null  null
Thank you for your purchase of our product.
Before using the watch, read this instruction manual carefully to
ensure correct use.
After reading this manual, store it in a safe place for future
To check the movement number
A case number-4 alphanumeric characters Engraving position example
and 6 or more alphanumeric characters-is
engraved on the case back. (Figure on the
A combination of 2 numbers (4 digit and 6 or
more digit) is engraved on the case back of
your watch.
The engraving position may
differ depending on watch
In the example on the right, “1234” is the
movement number.
Safety precautions — IMPORTANT
This manual contains the following the instructions that should be strictly followed at all times to prevent injury to yourself and other persons as well as
damage to property.Understand the meaning of the following symbols and read
pages from 14 to 25.
★Safety advisories are categorized and depicted in this manual as follows:
Highly likely to cause death or serious injury
Can cause serious injury or death
Can or will cause minor or moderate injury or
★Important instructions are categorized and depicted in this manual as
Warning (caution) symbol followed by instructions that
should be followed or precautions that should be observed.
Warning (caution) symbol followed by prohibited matters.
<Protective stickers>
Be sure to remove any stickers covering the metal parts (back cover, band,
clasp) or glass of the watch before use. Otherwise, perspiration or moisture
may enter the gaps between the protective stickers and the parts, which
may result in a skin rash and/or corrosion of the metal parts.
<Band adjustment>
Do not adjust the length of the band (metal or rubber) yourself. If you fail to
perform the work properly, the watch may fall off, or an injury may occur
during adjustment. (If you purchase a product which is sold with a special
tool for band adjustment, you may carefully adjust the band yourself.)
For band adjustment, consult the shop where you purchased the watch or
your MB Service center. Other shops may not be able to handle the watch,
or may charge a fee.
Introduction..................................................................................... 1
Safety precautions......................................................................... 2
Before using.................................................................................... 6
435A (three hands, Plain models).......................... 8
G110 (three hands, with date)................................ 9
J519 (chronograph 30-minutes type).................. 10
Zero Positioning of Chronograph Hands................................... 12
Water Resistance......................................................................... 14
Precautionary Item and Usage Limitation.................................. 16
Warranty and service................................................................... 26
Repair & Warranty service........................................................... 30
Before using
★Before setting the time and calendar
•When the screw down crown is equipped on your model, loosen
the screw before operation. After operation, return the crown to
the normal position and tighten it.
•The date and day change at around 0:00 a.m. Take care to set a.m.
and p.m. correctly by referring to the 24 hour hand or calendar
•Turn the minute hand 4-5 minutes past the correct time and
then turn it back to the correct time. The time on the watch
can then be set to the correct time by pushing in the crown in
synchronization with a time service tone.
★Caution on setting the calendar
•Do not adjust the calendar while the time below is indicated:
Between 9:00 p.m. and 2:00 a.m.
The calendar may not change properly if the calendar is adjusted
in the period. Move the hands out of the period before the
calendar adjustment.
•Adjust the calendar at the beginning of the following months:
March, May, July, October, December.
The illustrations in this instruction manual may differ from the actual
watch in its design, the position of the crown and calendar, etc.
435A: three hands Plain models
Hour hand
Minute hand
Second hand
★Setting the time
1.Pull out the crown to position 1.
2.Turn the crown to set the time.
3.Push in the crown to position `.
G110: three hands with Date
★Setting the time
See page 8. (Pull out the crown to position 2)
★Setting the date
1.Pull out the crown to position 1.
2.Turn the crown to the left to set the date.
3.Push in the crown to position `.
J519: chronograph 30-minutes type
24-hours disk
Minute hand
Button B
Hour hand
minute disk
Second hand
second hand
⓪ ①②
Button A
★Setting the time
1.Pull out the crown to position 2.
2.Turn the crown to set the time.
•The 24-hour disk movement is linked with the hands.
3.Push in the crown to position `.
★Setting the date
1.Pull out the crown to position 1.
2.Turn the crown to the left to set the date.
3.Push in the crown to position `.
★Using the chronograph
•Pressing button B starts/stops/restarts measurement.
•To reset the chronograph, press button A while measurement is
•You can time up to 29 minutes and 59 seconds.
•The chronograph stops automatically after 30 minutes.
★Zero Positioning of Chronograph Hands
Button B
minute disk
⓪ ①②
Button A
second hand
<Adjusting the chronograph hands to the 0 position>
Adjust the chronograph hands to the 0 position (upright) when
they do not return to the 0 position after replacing the battery or
inflicting a strong shock.
1.Pull out the crown to position 2
2.Press button B to adjust the chronograph second hand to
the 0 position.
(The chronograph second hand moves counterclockwise when
you press button A.)
•The hand moves continuously by pressing and holding it.
3.Push in the crown to position `
4.Press the button A to reset the chronograph.
Check all the chronograph hands is set to the 0 position.
•While you adjust the chronograph hands, the watch is stopped.
Water Resistance
Water resistance
• Refer to the watch dial and the case back for the indication of the water resistance of
your watch. while skin diving, but not while scuba or saturated diving using helium gas.
The following chart provides examples of use for reference to ensure that your watch is
used properly. (The unit "1bar" is roughly equal to 1 atmosphere.)
• WATER RESIST(ANT) ××bar may also be indicated as W.R.××bar.
• Non-water resistant models are not designed to come into contact with any moisture.
Take care not to expose a watch with this rating to any type of moisture.
• Water resistance for daily use (to 3 atmospheres) means the watch is water resistant for
occasional accidental splashing.
Dial or Case back
Non-water resistant
Everyday-use water
resistant watch
Upgraded everyday use
water-resistant watch
Non-water resistant
Water-resistant to 3
5 bar
Water-resistant to 5
10/20 bar
Water-resistant to 10 or 20
• Upgraded water resistance for daily use (to 5 atmospheres) means that the watch may
be worn while swimming, but is not to worn while skin diving.
• Upgraded water resistance for daily use (to 10/20 atmospheres) means that the watch
may be worn
• Refer to the watch dial and the case back for the indication of the water resistance of
your watch. while skin diving, but not while scuba or saturated diving using helium gas.
Water-related use
Minor exposure Swimming
and general
to water
(washing face,
rain, etc.)
Skin diving,
marine sports
Scuba diving
using an air
Operate the
crown or button
when the watch
is wet
Precautionary Items and Usage Limitations
To Avoid Injury
• Be particularly careful when wearing your watch while holding a small child, to
avoid injury.
• Be particularly careful when engaged in strenuous exercise or work, to avoid
injury to yourself and others.
• Do NOT wear your watch while in a sauna or other location where your watch
may become excessively hot, since there is the risk of burns.
• Be careful when putting on and taking off your watch, since there is a risk of
damaging your fingernails, depending on the manner in which the band is
• Take off your watch before going to bed.
• Always use the watch with the crown pushed in (normal position). If the crown
is of the screw lock-type, make sure it is securely locked.
• Do NOT operate the crown or any push buttons when the watch is wet. Water
may enter the watch causing damage to vital components.
• If water enters the watch or the watch fogs up and does not clear up even after
a long time, consult your dealer or Authorized Service Center for inspection
and/or repair.
• Even if your watch has a high level of water resistance, please be careful of the
- If your watch is immersed in sea water, rinse thoroughly with fresh water and
wipe with a dry cloth.
- Do not pour water from a tap directly onto your watch.
- Take off your watch before taking a bath.
• If seawater enters the watch, place the watch in a box or plastic bag and
immediately take it in for repair. Otherwise, pressure inside the watch will
increase, and parts (crystal, crown, push button, etc.) may come off.
Wearing your Watch
• Leather, genuine skin and rubber (urethane) bands will deteriorate over time
due to perspiration, body oils and dirt. Be sure to replace the band periodically.
• The durability of a leather band may be affected when wet (fading, peeling of
adhesive), owing to the properties of the material. Moreover, wet leather may
cause a rash.
• It is recommended to take off the watch if it gets wet, even if the watch itself is
water resistant.
• Do not wear the band too tightly. Try to leave enough space between the band
and your skin to allow adequate ventilation.
• The rubber (urethane) band may be stained by dyes or soil present in or on
clothing or other accessories. Since these stains may not be removable,
caution is required when wearing your watch with items that tend to easily
transfer color (articles of clothing, purses, etc.). In addition, the band may be
deteriorated by solvents or moisture in the air. Replace with a new one when it
has lost elasticity or become cracked.
• Please request adjustment or repair of the band in the following cases:
- You notice an abnormality with the band due to corrosion.
- The pin of the band is protruding.
• We do not recommend attempting to adjust the watch band yourself. Special
expertise and experience is required for proper adjustment. If not adjusted
correctly, the band may become detached leading to loss of your watch. (Some
retailers may supply a band adjustment tool with your purchase).
For band adjustment, we recommend you consult the retailer from where the
watch was purchased or your nearest Authorized Citizen Service Center. Some
repair shops may charge a nominal fee for adjustment if the watch was not
purchased directly from them.
• The watch may stop or the function of the watch may be impaired in extremely
high or low temperature. Do not use the watch in places where the temperature
is outside the operating temperature range as stated in the specifications.
• Analog quartz watches are powered by a step motor that uses a magnet.
Subjecting the watch to strong magnetism from the outside can cause
the motor to operate improperly and prevent the watch from keeping time
accurately. Do not allow the watch to come into close proximity to magnetic
health devices (magnetic necklaces, magnetic elastic bands, etc.) or the
magnets used in the latches of refrigerator doors, clasps used in handbags, the
speaker of a cell phone, electromagnetic cooking devices and so on.
<Strong Shock>
• Avoid dropping the watch or subjecting it to other strong impact. It may cause
malfunctions and/ or performance deterioration as well as damage to the case
and bracelet.
<Static Electricity>
• The integrated circuits (IC) used in quartz watches are sensitive to static
electricity. Please note that the watch may operate erratically or not at all if
exposed to intense static electricity.
<Chemicals, Corrosive Gasses and Mercury>
• IIf paint thinner, benzene or other solvents or products containing these
solvents (including gasoline, nail-polish remover, cresol, bathroom cleaners
and adhesives, water repellent, etc.) are allowed to come into contact with
the watch, they may discolor, dissolve or crack the materials. Be careful
when handling these chemicals. Contact with mercury such as that used in
thermometers may also cause discoloration of the band and case.
<Protective Stickers>
• Be sure to remove any protective stickers that may be on your watch (case
back, band, clasp, etc.). Otherwise, perspiration or moisture may enter the
gaps between the protective stickers and the parts, which may result in a skin
rash and/or corrosion of the metal parts.
Always Keep Your Watch Clean
• Rotate the crown while it is pressed in fully and press the buttons periodically
so they do not become stuck due to accumulations of foreign matter.
• The case and band of the watch come into direct contact with the skin in the
same manner as undergarments. Corrosion of the metal or unnoticed soiling
such as that caused by perspiration and dirt can soil sleeves and other portions
of clothing. Keep your watch clean at all times.
• The case and band of the watch come into direct contact with the skin. If you
think there is something wrong, discontinue wearing the watch immediately
and consult your physician. In the case of accumulation of sweat or dirt on a
metal band or case, clean thoroughly using a brush and neutral detergent. In
the case of a leather band, wipe clean using a dry cloth.
• Leather bands may become discolored by perspiration or dirt. Always keep
your leather band clean by wiping with a dry cloth.
Caring for your Watch
• Wipe any dirt or moisture such as perspiration from the case and crystal with a
soft cloth.
• For a metallic, plastic or rubber (urethane) watchband, wash any dirt off with
Remove the small amounts of dirt trapped between the crevices of the metallic
band with a soft brush.
• For a leather band, wipe off dirt using a dry cloth.
• If you will not be using your watch for an extended period of time, carefully wipe
off any perspiration, dirt or moisture and store in a proper location, avoiding
locations subject to excessively high or low temperatures and high humidity.
Battery handling
• Do not attempt to recharge an old battery.
• Do not dispose an old battery into a fire.
• Keep batteries out of reach of children.
• In the event a battery is swallowed, immediately consult a physician.
• Do not disassemble,modify, or heat the battery. Doing so may cause an
• If a depleted battery is left in your watch, damage may be caused by
leakage of battery fluid. Be sure to replace the battery promptly.
• Always be sure to select a battery of the correct specifications when
replacing the battery.
<When Luminous Paint is used for your watch>
The paint on the dial and hands helps you with reading the time in a dark place.
The luminous paint stores light (daylight or artificial light) and glows in a dark
place. It is free from any radioactive substance or any other material harmful to
a human body or environment.
• The light emission gradually becomes weaker as time passes.
• The duration of the light (“glow”) will vary depending on the brightness,
types of and distance from a light source, exposure time, and the amount
of the paint.
• The paint may not glow and/or may dissipate quickly if exposure to light
was not sufficient.
Warranty and service
<Free Guarantee>
In the case a malfunction has occurred during the course of normal use while
the watch is still under warranty, the watch will be repaired free of charge in
accordance with the conditions of the warranty included with this manual.
<Stock Period of Repair Parts>
Our standard period for stocking repair parts for each model is generally seven
years. When an exterior part such as the watch case, glass, dial, hand, crown or
band is damaged, a spare part with different appearance may sometimes be used.
<Repair Period>
Repairs can be performed on your watch within the repair parts stock period even
after the free guarantee has expired. However, you will be charged for these repairs.
Please take the watch to the shop where you purchased it and ask whether it can
be repaired because the repair period varies according to the conditions of use,
environment and so forth. Moreover, there are cases in which it is difficult to restore
the watch to its original accuracy when decreased accuracy has resulted from
long-term use.
<Change of Address or Receiving as a Gift>
In the event that you have moved or have received your watch as a gift, and are not
able to bring your watch to the shop where it was purchased for servicing, please
consult Customer Support Center.
<Periodic Inspection (Charge Basis)>
• Water resistance
As the water resistance will be reduced over time, you should have your watch
inspected and its water resistance verified every 2-3 years (charge basis) to extend
its life and ensure safety. To maintain its water resistance, it is recommended to
request us to replace the packings and other parts of your watch.
• Disassembling for internal cleaning (repair)
You should have your watch disassembled and its internal components cleaned
periodically to extend its life. Lubrication oils are used to reduce wearing of moving
parts such as gears. However, over time the lubrication oils will degrade and wear
will increase, eventually resulting in malfunction. Please have your watch undergo
internal cleaning every 3-5 years (although the maintenance frequency depends on
the usage circumstances).
The battery was installed in your watch at factory is a monitor-use battery which
monitors the functions and special features of your watch. You should keep in mind
that the life of your battery could be shorter than the specified period is up.
Even in the event that the battery runs out before the time specified in the
guarantee, there will be a fee for replacing the battery.
<Other Inquiries>
If you have any questions regarding the warranty, repairs or other matters, please
inquire at the shop where you purchased your watch or Customer Support Center.
Guarantee policy:
•Guarantee exclusion
In the cases below you will be charged for repair even during the
guarantee period.
•Leather band repair/replacement. Battery replacement and changes in
appearance in the course of normal use (stains and scratches on the
glass, watch case, straps, bands, bracelets).
•Any malfunction or damage caused by repairing or modifying the watch
yourself or through mistreatment or negligence.
•No valid guarantee is presented.
•No store name or date of purchase is on the guarantee, or the name or
date is altered.
•Any malfunction or damage caused by natural disasters, fire, or other
•Manner of guarantee
The guarantee covers your watch for repair and maintenance.
Spare parts with a different appearance may sometimes be used when
repairing exterior parts such as the glass, watch case, face, hands, or
When it is difficult to repair the watch, an equivalent may be provided
instead of repairing it.
* The personal information on the guarantee shall not be used for
any other purpose than the warranty of the product.
* The terms and conditions of this guarantee are in addition to
and does not in any way affect your statutory or legal rights as a
* The guarantee card will not be reissued. Keep this guarantee in a
safe place.
This guarantee is valid only in the country where you purchased the
VAG19 1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF