Panasonic | SC-BTT270 | Owner`s manual | Panasonic SC-BTT270 home cinema system

VQT3D27~Cover_eng.fm 1 ページ
2011年1月6日 木曜日 午後1時21分
Owner’s Manual
Blu-ray DiscTM Home Theater Sound System
Model No. SC-BTT770
SC-BTT370
SC-BTT270
SC-BTT273
The illustration shows the image of the unit SC-BTT770.
Dear customer
Thank you for purchasing this product.
For optimum performance and safety, please read these instructions carefully.
Before connecting, operating or adjusting this product, please read the instructions completely.
Please keep this manual for future reference.
If you have any questions contact
U.S.A. and Puerto Rico : 1-800-211-PANA(7262)
Canada : 1-800-561-5505
P
PC
VQT3D27-3
VQT3D27~Safety_eng.fm
2 ページ
2010年12月27日 月曜日 午後4時14分
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
FCC Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
≥ Reorient or relocate the receiving antenna.
≥ Increase the separation between the equipment and receiver.
≥ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
≥ Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:To assure continued compliance, follow the attached
installation instructions and use only shielded interface cables when
connecting to peripheral devices. Any changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way
Secaucus, NJ 07094
Support Contact:
Panasonic Consumer Electronics Company
Telephone No.: 1-800-211-PANA (7262)
[BTT770]
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
FCC Note:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
≥ Reorient or relocate the receiving antenna.
≥ Increase the separation between the equipment and receiver.
≥ Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
≥ Consult the dealer or an experienced radio/TV technician for help.
FCC caution: To maintain compliance with FCC regulations, shielded
interface cables must be used with this equipment. Operation with
non-approved equipment or unshielded cables may result in interference
to radio and TV reception. Any changes or modifications not approved by
the party responsible for compliance could void the user’s authority to
operate this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Responsible Party:
Panasonic Corporation of North America
One Panasonic Way, Secaucus, NJ 07094
Support Contact:
Panasonic Consumer Electronics Company
Telephone No.: 1-800-211-PANA (7262)
THE FOLLOWING APPLIES IN THE U.S.A. AND CANADA
This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation
of this device.
Contains FCC ID: RYYWYPAEBUX4
Contains IC:4389B-WYPAEBUX4
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.
This product is restricted to indoor use due to its operation in the 5.15 to
5.25 GHz frequency range.
FCC and IC require this product to be used indoors for the frequency range
5.15 to 5.25 GHz to reduce the potential for harmful interference to
co-channel Mobile Satellite systems. High power radars are allocated as
primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These
radar stations can cause interference with and/or damage this product.
This equipment complies with FCC/IC radiation exposure limits set forth for
an uncontrolled environment and meets the FCC radio frequency (RF)
Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC
radio frequency (RF) Exposure rules. This equipment has very low levels of
RF energy that it deemed to comply without maximum permissive exposure
evaluation (MPE). But it is desirable that it should be installed and operated
keeping the radiator at least 20cm or more away from person’s body
(excluding extremities: hands, wrists, feet and ankles).
WARNING:
To satisfy FCC RF exposure requirements for mobile transmitting devices,
a separation distance of 20 cm or more should be maintained between the
antenna of this device and persons during device operation.
To ensure compliance, operations at closer than this distance is not
recommended. The antenna used for this transmitter must not be
co-located in conjunction with any other antenna or transmitter.
[BTT770]
THE FOLLOWING APPLIES ONLY IN CANADA.
This Class B digital apparatus complies with Canadian ICES-003.
[BTT770] [BTT370]
THE FOLLOWING APPLIES ONLY IN CANADA.
For main unit
Product Identification Marking is located on the bottom of the unit.
[BTT770]
For wireless system
Product Identification Marking is located on the bottom of wireless system.
VQT3D27
2
VQT3D27~Safety_eng.fm
3 ページ
2010年12月27日 月曜日 午後3時57分
IMPORTANT SAFETY
INSTRUCTIONS
Read these operating instructions carefully before using the unit. Follow the
safety instructions on the unit and the applicable safety instructions listed
below. Keep these operating instructions handy for future reference.
1
Read these instructions.
2
Keep these instructions.
3
Heed all warnings.
4
Follow all instructions.
5
Do not use this apparatus near water.
6
Clean only with dry cloth.
7
Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9
Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other.
A grounding-type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for replacement of
the obsolete outlet.
10 Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11 Only use attachments/accessories specified by the manufacturer.
12 Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid injury
from tip-over.
13 Unplug this apparatus during lightning storms or when
unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain
or moisture, does not operate normally, or has been dropped.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be
of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
(Inside of product)
WARNING
Unit
To reduce the risk of fire, electric shock or product damage,
– Do not expose this unit to rain, moisture, dripping or splashing.
– Do not place objects filled with liquids, such as vases, on this unit.
– Use only the recommended accessories.
– Do not remove covers.
– Do not repair this unit by yourself. Refer servicing to qualified service
personnel.
-If you see this symbolInformation on Disposal in other Countries outside the
European Union
This symbol is only valid in the European
Union.
If you wish to discard this product, please
contact your local authorities or dealer and ask
for the correct method of disposal.
CAUTION
Unit
– This unit utilizes a laser. Use of controls or adjustments or performance of
procedures other than those specified herein may result in hazardous
radiation exposure.
– Do not place sources of naked flames, such as lighted candles, on this unit.
Placement
To reduce the risk of fire, electric shock or product damage,
– Do not install or place this unit in a bookcase, built-in cabinet or in another
confined space. Ensure this unit is well ventilated.
– Do not obstruct this unit’s ventilation openings with newspapers,
tablecloths, curtains, and similar items.
VQT3D27
3
SC-BTT770_370_270P_eng.book 4 ページ
2010年12月16日 木曜日 午後9時51分
Table of contents
IMPORTANT SAFETY INSTRUCTIONS ......... 3
Getting started
Radio
Accessory......................................................... 5
Control reference guide.................................... 6
Listening to the Radio..................................... 29
•Remote control ................................................................. 6
•Main unit (Front) ............................................................... 7
•POWER-SAVING FEATURES .................................. 7
•Main unit (Rear)................................................................ 7
Playable discs/Cards........................................ 8
Unit and media care ......................................... 9
Using the remote control .................................. 9
STEP 1 : Preparing the speakers................... 10
•Assembling the speakers ............................................... 10
•Preparing cables and making connection ...................... 11
STEP 2 : Positioning ...................................... 12
STEP 3: Connections..................................... 13
•Speaker cable connection ..............................................
•Connection to a TV ........................................................
•Connection with Set Top Box, etc. .................................
•Radio antenna connection .............................................
•[BTT770] Digital transmitter connection............................
•Connection to a broadband network ..............................
13
14
16
16
17
17
STEP 4:
AC power supply cord connection.................. 18
STEP 5: [BTT770]
Preparing the wireless system ....................... 18
STEP 6: Easy setup ....................................... 19
•Network Easy Setting ..................................................... 20
•Reprogramming the remote control................................ 21
•Firmware updates........................................................... 22
Inserting or removing media........................... 22
HOME menu .................................................. 23
Enjoying sound effects from all speakers....... 24
•Enjoying surround sound effects .................................... 24
Playback
Playing video contents ................................... 25
•Other operations during play .......................................... 25
•Useful functions.............................................................. 26
•Enjoying BD-Live or picture-in-picture in BD-Video........ 26
Enjoying 3D video .......................................... 27
•3D settings ..................................................................... 27
•Useful functions.............................................................. 27
Playing still pictures........................................ 28
•Useful functions.............................................................. 28
Playing music ................................................. 29
•Playing a track in another folder..................................... 29
VQT3D27
4
•Presetting stations automatically ................................... 29
•Presetting stations manually.......................................... 29
•Listening/confirming the preset channels ...................... 30
TV
Enjoying TV with unit’s speakers.................... 30
•Surround sound effects.................................................. 30
•Sound modes................................................................. 30
Linked operations with the TV
(VIERA LinkTM “HDAVI ControlTM”).................. 31
•Setting the audio link ..................................................... 31
•Easy control only with VIERA remote control ................ 32
Other devices
Using the iPod/iPhone .................................... 32
•iPod/iPhone Connection ................................................ 32
•iPod/iPhone Playback.................................................... 33
Advanced operations
Enjoying VIERA CASTTM ................................ 34
Playback menu ............................................... 35
Setup menu .................................................... 37
•Speaker settings ............................................................ 41
Optional speaker settings
Speaker installation option ............................. 42
Reference
Troubleshooting guide .................................... 43
Messages ....................................................... 45
Supplemental information............................... 46
Specifications ................................................. 48
Limited Warranty (ONLY FOR U.S.A.
AND PUERTO RICO)..................................... 50
Limited Warranty (Only for CANADA) ............ 51
Index................................................. Back cover
2011年1月7日 金曜日 午前9時36分
≥ This Owner’s Manual is applicable to models
SC-BTT770, SC-BTT370, SC-BTT270 and SC-BTT273.
Unless otherwise indicated, illustrations in this Owner’s
Manual are of SC-BTT770.
≥ Operations in this Owner’s Manual are described mainly
with the remote control, but you can perform the
operations on the main unit if the controls are the same.
Indicates features applicable to:
[BTT770]: SC-BTT770 only
[BTT370]: SC-BTT370 only
[BTT270]: SC-BTT270 only
[BTT273]: SC-BTT273 only
System
SC-BTT770
SC-BTT370
SC-BTT270
SC-BTT273
Main unit
SA-BTT770
SA-BTT370
SA-BTT270
SA-BTT273
Front speakers
SB-HF775
SB-HF370
SB-HF270
SB-HF370
Center speaker
SB-HC775
SB-HC370
SB-HC270
SB-HC370
Speaker system
Surround speakers
Subwoofer
Wireless system (with digital transmitter)
SB-HS270
SB-HS270
SB-HS270
SB-HS270
SB-HW370
SB-HW370
SB-HW270
SB-HW270
SH-FX71
—
—
—
Getting started
Getting started
Playback
VQT3D27~Body_mst.fm 5 ページ
Radio
≥ Some accessories and external devices mentioned in this Owner’s Manual that are not included with this product may
not be on sale in certain regions.
≥ Please note that the actual controls and components, menu items, etc. of your Blu-ray Disc Home Theater Sound
System may look somewhat different from those shown in the illustrations in this Owner’s Manual.
Accessory
[BTT770]
[BTT370]
[BTT270]
[BTT273]
∏ 1 Remote control
(N2QAYB000632)
∏ 1 Remote control
(N2QAYB000632)
∏ 1 Remote control
(N2QAYB000629)
∏ 1 Remote control
(N2QAYB000629)
∏ 2 Batteries for remote
control
∏ 2 Batteries for remote
control
∏ 2 Batteries for remote
control
∏ 2 Batteries for remote
control
TV
Check the supplied accessories before using this unit.
For accessories of speakers, refer to page 10.
∏ 1 Sheet of speaker cable ∏ 1 Sheet of speaker cable ∏ 1 Sheet of speaker cable ∏ 1 Sheet of speaker cable
sticker
sticker
sticker
sticker
∏ 1 FM indoor antenna
(RSAX0002)
∏ 1 FM indoor antenna
(RSAX0002)
∏ 1 FM indoor antenna
(RSAX0002)
Other devices
∏ 1 FM indoor antenna
(RSAX0002)
≥ Product numbers provided in this Owner’s Manual correct as of December
2010. These may be subject to change.
≥ Do not use AC power supply cord with other equipment.
≥ [For_U.S.A._and_Puerto_Rico.]: To order accessories, refer to “Accessory
Purchases (United States and Puerto Rico)” on page 50.
[For_Canada]: To order accessories, call the dealer from whom you have
made your purchase.
Optional speaker
settings
[For_Canada]
The enclosed Canadian French label sheet corresponds to the
English display on the front and back side of the unit.
∏ 1 HDMI cable
(K1HA19DA0005)
Reference
∏ 1 Digital transmitter
(RFAX1012B)
Advanced operations
∏ 2 AC power supply cord ∏ 1 AC power supply cord ∏ 1 AC power supply cord ∏ 1 AC power supply cord
(K2CB2CB00021)
(K2CB2CB00021)
(K2CB2CB00021)
(K2CB2CB00021)
(RFAX0023) with a
ferrite core
VQT3D27
5
SC-BTT770_370_270P_eng.book 6 ページ
2010年12月16日 木曜日 午後9時51分
Control reference guide
Remote control
13
リワヱヶヵ
モヷ
1
1
2
2
14
15
3
4
ュリヴヤ
ㄊヱㄐㄅ
ヴユモンヤラ
ヱロモヺ
16
ヴユモンヤラ
ヴロヰヸ
ヴレリヱ
ヱモヶヴユ
5
ヴヵヰヱ
6
ヷリユンモ
チヤ モ
ヴ
6
ヵ
ヱ
19
ヶ
チヮユワ
ユワヶ
ヱチヮ
VQT3D27
18
ラヰヮユ
ヵヰヱ
8
ユヹリヵ
20
ノヶ
ヰヱ
7
17
ヴレリヱ
ンユヵヶンワ
9
21
10
11
12
22
23
Turn the unit on and off
Select title numbers, etc./Enter numbers or characters
( 34)
[CANCEL]: Cancel
3 Select the source ( 22)
4 Basic playback control buttons ( 25)
5 Select preset radio stations
6 Show status messages ( 25)
7 Display the Home screen of VIERA CAST ( 34)
8 Selection/OK, Frame-by-frame ( 25)
9 Show sub menu ( 26)
10 These buttons are used when;
≥ Operating a BD-Video disc that includes JavaTM
applications (BD-J).
≥ Operating contents of VIERA CAST ( 34)
11 Set the sound mode ( 24)/Select speaker channel
( 24)
12 Select surround sound effects ( 24)/Set the sleep timer
1 Press and hold [–SLEEP].
2 While “SLEEP ££” is displayed, press [–SLEEP]
several times to select the time (in minutes).
≥ Timer selection is up to 120 minutes.
≥ Select “OFF” when canceling the setting.
≥ To confirm the remaining time
Press and hold the button again.
13 TV operation buttons
[Í]: Turn the television on and off
[AV, INPUT]: Switch the input select
[i j VOL]: Adjust the volume
14 Adjust the volume of the main unit
15 Mute the sound
≥ “MUTE” flashes on the unit’s display, while the function is
on.
≥ To cancel, press the button again or adjust the volume.
≥ Muting is canceled if the unit is turned off.
16 Show NETFLIX screen
17 Select radio stations manually ( 29)
18 Exit the menu screen
19 Show HOME menu ( 23)
20 Show Pop-up menu/Top menu/Direct Navigator ( 25)
21 Return to previous screen
22 [BTT770] [BTT370] : Start up a video communication ( 34)
23 Show Playback menu ( 35)/Select audio ( 25)
VQT3D27~Body_mst.fm 7 ページ
2011年1月5日 水曜日 午前11時14分
1
2
POWER
Getting started
Main unit (Front)
3
VOL
OPEN/CLOSE
Pull open.
iPod
SD CARD
4
1
2
3
4
5
5
6
7
8
9
10
6
7
8
Start play (> 25)
SD card slot (> 22)
Remote control signal sensor
Distance: Within approx. 7 m (23 ft.)
Angle: Approx. 20o up and down, 30o left and right
9 Display
10 Connect iPod/iPhone (> 32)
Standby/on switch (POWER Í/I) (> 19)
Press to switch the unit from on to standby mode or vice
versa. In standby mode, the unit is still consuming a small
amount of power.
Open or close the disc tray (> 22)
Adjust the volume of the main unit
Disc tray
Stop (> 25)
POWER-SAVING FEATURES
The main unit is designed to conserve its power consumption and save energy.
[BTT770] [BTT370] Wireless system (SH-FX71) does not have this function.
≥ Automatic power-down function
The main unit will automatically switch to standby mode after
30 minutes if the main unit is inactive as follows.
e.g.
jThere is no audio signal from an external device.
jDisc playback is stopped/paused.
jiPod/iPhone playback is stopped/paused.
jThe disc menu is displayed and play is not selected.
(This function may not work depending on the application
type of discs.)
Main unit (Rear)
1
2
3Ω
6
5
3Ω
2
1
R 3Ω L
3
4
3
R 3Ω L
SUBWOOFER CENTER FRONT SURROUND
1
2
3
4
5
6
7
8
4
COMMUNICATION
CAMERA
5
6
7
9
FM ANT
75 Ω
LAN
AC IN terminal (> 18)
Speaker terminals (> 13)
Cooling fan
[BTT770] [BTT370] USB port for the Communication Camera
TY-CC10W (optional) (> 34)
LAN port (> 17)
HDMI AV OUT (ARC) terminal (> 15)
[BTT770] [BTT370] HDMI 1 IN (CABLE/SAT) terminal (> 16)
[BTT770] [BTT370] HDMI 2 IN terminal (> 16)
8
9
10
11
12
13
10 11 12
13
AUX
FM radio antenna terminal (> 16)
DIGITAL AUDIO IN terminal (> 14 , 15)
AUX terminal (> 14)
VIDEO OUT terminal (> 14)
[BTT770] Digital transmitter dock for supplied wireless
system (> 17)
[BTT370] Digital transmitter dock for optional wireless
system (> 12)
VQT3D27
7
SC-BTT770_370_270P_eng.book 8 ページ
2010年12月16日 木曜日 午後9時51分
Playable discs/Cards
Type
Logo
examples
Playable contents
( 49)
Type detail
BD-Video
Video
Video
JPEG/MPO (3D still picture)
BD-RE
[BD]
BD-R
Video
DVD-Video
Video
DVD-R
Video
AVCHD
MP3
JPEG/MPO (3D still picture)
[DVD]
DVD-R DL
DVD-RW
Video
AVCHD
+R/+RW/+R DL
—
Music CD
[CD]
Music [CD-DA]
MP3
JPEG/MPO (3D still picture)
CD-R
CD-RW
—
[SD]
Music [CD-DA]
SD Memory Card (8 MB to 2 GB)
SDHC Memory Card (4 GB to 32 GB)
SDXC Memory Card (48 GB, 64 GB)
(Compatible with both mini and micro types)
(as of December 2010)
∫ Discs that cannot be played in this unit
∫ Region management information
Any other disc that is not specifically supported or
previously described.
BD-Video
This unit plays BD-Video marked with labels containing the
region code “A”.
Example:
≥ DVD-RAM
≥ Super Audio CD
≥ Photo CD
≥ DVD-Audio
≥ Video CD and Super Video CD
≥ WMA discs
≥ DivX discs
≥ PAL discs
≥ HD DVD
≥ BD-Video discs recorded at a rate of 50 fields/sec
DVD-Video
This unit plays DVD-Video marked with labels containing the
region number “1” or “ALL”.
Example:
1
VQT3D27
8
MPEG2
AVCHD
JPEG/MPO (3D still picture)
ALL
1
2
4
2010年12月16日 木曜日 午後9時51分
∫ Finalize
∫ SD card
DVD-R/RW/R DL, +R/+RW/+R DL and CD-R/RW recorded by
a recorder, etc. needs to be finalized by the recorder to play on
this unit. Please refer to the recorder’s instructions.
≥ miniSD Cards, microSD Cards, microSDHC
Cards and microSDXC Cards can be used, but
must be used with an adaptor card. These are
usually supplied with such cards, or otherwise
customer provided.
≥ Keep the Memory Card out of reach of children
to prevent swallowing.
≥ To protect the card’s contents, move the record prevention
tab (on the SD card) to “LOCK”.
≥ This unit is compatible with SD Memory Cards that meet SD
Card Specifications FAT12 and FAT16 formats, as well as
SDHC Memory Cards in FAT32 format (Does not support
long file name.) and SDXC Memory Cards in exFAT.
≥ If the SD card is used with incompatible computers or
devices, recorded contents may be erased due to the card
being formatted etc.
≥ Useable memory may be slightly less than the card capacity.
∫ BD-Video
This unit supports high bit rate audio (Dolby Digital Plus, Dolby
TrueHD, DTS-HD High Resolution Audio and DTS-HD Master
Audio) adopted in BD-Video.
∫ Music CD
≥ Operation and sound quality of CDs that do not conform to
CD-DA specifications (copy control CDs, etc.) cannot be
guaranteed.
≥ The digital audio content side of a DualDisc does not meet
the technical specifications of the Compact Disc Digital
Audio (CD-DA) format so playback may not be possible.
∫ 3D
≥ 3D videos and 3D still pictures can be played back when this
unit is connected to a 3D compatible TV using a High Speed
HDMI Cable.
≥ 2D video can be enjoyed as 3D virtually. ( 27)
Unit and media care
∫ Clean this unit with a soft, dry cloth
≥ Never use alcohol, paint thinner or benzine to clean this unit.
≥ Before using chemically treated cloth, carefully read the
instructions that came with the cloth.
Getting started
SC-BTT770_370_270P_eng.book 9 ページ
≥ It may not be possible to play the above media in some cases due to the
type of media, the condition of the recording, the recording method and
how the files were created.
≥ The producers of the disc can control how discs are played. So you may
not always be able to control play as described in this Owner’s Manual.
Read the disc’s instructions carefully.
Using the remote
control
Insert so the poles (+ and –) match those in the remote control.

∫ Clean the lens
≥ Use the lens cleaner (not supplied) to clean the unit’s lens.
∫ Clean discs
DO

DO NOT
R6/LR6, AA
(Alkaline or
manganese batteries)
Wipe with a damp cloth and then wipe dry.
∫ Disc and card handling precautions
≥ Handle discs by the edges to avoid inadvertent scratches or
fingerprints on the disc.
≥ Do not attach labels or stickers to discs.
≥ Do not use record cleaning sprays, benzine, thinner, static
electricity prevention liquids or any other solvent.
≥ Clean any dust, water, or foreign matter from the terminals
on the rear side of the card.
≥ Do not use the following discs:
jDiscs with exposed adhesive from removed stickers or
labels (rented discs etc).
jDiscs that are badly warped or cracked.
jIrregularly shaped discs, such as heart shapes.
∫ To dispose or transfer this unit
The unit may keep the user settings information in the unit. If
you discard this unit either by disposal or transfer, then follow
the procedure to return all the settings to the factory presets to
delete the user settings. ( 43, “To return all settings to the
factory preset”)
≥ The operation history may be recorded in the memory of this
unit.
Point it at the remote control signal sensor on this unit. (
7)
Mishandling of batteries can cause electrolyte leakage which can damage
items the fluid contacts and may cause a fire.
≥ Do not mix old and new batteries or different types at the same time.
≥ Do not heat or expose to flame.
≥ Do not leave the battery(ies) in a car exposed to direct sunlight for a long
period of time with doors and windows closed.
≥ Do not take apart or short circuit.
≥ Do not attempt to recharge alkaline or manganese batteries.
≥ Do not use batteries if the covering has been peeled off.
Remove batteries if the remote control is not going to be used for a long
period of time. Store in a cool, dark place.
CAUTION
≥ Danger of explosion if battery is incorrectly replaced. Replace only with
the type recommended by the manufacturer.
≥ When disposing the batteries, please contact your local authorities or
dealer and ask for the correct method of disposal.
VQT3D27
9
VQT3D27~Body_mst.fm 10 ページ
2011年1月6日 木曜日 午後1時33分
STEP 1 : Preparing the speakers
[BTT770]
∏ 2 Front speakers
∏ 2 Stands (with cables)
(RYK1609E-K: RED)
(RYK1609D-K: WHITE)
[BTT370] [BTT273]
∏ 2 Front speakers
∏ 2 Bases
(RYK1637-K)
[BTT270]
∏ 5 Speaker cables
(REEX1266A: RED)
(REEX1267A: WHITE)
(REEX1268: GREEN)
∏ 2 Bases
(RYK1610-K1)
∏ 4 Screws A
(XTN5i10FFJK)
∏ 3 Speaker cables
(REEX1268: GREEN)
(REEX1269: GRAY)
(REEX1270: BLUE)
∏ 2 Speaker cables
(for SH-FX71)
(REEX1155B-1: GRAY)
(REEX1156B-1: BLUE)
∏ 2 Screws B
(XYN5iJ18FJK)
∏ 5 Speaker cables
(REEX1266A: RED)
(REEX1267A: WHITE)
(REEX1268: GREEN)
(REEX1269: GRAY)
(REEX1270: BLUE)
∏ 2 Screws A
(XTB4i12GFJK)
(REEX1269: GRAY)
(REEX1270: BLUE)
Assembling the speakers
Caution
≥ Do not stand on the base. Be cautious when children are
near.
≥ When carrying speakers, hold the stand and base parts.
Preparation
≥ To prevent damage or scratches, lay down a soft cloth and
perform assembly on it.
≥ For wall mount, refer to page 42.
≥ Keep the screws out of reach of children to prevent
swallowing.
[BTT770]
1
Back of the base
Pull the cable
straight along
the line and
slide into the
groove.
Screw A
2
Insert the wire
fully.
r: White
s: Blue line
Screw B
Leave about 80 mm (3 5/32q)
VQT3D27
10
Tighten
securely.
Push!
Press into the groove.
Tighten securely.
2
1
VQT3D27~Body_mst.fm 11 ページ
2011年1月6日 木曜日 午後1時33分
Thread the speaker cable
through the base.
Insert the wire fully.
r: White
s: Blue line
≥ Use cables with a white connector
and red connector.
Getting started
[BTT370] [BTT273]
Push!
Press into the groove.
Back of the base
Leave about
110 mm (4 11/32q)
Tighten securely.
Pull the cable
straight along the
line and slide into the
groove.
Preparing cables and making connection
1
Use of the speaker cable stickers is
convenient when making cable connections.
e.g. Front speaker (L)
2
Connecting the speaker cables. Insert the
wire fully, taking care not to insert beyond
the wire insulation.
≥ [BTT770] Be sure to use the speaker cables that have a
large connector and short cable when you use the
wireless system.
e.g. Surround speaker
FRONT
Lch



A Speaker cable sticker (supplied)
B Connector
Speaker cable sticker
Color
1 FRONT (L)
WHITE
2 FRONT (R)
RED
3 SURROUND (L)
BLUE
4 SURROUND (R)
GRAY
5 CENTER
GREEN
6 SUBWOOFER
PURPLE
r: White
s: Blue line
Push!
Be sure to match the number on each sticker with the
connector color.
≥ Be careful not to cross (short-circuit) or reverse the polarity of the speaker wires as doing so may damage the speakers.
≥ Don’t use a front speaker as a surround speaker or vice versa. Verify the type of speaker with the label on the rear of the speaker before
connecting the appropriate cable.
≥ To avoid injury by falling or dropping the speaker, place the speaker cables with care not to stumble or hook.
≥ Do not hold the speaker in one hand to avoid injury by dropping the speaker when carrying.
[BTT770] [BTT370] [BTT273]
∫ Preventing the speakers from falling
≥ Consult a qualified housing contractor concerning the appropriate procedure when attaching to a concrete wall or a surface that
may not have strong enough support. Improper attachment may result in damage to the wall or speakers.
≥ Use a string of less than ‰ 2.0 mm (3/32q), which is capable of supporting over 10 kg (22 lbs).
e.g., [BTT770]


A String (not supplied)
Thread from the wall to the speaker and tie tightly.
B Rear of the speaker
C Screw eye (not supplied)
D Wall
E Approx.150 mm (5 29/32q)



VQT3D27
11
SC-BTT770_370_270P_eng.book 12 ページ
2010年12月16日 木曜日 午後9時51分
STEP 2 : Positioning
Caution
≥ The main unit and supplied speakers are to be used only as indicated in this setup. Failure to do so may lead to damage to the
amplifier and/or the speakers, and may result in the risk of fire. Consult a qualified service person if damage has occurred or if
you experience a sudden change in performance.
≥ Do not attempt to attach these speakers to walls using methods other than those described in this manual.
≥ Do not touch the front netted area of the speakers. Hold by the sides.
How you set up your speakers can affect the bass and the sound field.
Setup example
Place the front, center and surround speakers at
approximately the same distance from the seating position.
The angles in the diagram are approximate.
∫ If irregular coloring occurs on your TV,
turn the TV off for about 30 minutes.
If it persists, move the speakers further away from the TV.
≥ Keep your speakers at least 10 mm (13/32z) away from the system for
proper ventilation.


∫ Wireless system
To avoid interference, maintain the following distances
between the wireless system and other electronic devices
that use the same radio frequency (2.4 GHz band).

60°
[BTT770]

Wireless
System
Cordless phone and
other electronic devices:
approx. 2 m (61/2 ft.)
120°



A Center speaker
≥ Put on a rack or shelf not to interfere with the TV's various
sensors (ambient light, etc.). Vibration caused by the speaker
can disrupt the picture if it is placed directly on the TV.
B Front speakers
C Subwoofer
D Surround speakers
≥ Place the speakers at the same height or higher than ear level.
E [BTT770] Wireless System
≥ Place the wireless system within approximately 10 m
(33 ft.) from the main unit, and in a horizontal position
with the top panel faced upward.
≥ To allow for proper ventilation and to maintain good
airflow around the wireless system, position it with at
least 5 cm (2z) of space on all sides.
≥ Do not use the wireless system or the digital transmitter
in a metal cabinet or bookshelf.
[BTT370]
You can enjoy surround speaker
sound wirelessly when you use the
optional Panasonic wireless
accessory (SH-FX71).
For more details, refer to the operating
instructions for the optional wireless system.
≥ When using the SH-FX71 (optional), RMS
TTL power output is changed. ( 48)
≥ Use only supplied speakers
Using other speakers can damage the unit, and sound quality will be
negatively affected.
≥ You can damage your speakers and shorten their useful life if you play
sound at high levels over extended periods.
≥ Positioning speakers in front
It is possible to locate all the speakers in front of the listening position.
However, the optimal surround sound effect may not be obtainable.
≥ Place speakers on flat secure bases.
≥ Placing speakers too close to floors, walls, and corners can result in
excessive bass. Cover walls and windows with thick curtains.
VQT3D27 ≥ For optional wall mount, refer to page 42.
12
Wireless LAN:
approx. 2 m (61/2 ft.)
The wireless system will automatically seek a clear channel if
any of these other devices interfere with its communication.
When this happens, there is a brief interruption in audio
coming from the surround speakers.
This is the normal operation of the product working to assure
the best possible performance of your home theater system.
If the interference persists, try moving the other devices to
another location outside the range of the wireless system or
move the wireless system nearer to the main unit.
[BTT770] [BTT370]
∫ Upgrade your system to 7.1-channel
system
The main unit is designed to enjoy the 7.1ch surround sound. By
connecting 2 units of the Panasonic wireless system SH-FX71
with 4 speakers, more theater-like effect can be available.
Necessary equipment:
[BTT770]
≥ 1 optional wireless system (SH-FX71)
≥ 2 additional speakers
[Impedance: 3 ≠ to 6 ≠, Speaker input power: 100 W (Min)]
[BTT370]
≥ 2 optional wireless systems (SH-FX71)
≥ 2 additional speakers
[Impedance: 3 ≠ to 6 ≠, Speaker input power: 100 W (Min)]
For more details, refer to the operating instructions for the
optional wireless system.
VQT3D27~Body_mst.fm 13 ページ
2011年1月6日 木曜日 午後1時33分
STEP 3: Connections
Getting started
Turn off all equipment before connection and read the appropriate owner’s manual.
Do not connect the AC power supply cord until all other connections are complete.
Speaker cable connection
Connect to the terminals of the same color.
[BTT770]
Connection with the wireless system (SH-FX71)
6 PURPLE
5 GREEN
2 RED
1 WHITE
Subwoofer
Center speaker
Front speaker (Rch)
Front speaker (Lch)



3 BLUE
Surround speaker (Lch)
4 GRAY
Surround speaker (Rch)
≥ Be sure to use the speaker cables that have a large
connector and short cable when you connect the
surround speakers in this connection.



Wireless System
Main unit
SPEAKERS
ENCEINTES
LS / RB LB / RS
3Ω
6
5
3Ω
2
1
R 3Ω L
4
3
R 3Ω L
SUBWOOFER CENTER FRONT SURROUND
SURR
Do not connect the surround speaker cables to the main unit
when using the wireless system.
L
SIDE
SURROUND (3 - 6 )
R
SIDE AMBIOPHONIQUES
Surround selector
The surround selector switch
must be set in the center
position.
Connection with the main unit



  
6 PURPLE
5 GREEN
2 RED
1 WHITE
Main unit
3Ω
6
5
3Ω
2
1
R 3Ω L
4
3
R 3Ω L
Subwoofer
Center speaker
Front speaker (Rch)
Front speaker (Lch)
4 GRAY
Surround speaker (Rch)
3 BLUE
Surround speaker (Lch)
≥ Be sure to use the speaker cables that have a small
connector and long cable when you connect the
surround speakers in this connection.
SUBWOOFER CENTER FRONT SURROUND
[BTT370] [BTT270] [BTT273]



  
Main unit
3Ω
6
5
3Ω
2
1
R 3Ω L
4
3
R 3Ω L
SUBWOOFER CENTER FRONT SURROUND
6 PURPLE
5 GREEN
2 RED
1 WHITE
4 GRAY
3 BLUE
Subwoofer
Center speaker
Front speaker (Rch)
Front speaker (Lch)
Surround speaker (Rch)
Surround speaker (Lch)
[BTT370]
When using the optional wireless system, do not attempt
to connect any extra surround or surround back speakers
to the main unit.
VQT3D27
13
SC-BTT770_370_270P_eng.book 14 ページ
2010年12月17日 金曜日 午後7時44分
Connection to a TV
≥ The basic connection is shown in the included Easy Setting Guide, however, there are more connection examples to optimize
your system setting.
≥ Do not make the video connections through the VCR.
Due to copy guard protection, the picture may not be displayed properly.
≥ Turn off all equipment before connection.
∫ OPTICAL IN
≥ After making the digital audio connection, make settings to suit the type of audio from your digital equipment. (
25)
∫ HDMI
The HDMI connection supports VIERA Link “HDAVI Control” ( 31) when used with a compatible Panasonic TV.
≥ Please use High Speed HDMI Cables that have the HDMI logo (as shown on the back cover). It is recommended that you use
Panasonic’s HDMI cable. When outputting 1080p signal, please use HDMI cables 5.0 meters (16.4 ft.) or less.
Recommended part number (High Speed HDMI Cable):
RP-CDHS15 (1.5 m/4.9 ft.), RP-CDHS30 (3.0 m/9.8 ft.), RP-CDHS50 (5.0 m/16.4 ft.), etc.
≥ Audio will be output through the system's speakers when “Off” is selected in “HDMI Audio Output”. ( 39)
Connection for the standard picture and audio
To enjoy TV audio from this home theater
system’s speakers:
VIDEO IN
TV
AUDIO OUT
AUDIO IN
L
L
R
R
1


2
Connect the TV and the main unit with the
Audio cable (not supplied).
Select “AUX” as a source ( 23).
A Audio cable (not supplied)
B Video cable (not supplied)
AUX
AUX
VIDEO OUT
Connection for the better audio
TV
To enjoy TV audio from this home theater
system’s speakers:
VIDEO IN
OPTICAL
OUT
AUDIO IN
L
1
R


2
Connect the TV and the main unit with the
Optical digital audio cable (not supplied).
Select “DIGITAL IN” or “D-IN” as a source
( 23).
A Optical digital audio cable (not supplied)
B Video cable (not supplied)
OPTICAL
VQT3D27
14
VIDEO OUT
VQT3D27~Body_mst.fm 15 ページ
2011年1月6日 木曜日 午後1時35分
∫ When the HDMI terminal on the TV is labeled “HDMI (ARC)”
Getting started
Connection for the best picture and audio
≥ When connecting to a TV using an HDMI cable, check the HDMI terminal on the TV. If the HDMI terminal is labeled
“HDMI (ARC)”, you can connect the unit simply with a single HDMI cable.
≥ It is possible to playback 3D videos and 3D still pictures by connecting this unit with a 3D compatible TV.
≥ For details, refer to the operating instructions of your TV.
What is ARC?
ARC is an abbreviation of Audio Return Channel, also known
as HDMI ARC. It refers to one of the HDMI functions. When
you connect the unit to the terminal labeled “HDMI (ARC)”, the
optical digital audio cable that is usually required in order to
listen to sound from TV is no longer required, and TV pictures
and sound can be enjoyed with a single HDMI cable.
TV
HDMI
(ARC)
To enjoy TV audio from this home theater
system’s speakers:

Select “ARC” as a source (> 23).
A HDMI cable
[BTT770] [BTT370] [BTT270] : not supplied
[BTT273] : supplied
HDMI AV OUT (ARC)
∫ When the HDMI terminal on the TV is not labeled “HDMI (ARC)”
To enjoy TV audio from this home theater
system’s speakers:
TV

HDMI
1
OPTICAL
OUT
2
Connect the TV and the main unit with the
Optical digital audio cable (not supplied).
Select “DIGITAL IN” or “D-IN” as a source
(> 23).
A HDMI cable
[BTT770] [BTT370] [BTT270] : not supplied
[BTT273] : supplied

B Optical digital audio cable (not supplied)
HDMI AV OUT
OPTICAL
VQT3D27
15
SC-BTT770_370_270P_eng.book 16 ページ
2010年12月16日 木曜日 午後9時51分
Connection with Set Top Box, etc.
∫
[BTT770] [BTT370]
When the connecting devices have an HDMI terminal
e.g.,

TV
AV IN
(ARC)

AV OUT
AV OUT

≥ Make sure that the HDMI cable connection is made to enjoy
the videos from the Set Top Box, etc. Futhermore, select
“HDMI Input1” or “HDMI Input2” as a source.
HDMI Standby Pass-Through (

39)
Even if this unit is in standby mode, a device connected with
this unit can output videos and sound to the TV.
Moreover, you can switch the HDMI input terminal by pressing
[EXT-IN] on the remote control.
≥ Sound will not be output from this unit's speakers.

HDMI AV OUT
(ARC)
A HDMI cable (not supplied)
B Set Top Box (Cable/Satellite), etc.
C Other devices (Video game, etc.)
HDMI IN 2
HDMI IN 1(CABLE/SAT)
∫ When the connecting devices do not have an HDMI terminal
e.g.,


TV
OPTICAL
OUT
To enjoy TV audio from this home theater
system’s speakers:
1
2

Connect the STB and the main unit with the
Optical digital audio cable (not supplied).
Select “DIGITAL IN” or “D-IN” as a source
( 23).
A Refer to the operating instructions of the
respective devices for the optimal connections.
B Optical digital audio cable (not supplied)
C Set Top Box (Cable/Satellite), etc.
OPTICAL
Radio antenna connection
∫ Using an indoor antenna
∫ Using an outdoor antenna
Use outdoor antenna if FM radio reception is poor.

Main unit
e.g.,


FM ANT
75Ω


Main unit
FM ANT
75Ω
A FM indoor antenna (supplied)
B Adhesive tape
Affix this end of the antenna where reception is best.
VQT3D27
16
A FM outdoor antenna [Using a TV antenna (not
supplied)]
The antenna should be installed by a competent
technician.
B 75 ≠ coaxial cable (not supplied)
C Antenna plug (not supplied)
SC-BTT770_370_270P_eng.book 17 ページ
Digital transmitter connection
Do not insert or remove while the home
theater unit is on.
DO
Getting started
[BTT770]
2010年12月16日 木曜日 午後9時51分
DO NOT
Make sure that the digital transmitter is fully inserted.
Insert fully until you
hear a click.
If the digital transmitter is not fully inserted, the sound may
not be available from the surround speakers.
Connection to a broadband network
The following services can be used when this unit is connected to broadband.
≥ Firmware can be updated ( 22)
≥ You can enjoy BD-Live ( 26)
≥ You can enjoy VIERA CAST ( 34)
∫ LAN cable connection
For details about connection method, refer to the instructions
supplied with the connected equipment.
∫ Wireless LAN connection

LAN




A LAN Cable (not supplied)
B Broadband router, etc.
C Modem (Broadband) *Provided by ISP
≥ Use category 5 or above straight LAN cables (STP) when
connecting to peripheral devices.
≥ Inserting any cable other than a LAN cable in the LAN
terminal can damage the unit.



A Main unit (Wireless LAN is built in.)
B Wireless router, etc.
C LAN Cable (not supplied)
D Modem (Broadband) *Provided by ISP
≥ For up to date compatibility information on your Wireless
router refer to
http://panasonic.jp/support/global/cs/
(This site is in English only.)
≥ The unit is not compatible with public wireless LAN
services provided in airports, stations, cafes etc.
For additional information about this unit refer to
http://www.panasonic.com/consumer/support (For U.S.A.)
Precautions of Wireless LAN connection
The following limits are in place regarding the usage of this unit. You must be aware of these limits before using this unit.
Panasonic will in no way be responsible for any incidental damage which may arise due to a failure to obey these limits, or to any condition of use or disuse of this unit.
≥ Data transmitted and received over radio waves may be intercepted and monitored.
≥ This unit contains delicate electronic components.
Please use this unit in the manner in which it was intended and follow the following points:
– Do not expose this unit to high temperatures or direct sunlight.
– Do not bend, or subject this unit to strong impacts.
– Keep this unit away from moisture.
– Do not disassemble or alter this unit in any way.
VQT3D27
17
VQT3D27~Body_mst.fm 18 ページ
2011年1月6日 木曜日 午後1時36分
STEP 4: AC power supply cord connection
Connect only after all other connections are complete.
AC IN

Main unit
[BTT770]
Wireless System
≥ AC power supply cord
with a ferrite core is for the
wireless system. Do not
use any other AC power
supply cord except the
supplied one.



A AC power supply cord (supplied)
B To a household AC outlet
A AC power supply cord (supplied)
B To a household AC outlet
Main unit
This unit consumes a small amount of AC power, even when it is turned off.
[BTT770] [BTT370] : approx. 0.05 W*, [BTT270] [BTT273]: approx. 0.4 W*
* When the “Quick Start” setting is “Off”
In the interest of power conservation, if you will not be using this unit for a long time, unplug it from the household AC outlet.
Wireless system [BTT770]: approx. 0.2 W
Install this unit so that the power cord can be unplugged from the socket outlet immediately if any problem occurs.
STEP 5:
[BTT770]
Preparing the wireless system
Turn on the wireless system after all connections are complete.
Press [POWER C I, B Í] on the wireless system.
POWER
Wireless System
VQT3D27
18
WIRELESS LINK
Unit on/off button [POWER C I, B Í]
C I:
The wireless system is on.
B Í:
The wireless system is off.
WIRELESS LINK indicator
Red:
The wireless system is on and the wireless link is deactivated.
Green : The wireless system is on and the wireless link is activated.
(“WIRELESS SPEAKERS LINKED” is also displayed on the main unit’s
display by pressing and holding [STATUS] on the remote control.)
VQT3D27~Body_mst.fm 19 ページ
2010年12月27日 月曜日 午後6時17分
The Easy setup assists you to make necessary
settings.
1
Press [Í].
Setup screen appears.
If this unit is connected to a Panasonic TV (VIERA)
supporting HDAVI Control 2 or later via an HDMI cable,
then setting information on the TV such as “On-screen
Language” is acquired by this unit.
Follow the on-screen prompts to make basic settings for the
system.
2
Getting started
STEP 6: Easy setup
Follow the on-screen instructions and
make the settings with [3, 4, 2, 1] and
press [OK].
Language
Select the language used on menu screen.
TV Aspect
Select the aspect to suit your TV and preference.
チ
[BTT770] [BTT370]
Wireless System
If a digital transmitter is inserted,
it is required to specify the current settings.
OK
Speakers position
Specify the positioning of the surround speakers.
Speaker check
Check if the connection to each speaker is valid.
Speaker Output
Make surround sound setting for speaker output.
Preparation
Turn on your TV and select the appropriate video input mode
(e.g., VIDEO 1, AV 1, HDMI, etc.) to suit the connections to this
unit.
Cinema Surround Plus
(Effective when the surround layout is selected in
“Speakers position”.)
The function creates the sound of virtual speakers to
enhance the realistic surround feeling as if the sound
comes from all directions.
[BTT770] [BTT370]
≥ Confirm the digital transmitter connection. (> 17)
TV Audio
Select the audio input connection from your TV,
[item with “(TV)”].
Quick Start
Speed of startup from power off is increased.
[BTT770] [BTT370]
HDMI Standby Pass-Through
Even if this unit is in standby mode, a device
connected with this unit can output videos and sound
to the TV. (> 16, “When the connecting devices have
an HDMI terminal”)
3
Press [OK] several times to finish the “Easy
setup”.
After completing “Easy setup”, you can perform “Network Easy
Setting”.
≥ You can perform this setup anytime by selecting “Easy setup” in the Setup
menu. (> 40)
VQT3D27
19
SC-BTT770_370_270P_eng.book 20 ページ
2010年12月16日 木曜日 午後9時51分
Network Easy Setting
The configuration of your network is about to begin. If you
failed to make the settings, refer to page 21
Wired connection
∫ “Search for wireless network”
The available wireless networks will be displayed.
1 Select your network name and press [OK].
≥ If your network name is not displayed search again by
pressing the [R] button on the remote control. Stealth
SSID will not be displayed, in this case enter manually.
Wireless Settings
Select a wireless network for connection.
Select “Wired” and press [OK].
Network name (SSID)
Network Easy Setting
Select a connection mode.
Current setting
: Wired
LAN cable connection:
Connect a LAN cable to the unit and select "Wired."
Reception
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
Wireless LAN connection:
Select "Wireless."
OK
R Search again
RETURN
SUB
MENU
G
B
Y
Wired
Wireless
OK
RETURN
Follow the on-screen instructions to make your connection
settings.
≥ When you experience problems ( 21)
When your wireless network is encrypted
2 Press [OK] to select “Encryption Key”.
Wireless Settings
Enter the encryption key of the wireless network.
Encryption Key
Wireless connection
Set
Preparation
≥ Obtain your network name ( 21, SSID).
≥ If your wireless connection is encrypted please be sure
that you know your encryption key.
1
2
3 Enter your encryption key.
Encryption Key
_
Select “Wireless” and press [OK].
Select “Search for wireless network” or
“WPS (PUSH button method)” and press
[OK] then follow the on-screen instructions
and make the settings.
1
2
3
4
5
6
7
8
9
0
Delete
Finish
OK
RETURN
1 2 3 4 5
a
B C
d
E F
g
H I
j
K L
m
N O
Q R S p
A
D
G
J
M
P
T
6
b
e
h
k
n
q
7
c
f
i
l
o
r
8 9 0
+ - *
%
&
@
_
)
} ~
/
#
<
[
s
=
$
>
]
(
t u v {
U V
W X Y Z w x y z
. , ? ! “ ’ : ;
\
0 - 9
I
` ^
Space
Wireless Settings
Select a connection method.
Please refer to the operating instructions of your wireless
access point about connection methods.
Search for wireless network
WPS (PUSH button method)
∫ “WPS (PUSH button method)”
If you are using a Wireless router that supports WPS (Wi-Fi
Protected Setup), you can easily perform the settings.
To enter SSID manually
If your SSID is not displayed in step 1, follow these steps.
1 To display SSID input screen :
Press [HOME] select “Others”
[OK] [OK] (“Setup”)
select “Network” [OK] select “Network Settings”
[OK] select “Wireless Settings”
[OK]
select
“Connection Setting” [OK] select “Manual setting”
[OK]
2 Press [OK] to select “SSID” and enter your SSID.
Wireless Settings
Enter your network name (SSID) to connect.
SSID
Set
≥ If your wireless network is encrypted, go to step 2.
VQT3D27
20
2010年12月16日 木曜日 午後9時51分
When you experience problems
with settings
Network Easy Setting (Internet Connection Check)
Network Easy Setting (Internet Connection Check)
Complete.
- Connection to the Internet
: Fail(Error code: B019)
Wireless Setting
Failed the connection test.
Cannot find the server.(Error code: B019)
Please refer to the owner's manual for the cause of
the error and the solution for it.
Press [OK].
Wireless Settings
Failed to complete.
Getting started
SC-BTT770_370_270P_eng.book 21 ページ
A conflict with another device occurred.
Do you want to configure wireless network connection
setting again ?
OK
Yes
Display
No
OK
Display
Check the following
A conflict with another ≥ Please wait a few moments, and
device occurred.
then try again.
A time out error
occurred.
An authentication
error or a time out
error occurred.
≥ Setting of the Wireless router for
MAC Address etc.
≥ The signal may be weak.
≥ The SSID ( right) and the
encryption key of the Wireless
router.
≥ Please wait a few moments, and
then try again.
A device error
occurred.
≥ Contact our Customer Service
Center or your nearest dealer.
Network Easy Setting (Home Network Connection Check)
Network Easy Setting (Home Network Connection Check)
Complete.
1. LAN cable connection
2. IP address setting
3. Connection to gateway
: Fail
: Fail
: Fail
LAN cable is not connected.
Please check the connection.
Select “Yes” and press [OK] to check network
connection again. Select “No” and press [OK]
to finish Network Easy Setting.
Yes
No
1. LAN cable connection or
Wireless setting
Check the
following
:Fail
2. IP address setting
:Fail
3. Connection to gateway
:Fail
1. LAN cable connection or
Wireless setting
:Pass
2. IP address setting
:Fail
3. Connection to gateway
:Fail
1. LAN cable connection or
Wireless setting
:Pass
2. IP address setting
:Pass
3. Connection to gateway
:Fail
≥ “Primary DNS” and “Secondary
DNS” Settings of “IP Address /
DNS Settings” ( 40)
Failed to connect to the
server.
(Error code: B020)
≥ The server may be busy or the
service may have been
suspended. Please wait a few
moments, and then try again.
≥ Settings of “Proxy Server
Settings” ( 40) and the router.
≥ Refer to the operating instructions of the hub or router.
≥ WPS (Wi-Fi Protected Setup) is a standard that facilitates settings relating
to the connection and security of wireless LAN devices. To see whether
your Wireless router supports WPS, check the Wireless router operating
instructions.
≥ You can perform this setup anytime by selecting “Network Easy Setting” in
the Setup menu. ( 40)
≥ You can redo these settings individually using “Network Settings”. ( 40)
≥ Do not use this unit to connect to any wireless network for which you do not
have usage rights.
During automatic searches in a wireless network environment, wireless
networks (SSID*) for which you do not have usage rights may be
displayed; however, using these networks may be regarded as illegal
access.
≥ After performing network settings on this unit, the settings (encryption level,
etc.) of the Wireless router might change. When you have trouble getting
online on your PC, perform the network settings on your PC in accordance
with the settings of Wireless router.
≥ Please be aware that connecting to a network without encryption may
result in the content of the communication being illegitimately viewed by a
third party, or the leaking of data such as personal or secret information.
* An SSID (Service Set IDentification) is a name used by wireless LAN to
identify a particular network. Transmission is possible if the SSID matches
for both devices.
OK
Display
Check the following
Cannot find the server.
(Error code: B019)
≥ Connection of
the LAN
cables ( 17)
≥ Connection
and settings of
the hub and
router
≥ Settings of “IP
Address /
DNS Settings”
( 40)
Reprogramming the remote
control
If you have more than one Panasonic player/recorder and the
remote control operates both products at once, you will
need to change the remote control code on one product to
prevent this occurrence. ( 40, “Remote Control Code”)
VQT3D27
21
SC-BTT770_370_270P_eng.book 22 ページ
2010年12月16日 木曜日 午後9時51分
Firmware updates
Occasionally, Panasonic may release updated firmware for this
unit that may add or improve the way a feature operates.
These updates are available free of charge.
Inserting or removing
media
This unit is capable of checking the firmware automatically
when connected to the Internet via a broadband connection.
When a new firmware version is available, the following
message is displayed.
OPEN/CLOSE
New firmware is available.
Please update firmware in Setup.
VOL
SD CARD
To update the firmware
Press [HOME] select “Others” [OK] [OK] (“Setup”)
select “Others”
[OK]
select “Firmware Update”
[OK]
select “Update Now”
[OK]
DO NOT DISCONNECT the unit from the AC power or perform
any operation while the update takes place.
After the firmware is installed, “FINISH” will be displayed on the
unit’s display. Unit will restart and the following screen will be
displayed.
The firmware was updated.
Current Version: x.xx
≥ When inserting a media item, ensure that it is facing the right
way up.
≥ While the reading indicator is displayed, do not turn off the
unit or remove the media. Such action may result in loss of
the media’s contents.
≥ When removing the SD card, press on the center of the card
and pull it straight out.
OK
RETURN
≥ If downloading on this unit fails or this unit is not connected to the
Internet, then you can download the latest firmware from the following
website and burn it to a CD-R to update the firmware.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
To show the firmware version on this unit. ( 40, “System Information”)
≥ Downloading will require several minutes. It may take longer or may
not work properly depending on the connection environment.
≥ If you do not want to check for the latest firmware version, set “Automatic
Update Check” to “Off”. ( 40)
∫ Selecting the source by the remote
control
Button
DISC/SD
RADIO/EXT-IN
iPod
Source
Select disc drive or SD card drive
BD/DVD or SD card (SD) ( 25)
Select iPod/iPhone, FM tuner or external
audio as the source
iPod (IPOD) ( 32)
FM Radio (FM) ( 29)
To enjoy sound from the TV ( 30)
AUX*1
ARC*1
DIGITAL IN*1(D-IN)
To enjoy sound from other devices
( 30)
DIGITAL IN*2(D-IN)
[BTT770] [BTT370]
HDMI IN1/HDMI IN2 ( 16)
≥ Items to be displayed may vary with the media.
≥ When the selector is switched, it may take time to playback the selected
video and/or audio.
*1
*2
VQT3D27
22
“(TV)” is displayed next to items set for TV AUDIO input.
“(CABLE/SATELLITE)” is displayed next to DIGITAL IN when set for
CABLE/SATELLITE AUDIO input.
2010年12月17日 金曜日 午後7時44分
HOME menu
Videos/
Photos/
Music
SD card
Turn on the television and select the appropriate video input on
the television.
Internet
Content
Displays the Home screen of VIERA CAST
( 34)
1
2
iPod
All
Major functions of this unit can be operated from the HOME
menu.
Disc
Preparation
Press [Í] to turn on the unit.
Music
Press [3, 4, 2, 1] to select the item and
press [OK].
HOME
Home theater
OK
EXT IN
Internet
Content
FM Radio
Photos
Videos
Music
Sound
iPod
Play back the contents.
( 25, 28, 29)
≥ When multiple contents are
recorded, select the types
of contents or the title.
(
Getting started
SC-BTT770_370_270P_eng.book 23 ページ
32)
Videos
FM
Radio
To enjoy the FM radio (
EXT IN
AUX*1
When using an Audio cable
ARC*1
When using an HDMI cable
(Available when using an
ARC compatible TV)
DIGITAL IN*1, 2
When using an Optical digital
audio cable
Others
≥ When a media is inserted, contents selection screen for
that media is displayed.
≥ If there are any other items, repeat this step.
≥ To return to HOME menu, select “HOME” or press
[RETURN] several times.
[BTT770]
[BTT370]
HDMI IN1
HDMI IN2
29)
When connecting to HDMI IN1
and/or HDMI IN2 terminal
( 16)
Sound
Select sound quality (equalizer). (
Others
Setup
(
37)
SD Card
Management
(
26)
Wallpaper
24)
Changes the screen
background of the HOME
menu.
To show the HOME menu
Press [HOME].
≥ Items to be displayed may vary with the media.
≥ When the selector is switched, it may take time to playback the selected
video and/or audio.
*1
*2
“(TV)” is displayed next to items set for TV AUDIO input.
“(CABLE/SATELLITE)” is displayed next to DIGITAL IN when set for
CABLE/SATELLITE AUDIO input.
VQT3D27
23
SC-BTT770_370_270P_eng.book 24 ページ
2010年12月16日 木曜日 午後9時51分
Enjoying sound effects
from all speakers
Enjoying surround sound
effects
1
Press [SURROUND] several times to select
the effect.
STANDARD
Sound is output as it was recorded/encoded.
Speaker output varies depending on the source.
MULTI-CHANNEL
You can enjoy sound from the front speakers, as well as
the surround even when playing a 2-channel sound or
non-surround sound.
MANUAL
2
≥ The selected effect will only be displayed on the main
unit.
While “MANUAL” is displayed, press
[2, 1] and select the desired effect.
DOLBY PRO LOGIC II MOVIE
Suitable for movie software, or the one recorded in Dolby
Surround.
DOLBY PRO LOGIC II MUSIC
Adds 5.1-channel effects to stereo sources.
7.1CH VIRTUAL SURROUND
You can enjoy 6.1/7.1-channel surround-like effect using
5.1-channel speakers.
SUPER SURROUND
You can enjoy sound from all speakers with stereo
sources.
2CH STEREO
You can play any source in stereo. Sound will be output to
the front speakers and the subwoofer only.
≥ When you set to “7.1CH VIRTUAL SURROUND“,
“SUPER SURROUND“ and “2CH STEREO“, “Cinema
Surround Plus“ ( 36) is not activated.
∫ Adjusting speaker level during play
1 Press and hold [jCH SELECT] to activate the speaker
setting mode.
2 Press [jCH SELECT] several times to select the speaker.
Each time you press the button:
L R C RSRB* LB*LS SW

VQT3D27
24
* When the optional surround back speakers are connected.
L R: Front speaker
(left and right: only the balance is adjustable.)
≥Press [2, 1] to adjust the balance of the front
speakers.
C: Center speaker
RS: Surround speaker (right)
RB*: Surround back speaker (right)
LB*: Surround back speaker (left)
LS: Surround speaker (left)
SW: Subwoofer
≥ The channels not included in the playing audio will not
be displayed (subwoofer is displayed even if it is not
included).
3 Press [3] (increase) or [4] (decrease) to adjust the
speaker level for each speaker.
s6 dB to r6 dB
∫ Changing the sound modes
1 Press [SOUND] several times to select the mode.
≥ The selected mode will only be displayed on the main
unit.
2 While the selected mode is displayed
Press [2, 1] and select the desired setting.
EQUALIZER
You can select sound quality settings.
FLAT
Cancel (no effect is added).
HEAVY
Adds punch to rock.
CLEAR
Clarifies higher sounds.
SOFT
For background music.
SUBWOOFER LEVEL
You can adjust the amount of bass.
1 (Weakest effect) to 4 (Strongest effect)
≥The setting you make is retained, and recalled every
time you play the same type of source.
H.BASS
You can enhance low-frequency sound so that heavy
bass sound can be heard clearly, even if the acoustics of
your room are not optimal.
≥The setting you make is retained, and recalled every
time you play from the same type of source.
CENTER FOCUS
(Effective when playing audio containing center
channel sound.)
You can make the sound of the center speaker seem like
it is coming from within the TV.
WHISPER-MODE SURROUND
You can enhance the surround effect for low volume
sound. (Convenient for late night viewing.)
≥ The sound effects/modes may not be available or have no effect with some
sources.
≥ You may experience a reduction in sound quality when these sound
effects/modes are used with some sources. If this occurs, turn the sound
effects/modes off.
SC-BTT770_370_270P_eng.book 25 ページ
2010年12月16日 木曜日 午後9時51分
Playing video contents
Playback
[BD] [DVD] [CD] [SD]
Search
1
While playing, press [SEARCH6] or
[SEARCH5].
If the menu is displayed, press [OK] or [3, 4, 2, 1] to
select the item. ( 23)
2
Press [3, 4] to select the title and press
[OK].
When a message screen is displayed while playing back
3D compatible video software, play back in accordance
with the instructions.
≥ Music and MP3: The speed is fixed to a single step.
Slow-motion
While paused, press [SEARCH6] or
[SEARCH5].
≥ BD-Video and AVCHD: Forward direction [SEARCH5]
only.
The speed increases up to 5 steps.
≥ Press [1 PLAY] to revert to normal playback speed.
∫ To show menus
You can show Top Menu, DIRECT NAVIGATOR or Pop-up Menu.
Press [POP-UP MENU, TOP MENU].
≥ Press [3, 4, 2, 1] to select the item and press [OK].
∫ To show the status messages
e.g. BD-Video
T: Title, C: Chapter, PL: Playlist
BD-Video
0:05.14
0:20.52
Current position
Skip to the title, chapter or track you want to play.
≥ Each press increases the number of skips.
Frame-by-frame
While paused, press [2] (2;) or [1] (;1).
Elapsed time in the title
C1
Skip
While playing or paused, press [:] or [9].
While playing, press [STATUS].
The status messages give you information about what is currently
being played. Each time you press [STATUS], the display
information may change or will disappear from the screen.
 T1
Playback
Insert the media.
Getting started
Search/Slow-motion
Play
≥ Press and hold to change in succession forward or
backward.
≥ Press [1 PLAY] to revert to normal playback speed.
≥ BD-Video and AVCHD: Forward direction [1] (;1) only.
Total time
≥ DISCS CONTINUE TO ROTATE WHILE MENUS ARE DISPLAYED. Press
[∫STOP] when you finish to preserve the unit’s motor and your television
screen.
≥ Depending on media and contents, the display may change or may not
appear.
≥ It is not possible to playback AVCHD and MPEG2 video which have been
dragged and dropped, copied and pasted to the media.
Other operations during play
These functions may not work depending on the media and its
contents.
Stop
Changing audio
1
Press and hold [jAUDIO] to activate the
audio setting mode.
2
Press [jAUDIO] several times to select the
audio.
You can change the audio channel number or soundtrack
language, etc.
∫ Selecting the type of audio from the
DIGITAL AUDIO IN terminal
Select to suit the type of audio from the DIGITAL IN terminal on
the main unit.
Press [∫STOP].
1 Press [EXT-IN] several times to select “DIGITAL IN” (D-IN).
The stopped position is memorized.
2 Press and hold [jAUDIO] to activate to select the type.
3 Press [jAUDIO] several times to select the type.
MAIN
SAP*
MAINrSAP* (stereo audio)
* “SAP” = Secondary Audio Program
(Only works with Dolby Dual Mono)
≥ “MAIN” or “SAP” is not available if “On” is selected in
“PCM-FIX” of “DIGITAL IN”. ( 38)
Resume play function
Press [1 PLAY] to restart from this position.
≥ The position is cleared if the tray is opened or you press
[∫STOP] several times to display “STOP” on the unit’s display.
≥ On BD-Video discs including BD-J, the resume play
function does not work.
Pause
Press [;PAUSE].
≥ Press [;PAUSE] again or [1 PLAY] to restart play.
≥ Audio that is input through the DIGITAL AUDIO IN or AUX terminals are not
output from the HDMI AV OUT terminal.
VQT3D27
25
SC-BTT770_370_270P_eng.book 26 ページ
2010年12月16日 木曜日 午後9時51分
Useful functions
1
2
Press [SUB MENU].
Select an item and press [OK].
While DIRECT NAVIGATOR screen is displayed
Properties
To display the titles properties (recording
date, etc.)
View
Chapters
To select the chapter
View
Playlists
To play playlists
View Titles
To select the title.
∫ Deleting data/Formatting SD cards
If you no longer need data recorded on the SD card, you can
delete data with the following operation.
Insert an SD card.
Press [HOME].
Press [3, 4, 2, 1] to select “Others” and press [OK].
Press [1] to select “SD Card Management” and press
[OK].
5 Press [3, 4] to select “BD-Video Data Erase” or “Format
SD Card” and press [OK].
1
2
3
4
SD Card Management
SD card
No. of Files 6
Free space 300 MB
BD-Video Data Erase
Format SD Card
While playing
Screen
Aspect
When black bars are shown at the top,
bottom, left, and right sides of the screen,
you can enlarge the image to fill the screen.
Top Menu
To display Top Menu.
Pop-up
Menu
To display Pop-up Menu.
Menu
To display Menu.
3D Settings
2D video can be virtually output as 3D, or
output effect of the 3D video can be setup.
( 27)
≥ Depending on the played contents if you perform “Screen
Aspect”, there may be no effect.
≥ When “TV Aspect” ( 39) is set to “4:3” or “4:3 Letterbox”,
the “Zoom” effect in “Screen Aspect” is disabled.
OK
RETURN
6 Press [2, 1] to select “Yes” and press [OK].
7 Press [2, 1] to select “Start” and press [OK].
Playing picture-in-picture
To turn on/off secondary video and audio
[DISPLAY] select “Disc” [1] select
“Signal Type” [OK] set “Video” and
“Soundtrack” in “Secondary Video” to “On” or
“Off”

≥ Depending on the media and contents, displayed items are different.

Enjoying BD-Live or
picture-in-picture in BD-Video
Enjoying BD-Live discs with
Internet
BD-Live allows you to enjoy more functions such as subtitles,
exclusive images and online games by connecting this unit to
the Internet. Since most of the BD-Live compatible discs are
played back using the BD-Live function, additional contents
are required to be downloaded into the external memory (local
storage).
≥ This unit is using an SD card as a local storage device.
BD-Live function cannot be used when there is no SD card
inserted.
VQT3D27
26
1
Perform network connection and settings.
( 17, 20)
2
Insert an SD card with 1 GB or more free
space.
3
Insert the disc.
Format this SD Card.
A Secondary video
B Primary video
≥ The usable functions and the operating method may vary with each disc,
please refer to the instructions on the disc and/or visit their website.
≥ Some BD-Live content available on the Blu-ray discs may require an
Internet account to be created in order to access the BD-Live content.
Follow the screen display or instruction manual of the disc for information
on acquiring an account.
≥ To use the BD-Live functions, it is recommended that you format the card
on this unit. If the SD card you use is formatted, all data on the card will be
erased. It cannot be recovered.
≥ “BD-Live Internet Access” may need to be changed for certain discs
( 37).
≥ When discs supporting BD-Live are played back, the player or disc IDs
may be sent to the content provider via the Internet.
≥ During search/slow-motion or frame-by-frame, only the primary video is
displayed.
≥ When “BD-Video Secondary Audio” in “Digital Audio Output” is set to “Off”,
secondary audio will not be played ( 38).
2010年12月16日 木曜日 午後9時51分
Enjoying 3D video
You can enjoy powerful 3D videos with realistic sensations by
connecting this unit with a High Speed HDMI Cable to a 3D
compatible TV.
Useful functions
1
While playing,
Press [SUB MENU].
2
Press [3, 4] to select “3D Settings” and
press [OK].
3
Select an item, then press [OK].
Signal
Format
Original
Keep original picture
format.
Side by side
3D picture format
comprising of left and right
screens.
2D to 3D
Converts 2D pictures to 3D
effect.
Normal
Playback pictures with
normal 3D effects.
Soft
You can enjoy 3D pictures
with a feeling of
broadness, holding back
the depth perception.
Manual
Settings
Set 3D effect manually.
The illustration is an image.
Preparation
Connect 3D compatible TV to an HDMI AV OUT terminal of
this unit using a High Speed HDMI Cable and select HDMI
video input mode on the TV. ( 14, 15)
≥ Perform the necessary preparations for the TV.
3D
Picture
Mode
Method of playback is the same as normal disc playback.
( 25)
≥ Playback following the instructions displayed on the screen.
Distance
Set the amount of depth
perception.
Screen Type
Selects how the screen
appears during 3D
playback (flat or round).
Frame Width
Set the amount of
feathering at the edge of
screen.
Frame Color
Set the color of feathering
at the edge of screen.
3D settings
Perform the following settings as necessary.
3D BD-Video
Playback
It is also possible to play back 3D discs
in 2D (conventional video). ( 37)
3D Type
If 3D video cannot be played back in
3D, change the settings as required by
the connected TV format. ( 39)
≥ Change the settings for 3D on the TV
also when “Checker board” or “Side
by side” is selected.
3D Playback
Precautions
Hide the 3D viewing warning screen.
( 39)
Pop-Out Level
Adjust the pop-up position for the
Playback menu or message screen etc.
( 36)
Playback
SC-BTT770_370_270P_eng.book 27 ページ
≥ Depending on the contents, displayed items are different.
≥ Please refrain from viewing 3D images if you do not feel well or are
experiencing visual fatigue.
In the event that you experience dizziness, nausea, or other discomfort
while viewing 3D images, discontinue use and rest your eyes.
≥ Depending on the connected TV, the video being played back might switch
to 2D video due to changes in resolution etc. Check the 3D setting on the
TV.
≥ 3D images may not output as settings of “HDMI Resolution” and “24p
Output”. ( 39)
VQT3D27
27
SC-BTT770_370_270P_eng.book 28 ページ
2010年12月24日 金曜日 午前10時57分
Playing still pictures
[BD] [DVD] [CD] [SD]
(BD-RE, DVD-R/R DL, CD-R/RW, SD Card)
In order to play back 3D still pictures (MPO), this unit should be
connected to a Full HD 3D compatible TV via an HDMI
terminal.
1
Useful functions
1
2
Press [SUB MENU].
Select an item, then press [OK].
While Photo View screen is displayed
Slideshow
Insert the media.
If the menu is displayed, press [OK] or [3, 4, 2, 1] to
select the item. ( 23)
2
Press [3, 4] to select the folder and press
[OK].
“3D View” : 3D still pictures (MPO) are sorted here. To play
back in 3D, select from “3D View”. (Still pictures in “2D
View” are played back in 2D)
Photo View
SD card
2D View
3D View
Folder Name
Photos
XXXXXXXX
42
XXXX
Start Slideshow
You can display still pictures one by one at
a constant interval.
Display Interval
Change the display interval.
Transition Effect
Set display method.
Repeat Play
Repeat slideshow.
Random Soundtrack
Background music is played in random
order.
Soundtrack
An MP3 on the iPod/iPhone or a music CD
can be played back during the slideshow of
JPEG on the SD card.
105
SUB
MENU
OK
RETURN
R
G Slideshow
XXXXXXXX
58
XXXXXXXX
77
XXXXXXXX
48
XXXXXXXX
5
Page Up
B Select
Page Down
Page01/02
Y
To select folders or still pictures that are played on
slideshow.
3
Press [3, 4, 2, 1] to select the still
picture and press [OK].
Press [2, 1] to display the previous or next still picture.
To exit the screen
Press [RETURN].
∫ To show the still picture properties
While playing
Start
Slideshow
Start the slideshow.
Screen
Aspect
Switch the screen mode.
Status
Show the still picture properties.
Rotate
Right
Rotate the still picture.
Rotate Left
Wallpaper
Set the still picture to the wallpaper of
HOME screen. ( 23)
Pop-Out
Level
Pop-up position for the Playback menu or
message screen etc. can be adjusted
during 3D playback.
While playing, press [STATUS] once or twice.
Date
11/12/2007
Size
500 x 375
Manufacturer
Equipment
To exit the screen
Press [STATUS].
VQT3D27
28
1 / 26
≥ Depending on the condition of the unit and media contents, displayed items
are different.
≥ When viewing a 3D still picture, some functions may not work.
≥ When a still picture with large number of pixels is played, the display
interval may become longer. Even if the setting is changed, the display
interval may not become shorter.
≥ When both a music CD and an iPod/iPhone is inserted to this unit, the
iPod/iPhone has a priority to be played back as background music.
≥ Still pictures displayed as “
” cannot be played back with this unit.
2010年12月16日 木曜日 午後9時51分
Playing music
Listening to the Radio
Radio
[DVD] [CD]
(DVD-R/R DL, music CD, CD-R/RW)
Insert the media.
If the menu is displayed, press [OK] or [3, 4, 2, 1] to
select the item. ( 23)
2
Press [3, 4] to select the track and press
[OK].
DIRECT NAVIGATOR
CD
No.
01
02
03
04
05
0.09
Track1
5 Tracks / Total Play Time 20min54sec
Music list
Track Name
Track1
Track2
Track3
Track4
Track5
Up to 30 stations can be set.
1
2
Press [STATUS] to select the position to
start the auto preset search.
LOWEST:
To begin auto preset with the lowest frequency (FM87.9 or
FM87.5).
4.30
Play Time
4min30sec
3min41sec
4min30sec
3min11sec
5min 2sec
3
CURRENT:
To begin auto preset with the current frequency.*
* To change the frequency, refer to “Presetting stations
manually”.
Press and hold [OK].
Release the button when “AUTO” is displayed.
Play
RETURN
“
Press [RADIO] to select “FM”.
Playback
1
Presetting stations
automatically
Radio
SC-BTT770_370_270P_eng.book 29 ページ
The tuner starts to preset all the stations it can receive into
the channels in ascending order.
” indicates the track currently playing.
Playing a track in another
folder
1
≥ “SET OK” is displayed when the stations are set, and the radio tunes to the
last preset station.
≥ “ERROR” is displayed when automatic presetting is unsuccessful. Preset
the stations manually.
While the DIRECT NAVIGATOR screen is displayed
Presetting stations manually
Press [SUB MENU].
2
Press [3, 4] to select “Select Folder” and
press [OK].
≥ You cannot select folders that contain no compatible tracks.
Preparation
Select a radio broadcast.
1 Press [RADIO] to select “FM”.
2 Press [SEARCH6] or [SEARCH5] to select the
frequency.
≥ To start automatic tuning, press and hold [SEARCH6], [SEARCH5]
until the frequency starts scrolling. Tuning stops when a station is found.
1
While listening to the radio broadcast
Press [OK].
2
While “P” is flashing on the display
Press the number buttons to select a
channel.
To select a 1-digit number
e.g., 1: [1]
[OK].
To select a 2-digit number
e.g., 12: [1]
[2]
≥ A station previously stored is overwritten when another station is stored in
the same channel preset.
VQT3D27
29
SC-BTT770_370_270P_eng.book 30 ページ
2010年12月16日 木曜日 午後9時51分
Enjoying TV with unit’s
speakers
TV
Listening/confirming the preset
channels
1
2
Press [RADIO] to select “FM”.
Preparation
Press the number buttons to select the
channel.
Turn on your TV and select the appropriate audio input mode
[AUX, ARC, D-IN] to suit the connections to this unit. ( 23)
To select a 1-digit number
e.g., 1: [1]
[OK].
To select a 2-digit number
e.g., 12: [1]
[2].
Alternatively, press [W, X] or [3, 4].
∫ Display on the main unit
TUNED/STEREO:
Displayed when receiving stereo broadcasting
TUNED:
Displayed when receiving monaural broadcasting or monaural
sound is selected.
Surround sound effects
You can enhance stereo sources with surround sound effect.
1
2
Surround modes to enjoy TV audio or stereo
sources from all speakers:
≥ DOLBY PRO LOGIC II MOVIE
≥ DOLBY PRO LOGIC II MUSIC
≥ SUPER SURROUND
1 Press and hold [jAUDIO] to activate to select the type.
2 Press [jAUDIO] to display “MONO”.
The sound becomes monaural.
For more detailed information on this operation, please refer to
the “Enjoying surround sound effects” section on page 24.
Sound modes
≥ This setting can be preset for each broadcasting station.
∫ FM frequency step
Main unit:
The factory setting is set to 0.2 MHz, it can be changed to
receive broadcasts allocated in 0.1 MHz. You may need to
change this setting if the tuner seems to skip over the correct
frequency for stations in your area.
1 Press [RADIO] to select “FM”.
2 Press and hold [RADIO].
After a few seconds the display changes to show the
current lowest frequency. Continue to hold the button
down. The lowest frequency changes and the step is
changed.
To return to the original settings, repeat steps 1 and 2.
≥ After changing the setting, previously preset frequencies will be cleared.
Preset them again.
VQT3D27
30
While “MANUAL” is displayed on the unit’s display
Press [2, 1] and select the desired effect.
∫ If noise is excessive
Press the button again in step 2 to cancel the mode. “AUTO
STEREO” will be displayed on the main unit. Depending on
the broadcast system, stereo or monaural will be selected.
“MONO” is also canceled when you change the frequency.
Press [SURROUND] several times to select
the effect.
You can adjust the mode depending on the source or situation.
1
2
Press [SOUND] several times to select the
mode.
While the selected mode is displayed on the unit’s
display
Press [2, 1] and select the desired setting.
For more detailed information on this operation, please refer to
the “Changing the sound modes” section on page 24.
2010年12月16日 木曜日 午後9時51分
TM
ControlTM”)
What is VIERA Link “HDAVI Control”?
VIERA LinkTM is a new name for EZ SyncTM.
VIERA Link “HDAVI Control” is a convenient function that
offers linked operations of this unit, and a Panasonic TV
(VIERA) under “HDAVI Control”.
You can use this function by connecting the equipment
with an HDMI cable. See the operating instructions for
connected equipment for operational details.
Preparation
1 Set “VIERA Link” to “On” ( 39).
(The default setting is “On”.)
2 Set the “HDAVI Control” operations on the connected
equipment (e.g., TV).
3 Turn on all “HDAVI Control” compatible equipment and
select this unit’s input channel on the connected TV so that
the “HDAVI Control” function works properly.
When the connection or settings are changed, repeat
this procedure.
Setting the audio link
∫ Setting the audio link with the TV
With the remote control:
≥ Select the actual TV audio connection on the main unit.
1 Press [HOME].
2 Press [3, 4, 2, 1] to select “Others” and press [OK].
3 Press [OK] to select “Setup”.
4 Press [3, 4] to select “TV / Device Connection”.
5 Press [3, 4] to select “TV Audio Input”.
6 Press [2, 1] to switch “AUX”, “ARC” or “DIGITAL IN” and
press [OK].
≥ Select “AUX” or “ARC”*1 in “TV Audio Input” when the
DIGITAL AUDIO IN terminal is used for the STB
connection.
Whenever the connection or settings are changed, reconfirm
the points above.
∫ Setting the audio link with the STB
With the remote control:
≥ Select the STB input channel on the TV.
1 Press [EXT-IN] to select “D-IN”.
2 Press [STATUS] to select “CABLE/SATELLITE AUDIO
ON”.
≥ VIERA Link “HDAVI Control”, based on the control functions provided by
HDMI which is an industry standard known as HDMI CEC (Consumer
Electronics Control), is a unique function that we have developed and
added. As such, its operation with other manufacturers’ equipment that
supports HDMI CEC cannot be guaranteed.
≥ This unit supports “HDAVI Control 5” function.
“HDAVI Control 5” is the newest standard (current as of December, 2010)
for Panasonic’s HDAVI Control compatible equipment. This standard is
compatible with Panasonic’s conventional HDAVI equipment.
≥ Please refer to individual manuals for other manufacturers’ equipment
supporting VIERA Link function.
Speaker control
You can select whether audio is output from the unit’s
speakers or the TV speakers by using the TV menu settings.
Home theater
This unit’s speakers are active.
≥ When this unit is in standby mode, changing the TV
speakers to this unit’s speakers in the TV menu will
automatically turn the unit on and select, “AUX”*2, “ARC”*1,*2
or “D-IN” (DIGITAL IN)*2 as the source.
≥ You can control the volume setting using the volume or mute
button on the TV’s remote control.
≥ If you turn off this unit, TV speakers will be automatically
activated.
TV
TV speakers are active.
≥ The volume of this unit is set to “0”.
≥ Audio output is 2-channel audio.
Radio
Linked operations with
the TV (VIERA Link “HDAVI
TV
SC-BTT770_370_270P_eng.book 31 ページ
≥ When switching between this unit’s speakers and TV speakers, the TV
screen may be blank for several seconds.
≥ The audio from “AUX”, “DIGITAL IN”, “FM Radio” or “iPod” will be output
from this unit's speakers even though the TV speakers are selected.
Automatic input switching
(Power on link)
When the following operations are performed, the television
will automatically switch the input channel and display the
corresponding action. When the TV is off, the TV will
automatically turn on.
jWhen play starts on the unit
jWhen an action that uses the display screen is performed
(e.g., DIRECT NAVIGATOR screen)
≥ When you switch the TV input to TV tuner mode, this unit will
automatically switch to “AUX”*2, “ARC”*1,*2 or “D-IN”
(DIGITAL IN)*2.
≥ This function does not work when the iPod/iPhone selector is
chosen. ( 33)
≥ If the input channel of the STB on the TV is changed or if you
want to change the device allocated for the linked
operations, select “CABLE/SATELLITE AUDIO OFF” in step
2 above and then repeat steps 1 to 2.
≥ If using “HDMI IN1” or “HDMI IN2” as a source, set to
“CABLE/SATELLITE AUDIO OFF” in step 2.
VQT3D27
31
SC-BTT770_370_270P_eng.book 32 ページ
2010年12月17日 金曜日 午後7時44分
Using the iPod/iPhone
Other devices
Automatic lip-sync function
(for HDAVI Control 3 or later)
Delay between audio and video is automatically adjusted,
enabling you to enjoy smooth audio for the picture ( 38,
“Audio Delay”).
≥ This function works only when “BD/DVD”, “SD”, “AUX”*2,
“ARC”*1,*2, “D-IN” (DIGITAL IN)*2 is selected as the source
on this unit.
*1
*2
The selection works only when using an ARC compatible TV.
“AUX”, “ARC” or “D-IN” works depending on the setting in “Setting the
audio link”.
Power off link
All connected equipment compatible with “HDAVI Control”,
including this unit, automatically turns off when you switch the
television off.
Playing music continuously even after turning off the TV
(When the unit is connected to a Panasonic TV (VIERA) that
supports HDAVI Control 2 or later.)
Select “Video” in “Power Off Link” ( 39)
Easy control only with VIERA
remote control
Only TV supports “HDAVI Control 2” or later
By using the TV remote control, you can play discs using the
“Control Panel” and display the Top Menu or Pop-up Menu,
etc.
≥ This works only during “BD/DVD” or “SD” playback and
resume modes.
1
Press [SUB MENU].
e.g. BD-Video
Screen Aspect
Top Menu
Pop-up Menu
2
OK
RETURN
Select an item, then press [OK].
≥ The sub menu may not appear while the Top Menu for
BD-Video or DVD-Video is displayed.
≥ The buttons that you can use for this unit can vary depending on the TV.
For details, refer to the operating instructions of the TV.
≥ The operation of this unit may be interrupted when you press incompatible
buttons on the TV remote control.
≥ Depending on the menu, some button operations cannot be performed
from the TV’s remote control.
VQT3D27
32
≥ Update your iPod/iPhone with the latest software before using this unit.
≥ Compatibility depends on the software version of your iPod/iPhone.
≥ iPod/iPhone compatibility assures music, video playback and battery
charge functions of this unit as a home theater system.
Name
Memory Size
iPod touch 4th generation
8 GB, 32 GB, 64 GB
iPod nano 6th generation*
8 GB, 16 GB
iPod touch 3rd generation
32 GB, 64 GB
iPod nano 5th generation (video camera)
8 GB, 16 GB
iPod touch 2nd generation
8 GB, 16 GB, 32 GB
iPod classic
120 GB, 160 GB (2009)
iPod nano 4th generation (video)
8 GB, 16 GB
iPod classic
160 GB (2007)
iPod touch 1st generation
8 GB, 16 GB, 32 GB
iPod nano 3rd generation (video)
4 GB, 8 GB
iPod classic
80 GB
iPod nano 2nd generation (aluminum)
2 GB, 4 GB, 8 GB
iPod 5th generation (video)
60 GB, 80 GB
iPod 5th generation (video)
30 GB
iPod nano 1st generation
1 GB, 2 GB, 4 GB
iPhone 4
16 GB, 32 GB
iPhone 3GS
8 GB, 16 GB, 32 GB
iPhone 3G
8 GB, 16 GB
* Playback functions on the main unit may be limited in the “All” mode.
In some locations, reception status of an iPhone may be poor when it is
loaded on this unit.
≥ When the iPhone receives a call while connected to this unit, playback, etc.
of the iPhone may stop.
To prioritize the operation with the iPhone connected to this unit, make the
setting so that the iPhone does not receive calls.
iPod/iPhone Connection
Preparation
Control Panel
SUB
MENU
Compatible iPod/iPhone (as of December 2010)
≥ Before connecting/disconnecting the iPod/iPhone, turn the
main unit off or reduce the volume of the main unit to its
minimum.
≥ Make sure that the video cable connection is made to view
photos/videos from the iPod/iPhone.
1
Push the center of drawer (A), and pull out
fully until it clicks to open the Dock for
iPod/iPhone (C).
2
Install a Dock adapter (not supplied) (B)
before inserting your iPod/iPhone into the
dock.
3
Connect the iPod/iPhone (not supplied)
firmly.
VQT3D27~Body_mst.fm 33 ページ
2010年12月17日 金曜日 午後8時59分
iPod/iPhone Playback

1
Preparation
≥ Make sure that the “IPOD” source is selected. Press [iPod] to
select the source.
≥ To view photos/videos from the iPod/iPhone
Operate the iPod/iPhone menu to make the appropriate
photo/video output settings for your TV.
≥ To display the picture, turn on the TV and select the
appropriate video input mode.
iPod/iPhone
3
Enjoy music/video
1
2
2 
Press [iPod] to select “IPOD”.
Press [STATUS] several times to select the
music menu or videos menu.
≥ You can also select "Videos" or "Music" by using HOME
menu. (> 23)
3
A The center of drawer
B Dock adapter (not supplied)
≥ Please be sure to use the adapter that is compatible
with your model of iPod/iPhone.
≥ Attach the dock adapter until it is firmly in place.
≥ To purchase a dock adapter, consult your local iPod/
iPhone dealer.
C Dock for iPod/iPhone
D Make sure to match when inserting.
≥ Carefully insert and remove the iPod/iPhone to
ensure long lasting product enjoyment.
≥ Check that the connector has no dust or foreign
materials before connecting.
≥ The 3D logo on the Dock for iPod/iPhone does not mean that the iPod/
iPhone has 3D capabilities.
≥ Avoid using Wi-Fi mode on your iPhone while the network functions or
surround speakers on this unit are in use wirelessly.
About recharging the battery
≥ iPod/iPhone will start recharging regardless of whether this unit is on or off.
≥ “IPOD ¢” will be shown on the main unit’s display during iPod/iPhone
charging in main unit standby mode.
≥ Once fully recharged, additional recharging will not occur.
≥ Repeat this step until the selected title starts playback.
≥ Press [2, 1] to display the previous or next page.
e.g., music playback screen
iPod
TV
Main unit
Press [3, 4] to select an item and press
[OK].
Good morning
Ronaldo

Happy days
1:00
-2:30
45 of 1230
A Album artwork
≥ If album artwork is contained in the data of a song, it
will appear on the TV. If there is no album artwork,
“
” will be appear on TV.
≥ Depending on the software version of your iPod/
iPhone, the album artwork may not appear properly.
≥ It may take time to read the album artwork.
≥ Some operations may not work while reading the
album artwork.
Other devices


To exit, press [RETURN].
Basic controls
(For music and video playback only)
Buttons
[1 PLAY]
[∫STOP]
[;PAUSE]
[:, 9]
(Press and hold)
[SEARCH6, SEARCH5]
Functions
Play
Pause
Skip
Search
VQT3D27
33
VQT3D27~Body_mst.fm 34 ページ
2011年1月5日 水曜日 午前11時14分
Enjoying
VIERA CASTTM
Advanced operations
Enjoy photos
1
2
3
4
Press [iPod] to select “IPOD”.
Press [STATUS] several times to select
“ALL” on the unit’s display.
≥ You can also select "All" by using HOME menu. (> 23)
Switch the TV input to video in.
Play a slideshow on your iPod/iPhone.
The picture will be displayed on your TV.
To use the iPod touch/iPhone features
1 Press the Home button on the iPod touch/iPhone.
2 Select the iPod touch/iPhone features on the touch screen
to operate.
You can use the remote control to operate the iPod/iPhone
menu.
The operation may vary among iPod/iPhone models.
≥ [3, 4]: To navigate menu items
≥ [OK]: To go to the next menu.
≥ [RETURN]: To return to the previous menu.
You can access a selection of Internet services from the Home
screen with VIERA CAST, for example YouTube, Picasa Web
Albums. (Current as of December 2010)
Preparation
≥ Network connection (> 17)
≥ Network setting (> 20)
[BTT770] [BTT370]
To enjoy video communication (ex. SkypeTM) :
≥ Connect this unit with optional Communication Camera
(TY-CC10W or compatible equipment).
Depending on the area, this optional camera may not be
available. Please consult your local Panasonic dealer for
advice.
Other methods of playback
COMMUNICATION
CAMERA
Back of the unit
1
2
Press [SUB MENU].
Press [3, 4] to select the item and press
[OK].
Playback Mode
Shuffle (For music playback only.)
Songs:
Play all songs on iPod/iPhone in random order.
Albums:
Play all songs on an album in random order.
Repeat
One:
Play a single song/video repeatedly.
All:
Play all songs/videos from selected items (e.g., Playlists,
Albums, etc.) repeatedly.
iPod Information
Display the firmware version of iPod/iPhone.
3
Press [3, 4] to select the setting and press
[OK].
≥ The setting of the playback mode will be kept until changes are made on
the same iPod/iPhone.
≥ This function does not work when “All” is selected.
≥ Surround sound effect and sound mode are available (> 24).
Communication camera
TY-CC10W
≥ For operating method refer to the following website.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
1
Press [VIERA CAST].
≥ [BTT770] [BTT370] The video communication service can
be accessed directly by pressing [
] button.
≥ NETFLIX can be accessed directly by [NETFLIX] button.
≥ Message is displayed. Please read these instructions
carefully and then press [OK].
2
Press [3, 4, 2, 1] to select the item and
press [OK].
Operable buttons:
[3, 4, 2, 1], [OK], [RETURN], colored buttons, number
buttons
VIERA CAST Home screen;
Weather
New York, NY
69°
TOMORROW
NW 10
mph
H
L
76°
56°
XXXXXX
XXXXXX
Featured Photos
Featured Videos
XXXXXXXXXXX
Hit Movies
MORE
BACK
Top TV Shows
Watch Instantly
Images are for illustration purposes, contents may change
without notice.
To exit from VIERA CAST
Press [EXIT] or [HOME].
VQT3D27
34
2010年12月16日 木曜日 午後9時51分
≥ When playing content from a disc/SD card VIERA CAST cannot be
accessed by pressing [VIERA CAST].
≥ In the following cases, settings are possible using “Internet Content
Settings” ( 40)
– When restricting the use of VIERA CAST.
– When the audio is distorted.
– When wrong time is displayed
≥ If using slow Internet connection, the video may not be displayed correctly.
A high-speed Internet service with a speed of at least 6 Mbps is
recommended.
≥ Be sure to update the firmware when a firmware update notice is displayed
on the screen. If the firmware is not updated, you will not be able to use the
VIERA CAST function. ( 22)
≥ VIERA CASTTM home screen is subject to change without notice.
≥ The services through VIERA CASTTM are operated by their respective
service providers, and service may be discontinued either temporarily or
permanently without notice. Therefore, Panasonic will make no warranty
for the content or the continuity of the services.
≥ All features of websites or content of the service may not be available.
≥ Some content may be inappropriate for some viewers.
≥ Some content may only be available for specific countries and may be
presented in specific languages.
Playback menu
1
Press [DISPLAY].
e.g., BD-Video
Disc
Play
Video
Audio
Signal Type
Subtitle
Off
-
Subtitle Style
Menus
Items
Main
1ENG
Angle
-
Settings
2
Press [3, 4] to select the menu and press
[1].
3
Press [3, 4, 2, 1] to select the item and
press [1].
4
Press [3, 4] to select the setting.
Some items can be changed by pressing [OK].
To exit the screen
Press [DISPLAY].
Depending on the condition of the unit (playing, stopped,
etc.) and media contents, there may be some items that
you cannot select or change.
Regarding Language: ( 46)
Disc
Signal Type
Primary
Video
Secondary
Video
Video
The recording method of
original video appears.
Soundtrack
Select the type of audio or
language.
Video
Select on/off of images. The
recording method of original
video appears.
Soundtrack
Select on/off of audio and the
language.
Video
The recording method of original video appears.
Other devices
Advanced operations
SC-BTT770_370_270P_eng.book 35 ページ
Soundtrack
Show or change the soundtrack.
Subtitle
Turn the subtitle on/off, and change the language depending
on the media.
Subtitle Style
Select the subtitle style.
Audio channel
Select the audio channel number.
( 25, “Changing audio”)
Angle
Select the number of the angle.
Some items may be changed only on the disc specific menu. (
25)
VQT3D27
35
SC-BTT770_370_270P_eng.book 36 ページ
2010年12月17日 金曜日 午後7時44分
Play
Repeat Play
Movie Sound Effect
(Only when the elapsed time is being displayed on the unit’s
display.)
Select the item which you want to repeat. The items displayed
differ depending on the type of media.
Select the sound effect of the movie.
≥ Cinema Surround Plus:
The function creates the sound of virtual speakers to
enhance the realistic surround feeling as if the sound comes
from all directions.
Select “Off” to cancel.
Random
Select whether or not to play random.
Pop-Out Level
[Only when “Full HD” is selected in “3D Type” ( 39).]
Pop-up position for the Playback menu or message screen etc.
can be adjusted during 3D playback.
Video
Select the sound effect of the music.
≥ Digital Tube Sound:
This feature gives you warm sound, like that produced by a
vacuum tube amplifier.
≥ Re-master:
This feature gives you brighter sound by increasing the high
frequency portion of the audio. (Discs recorded at 48 kHz or
less)
Recommended settings:
Pop and rock
Picture
Re-master 2
Jazz
Select the picture quality mode during play.
Re-master 3
Classical
High Clarity Sound
Chroma Process
The high-resolution processing of HDMI chroma signals
produces a high-resolution picture with rich picture quality.
When connected to TV via the HDMI AV OUT terminal for
outputting image, it produces clearer sound.
≥ Only when you have selected “Enable” in “High Clarity
Sound” ( 38).
Detail Clarity
The picture is sharp and detailed.
*1
Super Resolution
Pictures of normal image quality are corrected to sharp and
detailed images when output as 1080i/1080p from HDMI AV
OUT.
Progressive
Select the method of conversion for progressive output to suit
the type of material being played.
≥ When the content is distorted change the settings from
“Auto” to “Video”.
24p
Movies and other material recorded on DVD-Video at 24p are
output at 24p.
≥ Only when you have selected “On” in “24p Output” ( 39)
36
Music Sound Effects*1, *2
Re-master 1
Advanced Setting
VQT3D27
Audio
*2
When audio is output from the HDMI AV OUT terminal this function is
effective only when “Dolby D/Dolby D +/Dolby TrueHD” or “DTS/
DTS-HD” is set to “PCM”. ( 38)
This function has no effect when the type of audio is Dolby Pro Logic II.
2010年12月24日 金曜日 午後7時28分
Setup menu
Change the unit’s settings if necessary. The settings remain
intact even if you switch the unit to standby.
1
2
3
Press [HOME].
Press [3, 4, 2, 1] to select “Others” and
press [OK].
Press [OK] to select “Setup”.
Setup
Disc
Video
Audio
Display
DVD-Video Ratings
Set a ratings level to limit DVD-Video play.
≥ Follow the on-screen instructions. Enter the 4-digit password
with the number buttons when the password screen is
shown.
BD-Video Ratings
Set an age limit of BD-Video play.
≥ Follow the on-screen instructions. Enter the 4-digit password
with the number buttons when the password screen is
shown.
TV / Device Connection
3D BD-Video Playback
Network
Select the playback method of 3D compatible video software.
Others
OK
RETURN
4
Press [3, 4] to select the menu and press
[OK].
5
Press [3, 4] to select the item and press
[OK].
If there are any other items, repeat these steps.
6
Disc
Press [3, 4, 2, 1] to select the option and
press [OK].
≥ There may be differences in operation methods. If this happens, follow the
on-screen instructions for the operation.
About the password
The following items use the same password.
Don’t forget your password.
≥ “DVD-Video Ratings”
≥ “BD-Video Ratings”
≥ “Lock” (> 40)
Audio Language
Choose the language for audio.
≥ If “Original” is selected, the original language of each disc
will be selected.
≥ Enter a code (> 46) with the number buttons when you
select “Other ¢¢¢¢”.
Subtitle Language
Choose the language for the subtitle.
≥ If “Automatic” is selected and the language selected for
“Audio Language” is not available, subtitles of that language
will automatically appear if available on that disc.
≥ Enter a code (> 46) with the number buttons when you
select “Other ¢¢¢¢”.
Menu Language
Choose the language for the disc menus.
≥ Enter a code (> 46) with the number buttons when you
select “Other ¢¢¢¢”.
BD-Live Internet Access (> 26)
You can restrict Internet access when BD-Live functions are
used.
≥ If “Allow ( Limited )” is selected, Internet access is permitted
only for BD-Live contents which have content owner
certificates.
Advanced operations
VQT3D27~Body_mst.fm 37 ページ
VQT3D27
37
VQT3D27~Body_mst.fm 38 ページ
2010年12月17日 金曜日 午後1時7分
Downmix
Video
Still Mode (paused video)
Select the type of picture shown when you pause playback.
Auto
Automatically selects the type of picture
shown.
Field
Select if jittering occurs when “Auto” is
selected.
Frame
Select if small text or fine patterns cannot
be seen clearly when “Auto” is selected.
Seamless Play
The chapter segments in playlists are played seamlessly.
≥ Select “On”, when the picture freezes for a moment at the
chapters segment in playlists.
Select the downmix system to enjoy multi-channel or
2-channel sound.
≥ Select “Surround encoded” to enjoy the surround sound.
≥ There is no downmix effect on the bitstream audio signal.
≥ The audio will be output in “Stereo” in the following cases:
– AVCHD playback
– Dolby TrueHD playback
– Playback of secondary audio (including the button click
sound).
High Clarity Sound
When connected to TV via the HDMI AV OUT terminal for
outputting image, it produces clearer sound.
≥ Set to “Enable” and then set “High Clarity Sound” on the
Playback menu to “On”. (> 36)
Audio Delay
Black Level Control
Mis-sync between the video and audio is corrected by delaying
the audio output.
Select lighter or darker for adjusting the black level control to
the desired setting for picture enhancement.
Speaker
Refer to page 41
Audio
Dynamic Range Compression
You can listen at low volumes but still hear dialog clearly.
(Dolby Digital, Dolby Digital Plus and Dolby TrueHD only)
≥ “Auto” is effective only when playing Dolby TrueHD.
Status Messages
Digital Audio Output
Choose the language for menus and on-screen messages.
Press [OK] to show the following settings:
Dolby D/Dolby D +/Dolby TrueHD
DTS/DTS-HD
Select the audio signal to output.
≥ Select “PCM”, when the connected equipment cannot
decode the respective audio format.
≥ Not making the proper settings may result in noise.
BD-Video Secondary Audio
Select whether to mix or not mix the primary audio and
secondary audio (including the button click sound). (> 26)
≥ If “Off” is selected, the unit outputs the primary audio
only.
Digital Audio Input
Press [OK] to show the following settings:
PCM-FIX
Select the following audio signal to input.
jARC
jDIGITAL IN
j[BTT770] [BTT370] HDMI Input1
j[BTT770] [BTT370] HDMI Input2
≥ “On”: PCM is available.
≥ “Off”: DTS, PCM and Dolby Digital are available.
Select “On” if the sound is cut off intermittently.
VQT3D27
38
Display
Choose whether to show status messages automatically.
On-screen Language
Screen Saver Function
This is to prevent burn-in on the screen.
≥ When this is set to “On”:
If there is no operation for 5 minutes or more, DIRECT
NAVIGATOR screen switches to HOME menu automatically.
≥ While playing and pausing, etc., this function is not available.
≥ While playing music (CD-DA or MP3), after about 5 minutes
DIRECT NAVIGATOR screen switches to a blank screen
with “Screen Saver” message.
Front Panel Display
Changes the brightness of the unit’s display.
≥ If “Auto” is selected, the display is dimmed but brightens
when you perform some operations.
License
Information about the software used by this unit is displayed.
2010年12月16日 木曜日 午後9時51分
TV / Device Connection
3D Settings
Press [OK] to show the following settings
3D Type
Select the format of the connected TV.
≥ Change the settings for 3D on the TV also when
“Checker board” or “Side by side” is selected.
3D Playback Precautions
Set to display or hide the 3D viewing warning screen when
playing back the 3D compatible video software.
TV Aspect
Set to match the type of television connected.
When connected to a 4:3 aspect television and playing 16:9
ratio image:
4:3
4:3
Letterbox
The sides are cut off so
the picture fills the
screen. When playing
BD-Video, video is output
as “4:3 Letterbox”.
Black bands appear at the
top and bottom of the
picture.
When connected to a 16:9 widescreen television and playing
4:3 ratio image:
16:9
Video is displayed as a 4:3 ratio image in
the center of the screen.
HDMI Connection
Press [OK] to show the following settings:
HDMI Resolution
The items supported by the connected devices are
indicated on the screen as “¢”. When any item without “¢”
is selected, the images may be distorted.
≥ If “Auto” is selected, automatically selects the output
resolution best suited to the connected television.
≥ To enjoy high-definition video up-converted to 1080p,
you need to connect the unit directly to 1080p
compatible HDTV (High Definition Television). If this unit
is connected to an HDTV through other equipment, it
must also be 1080p compatible.
24p Output
When this unit is connected to a TV supporting 1080/24p
output using an HDMI cable, movies and other material
recorded at 24p are output at 24p.
≥ When playing DVD-Video, set to “On” and then also set
“24p” in “Video” ( 36) to “On”.
≥ When BD-Video images other than 24p are played,
images are output at 60p.
≥ 24p :
A progressive image recorded at a rate of 24 frames per
second (motion-picture film). Many BD-Video movie
contents are recorded in 24 frames/second in
accordance with the film materials.
HDMI Color Mode
This setting is for selecting color-space conversion of the
image signal when the unit is connected using an HDMI
cable.
HDMI Audio Output
This setting selects whether or not to output audio from
HDMI.
≥ Audio will be output through the system's speakers when
"Off" is selected.
[BTT770] [BTT370]
HDMI Standby Pass-Through
Even if this unit is in standby mode, a device connected
with this unit can output videos and sound to the TV.
Moreover, you can switch the HDMI input terminal by
pressing [EXT-IN] on the remote control.
≥ Sound will not be output from this unit's speakers.
VIERA Link
Set to use “HDAVI Control” function when connected with
an HDMI cable to a device that supports “HDAVI Control”.
≥ Select “Off” when you do not want to use “HDAVI
Control”.
Deep Color Output
This setting is for selecting whether to use Deep Color
output when a television that supports Deep Color is
connected.
Contents Type Flag
Depending on the playback content, the TV will output
adjusting to the optimal method when a TV that supports
this function is connected.
Power Off Link
Select the desired power off link setting of this unit for
VIERA Link operation ( 32). (This works depending on
the settings of the connected VIERA Link “HDAVI Control”
compatible equipment.)
Video/Audio:
When the TV is turned off, this unit will turn off
automatically.
Video:
When the TV is turned off, this unit will turn off except
during the following conditions:
jCD or MP3 audio playback
jiPod/iPhone mode
jRadio mode
j“AUX”,“ARC” or “D-IN” (DIGITAL IN) mode (non-selected
TV AUDIO setting for VIERA Link)
j“D-IN” (DIGITAL IN) mode (non-selected CABLE/
SATELLITE AUDIO setting for VIERA Link)
Advanced operations
SC-BTT770_370_270P_eng.book 39 ページ
TV Audio Input
Select the TV audio input to work with the VIERA Link
operations.
VQT3D27
39
VQT3D27~Body_mst.fm 40 ページ
2011年1月24日 月曜日 午前11時46分
Network
Network Easy Setting (> 20)
Remote Control Code
Network Settings
Change the remote control code, when other Panasonic
products react to this remote control.
Perform network-related settings individually.
Press [OK] to show the following settings:
Quick Start*
LAN Connection Mode
Select connection method.
Wireless Settings
This allows the Wireless router and connection settings to
be set and the current connection settings and connection
state to be checked when a wireless connection is used.
Connection Setting
The Wireless router connection wizard will be displayed.
IP Address / DNS Settings
This is for checking the state of the network connection
and setting the IP address and DNS-related.
Press [OK] to show the respective setting.
≥ “Connection Speed Setting” is enabled only when “Auto
Detect Connection Speed” is turned “Off”.
Proxy Server Settings
This is for checking the state of connection with the Proxy
server and performing settings.
Press [OK] to show the respective setting.
Internet Content Settings (> 34) (VIERA CAST)
Press [OK] to show the following settings:
Lock
You can restrict the usage of VIERA CAST.
≥Follow the on-screen instructions. Enter the 4-digit
password with the number buttons when the password
screen is shown.
Audio Auto Gain Control
Volume that is different depending on the contents is
adjusted automatically to the standard volume while
using the VIERA CAST.
≥Depending on contents, this function effect will not
work.
≥Select “Off” when the audio is warped.
Time Zone
By selecting the time zone, it is possible to set the unit’s
time to match your location.
≥Some VIERA CAST contents require the time zone to
be set. Set the time zone if necessary.
DST
Select “On” when using Daylight Saving time.
MAC Address
Displays the MAC address of this unit.
VQT3D27
40
Others
Speed of startup from power off is increased.
≥ Internal control unit will be powered when it is set to “On”, so
contents of the following will be different from the time it is
set to “Off”.
– Idle power consumption will increase. (More about the
power consumption > 48)
* Depending on the power conserving setting activated on
the TV, this function may have less effect when the unit is
started by the power on link function. (> 31)
Easy setup (> 19)
You can execute basic settings to optimize your home theater
system.
Restore Default Settings
This returns all values in the Setup menu and the Playback
menu, except for “Remote Control Code”, “LAN Connection
Mode”, “Wireless Settings”, “IP Address / DNS Settings”,
“Proxy Server Settings”, “Lock”, “DVD-Video Ratings” and
“BD-Video Ratings” etc. to the default settings.
System Information
Display firmware version of this unit and wireless LAN module.
Firmware Update (> 22)
Press [OK] to show the following settings:
Automatic Update Check
When this equipment remains connected to the Internet, it
will check for the latest firmware version when it is turned
on and you can update it if necessary.
Update Now
You can update the firmware manually.
SC-BTT770_370_270P_eng.book 41 ページ
2010年12月16日 木曜日 午後9時51分
B Surround speaker / Surround back speaker
Speaker settings
Difference
Setting
Delay time
Approx. 170 cm (5 ft. 6 in.)
5.0 ms
For optimum listening with 5.1-channel sound, all the
speakers, except for the subwoofer, should be the same
distance from the seating position.
If either distance A or B is less than C, find the difference in
the relevant table and adjust the delay time to make up for the
difference.
Approx. 340 cm (11 ft. 1 in.)
10.0 ms
Approx. 510 cm (16 ft. 8 in.)
15.0 ms
A
C
C
L
:
B
C
:
C
∫ When using the 7.1ch speaker system
1 Check the distance difference of both the front speakers
and the surround back speakers from the seating position.
2 Set the delay time of the surround back speakers.
R
A
[BTT770] [BTT370]
SW
B
LS
Adjusting speaker level
D
RS
LS
RS
A B C: Primary listening distance
A Approximate room dimensions
B Actual speaker position
C Ideal speaker position
D Circle of constant primary listening distance
Volume (Channel balance) (
1
2
1
C
Complete
Press [3, 4] to adjust the volume of each
speaker.

ms
0.0
The volume can be adjusted between r6 dB to s6 dB.
≥ Set each speaker level according to the volume of the
Front (L) and Front (R) speaker volume respectively.
R
dB
0
Test
dB
0
dB
0
3
e.g., 5.1ch setting
RS

A Center (C)
B Left Surround (LS), Right Surround (RS)
ms
0.0
C
Complete
dB
0
Test
dB
0
dB
0
ms
0.0



LB
ms
0.0
dB
0
dB
0
Test
dB
0
dB
0
ms
0.0
R
SW
dB
0
RS
SW
A Center (C)
B Test
C Left Surround (LS), Right Surround (RS)
RB
C Left Surround back (LB), Right Surround back (RB)
2
Complete
LS
RS
dB
0
C
R
dB
0
LS
ms
0.0
L
e.g., [BTT770] [BTT370] 7.1ch setting
L
Press [OK].
The test signal stops.
SW
dB
0
LS
While listening to the test signal
Advanced operations
ms
0.0
Select “Test” and press [OK].
A test signal is output.
e.g., 5.1ch setting
L
)
(Effective when playing multi-channel audio)
Press [3, 4, 2, 1] to select the distance
box ( ms
0.0 ) and press [OK].

dB
0
To finish the speaker setting
Press [3, 4, 2, 1] to select “Complete” and press [OK].
Press [3, 4] to select the setting and press
[OK].
A Center speaker
Difference
Setting
Approx. 34 cm (1 ft. 1 in.)
1.0 ms
Approx. 68 cm (2 ft. 2 in.)
2.0 ms
Approx. 102 cm (3 ft. 4 in.)
3.0 ms
Approx. 136 cm (4 ft. 5 in.)
4.0 ms
Approx. 170 cm (5 ft. 6 in.)
5.0 ms
VQT3D27
41
VQT3D27~Body_mst.fm 42 ページ
2011年1月6日 木曜日 午後1時40分
Speaker installation
option
Optional speaker settings
F
G
H
I
Attaching to a wall
You can attach all of the speakers (except subwoofer) to a wall.
≥ The wall or pillar on which the speakers are to be attached
should be capable of supporting 10 kg (22 lbs) per screw.
Consult a qualified building contractor when attaching the
speakers to a wall. Improper attachment may result in
damage to the wall and speakers.
≥ Do not attempt to attach these speakers to walls using
methods other than those described in this manual.
1
Drive a screw (not supplied) into the wall.
A At least 30 mm (1 3/16q)
B ‰ 4.0 mm (5/32q)
C ‰ 7.0 mm to ‰ 9.4 mm
(9/32q to 3/8q)
D Wall or pillar
E 5.5 mm to 7.5 mm
(7/32q to 5/16q)
2



≥ Move the speaker so that
the screw is in this
position.
Use the measurements indicated below to identify the
screwing positions on the wall.
≥ Leave at least 20 mm (25/32q) of space above the speaker and
10 mm (13/32q) on each side to allow enough space for fitting
the speaker.
[BTT770] [BTT370] [BTT273]
Front speaker
Attach to a wall without the base and the stand.

[BTT770]
[BTT370] [BTT273]

 

VQT3D27
42

 


[BTT770]
Center speaker





e.g., [BTT770] Front speaker
DO NOT
DO

[BTT770] [BTT370] [BTT273]
Surround speaker
[BTT270]
Front speaker,
Surround speaker

Fit the speaker securely onto the screw(s)
with the hole(s).
≥ In this position, the
speaker will likely fall if
moved to the left or right.
J
K
L
M
N
O
28.5 mm (1 1/8q)
97 mm (3 13/16q)
335 mm (13 3/16q)
210 mm to 212 mm
(8 9/32q to 8 11/32q)
40 mm (1 9/16q)
63 mm (2 15/32q)
322 mm (12 11/16q)
40 mm (1 9/16q)
17.6 mm (11/16q)
98.7 mm (3 7/8q)

[BTT370] [BTT270] [BTT273]
Center speaker
P 18.8 mm (3/4q)
Q 117 mm (4 19/32q)
R 209 mm to 211 mm
(8 7/32q to 8 5/16q)
S 97 mm (3 13/16q)
T 23 mm (29/32q)
U 95 mm to 97 mm
(3 3/4q to 3 13/16q)
V 26 mm (1 1/32q)
W 16.7 mm (21/32q)
X 63.7 mm (2 1/2q)






[BTT770] [BTT370] [BTT273]
∫ To avoid speaker dropping
Front speaker, Center speaker
e.g., [BTT770] Front speaker




A
B
C
D
String (not supplied)
Screw eye (not supplied)
Less than 10 cm (3 15/16q)
Rear of the speaker
≥ Consult a qualified building contractor to avoid damage to
the wall or speakers.
≥ Use a string of less than ‰ 2.0 mm (3/32q), which is capable of
supporting over 10 kg (22 lbs).
2010年12月24日 金曜日 午後6時48分
Before requesting service, please perform the
following steps.
Disc cannot be played.
≥ The disc is dirty. (> 9)
≥ Check the region code.
Do you have the latest firmware installed?
Still pictures (JPEG) do not playback normally.
≥ The images that were edited on the PC, such as Progressive
JPEG, etc., may not playback.
Firmware updates may be released to correct operating
irregularities that are discovered with certain movies. (> 22)
4
The TV tuner mode is not displayed when the TV is
switched on.
Make the following checks and visit our
website for more information.
For U.S.A. :
http://www.panasonic.com/help
Enter the model number.
For Canada :
http://www.panasonic.ca
4
Or visit our website to find a service
center.
You can find a service center near you easily on our website.
Other support information:
“Customer Services Directory (United States and Puerto
Rico)” (> 50) or “Limited Warranty (Only for CANADA)”
(> 51)
The following do not indicate a problem with this unit:
jRegular disc rotating sounds.
jImage disturbance during search.
jImage disturbance when replacing 3D discs.
∫ Unit does not respond to the remote
control or front panel buttons.
Press and hold [POWER Í/I] on the main unit for 5 seconds.
jIf still unable to power the unit off, disconnect the power cord,
wait 1 minute, then reconnect the power cord.
∫ Cannot eject disc.
The unit may have a problem.
While the unit is off, press and hold [9] on the remote
control and [< OPEN/CLOSE] on the unit at the same time for
more than 5 seconds.
General operation
To return to the factory preset
≥ Select “Yes” in “Restore Default Settings” in the Setup menu.
(> 40)
To return all settings to the factory preset
≥ Reset the unit as follows:
While the unit is off, press and hold [+ VOLUME], [< OPEN/
CLOSE] and [POWER Í/I] on the main unit at the same
time for more than 5 seconds.
The remote control doesn’t work properly.
≥ Change the batteries in the remote control. (> 9)
≥ The remote control and main unit are using different codes. If
“SET ” is displayed on the unit’s display when a button is
pressed on the remote control, change the code on the
remote control. (> 40)
≥ This phenomenon may occur, depending on the TV setting,
when “Quick Start” is set to “On”.
≥ Depending on the TV, this phenomenon may be prevented
by reconnecting the HDMI cable to a different HDMI input
terminal or by changing the HDMI auto connection setting.
You have forgotten your ratings password.
You want to cancel the ratings level.
The ratings level returns to the factory preset.
1 While the unit is on, press and hold [OK], [B] and [Y] on the
remote control at the same time for more than 5 seconds.
j“00 RET” is displayed on the unit’s display.
2 Repeatedly press [1] (right) on the remote control or
[POWER Í/I] on the unit until “03 VL” is displayed on the
unit’s display.
3 Press [OK] on the remote control or [< OPEN/CLOSE] on
the unit.
This unit does not recognize the communication camera
correctly.
≥ Disconnect and reconnect the communication camera. If it
still does not recognize the connection, turn the power of this
unit off and on again.
Power
No power.
≥ Insert the AC power supply cord securely into a household
AC outlet. (> 18)
The unit switches to standby mode.
≥ This unit will automatically turn to standby mode after 30
minutes if it is inactive. (> 7)
≥ When the time set for the sleep timer has passed, the power
will be turned off. (> 6)
≥ One of the unit’s safety devices is activated. Press
[POWER Í/I] on the main unit to turn the unit on.
This unit is turned off when the input for the TV is switched.
≥ This is a normal phenomenon when using VIERA Link
(HDAVI Control 4 or later). For details please read the
operating instructions for the TV.
The unit does not turn off.
1 Press and hold [POWER Í/I] on the main unit for 5 seconds.
(If still unable to power the unit off, disconnect the power
cord, wait 1 minute, then reconnect the power cord.)
2 Reset the unit as follows:
While the unit is off, press and hold [+ VOLUME],
[< OPEN/CLOSE] and [POWER Í/I] on the main unit at
the same time for more than 5 seconds.
Optional speaker
settings
Troubleshooting guide
Reference
Reference
VQT3D27~Body_mst.fm 43 ページ
Displays
The display is dim.
≥ Change “Front Panel Display” in the Setup menu. (> 38)
VQT3D27
43
SC-BTT770_370_270P_eng.book 44 ページ
2010年12月16日 木曜日 午後9時51分
TV screen and video
Sound
The images from this unit do not appear on the TV.
Picture is distorted.
Jittering occurs.
≥ An incorrect resolution is selected in “HDMI Resolution”.
Reset the setting as follows:
1 While the unit is on, press and hold [OK], [B] and [Y] on the
remote control at the same time for more than 5 seconds.
j“00 RET” is displayed on the unit’s display.
2 Repeatedly press [1] (right) on the remote control or
[POWER Í/I] on the unit until “04 PRG” is displayed on
the unit’s display.
3 Press and hold [OK] on the remote control or [< OPEN/
CLOSE] on the unit for at least 3 seconds.
Set the item again. ( 39)
jWhen Dolby Digital Plus, Dolby TrueHD, and DTS-HD
audio are not output in bitstream, select “Yes” in “Restore
Default Settings” and make proper settings. ( 40)
≥ When “3D BD-Video Playback” in the Setup menu is set to
“Automatic”, images may not be output depending on the
connection method. After removing the disc from this unit,
select “Set before play” in the Setup menu, and select “2D
Playback” in the setup screen displayed when playing 3D
discs. ( 37)
Video is not output.
≥ Set “High Clarity Sound” in the Playback menu to “Off” to use
the VIDEO OUT terminal. ( 36)
Video is not output in high-definition.
≥ Confirm that “HDMI Resolution” in the Setup menu is set
properly. ( 39)
3D video is not output.
≥ Are the settings on this unit and the TV correct? (
27)
3D video is not output correctly as 2D.
≥ Select “Set before play” in the Setup menu, and select “2D
Playback” in the setup screen displayed when playing 3D
discs. ( 37)
≥ Discs that have recorded titles with Side by side (2 screen
structure) and that can be enjoyed in 3D are played back in
accordance with the settings of the TV.
No subtitles.
≥ When progressive output is on, closed captions/subtitles
cannot be displayed.
The subtitles overlap closed captions recorded on discs.
≥ Turn off the subtitles or turn off the closed caption setting on
the TV. ( 35)
A black band is displayed around the edge of the screen.
The aspect ratio of the screen is abnormal.
≥ Confirm the “TV Aspect” is set properly. ( 39)
≥ Adjust the aspect setting on the television.
VQT3D27
44
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio type.
≥ Check connections to speakers and other equipment.
( 10, 11, 13s18)
≥ Ensure the speaker settings for your speakers are correct. ( 41)
≥ To output audio from a device connected with an HDMI cable,
set “HDMI Audio Output” to “On” in the Setup menu. ( 39)
≥ When “BD-Video Secondary Audio” is set to “On”, Dolby
TrueHD, Dolby Digital Plus, DTS-HD Master Audio and
DTS-HD High Resolution Audio are output as Dolby Digital
or DTS Digital Surround.
≥ Re-master will not work when the bitstream signal is output
from the HDMI AV OUT terminal. ( 36)
≥ Depending on the connected equipment, the sound may be
distorted if this unit is connected with an HDMI cable.
≥ The multi-channel audio from a device connected to the TV
is not output in it’s original multi-channel form.
jIf the device has an optical audio output terminal, connect
the device to this unit’s “OPTICAL” terminal. ( 15, 16, 30)
No surround sound.
≥ Press [SURROUND] to select a surround effect. ( 24)
≥ [BTT770] [BTT370]
(When using the 7.1ch speaker system)
Audio is not available from the surround back speakers even
though Dolby Pro Logic II turns on.
Cannot switch audio.
≥ When audio is output from the HDMI AV OUT terminal, set
“Dolby D/Dolby D +/Dolby TrueHD” or “DTS/DTS-HD” to
“PCM”. ( 38)
No sound from the TV.
≥ Press [EXT-IN] to select the corresponding source. ( 22)
≥ When connecting the unit to a TV using an HDMI cable, check
whether the HDMI terminal on the TV is labeled “HDMI (ARC)”.
If not labeled in this way, connect using the HDMI cable in
combination with an optical digital audio cable.( 14, 15)
≥ If there is no sound from the equipment connected to this
unit’s DIGITAL AUDIO IN terminal, please make sure that
the optical audio output of the equipment is set to PCM.
iPod/iPhone operation
Cannot charge or operate.
≥ Check that the iPod/iPhone is connected firmly. ( 32)
≥ The battery of the iPod/iPhone is depleted. Charge the iPod/
iPhone, and then operate again.
≥ When unexpected operation occurs while using the
iPod/iPhone, connect the iPod/iPhone again or try to restart
the iPod/iPhone.
Cannot display iPod/iPhone videos/photos on the TV.
≥ Make sure that TV is connected to the VIDEO OUT terminal
on this unit. ( 14)
≥ Operate the iPod/iPhone menu to make the appropriate
video/photo output settings for your TV. (Refer to operating
instructions for your iPod/iPhone.)
The TV input channel unintentionally changes to HDMI input.
≥ When the main unit is connected with an “HDAVI Control”
compatible TV and VIDEO IN is selected for iPod/iPhone
video or photo playback, the TV input channel will
automatically change to the HDMI input channel when
[HOME] is pressed.
jRe-select the TV’s VIDEO IN input channel.
SC-BTT770_370_270P_eng.book 45 ページ
2010年12月24日 金曜日 午前10時57分
Radio
Distorted sound or noise is heard.
≥ Adjust the position of the antenna.
≥ Use an outdoor antenna. ( 16)
A beat sound is heard.
≥ Try to keep a certain amount of distance between the
antenna and the TV.
Messages
The following messages or service numbers appear on the
television or unit’s display when something unusual is detected
during startup and use.
On the television
Cannot play.
≥ You inserted an incompatible disc. (Discs recorded in PAL
video, etc.)
[BTT770]
No power.
≥ Ensure the AC power supply cord of the wireless system is
connected properly.
The wireless link indicator is flashing.
≥ There is no link between the main unit and the wireless
system. Turn the wireless system off and then back on.
Alternatively, turn the wireless system off, disconnect the AC
power supply cord and then reconnect it.
The wireless link indicator does not light.
≥ Check that the main unit is turned on, and the wireless
system is turned on.
≥ Ensure that the digital transmitter is fully inserted into the slot
of the main unit. ( 17)
The wireless link indicator keeps flashing between red and
green.
≥ There is a power supply problem. Consult the dealer.
Network
I can’t connect to the network.
≥ Confirm the network connection and settings. ( 17, 20, 40)
≥ Check the operating instructions for each device and
connect accordingly.
Other difficulties with playback
BD-Video or DVD-Video is not played.
≥ Ensure the disc is for the correct BD-Video region code or
DVD-Video region number, and is not defective. ( 8)
≥ You have set a ratings level to limit BD-Video or DVD-Video
play. Change this setting. ( 37)
≥ Some BD-Video can only be output with HDMI.
I cannot play back BD-Live.
≥ The SD card is write-protected. ( 9)
≥ Confirm that this unit is connected to the broadband Internet.
( 17)
≥ Confirm the “BD-Live Internet Access” settings. ( 37)
≥ Confirm an SD Card is inserted into the SD Card slot. ( 22)
Alternative soundtrack and subtitles cannot be selected.
≥ The languages are not recorded on the disc.
≥ You may not be able to use the playback menu to change the
soundtrack and subtitles on some discs. Use the disc’s
menus to make changes. ( 25)
Angle cannot be changed.
≥ Angles can only be changed during scenes where different
angles are recorded.
Cannot display on this unit.
≥ You tried to play a non-compatible image.
No disc is inserted.
≥ The disc may be upside down.
$ This operation is not available.
≥ Some operations are unsupported by the unit. For example;
jBD-Video: During playback, reverse slow-motion or
reverse frame-by-frame is not possible.
IP address is not set.
≥ The “IP Address” in “IP Address / DNS Settings” is “---. ---.
---. ---”. Set the “IP Address”, “Subnet Mask”, and “Default
Gateway”. (Select the automatic address acquisition if
necessary.)
No Video
≥ Depending on the connected iPod/iPhone, video menu may
not be available on the TV. Select “ALL” on the unit’s display
and operate video playback from your iPod/iPhone menu.
( 34)
On the unit’s display
F99
≥ The unit fails to operate properly. Press [POWER Í/I] on the
main unit to switch the unit to standby for 3 seconds. Now
press [POWER Í/I] on the main unit again to turn the unit
on.
U59
≥ The unit is hot.
The unit switches to standby for safety reasons. Wait for
about 30 minutes until the message disappears.
Select a position with good ventilation when installing the
unit. Do not block the ventilation hole on the rear and side of
the unit.
HDMI ONLY
≥ Some BD-Video discs can only be output with HDMI.
NET
≥ While connecting to a network.
Reference
Wireless system (SH-FX71)
VQT3D27
45
VQT3D27~Body_mst.fm 46 ページ
2010年12月24日 金曜日 午後8時27分
No PLAY
≥ There is a viewing restriction on a BD-Video or DVD-Video.
(> 37)
No READ
≥ The media is dirty or badly scratched. The unit cannot play.
PLEASE WAIT
≥ The unit is carrying out an internal process.This is not a
malfunction. You cannot operate the unit while “PLEASE
WAIT” is displayed.
SET 
(“ ” stands for a number.)
≥ The remote control and main unit are using different codes.
Change the code on the remote control.
Press and hold [OK] and the indicated
number button at the same time for
more than 5 seconds.
H or F
(“ ” stands for a number.)
≥ Check and correct the speaker cable connections.
≥ There is something unusual.
≥ Check the unit using the troubleshooting guide. If the service
number does not disappear, do the following.
1 Disconnect the plug from the household AC outlet, wait a
few seconds, then reconnect it.
2 Press [POWER Í/I] to turn the power on.
If the service number does not disappear despite doing the
above, request service from the dealer. Inform the dealer of
the service number when requesting service.
UPD/
(“ ” stands for a number.)
≥ The firmware is being updated. Please do not turn off power.
IPOD OVER CURRENT ERROR
≥ The iPod/iPhone is drawing too much power. Remove the
iPod/iPhone, and turn the unit off and on again.
START
≥ The system is being restarted during the firmware update.
Please do not turn off power.
FINISH
≥ The firmware update is completed.
NOT CONDITIONAL
≥ The requested operation cannot be conducted.
VQT3D27
46
Supplemental
information
∫ Display languages list
Display
ENG
FRA
DEU
ITA
ESP
NLD
SVE
NOR
DAN
POR
RUS
Language
English
French
German
Italian
Spanish
Dutch
Swedish
Norwegian
Danish
Portuguese
Russian
Display
Language
Display
Language
JPN
CHI
KOR
MAL
VIE
THA
POL
CES
SLK
HUN
FIN
Japanese
Chinese
Korean
Malay
Vietnamese
Thai
Polish
Czech
Slovak
Hungarian
Finnish
ARA
HIN
PER
IND
MRI
BUL
RUM
GRE
TUR
Arabic
Hindi
Persian
Indonesian
Maori
Bulgarian
Romanian
Greek
Turkish
Others
∫ Language code list
Language
Code
Abkhazian
6566
Afar:
6565
Afrikaans:
6570
Albanian:
8381
Amharic:
6577
Arabic:
6582
Armenian:
7289
Assamese:
6583
Aymara:
6589
Azerbaijani:
6590
Bashkir:
6665
Basque:
6985
Bengali; Bangla:
6678
Bhutani:
6890
Bihari:
6672
Breton:
6682
Bulgarian:
6671
Burmese:
7789
Byelorussian: 6669
Cambodian:
7577
Catalan:
6765
Chinese:
9072
Corsican:
6779
Croatian:
7282
Czech:
6783
Danish:
6865
Dutch:
7876
English:
6978
Esperanto:
6979
Estonian:
6984
Faroese:
7079
Fiji:
7074
Finnish:
7073
French:
7082
Frisian:
7089
Galician:
7176
Georgian:
7565
German:
6869
Greek:
6976
Greenlandic:
7576
Guarani:
7178
Language
Code
Gujarati:
Hausa:
Hebrew:
Hindi:
Hungarian:
Icelandic:
Indonesian:
Interlingua:
Irish:
Italian:
Japanese:
Javanese:
Kannada:
Kashmiri:
Kazakh:
Kirghiz:
Korean:
Kurdish:
Laotian:
Latin:
Latvian, Lettish:
Lingala:
Lithuanian:
Macedonian:
Malagasy:
Malay:
Malayalam:
Maltese:
Maori:
Marathi:
Moldavian:
Mongolian:
Nauru:
Nepali:
Norwegian:
Oriya:
Pashto, Pushto:
Persian:
Polish:
Portuguese:
Punjabi:
Quechua:
7185
7265
7387
7273
7285
7383
7378
7365
7165
7384
7465
7487
7578
7583
7575
7589
7579
7585
7679
7665
7686
7678
7684
7775
7771
7783
7776
7784
7773
7782
7779
7778
7865
7869
7879
7982
8083
7065
8076
8084
8065
8185
Language
Code
Rhaeto-Romance:
8277
Romanian:
8279
Russian:
8285
Samoan:
8377
Sanskrit:
8365
Scots Gaelic:
7168
Serbian:
8382
Serbo-Croatian: 8372
Shona:
8378
Sindhi:
8368
Singhalese:
8373
Slovak:
8375
Slovenian:
8376
Somali:
8379
Spanish:
6983
Sundanese:
8385
Swahili:
8387
Swedish:
8386
Tagalog:
8476
Tajik:
8471
Tamil:
8465
Tatar:
8484
Telugu:
8469
Thai:
8472
Tibetan:
6679
Tigrinya:
8473
Tonga:
8479
Turkish:
8482
Turkmen:
8475
Twi:
8487
Ukrainian:
8575
Urdu:
8582
Uzbek:
8590
Vietnamese:
8673
Volapük:
8679
Welsh:
6789
Wolof:
8779
Xhosa:
8872
Yiddish:
7473
Yoruba:
8979
Zulu:
9085
SC-BTT770_370_270P_eng.book 47 ページ
2010年12月16日 木曜日 午後9時51分
Java and all Java-based trademarks and logos are trademarks or
registered trademarks of Sun Microsystems, Inc. in the United States
and other countries.
Manufactured under license from Dolby Laboratories.
Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby
Laboratories.
Manufactured under license under U.S. Patent #’s: 5,451,942;
5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535; 7,392,195;
7,272,567; 7,333,929; 7,212,872 & other U.S. and worldwide patents
issued & pending.
DTS and the Symbol are registered trademarks, & DTS-HD, DTS-HD
Master Audio | Essential and the DTS logos are trademarks of DTS, Inc.
Product includes software.
© DTS, Inc. All Rights Reserved.
This item incorporates copy protection technology that is protected by
U.S. patents and other intellectual property rights of Rovi Corporation.
Reverse engineering and disassembly are prohibited.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing LLC in the
United States and other countries.
This product is licensed under the AVC patent portfolio license and
VC-1 patent portfolio license for the personal and non-commercial use
of a consumer to (i) encode video in compliance with the AVC Standard
and VC-1 Standard (“AVC/VC-1 Video”) and/or (ii) decode AVC/VC-1
Video that was encoded by a consumer engaged in a personal and
non-commercial activity and/or was obtained from a video provider
licensed to provide AVC/VC-1 Video. No license is granted or shall be
implied for any other use. Additional information may be obtained from
MPEG LA, LLC.
See http://www.mpegla.com.
HDAVI Control™ is a trademark of Panasonic Corporation.
“Made for iPod” and “Made for iPhone” mean that an electronic
accessory has been designed to connect specifically to iPod, or
iPhone, respectively, and has been certified by the developer to meet
Apple performance standards.
Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod, or iPhone may
affect wireless performance.
iPhone, iPod, iPod classic, iPod nano, and iPod touch are trademarks
of Apple Inc., registered in the U.S. and other countries.
This product incorporates the following software:
(1) the software developed independently by or for Panasonic
Corporation,
(2) the software owned by third party and licensed to Panasonic
Corporation,
(3) the software licensed under the GNU General Public License,
Version 2 (GPL v2),
(4) the software licensed under the GNU LESSER General Public
License, Version 2.1 (LGPL v2.1) and/or,
(5) open sourced software other than the software licensed under the
GPL v2 and/or LGPL v2.1
For the software categorized as (3) and (4), please refer to the terms
and conditions of GPL v2 and LGPL v2.1, as the case may be at
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html and
http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html.
In addition, the software categorized as (3) and (4) are copyrighted by
several individuals. Please refer to the copyright notice of those
individuals at
http://www.am-linux.jp/dl/AWBPP11
The GPL/LGPL software is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY, without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
At least three (3) years from delivery of products, Panasonic will give to
any third party who contacts us at the contact information provided
below, for a charge no more than our cost of physically performing
source code distribution, a complete machine-readable copy of the
corresponding source code covered under GPL v2/LGPL v2.1.
VIERA Link™ is a trademark of Panasonic Corporation.
Contact Information
cdrequest@am-linux.jp
VIERA CAST™ is a trademark of Panasonic Corporation.
EZ Sync™ is a trademark of Panasonic Corporation.
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS
and Thomson.
“AVCHD” and the “AVCHD” logo are trademarks of Panasonic
Corporation and Sony Corporation.
SDXC Logo is a trademark of SD-3C, LLC.
For the software categorized as (5) includes as follows.
1. This product includes software developed by the OpenSSL Project
for use in the OpenSSL Toolkit.
(http://www.openssl.org/)
2. This product includes software developed by the University of
California, Berkeley and its contributors.
3. FreeType code.
4. The Independent JPEG Group's JPEG software.
The Wi-Fi CERTIFIED Logo is a certification mark of the Wi-Fi Alliance.
YouTube and Picasa are trademarks of Google, Inc.
” logo are trade
Part of the software embedded in this product is gSOAP software.
Portions created by gSOAP are Copyright (C) 2001-2009 Robert A. van
Engelen, Genivia inc. All Rights Reserved.
THE SOFTWARE IN THIS PRODUCT WAS IN PART PROVIDED BY
GENIVIA INC AND ANY EXPRESS OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE
FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED
TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
Reference
gSOAP Public License 1.3
“DVD Logo” is a trademark of DVD Format/Logo Licensing Corporation.
Skype, associated trade marks and logos and the “
marks of Skype Limited.
Source code is also freely available to you and any other member of
the public via our website below.
http://www.am-linux.jp/dl/AWBPP11
VQT3D27
47
VQT3D27~Body_mst.fm 48 ページ
2011年1月6日 木曜日 午後2時9分
Specifications
GENERAL
Power consumption:
85 W
Power consumption in standby mode:
[BTT770] [BTT370] Approx. 0.05 W
[BTT270] [BTT273] Approx. 0.4 W
Power supply:
AC 120 V, 60 Hz
iPod/iPhone Connector:
[BTT770] [BTT370]
Communication Camera
(Rear USB):
Dimensions (WkHkD):
DC OUT 5 V 1.0 A MAX
DC OUT 5 V 500 mA MAX
(1615/16qk19/16qk1031/32q)
[BTT370] [BTT270] [BTT273] 430 mmk38 mmk279 mm
(1615/16qk11/2qk1031/32q)
Mass (Weight):
[BTT770] Approx. 3 kg (6.6 lbs)
[BTT370] [BTT270] [BTT273] Approx. 2.7 kg (6 lbs)
(Dimensions and Weight do not
include speakers)
Operating temperature range:
0 oC to 40 oC
(32 oF to 104 oF)
Operating humidity range:
35 % to 80 % RH
(no condensation)
AMPLIFIER SECTION
RMS TTL POWER OUTPUT:
1000 W*
1 kHz, 10 % total harmonic distortion
FRONT:
[BTT770] 185 W per ch (3 ≠)
[BTT370] [BTT270] [BTT273] 160 W per ch (3 ≠)
CENTER:
[BTT770] 180 W per ch (3 ≠)
[BTT370] [BTT270] [BTT273] 160 W per ch (3 ≠)
SURROUND:
[BTT770] 125 W per ch (3 ≠)
[BTT370] [BTT270] [BTT273] 160 W per ch (3 ≠)
100 Hz, 10 % total harmonic distortion
SUBWOOFER:
200 W per ch (3 ≠)
FTC TTL POWER OUTPUT:
430 W
120 Hz to 20 kHz, 1.0 % total harmonic distortion
FRONT:
60 W per ch (3 ≠)
CENTER:
90 W per ch (3 ≠)
SURROUND:
60 W per ch (3 ≠)
45 Hz to 120 Hz, 1.0 % total harmonic distortion
SUBWOOFER:
100 W (3 ≠)
Audio Input
AUX:
k1
Digital Audio Input
Optical:
k1
k2
32 kHz, 44.1 kHz, 48 kHz
PCM, Dolby Digital, DTS
* [BTT370] When using SH-FX71(optional), RMS TTL power output is
changed to 930 W.
FM TUNER SECTION
48
Frequency range:
Antenna terminals:
Tweeter:
Impedance:
Output sound pressure:
Frequency range:
Dimensions (WkHkD):
87.9 MHz to 107.9 MHz (200 kHz step),
87.5 MHz to 108.0 MHz (100 kHz step)
75 ≠ (unbalanced)
2 WAY 3 SPEAKER Bass-ref.
3.5 cm k 10 cm (13/8qk4q) CONE
TYPEk 2
2.5 cm (1q) SEMI-DOME TYPE
3≠
78 dB/W (1 m)
100 Hz to 30 kHz (j16 dB),
130 Hz to 25 kHz (j10 dB)
255 mmk1024 mmk255 mm
(101/16qk4011/32qk101/16q)
Approx. 2.3 kg (5.07 lbs)
[BTT370] [BTT273] SB-HF370
Type:
Woofer:
Tweeter:
Impedance:
Output sound pressure:
Frequency range:
Dimensions (WkHkD):
Mass (Weight):
2 WAY 2 SPEAKER Bass-ref.
6.5 cm (21/2q) CONE TYPE
2.5 cm (1q) SEMI-DOME TYPE
3≠
78 dB/W (1 m)
85 Hz to 25 kHz (j16 dB),
105 Hz to 24 kHz (j10 dB)
135 mmk404 mmk135 mm
(55/16qk1529/32qk55/16q)
Approx. 0.82 kg (1.81 lbs)
[BTT270] SB-HF270
Type:
Full range:
Impedance:
Output sound pressure:
Frequency range:
Dimensions (WkHkD):
Mass (Weight):
CENTER SPEAKER
[BTT770] SB-HC775
Type:
Woofer:
Tweeter:
Impedance:
Output sound pressure:
Frequency range:
Dimensions (WkHkD):
Mass (Weight):
1 WAY 1 SPEAKER Bass-ref.
6.5 cm (21/2q) CONE TYPE
3≠
78 dB/W (1 m)
105 Hz to 25 kHz (j16 dB),
130 Hz to 22 kHz (j10 dB)
80 mmk117 mmk70.5 mm
(35/32qk419/32qk215/16q)
Approx. 0.35 kg (0.77 lbs)
2 WAY 3 SPEAKER Bass-ref.
3.5 cm k 10 cm (13/8qk4q) CONE
TYPEk 2
2.5 cm (1q) SEMI-DOME TYPE
3≠
78 dB/W (1 m)
100 Hz to 30 kHz (j16 dB),
130 Hz to 25 kHz (j10 dB)
424 mmk59 mmk76 mm
(1623/32qk211/32qk3q)
Approx. 1.06 kg (2.34 lbs)
[BTT370] [BTT273] SB-HC370
Type:
Full range:
Impedance:
Output sound pressure:
Frequency range:
Dimensions (WkHkD):
[BTT770] [BTT370] HDMI AV
VQT3D27
FRONT SPEAKERS
[BTT770] SB-HF775
Type:
Woofer:
Mass (Weight):
[BTT770] 430 mmk40 mmk279 mm
input:
Sampling frequency:
Audio Format:
SPEAKER SECTION
Mass (Weight):
1 WAY 1 SPEAKER Bass-ref.
6.5 cm (21/2q) CONE TYPE
3≠
78 dB/W (1 m)
95 Hz to 25 kHz (j16 dB),
120 Hz to 22 kHz (j10 dB)
145 mmk81 mmk70.5 mm
(523/32qk33/16qk215/16q)
Approx. 0.515 kg (1.14 lbs)
[BTT270] SB-HC270
Type:
Full range:
Impedance:
Output sound pressure:
Frequency range:
Dimensions (WkHkD):
Mass (Weight):
1 WAY 1 SPEAKER Bass-ref.
6.5 cm (21/2q) CONE TYPE
3≠
79 dB/W (1 m)
90 Hz to 25 kHz (j16 dB),
115 Hz to 22 kHz (j10 dB)
145 mmk81 mmk70.5 mm
(523/32qk33/16qk215/16q)
Approx. 0.5 kg (1.1 lbs)
VQT3D27~Body_mst.fm 49 ページ
SURROUND SPEAKERS
SB-HS270
Type:
Full range:
Impedance:
Output sound pressure:
Frequency range:
Dimensions (WkHkD):
Mass (Weight):
2011年1月20日 木曜日 午後1時54分
SUBWOOFER
[BTT770] [BTT370] SB-HW370
Type:
Woofer:
Impedance:
Output sound pressure:
Frequency range:
Dimensions (WkHkD):
Mass (Weight):
1 WAY 1 SPEAKER Bass-ref.
16 cm (61/2q) CONE TYPE
3≠
78 dB/W (1 m)
30 Hz to 220 Hz (j16 dB),
35 Hz to 180 Hz (j10 dB)
180 mmk408 mmk300 mm
(73/32qk161/16qk1113/16q)
Approx. 4.3 kg (9.5 lbs)
[BTT270] [BTT273] SB-HW270
Type:
Woofer:
Impedance:
Output sound pressure:
Frequency range:
Dimensions (WkHkD):
Mass (Weight):
1 WAY 1 SPEAKER Bass- ref.
16 cm (61/2q) CONE TYPE
3≠
78 dB/W (1 m)
40 Hz to 220 Hz (j16 dB),
45 Hz to 180 Hz (j10 dB)
145 mmk289.5 mmk258 mm
(523/32qk1113/32qk105/32q)
Approx. 3.0 kg (6.6 lbs)
TERMINAL SECTION
SD card slot:
Ethernet:
WLAN
Antenna:
Standard Compliance:
Transmission system:
Transfer rate (Standard)*:
IEEE802.11n:
IEEE802.11g / IEEE802.11a:
IEEE802.11b:
Access Mode:
Security:
WIRELESS SYSTEM
AND DIGITAL TRANSMITTER
[BTT770]
1 WAY 1 SPEAKER Bass-ref.
6.5 cm (21/2q) CONE TYPE
3≠
78 dB/W (1 m)
105 Hz to 25 kHz (j16 dB),
130 Hz to 22 kHz (j10 dB)
80 mmk117 mmk70.5 mm
(35/32qk419/32qk215/16q)
Approx. 0.35 kg (0.77 lbs)
<AMPLIFIER SECTION>
RMS TTL POWER OUTPUT:
250 W
1 kHz, 10 % total harmonic distortion
SURROUND:
125 W per ch (3 ≠)
FTC TTL POWER OUTPUT:
68 W
120 Hz to 20 kHz, 1.0 % total harmonic distortion
SURROUND:
34 W per ch (3 ≠)
<RF SECTION>
Wireless module
Frequency range:
2.4 to 2.4835 GHz
No. of channels:
3
<GENERAL>
Power supply:
AC 120 V, 60 Hz
Power consumption
Digital transmitter:
1.2 W
Wireless system:
35 W
Power consumption
in off mode:
Approx. 0.2 W
Dimensions (WkHkD):
Digital transmitter:
43.3 mmk37.3 mmk8.2 mm
(111/16qk115/32qk5/16q)
Wireless system:
165 mmk91.5 mmk164 mm
(61/2qk35/8qk615/32q)
Mass (Weight)
Digital transmitter:
Approx. 0.01 kg (0.02 lbs)
Wireless system:
Approx. 0.66 kg (1.46 lbs)
Operating temperature range: 0 oC to 40 oC
(32 oF to 104 oF)
Operating humidity range:
35 % to 80 % RH
(no condensation)
Specifications are subject to change without notice.
Connector: 1 system
10BASE-T/100BASE-TX 1 system
Tx 1, Rx 2
IEEE802.11n / IEEE802.11a /
IEEE802.11g / IEEE802.11b
MISO-OFDM system,
OFDM system, DSSS system
Tx Max. 150 Mbps, Rx Max. 300 Mbps
Max. 54 Mbps
Max. 11 Mbps
Infrastructure mode
WPA2-PSK (TKIP/AES)
WPA-PSK (TKIP/AES)
WEP (64 bit / 128 bit)
(This unit supports WPA and WPA2
encryption.)
* Transfer rates are theoretical values; however, actual communication rate will
vary according to communication environment or connected equipment.
File format
File
format
MP3
JPEG
Extension
Reference
“.MP3”,
“.mp3“
ID3 tags (Only titles and the names
of artists)
“.JPG”,
“.jpg“
≥ MOTION JPEG and Progressive
JPEG is not supported
≥ You may not be able to play back
the file if you have edited the
folder structure or the file name
on a PC or other device.
≥ With certain recording states and folder structures, the play
order may differ or playback may not be possible.
VIDEO SECTION
LASER Specification:
Class I LASER Product
Wave length:
Laser power:
NTSC
1.0 Vp-p (75 ≠)
Pin jack (1 system)
1080p/1080i/720p/480p
Type A (19 pin)
This unit supports “HDAVI Control 5”
function.
790 nm (CDs)/655 nm (DVDs)/
405 nm (BDs)
No hazardous radiation is emitted
with the safety protection
Reference
Signal system:
Video output
Output level:
Output connector:
HDMI AV output
Output format:
Output connector:
VQT3D27
49
VQT3D27~Body3_eng.fm 50 ページ
2011年1月8日 土曜日 午後12時13分
Limited Warranty (ONLY FOR U.S.A. AND PUERTO RICO)
Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus, New Jersey 07094
Panasonic Blu-ray and DVD Products Limited Warranty
Limited Warranty Coverage (For USA and Puerto Rico Only)
If your product does not work properly because of a defect in materials
or workmanship, Panasonic Consumer Electronics Company (referred
to as “the warrantor”) will, for the length of the period indicated on the
chart below, which starts with the date of original purchase (“warranty
period”), at its option either (a) repair your product with new or
refurbished parts, (b) replace it with a new or a refurbished equivalent
value product, or (c) refund your purchase price. The decision to repair,
replace or refund will be made by the warrantor.
Product or Part Name
Parts
Labor
Blu-ray Disc Player, Portable
Blu-ray Disc Player
1 year
90 days
Blu-ray Home Theater System
1 year
1 year
DVD Player, Portable DVD Player 1 year
90 days
DVD Recorder
90 days
1 year
Rechargeable Batteries (pack),
10 days
DVD-RAM Disc (defective exchange)
Not
Applicable
During the “Labor” warranty period there will be no charge for labor.
During the “Parts” warranty period, there will be no charge for parts.
This Limited Warranty excludes both parts and labor for
non-rechargeable batteries, antennas, and cosmetic parts (cabinet).
This warranty only applies to products purchased and serviced in the
United States or Puerto Rico. This warranty is extended only to the
original purchaser of a new product which was not sold “as is”.
Mail-In Service
For assistance in the U.S.A. and Puerto Rico in obtaining repairs,
please ship the product prepaid to:
Panasonic Exchange Center
4900 George McVay Drive
Suite B
McAllen, TX 78503
panacare@us.panasonic.com
When shipping the unit, carefully pack, include all accessories, and
send it prepaid, adequately insured and preferably in the original carton.
When shipping Lithium Ion batteries please visit our Web Site at
www.panasonic.com/BatteryHandling as Panasonic is committed to
providing the most up to date information. Include a letter detailing the
complaint, a return address and provide a daytime phone number
where you can be reached. A valid registered receipt is required under
the Limited Warranty.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE
PURCHASER WILL BE REQUIRED TO FURNISH A SALES
RECEIPT/PROOF OF PURCHASE INDICATING DATE OF
PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE.
CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT
RECEIVED WITHOUT SUCH PROOF OF PURCHASE.
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or
workmanship, and DOES NOT COVER normal wear and tear or
cosmetic damage. The warranty ALSO DOES NOT COVER damages
which occurred in shipment, or failures which are caused by products
not supplied by the warrantor, or failures which result from accidents,
misuse, abuse, neglect, mishandling, misapplication, alteration, faulty
installation, set-up adjustments, misadjustment of consumer controls,
improper maintenance, power line surge, lightning damage,
modification, introduction of sand, humidity or liquids, commercial use
such as hotel, office, restaurant, or other business or rental use of the
product, or service by anyone other than a Factory Service Center or
other Authorized Servicer, or damage that is attributable to acts of God.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED
UNDER “LIMITED WARRANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS
PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY.
(As examples, this excludes damages for lost time, travel to and from
the servicer, loss of or damage to media or images, data or other
memory or recorded content. The items listed are not exclusive, but for
illustration only.)
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE
WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE
PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty
lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have
other rights which vary from state to state. If a problem with this product
develops during or after the warranty period, you may contact your
dealer or Service Center. If the problem is not handled to your
satisfaction, then write to the warrantor’s Consumer Affairs Department
at the addresses listed for the warrantor.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS
LIMITED WARRANTY, ARE YOUR RESPONSIBILITY.
Customer Services Directory (United States and Puerto
Rico)
Obtain Product Information and Operating Assistance; locate
your nearest Dealer or Service Center; purchase
Parts and Accessories; or make Customer Service and
Literature requests by visiting our Web Site at:
http://www.panasonic.com/help
or, contact us via the web at:
http://www.panasonic.com/contactinfo
You may also contact us directly at:
1-800-211-PANA (7262)
Monday-Friday 9am-9pm,
Saturday-Sunday 10am-7pm EST
For hearing or speech impaired TTY users, TTY:
1-877-833-8855
Accessory Purchases (United States and Puerto Rico)
Purchase Parts, Accessories and Instruction Books online for all
Panasonic Products by visiting our Web Site at:
http://www.pstc.panasonic.com
Or, send your request by E-mail to:
npcparts@us.panasonic.com
You may also contact us directly at:
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only)
(Monday-Friday 9am-9pm EST)
Panasonic Service and Technology Company
20421 84th Avenue South, Kent, WA 98032
(We accept Visa, MasterCard, Discover Card, American Express, and
Personal Checks)
For hearing or speech impaired TTY users, TTY: 1-866-605-1277
As of December 2010
User memo:
DATE OF PURCHASE ________________________
DEALER NAME ______________________________
DEALER ADDRESS __________________________
___________________________________________
TELEPHONE NUMBER _______________________
VQT3D27
50
The model number and serial number of this product can be
found on either the back or the bottom of the unit.
Please note them in the space provided below and keep for
future reference.
MODEL NUMBER _____________________________
SERIAL NUMBER _____________________________
SC-BTT770_370_270P_eng.book 51 ページ
2010年12月16日 木曜日 午後9時51分
Limited Warranty (Only for CANADA)
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
PANASONIC PRODUCT - LIMITED WARRANTY
Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship under normal use and for a
period as stated below from the date of original purchase agrees to, at its option either (a) repair your product with new or
refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price. The
decision to repair, replace or refund will be made by Panasonic Canada Inc.
Technics Audio Product - One (1) year, parts and labour
Panasonic BD/DVD Product - One (1) year, parts and labour
Panasonic Audio Receivers - One (1) year, parts and labour
Home Theater Systems Product - One (1) year, parts and labour
This warranty is given only to the original purchaser, or the person for whom it was purchased as a gift, of a Panasonic brand
product mentioned above sold by an authorized Panasonic dealer in Canada and purchased and used in Canada, which product
was not sold "as is", and which product was delivered to you in new condition in the original packaging.
IN ORDER TO BE ELIGIBLE TO RECEIVE WARRANTY SERVICE HEREUNDER, A PURCHASE RECEIPT OR OTHER
PROOF OF DATE OF ORIGINAL PURCHASE, SHOWING AMOUNT PAID AND PLACE OF PURCHASE IS REQUIRED
LIMITATIONS AND EXCLUSIONS
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and
tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are
caused by products not supplied by Panasonic Canada Inc., or failures which result from accidents, misuse, abuse, neglect,
mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper
maintenance, power line surge, lightning damage, modification, introduction of sand, humidity or liquids, commercial use such as
hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than an Authorized Servicer, or
damage that is attributable to acts of God.
Dry cell batteries are also excluded from coverage under this warranty.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL
PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES RESULTING
FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY.
(As examples, this warranty excludes damages for lost time, travel to and from the Authorized Servicer, loss of or damage to
media or images, data or other memory or recorded content. This list of items is not exhaustive, but for illustration only.)
In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the
exclusion of implied warranties, so the above limitations and exclusions may not be applicable. This warranty gives you specific
legal rights and you may have other rights which vary depending on your province or territory.
WARRANTY SERVICE
For product operation and information assistance, please contact:
Customer Care Centre:
Telephone #: 1-800-561-5505
Fax #: (905) 238-2360
Email link: “Support # contact us # email” on www.panasonic.ca
PRODUCT REPAIRS
Reference
PRODUCT OPERATION ASSISTANCE
Please locate your nearest Authorized Servicentre.
Link: “Support # Panasonic Servicentre® locator” on www.panasonic.ca
IF YOU SHIP THE PRODUCT TO A SERVICENTRE
Carefully pack and send prepaid, adequately insured and preferably in the original carton.
Include details of the defect claimed, and proof of date of original purchase.
VQT3D27
51
VQT3D27~BCover_eng.fm
52 ページ 2011年1月6日 木曜日 午後1時43分
Index
A
Audio
Changing audio. . . . . . . . . . . . . . . . .25
Language . . . . . . . . . . . . . . . . . .35, 37
B
BD-Live. . . . . . . . . . . . . . . . . . . . . . . . . .26
C
Chapter. . . . . . . . . . . . . . . . . . . . . . . . . .26
F
File format . . . . . . . . . . . . . . . . . . . . . . .49
Firmware update . . . . . . . . . . . . . . . . . .22
I
iPod/iPhone . . . . . . . . . . . . . . . . . . . . . .32
L
LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Language
Audio . . . . . . . . . . . . . . . . . . . . . 35, 37
Menu . . . . . . . . . . . . . . . . . . . . . . . . 37
On-screen . . . . . . . . . . . . . . . . . . . . 38
Soundtrack. . . . . . . . . . . . . . . . . . . . 35
Subtitle . . . . . . . . . . . . . . . . . . . . 35, 37
N
Network
Connection. . . . . . . . . . . . . . . . . . . . 17
Setting . . . . . . . . . . . . . . . . . . . . 20, 40
P
Playlists. . . . . . . . . . . . . . . . . . . . . . . . . 26
Pop-up menu . . . . . . . . . . . . . . . . . . . . 25
R
Radio . . . . . . . . . . . . . . . . . . . . . . . . . .
Re-master . . . . . . . . . . . . . . . . . . . . . . .
Restore Default Settings. . . . . . . . . . .
Resume play function . . . . . . . . . . . . .
29
36
40
25
S
Subtitle . . . . . . . . . . . . . . . . . . . . . . . . . 35
V
VIERA CASTTM . . . . . . . . . . . . . . . . . . . 34
VIERA LinkTM “HDAVI ControlTM” . . . . 31
W
Wireless LAN . . . . . . . . . . . . . . . . . . . . 17
24p . . . . . . . . . . . . . . . . . . . . . . . . . 36, 39
3D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Q
Quick Start . . . . . . . . . . . . . . . . . . . . . . 40
®
As an ENERGY STAR Partner, Panasonic has determined that
®
this product meets the ENERGY STAR guidelines for energy efficiency.
For Canada only: The word “Participant” is used in place of the word “Partner”.
[BTT770] : Main unit only
Panasonic Consumer Electronics Company,
Division of Panasonic Corporation of North America
One Panasonic Way, Secaucus,
New Jersey 07094
http://www.panasonic.com
Panasonic Corporation 2010
Printed in Malaysia
Panasonic Canada Inc.
5770 Ambler Drive
Mississauga, Ontario
L4W 2T3
www.panasonic.ca
VQT3D27-3
F1210MH3011
Download PDF

advertising