sell sheet SC9120LBLA copy

sell sheet SC9120LBLA copy
COMBINATION
ALARM
IONIZATION SMOKE & CO
SC9120LBLA
120V AC, 60Hz Wire-in with 10 Year sealed battery backup
SEPARATE SMOKE AND
CARBON MONOXIDE
SENSORS DETECTS
BOTH DANGERS
10-YEAR SEALED
LITHIUM BATTERY
DUAL IONIZATION
120V AC,
60HZ HARDWIRE
LATCHING ALARM
INDICATOR
SINGLE BUTTON
TEST/SILENCE
TWO LATCHING
FEATURES
10-YEAR LIMITED
WARRANTY
LOUD 85DB ALARM
10
IONIZATION
The BRK Brands, Inc. model SC9120LBLA is a wire-in, 120 VAC 60Hz single and / or
multiple station smoke and carbon monoxide alarm specifically designed for
residential and institutional applications including sleeping rooms of hospitals, hotels,
motels, dormitories and other multi-family dwellings as defined in standard NFPA 101.
Model SC9120LBLA complies with CAN/ULC S531. They meet building codes where AC/DC
smoke and carbon monoxide alarms are required either separately or in combination.
The alarms are interconnectable up to 18 devices, of which 12 can be smoke alarms.
The BRK® SC9120LBLA features a dual ionization smoke sensing chamber - screened for
insect protection and a carbon monoxide sensor, an 85dB horn, 9V battery back-up and
a “silence” feature. The “Intelligent SensingTechnology” system is designed to reduce
nuisance alarms. “Latching Alarm Indication” remembers which unit initiated an alarm.
When interconnected in a series, the unit that triggered the alarm rapidly flashes its red
LED indicator. After the alarm condition subsides, the initiating unit will store in memory or
“latch” the information and begin to flash the Red LED indicator 2 seconds on, 2 seconds
off. The “Perfect Mount” system features a gasketless base and a mounting bracket that
keeps the alarm secure over a wide rotation range to allow for true alignment. This will allow
fine-tuning on the positioning to compensate for out of aligned wall studs and to keep
the wording level when wall mounting. A Single button test/silence button eliminates
confusion. Depending on what mode the alarm is in, pushing the button will test, silence,
re-test the alarm when in silence and clear the latching feature. Battery installation and
removal can occur while the unit is mounted to the ceiling or wall via the side load battery
compartment. Other Contractor Preferred features include a dust cover to keep alarm
clean during construction, keyhole slots in the mounting bracket eliminate the need to
remove the electrical box screws for installation. Two locking features are provided to prevent
battery theft and/or theft of the unit. Connection to AC power is made with a “Quick-Connect”
wiring harness. Installation is quick, easy and cost effective.
CAT.
SC9120LBLA
FRONT
VIEW
SIDE
VIEW
MOUNTING
BRACKET
TECHNICAL SPECS
5.58"
1.97"
ARCHITECTURAL AND ENGINEERING SPEC
TOP VIEW
MOUNTING BRACKET
SIDE VIEW
The combination
smoke & carbon monoxide
alarm shall be
BRK Electronics model
SC9120BA and shall provide at a minimum the following features and functions:
1. A permanently installed carbon monoxide sensor and a dual ionization
smoke sensor.
2. Powered by 120V AC, 60Hz and have a monitored lithium battery backup. In battery
backup mode, the battery must last for 8 hours minimum in standby and then
12 hours minimum in alarm.
3. A visual LED (green) power-on indicator to confirm unit is receiving AC power
and a (green intermittent) indicator to confirm unit has switched to battery
backup mode. A red LED to indicate when in smoke alarm and another red LED
to indicate when in CO alarm.
4. The CO sensor is adjusted not to detect CO levels below 30 PPM and will not
alarm when exposed to constant levels of 30 PPM for 30 days. It will alarm
at the following levels: 400 PPM CO between 4 and 15 minutes, 150 PPM CO
between 10 and 50 minutes and 70 PPM CO between 60 and 240 minutes.
5. A test/silence button to check all alarm functions and to silence any nuisance
alarms. In addition, the unit shall have a low battery silence feature to quiet the
low battery chirp for up to eight hours.
6. The unit shall perform self diagnostic tests every second and issue a
malfunction warning (three rapid chirps) if the unit malfunctions.
7. A solid state piezo horn rated at 85dB at 10 feet that provides a repeating
horn pattern. Smoke Alarm: 3 beeps, pause, 3 beeps, pause; CO Alarm: 4 rapid
beeps, pause, 4 rapid beeps, pause.
8. The unit shall be capable of operating between 40 degrees F (4 degrees C) and
100 degrees F (38 degrees C) and relative humidity between 10% and 95%.
9. The unit shall center mount to any standard electrical junction box up to 4 inch
diagonal without screw removal. Larger boxes may require an adapter plate.
10. The unit shall have an optional locking mechanism to deter theft of battery
and/or theft of the unit.
11. The unit shall have a plug in connector and be capable of interconnection of
up to 18 alarms.
12. The unit shall have a gasketless base for easy installation and be capable
of keeping alarm secure over a wide rotation range to allow for true
alarm alignment.
13. The unit shall at a minimum meet the requirements of CAN/ULC S531.
INSTALLATION OF ALARM
Installation of this smoke alarm must conform to all Canadian electrical code
Interconnected units must meet the following requirements: wire gauge to
be per local codes. It is recommended that all units be on the same fuse
or circuit breaker. If local codes do not permit, be sure the neutral wire is common
to both phases.
Alarm Dimensions:
5.58" dia x 1.97"H
Weight:
8.5 oz
Operating Voltage:
120V AC 60Hz pure sine wave w/Sealed Lithium battery
backup
Operating Current:
.09 amps (standby/alarm)
Temperature Range:
40 degrees F (4 degrees C) to 100 degrees F
(38 degrees C)
Humidity Range:
10% to 95% relative humidity (RH)
Audio Alarm:
85dB at 10 feet
Test/Silence:
Electronically simulates a smoke or carbon monoxide condition, causing the unit to alarm.
Alarm Reset:
Automatic when Smoke and/or CO clears
Press test/silence button to reset manually.
Interconnections:
(see user’s manual).
Smoke Sensor:
Dual Ionization CO Sensor Metal Oxide
Indicator Lights:
AC Power:
Constant Green LED
DC Power:
Intermittent Green LED
Local Alarm:
Red LED flashes rapidly
Remote Alarm:
Red LED out Latching Alarm: Red LED flashes
every 5 seconds after local alarm stops
Listing:
CAN/ULC S531
SHIPPING SPECS:
Individual Carton Dimensions:
5.69"L x 2.25"W x 5.59"H
Weight:
.69 lbs.
Cube:
.043 ft3
UPC:
0 29054 01758 1
Master Carton Dimensions:
14.43"L X 6.19"W X 12.63"H
Master Pack:
12
Weight:
9.15 lbs.
Cube:
.65 ft3
I2of5:
100 29054 01758 8
Pallet Information:
Cases per Layer:
19
Number of Layers:
3
Cases per Pallet:
57
Cube:
42.2 ft3
Weight:
566.55 lbs.
©2016 BRK Brands, Inc. Dicon Global Inc.,
All rights reserved
www.brkcanada.ca
www.firstalert.ca
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement