DT-3260-24G Manual - English 0727 Wireless 2

Add to my manuals
17 Pages

advertisement

DT-3260-24G Manual - English 0727 Wireless 2 | Manualzz

UNIVERSAL GROUP CYCLING CONSOLE

SPEED : 0 ~ 99 KM/H

PULSE : 30 ~ 240 BPM

Time : Count down setting range 1~99 Minuets

Count up range 00:01~99:59

INSTRUCTION MANUAL

DT-3260 SPINNER BIKE CONSOLE SPECIFICATION

CADENCE BAR GRAPHIC: 0~199rpm per Bar

RPM : 0 ~ 199 RPM

IMPORTANT SAFETY INSTRUCTIONS WARNING

BEFORE BEGINNING THIS OR ANY OTHER

EXERCISE PROGRAM, CONSULT A PHYSICIAN.

THE PHYSICIAN CAN HELP YOU BETTER

DETERMINE WHAT ACTIVITIES OR PROGRAMS ARE

MOST SUITED FOR YOU. IF AT ANY TIME DURING

THE WORKOUT YOU FEEL FAINT, OR CHEST PAINS,

OR SEVER SHORTNESS OF BREATH, STOP

EXERCISING IMMEDIATLELY AND CONSULT A

PHYSICAN.

speed sensor transmitter before using.

The Universal Group Cycling Console assembly consists of a computer console, a magnet, one chest belt, and a speed sensor transmitter. The sensor in the transmitter counts the number of times the magnet

(mounted on the crank) passes the sensor. The speed sensor transmitter will then transmit a coded signal to the console, which contains the measured value (Speed and Cadence).

Both the computer console and the speed sensor transmitter use AAA type batteries. Please install the supplied AAA batteries in the computer console and

ITEM Check List

Sensor Cable & Holder Transmitter

Magnet

Velcro

AAA Batteries

Sponge

Cable Stripe

Clamp Bracket Set

(Model with Heart Rate Feature) except DT-3263M &

DT-3265W

Chest Belt or (DT-3260C Only)

Universal Group Cycling Console Battery

Installations:

1. Remove the battery cover from the back of the computer.

2. Insert 2 AAA batteries into the battery compartment and reinstall the battery cover.

3. When Battery working voltage is low, the ‘Low battery’ indicator will show up on the Console display.

INSTALLATION OF THE UNIVERSAL GROUP

CYCLING MONITOR

This UNIVERSAL GROUP CYCLING MONITOR can be installed onto most of Group Cycling and Spin Style bike handlebars.

Speed Sensor Transmitter Battery Installation

1. Remove the battery cover from the transmitter.

2. Install 2 AAA batteries in the battery compartment and reinstall the battery cover.

Console Installation:

1.Ensure the Console Clamp is securely mounted on the back of the console. Insert the mounting screw through the Console Clamp into the Console.

2. Spread the bottom of the console clamp apart, than clamp it back together over the top center of the handlebar. until it is securely attached to the handle bar.

Transmitter

Depending on the make and model of the bike, the

Speed Sensor Transmitter can typically be installed nearby the drive belt cover. The transmission range is around 2 meters from the Speed Sensor Transmitter to the Computer Console.

3.Turn the screw bar downward, slightly tighten the screw and adjust the console for optimal Visibility. Once the console is adjusted, continue to tighten the screw

Magnet

Firmly attach the magnet on the crank arm at the

measured location. The allowable maximum distance between the magnet and sensor end is 8 mm.

DISPLAY WINDOW

TIME

Time is the length of time (min. / sec.)

The time will count up or count down during user

peddling. When peddling stopped, the time will stop to count up or count down after 3 seconds.

CADENCE & SPEED

Cadence is the measurement of how fast the cranks are rotating in RPM’s. The approximate speed of the bike can also be display (MPH/KPH) in the section.

In addition to the MPH/KPH, the CADENCE will also display a bar graph that allows the rider to keep track of the approximate cadence that has been achieved.

Average Cadence or Speed will be automatically shown after the rider stop the pedaling for 3 seconds.

DISTANCE

Distance is the measurement of the approximate distance achieved on the bike. This distance is based on the user riding a bike with tires that are the same size as the bikes flywheel.

KCAL

Kcal is the approximation of calories burned during your work out. The calories are calculated by measuring the rider’s instantaneous heart rate, age, and weight.

HEART RATE (except DT-3263M & DT-3265M)

This is the approximation of heart rate detect from the chest belt during the work out. Average Heart Rate will be automatically shown after 3 seconds if the console cannot detect the current Heart Rate.

QUICK Start

In Power Saving Mode, Press any Key will bring the

CONSOLE to ‘QUICK Start’ active state.

Power Saving Mode QUICK START Mode

MODE SELECT

Press ‘MODE’ key to select the SPEED, DIST, TIME or

CLOCK display.

ALARM Setting (expect DT-3262M & DT-3263M)

Under the TIME MODE, Press ‘SET’ key to select the

Alarm display. The heart rate symbol will also flash to visually indicate that your heart rate is either above or below the selected target zone.

Resetting all measured value

To clear all the measured values, press and hold ‘SET’

key under the TIME Mode for 3 seconds. All the measured value for AVG SPEED, AVG PULSE, TIME,

DIST, KCAL will reset to zero.

TIMER Setting

The TIMER displays users’ exercise-workout time. If the user does not set the COUNT DOWN TIME, the TIME will count up from 00:00 to 99:59.

If user prior set the COUNT DOWN TIME, the TIME will count down to zero with flashing display and Alarm sound for 3 seconds. Then TIME will change automatically from counting down to counting up from

00:01. The user can go into TIMER setting from SPEED or DISTANCE Mode by press and hold ‘SET’ key for 3 seconds.

CLOCK Setting

Under the CLOCK MODE, Press and hold ‘SET’ key,

12H or 24H will flash. Press ‘SET’ key to switch from

12H to 24H. Press ‘MODE’ key to flash the CLOCK

HOUR, then Press ‘SET’ key to adjust the clock hour (0

– 24). Press ‘MODE’ key again to flash the CLOCK

MINUTE, the Press ‘SET’ key to adjust the clock minute

(0 – 59).

HEART RATE TARGET ZONES

Under SPEED or DISTANCE MODE, Hold ‘’SET’ key for

3 seconds to go into the setting, press ‘MODE’ key to go to the heart rate target zones window.

1.

Press the ‘SET’ key to select the gender, either:

Male / Female

Press the ‘SET’ key to increase maximum heart rate limit. After setting the maximum heart rate, press the

MODE key to adjust the minimum heart rate limit.

2.

Press the ‘MODE’ key to go to the weight unit setting. Press the ‘SET’ key to select the weight, either: Kg. / Lb. Note: this change of metric units to imperial units will affect the displaying units:

MPH/KPH, Lb/KG and ML/KM.

PERSONAL DATA SETTING

Accurate personal data will make your calories burned more accurate. Under SPEED or DISTANCE MODE,

Hold ‘’SET’ key for 3 seconds to go into the setting, continually press ‘MODE’ key to get to the personal data windows.

3.

Press the ‘MODE’ key, this will go to the weight setting. Press the ‘SET’ key to increase the weight by 0.5 Kg. or 0.5Lb.

HEART RATE PAIR STAGE (Exclusive in DT-3260C)

Note: All models will be paired right after produced

For commercial or maintenance reasons, the DT-3260C has the advantage of adapting to a confined space where there will be many chest belts without cross talk and interference. Hold ‘MODE’ key for 3 seconds, LCD will display ‘PULSE PAIR ‘ ( - - -) ‘ then bring the front center of the chest belt towards the embedded magnet on the top of the console for few gentle back and forth swipes as shown in the following images.

If the Heart Rate value is displayed on LCD, it means that the pair stage is successfully completed.

On the other hand, if the monitor displays ‘Err’, it means that the pair stage is failed. Then the user can press

‘SET’ key, and repeat the pair stage again. Alternatively, it will exit the pair stage automatically after 10 seconds with the memory of previous paired chest belt.

SPEED PAIR STAGE

(Exclusive in DT-3260C & DT-3261C)

Note: All models will be paired right after produced

For commercial and maintenance purpose – press and

Hold both ‘MODE’ and ‘’SET’ key for 3 seconds to go into the SPEED PAIR STAGE. The user will have to press the small ‘SPEED CONTROL PAIR KEY’ on the speed transmitter to actively sending signals to the console for pair stage. pair stage is successfully completed. On the other hand, if the monitor displays ‘Err’, it means that the pair stage is failed. Then the user can press ‘SET’ key, and repeat the pair stage again. Alternatively, it will exit the pair stage automatically after 10 seconds with the memory of previous paired speed transmitter.

SPEED transmitter illustration

Notice: The LED indication light will flash when pressed

SPEED ID CONTROL PAIR key and receiving signals.

If the number ‘0’ is displayed on LCD, it means that the

TROUBLESHOOTING

No Display on Console

1.

Press any key to bring the console to ‘Quick Start’ mode.

2.

Ensure that the batteries are installed properly in the Console and Transmitter. If they are, install fresh batteries.

No Heart Rate signal displayed

1.

Ensure that your chest strap is worn correctly, and that there is moisture under the electrodes of the chest strap.

2.

Relocate the bike away from any equipment that could potentially interrupt the radio frequency signal, such as a DVD player or television, etc.

RPM or HR does not change

1.

Press ‘MODE key’ repeatedly to toggle between

SPEED (SPD), DISTANCE (DIST), TIME (TIME) and CLOCK (CLK) values.

2.

Press and Hold ‘SET key’ repeatedly to clear past measured value or go into setting and exit.

Cadence number jumps high or low

1.

Separate bikes that may be paired to the same console code and are cross-talking, or simply run transmitter pair stage again on the bike.

2.

Relocate the bike to a different part of the room, away from any RF interference areas.

Heart Rate signal gets interrupted or drops out

1.

Ensure that there is a minimum distance of 36 inches between bikes.

2.

Verify that your chest strap is secure and that the electrodes are making contact with your chest at all times.

3.

Call our Customer Service department at 713-460-

8188 for assistance.

CAUTION

EXTERNAL INTERFERENCE MAY BE CAUSED BY

OTHER ELECTRONIC DEVISES, SUCH AS:

NEARBY TELEVISIONS, STEREO EQUIPMENT,

SPEAKERS, ELECTRICAL WIRE CABLING, ETC. IF

YOU EXPERIENCE DISTURBANCES IN THE

CONSOLE DISPLAY TRY MOVING YOUR BIKE (S)

AWAY FROM POTENTIAL RF INTERFERENCE

AREAS.

WARRANTY

This is to certify that the Universal Group Cycling

Monitor is warranted by Direction Technology to be free of all defects in materials and workmanship. This warranty does not apply to any defect caused by negligence, misuse, accident, alteration, improper maintenance, or an ‘act of God.’ The Universal Group

Cycling Monitor can be adapted to almost any indoor cycling or spinning bike. The Universal Group Cycling

Monitor carries a one-year warranty on the monitor, chest belt, and transmitter. Batteries are not warranted.

Contact our Customer Service Department to report any problems.

When calling, please be prepared to provide the customer service representative with the following information: Your name, the serial number of the inoperable monitor, and the date(s) of purchase. If warranty replacement parts are shipped, you may be

required to return the defective part. We reserve the right to make changes and improvements in our products without incurring any obligation to similarly alter products previously purchased. In order to maintain your product warranty and to ensure the safe and efficient operation of your monitor, only authorized

Direction Technology replacement parts can be used.

2.

3.

To clean the Universal Group Cycling Monitor system, lightly spray the monitor with an authorized cleaning / disinfectant solution and wipe dry with a soft towel. Use of any caustic cleaning solutions will void the warranty.

The Universal group Cycling Monitor system is

NOT waterproof, only water resistant. Any excessive exposure to water will void the warranty.

PLEASE NOTE:

1.

The Universal Group Cycling Monitor system are designed as sealed units and not meant to be opened other than for the sole purpose of installing batteries. Any opened units will void the warranty.

APPENDIX

Notice of FCC Compliance

This equipment has been tested and found to comply with the limits for a Class C Low Power Communication

Device Transmitter, pursuant to Part 15 of the FCC rules. Operation is subject to the following conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

There is no guarantee that interference will not occur in a particular installation. If this equipment experiences interference from a radio, television, or other RF signal, the user is encouraged to try and correct the interference by increasing the separation between the equipment and the apparatus emitting the interfering RF signal.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement