Installation and Getting Started Guide for the ProCurve 1700

Installation and Getting Started Guide for the ProCurve 1700
Installation and Getting
Started Guide
ProCurve Switch 1700-8
ProCurve Switch 1700-8
Installation and Getting
Started Guide
© Copyright 2006, 2007 Hewlett-Packard
Development Company L.P.
The information contained herein is
subject to change without notice.
This document contains proprietary
information, which is protected by
copyright. No part of this document may
be photocopied, reproduced, or
translated into another language without
prior written consent of Hewlett-Packard.
Publication Number
March 2007
Applicable Product
ProCurve Switch 1700-8 (J9079A)
Before installing and operating this
product, please read the “Installation
Precautions:” in Chapter 2, “Installing the
Switch”, and the safety statements in
Appendix B, “Safety and EMC Regulatory
A PARTICULAR PURPOSE. HewlettPackard shall not be liable for errors
contained herein or for incidental or
consequential damages in connection
with the furnishing, performance, or use
of this material.
The only warranties for HP products and
services are set forth in the express
warranty statements accompanying such
products and services. Nothing herein
should be construed as constituting an
additional warranty. HP shall not be liable
for technical or editorial errors or omissions contained herein.
Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished
by Hewlett-Packard.
See the Customer Support/Warranty
booklet included with the product.
A copy of the specific warranty terms
applicable to your Hewlett-Packard
products and replacement parts can be
obtained from your HP Sales and Service
Office or authorized dealer.
1 Switch Overview
Switch Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Switch Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
2 Installing the Switch
Included Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Installation Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Installation Precautions: . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
1. Prepare the Installation Site . . . . . . . . . . . . . . . . . . . . . . 2-5
2. Verify the Switch Passes Self Test . . . . . . . . . . . . . . . . . 2-6
3. Mount the Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
4. Connect the Switch to a Power Source . . . . . . . . . . . . . 2-8
5. Connect the Network Cables . . . . . . . . . . . . . . . . . . . . . 2-9
3 Configuring the Switch
Initial Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Changing PC’s IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Where to Go From Here . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
4 Troubleshooting
Basic Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Diagnosing With the LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Forgotten the IP Address or Password . . . . . . . . . . . . . . . 4-4
Hardware Diagnostic Tests . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Testing the Switch by Resetting It . . . . . . . . . . . . . . . . . . 4-4
HP Customer Support Services . . . . . . . . . . . . . . . . . . . . . 4-5
Before Calling Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
A Specifications
Physical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
B Safety and EMC Regulatory Statements
Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
EMC Regulatory Statements . . . . . . . . . . . . . . . . . . . . . . . B-13
C Recycle Statements
Waste Electrical and Electronic Equipment (WEEE)
Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
Switch Overview
Switch Hardware Features
The ProCurve Switch 1700-8 (J9079A) is a multiport switch that can
be used to build high-performance switched workgroup networks.
This switch is a store-and-forward device that offers low latency for
high-speed networking.
10/100Base-TX RJ-45 ports
(all ports have the HP Auto-MDIX feature)
Link/Act, FDx, and Spd
LEDs for each port
10/100/1000 Base-T
RJ-45 ports
ProCurve Switch 1700-8
Switch Ports
The switch has 7 auto-sensing 10/100Base-TX ports and 1 autosensing 10/100/1000Base-T auto MDI/MDI-X RJ-45 port. With this
switch you can directly connect computers, printers, and servers to
provide dedicated bandwidth to those devices, and you can build a
switched network infrastructure by connecting it to hubs, other
switches, or routers. In addition, the switch offers network
management capabilities.
Switch Overview
Switch Hardware Features
The front panel of the switch provides status LEDs for system
monitoring. The following table details the functions of the various
System LED
The switch is receiving power.
The switch is NOT receiving power.
Port LED
(green –
overlaid with
the port
The port is enabled and receiving a link indication
from the connected device.
The port has no active network cable connected,
or is not receiving link signal.
Indicates that there is network activity on the
Indicates the port is operating at full duplex
Indicates the port is operating at half duplex
• Ports 1-7: Indicates the port is operating at
100 Mbps.
• Port 8: Indicates the port is operating at 100 or
1000 Mbps.
• Ports 1-7: Indicates the port is operating at
10 Mbps.
• Port 8: Indicates the port is operating at
10 Mbps.
Switch Overview
Switch Hardware Features
Switch Features
The features of the ProCurve Switch 1700-8 include:
7 auto-sensing 10/100Base-TX ports and 1 auto-sensing 10/100/
1000Base-T RJ-45 port.
plug-and-play networking—all ports are enabled—just connect
the network cables to active network devices and your switched
network is operational.
IEEE 802.3ab Auto MDI /MDI-X on all twisted-pair ports, meaning
that all connections can be made using straight-through twistedpair cables. Cross-over cables are not required, although they will
also work. The pin operation of each port is automatically
adjusted for the attached device: if the switch detects that a 10/
100 Mbps switch or hub is connected to the port, it configures the
port as MDI; if the switch detects that a 10/100 Mbps end-node
device is connected to the port, it configures the port as MDI-X.
automatic learning of the network addresses in each switch’s
8000- address forwarding table.
automatically negotiated full-duplex operation for all 10/100/
1000Base-T RJ-45 ports when connected to other autonegotiating devices.
easy management of the switch through several available
Web browser interface — an easy to use built-in graphical
interface that can be accessed from common Web browsers.
ProCurve Manager (PCM) — allows network administrators
to discover and map the ProCurve Switch 1700 within their
network and launch the ProCurve Switch 1700's built-in
graphical interface from within PCM to configure the switch.
support for up to 64 IEEE 802.1Q-compliant VLANs so you can
divide the attached end nodes into logical groupings that fit your
business needs.
Switch Overview
Switch Hardware Features
support for up to 4 trunks so you to assign physical links to one
logical link (trunk) that functions as a single, higher-speed link
providing dramatically increased bandwidth.
support for many advanced features to enhance network
performance—for a description, see the Management and
Configuration Guide.
download of new switch software for product bug fixes.
supports pass through (flooding) of spanning tree BPDUs so that
upstream devices on the network which support Spanning Tree
Protocol can detect loops that exist on the ProCurve Switch 1700
Installing the Switch
The ProCurve Switch 1700-8 is easy to install. It comes with rubber
feet that can be attached so the switch can be securely located on a
horizontal surface. This chapter shows how to install the switch.
Included Parts
The following components ship with a ProCurve Switch 1700-8:
■ ProCurve Switch 1700-8 Installation and Getting Started Guide
(5991-6267), this manual
■ Customer Support/Warranty booklet
■ Four rubber feet
■ AC power adapter, one of the following:
Australia/New Zealand
United Kingdom/Hong Kong/Singapore
United States/Canada/Taiwan
Universal Adapter 1
Installing the Switch
Included Parts
A country specific power cord is required for use with this adapter. The
power cord part numbers are as follows:
Power Cord
Part Number
South Africa
United States/Canada/Philippines
Austrilia/New Zealand
United Kingdom/Hong Kong/Singapore/Malaysia
Installing the Switch
Installation Procedures
Installation Procedures
Follow these easy steps to install your switch. The rest of this chapter
provides details on these steps.
Prepare the installation site. Make sure of the following:
• the network cabling is the correct type and length. See page
See page 2-4 for installation precautions.
Verify the switch passes self test. This is a simple process of
plugging the switch into a power source and observing that the
LEDs on the switch’s front panel show correct operation. See
page 2-7.
Mount the switch. The switch can be mounted on any horizontal
Connect power to the switch. Once the switch is mounted, plug
in the AC power adapter. See page 2-8.
Connect the network devices. Using the appropriate network
cables, connect computers, servers, printers and other peripherals, and other network devices including other switches, hubs,
or routers to the switch ports. See page 2-9.
At this point, the switch is fully installed and your network should be
up and running. See the rest of this chapter if you need more detailed
information on any of these installation steps.
Installing the Switch
Installation Procedures
Installation Precautions:
Follow these precautions when installing your switch.
Make sure you use the power adapter supplied with the
switch to connect it to an AC power source.
When installing the switch, since the unit does not have
an On/Off power switch, an AC power outlet must be
located near the switch and should be easily accessible
in case the switch needs to be powered off.
Make sure the switch does not overload the power
circuits, wiring, and over-current protection. To
determine the possibility of overloading the supply
circuits, add together the amperage ratings of all devices
installed on the same circuit as the switch and compare
the total with the rating limit for the circuit. The
maximum amperage ratings are usually printed on the
devices near the AC power connectors or power adapter
Do not install the switch in an environment where the
operating ambient temperature might exceed 40 °C
(104 °F).
Make sure the air flow around the sides of the switch is
not restricted.
Installing the Switch
Installation Procedures
1. Prepare the Installation Site
Cabling Infrastructure - To ensure proper operation when
installing the switch into a network, make sure that the current
cables are suitable for 10Base-T, 100Base-TX, or 1000Base-T
Be sure to follow the guidelines below to ensure proper operation
when installing the switch into a network:
Cable type: Unshielded twisted pair (UTP) or shielded
twisted pair (STP) cables with RJ-45 connectors, maximum
length 100 meters (328 ft); Category 3 or better for 10Base-T,
Category 5 or better for 100Base-TX, and Category 5, 5e, or 6
for 1000Base-T.
Protection from radio frequency interference emissions.
Use electrical surge suppression.
Use safe connections with no damaged cables, connectors or
Installation Location - Before installing the switch, plan its
location and orientation relative to other devices and equipment.
At the front of the switch, leave at least 7.6 cm (3 inches) of space
for the twisted-pair cabling. At the back of the switch, leave at least
2.6 cm (1 inch) of space for the adapter’s power cord.
Installing the Switch
Installation Procedures
2. Verify the Switch Passes Self Test
Before mounting the switch in its network location, you should first
check that it is working properly by plugging it into a power source
and verifying that it passes its self test.
Connect the adapter’s power cord to the power connector on the
back of the switch, and then plug the AC power adapter into a
nearby properly grounded electrical outlet. If the power adapter
part number 5188-6700 is used; first plug the country specific
power cord into the adapter, and then into the AC power source.
Connect power cord to
the power connector
The switch does not have a power switch. It is powered on
when the AC power adapter is connected to the switch and
to a power source.
Use only the AC power adapter and power cord
(if applicable), supplied with the switch. Use of other
adapters or power cords, including those that came with
other ProCurve Networking products, may result in
damage to the equipment.
Installing the Switch
Installation Procedures
Check the LEDs on the switch. The LED behavior is described
Port LEDs
Power LED
When the switch is powered on, it performs its diagnostic self
test. The self test takes approximately 8 seconds to complete.
Self Test LED Behavior:
During the self test:
The LEDs will go on for a couple of seconds during the phases
of the self test.
When the self test completes successfully:
The Power LED stays on.
In the default state, the FDx LED stays on and the Spd LED
stays off.
The port LEDs on the front of the switch go into their normal
operational mode.
– If the ports are connected to active network devices the
Link LEDs should be on.
If the LED display is different than what is described above, the
self test has not completed correctly. Refer to chapter 4,
“Troubleshooting” for diagnostic help.
Installing the Switch
Installation Procedures
3. Mount the Switch
After you have verified that the switch passes its self test, you are
ready to mount the switch in a stable location. The switch can be
mounted on a horizontal surface.
Horizontal Surface Mounting
Place the switch on a table or other horizontal surface. The switch
comes with rubber feet in the accessory kit that can be used to help
keep the switch from sliding on the surface.
Attach the rubber feet to the four corners on the bottom of the switch
within the embossed angled lines. Use a sturdy surface in an uncluttered area. You may want to secure the networking cables and switch
power cord to the table leg or other part of the surface structure to
help prevent tripping over the cords.
Make sure the air flow is not restricted around the sides of
the switch.
4. Connect the Switch to a Power Source
Plug the included AC power adapter into the switch’s power
connector and into a nearby AC power source. If the power
adapter part number 5188-6700 is used; first plug the country
specific power cord into the adapter, and then into the AC power
Re-check the LEDs during self test. See “Self Test LED Behavior:”
on page 2-7.
Installing the Switch
Installation Procedures
5. Connect the Network Cables
Using the RJ-45 Connectors (10/100/1000Base-T ports)
To connect:
Push the RJ-45 plug into the
RJ-45 jack until the tab on
the plug clicks into place.
When power is on for the
switch and for the connected
device, the Link/Act LED for
the port should light to
confirm a powered-on
device (for example, an end
node) is at the other end of
the cable.
If the Link LED does not go
on when the network cable is
connected to the port, see
“Diagnosing With the LEDs”
in chapter 4,
RJ-45 connector
100-ohm unshielded or shielded twistedpair cable:
• Category 3, 4, or 5 for 10 Mbps ports
• Category 5 only for 100 Mbps ports
• Category 5, 5e, or 6 for 1000 Mbps ports
Maximum distance: 100 meters
To disconnect:
Press the small tab on the plug and pull the plug out of the jack.
Configuring the Switch
Initial Configuration
The ProCurve Switch 1700-8 can be managed through a Web-browser
interface that you can access from any PC or workstation in the
connected network. For initial configuration, you may want to assign
an IP address to the switch that is compatible with your existing
network. However, you first need to access the Web interface using
the switch’s default IP address.
The following procedure shows how to access the Web interface and
change the switch’s IP address:
Place the switch close to the PC that you will use for
configuration. It helps if you can see the front panel of the switch
while working on your PC.
Connect the Ethernet port of your PC to any port on the front
panel of your switch, start your PC (if it is not already running),
connect power to the switch and when your PC has finished its
start-up sequence, verify that you have a link by checking the
LEDs on the front-panel of the switch (see “LEDs” on page 1-2 for
more information).
Set your PC’s IP address to be on the same subnet as the switch.
The default IP address of the switch is and the subnet
mask is, so the PC and switch are on the same
subnet when they both have addresses that start 192.168.2.x. If
the PC and switch are already on the same subnet, proceed
directly to step 4. Otherwise, you must manually set the PC’s IP
Configuring the Switch
Changing PC’s IP Address
address to 192.168.2.x (where "x" can be any number from 1 to
255, except 10). If you are unfamiliar with this process, see
“Changing PC’s IP Address” on page 3-2.
Open your Web browser and enter the address
If your PC is properly configured, you will see the login page of
your switch. If you do not see the login page, check your settings
and repeat step 3.
There is no default password, just click the Login button to access
the Web management interface.
From the menu, click SYSTEM, then IP Address. On the IP Address
page, enter the IP address, Subnet Mask and Gateway IP Address
for the switch, then click on the APPLY button.
No other configuration changes are required at this stage, but it is
recommended that you configure an administrator password before
logging out. From the menu, click SYSTEM, then Password. On the
Password page, fill in all the fields before clicking on the APPLY
If you cannot remember the switch's IP address or
password, you can restore the factory default settings by
following the procedure described in the
"Troubleshooting" section.
Changing PC’s IP Address
To change the IP address of your PC:
On Windows® XP, go to Start, Settings, Network and Dial-up
Right-click the connection icon of which the IP address you want
to change, and then click properties.
Configuring the Switch
Where to Go From Here
In General tab, under Components checked are used by this connection,
click to select Internet Protocol (TCP/IP), and then click Properties to
open Internet Protocol (TCP/IP) Properties dialog box.
In Internet Protocol (TCP/IP) Properties dialog box, click to select Use
the following IP address.
In IP address, Subnet mask, and Default gateway, type your intended
Click OK to save the changes and quit.
Where to Go From Here
For more information on the Web browser interface and all the
features that can be configured on the ProCurve Switch 1700-8, see
the ProCurve Series 1700 Switch Management and Configuration
Guide, which is available on the ProCurve Networking Web site,
This section describes how to troubleshoot the switch. For more
information, see the chapter “Troubleshooting” in the ProCurve
Series 1700 Switch Management and Configuration Guide, which
is available on the ProCurve Networking Web site,
This chapter describes the following:
basic troubleshooting tips (page 4-1)
diagnosing with the LEDs (page 4-2)
forgotten the IP address or password (page 4-4)
hardware diagnostic tests (page 4-4)
HP Customer Support Services (page 4-5)
Basic Troubleshooting Tips
Common problems and their solutions are listed in the following
For more information on possible network problems and their
solutions, refer to the technical note “Troubleshooting LAN
Performance and Intermittent Connectivity Problems”, which can be
found on the ProCurve Networking Web site,,
in the Information Library section.
Diagnosing With the LEDs
Switch fails Power On
Self Test (POST)
Troubleshoot using the LEDs. See “Diagnosing With
the LEDs” on page 4-2
Link light does not light
when a cable is
Look for loose or obviously faulty connections. If
they appear to be OK, make sure the connections
are snug. If that does not correct the problem, try a
different cable.
Diagnosing With the LEDs
LED patterns on the switch may indicate a problem condition.
Check in the table for the LED pattern that you see on your
Refer to the corresponding diagnostic tip on the next few pages.
LED Pattern Indicating Problems
Port Link
Diagnostic Tips
Off with power adapter
plugged in
Off with cable connected
* This LED is not important for the diagnosis.
Diagnosing With the LEDs
Diagnostic Tips:
The switch’s
power adapter
is not plugged
into an active
AC power
source, or the
power adapter
may have failed.
1. Verify the AC power adapter is plugged into an
active power source and to the switch. Make
sure these connections are snug.
2. Try power cycling the switch by unplugging
and plugging in the power.
3. If the Power LED is still not on, verify that the
AC power source works by plugging another
device into the outlet. Or try plugging the
switch into a different outlet.
If this condition persists, the switch’s power
adapter may have failed. Call your ProCurve
Networking authorized network reseller, or use
the electronic support services from ProCurve
Networking to get assistance. See the Customer
Support/Warranty booklet for more information.
The network
connection is
not working
Try the following procedures:
• For the indicated port, verify that both ends of
the cabling, at the switch and the connected
device, are secure.
• Verify the connected device and switch are
both powered on and operating correctly.
• Verify the connected devices comply with the
appropriate IEEE 802.3 standard, including
transmission of the Link signal.
• If the other procedures don’t resolve the problem, try using a different port or a different
Forgotten the IP Address or Password
Forgotten the IP Address or
If you have forgotten the switch’s IP address or administration
password you can return the switch to its factory default state by
doing the following:
Remove the power adapter from the back of the switch.
Remove all cables from the front-panel ports.
Connect port 1 to port 2 on the front panel using a standard
network cable.
Reconnect the power adapter to the rear of the switch.
Wait at least 40 seconds before disconnecting port 1 from port 2.
After completing this procedure, there will be no password, the IP
address will be returned to the default, and all
configuration settings will be returned to factory defaults.
Hardware Diagnostic Tests
Testing the Switch by Resetting It
If you believe that the switch is not operating correctly, you can reset
the switch to test its circuitry. To reset the switch, unplug and plug in
the power adapter (power cycling).
Power cycling causes the switch to perform its power-on self-test, and
almost always will resolve any temporary operational problems.
HP Customer Support Services
HP Customer Support Services
If you are still having trouble with your switch, ProCurve Networking
offers support 24 hours a day, seven days a week through the use of
a number of automated electronic services. See the Customer
Support/Warranty booklet that came with your switch for information
on how to use these services to get technical support. The ProCurve
Networking Web site, also provides up-todate support information.
Additionally, your ProCurve Networking authorized network reseller
can provide you with assistance, both with services that they offer
and with services offered by ProCurve Networking.
Before Calling Support
Before calling your networking dealer or HP Support, to make the
support process most efficient, you first should have retrieved the
following information:
Information Item
Information Location
• product identification
the front of the switch
• details about the switch’s status
including the software (OS) version, a copy of the switch configuration, a copy of the switch Event
Log, and a copy of the switch status and counters information
Web interface
• copy of your network topology
map, including network addresses
assigned to the relevant devices
your network records
19.6 cm (7.7 in)
11.6 cm (4.5 in)
4.4 cm (1.73 in)
Weight :
0.54 kg (1.19 lbs)
DC voltage:
12-13 volts
Maximum current:
1.0-0.8 A
0 °C to 40 °C (32 °F to 104 °F) -40 °C to 70 °C (-40 °F to 158 °F)
Relative humidity:
10 % to 90 % at 40 °C (104 °F) 10 % to 90 % at 65 °C (149 °F)
Maximum altitude:
3048 m (10,000 ft)
3048 m (10,000 ft)
The 10/100/1000 Mbps RJ-45 twisted-pair ports are compatible
with the following standards:
IEEE 802.3ab 1000Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3 10Base-T
The switch complies with these safety standards:
EN60950-1 / IEC 60950-1
CSA 22.2 No. 60950-1
UL 60950-1
Safety and EMC Regulatory
Safety Information
Documentation reference symbol. If the product is marked with
this symbol, refer to the product documentation to get more
information about the product.
A WARNING in the manual denotes a hazard that can cause
injury or death.
A CAUTION in the manual denotes a hazard that can damage
Do not proceed beyond a WARNING or CAUTION notice until
you have understood the hazardous conditions and have taken
appropriate steps.
These are safety class I products and have protective earthing
terminals. There must be an uninterruptible safety earth ground from
the main power source to the product’s input wiring terminals, power
cord, or supplied power cord set. Whenever it is likely that the
protection has been impaired, disconnect the power cord until the
ground has been restored.
Safety and EMC Regulatory Statements
Safety Information
For LAN cable grounding:
If your LAN covers an area served by more than one power
distribution system, be sure their safety grounds are securely
LAN cables may occasionally be subject to hazardous transient voltages (such as lightning or disturbances in the
electrical utilities power grid). Handle exposed metal components of the network with caution.
There are no user-serviceable parts inside these products. Any
servicing, adjustment, maintenance, or repair must be performed only
by service-trained personnel.
These products do not have a power switch; they are powered on
when the adapter’s power cord is plugged in.
Safety and EMC Regulatory Statements
Safety Information
Informations concernant la sécurité
Symbole de référence à la documentation. Si le produit est
marqué de ce symbole, reportez-vous à la documentation du
produit afin d'obtenir des informations plus détaillées.
Dans la documentation, un WARNING indique un danger
susceptible d'entraîner des dommages corporels ou la mort.
Un texte de mise en garde intitulé CAUTION indique un danger
susceptible de causer des dommages à l'équipement.
Ne continuez pas au-delà d'une rubrique WARNING ou
CAUTION avant d'avoir bien compris les conditions présentant
un danger et pris les mesures appropriées.
Cet appareil est un produit de classe I et possède une borne de mise
à la terre. La source d'alimentation principale doit être munie d'une
prise de terre de sécurité installée aux bornes du câblage d'entrée,
sur le cordon d'alimentation ou le cordon de raccordement fourni
avec le produit. Lorsque cette protection semble avoir été
endommagée, débrancher le cordon d'alimentation jusqu'à ce que la
mise à la terre ait été réparée.
Mise à la terre du câble de réseau local:
si votre réseau local s'étend sur une zone desservie par plus d'un
système de distribution de puissance, assurez-vous que les prises de
terre de sécurité soient convenablement interconnectées.
Les câbles de réseaux locaux peuvent occasionnellement être
soumis à des surtensions transitoires dangereuses (telles que la
foudre ou des perturbations dans le réseau d'alimentation public).
Manipulez les composants métalliques du réseau avec précautions.
Safety and EMC Regulatory Statements
Safety Information
Aucune pièce contenue à l'intérieur de ce produit ne peut être réparée
par l'utilisateur. Tout dépannage, réglage, entretien ou réparation
devra être confié exclusivement à un personnel qualifié.
Cet appareil ne comporte pas de commutateur principal ; la mise sous
tension est effectuée par branchement du cordon d'alimentation.
Safety and EMC Regulatory Statements
Safety Information
Hinweise zur Sicherheit
Symbol für Dokumentationsverweis. Wenn das Produkt mit
diesem Symbol markiert ist, schlagen Sie bitte in der Produktdokumentation nach, um mehr Informationen über das Produkt
zu erhalten.
Eine WARNING in der Dokumentation symbolisiert eine Gefahr,
die Verletzungen oder sogar Todesfälle verursachen kann.
CAUTION in der Dokumentation symbolisiert eine Gefahr, die dis
Gerät beschädigen kann.
Fahren Sie nach dem Hinweis WARNING oder CAUTION erst
fort, nachdem Sie den Gefahrenzustand verstanden und die
entsprechenden Maßnahmen ergriffen haben.
Dies ist ein Gerät der Sicherheitsklasse I und verfügt über einen
schützenden Erdungsterminal. Der Betrieb des Geräts erfordert eine
ununterbrochene Sicherheitserdung von der Hauptstromquelle zu
den Geräteingabeterminals, den Netzkabeln oder dem mit Strom
belieferten Netzkabelsatz voraus. Sobald Grund zur Annahme
besteht, daß der Schutz beeinträchtigt worden ist, das Netzkabel aus
der Wandsteckdose herausziehen, bis die Erdung wiederhergestellt
Für LAN-Kabelerdung:
Wenn Ihr LAN ein Gebiet umfaßt, das von mehr als einem Stromverteilungssystem beliefert wird, müssen Sie sich vergewissern, daß
die Sicherheitserdungen fest untereinander verbunden sind.
LAN-Kabel können gelegentlich gefährlichen Übergangsspannungen ausgesetzt werden (beispielsweise durch Blitz oder Störungen
in dem Starkstromnetz des Elektrizitätswerks). Bei der
Handhabung exponierter Metallbestandteile des Netzwerkes Vorsicht walten lassen.
Safety and EMC Regulatory Statements
Safety Information
Dieses Gerät enthält innen keine durch den Benutzer zu wartenden
Teile. Wartungs-, Anpassungs-, Instandhaltungs- oder
Reparaturarbeiten dürfen nur von geschultem Bedienungspersonal
durchgeführt werden.
Dieses Gerät hat keinen Netzschalter; es wird beim Anschließen des
Netzkabels eingeschaltet.
Safety and EMC Regulatory Statements
Safety Information
Considerazioni sulla sicurezza
Simbolo di riferimento alla documentazione. Se il prodotto è
contrassegnato da questo simbolo, fare riferimento alla documentazione sul prodotto per ulteriori informazioni su di esso.
La dicitura WARNING denota un pericolo che può causare
lesioni o morte.
La dicitura CAUTION denota un pericolo che può danneggiare
le attrezzature.
Non procedere oltre un avviso di WARNING o di CAUTION prima
di aver compreso le condizioni di rischio e aver provveduto alle
misure del caso.
Questo prodotto è omologato nella classe di sicurezza I ed ha un
terminale protettivo di collegamento a terra. Dev'essere installato un
collegamento a terra di sicurezza, non interrompibile che vada dalla
fonte d'alimentazione principale ai terminali d'entrata, al cavo
d'alimentazione oppure al set cavo d'alimentazione fornito con il
prodotto. Ogniqualvolta vi sia probabilità di danneggiamento della
protezione, disinserite il cavo d'alimentazione fino a quando il
collegaento a terra non sia stato ripristinato.
Per la messa a terra dei cavi LAN:
se la vostra LAN copre un'area servita da più di un sistema di
distribuzione elettrica, accertatevi che i collegamenti a terra di
sicurezza siano ben collegati fra loro;
i cavi LAN possono occasionalmente andare soggetti a pericolose
tensioni transitorie (ad esempio, provocate da lampi o disturbi nella
griglia d'alimentazione della società elettrica); siate cauti nel
toccare parti esposte in metallo della rete.
Safety and EMC Regulatory Statements
Safety Information
Nessun componente di questo prodotto può essere riparato
dall'utente. Qualsiasi lavoro di riparazione, messa a punto,
manutenzione o assistenza va effettuato esclusivamente da personale
Questo apparato non possiede un commutatore principale; si mette
scotto tensione all'inserirsi il cavo d'alimentazione.
Safety and EMC Regulatory Statements
Safety Information
Consideraciones sobre seguridad
Símbolo de referencia a la documentación. Si el producto va
marcado con este símbolo, consultar la documentación del
producto a fin de obtener mayor información sobre el producto.
Una WARNING en la documentación señala un riesgo que
podría resultar en lesiones o la muerte.
Una CAUTION en la documentación señala un riesgo que podría
resultar en averías al equipo.
No proseguir después de un símbolo de WARNING o CAUTION
hasta no haber entendido las condiciones peligrosas y haber
tomado las medidas apropiadas.
Este aparato se enmarca dentro de la clase I de seguridad y se
encuentra protegido por una borna de puesta a tierra. Es preciso que
exista una puesta a tierra continua desde la toma de alimentación
eléctrica hasta las bornas de los cables de entrada del aparato, el cable
de alimentación o el juego de cable de alimentación suministrado. Si
existe la probabilidad de que la protección a tierra haya sufrido
desperfectos, desenchufar el cable de alimentación hasta haberse
subsanado el problema.
Puesta a tierra del cable de la red local (LAN):
Si la LAN abarca un área cuyo suministro eléctrico proviene de más
de una red de distribución de electricidad, cerciorarse de que las
puestas a tierra estén conectadas entre sí de modo seguro.
Es posible que los cables de la LAN se vean sometidos de vez en
cuando a voltajes momentáneos que entrañen peligro (rayos o
alteraciones en la red de energía eléctrica). Manejar con precaución
los componentes de metal de la LAN que estén al descubierto.
Safety and EMC Regulatory Statements
Safety Information
Este aparato no contiene pieza alguna susceptible de reparación por
parte del usuario. Todas las reparaciones, ajustes o servicio de
mantenimiento debe realizarlos solamente el técnico.
Este producto no tiene interruptor de potencia; se activa cuando se
enchufa el cable de alimentación.
Safety and EMC Regulatory Statements
Safety Information
Safety Information (Japan)
Safety and EMC Regulatory Statements
Safety Information
Safety Information (China)
Safety and EMC Regulatory Statements
EMC Regulatory Statements
EMC Regulatory Statements
FCC Class A
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void your
authority to operate the equipment.
This product complies with Class A Canadian EMC requirements.
Australia/New Zealand
This product complies with Australia/New Zealand EMC
Class A requirements.
Safety and EMC Regulatory Statements
EMC Regulatory Statements
VCCI Class A
Safety and EMC Regulatory Statements
EMC Regulatory Statements
European Community
according to ISO/IEC Guide 22 and EN45014
Manufacturer's Name:
Hewlett-Packard Company
Manufacturer's Address:
8000 Foothills Blvd
Roseville, CA 95747-5502
declares that the product:
Product Name:
ProCurve Switch 1800-8G, 1700-8, and 1400-8G
Model Number:
J9029A, J9079A, and J9077A
Accessories: N/A
Regulatory Model Number: RSVLC-0510A
conforms to the following Product Specifications:
EN 60950-1:2001
IEC 60950-1:2001
EN 55022:1998 +A1:2000+A2:2003 / CISPR-22:1997 Class A +A1:2000 +A2:2002
EN 55024: 1998) +A1:2001 +A2:2003
EN 61000-3-2:2000 - Harmonics
EN 61000-3-3:1995 +A1:2001 - Flicker
Supplementary Information:
The product herewith complies with the requirements of the Low Voltage Directive 73/23/EEC
and the EMC Directive 89/336/EEC and carries the CE marking accordingly.
Tested with Hewlett-Packard Co. products only.
Roseville, 08-December-2006
Michael E. Avery,
Regulatory Engineering Manager
European Contact: Your local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Department TRE,
Herrenberger Strasse 140, D-71034 Böblingen (FAX:+49-7031-14-3143).
Safety and EMC Regulatory Statements
EMC Regulatory Statements
Regulatory Information (China)
䗖⫼Ѣ᠔᳝ProCurve Networking by HP ѻક
Recycle Statements
Waste Electrical and Electronic
Equipment (WEEE) Statements
Disposal of Waste Equipment by Users in Private Household
in the European Union
This symbol on the product or on its packaging indicates that
this product must not be disposed of with your other household
waste. Instead, it is your responsibility to dispose of your waste
equipment by handing it over to a designated collection point
for the recycling of waste electrical and electronic equipment.
The separate collection and recycling of your waste equipment
at the time of disposal will help to conserve natural resources
and ensure that it is recycled in a manner that protects human
health and the environment. For more information about where
you can drop off your waste equipment for recycling, please
contact your local city office, your household waste disposal
service or the shop where you purchased the product.
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements
Likvidace zařízení soukromými domácími uživateli
v Evropské unii
Tento symbol na produktu nebo balení označuje výrobek,
který nesmí být vyhozen spolu s ostatním domácím
odpadem. Povinností uživatele je předat takto označený
odpad na předem určené sběrné místo pro recyklaci
elektrických a elektronických zařízení. Okamžité třídění a
recyklace odpadu pomůže uchovat přírodní prostředí
a zajistí takový způsob recyklace, který ochrání zdraví a
životní prostředí člověka. Další informace o možnostech
odevzdání odpadu k recyklaci získáte na příslušném
obecním nebo městském úřadě, od firmy zabývající se
sběrem a svozem odpadu nebo v obchodě, kde jste produkt
Bortskaffelse af affald fra husstande i den Europæiske Union
Hvis produktet eller dets emballage er forsynet med dette
symbol, angiver det, at produktet ikke må bortskaffes med andet
almindeligt husholdningsaffald. I stedet er det dit ansvar at
bortskaffe kasseret udstyr ved at aflevere det på den kommunale genbrugsstation, der forestår genvinding af kasseret elektrisk og elektronisk udstyr. Den centrale modtagelse og
genvinding af kasseret udstyr i forbindelse med bortskaffelsen
bidrager til bevarelse af naturlige ressourcer og sikrer, at
udstyret genvindes på en måde, der beskytter både mennesker
og miljø. Yderligere oplysninger om, hvor du kan aflevere
kasseret udstyr til genvinding, kan du få hos kommunen, den
lokale genbrugsstation eller i den butik, hvor du købte
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements
Seadmete jäätmete kõrvaldamine eramajapidamistes
Euroopa Liidus
See tootel või selle pakendil olev sümbol näitab, et kõnealust
toodet ei tohi koos teiste majapidamisjäätmetega kõrvaldada.
Teie kohus on oma seadmete jäätmed kõrvaldada, viies need
elektri- ja elektroonikaseadmete jäätmete ringlussevõtmiseks
selleks ettenähtud kogumispunkti. Seadmete jäätmete eraldi
kogumine ja ringlussevõtmine kõrvaldamise ajal aitab kaitsta
loodusvarasid ning tagada, et ringlussevõtmine toimub viisil,
mis kaitseb inimeste tervist ning keskkonda. Lisateabe
saamiseks selle kohta, kuhu oma seadmete jäätmed ringlussevõtmiseks viia, võtke palun ühendust oma kohaliku linnakantselei, majapidamisjäätmete kõrvaldamise teenistuse või
kauplusega, kust Te toote ostsite.
Laitteiden hävittäminen kotitalouksissa Euroopan unionin
Jos tuotteessa tai sen pakkauksessa on tämä merkki, tuotetta
ei saa hävittää kotitalousjätteiden mukana. Tällöin hävitettävä
laite on toimitettava sähkölaitteiden ja elektronisten laitteiden
kierrätyspisteeseen. Hävitettävien laitteiden erillinen käsittely
ja kierrätys auttavat säästämään luonnonvaroja ja
varmistamaan, että laite kierrätetään tavalla, joka estää terveyshaitat ja suojelee luontoa. Lisätietoja paikoista, joihin
hävitettävät laitteet voi toimittaa kierrätettäväksi, saa ottamalla
yhteyttä jätehuoltoon tai liikkeeseen, josta tuote on ostettu.
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements
Élimination des appareils mis au rebut par les ménages dans
l'Union européenne
Le symbole apposé sur ce produit ou sur son emballage indique
que ce produit ne doit pas être jeté avec les déchets ménagers
ordinaires. Il est de votre responsabilité de mettre au rebut vos
appareils en les déposant dans les centres de collecte publique
désignés pour le recyclage des équipements électriques et
électroniques. La collecte et le recyclage de vos appareils mis
au rebut indépendamment du reste des déchets contribue à la
préservation des ressources naturelles et garantit que ces
appareils seront recyclés dans le respect de la santé humaine
et de l'environnement. Pour obtenir plus d'informations sur les
centres de collecte et de recyclage des appareils mis au rebut,
veuillez contacter les autorités locales de votre région, les
services de collecte des ordures ménagères ou le magasin
dans lequel vous avez acheté ce produit.
Entsorgung von Altgeräten aus privaten Haushalten in der EU
Das Symbol auf dem Produkt oder seiner Verpackung weist
darauf hin, dass das Produkt nicht über den normalen Hausmüll
entsorgt werden darf. Benutzer sind verpflichtet, die Altgeräte
an einer Rücknahmestelle für Elektro- und Elektronik-Altgeräte
abzugeben. Die getrennte Sammlung und ordnungsgemäße
Entsorgung Ihrer Altgeräte trägt zur Erhaltung der natürlichen
Ressourcen bei und garantiert eine Wiederverwertung, die die
Gesundheit des Menschen und die Umwelt schützt. Informationen dazu, wo Sie Rücknahmestellen für Ihre Altgeräte finden,
erhalten Sie bei Ihrer Stadtverwaltung, den örtlichen Müllentsorgungsbetrieben oder im Geschäft, in dem Sie das Gerät
erworben haben
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements
Απόρριψη άχρηστου εξοπλισμού από χρήστες σε ιδιωτικά
νοικοκυριά στην Ευρωπαϊκή Ένωση
Το σύμβολο αυτό στο προϊόν ή τη συσκευασία του υποδεικνύει
ότι το συγκεκριμένο προϊόν δεν πρέπει να διατίθεται μαζί με τα
άλλα οικιακά σας απορρίμματα. Αντίθετα, είναι δική σας ευθύνη
να απορρίψετε τον άχρηστο εξοπλισμό σας παραδίδοντάς τον
σε καθορισμένο σημείο συλλογής για την ανακύκλωση
άχρηστου ηλεκτρικού και ηλεκτρονικού εξοπλισμού.
Η ξεχωριστή συλλογή και ανακύκλωση του άχρηστου
εξοπλισμού σας κατά την απόρριψη θα συμβάλει στη
διατήρηση των φυσικών πόρων και θα διασφαλίσει ότι
η ανακύκλωση γίνεται με τρόπο που προστατεύει την
ανθρώπινη υγεία και το περιβάλλον. Για περισσότερες
πληροφορίες σχετικά με το πού μπορείτε να παραδώσετε τον
άχρηστο εξοπλισμό σας για ανακύκλωση, επικοινωνήστε με το
αρμόδιο τοπικό γραφείο, την τοπική υπηρεσία διάθεσης
οικιακών απορριμμάτων ή το κατάστημα όπου αγοράσατε το
Készülékek magánháztartásban történő selejtezése az Európai
Unió területén
A készüléken, illetve a készülék csomagolásán látható azonos
szimbólum annak jelzésére szolgál, hogy a készülék a
selejtezés során az egyéb háztartási hulladéktól eltérő módon
kezelendő. A vásárló a hulladékká vált készüléket köteles a
kijelölt gyűjtőhelyre szállítani az elektromos és elektronikai
készülékek újrahasznosítása céljából. A hulladékká vált
készülékek selejtezéskori begyűjtése és újrahasznosítása
hozzájárul a természeti erőforrások megőrzéséhez, valamint
biztosítja a selejtezett termékek környezetre és emberi
egészségre nézve biztonságos feldolgozását. A begyűjtés
pontos helyéről bővebb tájékoztatást a lakhelye szerint
illetékes önkormányzattól, az illetékes szemételtakarító
vállalattól, illetve a terméket elárusító helyen kaphat.
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements
Smaltimento delle apparecchiature da parte di privati nel
territorio dell'Unione Europea
Questo simbolo presente sul prodotto o sulla sua confezione
indica che il prodotto non può essere smaltito insieme ai rifiuti
domestici. È responsabilità dell'utente smaltire le apparecchiature consegnandole presso un punto di raccolta designato al
riciclo e allo smaltimento di apparecchiature elettriche ed
elettroniche. La raccolta differenziata e il corretto riciclo delle
apparecchiature da smaltire permette di proteggere la salute
degli individui e l'ecosistema. Per ulteriori informazioni relative
ai punti di raccolta delle apparecchiature, contattare l'ente
locale per lo smaltimento dei rifiuti, oppure il negozio presso il
quale è stato acquistato il prodotto.
Nolietotu iekārtu iznīcināšanas noteikumi lietotājiem Eiropas
Savienības privātajās mājsaimniecībās
Šāds simbols uz izstrādājuma vai uz tā iesaiņojuma norāda, ka
šo izstrādājumu nedrīkst izmest kopā ar citiem sadzīves
atkritumiem. Jūs atbildat par to, lai nolietotās iekārtas tiktu
nodotas speciāli iekārtotos punktos, kas paredzēti izmantoto
elektrisko un elektronisko iekārtu savākšanai otrreizējai
pārstrādei. Atsevišķa nolietoto iekārtu savākšana un otrreizējā
pārstrāde palīdzēs saglabāt dabas resursus un garantēs, ka šīs
iekārtas tiks otrreizēji pārstrādātas tādā veidā, lai pasargātu vidi
un cilvēku veselību. Lai uzzinātu, kur nolietotās iekārtas var
izmest otrreizējai pārstrādei, jāvēršas savas dzīves vietas
pašvaldībā, sadzīves atkritumu savākšanas dienestā vai
veikalā, kurā izstrādājums tika nopirkts.
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements
Vartotojų iš privačių namų ūkių įrangos atliekų šalinimas
Europos Sąjungoje
Šis simbolis ant gaminio arba jo pakuotės rodo, kad šio
gaminio šalinti kartu su kitomis namų ūkio atliekomis negalima.
Šalintinas įrangos atliekas privalote pristatyti į specialią
surinkimo vietą elektros ir elektroninės įrangos atliekoms
perdirbti. Atskirai surenkamos ir perdirbamos šalintinos įrangos
atliekos padės saugoti gamtinius išteklius ir užtikrinti, kad jos
bus perdirbtos tokiu būdu, kuris nekenkia žmonių sveikatai ir
aplinkai. Jeigu norite sužinoti daugiau apie tai, kur galima
pristatyti perdirbtinas įrangos atliekas, kreipkitės į savo
seniūniją, namų ūkio atliekų šalinimo tarnybą arba parduotuvę,
kurioje įsigijote gaminį.
Verwijdering van afgedankte apparatuur door privégebruikers in de Europese Unie
Dit symbool op het product of de verpakking geeft aan dat dit
product niet mag worden gedeponeerd bij het normale
huishoudelijke afval. U bent zelf verantwoordelijk voor het
inleveren van uw afgedankte apparatuur bij een inzamelingspunt voor het recyclen van oude elektrische en elektronische
apparatuur. Door uw oude apparatuur apart aan te bieden en
te recyclen, kunnen natuurlijke bronnen worden behouden en
kan het materiaal worden hergebruikt op een manier waarmee
de volksgezondheid en het milieu worden beschermd. Neem
contact op met uw gemeente, het afvalinzamelingsbedrijf of de
winkel waar u het product hebt gekocht voor meer informatie
over inzamelingspunten waar u oude apparatuur kunt
aanbieden voor recycling.
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements
Pozbywanie się zużytego sprzętu przez użytkowników w
prywatnych gospodarstwach domowych w Unii Europejskiej
Ten symbol na produkcie lub jego opakowaniu oznacza, że
produktu nie wolno wyrzucać do zwykłych pojemników na
śmieci. Obowiązkiem użytkownika jest przekazanie zużytego
sprzętu do wyznaczonego punktu zbiórki w celu recyklingu
odpadów powstałych ze sprzętu elektrycznego i
elektronicznego. Osobna zbiórka oraz recykling zużytego
sprzętu pomogą w ochronie zasobów naturalnych i zapewnią
ponowne wprowadzenie go do obiegu w sposób chroniący
zdrowie człowieka i środowisko. Aby uzyskać więcej informacji
o tym, gdzie można przekazać zużyty sprzęt do recyklingu,
należy się skontaktować z urzędem miasta, zakładem
gospodarki odpadami lub sklepem, w którym zakupiono
Descarte de Lixo Elétrico na Comunidade Européia
Este símbolo encontrado no produto ou na embalagem indica
que o produto não deve ser descartado no lixo doméstico
comum. É responsabilidade do cliente descartar o material
usado (lixo elétrico), encaminhando-o para um ponto de coleta
para reciclagem. A coleta e a reciclagem seletivas desse tipo
de lixo ajudarão a conservar as reservas naturais; sendo assim,
a reciclagem será feita de uma forma segura, protegendo o
ambiente e a saúde das pessoas. Para obter mais informações
sobre locais que reciclam esse tipo de material, entre em
contato com o escritório da HP em sua cidade, com o serviço
de coleta de lixo ou com a loja em que o produto foi adquirido.
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements
Likvidácia vyradených zariadení v domácnostiach v Európskej
Symbol na výrobku alebo jeho balení oznacuje, že daný výrobok
sa nesmie likvidovat s domovým odpadom. Povinnostou
spotrebitela je odovzdat vyradené zariadenie v zbernom mieste,
ktoré je urcené na recykláciu vyradených elektrických a
elektronických zariadení. Separovaný zber a recyklácia
vyradených zariadení prispieva k ochrane prírodných zdrojov a
zabezpecuje, že recyklácia sa vykonáva spôsobom chrániacim
ludské zdravie a životné prostredie. Informácie o zberných
miestach na recykláciu vyradených zariadení vám poskytne
miestne zastupitelstvo, spolocnost zabezpecujúca odvoz
domového odpadu alebo obchod, v ktorom ste si výrobok
Odstranjevanje odslužene opreme uporabnikov v zasebnih
gospodinjstvih v Evropski uniji
Ta znak na izdelku ali njegovi embalaži pomeni, da izdelka ne
smete odvreči med gospodinjske odpadke. Nasprotno,
odsluženo opremo morate predati na zbirališče, pooblaščeno
za recikliranje odslužene električne in elektronske opreme.
Ločeno zbiranje in recikliranje odslužene opreme prispeva k
ohranjanju naravnih virov in zagotavlja recikliranje te opreme
na zdravju in okolju neškodljiv način. Za podrobnejše
informacije o tem, kam lahko odpeljete odsluženo opremo na
recikliranje, se obrnite na pristojni organ, komunalno službo ali
trgovino, kjer ste izdelek kupili.
Recycle Statements
Waste Electrical and Electronic Equipment (WEEE) Statements
Eliminación de residuos de equipos eléctricos y electrónicos
por parte de usuarios particulares en la Unión Europea
Este símbolo en el producto o en su envase indica que no debe
eliminarse junto con los desperdicios generales de la casa. Es
responsabilidad del usuario eliminar los residuos de este tipo
depositándolos en un "punto limpio" para el reciclado de
residuos eléctricos y electrónicos. La recogida y el reciclado
selectivos de los residuos de aparatos eléctricos en el
momento de su eliminación contribuirá a conservar los
recursos naturales y a garantizar el reciclado de estos residuos
de forma que se proteja el medio ambiente y la salud. Para
obtener más información sobre los puntos de recogida de
residuos eléctricos y electrónicos para reciclado, póngase en
contacto con su ayuntamiento, con el servicio de eliminación
de residuos domésticos o con el establecimiento en el que
adquirió el producto.
Bortskaffande av avfallsprodukter från användare i
privathushåll inom Europeiska Unionen
Om den här symbolen visas på produkten eller förpackningen
betyder det att produkten inte får slängas på samma ställe som
hushållssopor. I stället är det ditt ansvar att bortskaffa avfallet
genom att överlämna det till ett uppsamlingsställe avsett för
återvinning av avfall från elektriska och elektroniska produkter.
Separat insamling och återvinning av avfallet hjälper till att
spara på våra naturresurser och gör att avfallet återvinns på ett
sätt som skyddar människors hälsa och miljön. Kontakta ditt
lokala kommunkontor, din närmsta återvinningsstation för
hushållsavfall eller affären där du köpte produkten för att få mer
information om var du kan lämna ditt avfall för återvinning.
basic troubleshooting tips … 3-3, 4-1
included parts … 2-1
connecting the switch to a power
source … 2-8
on a horizontal surface … 2-8
precautions … 2-4
summary … 2-3
connecting cables to switch
ports … 2-9
connecting the switch to a power
source … 2-8
connector specifications … A-2
LEDs … 1-2
diagnostic tests … 4-4
testing the switch only … 4-4–4-5
electrical specifications,
switch … A-1
EMC regulatory statements … B-13
environmental specifications,
switch … A-1
behavior during self test … 2-7
descriptions of … 1-2
error indications … 4-2, 4-4
description … 1-2
Link/Act … 1-2
Power … 1-2
behavior during self test … 2-7
Link/Act LEDs … 1-2
mounting the switch
on a horizontal surface … 2-8
description … 1-2
network devices
connecting to the switch … 2-9
network ports
connecting to … 2-9
standards compliance … A-2
horizontal surface, mounting switch
on … 2-8
parts, included with the switch … 2-1
Index – 1
physical specifications, switch … A-1
port LEDs
FDx … 1-2
Link/Act … 1-2
10/100Base-TX, location on
switch … 1-1
network connections … 2-9
Power LED … 1-2
behavior during self test … 2-7
power source
connecting the switch to … 2-8
mounting the switch … 2-4
power requirements … 2-4
mounting precautions … 2-4
regulatory statements … B-13
resetting the switch
troubleshooting procedure … 4-4–
safety specifications … A-2
self test
LED behavior during … 2-7
connectors … A-2
electrical … A-1
environmental … A-1
physical … A-1
safety … A-2
summary of switch installation … 2-3
Index – 2
connecting to a power
source … 2-8
electrical specifications … A-1
specifications … A-1
included parts … 2-1
mounting on horizontal
surface … 2-8
physical specifications … A-1
switch operation
verifying after installation … 2-6
diagnostic tests … 4-4
switch operation … 4-4–4-5
tips for troubleshooting … 3-3, 4-1
basic tips … 3-3, 4-1
common network problems … 3-3,
diagnostic tests … 4-4
testing the switch … 4-4–4-5
Technical information in this document
is subject to change without notice.
© Copyright 2006, 2007 Hewlett-Packard
Development Company, L.P.
Reproduction, adaptation, or translation
without prior written permission is prohibited
except as allowed under the copyright laws.
Printed in China
March 2007
Manual Part Number
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF