to proceed. BIOS update completes. z This utility only allows storage device with FAT32/16 format and single partition. z Shutting down or resetting the system while updating the BIOS will lead to system boot failure.

24

G41U3G

4.4 AMI BIOS B

EEP

C

ODE

Boot Block Beep Codes

Number of Beeps

1

2

3

4

5

7

10

11

12

13

Description

No media present. (Insert diskette in floppy drive A:)

“AMIBOOT.ROM” file not found in root directory of diskette in

A:

Insert next diskette if multiple diskettes are used for recovery

Flash Programming successful

File read error

No Flash EPROM detected

Flash Erase error

Flash Program error

“AMIBOOT.ROM” file size error

BIOS ROM image mismatch (file layout does not match image present in flash device)

POST BIOS Beep Codes

Number of Beeps

1

3

6

7

8

Description

Memory refresh timer error

Base memory read/write test error

Keyboard controller BAT command failed

General exception error (processor exception interrupt error)

Display memory error (system video adapter)

Troubleshooting POST BIOS Beep Codes

Number of Beeps Troubleshooting Action

1, 3

6, 7

8

Reseat the memory, or replace with known good modules.

Fatal error indicating a serious problem with the system.

Consult your system manufacturer. Before declaring the motherboard beyond all hope, eliminate the possibility of interference by a malfunctioning add-in card. Remove all expansion cards except the video adapter. z If beep codes are generated when all other expansion cards are absent, consult your system manufacturer’s technical support. z If beep codes are not generated when all other expansion cards are absent, one of the add-in cards is causing the malfunction. Insert the cards back into the system one at a time until the problem happens again. This will reveal the malfunctioning card.

If the system video adapter is an add-in card, replace or reseat the video adapter. If the video adapter is an integrated part of the system board, the board may be faulty.

25


4.5 T

ROUBLESHOOTING

Probable Solution

1. There is no power in the system.

Power LED does not shine; the fan of the power supply does not work

2. Indicator light on keyboard does not shine.

1. Make sure power cable is securely plugged in.

3. Contact technical support.

System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running.

System does not boot from a hard disk drive, but can be booted from optical drive.

System only boots from an optical drive. Hard disks can be read, applications can be used, but system fails to boot from a hard disk.

Using even pressure on both ends of the DIMM, press down firmly until the module snaps into place.

1. Check cable running from disk to disk controller board. Make sure both ends are securely plugged in; check the drive type in the standard CMOS setup.

2. Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time.

1. Back up data and applications files.

2. Reformat the hard drive.

Re-install applications and data using backup disks.

Screen message shows “Invalid

Configuration” or “CMOS Failure.”

Review system’s equipment. Make sure correct information is in setup.

System cannot boot after user installs a second hard drive.

1. Set master/slave jumpers correctly.

2. Run SETUP program and select correct drive types. Call the drive manufacturers for compatibility with other drives.

26

This page is intentionally left blank.

G41U3G

27


APPENDIX: SPEC IN OTHER LANGUAGES

G

ERMAN

CPU

Spezifikationen

LGA 775



Celeron 4xx Prozessoren

(Maximales Watt: 95W)

Unterstützt Hyper-Threading / Execute Disable Bit /



Technology

FSB

Chipsatz

Intel G41

Intel ICH7

Super E/A

ITE 8721 Umgebungskontrolle,

Bietet die häufig verwendeten alten Super Hardware-Überwachung

E/A-Funktionen.

Low Pin Count-Schnittstelle

Lüfterdrehzahl-Controller/-Überwachung

"Smart Guardian"-Funktion von ITE er

DDR3 DIMM-Steckplätze x 2

1GB / 2GB / 4GB DDR3.

Dual-Kanal DDR3 Speichermodul

Arbeitsspeich Jeder DIMM unterstützt 256MB / 512MB /

Unterstützt DDR3 800/1066/1333(OC) registrierte DIMMs. ECC DIMMs werden nicht unterstützt.

Max. 8GB Arbeitsspeicher

(CPU mit 800 MHz FSB unterstützt nur DDR3-800)

Grafik

IDE

SATA

800 / 1066 / 1333 MHz

GMA X4500

Integrierter IDE-Controller

Integrierter Serial ATA-Controller

Max. 1984MB gemeinsam benutzter Videospeicher

(Abhängig von OS und Speichergröße)

Ultra DMA 33 / 66 / 100 Bus Master-Modus

Unterstützt PIO-Modus 0~4,

Datentransferrate bis zu 3.0Gb/s

Konform mit der SATA-Spezifikation Version 2.0.

LAN Realtek RTL 8111DL 10 / 100 / 1000 Mb/s Auto-Negotiation

HD

Audio-Unters ALC662

Unterstützt High-Definition Audio

5.1-Kanal-Audioausgabe tützung

USB3.0

Steckplätze

Asmedia ASM1042

Datenübertragungsraten bis 250 beschränkt MB / s durch Spezifikation des PCIE1.0 x1

PCI-Steckplatz x2

PCI Express x16 Steckplatz x1

28

G41U3G

Diskettenlaufwerkanschluss

Druckeranschluss Anschluss

Serieller Anschluss

IDE-Anschluss

Spezifikationen x1 x1 x1 x1

Jeder Anschluss unterstützt 2 Diskettenlaufwerke

Jeder Anschluss unterstützt 1 Druckeranschluss

Jeder Anschluss unterstützt 2 IDE-Laufwerke

SATA-Anschluss

Fronttafelanschluss x4 x1

Jeder Anschluss unterstützt 1 SATA-Laufwerk

Unterstützt die Fronttafelfunktionen

Onboard-Ans

Front-Audioanschluss chluss x1 Unterstützt die Fronttafel-Audioanschlussfunktion

CPU-Lüfterstromversorgungsanschluss (mit Smart

CPU-Lüfter-Sockel x1

Fan-Funktion)

"CMOS löschen"-Sockel x1

Jeder Anschluss unterstützt 2 Fronttafel-USB

USB 2.0-Anschluss x2

2.0-Anschlüsse

Stromanschluss (24-polig)

Stromanschluss (4-polig) x1 x1

PS/2-Tastatur

PS/2-Maus x1 x1

VGA-Anschluss x1

Rückseiten-E LAN-Anschluss x1

/A USB 2.0-Anschluss x2

USB 3.0-Anschluss x2 USB3.0 Geräte (durch Asmedia ASM1042)

USB2.0/USB1.X Geräte (durch Intel ICH7)

Audioanschluss x3

Platinengröße 192 mm (B) X 235 mm (L)

OS-Unterstüt zung

Windows 2000 / XP / Vista / 7

Biostar behält sich das Recht vor, ohne Ankündigung die Unterstützung für ein Betriebssystem hinzuzufügen oder zu entfernen.

29


F

RENCH

UC

SPEC

LGA 775

Processeurs Intel Core2Duo / Core2Quad

/ Pentium Dual-Core / Celeron Dual-Core / d'exécution de bit de désactivation / Intel SpeedStep® optimisée/ d'architecture Intel 64 / de mémoire

Celeron 4xx

Prend en charge les technologies Hyper-Threading /

étendue 64 / de virtualisation

(Watt maximum : 95W)

Bus frontal 800 / 1066 / 1333 MHz

Intel G41

Chipset

Intel ICH7

Super E/S

ITE 8721

Fournit la fonctionnalité de Super E/S patrimoniales la plus utilisée.

Interface à faible compte de broches

Initiatives de contrôle environnementales,

Moniteur de matériel

Contrôleur /moniteur de vitesse de ventilateur

Fonction "Gardien intelligent" de l'ITE

Mémoire principale

SATA

Fentes DDR3 DIMM x 2

Module de mémoire DDR3 à mode à double voie

Prend en charge la DDR3 800/1066/1333(OC)

Chaque DIMM prend en charge des DDR3 Les DIMM à registres et DIMM avec code correcteurs de 256Mo / 512Mo / 1Go / 2Go / 4Go

Capacité mémoire maximale de 8Go d'erreurs ne sont pas prises en charge

(UC avec FSB 800 MHz ne prend en charge que DDR3

800)

Graphiques GMA X4500

IDE Contrôleur IDE intégré

Contrôleur Serial ATA intégré

Mémoire vidéo partagée maximale de 1984 Mo

(Selon la capacité d'OS et de mémoire)

Mode principale de Bus Ultra DMA 33 / 66 / 100

Prend en charge le mode PIO 0~4,

Taux de transfert jusqu'à 3.0Go/s.

Conforme à la spécification SATA Version 2.0

LAN

Prise en charge audio HD

Realtek RTL 8111DL

ALC662

10 / 100 / 1000 Mb/s négociation automatique

Prise en charge de l'audio haute définition

Sortie audio à 5.1 voies

USB3.0

Fentes

Asmedia ASM1042

Fente PCI

Fente PCI Express x16 x2 x1

Taux de transfert de données est limité à 250 Mo / s en raison de spécifications de PCIE1.0 x1

30

Connecteur de disquette

G41U3G x1

SPEC

Chaque connector prend en charge 2 lecteurs de disquettes

Connecteur de Port d'imprimante x1 Chaque connector prend en charge 1 Port d'imprimante

Port série x1

Connecteur IDE x1

Chaque connecteur prend en charge 2 périphériques

IDE

Connecteur SATA

Embase de ventilateur système

Embase d'effacement CMOS

Connecteur USB 2.0 x4

Connecteur du panneau avant x1 Prend en charge les équipements du panneau avant

Connecteur Connecteur Audio du panneau avant x1 Prend en charge la fonction audio du panneau avant embarqué

Alimentation électrique du ventilateur UC (avec fonction

Embase de ventilateur UC x1 de ventilateur intelligent) x1 x1 x2

Chaque connecteur prend en charge 1 périphérique

SATA

Alimentation électrique du ventilateur système

Chaque connecteur prend en charge 2 ports USB 2.0 de panneau avant x1 Connecteur d'alimentation

(24 broches)

Connecteur d'alimentation

(4 broches)

E/S du panneau arrière

Clavier PS/2

Souris PS/2

Port VGA

Port LAN

Port USB 2.0

Port USB 3.0

Fiche audio

Dimensions

192 mm (l) X 235 mm (H) de la carte x1 x1 x1 x1 x1 x2 x2 x3

USB3.0 dispositifs (par Asmedia ASM1042)

USB2.0/USB1.X dispositifs (par Intel ICH7)

Support SE Windows 2000 / XP / Vista / 7

Biostar se réserve le droit d'ajouter ou de supprimer le support de SE avec ou sans préavis.

31


I

TALIAN

SPECIFICA

CPU

LGA 775

Processore Intel Core2Duo /

Core2Quad / Pentium Dual-Core /

Celeron Dual-Core / Celeron 4xx

(Watt massimo: 95W)

800 / 1066 / 1333 MHz

Supporto di Hyper-Threading / Execute Disable

Bit / Enhanced Intel SpeedStep® / Architettura

Intel 64 / Tecnologia Extended Memory 64 /

Tecnologia Virtualization

FSB

Chipset

Intel G41

Intel ICH7

ITE 8721 Funzioni di controllo dell’ambiente:

Super I/O

Fornisce le funzionalità legacy Super

I/O usate più comunemente.

Monitoraggio hardware

Controller / Monitoraggio velocità ventolina

Interfaccia LPC (Low Pin Count) Funzione "Smart Guardian" di ITE

Memoria

Alloggi DIMM DDR3 x 2 Modulo di memoria DDR3 a canale doppio

Ciascun DIMM supporta DDR3 256MB Supporto di DDR3 800/1066/1333(OC) principale / 512MB / 1GB / 2GB / 4GB DIMM registrati e DIMM ECC non sono supportati

Capacità massima della memoria 8GB (CPU con FSB a 800 MHz supporta solo DDR3 800)

SATA Controller Serial ATA integrato

La memoria video condivisa massima è di 1984MB

(Secondo l'OS e la capacità di memoria)

Modalità Bus Master Ultra DMA 33 / 66 / 100

Supporto modalità PIO Mode 0-4

Velocità di trasferimento dei dati fino a 3.0Gb/s.

Compatibile specifiche SATA Versione 2.0.

LAN Realtek RTL 8111DL

Supporto audio HD

ALC662

USB3.0

Alloggi

Asmedia ASM1042

Alloggio PCI

Alloggio PCI Express x16 x2 x1

Negoziazione automatica 10 / 100 / 1000 Mb/s

Supporto audio High-Definition (HD)

Uscita audio 5.1 canali velocità di trasferimento dati è limitata a 250 MB / s, a causa delle specifiche di PCIE1.0 x1

32

G41U3G

Connettore floppy

SPECIFICA x1 Ciascun connettore supporta 2 unità Floppy

Connettore Porta stampante x1 Ciascun connettore supporta 1 Porta stampante

Porta seriale

Connettore IDE x1 x1 Ciascun connettore supporta 2 unità IDE

Connettori su scheda

Connettore SATA x4 Ciascun connettore supporta 1 unità SATA

Connettore pannello frontale x1 Supporta i servizi del pannello frontale

Connettore audio frontale

Collettore ventolina CPU

Collettore ventolina sistema x1 Supporta la funzione audio pannello frontale

Alimentazione ventolina CPU (con funzione Smart x1

Fan) x1 Alimentazione ventolina di sistema

Collettore cancellazione CMOS x1

Ciascun connettore supporta 2 porte USB 2.0

Connettore USB 2.0 x2 pannello frontale

Connettore alimentazione x1

(24 pin)

Connettore alimentazione x1

(4 pin)

Tastiera PS/2

Mouse PS/2

Porta VGA

I/O

Porta LAN pannello posteriore

Porta USB 2.0

Porta USB 3.0

Connettore audio

Dimension 192 mm (larghezza) x 235 mm i scheda

Sistemi

(altezza) operativi supportati

Windows 2000 / XP / Vista / 7 x3 x1 x1 x1 x1 x2 x2 USB3.0 dispositivi (da Asmedia ASM1042)

USB2.0/USB1.X dispositivi (da Intel ICH7)

Biostar si riserva il diritto di aggiungere o rimuovere il supporto di qualsiasi sistema operativo senza preavviso.

33


S

PANISH

CPU

FSB

Especificación

LGA 775

Procesador Intel Core2Duo / Core2Quad /

Admite Hyper-Threading / Bit de deshabilitación de ejecución / Intel SpeedStep® Mejorado / Intel


Architecture-64 / Tecnología Extended Memory 64 /

Celeron 4xx

Tecnología de virtualización

(Vatio máximo: 95W)

800 / 1066 / 1333 MHz

Conjunto de Intel G41 chips Intel ICH7

ITE 8721 Iniciativas de control de entorno,

Súper E/S

Le ofrece las funcionalidades heredadas de Monitor hardware uso más común Súper E/S. Controlador/monitor de velocidad de ventilador

Interfaz de cuenta Low Pin Función "Guardia inteligente" de ITE

Memoria principal

IDE

SATA

Ranuras DIMM DDR3 x 2

Cada DIMM admite DDR de 256MB /

Módulo de memoria DDR3 de canal Doble

Admite DDR3 de 800/1066/1333(OC)

512MB / 1GB / 2GB / 4GB

Capacidad máxima de memoria de 8GB

No admite DIMM registrados o DIMM compatibles con

ECC (CPU con FSB de 800 MHz sólo soporta DDR3 800)

Controlador IDE integrado

Controlador ATA Serie Integrado

Memoria máxima de vídeo compartida de 1984MB

(Dependiendo de tamaño del OS y de la memoria)

Modo bus maestro Ultra DMA 33 / 66 / 100

Soporte los Modos PIO 0~4,

Tasas de transferencia de hasta 3.0 Gb/s.

Compatible con la versión SATA 2.0.

Red Local Realtek RTL 8111DL

Soporte de

ALC662 sonido HD

USB3.0

Ranuras

Asmedia ASM1042

Ranura PCI

Ranura PCI Express x16

X2

X1

Negociación de 10 / 100 / 1000 Mb/s

Soporte de sonido de Alta Definición

Salida de sonido de 5.1 canales

Tasas de transferencia de datos está limitada a 250 MB

/ s debido a una especificación de PCIE1.0 x1

34

G41U3G

Conector disco flexible

Conector Puerto de impresora

Puerto serie

Conector IDE

Especificación

X1

X1

Cada conector soporta 2 unidades de disco flexible

Cada conector soporta 1 Puerto de impresora

X1

Conector SATA

Conector de panel frontal

X1 Cada conector soporta 2 dispositivos IDE

X4 Cada conector soporta 1 dispositivos SATA

X1 Soporta instalaciones en el panel frontal

Conectores Cabecera de ventilador de CPU en placa

Conector de sonido frontal X1

X1

Soporta funciones de sonido en el panel frontal

Fuente de alimentación de ventilador de CPU (con función Smart Fan)

Cabecera de ventilador de sistema X1 Fuente de alimentación de ventilador de sistema

Cabecera de borrado de CMOS

Conector USB 2.0

Conector de alimentación

(24 patillas)

X1

X2

X1

Cada conector soporta 2 puertos USB 2.0 frontales

Conector de alimentación

(4 patillas)

X1

Teclado PS/2

Ratón PS/2

Panel trasero de

Puerto de red local

Puerto USB 2.0

E/S

Puerto VGA

Puerto USB 3.0

Conector de sonido

Tamaño de

192 mm. (A) X 235 Mm. (H) la placa

Soporte de sistema operativo


X1

X1

X1

X1

X2

X2 USB3.0 dispositivos (por Asmedia ASM1042)

USB2.0/USB1.X dispositivos (por Intel ICH7)

X3

Biostar se reserva el derecho de añadir o retirar el soporte de cualquier SO con o sin aviso previo.

35


P

ORTUGUESE

CPU

FSB

ESPECIFICAÇÕES

LGA 775

Processador Intel Core2Duo / Core2Quad Suporta as tecnologias Hyper-Threading / Execute

/ Pentium Dual-Core / Celeron Dual-Core / Disable Bit / Enhanced Intel SpeedStep® / Intel

Celeron 4xx Arquitecture -64 / Extended Memory 64 / Virtualization

(Watt máximo: 95W)

800 / 1066 / 1333 MHz

Chipset

Intel G41

Intel ICH7

ITE 8721

Especificaçã

Proporciona as funcionalidades mais o Super I/O utilizadas em termos da especificação

Super I/O.

Interface LPC (Low Pin Count).

Memória principal

Iniciativas para controlo do ambiente

Monitorização do hardware

Controlador/Monitor da velocidade da ventoinha

Função "Smart Guardian" da ITE

Ranhuras DIMM DDR3 x 2 Módulo de memória DDR3 de canal duplo

Cada módulo DIMM suporta uma Suporta módulos DDR3 800/1066/1333(OC) memória DDR3 de 256 MB / 512 MB / 1GB Os módulos DIMM registados e os DIMM ECC não são

/ 2GB / 4GB

Capacidade máxima de memória: 8GB suportados

(CPU com FSB 800 MHz só suporta DDR3 800)

Placa gráfica

GMA X4500

IDE

SATA

LAN

Suporte

Controlador IDE integrado

Controlador Serial ATA integrado

Realtek RTL 8111DL

Memória de vídeo máxima partilhada: 1984 MB

(Dependendo do tamanho do ósmio e de memória)

Modo Bus master Ultra DMA 33 / 66 / 100

Suporta o modo PIO 0~4,

Velocidades de transmissão de dados até 3.0 Gb/s.

Compatibilidade com a especificação SATA versão 2.0.

Auto negociação de 10 / 100 / 1000 Mb/s para áudio

ALC662 de alta definição

Suporta a especificação High-Definition Audio

Saída de áudio de 5.1 canais

USB3.0 Asmedia ASM1042

Taxas de transferência de dados é limitado a 250 MB / s, devido à especificação do PCIE1.0 x1 x2

Ranhuras

Ranhura PCI

36

G41U3G

ESPECIFICAÇÕES

Ranhura PCI Express x16 x1

Conector da unidade de disquetes x1 Cada conector suporta 2 unidades de disquetes

Conector da para impressora

Porta série x1 x1

Cada conector suporta 1 Porta para impressora

Conector IDE

Conector SATA

Conector do painel frontal x1 Para suporte de várias funções no painel frontal

Conector de áudio frontal x1 Suporta a função de áudio no painel frontal

Alimentação da ventoinha da CPU (com a função Smart

Conector da ventoinha da CPU x1

Fan)

Conectores

Conector da ventoinha do sistema x1 Alimentação da ventoinha do sistema na placa

Conector para limpeza do CMOS x1

Conector USB 2.0 x1 Cada conector suporta 2 dispositivos IDE x4 Cada conector suporta 1 dispositivo SATA x2

Cada conector suporta 2 portas USB 2.0 no painel frontal x1 Conector de alimentação

(24 pinos)

Conector de alimentação

(4 pinos)

Teclado PS/2

Entradas/S

Rato PS/2

Porta VGA aídas no painel

Porta LAN

Porta USB 2.0 traseiro Porta USB 3.0

Tomada de áudio x1 x1 x1 x1 x1 x2 x2 x3

USB3.0 dispositivos (por Asmedia ASM1042)

USB2.0/USB1.X dispositivos (por Intel ICH7)

Tamanho da placa

192 mm (L) X 235 mm (A)

Sistemas operativos Windows 2000 / XP / Vista / 7 suportados

A Biostar reserva-se o direito de adicionar ou remover suporte para qualquer sistema operativo com ou sem aviso prévio.

37


P

OLISH

Procesor

SPEC

LGA 775

Procesor Intel Core2Duo / Core2Quad /




Celeron 4xx

Obsługa Hyper-Threading / Execute Disable Bit /

Technology

(Maksymalny Watt: 95W)

FSB

Chipset

800 / 1066 / 1333 MHz

Intel G41

Intel ICH7

Pamięć główna

Gniazda DDR3 DIMM x 2

Każde gniazdo DIMM obsługuje moduły

256MB / 512MB / 1GB / 2GB / 4GB

Maks. wielkość pamięci 8GB

Moduł pamięci DDR3 z trybem podwójnego kanału

Obsługa DDR3 800/1066/1333(OC)

Brak obsługi Registered DIMM oraz ECC DIMM

(CPU z FSB 800 MHz tylko obsługuje pamięci DDR3 800)

Maks. wielkość współdzielonej pamięci video wynosi

1984MB (W zależności od wielkości pamięci i OS)

Super I/O

ITE 8721 Funkcje kontroli warunków pracy,

Zapewnia najbardziej powszechne funkcje Monitor H/W

Super I/O.

Interfejs Low Pin Count

Kontroler/Monitor prędkości wentylatora

Funkcja ITE "Smart Guardian"

SATA

LAN

Obsługa audio HD

USB3.0

Gniazda

Zintegrowany kontroler Serial ATA

Realtek RTL 8111DL

ALC662

Asmedia ASM1042

Gniazdo PCI

Gniazdo PCI Express x16

Ultra DMA 33 / 66 / 100 Tryb Bus Master obsługa PIO tryb 0~4,

Transfer danych do 3.0 Gb/s.

Zgodność ze specyfikacją SATA w wersji 2.0.

10 / 100 / 1000 Mb/s z automatyczną negocjacją szybkości

Obsługa High-Definition Audio

5.1 kanałowe wyjście audio x2 x1

Szybkość transmisji danych jest ograniczona do 250

MB / s ze względu na specyfikację PCIE1.0 x1

38

Złącze napędu dyskietek

Złącze Port drukarki

Port szeregowy

G41U3G

SPEC x1 Każde złącze obsługuje 2 napędy dyskietek x1 Każde złącze obsługuje 1 Port drukarki x1

Złącze IDE

Złącze SATA x1 Każde złącze obsługuje 2 urządzenia IDE x4 Każde złącze obsługuje 1 urządzenie SATA

Złącze panela przedniego x1 Obsługa elementów panela przedniego

Przednie złącze audio x1 Obsługa funkcji audio na panelu przednim

Złącza wbudowane

Złącze główkowe wentylatora

Zasilanie wentylatora procesora (z funkcją Smart Fan) procesora x1

Złącze główkowe wentylatora

Zasilanie wentylatora systemowego systemowego x1

Back Panel

I/O

Złącze główkowe kasowania CMOS x1

Każde złącze obsługuje 2 porty USB 2.0 na panelu

Złącze USB 2.0 x2 przednim

Złącze zasilania (24 pinowe)

Złącze zasilania (4 pinowe) x1 x1

Klawiatura PS/2

Mysz PS/2

Port VGA

Port LAN

Port USB 2.0

Port USB 3.0

Gniazdo audio x1 x1 x1 x1 x2 x2 x3

USB3.0 urządzeń (przez Asmedia ASM1042)

USB2.0/USB1.X urządzeń (przez Intel ICH7)

Wymiary płyty

192 mm (S) X 235 mm (W)

Obsluga systemu operacyjne

Windows 2000 / XP / Vista / 7 go

Biostar zastrzega sobie prawo dodawania lub odwoływania obsługi dowolnego systemu operacyjnego bez powiadomienia.

39


R

USSIAN

СПЕЦ

CPU

(центральн ый процессор)

LGA 775

Процессор Intel Core2Duo / Core2Quad /

Поддержка технологий Hyper-Threading / Execute

Disable Bit / Enhanced Intel SpeedStep® / Intel


Architecture-64 / Extended Memory 64 Technology /

Celeron 4xx технологии виртуализация

(Максимальный ватт: 95W)

FSB 800 / 1066 / 1333 МГц

Набор Intel G41 микросхем Intel ICH7

Основная память

Модуль памяти с двухканальным режимом DDR3

Слоты DDR3 DIMM x 2

Каждый модуль DIMM поддерживает

Поддержка DDR3 800/1066/1333(OC)

Не поддерживает зарегистрированные модули

256 МБ / 512МБ / 1ГБ / 2ГБ / 4ГБ DDR3 DIMM and ECC DIMM

Максимальная ёмкость памяти 8ГБ

(Процессор с ФСБ 800 МГц поддерживает только

DDR3 800)

Super I/O

IDE

SATA

Максимальная совместно используемая видео память составляет 1984 МБ (В зависимости от осмия и размера запоминающего устройства)

ITE 8721

Обеспечивает наиболее используемые действующие функциональные

Инициативы по охране окружающей среды,

Аппаратный монитор

Регулятор скорости вентилятора/ монитор возможности Super I/O.

Интерфейс с низким количеством

Функция ITE "Smart Guardian" (Интеллектуальная защита) выводов

Встроенное устройство управления встроенными интерфейсами устройств

Режим "хозяина" шины Ultra DMA 33 / 66 / 100

Поддержка режима PIO 0~4,

Встроенное последовательное устройство управления ATA скорость передачи данных до 3.0 гигабит/с.

Соответствие спецификации SATA версия 2.0.

Локальная сеть

Realtek RTL 8111DL

Звуковая поддержка жесткого

ALC662 диска

Автоматическое согласование 10 / 100 / 1000 Мб/с

Звуковая поддержка High-Definition

5.1канальный звуковой выход

Слоты

Слот PCI

Слот PCI Express x16 x2 x1

Скорость передачи данных ограничена до 250 Мб / с благодаря спецификацию PCIE1.0 x1

40

G41U3G

СПЕЦ

Разъём НГМД x1 гибких магнитных дисках

Разъём Порт подключения Каждый разъём поддерживает 1 Порт подключения

Последовательный порт x1

Разъём IDE

Разъём SATA x1

Каждый разъём поддерживает 2 встроенных интерфейса накопителей x4 Каждый разъём поддерживает 1 устройство SATA

Встроенны й разъём

Контактирующее приспособление Источник питания для вентилятора центрального вентилятора центрального процессора x1 процессора (с функцией интеллектуального вентилятора)

Контактирующее приспособление

Задняя панель средств ввода-выв ода

Открытое контактирующее приспособление CMOS x1

Каждый разъём поддерживает 2 USB 2.0-порта на лицевой панели

Разъем питания (24 вывод) x1

Разъем питания (4 вывод) x1

Клавиатура PS/2

Мышь PS/2

Порт VGA

Порт LAN x1 x1 x1 x1

USB 2.0-порт x2

Гнездо для подключения

USB2.0/USB1.X устройств (по Intel ICH7) наушников x3

Размер панели

192 мм (Ш) X 235 мм (В)

Поддержка

OS


Biostar сохраняет за собой право добавлять или удалять средства обеспечения для OS с или без предварительного уведомления.

41


A

RABIC

تﺎﻔﺻاﻮﻤﻟا

LGA 775

تﺎﻴﻨﻘ ﺗ ﻢﻋﺪﺗ Hyper-Threading / Execute Disable Bit /




Celeron 4xx ﻰﻟإ ﻞﺼ ی دد ﺮﺘ ﺑ

Technology

تﺎﺠﻟﺎﻌﻣIntel Core2Duo / Core2Quad /

(طاو ىﻮ ﺼﻗ: 95و)

ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو

ﺔیﺰآﺮﻤﻟا

ددﺮﺗ 800 / 1066 / 1333 ﺰﺗﺮه ﺎﺠﻴﻣ ﻲﺒﻥﺎﺠﻟا ﻲﻣﺎﻣﻷا ﻞﻗﺎﻨﻟا

Intel G41

Intel ICH7

ﺢﺋاﺮﺸﻟا ﺔﻋﻮﻤﺠﻣ

ةﺮآاذ ةﺪﺣوDDR3 ةﺎﻨ ﻘﻟا ﺔﺝودﺰﻣ

2 دﺪﻋ DDR3 DIMM ﺔﺤﺘﻓ

عﻮﻥ ﻦﻣ ةﺮآاﺬﻟا ﻢﻋﺪﺗDDR3 ﺖیﺎﺑ ﺎﺠﻴﻣ 800 / 1066 /( OC ) 1333 تﺎﻌﺳ ﺔﺤﺘﻓ ﻞآ ﻢﻋﺪﺗDIMM عﻮﻥ ﻦﻣ ةﺮآاذ ﻢﻋﺪﺗ DDR3 ﻞآ ﻢﻋﺪﺗ ﺔﻌﺳ

ةﺮآاﺬ ﻟا ﻖﺋﺎﻗر ﻢﻋﺪﺗ ﻻ DIMM ﻊﻣ ﻖﻓاﻮﺘﺗ ﻻ ﻲﺘﻟا ﻚﻠﺗو ECC

ﺔﺤﺘﻓDIMM عﻮﻥ ﻦﻣ ةﺮآاذ ﻢﻋﺪﺗ DDR3 ﺔﻌﺳ /512 ﺖیﺎﺑ ﺎﺠﻴﻣ

(800 ﺰﺗﺮهﺎ ﺠﻴﻣ ﻊﻣ ةﺪﺣو ﺔ ﺠﻟﺎﻌﻤﻟا ﺔ یﺰآﺮﻤﻟا ﺰﺗﺮﻴهﺎ ﻐﻴﻣ ﻂ ﻘﻓ ﻢﻋﺪ ﺗ

ﺖیﺎﺑ ﺎﺠﻴﺝ 4 و / 2 و / 1 و

DDR3 800)

ﺖیﺎﺑ ﺎﺠﻴﺝ 8 ىﻮﺼﻗ ةﺮآاذ ﺔﻌﺳ

ﺔآﺮﺘﺸﻤﻟا ﻮیﺪﻴﻔﻟا ةﺮآاﺬﻟ ﺔﻌﺳ ﻰﺼﻗأ1984ﺖیﺎﺑ ﺎﺠﻴﻣ

( ادﺎ ﻤﺘﻋا ﻰ ﻠﻋ مﺎﻈﻧ ﻞﻴﻐ ﺸﺘﻟا ﻢﺠﺣو ةﺮآاﺬ ﻟا)

: ﺔﺌﻴﺒﻟا ﻲﻓ ﻢﻜﺤﺘﻟا ﻞﺋﺎﺳو

ةﺰﻬﺝﻷا ﺔﻟﺎﺣ ﺔﻓﺮﻌﻤﻟ ﺐﻗاﺮﻣ

ﺔﺣوﺮﻤﻟا ﺔﻋﺮﺳ ﻲﻓ ﺐﻗاﺮﻣ

ﺔﻔﻴﻇو"Smart Guardian" ﻦﻣ ITE

GMA X4500

ITE 8721

ﺔﻔﻴﻇو ﺮﻓﻮﺗSuper I/O ًﺎﻣاﺪﺨﺘﺳا ﺮﺜآﻷا

ﺔﻴﻨﻘﺗ ﻢﻋﺪ ﺗ

ﺔﻴﻨﻘﺘﺑ ﻞﻗﺎﻥUltra DMA 33 / 66 / 100ﻲﺴﻴﺋر ﻊﺿو

ﻊﺿو ﻢﻋدPIO Mode 0~4

ﻞﺼﺗ تﺎﻋﺮﺴﺑ تﺎﻥﺎﻴﺒﻟا ﻞﻘﻥ

ﺔﻘﺑﺎﻄﻣ

.

ﺔﻴﻥﺎﺙ / ﺖﺑﺎﺠﻴﺝ

راﺪﺹﻹا 2.0.

Low Pin Count Interface

ﻢﻜﺤﺘﻣIDEﻞﻣﺎﻜﺘﻣ

ﻞﻣﺎﻜﺘﻣ

ﺔﻴﺴﻴﺋﺮﻟا ةﺮآاﺬﻟا

تﺎﻣﻮﺳﺮﻟا ﺔﻗﺎﻄﺑ

Super I/O

I DE ﺬﻔﻨﻣ

SATA

ﺔﻴﻧﺎﺛ / ﺖﺑ ﺎﺠﻴﺝ 1 و ﺔﻴﻧﺎﺛ / ﺖیﺎﺑ ﺎﺠﻴﻣ 100 / 10 ﻲﺋﺎﻘﻠﺗ ضوﺎﻔﺗ Realtek RTL 8111DL ﺔﻴﻠﺧاد ﺔﻜﺒﺵ

ﻦﻣ ﻒیﺮﻌﺘﻟا ﻲﻟﺎﻋ تﻮﺼﻟا ﺔﻴﻨﻘﺗ ﻢﻋﺪﺗ

تﻮﺼﻟا جﺮﺨﻟ تاﻮﻨﻗ 5.1

ALC662

ﻲﻟﺎﻋ تﻮﺼﻟا ﻢﻋد

ﻒیﺮﻌﺘﻟا

ﺮ ﺼﺘﻘی تﻻﺪﻌﻣ ﻞ ﻘﻧ تﺎ ﻧﺎﻴﺒﻟا ﻰ ﻟإ 250 ﺎ ﻐﻴﻣ ﺖ یﺎﺑ / ﺔ ﻴﻧﺎﺛ ﺐﺒ ﺴﺑ

تﺎﻔ ﺹاﻮﻤﻟا ﻦﻣ PCIE1.0 X1

42

Asmedia ASM1042 USB3.0

2 دﺪﻋ PCI ﺔﺤﺘﻓ

1 دﺪﻋ PCI Express x16 ﺔﺤﺘﻓ

تﺎﺤﺘﻔﻟا

G41U3G

ﺔﻥﺮﻤﻟا صاﺮﻗﻸﻟ ﻦﻴآﺮﺤﻣ ﻢﻋﺪی

ةﺰﻬﺝأ ﻦﻣ ﻦﻴ ﻨﺙا ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪی IDE

ةﺰﻬﺝأ ﻦﻣ ﺪﺣاو ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪیSATA

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا تاﺰﻴﻬﺠﺗ ﻢﻋﺪی

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟﺎﺑ تﻮﺼﻟا ﺔﻔﻴﻇو ﻢﻋﺪی

ﺔﻔﻴﻇو ﻊﻣ ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺘﻟSmart Fan

مﺎﻈﻨﻟا ﺔﺣوﺮﻤﻟ ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺘﻟ

ﻲﺘﺤﺘﻓ ﺬﻔﻨﻣ ﻞآ ﻢﻋﺪیUSB 2.0ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟﺎﺑ

تﺎﻔﺻاﻮﻤﻟا

1 دﺪﻋ ﺔﻥﺮﻣ صاﺮﻗأ كﺮﺤﻣ ﺬﻔﻨﻣ

1

1

دﺪﻋ

دﺪﻋ

ﺔﻌﺑﺎﻃ ﺬﻔﻨﻣ

ﻲﻠﺴﻠﺴﺗ ﺬﻔﻨﻣ

1

4

دﺪﻋ

دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

IDE ﺬﻔﻨﻣ

SATA ﺬﻔﻨﻣ

ﺔﻴﻣﺎﻣﻷا ﺔﺣﻮﻠﻟا ﺬﻔﻨﻣ

ﻲﻣﺎﻣﻷا تﻮﺼﻟا ﺬﻔﻨﻣ

1 دﺪﻋ ﺔیﺰآﺮﻤﻟا ﺔﺠﻟﺎﻌﻤﻟا ةﺪﺣو ﺔﺣوﺮﻣ ﺔﻠﺹو

1 دﺪﻋ مﺎﻈﻨﻟا ﺔﺣوﺮﻣ ﺔﻠﺹو

1

2

دﺪﻋ

دﺪﻋ

CMOS ﺢﺴﻣ ﺔﻠﺹو

USB 2.0

ﺬﻔﻨﻣ

1 دﺪﻋ ( سﻮﺑد 24 ) ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻣ

1 دﺪﻋ ( ﺲﻴﺑﺎﺑد 4 ) ﺔﻗﺎﻄﻟا ﻞﻴﺹﻮﺗ ﺬﻔﻨﻣ

(Asmedia ASM1042 ﻦﻣ ﻞ ﺒﻗ ) ةﺰﻬﺝﻷا USB3.0

(Intel ICH7 ﻦﻣ ﻞ ﺒﻗ ) ةﺰﻬﺝﻷا USB2.0/USB1.X

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

1 دﺪﻋ

2 دﺪﻋ

2 دﺪﻋ

3 دﺪﻋ

PS/2 ﺢﻴﺗﺎﻔﻣ ﺔﺣﻮﻟ

PS/2 سوﺎﻣ

VGA ﺬﻔﻨﻣ

ﺔﻴﻠﺤﻣ لﺎﺼﺗا ﺔﻜﺒﺵ ﺬﻔﻨﻣ

USB 2.0

ﺬﻓﺎﻨﻣ

USB 3.0

ﺬﻓﺎﻨﻣ

تﻮﺹ ﺲﺒﻘﻣ

ﺢﻄﺱ ﻰﻠﻋ ﺬﻓﺎﻨﻤﻟا

ﺔﺣﻮﻠﻟا

جﺮﺧ / ﻞﺧد ﺬﻓﺎﻨﻣ

ﺔ ﻴﻔﻠﺨﻟا ﺔﺣﻮﻠﻟا

ﺔﺣﻮﻠﻟا ﻢﺠﺣ

نوﺪﺑ وأ رﺎﻄﺧﺈﺑ ﻞﻴﻐﺸﺗ مﺎﻈﻧ يﻷ ﻢﻋﺪﻟا ﺔﻟازإ وأ ﺔﻓﺎﺿإ ﻲﻓ ﺎﻬﻘﺤﺑ

.

رﺎﻄﺧإ

Windows 2000 / XP / Vista / 7 ﻞﻴﻐﺸﺘﻟا ﺔﻤﻈﻧأ ﻢﻋد

43


J

APANESE

仕様

CPU

LGA 775



SpeedStep® / Intel Architecture-64 / Extended

Memory 64 Technology / Virtualization Technologyをサ

Celeron 4xx processor

Hyper-Threading / Execute Disable Bit / Enhanced Intel

ポートします

(最高のワット: 95W)

800 / 1066 / 1333 MHz FSB

チップセット

Intel G41

Intel ICH7

デュアルチャンネルモードDDR3メモリモジュール

DDR3 DIMMスロット x 2

メインメモリ

各

DIMMは 256MB / 512MB / 1GB / 2GB /

4GB DDR3をサポート

DDR3 800/1066/1333(OC)をサポート

登録済み DIMMとECC DIMMはサポートされません

(のCPUのFSBを800 MHzの唯一のDDR3 800をサポートし

最大メモリ容量 8GB

ています )

グラフィック

GMA X4500

ス

ITE 8721

最大の共有ビデオメモリは

（

1984MBです

OSとメモリのサイズにより異なります）

Super I/O

IDE 統合

IDEコントローラ

環境コントロールイニシアチブ、

もっとも一般に使用されるレガシー Super I/O H/Wモニター

機能を採用しています。

低ピンカウントインターフェイス

ファン速度コントローラ / モニター

ITEの「スマートガーディアン」機能

Ultra DMA 33 / 66 / 100バスマスタモード

PIO Mode 0~4のサポート、

SATA 統合シリアル ATAコントローラ

最高

3.0 Gb/秒のデータ転送速度

SATAバージョン2.0仕様に準拠。

LAN Realtek RTL 8111DL 10 / 100 / 1000 Mb/秒のオートネゴシエーション

HDオーディ

オのサポート

ALC662

USB3.0

スロット

ハイデフィニションオーディオのサポート

5.1 チャンネルオーディオアウト

Asmedia ASM1042

データ転送速度は 250に制限されていますMB /秒のPCIE1.0 x1の仕様のためだ

PCIスロット x2

PCI Express x16スロット x1

44

G41U3G

仕様

フロッピーコネクタ x1

プリンタポートコネクタ x1 1つのプリンタポートをサポートします

シリアルポート x1

フロントパネルコネクタ x1

オンボードコフロントオーディオコネクタ x1

ネクタ

システムファンヘッダ x1

CMOSクリアヘッダ x1

各コネクタは 2つのフロントパネルUSB 2.0ポートをサポート

USB 2.0コネクタ x2

します

電源コネクタ (24ピン)

電源コネクタ (4ピン) x1 x1

背面パネル

I/O

PS/2キーボード

PS/2マウス x1 x1

VGAポート x1

LANポート x1

USB 2.0ポート x2

USB2.0/USB1.Xデバイス (で Intel ICH7)

オーディオジャック x3

ボードサイズ 192 mm (幅) X 235 mm (高さ)

OSサポート Windows 2000 / XP / Vista / 7

Biostarは事前のサポートなしにOSサポートを追加または削

除する権利を留保します。

2011/01/07

45

No results