Cisco ME 3800X Series Carrier Ethernet Switch

Cisco ME 3800X Series Carrier Ethernet Switch
Data Sheet
Cisco ME 3800X Series Carrier Ethernet
Switch Router
The Cisco® ME 3800X Series Carrier Ethernet Switch Router is a converged, full-featured aggregation platform
purposely designed for the mobile, business, and residential markets. With low power consumption and high
service scale, this 1-rack-unit (1RU) switch router is optimized for small aggregation and remote point-of-presence
(POP) applications making it a highly cost effective option. The Cisco ME 3800X Series expands the Cisco Carrier
Ethernet aggregation portfolio while complementing the Cisco 7600 Series and ASR 9000 Series routers by
providing a rich and scalable feature set of Layer 2 and Layer 3 VPN services in a compact package.
The Cisco ME 3800X Series (Figure 1) is a small footprint fixed-form-factor platform that comes in the following
configuration:
●
Cisco ME 3800X-24FS with 24 Gigabit Ethernet SFP ports and two 10 Gigabit Ethernet SFP+ ports
Figure 1.
Cisco ME 3800X Series Carrier Ethernet Switch Router
Key Applications
Broadband Aggregation
The Cisco ME 3800X Series supports broadband aggregation for delivering “any-play” services (voice, video, data,
and mobility). Designed to support thousands of subscribers, quality of service (QoS) on the Cisco ME 3800X
Series is capable of scaling to 32,000 queues per device. This high number of queues combined with a more
granular QoS algorithm (three-level hierarchical QoS) results in a greatly enhanced broadband user experience.
This feature-rich Layer 2 and Layer 3 switch router supports a variety of broadband applications including IPTV and
video on demand (VoD), enhancing and extending the Cisco IP NGN architecture.
Pre-Aggregation for Mobile Applications
Deployed as a pre-aggregation platform for mobile backhaul, the Cisco ME 3800X Series can aggregate Cisco
MWR 2941 cell site routers and use MPLS as a transport for Radio Access Network (RAN) backhaul traffic. The
Cisco ME 3800X Series offers timing services, allowing for mobile clocking synchronization from the core of the
network toward the RAN. The Cisco ME 3800X Series can receive clocking information into its Building Integrated
Timing Supply (BITS) interface. It supports synchronous Ethernet (SynchE) with Ethernet Synchronization
Messaging Channel (ESMC) to allow best clock source traceability.
© 2012–2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 1 of 10
Metro Ethernet Aggregation
The Cisco ME 3800X Series is built to meet service provider requirements for Carrier Ethernet aggregation. It is
optimized for the remote central office (CO) and smaller aggregation sites where a fully featured, small-footprint
aggregation platform is needed. The Cisco ME 3800X Series offers service flexibility and delivers Layer 2, IP, and
MPLS transport for advanced Layer 2 and Layer 3 VPN and multicast services.
Key Differentiators
The Cisco ME 3800X Series helps service providers deliver advanced services for residential broadband, mobile,
and Metro Ethernet applications. The highlights of this aggregation platform include the following.
Cisco Carrier Ethernet ASIC
Powered by Cisco’s Carrier Ethernet ASIC, designed specifically for the needs of service providers, the Cisco ME
3800X Series delivers essential Carrier Ethernet technologies including: Hierarchical QoS (H-QoS), MPLS, and
Virtual Private LAN Services (VPLS). The ASIC provides line-rate performance and enables advanced services
including ACL and H-QoS without impacting performance. This Carrier Ethernet ASIC incorporates innovative
traffic management capabilities while providing intelligent packet switching and routing operations.
Service Richness
With the Cisco ME 3800X Series, each service is assigned enhanced QoS and security attributes. The Cisco ME
3800X Series accomplishes advanced per-traffic-class metering and offers bidirectional packets and bytes
statistics. The service offering is enhanced with rich operations, administration, and management (OAM)
functionality including: Layer 2 Connectivity Fault Management (CFM), IP SLA for Layer 3, and MPLS OAM.
Service Scale
The Cisco ME 3800X Series delivers unmatched service scalability in a 1RU footprint. With support for 256,000
MAC addresses and 8000 bridge domains, this switch router delivers high performance and high scale for point-topoint and multipoint VPN services. A total buffer size of 352 MB is available to provide per service advanced QoS
capabilities.. Such amount of buffer is required when stringent applications like financial or video must be protected
against the impact of 10 Gbps to 1 Gbps speed mismatch. The quantity of statistical counters enables the Cisco
ME 3800X Series to provide a high level of service metering and monitoring throughout its range of scale.
High-Performance Hardware
The Cisco ME 3800X Series provides two slots for hot-swappable and redundant power supply. Three fans are
integrated into each power supply, providing fan redundancy. High Availability is also achieved on the Cisco ME
3800X Series through proactive diagnostic tools including Generic On-Line Diagnostics (GOLD) and Onboard
Failure Logging (OBFL). These tools help service providers avoid potential problems before they occur and
troubleshoot and diagnose once identified.
Table 1 lists the hardware parts available for Cisco ME 3800X Series.
Table 1.
Hardware Components for Cisco ME 3800X Series
Part Number
Description
ME-3800X-24FS-M
Cisco ME 3800X-24FS Ethernet Carrier Ethernet Switch Router
ME-3800X-24FS-M=
Spare Cisco ME 3800X-24FS Ethernet Carrier Ethernet Switch Router
PWR-ME3KX-AC
Cisco ME 3600X/ME 3800X Series field- replaceable AC power supply and fan module
PWR-ME3KX-DC
Cisco ME 3600X/ME 3800X Series field- replaceable DC power supply and fan module
PWR-ME3KX-AC=
Cisco ME 3600X/ME 3800X Series spare field-replaceable AC power supply and fan module
© 2012–2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 2 of 10
Part Number
Description
PWR-ME3KX-DC=
Cisco ME 3600X/ME 3800X Series spare field-replaceable DC power supply and fan module
ME-FANTRAY=
Cisco ME 3600X/ME 3800X Series spare fan tray. The fan tray is required in the second slot when only one power
supply is in the system.
RCKMNT-ME3KX-ETSI
ETSI Rack mount Option for the Cisco ME 3600X/ME 3800X Series
RCKMNT-ME3KX-23IN
23” Rack mount Option for Cisco ME 3600X//ME 3800X Series
RCKMNT-ME3KX-ANG
Angled Rack mount for Cisco ME 3600X/ME 3800X Series
RCKMNT-ME3KX-ETSI=
Spare ETSI Rack mount Option for the Cisco ME 3600X/ME 3800X Series
RCKMNT-ME3KX-23IN=
Spare 23” Rack mount Option for Cisco ME 3600X//ME 3800X Series
RCKMNT-ME3KX-ANG=
Spare Angled Rack mount for Cisco ME 3600X/ME 3800X Series
RCKMNT-ME3KX-19IN=
Spare 19” Rack mount Option for Cisco ME 3600X//ME 3800X Series
MEM-ME3K-2GB
Cisco ME 3600X and ME3800X SD Memory Card 2GB
MEM-ME3K-2GB=
Cisco ME 3600X and ME3800X SD Memory Card 2GB Spare
MEM-ME3K-4GB
Cisco ME 3600X and ME3800X SD Memory Card 4GB
MEM-ME3K-4GB=
Cisco ME 3600X and ME3800X SD Memory Card 4GB Spare
The Cisco ME 3800X Series supports a wide range of SFP and SPF+ optic modules. Table 2 lists their part
numbers.
Table 2.
SFP and SFP+ Modules Supported with Cisco ME 3800X Series
Part number
SFP
GLC-FE-100FX, GLC-FE-100EX, GLC-FE-100ZX, GLC-FE-100LX, GLC-FE-100BX-U, GLC-FE-100BX-D,
GLC-LH-SM, GLC-SX-MM, GLC-ZX-SM, GLC-SX-MMD, GLC-LH-SMD, GLC-EX-SMD, GLC-T, GLC-BX-U (CPN
10-2094-02), GLC-BX-D (CPN 10-2093-02),, SFP-GE-L, SFP-GE-S, SFP-GE-T, CAB-SFP-50CM, CWDM-SFP1470, CWDM-SFP-1490, CWDM-SFP-1510, CWDM-SFP-1530, CWDM-SFP-1550, CWDM-SFP-1570, CWDMSFP-1590, CWDM-SFP-1610, DWDM-SFP-6061, DWDM-SFP-5979, DWDM-SFP-5898, DWDM-SFP-5817,
DWDM-SFP-5736, DWDM-SFP-5655, DWDM-SFP-5575, DWDM-SFP-5413, DWDM-SFP-5494, DWDM-SFP5332, DWDM-SFP-5252, DWDM-SFP-5172, DWDM-SFP-5092, DWDM-SFP-5012, DWDM-SFP-4931, DWDMSFP-4851, DWDM-SFP-4772, DWDM-SFP-4692, DWDM-SFP-4612, DWDM-SFP-4532, DWDM-SFP-4453,
DWDM-SFP-4373, DWDM-SFP-4294, DWDM-SFP-4214, DWDM-SFP-4134, DWDM-SFP-4056, DWDM-SFP3977, DWDM-SFP-3898, DWDM-SFP-3819, DWDM-SFP-3739, DWDM-SFP-3661, DWDM-SFP-3582, DWDMSFP-3504, DWDM-SFP-3425, DWDM-SFP-3346, DWDM-SFP-3268, DWDM-SFP-3190, DWDM-SFP-3112,
DWDM-SFP-3033, DWDM-SFP-6141
SFP+
SFP-10G-SR, SFP-10G-LR, SFP-10G-ER, SFP-10G-ZR, SFP-10G-LRM, SFP-H10GB-CUxM, DWDM-SFP10G61.41, DWDM-SFP10G-60.61, DWDM-SFP10G-59.79, DWDM-SFP10G-58.98, DWDM-SFP10G-58.17, DWDMSFP10G-57.36, DWDM-SFP10G-56.55, DWDM-SFP10G-55.75, DWDM-SFP10G-54.94, DWDM-SFP10G-54.13,
DWDM-SFP10G-53.33, DWDM-SFP10G-52.52, DWDM-SFP10G-51.72, DWDM-SFP10G-50.92, DWDM-SFP10G50.12, DWDM-SFP10G-49.32, DWDM-SFP10G-48.51, DWDM-SFP10G-47.72, DWDM-SFP10G-46.92, DWDMSFP10G-46.12, DWDM-SFP10G-45.32, DWDM-SFP10G-44.53, DWDM-SFP10G-43.73, DWDM-SFP10G-42.94,
DWDM-SFP10G-42.14, DWDM-SFP10G-41.35, DWDM-SFP10G-40.56, DWDM-SFP10G-39.77, DWDM-SFP10G38.98, DWDM-SFP10G-38.19, DWDM-SFP10G-37.40, DWDM-SFP10G-36.61, DWDM-SFP10G-35.82, DWDMSFP10G-35.04, DWDM-SFP10G-34.25, DWDM-SFP10G-33.47, DWDM-SFP10G-32.68, DWDM-SFP10G-31.90,
DWDM-SFP10G-31.12, DWDM-SFP10G-30.33
© 2012–2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 3 of 10
Flexible Software Options
The Cisco ME 3800X Series supports the Cisco IOS® Software Activation feature. With this feature Cisco IOS
Software feature sets can be activated by Cisco software licenses, enabling a “pay as services grow” model. This
model allows service providers to invest in software resources only when their business needs it. The Cisco
ME3800X offers four different Cisco IOS Software licenses:
●
The Metro Ethernet Services license offers advanced QoS, Carrier Ethernet Layer 2 features, and
Ethernet OAM capability.
●
The Metro IP Services license offers advanced QoS, Carrier Ethernet Layer 2 features, Ethernet OAM,
Layer 3 features for advanced IP routing protocols, multi-VPN routing, and Forwarding Customer Edge
(multi-VRF CE) capabilities.
●
The Metro Aggregation Services license adds the following capabilities to the METRO IP ACCESS image:
MPLS, EoMPLS pseudowires, VPLS, MPLS traffic engineering, Fast Reroute, and MPLS VPN support.
●
The Services Scalability license enables full scalability for Layer 2, IP routing, MPLS resources and the
use of Switch Management Database (SDM) templates.
Table 3 lists the key feature in the Cisco IOS licenses for the Cisco ME 3800X Series.
Table 3.
Feature Set in Cisco ME 3800X Series Licenses
Metro Ethernet Services
Metro IP Services
Metro Aggregation Services
Layer 2: 802.1d, 802.1q
All features in METROETHSERVICES plus:
All features in: METROAGGRSERVICES plus:
Ethernet Virtual Circuit (EVC)
IP routing (RIP, OSPF, EIGRP, IS-IS, BGP)
MPLS
Ethernet OAM (802.1ag, 802.3ah, E-LMI,
1731 PM)
PIM (SM, DM, SSM), SSM mapping
MPLS traffic engineering (TE) and Fast Reroute
(FRR)
MST, REP, Flexlink, G.8032
Bidirectional Forwarding Detection (BFD)
MPLS OAM
Synchronous Ethernet, Ethernet
Synchronization messaging Channel
(ESMC) Synchronization Status Messages
(SSM)
Multi-VRF CE (VRF lite) with service
awareness (ARP, ping, SNMP, syslog,
traceroute, FTP, TFTP)
MPLS VPN
Multicast VPN (MVPN)
Ethernet over MPLS (EoMPLS)
Virtual Private LAN Services (VPLS), Hierarchical
VPLS (H-VPLS)
Pseudowire redundancy
Switch Database Management (SDM) templates
(with the Scalability license only)
Table 4 provides brief descriptions of the Cisco ME 3800X Series software options.
Table 4.
Cisco ME 3800X Series Software Options
Part Number
Product Name
License Options
ME3800X-E
Cisco ME3800X METRO ETHERNET SERVICES Software Paper License
ME3800X-I
Cisco ME 3800X Series METRO IP SERVICES Software Paper License
ME3800X-A
Cisco ME 3800X Series METRO AGGREGATION SERVICES Software Paper License
ME3800X-S
Cisco ME 3800X Series SCALED Software Paper License
Product Activation Keys
ME3800X-LIC=
Product activation keys for ME3800X Series (Paper Delivery)
L-ME3800X-LIC=
Product activation keys for ME3800X Series (E-Delivery)
© 2012–2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 4 of 10
Part Number
Product Name
License Upgrade Options
ME3800X-I-A
Cisco ME 3800X Series METRO IP2 AGGREGATION SERVICES Software Paper License
L-ME3800X-I
Cisco ME 3800X Series METRO IP SERVICES Software E License
L-ME3800X-A
Cisco ME 3800X Series METRO AGGREGATION SERVICES Software E License
L-ME3800X-I-A
Cisco ME 3800X Series METRO IP2 AGGREGATION SERVICES Software E License
L-ME3800X-S
Cisco ME 3800X Series SCALED Software E License
Software Options
S380XVT-12252EY
Cisco ME 380X Series IOS UNI. W/O CRYPTO
S380XVK9T-12252EY
Cisco ME 380X Series IOS UNIVERSAL
S380XVT-15102EY
Cisco ME 380X Series IOS UNIVERSAL W/O CRYPTO TAR – Release 15.1(2)EY
S380XVK9T-15102EY
Cisco ME 380X Series IOS UNIVERSAL TAR – Release 15.1(2)EY
S380XVK9T-15202S
Cisco ME 380X SERIES IOS UNIVERSAL TAR – Release 15.2(2)S
S380XVT-15202S
Cisco ME 380X SERIES IOS UNIVERSAL W/O CRYPTO TAR – Release 15.2(2)S
S380XVK9T-15204S
Cisco ME 380X SERIES IOS UNIVERSAL TAR – Release 15.2(4)S
S380XVT-15204S
Cisco ME 380X SERIES IOS UNIVERSAL W/O CRYPTO TAR – Release 15.2(4)S
S380XVK9T-15301S
Cisco ME 380X SERIES IOS UNIVERSAL TAR – Release 15.3(1)S
S380XVT-15301S
Cisco ME 380X SERIES IOS UNIVERSAL W/O CRYPTO TAR – Release 15.3(1)S
S380XVK9T-15302S
Cisco ME 380X SERIES IOS UNIVERSAL TAR – Release 15.3(2)S
S380XVT-15302S
Cisco ME 380X SERIES IOS UNIVERSAL W/O CRYPTO TAR – Release 15.3(2)S
Key Features
Table 5 lists the features of the Cisco ME 3800X Series.
Table 5.
Features
Features
Ethernet Services
● Ethernet Virtual Connections (EVCs) for:
◦
◦
◦
◦
◦
QinQ
Selective QinQ
Inner and Outer VLAN classification
EVC Push and Pop rewrite
EVC local connect
● IEEE bridging
● Layer 2 Protocol Tunneling (L2PT)
● Hierarchical VPLS (H-VPLS), Virtual Private LAN Service (VPLS), VPLS Border Gateway Protocol [BGP] signaling
● Virtual Private Wire Service (VPWS), Ethernet over MPLS (EoMPLS), pseudowire redundancy
● Ethernet Data Plane loopback (Terminal and Facility)
© 2012–2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 5 of 10
Features
Layer 3 Services
● Layer 3 Routing
● IPv4 Routing (Border Gateway Protocol [BGP], Intermediate System-to-Intermediate System [IS-IS], and Open Shortest Path First [OSPF]),
Hot Standby Router Protocol (HSRP), Virtual Router Redundancy Protocol (VRRP)
● IPv6 Unicast Routing (Border Gateway Protocol [BGP], Intermediate System-to-Intermediate System [IS-IS], and Open Shortest Path First
[OSPF])
● IPv6 Provider Edge (6PE)
● IPv6 VPN over MPLS (6VPE)
● MPLS
● Label Distribution Protocol (LDP), Targeted LDP (T-LDP), Resource Reservation Protocol (RSVP), Differentiated Services (DiffServ)-aware
traffic engineering, MPLS L3VPN
● MPLS traffic engineering (including TE-FRR)
● Carrier Supporting Carrier (CsC) with BGP as CE-PE routing protocol
● BGP with label distribution ( RFC3107)
● Routed Pseudowire
● Integrated Routing and Bridging (IRB)
● Policy Based Routing (PBR)
QoS
● Up to 32,000 egress queues per system
● Class-Based Weighted Fair Queuing (CBWFQ)
● Priority Queuing
● 2-rate 3-color (2R3C) ingress Policing, Egress Policing (1R2C) for LLQ
● Ingress and Egress marking (CoS, DSCP, MPLS Experimental Bits)
● Egress shaping per port and per queue
● Modular QoS CLI (MQC)
● 3-level H-QoS
● Classification based on inner and outer class of service (CoS) or VLAN ID
● Copy inner to outer CoS
● WRED
● IPV6 QoS
● Table Map
Multicast
● IPv4 Multicast
● Protocol Independent Multicast sparse mode (PIM-SM), PIM Source Specific Multicast (PIM SSM), PIM SSM mapping
● Internet Group Management Protocol Versions 1, 2, and 3 (IGMPv1, v2, and v3)
● IGMPv1, v2, and v3 snooping on switchport, EVC interfaces and Pseudowires
● PIM Snooping
● IPv4 multicast per VRF lite
● Multicast VPN (MVPN)
Security
● Authentication, authorization, and accounting (AAA); TACACS+; Secure Shell (SSH) Protocol; MAC limiting per Ethernet flow point (EFP) or
bridge domain; unicast, multicast, and broadcast storm control blocking on any interface or port
● Layer 2 ACLs
● Layer 3 ACLs for IPv4 and IPv6
● ACL on switchport, EVC and routed interfaces
● Control Plane Policing
● DHCP snooping with option 82
● Dynamic Arp Inspection (DAI)
● SPAN
● 802.1x Authenticator
© 2012–2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 6 of 10
Features
Availability
● Resilient Ethernet Protocol (REP)
● ITU-T G.8032 Ethernet Ring Protection Switching
● IEEE 802.1w Rapid Spanning Tree Protocol (RSTP)
● IEEE 802.1s Multiple Spanning Tree Protocol (MST)
● Per-VLAN Rapid Spanning Tree (PVRST+)
● MPLS TE Fast Reroute
● BFD triggered Fast Reroute
● Flexlink
● BFD for Static,ISIS, OSPF, BGP
● BFD over Switched Virtual Interface (SVI)
● 802.3ad Link Aggregation Bundles
● MPLS IGP-LDP Synchronization
● LACP 1-1 redundancy with Fast Switchover
● EoMPLS Link Path Through
OAM
● CFM (802.1ag)
● Link OAM (802.3ah)
● MPLS OAM
● E-LMI (CE and PE)
● 1731 Performance Monitoring (ETH-DM , ETH-SLM) with concurrent and on demand operations
Manageability
● Simple Network Management Protocol (SNMP)
● MIBs
● RMON
● Cisco Active Network Abstraction (ANA) 3.7.1: physical and logical inventory, service-level views with support for the following technologies:
OSPF, BGP, EtherChannel, routing, Link Aggregation Group (LAG), ACL, Cisco Discovery Protocol, Address Resolution Protocol (ARP)
● CiscoWorks Lan Management Solution (LMS) 3.2
● Embedded Event Manager (EEM 4.0)
● 60 days build-in evaluation licenses
● Switch Database Management (SDM)
● External SD Flash Cards support
Timing
● ITU-T Synchronous Ethernet (syncE) with Ethernet Synchronization Messaging Channel (ESMC)
● Synchronization Status Messages (SSM)
Product Specifications
Tables 6 through 8 list product, power, and environmental specifications for the Cisco ME 3800X Series. Table 9
lists standards and protocols, and Table 10 gives safety and compliance information.
Table 6.
Product Specifications
Description
Cisco ME 3800X-24FS
Performance
Forwarding bandwidth full duplex: Cisco ME 3800X-24FS AC or DC: 44 Gbps
Forwarding rate: Cisco ME 3800X-24FS AC or DC: 65 Mpps
Configurable maximum transmission unit (MTU) of up to 9,800 bytes, for bridging on Gigabit and 10 Gigabit
Memory
DRAM: 1GB
Flash: 64MB
Packet buffer: 352MB
External SD Flash: 2GB and 4GB SD Flash cards (optional)
© 2012–2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 7 of 10
Description
Cisco ME 3800X-24FS
Connectors and cabling
SFP ports:
● 10/100/1000BASE-T SFP-based ports: RJ-45 connectors, 4-pair Category 5 UTP cabling
● 100BASE-FX and -LX: Duplex LC receptacle fiber connectors (multimode and single-mode)
● 100BASE-BX: Single-fiber LC receptacle connector (single-mode fiber)
● 100BASE-EX: SFP module for 100 Mb port, 1310 nm wavelength, 40 km over single-mode fiber
● 100BASE-ZX: SFP module for 100 Mb port, 1550 nm wavelength, 80 km over single-mode fiber
● 1000BASE-BX: Single-fiber LC receptacle connector (single-mode fiber)
● 1000BASE-SX, -LX/LH, -EX and -ZX and CWDM and DWDM: Duplex LC receptacle fiber connectors (multimode
and single-mode fiber)
SFP+ port:
● 10GBASE-LR, -SR, -ER, -ZR, –LRM, DWDM and -H10GB-CUxM where x = 1, 3, 5 meters
● SFP+ port supports 1000BASE-X except 1000BASE-T.
Management console port: RJ-45-to-DB9 cable for PC connections
Management 10/100/1000 Ethernet: RJ-45 connector
BITS and alarm ports: RJ-45 connector
Indicators
Per-port status LEDs: Link integrity, port disabled, and activity indications
Power input /output status LED
Alarm status LED
SynchE status LED
System status LED
Dimensions
All SKUs 1.72-in. x 17.50-in. x 20.33-in. (H x W x D)
Weight
ME-3800X-24FS-M 14.50 lb (6.57 kg)
PWR-ME3KX-AC 2.90 lb (1.31 kg)
PWR-ME3KX-DC 3.10 lb (1.40 kg)
ME-FANTRAY 1.65 lb (0.74 kg)
Mean time between
failure (MTBF)
ME3800X-24FS-M: 185,349 hours
PWR-ME3KX-DC: 319,000 hours (48V input at 40ºC)
PWR-ME3KX-AC: 328,000 hours (120V at 40ºC), 342,000 hours (230V at 40ºC)
ME-FANTRAY: 2,177,000 hours (12V input at 40ºC)
Table 7.
Power Specifications
Description
Cisco ME 3800X-24FS
Power consumption
Cisco ME 3800X-24FS, one AC and one FT:
155W (typical), 228W (maximum), 530 Btus per hour (typical), 779 Btus per hour (maximum)
Cisco ME 3800X-24FS, two AC:
163W (typical), 233W (maximum), 557 Btus per hour (typical), 796 Btus per hour (maximum)
Cisco ME 3800X-24FS, one DC and one FT:
156W (typical), 246W (maximum), 533 Btus per hour (typical), 840 Btus per hour (maximum)
Cisco ME 3800X-24FS, two DC:
161W (typical), 238W(maximum), 550 Btus per hour (typical), 813 Btus per hour (maximum)
AC input voltage and
frequency
100–240VAC, 50–60Hz
DC input voltages
18V to 32VDC, 36V to 72VDC
© 2012–2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 8 of 10
Table 8.
Environmental Specifications
Cisco ME 3800X Series Environment Specification (NEBS)
Operating
environment and
altitude1
Normal operating temperature and altitudes:
0 to +50ºC, up to 1000 feet (300m)
0 to +45ºC, up to 6000 feet (1800m)
0 to +40ºC, up to 10,000 feet (3000m)
Short-term2 exceptional conditions:
0 to +60ºC, up to 1000 feet (300m)
0 to +55ºC, up to 6000 feet (1800m)
0 to +50ºC, up to 10,000 feet (3000m)
0 to +45ºC, at sea level with single fan failure
3
Relative humidity
5% to 95%, non-condensing
Acoustic noise 4
LpA: 43 dB typical, 45 dB maximum
LwA: 5.4 Bel typical, 5.6 Bel maximum
Storage environment
Temperature: –25 to +70ºC altitude: 15,000 ft
1. Switch supports –5°C operation provided that it powers up at ambient equal to or greater than 0°C. SFP-10G-LRM SFP+ module may only be
used from 0°C. GLC-T SFP may only be used from 0 to +50°C, up to 1000 feet (300m), for normal operating and short-term conditions
2. Not more than the following in a one-year period: 96 consecutive hours, or 360 hours total, or 15 occurrences
3. This may be limited by specification of optical modules
4. Acoustic noise is measured per ISO 7779 and declared per ISO 9296
Table 9.
Standards and Protocols
Standards and protocols
● IEEE 802.1s
● IEEE 802.1w
● IEEE 802.1Q VLAN
● IEEE 802.3 10BASE-T
● IEEE 802.3ad
● IEEE 802.3ah
● IEEE 802.3u 100BASE-T
● IEEE 802.3ab 1000BASE-T
● IEEE 802.1ag
● IEEE 802.3x full duplex on 10BASE-T, 100BASE-TX, and
1000BASE-T ports
● IEEE 802.1D Spanning Tree Protocol
● IEEE 802.3z 1000BASE-X
● BFD for OSPF, IS-IS, BGP, HSRP, EIGRP
● IEEE 802.1p CoS classification
● IP routing: Static, RIP versions 1 and 2, EIGRP, OSPF, BGPv4,
PIM-SM, and PIM-DM (metro IP access only)
● Management: SNMP versions 1, 2, and 3
● MEF 9 & 14 certified
● MEF CE 2.0 certified (E-LINE, E-LAN, E-TREE)
Table 10.
Safety and Compliance
Type
Standards
Electromagnetic
FCC Part 15 Class
Emissions Compliance
● EN 55022 Class A (CISPR22 Class A)
● EN 55024
● EN 300 386
● VCCI Class A
● AS/NZS 3548 Class A or AS/NZS CISPR22 Class A
● KCC
● CE Marking
© 2012–2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 9 of 10
Type
Standards
● UL 60950-1
● UL to CAN/CSA 22.2 No.60950-1
Safety
● TUV/GS to EN 60950-1 with all Amendments
● CB to IEC 60950-1 with all country deviations
● NOM to NOM-019-SCFI (through distributors)
● CE Marking
● CCC
GR-63-CORE, GR-1089-CORE – Level 3, Type 2
NEBS
Verizon’s FOC Certification on optical SFPs
EN 300 019 – Storage: Class 1.2, Transportation: Class 2.3, In-Use: Class 3.2
ETSI
Service and Support
Cisco offers a wide range of services programs to accelerate customer success. These innovative services programs
are delivered through a unique combination of people, processes, tools, and partners, resulting in high levels of
customer satisfaction. Cisco services help you protect your network investment, optimize network operations, and
prepare your network for new applications to extend network intelligence and the power of your business. For more
information about Cisco services, refer to Cisco Technical Support Services or Cisco Advanced Services.
Cisco is committed to minimizing your total cost of ownership. Cisco offers a portfolio of technical support services to
help ensure that Cisco products operate efficiently, remain highly available, and benefit from the most up-to-date
system software. The services and support programs described in Table 11 are available as part of the Cisco Carrier
Ethernet Switching Service and Support solution and are available directly from Cisco and through resellers.
Table 11.
Service and Support
Advanced Services
Features
Benefits
Cisco Total Implementation Solutions (TIS),
available directly from Cisco
● Project management
● Site survey, configuration, and deployment
● Supplement existing staff
● Help ensure functions meet needs
Cisco Packaged TIS, available through
resellers
● Installation, text, and cutover
● Training
● Mitigate risk
● Major moves, adds, and changes
● Design review and product staging
Cisco SP Base Support and Service ProviderBased Onsite Support, available directly from
Cisco
Cisco Packaged Service Provider- Based
Support, available through resellers
● 24-hour access to software updates
● Web access to technical repositories
● Telephone support through the Cisco
Technical Assistance Center (TAC)
● Advance Replacement of hardware parts
Printed in USA
© 2012–2013 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
● Facilitate proactive or expedited problem
resolution
● Lower total cost of ownership by taking
advantage of Cisco expertise and
knowledge
● Minimize network downtime
C78-601950-10
03/13
Page 10 of 10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement