Draper Ultimate Access/Series V

Draper Ultimate Access/Series V
Installation/Operating Instructions
220V Ultimate Access Electric Projection Screen by Draper
These Installation/Operating Instructions are available in the official language
of the country where you purchase the product. Please contact your distributor
to request a copy.
Vous pourriez demander les instructions d’installation et d’opération traduises
dans la langue officielle du pays ou vous achetez le produit. Veuillez
demander à votre distributeur.
Die Gebrauchsanweisung für Installation und Konstruktion sind in der
offiziellen Sprache des Landes, indem Sie das Produkt gekauft haben,
vorhanden. Fragen Sie die jeweilige Verkaufs-Abteilung.
Caution
① Read instructions through completely before proceeding.
② Follow instructions carefully. Installation contrary to instructions
invalidates warranty.
③ Entire bottom of screen case should be unobstructed to permit
access to bottom panel for electrical connections or servicing.
④ Screen should be installed level (using a carpenter’s level).
⑤ Nothing should be fastened to screen dowel or viewing surface.
⑥ Operating switch(es) and mounting brackets are packed separately
in screen car ton. Do not discard with packing material.
⑦ Screen operates on 220 V AC, 50 Hz. current.
NOTE: Screen has been thoroughly inspected and tested at factory and
found to be operating properly prior to shipment.
Hanging Screen
When locating viewing surface and checking clearance for screen’s operation,
remember surface is centered in the length of the case.
Screen is normally recessed above ceiling and may be installed in a variety
of ways. See typical installations detailed on page 3. Regardless of mounting
method used, the following points apply:
① Mounting brackets are packed separately in carton. Engage each
bracket with top of housing as shown below and tighten set screws. A
bracket should be within 46 cm from each end of screen case. Brackets
can be removed and case mounted with lag screws through top of case
(holes drilled on site).
② Screen should be positively and securely supported so that vibration or
even abusive pulling on viewing surface will not weaken installation.
③ Installer must insure that fasteners used are of adequate strength and
suitable for the mounting surface chosen.
④ Entire bottom of case must be readily accessible after installation is
complete.
⑤ The bottom access panel, trap door, and lower edge of the case are
joined with continuous hinge joints and must operate freely. Front and
back of case must be straight–not forced to warp or bow. Hinge joints
Remove shipping brackets
before operating screen.
Slots along top of case permit
brackets to be set at an angle
Typical Installation
Dowel
Shipping
Bracket
US Patent Nos. 5,341,241; 6,137,629;
6,421,175; 6,532,109; 6,816,308; 7,559,707
must be free of mastic or paint build up, and trapdoor and access panel
must be unobstructed by ceiling tiles.
⑥ If case is painted on location, removal of roller/fabric assembly is
recommended prior to painting. If not removed, slots on bottom of case
should be shielded to protect viewing surface from paint splatters or
overspray.
⑦ Do not seal unit in ceiling until electrical connections have been made
and screen has been operated successfully.
Electrical Connections
Screen operates on 220 V AC, 50 Hz. current.
Junction box is located just above the bottom access panel at left end of
screen.
Open the access panel/trap door for access to the junction box cover. (See
bottom access panel/trap door opening and closing instructions below).
Remove two (2) hex head screws that secure the cover to the junction box to
expose the brown, black, and blue pigtail leads and the green ground wire per
wiring diagram on page 4.
If optional low voltage control or video interface control is specified and factory
installed, please refer to wiring diagram on page 4.
Screen is shipped with internal wiring complete and control switch(es) fully
boxed. Wire to connect screen to switch(es) and switch(es) to power supply
should be furnished by installer. Connections should be made in accordance
with attached wiring diagram, and wiring should comply with national and
local electrical codes.
All operating switches should be “off” before power is connected.
Bottom Access Panel/Trap Door Opening & Closing
After screen case has been mounted, remove the dowel shipping brackets
from dowel if provided. A spring latch at each end of the trap door holds
this assembly closed. In some screens there will also be a spring latch
near the center of the case. To gain access to inside of screen case, disengage spring latch at each end of the case (and near the center of the case, if
applicable) by sliding the latch lever towards the center of screen case, then
pull down slightly on the trap door assembly. The latch levers are somewhat
concealed from view. Locate these with the trap door open by feeling for the
vertical latch lever above the door about 8 cm from case endcaps and near
the center of the case.
The assembly will swing down, opening about 135°. Pivot the prop arms at
each end of the trap door assembly towards the ends of screen case. Prop
arms engage with a hole in each endcap to hold the trap door assembly fully
open. To close the trap door assembly disengage prop arms from endcaps
and pivot these over the access panel. Swing the trap door assembly upward,
stopping just before the latch levers hit the bottom flanges of the endcaps
(and center of case where appropriate). Pull levers of latches towards center
of screen case to allow the trap door assembly to be pivoted to its closed position. Make sure that the spring latch levers engage fully with case endcaps
(and center of case where appropriate).
Alternate
Installation
(additional
set of brackets required
but not included)
Caution: Beware of pinch
points along closure
®
Case dimensions
on page 4.
Copyright © 2011 Draper Inc.
Form UltimateAccess220V_Inst11-R
Printed in U.S.A.
If you encounter any difficulties installing or servicing your Ultimate Access screen, call
your dealer or Draper, Inc., in Spiceland, Indiana, 765/987-7999 or fax 765/987-1689.
220V Ultimate Access by Draper
Page 2 of 4
Motorized Roller/Fabric Installation
Operation
The bottom access panel/trap door assembly must be opened and placed in fully
opened position first.
When screen is first operated, be cautious! Cycle unit down and up
several times to confirm satisfactory operation.
220V SINGLE STATION CONTROL—3-position UP-OFF-DOWN switch
permits operation to be stopped at any point. Factory adjusted limit switches automatically stop screen when fully down or fully up.
220V MULTIPLE STATION CONTROL—(Not CE approved) Switches are
similar in appearance to 220V Single Station Control. Screen stops when
switch is released and may be restarted in either direction. Factory adjusted limit switches stop screen automatically when fully up or fully down.
24V MULTIPLE STATION CONTROL—Three-button UP-STOP-DOWN
switches stop at any point desired, operate in any sequence. Factory
adjusted limit switches automatically stop screen when fully up or down.
220V & 12V VIDEO INTERFACE CONTROL—(Not CE Approved). Allows
screen to be controlled by a trigger signal—when signal comes on, screen
descends automatically. Two versions: Model VIC220 integrates screen operation with a DRAPER video projector lift or a video projector or tuner with
a 220V switched outlet. Model VIC12 interfaces with 12V switched outlet.
Both available with override switch (VIC–OS), permitting independent
operation. VIC–OS not available with factory installed VIC220 & VIC12.
KEY OPERATED SWITCHING—Two kinds of key-operated switches are
optionally available with this unit.
① The key-operated power supply switch controls power to screen and
switches. When it is “off”, the switches will not operate screen. Key
may be removed from the switch in either “on” or “off” position.
② A three-position key switch permits screen to be operated directly by
key. In this case, the screen’s operator must always have a key.
RS232/Ethernet—Serial communication and network communication
optionally available with wall switches, RF or IR remote.
The motor end mounting bracket has a metal bracket with snap ring for accepting motor head. Back out the four set screws in bracket until they are flush
with top side of bracket.
To engage the motor end bracket flange above the two channels in the top of the
screen housing, rotate the bracket approximately 45° counterclockwise to allow
the top surface of the motor bracket to rest flat against the top inside of the housing. Rotating the bracket clockwise until it is engaged with the channels, slide it
along the length of the housing against the electrical junction box.
Engage the idler end bracket (rectangular mounting pad) in the same manner as
the motor end bracket and slide it toward the opposite end of the screen housing.
Do not tighten the set screws on the brackets until the roller/fabric assembly is
installed, and centered in the case.
Locate the black washer and retaining clip.
Note: This will require two people to
perform safely. Raise the roller/fabric
assembly up into the screen housing and
engage the head of the motor completely
into the motor mounting bracket, making
sure the snap ring engages with the motor
and that the limit switch adjusting knobs
are visible from the bottom of the screen
housing.
While supporting the idler end of the roller,
slide the idler end mounting bracket toward
Retaining
clip
the roller. Insert the roller pin into the nylon
bushing on the idler end mounting bracket. Motor roller
Washer
assembly
The roller idler pin needs to go through
Idler end roller
the idler bracket far enough to allow the
mounting bracket
washer and retaining clip to be reinstalled
on the pin.
Failure to replace the washer and retaining
clip as shown could result in the separation of the roller from the brackets.
Adjustments
Please Note: Screen limits are factory set for optimum performance
of the screen. Any adjustment of these limits could void the warranty. Please check with Draper prior to resetting screen limits.
CAUTION: Always be prepared to shut screen off manually when
new adjustment is being tested. Screen may be severely damaged if
viewing surface is allowed to run too far up or too far down.
CAUTION: Be sure all switches are in “off” position before adjusting limit switches.
Fabric unrolling from back
of roller
The roller/fabric assembly and roller
brackets may need to be slid left or right in
mounting channel of case to center fabric
within screen case.
Left hand motor
White Socket—Down
Yellow Socket—Up
Securely tighten the set screws on the
roller mounting brackets.
Connect the electrical plug from the motor
to the mating socket on the junction box.
Close the bottom access panel/trap door
as previously described.
Motorized Roller/Fabric Removal
Reverse the instructions above, under
“Motorized Roller/Fabric Installation,” for removal of the unit.
www.draperinc.com
Fabric unrolling from front
of roller
Left hand motor
Audience
side
White Socket—Up
Yellow Socket—Down
Audience
side
ADJUSTING WHITE SOCKET—White socket is located on motor end of
screen roller and is accessible to a small flat screwdriver or a 4 mm (5/32")
hex key. Turning socket counterclockwise will allow the roller to run farther
up or down (as appropriate). Turning it clockwise will shorten operation,
causing screen to stop sooner. One full revolution of the socket will alter
the stopping position of the viewing surface by approximately 32 mm.
ADJUSTING YELLOW SOCKET—Yellow socket is located on the motor
end of screen roller and is accessible to a small flat screwdriver or a 4 mm
(5/32") hex key. Turning the socket counterclockwise will allow the roller to
run farther up or down (as appropriate). Turning it clockwise will cause the
roller to stop sooner. One full revolution of the socket will alter the stopping
position of the viewing surface by approximately 32 mm.
AT NO TIME SHOULD VIEWING SURFACE BE UNROLLED ENOUGH
TO EXPOSE ANY PART OF SCREEN ROLLER.
(765) 987-7999
220V Ultimate Access by Draper
Page 3 of 4
Tab-Tension Adjustment Procedure for Ultimate Access/Series V
① Determine which side requires adjustment.
② Secure dowel with one hand.
Caution: Do not touch or bend surface.
③ Using Philips-head screwdriver, depress spring-loaded adjustment
screw (see drawing) and slowly turn clockwise to tighten tension, or
counterclockwise to loosen tension. The screw adjusts in ¼ turn
increments. Adjust only one increment (¼ turn).
④ If problem is not corrected, leave screen in position for 24 hours to allow
surface material to stretch into position.
⑤ If problem still is not corrected, repeat steps 2 and 3.
Tensioning
Cable
Dowel
Adjustment
Screw
Case Dimensions
Mounting brackets slide
left and right as needed.
229 mm
191 mm
25
mm
254
mm
243
mm
16
mm
L*
Series E
Viewing Surface
203 mm
Ceiling tile
(by others)
173
mm
121
mm
*L =
Series E
208 mm
Series V
Viewing Surface
Series V
Varies
Alternative mounting configuration
243
mm
www.draperinc.com
(765) 987-7999
21/8"
220V Ultimate Access by Draper
Page 4 of 4
Wiring Diagrams
Please Note: Do not wire motors in parallel.
Single Station Control
Junction box at
eft end of screen
Junction box at
left end of screen
CE Approved
Multiple Station Control
Not CE Approved
Internal Screen Wiring
Blue-220v (Common)
Brown-220v (Down)
Black-220v (Up)
Internal Screen Wiring
Blue-220v (Common)
Brown-220v (Down)
Black-220v (Up)
Green/Yellow (Motor Ground)
Green/Yellow (Motor Ground)
Cap off with wire
nut & tape
Blue
Red
Black
Control
switch
Blue
Black
L1
Blue
Red
Black
Neutral
220v,
50 Hz.
Hot
Dashed wiring
by installer
Neutral
Red
Dashed wiring
by installer
220v, 50 Hz.
Low Voltage & Wireless Control
Internal Screen Wiring
White/Blue (Common)
Red 110/Black 220 (Up)
Black 110/Brown 220 (Down)
Green/Yellow
(Motor Ground)
White or Blue-Common to screen & 110/220V AC Neutral
Red-to screen (directional)
Brown-to screen (directional)
Yellow-to 110/220V AC-Hot
Black-to 110/220V AC-Hot
Green/Yellow (Ground)
Dashed wiring by electrician
Low voltage wiring by others
Eye Port for IR Eye, RF Receiver or LED
Wall Switch. For more than one of
these, a splitter is required.
3 Button Wall Switch
DOWN - Black
COM - White
UP - Red
Aux Port for connecting additional LVC-III
modules (up to six total can be linkedconnect from Aux to Eye).
To
110/220V
Line
STOP
Location of key
operated on-off
switch if furnished
STOP
Control
Switches
24v DC
MC1
Internal Screen Wiring
Program LED
White or Blue-Common
Red-to Screen (directional)
Black-to Screen (directional)
Brown-Hot to AC
Green/Yellow-Ground
White/Blue (Common)
Red 110/Black 220 (Up)
Black 110/Brown 220 (Down)
Green 110V/
Green/Yellow 220V
(Motor Ground)
Low Voltage Wiring by others
AC Wiring by electrician
Fuse
RS232 Data FROM Control System
RS232 Data TO Control System
Signal Ground & Manual Switch Common
Manual Switch Down
Manual Switch Up
MC1
Location of key
operated on-off
Eye Port for IR Eye. For RF Receiver or LED
switch if furnished
Wall Switch, a Splitter and a Power Supply
is required. Plug RF Receiver or LED Wall
Switch and Power Supply into splitter, then
run cable from Splitter to MC1 Eye Port.
To AC Line
See separate Serial Communication-RS232 Instruction sheet for enabling RS232 with the MC1.
www.draperinc.com
(765) 987-7999
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement