Infocus Wall Mount for Thin Specification
Advertisement
Advertisement
Installation and Assembly: Flat Panel Wall Mount for
InFocus models INF4201, INF5501 and INF6501
C
Model:
SP-INF-WALLMNT
Maximum Load Capacity:
250 lb (113 kg)
US
This product is intended for use with UL
Listed products and must be installed
Features:
• Colors: Black
• Slim design holds screen close up against the wall
• Screen simply hooks onto the wall plate for quick and easy installation
• Optional horizontal adjustment of up to 12" (305 mm) (depending on screen model)
• Includes hardware for installation to wood studs, concrete and cinder block
• Theft-resistant security screws
ISSUED: 01-27-10 SHEET #: XXX-XXXX-1
NOTE: Read entire instruction sheet before you start installation and assembly.
WARNING
• Do not begin to install your InFocus product until you have read and understood the instructions and warnings contained in this Installation Sheet.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of an "edge to edge" stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding power.
• This product is intended for indoor use only. Use of this product outdoors could lead to product failure and personal injury.
• This product was designed to be installed on the following wall construction only;
WALL CONSTRUCTION
• Wood Stud
• Wood Beam
• Solid Concrete
• Cinder Block
• Metal Stud
• Brick
• Other or unsure?
HARDWARE REQUIRED
Included
Included
Included
Included
Do not attach except with approved metal stud accessory kit(not included)
Contact Qualified Professional (not evaluated by UL)
Contact Qualified Professional
Tools Needed for Assembly
• Stud finder ("edge to edge" stud finder is recommended)
• Phillips screwdriver
• Drill
• 5/16" (8 mm) bit for concrete and cinder block wall
• 5/32" (4 mm) bit for wood stud wall
• Carpenter's Level
Table of Contents
Parts List.................................................................................................................................................................................3
Installation to Triple Wood Stud Wall ......................................................................................................................................4
Installation to Solid Concrete or Cinder Block ........................................................................................................................5
Installing Adapter Brackets .....................................................................................................................................................6
Installing Flat Panel Screen to Wall Plate ...............................................................................................................................8
Visit the InFocus support site at www.infocus.com/support 2 of 8 ISSUED: 01-27-10 SHEET #: XXX-XXXX-1
Before you begin, make sure all parts shown are included with your product. Parts may appear slightly different than illustrated.
Parts List
AA wall plate
BB adapter bracket
CC
Description
#14 x 2.5" wood screw
DD
EE concrete anchor
4 mm allen wrench
Qty.
1
2
6
6
1
Part Number
200‐1901
200‐0942
5S1‐015‐C03
590‐0320
560‐1727
BB CC DD
AA
EE
Adapter Bracket Fasteners
M4 x 12 mm (4)
(504-9013)
M4 x 25 mm (4)
(504-1015)
M5 x 12 mm (4)
(520-1027)
M5 x 25 mm (4)
(520-9543)
M6 x 12 mm (4)
(520-1128)
M6 x 20 mm (4)
(520-9402)
M6 x 30 mm (4)
(510-9109)
.5" spacer (4)
(540-1057)
M6 x 25 mm (4)
(520-1208)
.75" spacer (4)
(540-1059)
M8 x 16 mm (6)
(520-9257)
Visit the InFocus support site at www.infocus.com/support 3 of 8
M8 x 40 mm (4)
(520-1136) multi-washer (4)
(580-1036)
M8 x 25 mm (4)
(520-1031)
ISSUED: 01-27-10 SHEET #: XXX-XXXX-1
Installation to Triple Wood Stud Wall
WARNING
• Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Installers are responsible to provide hardware for other types of mounting situations (not evaluated by UL).
1
Wall plate ( AA) can be mounted to three studs that are 16" (41 cm) apart. Use a stud finder to locate the edges of the studs. Use of an edge-to-edge stud finder is highly recommended. Based on their edges, draw a vertical line down each stud’s center. Place wall plate on wall as a template. The top mounting slots should be located
.75" above the desired screen center as shown in Figure 1.1. Level plate, and mark the center of the six mounting holes. Make sure that the mounting holes are on the stud centerlines. Drill six 5/32" (4 mm) dia. holes 2.5" (64 mm) deep. Make sure that the wall plate is level, secure it using six #14 x 2.5" wood screws ( CC) as shown in
Figure 1.2.
Skip to Step 2.
NOTE: Wall plate may be mounted up to 6" (152 mm) off center as shown in Figure 1.1.
STUD
AA
6"
(152 mm)
6"
(152 mm)
CS "X"
CS = center of screen
Figure. 1.1
"X" Distance .75" (19mm)
Visit the InFocus support site at www.infocus.com/support 4 of 8
AA
CC
Figure. 1.2
ISSUED: 01-27-10 SHEET #: XXX-XXXX-1
Installation to Solid Concrete or Cinder Block
WARNING
• When installing InFocus wall mounts on cinder block, verify that you have a minimum of 1-3/8" (35 mm) of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" (25 mm) minimum from the side of the block. Cinder block must meet ASTM
C-90 specifications. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware and components.
1
Make sure that wall plate ( AA) is level, use it as a template to mark six mounting holes. The top mounting slots should be located above the desired screen center as indicated by dimension X in Figure 1.1 on page 4.
Drill six 5/16" (8 mm) dia. holes to a minimum depth of
2.5" (64 mm). Insert anchors ( DD) in holes flush with wall as shown (right). Place wall plate over anchors and secure with #14 x 2.5" screws ( CC). Level, then tighten all fasteners.
WARNING
• Tighten screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Always attach concrete expansion anchors directly to load-bearing concrete.
• Never attach concrete expansion anchors to concrete covered with plaster, drywall, or other finishing material. If mounting to concrete surfaces covered with a finishing surface is unavoidable (not evaluated by UL), the finishing surface must be counterbored as shown below. Be sure concrete anchors do not pull away from concrete when tightening screws. If plaster/drywall is thicker than
5/8" (16 mm), custom fasteners must be supplied by installer (not evaluated by UL).
Drill holes and insert anchors ( DD).
2
AA concrete surface
DD
CC DD
Place plate ( AA) over anchors (DD) and secure with screws (CC).
Tighten all fasteners.
DD
AA
1
3
SOLID CONCreTe
CINDer BLOCk wall plate
INCORRECT concrete wall plate
CORRECT concrete
CC plaster/ dry wall plaster/ dry wall
Visit the InFocus support site at www.infocus.com/support 5 of 8 ISSUED: 01-27-10 SHEET #: XXX-XXXX-1
Installing Adapter Brackets
WARNING
• Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.
2
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen.
Place screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached. Place adapter brackets ( BB) on back of screen, align to holes, and center on back of screen as shown below. Attach the adapter brackets to the back of the screen using the appropriate combination of screws, multi-washers, and spacers as shown in Figure 2.1 or 2.2
NOTE: Top and bottom holes must always be used.
Verify that all holes are properly aligned, and then tighten screws using a Phillips screwdriver.
X
BB
CeNTer BrACkeTS VerTICALLy
ON BACk OF SCreeN
MULTI-WASHer
X
NOTE: "X" dimensions should be equal.
MeDIUM HOLe FOr M5 SCreWS
SMALL HOLe FOr M4 SCreWS
LArge HOLe FOr M6 SCreWS
Notes:
• The number of fasteners used will vary, depending upon the type of screen.
• Multi-washers and spacers may not be used, depending upon the type of screen.
• Use the corresponding hole in the multi- washer that matches your screw size as shown.
Visit the InFocus support site at www.infocus.com/support 6 of 8 ISSUED: 01-27-10 SHEET #: XXX-XXXX-1
2-1 Begin with the shortest length screw, hand thread through multi-washer and adapter bracket ( BB) into screen as shown below. Screw must make at least three full turns into the mounting hole and fit snug into place. Do not over tighten. If screw cannot make three full turns into the screen, select a longer length screw from the baffled fastener pack. repeat for remaining mounting holes, level brackets and tighten screws.
NOTE: Spacers may not be used, depending upon the type of screen.
SCreeN
Figure 2.1
MULTI-WASHer
SCREW
ADAPTer BrACkeT ( BB)
Visit the InFocus support site at www.infocus.com/support 7 of 8 ISSUED: 01-27-10 SHEET #: XXX-XXXX-1
Mounting and Removing Flat Panel Screen
WARNING
• Always use an assistant or mechanical lifting equipment to safely lift and position the flat panel screen.
3
Hook adapter brackets ( BB) onto wall plate (AA).
Then slowly swing screen in as shown. Turn safety/ security screws, using security allen wrench ( EE), clockwise at least six times to prevent screen from being removed as shown in Detail 1 of Figure 3.1.
Screen can be adjusted horizontally if desired as shown in Figure 3.2.
NOTE: To lock the screen down, tighten safety/ security screws to wall plate as shown in Detail 1.
To remove screen from mount, loosen safety/ security screws, swing screen away from mount, and lift screen off of mount.
CAUTION
• Do not tighten screws with excessive force.
Overtightening can cause damage to mount. Tighten screws to 40 in. • lb (4.5 N.M.) maximum torque.
AA
SAFeTy/
SeCUrITy
SCREWS
BB
Detail 1
BB
AA
Figure. 3.1
Visit the InFocus support site at www.infocus.com/support 8 of 8
Figure. 3.2
ISSUED: 01-27-10 SHEET #: XXX-XXXX-1

Public link updated
The public link to your chat has been updated.
Advertisement