null  null
CONTENTS
BEFORE USING THE UNIT
Before using the unit
Page 3
During the winter you should pay more attention
Page 3
Installation of KITURAMI unit
Page 4-5,11
Hydraulic connection of domestic water
Page 6
Connection of TURBO boiler to the heating network
Page 7
Connection of KS boiler to the heating network
Page 8
Equipment of the unit KITURAMI TURBO Plus
Page 9
Installation of the unit KITURAMI TURBO Plus
Page 10
Maintenance
Page 11
Electronic room thermostat 5500
Page 12
Operation of the room thermostat
Page 13
Settings of the room thermostat
Page 14
Code display on the screen, Trouble Localization and Solutions
Page 15-16
Temperature range of burner and circulator
Page 17
KRM co-firing wood and oil units
Page 17-18
Area thermostat CTR900
Page 18
Technical Specifications
Page 19
Founded in 1962,
KITURAMI, is the leading manufacturer in Korea and holds the first
place in sales of heating systems with oil and gas.
KITURAMI is recognized internationally for its products and is distinguished
for its contribution with the first awards for customer satisfaction, quality
control awards and prizes for research and technology.
Thank you for your choice. This manual will show you how to install the
KITURAMI unit and how to operate it. It will also show you what to do in case
of a sudden shutdown and how to use it safely.
Use heating oil rather than any other fuel.
In winter, even if you are away from home, do not disconnect the unit
from the mains.
DURING WINTER YOU SHOULD PAY MORE ATTENTION
Protect the unit from snow and rain. Make sure the
unit is in covered space for its best and safest
operation.
Do not leave the front of and
around the unit flammable
materials.
During the winter, when you are absent from your home for several hours or daysit is preferable to
activate the "OUTING" mode by the room thermostat. This function protects the heating system from
freezing, while the room will warm up faster when you switch to the "HEATING AREA" mode.
To protect from freezing and the water line is connected to the boiler, let the hot water tap slightly
open. During the summer remove the plug from the socket to protect the unit from flashes and
lightning.
Oil and Gas Oil Boilers
3
INSTALLATION OF KITURAMI UNIT
INSTALLATION OF KITURAMI UNIT
How to install the unit
1. Place the unit in a place with enough comfort - space for inspection and maintenance.
2. Put it on incombustible - non-combustible materials such as concrete - brick or cement, which can
withstand heavy weight.
3. Avoid placing it in a narrow enclosed space without ventilation or a bathroom with too much moisture. It
can be caused incomplete combustion due to lack of oxygen.
4. Do not place the unit in unprotected - open space.
5. Connect the plug of the unit to the mains using a socket exclusively for it.
safety valve 3 bar for steel boilers
2.5 bar for copper boilers
Main valves
Backflow valve
Expansion tank about 1 liter per 1000 calories of
the boiler
Chimney
Drain cock
Ventilation
The backflow valve is installed to prevent the natural flow of water to the radiators when we ask forl
domestic water during the summer months.
(The boiler TURBO Plus does not need backflow valve).
Unit
Material protecting
against moisture
Incorrect placement of valves
50mm
Fireproof base
Create a base 50mm above the floor to protect the unit against the moisture of the floor.
In order to avoid abnormal noise (caused by vibration), put four anti vibration rubbers on the four corners
of the base and place the unit on them. This process helps the long lifetime of the unit.
4
The valves should never be placed:
 between the boiler and the safety
valve
 between the boiler and the
expansion tank
In this case, if the burner will be activated
with closed valves, the boiler will be
destroyed.
5
HYDRAULIC CONNECTION OF DOMESTIC WATER
CONNECTION OF TURBO BOILER TO THE HEATING NETWORK
Water supplies
(applies to all models)
Supply to the heating system
Expansion tank
Green and yellow
wire connected to the
circulation pump
(phase - neutral). The
unit has its own
circulator hydrostat.
Cold domestic water inlet
Cold water supply from
water system
Safety valve
Filter to avoid mineral
deposits
Hot domestic water
outlet
Red and white wire
connected to the
thermostat. (Red to +
on the thermostat and
white to -).
Supply for hot water
consumption
Return from the
heating installation
(use the right or
left supply).
Before connecting the domestic water supply in the boiler measure the pressure of the water. Then
adjust the expansion water tank at the same bars and place a corresponding safety valve. E.g. we
assume the water supply is 4 bars. Then select a safety valve six bar and adjust the expansion tank at
4 bars.
The safety valve is placed at the outlet of hot domestic water. The magnet or polyphosphate filter
for salts are placed at the outlet of cold water to avoid mineral deposits.
6
7
EQUIPMENT OF THE KITURAMI TURBO PLUS UNIT
CONNECTION OF KS BOILER TO THE HEATING NETWORK
The KITURAMI TURBO PLUS unit is equipped with all the accessories of a boiler room.
In the unit TURBO PLUS are integrated the following components:
Supply to the heating system
• Circulator
• Expansion Tank
The KITURAMI unit includes in its equipment expansion tank for the heating network. However if
the system is large (mainly applies for TURBO PLUS 25 and 30 units), place an additional
expansion tank which you can connect anywhere in the facility.
Red and white wire
connected to the
thermostat. (Red to +
on the thermostat
and white to -).
Cold domestic water
inlet
• Safety Valve
Hot domestic water
outlet
• Filling valve of the heating network
If you do not place automatic filler, the user is able to control the manometer which shows the
pressure of the heating network and if water is needed to fill by the filling valve.
• Manometer
The two blue wires are
connected to the
circulation pump
(phase - neutral). The
unit has its own
circulator hydrostat.
• Three-way valve
The three-way valve directs water from the heating network to the installation when we ask for
heating or returns it to the boiler when we ask for domestic hot water. Due to the three-way valve it
is not needed to put in the installation a backflow valve as in the case of TURBO, GOLD and KS.
Return from the
heating installation
(use the right or left
supply).
Burner
• Magnetic filter of the installation
The magnetic filter removes the metal chips that are in the water of the heating network. Once per
year it is required to clean the magnetic filter.
• Automatic Ventilator
• Water Flow Sensor
8
9
INSTALLATION OF THE KITURAMI TURBO PLUS UNIT
INSTALLATION OF THE KITURAMI UNIT
Place the chimney 1m higher than its bend and use a T to its end.
Place screwing the automatic air vent located in the
package boiler
Automatic air vent
Cold domestic water
inlet
Red and white wire
connected to the
thermostat. (Red to +
on the thermostat and
white to -).
Hot domestic water
outlet
In this way is protected the unit from poor combustion
caused by the adverse wind.
If you cannot install a classic chimney, ask to be supplied
with the stainless steel chimney we provide for these
cases.
Insert the plug into an outlet that is also grounded.
To activate the first time the boiler, open the main switch ON-OFF of the
boiler, turn off the thermostat from the POWER button and press for 10 sec
button HOT WATER. Now you can choose any program you want from the
room thermostat.
MAINTENANCE
If you notice in the tank or the oil filter water or rubbish you should remove it
immediately.
Supply (diameter 1') to the heating
system
Supply (diameter 1 ¼’)
from the heating
installation (use the right
or left supply)
For cleaning the boiler, remove the lid of the smoke collector and with a brush
clean the boiler. Then remove the burner and collect the soot with a vacuum
cleaner. After that clean the orifice, the diffuser and the pins of the burner and
replace the boiler. Clean the oil pump filter.
Keep these distances as in figure
10
11
OPERATION OF THE ROOM THERMOSTAT
THERMOSTAT 5500
Room heating mode
Room Heating Mode
Sleeping mode
For heating the room successively press the button FUNCTION until it lights up the
room heating indication (sun).
Then adjust the temperature to the desired level using the arrow keys.
The indication with the temperature you select will flash on the display six times
and then the thermostat display will show the temperature at that time in the area
where the thermostat is located.
Temperature selection
Sleeping Mode
Antifreeze mode
Hot water mode
Pressing the button FUNCTION sequentially, select the sleep mode (moon). From
that moment the thermostat allows the room temperature to drop 3 degrees for 7
hours and then resets automatically in the heating room mode.
Setting button
Trouble indication
Antifreeze Mode
On - Off
Reset
Button fot hot water selection
Operation indication
We select it with the FUNCTION button when we want to be missing several hours
or days from home. When the room temperature drops below 8° C, it activates the
circulation pump when the water in the boiler drops below 8° C it activates the
burner. In this way we have absolute protection from frost and freezing in the boiler
and in the room where the thermostat is located.
Hot Water Mode
We select this mode with HOT WATER button. We use this function when we want
hot water during winter - summer. This operation lasts for 2.5 hours.
Button for mode selection
Room heating
Sleeping mode
Antifreeze
12
13
CODE DISPLAY ON THE SCREEN, TROUBLE
LOCALIZATION AND SOLUTIONS
SETTINGS OF THE ROOM THERMOSTAT
Correcting of the temperature on the room thermostat
If the temperature indicated by the thermostat is wrong, then to correct it we
press the FUNCTION button for 5 seconds. We decrease or increase the
temperature that is displayed on the screen until it reaches the desired level. To
reduce by one degree the room temperature, we reduce by two numbers the
thermostat indication. To increase by one degree the room temperature, we
increase by two numbers the thermostat indication.
If occurring any problem to the boiler, the screen of the room thermostat will display one of the
following codes:
01 √ The burner cannot ignite
• Check the engine burner if it works.
• The coil of the electromagnetic oil burner is burnt.
• There is no flow of oil from the tank to the burner.
• We don’ t have scintillation on the ignition rod of the burner.
• The coupling of the oil pump and motor is broken.
• When the photocell sees no flame in the combustion chamber, you should clean it.
Selection of the domestic water temperature
To select the water temperature we must have activated the HOT WATER
function. Then we press the button HOT WATER SETTING and with the arrows
we select the desired temperature from 41° C to 85° C. The display of the
thermostat displays the selected temperature for the hot domestic water, which as
lower it is the more difficult are concentrated salts in heat exchanger.
02
The photocell perceives light into the combustion chamber without any reason.
• Check if affected by sunlight or other strong light beam.
• Coley has created in the combustion chamber. You should clean it.
03
The burner turns on 5 times and then turns off
Selection of water temperature to heating units (radiators)
To select the water temperature in the heating units, we select the heating room mode
with the FUNCTION button and then press the HEATING WATER SETTING button.
The room thermostat displays the water temperature in the radiators and with the
arrows we can alter it per 5 degrees (from 50° C to 85° C).
Checking the water temperature in the boiler
• There is a poor oil flow to the burner.
• There the chimney is blocked.
• The boiler is filled with soot.
• There is a strong wind and hinders the exhaust gases outlet.
04
The temperature sensor cable (blue) is cut or does not have a good contact to the terminal
block.
05
The overheating sensor cable (blue) is cut or does not have a good contact to the terminal
block
To check the temperature of the water in the boiler press the button HEATING
WATER SETTING for 5 seconds.
14
15
OPERATING TEMPERATURE RANGE OF BURNER AND
CIRCULATOR
CODE DISPLAY ON THE SCREEN,
TROUBLE LOCALIZATION AND SOLUTIONS
CIRCULATOR
08
95
The cable connecting the the room thermostat to control of the boiler is damaged or the
thermostat is affected by instantaneous heavy frequency.
There is no water in the boiler
• Open the valve to pull up water.
• Check or insert automatic ventilation system on the boiler in order not to be held the air circuit.
• Check the sensor wires to make good contact.
Red cable right on the boiler.
Black wire bolted to the chassis of the unit above the control.
96
The water in the boiler is overheated. Press twice the room thermostat switch POWER. If the
same problem is reappeares, change the temperature sensor.
SELECTION OF WATER TEMPERATURE IN THE RADIATORS
50
ΟΝ
46
OFF
42
55
51
46
60
55
50
65
59
70
75
80
63
68
72
54
58
62
85
76
70
SELECTION OF WATER TEMPERATURE IN THE RADIATORS
ΟΝ
OFF
50
44
50
55
48
55
60
65
70
52
56
60
60
65
70
75
64
75
80
85
68
72
80
85
BURNER
KRM CO-FIRING WOOD AND OIL UNITS
98 À There is a shortage of oil in the tank.
00
The temperature sensor of the thermostat does not work.
Any time any damage occurs in the boiler – burner the trouble code is stored in the room
thermostat memory.
To see what damages are stored in the memory, we select the heating room mode and press the
button HOT WATER SETTING for five seconds. Then the screen of the room thermostat displays in
series the damages recorded. To delete the damages from the room thermostat memory, we close
the room thermostat from the POWER button and press the button HOT WATER for 10 seconds.
16
66
The KRM unit is equipped with two boilers and two combustion
chambers.
The oil boiler has a built-in oil burner.
We have the possibility from the control of the boiler to select the
function for the fuel we will use.
OIL: In this option the unit operates just like oil boilers. In wood
mode the unit’s operation is as follows: Firing the solid fuels
simultaneously is activated also the burner until the water
temperature of the boiler reaches 55°C. Then the burner will stop
and remains only the flame from the solid fuels. The water
temperature is then controlled by the automatic air damper of the
boiler.
17
TECHNICAL SPECIFICATIONS
If the room thermostat is not turned on then the burner will not start.
If the water temperature drops below 55° C due to lack of solid fuel then the burner will be activated
automatically and will keep the water temperature at 55 to 60° C approximately in the radiators.
Turbo
Dimensions
17 S
21 S
25S
30 S
KS 50
KS 70
Door dimensions
ATTENTION: For the boiler KRM we recommend open expansion tank.
The wood oil boiler is accompanied by a room thermostat CTR900 from which we select following
functions:
285X365
285X365
Φ80
Φ 80
Φ 80
Φ80
Φ125
Φ125
Φ200
Φ270
Heating
supplies Α
( inches )
1'' 1/4
1'' 1/4
1'' 1/4
1'' 1/4
1'' 1/2
1'' 1/2
1'' 1/4
2''
1/2''
1/2''
1/2''
1/2''
3/4''
3/4''
1/2''
3/4''
11,30
14,00
16,60
20,00
33,30
46,60
7,08
8,75
10,41
12,50
20,83
29,16
Hot water
supplies
( inches )
Hot water
supplies
lt/min with ∆Τ
25° C
Burner pump
operation
pressure
Injector
Performanc %
Performance with
wood (Cal)
Room heating mode
Sleeping mode
Hot water mode
Selection of room
temperature
18
10 bar
10 bar
10 bar
10 bar
10 bar
10 bar
10 bar
10 bar
0,50 60°Η
90,95%
0,60 60°H
91,50%
0,75 60°Η
91,20%
0,85 60°H
90,34%
1,65 60°H
89,50%
2,00 60°Η
88,72%
0,50 60°Η
89,90%
2,00 60°H
89,90%
14000-26000 30000 - 55000
Performance with
Oil (Cal)
Gold
Dimension
Antifreezing mode
KRM 70
1150X1070X1810
Chimney
Diameter Φ
(mm)
Hot water
supplies
lt/min with ∆Τ
40° C
Room temperature
indication
KRM 30
365X650X890 365Χ650Χ890 365X650X890 365Χ650Χ890 600X900X1200 600X900X1380 790X850X1395
to 17000
G17 S
G25 S
G30 S
G35 S
40 S
510X890X1050
50 S
325X600X810
325X600X810
360X650X890
360X650X890
510X890X110
Φ80
Φ80
Φ80
Φ80
Φ175
Φ125
1''
1''
1''
1'' 1/4
1'' 1/4
Door dimensions
Chimney
diameter Φ
(mm)
Heating
supplies Α
(inches)
1''
Hot water
Supplies
(inches)
1/2''
1/2''
1/2''
1/2''
1/2''
1/2''
11,30
16,60
20,00
23,30
26,60
33,30
7,08
10,41
12,50
14,50
16,60
20,83
10 bar
Operation indication
Hot water
supplies
lt/min with ∆Τ
25° C
Trouble indication
Hot water
supplies
lt/min with ∆Τ
40° C
Burner pump
operation
pressure
10 bar
10 bar
10 bar
10 bar
10 bar
Injector
0,50 60°Η
0,75 60°Η
0,85 60°Η
1,00 60°Η
1,25 60°Η
1,65 60°Η
Performance %
91,50%
91,25%
91,00%
90,20%
89,90%
90,00%
19
to 70000
HEATING - AIR CONDITIONING
INSTALLATION
AND OPERATION
MANUAL
for the boilers
• TURBO
• TURBO Plus
• GOLD
• KS
• KRM
HEATING - AIR CONDITIONING
Exclusive Representation
Collateral of Egnatia Road P.O. Box 1200 P.C. 57 008 Diavata Interchange, Thessaloniki
Tel.: 2310 574 920, 2310 574 803 • Fax.: 2310 574 893
e-mail: [email protected] • www.climacontrol.gr
Oil and Gas Oil Boilers
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement