- Computers & electronics
- Computer components
- Chassis components
- Mounting kits
- Chief
- KTA1005B
- Installation instructions
advertisement
I N S T A L L A T I O N I N S T R U C T I O N S
Array Centris Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
KTA1005
KTA1005
DISCLAIMER
Milestone AV Technologies, Inc., and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief® and Centris™ are trademarks of Milestone AV
Technologies. All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING:
A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.
Installation Instructions
CAUTION:
A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.
WARNING:
Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.
WARNING:
Failure to provide adequate structural strength for the installation of this kit can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this mount is attached can support five times the combined weight of all equipment.
WARNING:
Exceeding the weight capacity can result in serious personal injury or damage to equipment! See the installation instructions that came with the array onto which this accessory is being installed for weight limits. The accessory’s weight capacity is 40 lbs (18.1 kg).
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Сожмите Застежку
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Ослабьте Застежку
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Приспособьтесь
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Главный ведьмой Рывок
2
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION AND PARTS
KTA1005
I/M x1
A (1)
B (4)
M4 x 12mm
C (4)
M4 x 20mm
D (4)
M4 x 30mm
E (4)
.50 x .194 x .375
F (4)
.50 x .194 x .750
3
KTA1005
ASSEMBLY and INSTALLATION
The following procedure assumes a base and pole have been purchased and are available. The procedure also assumes that no displays are mounted to the array.
1.
Assemble pole and base following instructions included with those kits.
2.
Slide display with Centris bracket onto mounting rail.
(See Figure 1)
4
Tighten to mounting rail
Installation Instructions
WARNING:
IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Support and arrange existing monitors or devices along with those being installed to ensure an overall balanced weight distribution.
This is especially important in free-standing units.
Display Installation - Flush Mount Display
1.
Start two M4 x 12mm Phillips pan head screws (B) into upper mounting holes in display back. (See Figure 2)
NOTE:
Leave at least 1/8" of each screw protruding out back of display.
Array
Square Nut
KTA-1005
End Lock
Figure 1
3.
Install end locks into mounting rail. (See Figure 1)
4.
Tighten inner knob to tighten array head to mounting rail.
5.
Determine mounting pattern on display.
WARNING:
IMPROPER INSTALLATION CAN LEAD TO
EQUIPMENT FALLING CAUSING SERIOUS PERSONAL
INJURY AND DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
WARNING:
IMPROPER INSTALLATION CAN LEAD TO
ELECTRIC SHOCK OR DAMAGE TO EQUIPMENT! Screw length must not exceed the depth of threaded mounting insert in display.
WARNING:
IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of improper size may damage your display! Proper screws will easily and completely thread into display mounting holes.
Ensure that screws are not too long.
Figure 2
2
1
WARNING:
IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Inadequate thread engagement in display may cause display to fall! Back out screws ONLY as necessary to allow installation of mounting plate!
5.
Tighten all hardware.
Figure 3
4
3
(B) x 2
2.
Align two screws in display back with upper teardrop mounting holes in KTA-1005.
3.
Place two screws in display back into upper teardrop mounting holes in KTA-1005 and lower display until screws are seated in lower area of teardrop mounting holes.
(See Figure 3)
4.
Install two screws through display mounting plate and into lower mounting holes in display back. (See Figure 3)
(B) x 2
4
Installation Instructions
Display Installation - Recessed Mount Display
1.
Secure display to Centris head using four 3/8" (E) or 3/4" (F) nylon spacers, and four M4 x 20mm (C) or four M4 x 30mm
(D) Phillips pan head screws into four mounting holes in display back. (See Figure 4)
(C or D) x 4
(E or F) x 4
Figure 4
Adjustments
1.
Tighten the outer knob to adjust pitch tension.(See Figure 5)
Adjust pitch tension
Figure 5
KTA1005
5
KTA1005 Installation Instructions
6
Installation Instructions KTA1005
7
KTA1005 Installation Instructions
Chief Manufacturing, a division of
Milestone AV Technologies
8832-000257
©2008 Milestone AV Technologies www.chiefmfg.com
07/08
USA/International A
8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280
F
877.894.6918 / 952.894.6918
Europe
Asia Pacific
A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P
+31 (0)40 2668620
F +31 (0)40 2668615
A
Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
P +86-755-8996 9226
F
+86-755-8996 9217
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project